# Boeing Alert Requirements Bulletin 737-25A1873 RB: No revision named

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2024-1693; AD 2024-18-08 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Alert Requirements Bulletin 737-25A1873 RB](https://openairdocs.org/service-documents/boeing/737-25a1873-rb.md)
- Title as filed: RB-737-25A1873-00--
- Pages: 23
- PDF: https://openairdocs.org/files/sha256/f5/d5/f5d5e92d88a398c1661e234efff8e9d8662f8c208508dd38aad272afc490ffbb
- Page: https://openairdocs.org/service-documents/boeing/737-25a1873-rb/file/f5d5e92d88a3

## Text

Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Commercial 
Airplanes
737
Requirements Bulletin
ALERT
Number: 737-25A1873 RB
Original Issue: August 25, 2023
ATA System: 2520 2524 2531
SUBJECT: EQUIPMENT / FURNISHINGS - Galleys - Galley Wire Bundle Protective Wrap
Inspection and Replacement
EXPORT CONTROLLED - This technology or software is subject to the U.S. Export Administration Regulations
(EAR), (15 C.F.R. Parts 730-774). No authorization from the U.S. Department of Commerce is required for
export, re-export, in-country transfer, or access EXCEPT to country group E:1 or E:2 countries/persons per
Supp.1 to Part 740 of the EAR.
9E991ECCN:
Copyright © 2023 The Boeing Company
Treatment of this document and its content is governed by contract with Boeing. Rights to use this document
are licensed on a per aircraft basis and such rights may not be transferable. For more information, contact The
Boeing Company.
Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner,
BBJ, DC-8, DC-9, DC-10, KC-10, KC-46, KDC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8, Poseidon and
Boeing liveries are all trademarks owned by The Boeing Company; and no trademark license is granted in
connection with this document unless provided in writing by Boeing.
Original Issue: August 25, 2023
737-25A1873 RB
1 of 23
5.0

### Page 2

Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: August 25, 2023
737-25A1873 RB
2 of 23
REQUIREMENTS BULLETIN 737-25A1873
ALERTALERT
BLANK PAGE

### Page 3

Table of Contents
1. EFFECTIVITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
A. Airplanes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
B. Spares Affected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2. CONCURRENT REQUIREMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3. COMPLIANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4. APPROVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
5. ACCOMPLISHMENT INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
A. General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
B. Work Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
APPENDIX A: AFFECTED GALLEY AND CLOSET PART NUMBERS . . . . . . . . . . . . . . . . . . . 21
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: August 25, 2023
737-25A1873 RB
3 of 23
REQUIREMENTS BULLETIN 737-25A1873
ALERTALERT

### Page 4

Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: August 25, 2023
737-25A1873 RB
4 of 23
REQUIREMENTS BULLETIN 737-25A1873
ALERTALERT
BLANK PAGE

### Page 5

Commercial 
Airplanes
737
Requirements Bulletin
ALERT
Number: 737-25A1873 RB
Original Issue: August 25, 2023
ATA System: 2520 2524 2531
SUBJECT: EQUIPMENT / FURNISHINGS - Galleys - Galley Wire Bundle Protective Wrap
Inspection and Replacement
THIS DOCUMENT IS SENT TO THE OPERATORS OF RECORD OF THE AIRPLANES SHOWN IN
PARAGRAPH 1.A., EFFECTIVITY. IF AN AIRPLANE HAS BEEN LEASED OR SOLD, SEND THIS DOCUMENT
TO THE NEW OPERATOR. IF APPLICABLE SPARES HAVE BEEN SOLD, SEND THIS DOCUMENT TO THE
NEW OWNER. THIS IS AN ENHANCED REQUIRED FOR COMPLIANCE DOCUMENT. THE BOEING
PROCESSES USED TO CREATE THE SERVICE BULLETIN (SB) AND THE REQUIREMENTS BULLETIN
(RB) ENSURE THAT THE INFORMATION BETWEEN "RC START" AND "RC END" IN THE SB ARE IDENTICAL
TO THE INFORMATION IN THE SAME SECTIONS (COMPLIANCE, WORK INSTRUCTIONS…) OF THE RB
WHICH THE SB REFERS TO AS THE RELATED DOCUMENT.
1. Effectivity
A. Airplanes
This bulletin is applicable to 737-300, 737-400 Airplane(s), line number(s) 1555, 1666, 1705, 1851,
1886, 1957, 1994, 2032, 2047, 2068, 2123, 2187, 2192, 2194-2195, 2221, 2239, 2266, 2278,
2299, 2461, 2482, 2513, 2519, 2523, 2528, 2562-2564, 2598, 2602, 2604, 2620, 2665, 2689,
2717, 2732, 2833, 2845, 2891, 2902-2904, 2990, 3000, 3006, 3027, 3036, 3038-3039, 3042, 3050,
3062, 3067, 3072, 3084, 3089, 3098-3099, 3102, 3106, 3110, 3113-3114, 3119, 3121, 3125, 3127
in 5 Group(s). Where the effectivity is presented with hyphens between line numbers, the airplane
applicability means "through" and "inclusive", e.g. line numbers 1-9 means line numbers 1 through
9 inclusive.
The Variable Numbers and Group Information for the applicable airplanes is given below.
DESCRIPTIONCONFIGURATIONGROUP
737-300 airplane delivered with Galleys G1, G2, G3 and G6-1
737-300 and 737-400 airplanes delivered with Galleys G1, G2 and
G4B
-2
737-300 airplanes delivered with Galleys G1 and G4B-3
737-400 airplanes delivered with Galleys G1, G2, G4B, and Closet
or Galley G7
-4
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: August 25, 2023
737-25A1873 RB
5 of 23

