# Boeing Alert Service Bulletin 737-27A1278: Revision 1

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2008-0415; AD 2011-27-03 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Alert Service Bulletin 737-27A1278](https://openairdocs.org/service-documents/boeing/737-27a1278.md)
- Title as filed: U.S. DOT/FAA - Service Bulletin
- Pages: 83
- PDF: https://openairdocs.org/files/sha256/b8/15/b8153b5e3b7cb746cc919574cc521eb2f2bf9db6f5efcf73cc6aadcc238ac984
- Page: https://openairdocs.org/service-documents/boeing/737-27a1278/file/b8153b5e3b7c

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Commercial 
Airplanes
737
Service Bulletin
ALERT
Number: 737-27A1278
Original Issue: May 24, 2007
Revision 1: January 07, 2010
ATA System: 2741
SUBJECT: FLIGHT CONTROLS - Horizontal Stabilizer Trim Control System - Ballscrew and Ball
Nut Inspection and Lubrication
Export of this technology is controlled under the United States Export Administration Regulations (EAR) (15
CFR 730-774). An export license may be required before it is used for development, production or use by foreign
persons from specific countries. The controller of this data has the individual responsibility to abide by all export
laws.
9E991ECCN:
BOEING PROPRIETARY, CONFIDENTIAL, AND/OR TRADE SECRET
Copyright © 2007 The Boeing Company
Unpublished Work - All Rights Reserved
Boeing claims copyright in each page of this document only to the extent that the page contains copyrightable
subject matter. Boeing also claims copyright in this document as a compilation and/or collective work.
This document includes proprietary information owned by The Boeing Company and/or one or more third parties.
Treatment of the document and the information it contains is governed by contract with Boeing. For more
information, contact The Boeing Company, P.O. Box 3707, Seattle, Washington 98124.
Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner,
BBJ, DC-8, DC-9, DC-10, KC-10, KDC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8A, Poseidon and the
Boeing livery are all trademarks owned by The Boeing Company; and no trademark license is granted in
connection with this document unless provided in writing by Boeing.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: May 24, 2007
737-27A1278Revision 1: January 07, 2010
1 of 83
5.0

### Page 2

BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: May 24, 2007
737-27A1278Revision 1: January 07, 2010
2 of 83
BOEING SERVICE BULLETIN 737-27A1278
ALERTALERT
BLANK PAGE

### Page 3

Table of Contents
Revision Transmittal Sheet ............................................ 5
Summary ...................................................... 9
1. PLANNING INFORMATION ........................................ 1 5
A. Effectivity ............................................... 1 5
1. Airplanes ............................................ 1 5
2. Spares Affected ........................................ 2 8
B. Concurrent Requirements ...................................... 2 9
C. Reason ................................................ 2 9
D. Description .............................................. 3 1
E. Compliance .............................................. 3 4
F. Approval ............................................... 3 8
G. Manpower .............................................. 3 8
H. Weight and Balance Changes .................................... 3 9
I. Electrical Load Data ......................................... 3 9
J. References .............................................. 3 9
1. Existing Data: ......................................... 3 9
2. Data supplied with this Service Bulletin: ........................... 4 0
3. Installation Drawings Used in the Preparation of this Service Bulletin: ........... 4 0
K. Publications Affected ........................................ 4 1
L. Interchangeability and Intermixability of Parts ........................... 4 1
2. MATERIAL INFORMATION ........................................ 4 3
A. Material - Price and Availability ................................... 4 3
B. Industry Support Information .................................... 4 3
C. Parts Necessary For Each Airplane ................................. 4 3
1. Kits/Parts: ........................................... 4 3
2. Parts and Materials Supplied by the Operator: ........................ 4 3
3. Parts Modified and Reidentified: ............................... 4 4
4. Parts Removed and Not Replaced: .............................. 4 4
D. Parts Necessary to Change Spares ................................. 4 4
E. Special Tooling - Price and Availability ............................... 4 4
F. Special Tooling Necessary to do this Service Bulletin ....................... 4 4
3. ACCOMPLISHMENT INSTRUCTIONS .................................. 4 5
A. GENERAL INFORMATION ..................................... 4 5
B. WORK INSTRUCTIONS ....................................... 4 6
FIGURE 1: HORIZONTAL STABILIZER TRIM ACTUATOR - DETAILED INSPECTION OF THE
BALLSCREW, BALL NUT, AND THE ATTACHMENT FITTINGS- (GROUP 1 CONFIGURATION
1, GROUP 2 CONFIGURATION 1, AND GROUP 3 AIRPLANES) [Group 1-2, Configuration 1;
Group 3] ............................................. 5 9
FIGURE 2: HORIZONTAL STABILIZER TRIM ACTUATOR - DETAILED INSPECTION OF THE
BALLSCREW, BALL NUT, AND THE ATTACHMENT FITTINGS - (GROUP 1, CONFIGURATION
2 AIRPLANES) [Group 1, Configuration 2] .......................... 6 3
FIGURE 3: HORIZONTAL STABILIZER TRIM ACTUATOR - DETAILED INSPECTION OF THE
BALLSCREW, BALL NUT, AND, AND THE ATTACHMENT FITTINGS - (GROUP 2,
CONFIGURATION 2 AIRPLANES) [Group 2, Configuration 2] ............... 6 7
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: May 24, 2007
737-27A1278Revision 1: January 07, 2010
3 of 83
BOEING SERVICE BULLETIN 737-27A1278
ALERTALERT

### Page 4

FIGURE 4: LUBRICATION OF THE HORIZONTAL STABILIZER TRIM ACTUATOR (GROUP 1
CONFIGURATION 1, GROUP 2 CONFIGURATION 1, AND GROUP 3 AIRPLANES) [Group
1-2, Configuration 1; Group 3] ................................. 7 1
FIGURE 5: LUBRICATION OF THE HORIZONTAL STABILIZER TRIM ACTUATOR (GROUP 1,
CONFIGURATION 2 AIRPLANES) [Group 1, Configuration 2] ............... 7 3
FIGURE 6: LUBRICATION OF THE HORIZONTAL STABILIZER TRIM ACTUATOR (GROUP 2,
CONFIGURATION 2 AIRPLANES) [Group 2, Configuration 2] ............... 7 5
FIGURE 7: HORIZONTAL STABILIZER TRIM ACTUATOR BALLSCREW AND BALL NUT -
REPAIR/REPLACE - (GROUP 1 CONFIGURATION 1, GROUP 2 CONFIGURATION 1, AND
GROUP 3 AIRPLANES) [Group 1-2, Configuration 1; Group 3] ............... 7 7
FIGURE 8: HORIZONTAL STABILIZER TRIM ACTUATOR BALLSCREW AND BALL NUT -
REPAIR/REPLACE - (GROUP 1, CONFIGURATION 2 AIRPLANES) [Group 1, Configuration
2 ]  ................................................ 7 9
FIGURE 9: HORIZONTAL STABILIZER TRIM ACTUATOR BALLSCREW AND BALL NUT -
REPAIR/REPLACE - (GROUP 2, CONFIGURATION 2 AIRPLANES) [Group 2, Configuration
2 ]  ................................................ 8 1
Appendix A: INSPECTION REPORT FORM FOR SB 737-27A1278 ................... 8 3
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: May 24, 2007
737-27A1278Revision 1: January 07, 2010
4 of 83
BOEING SERVICE BULLETIN 737-27A1278
ALERTALERT

### Page 5

Commercial 
Airplanes
737
Service Bulletin
ALERT
Revision Transmittal SheetNumber: 737-27A1278Original Issue: May 24, 2007
Revision 1: January 07, 2010
ATA System: 2741
SUBJECT: FLIGHT CONTROLS - Horizontal Stabilizer Trim Control System - Ballscrew and Ball
Nut Inspection and Lubrication
This revision includes all pages of the service bulletin.
COMPLIANCE INFORMATION RELATED TO THIS REVISION
No more work is necessary on airplanes changed as shown in the original issue of this service bulletin. However,
Operators have to continue to do the repeat Detailed Inspection, Lubrication, and Overhaul in accordance with
Paragraph 1.E., Compliance, Table 1 or Table 2 as applicable.
Federal Aviation Administration (FAA) Notice of Proposed Rule Making FAA NPRM 2007-NM-256-AD, is related
to this service bulletin.
NOTE: The Operators that performed the initial Detailed Inspection, Lubrification, and Overhaul do not have
to do another initial inspection, but have to continue to do the repeat Detailed Inspection, Lubrication,
and Overhaul of the Horizontal Stabilizer Trim Actuator in accordance with Paragraph 1.E., Compliance,
Table 1 or Table 2 as applicable.
The Operators that incorporated service bulletin UMBRA CUSCINETTI, S.p.A. SB 07322-27-01 or
service bulletin LINEAR MOTION, LLC SB 7901708 or service bulletin SKYTRONICS, Inc. SB 93004
as given in WORK PACKAGE 4, have to continue to do the repeat Detailed Inspection, Lubrication,
and Overhaul of the Horizontal Stabilizer Trim Actuator in accordance with Paragraph 1.E., Compliance,
Table 1 or Table 2 as applicable.
The Operators that did not incorporate UMBRA CUSCINETTI S.p.A. or LINEAR MOTION LLC or
SKYTRONIC INC service bulletin, have to incorporate service bulletin UMBRA CUSCINETTI, S.p.A.
SB 07322-27-01 or service bulletin LINEAR MOTION, LLC SB 7901708 or service bulletin SKYTRONICS,
Inc. SB 93004 as given in WORK PACKAGE 4, and have to continue to do the repeat Detailed
Inspection, Lubrication, and Overhaul of the Horizontal Stabilizer Trim Actuator in accordance with
Paragraph 1.E., Compliance, Table 1 or Table 2 as applicable.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: May 24, 2007
737-27A1278Revision 1: January 07, 2010
5 of 83

### Page 6

REASON FOR REVISION
This revision is sent to correct the work instructions for the HSTA name plate identification information in WORK
PACKAGE 4 and to clarify some of the inspections necessary in WORK PACKAGE 1 and WORK PACKAGE
2. A note is also added in the compliance table to advise operators to do the lubrication task during the detailed
inspection task. In addition, reference to the "Horizontal Stabilizer Gearbox End Play Test as given OHM 27-45-11"
is added. This is because the Horizontal Stabilizer Gearbox Backlash Inspection is only given in the AMM for
737-600/700/800/900 airplane. The (OHM) Horizontal Stabilizer Gearbox End Play Test is a similar test and is
applicable to all 737-100/200/300/400/500 airplane variants.
These sections are changed:
1. Paragraph 1.D., Description: Affected Maintenance Zones are added for each airplane group.
2. Paragraph 1.E., Compliance: Notes (a) and (b) are added to Table 1 and Table 2 to recommend operators
to do a lubrication task during the detailed inspection task.
3. Paragraph 1.E., Compliance: Notice of Propose Rule Making 2007-NM-256-AD is added.
4. Paragraph 1.K., Publications Affected: Added Damage Tolerance Based Structural Inspection statement.
5. Paragraph 3.A, General Information: General Visual Inspection note added.
6. Paragraph 3.B, Work Instructions:
a. WORK PACKAGE 1:
– Added some notes, added more data to some step instructions, deleted some unnecessary step
instructions and correctly re-sequenced the steps.
b. WORK PACKAGE 2:
– Added some notes, added more data to some step instructions, deleted some unnecessary step
instructions and correctly re-sequenced the steps.
c. WORK PACKAGE 4:
– Step 1.a. revised to reference SB 737-27A1278 WORK PACKAGE 4 instead of 737-27A1278
WORK PACKAGE 3.
– Step 2.a. revised to reference SB 737-27A1278 WORK PACKAGE 4 instead of 737-27A1278
WORK PACKAGE 3.
– Step 3.b. revised to reference SB 737-27A1278 WORK PACKAGE 4 instead of 737-27A1278
WORK PACKAGE 3.
7. FIGURE 1: Step 10, inspection for large amount of grease that exits the Ball Nut and note (a) are removed.
8. FIGURE 2: Step 10, inspection for large amount of grease that exits the Ball Nut and note (a) are removed.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: May 24, 2007
737-27A1278Revision 1: January 07, 2010
6 of 83
BOEING SERVICE BULLETIN 737-27A1278
ALERTALERT

### Page 7

9. FIGURE 7 sheet 2: Step 4, reference to Aircraft Maintenance Manual (AMM) removed and replaced with
internal reference note (b). Also the step table note (b) is revised to reference Horizontal Stabilizer Gearbox
End Play Test as given in OHM 27-45-11 instead of the Horizontal Stabilizer Gearbox Backlash inspection
as given in AMM 27-41-81/606.
10. FIGURE 8 sheet 2: Step 4, reference to Aircraft Maintenance Manual (AMM) removed and replaced with
internal reference note (b). Also the step table note (b) is revised to reference Horizontal Stabilizer Gearbox
End Play Test as given in OHM 27-45-11 instead of the Horizontal Stabilizer Gearbox Backlash inspection
as given in AMM 27-41-81/606.
11. FIGURE 9 sheet 2: Step 4, reference to Aircraft Maintenance Manual (AMM) removed and replaced with
internal reference note (b). Also the step table note (b) is revised to reference Horizontal Stabilizer Gearbox
End Play Test as given in OHM 27-45-11 instead of the Horizontal Stabilizer Gearbox Backlash inspection
as given in AMM 27-41-81/606.
The data given in Information Notice 737-27A1278 IN 01 is included in this revision.
Vertical lines are put on the left edge of each page, except in Paragraph 1.A., Effectivity, to show the location
of important changes.
Pages with no vertical lines have no important changes.
REVISION HISTORY
May 24, 2007Original Issue:
January 07, 2010Revision 1:
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: May 24, 2007
737-27A1278Revision 1: January 07, 2010
7 of 83
BOEING SERVICE BULLETIN 737-27A1278
ALERTALERT

### Page 8

BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: May 24, 2007
737-27A1278Revision 1: January 07, 2010
8 of 83
BOEING SERVICE BULLETIN 737-27A1278
ALERTALERT
BLANK PAGE

