# Boeing Alert Service Bulletin 737-57A1327: Revision 1

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2016-9112; AD 2017-16-05 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Alert Service Bulletin 737-57A1327](https://openairdocs.org/service-documents/boeing/737-57a1327.md)
- Title as filed: SB 737-57A1327, Rev. 1 - NG Krueger flap inspection
- Pages: 51
- PDF: https://openairdocs.org/files/sha256/55/14/551456bf04e665f018060b53f1a683d1f7854ddb3b65e2bb22412ca143b5af72
- Page: https://openairdocs.org/service-documents/boeing/737-57a1327/file/551456bf04e6

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Commercial 
Airplanes
737
Service Bulletin
ALERT
Number: 737-57A1327
Original Issue: May 20, 2016
Revision 1: September 28, 2016
ATA System: 5740
SUBJECT: WINGS - Leading Edge And Leading Edge Devices - Krueger Flap Inspection
Export of this technology is controlled under the United States Export Administration Regulations (EAR) (15
CFR 300-774). An export license may be required before it is used for development, production or use by foreign
persons from specific countries. The controller of this data has the individual responsibility to abide by all export
laws.
9E991ECCN:
BOEING PROPRIETARY, CONFIDENTIAL AND/OR TRADE SECRET
Copyright © 2016 Boeing.
Unpublished Work. All Rights Reserved.
Treatment of this document and its content is governed by contract with Boeing. Rights to use this document
are licensed on a per aircraft basis and such rights may not be transferable. For more information, contact The
Boeing Company.
Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner,
BBJ, DC-8, DC-9, DC-10, KC-10, KC-46, KDC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8, Poseidon and
Boeing liveries are all trademarks owned by The Boeing Company; and no trademark license is granted in
connection with this document unless provided in writing by Boeing.
Original Issue: May 20, 2016
737-57A1327Revision 1: September 28, 2016
1 of 51
3.0

### Page 2

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 1: September 28, 2016
2 of 51
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT
BLANK PAGE

### Page 3

Table of Contents
Revision Transmittal Sheet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1. PLANNING INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
A. Effectivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
1. Airplanes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2. Spares Affected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
B. Concurrent Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
C. Reason . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
D. Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
E. Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
F. Approval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
G. Manpower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
H. Weight and Balance Changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
I. Electrical Load Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
J. References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
1. Existing Data: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
2. Data Supplied with this Service Bulletin: . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
3. Installation Drawings Used in the Preparation of this Service Bulletin: . . . . . . . . . . . 31
K. Publications Affected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
L. Interchangeability and Intermixability of Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
M. Software Accomplishment Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
2. MATERIAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
A. Material - Price and Availability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
B. Industry Support Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
C. Parts Necessary for Each Airplane . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
1. Kits/Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
2. Parts and Materials Supplied by the Operator . . . . . . . . . . . . . . . . . . . . . . . . 33
3. Parts Modified and Reidentified . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
4. Parts Removed and Not Replaced . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
D. Parts Necessary to Change Spares . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
E. Special Tooling - Price and Availability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
F. Special Tooling Necessary to do this Service Bulletin . . . . . . . . . . . . . . . . . . . . . . . 34
3. ACCOMPLISHMENT INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
A. GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
B. WORK INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
FIGURE 1: LEFT WING - KRUEGER FLAP 1 AND 2 BULLNOSE ATTACHMENT HARDWARE ONE-TIME
INSPECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
FIGURE 2: RIGHT WING - KRUEGER FLAP 3 AND 4 BULLNOSE ATTACHMENT HARDWARE ONE-TIME
INSPECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
FIGURE 3: LEFT WING - KRUEGER FLAP 1 AND 2 BULLNOSE ATTACHMENT HARDWARE
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
FIGURE 4: RIGHT WING - KRUEGER FLAP 3 AND 4 BULLNOSE ATTACHMENT HARDWARE
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
APPENDIX A: LOGIC DIAGRAM FOR PARAGRAPH 1.E. COMPLIANCE: TABLE 1: KRUEGER FLAP
BULLNOSE ATTACHMENT HARDWARE ONE-TIME INSPECTION. . . . . . . . . . . . 50
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 1: September 28, 2016
3 of 51
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 4

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 1: September 28, 2016
4 of 51
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT
BLANK PAGE

