# Boeing Alert Service Bulletin 737-57A1327: Revision 2

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2018-0409; AD 2019-03-07 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Alert Service Bulletin 737-57A1327](https://openairdocs.org/service-documents/boeing/737-57a1327.md)
- Title as filed: SB 737-57A1327, Rev. 2 - NG Krueger flap inspection
- Pages: 66
- PDF: https://openairdocs.org/files/sha256/12/bd/12bdd8628f18252b510179ce2df08c43f17028648df70e4ca33cf76f5d6f91d7
- Page: https://openairdocs.org/service-documents/boeing/737-57a1327/file/12bdd8628f18

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Commercial 
Airplanes
737
Service Bulletin
ALERT
Number: 737-57A1327
Original Issue: May 20, 2016
Revision 2: July 25, 2017
ATA System: 5740
SUBJECT: WINGS - Leading Edge And Leading Edge Devices - Krueger Flap Inspection
Export of this technology is controlled under the United States Export Administration Regulations (EAR) (15
CFR 300-774). An export license may be required before it is used for development, production or use by foreign
persons from specific countries. The controller of this data has the individual responsibility to abide by all export
laws.
9E991ECCN:
BOEING PROPRIETARY, CONFIDENTIAL AND/OR TRADE SECRET
Copyright © 2016 Boeing.
Unpublished Work. All Rights Reserved.
Treatment of this document and its content is governed by contract with Boeing. Rights to use this document
are licensed on a per aircraft basis and such rights may not be transferable. For more information, contact The
Boeing Company.
Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner,
BBJ, DC-8, DC-9, DC-10, KC-10, KC-46, KDC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8, Poseidon and
Boeing liveries are all trademarks owned by The Boeing Company; and no trademark license is granted in
connection with this document unless provided in writing by Boeing.
Original Issue: May 20, 2016
737-57A1327Revision 2: July 25, 2017
1 of 66
4.0

### Page 2

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 2: July 25, 2017
2 of 66
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT
BLANK PAGE

### Page 3

Table of Contents
Revision Transmittal Sheet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1. PLANNING INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
A. Effectivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
1. Airplanes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2. Spares Affected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
B. Concurrent Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
C. Reason . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
D. Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
E. Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
F. Approval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
G. Manpower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
H. Weight and Balance Changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
I. Electrical Load Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
J. References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
1. Existing Data: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
2. Data Supplied with this Service Bulletin: . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
3. Installation Drawings Used in the Preparation of this Service Bulletin: . . . . . . . . . . . 44
K. Publications Affected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
L. Interchangeability and Intermixability of Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
M. Software Accomplishment Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
2. MATERIAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
A. Material - Price and Availability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
B. Industry Support Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
C. Parts Necessary for Each Airplane . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
1. Kits/Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
2. Parts and Materials Supplied by the Operator . . . . . . . . . . . . . . . . . . . . . . . . 45
3. Parts Modified and Reidentified . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
4. Parts Removed and Not Replaced . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
D. Parts Necessary to Change Spares . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
E. Special Tooling - Price and Availability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
F. Special Tooling Necessary to do this Service Bulletin . . . . . . . . . . . . . . . . . . . . . . . 46
3. ACCOMPLISHMENT INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
A. GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
B. WORK INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
FIGURE 1: LEFT WING - KRUEGER FLAP 1 AND 2 BULLNOSE ATTACHMENT HARDWARE ONE-TIME
INSPECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
FIGURE 2: RIGHT WING - KRUEGER FLAP 3 AND 4 BULLNOSE ATTACHMENT HARDWARE ONE-TIME
INSPECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
FIGURE 3: LEFT WING - KRUEGER FLAP 1 AND 2 BULLNOSE ATTACHMENT HARDWARE
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
FIGURE 4: RIGHT WING - KRUEGER FLAP 3 AND 4 BULLNOSE ATTACHMENT HARDWARE
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
APPENDIX A: LOGIC DIAGRAM FOR PARAGRAPH 1.E. COMPLIANCE: TABLE 1: KRUEGER FLAP
BULLNOSE ATTACHMENT HARDWARE ONE-TIME INSPECTION.  [Group 1] . . . . . . 63
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 2: July 25, 2017
3 of 66
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 4

APPENDIX B: LOGIC DIAGRAM FOR PARAGRAPH 1.E. COMPLIANCE: TABLE 2: KRUEGER FLAP
BULLNOSE ATTACHMENT HARDWARE ONE-TIME INSPECTION  [Group 2] . . . . . . 64
APPENDIX C: LOGIC DIAGRAM FOR PARAGRAPH 1.E. COMPLIANCE: TABLE 3: KRUEGER FLAP
BULLNOSE ATTACHMENT HARDWARE ONE-TIME INSPECTION ON REPLACED KRUEGER
FLAPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 2: July 25, 2017
4 of 66
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 5

Commercial 
Airplanes
737
Service Bulletin
ALERT
Revision Transmittal SheetNumber: 737-57A1327Original Issue: May 20, 2016
Revision 2: July 25, 2017
ATA System: 5740
SUBJECT: WINGS - Leading Edge And Leading Edge Devices - Krueger Flap Inspection
This revision includes all pages of the service bulletin.
COMPLIANCE INFORMATION RELATED TO THIS REVISION
Federal Aviation Administration (FAA) Notice of Proposed Rule Making NPRM 2016-NM-091-AD, is related to
this service bulletin.
The Federal Aviation Administration (FAA) will possibly release an additional Airworthiness Directive related to
this service bulletin. The Airworthiness Directive will make the compliance tasks and times given in this service
bulletin mandatory.
Effects of this Revision on airplanes on which Original Issue or Revision 1 was previously done:
ActionConditionGroup
Airplanes that have replaced any
Krueger Flap no. 1, 2, 3, or 4 after
accomplishment of the one-time in-
spection on a given Krueger Flap,
determine if the replaced Krueger
Flap has accomplished this service
bulletin.
All Airplanes1
Do a one-time detailed inspection
for discrepancies in the bullnose at-
tachment hardware of the replaced
Krueger flap and any corrective ac-
tions at the times specified in Para-
graph 1.E., Compliance.
Airplanes with any Krueger flap 1,
2, 3, or 4 replaced with a Krueger
flap that has not accomplished this
service bulletin or with a Krueger
flap where the accomplishment of
this service bulletin is not known.
No further action required on the re-
placed Krueger flap.
Airplanes with any Krueger flap 1,
2, 3, or 4 replaced with a Krueger
flap that has accomplished this ser-
vice bulletin.
Airplanes line number 5503-6421 were added to Group 2 of this service bulletin effectivity.
Airplanes line number 6422-6465 were added to Group 3 of this service bulletin effectivity.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 2: July 25, 2017
5 of 66

### Page 6

REASON FOR REVISION
This revision is sent to give alternative repair instructions to replace cracked or deformed bullnose hinge lugs
or clevis assemblies on the affected Krueger flap instead of replacing the entire Krueger flap if any crack or
deformation is found on bullnose hinge lugs or clevis assemblies after the initial inspection of the attachment
hardware. This revision is also sent to add airplanes in the effectivity due to a recent incident of missing Bullnose
attachment hardware and address Krueger flaps that are replaced on the airplane.
These sections were changed:
1. Summary, Background - added in-service event information and new SRP reference.
2. Summary, Action - Split actions by airplane grouping. Also added information that cracked or deformed
parts of the flap can be replaced instead of replacing the entire flap and added actions for airplanes
that have replaced any Krueger flap 1, 2, 3, or 4.
3. Summary, Compliance - added NPRM information.
4. Summary, Manpower - added manpower information for added airplanes.
5. Paragraph 1.A., Effectivity, added airplanes and updated effectivity information and spares information.
6. Paragraph 1.C., Reason - added in-service event information, new SRP reference, and reason for this
revision.
7. Paragraph 1.D., Description - Split actions by airplane grouping. Added information that cracked or
deformed parts of the flap can be replaced instead of replacing the entire flap and added actions for
airplanes that have replaced any Krueger flap 1, 2, 3, or 4. Also added Effects of this Revision on
airplanes on which Original Issue or Revision 1 was previously done.
8. Paragraph 1.E., Compliance - added NPRM information, updated group information, added information
that cracked or deformed parts of the flap can be replaced instead of replacing the entire flap, and
added compliance tables for added airplanes and airplanes with replaced Krueger flaps.
9. Paragraph 1.F., Approval - added information for airplanes with Supplemental Type Certificate (STC)
number ST00830SE installed.
10. Paragraph 1.J., References - updated the reference list.
11. Paragraph 3.B., Work Instructions - added instruction to replace cracked or deformed parts of the flap
as an alternative action and added instructions for airplanes that have replaced any Krueger flap 1, 2,
3, or 4. Also applied group information to the work instructions.
12. APPENDIX A - added information that cracked or deformed parts of the flap can be replaced instead
of replacing the entire flap and applied the logic diagram to Group 1 airplanes.
13. Added APPENDIX B to provide a logic diagram for Group 2 airplanes.
14. Added APPENDIX C to provide a logic diagram for airplanes with replaced Krueger flaps.
Vertical lines are put on the left edge of each page, except in Paragraph 1.A., Effectivity and format changes,
to show the location of all content changes.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 2: July 25, 2017
6 of 66
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 7

Pages with no vertical lines have no changes.
REVISION HISTORY
May 20, 2016Original Issue:
September 28, 2016Revision 1:
July 25, 2017Revision 2:
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 2: July 25, 2017
7 of 66
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 8

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 2: July 25, 2017
8 of 66
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT
BLANK PAGE

