# Boeing Alert Service Bulletin 737-25A1544: Revision 4, part 2 of 2

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2023-1886; AD 2024-18-07 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Alert Service Bulletin 737-25A1544](https://openairdocs.org/service-documents/boeing/737-25a1544.md)
- Title as filed: SB-737-25A1544-04--_Part2
- Pages: 78
- PDF: https://openairdocs.org/files/sha256/57/4c/574c739c69403406c10f379dc6f227d41f80895ab07c2dac4708350fc19e8f32
- Page: https://openairdocs.org/service-documents/boeing/737-25a1544/file/574c739c6940

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1 (OCR)

BOEING SERVICE BULLETIN 737-25A1544
ALERT  ALERT
COO FILLER B
CUT OUT AREA € 67
AND FILLER C
2) 3) ANGLE C
FRAME SHEAR TIE
FAILSAFE CHORD
FOR CUT OUT ACROSS ENTIRE SECTION  /D
(BELOW S-8L)
B-B
2291747
FIGURE 13: LEFT SIDE, STA 907 FRAME, SUPPORT BRACKET ATTACHMENT HOLES AT THE AIR
CONDITIONING EXTRUSION - MAKE REPAIR PARTS (OPTION 1)
(SHEET 7 OF 9)
Original Issue: October 04, 2006
Revision 4 February 15, 2022  737-25A1544
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.  125 of 202

### Page 2

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for one body frame.
More DataQtyIdentificationNameTaskStep
(a)(b)(g)1ANGLE CREPAIR ANGLE CMake1
From the annealed
condition to the T6
condition after form-
ing.
1ANGLE CREPAIR ANGLE CHeat Treat2
(c)1ANGLE CREPAIR ANGLE CInspect3
(d)(e)(g)1FILLER BFILLERMake4
(c)(f)(g)1FILLER CFILLERMake5
(h)-TYPE 2, CLASS ACHEMICAL CONVER-
SION COATING
Apply6
(i)-BMS 10-11, TYPE 1PRIMERApply7
(a) If the existing frame web is 0.056 inch thick, make Repair Angle C from 0.063 inch thick 7075-0 clad sheet
with minimum bend radius of 0.12 inch. If the existing frame web is 0.071 inch thick, make Repair Angle
C from 0.080 inch thick 7075-0 clad sheet with minimum bend radius of 0.19 inch. Form the repair angles
in the annealed condition to match the contour of the frame in accordance with 737-600 SRM 51-30-01,
737-700 SRM 51-30-01, 737-800 SRM 51-30-01, 737-800BCF SRM 51-30-01 or 737-900 SRM 51-30-
01.
(b) Make sure that the length of the repair angle is sufficient to have a minimum of five rows of fasteners
common to the frame inboard flange and a minimum of five rows of fasteners common to the frame web
above and below the cut out area.
(c) Do a dye penetrant inspection of the bend radius to make sure there is no crack. Refer to SOPM 20-20-
02 as an accepted procedure.
(d) Make Filler B from 0.050 inch thick 7075-T6 clad sheet. Make sure that Filler B has the same thickness
as the frame shear tie.
(e) Extend Filler B one row of fasteners beyond Repair Angle C on either side of the repair area.
(f) Make Filler C from 7075-T6 clad sheet or from 7075-0 clad sheet if it need to be form, that has the same
thickness as the existing frame. Filler C can be formed with minimum bend radius of 0.19 inch. Form in
the annealed condition to match the contour of the frame in accordance with 737-600 SRM 51-30-01,
737-700 SRM 51-30-01, 737-700IGW SRM 51-30-01, 737-800 SRM 51-30-01, 737-800BCF SRM 51-30-
01 or 737-900 SRM 51-30-01, and heat treat to T6.
(g) Maintain a 0.50 inch minimum corner radius. Maintain a minimum 2D edge margin. Maintain 63 microinches
Ra or better surface finish on all cut surfaces. Break sharp edges. Make sure that the repair parts do not
end common to the stringer clip. Extending the repair parts one row of fasteners beyond the stringer clip
is acceptable.
(h) Apply chemical conversion coating to all bare aluminum surfaces. Refer to SOPM 20-43-03 as an accepted
procedure.
FIGURE 13: LEFT SIDE, STA 907 FRAME, SUPPORT BRACKET ATTACHMENT HOLES AT THE AIR
CONDITIONING EXTRUSION - MAKE REPAIR PARTS (OPTION 1)
(SHEET 8 OF 9)
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: October 04, 2006
737-25A1544Revision 4 February 15, 2022
126 of 202
BOEING SERVICE BULLETIN 737-25A1544
ALERTALERT

### Page 3

More DataQtyIdentificationNameTaskStep
(i) Apply two layers of BMS 10-11, Type 1 primer to all surfaces where chemical conversion coating was
applied. Refer to SOPM 20-41-02 as an accepted procedure.
FIGURE 13: LEFT SIDE, STA 907 FRAME, SUPPORT BRACKET ATTACHMENT HOLES AT THE AIR
CONDITIONING EXTRUSION - MAKE REPAIR PARTS (OPTION 1)
(SHEET 9 OF 9)
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: October 04, 2006
737-25A1544Revision 4 February 15, 2022
127 of 202
BOEING SERVICE BULLETIN 737-25A1544
ALERTALERT

### Page 4 (OCR)

BOEING SERVICE BULLETIN 737-25A1544
ALERT  ALERT
This Figure applies only to: Group 1-4, 6.
STA
907
4O1 FILLER B
-- S-7R
FRAME
SHEAR TIE
SUPPORT
FITTING
STRINGER
CLIP
•- S-8R
SUPPORT BRACKET
FRAME
MAXIMUM
67  CUT OUT  AREA AND
FILLER C
ANGLEC Q23
FAILSAFE
CHORD
FRAME SHEAR
TIE
- S-9R
INBD  STA 907  2293611
FIGURE 14: RIGHT SIDE, STA 907 FRAME, SUPPORT BRACKET ATTACHMENT HOLES AT THE AIR
CONDITIONING EXTRUSION - MAKE REPAIR PARTS (OPTION 1)
(SHEET 1 OF 9)
Original Issue: October 04, 2006
Revision 4 February 15, 2022  737-25A1544
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.  128 of 202

### Page 5 (OCR)

BOEING SERVICE BULLETIN 737-25A1544
ALERT  ALERT
FILLER B COO
FRAME
ANGLE C O2
FRAME SHEAR TIE
FAILSAFE CHORD
ABOVE AND BELOW THE
CUT OUT AREA
(TYPICAL)
FWD
A-A
2293613
FIGURE 14: RIGHT SIDE, STA 907 FRAME, SUPPORT BRACKET ATTACHMENT HOLES AT THE AIR
CONDITIONING EXTRUSION - MAKE REPAIR PARTS (OPTION 1)
(SHEET 2 OF 9)
Original Issue: October 04, 2006
Revision 4 February 15, 2022  737-25A1544
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.  129 of 202

### Page 6 (OCR)

BOEING SERVICE BULLETIN 737-25A1544
ALERT  ALERT
FILLER B 46
— FRAME
1OO AND PILLARCA
OUTBOARD
HOLE
ANGLEC CO  - FRAME
FRAME SHEAR TIE
FAILSAFE CHORD
FOR CUT OUT ONLY AT INBOARD HOLE
(BELOW S-8R)
-WD  B-B
2293625
FIGURE 14: RIGHT SIDE, STA 907 FRAME, SUPPORT BRACKET ATTACHMENT HOLES AT THE AIR
CONDITIONING EXTRUSION - MAKE REPAIR PARTS (OPTION 1)
(SHEET 3 OF 9)
Original Issue: October 04, 2006
Revision 4 February 15, 2022  Export Controlled ECCN: 9E991  737-25A1544
Copyright © Unpublished Work - See page 1 for details.  130 of 202

### Page 7 (OCR)

BOEING SERVICE BULLETIN 737-25A1544
ALERT  ALERT
FILLER B COO
FRAME
INBOARD
HOLE
ANGLEC OO®  16X7) CUT OUT ARE  AND FILLER O
FRAME SHEAR TIE
• FAILSAFE CHORD
FOR CUT OUT ONLY AT OUTBOARD HOLE
(BELOW S-8R)
-WD  B-B
2293627
FIGURE 14: RIGHT SIDE, STA 907 FRAME, SUPPORT BRACKET ATTACHMENT HOLES AT THE AIR
CONDITIONING EXTRUSION - MAKE REPAIR PARTS (OPTION 1)
(SHEET 4 OF 9)
Original Issue: October 04, 2006
Revision 4 February 15, 2022  Export Controlled ECCN: 9E991  737-25A1544
Copyright © Unpublished Work - See page 1 for details.  131 of 202

### Page 8 (OCR)

BOEING SERVICE BULLETIN 737-25A1544
ALERT  ALERT
FILLER B 46 O
FRAME
SOO ANT ALL AREA
ANGLE C Q2
FRAME SHEAR TIE
FAILSAFE CHORD
FWD
FOR CUT OUT AT INBOARD AND OUTBOARD HOLE
(BELOW S-8R)
B-B  2293630
FIGURE 14: RIGHT SIDE, STA 907 FRAME, SUPPORT BRACKET ATTACHMENT HOLES AT THE AIR
CONDITIONING EXTRUSION - MAKE REPAIR PARTS (OPTION 1)
(SHEET 5 OF 9)
Original Issue: October 04, 2006
Revision 4 February 15, 2022  Export Controlled ECCN: 9E991  737-25A1544
Copyright © Unpublished Work - See page 1 for details.  132 of 202

### Page 9 (OCR)

BOEING SERVICE BULLETIN 737-25A1544
ALERT  ALERT
FILLER B COO
16X7) CUT OUT ARE  AND FILLER (
OUTBOARD
HOLE
ANGLE C 2O0  - FRAME
FRAME SHEAR TIE
FAILSAFE CHORD
FOR CUT OUT ONLY AT INBOARD
HOLE AND INNER FLANGE
(BELOW S-8R)
-WD  B-B
2293631
FIGURE 14: RIGHT SIDE, STA 907 FRAME, SUPPORT BRACKET ATTACHMENT HOLES AT THE AIR
CONDITIONING EXTRUSION - MAKE REPAIR PARTS (OPTION 1)
(SHEET 6 OF 9)
Original Issue: October 04, 2006
Revision 4 February 15, 2022  737-25A1544
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.  133 of 202

### Page 10 (OCR)

BOEING SERVICE BULLETIN 737-25A1544
ALERT  ALERT
FILLER B 4€
ĐOO AND PILL AREA
ANGLE COO
J
FRAME SHEAR TIE
→ FAILSAFE CHORD
FOR CUT OUT ACROSS ENTIRE SECTION
(BELOW S-8R)
-WD  B-B
2293633
FIGURE 14: RIGHT SIDE, STA 907 FRAME, SUPPORT BRACKET ATTACHMENT HOLES AT THE AIR
CONDITIONING EXTRUSION - MAKE REPAIR PARTS (OPTION 1)
(SHEET 7 OF 9)
Original Issue: October 04, 2006
Revision 4 February 15, 2022  Export Controlled ECCN: 9E991  737-25A1544
Copyright © Unpublished Work - See page 1 for details.  134 of 202

