# Boeing Alert Service Bulletin 737-27A1330: No revision named, from page 13

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2025-0469, the docket of a proposed AD (Federal Register 2025-06274). Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Alert Service Bulletin 737-27A1330](https://openairdocs.org/service-documents/boeing/737-27a1330.md)
- Title as filed: RB737-27A1330 R0
- Pages: 46
- PDF: https://openairdocs.org/files/sha256/52/fb/52fbfb3fda4e4c347b5ca91bc4fcc4d94903425cdc50ac19a0270dda1befac41
- Page: https://openairdocs.org/service-documents/boeing/737-27a1330/file/52fbfb3fda4e

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 13

GroupVariable Number
1YW701 - YW715
1YW726 - YW731
1YW766 - YW775
1YW801 - YW803
1YW811 - YW813
GroupVariable Number
1YW821
1YW831
1YW881
1YW891 - YW893
1YW906 - YW910
GroupVariable Number
1YW916 - YW918
1YW921 - YW925
1YW971 - YW976
--
--
B. Spares Affected
Examine your spares supply for the parts or components identified below. If any parts or components
are found, refer to Accomplishment Instructions for the recommended action.
NamePart Number
HORIZONTAL STABILIZER TRIM ACTUATOR251A4510-( ) (a)(b)
(a) Any dash number is an acceptable HSTA part number.
(b) Any spare overhauled HSTA prior to 737 AMM 27-41-81 dated January 6, 2024.
2. CONCURRENT REQUIREMENTS
None.
3. COMPLIANCE
The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to
Requirements Bulletin 737-27A1330 RB. The Airworthiness Directive will make the compliance tasks and
times given in Requirements Bulletin 737-27A1330 RB mandatory.
Accomplish the required action(s), based on the applicable condition(s) in Table(s) 1-3, in accordance with
the Accomplishment Instructions.
When more than one OPTION is given for a CONDITION, do only one of the OPTION numbers. When
more than one ACTION is given for a CONDITION or an OPTION, do all of the ACTION numbers for that
CONDITION or OPTION.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 07, 2024
737-27A1330 RB
13 of 46
REQUIREMENTS BULLETIN 737-27A1330
ALERTALERT

### Page 14

Table 1: Horizontal Stabilizer Trim Actuator - Lower Gimbal Assembly Fastener Inspection and Torque
Check
Repeat
Interval
(Not to Ex-
ceed)
Boeing
Recommended
Compliance Time
ActionCondition
-Within 20 months after
the Original Issue date
of Requirements Bul-
letin 737-27A1330 RB.
Do a maintenance records check to
see if the overhauled Horizontal
Stabilizer Trim Actuator (HSTA) was
inspected and corrective actions
were accomplished using the appli-
cable Boeing Provided Inspection
Requirements and Corrective Ac-
tions identified in APPENDIX A.
Airplanes with overhauled HSTA
prior to 737 AMM 27-41-81 dated
January 6, 2024.
--No further action is required.CONDITION 1: MAINTENANCE
RECORDS SHOW OVERHAULED
HSTA WAS INSPECTED AND
CORRECTIVE ACTIONS WERE
ACCOMPLISHED
-Within 20 months after
the Original Issue date
of Requirements Bul-
letin 737-27A1330 RB.
Do a General Visual Inspection of
the 12 fastener locations on the
lower gimbal assembly to see if all
attachment hardware is installed.(a)
CONDITION 2: MAINTENANCE
RECORDS SHOW OVERHAULED
HSTA WAS NOT INSPECTED OR
NO MAINTENANCE RECORDS
FOUND
-At the time specified in
Table 3.
Do the actions specified in Table 3.CONDITION 2.1: ATTACHMENT
HARDWARE FOUND MISSING AT
ALL 3 FASTENER LOCATIONS IN
ANY CORNER
-Before further flight.Do a General Visual Inspection of
the lower gimbal assembly where
the attachment hardware is missing
for any crack and any corrosion.
CONDITION 2.2: ATTACHMENT
HARDWARE FOUND MISSING AT
LESS THAN 3 FASTENER LOCA-
TIONS IN ANY CORNER AND NO
CORNER WITH ATTACHMENT
HARDWARE MISSING AT ALL 3
FASTENER LOCATIONS
-Before further flight.CONDITION 2.2.1 (ACTION 1):CONDITION 2.2.1: NO LOWER
GIMBAL ASSEMBLY CRACK AND
NO CORROSION FOUND
Install new attachment hardware at
each missing location and tighten to
specified torque value. (b)
-Before further flight.CONDITION 2.2.1 (ACTION 2):
Measure the torque value of the
HSTA lower gimbal nut at each of
the 12 fastener locations where the
nut was not missing and determine
if it is under-torqued.
--No further action is required.CONDITION 2.2.1.1: NO UNDER-
TORQUED NUT FOUND
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 07, 2024
737-27A1330 RB
14 of 46
REQUIREMENTS BULLETIN 737-27A1330
ALERTALERT

### Page 15

Table 1: Horizontal Stabilizer Trim Actuator - Lower Gimbal Assembly Fastener Inspection and Torque
Check
Repeat
Interval
(Not to Ex-
ceed)
Boeing
Recommended
Compliance Time
ActionCondition
-At the time specified in
Table 2.
Do the actions specified in Table 2.CONDITION 2.2.1.2: ANY UNDER-
TORQUED NUT FOUND
-At the time specified in
Table 3.
Do the actions specified in Table 3.CONDITION 2.2.2: ANY LOWER
GIMBAL ASSEMBLY CRACK OR
ANY CORROSION FOUND
-Before further flight.Measure the torque value of the
HSTA lower gimbal nut at each of
the 12 fastener locations and deter-
mine if it is under-torqued.
CONDITION 2.3: NO ATTACH-
MENT HARDWARE FOUND MISS-
ING AT THE 12 FASTENER LOCA-
TIONS
--No further action is required.CONDITION 2.3.1: NO UNDER-
TORQUED NUT FOUND
-At the time specified in
Table 2.
Do the actions specified in Table 2.CONDITION 2.3.2: ANY UNDER-
TORQUED NUT FOUND
(a) Attachment hardware is defined as any bolt, nut or washer.
(b) If new nut does not generate 5 in-lb of torque while installing, the fastener must be replaced. Remove the
HSTA as necessary for fastener replacement.
Table 2: On-condition corrective actions for airplanes with any under-torqued nut found.
Repeat
Interval
(Not to Ex-
ceed)
Boeing
Recommended
Compliance Time
ActionCondition
-Before further flight.ACTION 1:Airplanes in Table 1, CONDITION
2.2.1.2 or CONDITION 2.3.2 Remove each under-torqued nut.
(a)
-Before further flight.ACTION 2:
Do a General Visual Inspection of
the lower gimbal assembly where
the nut was removed for any crack
and any corrosion.
-Before further flight.Install new nut at each under-
torqued nut location and tighten to
specified torque value. (b)
CONDITION 3: NO LOWER GIM-
BAL ASSEMBLY CRACK AND NO
CORROSION FOUND
-At the time specified in
Table 3.
Do the actions specified in Table 3.CONDITION 4: ANY LOWER GIM-
BAL ASSEMBLY CRACK OR ANY
CORROSION FOUND
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 07, 2024
737-27A1330 RB
15 of 46
REQUIREMENTS BULLETIN 737-27A1330
ALERTALERT