### Page 9

Commercial 
Airplanes
737
Service Bulletin
ALERT
SummaryNumber: 737-27A1278Original Issue: May 24, 2007
Revision 1: January 07, 2010
ATA System: 2741
SUBJECT: FLIGHT CONTROLS - Horizontal Stabilizer Trim Control System - Ballscrew and Ball
Nut Inspection and Lubrication
THIS BULLETIN IS SENT TO THE OPERATORS OF RECORD OF THE AIRPLANES SHOWN IN PARAGRAPH
1.A., EFFECTIVITY. IF AN AIRPLANE HAS BEEN LEASED OR SOLD, SEND THIS SERVICE BULLETIN TO
THE NEW OPERATOR. IF APPLICABLE SPARES HAVE BEEN SOLD, SEND THIS SERVICE BULLETIN TO
THE NEW OWNER.
CONCURRENT REQUIREMENTS
None.
BACKGROUND
This service bulletin is being issued to maintain the frequency of the detailed inspection of the Horizontal Stabilizer
Trim Actuator (HSTA) Ballscrew and Ball Nut as specified in the Maintenance Planning Document. This service
bulletin also gives instructions to remove/replace and repair the Horizontal Stabilizer Trim Actuator if a damaged
Ballscrew or Ball Nut is found. This service bulletin also adds the recommended intervals for repeat lubrication
and overhaul. Also, this service bulletin gives recommended compliance time for incorporation of the suppliers
service bulletins (service bulletin UMBRA CUSCINETTI, S.p.A. SB 07322-27-01, service bulletin LINEAR
MOTION, LLC SB 7901708, and service bulletin SKYTRONICS, Inc. SB 93004). The UMBRA CUSCINETTI
supplier service bulletin provides instructions to remove and replace the Ball Nut Tube Retainers on the 737
Horizontal Stabilizer Trim Actuator Ballscrew assembly with new Tube Retainers. The LINEAR MOTION supplier
service bulletin provides instructions to remove and replace the Ball Deflectors and the Ball Return Guide Clamps
on 737 Horizontal Stabilizer Trim Actuator Ballscrew assembly with new Ball Deflectors and Ball Return Guide
Clamps. The SKYTRONICS supplier service bulletin provides instructions to remove and replace the Return
Tube Clamps on the 737 Horizontal Stabilizer Trim Actuator Ballscrew assembly with new Return Tube Clamps.
The new parts installed will have sufficient stiffness to retain the load carrying balls in all known failure mode
conditions. The changes given in this bulletin will reduce the probability of loss of the primary and secondary
load paths of the Stabilizer Trim Actuator. Loss of primary and secondary load paths of the Stabilizer Trim
Actuator could result in the loss of control of the airplane.
This Service Bulletin also specifies the time for incorporation of the Boeing Service Bulletin 737-27-1046 Revision
1 (as applicable), dated April 5, 1974, if the service bulletin is not already incorporated. Boeing Service Bulletin
737-27-1046 Revision 1 applies to airplanes 737-100/200 with oil lubricators and provides instructions for
removing the existing oil lubricators and installation of a grease fitting on the Horizontal Stabilizer Trim Actuator
Ball Nut.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: May 24, 2007
737-27A1278Revision 1: January 07, 2010
9 of 83

### Page 10

NOTE: The Horizontal Stabilizer Trim Actuator Ballscrew Assembly 102J033-1 or 102J033-1 (OS) with Oil
Lubricator can not be reworked to a Horizontal Stabilizer Trim Actuator Ballscrew Assembly with grease
lubrication fitting as given in Boeing Service Bulletin 737-27-1046 Revision 1. Remove these Stabilizer
Trim Actuator Ballscrew Assemblies with Oil Lubricator and install 102J033-3 or 102J033-502 Horizontal
Stabilizer Trim Actuator Ballscrew Assembly
This service bulletin is being issued to maintain the frequency of the detailed visual inspection of the Horizontal
Stabilizer Trim Actuator Ballscrew and Ball Nut as specified in the Maintenance Planning Document. This service
bulletin also gives instructions to remove/replace and repair the Horizontal Stabilizer Trim Actuator if a damaged
Ballscrew or Ball Nut is found. This service bulletin also adds the recommended intervals for repeat lubrication
and overhaul.
After a Horizontal Stabilizer jackscrew incident related to a MD-80 airplane, Boeing initiated a design review of
the Boeing heritage horizontal stabilizer ballscrew primary and secondary load paths. During this review, one
757 operator reported a Horizontal Stabilizer Ballscrew with extensive corrosion. An investigation was initiated.
This investigation identified that a maintenance procedure to check the stabilizer Ballscrew primary load path
was required. In addition, the design review found that the Ball Nut Tube Retainers on the 737 Horizontal
Stabilizer Trim Actuator should be stiffened, so that the balls are retained within the assembly when the balls
are jammed and not free to circulate.
NOTE: Boeing also recommends that the Maintenance Planning Document (MPD) intervals be observed for
the "Lubrication" and "Detailed Inspection" actions prior to compliance with this service bulletin. The
"Lubrication" and "Detailed Inspection" done as given in this service bulletin satisfy the "Lubrication"
and "Detailed Inspection" requirements given in Maintenance Planning Document" (MPD).
Boeing Service Related Problem (SRP) 737CL-SRP-27-0153 is related to this bulletin.
ACTION (PRR 35005-261RS)
Get access to the Horizontal Stabilizer Trim Actuator and do the procedures that follow below at the intervals
shown in the compliance section.
1. DETAILED INSPECTION:
– Do the Detailed Inspection as given in Accomplishment Instructions, Paragraph 3.B., Work Instructions,
WORK PACKAGE 1 or WORK PACKAGE 2 (as applicable).
LUBRICATE THE HORIZONTAL TRIM ACTUATOR:
– Do the lubrication as given in Accomplishment Instructions, Paragraph 3.B., Work Instructions, WORK
PACKAGE 1 or WORK PACKAGE 2 (as applicable).
REMOVE and REPAIR/REPLACE THE HORIZONTAL TRIM ACTUATOR: Remove/Replace the Horizontal
Stabilizer Trim Actuator if damage is found as given in Accomplishment Instructions, Paragraph 3.B., Work
Instructions, WORK PACKAGE 1 or WORK PACKAGE 2 (as applicable).
NOTE: As an option, Operators can replace a damaged Horizontal Stabilizer Trim Actuator with a
serviceable Stabilizer Trim Actuator that is not new or not overhauled. Before the next flight, do
the Detailed Inspection and Lubrication for the replacement Stabilizer Trim Actuator as given in
this service bulletin and do the End Play Test as given in OHM 27-45-11. After the installation
follow the requirements of this service bulletin.
2. For airplanes with Horizontal Stabilizer Trim Actuator Ballscrew Assemblies with Oil Lubricators:
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: May 24, 2007
737-27A1278Revision 1: January 07, 2010
10 of 83
BOEING SERVICE BULLETIN 737-27A1278
ALERTALERT

### Page 11

a. CHECK the Horizontal Stabilizer Trim Actuator Ballscrew Assy Part Number. If you find Horizontal
Stabilizer Trim Actuator Ballscrew Assemblies 102J033-1 (Boeing Part Number 10-61302-1) or
102J033-1 (OS) (Boeing Part Number 10-61302-1), remove and install Stabilizer Ballscrew Assy
102J033-3 (Boeing Part Number 10-61302-2) or 102J033-502 (Boeing Part Number 10-61302-7) as
given in Accomplishment Instructions, Paragraph 3.B., Work Instructions, WORK PACKAGE 3.
NOTE: The Horizontal Stabilizer Trim Actuator Ballscrew Assembly 102J033-1 or 102J033-1 (OS)
with Oil Lubricator can not be reworked to a Horizontal Stabilizer Trim Actuator Ballscrew
Assembly with grease lubrication fitting as given in Service Bulletin 737-27-1046 Revision 1.
The 102J033-3 (Boeing Part Number 10-61302-2) is an oil lubricated Horizontal Stabilizer
Trim Actuator Ballscrew Assembly and operators have to incorporate Boeing Service Bulletin
737-27-1046 Revision 1 and the SKYTRONICS, Inc. SB 93004. The 102J033-502 (Boeing
Part Number 10-61302-7) is a grease lubricated Horizontal Stabilizer Trim Actuator Ballscrew
Assembly with reinforced Return Tube Clamps, and Operators do not have to incorporate
Boeing Service Bulletin 737-27-1046 Revision 1 and service bulletin SKYTRONICS, Inc. SB
93004.
b. INCORPORATE BOEING SERVICE BULLETIN 737-27-1046 Revision 1 as applicable: Incorporate
SB 737-27-1046 Revision 1 as given in Accomplishment Instructions, Paragraph 3.B., Work Instructions,
WORK PACKAGE 3.
NOTE: Service Bulletin 737-27-1046 Revision 1 is applicable for some 737-100/200 airplanes with
Ballscrew Oil Lubricators. This Service Bulletin provides instructions for the removal of the
existing Oil Lubricators and the installation of a grease fitting on the Horizontal Stabilizer Trim
Actuator Ball Nut. The Horizontal Stabilizer Trim Actuator Ballscrew Assembly 102J033-1 or
102J033-1 (OS) with Oil Lubricator can not be reworked to a Horizontal Stabilizer Trim Actuator
Ballscrew Assembly with grease lubrication fitting.
3. INCORPORATE ONE OF THE FOLLOWING SUPPLIER SERVICE BULLETINS as given in Accomplishment
Instructions, Paragraph 3.B., Work Instructions, WORK PACKAGE 4:
– UMBRA CUSCINETTI, S.p.A. SB 07322-27-01, Rev 00, Dated December 21, 2004: Install the new
Ball Nut Tube Retainers as given in this supplier service bulletin.
– LINEAR MOTION, LLC SB 7901708, Dated July 26, 2005: Install the new Ball Deflectors and Ball
Return Guide Clamps as given in this supplier service bulletin.
– SKYTRONICS, Inc. SB 93004, Dated September 01, 2005: Install the new Return Tube Clamps as
given in this supplier service bulletin.
4. REMOVE AND REPAIR/OVERHAUL THE HORIZONTAL STABILIZER TRIM ACTUATOR:
– Remove and repair/overhaul the Horizontal Stabilizer Trim Actuator as given in Accomplishment
Instructions, Paragraph 3.B., Work Instructions, WORK PACKAGE 5.
EFFECTIVITY
All 737-100/200/300/400/500 Airplanes divided in three groups. Refer to Paragraph 1.A.1., Airplanes for the list
of affected airplanes.
COMPLIANCE
Refer to Paragraph 1.E., Compliance.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: May 24, 2007
737-27A1278Revision 1: January 07, 2010
11 of 83
BOEING SERVICE BULLETIN 737-27A1278
ALERTALERT

### Page 12

INDUSTRY SUPPORT INFORMATION
Boeing warranty remedies are available for airplanes in warranty as of June 14, 2001. Please refer to Paragraph
2.B., Industry Support Information.
MANPOWER
Refer to Paragraph 1.G., Manpower.
MATERIAL INFORMATION
None. Refer to Paragraph 2.A., Material - Price and Availability.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: May 24, 2007
737-27A1278Revision 1: January 07, 2010
12 of 83
BOEING SERVICE BULLETIN 737-27A1278
ALERTALERT

### Page 13 (OCR)

BOEING SERVICE BULLETIN 737-27A1278
ALERT  ALERT
HORIZONTAL STABILIZER TRIM ACTUATOR ASSEMBLY.
DO A DETAILED INSPECTION, LUBRICATE AND REPAIR/OVERHAUL
HORIZONTAL STABILIZER TRIM ACTUATOR ASSEMBLY.
REPLACE STABILIZER TRIM ACTUATOR BALLSCREW ASSEMBLY
102J033-1 OR 102J033-1(OS) WITH 102J033-3 OR 102J033-502.
INCORPORATE BOEING SERVICE BULLETIN 737-27-1046, IF
APPLICABLE.
INCORPORATE THE APPLICABLE SUPPLIER SERVICE BULLETIN:
UMBRA CUSCINETTI S.p.A. 07322-27-01, OR LINEAR MOTION
7901708, OR SKYTRONICS, INC. 93004.
D64048
Original Issue: May 24, 2007
Revision 1: January 07, 2010  737-27A1278
Copyright © Unpublished Work - See page 1 for details.  BOEING PROPRIETARY -  13 of 83

### Page 14

BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: May 24, 2007
737-27A1278Revision 1: January 07, 2010
14 of 83
BOEING SERVICE BULLETIN 737-27A1278
ALERTALERT
BLANK PAGE

### Page 15

Commercial 
Airplanes
737
Service Bulletin
ALERT
Number: 737-27A1278
Original Issue: May 24, 2007
Revision 1: January 07, 2010
ATA System: 2741
SUBJECT: FLIGHT CONTROLS - Horizontal Stabilizer Trim Control System - Ballscrew and Ball
Nut Inspection and Lubrication
THIS BULLETIN IS SENT TO THE OPERATORS OF RECORD OF THE AIRPLANES SHOWN IN PARAGRAPH
1.A., EFFECTIVITY. IF AN AIRPLANE HAS BEEN LEASED OR SOLD, SEND THIS SERVICE BULLETIN TO
THE NEW OPERATOR. IF APPLICABLE SPARES HAVE BEEN SOLD, SEND THIS SERVICE BULLETIN TO
THE NEW OWNER.
1.    PLANNING INFORMATION
A. Effectivity
1. Airplanes
Refer to Service Bulletin Index Document D6-19567 Part 3 for Airplane Variable Number, Line
Number, and Serial Number data.
This service bulletin is for the airplanes shown below.
Refer to PRR 35005-261RS for data about this change.
DESCRIPTIONCONFIGURATIONGROUP
737-300/400/500 Airplanes-1
Airplanes with a separate Autopilot Actuator.1
Airplanes with Primary Stabilizer Trim Actuator.2
737-100/200 Airplanes delivered with Horizontal Stabilizer Trim
Actuator Oil Lubricator.
-2
737-100/200 Airplanes that incorporated Service Bulletin 737-27-1046.1
737-100/200 Airplanes that did not incorporate Service Bulletin
737-27-1046.
2
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: May 24, 2007
737-27A1278Revision 1: January 07, 2010
15 of 83

### Page 16

DESCRIPTIONCONFIGURATIONGROUP
737-100/200 Airplanes delivered with grease fittings on the Stabilizer
Trim Actuator Ball Nut.
-3
Airplane Models:
737-100, 737-200, 737-200C, 737-300, 737-400, 737-500
GroupVariable Number
2PA001 - PA022
2PA099
2PA231 - PA232
2PC001 - PC005
2PG001 - PG004
3PG005
2PG006 - PG075
2PG199
2PG201 - PG230
2PG251 - PG255
2PG271 - PG279
2PG301 - PG314
2PG331 - PG332
2PG351 - PG356
2PG375
2PG401 - PG403
2PG431 - PG442
2PG471 - PG475
2PG501 - PG505
2PG571 - PG586
2PG621 - PG630
2PG651 - PG652
2PG701 - PG705
2PH001
2PH011 - PH013
3PH021 - PH024
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: May 24, 2007
737-27A1278Revision 1: January 07, 2010
16 of 83
BOEING SERVICE BULLETIN 737-27A1278
ALERTALERT