### Page 11

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for one body frame.
More DataQtyIdentificationNameTaskStep
(a)(b)(g)1ANGLE CREPAIR ANGLE CMake1
From the annealed
condition to the T6
condition after form-
ing.
1ANGLE CREPAIR ANGLE CHeat Treat2
(c)1ANGLE CREPAIR ANGLE CInspect3
(d)(e)(g)1FILLER BFILLERMake4
(c)(f)(g)1FILLER CFILLERMake5
(h)-TYPE 2, CLASS ACHEMICAL CONVER-
SION COATING
Apply6
(i)-BMS 10-11, TYPE 1PRIMERApply7
(a) If the existing frame web is 0.056 inch thick, make Repair Angle C from 0.063 inch thick 7075-0 clad sheet
with minimum bend radius of 0.12 inch. If the existing frame web is 0.071 inch thick, make Repair Angle
C from 0.080 inch thick 7075-0 clad sheet with minimum bend radius of 0.19 inch. Form the repair angles
in the annealed condition to match the contour of the frame in accordance with 737-600 SRM 51-30-01,
737-700 SRM 51-30-01, 737-800 SRM 51-30-01, 737-800BCF SRM 51-30-01 or 737-900 SRM 51-30-
01.
(b) Make sure that the length of the repair angle is sufficient to have a minimum of five rows of fasteners
common to the frame inboard flange and a minimum of five rows of fasteners common to the frame web
above and below the cut out area.
(c) Do a dye penetrant inspection of the bend radius to make sure there is no crack. Refer to SOPM 20-20-
02 as an accepted procedure.
(d) Make Filler B from 0.050 inch thick 7075-T6 clad sheet. Make sure that Filler B has the same thickness
as the frame shear tie.
(e) Extend Filler B one row of fasteners beyond Repair Angle C on either side of the repair area.
(f) Make Filler C from 7075-T6 clad sheet or from 7075-0 clad sheet if it need to be form, that has the same
thickness as the existing frame. Filler C can be formed with minimum bend radius of 0.19 inch. Form in
the annealed condition to match the contour of the frame in accordance with 737-600 SRM 51-30-01,
737-700 SRM 51-30-01, 737-700IGW SRM 51-30-01, 737-800 SRM 51-30-01, 737-800BCF SRM 51-30-
01 or 737-900 SRM 51-30-01, and heat treat to T6.
(g) Maintain a 0.50 inch minimum corner radius. Maintain a minimum 2D edge margin. Maintain 63 microinches
Ra or better surface finish on all cut surfaces. Break sharp edges. Make sure that the repair parts do not
end common to the stringer clip. Extending the repair parts one row of fasteners beyond the stringer clip
is acceptable.
(h) Apply chemical conversion coating to all bare aluminum surfaces. Refer to SOPM 20-43-03 as an accepted
procedure.
FIGURE 14: RIGHT SIDE, STA 907 FRAME, SUPPORT BRACKET ATTACHMENT HOLES AT THE AIR
CONDITIONING EXTRUSION - MAKE REPAIR PARTS (OPTION 1)
(SHEET 8 OF 9)
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: October 04, 2006
737-25A1544Revision 4 February 15, 2022
135 of 202
BOEING SERVICE BULLETIN 737-25A1544
ALERTALERT

### Page 12

More DataQtyIdentificationNameTaskStep
(i) Apply two layers of BMS 10-11, Type 1 primer to all surfaces where chemical conversion coating was
applied. Refer to SOPM 20-41-02 as an accepted procedure.
FIGURE 14: RIGHT SIDE, STA 907 FRAME, SUPPORT BRACKET ATTACHMENT HOLES AT THE AIR
CONDITIONING EXTRUSION - MAKE REPAIR PARTS (OPTION 1)
(SHEET 9 OF 9)
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: October 04, 2006
737-25A1544Revision 4 February 15, 2022
136 of 202
BOEING SERVICE BULLETIN 737-25A1544
ALERTALERT

### Page 13 (OCR)

BOEING SERVICE BULLETIN 737-25A1544
ALERT  ALERT
This Figure applies only to: Group 1-4, 6.
STA
907
S-7L
FRAME
SHEAR TIE
SUPPORT
FITTING
14 LOCATIONS
(TYPICAL)
SUPPORT
STRINGER  BRACKET
CLIP
S-8L --
ANGLE C
FAILSAFE CHORD
CUT OUT AREA  - FRAME
AND FILLER C
(TYPICAL)
1334
FILLER B
S-9L -
FRAME SHEAR
TIE
STA 907  INBD  2292758
FIGURE 15: LEFT SIDE, STA 907 FRAME, SUPPORT BRACKET ATTACHMENT HOLES AT THE AIR
CONDITIONING EXTRUSION - INSTALL REPAIR PARTS (OPTION 1)
(SHEET 1 OF 8)
Original Issue: October 04, 2006
Revision 4 February 15, 2022  737-25A1544
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.  137 of 202

### Page 14 (OCR)

BOEING SERVICE BULLETIN 737-25A1544
ALERT  ALERT
S-8L
B
FILLER B
INBD
2292120
FIGURE 15: LEFT SIDE, STA 907 FRAME, SUPPORT BRACKET ATTACHMENT HOLES AT THE AIR
CONDITIONING EXTRUSION - INSTALL REPAIR PARTS (OPTION 1)
(SHEET 2 OF 8)
Original Issue: October 04, 2006
Revision 4 February 15, 2022  737-25A1544
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.  138 of 202

### Page 15 (OCR)

BOEING SERVICE BULLETIN 737-25A1544
ALERT  ALERT
STRINGER
, ANGLE C
FRAME •
FILLER BI
STA
907
A-A
STRINGER
STA_
907
FILLER B
FRAME
ANGLE C
B-B  2458896
FIGURE 15: LEFT SIDE, STA 907 FRAME, SUPPORT BRACKET ATTACHMENT HOLES AT THE AIR
CONDITIONING EXTRUSION - INSTALL REPAIR PARTS (OPTION 1)
(SHEET 3 OF 8)
Original Issue: October 04, 2006
Revision 4 February 15, 2022  737-25A1544
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.  139 of 202

### Page 16 (OCR)

BOEING SERVICE BULLETIN 737-25A1544
ALERT  ALERT
STA 907
S-7L -
S-8L -
S-9L
FWD  2459095
C-C
FIGURE 15: LEFT SIDE, STA 907 FRAME, SUPPORT BRACKET ATTACHMENT HOLES AT THE AIR
CONDITIONING EXTRUSION - INSTALL REPAIR PARTS (OPTION 1)
(SHEET 4 OF 8)
Original Issue: October 04, 2006
Revision 4 February 15, 2022  Export Controlled ECCN: 9E991  737-25A1544
Copyright © Unpublished Work - See page 1 for details.  140 of 202

### Page 17

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for one body frame.
More DataQtyIdentificationNameTaskStep
-1FILLER BFILLERRemove / Keep1
-1FILLER CFILLERRemove / Keep
-1ANGLE CREPAIR ANGLE CRemove / Keep
-2147A1007-( )FRAME SHEAR TIERemove / Keep
-1147A3500-13STRINGER CLIPRemove / Keep
-1412A3210-( )SUPPORT BRACKETRemove / Keep
-1147A9100-()SUPPORT FITTINGRemove / Keep
(d)--PARTSDeburr
-1FILLER BFILLERPut / Hold2
-1FILLER CFILLERPut / Hold
-1ANGLE CREPAIR ANGLE CPut / Hold
-2147A1007-( )FRAME SHEAR TIEPut / Hold
-1147A3500-13STRINGER CLIPPut / Hold
-1412A3210-( )SUPPORT BRACKETPut / Hold
(a)(b)(c)--HOLEDrill
1147A9100-()SUPPORT FITTINGPut / Hold
(e)-TYPE 2, CLASS ACHEMICAL CONVER-
SION COATING
Apply3
(f)-BMS 10-11, TYPE 1PRIMERApply
(g)-BMS 5-95, CLASS B-
1/2, B-2
SEALANTApply4
(h)1FILLER BFILLERInstall (New)
(h)1FILLER CFILLERInstall (New)
(h)1ANGLE CREPAIR ANGLE CInstall (New)
(j)--RADIUS FILLERInstall (New)
(i)--FASTENERInstall (New)
(h)1147A3500-13STRINGER CLIPInstall (New)5
(i)--FASTENERInstall (New)
(h)2147A1007-( )FRAME SHEAR TIEInstall (Kept)6
(i)--FASTENERInstall (New)
FIGURE 15: LEFT SIDE, STA 907 FRAME, SUPPORT BRACKET ATTACHMENT HOLES AT THE AIR
CONDITIONING EXTRUSION - INSTALL REPAIR PARTS (OPTION 1)
(SHEET 5 OF 8)
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: October 04, 2006
737-25A1544Revision 4 February 15, 2022
141 of 202
BOEING SERVICE BULLETIN 737-25A1544
ALERTALERT

### Page 18

More DataQtyIdentificationNameTaskStep
(h)(m)1412A3210-( )SUPPORT BRACKETInstall (Kept)7
(i)(m)2-FASTENERInstall (New)
(l)(m)1147A9100-()SUPPORT FITTINGInstall (Kept)8
(l)(m)2-FASTENERInstall (Kept)
(k)-BMS 3-29 (BMS 3-23
or BMS 3-35 optional)
CORROSION INHIBIT-
ING COMPOUND
Apply9
(a) Drill fastener holes in Filler B, Filler C, Repair Angle C, frame shear ties, stringer clip, support bracket,
support fitting and frame.
(b) Maintain a minimum 2D edge margin and 4D-6D fastener spacing at new fastener locations.
(c) At existing fastener locations only, it is permitted to make the hole size a maximum of 1/32 inch larger
than the existing diameter. Refer to the fastener code table below. Maintain a minimum 1.7D edge margin.
(d) Remove all nicks, scratches, gouges, burrs, and sharp edges from the repair parts and installed parts.
(e) Apply chemical conversion coating to all bare aluminum surfaces. Refer to SOPM 20-43-03 as an accepted
procedure.
(f) Apply two layers of BMS 10-11, Type 1 primer to all surfaces where chemical conversion coating was
applied. Refer to SOPM 20-41-02 as an accepted procedure.
(g) Apply sealant to all faying surfaces and apply a fillet seal around the edges of the repair. Refer to SOPM
20-50-19 as an accepted procedure.
(h) Maximum clearance between mating parts before fastener installation 0.010 inch. Install shims as neces-
sary. Maximum shim thickness 0.040 inch. Refer to SOPM 20-50-20 as an accepted procedure.
(i) Refer to the fastener code table below.
(j) If required, install a local 7075 aluminum radius filler at each fastener common to the frame flange to seat
the fastener properly. Do not use a continuous radius filler. The filler can be made from the following three
material options: 7075-0 aluminum alloy, 7075-T6 aluminum alloy, or 7075-0 aluminum alloy and heat
treated to the T6 condition after the filler is made.
(k) Apply corrosion inhibiting compound to the repair area. Refer to SOPM 20-41-05 as an accepted procedure.
(l) Maximum clearance between mating parts before fastener installation 0.010 inch. Shim installation is
acceptable to achieve clearance. Maximum shim thickness 0.040 inch. Refer to SOPM 20-50-20 as an
accepted procedure.
(m) Install all fasteners in accordance with 737-600 SRM 51-40-02, 737-700 SRM 51-40-02, 737-700IGW
SRM 51-40-02, 737-800 SRM 51-40-02, 737-800BCF SRM 51-40-02, or 737-900 SRM 51-40-02. Overdrive
all rivet shanks to 1.5D.
FIGURE 15: LEFT SIDE, STA 907 FRAME, SUPPORT BRACKET ATTACHMENT HOLES AT THE AIR
CONDITIONING EXTRUSION - INSTALL REPAIR PARTS (OPTION 1)
(SHEET 6 OF 8)
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: October 04, 2006
737-25A1544Revision 4 February 15, 2022
142 of 202
BOEING SERVICE BULLETIN 737-25A1544
ALERTALERT