### Page 6

DESCRIPTIONCONFIGURATIONGROUP
737-400 airplane delivered with Galleys G1, G4B, and Closet or
Galley G7
-5
Airplane Models:
737-300, 737-400
GroupVariable Number
2PJ601 - PJ615
1PP392
2PQ281
2PQ286
2PQ288 - PQ289
2PQ341 - PQ344
2PQ421
2PQ471
2PQ479 - PQ480
GroupVariable Number
2PQ491
3PQ996
3PR161 - PR164
3PR166 - PR172
2PV301 - PV302
2PV356 - PV357
2PW231 - PW233
2PW261
2PW265
GroupVariable Number
4PW267 - PW268
4PW278
4PW282 - PW288
5PW289
4PW290 - PW292
2PW296
2PW561
2PW563 - PW564
--
B. Spares Affected
None.
2. CONCURRENT REQUIREMENTS
None.
3. COMPLIANCE
The Federal Aviation Administration (FAA) will possibly release an additional Airworthiness Directive related
to Requirements Bulletin 737-25A1873 RB. The Airworthiness Directive will make the compliance tasks
and times given in Requirements Bulletin 737-25A1873 RB mandatory.
When more than one OPTION is given for a CONDITION, do only one of the OPTION numbers. When
more than one ACTION is given for a CONDITION or an OPTION, do all of the ACTION numbers for that
CONDITION or OPTION.
Accomplish the required action(s), based on the applicable condition(s) in Tables 1 through 5, in accordance
with Accomplishment Instructions.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: August 25, 2023
737-25A1873 RB
6 of 23
REQUIREMENTS BULLETIN 737-25A1873
ALERTALERT

### Page 7

Group 1:
Table 1: Galley Wire Bundle Protective Wrap Replacement
Repeat Interval
(Not to Exceed)
Boeing Recommended
Compliance Time
ActionCondition
-Within 21 months after
the Original Issue date of
Requirements Bulletin
737-25A1873 RB.
OPTION 1: Do an Inspec-
tion of Galley G1, G2, G3
and G6 to find the part
number.
All Airplanes.
OPTION 2: Do a mainte-
nance records check of
Galley G1, G2, G3 and
G6 to find the part num-
ber.
-Within 21 months after
the Original Issue date of
Requirements Bulletin
737-25A1873 RB.
Adjacent to the galley
identification placard, in-
spect for an existing gal-
ley modification placard.
Do an Inspection of the
modification placard.
CONDITION 1: ANY GAL-
LEY FOUND WITH AN
AFFECTED PART NUM-
BER.
-Before further flight.Replace galley wire bun-
dle spiral wrap protective
sleeving with the BMS
13-81 wire protective
sleeving.
CONDITION 1.1: ANY
GALLEY FOUND WITH-
OUT MODIFICATION
PLACARD INSTALLED OR
ANY GALLEY FOUND
WITH MODIFICATION
PLACARD INSTALLED
NOT MARKED AS MODI-
FIED PER SB 25-442.
--No further action re-
quired.
CONDITION 1.2: ANY
GALLEY FOUND WITH
MODIFICATION PLAC-
ARD INSTALLED
MARKED AS MODIFIED
PER SB 25-442.
--No further action is re-
quired.
CONDITION 2: ANY GAL-
LEY FOUND WITHOUT
AN AFFECTED PART
NUMBER.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: August 25, 2023
737-25A1873 RB
7 of 23
REQUIREMENTS BULLETIN 737-25A1873
ALERTALERT

