# Boeing Alert Service Bulletin 737-53A1232: Revision 3

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2016-9301; AD 2017-19-26 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Alert Service Bulletin 737-53A1232](https://openairdocs.org/service-documents/boeing/737-53a1232.md)
- Title as filed: SB-737-53A1232-03--BOEING
- Pages: 161
- PDF: https://openairdocs.org/files/sha256/15/3f/153f5b69205536487686deeb9d5e5fce0fc39f8d7d109065122158c4220e82a0
- Page: https://openairdocs.org/service-documents/boeing/737-53a1232/file/153f5b692055

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Commercial 
Airplanes
737
Service Bulletin
ALERT
Number: 737-53A1232
Original Issue: April 02, 2007
Revision 3: July 27, 2015
ATA System: 5331
SUBJECT: FUSELAGE - Skin - Chemically Milled Steps - Inspection, Repair and Preventive
Modification
Export of this technology is controlled under the United States Export Administration Regulations (EAR) (15
CFR 300-774). An export license may be required before it is used for development, production or use by foreign
persons from specific countries. The controller of this data has the individual responsibility to abide by all export
laws.
9E991ECCN:
BOEING PROPRIETARY, CONFIDENTIAL AND/OR TRADE SECRET
Copyright © 2007 Boeing.
Unpublished Work. All Rights Reserved.
Treatment of this document and its content is governed by contract with Boeing. Rights to use this document
are licensed on a per aircraft basis and such rights may not be transferable. For more information, contact The
Boeing Company.
Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner,
BBJ, DC-8, DC-9, DC-10, KC-10, KC-46, KDC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8, Poseidon and
Boeing liveries are all trademarks owned by The Boeing Company; and no trademark license is granted in
connection with this document unless provided in writing by Boeing.
Original Issue: April 02, 2007
737-53A1232Revision 3: July 27, 2015
1 of 161
4.0

### Page 2

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 02, 2007
737-53A1232Revision 3: July 27, 2015
2 of 161
BOEING SERVICE BULLETIN 737-53A1232
ALERTALERT
BLANK PAGE

### Page 3

Table of Contents
Revision Transmittal Sheet ............................................ 5
S u m m a r y  ...................................................... 7
1. PLANNING INFORMATION ........................................ 1 1
A . E f f e c t i v i t y  ............................................... 1 1
1. Airplanes ............................................ 1 1
2 . S p a r e s  A f f e c t e d  ........................................ 1 5
B. Concurrent Requirements ...................................... 1 5
C. Reason ................................................ 1 5
D. Description .............................................. 1 6
E. Compliance .............................................. 1 7
F . A p p r o v a l  ............................................... 2 2
G. Manpower .............................................. 2 3
H. Weight and Balance Changes .................................... 2 5
I. Electrical Load Data ......................................... 2 6
J . R e f e r e n c e s  .............................................. 2 6
1. Existing Data: ......................................... 2 6
2. Data Supplied with this Service Bulletin: ........................... 2 6
3. Installation Drawings Used in the Preparation of this Service Bulletin: ........... 2 6
K. Publications Affected ........................................ 2 7
L. Interchangeability and Intermixability of Parts ........................... 2 7
M. Software Accomplishment Summary ................................ 2 7
2. MATERIAL INFORMATION ........................................ 2 9
A. Material - Price and Availability ................................... 2 9
B. Industry Support Information .................................... 2 9
C. Parts Necessary for Each Airplane ................................. 2 9
1 . K i t s / P a r t s :  ........................................... 2 9
2. Parts and Materials Supplied by the Operator: ........................ 2 9
3. Parts Modified and Reidentified: ............................... 3 3
4. Parts Removed and Not Replaced: .............................. 3 3
D. Parts Necessary to Change Spares ................................. 3 4
E. Special Tooling - Price and Availability ............................... 3 4
F. Special Tooling Necessary to do this Service Bulletin ....................... 3 4
3. ACCOMPLISHMENT INSTRUCTIONS .................................. 3 5
A. GENERAL INFORMATION ..................................... 3 5
B. WORK INSTRUCTIONS ....................................... 3 6
FIGURE 1: CHEM-MILLED STEP - INSPECTION [Group 1] ....................... 4 3
FIGURE 2: CHEM-MILLED STEP - INSPECTION [Group 2] ....................... 4 7
FIGURE 3: CHEM-MILLED STEP - INSPECTION [Group 3] ....................... 5 1
FIGURE 4: CHEM-MILLED STEP - INSPECTION [Group 4] ....................... 5 5
FIGURE 5: CHEM-MILLED STEP - INSPECTION [Group 5] ....................... 5 9
FIGURE 6: CHEM-MILLED STEP - INSPECTION [Group 6] ....................... 6 3
FIGURE 7: CHEM-MILLED STEP - TYPICAL PERMANENT REPAIR .................. 6 8
FIGURE 8: CHEM-MILLED STEP - TYPICAL TIME LIMITED REPAIR ................. 7 8
FIGURE 9: CHEM-MILLED STEP - TYPICAL PERMANENT REPAIR (TIME LIMITED REPAIR
REPLACEMENT) ........................................ 8 8
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 02, 2007
737-53A1232Revision 3: July 27, 2015
3 of 161
BOEING SERVICE BULLETIN 737-53A1232
ALERTALERT

### Page 4

FIGURE 10: CHEM-MILLED STEP - REPAIR - SUPPLEMENTAL INSPECTIONS ........... 1 0 0
FIGURE 11: CHEM-MILLED STEP - TYPICAL PREVENTATIVE MODIFICATION [Group 1] ..... 1 0 3
FIGURE 12: CHEM-MILLED STEP - TYPICAL PREVENTATIVE MODIFICATION [Group 2] ..... 1 1 2
FIGURE 13: CHEM-MILLED STEP - TYPICAL PREVENTATIVE MODIFICATION [Group 3] ..... 1 2 1
FIGURE 14: CHEM-MILLED STEP - TYPICAL PREVENTATIVE MODIFICATION [Group 4] ..... 1 3 0
FIGURE 15: CHEM-MILLED STEP - TYPICAL PREVENTATIVE MODIFICATION [Group 5] ..... 1 3 9
FIGURE 16: CHEM-MILLED STEP - TYPICAL PREVENTATIVE MODIFICATION [Group 6] ..... 1 4 8
FIGURE 17: PREVENTATIVE MODIFICATION - POST MODIFICATION INSPECTION OF OUTER
F A S T E N E R  H O L E S..................................... 1 5 7
FIGURE 18: PREVENTATIVE MODIFICATION - POST MODIFICATION INSPECTION AT CHEM-MILLED
S T E P ............................................. 1 5 9
APPENDIX A: AIRPLANES WITH PREVENTATIVE MODIFICATIONS INSTALLED AFTER 30,000 TOTAL
F L I G H T  C Y C L E S . ....................................... 1 6 1
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 02, 2007
737-53A1232Revision 3: July 27, 2015
4 of 161
BOEING SERVICE BULLETIN 737-53A1232
ALERTALERT

### Page 5

Commercial 
Airplanes
737
Service Bulletin
ALERT
Revision Transmittal SheetNumber: 737-53A1232Original Issue: April 02, 2007
Revision 3: July 27, 2015
ATA System: 5331
SUBJECT: FUSELAGE - Skin - Chemically Milled Steps - Inspection, Repair and Preventive
Modification
This revision includes all pages of the service bulletin.
COMPLIANCE INFORMATION RELATED TO THIS REVISION
Federal Aviation Administration (FAA) Airworthiness Directive AD 2008-12-04 is related to this service bulletin.
Effects of this Issue on airplanes on which the Original Issue, Revision 1, or Revision 2 was previously done:
ActionConditionGroup
Do repeat inspections at the times
specified in Paragraph 1.E., Compli-
ance, and contact The Boeing
Company for work instructions be-
fore 50,000 total flight cycles and do
the work.
Airplanes with preventative modifica-
tions that were installed after 30,000
total flight cycles in accordance with
the Original Issue, Revision 1, or
Revision 2 of this service bulletin.
1, 2, 3, 4, 5, 6
REASON FOR REVISION
This revision is sent to remove the option to install the preventative modification after 30,000 total flight cycles.
These sections were changed:
1. In Summary - Background, updated information.
2. In Summary - Action, updated information.
3. In Paragraph 1.C., Reason, updated information.
4. In Paragraph 1.D., Description, added compliance information related to this revision.
5. In Paragraph 1.E., Compliance, updated compliance tables.
6. In Paragraph 1.F., Approval, updated Alternative Method of Compliance (AMOC) statement.
7. In Paragraph 1.K., Publications Affected, added information.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 02, 2007
737-53A1232Revision 3: July 27, 2015
5 of 161

### Page 6

8. In Paragraph 3.A., General Information, updated information.
9. In Paragraph 3.B., Work Instructions, updated information.
10. Added Appendix A.
Vertical lines are put on the left edge of each page, except in Paragraph 1.A., Effectivity and format changes,
to show the location of all content changes.
Pages with no vertical lines have no changes.
REVISION HISTORY
April 02, 2007Original Issue:
May 18, 2012Revision 1:
July 26, 2013Revision 2:
July 27, 2015Revision 3:
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 02, 2007
737-53A1232Revision 3: July 27, 2015
6 of 161
BOEING SERVICE BULLETIN 737-53A1232
ALERTALERT

### Page 7

Commercial 
Airplanes
737
Service Bulletin
ALERT
SummaryNumber: 737-53A1232Original Issue: April 02, 2007
Revision 3: July 27, 2015
ATA System: 5331
SUBJECT: FUSELAGE - Skin - Chemically Milled Steps - Inspection, Repair and Preventive
Modification
THIS BULLETIN IS SENT TO THE OPERATORS OF RECORD OF THE AIRPLANES SHOWN IN PARAGRAPH
1.A., EFFECTIVITY. IF AN AIRPLANE HAS BEEN LEASED OR SOLD, SEND THIS SERVICE BULLETIN TO
THE NEW OPERATOR. IF APPLICABLE SPARES HAVE BEEN SOLD, SEND THIS SERVICE BULLETIN TO
THE NEW OWNER.
CONCURRENT REQUIREMENTS
None.
BACKGROUND
During a fatigue test of a 737-800 fuselage, cracks were found in the upper skin panel at the chemically milled
step above the lap joint at Stringer-4 and Stringer-10 on both the left and right sides of the airplane. A total of
56 cracks were found in Section 43 and Section 46 with the first being found after 130,000 test cycles. Metallurgical
lab analysis indicates that the cracks originated after approximately 80,000 test cycles and took between 30,000
and 46,500 cycles to propagate from initiation until they broke through the thickness of the skin. The cracking
at the chemically milled step is caused by fatigue stresses generated by secondary bending in the lap splice. If
cracks were left undetected over a long period of time, further testing has shown that the crack tips can continue
to turn and grow to the point where the skin flaps open causing a rapid decompression event.
Cracking could develop at S-4 and S-10 in Sections 43 and 46 on all affected models. On 737-600 and -700
airplanes only, cracking could also develop at S-4 in Section 44. On 737-700C airplanes only, cracking could
also develop at the S-7L lap splice in Section 42. The S-10 splice in Section 44 has a different configuration that
did not exhibit cracking during the fatigue test. Inspection of the area will ensure the structural integrity of the
fuselage and installation of the preventative modification before 30,000 total flight cycles will stop cracks from
occurring from normal pressurization cycles before the airplane reaches its Limit of Validity (LOV).
The fuselage skin panels have been determined to be structure that is susceptible to Widespread Fatigue
Damage (WFD).
Boeing Service Related Problems (SRP) 737NG-53-0152 and 737NG-SRP-53-0472 are related to this service
bulletin.
This table is provided to operators for planning purposes only. Refer to the applicable sections for more
information.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 02, 2007
737-53A1232Revision 3: July 27, 2015
7 of 161