### Page 19

The codes shown below agree with the letter shown in the upper left corner of the fastener symbols in the figure.
NOTESHOLE DIAPART NUMBERNAMECODE
Use to install stringer clip
on stringer. (a)
0.187 - 0.190BACB30FM6A2, BACC30M6Hi-lok, CollarA
Use when frame gage is
0.056 inch. (a)(b)
0.187 - 0.190BACB30FM6A3, BACC30M6Hi-lok, Collar
Use when frame gage is
0.071 inch. (a)(b)
0.187 - 0.190BACB30FM6A4, BACC30M6Hi-lok, Collar
Use when frame gage is
0.056 inch. (a)
0.247 - 0.250BACB30NX8K4,
BACC30BH8
Hi-lok, CollarD
Use when frame gage is
0.071 inch. (a)
0.247 - 0.250BACB30NX8K5,
BACC30BH8
Hi-lok, Collar
Use when frame gage is
0.056 inch. (a)(c)
0.200 - 0.203BACB30MC6A4, BACC30X6Hi-lok, CollarE
Use when frame gage is
0.071 inch. (a)(c)
0.200 - 0.203BACB30MC6A5, BACC30X6Hi-lok, Collar
Use when frame gage is
0.056 inch. (a)(d)
0.216 - 0.219BACB30MD6A4,
BACC30AC6
Hi-lok, Collar
Use when frame gage is
0.071 inch. (a)(d)
0.216 - 0.219BACB30MD6A5,
BACC30AC6
Hi-lok, Collar
-0.190 - 0.196BACR15GF6D6RivetF
Use when frame gage is
0.056 inch. (a)(c)(b)
0.200 - 0.203BACB30MC6A3, BACC30X6Hi-lok, CollarG
Use when frame gage is
0.071 inch. (a)(c)(b)
0.200 - 0.203BACB30MC6A4, BACC30X6Hi-lok, Collar
Use when frame gage is
0.056 inch. (a)(d)(b)
0.216 - 0.219BACB30MD6A3,
BACC30AC6
Hi-lok, Collar
Use when frame gage is
0.071 inch. (a)(d)(b)
0.216 - 0.219BACB30MD6A4,
BACC30AC6
Hi-lok, Collar
Use when frame gage is
0.056 inch. (a)(b)
0.187 - 0.190BACB30FM6A2, BACC30M6Hi-lok, CollarH
Use when frame gage is
0.071 inch. (a)(b)
0.187 - 0.190BACB30FM6A3, BACC30M6Hi-lok, Collar
FIGURE 15: LEFT SIDE, STA 907 FRAME, SUPPORT BRACKET ATTACHMENT HOLES AT THE AIR
CONDITIONING EXTRUSION - INSTALL REPAIR PARTS (OPTION 1)
(SHEET 7 OF 8)
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: October 04, 2006
737-25A1544Revision 4 February 15, 2022
143 of 202
BOEING SERVICE BULLETIN 737-25A1544
ALERTALERT

### Page 20

NOTESHOLE DIAPART NUMBERNAMECODE
Use when frame gage is
0.056 inch. (a)(c)
0.200 - 0.203BACB30MC6A2, BACC30X6Hi-lok, CollarI
Use when frame gage is
0.071 inch. (a)(c)
0.200 - 0.203BACB30MC6A3, BACC30X6Hi-lok, Collar
Use when frame gage is
0.056 inch. (a)(d)
0.216 - 0.219BACB30MD6A2,
BACC30AC6
Hi-lok, Collar
Use when frame gage is
0.071 inch. (a)(d)
0.216 - 0.219BACB30MD6A3,
BACC30AC6
Hi-lok, Collar
Use when frame gage is
0.056 inch. (a)(d)
0.200 - 0.203BACB30MC6A7, BACC30X6Hi-lok, CollarJ
Use when frame gage is
0.056 inch.(a)(d)
0.216 - 0.219BACB30MC6A7, BACC30X6Hi-lok, Collar
Use when frame gage is
0.071 inch.(a)(d)
0.200 - 0.203BACB30MD6A8,
BACC30AX6
Hi-lok, Collar
Use when frame gage is
0.071 inch.(a)(d)
0.216 - 0.219BACB30MD6A8,
BACC30AC6
Hi-lok, Collar
(a) Install wet with BMS 5-95 sealant. Refer to SOPM 20-50-19, Corrosion Protection Sealing, Method
2, as an accepted procedure.
(b) If fastener is installed at a location which requires a radius filler, measure build-up to determine grip
length.
(c) This fastener has a 1/64 (first) nominal oversize shank.
(d) This fastener has a 1/32 (second) nominal oversize shank.
FIGURE 15: LEFT SIDE, STA 907 FRAME, SUPPORT BRACKET ATTACHMENT HOLES AT THE AIR
CONDITIONING EXTRUSION - INSTALL REPAIR PARTS (OPTION 1)
(SHEET 8 OF 8)
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: October 04, 2006
737-25A1544Revision 4 February 15, 2022
144 of 202
BOEING SERVICE BULLETIN 737-25A1544
ALERTALERT

### Page 21 (OCR)

BOEING SERVICE BULLETIN 737-25A1544
ALERT  ALERT
This Figure applies only to: Group 1-4, 6.
STA
907
• S-7R
B
112) 6)
FRAME
SHEAR TIE
SUPPORT
FITTING
I4 LOCATIONS
TYPICAL
BRACKET 1X2) 7  UPPORT  5
STRINGER
CLIF
-- S-8R
ANGLE C 12 3 4
› CUT OUT AREA
AND FILLER C
(34 (TYPICAL)
FAILSAFE CHORD •
FRAME
FILLER B 12 34
FRAME SHEAR
• S-9R  TIE
INBD
STA 907
FIGURE 16: RIGHT SIDE, STA 907 FRAME, SUPPORT BRACKET ATTACHMENT HOLES AT THE AIR
CONDITIONING EXTRUSION - INSTALL REPAIR PARTS (OPTION 1)
(SHEET 1 OF 7)
Original Issue: October 04, 2006
Revision 4 February 15, 2022  737-25A1544
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.  145 of 202

### Page 22 (OCR)

BOEING SERVICE BULLETIN 737-25A1544
ALERT  ALERT
S-8R
STRINGER
ANGLE C
• FRAME
FILLER B
STA
907
A-A  2293602
FIGURE 16: RIGHT SIDE, STA 907 FRAME, SUPPORT BRACKET ATTACHMENT HOLES AT THE AIR
CONDITIONING EXTRUSION - INSTALL REPAIR PARTS (OPTION 1)
(SHEET 2 OF 7)
Original Issue: October 04, 2006
Revision 4 February 15, 2022  Export Controlled ECCN: 9E991  737-25A1544
Copyright © Unpublished Work - See page 1 for details.  146 of 202

### Page 23 (OCR)

BOEING SERVICE BULLETIN 737-25A1544
ALERT  ALERT
STA 907
- S-7R
- S-8R
- S-9R
FWD  2459113
B-B
FIGURE 16: RIGHT SIDE, STA 907 FRAME, SUPPORT BRACKET ATTACHMENT HOLES AT THE AIR
CONDITIONING EXTRUSION - INSTALL REPAIR PARTS (OPTION 1)
(SHEET 3 OF 7)
Original Issue: October 04, 2006
Revision 4 February 15, 2022  737-25A1544
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.  147 of 202

### Page 24

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for one body frame.
More DataQtyIdentificationNameTaskStep
-1FILLER BFILLERPut / Hold1
-1FILLER CFILLERPut / Hold
-1ANGLE CREPAIR ANGLE CPut / Hold
-2147A1007-( )FRAME SHEAR TIEPut / Hold
-1147A3500-( )STRINGER CLIPPut / Hold
-1412A3210-( )SUPPORT BRACKETPut / Hold
-1147A9100-()SUPPORT FITTINGPut / Hold
(a)(b)(c)--HOLEDrill
-1FILLER BFILLERRemove / Keep2
-1FILLER CFILLERRemove / Keep
-1ANGLE CREPAIR ANGLE CRemove / Keep
-2147A1007-( )FRAME SHEAR TIERemove / Keep
-1147A3500-( )STRINGER CLIPRemove / Keep
-1412A3210-( )SUPPORT BRACKETRemove / Keep
(d)--PARTSDeburr
(e)-TYPE 2, CLASS ACHEMICAL CONVER-
SION COATING
Apply3
(f)-BMS 10-11, TYPE 1PRIMERApply
(g)-BMS 5-95, CLASS B-
1/2, B-2
SEALANTApply4
(h)1FILLER BFILLERInstall (New)
(h)1FILLER CFILLERInstall (New)
(h)1ANGLE CREPAIR ANGLE CInstall (New)
(j)--RADIUS FILLERInstall (New)
(i)--FASTENERInstall (New)
(h)1147A3500-( )STRINGER CLIPInstall (New)5
(i)--FASTENERInstall (New)
(h)(m)2147A1007-( )FRAME SHEAR TIEInstall (Kept)6
(i)(m)--FASTENERInstall (New)
FIGURE 16: RIGHT SIDE, STA 907 FRAME, SUPPORT BRACKET ATTACHMENT HOLES AT THE AIR
CONDITIONING EXTRUSION - INSTALL REPAIR PARTS (OPTION 1)
(SHEET 4 OF 7)
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: October 04, 2006
737-25A1544Revision 4 February 15, 2022
148 of 202
BOEING SERVICE BULLETIN 737-25A1544
ALERTALERT