### Page 16

Table 2: On-condition corrective actions for airplanes with any under-torqued nut found.
Repeat
Interval
(Not to Ex-
ceed)
Boeing
Recommended
Compliance Time
ActionCondition
(a) Any under-torqued nut found must be replaced one at a time to maintain clamp-up of the lower gimbal
assembly.
(b) If new nut does not generate 5 in-lb of torque while installing, the fastener must be replaced. Remove the
HSTA as necessary for fastener replacement.
Table 3: On-condition corrective actions for airplanes with 3 missing nuts found in any corner and air-
planes with any lower gimbal assembly crack or any corrosion found.
Repeat
Interval
(Not to Ex-
ceed)
Boeing
Recommended
Compliance Time
ActionCondition
-Before further flight.ACTION 1:Airplanes in Table 1, CONDITION
2.1 or CONDITION 2.2.2 or Table
2, CONDITION 4
Remove the existing HSTA.
-Before further flight.ACTION 2:
Do a General Visual Inspection of
the adjacent structure for any crack
and any corrosion.
-Before further flight.Install a new or serviceable HSTA.
(a)
CONDITION 5: NO ADJACENT
STRUCTURE CRACK AND NO
CORROSION FOUND
-Before further flight.CONDITION 6 (ACTION 1):CONDITION 6: ANY ADJACENT
STRUCTURE CRACK OR ANY
CORROSION FOUND
Contact The Boeing Company for
repair instructions and do the repair.
-Before further flight.CONDITION 6 (ACTION 2):
Install a new or serviceable HSTA.
(a)
(a) A serviceable HSTA is defined as one that has been inspected for any crack and any corrosion and no
crack and no corrosion has been found and that has no under-torqued nuts at the 12 fastener locations.
Under-torqued nuts are defined in FIGURE 4 of Requirements Bulletin 737-27A1330 RB.
4. APPROVAL
This Requirements Bulletin was examined by the Federal Aviation Administration (FAA). The changes
specified in this document comply with the applicable regulations and are FAA approved, as well as European
Union Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved
airplanes listed in this Requirements Bulletin effectivity. This document and its approval were based on the
airplane in its original Boeing delivery configuration or as modified by other Boeing changes.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 07, 2024
737-27A1330 RB
16 of 46
REQUIREMENTS BULLETIN 737-27A1330
ALERTALERT

### Page 17

If an airplane has a non-Boeing modification or repair that affects a component or system also affected by
this Requirements Bulletin, the operator is responsible for obtaining appropriate regulatory agency approval
before incorporating this Requirements Bulletin.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 07, 2024
737-27A1330 RB
17 of 46
REQUIREMENTS BULLETIN 737-27A1330
ALERTALERT

### Page 18

Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 07, 2024
737-27A1330 RB
18 of 46
REQUIREMENTS BULLETIN 737-27A1330
ALERTALERT
BLANK PAGE

### Page 19

5.    ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL INFORMATION
NOTE: 1. This is an Enhanced Required for Compliance document. There will be a separate
Service Bulletin (SB) and a separate Requirements Bulletin (RB). If an RB is mandated
by an Airworthiness Directive (AD), then all applicable requirements specified in the
RB must be done. In the RB, the "Refer to the listed procedures..." column of the
table(s) in the Work Instructions is for reference only. The procedures in that column
are not required by the AD and are for guidance only. For the related SB, some
locations are marked RC Start and RC End to identify the requirements that are
restated from the RB. For the related SB, the areas between RC Start and RC End,
including sub-steps and any figures identified between RC Start and RC End, must
be done to comply with the AD. Therefore, an Alternative Method of Compliance
(AMOC) is required for any deviations to steps between RC Start and RC End,
including substeps and identified figures. For the related SB, the steps not between
RC Start and RC End may be deviated from using accepted methods in accordance
with the operator's maintenance or inspection program without obtaining approval
of an AMOC; this is provided that the steps between RC Start and RC End, including
sub-steps and identified figures, can still be done as specified, and the airplane can
be put back in an airworthy condition. Figures not required for compliance are omitted
from the RB.
2. This is an Enhanced Required for Compliance document. The Boeing processes
used to create the Service Bulletin (SB) and the Requirements Bulletin (RB) ensure
that the information between "RC Start" and "RC End" in the SB are identical to the
information in the same sections (Compliance, Work Instructions...) of the RB which
the SB refers to as the related document.
3. The compliance times for the actions in WORK INSTRUCTIONS are in Compliance.
4. Boeing Service Letter 737-SL-51-042, Damage Reporting and Repair Plan/Design
Guidelines, is an acceptable procedure to request information from Boeing for
additional structural repair instructions. The Service Letter describes what information
must be provided to Boeing before a structural repair can be provided.
5. Unless shown differently, these dimensions and tolerances are used:
– Linear dimensions are in inches
– Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus
or minus 0.03 inch
– Tolerance on rivet and bolt edge margin is plus or minus 0.05 inch
– Angular tolerance is plus or minus 2 degrees
– Hole dimensions for standard solid rivets and fasteners are in Structural Repair
Manual (SRM) Chapter 51
– Torque Values:
— Values for structural fasteners are given in 737 Structural Repair Manual,
Chapter 51.
— Values for airframe maintenance tasks are included in Chapter 20 of 737
Aircraft Maintenance Manual (AMM).
— Values for electrical maintenance tasks are included in Chapter 20 of
Standard Wiring Practices Manual (SWPM).
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 07, 2024
737-27A1330 RB
19 of 46
REQUIREMENTS BULLETIN 737-27A1330
ALERTALERT

