# Boeing Alert Requirements Bulletin 737-53A1377 RB: No revision named

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2018-0272; AD 2018-17-23 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Alert Requirements Bulletin 737-53A1377 RB](https://openairdocs.org/service-documents/boeing/737-53a1377-rb.md)
- Title as filed: 737-53A1377 RB
- Pages: 18
- PDF: https://openairdocs.org/files/sha256/84/61/84619745f8254a4189e789bdd0c138f43d2be8c744dd353202249c243b9a63dd
- Page: https://openairdocs.org/service-documents/boeing/737-53a1377-rb/file/84619745f825

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Commercial 
Airplanes
737
Requirements Bulletin
ALERT
Number: 737-53A1377 RB
Original Issue: December 11, 2017
ATA System: 5311
SUBJECT: FUSELAGE - Frames - Inspection of Windshield No 3, Aft Sill Web at STA 254.6, Left
and Right Side.
Export of this technology is controlled under the United States Export Administration Regulations (EAR) (15
CFR 300-774). An export license may be required before it is used for development, production or use by foreign
persons from specific countries. The controller of this data has the individual responsibility to abide by all export
laws.
9E991ECCN:
Copyright © 2017 Boeing.
Unpublished Work. All Rights Reserved.
Treatment of this document and its content is governed by contract with Boeing. Rights to use this document
are licensed on a per aircraft basis and such rights may not be transferable. For more information, contact The
Boeing Company.
Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner,
BBJ, DC-8, DC-9, DC-10, KC-10, KC-46, KDC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8, Poseidon and
Boeing liveries are all trademarks owned by The Boeing Company; and no trademark license is granted in
connection with this document unless provided in writing by Boeing.
Original Issue: December 11, 2017
737-53A1377 RB
1 of 18
2.0

### Page 2

Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: December 11, 2017
737-53A1377 RB
2 of 18
REQUIREMENTS BULLETIN 737-53A1377
ALERTALERT
BLANK PAGE

### Page 3

Table of Contents
1. EFFECTIVITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
A. Airplanes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
B. Spares Affected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2. CONCURRENT REQUIREMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3. COMPLIANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
4. APPROVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
5. ACCOMPLISHMENT INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
A. General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
B. Work Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
FIGURE 3: HIGH FREQUENCY EDDY CURRENT (HFEC) INSPECTION OF THE WINDSHIELD NO 3,
AFT SILL WEB AT STA 254.6, LEFT SIDE  [Group 2] . . . . . . . . . . . . . . . . . . . . 13
FIGURE 4: HIGH FREQUENCY EDDY CURRENT (HFEC) INSPECTION OF THE WINDSHIELD NO 3,
AFT SILL WEB AT STA 254.6, RIGHT SIDE  [Group 2] . . . . . . . . . . . . . . . . . . . 16
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: December 11, 2017
737-53A1377 RB
3 of 18
REQUIREMENTS BULLETIN 737-53A1377
ALERTALERT

### Page 4

Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: December 11, 2017
737-53A1377 RB
4 of 18
REQUIREMENTS BULLETIN 737-53A1377
ALERTALERT
BLANK PAGE

### Page 5

Commercial 
Airplanes
737
Requirements Bulletin
ALERT
Number: 737-53A1377 RB
Original Issue: December 11, 2017
ATA System: 5311
SUBJECT: FUSELAGE - Frames - Inspection of Windshield No 3, Aft Sill Web at STA 254.6, Left
and Right Side.
THIS DOCUMENT IS SENT TO THE OPERATORS OF RECORD OF THE AIRPLANES SHOWN IN
PARAGRAPH 1.A., EFFECTIVITY. IF AN AIRPLANE HAS BEEN LEASED OR SOLD, SEND THIS DOCUMENT
TO THE NEW OPERATOR. IF APPLICABLE SPARES HAVE BEEN SOLD, SEND THIS DOCUMENT TO THE
NEW OWNER. THIS IS AN ENHANCED REQUIRED FOR COMPLIANCE DOCUMENT. THE BOEING
PROCESSES USED TO CREATE THE SERVICE BULLETIN (SB) AND THE REQUIREMENTS BULLETIN
(RB) ENSURE THAT THE INFORMATION BETWEEN "RC START" AND "RC END" IN THE SB ARE IDENTICAL
TO THE INFORMATION IN THE SAME SECTIONS (COMPLIANCE, WORK INSTRUCTIONS…) OF THE RB
WHICH THE SB REFERS TO AS THE RELATED DOCUMENT.
1. EFFECTIVITY
A. Airplanes
Service Bulletin 737-53A1377 and Requirements Bulletin 737-53A1377 RB are applicable to all
737-100/-200/-200C/-300/-400/-500 Airplanes, line numbers 1 through 3132 in 2 groups.
DESCRIPTIONCONFIGURATIONGROUP
737-100/-200/-200C airplanes. Line numbers 1-291.-1
737-200/-200C/-300/-400/-500 airplanes. Line numbers 292-3132.-2
B. Spares Affected
None.
2. CONCURRENT REQUIREMENTS
None.
3. COMPLIANCE
The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to
Requirements Bulletin 737-53A1377 RB. The Airworthiness Directive will make the compliance tasks and
times given in Requirements Bulletin 737-53A1377 RB mandatory.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: December 11, 2017
737-53A1377 RB
5 of 18