### Page 9

Commercial 
Airplanes
737
Service Bulletin
ALERT
SummaryNumber: 737-57A1327Original Issue: May 20, 2016
Revision 2: July 25, 2017
ATA System: 5740
SUBJECT: WINGS - Leading Edge And Leading Edge Devices - Krueger Flap Inspection
THIS DOCUMENT IS SENT TO THE OPERATORS OF RECORD OF THE AIRPLANES SHOWN IN
PARAGRAPH 1.A., EFFECTIVITY. IF AN AIRPLANE HAS BEEN LEASED OR SOLD, SEND THIS DOCUMENT
TO THE NEW OPERATOR. IF APPLICABLE SPARES HAVE BEEN SOLD, SEND THIS DOCUMENT TO THE
NEW OWNER.
CONCURRENT REQUIREMENTS
None.
BACKGROUND
The bullnose of a 737-800 Krueger Flap departed an airplane during taxi and caused damage to the wing
structure and part of the thrust reverser. There have been six (6) other in-service reports of missing bullnose
attachment hardware resulting in a bullnose droop condition but no departure of the part from the airplane. If
this service bulletin is not accomplished, the Krueger Flap bullnose could depart the airplane during flight, which
could damage empennage structure leading to inability to maintain continued safe flight and landing.
After the release of Revision 1 of the service bulletin, an operator had an air turn back due to flight crew reporting
flap retract light remaining ON after flap was retracted during take off phase. Upon landing, the ground crew
found that the #2 Krueger Flap bullnose hinge bolt was missing. This incident occurred on an airplane that was
not in the effectivity of Original Issue and Revision 1. Boeing has determined that loss of the bolt is related to
improper installation of the bullnose hardware and some limited airplanes not in the effectivity of Original Issue
and Revision 1 are still subject to this possible issue during production.
Boeing Fleet Team Digest (FTD) 737NG FTD 57-15003 is related to this service bulletin.
Boeing Service Related Problem (SRP) 737NG-57-0283 is related to this service bulletin.
Boeing Service Related Problem (SRP) 737NG-57-0313 is related to this service bulletin.
This table is provided to operators for planning purposes only. Refer to the applicable sections for more
information.
ReferenceAffectedPlanning Data
Paragraph 1.A.2., Spares AffectedYesSpares Affected
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 2: July 25, 2017
9 of 66

### Page 10

ReferenceAffectedPlanning Data
Paragraph 1.E., Compliance and Paragraph
1.F., Approval
YesAD Related
Paragraph 1.H., Weight and Balance ChangesNoWeight and Balance Change
Paragraph 1.I., Electrical Load DataNoElectrical Load Changed
Paragraph 1.K., Publications AffectedNoPublications Affected
Paragraph 1.K., Publications AffectedNoAirplane Flight Operations Affected (Flight Crew
Operations Manual and/or FAA Approved Air-
plane Flight Manual)
Paragraph 2.C.1., Kits/PartsNoKits/Parts Required
Paragraph 2.C.2., Parts and Materials Supplied
by the Operator
YesOperator Supplied Parts/Material
Paragraph 2.F., Special Tooling Necessary to
do this Service Bulletin
NoSpecial Tooling Required
ACTION
Group 1-2:
Krueger Flap Bullnose Attachment Hardware One-Time Inspection on Existing and Replaced Krueger
Flaps
1. Do a one-time detailed inspection for discrepancies in the bullnose attachment hardware of Krueger
Flaps no. 1, 2, 3 and 4. If any discrepancy is found, do a secondary detailed inspection for any crack
or any deformation and either replace the discrepant hardware or Krueger Flap. As an alternative to
replacement of the Krueger flap, replace the cracked or deformed parts of the flap.
2. There is no action required for airplanes with Krueger Flaps no. 1, 2, 3, and 4 not replaced after the
accomplishment of the one-time detailed inspection. Airplanes that have replaced any Krueger Flap
no. 1, 2, 3, or 4 after accomplishment of the one-time inspection on a given Krueger Flap, determine
if the replaced Krueger Flap has accomplished this service bulletin.
– If any Krueger Flap no. 1, 2, 3, or 4 is replaced with a Krueger flap that has accomplished this
service bulletin, no further action is required on the replaced Krueger flap.
– If any Krueger Flap no. 1, 2, 3, or 4 is replaced with a Krueger flap that has not accomplished this
service bulletin or with a Krueger flap where the accomplishment of this service bulletin is not
known, do a one-time detailed inspection for discrepancies in the bullnose attachment hardware
of the replaced Krueger flap. If any discrepancy is found, do a secondary detailed inspection for
any crack or any deformation and either replace the discrepant hardware or Krueger flap. As an
alternative to replacement of the Krueger flap, replace the cracked or deformed parts of the flap.
Group 3:
Krueger Flap Bullnose Attachment Hardware One-Time Inspection on Replaced Krueger Flaps
1. There is no action required for airplanes with Krueger Flaps no. 1, 2, 3, and 4 not replaced since
delivery. Determine if any Krueger Flap no. 1, 2, 3, or 4 has been replaced and if any replaced Krueger
Flap has accomplished this service bulletin.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 2: July 25, 2017
10 of 66
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 11

– If any Krueger Flap no. 1, 2, 3, or 4 is replaced with a Krueger flap that has accomplished this
service bulletin, no further action is required on the replaced Krueger flap.
– If any Krueger Flap no. 1, 2, 3, or 4 is replaced with a Krueger flap that has not accomplished this
service bulletin or with a Krueger flap where the accomplishment of this service bulletin is not
known, do a one-time detailed inspection for discrepancies in the bullnose attachment hardware
of the replaced Krueger flap. If any discrepancy is found, do a secondary detailed inspection for
any crack or any deformation and either replace the discrepant hardware or Krueger flap. As an
alternative to replacement of the Krueger flap, replace the cracked or deformed parts of the flap.
EFFECTIVITY
737-600/700/700C/800/900/900ER Airplane(s). Refer to Paragraph 1.A.1., Airplanes, for the list of affected
airplanes.
Refer to Paragraph 1.A.2., Spares Affected, for the list of affected components.
COMPLIANCE
Federal Aviation Administration (FAA) Notice of Proposed Rule Making NPRM 2016-NM-091-AD, is related to
this service bulletin.
The Federal Aviation Administration (FAA) will possibly release an additional Airworthiness Directive related to
this service bulletin. The Airworthiness Directive will make the compliance tasks and times given in this service
bulletin mandatory.
Refer to Paragraph 1.E., Compliance.
INDUSTRY SUPPORT INFORMATION
Boeing warranty remedies are available for airplanes in warranty as of January 28, 2015 Please refer to Paragraph
2.B., Industry Support Information. The warranty remedies will expire eight years from the original issue date of
this service bulletin.
MANPOWER
Elapsed HoursTotal Task HoursAirplanes
2.802.80Group 1, Group
2, and Group 3
MATERIAL INFORMATION
Operator Supplied Parts/Materials.
Refer to Paragraph 2.A., Material - Price and Availability.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 2: July 25, 2017
11 of 66
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 12 (OCR)

BOEING SERVICE BULLETIN 737-57A1327
ALERT  ALERT
LE STA  LE STA
218.88  206.32  LE STA
190.85  LE STA
180.52  LE STA
166.32 LE STA
158.82
INBD
NO. 1 KRUEGER FLAP IS SHOWN
NO. 4 KRUEGER FLAP IS OPPOSITE
LE STA
150.82
DO A ONE-TIME DETAILED
INSPECTION FOR DISCREPANCIES
IN THE ATTACHMENT HARDWARE.
LE STA
104.52
INBD
DO A ONE-TIME DETAILED
NO. 2 KRUEGER FLAP IS SHOWN,  INSPECTION FOR DISCREPANCIES
NO. 3 KRUEGER FLAP IS OPPOSITE  IN THE ATTACHMENT HARDWARE.  2483896
Original Issue: May 20, 2016
Revision 2: July 25, 2017  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  737-57A1327
Work - See page 1 for detalls.  12 of 66

### Page 13

Commercial 
Airplanes
737
Service Bulletin
ALERT
Number: 737-57A1327
Original Issue: May 20, 2016
Revision 2: July 25, 2017
ATA System: 5740
SUBJECT: WINGS - Leading Edge And Leading Edge Devices - Krueger Flap Inspection
THIS DOCUMENT IS SENT TO THE OPERATORS OF RECORD OF THE AIRPLANES SHOWN IN
PARAGRAPH 1.A., EFFECTIVITY. IF AN AIRPLANE HAS BEEN LEASED OR SOLD, SEND THIS DOCUMENT
TO THE NEW OPERATOR. IF APPLICABLE SPARES HAVE BEEN SOLD, SEND THIS DOCUMENT TO THE
NEW OWNER.
1.    PLANNING INFORMATION
A. Effectivity
1. Airplanes
This service bulletin is applicable to 737-600, -700, -700C, -800, -900, -900ER Airplanes line
numbers 1-6465 in 3 Groups. The Variable Numbers and Group Information for the applicable
airplanes is given below.
Refer to Service Bulletin Index D6-19567 Part 3 for Airplane Variable Number, Line Number, and
Serial Number data.
DESCRIPTIONCONFIGURATIONGROUP
737-600, -700, -700C, -800, -900, -900ER Airplanes, line numbers
1-5502. These airplanes may have discrepant Bullnose attachment
hardware.
-1
737-600, -700, -700C, -800, -900, -900ER Airplanes, line numbers
5503-6421. These airplanes may have discrepant Bullnose
attachment hardware.
-2
737-600, -700, -700C, -800, -900, -900ER Airplanes, line number
6422-6465. These airplanes have had the intent of this service bulletin
incorporated in production.
-3
Airplane Models:
737-600, 737-700, 737-700C, 737-800, 737-900, 737-900ER
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 2: July 25, 2017
13 of 66