### Page 25

More DataQtyIdentificationNameTaskStep
(h)(m)1412A3210-( )SUPPORT BRACKETInstall (Kept)7
(i)(m)2-FASTENERInstall (New)
(l)1147A9100-()SUPPORT FITTINGInstall (Kept)8
(m)2-FASTENERInstall (Kept)
(k)-BMS 3-29 (BMS 3-23
or BMS 3-35 optional)
CORROSION INHIBIT-
ING COMPOUND
Apply9
(a) Drill fastener holes in Filler B, Filler C, Repair Angle C, frame shear ties, stringer clip, support bracket,
support fitting and frame.
(b) Stagger fasteners to maintain a minimum 2D edge margin and 4D-6D fastener spacing at new fastener
locations.
(c) At existing fastener locations only, it is permitted to make the hole size a maximum of 1/32 inch larger
than the existing diameter. Refer to the fastener code table below. Maintain a minimum 1.7D edge margin.
(d) Remove all nicks, scratches, gouges, burrs, and sharp edges from the repair parts and installed parts.
(e) Apply chemical conversion coating to all bare aluminum surfaces. Refer to SOPM 20-43-03 as an accepted
procedure.
(f) Apply two layers of BMS 10-11, Type 1 primer to all surfaces where chemical conversion coating was
applied. Refer to SOPM 20-41-02 as an accepted procedure.
(g) Apply sealant to all faying surfaces and apply a fillet seal around the edges of the repair. Refer to SOPM
20-50-19 as an accepted procedure.
(h) Maximum clearance between mating parts before fastener installation 0.010 inch. Install shims as neces-
sary. Maximum shim thickness 0.040 inch. Refer to SOPM 20-50-20 as an accepted procedure.
(i) Refer to the fastener code table below.
(j) If required, install a local 7075 aluminum radius filler at each fastener common to the frame flange to seat
the fastener properly. Do not use a continuous radius filler. The filler can be made from the following three
material options: 7075-0 aluminum alloy, or 7075-0 aluminum alloy and heat treated to the T6 condition
after the filler is made.
(k) Apply corrosion inhibiting compound to the repair area. Refer to SOPM 20-41-05 as an accepted procedure.
(l) Maximum clearance between mating parts before fastener installation 0.010 inch. Shim installation is
acceptable to achieve clearance. Maximum shim thickness 0.040 inch. Refer to SOPM 20-50-20 as an
accepted procedure.
(m) Install all fasteners in accordance with 737-600 SRM 51-40-02, 737-700 SRM 51-40-02, 737-700IGW
SRM 51-40-02, 737-800 SRM 51-40-02, 737-800BCF SRM 51-40-02, or 737-900 SRM 51-40-02. Overdrive
all rivet shanks to 1.5D.
FIGURE 16: RIGHT SIDE, STA 907 FRAME, SUPPORT BRACKET ATTACHMENT HOLES AT THE AIR
CONDITIONING EXTRUSION - INSTALL REPAIR PARTS (OPTION 1)
(SHEET 5 OF 7)
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: October 04, 2006
737-25A1544Revision 4 February 15, 2022
149 of 202
BOEING SERVICE BULLETIN 737-25A1544
ALERTALERT

### Page 26

The codes shown below agree with the letter shown in the upper left corner of the fastener symbols in the figure.
NOTESHOLE DIAPART NUMBERNAMECODE
Use when frame gage is
0.056 inch. (a)(b)
0.187 - 0.190BACB30FM6A3, BACC30M6Hi-lok, CollarA
Use when frame gage is
0.071 inch. (a)(b)
0.187 - 0.190BACB30FM6A4, BACC30M6Hi-lok, Collar
Use when frame gage is
0.056 inch. (a)
0.247 - 0.250BACB30NX8K4,
BACC30BH8
Hi-lok, CollarD
Use when frame gage is
0.071 inch. (a)
0.247 - 0.250BACB30NX8K5,
BACC30BH8
Hi-lok, Collar
Use when frame gage is
0.056 inch. (a)(c)
0.200 - 0.203BACB30MC6A4, BACC30X6Hi-lok, CollarE
Use when frame gage is
0.071 inch. (a)(c)
0.200 - 0.203BACB30MC6A5, BACC30X6Hi-lok, Collar
Use when frame gage is
0.056 inch. (a)(d)
0.216 - 0.219BACB30MD6A4,
BACC30AC6
Hi-lok, Collar
Use when frame gage is
0.071 inch. (a)(d)
0.216 - 0.219BACB30MD6A5,
BACC30AC6
Hi-lok, Collar
-0.190 - 0.196BACR15GF6D6RivetF
Use when frame gage is
0.056 inch. (a)(b)(c)
0.200 - 0.203BACB30MC6A3, BACC30X6Hi-lok, CollarG
Use when frame gage is
0.071 inch. (a)(b)(c)(e)
0.200 - 0.203BACB30MC6A4, BACC30X6Hi-lok, Collar
Use when frame gage is
0.056 inch. (a)(b)(d)
0.216 - 0.219BACB30MD6A3,
BACC30AC6
Hi-lok, Collar
Use when frame gage is
0.071 inch. (a)(b)(d)(e)
0.216 - 0.219BACB30MD6A4,
BACC30AC6
Hi-lok, Collar
Use when frame gage is
0.056 inch. (a)(b)
0.187 - 0.190BACB30FM6A2, BACC30M6Hi-lok, CollarH
Use when frame gage is
0.071 inch. (a)(b)
0.187 - 0.190BACB30FM6A3, BACC30M6Hi-lok, Collar
FIGURE 16: RIGHT SIDE, STA 907 FRAME, SUPPORT BRACKET ATTACHMENT HOLES AT THE AIR
CONDITIONING EXTRUSION - INSTALL REPAIR PARTS (OPTION 1)
(SHEET 6 OF 7)
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: October 04, 2006
737-25A1544Revision 4 February 15, 2022
150 of 202
BOEING SERVICE BULLETIN 737-25A1544
ALERTALERT

### Page 27

NOTESHOLE DIAPART NUMBERNAMECODE
Use when frame gage is
0.056 inch. (a)(c)
0.200 - 0.203BACB30MC6A2, BACC30X6Hi-lok, CollarI
Use when frame gage is
0.071 inch. (a)(c)(e)
0.200 - 0.203BACB30MC6A3, BACC30X6Hi-lok, Collar
Use when frame gage is
0.056 inch. (a)(d)
0.216 - 0.219BACB30MD6A2,
BACC30AC6
Hi-lok, Collar
Use when frame gage is
0.071 inch. (a)(d)(e)
0.216 - 0.219BACB30MD6A3,
BACC30AC6
Hi-lok, Collar
Use when frame gage is
.056.
.200 - .203BACB30MC6A7, BACC30X6Hi-lok, CollarJ
Use when frame gage is
.056.
.216 - .219BACB30MD6A7, BACC30X6Hi-lok, Collar
Use when frame gage is
.071.
.200 - .203BACB30MC6A8, BACC30X6Hi-lok, Collar
Use when frame gage is
.071.
.216 - .219BACB30MD6A8,
BACC30AC6
Hi-lok, Collar
(a) Install wet with BMS 5-95 sealant. Refer to SOPM 20-50-19, Corrosion Protection Sealing, Method
2, as an accepted procedure.
(b) If fastener is installed at a location which requires a radius filler, measure build-up to determine grip
length.
(c) This fastener has a 1/64 (first) nominal oversize shank.
(d) This fastener has a 1/32 (second) nominal oversize shank.
(e) Use to install stringer clip on stringer.
FIGURE 16: RIGHT SIDE, STA 907 FRAME, SUPPORT BRACKET ATTACHMENT HOLES AT THE AIR
CONDITIONING EXTRUSION - INSTALL REPAIR PARTS (OPTION 1)
(SHEET 7 OF 7)
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: October 04, 2006
737-25A1544Revision 4 February 15, 2022
151 of 202
BOEING SERVICE BULLETIN 737-25A1544
ALERTALERT

### Page 28 (OCR)

BOEING SERVICE BULLETIN 737-25A1544
ALERT  ALERT
This Figure applies only to: Group 1-4, 6.
STA
907
S-7L
FRAME SHEAR
TIE
SUPPORT
FITTING
STRINGER 4€€  CLIP
S-8L
SUPPORT BRACKET
MAXIMUM  80® ANGLEC
CUT OUT AREA
AND FILLER D
FAILSAFE
CHORD
FRAME
FRAME SHEAR
TIE
S-9L
INBD
STA 907  2293381
FIGURE 17: LEFT SIDE, STA 907 FRAME, SUPPORT BRACKET ATTACHMENT HOLES AT THE AIR
CONDITIONING EXTRUSION - MAKE REPAIR PARTS (OPTION 2)
(SHEET 1 OF 8)
Original Issue: October 04, 2006
Revision 4 February 15, 2022  737-25A1544
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.  152 of 202

### Page 29 (OCR)

BOEING SERVICE BULLETIN 737-25A1544
ALERT  ALERT
DO® ANGLEC
FRAME
FRAME SHEAR TIE
FAILSAFE CHORD
ABOVE AND BELOW THE
CUT OUT AREA
(TYPICAL)
A-A
FWD
2293385
FIGURE 17: LEFT SIDE, STA 907 FRAME, SUPPORT BRACKET ATTACHMENT HOLES AT THE AIR
CONDITIONING EXTRUSION - MAKE REPAIR PARTS (OPTION 2)
(SHEET 2 OF 8)
Original Issue: October 04, 2006
Revision 4 February 15, 2022  737-25A1544
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.  153 of 202

### Page 30 (OCR)

BOEING SERVICE BULLETIN 737-25A1544
ALERT  ALERT
FLANGE RADIUS
FRAME -
800 ANGLEC
CUT OUT AREA A € O
AND FILLER D
„OUTBOARD HOLE
• FRAME SHEAR TIE
FAILSAFE CHORD
FOR CUT OUT ONLY AT INBOARD HOLE
(BELOW S-8L)
B-B
FWD
2293390
FIGURE 17: LEFT SIDE, STA 907 FRAME, SUPPORT BRACKET ATTACHMENT HOLES AT THE AIR
CONDITIONING EXTRUSION - MAKE REPAIR PARTS (OPTION 2)
(SHEET 3 OF 8)
Original Issue: October 04, 2006
Revision 4 February 15, 2022  737-25A1544
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.  154 of 202

### Page 31 (OCR)

BOEING SERVICE BULLETIN 737-25A1544
ALERT  ALERT
FRAME ~  8OO ANGLEC
INBOARD HOLE
CUT OUT AREA (45€
AND FILLER D
FAILSAFE CHORD  FRAME SHEAR TIE
FOR CUT OUT ONLY AT OUTBOARD HOLE
(BELOW S-8L)
B-B
FWD
2293393
FIGURE 17: LEFT SIDE, STA 907 FRAME, SUPPORT BRACKET ATTACHMENT HOLES AT THE AIR
CONDITIONING EXTRUSION - MAKE REPAIR PARTS (OPTION 2)
(SHEET 4 OF 8)
Original Issue: October 04, 2006
Revision 4 February 15, 2022  737-25A1544
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.  155 of 202