### Page 8

Group 2:
Table 2: Galley Wire Bundle Protective Wrap Replacement
Repeat Interval
(Not to Exceed)
Boeing Recommended
Compliance Time
ActionCondition
-Within 21 months after
the Original Issue date of
Requirements Bulletin
737-25A1873 RB.
OPTION 1: Do an Inspec-
tion of Galley G1, G2 and
G4B to find the part num-
ber.
All Airplanes.
OPTION 2: Do a mainte-
nance records check of
Galley G1, G2 and G4B
to find the part number.
-Within 21 months after
the Original Issue date of
Requirements Bulletin
737-25A1873 RB.
Adjacent to the galley
identification placard, in-
spect for an existing gal-
ley modification placard.
Do an Inspection of the
modification placard.
CONDITION 3: ANY GAL-
LEY FOUND WITH AN
AFFECTED PART NUM-
BER.
-Before further flight.Replace galley wire bun-
dle spiral wrap protective
sleeving with the BMS
13-81 wire protective
sleeving.
CONDITION 3.1: ANY
GALLEY FOUND WITH-
OUT MODIFICATION
PLACARD INSTALLED OR
ANY GALLEY FOUND
WITH MODIFICATION
PLACARD INSTALLED
NOT MARKED AS MODI-
FIED PER SB 25-442.
--No further action re-
quired.
CONDITION 3.2: ANY
GALLEY FOUND WITH
MODIFICATION PLAC-
ARD INSTALLED
MARKED AS MODIFIED
PER SB 25-442.
--No further action is re-
quired.
CONDITION 4: ANY GAL-
LEY FOUND WITHOUT
AN AFFECTED PART
NUMBER.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: August 25, 2023
737-25A1873 RB
8 of 23
REQUIREMENTS BULLETIN 737-25A1873
ALERTALERT

### Page 9

Group 3:
Table 3: Galley Wire Bundle Protective Wrap Replacement
Repeat Interval
(Not to Exceed)
Boeing Recommended
Compliance Time
ActionCondition
-Within 21 months after
the Original Issue date of
Requirements Bulletin
737-25A1873 RB.
OPTION 1: Do an Inspec-
tion of Galley G1 and
G4B to find the part num-
ber.
All Airplanes.
OPTION 2: Do a mainte-
nance records check of
Galley G1 and G4B to
find the part number.
-Within 21 months after
the Original Issue date of
Requirements Bulletin
737-25A1873 RB.
Adjacent to the galley
identification placard, in-
spect for an existing gal-
ley modification placard.
Do an Inspection of the
modification placard.
CONDITION 5: ANY GAL-
LEY FOUND WITH AN
AFFECTED PART NUM-
BER.
-Before further flight.Replace galley wire bun-
dle spiral wrap protective
sleeving with the BMS
13-81 wire protective
sleeving.
CONDITION 5.1: ANY
GALLEY FOUND WITH-
OUT MODIFICATION
PLACARD INSTALLED OR
ANY GALLEY FOUND
WITH MODIFICATION
PLACARD INSTALLED
NOT MARKED AS MODI-
FIED PER SB 25-442.
--No further action re-
quired.
CONDITION 5.2: ANY
GALLEY FOUND WITH
MODIFICATION PLAC-
ARD INSTALLED
MARKED AS MODIFIED
PER SB 25-442.
--No further action is re-
quired.
CONDITION 6: ANY GAL-
LEY FOUND WITHOUT
AN AFFECTED PART
NUMBER.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: August 25, 2023
737-25A1873 RB
9 of 23
REQUIREMENTS BULLETIN 737-25A1873
ALERTALERT