### Page 8

ReferenceAffectedPlanning Data
Paragraph 1.A.2., Spares AffectedNoSpares Affected
Paragraph 1.E., Compliance and Paragraph
1.F., Approval
YesAD Related
Paragraph 1.H., Weight and Balance ChangesYesWeight and Balance Change
Paragraph 1.I., Electrical Load DataNoElectrical Load Changed
Paragraph 1.K., Publications AffectedYesPublications Affected
Paragraph 1.K., Publications AffectedNoAirplane Flight Operations Affected (Flight Crew
Operations Manual and/or FAA Approved Air-
plane Flight Manual)
Paragraph 2.C.1., Kits/PartsNoKits/Parts Required
Paragraph 2.C.2., Parts and Materials Supplied
by the Operator
YesOperator Supplied Material
Paragraph 2.F., Special Tooling Necessary to
do this Service Bulletin
NoSpecial Tooling Required
ACTION
Get access to the exterior fuselage skin around S-4 and S-10 at Sections 43 and 46 on the left and right sides
of the airplane on all affected models. For 737-600 and -700 airplanes only, get access to the exterior fuselage
skin around S-4 at Section 44 on the left and right sides of the airplane. On 737-700C airplanes only, get access
to the external fuselage skin around S-7L at Section 42. Do an external detailed inspection and an external Non
Destructive Inspection (NDI) for cracking in the fuselage skin along the chemically milled step above the upper
row of the lap splice. The NDI methods that can be used are Medium Frequency Eddy Current (MFEC), Magneto
Optical Imaging (MOI), C-Scan or Ultrasonic Phased Array (UTPA). If any crack is found, cut out damaged area
of skin and repair as necessary. If no crack is found, install the preventative modification before 30,000 total
flight cycles or do the repeat inspections. If any crack is found during a repeat inspection of a permanent repair
or preventative modification, repair before further flight.
EFFECTIVITY
737-600, -700, -700C, -800 and -900 series Airplane(s). Refer to Paragraph 1.A.1., Airplanes, for the list of
affected airplane(s).
COMPLIANCE
Federal Aviation Administration (FAA) Airworthiness Directive AD 2008-12-04 is related to this service bulletin.
The effective date of AD 2008-12-04 is July 16, 2008.
Refer to Paragraph 1.E., Compliance.
INDUSTRY SUPPORT INFORMATION
Boeing warranty remedies are not available for the inspection, modification and repair procedures given in this
service bulletin.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 02, 2007
737-53A1232Revision 3: July 27, 2015
8 of 161
BOEING SERVICE BULLETIN 737-53A1232
ALERTALERT

### Page 9

MANPOWER
Elapsed HoursTotal Task HoursAirplanes
5.511Group 1 and 3
6.513Group 2
12.525Group 4
7.515Group 5
5.2510.5Group 6
NOTE: Additional time will be required for the installation of repairs and modifications or to do post modification
inspections.
MATERIAL INFORMATION
Operator Supplied Parts/Materials.
Refer to Paragraph 2.A., Material - Price and Availability.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 02, 2007
737-53A1232Revision 3: July 27, 2015
9 of 161
BOEING SERVICE BULLETIN 737-53A1232
ALERTALERT

### Page 10 (OCR)

BOEING SERVICE BULLETIN 737-53A1232
ALERT  ALERT
INSPECT SKIN FOR CRACKS AT THE
CHEMICALLY MILLED STEP, AT
STRINGERS 4 AND 10, LEFT AND RIGHT
BETWEEN STA 360 AND STA 887. DO
THE REPAIR OR MODIFICATION AS
NECESSARY.
(LEFT SIDE SHOWN, RIGHT SIDE OPPOSITE)
(737-700 SHOWN, OTHER MODELS SIMILAR)
FRAME  TYPICAL  FRAME
UPPER  C/L  CRACK  C/L
SKIN
S-4
S-10
(TYPICAL)
- c/L
LOWER
SKIN  • INSPECTION AREA
TYPICAL INSPECTION AREA  483575
Original Issue: April 02, 2007
Revision 3: July 27, 2015  PROPRIETARY - Copyright @ Unpublished  Export Controlled ECCN: 9E991 - BOEING  Work - See page 1 for details.  737-53A1232  10 of 161

### Page 11

Commercial 
Airplanes
737
Service Bulletin
ALERT
Number: 737-53A1232
Original Issue: April 02, 2007
Revision 3: July 27, 2015
ATA System: 5331
SUBJECT: FUSELAGE - Skin - Chemically Milled Steps - Inspection, Repair and Preventive
Modification
THIS BULLETIN IS SENT TO THE OPERATORS OF RECORD OF THE AIRPLANES SHOWN IN PARAGRAPH
1.A., EFFECTIVITY. IF AN AIRPLANE HAS BEEN LEASED OR SOLD, SEND THIS SERVICE BULLETIN TO
THE NEW OPERATOR. IF APPLICABLE SPARES HAVE BEEN SOLD, SEND THIS SERVICE BULLETIN TO
THE NEW OWNER.
1.    PLANNING INFORMATION
A. Effectivity
1. Airplanes
Refer to Service Bulletin Index Document D6-19567 Part 3 for Airplane Variable Number, Line
Number, and Serial Number data.
This service bulletin is for the airplanes shown below.
DESCRIPTIONCONFIGURATIONGROUP
737-600 airplanes from line number 1 thru 871.-1
737-700 airplanes from line number 1 thru 871.-2
737-700 airplanes with increased gross weight from line number 1
thru 871.
-3
737-800 airplanes from line number 1 thru 871.-4
737-900 airplanes from line number 1 thru 871.-5
737-700C airplanes from line number 1 thru 871.-6
Airplane Models:
737-600, 737-700, 737-700C, 737-800, 737-900
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 02, 2007
737-53A1232Revision 3: July 27, 2015
11 of 161

### Page 12

GroupVariable Number
2YA001 - YA099
2YA201 - YA210
2YA231 - YA242
2YA251 - YA254
2YA271 - YA272
2YA291
2YA301 - YA302
2YA311 - YA314
2YA321 - YA323
2YA336 - YA338
2YA501 - YA536
2YA541 - YA550
2YA571 - YA578
2YA601 - YA612
2YA621 - YA622
2YA626 - YA629
2YA681 - YA687
2YA701 - YA706
2YA721 - YA722
2YA731 - YA734
2YA751 - YA756
2YA801 - YA803
2YA811 - YA814
2YA831 - YA834
2YA841 - YA856
2YA881 - YA882
2YA891 - YA892
2YA961 - YA966
2YB001 - YB006
2YB101 - YB103
2YB151 - YB153
2YB161 - YB162
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 02, 2007
737-53A1232Revision 3: July 27, 2015
12 of 161
BOEING SERVICE BULLETIN 737-53A1232
ALERTALERT

### Page 13

GroupVariable Number
2YB171
2YB181
2YB201 - YB202
2YB276
2YB301
2YB501
4YC001 - YC027
4YC051 - YC068
4YC071 - YC082
4YC101 - YC104
4YC111 - YC113
4YC121
4YC126 - YC127
4YC136 - YC141
4YC146
4YC151 - YC154
4YC301 - YC303
4YC321 - YC382
4YC391 - YC392
4YC396
4YC401 - YC413
4YC416 - YC417
4YC421
4YC441 - YC447
4YC451 - YC455
4YC459
4YC461 - YC467
4YC471 - YC485
4YC501 - YC524
4YC571 - YC581
4YC587 - YC589
4YC591 - YC593
4YC601 - YC634
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 02, 2007
737-53A1232Revision 3: July 27, 2015
13 of 161
BOEING SERVICE BULLETIN 737-53A1232
ALERTALERT

### Page 14

GroupVariable Number
4YC681 - YC696
4YC701 - YC715
4YC720 - YC723
4YC727
4YC731 - YC737
4YC751 - YC752
4YC761 - YC770
4YC781 - YC793
4YC801 - YC865
4YC901 - YC906
4YC931 - YC932
4YC941 - YC947
4YC971 - YC973
4YC981 - YC983
4YD001 - YD005
4YD021 - YD025
4YD041 - YD051
4YD081 - YD084
4YD101 - YD106
4YD121 - YD125
4YD171
4YD201 - YD202
4YD301
4YD401 - YD403
5YD501 - YD505
5YD531
5YD601 - YD602
1YE001 - YE020
1YE051
1YE101 - YE109
1YE151 - YE157
1YE171 - YE172
3YG001 - YG040
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 02, 2007
737-53A1232Revision 3: July 27, 2015
14 of 161
BOEING SERVICE BULLETIN 737-53A1232
ALERTALERT

### Page 15

GroupVariable Number
3YG061 - YG064
3YG066 - YG077
6YG501 - YG504
2. Spares Affected
None.
B. Concurrent Requirements
None.
C. Reason
During a fatigue test of a 737-800 fuselage, cracks were found in the upper skin panel at the chemically
milled step above the lap joint at Stringer-4 and Stringer-10 on both the left and right sides of the
airplane. A total of 56 cracks were found in Section 43 and Section 46 with the first being found after
130,000 test cycles. Metallurgical lab analysis indicates that the cracks originated after approximately
80,000 test cycles and took between 30,000 and 46,500 cycles to propagate from initiation until they
broke through the thickness of the skin. The cracking at the chemically milled step is caused by fatigue
stresses generated by secondary bending in the lap splice. If cracks were left undetected over a long
period of time, further testing has shown that the crack tips can continue to turn and grow to the point
where the skin flaps open causing a rapid decompression event.
Cracking could develop at S-4 and S-10 in Sections 43 and 46 on all affected models. On 737-600 and
-700 airplanes only, cracking could also develop at S-4 in Section 44. On 737-700C airplanes only,
cracking could also develop at the S-7L lap splice in Section 42. The S-10 splice in Section 44 has a
different configuration that did not exhibit cracking during the fatigue test. Inspection of the area will
ensure the structural integrity of the fuselage and installation of the preventative modification before
30,000 total flight cycles will stop cracks from occurring from normal pressurization cycles before the
airplane reaches its Limit of Validity (LOV).
The fuselage skin panels have been determined to be structure that is susceptible to Widespread
Fatigue Damage (WFD).
Boeing Service Related Problems (SRP) 737NG-53-0152  and 737NG-SRP-53-0472 are related to
this service bulletin.
Revision 1 was sent to add new inspection requirements to the Compliance section, Accomplishment
Instructions and Figures, incorporate drawing changes and add a new figure.
Revision 2 was sent to update compliance tables, correct typographical errors in the work instructions
and to provide instructions for the installation of a preventive modification for short edge margin
conditions.
Revision 3 is sent to remove the option to install the preventative modification after 30,000 total flight
cycles.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 02, 2007
737-53A1232Revision 3: July 27, 2015
15 of 161
BOEING SERVICE BULLETIN 737-53A1232
ALERTALERT

