# Boeing Alert Requirements Bulletin 737-22A1399 RB: No revision named

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2024-1897; AD 2024-23-03 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Alert Requirements Bulletin 737-22A1399 RB](https://openairdocs.org/service-documents/boeing/737-22a1399-rb.md)
- Title as filed: 737-22A1399 RB
- Pages: 45
- PDF: https://openairdocs.org/files/sha256/97/b3/97b349a8966421adff2a2342f1e612db138cb5739eae1a0ed739f75ea981fe44
- Page: https://openairdocs.org/service-documents/boeing/737-22a1399-rb/file/97b349a89664

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Commercial 
Airplanes
737
Requirements Bulletin
ALERT
Number: 737-22A1399 RB
Original Issue: April 13, 2023
ATA System: 2211
SUBJECT: AUTO FLIGHT - Digital Flight Control System - Mechanical Aileron Force Limiter (MAFL)
To Electronic Aileron Limiter (EAL) Replacement
EXPORT CONTROLLED - This technology or software is subject to the U.S. Export Administration Regulations
(EAR), (15 C.F.R. Parts 730-774). No authorization from the U.S. Department of Commerce is required for
export, re-export, in-country transfer, or access EXCEPT to country group E:1 or E:2 countries/persons per
Supp.1 to Part 740 of the EAR.
9E991ECCN:
Copyright © 2023 Boeing.
Unpublished Work. All Rights Reserved.
Treatment of this document and its content is governed by contract with Boeing. Rights to use this document
are licensed on a per aircraft basis and such rights may not be transferable. For more information, contact The
Boeing Company.
Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner,
BBJ, DC-8, DC-9, DC-10, KC-10, KC-46, KDC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8, Poseidon and
Boeing liveries are all trademarks owned by The Boeing Company; and no trademark license is granted in
connection with this document unless provided in writing by Boeing.
Original Issue: April 13, 2023
737-22A1399 RB
1 of 45
5.0

### Page 2

Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 13, 2023
737-22A1399 RB
2 of 45
REQUIREMENTS BULLETIN 737-22A1399
ALERTALERT
BLANK PAGE

### Page 3

Table of Contents
1. EFFECTIVITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
A. Airplanes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
B. Spares Affected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2. CONCURRENT REQUIREMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3. COMPLIANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4. APPROVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
5. ACCOMPLISHMENT INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
A. General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
B. Work Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
FIGURE 1: P18-1 PANEL - CIRCUIT BREAKER C723 - DEACTIVATE . . . . . . . . . . . . . . . . . 19
FIGURE 2: P18-1 PANEL - WIRE BUNDLE W029 - WIRING CHANGE . . . . . . . . . . . . . . . . . 21
FIGURE 3: LOWER NOSE COMPARTMENT - MECHANICAL AILERON FORCE LIMITER (MAFL) -
REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
FIGURE 4: LOWER NOSE COMPARTMENT - MAFL HOUSING ASSEMBLY - INSTALLATION . . . 24
FIGURE 5: LOWER NOSE COMPARTMENT - WIRE BUNDLE W369 - WIRING CHANGE . . . . . . 26
FIGURE 7: E1-3 ELECTRONICS SHELF - WIRE BUNDLES W011 AND W069 - WIRE ROUTING . . 28
FIGURE 8: E1-3 ELECTRONICS SHELF - WIRE BUNDLE W069 - WIRING CHANGE [Group 1] . . . 29
FIGURE 9: E1-3 ELECTRONICS SHELF - WIRE BUNDLE W011 - WIRING CHANGE [Group 1] . . . 31
FIGURE 10: E1-3 ELECTRONICS SHELF - WIRE BUNDLE W069 - WIRING CHANGE [Group 2] . . . 33
FIGURE 11: E1-3 ELECTRONICS SHELF - WIRE BUNDLE W011 - WIRING CHANGE [Group 2] . . . 35
FIGURE 12: E1-3 ELECTRONICS SHELF - WIRE BUNDLE W069 - WIRING CHANGE [Group 3] . . . 37
FIGURE 13: E1-3 ELECTRONICS SHELF - WIRE BUNDLE W011 - WIRING CHANGE [Group 3] . . . 39
FIGURE 14: E1-3 ELECTRONICS SHELF - WIRE BUNDLE W069 - WIRING CHANGE [Group 4] . . . 41
FIGURE 15: E1-3 ELECTRONICS SHELF - WIRE BUNDLE W011 - WIRING CHANGE [Group 4] . . . 43
APPENDIX C: TESTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 13, 2023
737-22A1399 RB
3 of 45
REQUIREMENTS BULLETIN 737-22A1399
ALERTALERT

### Page 4

Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 13, 2023
737-22A1399 RB
4 of 45
REQUIREMENTS BULLETIN 737-22A1399
ALERTALERT
BLANK PAGE

### Page 5

Commercial 
Airplanes
737
Requirements Bulletin
ALERT
Number: 737-22A1399 RB
Original Issue: April 13, 2023
ATA System: 2211
SUBJECT: AUTO FLIGHT - Digital Flight Control System - Mechanical Aileron Force Limiter (MAFL)
To Electronic Aileron Limiter (EAL) Replacement
THIS DOCUMENT IS SENT TO THE OPERATORS OF RECORD OF THE AIRPLANES SHOWN IN
PARAGRAPH 1.A., EFFECTIVITY. IF AN AIRPLANE HAS BEEN LEASED OR SOLD, SEND THIS DOCUMENT
TO THE NEW OPERATOR. IF APPLICABLE SPARES HAVE BEEN SOLD, SEND THIS DOCUMENT TO THE
NEW OWNER. THIS IS AN ENHANCED REQUIRED FOR COMPLIANCE DOCUMENT. THE BOEING
PROCESSES USED TO CREATE THE SERVICE BULLETIN (SB) AND THE REQUIREMENTS BULLETIN
(RB) ENSURE THAT THE INFORMATION BETWEEN "RC START" AND "RC END" IN THE SB ARE IDENTICAL
TO THE INFORMATION IN THE SAME SECTIONS (COMPLIANCE, WORK INSTRUCTIONS…) OF THE RB
WHICH THE SB REFERS TO AS THE RELATED DOCUMENT.
1. Effectivity
A. Airplanes
This bulletin is applicable to 737-300, 737-400 Airplane(s), line number(s) 1015, 1043, 1073, 1098,
1103-1104, 1106, 1125-1126, 1128, 1130, 1134, 1140, 1146-1147, 1153, 1158, 1162, 1168,
1174-1175, 1192, 1198, 1200, 1204, 1207-1208, 1212, 1215-1216, 1221-1222, 1224, 1227, 1229,
1237, 1239-1240, 1242, 1251, 1258-1260, 1263-1264, 1272, 1274, 1277, 1284, 1286, 1288-1291,
1294, 1301, 1304, 1306, 1309-1310, 1312, 1316, 1320, 1327, 1335, 1337, 1339, 1341, 1344,
1352, 1356-1358, 1363, 1365, 1372, 1375, 1381, 1388, 1390, 1393, 1395, 1398, 1406, 1409,
1421, 1423, 1425, 1432, 1434, 1436, 1439, 1441, 1443-1445, 1454, 1458, 1461, 1463, 1465,
1467, 1469, 1474-1475, 1477, 1481, 1484-1485, 1487, 1492-1493, 1498-1499, 1501, 1504,
1507-1509, 1512, 1514-1516, 1519, 1528, 1532, 1534-1535, 1537, 1539, 1542, 1547, 1550, 1552,
1555, 1559, 1564, 1567, 1570-1571, 1577, 1582, 1586-1587, 1589, 1600, 1602, 1609, 1614, 1617,
1619, 1621, 1623, 1625, 1628, 1630, 1634-1635, 1638-1639, 1645, 1651-1652, 1657, 1660, 1662,
1666-1667, 1674-1677, 1679-1680, 1683, 1685, 1687, 1689, 1691, 1693-1694, 1696-1702, 1705,
1707, 1709, 1712-1716, 1720, 1722, 1725, 1727, 1730, 1732, 1735-1738, 1741-1743, 1746,
1750-1755, 1764, 1767, 1770, 1774-1776, 1781-1784, 1793, 1796, 1802, 1809-1811, 1815, 1820,
1822, 1825, 1827, 1829-1830, 1837, 1839-1841, 1843-1845, 1847, 1849-1851, 1853-1857,
1860-1863, 1866-1867, 1869-1871, 1873-1874, 1876-1877, 1879, 1884-1887, 1889-1890, 1892,
1896-1897, 1899, 1901, 1904-1905, 1909-1913, 1915-1916, 1918, 1920, 1922, 1928, 1930-1931,
1936, 1941, 1944, 1949, 1953, 1957, 1959, 1973, 1978, 1980, 1988, 1994, 1996, 1998, 2007-2010,
2012-2014, 2017, 2021, 2025, 2032, 2036, 2045-2046, 2053-2054, 2057, 2060, 2062, 2064,
2066-2067, 2071, 2085, 2088-2089, 2091, 2097, 2107, 2115, 2153, 2159, 2161, 2168, 2171-2172,
2176, 2184, 2192, 2195, 2198-2199, 2201, 2203, 2205-2206, 2210, 2221, 2227, 2235, 2237, 2239,
2241, 2248, 2256, 2258, 2264-2265, 2267, 2269-2270, 2273, 2275, 2280-2281, 2284, 2297, 2299,
2301, 2303, 2306-2307, 2310, 2313, 2318, 2320, 2322, 2324, 2333-2334, 2338, 2346, 2348-2350,
2352, 2354-2356, 2361, 2363, 2369, 2371, 2375, 2380, 2394, 2398, 2405-2406, 2416, 2418, 2424,
2429-2431, 2438, 2442, 2447, 2452, 2454, 2459, 2461, 2465-2466, 2468, 2476, 2481-2482, 2487,
2517, 2539, 2541, 2554, 2556, 2559, 2562-2564, 2567, 2569, 2575, 2585, 2591, 2593, 2595,
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 13, 2023
737-22A1399 RB
5 of 45