### Page 32 (OCR)

BOEING SERVICE BULLETIN 737-25A1544
ALERT  ALERT
FLANGE RADIUS
FRAME •  800 ANGLES
CUT OUT AREA 1€ O
AND FILLER D
FAILSAFE CHORD  FRAME SHEAR TIE
FOR CUT OUT AT INBOARD AND OUTBOARD HOLE
(BELOW S-8L)
B-B
FWD
FIGURE 17: LEFT SIDE, STA 907 FRAME, SUPPORT BRACKET ATTACHMENT HOLES AT THE AIR
CONDITIONING EXTRUSION - MAKE REPAIR PARTS (OPTION 2)
(SHEET 5 OF 8)
Original Issue: October 04, 2006
Revision 4 February 15, 2022  737-25A1544
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.  156 of 202

### Page 33 (OCR)

BOEING SERVICE BULLETIN 737-25A1544
ALERT  ALERT
23 ANGLE C
CUT OUT AREA (4
AND FILLER D
_ OUTBOARD HOLE
• FRAME
FRAME SHEAR TIE
FAILSAFE CHORD
FOR CUT OUT ONLY AT INBOARL
HOLE AND INNER FLANGE
(BELOW S-8L)
B-B
WD
2293396
FIGURE 17: LEFT SIDE, STA 907 FRAME, SUPPORT BRACKET ATTACHMENT HOLES AT THE AIR
CONDITIONING EXTRUSION - MAKE REPAIR PARTS (OPTION 2)
(SHEET 6 OF 8)
Original Issue: October 04, 2006
Revision 4 February 15, 2022  737-25A1544
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.  157 of 202

### Page 34 (OCR)

BOEING SERVICE BULLETIN 737-25A1544
ALERT  ALERT
80® ANGLEC
CUT OUT AREA +5 €  AND FILLER D
• FRAME SHEAR TIE
FAILSAFE CHORD
FOR CUT OUT ACROSS ENTIRE SECTION
(BELOW S-8L)
B-B
FWD
2293397
FIGURE 17: LEFT SIDE, STA 907 FRAME, SUPPORT BRACKET ATTACHMENT HOLES AT THE AIR
CONDITIONING EXTRUSION - MAKE REPAIR PARTS (OPTION 2)
(SHEET 7 OF 8)
Original Issue: October 04, 2006
Revision 4 February 15, 2022  737-25A1544
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.  158 of 202

### Page 35

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for one body frame.
More DataQtyIdentificationNameTaskStep
(a)(b)(e)1ANGLE CREPAIR ANGLE CMake1
From the annealed
condition to the T6
condition after form-
ing.
1ANGLE CREPAIR ANGLE CHeat Treat2
(c)1ANGLE CREPAIR ANGLE CInspect3
(c)(d)(e)1FILLER DFILLERMake4
(f)-TYPE 2, CLASS ACHEMICAL CONVER-
SION COATING
Apply5
(g)-BMS 10-11, TYPE 1PRIMERApply6
(a) If the existing frame web is 0.056 inch thick, make Repair Angle C from 0.063 inch thick 7075-0 clad sheet
with minimum bend radius of 0.12 inch. If the existing frame web is 0.071 inch thick, make Repair Angle
C from 0.080 inch thick 7075-0 clad sheet with minimum bend radius of 0.19 inch. Form the repair angles
in the annealed condition to match the contour of the frame in accordance with 737-600 SRM 51-30-01,
737-700 SRM 51-30-01, 737-700IGW (BBJ) SRM 51-30-01, 737-800 SRM 51-30-01, 737-800BCF SRM
51-30-01 or 737-900 SRM 51-30-01.
(b) Make sure that the length of the repair angle is sufficient to have a minimum of five rows of fasteners
common to the frame inboard flange and a minimum of five rows of fasteners common to the frame web
above and below the cut out area.
(c) Do a dye penetrant inspection of the bend radius to make sure there are no cracks. Refer to SOPM 20-
20-02 as an accepted procedure.
(d) Make Filler D from 7075-T6 clad sheet, or from 7075-0 clad sheet if it needs to be formed, that has the
same thickness as the existing frame. Filler D can be formed with minimum bend radius of 0.19 inch.
Form in the annealed condition to match the contour of the frame in accordance with 737-600 SRM 51-
30-01, 737-700 SRM 51-30-01, 737-700IGW SRM 51-30-01, 737-800 SRM 51-30-01, 737-800BCF SRM
51-30-01 or 737-900 SRM 51-30-01, and heat treat to T6.
(e) Maintain a 0.50 inch minimum corner radius. Maintain a minimum 2D edge margin. Maintain 63 microinches
Ra or better surface finish on all cut surfaces. Break sharps edges. Make sure that the repair parts do
not end common to the stringer clip. Extending the repair parts one row of fasteners beyond the stringer
clip is acceptable.
(f) Apply chemical conversion coating to all bare aluminum surfaces. Refer to SOPM 20-43-03 as an accepted
procedure.
(g) Apply two layers of BMS 10-11, Type 1 primer to all surfaces where chemical conversion coating was
applied. Refer to SOPM 20-41-02 as an accepted procedure.
FIGURE 17: LEFT SIDE, STA 907 FRAME, SUPPORT BRACKET ATTACHMENT HOLES AT THE AIR
CONDITIONING EXTRUSION - MAKE REPAIR PARTS (OPTION 2)
(SHEET 8 OF 8)
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: October 04, 2006
737-25A1544Revision 4 February 15, 2022
159 of 202
BOEING SERVICE BULLETIN 737-25A1544
ALERTALERT

### Page 36 (OCR)

BOEING SERVICE BULLETIN 737-25A1544
ALERT  ALERT
This Figure applies only to: Group 1-4, 6.
STA
907
- S-7R
FRAME SHEAR
TIE
SUPPORT
FITTING
STRINGER
CLIP
S-8R
SUPPORT BRACKET
MAXIMUM
ANGLEC DOO  5)  CUT OUT AREA
AND FILLER D
FRAME
FRAME SHEAR
TIE
• S-9R
INBD
STA 907  2910430
FIGURE 18: RIGHT SIDE, STA 907 FRAME, SUPPORT BRACKET ATTACHMENT HOLES AT THE AIR
CONDITIONING EXTRUSION - MAKE REPAIR PARTS (OPTION 2)
(SHEET 1 OF 8)
Original Issue: October 04, 2006
Revision 4 February 15, 2022  Export Controlled ECCN: 9E991  737-25A1544
Copyright © Unpublished Work - See page 1 for details.  160 of 202

### Page 37 (OCR)

BOEING SERVICE BULLETIN 737-25A1544
ALERT  ALERT
ANGLE C OOO
FRAME
FRAME SHEAR TIE
FAILSAFE CHORD
ABOVE AND BELOW THE CUT
OUT AREA
(TYPICAL)
A-A
2293694
FIGURE 18: RIGHT SIDE, STA 907 FRAME, SUPPORT BRACKET ATTACHMENT HOLES AT THE AIR
CONDITIONING EXTRUSION - MAKE REPAIR PARTS (OPTION 2)
(SHEET 2 OF 8)
Original Issue: October 04, 2006
Revision 4 February 15, 2022  Export Controlled ECCN: 9E991  737-25A1544
Copyright © Unpublished Work - See page 1 for details.  161 of 202

### Page 38 (OCR)

BOEING SERVICE BULLETIN 737-25A1544
ALERT  ALERT
FLANGE RADIUS
— FRAME
ANGLE COZE
45O CUT OUT AREA  AND FILLER D
OUTBOARD HOLE
FRAME SHEAR TIE
FAILSAFE CHORD
FOR CUT OUT ONLY AT INBOARD HOLE
(BELOW S-8R)
B-B
2293696
FIGURE 18: RIGHT SIDE, STA 907 FRAME, SUPPORT BRACKET ATTACHMENT HOLES AT THE AIR
CONDITIONING EXTRUSION - MAKE REPAIR PARTS (OPTION 2)
(SHEET 3 OF 8)
Original Issue: October 04, 2006
Revision 4 February 15, 2022  Export Controlled ECCN: 9E991  737-25A1544
Copyright © Unpublished Work - See page 1 for details.  162 of 202

### Page 39 (OCR)

BOEING SERVICE BULLETIN 737-25A1544
ALERT  ALERT
ANGLEC OOO  — FRAME
INBOARD HOLE
5) 6) CUT OUT AREA  AND FILLER L
FRAME SHEAR TIE
FAILSAFE CHORD
FOR CUT OUT ONLY AT OUTBOARD HOLE
(BELOW S-8R)
B-B
2293697
FIGURE 18: RIGHT SIDE, STA 907 FRAME, SUPPORT BRACKET ATTACHMENT HOLES AT THE AIR
CONDITIONING EXTRUSION - MAKE REPAIR PARTS (OPTION 2)
(SHEET 4 OF 8)
Original Issue: October 04, 2006
Revision 4 February 15, 2022  Export Controlled ECCN: 9E991  737-25A1544
Copyright © Unpublished Work - See page 1 for details.  163 of 202

### Page 40 (OCR)

BOEING SERVICE BULLETIN 737-25A1544
ALERT  ALERT
FLANGE RADIUS
ANGLE COZE  I TRONE
45O CUT OUT AREA  AND FILLER D
J
FRAME SHEAR TIE
FAILSAFE CHORD
FOR CUT OUT AT INBOARD AND OUTBOARD HOLE
(BELOW S-8R)
B-B
2293700
FIGURE 18: RIGHT SIDE, STA 907 FRAME, SUPPORT BRACKET ATTACHMENT HOLES AT THE AIR
CONDITIONING EXTRUSION - MAKE REPAIR PARTS (OPTION 2)
(SHEET 5 OF 8)
Original Issue: October 04, 2006
Revision 4 February 15, 2022  Export Controlled ECCN: 9E991  737-25A1544
Copyright © Unpublished Work - See page 1 for details.  164 of 202

### Page 41 (OCR)

BOEING SERVICE BULLETIN 737-25A1544
ALERT  ALERT
ANGLE C OOO
SO AND FILLERBA
OUTBOARD HOLE
FRAME
FRAME SHEAR TIE
FAILSAFE CHORD
FOR CUT OUT ONLY AT INBOARD
HOLE AND INNER FLANGE
(BELOW S-8R)
B-B
2293701
FIGURE 18: RIGHT SIDE, STA 907 FRAME, SUPPORT BRACKET ATTACHMENT HOLES AT THE AIR
CONDITIONING EXTRUSION - MAKE REPAIR PARTS (OPTION 2)
(SHEET 6 OF 8)
Original Issue: October 04, 2006
Revision 4 February 15, 2022  Export Controlled ECCN: 9E991  737-25A1544
Copyright © Unpublished Work - See page 1 for details.  165 of 202