### Page 20

— Values for engine maintenance tasks are included in Chapter 70 of 737
Aircraft Maintenance Manual (AMM).
— Non-standard torque values for maintenance tasks are included in the
applicable installation step.
6. These work instructions refer to procedures included in other Boeing documents.
When the words "refer to" are used and the operator has an accepted alternative
procedure, the accepted alternative procedure can be used. When the words "in
accordance with" are included in the instruction, the procedure in the Boeing document
must be used.
7. Where the work instructions include installation of a kept part, a new or serviceable
part with the same part number can be installed as an alternative to the kept part.
8. If it is necessary to remove more parts for access, you can remove those parts. If
you can get access without removing identified parts, it is not necessary to remove
all of the identified parts. Jacking and shoring limitations must be observed.
9. Use the approved fastener, process and material substitutions in accordance with
SRM Chapter 51.
10. A General Visual Inspection (GVI) is defined as: A visual examination of an interior
or exterior area, installation or assembly to detect obvious damage, failure or
irregularity. This level of inspection is made from within touching distance, unless
otherwise specified. A mirror may be necessary to enhance visual access to all
exposed surfaces in the inspection area. This level of inspection is made under
normally available lighting conditions such as daylight, hangar lighting, flashlight or
drop-light and may require removal or opening of access panels or doors. Stands,
ladders or platforms may be required to gain proximity to the area being checked.
Basic cleaning may be required to ensure appropriate visibility.
11. When more than one OPTION is given for a CONDITION, do only one of the OPTION
numbers. When more than one ACTION is given for a CONDITION or an OPTION,
do all of the ACTION numbers for that CONDITION or OPTION.
12. The instructions in Work Instructions and the figures can include operation of tools
or test equipment. Boeing Engineering Tool Drawings, the Illustrated Tool and
Equipment Manual, and the Special Tool and Ground Handling Drawing Index contain
data on versions of the tools or test equipment that you can use. It is permitted to
use replaced tools. It is not permitted to use superseded tools.
13. If the length of any fastener specified in this service bulletin does not meet installation
standards given in SRM Chapter 51, then a fastener of the same specification, or
an approved substitute, with a length which meets the installation standards given
in SRM Chapter 51 may be used. In addition, washers may be installed for fastener
grip length in accordance with SRM Chapter 51. Refer to SOPM 20-50-01 for alternate
full threaded fasteners (screws) needed for installation in this service bulletin.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 07, 2024
737-27A1330 RB
20 of 46
REQUIREMENTS BULLETIN 737-27A1330
ALERTALERT

### Page 21

B. WORK INSTRUCTIONS
Actions Required for Compliance
1. Requirements
Table 1: Horizontal Stabilizer Trim Actuator - Lower Gimbal Assembly Fastener Inspection and Torque
Check
Refer to the list-
ed procedures
in SB 737-
27A1330 Origi-
nal Issue or lat-
er approved revi-
sions as an ac-
cepted proce-
dure.
Method of
Compliance
ActionCondition
-APPENDIX ADo a maintenance records check to
see if the overhauled Horizontal
Stabilizer Trim Actuator (HSTA) was
inspected and corrective actions
were accomplished using the appli-
cable Boeing Provided Inspection
Requirements and Corrective Ac-
tions identified in APPENDIX A.
Airplanes with overhauled HSTA
prior to 737 AMM 27-41-81 dated
January 6, 2024.
--No further action is required.CONDITION 1: MAINTENANCE
RECORDS SHOW OVERHAULED
HSTA WAS INSPECTED AND
CORRECTIVE ACTIONS WERE
ACCOMPLISHED
Do PART 1:
PREPARATION
AND ACCESS
-Do a General Visual Inspection of
the 12 fastener locations on the
lower gimbal assembly to see if all
attachment hardware is installed.(a)
CONDITION 2: MAINTENANCE
RECORDS SHOW OVERHAULED
HSTA WAS NOT INSPECTED OR
NO MAINTENANCE RECORDS
FOUND -FIGURE 1
--Do the actions specified in Table 3.CONDITION 2.1: ATTACHMENT
HARDWARE FOUND MISSING AT
ALL 3 FASTENER LOCATIONS IN
ANY CORNER
-FIGURE 6Do a General Visual Inspection of
the lower gimbal assembly where
the attachment hardware is missing
for any crack and any corrosion.
CONDITION 2.2: ATTACHMENT
HARDWARE FOUND MISSING AT
LESS THAN 3 FASTENER LOCA-
TIONS IN ANY CORNER AND NO
CORNER WITH ATTACHMENT
HARDWARE MISSING AT ALL 3
FASTENER LOCATIONS
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 07, 2024
737-27A1330 RB
21 of 46
REQUIREMENTS BULLETIN 737-27A1330
ALERTALERT

### Page 22

Table 1: Horizontal Stabilizer Trim Actuator - Lower Gimbal Assembly Fastener Inspection and Torque
Check
Refer to the list-
ed procedures
in SB 737-
27A1330 Origi-
nal Issue or lat-
er approved revi-
sions as an ac-
cepted proce-
dure.
Method of
Compliance
ActionCondition
-FIGURE 3(c)CONDITION 2.2.1 (ACTION 1):CONDITION 2.2.1: NO LOWER
GIMBAL ASSEMBLY CRACK AND
NO CORROSION FOUND
Install new attachment hardware at
each missing location and tighten to
specified torque value. (b)
-FIGURE 4CONDITION 2.2.1 (ACTION 2):
Measure the torque value of the
HSTA lower gimbal nut at each of
the 12 fastener locations where the
nut was not missing and determine
if it is under-torqued.
Do PART 4:
RESTORATION
AND CLOSE AC-
CESS
-No further action is required.CONDITION 2.2.1.1: NO UNDER-
TORQUED NUT FOUND
--Do the actions specified in Table 2.CONDITION 2.2.1.2: ANY UNDER-
TORQUED NUT FOUND
--Do the actions specified in Table 3.CONDITION 2.2.2: ANY LOWER
GIMBAL ASSEMBLY CRACK OR
ANY CORROSION FOUND
-FIGURE 4Measure the torque value of the
HSTA lower gimbal nut at each of
the 12 fastener locations and deter-
mine if it is under-torqued.
CONDITION 2.3: NO ATTACH-
MENT HARDWARE FOUND MISS-
ING AT THE 12 FASTENER LOCA-
TIONS
Do PART 4:
RESTORATION
AND CLOSE AC-
CESS
-No further action is required.CONDITION 2.3.1: NO UNDER-
TORQUED NUT FOUND
--Do the actions specified in Table 2.CONDITION 2.3.2: ANY UNDER-
TORQUED NUT FOUND
(a) Attachment hardware is defined as any bolt, nut or washer.
(b) If new nut does not generate 5 in-lb of torque while installing, the fastener must be replaced. Remove the
HSTA as necessary for fastener replacement.
(c) FIGURE 3 gives all fastener locations. It is only necessary to install new attachment hardware at each
missing location.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 07, 2024
737-27A1330 RB
22 of 46
REQUIREMENTS BULLETIN 737-27A1330
ALERTALERT