### Page 17

GroupVariable Number
2PH701 - PH714
3PH715
2PH731 - PH732
2PH741 - PH743
2PJ001 - PJ003
3PJ004 - PJ009
2PJ031 - PJ032
2PJ071 - PJ072
2PJ101 - PJ109
3PJ110 - PJ119
2PJ201 - PJ216
3PJ217 - PJ219
1PJ301 - PJ302
1PJ551 - PJ561
1PJ601 - PJ615
1PJ811
1PJ816 - PJ817
2PK026 - PK027
3PK028 - PK029
2PK041 - PK044
3PK045 - PK053
3PK061 - PK070
3PK081 - PK082
3PK091 - PK099
3PK101 - PK103
3PK111 - PK120
3PK141 - PK146
3PK201 - PK204
3PK211 - PK223
3PK231 - PK241
3PK251 - PK258
3PK271 - PK274
3PK281 - PK289
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: May 24, 2007
737-27A1278Revision 1: January 07, 2010
17 of 83
BOEING SERVICE BULLETIN 737-27A1278
ALERTALERT

### Page 18

GroupVariable Number
3PK291
3PK301 - PK318
3PK341
3PK351 - PK361
3PK391
3PK431 - PK433
3PK451 - PK452
3PK461 - PK469
3PK495
3PK501 - PK504
3PK511 - PK515
3PK519
3PK521 - PK528
3PK541 - PK565
3PK581
3PK591 - PK599
3PK601 - PK617
3PK621 - PK637
3PK641 - PK642
3PK661 - PK666
3PK671 - PK681
3PK691 - PK697
3PK711 - PK716
3PK731 - PK765
3PK771 - PK779
3PK801 - PK804
3PK819 - PK827
3PK830
3PK861 - PK863
3PK871 - PK874
3PK881 - PK884
3PK901 - PK938
3PK971 - PK974
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: May 24, 2007
737-27A1278Revision 1: January 07, 2010
18 of 83
BOEING SERVICE BULLETIN 737-27A1278
ALERTALERT

### Page 19

GroupVariable Number
3PL001 - PL028
3PL061
3PL081
3PL101 - PL113
3PL151
3PL171 - PL172
3PL201 - PL203
3PL221
3PL401 - PL417
3PL421
3PL441
3PL451 - PL456
3PL471
3PL491
3PL501 - PL506
3PL551 - PL562
3PL581
3PL601 - PL603
3PL611
3PL621 - PL626
3PL631 - PL632
2PL711 - PL712
2PL716 - PL717
3PL718 - PL725
2PL726 - PL729
3PL730 - PL735
2PL736 - PL742
3PL743 - PL747
2PL756
3PL758
2PL761 - PL763
3PL764 - PL770
2PL781 - PL782
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: May 24, 2007
737-27A1278Revision 1: January 07, 2010
19 of 83
BOEING SERVICE BULLETIN 737-27A1278
ALERTALERT

### Page 20

GroupVariable Number
3PL783 - PL788
2PL793
2PL801 - PL803
3PM001 - PM006
3PM016 - PM017
3PM021 - PM023
3PM051 - PM065
1PM066
3PM101 - PM119
3PM141 - PM142
3PM171
3PM181
3PM251 - PM255
1PM281
3PM282 - PM283
1PM381 - PM399
1PM401 - PM417
1PM541 - PM564
3PN001 - PN002
3PN021 - PN043
3PN081 - PN086
3PN101 - PN117
3PN131 - PN163
3PN401 - PN420
3PN431 - PN433
3PN451 - PN456
3PN471 - PN474
3PN481
3PN491 - PN493
3PN501 - PN502
3PN511 - PN512
3PN521
1PP001 - PP054
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: May 24, 2007
737-27A1278Revision 1: January 07, 2010
20 of 83
BOEING SERVICE BULLETIN 737-27A1278
ALERTALERT

### Page 21

GroupVariable Number
1PP101 - PP169
1PP181 - PP199
1PP201 - PP205
1PP221
1PP231 - PP243
1PP281 - PP286
1PP301 - PP305
1PP351 - PP353
1PP376 - PP384
1PP391 - PP393
1PP401 - PP440
1PP471 - PP475
1PP501 - PP522
1PP631 - PP634
1PP651 - PP652
1PP671 - PP699
1PP701 - PP733
1PP771 - PP779
1PP801 - PP808
1PP821 - PP827
1PP831 - PP848
1PP851 - PP852
1PP861 - PP877
1PP891 - PP899
1PP901 - PP936
1PP946 - PP948
1PP951 - PP952
1PP961 - PP967
1PP981 - PP991
1PP993
1PQ001 - PQ016
1PQ026 - PQ041
1PQ051 - PQ092
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: May 24, 2007
737-27A1278Revision 1: January 07, 2010
21 of 83
BOEING SERVICE BULLETIN 737-27A1278
ALERTALERT

### Page 22

GroupVariable Number
1PQ101 - PQ199
1PQ201 - PQ202
1PQ221 - PQ237
1PQ241 - PQ243
1PQ251 - PQ267
1PQ281 - PQ299
1PQ301 - PQ307
1PQ331 - PQ332
1PQ341 - PQ348
1PQ361 - PQ373
1PQ391 - PQ395
1PQ401 - PQ418
1PQ421
1PQ431 - PQ438
1PQ447 - PQ448
1PQ451
1PQ454
1PQ471 - PQ475
1PQ479 - PQ481
1PQ486 - PQ487
1PQ491 - PQ493
1PQ771 - PQ772
1PQ791 - PQ793
1PQ801 - PQ805
1PQ931 - PQ935
1PQ951
1PQ971 - PQ997
1PR001 - PR017
1PR021 - PR034
1PR041 - PR045
1PR061 - PR072
1PR077 - PR082
1PR091 - PR092
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: May 24, 2007
737-27A1278Revision 1: January 07, 2010
22 of 83
BOEING SERVICE BULLETIN 737-27A1278
ALERTALERT

### Page 23

GroupVariable Number
1PR096
1PR101
1PR121 - PR122
1PR131 - PR132
1PR141 - PR143
1PR161 - PR172
1PR181
1PS601 - PS631
1PS636 - PS638
1PS641 - PS644
1PS651 - PS657
1PS666 - PS669
1PS691 - PS692
1PS701 - PS706
1PS751 - PS799
1PS811
1PS836 - PS837
1PS841 - PS846
1PS851 - PS852
1PS856
1PS861 - PS863
1PS866 - PS868
1PS871 - PS874
1PS896 - PS897
1PS901 - PS941
1PS956 - PS957
1PS961 - PS963
1PS971 - PS978
1PT001 - PT015
1PT021 - PT031
1PT041 - PT064
1PT101 - PT105
1PT121 - PT138
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: May 24, 2007
737-27A1278Revision 1: January 07, 2010
23 of 83
BOEING SERVICE BULLETIN 737-27A1278
ALERTALERT

### Page 24

GroupVariable Number
1PT146 - PT148
1PT161 - PT170
1PT181 - PT188
1PT211 - PT220
1PT295
1PT301 - PT309
1PT331 - PT360
1PT381 - PT399
1PT401 - PT438
1PT501 - PT517
1PT561 - PT565
1PT581 - PT586
1PT611 - PT621
1PT641 - PT644
1PT651 - PT656
1PT671 - PT672
1PT681 - PT685
1PT701 - PT703
1PT716 - PT717
1PT721 - PT725
1PT801 - PT834
1PT851 - PT854
1PT871 - PT886
1PT901 - PT930
1PT971 - PT973
1PT981 - PT985
1PT996
1PU001 - PU025
1PU301
1PU311 - PU313
1PV001 - PV055
1PV201 - PV209
1PV226 - PV229
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: May 24, 2007
737-27A1278Revision 1: January 07, 2010
24 of 83
BOEING SERVICE BULLETIN 737-27A1278
ALERTALERT

### Page 25

GroupVariable Number
1PV231 - PV237
1PV271 - PV272
1PV281 - PV287
1PV296
1PV301 - PV302
1PV351
1PV356 - PV357
1PW001 - PW054
1PW061 - PW068
1PW072
1PW086 - PW088
1PW091 - PW094
1PW101 - PW102
1PW106
1PW111 - PW120
1PW156 - PW157
1PW161 - PW171
1PW201 - PW252
1PW261 - PW268
1PW271 - PW276
1PW278
1PW281 - PW293
1PW296
1PW301 - PW327
1PW401 - PW408
1PW411 - PW418
1PW421 - PW424
1PW431 - PW435
1PW441 - PW450
1PW461 - PW467
1PW501 - PW504
1PW511 - PW522
1PW524 - PW550
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: May 24, 2007
737-27A1278Revision 1: January 07, 2010
25 of 83
BOEING SERVICE BULLETIN 737-27A1278
ALERTALERT

### Page 26

GroupVariable Number
1PW556 - PW557
1PW561 - PW564
1PW571 - PW576
1PW591 - PW596
1PW611 - PW622
1PW631 - PW637
1PW661 - PW662
1PW681 - PW683
1PW701 - PW702
1PW711 - PW717
1PW741 - PW742
1PW761
1PW771
1PW831
1PW851 - PW856
2PX071
2PX701
2PY001 - PY008
2PY021 - PY022
2PY031
2PY036 - PY037
2PY046 - PY047
3PY048
2PY051 - PY052
3PY053
3PY056 - PY057
2PY101
3PY102 - PY103
2PY111 - PY113
2PY131
3PY132 - PY135
3PY141 - PY143
3PY151 - PY154
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: May 24, 2007
737-27A1278Revision 1: January 07, 2010
26 of 83
BOEING SERVICE BULLETIN 737-27A1278
ALERTALERT

### Page 27

GroupVariable Number
3PY156 - PY157
3PY161 - PY162
3PY166
3PY191
3PY201
3PY221 - PY222
3PY231
3PY241 - PY244
3PY270 - PY275
3PY281
3PY286
2PY301 - PY304
2PY321 - PY323
2PY341 - PY346
2PY361 - PY362
2PY381
3PY401
3PY409 - PY411
3PY421 - PY422
3PY441
3PY451
3PY461 - PY463
3PY591 - PY595
3PY611 - PY612
3PY621
3PY631
3PY651
3PY671 - PY672
3PY721
3PY741
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: May 24, 2007
737-27A1278Revision 1: January 07, 2010
27 of 83
BOEING SERVICE BULLETIN 737-27A1278
ALERTALERT

### Page 28

2. Spares Affected
Examine your spares supply for Stabilizer Ballscrew Assembly part numbers given in the tables
below and incorporate the applicable supplier service bulletin to make sure that you do not install
Ballscrew Assemblies that are not reworked on airplanes that incorporated the applicable supplier
service bulletin:
Boeing Part Num-
ber
Umbra Cuscinetti,
S.p.A., Part Number
Name
10-62210-207322P000-01 (a)Stabilizer Ballscrew
Assy
10-62210-307322P000-02 (a)Stabilizer Ballscrew
Assy
(a) Incorporate Service Bulletin UMBRA CUSCINETTI, S.p.A.
SB 07322-27-01 on these Ballscrew assemblies prior to in-
stalling the Horizontal Stabilizer Trim Actuator with the spare
Ballscrew Assembly on the airplane, if the Horizontal Stabi-
lizer Trim Actuator removed had a Ballscrew Assembly with
the UMBRA CUSCINETTI, S.p.A. SB 07322-27-01 incorpo-
rated.
Boeing Part Num-
ber
Linear Motion, LLC
Part Number
Name
10-61302-354032-003 (a)Stabilizer Ballscrew
Assy
10-61302-454032-004 (a)Stabilizer Ballscrew
Assy
10-61302-354032-005 (a)Stabilizer Ballscrew
Assy
10-61302-354032-006 (a)Stabilizer Ballscrew
Assy
10-61302-57826837 (a)Stabilizer Ballscrew
Assy
(a) Incorporate Service Bulletin LINEAR MOTION, LLC SB
7901708 on these Ballscrew assemblies prior to installing
the Horizontal Stabilizer Trim Actuator with the spare
Ballscrew Assembly on the airplane, if the Horizontal Stabi-
lizer Trim actuator removed had a Ballscrew Assembly with
the LINEAR MOTION, LLC SB 7901708 incorporated.
Boeing Part Num-
ber
Skytronics, Inc.
Part Number
Name
10-61302-2102J033-501 (.6250)
(a)
Stabilizer Ballscrew
Assy
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: May 24, 2007
737-27A1278Revision 1: January 07, 2010
28 of 83
BOEING SERVICE BULLETIN 737-27A1278
ALERTALERT

### Page 29

Boeing Part Num-
ber
Skytronics, Inc.
Part Number
Name
10-61302-2102J033-501 (.6243)
(a)
Stabilizer Ballscrew
Assy
10-61302-2102J033-5 (a)Stabilizer Ballscrew
Assy
10-61302-2 (b)102J033-3 (a) (b)Stabilizer Ballscrew
Assy
10-61302-1102J033-1 (c)Stabilizer Ballscrew
Assy
10-61302-1102J033-1 (OS) (c)Stabilizer Ballscrew
Assy
(a) Incorporate Service Bulletin SKYTRONICS, Inc. SB 93004
on these Ballscrew assemblies prior to installing the Horizon-
tal Stabilizer Trim Actuator with the spare Ballscrew Assembly
on the airplane, if the Horizontal Stabilizer Trim Actuator re-
moved had a Ballscrew Assembly with the SKYTRONICS,
Inc. SB 93004 incorporated.
(b) The Ballscrew Actuator Assy P/N 102J033-3 became Boeing
P/N 10-61302-2 at the incorporation of Boeing Service Bul-
letin 737-27-1046 Revision 1 dated July, 1974.
(c) The Horizontal Stabilizer Trim Actuator Ballscrew Assembly
102J033-1 or 102J033-1 (OS) with Oil Lubricator can not be
reworked to a Horizontal Stabilizer Trim Actuator Ballscrew
Assembly with grease lubrication fitting as given in Boeing
Service Bulletin 737-27-1046 Revision 1.
B. Concurrent Requirements
None.
C. Reason
This service bulletin is being issued to maintain the frequency of the detailed inspection of the Horizontal
Stabilizer Trim Actuator Ballscrew and Ball Nut as specified in the Maintenance Planning Document.
This service bulletin also gives instructions to remove/replace and repair the Horizontal Stabilizer Trim
Actuator if a damaged Ballscrew or Ball Nut is found. This service bulletin also adds the recommended
intervals for repeat lubrication and overhaul. Also, this service bulletin gives recommended compliance
time for incorporation of the suppliers service bulletins (service bulletin UMBRA CUSCINETTI, S.p.A.
SB 07322-27-01, service bulletin LINEAR MOTION, LLC SB 7901708, and service bulletin
SKYTRONICS, Inc. SB 93004). The UMBRA CUSCINETTI supplier service bulletin provides instructions
to remove and replace the Ball Nut Tube Retainers on the 737 Horizontal Stabilizer Trim Actuator
Ballscrew assembly with new Tube Retainers. The LINEAR MOTION supplier service bulletin provides
instructions to remove and replace the Ball Deflectors and the Ball Return Guide Clamps on 737
Horizontal Stabilizer Trim Actuator Ballscrew assembly with new Ball Deflectors and Ball Return Guide
Clamps. The SKYTRONICS supplier service bulletin provides instructions to remove and replace the
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: May 24, 2007
737-27A1278Revision 1: January 07, 2010
29 of 83
BOEING SERVICE BULLETIN 737-27A1278
ALERTALERT