### Page 16

D. Description
Get access to the exterior fuselage skin around S-4 and S-10 at Sections 43 and 46 on the left and
right sides of the airplane on all affected models. For 737-600 and -700 airplanes only, get access to
the exterior fuselage skin around S-4 at Section 44 on the left and right sides of the airplane. On
737-700C airplanes only, get access to the external fuselage skin around S-7L at Section 42. Do an
external detailed inspection and an external Non Destructive Inspection (NDI) for cracking in the fuselage
skin along the chemically milled step above the upper row of the lap splice. The NDI methods that can
be used are Medium Frequency Eddy Current (MFEC), Magneto Optical Imaging (MOI), C-Scan or
Ultrasonic Phased Array (UTPA). If any crack is found, cut out damaged area of skin and repair as
necessary. If no crack is found, install the preventative modification before 30,000 total flight cycles or
do the repeat inspections. If any crack is found during a repeat inspection of a permanent repair or
preventative modification, repair before further flight.
Effects of this Issue on airplanes on which the Original Issue, Revision 1, or Revision 2 was previously
done:
ActionConditionGroup
Do repeat inspections at the times
specified in Paragraph 1.E., Compli-
ance, and contact The Boeing
Company for work instructions be-
fore 50,000 total flight cycles and do
the work.
Airplanes with preventative modifica-
tions that were installed after 30,000
total flight cycles in accordance with
the Original Issue, Revision 1, or
Revision 2 of this service bulletin.
1, 2, 3, 4, 5, 6
The work in this service bulletin is done in the maintenance zone(s) given below.
Group 1:
Affected Maintenance Zones
ZoneModel
221, 222, 231, 232, 241, 242737-600
Group 2-3:
Affected Maintenance Zones
ZoneModel
221, 222, 231, 232, 241, 242737-700
Group 4:
Affected Maintenance Zones
ZoneModel
221, 222, 231, 232, 241, 242737-800
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 02, 2007
737-53A1232Revision 3: July 27, 2015
16 of 161
BOEING SERVICE BULLETIN 737-53A1232
ALERTALERT

### Page 17

Group 5:
Affected Maintenance Zones
ZoneModel
221, 222, 231, 232, 241, 242737-900
Group 6:
Affected Maintenance Zones
ZoneModel
221, 222, 231, 232, 241, 242737-700C
E. Compliance
Federal Aviation Administration (FAA) Airworthiness Directive AD 2008-12-04 is related to this service
bulletin. The effective date of AD 2008-12-04 is July 16, 2008.
For airplanes which have incorporated Boeing Business Jet Lower Cabin Altitude Supplemental Type
Certificate ST01697SE (6,500 feet maximum cabin altitude in lieu of 8,000 feet) as referenced in Boeing
Service Bulletin 737-21-1149, the flight cycle related compliance times are different from those specified
in this service bulletin. All initial compliance times (thresholds) specified in flight cycles must be reduced
to 1/2 of those specified in this service bulletin. All repeat interval compliance times specified in flight
cycles must be reduced to 1/4 of those specified.
For airplanes which have incorporated Boeing Business Jet Lower Cabin Altitude Supplemental Type
Certificate ST0169SE, new installation of the preventative modification is limited to airplanes with
15,000 total flight cycles or less. For airplanes that have incorporated the preventative modification
after 15,000 total flight cycles in accordance with the Original Issue, Revision 1, or Revision 2 of the
service bulletin, operators must contact The Boeing Company for work instructions before 25,000 total
flight cycles and do the work. All total flight cycles in the condition columns are 1/2 of those specified
in this service bulletin.
Do the required actions in accordance with Paragraph 3. Accomplishment Instructions.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 02, 2007
737-53A1232Revision 3: July 27, 2015
17 of 161
BOEING SERVICE BULLETIN 737-53A1232
ALERTALERT

### Page 18

Table 1: Inspection Requirements of the skin at the chem-milled pockets above the lap joints at S-4, S-
10 and S-7L for airplanes without the preventative modification, time-limited repair or permanent repair
installed.
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
1,500 flight cycles
after an Option 1 in-
spection. 2,100 flight
cycles after an Op-
tion 2 inspection. (a)
(b)
Before 35,000 total flight
cycles, or within 36 months
after the effective date of
AD 2008-12-04, whichever
occurs later.
Do an external detailed inspection and an
external Non Destructive Inspection (NDI) for
any crack in the fuselage skin at the chem-
milled steps at specified locations in accor-
dance with Accomplishment Instruction "PART
l - INSPECTION" using one of the following
NDI options: (a) (c)
Airplanes
without the
preventative
modification,
time-limited
repair or per-
manent re-
pair installed
in accor-
dance with
this service
bulletin.
Option 1: Do an external Medium Frequency
Eddy Current (MFEC) or Magneto Optic Im-
ager (MOI) or C-Scan inspection.
OR
Option 2: Do an external Ultrasonic Phased
Array Inspection (UTPA).
-Before further flight.Repair any crack that is found in accordance
with "PART III - PERMANENT REPAIR" or
"PART IV - TIME LIMITED REPAIR".
Any crack is
found in the
skin.
(a) Repeat inspection is terminated when one of the following is accomplished:
– The preventative modification is installed, or
– The time limited repair is installed, or
– The permanent repair is installed
New installation of the preventative modification is limited to airplanes with 30,000 total flight cycles or
less. For airplanes which have incorporated Boeing Business Jet Lower Cabin Altitude Supplemental
Type Certificate STOI 697SE, new installation of the preventative modification is limited to airplanes with
15,000 total flight cycles or less.
New inspection of the installed preventative modification, time limited repair or Permanent repair is required.
Refer to subsequent compliance times for the airplane condition described.
(b) It is acceptable to change inspection procedures from Option 1 to Option 2 or from Option 2 to Option 1
if the inspection is done before the time given in the repeat interval column.
(c) MOI and C-Scan inspections cannot be used within 4 inches of an existing repair doubler edge. Within 4
inches of an existing repair doubler edge, the MFEC or UTPA inspection must be used.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 02, 2007
737-53A1232Revision 3: July 27, 2015
18 of 161
BOEING SERVICE BULLETIN 737-53A1232
ALERTALERT

### Page 19

Table 1a: Post modification inspection of the skin at the chem-milled step for airplanes with the preven-
tative modification installed at locations that do not have time-limited repair or permanent repairs.
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
-Before 50,000 total
flight cycles.
Inspect for any crack in the fuselage
skin at the chem-milled steps at the
specified locations in accordance
with Accomplishment Instructions
"PART 7: POST PREVENTATIVE
MODIFICATION INSPECTION".
Airplanes with preventative
modifications installed AT OR
BEFORE 30,000 total flight cy-
cles.
-Within 3,200 flight cy-
cles after the modifica-
tion doubler is in-
stalled, or within
1,500 flight cycles af-
ter the date of Revi-
sion 2 of this service
bulletin, whichever
occurs later.
Inspect for any crack in the fuselage
skin at the chem-milled steps at the
specified locations in accordance
with Accomplishment Instructions
"PART 7: POST PREVENTATIVE
MODIFICATION INSPECTION".
Airplanes with preventative
modifications installed AFTER
30,000 total flight cycles.
-Before 50,000 total
flight cycles.
Contact The Boeing Company for
work instructions and do the work.
(a)
-Before further flight.Contact The Boeing Company for
work instructions and do the work.
Any crack found.
3,200 flight cy-
cles.
-Inspect for any crack in the fuselage
skin at the chem-milled steps at the
specified locations in accordance
with Accomplishment Instructions
"PART 7: POST PREVENTATIVE
MODIFICATION INSPECTION".
No crack found.
(a) Airplanes listed in APPENDIX A have been evaluated by The Boeing Company for the preventative
modifications installed at the listed flight cycles. These airplanes are not required to contact The Boeing
Company for work instructions only for the preventative modifications installed at the listed flight cycles.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 02, 2007
737-53A1232Revision 3: July 27, 2015
19 of 161
BOEING SERVICE BULLETIN 737-53A1232
ALERTALERT

### Page 20

Table 1b: Post modification inspection of fasteners in the chem-milled pocket on the periphery of the
preventative modification at locations that do not have time-limited or permanent repairs.
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
11,500 flight cycles.Within 50,000 flight cycles
after the modification dou-
bler is installed.
Do an High Frequency Eddy Current (HFEC)
inspection for any crack in accordance with
Accomplishment Instructions "PART 7: POST
PREVENTATIVE MODIFICATION INSPEC-
TION".
Preventative
modifications
installed in
accordance
with this ser-
vice bulletin. 5,500 flight cycles.Within 50,000 flight cycles
after the modification dou-
bler is installed.
Do a detailed inspection for any crack and
any loose or missing fasteners in accordance
with Accomplishment Instructions "PART 7:
POST PREVENTATIVE MODIFICATION IN-
SPECTION".
-Before further flight.Contact The Boeing Company for work instruc-
tions and do the work.
Any crack
found in the
skin.
-Before further flight.Replace the fastener in accordance with
"PART V - PREVENTATIVE MODIFICA-
TION".
Any loose or
missing fas-
tener.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 02, 2007
737-53A1232Revision 3: July 27, 2015
20 of 161
BOEING SERVICE BULLETIN 737-53A1232
ALERTALERT

### Page 21

Table 2: Inspection Requirements for airplanes with the Permanent chem-milled step repair installed.
Repeat Inter-
val (Not to Ex-
ceed)
Compliance TimeActionOptionCondition
1,100 flight cy-
cles.
Before 50,000 total flight cycles, or
within 7,300 flight cycles after the
permanent repair is installed, or within
36 months after the effective date of
AD 2008-12-04, whichever occurs
latest.
Do an external Low Fre-
quency Eddy Current
(LFEC) Inspection for any
crack in accordance with
Accomplishment Instruc-
tions "PART III - PERMA-
NENT REPAIR".
Skin In-
spection
Option 1
Airplanes with
the permanent
repair installed
in accordance
with this ser-
vice bulletin.
4,500 flight cy-
cles.
Before 50,000 total flight cycles, or
within 7,300 flight cycles after the
permanent repair is installed, or within
36 months after the effective date of
AD 2008-12-04, whichever occurs
latest.
Doubler Inspection: Do an
external LFEC Inspection
for any crack and an exter-
nal Detailed Inspection for
any crack and loose/miss-
ing fasteners in accordance
with Accomplishment In-
structions "PART III - PER-
MANENT REPAIR".
4,500 flight cy-
cles.
Before 50,000 total flight cycles, or
within 7,300 flight cycles after the
permanent repair is installed, or within
36 months after the effective date of
AD 2008-12-04, whichever occurs
latest.
Do an external LFEC In-
spection for any crack in
accordance with Accom-
plishment Instructions
"PART III - PERMANENT
REPAIR".
Skin In-
spection
Option 2
8,000 flight cy-
cles.
Before 50,000 total flight cycles, or
within 7,300 flight cycles after the
permanent repair is installed, or within
36 months after the effective date of
AD 2008-12-04, whichever occurs
latest.
Do an internal Medium Fre-
quency Eddy Current
(MFEC) Inspection for any
crack in accordance with
Accomplishment Instruc-
tions "PART III - PERMA-
NENT REPAIR".
4,500 flight cy-
cles.
Before 50,000 total flight cycles, or
within 7,300 flight cycles after the
permanent repair is installed, or within
36 months after the effective date of
AD 2008-12-04, whichever occurs
latest.
Doubler Inspection: Do an
external LFEC Inspection
for any crack and an exter-
nal Detailed Inspection for
any crack and loose/miss-
ing fasteners in accordance
with Accomplishment In-
structions "PART III - PER-
MANENT REPAIR".
-Before further flight.Contact The Boeing Compa-
ny for work instructions and
do the work.
Any crack is found in the
skin.
-Before further flight.Replace any loose or miss-
ing fastener.
Any loose or missing fas-
tener.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 02, 2007
737-53A1232Revision 3: July 27, 2015
21 of 161
BOEING SERVICE BULLETIN 737-53A1232
ALERTALERT