### Page 23

Table 2: On-condition corrective actions for airplanes with any under-torqued nut found.
Refer to the list-
ed procedures
in SB 737-
27A1330 Origi-
nal Issue or lat-
er approved revi-
sions as an ac-
cepted proce-
dure.
Method of
Compliance
ActionCondition
-FIGURE 5(c)ACTION 1:Airplanes in Table 1, CONDITION
2.2.1.2 or CONDITION 2.3.2 Remove each under-torqued nut.
(a)
-FIGURE 6ACTION 2:
Do a General Visual Inspection of
the lower gimbal assembly where
the nut was removed for any crack
and any corrosion.
-FIGURE 3(d)Install new nut at each under-
torqued nut location and tighten to
specified torque value. (b)
CONDITION 3: NO LOWER GIM-
BAL ASSEMBLY CRACK AND NO
CORROSION FOUND
--Do the actions specified in Table 3.CONDITION 4: ANY LOWER GIM-
BAL ASSEMBLY CRACK OR ANY
CORROSION FOUND
(a) Any under-torqued nut found must be replaced one at a time to maintain clamp-up of the lower gimbal
assembly.
(b) If new nut does not generate 5 in-lb of torque while installing, the fastener must be replaced. Remove the
HSTA as necessary for fastener replacement.
(c) FIGURE 5 gives all fastener locations. It is only necessary to remove the nut at each location where an
under-torqued nut is found.
(d) FIGURE 3 gives all fastener locations. It is only necessary to install a new nut at each location where an
under-torqued nut was found.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 07, 2024
737-27A1330 RB
23 of 46
REQUIREMENTS BULLETIN 737-27A1330
ALERTALERT

### Page 24

Table 3: On-condition corrective actions for airplanes with 3 missing nuts found in any corner and air-
planes with any lower gimbal assembly crack or any corrosion found.
Refer to the list-
ed procedures
in SB 737-
27A1330 Origi-
nal Issue or lat-
er approved revi-
sions as an ac-
cepted proce-
dure.
Method of
Compliance
ActionCondition
Do PART 2:
HORIZONTAL
STABILIZER
TRIM ACTUA-
TOR REMOVAL
-ACTION 1:
Remove the existing HSTA.
Airplanes in Table 1, CONDITION
2.1 or CONDITION 2.2.2 or Table
2, CONDITION 4
-FIGURE 2ACTION 2:
Do a General Visual Inspection of
the adjacent structure for any crack
and any corrosion.
Do PART 3:
HORIZONTAL
STABILIZER
TRIM ACTUA-
TOR INSTALLA-
TION
-Install a new or serviceable HSTA.
(a)
CONDITION 5: NO ADJACENT
STRUCTURE CRACK AND NO
CORROSION FOUND
Do PART 4:
RESTORATION
AND CLOSE AC-
CESS
-
--CONDITION 6 (ACTION 1):CONDITION 6: ANY ADJACENT
STRUCTURE CRACK OR ANY
CORROSION FOUND
Contact The Boeing Company for
repair instructions and do the repair.
Do PART 3:
HORIZONTAL
STABILIZER
TRIM ACTUA-
TOR INSTALLA-
TION
-CONDITION 6 (ACTION 2):
Install a new or serviceable HSTA.
(a)
Do PART 4:
RESTORATION
AND CLOSE AC-
CESS
-
(a) A serviceable HSTA is defined as one that has been inspected for any crack and any corrosion and no
crack and no corrosion has been found and that has no under-torqued nuts at the 12 fastener locations.
Under-torqued nuts are defined in FIGURE 4 of Requirements Bulletin 737-27A1330 RB.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 07, 2024
737-27A1330 RB
24 of 46
REQUIREMENTS BULLETIN 737-27A1330
ALERTALERT

### Page 25 (OCR)

REQUIREMENTS BULLETIN 737-27A1330
ALERT  ALERT
JACKSCREW
FITTING
- JACKSCREW
• JACKSCREW
GEARBOX
STABILIZER
TRIM MOTOR
HORIZONTAL STABILIZER
TRIM ACTUATOR  FWD
STA CABLE
STB CABLE
3035181
FIGURE 1: HORIZONTAL STABILIZER CONTROL SYSTEM - HORIZONTAL STABILIZER TRIM ACTUATOR
- ATTACHMENT HARDWARE INSPECTION
(SHEET 1 OF 3)
Original Issue: October 07, 2024
Export Controlled ECCN: 9E991  737-27A1330 RB
See page 1 for details  25 of 46

### Page 26 (OCR)

REQUIREMENTS BULLETIN 737-27A1330
ALERT  ALERT
FWD
PARTS REMOVED
FOR CLARIT
PARTS REMOVED
FOR CLARITY
3035193
FIGURE 1: HORIZONTAL STABILIZER CONTROL SYSTEM - HORIZONTAL STABILIZER TRIM ACTUATOR
- ATTACHMENT HARDWARE INSPECTION
(SHEET 2 OF 3)
Original Issue: October 07, 2024
Export Controlled ECCN: 9E991  737-27A1330 RB
See page 1 for details  26 of 46

### Page 27

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
More DataQtyIdentificationNameTaskStep
(a)6BACN10YR4CDNUT, SELF-LOCKINGInspect1
(a)6BACW10BN4APWASHERInspect
(a)6BACB30NR4K12BOLT, HEX HEADInspect
(a)6BACW10BN4ACWASHERInspect
(a)6BACN10YR4CDNUT, SELF-LOCKINGInspect2
(a)6BACW10BN4APWASHERInspect
(a)6BACB30NR4K12BOLT, HEX HEADInspect
(a)6BACW10BN4ACWASHERInspect
(a) Do a General Visual Inspection of the 12 fastener locations on the lower gimbal assembly to see if all at-
tachment hardware is installed.
FIGURE 1: HORIZONTAL STABILIZER CONTROL SYSTEM - HORIZONTAL STABILIZER TRIM ACTUATOR
- ATTACHMENT HARDWARE INSPECTION
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 07, 2024
737-27A1330 RB
27 of 46
REQUIREMENTS BULLETIN 737-27A1330
ALERTALERT