### Page 14

GroupVariable Number
1YA001 - YA099
1YA101 - YA199
1YA201 - YA211
1YA221
1YA231 - YA242
1YA251 - YA256
1YA271 - YA272
1YA291
1YA301 - YA302
1YA311 - YA314
1YA321 - YA323
1YA336 - YA345
1YA351
1YA356 - YA357
1YA366 - YA367
1YA371 - YA377
1YA501 - YA536
1YA541 - YA552
1YA571 - YA578
1YA601 - YA615
1YA621 - YA622
1YA626 - YA631
1YA635 - YA636
1YA641 - YA642
1YA645 - YA650
1YA656 - YA659
1YA666 - YA667
1YA671 - YA672
1YA681 - YA691
1YA701 - YA710
1YA721 - YA722
1YA731 - YA734
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 2: July 25, 2017
14 of 66
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 15

GroupVariable Number
1YA751 - YA756
1YA801 - YA803
1YA809
1YA811 - YA814
1YA831 - YA835
1YA841 - YA862
1YA881 - YA882
1YA891 - YA892
1YA961 - YA978
1YB001 - YB006
1YB101 - YB132
1YB151 - YB153
1YB156 - YB158
1YB161 - YB164
1YB171 - YB172
1YB181 - YB184
1YB201 - YB208
1YB271
1YB276
1YB301 - YB310
1YB371 - YB392
1YB501 - YB502
1YB521 - YB526
1YB541 - YB544
1YB551
1YB561 - YB598
1YB601 - YB636
1YB651
1YB656
1YB671 - YB672
1YB851 - YB863
1YB871 - YB874
1YB881 - YB893
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 2: July 25, 2017
15 of 66
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 16

GroupVariable Number
1YB901 - YB903
1YB911
1YB961 - YB975
1YB981
1YB986 - YB998
1YC001 - YC030
1YC051 - YC084
1YC091 - YC095
1YC101 - YC104
1YC111 - YC113
1YC121
1YC126 - YC127
1YC136 - YC141
1YC146 - YC147
1YC151 - YC156
1YC166 - YC171
1YC176 - YC179
1YC186 - YC190
1YC201 - YC203
1YC206 - YC207
1YC301 - YC305
1YC321 - YC387
1YC391 - YC394
1YC396
1YC401 - YC417
1YC421 - YC422
1YC426 - YC428
1YC436 - YC439
1YC441 - YC448
1YC451 - YC455
1YC459
1YC461 - YC467
1YC471 - YC499
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 2: July 25, 2017
16 of 66
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 17

GroupVariable Number
1YC501 - YC526
1YC571 - YC583
1YC587 - YC589
1YC591 - YC593
1YC601 - YC655
1YC681 - YC696
1YC701 - YC715
1YC720 - YC725
1YC727 - YC752
1YC761 - YC770
1YC781 - YC793
1YC801 - YC892
1YC901 - YC907
1YC921 - YC922
1YC931 - YC932
1YC941 - YC951
1YC971 - YC978
1YC981 - YC983
1YD001 - YD007
1YD021 - YD025
1YD041 - YD057
1YD081 - YD084
1YD101 - YD117
1YD121 - YD126
1YD151 - YD159
1YD171 - YD172
1YD201 - YD203
1YD206 - YD209
1YD216 - YD219
1YD251 - YD254
1YD256 - YD257
1YD261
1YD301 - YD334
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 2: July 25, 2017
17 of 66
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 18

GroupVariable Number
1YD391
1YD401 - YD410
1YD412 - YD422
1YD481 - YD485
1YD491 - YD499
1YD501 - YD512
1YD531 - YD535
1YD541 - YD547
1YD561 - YD564
1YD571 - YD572
1YD591 - YD595
1YD601 - YD612
1YD651 - YD655
1YE001 - YE020
1YE051
1YE101 - YE109
1YE151 - YE157
1YE171 - YE172
1YE201 - YE206
1YE301 - YE305
1YE321 - YE326
1YE371 - YE383
1YF001 - YF011
1YF021 - YF049
1YF051 - YF080
1YF086 - YF087
1YF106 - YF107
1YF111 - YF114
1YF116 - YF119
1YF121 - YF132
1YF176 - YF178
1YF191 - YF192
1YF201 - YF276
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 2: July 25, 2017
18 of 66
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 19

GroupVariable Number
1YF401 - YF402
1YF431 - YF432
1YF436 - YF437
1YF441 - YF442
1YF451 - YF460
1YF501 - YF599
1YF601 - YF682
2YF683 - YF685
2YF691 - YF695
1YF701 - YF707
1YF801 - YF805
1YF831 - YF832
1YF836 - YF838
1YF871 - YF872
1YF901 - YF905
1YF921 - YF928
1YF951 - YF954
1YG001 - YG044
1YG061 - YG064
1YG066 - YG089
1YG091 - YG099
1YG101 - YG104
1YG111 - YG114
1YG116 - YG143
2YG144 - YG146
1YG201 - YG205
1YG211 - YG214
1YG221 - YG224
1YG251 - YG252
1YG501 - YG514
2YG515
1YG601 - YG602
1YG701
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 2: July 25, 2017
19 of 66
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 20

GroupVariable Number
1YG711
2YG721 - YG722
1YH001 - YH012
1YH031 - YH055
1YH071 - YH080
1YH101 - YH132
1YH201 - YH202
1YH206 - YH207
1YH301 - YH306
2YH307
1YH321 - YH322
1YH501 - YH542
1YH551 - YH594
1YH601 - YH606
1YH611 - YH620
1YH631 - YH632
1YH636 - YH637
1YH641
1YH681 - YH683
2YH684 - YH685
1YH701 - YH728
2YH729 - YH750
1YH751 - YH754
2YH755
1YH801 - YH843
2YH844 - YH878
3YH879
1YH901 - YH905
2YH906 - YH908
1YH911 - YH915
1YH951 - YH952
1YJ001 - YJ013
1YJ021
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 2: July 25, 2017
20 of 66
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 21

GroupVariable Number
1YJ471 - YJ480
1YJ501 - YJ517
1YJ531 - YJ579
1YJ591 - YJ599
1YJ631 - YJ632
1YJ671 - YJ694
1YJ801 - YJ867
1YJ871 - YJ880
1YJ901 - YJ904
1YJ908 - YJ929
1YJ931 - YJ937
1YJ941 - YJ956
1YJ961
1YJ976 - YJ977
1YK001 - YK007
1YK101 - YK104
1YK111 - YK112
1YK121 - YK122
1YK131 - YK133
1YK136 - YK139
1YK141 - YK142
1YK146 - YK148
1YK151 - YK154
1YK161 - YK167
1YK171
1YK176 - YK177
1YK186
1YK191
1YK196
1YK201 - YK202
1YK301 - YK314
1YK321 - YK340
1YK361 - YK378
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 2: July 25, 2017
21 of 66
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 22

GroupVariable Number
1YK401 - YK406
1YK426 - YK427
1YK431 - YK450
1YK456 - YK467
1YK471 - YK473
1YK476
2YK478
1YK480 - YK487
1YK491 - YK493
1YK495 - YK499
1YK511 - YK516
1YK521 - YK530
1YK551 - YK571
1YK576 - YK577
1YK580 - YK585
1YK601 - YK602
1YK606 - YK607
1YK611 - YK616
1YK621 - YK634
1YK641 - YK644
1YK651 - YK665
1YK671 - YK672
1YK676 - YK677
1YK681 - YK686
1YK691
1YK695 - YK699
1YK701 - YK713
1YK716 - YK719
1YK721 - YK741
1YK751 - YK770
1YK776 - YK778
1YK781 - YK785
1YK791 - YK792
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 2: July 25, 2017
22 of 66
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 23

GroupVariable Number
1YK796 - YK797
1YK801 - YK899
1YK901 - YK912
1YK918 - YK919
1YK921 - YK929
1YK941 - YK999
1YL001 - YL005
1YL011 - YL016
1YL021 - YL024
1YL051 - YL052
1YL056 - YL057
1YL061
1YL066 - YL069
1YL076 - YL077
1YL101 - YL137
1YL201 - YL237
1YL241 - YL242
1YL271 - YL272
1YL281 - YL284
1YL301 - YL303
1YL311 - YL314
1YL316 - YL321
1YL351 - YL353
1YL371 - YL374
1YL401
1YL421 - YL429
1YL431 - YL444
1YL461 - YL478
1YL501 - YL509
1YL531 - YL534
1YL541 - YL551
1YL561 - YL579
1YL591 - YL598
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 2: July 25, 2017
23 of 66
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 24

GroupVariable Number
1YL601 - YL606
1YL611 - YL612
1YL616 - YL617
1YL621
1YL626
1YL631 - YL634
1YL636 - YL637
1YL661 - YL664
1YL676 - YL691
1YL696 - YL697
1YL701 - YL707
1YL731
1YL751 - YL752
1YL756 - YL757
1YL761 - YL780
1YL796 - YL797
1YL801 - YL815
1YL901 - YL910
1YL921 - YL940
1YL951 - YL968
1YM101 - YM103
1YM201 - YM244
1YM251 - YM299
1YM301 - YM399
1YM401 - YM415
1YM471
1YM481 - YM484
1YM501 - YM515
1YM521 - YM522
1YM541
1YM551 - YM553
1YM571 - YM572
1YM581 - YM582
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 2: July 25, 2017
24 of 66
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 25

GroupVariable Number
1YM591 - YM599
1YM631 - YM634
1YM641 - YM652
1YM671 - YM674
1YM691 - YM699
1YM701 - YM710
1YM761 - YM765
1YM771 - YM779
1YN001 - YN016
1YN021 - YN024
1YN061
1YN071 - YN082
1YN091 - YN092
1YN101 - YN112
1YN121
1YN126
1YN201 - YN202
1YN211 - YN219
1YN231 - YN236
1YN261
1YN501
1YN531 - YN534
1YN551 - YN564
2YN565 - YN566
1YN581 - YN585
1YN591 - YN592
2YN593
1YN601 - YN606
1YN651 - YN653
2YN661 - YN663
3YN671
1YN701 - YN702
1YN741 - YN746
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 2: July 25, 2017
25 of 66
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 26