### Page 5

Commercial 
Airplanes
737
Service Bulletin
ALERT
Revision Transmittal SheetNumber: 737-57A1327Original Issue: May 20, 2016
Revision 1: September 28, 2016
ATA System: 5740
SUBJECT: WINGS - Leading Edge And Leading Edge Devices - Krueger Flap Inspection
This revision includes all pages of the service bulletin.
COMPLIANCE INFORMATION RELATED TO THIS REVISION
The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to this service
bulletin. The Airworthiness Directive will make the compliance tasks and times given in this service bulletin
mandatory.
Effects of this Revision on airplanes on which Original Issue was previously done:
None.
REASON FOR REVISION
This revision is sent to give a clarification that a removal of the attachment hardware is not necessary when
accomplishing the detailed inspection of the hardware. Also this revision changes illustrations to show correct
orientation of the attachment hardware and gives minor changes on terminology and general references.
The data given in Information Notice 737-57A1327 IN 01 is included in this revision.
These sections were changed:
1. In Summary, Action, changed the terminology to "any crack" and removed the terminology "if required".
2. In Summary, Effectivity, added reference for spares affected.
3. In Summary, Material Information, added Operator supplied parts/materials reference.
4. In Paragraph 1.C., Reason, added Fleet Team Digest (FTD) and Service Related Problem (SRP)
information. Added reason for the revision.
5. In Paragraph 1.D., Description, changed the terminology to "any crack" and removed the terminology
"if required". Added effects of this revision.
6. In Paragraph 1.E., Compliance, updated existing reference to refer to Table 1.
7. In Paragraph 1.G., Manpower, added a title to the manpower table.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 1: September 28, 2016
5 of 51

### Page 6

8. In Paragraph 1.J.3., Installation Drawings Used in the Preparation of this Service Bulletin, updated
drawing title and removed drawing.
9. In Paragraph 2.C.2., Parts and Materials Supplied by the Operator, updated the footnote.
10. In Paragraph 3.B., Work Instructions, added a note to do the detailed inspection without removal of
the attachment hardware and removed the terminology "as applicable". Updated existing note to put
the airplane back to a serviceable condition.
11. In FIGURE 1 and FIGURE 2, updated illustrations, added a footnote, and updated footnote terminology.
12. In FIGURE 3 and FIGURE 4, updated illustrations and added an SOPM reference for cotter pin
installation.
13. In APPENDIX A, updated logic diagram to be consistent with the compliance table.
Vertical lines are put on the left edge of each page, except in Paragraph 1.A., Effectivity and format changes,
to show the location of all content changes.
Pages with no vertical lines have no changes.
REVISION HISTORY
May 20, 2016Original Issue:
September 28, 2016Revision 1:
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 1: September 28, 2016
6 of 51
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 7

Commercial 
Airplanes
737
Service Bulletin
ALERT
SummaryNumber: 737-57A1327Original Issue: May 20, 2016
Revision 1: September 28, 2016
ATA System: 5740
SUBJECT: WINGS - Leading Edge And Leading Edge Devices - Krueger Flap Inspection
THIS DOCUMENT IS SENT TO THE OPERATORS OF RECORD OF THE AIRPLANES SHOWN IN
PARAGRAPH 1.A., EFFECTIVITY. IF AN AIRPLANE HAS BEEN LEASED OR SOLD, SEND THIS DOCUMENT
TO THE NEW OPERATOR. IF APPLICABLE SPARES HAVE BEEN SOLD, SEND THIS DOCUMENT TO THE
NEW OWNER.
CONCURRENT REQUIREMENTS
None.
BACKGROUND
The Bullnose of a 737-800 Krueger Flap departed an airplane during taxi and caused damage to the wing
structure and part of the thrust reverser. There have been six (6) other in-service reports of missing Bullnose
attachment hardware resulting in a Bullnose droop condition but no departure of the part from the airplane. If
this service bulletin is not accomplished, the Krueger Flap Bullnose could depart the airplane during flight, which
could damage empennage structure leading to inability to maintain continued safe flight and landing.
Boeing Fleet Team Digest (FTD) 737NG FTD 57-15003 is related to this service bulletin.
Boeing Service Related Problem (SRP) 737NG-57-0283 is related to this service bulletin.
This table is provided to operators for planning purposes only. Refer to the applicable sections for more
information.
ReferenceAffectedPlanning Data
Paragraph 1.A.2., Spares AffectedYesSpares Affected
Paragraph 1.E., Compliance and Paragraph
1.F., Approval
YesAD Related
Paragraph 1.H., Weight and Balance ChangesNoWeight and Balance Change
Paragraph 1.I., Electrical Load DataNoElectrical Load Changed
Paragraph 1.K., Publications AffectedNoPublications Affected
Paragraph 1.K., Publications AffectedNoAirplane Flight Operations Affected (Flight Crew
Operations Manual and/or FAA Approved Air-
plane Flight Manual)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 1: September 28, 2016
7 of 51