### Page 28 (OCR)

REQUIREMENTS BULLETIN 737-27A1330
ALERT  ALERT
JACKSCREW
FITTING
- JACKSCREW
- JACKSCREW
GEARBOX
STABILIZER
TRIM MOTOR
HORIZONTAL STABILIZER
TRIM ACTUATOR  FWD
STA CABLE
STB CABLE
3035323
FIGURE 2: HORIZONTAL STABILIZER CONTROL SYSTEM - HORIZONTAL STABILIZER TRIM ACTUATOR
- ADJACENT STRUCTURE INSPECTION FOR CRACKS OR CORROSION
(SHEET 1 OF 3)
Original Issue: October 07, 2024
737-27A1330 RB
Export Controlled ECCN: 9E991
See page 1 for details  28 of 46

### Page 29 (OCR)

REQUIREMENTS BULLETIN 737-27A1330
ALERT  ALERT
INSPECTION AREA
STABILIZER TRIM ACTUATOR NOT SHOWN
3076027
FIGURE 2: HORIZONTAL STABILIZER CONTROL SYSTEM - HORIZONTAL STABILIZER TRIM ACTUATOR
- ADJACENT STRUCTURE INSPECTION FOR CRACKS OR CORROSION
(SHEET 2 OF 3)
Original Issue: October 07, 2024
Export Controlled ECCN: 9E991  737-27A1330 RB
See page 1 for details  29 of 46

### Page 30

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
More DataQtyIdentificationNameTaskStep
(a)--FITTINGInspect1
(a) Do a General Visual Inspection of the fitting and associated bushings for any crack and any corrosion.
FIGURE 2: HORIZONTAL STABILIZER CONTROL SYSTEM - HORIZONTAL STABILIZER TRIM ACTUATOR
- ADJACENT STRUCTURE INSPECTION FOR CRACKS OR CORROSION
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 07, 2024
737-27A1330 RB
30 of 46
REQUIREMENTS BULLETIN 737-27A1330
ALERTALERT

### Page 31 (OCR)

REQUIREMENTS BULLETIN 737-27A1330
ALERT  ALERT
JACKSCREW
FITTING
- JACKSCREW
• JACKSCREW
GEARBOX
STABILIZER
TRIM MOTOR
HORIZONTAL STABILIZER
TRIM ACTUATOR  FWD
STA CABLE
STB CABLE
3035243
FIGURE 3: HORIZONTAL STABILIZER CONTROL SYSTEM - HORIZONTAL STABILIZER TRIM ACTUATOR
- LOWER GIMBAL ASSEMBLY FASTENER INSTALLATION
(SHEET 1 OF 5)
Original Issue: October 07, 2024
Export Controlled ECCN: 9E991  737-27A1330 RB
See page 1 for details  31 of 46

### Page 32 (OCR)

REQUIREMENTS BULLETIN 737-27A1330
ALERT  ALERT
BOLT  BOLT
WASHER  VASHE!  7 WASHER  WASHER
NUT  NUT
BOLT
WASHER
WASHER
NUT
BOLT
WASHER
WASHER
NUT
PARTS REMOVED
FWD  FOR CLARITY
BOLT
WASHER
WASHER
NUT
\ BOLT
WASHER
WASHER
NUT
WASHER 19  BOLT  NUT  WASHER  15)  WASHER  BOLT  WASHER
NUT
BOLT
WASHER
WASHER
NUT
7 BOL
J WASHE
WASHER
NUT
PARTS REMOVED
FOR CLARITY
BOLT  BOLT
WASHER  WASHER  WASHER  WASHER  3035244
NUT  NUT
FIGURE 3: HORIZONTAL STABILIZER CONTROL SYSTEM - HORIZONTAL STABILIZER TRIM ACTUATOR
- LOWER GIMBAL ASSEMBLY FASTENER INSTALLATION
(SHEET 2 OF 5)
Original Issue: October 07, 2024
Export Controlled ECCN: 9E991  737-27A1330 RB
See page 1 for details  32 of 46

### Page 33

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
More DataQtyIdentificationNameTaskStep
Under the bolt head.
(a)(b)
1BACW10BN4ACWASHERInstall (Kept)1
(a)1BACB30NR4K12BOLT, HEX HEADInstall (Kept)
Under the nut. (b)(c)1BACW10BN4APWASHERInstall (Kept)
(c)(d)(e)1BACN10YR4CDNUT, SELF-LOCKINGInstall (New)
(a)(f)-BMS3-38CORROSION INHIBIT-
ING COMPOUND
Apply2
Under the bolt head.
(a)(b)
1BACW10BN4ACWASHERInstall (Kept)3
(a)1BACB30NR4K12BOLT, HEX HEADInstall (Kept)
Under the nut. (b)(c)1BACW10BN4APWASHERInstall (Kept)
(c)(d)(e)1BACN10YR4CDNUT, SELF-LOCKINGInstall (New)
(a)(f)-BMS3-38CORROSION INHIBIT-
ING COMPOUND
Apply4
Under the bolt head.
(a)(b)
1BACW10BN4ACWASHERInstall (Kept)5
(a)1BACB30NR4K12BOLT, HEX HEADInstall (Kept)
Under the nut. (b)(c)1BACW10BN4APWASHERInstall (Kept)
(c)(d)(e)1BACN10YR4CDNUT, SELF-LOCKINGInstall (New)
(a)(f)-BMS3-38CORROSION INHIBIT-
ING COMPOUND
Apply6
Under the bolt head.
(a)(b)
1BACW10BN4ACWASHERInstall (Kept)7
(a)1BACB30NR4K12BOLT, HEX HEADInstall (Kept)
Under the nut. (b)(c)1BACW10BN4APWASHERInstall (Kept)
(c)(d)(e)1BACN10YR4CDNUT, SELF-LOCKINGInstall (New)
(a)(f)-BMS3-38CORROSION INHIBIT-
ING COMPOUND
Apply8
FIGURE 3: HORIZONTAL STABILIZER CONTROL SYSTEM - HORIZONTAL STABILIZER TRIM ACTUATOR
- LOWER GIMBAL ASSEMBLY FASTENER INSTALLATION
(SHEET 3 OF 5)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 07, 2024
737-27A1330 RB
33 of 46
REQUIREMENTS BULLETIN 737-27A1330
ALERTALERT