### Page 6

2598, 2600-2602, 2604, 2608, 2610-2613, 2617, 2619-2620, 2622-2623, 2625-2629, 2635-2636,
2639, 2643-2645, 2651, 2653, 2667-2668, 2670, 2677, 2679, 2687, 2689-2690, 2695-2697, 2699,
2702-2703, 2709, 2711, 2713-2717, 2741-2742, 2746-2747, 2749, 2753, 2756, 2759, 2762, 2765,
2773, 2775, 2785, 2794, 2801-2802, 2827, 2829-2831, 2837, 2839, 2844, 2847, 2854, 2873,
2878-2879, 2901, 2915, 2917-2918, 2930-2932, 2957, 2959, 2962, 2968, 2977-2978, 2997, 3007,
3009, 3016, 3021 in 4 Group(s). Where the effectivity is presented with hyphens between line
numbers, the airplane applicability means "through" and "inclusive", e.g. line numbers 1-9 means
line numbers 1 through 9 inclusive.
The Variable Numbers and Group Information for the applicable airplanes is given below.
DESCRIPTIONCONFIGURATIONGROUP
Airplanes with different wiring configuration.-1
Airplanes with different wiring configuration.-2
Airplanes with different wiring configuration.-3
Airplanes with different wiring configuration.-4
Airplane Models:
737-300, 737-400
GroupVariable Number
4PJ301 - PJ302
4PJ811
4PJ816 - PJ817
2PM382 - PM385
2PM387
2PM389 - PM392
2PM395 - PM396
2PM398
2PM401
2PM404 - PM405
2PM407 - PM414
2PM416
2PM543
2PM545 - PM546
2PM548 - PM549
GroupVariable Number
4PM551 - PM557
4PM560 - PM562
4PM564
1PP003
1PP006
1PP010
1PP013
1PP017 - PP018
1PP022 - PP023
1PP028
1PP034
1PP036
1PP040 - PP041
1PP043
1PP047
GroupVariable Number
1PP049 - PP051
1PP053
1PP114
1PP124
1PP132
1PP136 - PP137
1PP156 - PP157
1PP159 - PP160
1PP169
1PP192
4PP198
1PP221
1PP232
1PP239
1PP242
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 13, 2023
737-22A1399 RB
6 of 45
REQUIREMENTS BULLETIN 737-22A1399
ALERTALERT

### Page 7

GroupVariable Number
1PP301 - PP302
1PP305
1PP352
1PP376 - PP377
1PP381
1PP384
4PP392
1PP401
1PP406 - PP407
1PP410
1PP413 - PP414
1PP420
1PP427 - PP430
1PP433 - PP434
1PP436
1PP440
1PP472
1PP474
2PP503
2PP505 - PP506
2PP508
2PP510
1PP521 - PP522
1PP631
1PP634
1PP673
1PP679
1PP682 - PP683
1PP685
1PP691
1PP693 - PP694
1PP702 - PP703
1PP711
GroupVariable Number
1PP728 - PP729
1PP771
1PP774
1PP776
1PP802
4PP805 - PP807
1PP823
1PP825
1PP827
2PP832 - PP834
2PP841
2PP845 - PP848
2PP852
2PP862
2PP865
2PP868
2PP874 - PP877
2PP892
2PP894
2PP896 - PP899
2PP901 - PP902
2PP904
2PP917
2PP919
2PP921
2PP925
2PP928 - PP930
2PP932
2PP936
2PP947 - PP948
2PP951 - PP952
2PP963 - PP966
2PP983
GroupVariable Number
2PP986 - PP987
2PP991
2PQ002 - PQ004
2PQ006 - PQ011
2PQ026
2PQ028
2PQ033
2PQ035
2PQ053
2PQ057
2PQ086 - PQ092
2PQ113
2PQ115
2PQ117 - PQ120
2PQ123 - PQ124
2PQ127
2PQ136
2PQ140 - PQ141
2PQ143
2PQ145
2PQ150
2PQ155 - PQ156
2PQ160 - PQ163
2PQ168 - PQ169
2PQ172 - PQ173
2PQ176
2PQ178
2PQ181 - PQ182
2PQ186 - PQ187
2PQ189 - PQ190
2PQ193
2PQ195 - PQ199
2PQ201
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 13, 2023
737-22A1399 RB
7 of 45
REQUIREMENTS BULLETIN 737-22A1399
ALERTALERT

### Page 8

GroupVariable Number
4PQ221 - PQ225
4PQ228
3PQ231
3PQ233
3PQ236 - PQ237
3PQ242 - PQ243
4PQ252
4PQ254
4PQ258 - PQ259
4PQ262 - PQ264
4PQ281
4PQ286
4PQ288 - PQ289
4PQ293
4PQ295
4PQ297 - PQ299
4PQ301
4PQ303 - PQ305
4PQ307
4PQ331 - PQ332
4PQ448
4PQ451
4PQ454
4PQ481
4PQ487
4PQ491
4PQ493
2PS601 - PS603
2PS606 - PS611
2PS618
2PS620 - PS629
2PS631
2PS636 - PS638
GroupVariable Number
2PS641 - PS644
4PS653 - PS654
4PS666 - PS668
1PS751
1PS766 - PS774
1PS776 - PS789
1PS791 - PS792
1PS796
2PS841 - PS844
2PS846
2PS851 - PS852
2PS856
2PS871 - PS874
2PS896 - PS897
1PS902
1PS904
1PS935 - PS936
1PS938 - PS941
4PV001 - PV003
4PV009
4PV012 - PV013
4PV015 - PV020
4PV023
4PV031 - PV036
4PV039
4PV041 - PV043
4PV047
4PV053
4PW001 - PW002
4PW005
4PW007
4PW011
4PW013
GroupVariable Number
4PW019
4PW024
4PW028 - PW029
4PW031
4PW033
4PW035 - PW036
4PW039 - PW041
4PW043
4PW045 - PW054
4PW063
4PW065 - PW066
4PW068
4PW072
4PW091
4PW093 - PW094
4PW101
4PW106
4PW111 - PW117
4PW161 - PW162
4PW164
4PW166 - PW171
4PW233 - PW240
4PW261 - PW268
4PW271 - PW272
4PW274
4PW276
4PW281 - PW288
4PW290 - PW291
4PW293
4PW296
4PW502 - PW504
4PW511 - PW522
4PW524 - PW527
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 13, 2023
737-22A1399 RB
8 of 45
REQUIREMENTS BULLETIN 737-22A1399
ALERTALERT