### Page 8

ReferenceAffectedPlanning Data
Paragraph 2.C.1., Kits/PartsNoKits/Parts Required
Paragraph 2.C.2., Parts and Materials Supplied
by the Operator
YesOperator Supplied Parts/Material
Paragraph 2.F., Special Tooling Necessary to
do this Service Bulletin
NoSpecial Tooling Required
ACTION
Get access and do a one-time detailed inspection for discrepancies in the Bullnose attachment hardware of
Krueger Flaps no. 1, 2, 3 and 4. If any discrepancy is found, do a secondary detailed inspection for any crack
or any deformation and either replace the discrepant hardware or Krueger Flap.
EFFECTIVITY
737-600/700/700C/800/900/900ER Airplane(s). Refer to Paragraph 1.A.1., Airplanes, for the list of affected
airplanes.
Refer to Paragraph 1.A.2., Spares Affected, for the list of affected components.
COMPLIANCE
The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to this service
bulletin. The Airworthiness Directive will make the compliance tasks and times given in this service bulletin
mandatory.
Refer to Paragraph 1.E., Compliance.
INDUSTRY SUPPORT INFORMATION
Boeing warranty remedies are available for airplanes in warranty as of January 28, 2015 Please refer to Paragraph
2.B., Industry Support Information. The warranty remedies will expire eight years from the original issue date of
this service bulletin.
MANPOWER
Elapsed HoursTotal Task HoursAirplanes
2.802.80Group 1
MATERIAL INFORMATION
Operator Supplied Parts/Materials.
Refer to Paragraph 2.A., Material - Price and Availability.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 1: September 28, 2016
8 of 51
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 9 (OCR)

BOEING SERVICE BULLETIN 737-57A1327
ALERT  ALERT
LE STA  LE STA
218.88  206.32  LE STA
190.85  LE STA
180.52  LE STA
166.32 LE STA
158.82
INBD
VO. 1 KRUEGER FLAP IS SHOWN
NO. 4 KRUEGER FLAP IS OPPOSITE
LE STA
150.82
DO A ONE-TIME DETAILED
INSPECTION FOR DISCREPANCIES
IN THE ATTACHMENT HARDWARE.
LE STA
104.52
NBD
DO A ONE-TIME DETAILED
NO. 2 KRUEGER FLAP IS SHOWN,  INSPECTION FOR DISCREPANCIES
NO. 3 KRUEGER FLAP IS OPPOSITE  IN THE ATTACHMENT HARDWARE.  2483896
Original Issue: May 20, 2016
Revision 1: September 28, 2016  Export Controlled ECCN: 9E991 - BOEING  737-57A1327
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  9 of 51

### Page 10

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 1: September 28, 2016
10 of 51
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT
BLANK PAGE

### Page 11

Commercial 
Airplanes
737
Service Bulletin
ALERT
Number: 737-57A1327
Original Issue: May 20, 2016
Revision 1: September 28, 2016
ATA System: 5740
SUBJECT: WINGS - Leading Edge And Leading Edge Devices - Krueger Flap Inspection
THIS DOCUMENT IS SENT TO THE OPERATORS OF RECORD OF THE AIRPLANES SHOWN IN
PARAGRAPH 1.A., EFFECTIVITY. IF AN AIRPLANE HAS BEEN LEASED OR SOLD, SEND THIS DOCUMENT
TO THE NEW OPERATOR. IF APPLICABLE SPARES HAVE BEEN SOLD, SEND THIS DOCUMENT TO THE
NEW OWNER.
1.    PLANNING INFORMATION
A. Effectivity
1. Airplanes
This service bulletin is applicable to 737-600, -700, -700C, -800, -900, -900ER Airplanes line
numbers 1-5502 in 1 Group. The Variable Numbers and Group Information for the applicable
airplanes is given below.
Refer to Service Bulletin Index D6-19567 Part 3 for Airplane Variable Number, Line Number, and
Serial Number data.
DESCRIPTIONCONFIGURATIONGROUP
737-600, -700, -700C, -800, -900, -900ER Airplanes-1
Airplane Models:
737-600, 737-700, 737-700C, 737-800, 737-900, 737-900ER
GroupVariable Number
1YA001 - YA099
1YA101 - YA199
1YA201 - YA211
1YA221
1YA231 - YA242
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 1: September 28, 2016
11 of 51

### Page 12

GroupVariable Number
1YA251 - YA256
1YA271 - YA272
1YA291
1YA301 - YA302
1YA311 - YA314
1YA321 - YA323
1YA336 - YA345
1YA351
1YA356 - YA357
1YA366 - YA367
1YA371 - YA377
1YA501 - YA536
1YA541 - YA552
1YA571 - YA578
1YA601 - YA615
1YA621 - YA622
1YA626 - YA631
1YA635 - YA636
1YA641 - YA642
1YA645 - YA650
1YA656 - YA659
1YA666 - YA667
1YA671 - YA672
1YA681 - YA691
1YA701 - YA710
1YA721 - YA722
1YA731 - YA734
1YA751 - YA756
1YA801 - YA803
1YA809
1YA811 - YA814
1YA831 - YA835
1YA841 - YA862
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 1: September 28, 2016
12 of 51
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 13