### Page 30

Return Tube Clamps on the 737 Horizontal Stabilizer Trim Actuator Ballscrew assembly with new
Return Tube Clamps. The new parts installed will have sufficient stiffness to retain the load carrying
balls in all known failure mode conditions. The changes given in this bulletin will reduce the probability
of loss of the primary and secondary load paths of the Stabilizer Trim Actuator. Loss of primary and
secondary load paths of the Stabilizer Trim Actuator could result in the loss of control of the airplane.
This Service Bulletin also specifies the time for incorporation of the Boeing Service Bulletin 737-27-1046
Revision 1 (as applicable), dated April 5, 1974, if the service bulletin is not already incorporated. Boeing
Service Bulletin 737-27-1046 Revision 1 applies to airplanes 737-100/200 with oil lubricators and
provides instructions for removing the existing oil lubricators and installation of a grease fitting on the
Stabilizer Trim Actuator Ball Nut.
NOTE: The Horizontal Stabilizer Trim Actuator Ballscrew Assembly 102J033-1 or 102J033-1 (OS)
with Oil Lubricator can not be reworked to a Horizontal Stabilizer Trim Actuator Ballscrew
Assembly with grease lubrication fitting as given in Boeing Service Bulletin 737-27-1046
Revision 1. Remove these Stabilizer Trim Actuator Ballscrew Assemblies with Oil Lubricator
and install 102J033-3 or 102J033-502 or Horizontal Stabilizer Trim Actuator Ballscrew
Assembly.
This service bulletin is being issued to maintain the frequency of the detailed visual inspection of the
Horizontal Stabilizer Trim Actuator Ballscrew and Ball Nut as specified in the Maintenance Planning
Document. This service bulletin also gives instructions to remove/replace and repair the Horizontal
Stabilizer Trim Actuator if a damaged Ballscrew or Ball Nut is found. This service bulletin also adds the
recommended intervals for repeat lubrication and overhaul.
NOTE: Boeing also recommends that the Maintenance Planning Document (MPD) intervals be
observed for the "Lubrication" and "Detailed Inspection" actions prior to compliance with this
service bulletin. The "Lubrication" and "Detailed Inspection" done as given in this service
bulletin satisfy the "Lubrication" and "Detailed Inspection" requirements given in Maintenance
Planning Document" (MPD).
Boeing Service Related Problem (SRP) 737CL-SRP-27-0153 is related to this bulletin.
Revision 1 is sent to correct the work instructions for the HSTA name plate identification information
in WORK PACKAGE 4 and to clarify some of the inspections necessary in WORK PACKAGE 1 and
WORK PACKAGE 2. A note is also added in the compliance table to advise operators to do the
lubrication task during the detailed inspection task. In addition, reference to the "Horizontal Stabilizer
Gearbox End Play Test as given OHM 27-45-11" is added. This is because the Horizontal Stabilizer
Gearbox Backlash Inspection is only given in the AMM for 737-600/700/800/900 airplane. The (OHM)
Horizontal Stabilizer Gearbox End Play Test is a similar test and is applicable to all
737-100/200/300/400/500 airplane variants.
1. Paragraph 1.D., Description: Affected Maintenance Zones are added for each airplane group.
2. Paragraph 1.E., Compliance: Notes (a) and (b) are added to Table 1 and Table 2 to recommend
operators to do a lubrication task during the detailed inspection task.
3. Paragraph 1.E., Compliance: Notice of Propose Rule Making 2007-NM-256-AD is added.
4. Paragraph 1.K., Publications Affected: Added Damage Tolerance Based Structural Inspection
statement.
5. Paragraph 3.A., General Information: General Visual Inspection note added.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: May 24, 2007
737-27A1278Revision 1: January 07, 2010
30 of 83
BOEING SERVICE BULLETIN 737-27A1278
ALERTALERT

### Page 31

6. Paragraph 3.B., Work Instructions:
a. WORK PACKAGE 1:
– Added some notes, added more data to some step instructions, deleted some unnecessary
step instruction and correctly re-sequenced the steps.
b. WORK PACKAGE 2:
– Added some notes, added more data to some step instructions, deleted some unnecessary
step instruction and correctly re-sequenced the steps.
c. WORK PACKAGE 4:
– Step 1.a. revised to reference SB 737-27A1278 WORK PACKAGE 4 instead of
737-27A1278 WORK PACKAGE 3.
– Step 2.a. revised to reference SB 737-27A1278 WORK PACKAGE 4 instead of
737-27A1278 WORK PACKAGE 3.
– Step 3.b. revised to reference SB 737-27A1278 WORK PACKAGE 4 instead of
737-27A1278 WORK PACKAGE 3.
7. FIGURE 1: Step 10, inspection for large amount of grease that exits the Ball Nut and note (a) are
removed.
8. FIGURE 2: Step 10, inspection for large amount of grease that exits the Ball Nut and note (a) are
removed.
9. FIGURE 7 sheet 2: Step 4, reference to Aircraft Maintenance Manual (AMM) removed and replaced
with internal reference note (b). Also the step table note (b) is revised to reference Horizontal
Stabilizer Gearbox End Play Test as given in OHM 27-45-11 instead of the Horizontal Stabilizer
Gearbox Backlash inspection as given in AMM 27-41-81/606.
10. FIGURE 8 sheet 2: Step 4, reference to Aircraft Maintenance Manual (AMM) removed and replaced
with internal reference note (b). Also the step table note (b) is revised to reference Horizontal
Stabilizer Gearbox End Play Test as given in OHM 27-45-11 instead of the Horizontal Stabilizer
Gearbox Backlash inspection as given in AMM 27-41-81/606.
11. FIGURE 9 sheet 2: Step 4, reference to Aircraft Maintenance Manual (AMM) removed and replaced
with internal reference note (b). Also the step table note (b) is revised to reference Horizontal
Stabilizer Gearbox End Play Test as given in OHM 27-45-11 instead of the Horizontal Stabilizer
Gearbox Backlash inspection as given in AMM 27-41-81/606.
D. Description
Get access to the Horizontal Stabilizer Trim Actuator and do the procedures that follow below at the
intervals shown in the compliance section.
1. DETAILED INSPECTION:
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: May 24, 2007
737-27A1278Revision 1: January 07, 2010
31 of 83
BOEING SERVICE BULLETIN 737-27A1278
ALERTALERT

### Page 32

– Do a detailed inspection for metal particles or corrosion products in the grease on the actuator
Ball Nut and Ballscrew. Clean the actuator Ballscrew. Visually inspect the actuator Ball Nut
and Ballscrew for damage, cracks, corrosion, and worn areas. Inspect for grease leakage.
Inspect for lifted or damaged Ball Nut Tube Retainers (UMBRA CUSCINETTI, S.p.A Ballscrew
Assemblies), or Ball Return Guide Clamps (LINEAR MOTION Ballscrew Assemblies), or
Return Tube Clamps (SKYTRONICS, Ballscrew Assemblies). Inspect the external areas of
the Stabilizer Trim Actuator, and the areas below the Stabilizer Trim Actuator, for loose ball
bearings. Move the Horizontal Stabilizer to a different setting to get access to the Ballscrew
area covered by the Ball Nut during the previous inspection. Repeat the inspections for the
new exposed area of the ballscrew. Replace the Horizontal Stabilizer Trim Actuator before
further flight if any of these conditions exist.
– Do the Detailed Inspection as given in Accomplishment Instructions, Paragraph 3.B., Work
Instructions, WORK PACKAGE 1 or WORK PACKAGE 2 (as applicable).
LUBRICATE THE HORIZONTAL STABILIZER TRIM ACTUATOR:
– Lubricate the Horizontal Stabilizer Trim Actuator Ballscrew, Ball Nut, and the upper and lower
Gimbals.
– Do the Lubrication as given in Accomplishment Instructions, Paragraph 3.B., Work Instructions,
WORK PACKAGE 1 or WORK PACKAGE 2 (as applicable).
REMOVE and REPAIR or REPLACE THE HORIZONTAL TRIM ACTUATOR: Remove/Replace
the Horizontal Stabilizer Trim Actuator if damage is found as given in Accomplishment Instructions,
Paragraph 3.B., Work Instructions, WORK PACKAGE 1 or WORK PACKAGE 2 (as applicable).
NOTE: As an option, Operators can replace a damaged Horizontal Stabilizer Trim Actuator with
a serviceable Stabilizer Trim Actuator that is not new or not overhauled. Before the next
flight, do the Detailed Inspection and Lubrication for the replacement Stabilizer Trim
Actuator as given in this service bulletin and do the End Play Test as given in OHM
27-45-11. After the installation follow the requirements of this service bulletin.
2. For airplanes with Horizontal Stabilizer Trim Actuator Ballscrew Assemblies with Oil Lubricators:
a. CHECK the Horizontal Stabilizer Trim Actuator Ballscrew Assy Part Number. If you find
Horizontal Stabilizer Trim Actuator Ballscrew Assemblies 102J033-1 (Boeing Part Number
10-61302-1) or 102J033-1 (OS) (Boeing Part Number 10-61302-1), remove and install Stabilizer
Ballscrew Assy 102J033-3 (Boeing Part Number 10-61302-2) or 102J033-502 (Boeing Part
Number 10-61302-7) as given in Accomplishment Instructions, Paragraph 3.B., Work
Instructions, WORK PACKAGE 3.
NOTE: The Horizontal Stabilizer Trim Actuator Ballscrew Assembly 102J033-1 or 102J033-1
(OS) with Oil Lubricator can not be reworked to a Horizontal Stabilizer Trim Actuator
Ballscrew Assembly with grease lubrication fitting as given in Service Bulletin. The
102J033-3 (Boeing Part Number 10-61302-2) is an oil lubricated Horizontal Stabilizer
Trim Actuator Ballscrew Assembly and operators have to incorporate Boeing Service
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: May 24, 2007
737-27A1278Revision 1: January 07, 2010
32 of 83
BOEING SERVICE BULLETIN 737-27A1278
ALERTALERT

### Page 33

Bulletin 737-27-1046 Revision 1 and the Service Bulletin SKYTRONICS, Inc. SB
93004. The 102J033-502 (Boeing Part Number 10-61302-7) is a grease lubricated
Horizontal Stabilizer Trim Actuator Ballscrew Assembly with reinforced Return Tube
Clamps, and Operators do not have to incorporate Boeing Service bulletin
737-27-1046 Revision 1 and Service Bulletin SKYTRONICS, Inc. SB 93004.
b. INCORPORATE BOEING SB 737-27-1046 Revision 1 as applicable: Incorporate SB
737-27-1046 Revision 1 as given in Accomplishment Instructions, Paragraph 3.B., Work
Instructions, WORK PACKAGE 3.
NOTE: Service Bulletin 737-27-1046 Revision 1 is applicable for some 737-100/200 airplanes
with Ballscrew Oil Lubricators. This Service Bulletin provides instructions for the
removal of the existing Oil Lubricators and the installation of a grease fitting on the
Horizontal Stabilizer Trim Actuator Ball Nut. The Horizontal Stabilizer Trim Actuator
Ballscrew Assembly 102J033-1 or 102J033-1 (OS) with Oil Lubricator can not be
reworked to a Horizontal Stabilizer Trim Actuator Ballscrew Assembly with grease
lubrication fitting.
3. INCORPORATE ONE OF THE FOLLOWING SUPPLIER SERVICE BULLETINS as given in
Accomplishment Instructions, Paragraph 3.B., Work Instructions, WORK PACKAGE 4:
– Service Bulletin UMBRA CUSCINETTI, S.p.A. SB 07322-27-01, Rev 00, Dated December
21, 2004: Install the new Ball Nut Tube Retainers as given in this supplier service bulletin.
– Service Bulletin LINEAR MOTION, LLC SB 7901708, Dated July 26, 2005: Install the new
Ball Deflectors and Ball Return Guide Clamps as given in this supplier service bulletin.
– Service Bulletin SKYTRONICS, Inc. SB 93004, Dated September 01, 2005: Install the new
Return Tube Clamps as given in this supplier service bulletin.
4. REMOVE AND REPAIR/OVERHAUL THE HORIZONTAL STABILIZER TRIM ACTUATOR:
– Remove and repair/overhaul the Horizontal Stabilizer Trim Actuator as given in Paragraph
3.B., Work Instructions, WORK PACKAGE 5.
PLEASE SEND THE RESULTS FOR THE FAILED INSPECTIONS TO BOEING.
Send your report to: BOEING COMMERCIAL AIRPLANES GROUP ATTENTION: MANAGER, SERVICE
BULLETIN ENGINEERING P.O. BOX 3707, MAIL CODE 2H-36 SEATTLE, WA 98124-2207 USA
Revision 1:
No more work is necessary on airplanes changed as shown in the original issue of this service bulletin.
However, Operators have to continue to do the repeat Detailed Inspection, Lubrication, and Overhaul
as given in Paragraph 1.E., Compliance, Table 1 or Table 2 as applicable.
NOTE: The Operators that performed the initial Detailed Inspection, Lubrication, and Overhaul do
not have to do another initial inspection, but have to continue to do the repeat Detailed
Inspection, Lubrication, and Overhaul of the Horizontal Stabilizer Trim Actuator as given in
Paragraph 1.E., Compliance, Table 1 or Table 2 as applicable.
The Operators that incorporated service bulletin UMBRA CUSCINETTI, S.p.A. SB 07322-27-01
as given in WORK PACKAGE 4, have to continue to do the repeat Detailed Inspection,
Lubrication, and Overhaul of the Horizontal Stabilizer Trim Actuator as given in Paragraph
1.E., Compliance, Table 1 or Table 2 as applicable.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: May 24, 2007
737-27A1278Revision 1: January 07, 2010
33 of 83
BOEING SERVICE BULLETIN 737-27A1278
ALERTALERT