### Page 22

Table 3: Inspection Requirements for airplanes with a chem-milled step Time-Limited repair.
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
2,500 Flight Cy-
cles. (a)
Within 2,500 Flight
Cycles after installa-
tion of the time limited
repair or within 24
months after the effec-
tive date of AD 2008-
12-04, whichever oc-
curs later.
Internal/External Detailed Inspection
of a time limited repair for any crack
and loose or missing fasteners in accor-
dance with Accomplishment Instruc-
tions "PART IV - TIME LIMITED RE-
PAIR". (a)
Airplanes with the
time limited repair
installed in accor-
dance with this
service bulletin.
-Within 7,300 Flight
Cycles after installa-
tion of the time limited
repair or within 24
months after the effec-
tive date of AD 2008-
12-04, whichever oc-
curs later.
Replace the time limited repair with the
permanent repair in accordance with
Accomplishment Instructions "PART
IV - TIME LIMITED REPAIR".
-Before further flight.Repair any crack found in accordance
with Accomplishment Instructions
"PART IV - TIME LIMITED REPAIR".
Any crack is found
in the skin.
-Before further flight.Replace any loose or missing fastener.Any loose or miss-
ing fastener.
(a) Repeat inspection is terminated when the permanent repair is accomplished. New inspection
of the installed permanent repair is required; Refer to Table 2 for actions and compliance times.
F. Approval
This service bulletin was examined by the Federal Aviation Administration (FAA). The changes specified
in this service bulletin comply with the applicable regulations and are FAA approved, as well as European
Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved
airplanes listed in the service bulletin effectivity. This service bulletin and its approval were based on
the airplane in its original Boeing delivery configuration or as modified by other approved Boeing
changes.
If an airplane has a non-Boeing modification or repair that affects a component or system also affected
by this service bulletin, the operator is responsible for obtaining appropriate regulatory agency approval
before incorporating this service bulletin.
This service bulletin has been approved by the FAA. In addition, the Manager of the Seattle Aircraft
Certification Office approves the inspection methods and repair and preventative modification procedures
with the corresponding compliance times specified in Tables 1, 1a, 1b, 2 and 3, under Paragraph 1.E.,
"Compliance," of Service Bulletin 737-53A1232, Revision 3, as an Alternative Method of Compliance
(AMOC) to the inspection methods and repair and preventative modification procedures with the
corresponding compliance times specified in Tables 1, 2 and 3, under Paragraph 1.E., "Compliance,"
of Service Bulletin 737-53-1232, Original Issue, dated April 2, 2007, required by paragraphs (g), (h)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 02, 2007
737-53A1232Revision 3: July 27, 2015
22 of 161
BOEING SERVICE BULLETIN 737-53A1232
ALERTALERT

### Page 23

and (i) of AD 2008-12-04. All provisions of AD 2008-12-04 that are not specifically referenced in the
preceding sentence remain fully applicable and must be complied with accordingly. Where Boeing
Service Bulletin 737-53-1232, Revision 3, specifies to contact The Boeing Company for repair
instructions, before further flight, repair using a method approved in accordance with the procedures
specified in paragraph (l) of AD 2008-12-04.
G. Manpower
The table below shows an estimate of the task hours necessary to do the inspection only, for each
airplane. Time for the repairs/preventative modifications are not given in the table below, because of
the differences from airplane to airplane. Manpower requirements for repairs/preventative modifications
are dependant on the quantity of repairs/preventative modifications. This estimate is for direct labor
only, done by an experienced crew. Adjust the estimate with operator task-hour data if necessary. The
estimate does not include lost time. These are some examples of lost time:
— Time to adjust to the workplace
— Time to schedule the work
— Time to examine the work
— Time to cure the materials
— Time to make the parts
— Time to find the tools.
Group 1:
Elapsed
Hours
Task HoursNumber of
Persons
Task
5.5112Figure 1
5.511TOTAL FOR EACH AIRPLANE: (a) (b)
(a) The inspection time given is for the Eddy Current inspection method. More
or less time can be required for alternative inspection methods.
(b) Additional time will be required for the installation of repairs and modifica-
tions or to do post modification inspections.
Group 2:
Elapsed
Hours
Task-HoursNumber of
Persons
Task
6.5132Figure 2
6.513TOTAL FOR EACH AIRPLANE: (a) (b)
(a) The inspection time given is for the Eddy Current inspection method. More
or less time can be required for alternative inspection methods.
(b) Additional time will be required for the installation of repairs and modifica-
tions or to do post modification inspections.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 02, 2007
737-53A1232Revision 3: July 27, 2015
23 of 161
BOEING SERVICE BULLETIN 737-53A1232
ALERTALERT

### Page 24

Group 3:
Elapsed
Hours
Task-HoursNumber of
Persons
Task
5.5112Figure 3
5.511TOTAL FOR EACH AIRPLANE: (a) (b)
(a) The inspection time given is for the Eddy Current inspection method. More
or less time can be required for alternative inspection methods.
(b) Additional time will be required for the installation of repairs and modifica-
tions or to do post modification inspections.
Group 4:
Elapsed
Hours
Task-HoursNumber of
Persons
Task
12.5252Figure 4
12.525TOTAL FOR EACH AIRPLANE: (a) (b)
(a) The inspection time given is for the Eddy Current inspection method. More
or less time can be required for alternative inspection methods.
(b) Additional time will be required for the installation of repairs and modifica-
tions or to do post modification inspections.
Group 5:
Elapsed
Hours
Task-HoursNumber of
Persons
Task
7.5152Figure 5
7.515TOTAL FOR EACH AIRPLANE: (a) (b)
(a) The inspection time given is for the Eddy Current inspection method. More
or less time can be required for alternative inspection methods.
(b) Additional time will be required for the installation of repairs and modifica-
tions or to do post modification inspections.
Group 6:
Elapsed
Hours
Task-HoursNumber of
Persons
Task
5.2510.52Figure 6
5.2510.5TOTAL FOR EACH AIRPLANE: (a) (b)
(a) The inspection time given is for the Eddy Current inspection method. More
or less time can be required for alternative inspection methods.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 02, 2007
737-53A1232Revision 3: July 27, 2015
24 of 161
BOEING SERVICE BULLETIN 737-53A1232
ALERTALERT

### Page 25

Group 6:
Elapsed
Hours
Task-HoursNumber of
Persons
Task
(b) Additional time will be required for the installation of repairs and modifica-
tions or to do post modification inspections.
H. Weight and Balance Changes
Preventative modification (Refer to Figures 11, 12, 13, 14, 15 and 16).
— Change in weight = + 0.40 pounds.
Permanent repair (Refer to Figure 7).
— Change in weight = + 2.00 pounds.
Time limited repair (Refer to Figure 8).
— Change in weight = + 2.00 pounds.
Permanent repair (time limited repair replacement) (Refer to Figure 9).
— Change in weight = + 2.00 pounds.
The Change in Moment is calculated for each preventative modification and for each Repair. These
values are then summed. Refer to the following process.
Group 1:
1. Measure the straight-line "X" distance in inches from the airplane's Station 360 frame to the center
of the repair. The Station 360 frame is 32 inches aft of the center line of the left forward door. Add
334 inches to get the Balance Arm (BA). Multiply the BA times the weight of each repair or
modification (2.00 for repair or 0.40 for modification). The product is the desired "Change in
Moment". Record the value.
Group 2-3, 6:
1. Measure the straight-line "X" distance in inches from the airplane's Station 360 frame to the center
of the repair. The Station 360 frame is 32 inches aft of the center line of the left forward door. Add
280 inches to get the Balance Arm (BA). Multiply the BA times the weight of the repair or modification
(2.00 for repair or 0.40 for modification). The product is the desired "Change in Moment". Record
the value.
Group 4:
1. Measure the straight-line "X" distance in inches from the airplane's Station 360 frame to the center
of the repair. The Station 360 frame is 32 inches aft of the center line of the left forward door. Add
162 inches to get the Balance Arm (BA). Multiply the BA times the weight of the repair or modification
(2.00 for repair or 0.40 for modification). The product is the desired "Change in Moment". Record
the value.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 02, 2007
737-53A1232Revision 3: July 27, 2015
25 of 161
BOEING SERVICE BULLETIN 737-53A1232
ALERTALERT

### Page 26

Group 5:
1. Measure the straight-line "X" distance in inches from the airplane's Station 360 frame to the center
of the repair. The Station 360 frame is 32 inches aft of the center line of the left forward door. Add
100 inches to get the Balance Arm (BA). Multiply the BA times the weight of the repair or modification
(2.00 for repair or 0.40 for modification). The product is the desired "Change in Moment". Record
the value.
Example: A Group 2 airplane received two preventative modifications, one on each side of the airplane
at "X" distance of 100 inches. The airplane also received two permanent repairs (Figure 7), one at "X"
distance of 687 inches and one at "X" distance of 767 inches. What is the change in moment?
Answer: (2)(100+280)(0.40) = 304 pound-inches for the two preventative modifications and
(687+280)(2.00) = 1,934 pound-inches and (767+280)(2.00) = 2,094 pound-inches for the permanent
repairs. Sum totals 304 + 1,934 + 2,094 = 4,332 pound-inches total effect.
I. Electrical Load Data
Not changed.
J. References
1. Existing Data:
a. Boeing Service Bulletin 737-21-1149
b. Boeing Service Letter 737-SL-51-042
c. Boeing Service Related Problem (SRP) 737NG-53-0152
d. Federal Aviation Administration (FAA) Airworthiness Directive (AD) 2008-12-04.
e. Standard Overhaul Practices Manual (SOPM) 20-41-02, 20-43-03, 20-50-19
f. 737 Non-Destructive Testing (NDT) Manual Part 4, 53-30-07, Part 6, 51-00-00, Part 6, 53-30-09,
Part 6, 53-30-18, Part 6, 53-30-19, Part 6, 53-30-23, Part 6, 53-30-25
g. 737-600/700/800/900 Aircraft Maintenance Manual (AMM) 25-21-45, 25-21-46, 25-22-00,
25-23-61, 25-24-31, 25-80-00
h. 737-600/700/800/900 Structural Repair Manual (SRM) 51-40-08, 53-00-01
2. Data Supplied with this Service Bulletin:
None.
3. Installation Drawings Used in the Preparation of this Service Bulletin:
TitleDrawing Number
Skin-Installation - S-4L to S-4R, STA 360 to 540143A3110
Skin-Installation - S-4 to S-10, STA 360 to 540143A3130
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 02, 2007
737-53A1232Revision 3: July 27, 2015
26 of 161
BOEING SERVICE BULLETIN 737-53A1232
ALERTALERT