GroupVariable Number
1YN756
2YN757 - YN758
1YQ001 - YQ003
1YQ011 - YQ021
1YQ026 - YQ029
1YQ036 - YQ045
1YQ201 - YQ207
1YQ231
1YQ241 - YQ251
1YQ281 - YQ284
1YQ291 - YQ296
1YQ301 - YQ302
1YQ321 - YQ324
1YQ331 - YQ334
1YQ346 - YQ347
1YQ351
2YQ352 - YQ365
2YQ371
1YQ401 - YQ403
1YQ451 - YQ454
1YQ456
1YQ461
1YQ471
1YQ501 - YQ519
2YQ520
1YR001 - YR043
2YR044 - YR050
1YR051 - YR087
2YR088 - YR090
1YR091 - YR098
1YR101 - YR105
1YR111 - YR124
1YR126 - YR144
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 2: July 25, 2017
26 of 66
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 27

GroupVariable Number
1YR166 - YR182
1YR186 - YR198
1YR201 - YR204
2YR205 - YR211
1YR231 - YR294
1YR296 - YR297
1YR301 - YR334
1YR338 - YR341
1YR361 - YR366
1YR371 - YR373
1YR376
2YR377
1YR381 - YR382
1YR386 - YR388
1YR391
1YR396 - YR398
2YR399
1YR401 - YR405
1YR411 - YR413
1YR416 - YR418
1YR421 - YR424
1YR426 - YR455
1YR457 - YR499
1YR501 - YR506
1YR511 - YR520
1YR526 - YR544
1YR546 - YR551
1YR556 - YR562
1YR571 - YR582
1YR591 - YR592
1YR601 - YR605
1YR616 - YR658
1YR661 - YR663
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 2: July 25, 2017
27 of 66
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 28

GroupVariable Number
1YR671 - YR672
2YR673
1YR676 - YR678
1YR681 - YR682
1YR701 - YR769
1YR771 - YR799
1YR801 - YR816
2YR817 - YR822
1YR831 - YR838
1YR841 - YR897
2YR898 - YR899
1YR901 - YR903
1YR931 - YR934
1YR938 - YR944
1YR951 - YR970
2YR971 - YR980
1YR981 - YR996
2YR997 - YR998
1YS001 - YS002
1YS006 - YS009
1YS031 - YS032
1YS051 - YS073
1YS101 - YS120
1YS126 - YS137
2YS138 - YS142
2YS146 - YS150
1YS151 - YS160
1YS166 - YS194
1YS196 - YS197
1YS201 - YS209
1YS221 - YS225
1YS231 - YS236
1YS271 - YS286
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 2: July 25, 2017
28 of 66
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 29

GroupVariable Number
2YS287 - YS288
1YS301 - YS334
2YS335 - YS348
1YS351 - YS365
2YS366 - YS370
1YS371 - YS374
2YS375 - YS378
1YS381 - YS383
1YS401
1YS451
1YS456 - YS457
1YS462
2YS463 - YS465
1YS467
1YS501 - YS502
1YS506
1YS511 - YS513
2YS514 - YS518
1YS531
2YS536 - YS538
2YS541 - YS542
2YS546
1YS551 - YS553
2YS554 - YS556
1YS561 - YS578
1YS581 - YS595
1YS601 - YS690
1YS701 - YS708
2YS709 - YS710
3YS711
1YS721 - YS759
2YS760
1YS761 - YS762
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 2: July 25, 2017
29 of 66
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 30

GroupVariable Number
1YS771 - YS780
1YS806 - YS810
1YS816 - YS818
1YS823 - YS825
1YS851 - YS860
2YS861
1YS876
1YS881 - YS883
2YS896 - YS897
1YS901 - YS909
1YS911 - YS927
2YS928 - YS948
3YS949
2YS951 - YS955
1YS956 - YS957
1YS961 - YS965
2YS966 - YS974
2YS976 - YS977
1YS981 - YS983
2YS984 - YS987
1YS991 - YS998
1YT001 - YT004
1YT006
1YT026 - YT027
1YT031 - YT032
1YT036 - YT038
1YT061 - YT068
1YT101 - YT111
2YT112 - YT121
1YT126 - YT130
2YT131 - YT134
3YT135
1YT136 - YT138
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 2: July 25, 2017
30 of 66
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 31

GroupVariable Number
1YT176 - YT181
2YT182 - YT185
2YT191
1YT196 - YT197
2YT198 - YT199
1YT201
1YT206 - YT207
1YT211 - YT213
1YT251 - YT271
2YT272 - YT299
1YT301 - YT304
2YT305
1YT306 - YT307
1YT311 - YT312
1YT321 - YT327
2YT328 - YT354
2YT371
3YT372
2YT381
1YT391
2YT392 - YT396
1YT401 - YT403
1YT411 - YT415
2YT416 - YT417
1YT427
1YT461 - YT471
2YT472 - YT477
1YT491 - YT492
1YT501 - YT502
2YT503 - YT521
1YT551
2YT552
1YT556
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 2: July 25, 2017
31 of 66
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 32

GroupVariable Number
2YT557 - YT560
1YT561
2YT562 - YT563
2YT565
2YT571 - YT576
1YT601 - YT606
1YT701 - YT702
2YT703 - YT708
1YT761 - YT778
2YT779 - YT781
2YT791 - YT793
1YT796
2YT797
1YT801 - YT804
1YT811 - YT812
2YT813
2YT826 - YT827
1YT831
2YT832
2YT841 - YT844
3YT845
2YT851 - YT852
2YT856 - YT863
2YT885 - YT887
1YT891 - YT894
2YT895
1YT901 - YT908
2YT909 - YT964
3YT965 - YT972
1YU001 - YU045
2YU046 - YU060
1YU201 - YU212
2YU213 - YU216
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 2: July 25, 2017
32 of 66
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 33

GroupVariable Number
2YU301 - YU308
3YU309
1YV001
2YV002 - YV004
2YV006 - YV012
2YV021 - YV023
2YV030 - YV032
3YV033
2YV041 - YV042
2YV045 - YV047
2YV051 - YV052
2YV081
2YV083 - YV084
2YV097 - YV098
3YV099
1YV101 - YV106
2YV107 - YV142
3YV143 - YV144
2YV251 - YV252
2YV256 - YV257
2YV301 - YV312
1YV351 - YV352
2YV353 - YV368
1YV381
2YV382 - YV388
2YV391 - YV394
2YV401
2YV411
2YV431 - YV433
2YV441 - YV447
3YV448 - YV450
2YV461
3YV462
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 2: July 25, 2017
33 of 66
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 34

GroupVariable Number
2YV501 - YV504
1YV521
2YV571 - YV581
2YV601 - YV605
2YV651 - YV664
2YV695 - YV696
2YV711
2YV722 - YV731
2YV741 - YV755
3YV756 - YV758
2YV781 - YV785
3YV786
2YV801 - YV810
2YV881 - YV883
2YV901 - YV908
3YV909
2YV971 - YV978
3YV979 - YV980
2YW001
2YW011 - YW098
2YW226 - YW239
3YW240
2YW245 - YW246
3YW247
2YW261
2YW263
2YW267 - YW276
3YW277
2YW283
3YW284 - YW285
2YW292 - YW294
2YW356 - YW358
2YW361 - YW362
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 2: July 25, 2017
34 of 66
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 35

GroupVariable Number
2YW371 - YW386
2YW401
2YW451 - YW452
2YW471 - YW472
3YW491
3YW551
2YW881
2YW891 - YW893
2YW906 - YW907
2YW916 - YW918
2YW971 - YW973
2. Spares Affected
Examine your spares supply for the parts or components identified below. If any parts or components
are found, refer to Paragraph 3.B., Work Instructions for the recommended action.
Part Number
114A1110-( ) (a)
114A1220-( ) (b)
(a) This applies to any Krueger flap and bullnose assem-
bly - no. 1 and no. 4.
(b) This applies to any Krueger flap and bullnose assem-
bly - no. 2 and no. 3.
B. Concurrent Requirements
None.
C. Reason
The bullnose of a 737-800 Krueger Flap departed an airplane during taxi and caused damage to the
wing structure and part of the thrust reverser. There have been six (6) other in-service reports of missing
bullnose attachment hardware resulting in a bullnose droop condition but no departure of the part from
the airplane. If this service bulletin is not accomplished, the Krueger Flap bullnose could depart the
airplane during flight, which could damage empennage structure leading to inability to maintain continued
safe flight and landing.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 2: July 25, 2017
35 of 66
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 36

