# Boeing Alert Service Bulletin 737-27A1330: No revision named, from page 37

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2025-0469, the docket of a proposed AD (Federal Register 2025-06274). Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Alert Service Bulletin 737-27A1330](https://openairdocs.org/service-documents/boeing/737-27a1330.md)
- Title as filed: RB737-27A1330 R0
- Pages: 46
- PDF: https://openairdocs.org/files/sha256/52/fb/52fbfb3fda4e4c347b5ca91bc4fcc4d94903425cdc50ac19a0270dda1befac41
- Page: https://openairdocs.org/service-documents/boeing/737-27a1330/file/52fbfb3fda4e

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 37 (OCR)

REQUIREMENTS BULLETIN 737-27A1330
ALERT  ALERT
FWD
PARTS REMOVED
FOR CLARITY
PARTS REMOVED
FOR CLARITY
3035232
FIGURE 4: HORIZONTAL STABILIZER CONTROL SYSTEM - HORIZONTAL STABILIZER TRIM ACTUATOR
- NUT TORQUE CHECK
(SHEET 2 OF 3)
Original Issue: October 07, 2024
Export Controlled ECCN: 9E991  737-27A1330 RB
See page 1 for details  37 of 46

### Page 38

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
More DataQtyIdentificationNameTaskStep
(a)6BACN10YR4CDNUT, SELF-LOCKINGTorque1
(a)6BACN10YR4CDNUT, SELF-LOCKINGTorque2
(a) Using a dial torque wrench, apply torque gradually to the nut until the nut rotates or up to 63 in-lb of torque.
If the nut rotates before 63 in-lb, the nut is under-torqued. If torque is at 63 in-lb or greater, then the nut
has passed the torque check.
FIGURE 4: HORIZONTAL STABILIZER CONTROL SYSTEM - HORIZONTAL STABILIZER TRIM ACTUATOR
- NUT TORQUE CHECK
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 07, 2024
737-27A1330 RB
38 of 46
REQUIREMENTS BULLETIN 737-27A1330
ALERTALERT

### Page 39 (OCR)

REQUIREMENTS BULLETIN 737-27A1330
ALERT  ALERT
JACKSCREW
FITTING
- JACKSCREW
• JACKSCREW
GEARBOX
STABILIZER
TRIM MOTOR
HORIZONTAL STABILIZER
TRIM ACTUATOR  FWD
STA CABLE
STB CABLE
3035233
FIGURE 5: HORIZONTAL STABILIZER CONTROL SYSTEM - HORIZONTAL STABILIZER TRIM ACTUATOR
- LOWER GIMBAL ASSEMBLY FASTENER REMOVAL
(SHEET 1 OF 4)
Original Issue: October 07, 2024
Export Controlled ECCN: 9E991  737-27A1330 RB
See page 1 for details  39 of 46

### Page 40 (OCR)

REQUIREMENTS BULLETIN 737-27A1330
ALERT  ALERT
FWD
PARTS REMOVED
FOR CLARITY
PARTS REMOVED
FOR CLARITY
3035235
FIGURE 5: HORIZONTAL STABILIZER CONTROL SYSTEM - HORIZONTAL STABILIZER TRIM ACTUATOR
- LOWER GIMBAL ASSEMBLY FASTENER REMOVAL
(SHEET 2 OF 4)
Original Issue: October 07, 2024
737-27A1330 RB
Export Controlled ECCN: 9E991
See page 1 for details  40 of 46