### Page 27

TitleDrawing Number
Skin-Installation - S-10 to S-14, STA 360 to 540143A3150
Skin-Installation - S-9L to S-9R, STA 540 to 727144A3101
Skin-Installation - S-4L to S-4R, STA 727 to 888146A3100
Skin-Installation - S-4 to S-10, STA 727 to 888146A3130
Skin-Installation - S-10 to S-14, STA 727 to 888146A3150
These drawings were used to prepare this service bulletin. These drawings are not necessary to
make the specified changes, and are not supplied with this service bulletin. These drawings may
not be applicable to all airplane configurations or operators.
K. Publications Affected
1. Publications:
Chapter-SectionPublication
53-31737 Illustrated Parts Catalog
2. Damage Tolerance Based Structural Inspections:
Boeing has evaluated the repairs and/or changes in this service bulletin for effects on Fatigue
Critical Structure (FCS) and for changes to Damage Tolerance Inspections (DTI) required in the
Maintenance Program. This service bulletin affects FCS. DTI requirements for the structure affected
are contained in Paragraph 1.E., Compliance of this service bulletin.
L. Interchangeability and Intermixability of Parts
Accomplishment of this service bulletin does not affect interchangeability or intermixability of parts.
M. Software Accomplishment Summary
Not affected.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 02, 2007
737-53A1232Revision 3: July 27, 2015
27 of 161
BOEING SERVICE BULLETIN 737-53A1232
ALERTALERT

### Page 28

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 02, 2007
737-53A1232Revision 3: July 27, 2015
28 of 161
BOEING SERVICE BULLETIN 737-53A1232
ALERTALERT
BLANK PAGE

### Page 29

2.    MATERIAL INFORMATION
A. Material - Price and Availability
The operator can supply the parts and materials shown in Paragraph 2.C., Parts Necessary For Each
Airplane. As an alternative, operators can purchase the parts from Boeing Spares. This service bulletin
does not show the Boeing price and supply data.
B. Industry Support Information
Boeing warranty remedies are not available for the inspection, modification and repair procedures given
in this service bulletin.
C. Parts Necessary for Each Airplane
1. Kits/Parts:
None.
2. Parts and Materials Supplied by the Operator:
NOTE: The parts listed below are an estimate of the materials needed to accomplish a typical
permanent repair in accordance with Figure 7 at a single location. Fastener quantity and
grip length may vary depending on the specific location of the repair.
After 225,000 pressurization cycles of a fuselage fatigue test on a 737-800, a total of 56
cracks were found at different locations.
The maximum number of repair locations affected by this bulletin is 102 for Group 1, 122
for Group 2, 104 for Group 3, 144 for Group 4, 168 for Group 5 and 83 for Group 6.
Permanent Repair
NotesNameQTYPart Number / Specifica-
tion
(a) approximate size 22 x
12 inches.
Doubler1A
(a) approximate size 22 x
10 inches.
Tripler1B
(a) approximate size 24 x 3
inches.
Filler1C
(a) approximate size 24 x 4
inches.
Filler1D
Chemical Conversion
Coating
2
Ounce
Alodine 1200S Type I,
Class A (or equivalent)
(b)Primer2
Ounce
BMS 10-11, Type I
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 02, 2007
737-53A1232Revision 3: July 27, 2015
29 of 161
BOEING SERVICE BULLETIN 737-53A1232
ALERTALERT

### Page 30

Permanent Repair
NotesNameQTYPart Number / Specifica-
tion
(b)Sealant4
Ounce
BMS 5-95 Type I or II,
Class B 1/2 or 2.
(c) (d)Rivet76BACR15FT7D7
(c) (d)Rivet68BACR15FT6D5
(c) (d)Rivet88BACR15FT6D6
(e)Rivet (Countersink Re-
pair Washer)
76BACR15GF6D( )
(a) Fabricate from 2024-T3 clad sheet, 0.032 inch thick in accordance with Figure 7.
(b) See the Qualified Products List at the end of the Boeing Material Specification (BMS)
for supplier data.
(c) Refer to 737 Structural Repair Manual Chapter 51 for alternative fasteners.
(d) Rivet length determined on installation. Longer rivets may be required depending on
specific location. More rivet quantities may be required depending on specific location.
(e) Use these rivets to make the countersink repair washers. Any length rivet can be used
to make a countersink repair washer.
NOTE: The parts listed below are an estimate of the materials needed to accomplish a typical
time limited repair in accordance with Figure 8 at a single location. Fastener quantity and
grip length may vary depending on the specific location of the repair.
After 225,000 pressurization cycles of a fuselage fatigue test on a 737-800, a total of 56
cracks were found at different locations.
The maximum number of repair locations affected by this bulletin is 102 for Group 1, 122
for Group 2, 104 for Group 3, 144 for Group 4, 168 for Group 5 and 83 for Group 6.
Time Limited Repair
NotesNameQTYPart Number / Specifi-
cation
(a) approximate size 22 x
12 inches.
Doubler1A
(a) approximate size 22 x
10 inches.
Tripler1B
(a) approximate size 24 x 3
inches.
Filler1C
(a) approximate size 24 x 4
inches.
Filler1D
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 02, 2007
737-53A1232Revision 3: July 27, 2015
30 of 161
BOEING SERVICE BULLETIN 737-53A1232
ALERTALERT

### Page 31

Time Limited Repair
NotesNameQTYPart Number / Specifi-
cation
Chemical Conversion
Coating
2
Ounce
Alodine 1200S Type I,
Class A (or equivalent)
(b)Primer2
Ounce
BMS 10-11, Type I
(b)Sealant4
Ounce
BMS 5-95 Type I or II,
Class B-1/2 or B-2.
(c) (d)Rivet116NAS1738E6-2
(c) (d)Rivet76NAS1738E6-3
(c) (d)Rivet40NAS1738E6-4
(e)Rivet (Countersink Re-
pair Washer)
76BACR15GF6D( )
(a) Fabricate from 2024-T3 clad sheet, 0.032 inch thick in accordance with Figure 8.
(b) See the Qualified Products List at the end of the Boeing Material Specification (BMS)
for supplier data.
(c) Refer to 737 Structural Repair Manual Chapter 51 for alternative fasteners.
(d) Rivet length determined on installation. Longer rivets may be required depending on
specific location. More rivet quantities may be required depending on specific location.
(e) Use these rivets to make the countersink repair washers. Any length rivet can be
used to make a countersink repair washer.
NOTE: The parts listed below are an estimate of the materials needed to accomplish a typical
permanent repair (Time-Limited Replacement) in accordance with Figure 9 at a single
location. Fastener quantity and grip length may vary depending on the specific location
of the repair.
Permanent Repair (Time-Limited Replacement)
NotesNameQTYPart Number / Specifica-
tion
(a) approximate size 22 x
12 inches.
Doubler1A
(a) approximate size 22 x
10 inches.
Tripler1B
(a) approximate size 24 x 3
inches.
Filler1C
(a) approximate size 24 x 4
inches.
Filler1D
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 02, 2007
737-53A1232Revision 3: July 27, 2015
31 of 161
BOEING SERVICE BULLETIN 737-53A1232
ALERTALERT

### Page 32

Permanent Repair (Time-Limited Replacement)
NotesNameQTYPart Number / Specifica-
tion
Chemical Conversion
Coating
2
Ounce
Alodine 1200S Type I,
Class A (or equivalent)
(b)Primer2
Ounce
BMS 10-11, Type I
(b)Sealant4
Ounce
BMS 5-95 Type I or II,
Class B-1/2 or B-2.
(c) (d)Rivet116BACR15FT7D5
(c) (d)Rivet20BACR15FT7D6
(c) (d)Rivet76BACR15FT7D7
(c) (d)Rivet20BACR15FT7D8
(e)Rivet (Countersink Re-
pair Washer)
76BACR15GF6D( )
(a) Fabricate from 2024-T3 clad sheet, 0.032 inch thick in accordance with Figure 9.
(b) See the Qualified Products List at the end of the Boeing Material Specification (BMS)
for supplier data.
(c) Refer to 737 Structural Repair Manual Chapter 51 for alternative fasteners.
(d) Rivet length determined on installation. Longer rivets may be required depending on
specific location. More rivet quantities may be required depending on specific location.
(e) Use these rivets to make the countersink repair washers. Any length rivet can be used
to make a countersink repair washer.
NOTE: The parts listed below are estimate of the materials needed to accomplish a typical
preventative modification in accordance with Figures 11, 12, 13, 14, 15 and 16 at a single
location. Fastener grip length may vary depending on the specific location of the
modification.
After 225,000 pressurization cycles of a fuselage fatigue test on a 737-800, a total of 56
cracks were found at different locations.
The maximum number of preventative modification locations affected by this bulletin is
102 for Group 1, 122 for Group 2, 104 for Group 3, 144 for Group 4, 168 for Group 5 and
83 for Group 6.
Preventative Modification
NotesNameQTYPart Number / Specifica-
tion
(a) 0.063 inch thick. Approx-
imate size 9 x 4 inches.
Doubler A1A
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 02, 2007
737-53A1232Revision 3: July 27, 2015
32 of 161
BOEING SERVICE BULLETIN 737-53A1232
ALERTALERT

### Page 33

Preventative Modification
NotesNameQTYPart Number / Specifica-
tion
(a) 0.032 inch thick at S-4.
Approximate size 9 x 4
inches.
Filler B1B
(a) 0.050 inch thick at S-7L.
Approximate size 9 x 4
inches.
(a) 0.040 inch thick at S-10.
Approximate size 9 x 4
inches.
(a) 0.032 inch thick. Approx-
imate size 11 x 5 inches.
Filler C1C
(a) 0.020 inch thick. Approx-
imate size 9 x 6 inches.
Filler D1D
Chemical Conversion
Coating
1
Ounce
Alodine 1200S Type I,
Class A (or equivalent)
(b)Primer2
Ounce
BMS 10-11, Type I
(b)Sealant4
Ounce
BMS 5-95 Type I or II,
Class B-1/2 or B-2.
(c) (d)Rivet24BACR15FT6D5
(c) (d)Rivet24BACR15FT6D6
(c) (d) (e)Rivet8BACR15DS7D7
(a) Fabricate from 2024-T3 clad sheet in accordance with Figures 11, 12, 13, 14, 15 and
16.
(b) See the Qualified Products List at the end of the Boeing Material Specification (BMS)
for supplier data.
(c) Refer to 737 Structural Repair Manual Chapter 51 for alternative fasteners.
(d) Rivet length determined on installation. Longer rivets may be required depending on
specific location. More rivet quantities may be required depending on specific location.
(e) To be used if oversize fastener is necessary.
3. Parts Modified and Reidentified:
None.
4. Parts Removed and Not Replaced:
None.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 02, 2007
737-53A1232Revision 3: July 27, 2015
33 of 161
BOEING SERVICE BULLETIN 737-53A1232
ALERTALERT

### Page 34

D. Parts Necessary to Change Spares
None.
E. Special Tooling - Price and Availability
None.
F. Special Tooling Necessary to do this Service Bulletin
No special tools or equipment are necessary to do the change in this service bulletin. But, maintenance
and overhaul tools in the manuals given in Paragraph 1.J., References, can be necessary. Examine
operator tool supply to make sure all necessary tools are available.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 02, 2007
737-53A1232Revision 3: July 27, 2015
34 of 161
BOEING SERVICE BULLETIN 737-53A1232
ALERTALERT