### Page 34

The Operators that did not incorporate Service Bulletin UMBRA CUSCINETTI, S.p.A. SB
07322-27-01, have to incorporate Service Bulletin UMBRA CUSCINETTI, S.p.A. SB
07322-27-01 as given in WORK PACKAGE 4, and have to continue to do the repeat Detailed
Inspection, Lubrication, and Overhaul of the Horizontal Stabilizer Trim Actuator as given in
Paragraph 1.E., Compliance, Table 1 or Table 2 as applicable.
The work in this service bulletin is done in the maintenance zone(s) given below.
Group 1:
Affected Maintenance Zones
ZoneModel
7-2737-200
Group 1:
Affected Maintenance Zones
ZoneModel
702737-300, 737-400, 737-500
Group 2:
Affected Maintenance Zones
ZoneModel
7-2737-100, 737-200, 737-200C
Group 3:
Affected Maintenance Zones
ZoneModel
7-2737-200, 737-200C
E. Compliance
Boeing recommends that the operators do this service bulletin at the time given in Table 1 or Table 2,
as applicable.
NOTE: Boeing also recommends that the Maintenance Planning Document (MPD) intervals be
observed for the "Lubrication" and "Detailed Inspection" actions prior to compliance with this
service bulletin. The "Lubrication" and "Detailed Inspection" done as given in this service
bulletin satisfy the "Lubrication" and "Detailed Inspection" requirements given in Maintenance
Planning Document" (MPD).
Federal Aviation Administration (FAA) Notice of Proposed Rule Making FAA NPRM 2007-NM-256-AD,
is related to this service bulletin.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: May 24, 2007
737-27A1278Revision 1: January 07, 2010
34 of 83
BOEING SERVICE BULLETIN 737-27A1278
ALERTALERT

### Page 35

Group 1; Group 2, Configuration 1; Group 3:
Table 1 - Inspection, Lubrication, and Overhaul of the Horizontal Stabilizer Trim Actuator; Incorporation
of UMBRA CUSCINETTI, S.p.A. 07322-27-01 Service Bulletin, LINEAR MOTION, LLC 7901708 Service
Bulletin, and SKYTRONICS, Inc. 93004 Service Bulletin
NotesRepeat IntervalCompliance Time
(Whichever Occurs First)
ActionCondition
(a)4,000 Flight Hours or
2 years (Whichever
Occurs First).
Within 4,000 Flight Hours or
18 months from the last De-
tailed Inspection.
Detailed Inspection in
accordance with Para-
graph 3.B., Work In-
structions Steps 1.e.
and 1.o. WORK PACK-
AGE 1.
Group 1, Group 2
Configuration 1, and
Group 3 airplanes
(b)2,000 Flight Hours or
1 year (Whichever
Occurs First).
Within 2,000 Flight Hours or
1 Year from the last Lubrica-
tion.
Lubricate in accor-
dance with Paragraph
3.B., Work Instructions
Step 1.p., WORK
PACKAGE 1.
24,000 Flight Hours
(Not to Exceed).
Before the accumulation of
24,000 Flight Hours since the
date of issuance of the origi-
nal standard airworthiness
certificate or the date of is-
suance of the original export
certificate of airworthiness, or
within 24,000 Flight Hours
since last HSTA Overhaul.
Horizontal Stabilizer
Trim Actuator Overhaul
in accordance with Ac-
complishment Instruc-
tions, Paragraph 3.B.,
Work Instructions,
WORK PACKAGE 5.
-Before the accumulation of
24,000 Flight Hours since the
date of issuance of the origi-
nal standard airworthiness
certificate or the date of is-
suance of the original export
certificate of airworthiness, or
within 24,000 Flight Hours
since last HSTA Overhaul.
Incorporate Service
Bulletin UMBRA CUS-
CINETTI, S.p.A. SB
07322-27-01, or Ser-
vice Bulletin LINEAR
MOTION, LLC SB
7901708, or Service
Bulletin SKYTRONICS,
Inc. SB 93004, as appli-
cable, in accordance
with Accomplishment
Instructions, Paragraph
3.B., Work Instructions,
WORK PACKAGE 4.
-Before further flightRepair/Replace the
Horizontal Stabilizer
Trim Actuator in accor-
dance with Accomplish-
ment Instructions,
Paragraph 3.B., Work
Instructions, WORK
PACKAGE 5.
Group 1, Group 2
Configuration 1, and
Group 3 airplanes
with damaged Hori-
zontal Stabilizer
Trim Actuator
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: May 24, 2007
737-27A1278Revision 1: January 07, 2010
35 of 83
BOEING SERVICE BULLETIN 737-27A1278
ALERTALERT

### Page 36

Group 1; Group 2, Configuration 1; Group 3:
Table 1 - Inspection, Lubrication, and Overhaul of the Horizontal Stabilizer Trim Actuator; Incorporation
of UMBRA CUSCINETTI, S.p.A. 07322-27-01 Service Bulletin, LINEAR MOTION, LLC 7901708 Service
Bulletin, and SKYTRONICS, Inc. 93004 Service Bulletin
NotesRepeat IntervalCompliance Time
(Whichever Occurs First)
ActionCondition
(a) This task accomplishes a detailed inspection of the Horizontal Stabilizer Trim Actuator Ballscrew, Ball
Nut, Ball Nut Tube Retainers and Return Tubes, and also accomplishes a detailed inspection of the
lower and upper Gimbal and the attachment points. The detailed inspection done in accordance with
the service bulletin partially satisfies the intent of the task in accordance with 737-200 MPD Volume 1
Section 4 Item Number 4-27-06, or 737-300/400/500 MPD Volume 1 Section 6, Item Number B27-00-
00-F. You must accomplish the detailed inspection of the Horizontal Stabilizer Trim actuator as given
in this service bulletin to establish and stay compliant with this service bulletin.
(b) Accomplishment of this task satisfies the intent of the task in accordance with 737-200 MPD Volume
1 Section 3 Item Number 3-05-01, or 737-300/400/500 MPD Volume 1 Section 6, Item Number B12-
22-41-3A. However, you must accomplish this task as given in this service bulletin to establish and
stay compliant with this service bulletin.
Group 2, Configuration 2:
Table 2 - Inspection, Lubrication, and Overhaul of the Horizontal Stabilizer Trim Actuator; Incorporation
of 737-27-1046 Boeing Service Bulletin, and SKYTRONICS, Inc. 93004 Service Bulletin
NotesRepeat IntervalCompliance Time
(Whichever Occurs First)
ActionCondition
(d)2,000 Flight Hours or 1
year (Whichever occurs
first).
Within 2,000 Flight Hours
or 1 year from the last in-
spection.
Detailed Inspection in accor-
dance with Accomplishment
Instruction, Paragraph 3.B.,
Work Instructions, Steps 1.e.
and 1.o., WORK PACKAGE
2.
Group 2, Config-
uration 2 air-
planes
(e)500 Flight Hours or 2
months (whichever oc-
curs first).
Within 500 Flight Hours or
2 months from the last Lu-
brication.
Lubricate in accordance with
Accomplishment Instruction,
Paragraph 3.B., Work In-
structions, Step 1.p., WORK
PACKAGE 2.
20,000 Flight Hours (Not
To Exceed).
Before the accumulation of
20,000 Flight Hours since
the date of issuance of the
original standard airworthi-
ness certificate or the date
of issuance of the original
export certificate of airwor-
thiness, or within 20,000
Flight Hours since last HS-
TA overhaul.
Horizontal Stabilizer Trim
Actuator Overhaul in accor-
dance with Accomplishment
Instructions, Paragraph 3.B.,
Work Instructions, WORK
PACKAGE 5.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: May 24, 2007
737-27A1278Revision 1: January 07, 2010
36 of 83
BOEING SERVICE BULLETIN 737-27A1278
ALERTALERT

### Page 37

Group 2, Configuration 2:
Table 2 - Inspection, Lubrication, and Overhaul of the Horizontal Stabilizer Trim Actuator; Incorporation
of 737-27-1046 Boeing Service Bulletin, and SKYTRONICS, Inc. 93004 Service Bulletin
NotesRepeat IntervalCompliance Time
(Whichever Occurs First)
ActionCondition
-Before further flightRepair/Replace the Horizon-
tal Stabilizer Trim Actuator
in accordance with Accom-
plishment Instructions,
Paragraph 3.B., Work In-
structions, WORK PACK-
AGE 5.
Group 2 Configu-
ration 2 air-
planes with
damaged Hori-
zontal Stabilizer
Trim Actuator
(a)-Before the accumulation of
20,000 Flight Hours since
the date of issuance of the
original standard airworthi-
ness certificate or the date
of issuance of the original
export certificate of airwor-
thiness, or within 20,000
Flight Hours since last HS-
TA overhaul.
Remove the Stabilizer
Ballscrew Assy 102J033-1
or 102J033-1 (OS) and in-
stall Stabilizer Ballscrew As-
sy 102J033-3 or 102J033-
502 in accordance with Ac-
complishment Instructions,
Paragraph 3.B., Work In-
structions, WORK PACK-
AGE 3.
Group 2 Configu-
ration 2 air-
planes with Stabi-
lizer Trim Actua-
tor Ballscrew As-
sy 102J033-1 or
102J033-1 (OS)
installed on the
airplane.
(a) (b)
(c)
-Before the accumulation of
20,000 Flight Hours since
the date of issuance of the
original standard airworthi-
ness certificate or the date
of issuance of the original
export certificate of airwor-
thiness, or within 20,000
Flight Hours since last HS-
TA overhaul.
Incorporate Boeing Service
Bulletin 737-27-1046 Revi-
sion 1 in accordance with
Accomplishment Instruc-
tions, Paragraph 3.B., Work
Instructions, WORK PACK-
AGE 3.
Group 2, Config-
uration 2 air-
planes with Hori-
zontal Stabilizer
Trim Actuator
Ballscrew Assy
with Oil Lubrica-
tors
(a)-Before the accumulation of
20,000 Flight Hours since
the date of issuance of the
original standard airworthi-
ness certificate or the date
of issuance of the original
export certificate of airwor-
thiness, or within 20,000
Flight Hours since last HS-
TA overhaul.
Incorporate SKYTRONICS,
Inc. SB 93004 in accordance
with Accomplishment Instruc-
tions, Paragraph 3.B., Work
Instructions, WORK PACK-
AGE 4.
Group 2, Config-
uration 2 air-
planes
(a) The Horizontal Stabilizer Trim Actuator Ballscrew Assembly 102J033-1 or 102J033-1 (OS) with Oil Lubri-
cator can not be reworked to a Horizontal Stabilizer Trim Actuator Ballscrew Assembly with grease lubri-
cation fitting in accordance with Boeing Service Bulletin 737-27-1046 Revision 1. If you find Stabilizer
Ballscrew Assemblies 102J033-1 or 102J033-1 (OS) installed on the airplane, remove and install 102J033-
3 or 102J033-502 Horizontal Stabilizer Trim Actuator Ballscrew Assembly.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: May 24, 2007
737-27A1278Revision 1: January 07, 2010
37 of 83
BOEING SERVICE BULLETIN 737-27A1278
ALERTALERT

### Page 38

Group 2, Configuration 2:
Table 2 - Inspection, Lubrication, and Overhaul of the Horizontal Stabilizer Trim Actuator; Incorporation
of 737-27-1046 Boeing Service Bulletin, and SKYTRONICS, Inc. 93004 Service Bulletin
NotesRepeat IntervalCompliance Time
(Whichever Occurs First)
ActionCondition
(b) Airplanes with Horizontal Stabilizer Trim Actuator Ballscrew Assemblies with Oil Lubricators can be
changed to Trim Actuators Ballscrew Assemblies with grease lubricator by removing the existing Oil Lu-
bricator Reservoirs and installing a Grease Fitting in accordance with Boeing Service Bulletin 737-27-
1046 Revision 1, dated April 05, 1974.
(c) After you incorporate Boeing Service Bulletin 737-27-1046 Revision 1 (after you install the grease lubri-
cator as given in SB 737-27-1046) the airplane will belong to Group 1 Configuration 1 airplanes. Use the
Detailed Inspection, Lubrication, and Overhaul intervals given in Table 1.
(d) This task accomplishes a detailed inspection of the Horizontal Stabilizer Trim Actuator Ballscrew, Ball
Nut, Ball Nut Tube Retainers and Return Tubes, and also accomplishes a detailed inspection of the
lower and upper Gimbal and the attachment points. The detailed inspection done in accordance with the
service bulletin partially satisfies the intent of the task in accordance with 737-200 MPD Volume 1 Section
4, Item Number 4-27-06. You must accomplish the detailed inspection of the Horizontal Stabilizer Trim
Actuator as given in this service bulletin to establish and stay compliant with this service bulletin.
(e) Accomplishment of this task satisfies the intent of the task in accordance with 737-200 MPD Volume 1
Section 3, Item Number 3-05-01. However you must accomplish this task as given in this service bulletin
to establish and stay compliant with this service bulletin.
F. Approval
This service bulletin was examined by the Federal Aviation Administration (FAA). The changes specified
in this service bulletin comply with the applicable regulations and are FAA approved, as well as European
Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved
airplanes listed in the service bulletin effectivity. This service bulletin and its approval were based on
the airplane in its original Boeing delivery configuration or as modified by other approved Boeing
changes.
If an airplane has a non-Boeing modification or repair that affects a component or system also affected
by this service bulletin, the operator is responsible for obtaining appropriate regulatory agency approval
before incorporating this service bulletin.
G. Manpower
The table below shows an estimate of the task-hours necessary for each airplane to do a detailed
inspection, to lubricate, and to replace the horizontal stabilizer trim actuator. This estimate is for direct
labor only, done by an experienced crew. Adjust the estimate with operator task-hour data if necessary.
The estimate does not include lost time. These are some examples of lost time:
— Time to adjust to the workplace
— Time to schedule the work
— Time to examine the work
— Time to cure the materials
— Time to make the parts
— Time to find the tools.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: May 24, 2007
737-27A1278Revision 1: January 07, 2010
38 of 83
BOEING SERVICE BULLETIN 737-27A1278
ALERTALERT