### Page 6

Accomplish the required action(s), based on the applicable conditions in Table 1 in accordance with the
Accomplishment Instructions.
When more than one OPTION is given for a CONDITION, do only one of the OPTION numbers. When
more than one ACTION is given for a CONDITION number or an OPTION number, do all of the ACTION
numbers for that CONDITION number or OPTION number.
Group 1:
The Boeing Company endorses the FAA rules related to Limit of Validity (LOV) and recommends immediate
and permanent removal from service of any airplanes upon reaching the LOV, whether or not it is operated
under FAA jurisdiction. As such, The Boeing Company no longer provides maintenance instructions for
airplanes that have accumulated flight cycles beyond the LOV. Airplanes in Group 1 (line number 1-291)
have accumulated flight cycles beyond the LOV of the maintenance program. 14 CFR 121.1115 and 129.115
prohibit operation of an airplane beyond its LOV.
Group 2:
Table 1: High Frequency Eddy Current (HFEC) Inspection of the Windshield No 3, Aft Sill Web at STA
254.6, Between S-9 and S-11 on the Left and Right Side, for Any Crack.
Repeat Interval
(Not to Exceed)
Compliance Time
(Whichever Occurs Later)
ActionCondition
-Within 6,000
flight cycles af-
ter the original
issue date of
Requirements
Bulletin 737-
53A1377 RB.
Before 24,000
total flight cy-
cles.
Do a HIGH FREQUENCY
EDDY CURRENT (HFEC)
INSPECTION OF THE
WINDSHIELD NO 3, AFT
SILL WEB AT STA 254.6,
BETWEEN S-9 AND S-11
ON THE LEFT AND RIGHT
SIDE for any crack.
All airplanes.
-Before further flight.Contact The Boeing Compa-
ny for repair instructions
and do the repair.
CONDITION 1:
ANY CRACK FOUND
ON THE LEFT SIDE.
24,000 flight cy-
cles.
-Repeat the HIGH FRE-
QUENCY EDDY CURRENT
(HFEC) INSPECTION OF
THE WINDSHIELD NO. 3,
AFT SILL WEB AT STA
254.6, BETWEEN S-9 AND
S-11 ON THE LEFT SIDE
for any crack.
CONDITION 2:
NO CRACK FOUND ON
THE LEFT SIDE.
-Before further flight.Contact The Boeing Compa-
ny for repair instructions
and do the repair.
CONDITION 3:
ANY CRACK FOUND
ON THE RIGHT SIDE.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: December 11, 2017
737-53A1377 RB
6 of 18
REQUIREMENTS BULLETIN 737-53A1377
ALERTALERT