### Page 35

3.    ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL INFORMATION
CAUTION: KEEP THE WORK AREA, WIRES AND ELECTRICAL BUNDLES CLEAN OF METAL
PARTICLES OR CONTAMINATION WHEN YOU USE TOOLS. UNWANTED MATERIAL,
METAL PARTICLES OR CONTAMINATION CAUGHT IN WIRE BUNDLES CAN CAUSE
DAMAGE TO THE BUNDLES. DAMAGED WIRE BUNDLES CAN CAUSE SPARKS OR
OTHER ELECTRICAL DAMAGE.
NOTE: 1. Manual titles are referred to by acronyms. Refer to Paragraph 1.J., References, for
definition of the acronyms.
2. Obey all of the warnings and cautions given in the specified manual sections.
3. Unless shown differently, these dimensions and tolerances are used:
– Linear dimensions are in inches
– Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus
or minus 0.03 inch
– Tolerance on rivet and bolt edge margin is plus or minus 0.05 inch
– Angular tolerance is plus or minus 2 degrees
– Hole dimensions for standard solid rivets and fasteners are in Structural Repair
Manual (SRM) Chapter 51
– Torque Values:
— Values for structural fasteners are given in 737 Structural Repair Manual,
Chapter 51.
4. Use the approved fastener, process and material substitutions in accordance with
SRM Chapter 51.
5. If the length of any fastener specified in this service bulletin does not meet installation
standards given in SRM Chapter 51, then a fastener of the same specification, or
an approved substitute, with a length which meets the installation standards given
in SRM Chapter 51 may be used. In addition, washers may be installed for fastener
grip length in accordance with SRM Chapter 51. Refer to SOPM 20-50-01 for alternate
full threaded fasteners (screws) needed for installation in this service bulletin.
6. A Detailed Inspection is defined as: An intensive examination of a specific item,
installation, or assembly to detect damage, failure, or irregularity. Available lighting
is normally supplemented with a direct source of good lighting at an intensity deemed
appropriate. Inspection aids such as mirrors, magnifying lenses, etc. may be
necessary. Surface cleaning and elaborate procedures may be required.
7. These work instructions refer to procedures included in other Boeing documents.
When the words "refer to" are used and the operator has an accepted alternative
procedure, the accepted alternative procedure can be used. When the words "in
accordance with" are included in the instruction, the procedure in the Boeing document
must be used.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 02, 2007
737-53A1232Revision 3: July 27, 2015
35 of 161
BOEING SERVICE BULLETIN 737-53A1232
ALERTALERT

### Page 36

8. Boeing Service Letter 737-SL-51-042, Damage Reporting and Repair Plan/Design
Guidelines, is an acceptable procedure to request information from Boeing for
additional structural repair instructions. The Service Letter describes what information
must be provided to Boeing before a structural repair can be provided.
9. If it is necessary to remove more parts for access, you can remove those parts. If
you can get access without removing identified parts, it is not necessary to remove
all of the identified parts. Jacking and shoring limitations must be observed.
10. Where the work instructions include installation of a kept part, a new or serviceable
part with the same part number can be installed as an alternative to the kept part.
11. The compliance times for the actions in Paragraph 3.B., WORK INSTRUCTIONS
are in Paragraph 1.E., Compliance.
B. WORK INSTRUCTIONS
1. PART I: INSPECTION
a. Group 1:
Do an external detailed inspection and an external Non Destructive Inspection (NDI) for any
crack in the fuselage skin at chem-milled steps in accordance with FIGURE 1, at the intervals
in accordance with Paragraph 1.E., Compliance, Table 1, using one of the following options:
– Option 1: Do an external Medium Frequency Eddy Current (MFEC) or Magneto Optic
Imager (MOI) or C-Scan inspection.
NOTE: MOI and C-Scan inspections cannot be used within 4 inches of an existing repair
doubler edge. Within 4 inches of an existing repair doubler edge, the MFEC or
Ultrasonic Phased Array (UTPA) inspection must be used.
– Option 2: Do an external UTPA.
(1) If any crack is found, do one of the options that follow:
(a) Permanent repair: Do Part 2, Part 3 and Part 6.
(b) Time limited repair: Do Part 2, Part 4 and Part 6.
(2) If no crack is found, do one of the options that follow:
(a) Preventative modification: Do Part 2, Part 5 and Part 6.
NOTE: New installation of the preventative modification is limited to airplanes with
30,000 total flight cycles or less. For airplanes which have incorporated
Boeing Business Jet Lower Cabin Altitude Supplemental Type Certificate
ST01697SE, new installation of the preventative modification is limited to
airplanes with 15,000 total flight cycles or less.
(b) Repeat inspections: Do the repeat Inspections in accordance with FIGURE 1, at the
intervals in accordance with Paragraph 1.E., Compliance, Table 1.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 02, 2007
737-53A1232Revision 3: July 27, 2015
36 of 161
BOEING SERVICE BULLETIN 737-53A1232
ALERTALERT

### Page 37

b. Group 2:
Do an external detailed inspection and an external Non Destructive Inspection (NDI) for any
crack in the fuselage skin at chem-milled steps in accordance with FIGURE 2, at the intervals
in accordance with Paragraph 1.E., Compliance, Table 1, using one of the following options:
– Option 1: Do an external Medium Frequency Eddy Current (MFEC) or Magneto Optic
Imager (MOI) or C-Scan inspection.
NOTE: MOI and C-Scan inspections cannot be used within 4 inches of an existing repair
doubler edge. Within 4 inches of an existing repair doubler edge, the MFEC or
Ultrasonic Phased Array (UTPA) inspection must be used.
– Option 2: Do an external UTPA.
(1) If any crack is found, do one of the options that follow:
(a) Permanent repair: Do Part 2, Part 3 and Part 6.
(b) Time limited repair: Do Part 2, Part 4 and Part 6.
(2) If no crack is found, do one of the options that follow:
(a) Preventative modification: Do Part 2, Part 5 and Part 6.
NOTE: New installation of the preventative modification is limited to airplanes with
30,000 total flight cycles or less. For airplanes which have incorporated
Boeing Business Jet Lower Cabin Altitude Supplemental Type Certificate
ST01697SE, new installation of the preventative modification is limited to
airplanes with 15,000 total flight cycles or less.
(b) Repeat inspections: Do the repeat Inspections in accordance with FIGURE 2, at the
intervals in accordance with Paragraph 1.E., Compliance, Table 1
c. Group 3:
Do an external detailed inspection and an external Non Destructive Inspection (NDI) for any
crack in the fuselage skin at chem-milled steps in accordance with FIGURE 3, at the intervals
in accordance with Paragraph 1.E., Compliance, Table 1, using one of the following options:
– Option 1: Do an external Medium Frequency Eddy Current (MFEC) or Magneto Optic
Imager (MOI) or C-Scan inspection.
NOTE: MOI and C-Scan inspections cannot be used within 4 inches of an existing repair
doubler edge. Within 4 inches of an existing repair doubler edge, the MFEC or
Ultrasonic Phased Array (UTPA) inspection must be used.
– Option 2: Do an external UTPA.
(1) If any crack is found, do one of the options that follow:
(a) Permanent repair: Do Part 2, Part 3 and Part 6.
(b) Time limited repair: Do Part 2, Part 4 and Part 6.
(2) If no crack is found, do one of the options that follow:
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 02, 2007
737-53A1232Revision 3: July 27, 2015
37 of 161
BOEING SERVICE BULLETIN 737-53A1232
ALERTALERT

### Page 38

(a) Preventative modification: Do Part 2, Part 5 and Part 6.
NOTE: New installation of the preventative modification is limited to airplanes with
30,000 total flight cycles or less. For airplanes which have incorporated
Boeing Business Jet Lower Cabin Altitude Supplemental Type Certificate
ST01697SE, new installation of the preventative modification is limited to
airplanes with 15,000 total flight cycles or less.
(b) Repeat inspections: Do the repeat Inspections in accordance with FIGURE 3, at the
intervals in accordance with Paragraph 1.E., Compliance, Table 1
d. Group 4:
Do an external detailed inspection and an external Non Destructive Inspection (NDI) for any
crack in the fuselage skin at chem-milled steps in accordance with FIGURE 4, at the intervals
in accordance with Paragraph 1.E., Compliance, Table 1, using one of the following options:
– Option 1: Do an external Medium Frequency Eddy Current (MFEC) or Magneto Optic
Imager (MOI) or C-Scan inspection.
NOTE: MOI and C-Scan inspections cannot be used within 4 inches of an existing repair
doubler edge. Within 4 inches of an existing repair doubler edge, the MFEC or
Ultrasonic Phased Array (UTPA) inspection must be used.
– Option 2: Do an external UTPA.
(1) If any crack is found, do one of the options that follow:
(a) Permanent repair: Do Part 2, Part 3 and Part 6.
(b) Time limited repair: Do Part 2, Part 4 and Part 6.
(2) If no crack is found, do one of the options that follow:
(a) Preventative modification: Do Part 2, Part 5 and Part 6.
NOTE: New installation of the preventative modification is limited to airplanes with
30,000 total flight cycles or less. For airplanes which have incorporated
Boeing Business Jet Lower Cabin Altitude Supplemental Type Certificate
ST01697SE, new installation of the preventative modification is limited to
airplanes with 15,000 total flight cycles or less.
(b) Repeat inspections: Do the repeat Inspections in accordance with FIGURE 4, at the
intervals in accordance with Paragraph 1.E., Compliance, Table 1
e. Group 5:
Do an external detailed inspection and an external Non Destructive Inspection (NDI) for any
crack in the fuselage skin at chem-milled steps in accordance with FIGURE 5, at the intervals
in accordance with Paragraph 1.E., Compliance, Table 1, using one of the following options:
– Option 1: Do an external Medium Frequency Eddy Current (MFEC) or Magneto Optic
Imager (MOI) or C-Scan inspection.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 02, 2007
737-53A1232Revision 3: July 27, 2015
38 of 161
BOEING SERVICE BULLETIN 737-53A1232
ALERTALERT