### Page 9

GroupVariable Number
4PW529 - PW533
4PW535 - PW537
4PW539 - PW550
4PW557
4PW561
GroupVariable Number
4PW563 - PW564
4PW572 - PW573
4PW591
4PW593 - PW596
4PW612
GroupVariable Number
4PW616
4PW618 - PW619
4PW621 - PW622
4PW661 - PW662
--
B. Spares Affected
None.
2. CONCURRENT REQUIREMENTS
None.
3. COMPLIANCE
The Federal Aviation Administration (FAA) will possibly release an additional Airworthiness Directive related
to Requirements Bulletin 737-22A1399 RB. The Airworthiness Directive will make the compliance tasks
and times given in Requirements Bulletin 737-22A1399 RB mandatory.
FAA AD 2000-23-34 is related to Requirements Bulletin 737-22A1399 RB. The effective date of AD
2000-23-34 is January 8, 2001.
Accomplish the required action(s), based on the applicable condition(s) in Table(s) 1, in accordance with
Accomplishment Instructions.
When more than one OPTION is given for a CONDITION, do only one of the OPTION numbers. When
more than one ACTION is given for a CONDITION or an OPTION, do all of the ACTION numbers for that
CONDITION or OPTION.
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 13, 2023
737-22A1399 RB
9 of 45
REQUIREMENTS BULLETIN 737-22A1399
ALERTALERT

### Page 10

Table 1: Mechanical Aileron Force Limiter Removal, Housing Assembly Installation and Flight Control
Computers Replacement
Repeat In-
terval (Not
to Exceed)
Boeing Recommended
Compliance Time
(Whichever Occurs first)
ActionCondition
-Within 21 months
after the Original
Issue date of Re-
quirements Bulletin
737-22A1399 RB.
Within 4,680
flight hours af-
ter the Original
Issue date of
Requirements
Bulletin 737-
22A1399 RB.
ACTION 1: In the flight compart-
ment, in the P18-1 panel, deac-
tivate one circuit breaker and
change wire bundle W029.
All Airplanes
ACTION 2: In the lower nose
compartment, remove the Me-
chanical Aileron Force Limiter
(MAFL), install a housing as-
sembly and change wire bundle
W369.
ACTION 3: Change wire bun-
dles W011 and W069.
ACTION 4: Do an inspection or
a maintenance records check
of the two existing FCCs for
part number 4051600-914
(Boeing part number 10-62038-
4).
Install the kept FCCs and do
specified tests and make sure
the tests are passed. If any test
fails, do applicable corrective
action and repeat the test until
the test passes.
CONDITION 1: PART
NUMBER 4051600-914
(BOEING PART NUMBER
10-62038-4) FOUND.
Install new FCCs, part number
4051600-914 (Boeing part
number 10-62038-4) and do
specified tests and make sure
the tests are passed. If any test
fails, do applicable corrective
action and repeat the test until
the test passes.
CONDITION 2 : PART
NUMBER 4051600-914
(BOEING PART NUMBER
10-62038-4) NOT FOUND.
4. APPROVAL
This service bulletin was examined by the Boeing Company Organization Designation Authorization (ODA).
The changes specified in this service bulletin comply with the applicable regulations and are FAA approved,
as well as European Union Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for
all EASA/JAA approved airplanes listed in the service bulletin effectivity. This service bulletin and its approval
were based on the airplane in its original Boeing delivery configuration or as modified by other approved
Boeing changes.
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 13, 2023
737-22A1399 RB
10 of 45
REQUIREMENTS BULLETIN 737-22A1399
ALERTALERT

### Page 11

If an airplane has a non-Boeing modification or repair that affects a component or system also affected by
this requirements bulletin, the operator is responsible for obtaining appropriate regulatory agency approval
before incorporating this requirements bulletin.
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 13, 2023
737-22A1399 RB
11 of 45
REQUIREMENTS BULLETIN 737-22A1399
ALERTALERT

### Page 12

Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 13, 2023
737-22A1399 RB
12 of 45
REQUIREMENTS BULLETIN 737-22A1399
ALERTALERT
BLANK PAGE

### Page 13

5.    ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL INFORMATION
NOTE: 1. This is an Enhanced Required for Compliance document. There will be a separate
Service Bulletin (SB) and a separate Requirements Bulletin (RB). If an RB is mandated
by an Airworthiness Directive (AD), then all applicable requirements specified in the
RB must be done. For the related SB, some locations are marked RC Start and RC
End to identify the requirements that are restated from the RB. For the related SB,
the areas between RC Start and RC End, including sub-steps and any figures
identified between RC Start and RC End, must be done to comply with the AD.
Therefore, an Alternative Method of Compliance (AMOC) is required for any deviations
to steps between RC Start and RC End, including substeps and identified figures.
For the related SB, the steps not between RC Start and RC End may be deviated
from using accepted methods in accordance with the operator's maintenance or
inspection program without obtaining approval of an AMOC; this is provided that the
steps between RC Start and RC End, including sub-steps and identified figures, can
still be done as specified, and the airplane can be put back in an airworthy condition.
Figures not required for compliance are omitted from the RB.
2. This is an Enhanced Required for Compliance document. The Boeing processes
used to create the Service Bulletin (SB) and the Requirements Bulletin (RB) ensure
that the information between "RC Start" and "RC End" in the SB are identical to the
information in the same sections (Compliance, Work Instructions...) of the RB which
the SB refers to as the related document.
3. The compliance times for the actions in WORK INSTRUCTIONS are in Compliance.
4. Unless shown differently, these dimensions and tolerances are used:
– Linear dimensions are in inches
– Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus
or minus 0.03 inch
– Tolerance on rivet and bolt edge margin is plus or minus 0.05 inch
– Angular tolerance is plus or minus 2 degrees
– Hole dimensions for standard solid rivets and fasteners are in Structural Repair
Manual (SRM) Chapter 51
– Torque Values:
— Values for structural fasteners are given in 737 Structural Repair Manual,
Chapter 51.
— Values for airframe maintenance tasks are included in Chapter 20 of 737
Aircraft Maintenance Manual (AMM).
— Values for electrical maintenance tasks are included in Chapter 20 of
Standard Wiring Practices Manual (SWPM).
— Values for engine maintenance tasks are included in Chapter 70 of 737
Aircraft Maintenance Manual (AMM).
— Non-standard torque values for maintenance tasks are included in the
applicable installation step.
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 13, 2023
737-22A1399 RB
13 of 45
REQUIREMENTS BULLETIN 737-22A1399
ALERTALERT

### Page 14

5. These work instructions refer to procedures included in other Boeing documents.
When the words "refer to" are used and the operator has an accepted alternative
procedure, the accepted alternative procedure can be used. When the words "in
accordance with" are included in the instruction, the procedure in the Boeing document
must be used.
6. Use the approved fastener, process and material substitutions in accordance with
SRM Chapter 51.
7. Refer to the SWPM 20-10-11 and SWPM 20-10-12 for the wire installation procedures,
and SWPM 20-10-19 for the wire separation requirements, as accepted procedures.
8. The necessary conditions for selection of clamp type and size are included in SWPM
20-10-12. If any wire bundle support clamp specified in this service bulletin does not
make a correct fit on the wire bundle, refer to SWPM 20-10-12 as an accepted
procedure to select a clamp that fits correctly.
9. If the length of any fastener specified in this service bulletin does not meet installation
standards given in SRM Chapter 51, then a fastener of the same specification, or
an approved substitute, with a length which meets the installation standards given
in SRM Chapter 51 may be used. In addition, washers may be installed for fastener
grip length in accordance with SRM Chapter 51. Refer to SOPM 20-50-01 for alternate
full threaded fasteners (screws) needed for installation in this service bulletin.
10. When more than one OPTION is given for a CONDITION, do only one of the OPTION
numbers. When more than one ACTION is given for a CONDITION or an OPTION,
do all of the ACTION numbers for that CONDITION or OPTION.
11. If it is necessary to remove more parts for access, you can remove those parts. If
you can get access without removing identified parts, it is not necessary to remove
all of the identified parts. Jacking and shoring limitations must be observed.
12. Where the work instructions include installation of a kept part, a new or serviceable
part with the same part number can be installed as an alternative to the kept part.
B. WORK INSTRUCTIONS
Actions Required for Compliance
1. Requirements.
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 13, 2023
737-22A1399 RB
14 of 45
REQUIREMENTS BULLETIN 737-22A1399
ALERTALERT