### Page 10

Group 4:
Table 4: Galley and/or Closet Wire Bundle Protective Wrap Replacement
Repeat Interval
(Not to Exceed)
Boeing Recommended
Compliance Time
ActionCondition
-Within 21 months after
the Original Issue date of
Requirements Bulletin
737-25A1873 RB.
OPTION 1: Do an Inspec-
tion of Galley G1, G2,
G4B and Closet or Galley
G7 to find the part num-
ber.
All Airplanes.
OPTION 2: Do a mainte-
nance records check of
Galley G1, G2, G4B and
Closet or Galley G7 to
find the part number.
-Within 21 months after
the Original Issue date of
Requirements Bulletin
737-25A1873 RB.
Adjacent to the galley
and/or closet identifica-
tion placard, inspect for
an existing galley modifi-
cation placard. Do an In-
spection of the modifica-
tion placard.
CONDITION 7: ANY GAL-
LEY OR CLOSET FOUND
WITH AN AFFECTED
PART NUMBER.
-Before further flight.Replace galley or closet
wire bundle spiral wrap
protective sleeving with
the BMS 13-81 wire pro-
tective sleeving.
CONDITION 7.1: ANY
GALLEY OR CLOSET
FOUND WITHOUT MODI-
FICATION PLACARD IN-
STALLED OR ANY GAL-
LEY OR CLOSET FOUND
WITH MODIFICATION
PLACARD INSTALLED
NOT MARKED AS MODI-
FIED PER SB 25-442.
--No further action re-
quired.
CONDITION 7.2: ANY
GALLEY OR CLOSET
FOUND WITH MODIFICA-
TION PLACARD IN-
STALLED MARKED AS
MODIFIED PER SB 25-
442.
--No further action is re-
quired.
CONDITION 8: ANY GAL-
LEY OR CLOSET FOUND
WITHOUT AN AFFECTED
PART NUMBER.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: August 25, 2023
737-25A1873 RB
10 of 23
REQUIREMENTS BULLETIN 737-25A1873
ALERTALERT

### Page 11

Group 5:
Table 5: Galley and/or Closet Wire Bundle Protective Wrap Replacement
Repeat Interval
(Not to Exceed)
Boeing Recommended
Compliance Time
ActionCondition
-Within 21 months after
the Original Issue date of
Requirements Bulletin
737-25A1873 RB.
OPTION 1: Do an Inspec-
tion of Galley G1, G4B
and Closet or Galley G7
to find the part number.
All Airplanes.
OPTION 2: Do a mainte-
nance records check of
Galley G1, G4B and
Closet or Galley G7 to
find the part number.
-Within 21 months after
the Original Issue date of
Requirements Bulletin
737-25A1873 RB.
Adjacent to the galley
and/or closet identifica-
tion placard, inspect for
an existing galley modifi-
cation placard. Do an In-
spection of the modifica-
tion placard.
CONDITION 9: ANY GAL-
LEY OR CLOSET FOUND
WITH AN AFFECTED
PART NUMBER.
-Before further flight.Replace galley or closet
wire bundle spiral wrap
protective sleeving with
the BMS 13-81 wire pro-
tective sleeving.
CONDITION 9.1: ANY
GALLEY OR CLOSET
FOUND WITHOUT MODI-
FICATION PLACARD IN-
STALLED OR ANY GAL-
LEY OR CLOSET FOUND
WITH MODIFICATION
PLACARD INSTALLED
NOT MARKED AS MODI-
FIED PER SB 25-442.
--No further action re-
quired.
CONDITION 9.2: ANY
GALLEY OR CLOSET
FOUND WITH MODIFICA-
TION PLACARD IN-
STALLED MARKED AS
MODIFIED PER SB 25-
442.
--No further action is re-
quired.
CONDITION 10: ANY
GALLEY OR CLOSET
FOUND WITHOUT AN
AFFECTED PART NUM-
BER.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: August 25, 2023
737-25A1873 RB
11 of 23
REQUIREMENTS BULLETIN 737-25A1873
ALERTALERT