### Page 41

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
ONLY ONE FASTENER LOCATION CAN BE REMOVED AT A TIME.
CAUTION
More DataQtyIdentificationNameTaskStep
(a)(b)1BACN10YR4CDNUT, SELF-LOCKINGRemove1
(a)(b)(c)1BACW10BN4APWASHERRemove / Keep
(b)(c)(d)1BACW10BN4ACWASHERRemove / Keep
(b)(c)(d)1BACB30NR4K12BOLT, HEX HEADRemove / Keep
(a)(b)1BACN10YR4CDNUT, SELF-LOCKINGRemove2
(a)(b)(c)1BACW10BN4APWASHERRemove / Keep
(b)(c)(d)1BACW10BN4ACWASHERRemove / Keep
(b)(c)(d)1BACB30NR4K12BOLT, HEX HEADRemove / Keep
(a)(b)1BACN10YR4CDNUT, SELF-LOCKINGRemove3
(a)(b)(c)1BACW10BN4APWASHERRemove / Keep
(b)(c)(d)1BACW10BN4ACWASHERRemove / Keep
(b)(c)(d)1BACB30NR4K12BOLT, HEX HEADRemove / Keep
(a)(b)1BACN10YR4CDNUT, SELF-LOCKINGRemove4
(a)(b)(c)1BACW10BN4APWASHERRemove / Keep
(b)(c)(d)1BACW10BN4ACWASHERRemove / Keep
(b)(c)(d)1BACB30NR4K12BOLT, HEX HEADRemove / Keep
(a)(b)1BACN10YR4CDNUT, SELF-LOCKINGRemove5
(a)(b)(c)1BACW10BN4APWASHERRemove / Keep
(b)(c)(d)1BACW10BN4ACWASHERRemove / Keep
(b)(c)(d)1BACB30NR4K12BOLT, HEX HEADRemove / Keep
(a)(b)1BACN10YR4CDNUT, SELF-LOCKINGRemove6
(a)(b)(c)1BACW10BN4APWASHERRemove / Keep
(b)(c)(d)1BACW10BN4ACWASHERRemove / Keep
(b)(c)(d)1BACB30NR4K12BOLT, HEX HEADRemove / Keep
FIGURE 5: HORIZONTAL STABILIZER CONTROL SYSTEM - HORIZONTAL STABILIZER TRIM ACTUATOR
- LOWER GIMBAL ASSEMBLY FASTENER REMOVAL
(SHEET 3 OF 4)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 07, 2024
737-27A1330 RB
41 of 46
REQUIREMENTS BULLETIN 737-27A1330
ALERTALERT

### Page 42

More DataQtyIdentificationNameTaskStep
(a)(b)1BACN10YR4CDNUT, SELF-LOCKINGRemove7
(a)(b)(c)1BACW10BN4APWASHERRemove / Keep
(b)(c)(d)1BACW10BN4ACWASHERRemove / Keep
(b)(c)(d)1BACB30NR4K12BOLT, HEX HEADRemove / Keep
(a)(b)1BACN10YR4CDNUT, SELF-LOCKINGRemove8
(a)(b)(c)1BACW10BN4APWASHERRemove / Keep
(b)(c)(d)1BACW10BN4ACWASHERRemove / Keep
(b)(c)(d)1BACB30NR4K12BOLT, HEX HEADRemove / Keep
(a)(b)1BACN10YR4CDNUT, SELF-LOCKINGRemove9
(a)(b)(c)1BACW10BN4APWASHERRemove / Keep
(b)(c)(d)1BACW10BN4ACWASHERRemove / Keep
(b)(c)(d)1BACB30NR4K12BOLT, HEX HEADRemove / Keep
(a)(b)1BACN10YR4CDNUT, SELF-LOCKINGRemove10
(a)(b)(c)1BACW10BN4APWASHERRemove / Keep
(b)(c)(d)1BACW10BN4ACWASHERRemove / Keep
(b)(c)(d)1BACB30NR4K12BOLT, HEX HEADRemove / Keep
(a)(b)1BACN10YR4CDNUT, SELF-LOCKINGRemove11
(a)(b)(c)1BACW10BN4APWASHERRemove / Keep
(b)(c)(d)1BACW10BN4ACWASHERRemove / Keep
(b)(c)(d)1BACB30NR4K12BOLT, HEX HEADRemove / Keep
(a)(b)1BACN10YR4CDNUT, SELF-LOCKINGRemove12
(a)(b)(c)1BACW10BN4APWASHERRemove / Keep
(b)(c)(d)1BACW10BN4ACWASHERRemove / Keep
(b)(c)(d)1BACB30NR4K12BOLT, HEX HEADRemove / Keep
(a) This step is only necessary if the nut at this location needs to be removed.
(b) Use the applicable step in this figure for the location of each under-torqued nut that was found. Do the
work necessary in this figure and the subsequent actions at each location one at a time to maintain clamp-
up of the lower gimbal assembly.
(c) Discard if damaged.
(d) This step is only necessary if the fastener at this location needs to be removed.
FIGURE 5: HORIZONTAL STABILIZER CONTROL SYSTEM - HORIZONTAL STABILIZER TRIM ACTUATOR
- LOWER GIMBAL ASSEMBLY FASTENER REMOVAL
(SHEET 4 OF 4)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 07, 2024
737-27A1330 RB
42 of 46
REQUIREMENTS BULLETIN 737-27A1330
ALERTALERT