After the release of Revision 1 of the service bulletin, an operator had an air turn back due to flight
crew reporting flap retract light remaining ON after flap was retracted during take off phase. Upon
landing, the ground crew found that the #2 Krueger Flap bullnose hinge bolt was missing. This incident
occurred on an airplane that was not in the effectivity of Original Issue and Revision 1. Boeing has
determined that loss of the bolt is related to improper installation of the bullnose hardware and some
limited airplanes not in the effectivity of Original Issue and Revision 1 are still subject to this possible
issue during production.
Boeing Fleet Team Digest (FTD) 737NG FTD 57-15003 is related to this service bulletin.
Boeing Service Related Problem (SRP) 737NG-57-0283 is related to this service bulletin.
Boeing Service Related Problem (SRP) 737NG-57-0313 is related to this service bulletin.
Revision 1 is sent to give a clarification that a removal of the attachment hardware is not necessary
when accomplishing the detailed inspection of the hardware. Also this revision changes illustrations to
show correct orientation of the attachment hardware and gives minor changes on terminology and
general references.
Revision 2 is sent to give alternative repair instructions to replace cracked or deformed bullnose hinge
lugs or clevis assemblies on the affected Krueger flap instead of replacing the entire Krueger flap if
any crack or deformation is found on bullnose hinge lugs or clevis assemblies after the initial inspection
of the attachment hardware. This revision is also sent to add airplanes in the effectivity due to a recent
incident of missing Bullnose attachment hardware and address Krueger flaps that are replaced on the
airplane.
D. Description
Group 1-2:
Krueger Flap Bullnose Attachment Hardware One-Time Inspection on Existing and Replaced
Krueger Flaps
1. Do a one-time detailed inspection for discrepancies in the bullnose attachment hardware of Krueger
Flaps no. 1, 2, 3 and 4. If any discrepancy is found, do a secondary detailed inspection for any
crack or any deformation and either replace the discrepant hardware or Krueger Flap. As an
alternative to replacement of the Krueger flap, replace the cracked or deformed parts of the flap.
2. There is no action required for airplanes with Krueger Flaps no. 1, 2, 3, and 4 not replaced after
the accomplishment of the one-time detailed inspection. Airplanes that have replaced any Krueger
Flap no. 1, 2, 3, or 4 after accomplishment of the one-time inspection on a given Krueger Flap,
determine if the replaced Krueger Flap has accomplished this service bulletin.
– If any Krueger Flap no. 1, 2, 3, or 4 is replaced with a Krueger flap that has accomplished this
service bulletin, no further action is required on the replaced Krueger flap.
– If any Krueger Flap no. 1, 2, 3, or 4 is replaced with a Krueger flap that has not accomplished
this service bulletin or with a Krueger flap where the accomplishment of this service bulletin
is not known, do a one-time detailed inspection for discrepancies in the bullnose attachment
hardware of the replaced Krueger flap. If any discrepancy is found, do a secondary detailed
inspection for any crack or any deformation and either replace the discrepant hardware or
Krueger flap. As an alternative to replacement of the Krueger flap, replace the cracked or
deformed parts of the flap.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 2: July 25, 2017
36 of 66
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 37

Group 3:
Krueger Flap Bullnose Attachment Hardware One-Time Inspection on Replaced Krueger Flaps
1. There is no action required for airplanes with Krueger Flaps no. 1, 2, 3, and 4 not replaced since
delivery. Determine if any Krueger Flap no. 1, 2, 3, or 4 has been replaced and if any replaced
Krueger Flap has accomplished this service bulletin.
– If any Krueger Flap no. 1, 2, 3, or 4 is replaced with a Krueger flap that has accomplished this
service bulletin, no further action is required on the replaced Krueger flap.
– If any Krueger Flap no. 1, 2, 3, or 4 is replaced with a Krueger flap that has not accomplished
this service bulletin or with a Krueger flap where the accomplishment of this service bulletin
is not known, do a one-time detailed inspection for discrepancies in the bullnose attachment
hardware of the replaced Krueger flap. If any discrepancy is found, do a secondary detailed
inspection for any crack or any deformation and either replace the discrepant hardware or
Krueger flap. As an alternative to replacement of the Krueger flap, replace the cracked or
deformed parts of the flap.
Effects of this Revision on airplanes on which Original Issue or Revision 1 was previously done:
ActionConditionGroup
Airplanes that have replaced any
Krueger Flap no. 1, 2, 3, or 4 after
accomplishment of the one-time in-
spection on a given Krueger Flap,
determine if the replaced Krueger
Flap has accomplished this service
bulletin.
All Airplanes1
Do a one-time detailed inspection
for discrepancies in the bullnose at-
tachment hardware of the replaced
Krueger flap and any corrective ac-
tions at the times specified in Para-
graph 1.E., Compliance.
Airplanes with any Krueger flap 1,
2, 3, or 4 replaced with a Krueger
flap that has not accomplished this
service bulletin or with a Krueger
flap where the accomplishment of
this service bulletin is not known.
No further action required on the re-
placed Krueger flap.
Airplanes with any Krueger flap 1,
2, 3, or 4 replaced with a Krueger
flap that has accomplished this ser-
vice bulletin.
The work in this service bulletin is done in the maintenance zone(s) given below.
Group 1:
Affected Maintenance Zones
ZoneModel
512, 513, 612, 613737-600, 737-700, 737-700C,
737-800, 737-900, 737-900ER
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 2: July 25, 2017
37 of 66
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 38

Group 2:
Affected Maintenance Zones
ZoneModel
512, 513, 612, 613737-700, 737-700C, 737-800,
737-900ER
Group 3:
Affected Maintenance Zones
ZoneModel
512, 513, 612, 613737-700, 737-800, 737-900ER
E. Compliance
Federal Aviation Administration (FAA) Notice of Proposed Rule Making NPRM 2016-NM-091-AD, is
related to this service bulletin.
The Federal Aviation Administration (FAA) will possibly release an additional Airworthiness Directive
related to this service bulletin. The Airworthiness Directive will make the compliance tasks and times
given in this service bulletin mandatory.
Group 1:
Accomplish the required actions, based on the applicable conditions in Table 1 and Table 3, in
accordance with Paragraph 3. Accomplishment Instructions. Airplanes that have completed the actions
of Table 1 and have not replaced any Krueger Flap no. 1, 2, 3, or 4 do not need to do the actions in
Table 3.
Group 2:
Accomplish the required actions, based on the applicable conditions in Table 2 and Table 3, in
accordance with Paragraph 3. Accomplishment Instructions. Airplanes that have completed the actions
of Table 2 and have not replaced any Krueger Flap no. 1, 2, 3, or 4 do not need to do the actions in
Table 3.
Group 3:
There is no action required for airplanes with Krueger Flaps no. 1, 2, 3, and 4 not replaced since
delivery. If any Krueger Flap no. 1, 2, 3, or 4 is replaced, accomplish the required actions, based on
the applicable conditions in Table 3.
A logic diagram showing compliance tasks and compliance times tor Table 1 is included as an aid in
APPENDIX A.
A logic diagram showing compliance tasks and compliance times tor Table 2 is included as an aid in
APPENDIX B.
A logic diagram showing compliance tasks and compliance times tor Table 3 is included as an aid in
APPENDIX C.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 2: July 25, 2017
38 of 66
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 39

Group 1:
Table 1: Krueger Flap Bullnose Attachment Hardware One-Time Inspection
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
-Within 6 months af-
ter the original is-
sue date of this
service bulletin.
Do a one-time detailed
inspection for discrepan-
cies in the bullnose attach-
ment hardware of
Krueger Flaps no. 1, 2, 3
and 4.
ALL AIRPLANES.
-Before further
flight.
Do a detailed inspection
of all bullnose hinge lugs
and clevis assemblies on
the affected Krueger
Flap, for any crack or any
deformation.
CONDITION 1: ANY AT-
TACHMENT HARDWARE
DISCREPANCY FOUND
ON A KRUEGER FLAP.
-Before further
flight.
Replace affected Krueger
Flap, or replace cracked
or deformed bullnose
hinge lugs or clevis as-
semblies.
CONDITION 1.1: ANY
CRACK OR ANY DEFOR-
MATION FOUND ON
BULLNOSE HINGE LUGS
OR CLEVIS ASSEMBLIES.
-Before further
flight.
Replace discrepant
Krueger Flap bullnose at-
tachment hardware.
CONDITION 1.2: NO
CRACK OR DEFORMA-
TION FOUND ON BULL-
NOSE HINGE LUGS OR
CLEVIS ASSEMBLIES.
--No further action re-
quired.
CONDITION 2: NO AT-
TACHMENT HARDWARE
DISCREPANCY FOUND
ON A KRUEGER FLAP.
Group 2:
Table 2: Krueger Flap Bullnose Attachment Hardware One-Time Inspection
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
-Within 6 months af-
ter the Revision 2
date of this service
bulletin.
Do a one-time detailed
inspection for discrepan-
cies in the bullnose attach-
ment hardware of
Krueger Flaps no. 1, 2, 3
and 4.
ALL AIRPLANES.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 2: July 25, 2017
39 of 66
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 40

Group 2:
Table 2: Krueger Flap Bullnose Attachment Hardware One-Time Inspection
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
-Before further
flight.
Do a detailed inspection
of all bullnose hinge lugs
and clevis assemblies on
the affected Krueger
Flap, for any crack or any
deformation.
CONDITION 1: ANY AT-
TACHMENT HARDWARE
DISCREPANCY FOUND
ON A KRUEGER FLAP.
-Before further
flight.
Replace affected Krueger
Flap, or replace cracked
or deformed bullnose
hinge lugs or clevis as-
semblies.
CONDITION 1.1: ANY
CRACK OR ANY DEFOR-
MATION FOUND ON
BULLNOSE HINGE LUGS
OR CLEVIS ASSEMBLIES.
-Before further
flight.
Replace discrepant
Krueger Flap bullnose at-
tachment hardware.
CONDITION 1.2: NO
CRACK OR DEFORMA-
TION FOUND ON BULL-
NOSE HINGE LUGS OR
CLEVIS ASSEMBLIES.
--No further action re-
quired.
CONDITION 2: NO AT-
TACHMENT HARDWARE
DISCREPANCY FOUND
ON A KRUEGER FLAP.
Table 3, All Groups: Krueger Flap Bullnose Attachment Hardware One-Time Inspection on Re-
placed Krueger Flaps
Repeat In-
terval (Not
to Ex-
ceed)
Compliance TimeActionCondition
-Within 6 months after
the Revision 2 date of
this service bulletin.
Determine if any Krueger
Flap no. 1, 2, 3, or 4 has
been replaced and if any
replaced Krueger Flap has
accomplished this service
bulletin. (a)(b)
ALL AIRPLANES
--No further action required.CONDITION 3: AIR-
PLANES WITH ANY
KRUEGER FLAP NO. 1, 2,
3, OR 4 REPLACED WITH
A KRUEGER FLAP THAT
HAS ACCOMPLISHED
THIS SERVICE BULLETIN.
(b)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 2: July 25, 2017
40 of 66
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 41