GroupVariable Number
1YA881 - YA882
1YA891 - YA892
1YA961 - YA978
1YB001 - YB006
1YB101 - YB132
1YB151 - YB153
1YB156 - YB158
1YB161 - YB164
1YB171 - YB172
1YB181 - YB184
1YB201 - YB208
1YB271
1YB276
1YB301 - YB310
1YB371 - YB392
1YB501 - YB502
1YB521 - YB526
1YB541 - YB544
1YB551
1YB561 - YB598
1YB601 - YB636
1YB651
1YB656
1YB671 - YB672
1YB851 - YB863
1YB871 - YB874
1YB881 - YB893
1YB901 - YB903
1YB911
1YB961 - YB975
1YB981
1YB986 - YB998
1YC001 - YC030
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 1: September 28, 2016
13 of 51
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 14

GroupVariable Number
1YC051 - YC084
1YC091 - YC095
1YC101 - YC104
1YC111 - YC113
1YC121
1YC126 - YC127
1YC136 - YC141
1YC146 - YC147
1YC151 - YC156
1YC166 - YC171
1YC176 - YC179
1YC186 - YC190
1YC201 - YC203
1YC206 - YC207
1YC301 - YC305
1YC321 - YC387
1YC391 - YC394
1YC396
1YC401 - YC417
1YC421 - YC422
1YC426 - YC428
1YC436 - YC439
1YC441 - YC448
1YC451 - YC455
1YC459
1YC461 - YC467
1YC471 - YC499
1YC501 - YC526
1YC571 - YC583
1YC587 - YC589
1YC591 - YC593
1YC601 - YC655
1YC681 - YC696
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 1: September 28, 2016
14 of 51
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 15

GroupVariable Number
1YC701 - YC715
1YC720 - YC725
1YC727 - YC752
1YC761 - YC770
1YC781 - YC793
1YC801 - YC892
1YC901 - YC907
1YC921 - YC922
1YC931 - YC932
1YC941 - YC951
1YC971 - YC978
1YC981 - YC983
1YD001 - YD007
1YD021 - YD025
1YD041 - YD057
1YD081 - YD084
1YD101 - YD117
1YD121 - YD126
1YD151 - YD159
1YD171 - YD172
1YD201 - YD203
1YD206 - YD209
1YD216 - YD219
1YD251 - YD254
1YD256 - YD257
1YD261
1YD301 - YD334
1YD391
1YD401 - YD410
1YD412 - YD422
1YD481 - YD485
1YD491 - YD499
1YD501 - YD512
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 1: September 28, 2016
15 of 51
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 16

GroupVariable Number
1YD531 - YD535
1YD541 - YD547
1YD561 - YD564
1YD571 - YD572
1YD591 - YD595
1YD601 - YD612
1YD651 - YD655
1YE001 - YE020
1YE051
1YE101 - YE109
1YE151 - YE157
1YE171 - YE172
1YE201 - YE206
1YE301 - YE305
1YE321 - YE326
1YE371 - YE383
1YF001 - YF011
1YF021 - YF049
1YF051 - YF080
1YF086 - YF087
1YF106 - YF107
1YF111 - YF114
1YF116 - YF119
1YF121 - YF132
1YF176 - YF178
1YF191 - YF192
1YF201 - YF276
1YF401 - YF402
1YF431 - YF432
1YF436 - YF437
1YF441 - YF442
1YF451 - YF460
1YF501 - YF599
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 1: September 28, 2016
16 of 51
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 17

GroupVariable Number
1YF601 - YF682
1YF701 - YF707
1YF801 - YF805
1YF831 - YF832
1YF836 - YF838
1YF871 - YF872
1YF901 - YF905
1YF921 - YF928
1YF951 - YF954
1YG001 - YG044
1YG061 - YG064
1YG066 - YG089
1YG091 - YG099
1YG101 - YG104
1YG111 - YG114
1YG116 - YG143
1YG201 - YG205
1YG211 - YG214
1YG221 - YG224
1YG251 - YG252
1YG501 - YG514
1YG601 - YG602
1YG701
1YG711
1YH001 - YH012
1YH031 - YH055
1YH071 - YH080
1YH101 - YH132
1YH201 - YH202
1YH206 - YH207
1YH301 - YH306
1YH321 - YH322
1YH501 - YH542
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 1: September 28, 2016
17 of 51
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 18