### Page 7

Group 2:
Table 1: High Frequency Eddy Current (HFEC) Inspection of the Windshield No 3, Aft Sill Web at STA
254.6, Between S-9 and S-11 on the Left and Right Side, for Any Crack.
Repeat Interval
(Not to Exceed)
Compliance Time
(Whichever Occurs Later)
ActionCondition
24,000 flight cy-
cles.
-Repeat the HIGH FRE-
QUENCY EDDY CURRENT
(HFEC) INSPECTION OF
THE WINDSHIELD NO. 3,
AFT SILL WEB AT STA
254.6, BETWEEN S-9 AND
S-11 ON THE RIGHT SIDE
for any crack.
CONDITION 4:
NO CRACK FOUND ON
THE RIGHT SIDE.
4. APPROVAL
This Requirements Bulletin was examined by the Federal Aviation Administration (FAA). The changes
specified in this document comply with the applicable regulations and are FAA approved, as well as European
Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved
airplanes listed in the service bulletin effectivity. This document and its approval were based on the airplane
in its original Boeing delivery configuration or as modified by other Boeing changes.
If an airplane has a non-Boeing modification or repair that affects a component or system also affected by
this Requirements Bulletin, the operator is responsible for obtaining appropriate regulatory agency approval
before incorporating this Requirements Bulletin.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: December 11, 2017
737-53A1377 RB
7 of 18
REQUIREMENTS BULLETIN 737-53A1377
ALERTALERT

### Page 8

Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: December 11, 2017
737-53A1377 RB
8 of 18
REQUIREMENTS BULLETIN 737-53A1377
ALERTALERT
BLANK PAGE

### Page 9

5.    ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL INFORMATION
NOTE: 1. Unless shown differently, these dimensions and tolerances are used:
– Linear dimensions are in inches
– Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus
or minus 0.03 inch
– Tolerance on rivet and bolt edge margin is plus or minus 0.05 inch
– Angular tolerance is plus or minus 2 degrees
– Hole dimensions for standard solid rivets and fasteners are in Structural Repair
Manual (SRM) Chapter 51
– Torque Values:
– Values for structural fasteners are given in 737 Structural Repair Manual,
Chapter 51.
– Values for airframe maintenance tasks are included in Chapter 20 of 737
Aircraft Maintenance Manual (AMM).
– Values for electrical maintenance tasks are included in Chapter 20 of
Standard Wiring Practices Manual (SWPM).
– Values for engine maintenance tasks are included in Chapter 70 of 737
Aircraft Maintenance Manual (AMM).
– Non-standard torque values for maintenance tasks are included in the
applicable installation step.
2. These work instructions refer to procedures included in other Boeing documents.
When the words "refer to" are used and the operator has an accepted alternative
procedure, the accepted alternative procedure can be used. When the words "in
accordance with" are included in the instruction, the procedure in the Boeing document
must be used.
3. Use the approved fastener, process and material substitutions in accordance with
SRM Chapter 51.
4. Boeing Service Letter 737-SL-51-042, Damage Reporting and Repair Plan/Design
Guidelines, is an acceptable procedure to request information from Boeing for
additional structural repair instructions. The Service Letter describes what information
must be provided to Boeing before a structural repair can be provided.
5. The instructions in WORK INSTRUCTIONS and the figures can include operation
of tools or test equipment. Boeing Engineering Tool Drawings, the Illustrated Tool
and Equipment Manual, and the Special Tool and Ground Handling Drawing Index
contain data on versions of the tools or test equipment that you can use. It is permitted
to use replaced tools. It is not permitted to use superseded tools.
6. If it is necessary to remove more parts for access, you can remove those parts. If
you can get access without removing identified parts, it is not necessary to remove
all of the identified parts. Jacking and shoring limitations must be observed.
7. Where the work instructions include installation of a kept part, a new or serviceable
part with the same part number can be installed as an alternative to the kept part.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: December 11, 2017
737-53A1377 RB
9 of 18
REQUIREMENTS BULLETIN 737-53A1377
ALERTALERT