Table 3, All Groups: Krueger Flap Bullnose Attachment Hardware One-Time Inspection on Re-
placed Krueger Flaps
Repeat In-
terval (Not
to Ex-
ceed)
Compliance TimeActionCondition
-Within 6 months after
the Revision 2 date of
this service bulletin.
Do a one-time detailed in-
spection for discrepancies
in the bullnose attachment
hardware of the replaced
Krueger Flap.
CONDITION 4: AIR-
PLANES WITH ANY
KRUEGER FLAP NO. 1, 2,
3, OR 4 REPLACED WITH
A KRUEGER FLAP THAT
HAS NOT ACCOM-
PLISHED THIS SERVICE
BULLETIN OR WITH A
KRUEGER FLAP WHERE
THE ACCOMPLISHMENT
OF THIS SERVICE BUL-
LETIN IS NOT KNOWN.
-Before further flight.Do a detailed inspection of
all bullnose hinge lugs and
clevis assemblies on the af-
fected Krueger Flap, for any
crack or any deformation.
CONDITION 5: ANY AT-
TACHMENT HARDWARE
DISCREPANCY FOUND
ON A KRUEGER FLAP.
-Before further flight.Replace affected Krueger
Flap, or replace cracked or
deformed bullnose hinge
lugs or clevis assemblies.
CONDITION 5.1: ANY
CRACK OR ANY DEFOR-
MATION FOUND ON
BULLNOSE HINGE LUGS
OR CLEVIS ASSEMBLIES.
-Before further flight.Replace discrepant Krueger
Flap bullnose attachment
hardware.
CONDITION 5.2: NO
CRACK OR DEFORMA-
TION FOUND ON BULL-
NOSE HINGE LUGS OR
CLEVIS ASSEMBLIES.
--No further action required.CONDITION 6: NO AT-
TACHMENT HARDWARE
DISCREPANCY FOUND
ON A KRUEGER FLAP.
(a) It is acceptable to review maintenance records to determine if this service bulletin was
accomplished on the replaced Krueger flap. If the accomplishment of this service bulletin
is not known or cannot be positively verified by maintenance records, assume that the
accomplishment of this service bulletin was not done on the replaced Krueger flap.
(b) Any Krueger Flap 1, 2, 3, or 4 originally installed on delivered Group 3 airplanes has had
the intent of this service bulletin incorporated in production. These Krueger Flaps can be
considered as having accomplished this service bulletin.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 2: July 25, 2017
41 of 66
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 42

F. Approval
NOTE: The approval statement that follows is valid for 737-700C airplanes.
This service bulletin was examined by the Federal Aviation Administration (FAA). The changes specified
in this service bulletin comply with the applicable regulations and are FAA approved for the airplanes
listed in the service bulletin effectivity. This service bulletin and its approval were based on the airplane
in its original Boeing delivery configuration or as modified by other approved Boeing changes.
This service bulletin is also approved for airplanes having FAA Aviation Partners Boeing (APB)
Supplemental Type Certificate (STC) number ST00830SE installed (not including any areas affected
by the split scimitar winglet configuration).
For 737-700C models that have APB winglets installed by STC number ST00830SE, the operator is
responsible for obtaining appropriate regulatory agency approval before incorporating this service
bulletin if the bulletin is in the area affected by blended winglets.
If an airplane has a non-Boeing modification or repair that affects a component or system also affected
by this service bulletin, the operator is responsible for obtaining appropriate regulatory agency approval
before incorporating this service bulletin.
NOTE: The approval statement that follows is valid for all affected airplanes, except 737-700C
airplanes.
This service bulletin was examined by the Federal Aviation Administration (FAA). The changes specified
in this service bulletin comply with the applicable regulations and are FAA approved, as well as European
Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved
airplanes listed in the service bulletin effectivity. This service bulletin and its approval were based on
the airplane in its original Boeing delivery configuration or as modified by other approved Boeing
changes.
This service bulletin is also approved for airplanes having FAA Aviation Partners Boeing (APB)
Supplemental Type Certificate (STC) number ST00830SE installed (not including any areas affected
by the split scimitar winglet configuration).
For BBJ models that have APB winglets installed by STC number ST00830SE, the operator is
responsible for obtaining appropriate regulatory agency approval before incorporating this service
bulletin if the bulletin is in the area affected by blended winglets.
If an airplane has a non-Boeing modification or repair that affects a component or system also affected
by this service bulletin, the operator is responsible for obtaining appropriate regulatory agency approval
before incorporating this service bulletin.
G. Manpower
The table below shows an estimate of the task hours necessary to do this inspection for each wing.
This estimate is for direct labor only, done by an experienced crew. Adjust the estimate with operator
task hour data if necessary. The estimate does not include lost time. These are some examples of lost
time:
• Time to adjust to the workplace
• Time to schedule the work
• Time to inspect the work
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 2: July 25, 2017
42 of 66
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 43

• Time to cure the materials
• Time to make the parts
• Time to find the tools
Table 1: One-Time Detailed Inspection and Installation of Bullnose Attachment Hardware
of Krueger Flaps No. 1, 2, 3, and 4
Elapsed HoursTask HoursNumber of PersonsTask
0.600.601Figure 1
0.600.601Figure 2
0.800.801Figure 3
0.800.801Figure 4
2.802.80TOTAL FOR EACH AIRPLANE
H. Weight and Balance Changes
None.
I. Electrical Load Data
Not Changed
J. References
1. Existing Data:
a. Boeing Service Related Problem (SRP) 737NG-57-0283, 737NG-57-0313
b. Component Maintenance Manual (CMM) 57-56-33, 57-56-44
c. Federal Aviation Administration (FAA) Notice of Proposed Rule Making (NPRM)
2016-NM-091-AD
d. Service Bulletin Index D6-19567
e. Standard Overhaul Practices Manual (SOPM) 20-50-01, 20-50-02
f. 737-600/700/800/900 Aircraft Maintenance Manual (AMM) 27-81-00, 27-81-11
g. 737NG Fleet Team Digest (FTD) 57-15003
2. Data Supplied with this Service Bulletin:
None.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 2: July 25, 2017
43 of 66
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 44

3. Installation Drawings Used in the Preparation of this Service Bulletin:
TitleDrawing Number
KRUEGER FLAP INSTL - INBD WING L.E.114A1001
The table above lists applicable drawings used to prepare this service bulletin. The drawings are
not necessary to make the specified changes, and are not supplied with this service bulletin. The
drawings may not be applicable to all airplane configurations or operators.
K. Publications Affected
1. Publications:
None.
2. Damage Tolerance Based Structural Inspections:
Boeing has evaluated the repairs and/or changes in this service bulletin for effects on Fatigue
Critical Structure (FCS) and for changes to Damage Tolerance Inspections (DTI) required in the
Maintenance Program. This service bulletin does not affect FCS, therefore DTIs are not necessary.
L. Interchangeability and Intermixability of Parts
Accomplishment of this service bulletin does not affect interchangeability or intermixability of parts.
M. Software Accomplishment Summary
Not affected.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 2: July 25, 2017
44 of 66
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 45

2.    MATERIAL INFORMATION
A. Material - Price and Availability
The operator can supply the parts and materials shown in Paragraph 2.C., Parts Necessary for Each
Airplane and Paragraph 2.D., Parts Necessary to Change Spares. As an alternative, operators can
purchase the parts from Boeing Spares. This service bulletin does not show the Boeing price and
supply data.
B. Industry Support Information
Boeing warranty remedies are available for 737 airplanes in warranty as of January 28, 2015. For
inspection labor task hour reimbursement for airplanes in warranty as of that date, send a warranty
claim to Boeing Fleet Support Contracts - Warranty. If the condition described in this service bulletin
is found during the inspection for airplanes in warranty as of that date and additional task hours are
required, send a warranty claim to Boeing Fleet Support Contracts - Warranty. Please refer to this
service bulletin number and reference the airplane variable number(s) in your purchase order. The
warranty remedies will expire eight years from the original issue date of this service bulletin.
C. Parts Necessary for Each Airplane
1. Kits/Parts
None.
2. Parts and Materials Supplied by the Operator
The following parts or materials are necessary if Attachment Hardware discrepancies are found.
Parts and materials in the manuals given in Paragraph 1.J., References, can also be necessary.
Examine operator part and material supply to make sure all necessary parts and materials are
available.
NotesNameQTYPart Number /
Specification
(a)BOLT1BACB30NR4DK14
(a)WASHER1BACW10BP4ACU
(a)WASHER1BACW10BP4APU
(a)NUT1BACN10JD104CD
(a)COTTER PIN1BACP18BC02A04P
(a) This part is per attachment joint. There are 12 attachment joints for Krueger Flap Bullnose
per airplane, six per wing.
3. Parts Modified and Reidentified
None.
4. Parts Removed and Not Replaced
None.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 2: July 25, 2017
45 of 66
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 46

D. Parts Necessary to Change Spares
None.
E. Special Tooling - Price and Availability
None.
F. Special Tooling Necessary to do this Service Bulletin
No special tools or equipment are necessary to do the change in this service bulletin. But, maintenance
and overhaul tools in the manuals given in Paragraph 1.J., References, can be necessary. Examine
operator tool supply to make sure all necessary tools are available.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 2: July 25, 2017
46 of 66
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 47