### Page 39

NOTE: MOI and C-Scan inspections cannot be used within 4 inches of an existing repair
doubler edge. Within 4 inches of an existing repair doubler edge, the MFEC or
Ultrasonic Phased Array (UTPA) inspection must be used.
– Option 2: Do an external UTPA.
(1) If any crack is found, do one of the options that follow:
(a) Permanent repair: Do Part 2, Part 3 and Part 6.
(b) Time limited repair: Do Part 2, Part 4 and Part 6.
(2) If no crack is found, do one of the options that follow:
(a) Preventative modification: Do Part 2, Part 5 and Part 6.
NOTE: New installation of the preventative modification is limited to airplanes with
30,000 total flight cycles or less. For airplanes which have incorporated
Boeing Business Jet Lower Cabin Altitude Supplemental Type Certificate
ST01697SE, new installation of the preventative modification is limited to
airplanes with 15,000 total flight cycles or less.
(b) Repeat inspections: Do the repeat Inspections in accordance with FIGURE 5, at the
intervals in accordance with Paragraph 1.E., Compliance, Table 1
f. Group 6:
Do an external detailed inspection and an external Non Destructive Inspection (NDI) for any
crack in the fuselage skin at chem-milled steps in accordance with FIGURE 6, at the intervals
in accordance with Paragraph 1.E., Compliance, Table 1, using one of the following options:
– Option 1: Do an external Medium Frequency Eddy Current (MFEC) or Magneto Optic
Imager (MOI) or C-Scan inspection.
NOTE: MOI and C-Scan inspections cannot be used within 4 inches of an existing repair
doubler edge. Within 4 inches of an existing repair doubler edge, the MFEC or
Ultrasonic Phased Array (UTPA) inspection must be used.
– Option 2: Do an external UTPA.
(1) If any crack is found, do one of the options that follow:
(a) Permanent repair: Do Part 2, Part 3 and Part 6.
(b) Time limited repair: Do Part 2, Part 4 and Part 6.
(2) If no crack is found, do one of the options that follow:
(a) Preventative modification: Do Part 2, Part 5 and Part 6.
NOTE: New installation of the preventative modification is limited to airplanes with
30,000 total flight cycles or less. For airplanes which have incorporated
Boeing Business Jet Lower Cabin Altitude Supplemental Type Certificate
ST01697SE, new installation of the preventative modification is limited to
airplanes with 15,000 total flight cycles or less.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 02, 2007
737-53A1232Revision 3: July 27, 2015
39 of 161
BOEING SERVICE BULLETIN 737-53A1232
ALERTALERT

### Page 40

(b) Repeat inspections: Do the repeat Inspections in accordance with Figure 6, at the
intervals in accordance with Paragraph 1.E., Compliance, Table 1.
2. PART II: ACCESS
a. Get internal access to the passenger cabin for the area of the skin modification or repair.
(1) Remove passenger seats where necessary. Refer to 737-600/700/800/900 AMM 25-22-00
as an accepted procedure.
(2) Remove sidewall linings where necessary. Refer to 737-600/700/800/900 AMM 25-21-46
as an accepted procedure.
(3) Remove sidewall insulation where necessary. Refer to 737-600/700/800/900 AMM
25-80-00 as an accepted procedure.
(4) Remove passenger service units where necessary. Refer to 737-600/700/800/900 AMM
25-23-61 as an accepted procedure.
(5) Remove overhead stowage bins where necessary. Refer to 737-600/700/800/900 AMM
25-24-31 as an accepted procedure.
(6) Remove ceiling panels where necessary. Refer to 737-600/700/800/900 AMM 25-21-45
as an accepted procedure.
3. PART III: PERMANENT REPAIR
a. Install the permanent repair in accordance with Figure 7.
b. At the intervals in accordance with Paragraph 1.E., Compliance, Table 2, do the Eddy Current
Inspections and Detailed Inspection in accordance with Figure 10.
(1) If any crack is found, contact The Boeing Company for work instructions and do the work.
(2) Replace any loose or missing fastener.
4. PART IV: TIME LIMITED REPAIR
a. Install the time limited repair in accordance with Figure 8.
b. Do an Internal and External Detailed Inspection of the repair area for any crack and loose or
missing fasteners, at the intervals in accordance with Paragraph 1.E., Compliance, Table 3.
(1) Replace any loose or missing fastener.
(2) If any crack is found, remove the time limited repair and install the permanent repair (time
limited repair replacement) in accordance with Figure 9.
c. Remove the time limited repair and install the permanent repair (time limited repair replacement)
in accordance with Figure 9, at the time specified in Paragraph 1.E., Compliance, Table 3.
Accomplish inspections per paragraph 3.B.3.b., after permanent repair is installed.
5. PART V: PREVENTATIVE MODIFICATION
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 02, 2007
737-53A1232Revision 3: July 27, 2015
40 of 161
BOEING SERVICE BULLETIN 737-53A1232
ALERTALERT

### Page 41

NOTE: Install the preventative modification prior to 30,000 total flight cycles to prevent Widespread
Fatigue Damage (WFD) before the airplane reaches its limit of validity (LOV).
a. Group 1-5:
Install the preventative modification at S-4 and S-10 locations in accordance with the Figures
in the table below:
FigureGroup
FIGURE 11Group 1
FIGURE 12Group 2
FIGURE 13Group 3
FIGURE 14Group 4
FIGURE 15Group 5
b. Group 6:
Install the preventative modification at S-4, S-7L and S-10 locations in accordance with FIGURE
16.
6. PART VI: CLOSE ACCESS
a. Install all passenger cabin equipment removed for access.
(1) Install ceiling panels where necessary. Refer to 737-600/700/800/900 AMM 25-21-45 as
an accepted procedure.
(2) Install overhead stowage bins where necessary. Refer to 737-600/700/800/900 AMM
25-24-31 as an accepted procedure.
(3) Install passenger service units where necessary. Refer to 737-600/700/800/900 AMM
25-23-61 as an accepted procedure.
(4) Install sidewall insulation where necessary. Refer to 737-600/700/800/900 AMM 25-80-00
as an accepted procedure.
(5) Install sidewall linings where necessary. Refer to 737-600/700/800/900 AMM 25-21-46
as an accepted procedure.
(6) Install passenger seats where necessary. Refer to 737-600/700/800/900 AMM 25-22-00
as an accepted procedure.
b. Put the airplane back to a serviceable condition.
7. PART 7: POST PREVENTATIVE MODIFICATION INSPECTION
a. For airplanes with preventative modifications installed at or before 30,000 total flight cycles,
do the following:
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 02, 2007
737-53A1232Revision 3: July 27, 2015
41 of 161
BOEING SERVICE BULLETIN 737-53A1232
ALERTALERT

### Page 42

(1) Do the External Detailed Inspection and the External High Frequency Eddy Current
(HFEC) Inspection in accordance with Figure 17, at the intervals in accordance with
Paragraph 1.E., Compliance, Table 1b.
(a) If any crack is found, contact The Boeing Company for work instructions and do the
work.
(b) Replace any loose or missing fastener in accordance with PART V: PREVENTATIVE
MODIFICATION.
(2) Do an external NDI for any crack in the fuselage skin at the chem-milled step using a
MFEC inspection in accordance with FIGURE 18, at the intervals in accordance with
Paragraph 1.E., Compliance, Table 1a.
(a) If any crack is found, contact The Boeing Company for work instructions and do the
work.
b. For airplanes with preventative modifications installed after 30,000 total flight cycles, do the
following:
(1) Do the External Detailed Inspection and the External High Frequency Eddy Current
(HFEC) Inspection in accordance with Figure 17, at the intervals in accordance with
Paragraph 1.E., Compliance, Table 1b.
(a) If any crack is found, contact The Boeing Company for work instructions and do the
work.
(b) Replace any loose or missing fastener in accordance with PART V: PREVENTATIVE
MODIFICATION.
(2) Do an external NDI for any crack in the fuselage skin at the chem-milled step using a
MFEC inspection in accordance with FIGURE 18, at the intervals in accordance with
Paragraph 1.E., Compliance, Table 1a.
(a) If any crack is found, contact The Boeing Company for work instructions and do the
work.
(3) Contact The Boeing Company for work instructions and do the work.
NOTE: Airplanes listed in APPENDIX A have been evaluated by The Boeing Company
for the preventative modifications installed at the listed flight cycles. These
airplanes are not required to contact The Boeing Company for work instructions
only for the preventative modifications installed at the listed flight cycles.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 02, 2007
737-53A1232Revision 3: July 27, 2015
42 of 161
BOEING SERVICE BULLETIN 737-53A1232
ALERTALERT

### Page 43 (OCR)

BOEING SERVICE BULLETIN 737-53A1232
ALERT  ALERT
This Figure applies only to: Group 1.
STA
540
S-4R
BL S-4L
STA
360
S-10L
10000000  OL-
SEE A  FOR TYPICAL
INSPECTION AREA
AT S-4 AND S-10
LOCATIONS
STA
887
_ S-4R
/ 0  BL  → S-4L
STA
727  S-10L
STA  900000
540
FWD C
LEFT SIDE SHOWN
737-600
FIGURE 1: CHEM-MILLED STEP - INSPECTION
(SHEET 1 OF 4)
Original Issue: April 02, 2007
Revision 3 July 27, 2015  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  Work - See page 1 for details.  737-53A1232  43 of 161

### Page 44 (OCR)

BOEING SERVICE BULLETIN 737-53A1232
ALERT  ALERT
STA
540
S-4L
BL
S-4R 0\
STA
360
S-10R
0000
SEE
FOR TYPICAL
INSPECTION AREA AT
S-4 AND S-10
STA  LOCATIONS
S-4L  887
S-4R  BL
STA
S-10R  727
00008  STA
2000000r  540  300
FWD
RIGHT SIDE SHOWN
737-600  481100
FIGURE 1: CHEM-MILLED STEP - INSPECTION
(SHEET 2 OF 4)
Original Issue: April 02, 2007
Revision 3 July 27, 2015  Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright @ Unpublished  737-53A1232
Work - See page 1 for details.  44 of 161

### Page 45 (OCR)

BOEING SERVICE BULLETIN 737-53A1232
ALERT  ALERT
FRAME  TYPICAL  FRAME
UPPER  C/L  CRACK  C/L
SKIN
S-4
S-10
(TYPICAL)
- C/L
LOWER
SKIN
TYPICAL INSPECTION AREA
- UPPER
SKIN
TYPICAL
INSPECTION AREA  CRACK
LOWER  STRINGER
SKIN
- INBD
A-A
480564
FIGURE 1: CHEM-MILLED STEP - INSPECTION
(SHEET 3 OF 4)
Original Issue: April 02, 2007
Revision 3 July 27, 2015  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  737-53A1232
Work - See page 1 for details.  45 of 161

### Page 46

The step numbers shown below agree with the numbers shown in the circle symbols in the figure.
MORE DATAIDENTIFICATIONNAMETASKSTEP
(a)-SkinInspect1
(b)-SkinInspect2
(a) Do an external Non Destructive Inspection (NDI) for any crack at the chem-milled
step using Option 1 or Option 2:
Option 1:
– Medium Frequency Eddy Current (MFEC) in accordance with 737 NDT Part
6, 53-30-09, or 737 NDT Part 6, 53-30-18 or 737 NDT Part 6, 53-30-23 or
– Magneto Optic Imager (MOI) in accordance with 737 NDT Part 6, 53-30-19
or
– C-Scan in accordance with 737 NDT Part 6, 53-30-25
Option 2:
– Ultrasonic Phased Array (UTPA) in accordance with 737 NDT Part 4, 53-30-
07
(b) Do an external Detailed Inspection for any crack in the fuselage skin along the
chem-milled steps at the specified locations.
FIGURE 1: CHEM-MILLED STEP - INSPECTION
(SHEET 4 OF 4)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 02, 2007
737-53A1232Revision 3 July 27, 2015
46 of 161
BOEING SERVICE BULLETIN 737-53A1232
ALERTALERT

### Page 47 (OCR)

BOEING SERVICE BULLETIN 737-53A1232
ALERT  ALERT
This Figure applies only to: Group 2.
STA
540
S-4R
BL S-4L
STA
360  S-10L
10000000000
SEE  FOR TYPICAL
INSPECTION AREA
AT S-4 AND S-10
LOCATIONS
STA
887  _ S-4R
BL
S-4L
STA  S-10L
727
STA  000000
540
FWD S
LEFT SIDE SHOWN
737-700
FIGURE 2: CHEM-MILLED STEP - INSPECTION
(SHEET 1 OF 4)
Original Issue: April 02, 2007
Revision 3 July 27, 2015  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  737-53A1232
Work - See page 1 for details.  47 of 161