### Page 15

Group 1:
Table 1: Mechanical Aileron Force Limiter Removal, Housing Assembly Installation and Flight Control
Computers Replacement
Refer to the listed proce-
dures in SB 737-22A1399
Original Issue or later ap-
proved revisions as an ac-
cepted procedure.
Method of
Compliance
ActionCondition
PART 1: Open Access-ACTION 1: In the flight compart-
ment, in the P18-1 panel, deacti-
vate one circuit breaker and
change wire bundle W029.
All Airplanes
-FIGURE 1
FIGURE 2
-FIGURE 3ACTION 2: In the lower nose
compartment, remove the Mechan-
ical Aileron Force Limiter (MAFL),
install a housing assembly and
change wire bundle W369.
FIGURE 4
FIGURE 5
-FIGURE 7, FIGURE 8,
and FIGURE 9
ACTION 3: Change wire bundles
W011 and W069.
PART 2: Flight Control Com-
puter Remove And Keep
-ACTION 4: Do an inspection or a
maintenance records check of the
two existing FCCs for part number
4051600-914 (Boeing part number
10-62038-4).
PART 3: Flight Control Com-
puter Install Kept
-Install the kept FCCs and do
specified tests and make sure the
tests are passed. If any test fails,
do applicable corrective action and
repeat the test until the test pass-
es.
CONDITION 1:
PART NUMBER
4051600-914 (BOE-
ING PART NUM-
BER 10-62038-4)
FOUND.
-APPENDIX C
PART 5: Close Access-
PART 4: Flight Control Com-
puter Install New
-Install new FCCs, part number
4051600-914 (Boeing part number
10-62038-4) and do specified tests
and make sure the tests are
passed. If any test fails, do applica-
ble corrective action and repeat
the test until the test passes.
CONDITION 2:
PART NUMBER
4051600-914 (BOE-
ING PART NUM-
BER 10-62038-4)
NOT FOUND.
-APPENDIX C
PART 5: Close Access-
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 13, 2023
737-22A1399 RB
15 of 45
REQUIREMENTS BULLETIN 737-22A1399
ALERTALERT

### Page 16

Group 2:
Table 1: Mechanical Aileron Force Limiter Removal, Housing Assembly Installation and Flight Control
Computers Replacement
Refer to the listed proce-
dures in SB 737-22A1399
Original Issue or later ap-
proved revisions as an ac-
cepted procedure.
Method of
Compliance
ActionCondition
PART 1: Open Access-ACTION 1: In the flight compart-
ment, in the P18-1 panel, deacti-
vate one circuit breaker and
change wire bundle W029.
All Airplanes
-FIGURE 1
FIGURE 2
-FIGURE 3ACTION 2: In the lower nose
compartment, remove the Mechan-
ical Aileron Force Limiter (MAFL),
install a housing assembly and
change wire bundle W369.
FIGURE 4
FIGURE 5
-FIGURE 7, FIGURE
10, and FIGURE 11
ACTION 3: Change wire bundles
W011 and W069.
PART 2: Flight Control Com-
puter Remove And Keep
-ACTION 4: Do an inspection or a
maintenance records check of the
two existing FCCs for part number
4051600-914 (Boeing part number
10-62038-4).
PART 3: Flight Control Com-
puter Install Kept
-Install the kept FCCs and do
specified tests and make sure the
tests are passed. If any test fails,
do applicable corrective action and
repeat the test until the test pass-
es.
CONDITION 1:
PART NUMBER
4051600-914 (BOE-
ING PART NUM-
BER 10-62038-4)
FOUND.
-APPENDIX C
PART 5: Close Access-
PART 4: Flight Control Com-
puter Install New
-Install new FCCs, part number
4051600-914 (Boeing part number
10-62038-4) and do specified tests
and make sure the tests are
passed. If any test fails, do applica-
ble corrective action and repeat
the test until the test passes.
CONDITION 2:
PART NUMBER
4051600-914 (BOE-
ING PART NUM-
BER 10-62038-4)
NOT FOUND.
-APPENDIX C
PART 5: Close Access-
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 13, 2023
737-22A1399 RB
16 of 45
REQUIREMENTS BULLETIN 737-22A1399
ALERTALERT

### Page 17

Group 3:
Table 1: Mechanical Aileron Force Limiter Removal, Housing Assembly Installation and Flight Control
Computers Replacement
Refer to the listed proce-
dures in SB 737-22A1399
Original Issue or later ap-
proved revisions as an ac-
cepted procedure.
Method of
Compliance
ActionCondition
PART 1: Open Access-ACTION 1: In the flight compart-
ment, in the P18-1 panel, deacti-
vate one circuit breaker and
change wire bundle W029.
All Airplanes
-FIGURE 1
FIGURE 2
-FIGURE 3ACTION 2: In the lower nose
compartment, remove the Mechan-
ical Aileron Force Limiter (MAFL),
install a housing assembly and
change wire bundle W369.
FIGURE 4
FIGURE 5
-FIGURE 7, FIGURE
12, and FIGURE 13
ACTION 3: Change wire bundles
W011 and W069.
PART 2: Flight Control Com-
puter Remove And Keep
-ACTION 4: Do an inspection or a
maintenance records check of the
two existing FCCs for part number
4051600-914 (Boeing part number
10-62038-4).
PART 3: Flight Control Com-
puter Install Kept
-Install the kept FCCs and do
specified tests and make sure the
tests are passed. If any test fails,
do applicable corrective action and
repeat the test until the test pass-
es.
CONDITION 1:
PART NUMBER
4051600-914 (BOE-
ING PART NUM-
BER 10-62038-4)
FOUND.
-APPENDIX C
PART 5: Close Access-
PART 4: Flight Control Com-
puter Install New
-Install new FCCs, part number
4051600-914 (Boeing part number
10-62038-4) and do specified tests
and make sure the tests are
passed. If any test fails, do applica-
ble corrective action and repeat
the test until the test passes.
CONDITION 2:
PART NUMBER
4051600-914 (BOE-
ING PART NUM-
BER 10-62038-4)
NOT FOUND.
-APPENDIX C
PART 5: Close Access-
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 13, 2023
737-22A1399 RB
17 of 45
REQUIREMENTS BULLETIN 737-22A1399
ALERTALERT

### Page 18

Group 4:
Table 1: Mechanical Aileron Force Limiter Removal, Housing Assembly Installation and Flight Control
Computers Replacement
Refer to the listed proce-
dures in SB 737-22A1399
Original Issue or later ap-
proved revisions as an ac-
cepted procedure.
Method of
Compliance
ActionCondition
PART 1: Open Access-ACTION 1: In the flight compart-
ment, in the P18-1 panel, deacti-
vate one circuit breaker and
change wire bundle W029.
All Airplanes
-FIGURE 1
FIGURE 2
-FIGURE 3ACTION 2: In the lower nose
compartment, remove the Mechan-
ical Aileron Force Limiter (MAFL),
install a housing assembly and
change wire bundle W369.
FIGURE 4
FIGURE 5
-FIGURE 7, FIGURE
14, and FIGURE 15
ACTION 3: Change wire bundles
W011 and W069.
PART 2: Flight Control Com-
puter Remove And Keep
-ACTION 4: Do an inspection or a
maintenance records check of the
two existing FCCs for part number
4051600-914 (Boeing part number
10-62038-4).
PART 3: Flight Control Com-
puter Install Kept
-Install the kept FCCs and do
specified tests and make sure the
tests are passed. If any test fails,
do applicable corrective action and
repeat the test until the test pass-
es.
CONDITION 1:
PART NUMBER
4051600-914 (BOE-
ING PART NUM-
BER 10-62038-4)
FOUND.
-APPENDIX C
PART 5: Close Access-
PART 4: Flight Control Com-
puter Install New
-Install new FCCs, part number
4051600-914 (Boeing part number
10-62038-4) and do specified tests
and make sure the tests are
passed. If any test fails, do applica-
ble corrective action and repeat
the test until the test passes.
CONDITION 2:
PART NUMBER
4051600-914 (BOE-
ING PART NUM-
BER 10-62038-4)
NOT FOUND.
-APPENDIX C
PART 5: Close Access-
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 13, 2023
737-22A1399 RB
18 of 45
REQUIREMENTS BULLETIN 737-22A1399
ALERTALERT