3.    ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL INFORMATION
KEEP THE WORK AREA, WIRES AND ELECTRICAL BUNDLES CLEAN OF
METAL PARTICLES OR CONTAMINATION WHEN YOU USE TOOLS. UNWANTED
MATERIAL, METAL PARTICLES OR CONTAMINATION CAUGHT IN WIRE
BUNDLES CAN CAUSE DAMAGE TO THE BUNDLES. DAMAGED WIRE BUNDLES
CAN CAUSE SPARKS OR OTHER ELECTRICAL DAMAGE.
CAUTION
NOTE: 1. Manual titles are referred to by acronyms. Refer to Paragraph 1.J., References, for
definition of the acronyms.
2. Obey all of the warnings and cautions given in the specified manual sections.
3. Unless shown differently, these dimensions and tolerances are used:
– Linear dimensions are in inches
– Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus
or minus 0.03 inch
– Tolerance on rivet and bolt edge margin is plus or minus 0.05 inch
– Angular tolerance is plus or minus 2 degrees
– Hole dimensions for standard solid rivets and fasteners are in Structural Repair
Manual (SRM) Chapter 51
– Torque Values:
— Values for structural fasteners are given in 737 Structural Repair Manual,
Chapter 51.
— Values for airframe maintenance tasks are included in Chapter 20 of 737
Aircraft Maintenance Manual (AMM).
— Values for engine maintenance tasks are included in Chapter 70 of 737
Aircraft Maintenance Manual (AMM).
— Non-standard torque values for maintenance tasks are included in the
applicable installation step.
4. Use the approved fastener, process and material substitutions in accordance with
SRM Chapter 51.
5. If the length of any fastener specified in this service bulletin does not meet installation
standards given in SRM Chapter 51, then a fastener of the same specification, or
an approved substitute, with a length which meets the installation standards given
in SRM Chapter 51 may be used. In addition, washers may be installed for fastener
grip length in accordance with SRM Chapter 51. Refer to SOPM 20-50-01 for alternate
full threaded fasteners (screws) needed for installation in this service bulletin.
6. A Detailed Inspection is defined as: An intensive examination of a specific item,
installation, or assembly to detect damage, failure, or irregularity. Available lighting
is normally supplemented with a direct source of good lighting at an intensity deemed
appropriate. Inspection aids such as mirrors, magnifying lenses, etc. may be
necessary. Surface cleaning and elaborate procedures may be required.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 2: July 25, 2017
47 of 66
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 48

7. These work instructions refer to procedures included in other Boeing documents.
When the words "refer to" are used and the operator has an accepted alternative
procedure, the accepted alternative procedure can be used. When the words "in
accordance with" are included in the instruction, the procedure in the Boeing document
must be used.
8. Refer to Appendix A, Appendix B, and Appendix C for logic diagrams. Logic diagrams
are provided as an aid only. Information contained in Paragraph 1.E., Compliance
is the primary source for compliance times. Information in Paragraph 3.B., Work
Instructions is the primary source for tasks required for compliance.
9. The instructions in Paragraph 3.B., Work Instructions and the figures can include
operation of tools or test equipment. Boeing Engineering Tool Drawings, the Illustrated
Tool and Equipment Manual, and the Special Tool and Ground Handling Drawing
Index contain data on versions of the tools or test equipment that you can use. It is
permitted to use replaced tools. It is not permitted to use superseded tools.
10. If it is necessary to remove more parts for access, you can remove those parts. If
you can get access without removing identified parts, it is not necessary to remove
all of the identified parts. Jacking and shoring limitations must be observed.
11. Where the work instructions include installation of a kept part, a new or serviceable
part with the same part number can be installed as an alternative to the kept part.
12. Use of colors in Figures is based on guidance from the ATA e-Business Program
(ATA) iSpec 2200.
13. The compliance times for the actions in Paragraph 3.B., WORK INSTRUCTIONS
are in Paragraph 1.E., Compliance.
14. Some steps in the Work Instructions are labeled as Required for Compliance (RC).
If this service bulletin is mandated by an Airworthiness Directive (AD), then the steps
labeled as RC, including sub-steps under an RC step and any figures identified in
an RC step, must be done to comply with the AD. If a step or sub-step is labeled
"RC Exempt," then the RC requirement is removed from that step or sub-step. An
Alternative Method of Compliance (AMOC) is required for any deviations to RC steps,
including sub-steps and identified figures. Steps not labeled as RC may be deviated
from using accepted methods in accordance with the operator's maintenance or
inspection program without obtaining approval of an AMOC. This is provided that
the RC steps, including sub-steps and identified figures, can still be done as specified,
and the airplane can be put back in an airworthy condition.
B. WORK INSTRUCTIONS
1. Extend Krueger Flaps fully to get access. Refer to 737-600/700/800/900 AMM 27-81-00 as an
accepted procedure.
2. Group 1-2:
RC - Do a one-time detailed inspection for discrepancies in the bullnose attachment hardware on
Krueger Flaps no. 1, 2, 3 and 4 in accordance with FIGURE 1 and FIGURE 2. Discrepancies in
the bullnose attachment hardware include any bolt, washer, castellated nut, or cotter pin
discrepancy.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 2: July 25, 2017
48 of 66
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 49

NOTE: The detailed inspection for discrepancies in the bullnose attachment hardware is
accomplished on the visible area of the attachment hardware, as is installed. It is not
necessary to disassemble the joint to do the detailed inspection.
a. CONDITION 1: ANY ATTACHMENT HARDWARE DISCREPANCY FOUND ON A KRUEGER
FLAP.
(1) Do a detailed inspection of all bullnose Hinge Lugs and Clevis Assemblies on the affected
Krueger Flap, for any crack or any deformation.
(a) CONDITION 1.1: ANY CRACK OR ANY DEFORMATION FOUND ON BULLNOSE
HINGE LUGS OR CLEVIS ASSEMBLIES.
1) Replace affected Krueger Flap. Refer to 737-600/700/800/900 AMM 27-81-11
"LEADING EDGE FLAPS - REMOVAL/INSTALLATION"
As an alternative to replacement of the Krueger flap, replace the cracked or
deformed bullnose hinge lugs or clevis assemblies on the flap. Refer to CMM
57-56-33 or CMM 57-56-44 as an accepted procedure to replace cracked
bullnose hinge lugs or clevis assemblies on the existing Krueger flap.
(b) CONDITION 1.2: NO CRACK OR DEFORMATION FOUND ON BULLNOSE HINGE
LUGS OR CLEVIS ASSEMBLIES.
1) Replace discrepant Krueger Flap bullnose attachment hardware in accordance
with FIGURE 3 or FIGURE 4.
b. CONDITION 2: NO ATTACHMENT HARDWARE DISCREPANCY FOUND ON A KRUEGER
FLAP.
(1) No Further Action Required.
3. RC - Determine if any Krueger Flap no. 1, 2, 3, or 4 has been replaced and if any replaced Krueger
Flap has accomplished this service bulletin.
NOTE: It is acceptable to review maintenance records to determine if this service bulletin was
accomplished on the replaced Krueger flap. If the accomplishment of this service bulletin
is not known or cannot be positively verified by maintenance records, assume that the
accomplishment of this service bulletin was not done on the replaced Krueger flap.
NOTE: Any Krueger Flap 1, 2, 3, or 4 originally installed on delivered Group 3 airplanes has had
the intent of this service bulletin incorporated in production. These Krueger Flaps can be
considered as having accomplished this service bulletin.
a. CONDITION 3: AIRPLANES WITH ANY KRUEGER FLAP NO. 1, 2, 3, OR 4 REPLACED
WITH A KRUEGER FLAP THAT HAS ACCOMPLISHED THIS SERVICE BULLETIN.
(1) No further action required.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 2: July 25, 2017
49 of 66
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 50

b. CONDITION 4: AIRPLANES WITH ANY KRUEGER FLAP NO. 1, 2, 3, OR 4 REPLACED
WITH A KRUEGER FLAP THAT HAS NOT ACCOMPLISHED THIS SERVICE BULLETIN
OR WITH A KRUEGER FLAP WHERE THE ACCOMPLISHMENT OF THIS SERVICE
BULLETIN IS NOT KNOWN.
(1) Do a one-time detailed inspection for discrepancies in the bullnose attachment hardware
of the replaced Krueger Flap in accordance with FIGURE 1 and FIGURE 2. Discrepancies
in the bullnose attachment hardware include any bolt, washer, castellated nut, or cotter
pin discrepancy.
NOTE: The detailed inspection for discrepancies in the bullnose attachment hardware
is accomplished on the visible area of the attachment hardware, as is installed.
It is not necessary to disassemble the joint to do the detailed inspection.
(a) CONDITION 5: ANY ATTACHMENT HARDWARE DISCREPANCY FOUND ON A
KRUEGER FLAP.
1) Do a detailed inspection of all bullnose hinge lugs and clevis assemblies on the
affected Krueger Flap, for any crack or any deformation.
a) CONDITION 5.1: ANY CRACK OR ANY DEFORMATION FOUND ON
BULLNOSE HINGE LUGS OR CLEVIS ASSEMBLIES.
{1} Replace affected Krueger Flap. Refer to 737-600/700/800/900 AMM
27-81-11 "LEADING EDGE FLAPS - REMOVAL/INSTALLATION"
As an alternative to replacement of the Krueger Flap, replace the
cracked or deformed bullnose hinge lugs or clevis assemblies on the
flap. Refer to CMM 57-56-33 or CMM 57-56-44 as an accepted
procedure to replace cracked bullnose hinge lugs or clevis assemblies
on the existing Krueger flap.
b) CONDITION 5.2: NO CRACK OR DEFORMATION FOUND ON BULLNOSE
HINGE LUGS OR CLEVIS ASSEMBLIES.
{1} Replace discrepant Krueger Flap bullnose attachment hardware in
accordance with FIGURE 3 or FIGURE 4.
(b) CONDITION 6: NO ATTACHMENT HARDWARE DISCREPANCY FOUND ON A
KRUEGER FLAP.
1) No Further Action Required.
4. Put the airplane back to a serviceable condition.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 2: July 25, 2017
50 of 66
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 51 (OCR)