### Page 39

Elapsed HoursTask-HoursNumber of Per-
sons
Task
1.251.251Open Access
2.04.02Detailed Inspection
1.252.52Lubrication
4.08.02Replace Stabilizer Trim
Actuator (b)
1.251.251Close Access
1.02.02Test
6.7511.0TOTAL FOR EACH AIRPLANE (a)
(a) Total hours does not include actuator replacement.
(b) Hours are for replacement only, additional time required for Stabilizer Trim Actu-
ator overhaul.
H. Weight and Balance Changes
None.
I. Electrical Load Data
Not changed.
J. References
1. Existing Data:
a. Engineering Change Memo PRR 35005-261RS
b. Boeing Service Bulletin 737-27-1046
c. Boeing Service Related Problem (SRP) 737CL-SRP-27-0153
d. Component Maintenance Manual (CMM) 27-41-81, 27-45-11, 27-45-12
e. Federal Aviation Administration (FAA) Notice of Proposed Rule Making 2007-NM-256-AD
f. Overhaul Manual (OHM) 27-45-11
g. Standard Overhaul Practices Manual (SOPM) 20-50-10
h. 737-100/200 Aircraft Maintenance Manual (AMM) 12-22-41, 27-41-121, 27-41-81
i. 737-200 Maintenance Planning Data (MPD) Volume 1Section 1, Volume 1Section 3, Volume
1Section 4
j. 737-300/400/500 Aircraft Maintenance Manual (AMM) 12-22-41, 27-41-81
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: May 24, 2007
737-27A1278Revision 1: January 07, 2010
39 of 83
BOEING SERVICE BULLETIN 737-27A1278
ALERTALERT

### Page 40

k. 737-300/400/500 Maintenance Planning Data (MPD) Volume 1Section 4, Volume 1Section
6
l. LINEAR MOTION, LLC Service Bulletin 7901708
m. SKYTRONICS, Inc. Service Bulletin 93004
n. UMBRA CUSCINETTI, S.p.A. Service Bulletin 07322-27-01
o. LINEAR MOTION, LLC Component Maintenance Manual (CMM) 27-41-01
p. SKYTRONICS, Inc. Component Maintenance Manual (CMM) 27-40-03
q. UMBRA CUSCINETTI, S.p.A. Component Maintenance Manual (CMM) 27-41-01
a. Engineering Change Memo PRR 35005-261RS
b. Boeing Service Bulletin 737-27-1046
c. Boeing Service Related Problem (SRP) 737CL-SRP-27-0153
d. Component Maintenance Manual (CMM) 27-41-81, 27-45-11, 27-45-12
e. Federal Aviation Administration (FAA) Notice of Proposed Rule Making 2007-NM-256-AD
f. Overhaul Manual (OHM) 27-45-11
g. Standard Overhaul Practices Manual (SOPM) 20-50-10
h. 737-100/200 Aircraft Maintenance Manual (AMM) 12-22-41, 27-41-121, 27-41-81
i. 737-200 Maintenance Planning Data (MPD) Volume 1Section 1, Volume 1Section 3, Volume
1Section 4
j. 737-300/400/500 Aircraft Maintenance Manual (AMM) 12-22-41, 27-41-81
k. 737-300/400/500 Maintenance Planning Data (MPD) Volume 1Section 4, Volume 1Section
6
l. LINEAR MOTION, LLC Service Bulletin 7901708
m. SKYTRONICS, Inc. Service Bulletin 93004
n. UMBRA CUSCINETTI, S.p.A. Service Bulletin 07322-27-01
2. Data supplied with this Service Bulletin:
None.
3. Installation Drawings Used in the Preparation of this Service Bulletin:
None.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: May 24, 2007
737-27A1278Revision 1: January 07, 2010
40 of 83
BOEING SERVICE BULLETIN 737-27A1278
ALERTALERT

### Page 41

K. Publications Affected
1. Publications:
Chapter-SectionPublication
737-300/400/500 AMM 12-22-41,
737-300/400/500 AMM 27-41-81
737 Maintenance Manual
CMM 27-45-11737 Component Maintenance Manual
Section 1737-100/200 Maintenance Planning Docu-
ment (MPD)
Section 6737-300/400/500 Maintenance Planning
Document (MPD)
2. Damage Tolerance Based Structural Inspections:
Boeing has evaluated the repairs and/or changes in this service bulletin for effects on Fatigue
Critical Structure (FCS) and for changes to Damage Tolerance Inspections (DTI) required in the
Maintenance Program. This service bulletin does not affect FCS, therefore DTIs are not necessary.
L. Interchangeability and Intermixability of Parts
Refer to Illustration Parts Catalog (IPC) for the Interchangeable parts.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: May 24, 2007
737-27A1278Revision 1: January 07, 2010
41 of 83
BOEING SERVICE BULLETIN 737-27A1278
ALERTALERT

### Page 42

BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: May 24, 2007
737-27A1278Revision 1: January 07, 2010
42 of 83
BOEING SERVICE BULLETIN 737-27A1278
ALERTALERT
BLANK PAGE

### Page 43

2.    MATERIAL INFORMATION
A. Material - Price and Availability
None.
B. Industry Support Information
Boeing warranty remedies are available for 737 airplanes in warranty as of June 14, 2001. For man-hour
reimbursement for airplanes in warranty as of that date, send a warranty claim to Boeing Commercial
Airplanes Group - Warranties. The parts for airplanes in warranty as of that date will be supplied at no
charge. Send a purchase order for the parts to Boeing Spares. Please refer to this service bulletin
number and reference the airplane variable number in your purchase order.
C. Parts Necessary For Each Airplane
1. Kits/Parts:
None.
2. Parts and Materials Supplied by the Operator:
NotesNameQTYPart Number / Specifi-
cation
(a)Kit, 737 HSTA Clamp-7901976
(b)Tube Clamp Kit-102C238-1
Recommended (c)GreaseAs Neces-
sary
BMS 3-33
Alternate to BMS 3-33GreaseAs Neces-
sary
MIL-G-23827
General Purpose OilAs Neces-
sary
MIL-L-7870
(c)Protective Enamel (Clear), Hydraulic
Fluid Resistant
As Neces-
sary
BMS 10-60, Type 2,
Clear or equivalent
(d)Ink or Paste InkAs Neces-
sary
Permanent Marking
Material
(a) You need this kit if you incorporate service bulletin LINEAR MOTION, LLC SB 7901708. Order the
kit from Boeing Spares.
(b) You need this part if you incorporate service bulletin SKYTRONICS, Inc. SB 93004. Order the
number of parts required as given in the Skytronics, Inc. service bulletin from Boeing Spares.
(c) See the Qualified Products List at the end of the Boeing Material Specification (BMS) for supplier
data.
(d) Refer to SOPM 20-50-10 for the list of permanent marking materials.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: May 24, 2007
737-27A1278Revision 1: January 07, 2010
43 of 83
BOEING SERVICE BULLETIN 737-27A1278
ALERTALERT

### Page 44

3. Parts Modified and Reidentified:
None.
4. Parts Removed and Not Replaced:
None.
D. Parts Necessary to Change Spares
None.
E. Special Tooling - Price and Availability
None.
F. Special Tooling Necessary to do this Service Bulletin
No special tools or equipment are necessary to do the change in this service bulletin. But, maintenance
and overhaul tools in the manuals given in Paragraph 1.J., References, can be necessary. Examine
operator tool supply to make sure all necessary tools are available.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: May 24, 2007
737-27A1278Revision 1: January 07, 2010
44 of 83
BOEING SERVICE BULLETIN 737-27A1278
ALERTALERT

### Page 45

3.    ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL INFORMATION
CAUTION: KEEP THE WORK AREA, WIRES AND ELECTRICAL BUNDLES CLEAN OF METAL
PARTICLES OR CONTAMINATION WHEN YOU USE TOOLS. UNWANTED MATERIAL,
METAL PARTICLES OR CONTAMINATION CAUGHT IN WIRE BUNDLES CAN CAUSE
DAMAGE TO THE BUNDLES. DAMAGED WIRE BUNDLES CAN CAUSE SPARKS OR
OTHER ELECTRICAL DAMAGE.
NOTE: 1. Manual titles are referred to by acronyms. Refer to Paragraph 1.J., References, for
definition of the acronyms.
2. Obey all of the warnings and cautions given in the specified manual sections.
3. The work instructions are divided into work packages. Task Hours and Elapsed Hours
for each package are given in Paragraph 1.G., Manpower. You can do each work
package independently.
4. Use the approved fastener and process material substitutions in accordance with
737 SRM, Chapter 51. Alternate fasteners are listed in 737 SRM Chapter 51 and
Boeing Drawing 65-88700.
5. A Detailed Inspection is defined as: An intensive examination of a specific item,
installation, or assembly to detect damage, failure, or irregularity. Available lighting
is normally supplemented with a direct source of good lighting at an intensity deemed
appropriate. Inspection aids such as mirrors, magnifying lenses, etc. may be
necessary. Surface cleaning and elaborate procedures may be required.
6. A General Visual Inspection is defined as: A visual examination of an interior or
exterior area, installation or assembly to detect obvious damage, failure or irregularity.
This level of inspection is made from within touching distance unless otherwise
specified. A mirror may be necessary to ensure visual access to all surfaces in the
inspection area. This level of inspection is made under normal available lighting
conditions such as daylight, hangar lighting, flashlight or drop-light and may require
removal or opening of access panels or doors. Stands, ladders or platforms may be
required to gain proximity to the area being checked.
7. These work instructions refer to procedures included in other Boeing documents.
When the words "refer to" are used and the operator has an accepted alternative
procedure, the accepted alternative procedure can be used. When the words "in
accordance with" are included in the instruction, the procedure in the Boeing document
must be used.
8. Operators will find the term "Stabilizer Trim Actuator" in the Airplane Maintenance
Manual documents. The "Stabilizer Trim Actuator" includes the Ball Nut, Jackscrew,
and Jackscrew Gearbox. The term "Jackscrew" called out in the Airplane Maintenance
Manual documents is referred to as "Ballscrew" in this service bulletin.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: May 24, 2007
737-27A1278Revision 1: January 07, 2010
45 of 83
BOEING SERVICE BULLETIN 737-27A1278
ALERTALERT

### Page 46

B. WORK INSTRUCTIONS
WORK PACKAGE 1 (GROUP 1, GROUP 2 CONFIGURATION 1, and GROUP 3 Airplanes): Detailed
Inspection and Lubrication of the Horizontal Stabilizer Trim Actuator Ballscrew, Ball Nut, and
attachment (Gimbal) fittings
1. Refer to Paragraph 1.E., Compliance, Table 1, for the interval at which the Detailed Inspection
and Lubrication of Stabilizer Trim Actuator Ballscrew, Ball Nut, and attachment fittings (Gimbal
Fittings) need to be accomplished/repeated.
a. Get access to the horizontal Stabilizer Trim Actuator assembly through service access door
3701. Refer to 737-200 MPD Volume 1 Section 1 or 737-300/400/500 MPD Volume 1 Section
4, Access Doors and Panels.
b. Set the STAB TRIM MAIN CUTOUT switch S272, on the control stand, to the CUTOUT
position.
c. Set the AUTOPILOT CRUISE TRIM CUTOUT switch S149, on the control stand, to the
CUTOUT position.
d. Open these circuit breakers shown below and attach the DO-NOT-CLOSE tags:
For Group 1 airplanes:
NotesCircuit BreakerNameLocation (Panel,
Position)
C00207FLIGHT CON-
TROL STAB TRIM
CONT
P6-2, B13
C00840FLIGHT CON-
TROL STAB TRIM
ACTUATOR
P6-2, B11
C00849STABILIZER TRIM
SERVO
P18-0, A1
For Group 2 Configuration 1, and Group 3 airplanes:
NotesCircuit BreakerNameLocation (Panel,
Position)
C00207FLIGHT CON-
TROL STAB TRIM
CONT
P6-2
C00840FLIGHT CON-
TROL STAB TRIM
ACTUATOR
P6-2
C00849STABILIZER TRIM
SERVO
P6-2
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: May 24, 2007
737-27A1278Revision 1: January 07, 2010
46 of 83
BOEING SERVICE BULLETIN 737-27A1278
ALERTALERT

### Page 47

e. Do a detailed inspection of the Horizontal Stabilizer Trim Actuator:
For Group 1 Configuration 1, Group 2 Configuration 1, and Group 3 Airplanes in accordance
with FIGURE 1.
For Group 1 Configuration 2 airplanes in accordance with FIGURE 2.
(1) Do a detailed inspection of all attachment points of the Lower and Upper Gimbal for cracks
and other damage. Inspect the areas around the holes and bushing. Make sure that the
Stabilizer Trim Actuator is correctly attached to the airplane structure. If any damage is
found, repair or replace the damaged parts. Refer to 737-100/200 AMM 27-41-81 or
737-300/400/500 AMM 27-41-81 and CMM 27-45-12 as an accepted procedure.
(2) Do a general visual inspection of the area under, on, and around the Stabilizer Trim
Actuator to see if grease is escaping from Ball Nut. Large amounts of grease present
around the Stabilizer Trim Actuator indicate that a faulty seal or lifted return tube may be
present on the Ball Nut.
If a large amount of grease is present due to a faulty seal or lifted/leaking return tube,
repair/replace the Stabilizer Trim Actuator in accordance with FIGURE 7 for Group 1
Configuration 1, Group 2 Configuration 1, and Group 3 Airplanes and in accordance with
FIGURE 8 for Group 1 Configuration 2 airplanes.
(3) Do a detailed inspection of the grease on and around the Ballscrew and Ball Nut for
existence of metallic particles, other solid particles, and corrosion products in the grease.
If metallic particles, or other solid particles, or corrosion products are found in the grease,
Repair/Replace the Stabilizer Trim Actuator:
For Group 1 Configuration 1, Group 2 Configuration 1, and Group 3 Airplanes in
accordance with FIGURE 7.
For Group 1 Configuration 2 Airplanes in accordance with FIGURE 8.
NOTE: If visible metallic particles are observed in the grease there may be some damage
in the Ballscrew/Ball Nut assembly. Normal wear of the Ballscrew actuator can
happen, but this will not release visible metallic particles in the grease.
(4) Check if any of the Ball Nut bearings are found in the vicinity of the Ball Nut, on the
Ballscrew, or directly below the Stabilizer Trim Actuator. If Ball Nut ball bearings are found
Repair/Replace the Horizontal Stabilizer Trim Actuator:
For Group 1 Configuration 1, Group 2 Configuration 1, and Group 3 airplanes in
accordance with FIGURE 7.
For Group 1 Configuration 2 airplanes in accordance with FIGURE 8.
NOTE: The Ball Nut ball bearings used inside the 737 Ball Nut are approximately 0.218
inch (5.6mm) in diameter.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: May 24, 2007
737-27A1278Revision 1: January 07, 2010
47 of 83
BOEING SERVICE BULLETIN 737-27A1278
ALERTALERT