### Page 34

More DataQtyIdentificationNameTaskStep
Under the bolt head.
(a)(b)
1BACW10BN4ACWASHERInstall (Kept)9
(a)1BACB30NR4K12BOLT, HEX HEADInstall (Kept)
Under the nut. (b)(c)1BACW10BN4APWASHERInstall (Kept)
(c)(d)(e)1BACN10YR4CDNUT, SELF-LOCKINGInstall (New)
(a)(f)-BMS3-38CORROSION INHIBIT-
ING COMPOUND
Apply10
Under the bolt head.
(a)(b)
1BACW10BN4ACWASHERInstall (Kept)11
(a)1BACB30NR4K12BOLT, HEX HEADInstall (Kept)
Under the nut. (b)(c)1BACW10BN4APWASHERInstall (Kept)
(c)(d)(e)1BACN10YR4CDNUT, SELF-LOCKINGInstall (New)
(a)(f)-BMS3-38CORROSION INHIBIT-
ING COMPOUND
Apply12
Under the bolt head.
(a)(b)
1BACW10BN4ACWASHERInstall (Kept)13
(a)1BACB30NR4K12BOLT, HEX HEADInstall (Kept)
Under the nut. (b)(c)1BACW10BN4APWASHERInstall (Kept)
(c)(d)(e)1BACN10YR4CDNUT, SELF-LOCKINGInstall (New)
(a)(f)-BMS3-38CORROSION INHIBIT-
ING COMPOUND
Apply14
Under the bolt head.
(a)(b)
1BACW10BN4ACWASHERInstall (Kept)15
(a)1BACB30NR4K12BOLT, HEX HEADInstall (Kept)
Under the nut. (b)(c)1BACW10BN4APWASHERInstall (Kept)
(c)(d)(e)1BACN10YR4CDNUT, SELF-LOCKINGInstall (New)
(a)(f)-BMS3-38CORROSION INHIBIT-
ING COMPOUND
Apply16
Under the bolt head.
(a)(b)
1BACW10BN4ACWASHERInstall (Kept)17
(a)1BACB30NR4K12BOLT, HEX HEADInstall (Kept)
Under the nut. (b)(c)1BACW10BN4APWASHERInstall (Kept)
(c)(d)(e)1BACN10YR4CDNUT, SELF-LOCKINGInstall (New)
(a)(f)-BMS3-38CORROSION INHIBIT-
ING COMPOUND
Apply18
FIGURE 3: HORIZONTAL STABILIZER CONTROL SYSTEM - HORIZONTAL STABILIZER TRIM ACTUATOR
- LOWER GIMBAL ASSEMBLY FASTENER INSTALLATION
(SHEET 4 OF 5)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 07, 2024
737-27A1330 RB
34 of 46
REQUIREMENTS BULLETIN 737-27A1330
ALERTALERT

### Page 35

More DataQtyIdentificationNameTaskStep
Under the bolt head.
(a)(b)
1BACW10BN4ACWASHERInstall (Kept)19
(a)1BACB30NR4K12BOLT, HEX HEADInstall (Kept)
Under the nut. (b)(c)1BACW10BN4APWASHERInstall (Kept)
(c)(d)(e)1BACN10YR4CDNUT, SELF-LOCKINGInstall (New)
(a)(f)-BMS3-38CORROSION INHIBIT-
ING COMPOUND
Apply20
Under the bolt head.
(a)(b)
1BACW10BN4ACWASHERInstall (Kept)21
(a)1BACB30NR4K12BOLT, HEX HEADInstall (Kept)
Under the nut. (b)(c)1BACW10BN4APWASHERInstall (Kept)
(c)(d)(e)1BACN10YR4CDNUT, SELF-LOCKINGInstall (New)
(a)(f)-BMS3-38CORROSION INHIBIT-
ING COMPOUND
Apply22
Under the bolt head.
(a)(b)
1BACW10BN4ACWASHERInstall (Kept)23
(a)1BACB30NR4K12BOLT, HEX HEADInstall (Kept)
Under the nut. (b)(c)1BACW10BN4APWASHERInstall (Kept)
(c)(d)(e)1BACN10YR4CDNUT, SELF-LOCKINGInstall (New)
(a)(f)-BMS3-38CORROSION INHIBIT-
ING COMPOUND
Apply24
(a) This step is only necessary if the fastener at this location is removed.
(b) Install new washer if existing was found missing. Inspect kept washer for damage. Install new washer if
kept washer is damaged. Damage is defined as any crack, deformation, or corrosion.
(c) This step is only necessary if the nut at this location is removed.
(d) If tightening the nut, tighten the nut to a torque of 63-67 in-lb. If tightening the fastener head, tighten the
fastener head to a torque of 73-77 in-lb.
(e) If new nut does not generate 5 in-lb of torque while installing, the fastener must be replaced. Remove the
HSTA as necessary for fastener replacement.
(f) Apply BMS3-38 Corrosion Inhibiting Compound to the protruded bolt end and new nut.
FIGURE 3: HORIZONTAL STABILIZER CONTROL SYSTEM - HORIZONTAL STABILIZER TRIM ACTUATOR
- LOWER GIMBAL ASSEMBLY FASTENER INSTALLATION
(SHEET 5 OF 5)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 07, 2024
737-27A1330 RB
35 of 46
REQUIREMENTS BULLETIN 737-27A1330
ALERTALERT

### Page 36 (OCR)

REQUIREMENTS BULLETIN 737-27A1330
ALERT  ALERT
JACKSCREW  FITTING
- JACKSCREW
JACKSCREW
GEARBOX
STABILIZER
TRIM MOTOR
HORIZONTAL STABILIZER
TRIM ACTUATOR  FWD
STA CABLE
STB CABLE
3035231
FIGURE 4: HORIZONTAL STABILIZER CONTROL SYSTEM - HORIZONTAL STABILIZER TRIM ACTUATOR
- NUT TORQUE CHECK
(SHEET 1 OF 3)
Original Issue: October 07, 2024
Export Controlled ECCN: 9E991  737-27A1330 RB
See page 1 for details  36 of 46