### Page 10

8. When more than one OPTION is given for a CONDITION, do only one of the OPTION
numbers. When more than one ACTION is given for a CONDITION number or an
OPTION number, do all of the ACTION numbers for that CONDITION number or
OPTION number.
9. This is an Enhanced Required for Compliance document. There will be a separate
Service Bulletin (SB) and a separate Requirements Bulletin (RB). If an RB is mandated
by an Airworthiness Directive (AD), then all applicable requirements specified in the
RB must be done. For the related SB, some locations are marked RC Start and RC
End to identify the requirements that are restated from the RB. For the related SB,
the areas between RC Start and RC End, including sub-steps and any figures
identified between RC Start and RC End, must be done to comply with the AD.
Therefore, an Alternative Method of Compliance (AMOC) is required for any deviations
to steps between RC Start and RC End, including substeps and identified figures.
For the related SB, the steps not between RC Start and RC End may be deviated
from using accepted methods in accordance with the operator's maintenance or
inspection program without obtaining approval of an AMOC; this is provided that the
steps between RC Start and RC End, including sub-steps and identified figures, can
still be done as specified, and the airplane can be put back in an airworthy condition.
Figures not required for compliance are omitted from the RB.
10. This is an Enhanced Required for Compliance document. The Boeing processes
used to create the Service Bulletin (SB) and the Requirements Bulletin (RB) ensure
that the information between "RC Start" and "RC End" in the SB are identical to the
information in the same sections (Compliance, Work Instructions.) of the RB which
the SB refers to as the related document.
11. The compliance times for the actions in Paragraph 3.B., Work Instructions are in
Paragraph 1.E., Compliance.
B. WORK INSTRUCTIONS
Actions Required for Compliance:
1. Requirements
Group 1:
The Boeing Company endorses the FAA rules related to Limit of Validity (LOV) and recommends
immediate and permanent removal from service of any airplanes upon reaching the LOV, whether
or not it is operated under FAA jurisdiction. As such, The Boeing Company no longer provides
maintenance instructions for airplanes that have accumulated flight cycles beyond the LOV.
Airplanes in Group 1 (line number 1-291) have accumulated flight cycles beyond the LOV of the
maintenance program. 14 CFR 121.1115 and 129.115 prohibit operation of an airplane beyond
its LOV.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: December 11, 2017
737-53A1377 RB
10 of 18
REQUIREMENTS BULLETIN 737-53A1377
ALERTALERT

### Page 11

Group 2:
Table 1: High Frequency Eddy Current (HFEC) Inspection of the Windshield No 3, Aft Sill Web at STA
254.6, Between S-9 and S-11 on the Left and Right Side of the Airplane for Any Crack.
Refer to the listed proce-
dures in SB 737-
53A1377 Original Issue
or later approved revi-
sions as an accepted
procedure
Method of ComplianceActionCondition
Access:-Do a HIGH FREQUENCY
EDDY CURRENT (HFEC)
INSPECTION OF THE
WINDSHIELD NO. 3, AFT
SILL WEB AT STA 254.6,
BETWEEN S-9 AND S-11
ON THE LEFT AND RIGHT
SIDE for any crack.
All airplanes.
PART 1: GET ACCESS
TO THE WINDSHIELD
NO. 3, AFT SILL WEB AT
STA 254.6, LEFT AND
RIGHT SIDE.
-FIGURE 3 and FIGURE 4.
Restoration:-Contact The Boeing Compa-
ny for repair instructions
and do the repair.
CONDITION 1:
ANY CRACK FOUND
ON THE LEFT SIDE.
PART 2: CLOSE AC-
CESS TO THE WIND-
SHIELD NO. 3, AFT SILL
WEB AT STA 254.6,
LEFT SIDE.
Restoration:--CONDITION 2:
PART 2: CLOSE AC-
CESS TO THE WIND-
SHIELD NO. 3, AFT SILL
WEB AT STA 254.6,
LEFT SIDE.
NO CRACK FOUND
ON THE LEFT SIDE.
Access:-Repeat the HIGH FRE-
QUENCY EDDY CURRENT
(HFEC) INSPECTION OF
THE WINDSHIELD NO. 3,
AFT SILL WEB AT STA
254.6, BETWEEN S-9 AND
S-11 ON THE LEFT SIDE
for any crack.
PART 1: GET ACCESS
TO THE WINDSHIELD
NO. 3, AFT SILL WEB AT
STA 254.6, LEFT SIDE.
-FIGURE 3
Restoration:-Contact The Boeing Compa-
ny for repair instructions
and do the repair.
CONDITION 3:
ANY CRACK FOUND
ON THE RIGHT SIDE.
PART 2: CLOSE AC-
CESS TO THE WIND-
SHIELD NO. 3, AFT SILL
WEB AT STA 254.6,
RIGHT SIDE.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: December 11, 2017
737-53A1377 RB
11 of 18
REQUIREMENTS BULLETIN 737-53A1377
ALERTALERT