### Page 43 (OCR)

REQUIREMENTS BULLETIN 737-27A1330
ALERT  ALERT
JACKSCREW
FITTING
- JACKSCREW
• JACKSCREW
GEARBOX
STABILIZER
TRIM MOTOR
HORIZONTAL STABILIZER
TRIM ACTUATOR  FWD
STA CABLE
STB CABLE
3035236
FIGURE 6: HORIZONTAL STABILIZER CONTROL SYSTEM - HORIZONTAL STABILIZER TRIM ACTUATOR
- LOWER GIMBAL ASSEMBLY FASTENER HOLE INSPECTION
(SHEET 1 OF 3)
Original Issue: October 07, 2024
Export Controlled ECCN: 9E991  See page 1 for details  737-27A1330 RB  43 of 46

### Page 44 (OCR)

REQUIREMENTS BULLETIN 737-27A1330
ALERT  ALERT
FWD
PARTS REMOVED
FOR CLARITY
PARTS REMOVED
FOR CLARITY
AREA TO BE  3035237
INSPECTED
FIGURE 6: HORIZONTAL STABILIZER CONTROL SYSTEM - HORIZONTAL STABILIZER TRIM ACTUATOR
- LOWER GIMBAL ASSEMBLY FASTENER HOLE INSPECTION
(SHEET 2 OF 3)
Original Issue: October 07, 2024
737-27A1330 RB
Export Controlled ECCN: 9E991
See page 1 for details  44 of 46

### Page 45

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
ONLY ONE FASTENER LOCATION CAN BE INSPECTED AT ONE TIME.
CAUTION
More DataQtyIdentificationNameTaskStep
(a)(b)(c)-251A4530-2GIMBAL ASSY - STABI-
LIZER TRIM, LOWER
Inspect1
(a)(b)(c)-251A4530-2GIMBAL ASSY - STABI-
LIZER TRIM, LOWER
Inspect2
(a) Do a General Visual Inspection of the lower gimbal assembly at each fastener location where the nut was
removed or missing, for any crack or any corrosion. Refer to 737-600 SRM 51-00-06, 737-700 SRM 51-
00-06, 737-700CONV SRM 51-00-06,737-800 SRM 51-00-06, 737-800BCF SRM 51-00-06, 737-900
SRM 51-00-06 or 737-900ER SRM 51-00-06 as an accepted procedure.
(b) The locations identified are the maximum number of locations that need to be inspected.
(c) Inspect one fastener at a time to maintain clamp-up of the lower gimbal assembly.
FIGURE 6: HORIZONTAL STABILIZER CONTROL SYSTEM - HORIZONTAL STABILIZER TRIM ACTUATOR
- LOWER GIMBAL ASSEMBLY FASTENER HOLE INSPECTION
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 07, 2024
737-27A1330 RB
45 of 46
REQUIREMENTS BULLETIN 737-27A1330
ALERTALERT

### Page 46

This table is a list of the BCS messages that were sent to operators with inspection requirements and corrective
actions.
BCS MessageService Related NumberOperator Code
TBC-TBC-22-44993-5481541280TBC
TBC-0F0-22-00033-54815462160F0
TBC-P1D-22-00083-5481546096P1D
TBC-BRI-22-00143-5481541097BRI
TBC-ETH-22-00253-5481531612ETH
TBC-SFZ-22-00023-5481540836SFZ
TBC-JOY-22-00013-5481513253JOY
TBC-AMX-22-00173-5481513425AMX
TBC-TLB-22-00083-5481541185TLB
TBC-TVF-22-00033-5481513339TVF
TBC-KLM-22-00173-5481530778KLM
TBC-SCA-22-00033-5481541403SCA
TBC-JJU-22-00053-5481545975JJU
TBC-RAM-22-00113-5481531305RAM
TBC-AAR-22-00023-5481513512AAR
TBC-ANA-22-00653-5481540923ANA
TBC-TAV-22-00033-5481531039TAV
TBC-NSB-22-00103-5481545851NSB
TBC-AXE-22-00013-5481540749AXE
TBC-YYR-22-00013-5481545736YYR
TBC-RYR-22-00323-5481531451RYR
TBC-OMR-22-00063-5481541010OMR
TBC-VLS-22-00043-5481513138VLS
TBC-SHG-22-00073-5481513022SHG
TBC-MAS-22-00033-5481531175MAS
TBC-SWA-22-00593-5481513642SWA
TBC-WJI-22-00273-5481530916WJI
APPENDIX A:  BOEING PROVIDED INSPECTION REQUIREMENTS AND CORRECTIVE ACTIONS
(SHEET 1 OF 1)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 07, 2024
737-27A1330 RB
46 of 46
REQUIREMENTS BULLETIN 737-27A1330
ALERTALERT

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