### Page 42 (OCR)

BOEING SERVICE BULLETIN 737-25A1544
ALERT  ALERT
ANGLE C OOO
AEO AND FILL AREA  AND FILLER D
FRAME SHEAR TIE
FAILSAFE CHORD
FOR CUT OUT ACROSS ENTIRE SECTION
(BELOW S-8R)
B-B
2293702
FIGURE 18: RIGHT SIDE, STA 907 FRAME, SUPPORT BRACKET ATTACHMENT HOLES AT THE AIR
CONDITIONING EXTRUSION - MAKE REPAIR PARTS (OPTION 2)
(SHEET 7 OF 8)
Original Issue: October 04, 2006
Revision 4 February 15, 2022  Export Controlled ECCN: 9E991  737-25A1544
Copyright © Unpublished Work - See page 1 for details.  166 of 202

### Page 43

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for one body frame.
More DataQtyIdentificationNameTaskStep
(a)(b)(e)1ANGLE CREPAIR ANGLE CMake1
From the annealed
condition to the T6
condition after form-
ing.
1ANGLE CREPAIR ANGLE CHeat Treat2
(c)1ANGLE CREPAIR ANGLE CInspect3
(c)(d)(e)1FILLER DFILLERMake4
(f)-TYPE 2, CLASS ACHEMICAL CONVER-
SION COATING
Apply5
(g)-BMS 10-11, TYPE 1PRIMERApply6
(a) If the existing frame web is 0.056 inch thick, make Repair Angle C from 0.063 inch thick 7075-0 clad sheet
with minimum bend radius of 0.12 inch. If the existing frame web is 0.071 inch thick, make Repair Angle
C from 0.080 inch thick 7075-0 clad sheet with minimum bend radius of 0.19 inch. Form the repair angles
in the annealed condition to match the contour of the frame in accordance with 737-600 SRM 51-30-01,
737-700 SRM 51-30-01, 737-700IGW (BBJ) SRM 51-30-01, 737-800 SRM 51-30-01, 737-800BCF SRM
51-30-01 or 737-900 SRM 51-30-01.
(b) Make sure that the length of the repair angle is sufficient to have a minimum of five rows of fasteners
common to the frame inboard flange and a minimum of five rows of fasteners common to the frame web
above and below the cut out area.
(c) Do a dye penetrant inspection of the bend radius to make sure there are no cracks. Refer to SOPM 20-
20-02 as an accepted procedure.
(d) Make Filler D from 7075-T6 clad sheet, or from 7075-0 clad sheet if it needs to be formed, that has the
same thickness as the existing frame. Filler D can be formed with minimum bend radius of 0.19 inch.
Form in the annealed condition to match the contour of the frame in accordance with 737-600 SRM 51-
30-01, 737-700 SRM 51-30-01, 737-700IGW SRM 51-30-01, 737-800 SRM 51-30-01, 737-800BCF SRM
51-30-01 or 737-900 SRM 51-30-01, and heat treat to T6.
(e) Maintain a 0.50 inch minimum corner radius. Maintain a minimum 2D edge margin. Maintain 63 microinches
Ra or better surface finish on all cut surfaces. Break sharp edges. Make sure that the repair parts do not
end common to the stringer clip. Extending the repair parts one row of fasteners beyond the stringer clip
is acceptable.
(f) Apply chemical conversion coating to all bare aluminum surfaces. Refer to SOPM 20-43-03 as an accepted
procedure.
(g) Apply two layers of BMS 10-11, Type 1 primer to all surfaces where chemical conversion coating was
applied. Refer to SOPM 20-41-02 as an accepted procedure.
FIGURE 18: RIGHT SIDE, STA 907 FRAME, SUPPORT BRACKET ATTACHMENT HOLES AT THE AIR
CONDITIONING EXTRUSION - MAKE REPAIR PARTS (OPTION 2)
(SHEET 8 OF 8)
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: October 04, 2006
737-25A1544Revision 4 February 15, 2022
167 of 202
BOEING SERVICE BULLETIN 737-25A1544
ALERTALERT

### Page 44 (OCR)

BOEING SERVICE BULLETIN 737-25A1544
ALERT  ALERT
This Figure applies only to: Group 1-4, 6.
STA
907
S-7L
FRAME
SHEAR TIE
SUPPORT
FITTING
16 LOCATIONS
(TYPICAL)
SUPPORT
STRINGER  CLIP  GL  BRACKET
S-8L-
234 ANGLE C
CUT OUT AREA (
AND FILLER D
(TYPICAL)  FRAME
FAILSAFE
CHORD
FRAME SHEAR
TIE
S-9L
STA 907  INBD  2293419
FIGURE 19: LEFT SIDE, STA 907 FRAME, SUPPORT BRACKET ATTACHMENT HOLES AT THE AIR
CONDITIONING EXTRUSION - INSTALL REPAIR PARTS (OPTION 2)
(SHEET 1 OF 7)
Original Issue: October 04, 2006
Revision 4 February 15, 2022  737-25A1544
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.  168 of 202

### Page 45 (OCR)

BOEING SERVICE BULLETIN 737-25A1544
ALERT  ALERT
S-8L
INBD
2293420
FIGURE 19: LEFT SIDE, STA 907 FRAME, SUPPORT BRACKET ATTACHMENT HOLES AT THE AIR
CONDITIONING EXTRUSION - INSTALL REPAIR PARTS (OPTION 2)
(SHEET 2 OF 7)
Original Issue: October 04, 2006
Revision 4 February 15, 2022  737-25A1544
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.  169 of 202

### Page 46 (OCR)

BOEING SERVICE BULLETIN 737-25A1544
ALERT  ALERT
STRINGER
, ANGLE C
FRAME
STA _
907
A-A
_ STRINGER
STA
907
FRAME
ANGLE C
B-B  2459199
FIGURE 19: LEFT SIDE, STA 907 FRAME, SUPPORT BRACKET ATTACHMENT HOLES AT THE AIR
CONDITIONING EXTRUSION - INSTALL REPAIR PARTS (OPTION 2)
(SHEET 3 OF 7)
Original Issue: October 04, 2006
Revision 4 February 15, 2022  Export Controlled ECCN: 9E991  737-25A1544
Copyright © Unpublished Work - See page 1 for details.  170 of 202

### Page 47 (OCR)

BOEING SERVICE BULLETIN 737-25A1544
ALERT  ALERT
STA 907
S-7L -
===:
===:
S-8L -
'==!
S-9L-
FWD  2459201
C-C
FIGURE 19: LEFT SIDE, STA 907 FRAME, SUPPORT BRACKET ATTACHMENT HOLES AT THE AIR
CONDITIONING EXTRUSION - INSTALL REPAIR PARTS (OPTION 2)
(SHEET 4 OF 7)
Original Issue: October 04, 2006
Revision 4 February 15, 2022  737-25A1544
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.  171 of 202

### Page 48

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for one body frame.
More DataQtyIdentificationNameTaskStep
-1FILLER DFILLERPut / Hold1
-1ANGLE CREPAIR ANGLE CPut / Hold
-2147A1007-( )FRAME SHEAR TIEPut / Hold
-1147A3500-13STRINGER CLIPPut / Hold
-1412A3210-( )SUPPORT BRACKETPut / Hold
-1147A9100-()SUPPORT FITTINGPut / Hold
(a)(b)(c)--HOLEDrill
-1FILLER DFILLERRemove / Keep2
-1ANGLE CREPAIR ANGLE CRemove / Keep
-2147A1007-( )FRAME SHEAR TIERemove / Keep
-1147A3500-13STRINGER CLIPRemove / Keep
-1412A3210-( )SUPPORT BRACKETRemove / Keep
(d)--PARTSDeburr
(e)-TYPE 2, CLASS ACHEMICAL CONVER-
SION COATING
Apply3
(f)-BMS 10-11, TYPE 1PRIMERApply
(g)-BMS 5-95, CLASS B-
1/2, B-2
SEALANTApply4
(h)1FILLER DFILLERInstall (New)
(h)1ANGLE CREPAIR ANGLE CInstall (New)
(j)--RADIUS FILLERInstall (New)
(i)--FASTENERInstall (New)
(h)1147A3500-13STRINGER CLIPInstall (New)5
(i)--FASTENERInstall (New)
(h)2147A1007-( )FRAME SHEAR TIEInstall (New)6
(i)--FASTENERInstall (New)
(h)1412A3210-( )SUPPORT BRACKETInstall (Kept)7
1BACF3F008G008NNFILLERInstall (Kept)
(i)(l)2-FASTENERInstall (New)
FIGURE 19: LEFT SIDE, STA 907 FRAME, SUPPORT BRACKET ATTACHMENT HOLES AT THE AIR
CONDITIONING EXTRUSION - INSTALL REPAIR PARTS (OPTION 2)
(SHEET 5 OF 7)
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: October 04, 2006
737-25A1544Revision 4 February 15, 2022
172 of 202
BOEING SERVICE BULLETIN 737-25A1544
ALERTALERT

### Page 49

More DataQtyIdentificationNameTaskStep
(m)1147A9100-()SUPPORT FITTINGInstall (Kept)8
(l)2-FASTENERInstall (New)
(k)-BMS 3-29 (BMS 3-23
or BMS 3-35 optional)
CORROSION INHIBIT-
ING COMPOUND
Apply9
(a) Drill fastener holes in Filler B, Filler C, Repair Angle C, frame shear ties, stringer clip, support bracket,
support fitting and frame.
(b) Stagger fasteners to maintain a minimum 2D edge margin and 4D-6D fastener spacing at new fastener
locations.
(c) At existing fastener locations only, it is permitted to make the hole size a maximum of 1/32 inch larger
than the existing diameter. Refer to the fastener code table below. Maintain a minimum 1.7D edge margin.
(d) Remove all nicks, scratches, gouges, burrs, and sharp edges from the repair parts and installed parts.
(e) Apply chemical conversion coating to all bare aluminum surfaces. Refer to SOPM 20-43-03 as an accepted
procedure.
(f) Apply two layers of BMS 10-11, Type 1 primer to all surfaces where chemical conversion coating was
applied. Refer to SOPM 20-41-02 as an accepted procedure.
(g) Apply sealant to all faying surfaces and apply a fillet seal around the edges of the repair. Refer to SOPM
20-50-19 as an accepted procedure.
(h) Maximum clearance between mating parts before fastener installation 0.010 inch. Install shims as neces-
sary. Maximum shim thickness 0.040 inch. Refer to SOPM 20-50-20 as an accepted procedure.
(i) Refer to the fastener code table below.
(j) If required, install a local 7075 aluminum radius filler at each fastener common to the frame flange to seat
the fastener properly. Do not use a continuous radius filler. The filler can be made from the following three
material options: 7075-0 aluminum alloy, 7075-T6 aluminum alloy, or 7075-0 aluminum alloy and heat
treated to the T6 condition after the filler is made.
(k) Apply corrosion inhibiting compound to the repair area. Refer to SOPM 20-41-05 as an accepted procedure.
(l) Install all fasteners in accordance with 737-600 SRM 51-40-02, 737-700 SRM 51-40-02, 737-700IGW
SRM 51-40-02, 737-800 SRM 51-40-02, 737-800BCF SRM 51-40-02, or 737-900 SRM 51-40-02. Overdrive
all rivet shanks to 1.5D.
(m) Maximum clearance between mating parts before fastener installation 0.010 inch. Install shims as neces-
sary. Maximum shim thickness 0.040 inch. Refer to SOPM 20-50-20 as an accepted procedure.
FIGURE 19: LEFT SIDE, STA 907 FRAME, SUPPORT BRACKET ATTACHMENT HOLES AT THE AIR
CONDITIONING EXTRUSION - INSTALL REPAIR PARTS (OPTION 2)
(SHEET 6 OF 7)
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: October 04, 2006
737-25A1544Revision 4 February 15, 2022
173 of 202
BOEING SERVICE BULLETIN 737-25A1544
ALERTALERT