### Page 37 (OCR)

REQUIREMENTS BULLETIN 737-27A1330
ALERT  ALERT
FWD
PARTS REMOVED
FOR CLARITY
PARTS REMOVED
FOR CLARITY
3035232
FIGURE 4: HORIZONTAL STABILIZER CONTROL SYSTEM - HORIZONTAL STABILIZER TRIM ACTUATOR
- NUT TORQUE CHECK
(SHEET 2 OF 3)
Original Issue: October 07, 2024
Export Controlled ECCN: 9E991  737-27A1330 RB
See page 1 for details  37 of 46

### Page 38

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
More DataQtyIdentificationNameTaskStep
(a)6BACN10YR4CDNUT, SELF-LOCKINGTorque1
(a)6BACN10YR4CDNUT, SELF-LOCKINGTorque2
(a) Using a dial torque wrench, apply torque gradually to the nut until the nut rotates or up to 63 in-lb of torque.
If the nut rotates before 63 in-lb, the nut is under-torqued. If torque is at 63 in-lb or greater, then the nut
has passed the torque check.
FIGURE 4: HORIZONTAL STABILIZER CONTROL SYSTEM - HORIZONTAL STABILIZER TRIM ACTUATOR
- NUT TORQUE CHECK
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 07, 2024
737-27A1330 RB
38 of 46
REQUIREMENTS BULLETIN 737-27A1330
ALERTALERT

### Page 39 (OCR)

REQUIREMENTS BULLETIN 737-27A1330
ALERT  ALERT
JACKSCREW
FITTING
- JACKSCREW
• JACKSCREW
GEARBOX
STABILIZER
TRIM MOTOR
HORIZONTAL STABILIZER
TRIM ACTUATOR  FWD
STA CABLE
STB CABLE
3035233
FIGURE 5: HORIZONTAL STABILIZER CONTROL SYSTEM - HORIZONTAL STABILIZER TRIM ACTUATOR
- LOWER GIMBAL ASSEMBLY FASTENER REMOVAL
(SHEET 1 OF 4)
Original Issue: October 07, 2024
Export Controlled ECCN: 9E991  737-27A1330 RB
See page 1 for details  39 of 46

### Page 40 (OCR)

REQUIREMENTS BULLETIN 737-27A1330
ALERT  ALERT
FWD
PARTS REMOVED
FOR CLARITY
PARTS REMOVED
FOR CLARITY
3035235
FIGURE 5: HORIZONTAL STABILIZER CONTROL SYSTEM - HORIZONTAL STABILIZER TRIM ACTUATOR
- LOWER GIMBAL ASSEMBLY FASTENER REMOVAL
(SHEET 2 OF 4)
Original Issue: October 07, 2024
737-27A1330 RB
Export Controlled ECCN: 9E991
See page 1 for details  40 of 46

### Page 41

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
ONLY ONE FASTENER LOCATION CAN BE REMOVED AT A TIME.
CAUTION
More DataQtyIdentificationNameTaskStep
(a)(b)1BACN10YR4CDNUT, SELF-LOCKINGRemove1
(a)(b)(c)1BACW10BN4APWASHERRemove / Keep
(b)(c)(d)1BACW10BN4ACWASHERRemove / Keep
(b)(c)(d)1BACB30NR4K12BOLT, HEX HEADRemove / Keep
(a)(b)1BACN10YR4CDNUT, SELF-LOCKINGRemove2
(a)(b)(c)1BACW10BN4APWASHERRemove / Keep
(b)(c)(d)1BACW10BN4ACWASHERRemove / Keep
(b)(c)(d)1BACB30NR4K12BOLT, HEX HEADRemove / Keep
(a)(b)1BACN10YR4CDNUT, SELF-LOCKINGRemove3
(a)(b)(c)1BACW10BN4APWASHERRemove / Keep
(b)(c)(d)1BACW10BN4ACWASHERRemove / Keep
(b)(c)(d)1BACB30NR4K12BOLT, HEX HEADRemove / Keep
(a)(b)1BACN10YR4CDNUT, SELF-LOCKINGRemove4
(a)(b)(c)1BACW10BN4APWASHERRemove / Keep
(b)(c)(d)1BACW10BN4ACWASHERRemove / Keep
(b)(c)(d)1BACB30NR4K12BOLT, HEX HEADRemove / Keep
(a)(b)1BACN10YR4CDNUT, SELF-LOCKINGRemove5
(a)(b)(c)1BACW10BN4APWASHERRemove / Keep
(b)(c)(d)1BACW10BN4ACWASHERRemove / Keep
(b)(c)(d)1BACB30NR4K12BOLT, HEX HEADRemove / Keep
(a)(b)1BACN10YR4CDNUT, SELF-LOCKINGRemove6
(a)(b)(c)1BACW10BN4APWASHERRemove / Keep
(b)(c)(d)1BACW10BN4ACWASHERRemove / Keep
(b)(c)(d)1BACB30NR4K12BOLT, HEX HEADRemove / Keep
FIGURE 5: HORIZONTAL STABILIZER CONTROL SYSTEM - HORIZONTAL STABILIZER TRIM ACTUATOR
- LOWER GIMBAL ASSEMBLY FASTENER REMOVAL
(SHEET 3 OF 4)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 07, 2024
737-27A1330 RB
41 of 46
REQUIREMENTS BULLETIN 737-27A1330
ALERTALERT