GroupVariable Number
1YH551 - YH594
1YH601 - YH606
1YH611 - YH620
1YH631 - YH632
1YH636 - YH637
1YH641
1YH681 - YH683
1YH701 - YH728
1YH751 - YH754
1YH801 - YH843
1YH901 - YH905
1YH911 - YH915
1YH951 - YH952
1YJ001 - YJ013
1YJ021
1YJ471 - YJ480
1YJ501 - YJ517
1YJ531 - YJ579
1YJ591 - YJ599
1YJ631 - YJ632
1YJ671 - YJ694
1YJ801 - YJ867
1YJ871 - YJ880
1YJ901 - YJ904
1YJ908 - YJ929
1YJ931 - YJ937
1YJ941 - YJ956
1YJ961
1YJ976 - YJ977
1YK001 - YK007
1YK101 - YK104
1YK111 - YK112
1YK121 - YK122
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 1: September 28, 2016
18 of 51
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 19

GroupVariable Number
1YK131 - YK133
1YK136 - YK139
1YK141 - YK142
1YK146 - YK148
1YK151 - YK154
1YK161 - YK167
1YK171
1YK176 - YK177
1YK186
1YK191
1YK196
1YK201 - YK202
1YK301 - YK314
1YK321 - YK340
1YK361 - YK378
1YK401 - YK406
1YK426 - YK427
1YK431 - YK450
1YK456 - YK467
1YK471 - YK473
1YK476
1YK480 - YK487
1YK491 - YK493
1YK495 - YK499
1YK511 - YK516
1YK521 - YK530
1YK551 - YK571
1YK576 - YK577
1YK580 - YK585
1YK601 - YK602
1YK606 - YK607
1YK611 - YK616
1YK621 - YK634
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 1: September 28, 2016
19 of 51
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 20

GroupVariable Number
1YK641 - YK644
1YK651 - YK665
1YK671 - YK672
1YK676 - YK677
1YK681 - YK686
1YK691
1YK695 - YK699
1YK701 - YK713
1YK716 - YK719
1YK721 - YK741
1YK751 - YK770
1YK776 - YK778
1YK781 - YK785
1YK791 - YK792
1YK796 - YK797
1YK801 - YK899
1YK901 - YK912
1YK918 - YK919
1YK921 - YK929
1YK941 - YK999
1YL001 - YL005
1YL011 - YL016
1YL021 - YL024
1YL051 - YL052
1YL056 - YL057
1YL061
1YL066 - YL069
1YL076 - YL077
1YL101 - YL137
1YL201 - YL237
1YL241 - YL242
1YL271 - YL272
1YL281 - YL284
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 1: September 28, 2016
20 of 51
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 21

GroupVariable Number
1YL301 - YL303
1YL311 - YL314
1YL316 - YL321
1YL351 - YL353
1YL371 - YL374
1YL401
1YL421 - YL429
1YL431 - YL444
1YL461 - YL478
1YL501 - YL509
1YL531 - YL534
1YL541 - YL551
1YL561 - YL579
1YL591 - YL598
1YL601 - YL606
1YL611 - YL612
1YL616 - YL617
1YL621
1YL626
1YL631 - YL634
1YL636 - YL637
1YL661 - YL664
1YL676 - YL691
1YL696 - YL697
1YL701 - YL707
1YL731
1YL751 - YL752
1YL756 - YL757
1YL761 - YL780
1YL796 - YL797
1YL801 - YL815
1YL901 - YL910
1YL921 - YL940
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 1: September 28, 2016
21 of 51
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 22

GroupVariable Number
1YL951 - YL968
1YM101 - YM103
1YM201 - YM244
1YM251 - YM299
1YM301 - YM399
1YM401 - YM415
1YM471
1YM481 - YM484
1YM501 - YM515
1YM521 - YM522
1YM541
1YM551 - YM553
1YM571 - YM572
1YM581 - YM582
1YM591 - YM599
1YM631 - YM634
1YM641 - YM652
1YM671 - YM674
1YM691 - YM699
1YM701 - YM710
1YM761 - YM765
1YM771 - YM779
1YN001 - YN016
1YN021 - YN024
1YN061
1YN071 - YN082
1YN091 - YN092
1YN101 - YN112
1YN121
1YN126
1YN201 - YN202
1YN211 - YN219
1YN231 - YN236
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 1: September 28, 2016
22 of 51
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 23

GroupVariable Number
1YN261
1YN501
1YN531 - YN534
1YN551 - YN564
1YN581 - YN585
1YN591 - YN592
1YN601 - YN606
1YN651 - YN653
1YN701 - YN702
1YN741 - YN746
1YN756
1YQ001 - YQ003
1YQ011 - YQ021
1YQ026 - YQ029
1YQ036 - YQ045
1YQ201 - YQ207
1YQ231
1YQ241 - YQ251
1YQ281 - YQ284
1YQ291 - YQ296
1YQ301 - YQ302
1YQ321 - YQ324
1YQ331 - YQ334
1YQ346 - YQ347
1YQ351
1YQ401 - YQ403
1YQ451 - YQ454
1YQ456
1YQ461
1YQ471
1YQ501 - YQ519
1YR001 - YR043
1YR051 - YR087
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 1: September 28, 2016
23 of 51
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 24