### Page 48

(5) Remove any old grease and dirt from the Ballscrew threads by wiping them with a clean,
dry, non-abrasive cloth.
(6) Do a detailed inspection of the Ball Nut Tube Retainers for deformation and corrosion or
lifted Return Tubes. If the Ball Nut Tube Retainers have deformation or corrosion or the
Return Tubes are lifted, Repair/Replace the stabilizer Trim Actuator:
For Group 1 Configuration 1, Group 2 Configuration 1, and Group 3 airplanes in
accordance with FIGURE 7.
For Group 1 Configuration 2 airplanes in accordance with FIGURE 8.
NOTE: Operators will find in the applicable Component Maintenance Manuals (CMM)
for Ballscrew Assembly the following terms: Ball Nut "Tube Retainers" (for
UMBRA CUSCINETTI, S.p.A. Ballscrew Assemblies), or BallNut "Return Tube
Covers" (LINEAR MOTION, LLC), or Ball Nut "Return Tube Clamps"
(SKYTRONICS, Inc.). The Term "Ball Nut Tube Retainers" will be used
throughout the Accomplishment Instructions.
(7) Do a detailed inspection of the Ballscrew for the following problems:
(a) Inspect the Ballscrew threads for cross-threading, distortion, or stripping. If you find
any of these conditions Repair/Replace the Stabilizer Trim Actuator in accordance
with:
For Group 1 Configuration 1, Group 2 Configuration 1, and Group 3 airplanes in
accordance with FIGURE 7.
For Group 1 Configuration 2 airplanes in accordance with FIGURE 8
(b) Check the Ballscrew for metallic particles, pitting, gouging, corrosion, spalling,
brinelling, cracks, and worn areas in the Ballscrew threads. If metallic particles, pitting,
gouging, corrosion, spalling, brinelling, cracks, or worn areas in the Ballscrew threads
is observed, repair/replace (as necessary) the Stabilizer Trim actuator:
For Group 1 Configuration 1, Group 2 Configuration 1, and Group 3 airplanes in
accordance with FIGURE 7
For Group 1 Configuration 2 airplanes in accordance with FIGURE 8
(c) Check for obvious differences in thread shape between thread grooves in the lower,
middle, and upper portions of the Ballscrew. If obvious differences in thread shape
between thread grooves in the lower, middle, and upper portions of the Ballscrew
are observed repair/replace (as necessary) the Stabilizer Trim Actuator:
For Group 1 Configuration 1, Group 2 Configuration 1, and Group 3 airplanes in
accordance with FIGURE 7.
For Group 1 Configuration 2 airplanes in accordance with FIGURE 8.
f. Remove the DO-NOT-CLOSE tags and close the circuit breakers shown below:
For Group 1 airplanes:
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: May 24, 2007
737-27A1278Revision 1: January 07, 2010
48 of 83
BOEING SERVICE BULLETIN 737-27A1278
ALERTALERT

### Page 49

NotesCircuit BreakerNameLocation (Panel,
Position)
C00207FLIGHT CON-
TROL STAB TRIM
CONT
P6-2, B13
C00840FLIGHT CON-
TROL STAB TRIM
ACTUATOR
P6-2, B11
C00849STABILIZER TRIM
SERVO
P18-0, A1
For Group 2 Configuration 1, and Group 3 airplanes:
NotesCircuit BreakerNameLocation (Panel,
Position)
C00207FLIGHT CON-
TROL STAB TRIM
CONT
P6-2
C00840FLIGHT CON-
TROL STAB TRIM
ACTUATOR
P6-2
C00849STABILIZER TRIM
SERVO
P6-2
g. Set the STAB TRIM MAIN CUTOUT switch, S272, on the control stand, to the NORMAL
position.
h. Push and hold the Stabilizer Trim Control switches on the Captain's Control Wheel (NOSE
UP or NOSE DOWN) to move the ballscrew to another location other than the current setting.
i. Make sure the operation is smooth and there is no unusual noise.
j. Set the STAB TRIM MAIN CUTOUT switch, S272 on the control stand, to the CUTOUT
position.
k. Make sure that the AUTOPILOT CRUISE TRIM CUTOUT switch S149, on the control stand,
is SET to the CUTOUT position.
l. Open this circuit breakers shown below and attach the DO-NOT-CLOSE tags:
For Group 1 airplanes:
NotesCircuit BreakerNameLocation (Panel,
Position)
C00207FLIGHT CON-
TROL STAB TRIM
CONT
P6-2, B13
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: May 24, 2007
737-27A1278Revision 1: January 07, 2010
49 of 83
BOEING SERVICE BULLETIN 737-27A1278
ALERTALERT

### Page 50

NotesCircuit BreakerNameLocation (Panel,
Position)
C00840FLIGHT CON-
TROL STAB TRIM
ACTUATOR
P6-2, B11
C00849STABILIZER TRIM
SERVO
P18-0, A1
For Group 2 Configuration 1, and Group 3 airplanes:
NotesCircuit BreakerNameLocation (Panel,
Position)
C00207FLIGHT CON-
TROL STAB TRIM
CONT
P6-2
C00840FLIGHT CON-
TROL STAB TRIM
ACTUATOR
P6-2
C00849STABILIZER TRIM
SERVO
P6-2
m. Do a detailed inspection of the grease on the newly exposed area of the Ballscrew for metallic
particles, other solid particles, and corrosion products in the grease. If metallic particles, or
other solid particles, or corrosion products are found in the grease Repair/Replace the Stabilizer
Trim Actuator:
For Group 1 Configuration 1, Group 2 Configuration 1, and Group 3 airplanes in accordance
with FIGURE 7.
For Group 1 Configuration 2 airplanes in accordance with FIGURE 8.
NOTE: If visible metallic particles are observed in the grease there may be some damage
in the Ballscrew/Ball Nut assembly. Normal wear of the Ballscrew actuator can
happen, but this will not release visible metallic particles in the grease.
n. Remove any grease from the newly exposed portion of the Ballscrew threads by wiping them
with a clean, dry, non abrasive cloth.
o. Do a detailed inspection of the newly exposed Ballscrew for the following problems:
(1) Inspect the Ballscrew threads for cross-threading, distortion, or stripping. If you find any
of these conditions Repair/Replace the Stabilizer Trim actuator in accordance with:
For Group 1 Configuration 1, Group 2 Configuration 1, and Group 3 airplanes in
accordance with FIGURE 7.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: May 24, 2007
737-27A1278Revision 1: January 07, 2010
50 of 83
BOEING SERVICE BULLETIN 737-27A1278
ALERTALERT

### Page 51

For Group 1 Configuration 2 airplanes in accordance with FIGURE 8.
(2) Check the Ballscrew for metallic particles, pitting, gouging, corrosion, spalling, brinelling,
cracks, and worn areas in the Ballscrew threads. If metallic particles, pitting, gouging,
corrosion, spalling, brinelling, cracks, or worn areas in the Ballscrew threads is observed,
repair/replace (as necessary) the Stabilizer Trim Actuator:
For Group 1 Configuration 1, Group 2 Configuration 1, and Group 3 in accordance with
FIGURE 7.
For Group 1 Configuration 2 airplane in accordance with FIGURE 8.
(3) Check for obvious differences in the thread shape between thread grooves in the lower,
middle, and upper portions of the Ballscrew. If obvious differences in thread shape between
thread grooves in the lower, middle, and upper portions of the Ballscrew are observed,
repair/replace (as necessary) the Stabilizer Trim Actuator:
For Group 1 Configuration 1, Group 2 Configuration 1, and Group 3 airplanes in
accordance with FIGURE 7.
For Group 1 Configuration 2 airplanes in accordance with FIGURE 8.
p. Apply grease (Lubricate) the Ballscrew and Ball Nut:
For Group 1 Configuration 1, Group 2 Configuration 1, and Group 3 airplanes in accordance
with FIGURE 4.
For Group 1 Configuration 2 airplanes in accordance with FIGURE 5.
Apply the grease slowly until clean, new, fresh grease exits through the grease vent. If clean,
new, fresh grease fails to exit the grease vent OR the upper seal, repair/replace the Stabilizer
Trim Actuator:
For Group 1 Configuration 1, Group 2 Configuration 1, and Group 3 airplanes in accordance
with FIGURE 7.
For Group 1 Configuration 2 airplanes in accordance with FIGURE 8.
(1) Inspect if grease exits the Ball Nut through Upper Seal, Lower Seal and around the Tube
Retainer areas:
(a) Clean, new fresh grease, that exits from the upper seal is also an acceptable indication
of proper lubrication of the Ball Nut.
(b) Small amounts of grease may exit the lower seal and is considered acceptable as
long as the general visual inspection of the under, on, and around the Stabilizer Trim
Actuator given in WORK PACKAGE 1 step 1.e.2 was found satisfactory.
(c) Small amount of grease may exit the ball nut through the Tube Retainer areas (from
the Return Tubes). If small amount of grease is observed around the Tube Retainer
do a detailed inspection of the Ball Nut Tube Retainers for deformation and corrosion
or lifted Return Tubes. If the Ball Nut Tube Retainers have deformation or corrosion
Repair/Replace (as necessary) the Stabilizer Trim Actuator:
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: May 24, 2007
737-27A1278Revision 1: January 07, 2010
51 of 83
BOEING SERVICE BULLETIN 737-27A1278
ALERTALERT

### Page 52

For Group 1 Configuration 1, Group 2 Configuration 1, and Group 3 airplanes in
accordance with FIGURE 7.
For Group 1 Configuration 2 airplanes in accordance with FIGURE 8.
If no damage of the Tube Retainers is found, the condition is acceptable.
If large amount of grease exits through the Tube Retainer areas, the Return Tubes
may be lifted and the Stabilizer Trim Actuator must be repaired or replaced:
For Group 1 Configuration 1, Group 2 Configuration 1, and Group 3 airplanes in
accordance with FIGURE 7.
For Group 1 Configuration 2 airplanes in accordance with FIGURE 8.
(2) Inspect the grease that exits the Ball Nut for indication of metallic particles, discolored
water, rust, or other solid particles. If any of these conditions exist Repair/Replace the
Stabilizer Trim Actuator:
For Group 1 Configuration 1, Group 2 Configuration 1, and Group 3 airplanes in
accordance with FIGURE 7.
For Group 1 Configuration 2 airplanes in accordance with FIGURE 8.
NOTE: If visible metallic particles are observed in the grease there may be some damage
in the Ballscrew/Ball Nut assembly. Normal wear of the Ballscrew Actuator can
happen but this will not release visible metallic particles in the grease.
2. Remove the DO-NOT-CLOSE tags and close the circuit breakers shown below:
For Group 1 airplanes:
NotesCircuit BreakerNameLocation (Panel,
Position)
C00207FLIGHT CON-
TROL STAB TRIM
CONT
P6-2, B13
C00840FLIGHT CON-
TROL STAB TRIM
ACTUATOR
P6-2, B11
C00849STABILIZER TRIM
SERVO
P18-0, A1
For Group 2 Configuration 1, and Group 3 airplanes:
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: May 24, 2007
737-27A1278Revision 1: January 07, 2010
52 of 83
BOEING SERVICE BULLETIN 737-27A1278
ALERTALERT

### Page 53

NotesCircuit BreakerNameLocation (Panel,
Position)
C00207FLIGHT CON-
TROL STAB TRIM
CONT
P6-2
C00840FLIGHT CON-
TROL STAB TRIM
ACTUATOR
P6-2
C00849STABILIZER TRIM
SERVO
P6-2
3. Close the service access door 3701. Refer to 737-200 MPD Volume 1 Section 1 or 737-300/400/500
MPD Volume 1 Section 4, Access Doors and Panels.
4. Put the airplane back to a serviceable condition.
NOTE: Make sure that you set the STAB TRIM MAIN CUTOUT to the serviceable position.
WORK PACKAGE 2 (GROUP 2 CONFIGURATION 2 Airplanes): Detailed Inspection and Lubrication
of the Horizontal Stabilizer Trim Actuator Ballscrew, Ball Nut, and attachment (Gimbal) fittings
1. Refer to Section 1.E., Compliance, Table 2, for the interval at which the Detailed Inspection and
Lubrication of Stabilizer Trim Actuator Ballscrew, Ball Nut, and attachment fittings (Gimbal Fittings)
need to be accomplished/repeated.
a. Get access to the Horizontal Stabilizer Trim Actuator assembly through service access door
3701. Refer to 737-200 MPD Volume 1 Section 1, Access Doors and Panels.
b. Set the STAB TRIM MAIN CUTOUT switch S272, on the control stand, to the CUTOUT
position.
c. Set the AUTOPILOT CRUISE TRIM CUTOUT switch S149, on the control stand, to the
CUTOUT position.
d. Open this circuit breakers shown below and attach the DO-NOT-CLOSE tags:
NotesCircuit BreakerNameLocation (Panel,
Position)
C00207FLIGHT CON-
TROL STAB TRIM
CONT
P6-2
C00840FLIGHT CON-
TROL STAB TRIM
ACTUATOR
P6-2
C00849STABILIZER TRIM
SERVO
P6-2
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: May 24, 2007
737-27A1278Revision 1: January 07, 2010
53 of 83
BOEING SERVICE BULLETIN 737-27A1278
ALERTALERT