### Page 19 (OCR)

REQUIREMENTS BULLETIN 737-22A1399
ALERT  ALERT
• BEFORE
1 AFTER
FLIGHT COMPARTMENT
AUTO FLIGHT CONTROL  AFDS
AFDS  MCP  F THROTTLE  AUTO  • DAMPER  YAW  FORCE  AIL
DC  AC  DC  LIMITER
5  5  3  3  5  5
C1044  C720  C721  C285  C286  C723
P18-1 PANEL
(BEFORE)
AUTO FLIGHT CONTROL
AFDS  MCP  F THROTTLEC  AUTO  DAMPER  YAW
DC  DC
5  5  5  5
C1044  C720  C721  C285  C286  (INOP)
P18-1 PANEL
(AFTER)
3019756
FIGURE 1: P18-1 PANEL - CIRCUIT BREAKER C723 - DEACTIVATE
(SHEET 1 OF 2)
Original Issue: April 13, 2023
Export Controlled ECCN: 9E991  737-22A1399 RB
Copyright © Unpublished Work - See page 1 for details.  19 of 45

### Page 20

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
More DataQtyIdentificationNameTaskStep
1-MARKERRemove1
110237-1COLLARInstall (New)2
(a)1BAC27DCC2154MARKERInstall (New)3
(a)1BAC27DCC3073MARKERInstall (New)4
(a) Refer to SOPM 20-50-05 as an accepted procedure.
FIGURE 1: P18-1 PANEL - CIRCUIT BREAKER C723 - DEACTIVATE
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 13, 2023
737-22A1399 RB
20 of 45
REQUIREMENTS BULLETIN 737-22A1399
ALERTALERT

### Page 21

REFERENCE: 737-300/400/500 WDM 22-11-11
Use wire kit 61-74519-101.
The find numbers (No.) shown below agree with the find number symbol in the figure.
More DataQtyIdentificationName
Find
No.
(a)161-74519-10101THERMOFIT SLEEVE -
YELLOW - 0.125 IN I.D.
1
(b)1M23053/12-229-CPOLYTETRAFLUO-
ROETHYLENE, HEAT
SHRINKABLE SLEEVE
2
(a) Refer to SWPM 20-30-16 as an accepted procedure.
(b) Refer to SWPM 20-10-14 as an accepted procedure.
FIGURE 2: P18-1 PANEL - WIRE BUNDLE W029 - WIRING CHANGE
(SHEET 1 OF 1)
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 13, 2023
737-22A1399 RB
21 of 45
REQUIREMENTS BULLETIN 737-22A1399
ALERTALERT

### Page 22 (OCR)

REQUIREMENTS BULLETIN 737-22A1399
ALERT  ALERT
CONTROL
WHEEL
CAPTAIN'S
CONTROL COLUMN
FLIGHT
COMPARTMENT
FLOOR LEVEL
3019759
FIGURE 3: LOWER NOSE COMPARTMENT - MECHANICAL AILERON FORCE LIMITER (MAFL) - REMOVAL
(SHEET 1 OF 2)
Original Issue: April 13, 2023
_ Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.

### Page 23

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
More DataQtyIdentificationNameTaskStep
(a)1-NUTRemove / Keep1
(a)2-WASHERRemove / Keep
(a)1-BOLTRemove / Keep
(a)2-NUTRemove / Keep2
(a)4-WASHERRemove / Keep
(a)2-BOLTRemove / Keep
(a)1-LIMIT MECHANISMRemove3
(a) Refer to 737-300/400/500 AMM 22-11-13 as an accepted procedure.
FIGURE 3: LOWER NOSE COMPARTMENT - MECHANICAL AILERON FORCE LIMITER (MAFL) - REMOVAL
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 13, 2023
737-22A1399 RB
23 of 45
REQUIREMENTS BULLETIN 737-22A1399
ALERTALERT

### Page 24 (OCR)

REQUIREMENTS BULLETIN 737-22A1399
ALERT  ALERT
CONTROL
WHEEL
CAPTAIN'S
CONTROL COLUMN
FLIGHT
COMPARTMENT-
FLOOR LEVEL
3019773
FIGURE 4: LOWER NOSE COMPARTMENT - MAFL HOUSING ASSEMBLY - INSTALLATION
(SHEET 1 OF 2)
Original Issue: April 13, 2023
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.

### Page 25

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
More DataQtyIdentificationNameTaskStep
169-77930-1HOUSING ASSYInstall (New)1
1NAS6604-16BOLTInstall (Kept)2
2NAS960JD416LWASHERInstall (Kept)
1BACN10JC4NUTInstall (Kept)
2NAS6604-7BOLTInstall (Kept)3
4NAS960JD416LWASHERInstall (Kept)
2BACN10JC4NUTInstall (Kept)
FIGURE 4: LOWER NOSE COMPARTMENT - MAFL HOUSING ASSEMBLY - INSTALLATION
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 13, 2023
737-22A1399 RB
25 of 45
REQUIREMENTS BULLETIN 737-22A1399
ALERTALERT

### Page 26 (OCR)

REQUIREMENTS BULLETIN 737-22A1399
ALERT  ALERT
W369
• (8 LOCATIONS)
019-20 -{
5-  020-20 -
вини  022-20 -→
024-20 -
009-20 -  →
10-HHHHHH 026-20 HHHO/' GD987-AC
11-  - 010-20 -  →
021-20
025-20
D1785
→ (7 LOCATIONS)
H 052-20 HHHO/' GD975-DC
005-20
054-20
9  066-20
10-  053-20
13 -  029-20
031-20
15  - 036-20 -
D443
M401 AILERON FORCE LIMITER
+ DELETED WIRE OR FORMER ROUTING  ADDED WIRE OR NEW ROUTING  >  • FIND NUMBER  - EXISTING WIRE  3019774
REFERENCE: 737-300/400/500 WDM 22-11-71, 737-300/400/500 WDM 22-11-72
FIGURE 5: LOWER NOSE COMPARTMENT - WIRE BUNDLE W369 - WIRING CHANGE
(SHEET 1 OF 2)
Original Issue: April 13, 2023
737-22A1399 RB
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.  26 of 45

### Page 27

Use wire kit 61-74519-102.
The find numbers (No.) shown below agree with the find number symbol in the figure.
More DataQtyIdentificationName
Find
No.
(a)1561-74519-10101THERMOFIT SLEEVE -
YELLOW - 0.125 IN I.D.
1
(a) Refer to SWPM 20-30-16 as an accepted procedure.
FIGURE 5: LOWER NOSE COMPARTMENT - WIRE BUNDLE W369 - WIRING CHANGE
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 13, 2023
737-22A1399 RB
27 of 45
REQUIREMENTS BULLETIN 737-22A1399
ALERTALERT

### Page 28 (OCR)

REQUIREMENTS BULLETIN 737-22A1399
ALERT  ALERT
MAIN EQUIPMENT CENTER  GDX20-DC  TO
D1795B
D1791A
TO
D1661B
TO
D1657A
GDX34
W011
SP2169
SPLICE AREA
GDX6-DC-  W069
GDX1
E1-3 ELECTRONICS SHELF  3019793
TYPICAL
FIGURE 7: E1-3 ELECTRONICS SHELF - WIRE BUNDLES W011 AND W069 - WIRE ROUTING
(SHEET 1 OF 1)
Original Issue: April 13, 2023
737-22A1399 RB
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.  28 of 45