### Page 12

4. APPROVAL
This Requirements Bulletin was examined by the Federal Aviation Administration (FAA). The changes
specified in this document comply with the applicable regulations and are FAA approved, as well as European
Union Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved
airplanes listed in this Requirements Bulletin effectivity. This document and its approval were based on the
airplane in its original Boeing delivery configuration or as modified by other Boeing changes.
If an airplane has a non-Boeing modification or repair that affects a component or system also affected by
this Requirements Bulletin, the operator is responsible for obtaining appropriate regulatory agency approval
before incorporating this Requirements Bulletin.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: August 25, 2023
737-25A1873 RB
12 of 23
REQUIREMENTS BULLETIN 737-25A1873
ALERTALERT

### Page 13

5.    ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL INFORMATION
NOTE: 1. This is an Enhanced Required for Compliance document. There will be a separate
Service Bulletin (SB) and a separate Requirements Bulletin (RB). If an RB is mandated
by an Airworthiness Directive (AD), then all applicable requirements specified in the
RB must be done. For the related SB, some locations are marked RC Start and RC
End to identify the requirements that are restated from the RB. For the related SB,
the areas between RC Start and RC End, including sub-steps and any figures
identified between RC Start and RC End, must be done to comply with the AD.
Therefore, an Alternative Method of Compliance (AMOC) is required for any deviations
to steps between RC Start and RC End, including substeps and identified figures.
For the related SB, the steps not between RC Start and RC End may be deviated
from using accepted methods in accordance with the operator's maintenance or
inspection program without obtaining approval of an AMOC; this is provided that the
steps between RC Start and RC End, including sub-steps and identified figures, can
still be done as specified, and the airplane can be put back in an airworthy condition.
Figures not required for compliance are omitted from the RB.
2. This is an Enhanced Required for Compliance document. The Boeing processes
used to create the Service Bulletin (SB) and the Requirements Bulletin (RB) ensure
that the information between "RC Start" and "RC End" in the SB are identical to the
information in the same sections (Compliance, Work Instructions...) of the RB which
the SB refers to as the related document.
3. The compliance times for the actions in WORK INSTRUCTIONS are in Compliance.
4. Unless shown differently, these dimensions and tolerances are used:
– Linear dimensions are in inches
– Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus
or minus 0.03 inch
– Tolerance on rivet and bolt edge margin is plus or minus 0.05 inch
– Angular tolerance is plus or minus 2 degrees
– Hole dimensions for standard solid rivets and fasteners are in Structural Repair
Manual (SRM) Chapter 51
– Torque Values:
— Values for airframe maintenance tasks are included in Chapter 20 of
737-300/400/500 Aircraft Maintenance Manual (AMM).
— Values for electrical maintenance tasks are included in Chapter 20 of
Standard Wiring Practices Manual (SWPM).
5. These work instructions refer to procedures included in other Boeing documents.
When the words "refer to" are used and the operator has an accepted alternative
procedure, the accepted alternative procedure can be used. When the words "in
accordance with" are included in the instruction, the procedure in the Boeing document
must be used.
6. Where the work instructions include installation of a kept part, a new or serviceable
part with the same part number can be installed as an alternative to the kept part.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: August 25, 2023
737-25A1873 RB
13 of 23
REQUIREMENTS BULLETIN 737-25A1873
ALERTALERT

### Page 14

7. If it is necessary to remove more parts for access, you can remove those parts. If
you can get access without removing identified parts, it is not necessary to remove
all of the identified parts. Jacking and shoring limitations must be observed.
8. When more than one OPTION is given for a CONDITION, do only one of the OPTION
numbers. When more than one ACTION is given for a CONDITION or an OPTION,
do all of the ACTION numbers for that CONDITION or OPTION.
B. WORK INSTRUCTIONS
Actions Required for Compliance
1. Requirements:
Group 1:
TABLE 1: GALLEY WIRE BUNDLE PROTECTIVE WRAP REPLACEMENT
Refer to the listed proce-
dures in SB 737-25A1873
Original Issue or later
approved revisions as an
accepted procedure
Method of ComplianceActionCondition
Get access to the passen-
ger compartment.
-OPTION 1: Do an Inspec-
tion of Galley G1, G2, G3
and G6 to find the part
number.
All Airplanes.
APPENDIX B-
-APPENDIX A
-APPENDIX AOPTION 2: Do a mainte-
nance records check of
Galley G1, G2, G3 and G6
to find the part number.
APPENDIX C-Adjacent to the galley
identification placard, in-
spect for an existing galley
modification placard. Do
an Inspection of the modifi-
cation placard.
CONDITION 1: ANY GAL-
LEY FOUND WITH AN
AFFECTED PART NUM-
BER.
PART 1 - GALLEY WIRE
BUNDLE PROTECTIVE
WRAP REPLACEMENT
-Replace galley wire bundle
spiral wrap protective
sleeving with the BMS 13-
81 wire protective sleeving.
CONDITION 1.1: ANY
GALLEY FOUND WITH-
OUT MODIFICATION
PLACARD INSTALLED
OR ANY GALLEY FOUND
WITH MODIFICATION
PLACARD INSTALLED
NOT MARKED AS MODI-
FIED PER SB 25-442.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: August 25, 2023
737-25A1873 RB
14 of 23
REQUIREMENTS BULLETIN 737-25A1873
ALERTALERT