GroupVariable Number
1YR091 - YR098
1YR101 - YR105
1YR111 - YR124
1YR126 - YR144
1YR166 - YR182
1YR186 - YR198
1YR201 - YR204
1YR231 - YR294
1YR296 - YR297
1YR301 - YR334
1YR338 - YR341
1YR361 - YR366
1YR371 - YR373
1YR376
1YR381 - YR382
1YR386 - YR388
1YR391
1YR396 - YR398
1YR401 - YR405
1YR411 - YR413
1YR416 - YR418
1YR421 - YR424
1YR426 - YR455
1YR457 - YR499
1YR501 - YR506
1YR511 - YR520
1YR526 - YR544
1YR546 - YR551
1YR556 - YR562
1YR571 - YR582
1YR591 - YR592
1YR601 - YR605
1YR616 - YR658
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 1: September 28, 2016
24 of 51
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 25

GroupVariable Number
1YR661 - YR663
1YR671 - YR672
1YR676 - YR678
1YR681 - YR682
1YR701 - YR769
1YR771 - YR799
1YR801 - YR816
1YR831 - YR838
1YR841 - YR897
1YR901 - YR903
1YR931 - YR934
1YR938 - YR944
1YR951 - YR970
1YR981 - YR996
1YS001 - YS002
1YS006 - YS009
1YS031 - YS032
1YS051 - YS073
1YS101 - YS120
1YS126 - YS137
1YS151 - YS160
1YS166 - YS194
1YS196 - YS197
1YS201 - YS209
1YS221 - YS225
1YS231 - YS236
1YS271 - YS286
1YS301 - YS334
1YS351 - YS365
1YS371 - YS374
1YS381 - YS383
1YS401
1YS451
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 1: September 28, 2016
25 of 51
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 26

GroupVariable Number
1YS456 - YS457
1YS462
1YS467
1YS501 - YS502
1YS506
1YS511 - YS513
1YS531
1YS551 - YS553
1YS561 - YS578
1YS581 - YS595
1YS601 - YS690
1YS701 - YS708
1YS721 - YS759
1YS761 - YS762
1YS771 - YS780
1YS806 - YS810
1YS816 - YS818
1YS823 - YS825
1YS851 - YS860
1YS876
1YS881 - YS883
1YS901 - YS909
1YS911 - YS927
1YS956 - YS957
1YS961 - YS965
1YS981 - YS983
1YS991 - YS998
1YT001 - YT004
1YT006
1YT026 - YT027
1YT031 - YT032
1YT036 - YT038
1YT061 - YT068
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 1: September 28, 2016
26 of 51
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 27

GroupVariable Number
1YT101 - YT111
1YT126 - YT130
1YT136 - YT138
1YT176 - YT181
1YT196 - YT197
1YT201
1YT206 - YT207
1YT211 - YT213
1YT251 - YT271
1YT301 - YT304
1YT306 - YT307
1YT311 - YT312
1YT321 - YT327
1YT391
1YT401 - YT403
1YT411 - YT415
1YT427
1YT461 - YT471
1YT491 - YT492
1YT501 - YT502
1YT551
1YT556
1YT561
1YT601 - YT606
1YT701 - YT702
1YT761 - YT778
1YT796
1YT801 - YT804
1YT811 - YT812
1YT831
1YT891 - YT894
1YT901 - YT908
1YU001 - YU045
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 1: September 28, 2016
27 of 51
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 28

GroupVariable Number
1YU201 - YU212
1YV001
1YV101 - YV106
1YV351 - YV352
1YV381
1YV521
2. Spares Affected
Examine your spares supply for the parts or components identified below. If any parts or components
are found, refer to Paragraph 3.B., Work Instructions for the recommended action.
Part Number
114A1110-( )
114A1220-( )
B. Concurrent Requirements
None.
C. Reason
The Bullnose of a 737-800 Krueger Flap departed an airplane during taxi and caused damage to the
wing structure and part of the thrust reverser. There have been six (6) other in-service reports of missing
Bullnose attachment hardware resulting in a Bullnose droop condition but no departure of the part from
the airplane. If this service bulletin is not accomplished, the Krueger Flap Bullnose could depart the
airplane during flight, which could damage empennage structure leading to inability to maintain continued
safe flight and landing.
Boeing Fleet Team Digest (FTD) 737NG FTD 57-15003 is related to this service bulletin.
Boeing Service Related Problem (SRP) 737NG-57-0283 is related to this service bulletin.
Revision 1 is sent to give a clarification that a removal of the attachment hardware is not necessary
when accomplishing the detailed inspection of the hardware. Also this revision changes illustrations to
show correct orientation of the attachment hardware and gives minor changes on terminology and
general references.
The data given in Information Notice 737-57A1327 IN 01 is included in this revision.
D. Description
Get access and do a one-time detailed inspection for discrepancies in the Bullnose attachment hardware
of Krueger Flaps no. 1, 2, 3 and 4. If any discrepancy is found, do a secondary detailed inspection for
any crack or any deformation and either replace the discrepant hardware or Krueger Flap.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 1: September 28, 2016
28 of 51
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 29