### Page 54

e. Do a detailed inspection of the Horizontal Stabilizer Trim Actuator in accordance with FIGURE
3:
(1) Do a detailed inspection of all attachment points of the Lower and Upper Gimbal for cracks
and other damage. Inspect the area around the holes and bushing. Make sure that the
Stabilizer Trim Actuator is correctly attached to the airplane structure. If any damage is
found, repair or replace the damaged part. Refer to 737-100/200 AMM 27-41-81 and
CMM 27-45-12 as an accepted procedure .
(2) Do a detailed inspection of the oil on and around the Ballscrew and Ball Nut for existence
of metallic particles, other solid particles, and corrosion products in the oil. If metallic
particles, or other solid particles, or corrosion products are found in the oil, Repair/Replace
the Stabilizer Trim Actuator in accordance with FIGURE 9.
NOTE: If visible metallic particles are observed in the oil there may be some damage
in the Ballscrew/Ball Nut assembly. Normal wear of the Ballscrew actuator can
happen, but this will not release visible metallic particles in the oil.
(3) Check if any of the Ball Nut bearings are found in the vicinity of the Ball Nut, on the
Ballscrew, or directly below the Stabilizer Trim Actuator. If Ball Nut bearings are found
Repair/Replace the Horizontal Stabilizer Trim Actuator in accordance with FIGURE 9.
NOTE: The Ball Nut bearings used inside the 737 Ball Nut are approximately 0.218 inch
(5.6 mm) in diameter.
(4) Remove any old oil and dirt from the Ballscrew threads by wiping them with a clean, dry,
non-abrasive cloth.
(5) Do a detailed inspection of the Ball Nut Tube Retainers for deformation and corrosion or
lifted return tubes. If the Ball Nut Tube Retainers have deformation or corrosion or the
Return Tubes are lifted, Repair/Replace the Stabilizer Trim Actuator in accordance with
FIGURE 9.
(6) Do a detailed inspection of the Ballscrew for the following problems in accordance with
FIGURE 3.
(a) Inspect the Ballscrew threads for cross-threading, distortion, or stripping.
(b) Check the Ballscrew for metallic particles, pitting, gouging, corrosion, spalling,
brinelling, cracks and worn areas in the Ballscrew threads. If metallic particles, pitting,
gouging, corrosion, spalling, brinelling, cracks, or worn areas in the Ballscrew threads
is observed, repair/replace (as necessary) the Stabilizer Trim Actuator in accordance
with FIGURE 9.
(c) Check for obvious differences in thread shape between thread grooves in the lower,
middle, and upper portions of the Ballscrew. If obvious differences in thread shape
between thread grooves in the lower, middle, and upper portions of the Ballscrew is
observed, repair/replace (as necessary) the Stabilizer Trim Actuator in accordance
with FIGURE 9.
f. Remove the DO-NOT-CLOSE tags and close the circuit breakers shown below:
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: May 24, 2007
737-27A1278Revision 1: January 07, 2010
54 of 83
BOEING SERVICE BULLETIN 737-27A1278
ALERTALERT

### Page 55

NotesCircuit BreakerNameLocation (Panel,
Position)
C00207FLIGHT CON-
TROL STAB TRIM
CONT
P6-2
C00840FLIGHT CON-
TROL STAB TRIM
ACTUATOR
P6-2
C00849STABILIZER TRIM
SERVO
P6-2
g. Set the STAB TRIM MAIN CUTOUT switch S272, on the control stand, to the NORMAL
position.
h. Push and hold the Stabilizer Trim Control switches on the Captain's Control Wheel (NOSE
UP or NOSE DOWN) to move the ballscrew to another location other than the current setting.
i. Make sure the operation is smooth and there is no unusual noise.
j. Set the STAB TRIM MAIN CUTOUT switch S272, on the control stand, to the CUTOUT
position.
k. Make sure that the AUTOPILOT CRUISE TRIM CUTOUT switch S149, on the control stand,
is SET to the CUTOUT position.
l. Open these circuit breakers shown below and attach the DO-NOT-CLOSE tags:
NotesCircuit BreakerNameLocation (Panel,
Position)
C00207FLIGHT CON-
TROL STAB TRIM
CONT
P6-2
C00840FLIGHT CON-
TROL STAB TRIM
ACTUATOR
P6-2
C00849STABILIZER TRIM
SERVO
P6-2
m. Do a detailed inspection of the oil on the newly exposed area of the Ballscrew for metallic
particles, other solid particles, and corrosion products in the oil. If metallic particles, or other
solid particles, or corrosion products are found in the oil Repair/Replace the Stabilizer Trim
Actuator in accordance with FIGURE 9.
NOTE: If visible metallic particles are observed in the oil there may be some damage in the
Ballscrew/Ball Nut assembly. Normal wear of the Ballscrew actuator can happen,
but this will not release visible metallic particles in the oil.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: May 24, 2007
737-27A1278Revision 1: January 07, 2010
55 of 83
BOEING SERVICE BULLETIN 737-27A1278
ALERTALERT

### Page 56

n. Remove any oil from the newly exposed portion of the Ballscrew threads by wiping them with
a clean, dry, non abrasive cloth.
o. Do a detailed inspection of the newly exposed area of the Ballscrew for the following problems
in accordance with FIGURE 3.
(1) Inspect the Ballscrew threads for cross-threading, distortion, or stripping.
(2) Check the Ballscrew for metallic particles, pitting, gouging, corrosion, spalling, brinelling,
cracks, and worn areas in the Ballscrew threads. If metallic particles, pitting, gouging,
corrosion, spalling, brinelling, cracks, or worn areas in the Ballscrew threads is observed,
remove, inspect, repair/replace (as necessary) the Stabilizer Trim Actuator in accordance
with FIGURE 9.
(3) Check for obvious differences in the thread shape between thread grooves in the lower
middle, and upper portions of the Ballscrew. If obvious differences in thread shape between
thread grooves in the lower, middle, and upper portion of the Ballscrew are observed,
remove, inspect, repair/replace (as necessary) the Stabilizer Trim Actuator in accordance
with FIGURE 9.
p. Apply grease (Lubricate) and fill oil reserver in accordance with FIGURE 6.
2. Remove the DO-NOT-CLOSE tags and close the circuit breakers shown below:
NotesCircuit BreakerNameLocation (Panel,
Position)
C00207FLIGHT CON-
TROL STAB TRIM
CONT
P6-2
C00840FLIGHT CON-
TROL STAB TRIM
ACTUATOR
P6-2
C00849STABILIZER TRIM
SERVO
P6-2
3. Close the service access door 3701. Refer to 737-200 MPD Volume 1 Section 1, Access Doors
and Panels.
4. Put the airplane back to a serviceable condition.
NOTE: Make sure that you set the STAB TRIM MAIN CUTOUT to the serviceable position.
WORK PACKAGE 3 (GROUP 2, CONFIGURATION 2 AIRPLANES): Incorporate Boeing Service
Bulletin 737-27-1046, Revision 1, dated April 05, 1974 (If service bulletin is not already
incorporated)
1. For airplane with Horizontal Stabilizer Trim Actuator Ballscrew Assemblies with Oil Lubricators,
remove the existing Oil Lubricator Reservoirs and install a Grease Fitting in accordance with Boeing
Service Bulletin 737-27-1046 Revision 1, dated April 05, 1974.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: May 24, 2007
737-27A1278Revision 1: January 07, 2010
56 of 83
BOEING SERVICE BULLETIN 737-27A1278
ALERTALERT

### Page 57

a. If you find the Stabilizer Ballscrew Assy 102J033-1 or 102J033-1 (OS) installed on the airplane,
remove and install Stabilizer Ballscrew Assy 102J033-3 or 102J033-502. If you install a
Stabilizer Ballscrew Assy 102J033-3 make sure that you incorporate Boeing Service Bulletin
737-27-1046 Revision 1, dated April 05, 1974 (if not already incorporated), before you install
this ballscrew assembly on the airplane.
NOTE: The Horizontal Stabilizer Trim Actuator Ballscrew Assembly 102J033-1 or 102J033-1
(OS) with Oil Lubricator can not be reworked to a Horizontal Stabilizer Trim Actuator
Ballscrew Assembly with grease lubrication fitting as given in Service Bulletin
737-27-1046.
NOTE: The Horizontal Stabilizer Trim Actuators with Oil Lubricators reworked to Horizontal
Stabilizer Trim Actuator with grease lubrication fittings in accordance with Service
Bulletin 737-27-1046 Revision 1, have to incorporate the SKYTRONICS, Inc. SB
93004 Service Bulletin, Dated September 01, 2005 in accordance with Work Package
4.
WORK PACKAGE 4 (ALL AIRPLANES): Rework the Stabilizer Trim Actuator Ballscrew assembly
1. For airplane with UMBRA CUSCINETTI Ballscrew Assemblies, install new Ball Nut Tube Retainers
in accordance with UMBRA CUSCINETTI, S.p.A. SB 07322-27-01 Service Bulletin, Rev 00, Dated
December 21, 2004.
a. After you incorporate UMBRA CUSCINETTI, S.p.A. SB 07322-27-01 Service Bulletin, hand
letter with a permanent ink or paste ink, in the area adjacent to the HSTA name plate (gear
box area) the following:
"UMBRA CUSCINETTI, S.p.A. SB 07322-27-01 IS INCORPORATED ON THIS HSTA IN
ACCORDANCE WITH SB 737-27A1278, WORK PACKAGE 4"
Apply BMS 10-60, Type 2, Clear, over the marking, to protect the marking from hydraulic fluid.
Refer to SOPM 20-50-10 as an accepted procedure for the marking process and marking
materials.
2. For airplane with LINEAR MOTION Ballscrew Assemblies, install new Ball Deflectors and Ball
Return Guide Clamps in accordance with LINEAR MOTION, LLC SB 7901708 Service Bulletin,
Dated July 26, 2005.
a. After you incorporate LINEAR MOTION, LLC SB 7901708 Service Bulletin, hand letter with
a permanent ink or paste ink, in the area adjacent to the HSTA name plate (gear box area)
the following:
"LINEAR MOTION, LLC SB 7901708 IS INCORPORATED ON THIS HSTA IN ACCORDANCE
WITH SB 737-27A1278, WORK PACKAGE 4"
Apply BMS 10-60, Type 2, Clear, over the marking, to protect the marking from hydraulic fluid.
Refer to SOPM 20-50-10 as an accepted procedure for the marking process and marking
materials.
3. For airplane with SKYTRONICS Ballscrew Assemblies, install the new Return Tube Clamps in
accordance with SKYTRONICS, Inc. SB 93004 Service Bulletin, Dated September 01, 2005.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: May 24, 2007
737-27A1278Revision 1: January 07, 2010
57 of 83
BOEING SERVICE BULLETIN 737-27A1278
ALERTALERT

### Page 58

a. If you find the Stabilizer Ballscrew Assy 102J033-1 or 102J033-1 (OS) installed on the airplane
remove and install Stabilizer Ballscrew Assy 102J033-502 or equivalent. If you install a
Stabilizer Ballscrew Assy 102J033-3 make sure to incorporate SB 737-27-1046 before you
install the Stabilizer Ballscrew Assy on the airplane.
b. After you incorporate SKYTRONICS, Inc. SB 93004 Service Bulletin, hand letter with a
permanent ink or paste ink, in the area adjacent to the HSTA name plate (gear box area) the
following:
"SKYTRONICS, Inc. SB 93004 IS INCORPORATED ON THIS HSTA IN ACCORDANCE
WITH SB 737-27A1278, WORK PACKAGE 4"
Apply BMS 10-60, Type 2, Clear, over the marking, to protect the marking from hydraulic fluid.
Refer to SOPM 20-50-10 as an accepted procedure for the marking process and marking
materials.
WORK PACKAGE 5 (ALL AIRPLANES): Remove the Stabilizer Trim Actuator for Repair/Overhaul
1. Remove and Repair/Overhaul the Horizontal Stabilizer Trim Actuator:
For Group 1 Configuration 1, Group 2 Configuration 1, and Group 3 airplane in accordance with
FIGURE 7.
For Group 1 Configuration 2 airplane in accordance with FIGURE 8.
For Group 2 Configuration 2 airplane in accordance with FIGURE 9.
Repeat the Overhaul as given in Paragraph 1.E., Compliance, Table 1 or Table 2, as applicable.
NOTE: Refer to 737-100/200 AMM 27-41-81 or 737-300/400/500 AMM 27-41-81 for instructions
to remove the Horizontal Stabilizer Trim Actuator. Refer to the applicable Component
Maintenance Manual: UMBRA CUSCINETTI, S.p.A. CMM 27-41-01, or LINEAR MOTION
LLC CMM 27-41-01, or SKYTRONICS Inc CMM 27-40-03 and CMM 27-45-11 for repairs
of the Horizontal Stabilizer Trim Actuator components.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: May 24, 2007
737-27A1278Revision 1: January 07, 2010
58 of 83
BOEING SERVICE BULLETIN 737-27A1278
ALERTALERT

### Page 59 (OCR)

BOEING SERVICE BULLETIN 737-27A1278
ALERT  ALERT
This Figure applies only to: Group 1-2, Configuration 1; Group 3.
BALLSCREW
FITTING
SEE
/ BALL NUT
• SEE A
SERVICE ACCESS
DOOR 3701L
8) BALLSCREW
AUTOPILOT
ELECTRIC  ELECTRIC
MOTOR  ACTUATOR
LOWER
GIMBAL
2 LOCATIONS
FWD *
AFT CABLE
DRUM  D62326
FIGURE 1: HORIZONTAL STABILIZER TRIM ACTUATOR - DETAILED INSPECTION OF THE BALLSCREW,
BALL NUT, AND THE ATTACHMENT FITTINGS- (GROUP 1 CONFIGURATION 1, GROUP 2 CONFIGURATION
1, AND GROUP 3 AIRPLANES)
(SHEET 1 OF 4)
Original Issue: May 24, 2007
Revision 1 January 07, 2010  737-27A1278
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.  59 of 83

### Page 60 (OCR)

BOEING SERVICE BULLETIN 737-27A1278
ALERT  ALERT
BALLSCREW
23431300
BALL NUT
469
- UPPER GIMBAL
BALLSCREW  FITTING
FITTING  (2 LOCATIONS)
460
BALL NUT
FWDE
FIGURE 1: HORIZONTAL STABILIZER TRIM ACTUATOR - DETAILED INSPECTION OF THE BALLSCREW,
BALL NUT, AND THE ATTACHMENT FITTINGS- (GROUP 1 CONFIGURATION 1, GROUP 2 CONFIGURATION
1, AND GROUP 3 AIRPLANES)
(SHEET 2 OF 4)
Original Issue: May 24, 2007
Revision 1 January 07, 2010  BOEING PROPRIETARY -  737-27A1278
Copyright © Unpublished Work - See page 1 for details.  60 of 83

The text continues at https://openairdocs.org/service-documents/boeing/737-27a1278/file/b8153b5e3b7c.md?from=61

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