### Page 29 (OCR)

REQUIREMENTS BULLETIN 737-22A1399
ALERT  ALERT
This Figure applies only to: Group 1.
W069
36
37
D2209B
M1194 AFC ACCESSORY
UNIT
1411174-053-20-71  61
1H4 052-20+4  64
D1659B
GDX6-DC I|  592-20  56
D1657A
SP2259  7061-20  25
SP2257  -062-20  28
W011
W011  → SP2169  594-20
50
SP2255 //
D1661B
M923 FLIGHT CONTROL
CMPTR "B"
E1-3 ELECTRONIC SHELF
- ADDED WIRE OR NEW ROUTING
+ DELETED WIRE OR FORMER ROUTING
- EXISTING WIRE
FIND NUMBER  3019875
FLAG NOTE
FIGURE 8: E1-3 ELECTRONICS SHELF - WIRE BUNDLE W069 - WIRING CHANGE
(SHEET 1 OF 2)
Original Issue: April 13, 2023
Export Controlled ECCN: 9E991  737-22A1399 RB
Copyright © Unpublished Work - See page 1 for details.  29 of 45

### Page 30

REFERENCE: 737-300/400/500 WDM 22-11-72, 737-300/400/500 WDM 22-13-12
Use wire kit 61-74519-103.
The find numbers (No.) shown below agree with the find number symbol in the figure.
More DataQtyIdentificationName
Find
No.
(a)1BACT12AR204TERMINAL1
(b)2031-9134-004CONTACT2
(c)1D-436-59SPLICE - SEALING
SLEEVE
3
(c)161-74519-10301WIRE, SLEEVE4
(d)(e)161-74519-103WWIRE LIST5
(d)-61-74519-2003LACING TAPE - YELLOW
(d)-61-74519-2001LACING TAPE - ORANGE
(a) Refer to SWPM 20-30-11 and SWPM 20-20-10 as accepted procedures.
(b) Refer to SWPM 20-71-11 as an accepted procedure.
(c) Refer to SWPM 20-30-16 as an accepted procedure.
(d) Refer to SWPM 20-10-11 as an accepted procedure.
(e) Refer to SWPM 20-10-12 as an accepted procedure.
NOTEFlag Note
Wire requires yellow color coding for channel B separation.A
Wire requires orange color coding for channel F separation.B
Reinstall wires W011-90-20, W011-105-20 and W069-071-20 to splice SP2169.C
FIGURE 8: E1-3 ELECTRONICS SHELF - WIRE BUNDLE W069 - WIRING CHANGE
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 13, 2023
737-22A1399 RB
30 of 45
REQUIREMENTS BULLETIN 737-22A1399
ALERTALERT

### Page 31 (OCR)

REQUIREMENTS BULLETIN 737-22A1399
ALERT  ALERT
This Figure applies only to: Group 1.
W011
W101  20
22
D5945J  P
4H 061-20 H  110
4## 058-20+4  21
36
37
D2209A
M1194 AFC ACCESSORY
UNIT
H074-20+4
+ 075-20+  64
D1793B
10
52  GDX20-DC 1IC  -8222-20  56
9
D1791A
19  ++++ 056-20 +  SM114
21 H4+ 051-20+  SM115
22  + 077-20 +  SP255  → W069
25 HHH+ 078-20 +  SP2553  - W069
W369  7 +44 062-20 +  SM105
22  H 079-20+44  4A SP2555  W069
53  + 063-20+4  25
54 144 064-20+44  28
- W069
SP2169  8223-20
20  50
29 + 082-20 + SP2557  36  +H+ 081-20 H  SP2559  _ W069  D1795B
4HH 080-20 HH4  M924 FLIGHT CONTROL
D4075J  CMPTR "A"
E1-3 ELECTRONIC SHELF
ADDED WIRE OR NEW ROUTING
PAT DELETED WIRE OR FORMER ROUTING
EXISTING WIRE
FIND NUMBER  3019877
FLAG NOTE
FIGURE 9: E1-3 ELECTRONICS SHELF - WIRE BUNDLE W011 - WIRING CHANGE
(SHEET 1 OF 2)
Original Issue: April 13, 2023
Export Controlled ECCN: 9E991  737-22A1399 RB
Copyright © Unpublished Work - See page 1 for details.  31 of 45

### Page 32

REFERENCE: 737-300/400/500 WDM 22-11-11, 737-300/400/500 WDM 22-11-71, 737-300/400/500 WDM
22-11-72, 737-300/400/500 WDM 22-13-12
Use wire kit 61-74519-104.
The find numbers (No.) shown below agree with the find number symbol in the figure.
More DataQtyIdentificationName
Find
No.
(a)1BACT12AR204TERMINAL1
(b)2031-9134-004CONTACT2
(c)1D-436-59SPLICE - SEALING
SLEEVE
3
(c)161-74519-10301WIRE, SLEEVE4
(d)(e)161-74519-104WWIRE LIST5
(d)-61-74519-2002LACING TAPE - RED
(d)-61-74519-2001LACING TAPE - ORANGE
(a) Refer to SWPM 20-30-11 and SWPM 20-20-10 as accepted procedures.
(b) Refer to SWPM 20-71-11 as an accepted procedure.
(c) Refer to SWPM 20-30-16 as an accepted procedure.
(d) Refer to SWPM 20-10-11 as an accepted procedure.
(e) Refer to SWPM 20-10-12 as an accepted procedure.
NOTEFlag Note
Wire requires red color coding for channel B separation.A
Wire requires orange color coding for channel F separation.B
Reinstall wires W011-90-20, W011-105-20 and W069-071-20 to splice SP2169.C
FIGURE 9: E1-3 ELECTRONICS SHELF - WIRE BUNDLE W011 - WIRING CHANGE
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 13, 2023
737-22A1399 RB
32 of 45
REQUIREMENTS BULLETIN 737-22A1399
ALERTALERT

### Page 33 (OCR)

REQUIREMENTS BULLETIN 737-22A1399
ALERT  ALERT
This Figure applies only to: Group 2.
W069
37
D2209B
M1194 AFC ACCESSORY
UNIT
< 053-20 HA  61
Хунн  4052-20+  64
D1659B
GDX6-DC 'C  592-20  56
D1657A
- - W011
W011  → SP2169-  594-20  50
W011 - -
D1661B
M923 FLIGHT CONTROL
CMPTR "B"
E1-3 ELECTRONIC SHELF
• ADDED WIRE OR NEW ROUTING
+ DELETED WIRE OR FORMER ROUTING
EXISTING WIRE
- FIND NUMBER  3019878
→ FLAG NOTE
REFERENCE: 737-300/400/500 WDM 22-11-72, 737-300/400/500 WDM 22-13-12
Use wire kit 61-74519-105.
FIGURE 10: E1-3 ELECTRONICS SHELF - WIRE BUNDLE W069 - WIRING CHANGE
(SHEET 1 OF 2)
Original Issue: April 13, 2023
Export Controlled ECCN: 9E991  737-22A1399 RB
Copyright © Unpublished Work - See page 1 for details.  33 of 45

### Page 34

The find numbers (No.) shown below agree with the find number symbol in the figure.
More DataQtyIdentificationName
Find
No.
(a)1BACT12AR204TERMINAL1
(b)2031-9134-004CONTACT2
(c)1D-436-59SPLICE - SEALING
SLEEVE
3
(c)161-74519-10301WIRE, SLEEVE4
(d)(e)161-74519-105WWIRE LIST5
(d)-61-74519-2003LACING TAPE - YELLOW
(d)-61-74519-2001LACING TAPE - ORANGE
(a) Refer to SWPM 20-30-11 and SWPM 20-20-10 as accepted procedures.
(b) Refer to SWPM 20-71-11 as an accepted procedure.
(c) Refer to SWPM 20-30-16 as an accepted procedure.
(d) Refer to SWPM 20-10-11 as an accepted procedure.
(e) Refer to SWPM 20-10-12 as an accepted procedure.
NOTEFlag Note
Wire requires yellow color coding for channel B separation.A
Wire requires orange color coding for channel F separation.B
Reinstall wires W011-90-20, W011-105-20 and W069-071-20 to splice SP2169.C
FIGURE 10: E1-3 ELECTRONICS SHELF - WIRE BUNDLE W069 - WIRING CHANGE
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 13, 2023
737-22A1399 RB
34 of 45
REQUIREMENTS BULLETIN 737-22A1399
ALERTALERT