Effects of this Revision on airplanes on which Original Issue was previously done:
None.
The work in this service bulletin is done in the maintenance zone(s) given below.
Affected Maintenance Zones
ZoneModel
512, 513, 612, 613737-600, 737-700, 737-700C,
737-800, 737-900, 737-900ER
E. Compliance
The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to
this service bulletin. The Airworthiness Directive will make the compliance tasks and times given in this
service bulletin mandatory.
Accomplish the required actions, based on the applicable conditions in Table 1, in accordance with
Paragraph 3. Accomplishment Instructions.
A logic diagram showing compliance tasks and compliance times is included as an aid in APPENDIX
A.
Table 1: Krueger Flap Bullnose Attachment Hardware One-Time Inspection
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
-Within 6 months af-
ter the original is-
sue date of this
service bulletin.
Do a One-Time Detailed
Inspection for discrepan-
cies in the Bullnose at-
tachment hardware of
Krueger Flaps no. 1, 2, 3
and 4.
ALL AIRPLANES.
-Before further
flight.
Do a detailed inspection
of all Bullnose Hinge
Lugs and Clevis Assem-
blies on the affected
Krueger Flap, for any
crack or any deformation.
CONDITION 1: ANY AT-
TACHMENT HARDWARE
DISCREPANCY FOUND
ON A KRUEGER FLAP.
-Before further
flight.
Replace affected Krueger
Flap.
CONDITION 1.1: ANY
CRACK OR ANY DEFOR-
MATION FOUND ON
BULLNOSE HINGE LUGS
OR CLEVIS ASSEMBLIES.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 1: September 28, 2016
29 of 51
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 30

Table 1: Krueger Flap Bullnose Attachment Hardware One-Time Inspection
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
-Before further
flight.
Replace Discrepant
Krueger Flap Bullnose
attachment hardware.
CONDITION 1.2: NO
CRACK OR DEFORMA-
TION FOUND ON BULL-
NOSE HINGE LUGS OR
CLEVIS ASSEMBLIES.
--No further action re-
quired.
CONDITION 2: NO AT-
TACHMENT HARDWARE
DISCREPANCY FOUND
ON A KRUEGER FLAP.
F. Approval
This service bulletin was examined by the Federal Aviation Administration (FAA). The changes specified
in this service bulletin comply with the applicable regulations and are FAA approved, as well as European
Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved
airplanes listed in the service bulletin effectivity. This service bulletin and its approval were based on
the airplane in its original Boeing delivery configuration or as modified by other approved Boeing
changes.
If an airplane has a non-Boeing modification or repair that affects a component or system also affected
by this service bulletin, the operator is responsible for obtaining appropriate regulatory agency approval
before incorporating this service bulletin.
G. Manpower
The table below shows an estimate of the task hours necessary to do this inspection for each wing.
This estimate is for direct labor only, done by an experienced crew. Adjust the estimate with operator
task hour data if necessary. The estimate does not include lost time. These are some examples of lost
time:
• Time to adjust to the workplace
• Time to schedule the work
• Time to inspect the work
• Time to cure the materials
• Time to make the parts
• Time to find the tools
Table 1: One-Time Detailed Inspection and Installation of Bullnose Attachment Hardware
of Krueger Flaps No. 1, 2, 3, and 4
Elapsed HoursTask HoursNumber of PersonsTask
0.600.601Figure 1
0.600.601Figure 2
0.800.801Figure 3
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 1: September 28, 2016
30 of 51
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 31