### Page 15

Group 1:
TABLE 1: GALLEY WIRE BUNDLE PROTECTIVE WRAP REPLACEMENT
Refer to the listed proce-
dures in SB 737-25A1873
Original Issue or later
approved revisions as an
accepted procedure
Method of ComplianceActionCondition
--No further action required.CONDITION 1.2: ANY
GALLEY FOUND WITH
MODIFICATION PLAC-
ARD INSTALLED
MARKED AS MODIFIED
PER SB 25-442.
--No further action is re-
quired.
CONDITION 2: ANY GAL-
LEY FOUND WITHOUT
AN AFFECTED PART
NUMBER.
PART 2 - CLOSE AC-
CESS
-
Group 2:
TABLE 2: GALLEY WIRE BUNDLE PROTECTIVE WRAP REPLACEMENT
Refer to the listed proce-
dures in SB 737-25A1873
Original Issue or later
approved revisions as an
accepted procedure
Method of ComplianceActionCondition
Get access to the passen-
ger compartment.
-OPTION 1: Do an Inspec-
tion of Galley G1, G2 and
G4B to find the part num-
ber.
All Airplanes.
APPENDIX B-
-APPENDIX A
-APPENDIX AOPTION 2: Do a mainte-
nance records check of
Galley G1, G2 and G4B to
find the part number.
APPENDIX C-Adjacent to the galley
identification placard, in-
spect for an existing galley
modification placard. Do
an Inspection of the modifi-
cation placard.
CONDITION 3: ANY GAL-
LEY FOUND WITH AN
AFFECTED PART NUM-
BER.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: August 25, 2023
737-25A1873 RB
15 of 23
REQUIREMENTS BULLETIN 737-25A1873
ALERTALERT

### Page 16

Group 2:
TABLE 2: GALLEY WIRE BUNDLE PROTECTIVE WRAP REPLACEMENT
Refer to the listed proce-
dures in SB 737-25A1873
Original Issue or later
approved revisions as an
accepted procedure
Method of ComplianceActionCondition
PART 1 - GALLEY WIRE
BUNDLE PROTECTIVE
WRAP REPLACEMENT
-Replace galley wire bundle
spiral wrap protective
sleeving with the BMS 13-
81 wire protective sleeving.
CONDITION 3.1: ANY
GALLEY FOUND WITH-
OUT MODIFICATION
PLACARD INSTALLED
OR ANY GALLEY FOUND
WITH MODIFICATION
PLACARD INSTALLED
NOT MARKED AS MODI-
FIED PER SB 25-442.
--No further action required.CONDITION 3.2: ANY
GALLEY FOUND WITH
MODIFICATION PLAC-
ARD INSTALLED
MARKED AS MODIFIED
PER SB 25-442.
--No further action is re-
quired.
CONDITION 4: ANY GAL-
LEY FOUND WITHOUT
AN AFFECTED PART
NUMBER.
PART 2 - CLOSE AC-
CESS
-
Group 3:
TABLE 3: GALLEY WIRE BUNDLE PROTECTIVE WRAP REPLACEMENT
Refer to the listed proce-
dures in SB 737-25A1873
Original Issue or later
approved revisions as an
accepted procedure
Method of ComplianceActionCondition
Get access to the passen-
ger compartment.
-OPTION 1: Do an Inspec-
tion of Galley G1 and G4B
to find the part number.
All Airplanes.
APPENDIX B-
-APPENDIX A
-APPENDIX AOPTION 2: Do a mainte-
nance records check of
Galley G1 and G4B to find
the part number.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: August 25, 2023
737-25A1873 RB
16 of 23
REQUIREMENTS BULLETIN 737-25A1873
ALERTALERT