### Page 12

Group 2:
Table 1: High Frequency Eddy Current (HFEC) Inspection of the Windshield No 3, Aft Sill Web at STA
254.6, Between S-9 and S-11 on the Left and Right Side of the Airplane for Any Crack.
Refer to the listed proce-
dures in SB 737-
53A1377 Original Issue
or later approved revi-
sions as an accepted
procedure
Method of ComplianceActionCondition
Restoration:--CONDITION 4:
PART 2: CLOSE AC-
CESS TO THE WIND-
SHIELD NO. 3, AFT SILL
WEB AT STA 254.6,
RIGHT SIDE.
NO CRACK FOUND
ON THE RIGHT SIDE.
Access:-Repeat the HIGH FRE-
QUENCY EDDY CURRENT
(HFEC) INSPECTION OF
THE WINDSHIELD NO. 3,
AFT SILL WEB AT STA
254.6, BETWEEN S-9 AND
S-11 ON THE RIGHT SIDE
for any crack.
PART 1: GET ACCESS
TO THE WINDSHIELD
NO. 3, AFT SILL WEB AT
STA 254.6, RIGHT SIDE.
-FIGURE 4
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: December 11, 2017
737-53A1377 RB
12 of 18
REQUIREMENTS BULLETIN 737-53A1377
ALERTALERT

### Page 13 (OCR)

REQUIREMENTS BULLETIN 737-53A1377
ALERT  ALERT
This Figure applies only to: Group 2.
STA
259.5
-ORWARD ENTRY
STA  DOOR
178
S-1L
S-2L
S-4L
S-5L
S-6L
S-7L
S-8L
S-9L  -A
S-10L
S-11L
S-12L
S-13L ~
S-14L ~
S-15L ~,
S-16L ~
STA  STA  STA
254.6  227.8  203.8
STA
259.5
VIEW FROM INSIDE
2776161
FIGURE 3: HIGH FREQUENCY EDDY CURRENT (HFEC) INSPECTION OF THE WINDSHIELD NO 3, AFT
SILL WEB AT STA 254.6, LEFT SIDE
(SHEET 1 OF 3)
Original Issue: December 11, 2017
Export Controlled ECCN: 9E991  737-53A1377 RB
Copyright © Unpublished
Work - See page 1 for details.  13 of 18

### Page 14 (OCR)

REQUIREMENTS BULLETIN 737-53A1377
ALERT  ALERT
STA  CLIP
254.6
WINDSHIELD
ASSY
SILL INSTL
CRACK
(TYPICAL)
SKIN  WINDSHIELD
ASSY
S-9L
WIRE CLAMP
(PRESENT ON SOME  / STRIP-CUSHION
CONFIGURATIONS)  - BACKING PLATE
SKIN
B
\ WIRE CLAMP
(PRESENT ON SOME
CONFIGURATIONS)
WINDSHIELD NO 3  C  •BOLT AND
AFT SILL WEB  NUT
WINDSHIELD NO 3
AFT SILL WEB
BACKING
PLATE  FWD
B-B
S-10L
SKIN  WINDSHIELD
ASSY
WIRE CLAMP
(PRESENT ON SOME
CONFIGURATIONS)
CLIP
S-11L  • STRIP-CUSHION
•BACKING PLATE
SILL INSTL
WINDSHIELD NO 3
AFT SILL WEB
FWD
A-A
C-C
HFEC INSPECTION ZONE  2776162
FIGURE 3: HIGH FREQUENCY EDDY CURRENT (HFEC) INSPECTION OF THE WINDSHIELD NO 3, AFT
SILL WEB AT STA 254.6, LEFT SIDE
(SHEET 2 OF 3)
Original Issue: December 11, 2017
Export Controlled ECCN: 9E991  Copyright © Unpublished  737-53A1377 RB
Work - See page 1 for details.  14 of 18