### Page 50

The codes shown below agree with the letter shown in the upper left corner of the fastener symbols in the figure.
NOTESHOLE DIAPART NUMBERNAMECODE
Use to install stringer clip
on stringer. (a)
0.187 - 0.190BACB30FM6A2, BACC30M6Hi-lok, CollarA
Use when frame gage is
0.056 inch. (a)(b)
0.187 - 0.190BACB30FM6A3, BACC30M6Hi-lok, Collar
Use when frame gage is
0.071 inch. (a)(b)
0.187 - 0.190BACB30FM6A4, BACC30M6Hi-lok, Collar
Use when frame gage is
0.056 inch. (a)
0.247 - 0.250BACB30NX8K4,
BACC30BH8
Hi-lok, CollarD
Use when frame gage is
0.071 inch. (a)
0.247 - 0.250BACB30NX8K5,
BACC30BH8
Hi-lok, Collar
Use when frame gage is
0.056 inch. (a)(c)
0.200 - 0.203BACB30MC6A4, BACC30X6Hi-lok, CollarE
Use when frame gage is
0.071 inch. (a)(c)
0.200 - 0.203BACB30MC6A5, BACC30X6Hi-lok, Collar
Use when frame gage is
0.056 inch. (a)(d)
0.216 - 0.219BACB30MD6A4,
BACC30AC6
Hi-lok, Collar
Use when frame gage is
0.071 inch. (a)(d)
0.216 - 0.219BACB30MD6A5,
BACC30AC6
Hi-lok, Collar
-0.190 - 0.196BACR15GF6D6RivetF
Use when frame gage is
0.056 inch. (a)(c)
0.200 - 0.203BACB30MC6A3, BACC30X6Hi-lok, CollarG
Use when frame gage is
0.071 inch. (a)(c)
0.200 - 0.203BACB30MC6A4, BACC30X6Hi-lok, Collar
Use when frame gage is
0.056 inch. (a)(d)
0.216 - 0.219BACB30MD6A3,
BACC30AC6
Hi-lok, Collar
Use when frame gage is
0.071 inch. (a)(d)
0.216 - 0.219BACB30MD6A4,
BACC30AC6
Hi-lok, Collar
(a) Install wet with BMS 5-95 sealant. Refer to SOPM 20-50-19, Corrosion Protection Sealing, Method
2, as an accepted procedure.
(b) If fastener is installed at a location which requires a radius filler, measure build-up to determine grip
length.
(c) This fastener has a 1/64 (first) nominal oversize shank.
(d) This fastener has a 1/32 (second) nominal oversize shank.
FIGURE 19: LEFT SIDE, STA 907 FRAME, SUPPORT BRACKET ATTACHMENT HOLES AT THE AIR
CONDITIONING EXTRUSION - INSTALL REPAIR PARTS (OPTION 2)
(SHEET 7 OF 7)
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: October 04, 2006
737-25A1544Revision 4 February 15, 2022
174 of 202
BOEING SERVICE BULLETIN 737-25A1544
ALERTALERT

### Page 51 (OCR)

BOEING SERVICE BULLETIN 737-25A1544
ALERT  ALERT
This Figure applies only to: Group 1-4, 6.
STA
907
- S-7R
B
FRAME
SHEAR TIE
SUPPORT
4 006  FITTING
14 LOCATIONS
(TYPICAL)
SUPPORT
BRACKET  STRINGER
CLIP
* - S-8R
DE34
ANGLE C
CUT OUT AREA
AND FILLER C
(TYPICAL)
FRAME
FRAME SHEAR
TIE
FILLER B 123C
FAILSAFE ~
CHORD  B
- S-9R
INBD  2293606
STA 907
FIGURE 20: RIGHT SIDE, STA 907 FRAME, SUPPORT BRACKET ATTACHMENT HOLES AT THE AIR
CONDITIONING EXTRUSION - INSTALL REPAIR PARTS (OPTION 2)
(SHEET 1 OF 6)
Original Issue: October 04, 2006
Revision 4 February 15, 2022  737-25A1544
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.  175 of 202

### Page 52 (OCR)

BOEING SERVICE BULLETIN 737-25A1544
ALERT  ALERT
S-8R
STRINGER
ANGLE C
•FRAME
A-A  2293605
FIGURE 20: RIGHT SIDE, STA 907 FRAME, SUPPORT BRACKET ATTACHMENT HOLES AT THE AIR
CONDITIONING EXTRUSION - INSTALL REPAIR PARTS (OPTION 2)
(SHEET 2 OF 6)
Original Issue: October 04, 2006
Revision 4 February 15, 2022  Export Controlled ECCN: 9E991  737-25A1544
Copyright © Unpublished Work - See page 1 for details.  176 of 202

### Page 53 (OCR)

BOEING SERVICE BULLETIN 737-25A1544
ALERT  ALERT
STA 907
- S-7R
- S-8R
- S-9R
FWD  2459205
B-B
FIGURE 20: RIGHT SIDE, STA 907 FRAME, SUPPORT BRACKET ATTACHMENT HOLES AT THE AIR
CONDITIONING EXTRUSION - INSTALL REPAIR PARTS (OPTION 2)
(SHEET 3 OF 6)
Original Issue: October 04, 2006
Revision 4 February 15, 2022  737-25A1544
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.  177 of 202

### Page 54

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for one body frame.
More DataQtyIdentificationNameTaskStep
-1FILLER DFILLERPut / Hold1
-1ANGLE CREPAIR ANGLE CPut / Hold
-2147A1007-( )FRAME SHEAR TIEPut / Hold
-1147A3500-( )STRINGER CLIPPut / Hold
-1412A3210-( )SUPPORT BRACKETPut / Hold
-1147A9100-()SUPPORT FITTINGPut / Hold
(a)(b)(c)--HOLEDrill
-1FILLER DFILLERRemove / Keep2
-1ANGLE CREPAIR ANGLE CRemove / Keep
-2147A1007-( )FRAME SHEAR TIERemove / Keep
-1147A3500-( )STRINGER CLIPRemove / Keep
-1412A3210-( )SUPPORT BRACKETRemove / Keep
(d)--PARTSDeburr
(e)-TYPE 2, CLASS ACHEMICAL CONVER-
SION COATING
Apply3
(f)-BMS 10-11, TYPE 1PRIMERApply
(g)-BMS 5-95, CLASS B-
1/2, B-2
SEALANTApply4
(h)1FILLER DFILLERInstall (New)
(h)1ANGLE CREPAIR ANGLE CInstall (New)
(j)--RADIUS FILLERInstall (New)
(i)--FASTENERInstall (New)
(h)1147A3500-( )STRINGER CLIPInstall (New)5
(i)--FASTENERInstall (New)
(h)2147A1007-( )FRAME SHEAR TIEInstall (New)6
(i)--FASTENERInstall (New)
(h)1412A3210-( )SUPPORT BRACKETInstall (Kept)7
1BACF3F008G008NNFILLERInstall (Kept)
(i)(l)2-FASTENERInstall (New)
FIGURE 20: RIGHT SIDE, STA 907 FRAME, SUPPORT BRACKET ATTACHMENT HOLES AT THE AIR
CONDITIONING EXTRUSION - INSTALL REPAIR PARTS (OPTION 2)
(SHEET 4 OF 6)
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: October 04, 2006
737-25A1544Revision 4 February 15, 2022
178 of 202
BOEING SERVICE BULLETIN 737-25A1544
ALERTALERT

### Page 55

More DataQtyIdentificationNameTaskStep
(m)1147A9100-()SUPPORT FITTINGInstall (Kept)8
(l)2-FASTENERInstall (New)
(k)-BMS 3-29 (BMS 3-23
or BMS 3-35 optional)
CORROSION INHIBIT-
ING COMPOUND
Apply9
(a) Drill fastener holes in Filler B, Filler C, Repair Angle C, frame shear ties, stringer clip, support bracket,
support fitting and frame.
(b) Stagger fasteners to maintain a minimum 2D edge margin and 4D-6D fastener spacing at new fastener
locations.
(c) At existing fastener locations only, it is permitted to make the hole size a maximum of 1/32 inch larger
than the existing diameter. Refer to the fastener code table below. Maintain a minimum 1.7D edge margin.
(d) Remove all nicks, scratches, gouges, burrs, and sharp edges from the repair parts and installed parts.
(e) Apply chemical conversion coating to all bare aluminum surfaces. Refer to SOPM 20-43-03 as an accepted
procedure.
(f) Apply two layers of BMS 10-11, Type 1 primer to all surfaces where chemical conversion coating was
applied. Refer to SOPM 20-41-02 as an accepted procedure.
(g) Apply sealant to all faying surfaces and apply a fillet seal around the edges of the repair. Refer to SOPM
20-50-19 as an accepted procedure.
(h) Maximum clearance between mating parts before fastener installation 0.010 inch. Install shims as neces-
sary. Maximum shim thickness 0.040 inch. Refer to SOPM 20-50-20 as an accepted procedure.
(i) Refer to the fastener code table below.
(j) If required, install a local 7075 aluminum radius filler at each fastener common to the frame flange to seat
the fastener properly. Do not use a continuous radius filler. The filler can be made from the following three
material options: 7075-0 aluminum alloy, 7075-T6 aluminum alloy, or 7075-0 aluminum alloy and heat
treated to the T6 condition after the filler is made.
(k) Apply corrosion inhibiting compound to the repair area. Refer to SOPM 20-41-05 as an accepted procedure.
(l) Install all fasteners in accordance with 737-600 SRM 51-40-02, 737-700 SRM 51-40-02, 737-700IGW
SRM 51-40-02, 737-800 SRM 51-40-02, 737-800BCF SRM 51-40-02, or 737-900 SRM 51-40-02. Overdrive
all rivet shanks to 1.5D.
(m) Maximum clearance between mating parts before fastener installation 0.010 inch. Install shims as neces-
sary. Maximum shim thickness 0.040 inch. Refer to SOPM 20-50-20 as an accepted procedure.
The codes shown below agree with the letter shown in the upper left corner of the fastener symbols in the figure.
NOTESHOLE DIAPART NUMBERNAMECODE
Use when frame gage is
0.056 inch. (a)(b)
0.187 - 0.190BACB30FM6A3, BACC30M6Hi-lok, CollarA
Use when frame gage is
0.071 inch. (a)(b)
0.187 - 0.190BACB30FM6A4, BACC30M6Hi-lok, Collar
FIGURE 20: RIGHT SIDE, STA 907 FRAME, SUPPORT BRACKET ATTACHMENT HOLES AT THE AIR
CONDITIONING EXTRUSION - INSTALL REPAIR PARTS (OPTION 2)
(SHEET 5 OF 6)
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: October 04, 2006
737-25A1544Revision 4 February 15, 2022
179 of 202
BOEING SERVICE BULLETIN 737-25A1544
ALERTALERT