### Page 35 (OCR)

REQUIREMENTS BULLETIN 737-22A1399
ALERT  ALERT
This Figure applies only to: Group 2.
W011
W101  12  1 002-20 +  20
ЧАНА 059-20 +/А  22
D5945J  P
H+ 061-20 +  110
H+ 058-20+H
36
37
D2209A
M1194 AFC ACCESSORY
UNIT
4H 074-20 +44
44 075-20++  64
D1793B
10
52  GDX20-DC I|  8222-20  56
9
D1791A
19  1H7 056-20 +  + SM114
21444 057-20 +  4A SM115
22 4444077-20+  HA SP2551  - W069
25 -1H4 078-20 +HHSP2553  - W069
W369  7 + 062-20 + SM105
53 7 063-20 +  25
541+ 064-20+  28
W069
SP2169-  8223-20
20+4 060-20+  50
D1795B
24144 079-20 НИНН  ЦІНН  50
36144081-20+  25
291H4 082-20HННН+  28
31  114 080-20+14 SP2247K  - W069  D1661B  M924 FLIGHT CONTROL
W069 - - - /
D4075J  P  CMPTR "A"
E1-3 ELECTRONIC SHELF
ADDED WIRE OR NEW ROUTING  EXISTING WIRE  FLAG NOTE
+ DELETED WIRE OR FORMER ROUTING  >  FIND NUMBER
FIGURE 11: E1-3 ELECTRONICS SHELF - WIRE BUNDLE W011 - WIRING CHANGE
(SHEET 1 OF 2)
Original Issue: April 13, 2023
Export Controlled ECCN: 9E991  737-22A1399 RB
Copyright © Unpublished Work - See page 1 for details.  35 of 45

### Page 36

REFERENCE: 737-300/400/500 WDM 22-11-11, 737-300/400/500 WDM 22-11-71, 737-300/400/500 WDM
22-11-72, 737-300/400/500 WDM 22-13-12
Use wire kit 61-74519-106.
The find numbers (No.) shown below agree with the find number symbol in the figure.
More DataQtyIdentificationName
Find
No.
(a)1BACT12AR204TERMINAL1
(b)2031-9134-004CONTACT2
(c)1D-436-59SPLICE - SEALING
SLEEVE
3
(c)161-74519-10301WIRE, SLEEVE4
(d)(e)161-74519-106WWIRE LIST5
(d)-61-74519-2002LACING TAPE - RED
(d)-61-74519-2001LACING TAPE - ORANGE
(a) Refer to SWPM 20-30-11 and SWPM 20-20-10 as accepted procedures.
(b) Refer to SWPM 20-71-11 as an accepted procedure.
(c) Refer to SWPM 20-30-16 as an accepted procedure.
(d) Refer to SWPM 20-10-11 as an accepted procedure.
(e) Refer to SWPM 20-10-12 as an accepted procedure.
NOTEFlag Note
Wire requires red color coding for channel B separation.A
Wire requires orange color coding for channel F separation.B
Reinstall wires W011-90-20, W011-105-20 and W069-071-20 to splice SP2169.C
FIGURE 11: E1-3 ELECTRONICS SHELF - WIRE BUNDLE W011 - WIRING CHANGE
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 13, 2023
737-22A1399 RB
36 of 45
REQUIREMENTS BULLETIN 737-22A1399
ALERTALERT

### Page 37 (OCR)

REQUIREMENTS BULLETIN 737-22A1399
ALERT  ALERT
This Figure applies only to: Group 3.
W069
нини  36
37
D2209B
M1194 AFC ACCESSORY
UNIT
- 053-20+  61
4052-20+H  64
D1659B
GDX6-DC 110  -592-20  56
D1657A
36 -  + 581-20+4  25
29-14  4# 582-20 +  28
W369  - W011
W011  > SP2169  • 594-20
50
4Н+ 579-20 +
D4075J
D1661B
M923 FLIGHT CONTROL
CMPTR "B"
E1-3 ELECTRONIC SHELF
• ADDED WIRE OR NEW ROUTING  EXISTING WIRE  FLAG NOTE
+ DELETED WIRE OR FORMER ROUTING  FIND NUMBER
FIGURE 12: E1-3 ELECTRONICS SHELF - WIRE BUNDLE W069 - WIRING CHANGE
(SHEET 1 OF 2)
Original Issue: April 13, 2023
Export Controlled ECCN: 9E991  737-22A1399 RB
Copyright © Unpublished Work - See page 1 for details.  37 of 45

### Page 38

REFERENCE: 737-300/400/500 WDM 22-11-72, 737-300/400/500 WDM 22-13-12
Use wire kit 61-74519-107.
The find numbers (No.) shown below agree with the find number symbol in the figure.
More DataQtyIdentificationName
Find
No.
(a)1BACT12AR204TERMINAL1
(b)2031-9134-004CONTACT2
(c)1D-436-59SPLICE - SEALING
SLEEVE
3
(c)161-74519-10301WIRE, SLEEVE4
(d)(e)161-74519-107WWIRE LIST5
(d)-61-74519-2003LACING TAPE - YELLOW
(d)-61-74519-2001LACING TAPE - ORANGE
(a) Refer to SWPM 20-30-11 and SWPM 20-20-10 as accepted procedures.
(b) Refer to SWPM 20-71-11 as an accepted procedure.
(c) Refer to SWPM 20-30-16 as an accepted procedure.
(d) Refer to SWPM 20-10-11 as an accepted procedure.
(e) Refer to SWPM 20-10-12 as an accepted procedure.
NOTEFlag Note
Wire requires yellow color coding for channel B separation.A
Wire requires orange color coding for channel F separation.B
Reinstall wires W011-90-20, W011-105-20 and W069-071-20 to splice SP2169.C
FIGURE 12: E1-3 ELECTRONICS SHELF - WIRE BUNDLE W069 - WIRING CHANGE
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 13, 2023
737-22A1399 RB
38 of 45
REQUIREMENTS BULLETIN 737-22A1399
ALERTALERT

### Page 39 (OCR)

REQUIREMENTS BULLETIN 737-22A1399
ALERT  ALERT
This Figure applies only to: Group 3.
W011
W101  20
4 059-20 44  22
D5945J  110
21
36
37
D2209A
M1194 AFC ACCESSORY
UNIT
· + 074-20 +1+  61
KAAH 075-20 +  64
D1793B
10
52  GDX20-DC 11[  8222-20  56
9
D1791A
19  / 056-20 +H  H/ SM114
21 1H 057-20 +H  H SM115
22 +H# 077-20 +HA SP2551  _ W069
25 +H4 078-20+H SP2553  - W069
W369  7 1H 062-20+H SM105
53 7 063-20 +  25
54 14 064-20 +  28
W069
SP2169  8223-20
HH060-20H  50
D1795B
31  144 080-20+44  • SP2247  M924 FLIGHT CONTROL
D4075J  CMPTR "A"
E1-3 ELECTRONIC SHELF
• ADDED WIRE OR NEW ROUTING  EXISTING WIRE  FLAG NOTE
+ DELETED WIRE OR FORMER ROUTING  FIND NUMBER
FIGURE 13: E1-3 ELECTRONICS SHELF - WIRE BUNDLE W011 - WIRING CHANGE
(SHEET 1 OF 2)
Original Issue: April 13, 2023
Export Controlled ECCN: 9E991  737-22A1399 RB
Copyright © Unpublished Work - See page 1 for details.  39 of 45

### Page 40

REFERENCE: 737-300/400/500 WDM 22-11-11, 737-300/400/500 WDM 22-11-71, 737-300/400/500 WDM
22-11-72, 737-300/400/500 WDM 22-13-12
Use wire kit 61-74519-108.
The find numbers (No.) shown below agree with the find number symbol in the figure.
More DataQtyIdentificationName
Find
No.
(a)1BACT12AR204TERMINAL1
(b)2031-9134-004CONTACT2
(c)1D-436-59SPLICE - SEALING
SLEEVE
3
(c)161-74519-10301WIRE, SLEEVE4
(d)(e)161-74519-108WWIRE LIST5
(d)-61-74519-2002LACING TAPE - RED
(d)-61-74519-2001LACING TAPE - ORANGE
(a) Refer to SWPM 20-30-11 and SWPM 20-20-10 as accepted procedures.
(b) Refer to SWPM 20-71-11 as an accepted procedure.
(c) Refer to SWPM 20-30-16 as an accepted procedure.
(d) Refer to SWPM 20-10-11 as an accepted procedure.
(e) Refer to SWPM 20-10-12 as an accepted procedure.
NOTEFlag Note
Wire requires red color coding for channel B separation.A
Wire requires orange color coding for channel F separation.B
Reinstall wires W011-90-20, W011-105-20 and W069-071-20 to splice SP2169.C
FIGURE 13: E1-3 ELECTRONICS SHELF - WIRE BUNDLE W011 - WIRING CHANGE
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 13, 2023
737-22A1399 RB
40 of 45
REQUIREMENTS BULLETIN 737-22A1399
ALERTALERT