### Page 17

Group 3:
TABLE 3: GALLEY WIRE BUNDLE PROTECTIVE WRAP REPLACEMENT
Refer to the listed proce-
dures in SB 737-25A1873
Original Issue or later
approved revisions as an
accepted procedure
Method of ComplianceActionCondition
APPENDIX C-Adjacent to the galley
identification placard, in-
spect for an existing galley
modification placard. Do
an Inspection of the modifi-
cation placard.
CONDITION 5: ANY GAL-
LEY FOUND WITH AN
AFFECTED PART NUM-
BER.
PART 1 - GALLEY WIRE
BUNDLE PROTECTIVE
WRAP REPLACEMENT
-Replace galley wire bundle
spiral wrap protective
sleeving with the BMS 13-
81 wire protective sleeving.
CONDITION 5.1: ANY
GALLEY FOUND WITH-
OUT MODIFICATION
PLACARD INSTALLED
OR ANY GALLEY FOUND
WITH MODIFICATION
PLACARD INSTALLED
NOT MARKED AS MODI-
FIED PER SB 25-442.
--No further action required.CONDITION 5.2: ANY
GALLEY FOUND WITH
MODIFICATION PLAC-
ARD INSTALLED
MARKED AS MODIFIED
PER SB 25-442.
--No further action is re-
quired.
CONDITION 6: ANY GAL-
LEY FOUND WITHOUT
AN AFFECTED PART
NUMBER.
PART 2 - CLOSE AC-
CESS
-
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: August 25, 2023
737-25A1873 RB
17 of 23
REQUIREMENTS BULLETIN 737-25A1873
ALERTALERT

### Page 18

Group 4:
TABLE 4: GALLEY AND/OR CLOSET WIRE BUNDLE PROTECTIVE WRAP REPLACEMENT
Refer to the listed proce-
dures in SB 737-25A1873
Original Issue or later
approved revisions as an
accepted procedure
Method of ComplianceActionCondition
Get access to the passen-
ger compartment.
-OPTION 1: Do an Inspec-
tion of Galley G1, G2, G4B
and Closet or Galley G7 to
find the part number.
All Airplanes.
APPENDIX B-
-APPENDIX A
-APPENDIX AOPTION 2: Do a mainte-
nance records check of
Galley G1, G2, G4B and
Closet or Galley G7 to find
the part number.
APPENDIX C-Adjacent to the galley or
closet identification plac-
ard, inspect for an existing
galley or closet modifica-
tion placard. Do an Inspec-
tion of the modification
placard.
CONDITION 7: ANY GAL-
LEY OR CLOSET FOUND
WITH AN AFFECTED
PART NUMBER.
PART 1 - GALLEY OR
CLOSET WIRE BUNDLE
PROTECTIVE WRAP RE-
PLACEMENT
-Replace galley or closet
wire bundle spiral wrap
protective sleeving with the
BMS 13-81 wire protective
sleeving.
CONDITION 7.1: ANY
GALLEY OR CLOSET
FOUND WITHOUT MODI-
FICATION PLACARD IN-
STALLED OR ANY GAL-
LEY OR CLOSET FOUND
WITH MODIFICATION
PLACARD INSTALLED
NOT MARKED AS MODI-
FIED PER SB 25-442.
--No further action required.CONDITION 7.2: ANY
GALLEY OR CLOSET
FOUND WITH MODIFICA-
TION PLACARD IN-
STALLED MARKED AS
MODIFIED PER SB 25-
442.
--No further action is re-
quired.
CONDITION 8: ANY GAL-
LEY OR CLOSET FOUND
WITHOUT AN AFFECTED
PART NUMBER.
PART 2 - CLOSE AC-
CESS
-
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: August 25, 2023
737-25A1873 RB
18 of 23
REQUIREMENTS BULLETIN 737-25A1873
ALERTALERT