### Page 15

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
More DataQtyIdentificationNameTaskStep
(a)(b)1-Aft Sill WebInspect1
(a) Do a High Frequency Eddy Current (HFEC) Inspection of the aft sill web in the indicated area, for any
crack in accordance with 737 NDT Manual Part 6, 51-00-00 Procedure 4 or Procedure 23. Do the inspection
from the forward side of the aft sill web. A 90 degree probe with maximum 0.050 inch drop is recommended.
(b) Place the probe against the backing plate and use the backing plate as a guide for the probe. In areas
where screws interfere with the probe, use the screw assy as a guide. Above and below the backing plate,
place the probe against the surface of the windshield and use the windshield as a guide for the probe.
FIGURE 3: HIGH FREQUENCY EDDY CURRENT (HFEC) INSPECTION OF THE WINDSHIELD NO 3, AFT
SILL WEB AT STA 254.6, LEFT SIDE
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: December 11, 2017
737-53A1377 RB
15 of 18
REQUIREMENTS BULLETIN 737-53A1377
ALERTALERT

### Page 16 (OCR)

REQUIREMENTS BULLETIN 737-53A1377
ALERT  ALERT
This Figure applies only to: Group 2.
STA
259.5
FORWARD GALLEY
SERVICE DOOR  STA
178
→S-1R
→ S-2R
—S-AR
—S-5R
→S-6R
→ S-7R
— S-8R
— S-9R
3-S-10R  ,—S-11R
3-S-12R
— S-13R
₴~ S-14R
₴— S-15R
₴— S-16R
STA  STA  STA
203.8  227.8  254.6
STA
259.5
VIEW FROM INSIDE
2776166
FIGURE 4: HIGH FREQUENCY EDDY CURRENT (HFEC) INSPECTION OF THE WINDSHIELD NO 3, AFT
SILL WEB AT STA 254.6, RIGHT SIDE
(SHEET 1 OF 3)
Original Issue: December 11, 2017
Export Controlled ECCN: 9E991  737-53A1377 RB
Copyright © Unpublished
Work - See page 1 for details.  16 of 18

### Page 17 (OCR)

REQUIREMENTS BULLETIN 737-53A1377
ALERT  ALERT
STA
WINDSHIELD  CLIPI  254.6
ASSY
SILL INSTL
CRACK
(TYPICAL)
WINDSHIELD  SKIN
ASSY
- S-9R
STRIP-CUSHION
BACKING PLATE •  WIRE CLAMP  (PRESENT FOR SOME
CONFIGURATIONS)
WIRE CLAMP
(PRESENT FOR SOME  SKIN
CONFIGURATIONS)
BOLT AND
NUT  WINDSHIELD NO 3
AFT SILL WEB
WINDSHIELD NO 3
AFT SILL WEB  BACKING
PLATE
B-B
• S-10R
WINDSHIELD  SKIN
ASSY  WIRE CLAMP
(PRESENT FOR SOME
CONFIGURATIONS)
_CLIP
STRIP-CUSHION  - S-11R
BACKING PLATE
SILL INSTL
WINDSHIELD NO 3
AFT SILL WEB
INBD
C-C
HFEC INSPECTION ZONE  A-A
2776167
FIGURE 4: HIGH FREQUENCY EDDY CURRENT (HFEC) INSPECTION OF THE WINDSHIELD NO 3, AFT
SILL WEB AT STA 254.6, RIGHT SIDE
(SHEET 2 OF 3)
Original Issue: December 11, 2017
Export Controlled ECCN: 9E991  737-53A1377 RB
Copyright © Unpublished
Work - See page 1 for details.  17 of 18

### Page 18

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
More DataQtyIdentificationNameTaskStep
(a)(b)1-Aft Sill WebInspect1
(a) Do a High Frequency Eddy Current (HFEC) Inspection of the aft sill web in the indicated area, for any
crack in accordance with 737 NDT Manual Part 6, 51-00-00 Procedure 4 or Procedure 23. Do the inspection
from the forward side of the aft web. A 90 degree probe with maximum 0.050 inch drop is recommended.
(b) Place the probe against the backing plate and use the backing plate as a guide for the probe. In areas
where screws interfere with the probe, use the screw assy as a guide. Above and below the backing plate,
place the probe against the surface of the windshield and use the windshield as a guide for the probe.
FIGURE 4: HIGH FREQUENCY EDDY CURRENT (HFEC) INSPECTION OF THE WINDSHIELD NO 3, AFT
SILL WEB AT STA 254.6, RIGHT SIDE
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: December 11, 2017
737-53A1377 RB
18 of 18
REQUIREMENTS BULLETIN 737-53A1377
ALERTALERT

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