### Page 41 (OCR)

REQUIREMENTS BULLETIN 737-22A1399
ALERT  ALERT
This Figure applies only to: Group 4.
W069
36
37
D2209B
M1194 AFC ACCESSORY
UNIT
HHH 053-20 +  61
4052-20+H  64
D1659B
GDX6-DC I|C  -592-20  56
D1657A
4 581-20 +H  25
44+ 582-20+4  28
+ 577-20+  SM624
2+ 578-20+H  SM625
W369  W011
W011  →SP2169  594-20
4580-20 +H+H  SM626
50
3+H  IHH 579-20 AH
D4359J
D1661B
M923 FLIGHT CONTROL
CMPTR "B"
E1-3 ELECTRONIC SHELF
- ADDED WIRE OR NEW ROUTING  EXISTING WIRE  FLAG NOTE
+ DELETED WIRE OR FORMER ROUTING  FIND NUMBER
FIGURE 14: E1-3 ELECTRONICS SHELF - WIRE BUNDLE W069 - WIRING CHANGE
(SHEET 1 OF 2)
Original Issue: April 13, 2023
737-22A1399 RB
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.  41 0f 45

### Page 42

REFERENCE: 737-300/400/500 WDM 22-11-72, 737-300/400/500 WDM 22-13-12
Use wire kit 61-74519-109.
The find numbers (No.) shown below agree with the find number symbol in the figure.
More DataQtyIdentificationName
Find
No.
(a)1BACT12AR204TERMINAL1
(b)2031-9134-004CONTACT2
(c)1D-436-59SPLICE - SEALING
SLEEVE
3
(c)161-74519-10301WIRE, SLEEVE4
(d)(e)161-74519-109WWIRE LIST5
(d)-61-74519-2003LACING TAPE - YELLOW
(d)-61-74519-2001LACING TAPE - ORANGE
(a) Refer to SWPM 20-30-11 and SWPM 20-20-10 as accepted procedures.
(b) Refer to SWPM 20-71-11 as an accepted procedure.
(c) Refer to SWPM 20-30-16 as an accepted procedure.
(d) Refer to SWPM 20-10-11 as an accepted procedure.
(e) Refer to SWPM 20-10-12 as an accepted procedure.
NOTEFlag Note
Wire requires yellow color coding for channel B separation.A
Wire requires orange color coding for channel F separation.B
Reinstall wires W011-90-20, W011-105-20 and W069-071-20 to splice SP2169.C
FIGURE 14: E1-3 ELECTRONICS SHELF - WIRE BUNDLE W069 - WIRING CHANGE
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 13, 2023
737-22A1399 RB
42 of 45
REQUIREMENTS BULLETIN 737-22A1399
ALERTALERT

### Page 43 (OCR)

REQUIREMENTS BULLETIN 737-22A1399
ALERT  ALERT
This Figure applies only to: Group 4.
W011
W101  12  VH+ 002-20 +  20
22
D5945J  P
44 061-20 +  110
44058-20+4  21
36
37
D2209A
M1194 AFC ACCESSORY
UNIT
+ 074-20+44H  61
H 075-20 +  64
D1793B
52  GDX20-DC I|  8222-20  56
9
D1791A
19  + 056-20;  + SM114
21 144 057-20+  4 SM115
7 + 062-20+  YA SM105
W369
53 1 063-20 +  25
54 + 064-20 +  28
W069
SP2169  8223-20
-060-20  50
D4075J  P  D1795B
M924 FLIGHT CONTROL
CMPTR "A"
E1-3 ELECTRONIC SHELF
- ADDED WIRE OR NEW ROUTING
+ DELETED WIRE OR FORMER ROUTING
- EXISTING WIRE
FIND NUMBER  3019886
FLAG NOTE
FIGURE 15: E1-3 ELECTRONICS SHELF - WIRE BUNDLE W011 - WIRING CHANGE
(SHEET 1 OF 2)
Original Issue: April 13, 2023
Copyright © Unpublished Work - See page 1 for details.  Export Controlled ECCN: 9E991  737-22A1399 RB  43 of 45

### Page 44

REFERENCE: 737-300/400/500 WDM 22-11-11, 737-300/400/500 WDM 22-11-71, 737-300/400/500 WDM
22-13-12
Use wire kit 61-74519-110.
The find numbers (No.) shown below agree with the find number symbol in the figure.
More DataQtyIdentificationName
Find
No.
(a)1BACT12AR204TERMINAL1
(b)2031-9134-004CONTACT2
(c)1D-436-59SPLICE - SEALING
SLEEVE
3
(c)161-74519-10301WIRE, SLEEVE4
(d)(e)161-74519-110WWIRE LIST5
(d)-61-74519-2002LACING TAPE - RED
(d)-61-74519-2001LACING TAPE - ORANGE
(a) Refer to SWPM 20-30-11 and SWPM 20-20-10 as accepted procedures.
(b) Refer to SWPM 20-71-11 as an accepted procedure.
(c) Refer to SWPM 20-30-16 as an accepted procedure.
(d) Refer to SWPM 20-10-11 as an accepted procedure.
(e) Refer to SWPM 20-10-12 as an accepted procedure.
NOTEFlag Note
Wire requires red color coding for channel B separation.A
Wire requires orange color coding for channel F separation.B
Reinstall wires W011-90-20, W011-105-20 and W069-071-20 to splice SP2169.C
FIGURE 15: E1-3 ELECTRONICS SHELF - WIRE BUNDLE W011 - WIRING CHANGE
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 13, 2023
737-22A1399 RB
44 of 45
REQUIREMENTS BULLETIN 737-22A1399
ALERTALERT

### Page 45

1. Supply electrical power to the airplane. Refer to 737-300/400/500 AMM 24-22-00 as an accepted
procedure.
2. Do the Aileron And Aileron Trim Control System Test that follows:
a. Do the steps that follow to make sure the control wheel and control column moves freely:
(1) Move the control column forward and aft, and the control wheel left and right between 4 to 6
times between their stops.
(2) Hold the control wheel against the left stop. Move the control column forward and aft between
the stops.
(3) Hold the control wheel against the right stop. Move the control column forward and aft between
the stops.
(4) Hold the control column full forward and move the control wheel to the left and right between
the stops.
(5) Hold the control column full aft and move the control wheel to the left and right between the
stops.
b. If the control wheel or control column does not move freely, the Aileron and Aileron Trim Control
System Test failed.
3. Do Flight Control Computer Test and make sure the test is completed without an indication of failure.
Any indication of failure, the test is failed. Refer to 737-300/400/500 AMM 22-11-33 as an accepted
procedure.
4. Do a BITE Option Pin Check of the Digital Flight Control System (DFCS) to check pin 56 is SOP - ELEC
AIL LIM is 1. If SOP - ELEC AIL LIM is not 1, test is failed. Refer to 737-300/400/500 AMM 22-11-00
as an accepted procedure.
5. Do a BITE ground test of the DFCS of library test 60. The test is satisfactory unless a TEST FAILED
indication is shown. Refer to 737-300/400/500 AMM 22-11-00 as an accepted procedure.
NOTE: If the addition of pin A56 creates an even parity condition, it will be necessary to revise the
parity pin (FCC pin A42) to keep odd parity.
APPENDIX C:  TESTS
(SHEET 1 OF 1)
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 13, 2023
737-22A1399 RB
45 of 45
REQUIREMENTS BULLETIN 737-22A1399
ALERTALERT

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