### Page 19

Group 5:
TABLE 5: GALLEY AND/OR CLOSET WIRE BUNDLE PROTECTIVE WRAP REPLACEMENT
Refer to the listed proce-
dures in SB 737-25A1873
Original Issue or later
approved revisions as an
accepted procedure
Method of ComplianceActionCondition
Get access to the passen-
ger compartment.
-OPTION 1: Do an Inspec-
tion of Galley G1, G4B and
Closet or Galley G7 to find
the part number.
All Airplanes.
APPENDIX B-
-APPENDIX A
-APPENDIX AOPTION 2: Do a mainte-
nance records check of
Galley G1, G4B and Closet
or Galley G7 to find the
part number.
APPENDIX C-Adjacent to the galley or
closet identification plac-
ard, inspect for an existing
galley or closet modifica-
tion placard. Do an Inspec-
tion of the modification
placard.
CONDITION 9: ANY GAL-
LEY OR CLOSET FOUND
WITH AN AFFECTED
PART NUMBER.
PART 1 - GALLEY OR
CLOSET WIRE BUNDLE
PROTECTIVE WRAP RE-
PLACEMENT
-Replace galley or closet
wire bundle spiral wrap
protective sleeving with the
BMS 13-81 wire protective
sleeving.
CONDITION 9.1: ANY
GALLEY OR CLOSET
FOUND WITHOUT MODI-
FICATION PLACARD IN-
STALLED OR ANY GAL-
LEY OR CLOSET FOUND
WITH MODIFICATION
PLACARD INSTALLED
NOT MARKED AS MODI-
FIED PER SB 25-442.
--No further action required.CONDITION 9.2: ANY
GALLEY OR CLOSET
FOUND WITH MODIFICA-
TION PLACARD IN-
STALLED MARKED AS
MODIFIED PER SB 25-
442.
--No further action is re-
quired.
CONDITION 10: ANY
GALLEY OR CLOSET
FOUND WITHOUT AN
AFFECTED PART NUM-
BER.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: August 25, 2023
737-25A1873 RB
19 of 23
REQUIREMENTS BULLETIN 737-25A1873
ALERTALERT

### Page 20

Group 5:
TABLE 5: GALLEY AND/OR CLOSET WIRE BUNDLE PROTECTIVE WRAP REPLACEMENT
Refer to the listed proce-
dures in SB 737-25A1873
Original Issue or later
approved revisions as an
accepted procedure
Method of ComplianceActionCondition
PART 2 - CLOSE AC-
CESS
-
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: August 25, 2023
737-25A1873 RB
20 of 23
REQUIREMENTS BULLETIN 737-25A1873
ALERTALERT

### Page 21

Affected Part NumberGroupDescription
101001-1Groups 1-5GALLEY G1
101014-1
101014-101
101018-1
101018-1001
101018-101
101018-201
101018-401
101018-501
101018-601
101018-801
101096-1
101099-1
101199-1
101462-1M001
101716-301
APPENDIX A:  AFFECTED GALLEY AND CLOSET PART NUMBERS
(SHEET 1 OF 3)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: August 25, 2023
737-25A1873 RB
21 of 23
REQUIREMENTS BULLETIN 737-25A1873
ALERTALERT

### Page 22

Affected Part NumberGroupDescription
101002-1Groups 1-2,4GALLEY G2
101015-1
101015-101
101019-1
101019-101
101019-201
101019-301
101019-401
101069-1
101069-101
101069-301
101069-301M001
101069-301M002
101097-1
101100-1
101187-1
101200-1
101003-1Group 1GALLEY G3
APPENDIX A:  AFFECTED GALLEY AND CLOSET PART NUMBERS
(SHEET 2 OF 3)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: August 25, 2023
737-25A1873 RB
22 of 23
REQUIREMENTS BULLETIN 737-25A1873
ALERTALERT

### Page 23

Affected Part NumberGroupDescription
101016-1Groups 2-5GALLEY G4B
101016-101
101016-201
101020-1
101095-1
101095-101
101095-301
101095-401
101095-501
101095-701
101098-1
101101-1
101188-101
101201-1
101201-101
101464-1M001
101721-101
101721-501
101003-2Group 1GALLEY G6
101237-1Group 4-5CLOSET OR GALLEY
G7
APPENDIX A:  AFFECTED GALLEY AND CLOSET PART NUMBERS
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: August 25, 2023
737-25A1873 RB
23 of 23
REQUIREMENTS BULLETIN 737-25A1873
ALERTALERT

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