BOEING SERVICE BULLETIN 737-57A1327
ALERT  ALERT
18 8  LE STA  206.32
LE STA
190.85  LE STA  LE STA
180.52  166.32
LE STA
158.82
INBD
NO. 1 KRUEGER FLAP
2483910
FIGURE 1: LEFT WING - KRUEGER FLAP 1 AND 2 BULLNOSE ATTACHMENT HARDWARE ONE-TIME
INSPECTION
(SHEET 1 OF 3)
Original Issue: May 20, 2016
Revision 2 July 25, 2017  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  737-57A1327
Work - See page 1 for details.  51 of 66

### Page 52 (OCR)

BOEING SERVICE BULLETIN 737-57A1327
ALERT  ALERT
LE STA
150.82
LE STA
104.52
INBD
NO. 2 KRUEGER FLAP
BULLNOSE  CLEVIS  BULLNOSE  1) COTTER PIN LEGS
HINGE LUG  ASSEMBLY HINGE LUG
1 COTTER PIN HEAD
CLEVIS  INBD
A-A  2483919
FIGURE 1: LEFT WING - KRUEGER FLAP 1 AND 2 BULLNOSE ATTACHMENT HARDWARE ONE-TIME
INSPECTION
(SHEET 2 OF 3)
Original Issue: May 20, 2016
Revision 2 July 25, 2017  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  737-57A1327
Work - See page 1 for details.  52 of 66

### Page 53

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for each attachment location shown in this figure.
More DataQtyIdentificationNameTaskStep
Do a Detailed Inspec-
tion for discrepan-
cies.(d)(e)
1BACP18BC02A04PCOTTER PINInspect1
Do a Detailed Inspec-
tion for discrepan-
cies.(a)(e)
1BACN10JD104CDCASTELLATED NUTInspect2
Do a Detailed Inspec-
tion for discrepan-
cies.(b)(e)
1BACW10BP4APUWASHERInspect3
Do a Detailed Inspec-
tion for discrepan-
cies.(b)(e)
1BACW10BP4ACUWASHERInspect4
Do a Detailed Inspec-
tion for discrepan-
cies.(c)(e)
1BACB30NR4DK14BOLTInspect5
(a) Castellated nut discrepancies include missing, loose, worn, cracked, or damaged castellated nuts. Damage
is defined as, but not limited to, any dent(s), nick(s), or gouge(s).
(b) Washer discrepancies include missing, loose, worn, or damaged washers. Damage is defined as, but not
limited to, any dent(s), nick(s), or gouge(s).
(c) Bolt discrepancies include bolts that do not meet end protrusion for minimum threads, missing, cracked,
loose, or damaged bolts. Damage is defined as, but not limited to, any dent(s), nick(s), or gouge(s).
(d) Cotter pin discrepancies include missing cotter pins and cotter pins with head protrusion and cotter pin
leg bend orientation that do not match SOPM 20-50-02. Refer to SOPM 20-50-02 as an accepted procedure
for installation of cotter pins.
(e) The detailed inspection for discrepancies in the bullnose attachment hardware is accomplished on the
visible area of the attachment hardware, as is installed. It is not necessary to disassemble the joint to do
the detailed inspection.
FIGURE 1: LEFT WING - KRUEGER FLAP 1 AND 2 BULLNOSE ATTACHMENT HARDWARE ONE-TIME
INSPECTION
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 2 July 25, 2017
53 of 66
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 54 (OCR)

BOEING SERVICE BULLETIN 737-57A1327
ALERT  ALERT
LE STA  LE STA
LE STA  206.32  218.88
LE STA  LE STA  190.85
LE STA  166.32  180.52
158.82
INBD
NO. 4 KRUEGER FLAP
2483921
FIGURE 2: RIGHT WING - KRUEGER FLAP 3 AND 4 BULLNOSE ATTACHMENT HARDWARE ONE-TIME
INSPECTION
(SHEET 1 OF 3)
Original Issue: May 20, 2016
Revision 2 July 25, 2017  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  737-57A1327
Work - See page 1 for details.  54 of 66

### Page 55 (OCR)

BOEING SERVICE BULLETIN 737-57A1327
ALERT  ALERT
LE STA
150.82
LE STA
104.52
INBD
NO. 3 KRUEGER FLAP
BULLNOSE  CLEVIS  BULLNOSE
COTTER PIN LEGS  HINGE LUG  ASSEMBLY HINGE LUG
COTTER PIN HEAD
CLEVIS  INBD
A-A  2483928
FIGURE 2: RIGHT WING - KRUEGER FLAP 3 AND 4 BULLNOSE ATTACHMENT HARDWARE ONE-TIME
INSPECTION
(SHEET 2 OF 3)
Original Issue: May 20, 2016
Revision 2 July 25, 2017  Export Controlled ECCN: 9E991 - BOEING  737-57A1327
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  55 of 66

### Page 56

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for each attachment location shown in this figure.
More DataQtyIdentificationNameTaskStep
Do a Detailed Inspec-
tion for discrepan-
cies.(d)(e)
1BACP18BC02A04PCOTTER PINInspect1
Do a Detailed Inspec-
tion for discrepan-
cies.(a)(e)
1BACN10JD104CDCASTELLATED NUTInspect2
Do a Detailed Inspec-
tion for discrepan-
cies.(b)(e)
1BACW10BP4APUWASHERInspect3
Do a Detailed Inspec-
tion for discrepan-
cies.(b)(e)
1BACW10BP4ACUWASHERInspect4
Do a Detailed Inspec-
tion for discrepan-
cies.(c)(e)
1BACB30NR4DK14BOLTInspect5
(a) Castellated nut discrepancies include missing, loose, worn, cracked, or damaged castellated nuts. Damage
is defined as, but not limited to, any dent(s), nick(s), or gouge(s).
(b) Washer discrepancies include missing, loose, worn, or damaged washers. Damage is defined as, but not
limited to, any dent(s), nick(s), or gouge(s).
(c) Bolt discrepancies include bolts that do not meet end protrusion for minimum threads, missing, cracked,
loose, or damaged bolts. Damage is defined as, but not limited to, any dent(s), nick(s), or gouge(s).
(d) Cotter pin discrepancies include missing cotter pins and cotter pins with head protrusion and cotter pin
leg bend orientation that do not match SOPM 20-50-02. Refer to SOPM 20-50-02 as an accepted procedure
for installation of cotter pins.
(e) The detailed inspection for discrepancies in the bullnose attachment hardware is accomplished on the
visible area of the attachment hardware, as is installed. It is not necessary to disassemble the joint to do
the detailed inspection.
FIGURE 2: RIGHT WING - KRUEGER FLAP 3 AND 4 BULLNOSE ATTACHMENT HARDWARE ONE-TIME
INSPECTION
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 2 July 25, 2017
56 of 66
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 57 (OCR)

BOEING SERVICE BULLETIN 737-57A1327
ALERT  ALERT
18 8  LE STA  206.32
LE STA
190.85  LE STA  LE STA
180.52  166.32
LE STA
158.82
INBD
NO. 1 KRUEGER FLAP
2487991
FIGURE 3: LEFT WING - KRUEGER FLAP 1 AND 2 BULLNOSE ATTACHMENT HARDWARE INSTALLATION
(SHEET 1 OF 3)
Original Issue: May 20, 2016
Revision 2 July 25, 2017  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  737-57A1327
Work - See page 1 for details.  57 of 66

### Page 58 (OCR)

BOEING SERVICE BULLETIN 737-57A1327
ALERT  ALERT
LE STA
150.82
LE STA
104.52
INBD
NO. 2 KRUEGER FLAP
BULLNOSE  CLEVIS  BULLNOSE  (5) COTTER PIN LEGS
HINGE LỤG  ASSEMBLY HINGE LUG
(5) COTTER PIN HEAD
CLEVIS  INBD
A-A  2528090
FIGURE 3: LEFT WING - KRUEGER FLAP 1 AND 2 BULLNOSE ATTACHMENT HARDWARE INSTALLATION
(SHEET 2 OF 3)
Original Issue: May 20, 2016
Revision 2 July 25, 2017  Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright © Unpublished  737-57A1327
Work - See page 1 for details.  58 of 66

### Page 59

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for each attachment location shown in this figure.
More DataQtyIdentificationNameTaskStep
(a)1BACW10BP4ACUWASHERInstall (New)1
(a)1BACB30NR4DK14BOLTInstall (New)2
(a)1BACW10BP4APUWASHERInstall (New)3
(a)1BACN10JD104CDCASTELLATED NUTInstall (New)4
Refer to SOPM 20-
50-02 as an accept-
ed procedure.
1BACP18BC02A04PCOTTER PINInstall (New)5
(a) Install new part if part was discrepant, or install kept part if part is not discrepant. Refer to CMM 57-56-33
and SOPM 20-50-02 as an accepted procedure.
FIGURE 3: LEFT WING - KRUEGER FLAP 1 AND 2 BULLNOSE ATTACHMENT HARDWARE INSTALLATION
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 2 July 25, 2017
59 of 66
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 60 (OCR)

BOEING SERVICE BULLETIN 737-57A1327
ALERT  ALERT
LE STA  LE STA
LE STA  206.32  218.88
LE STA  LE STA  190.85
LE STA  166.32  180.52
158.82
INBD
NO. 4 KRUEGER FLAP
2487992
FIGURE 4: RIGHT WING - KRUEGER FLAP 3 AND 4 BULLNOSE ATTACHMENT HARDWARE
INSTALLATION
(SHEET 1 OF 3)
Original Issue: May 20, 2016
Revision 2 July 25, 2017  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  737-57A1327
Work - See page 1 for details.  60 of 66

The text continues at https://openairdocs.org/service-documents/boeing/737-57a1327/file/12bdd8628f18.md?from=61

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