### Page 42

More DataQtyIdentificationNameTaskStep
(a)(b)1BACN10YR4CDNUT, SELF-LOCKINGRemove7
(a)(b)(c)1BACW10BN4APWASHERRemove / Keep
(b)(c)(d)1BACW10BN4ACWASHERRemove / Keep
(b)(c)(d)1BACB30NR4K12BOLT, HEX HEADRemove / Keep
(a)(b)1BACN10YR4CDNUT, SELF-LOCKINGRemove8
(a)(b)(c)1BACW10BN4APWASHERRemove / Keep
(b)(c)(d)1BACW10BN4ACWASHERRemove / Keep
(b)(c)(d)1BACB30NR4K12BOLT, HEX HEADRemove / Keep
(a)(b)1BACN10YR4CDNUT, SELF-LOCKINGRemove9
(a)(b)(c)1BACW10BN4APWASHERRemove / Keep
(b)(c)(d)1BACW10BN4ACWASHERRemove / Keep
(b)(c)(d)1BACB30NR4K12BOLT, HEX HEADRemove / Keep
(a)(b)1BACN10YR4CDNUT, SELF-LOCKINGRemove10
(a)(b)(c)1BACW10BN4APWASHERRemove / Keep
(b)(c)(d)1BACW10BN4ACWASHERRemove / Keep
(b)(c)(d)1BACB30NR4K12BOLT, HEX HEADRemove / Keep
(a)(b)1BACN10YR4CDNUT, SELF-LOCKINGRemove11
(a)(b)(c)1BACW10BN4APWASHERRemove / Keep
(b)(c)(d)1BACW10BN4ACWASHERRemove / Keep
(b)(c)(d)1BACB30NR4K12BOLT, HEX HEADRemove / Keep
(a)(b)1BACN10YR4CDNUT, SELF-LOCKINGRemove12
(a)(b)(c)1BACW10BN4APWASHERRemove / Keep
(b)(c)(d)1BACW10BN4ACWASHERRemove / Keep
(b)(c)(d)1BACB30NR4K12BOLT, HEX HEADRemove / Keep
(a) This step is only necessary if the nut at this location needs to be removed.
(b) Use the applicable step in this figure for the location of each under-torqued nut that was found. Do the
work necessary in this figure and the subsequent actions at each location one at a time to maintain clamp-
up of the lower gimbal assembly.
(c) Discard if damaged.
(d) This step is only necessary if the fastener at this location needs to be removed.
FIGURE 5: HORIZONTAL STABILIZER CONTROL SYSTEM - HORIZONTAL STABILIZER TRIM ACTUATOR
- LOWER GIMBAL ASSEMBLY FASTENER REMOVAL
(SHEET 4 OF 4)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 07, 2024
737-27A1330 RB
42 of 46
REQUIREMENTS BULLETIN 737-27A1330
ALERTALERT

### Page 43 (OCR)

REQUIREMENTS BULLETIN 737-27A1330
ALERT  ALERT
JACKSCREW
FITTING
- JACKSCREW
• JACKSCREW
GEARBOX
STABILIZER
TRIM MOTOR
HORIZONTAL STABILIZER
TRIM ACTUATOR  FWD
STA CABLE
STB CABLE
3035236
FIGURE 6: HORIZONTAL STABILIZER CONTROL SYSTEM - HORIZONTAL STABILIZER TRIM ACTUATOR
- LOWER GIMBAL ASSEMBLY FASTENER HOLE INSPECTION
(SHEET 1 OF 3)
Original Issue: October 07, 2024
Export Controlled ECCN: 9E991  See page 1 for details  737-27A1330 RB  43 of 46

### Page 44 (OCR)

REQUIREMENTS BULLETIN 737-27A1330
ALERT  ALERT
FWD
PARTS REMOVED
FOR CLARITY
PARTS REMOVED
FOR CLARITY
AREA TO BE  3035237
INSPECTED
FIGURE 6: HORIZONTAL STABILIZER CONTROL SYSTEM - HORIZONTAL STABILIZER TRIM ACTUATOR
- LOWER GIMBAL ASSEMBLY FASTENER HOLE INSPECTION
(SHEET 2 OF 3)
Original Issue: October 07, 2024
737-27A1330 RB
Export Controlled ECCN: 9E991
See page 1 for details  44 of 46

### Page 45

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
ONLY ONE FASTENER LOCATION CAN BE INSPECTED AT ONE TIME.
CAUTION
More DataQtyIdentificationNameTaskStep
(a)(b)(c)-251A4530-2GIMBAL ASSY - STABI-
LIZER TRIM, LOWER
Inspect1
(a)(b)(c)-251A4530-2GIMBAL ASSY - STABI-
LIZER TRIM, LOWER
Inspect2
(a) Do a General Visual Inspection of the lower gimbal assembly at each fastener location where the nut was
removed or missing, for any crack or any corrosion. Refer to 737-600 SRM 51-00-06, 737-700 SRM 51-
00-06, 737-700CONV SRM 51-00-06,737-800 SRM 51-00-06, 737-800BCF SRM 51-00-06, 737-900
SRM 51-00-06 or 737-900ER SRM 51-00-06 as an accepted procedure.
(b) The locations identified are the maximum number of locations that need to be inspected.
(c) Inspect one fastener at a time to maintain clamp-up of the lower gimbal assembly.
FIGURE 6: HORIZONTAL STABILIZER CONTROL SYSTEM - HORIZONTAL STABILIZER TRIM ACTUATOR
- LOWER GIMBAL ASSEMBLY FASTENER HOLE INSPECTION
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 07, 2024
737-27A1330 RB
45 of 46
REQUIREMENTS BULLETIN 737-27A1330
ALERTALERT

### Page 46

This table is a list of the BCS messages that were sent to operators with inspection requirements and corrective
actions.
BCS MessageService Related NumberOperator Code
TBC-TBC-22-44993-5481541280TBC
TBC-0F0-22-00033-54815462160F0
TBC-P1D-22-00083-5481546096P1D
TBC-BRI-22-00143-5481541097BRI
TBC-ETH-22-00253-5481531612ETH
TBC-SFZ-22-00023-5481540836SFZ
TBC-JOY-22-00013-5481513253JOY
TBC-AMX-22-00173-5481513425AMX
TBC-TLB-22-00083-5481541185TLB
TBC-TVF-22-00033-5481513339TVF
TBC-KLM-22-00173-5481530778KLM
TBC-SCA-22-00033-5481541403SCA
TBC-JJU-22-00053-5481545975JJU
TBC-RAM-22-00113-5481531305RAM
TBC-AAR-22-00023-5481513512AAR
TBC-ANA-22-00653-5481540923ANA
TBC-TAV-22-00033-5481531039TAV
TBC-NSB-22-00103-5481545851NSB
TBC-AXE-22-00013-5481540749AXE
TBC-YYR-22-00013-5481545736YYR
TBC-RYR-22-00323-5481531451RYR
TBC-OMR-22-00063-5481541010OMR
TBC-VLS-22-00043-5481513138VLS
TBC-SHG-22-00073-5481513022SHG
TBC-MAS-22-00033-5481531175MAS
TBC-SWA-22-00593-5481513642SWA
TBC-WJI-22-00273-5481530916WJI
APPENDIX A:  BOEING PROVIDED INSPECTION REQUIREMENTS AND CORRECTIVE ACTIONS
(SHEET 1 OF 1)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 07, 2024
737-27A1330 RB
46 of 46
REQUIREMENTS BULLETIN 737-27A1330
ALERTALERT

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