### Page 56

NOTESHOLE DIAPART NUMBERNAMECODE
Use when frame gage is
0.056 inch. (a)
0.247 - 0.250BACB30NX8K4,
BACC30BH8
Hi-lok, CollarD
Use when frame gage is
0.071 inch. (a)
0.247 - 0.250BACB30NX8K5,
BACC30BH8
Hi-lok, Collar
Use when frame gage is
0.056 inch. (a)(c)
0.200 - 0.203BACB30MC6A4, BACC30X6Hi-lok, CollarE
Use when frame gage is
0.071 inch. (a)(c)
0.200 - 0.203BACB30MC6A5, BACC30X6Hi-lok, Collar
Use when frame gage is
0.056 inch. (a)(d)
0.216 - 0.219BACB30MD6A4,
BACC30AC6
Hi-lok, Collar
Use when frame gage is
0.071 inch. (a)(d)
0.216 - 0.219BACB30MD6A5,
BACC30AC6
Hi-lok, Collar
-0.190 - 0.196BACR15GF6D6RivetF
Use when frame gage is
0.056 inch. (a)(c)
0.200 - 0.203BACB30MC6A3, BACC30X6Hi-lok, CollarG
Use when frame gage is
0.071 inch. (a)(c)(e)
0.200 - 0.203BACB30MC6A4, BACC30X6Hi-lok, Collar
Use when frame gage is
0.056 inch. (a)(d)
0.216 - 0.219BACB30MD6A3,
BACC30AC6
Hi-lok, Collar
Use when frame gage is
0.071 inch. (a)(d)(e)
0.216 - 0.219BACB30MD6A4,
BACC30AC6
Hi-lok, Collar
(a) Install wet with BMS 5-95 sealant. Refer to SOPM 20-50-19, Corrosion Protection Sealing, Method
2, as an accepted procedure.
(b) If fastener is installed at a location which requires a radius filler, measure build-up to determine grip
length.
(c) This fastener has a 1/64 (first) nominal oversize shank.
(d) This fastener has a 1/32 (second) nominal oversize shank.
(e) Use to install stringer clip on stringer.
FIGURE 20: RIGHT SIDE, STA 907 FRAME, SUPPORT BRACKET ATTACHMENT HOLES AT THE AIR
CONDITIONING EXTRUSION - INSTALL REPAIR PARTS (OPTION 2)
(SHEET 6 OF 6)
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: October 04, 2006
737-25A1544Revision 4 February 15, 2022
180 of 202
BOEING SERVICE BULLETIN 737-25A1544
ALERTALERT

### Page 57 (OCR)

BOEING SERVICE BULLETIN 737-25A1544
ALERT  ALERT
STA
360
STA
887
ANGLE E
1300U1213
(12 13)
7 LOCATIONS A
(TYPICAL)
2 2 LOCATIONS
S-8
STRINGER
CLIP
5 LOCATIONS
(TYPICAL)
FRAME G-
8 LOCATIONS A  (TYPICAL)  X10
11211
SUPPORT
BRACKET
SIPINGER F  A  6 LOCATIONS
(TYPICAL)
2) 2 LOCATIONS
TYPICAL
INBD  2469281
FIGURE 21: STA 360 THRU STA 887, Z-SECTION FRAME, SUPPORT BRACKET ATTACHMENT HOLES
AT THE AIR CONDITIONING EXTRUSION - FULL FRAME SECTION REPAIR
(SHEET 1 OF 5)
Original Issue: October 04, 2006
Revision 4 February 15, 2022  737-25A1544
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.  181 of 202

### Page 58 (OCR)

BOEING SERVICE BULLETIN 737-25A1544
ALERT  ALERT
1390U113
ANGLE E
130D112  13)
ANGLE D
FRAME  MINIMUM 2D EDGE
MARGIN (TYPICAL)
A-A
4D-6D  ANGLE E
(TYPICAL)
ANGLE D
MINIMUM 2D EDGE
MARGIN (TYPICAL)
B-B  FWD  2469282
FIGURE 21: STA 360 THRU STA 887, 2-SECTION FRAME, SUPPORT BRACKET ATTACHMENT HOLES
AT THE AIR CONDITIONING EXTRUSION - FULL FRAME SECTION REPAIR
(SHEET 2 OF 5)
Original Issue: October 04, 2006
Revision 4 February 15, 2022  Export Controlled ECCN: 9E991  737-25A1544
Copyright © Unpublished Work - See page 1 for details.  182 of 202

### Page 59

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for one body frame.
More DataQtyIdentificationNameTaskStep
-1412A3210-( )SUPPORT BRACKETRemove / Keep1
(a)2-RIVETRemove
(b)--FASTENERRemove2
(c)(d)--FRAMECut3
(e)(d)--FRAMEInspect4
(f)--FRAMEInspect5
(f)-147A3500-( )STRINGER CLIPInspect
(f)-412A3210-( )SUPPORT BRACKETInspect
(g)--ADJACENT STRUC-
TURE
Inspect6
(h)(i)1ANGLE DREPAIR ANGLE DMake7
(h)(i)1ANGLE EREPAIR ANGLE EMake
(j)1ANGLE DREPAIR ANGLE DHeat Treat8
(j)1ANGLE EREPAIR ANGLE EHeat Treat
-1ANGLE DREPAIR ANGLE DPut / Hold9
-1ANGLE EREPAIR ANGLE EPut / Hold
-1412A3210-( )SUPPORT BRACKETPut / Hold
(k)(l)--HOLEDrill
-1ANGLE DREPAIR ANGLE DRemove / Keep10
-1ANGLE EREPAIR ANGLE ERemove / Keep
-1412A3210-( )SUPPORT BRACKETRemove / Keep
(m)--PARTSDeburr
(n)-TYPE 2, CLASS ACHEMICAL CONVER-
SION COATING
Apply11
(o)-BMS 10-11, TYPE 1PRIMERApply12
(p)-BMS 5-95, CLASS B-
1/2, B-2
SEALANTApply13
(q)(r)(s)1ANGLE DREPAIR ANGLE DInstall (New)
(q)(r)(s)1ANGLE EREPAIR ANGLE EInstall (New)
(r)(u)1412A3210-( )SUPPORT BRACKETInstall (Kept)
FIGURE 21: STA 360 THRU STA 887, Z-SECTION FRAME, SUPPORT BRACKET ATTACHMENT HOLES
AT THE AIR CONDITIONING EXTRUSION - FULL FRAME SECTION REPAIR
(SHEET 3 OF 5)
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: October 04, 2006
737-25A1544Revision 4 February 15, 2022
183 of 202
BOEING SERVICE BULLETIN 737-25A1544
ALERTALERT

### Page 60

More DataQtyIdentificationNameTaskStep
(t)-BMS 3-29 (BMS 3-23
or BMS 3-35 optional)
CORROSION INHIBIT-
ING COMPOUND
Apply14
(a) Remove rivets common to support fitting and frame.
(b) Remove fasteners common to stringer clips and frame if they are in the repair area.
(c) Cut out the cracked section of the frame. Do not remove more material than necessary.
(d) Maintain a minimum 2D edge margin from adjacent fasteners. Maintain 0.50 inch minimum corner radius.
Maintain a 63 microinches Ra or better surface finish.
(e) Do a surface High Frequency Eddy Current (HFEC) inspection of the cut edges in accordance with 737
NDT Manual Part 6, 51-00-00, Procedure 4 or 23, to make sure that all cracks were removed. If no crack
is found, increase the cut out by 0.04 inch as an insurance cut. If any crack is found, repeat Step 3 and
Step 4 until no crack is found and then increase the cut out by 0.04 inch as an insurance cut.
(f) Do an open hole HFEC inspection in accordance with 737 NDT Manual Part 6, 51-00-00, Procedure 16,
for any crack, at fastener holes where fasteners were removed.
(g) Do a general visual inspection for any crack in the adjacent structure between Stringer 6 and Stringer 10.
(h) Make the two repair angles from 7075-0 Clad Sheet. If the frame is manufactured from 0.051 inch or
0.056 inch gage material, make Repair Angle D and Repair Angle E from 0.063 inch thick 7075-0 clad
sheet. If the frame is manufactured from 0.064 inch gage material, make Repair Angle D and Repair Angle
E from 0.071 inch thick 7075-0 clad sheet. Form the repair angles in the annealed condition to match the
contour of the frame in accordance with 737-600 SRM 51-30-01, 737-700 SRM 51-30-01, 737-700IGW
SRM 51-30-01, 737-800 SRM 51-30-01, 737-800BCF SRM 51-30-01 or 737-900 SRM 51-30-01.
(i) Maintain a 0.50 inch minimum corner radius. Maintain a minimum 2D edge margin. Maintain 63 microinches
Ra or better surface finish on all cut surfaces. Do not end the repair angles on existing fastener holes.
Extending the repair angles one row of fasteners beyond the existing fastener holes is acceptable. Make
sure that the length of each repair angle is sufficient to have a minimum of five rows of fasteners common
to the frame inboard and outboard flanges and a minimum of five rows of fasteners common to the frame
web above and below the cut out area.
(j) From the annealed condition to the T6 condition after forming.
(k) Drill fastener holes in Repair Angle D, Repair Angle E, stringer clip, support bracket and frame. Back drill
from existing fastener holes if these fastener holes are within the area of the repair.
(l) Maintain a minimum 2D edge margin and 4D-6D fastener spacing at new fastener locations.
(m) Remove all nicks, scratches, gouges, burrs, and sharp edges from the repair parts and installed parts.
(n) Apply chemical conversion coating to all bare aluminum surfaces. Refer to SOPM 20-43-03 as an accepted
procedure.
(o) Apply two layers of BMS 10-11, Type 1 primer to all surfaces where chemical conversion coating was
applied. Refer to SOPM 20-41-02 as an accepted procedure.
(p) Apply sealant to all faying surfaces. Refer to SOPM 20-50-19 as an accepted procedure.
(q) Maximum clearance between mating parts before fastener installation 0.010 inch. Install shims as neces-
sary. Maximum shim thickness 0.030 inch. Refer to SOPM 20-50-20 as an accepted procedure.
FIGURE 21: STA 360 THRU STA 887, Z-SECTION FRAME, SUPPORT BRACKET ATTACHMENT HOLES
AT THE AIR CONDITIONING EXTRUSION - FULL FRAME SECTION REPAIR
(SHEET 4 OF 5)
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: October 04, 2006
737-25A1544Revision 4 February 15, 2022
184 of 202
BOEING SERVICE BULLETIN 737-25A1544
ALERTALERT

The text continues at https://openairdocs.org/service-documents/boeing/737-25a1544/file/574c739c6940.md?from=61

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