### Page 48 (OCR)

BOEING SERVICE BULLETIN 737-53A1232
ALERT  ALERT
STA
540
S-4L
BL
S-4R -
STA
S-10R  360
000  000000
SEE  FOR TYPICAL
STA  INSPECTION AREA
AT S-4 AND  S-10
S-4L  887  LOCATIONS
S-4R  BL
S-10R  STA
727
0000  STA
540
0 0  000  J00
FWD
RIGHT SIDE SHOWN
737-700  480336
FIGURE 2: CHEM-MILLED STEP - INSPECTION
(SHEET 2 OF 4)
Original Issue: April 02, 2007
Revision 3 July 27, 2015  Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright © Unpublished  ZEZIES-LEL
Work - See page 1 for details.  1911O 80

### Page 49 (OCR)

BOEING SERVICE BULLETIN 737-53A1232
ALERT  ALERT
FRAME  TYPICAL  FRAME
UPPER  C/L  CRACK  C/L
SKIN
S-4
S-10
(TYPICAL)
- c/L
LOWER
SKIN
TYPICAL INSPECTION AREA
• UPPER
SKIN
TYPICAL
INSPECTION AREA  CRACK
LOWER  STRINGER
SKIN
- INBD
A-A
480563
FIGURE 2: CHEM-MILLED STEP - INSPECTION
(SHEET 3 OF 4)
Original Issue: April 02, 2007
Revision 3 July 27, 2015  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  737-53A1232
Work - See page 1 for details.  49 of 161

### Page 50

The step numbers shown below agree with the numbers shown in the circle symbols in the figure.
MORE DATAIDENTIFICATIONNAMETASKSTEP
(a)-SkinInspect1
(b)-SkinInspect2
(a) Do an external Non Destructive Inspection (NDI) for any crack at the chem-milled
step using Option 1 or Option 2:
Option 1:
– Medium Frequency Eddy Current (MFEC) in accordance with 737 NDT Part
6, 53-30-09 or 737 NDT Part 6, 53-30-18 or 737 NDT Part 6, 53-30-23 or
– Magneto Optic Imager (MOI) in accordance with 737 NDT Part 6, 53-30-19
or
– C-Scan in accordance with 737 NDT Part 6, 53-30-25
Option 2:
– Ultrasonic Phased Array (UTPA) in accordance with 737 NDT Part 4, 53-30-
07.
(b) Do an external Detailed Inspection for any crack in the fuselage skin along the
chem-milled steps at the specified locations.
FIGURE 2: CHEM-MILLED STEP - INSPECTION
(SHEET 4 OF 4)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 02, 2007
737-53A1232Revision 3 July 27, 2015
50 of 161
BOEING SERVICE BULLETIN 737-53A1232
ALERTALERT

### Page 51 (OCR)

BOEING SERVICE BULLETIN 737-53A1232
ALERT  ALERT
This Figure applies only to: Group 3.
STA
540
S-4R
Л/%  BL S-4L
STA
360  S-10L
10000000000  FOR TYPICAL
INSPECTION AREA
SEE  AT S-4 AND S-10
LOCATIONS
STA
887
_ S-4R
BL  S-4L
/ 0
S-10L
000  08000001
FWD C
LEFT SIDE SHOWN
737-700
INCREASED GROSS WEIGHT
FIGURE 3: CHEM-MILLED STEP - INSPECTION
(SHEET 1 OF 4)
Original Issue: April 02, 2007
Revision 3 July 27, 2015  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  737-53A1232
Work - See page 1 for details.  51 of 161

### Page 52 (OCR)

BOEING SERVICE BULLETIN 737-53A1232
ALERT  ALERT
STA
S-4L
BL
S-4R 0>
STA
S-10R  360
0000000000
SEE  A  FOR TYPICAL
INSPECTION AREA
STA
AT S-4 AND S-10
S-4L  887  LOCATIONS
S-4R  BL
S-10R  STA
727
0000  000
000000
FWD
RIGHT SIDE SHOWN
737-700  480577
INCREASED GROSS WEIGHT
FIGURE 3: CHEM-MILLED STEP - INSPECTION
(SHEET 2 OF 4)
Original Issue: April 02, 2007
Revision 3 July 27, 2015  Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright @ Unpublished  737-53A1232
Work - See page 1 for details.  52 of 161

### Page 53 (OCR)

BOEING SERVICE BULLETIN 737-53A1232
ALERT  ALERT
FRAME  TYPICAL  FRAME
UPPER  C/L  CRACK  C/L
SKIN
S-4
S-10
(TYPICAL)
- C/L
LOWER
SKIN
TYPICAL INSPECTION AREA
• UPPER
SKIN
TYPICAL
INSPECTION AREA  CRACK
LOWER  STRINGER
SKIN
- INBD
A-A
480565
FIGURE 3: CHEM-MILLED STEP - INSPECTION
(SHEET 3 OF 4)
Original Issue: April 02, 2007
Revision 3 July 27, 2015  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  737-53A1232
Work - See page 1 for details.  53 of 161

### Page 54

The step numbers shown below agree with the numbers shown in the circle symbols in the figure.
MORE DATAIDENTIFICATIONNAMETASKSTEP
(a)-SkinInspect1
(b)-SkinInspect2
(a) Do an external Non Destructive Inspection (NDI) for any crack at the chem-milled
step using Option 1 or Option 2:
Option 1:
– Medium Frequency Eddy Current (MFEC) in accordance with 737 NDT Part
6, 53-30-09 or 737 NDT Part 6, 53-30-18 or 737 NDT Part 6, 53-30-23 or
– Magneto Optic Imager (MOI) in accordance with 737 NDT Part 6, 53-30-19
or
– C-Scan in accordance with 737 NDT Part 6, 53-30-25
Option 2:
– Ultrasonic Phased Array (UTPA) in accordance with 737 NDT Part 4, 53-30-
07
(b) Do an external Detailed Inspection for any crack in the fuselage skin along the
chem-milled steps at the specified locations.
FIGURE 3: CHEM-MILLED STEP - INSPECTION
(SHEET 4 OF 4)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 02, 2007
737-53A1232Revision 3 July 27, 2015
54 of 161
BOEING SERVICE BULLETIN 737-53A1232
ALERTALERT

### Page 55 (OCR)

BOEING SERVICE BULLETIN 737-53A1232
ALERT  ALERT
This Figure applies only to: Group 4.
STA
540
S-4R
BL S-4L
_ S-10L
STA
360  0000000000000000  FOR TYPICAL INSPECTION AREA
SEE  A AT S-4 AND S-10 LOCATIONS
STA
887
_ S-4R
BL  • S-4L
/ 0
_ S-10L
0000
00.
0000
FWD S
LEFT SIDE SHOWN  737-800  481410
FIGURE 4: CHEM-MILLED STEP - INSPECTION
(SHEET 1 OF 4)
Original Issue: April 02, 2007
Revision 3 July 27, 2015  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  737-53A1232
Work - See page 1 for details.  55 of 161

### Page 56 (OCR)

BOEING SERVICE BULLETIN 737-53A1232
ALERT  ALERT
STA
540
S-4L
BL
S-4R _
S-10R
STA
360
00000090000000  SEE
STA  FOR TYPICAL
887  INSPECTION AREA
AT S-4 AND  S-10
•4R  BL  LOCATIONS
S-10R
0800000800  STA
727
• FWD
RIGHT SIDE SHOWN  737-800  481102
FIGURE 4: CHEM-MILLED STEP - INSPECTION
(SHEET 2 OF 4)
Original Issue: April 02, 2007
Revision 3 July 27, 2015  Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright © Unpublished  ZEZIES-LEL
Work - See page 1 for details.  56 of 161

### Page 57 (OCR)

BOEING SERVICE BULLETIN 737-53A1232
ALERT  ALERT
FRAME  TYPICAL  FRAME
UPPER  C/L  CRACK  C/L
SKIN
S-4
S-10
(TYPICAL)
- C/L
LOWER
SKIN
TYPICAL INSPECTION AREA
• UPPER
SKIN
TYPICAL
INSPECTION AREA  CRACK
LOWER  STRINGER
SKIN
- INBD
A-A
480566
FIGURE 4: CHEM-MILLED STEP - INSPECTION
(SHEET 3 OF 4)
Original Issue: April 02, 2007
Revision 3 July 27, 2015  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  737-53A1232
Work - See page 1 for details.  57 of 161

### Page 58

The step numbers shown below agree with the numbers shown in the circle symbols in the figure.
MORE DATAIDENTIFICATIONNAMETASKSTEP
(a)-SkinInspect1
(b)-SkinInspect2
(a) Do an external Non Destructive Inspection (NDI) for any crack at the chem-milled
step using Option 1 or Option 2:
Option 1:
– Medium Frequency Eddy Current (MFEC) in accordance with 737 NDT Part
6, 53-30-09 or 737 NDT Part 6, 53-30-18 or 737 NDT Part 6, 53-30-23 or
– Magneto Optic Imager (MOI) in accordance with 737 NDT Part 6, 53-30-19
or
– C-Scan in accordance with 737 NDT Part 6, 53-30-25
Option 2:
– Ultrasonic Phased Array (UTPA) in accordance with 737 NDT Part 4, 53-30-
07
(b) Do an external Detailed Inspection for any crack in the fuselage skin along the
chem-milled steps at the specified locations.
FIGURE 4: CHEM-MILLED STEP - INSPECTION
(SHEET 4 OF 4)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 02, 2007
737-53A1232Revision 3 July 27, 2015
58 of 161
BOEING SERVICE BULLETIN 737-53A1232
ALERTALERT

### Page 59 (OCR)

BOEING SERVICE BULLETIN 737-53A1232
ALERT  ALERT
This Figure applies only to: Group 5.
STA
540  _ S-4R
BL S-4L
S-10L
C
STA  360  0000
FOR TYPICAL
INSPECTION AREA
SEE  AT S-4 AND S-10  LOCATIONS  STA  887  S-4R
- S-4L
STA  S-10L
7271
100
FWD C
LEFT SIDE SHOWN  737-900  481418
FIGURE 5: CHEM-MILLED STEP - INSPECTION
(SHEET 1 OF 4)
Original Issue: April 02, 2007
Revision 3 July 27, 2015  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  737-53A1232
Work - See page 1 for details.  59 of 161

### Page 60 (OCR)

BOEING SERVICE BULLETIN 737-53A1232
ALERT  ALERT
STA
S-4L.  540
S-4R  BL
S-10R
STA
360
000
STA
S-4L  887  SEE
S-4R  BL  FOR TYPICAL
INSPECTION AREA
AT S-4  AND  S-10
STA  LOCATIONS
S-10R  7271
00
000
000
* FWD
RIGHT SIDE SHOWN  737-900  481103
FIGURE 5: CHEM-MILLED STEP - INSPECTION
(SHEET 2 OF 4)
Original Issue: April 02, 2007
Revision 3 July 27, 2015  Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright @ Unpublished  737-53A1232
Work - See page 1 for details.  60 of 161

The text continues at https://openairdocs.org/service-documents/boeing/737-53a1232/file/153f5b692055.md?from=61

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