Table 1: One-Time Detailed Inspection and Installation of Bullnose Attachment Hardware
of Krueger Flaps No. 1, 2, 3, and 4
Elapsed HoursTask HoursNumber of PersonsTask
0.800.801Figure 4
2.802.80TOTAL FOR EACH AIRPLANE
H. Weight and Balance Changes
None.
I. Electrical Load Data
Not Changed
J. References
1. Existing Data:
a. Boeing Service Related Problem (SRP) 737NG-57-0283
b. Component Maintenance Manual (CMM) 57-56-33, 57-56-44
c. Service Bulletin Index D6-19567
d. Standard Overhaul Practices Manual (SOPM) 20-50-01, 20-50-02
e. 737-600/700/800/900 Aircraft Maintenance Manual (AMM) 27-81-00, 27-81-11
f. 737NG Fleet Team Digest (FTD) 57-15003
2. Data Supplied with this Service Bulletin:
None.
3. Installation Drawings Used in the Preparation of this Service Bulletin:
TitleDrawing Number
KRUEGER FLAP INSTL - INBD WING L.E.114A1001
The table above lists applicable drawings used to prepare this service bulletin. The drawings are
not necessary to make the specified changes, and are not supplied with this service bulletin. The
drawings may not be applicable to all airplane configurations or operators.
K. Publications Affected
1. Publications:
None.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 1: September 28, 2016
31 of 51
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 32

2. Damage Tolerance Based Structural Inspections:
Boeing has evaluated the repairs and/or changes in this service bulletin for effects on Fatigue
Critical Structure (FCS) and for changes to Damage Tolerance Inspections (DTI) required in the
Maintenance Program. This service bulletin does not affect FCS, therefore DTIs are not necessary.
L. Interchangeability and Intermixability of Parts
Accomplishment of this service bulletin does not affect interchangeability or intermixability of parts.
M. Software Accomplishment Summary
Not affected.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 1: September 28, 2016
32 of 51
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 33

2.    MATERIAL INFORMATION
A. Material - Price and Availability
The operator can supply the parts and materials shown in Paragraph 2.C., Parts Necessary for Each
Airplane and Paragraph 2.D., Parts Necessary to Change Spares. As an alternative, operators can
purchase the parts from Boeing Spares. This service bulletin does not show the Boeing price and
supply data.
B. Industry Support Information
Boeing warranty remedies are available for 737 airplanes in warranty as of January 28, 2015. For
inspection labor task hour reimbursement for airplanes in warranty as of that date, send a warranty
claim to Boeing Fleet Support Contracts - Warranty. If the condition described in this service bulletin
is found during the inspection for airplanes in warranty as of that date and additional task hours are
required, send a warranty claim to Boeing Fleet Support Contracts - Warranty. Please refer to this
service bulletin number and reference the airplane variable number(s) in your purchase order. The
warranty remedies will expire eight years from the original issue date of this service bulletin.
C. Parts Necessary for Each Airplane
1. Kits/Parts
None.
2. Parts and Materials Supplied by the Operator
The following parts or materials are necessary if Attachment Hardware discrepancies are found.
Parts and materials in the manuals given in Paragraph 1.J., References, can also be necessary.
Examine operator part and material supply to make sure all necessary parts and materials are
available.
NotesNameQTYPart Number /
Specification
(a)BOLT1BACB30NR4DK14
(a)WASHER1BACW10BP4ACU
(a)WASHER1BACW10BP4APU
(a)NUT1BACN10JD104CD
(a)COTTER PIN1BACP18BC02A04P
(a) This part is per attachment joint. There are 12 attachment joints for Krueger Flap Bullnose
per airplane, six per wing.
3. Parts Modified and Reidentified
None.
4. Parts Removed and Not Replaced
None.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 1: September 28, 2016
33 of 51
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 34

D. Parts Necessary to Change Spares
None.
E. Special Tooling - Price and Availability
None.
F. Special Tooling Necessary to do this Service Bulletin
No special tools or equipment are necessary to do the change in this service bulletin. But, maintenance
and overhaul tools in the manuals given in Paragraph 1.J., References, can be necessary. Examine
operator tool supply to make sure all necessary tools are available.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 1: September 28, 2016
34 of 51
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 35

3.    ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL INFORMATION
NOTE: 1. Manual titles are referred to by acronyms. Refer to Paragraph 1.J., References, for
definition of the acronyms.
2. Obey all of the warnings and cautions given in the specified manual sections.
3. Unless shown differently, these dimensions and tolerances are used:
– Linear dimensions are in inches
– Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus
or minus 0.03 inch
– Tolerance on rivet and bolt edge margin is plus or minus 0.05 inch
– Angular tolerance is plus or minus 2 degrees
– Hole dimensions for standard solid rivets and fasteners are in Structural Repair
Manual (SRM) Chapter 51
– Torque Values:
— Values for structural fasteners are given in 737 Structural Repair Manual,
Chapter 51.
— Values for airframe maintenance tasks are included in Chapter 20 of 737
Aircraft Maintenance Manual (AMM).
— Values for engine maintenance tasks are included in Chapter 70 of 737
Aircraft Maintenance Manual (AMM).
— Non-standard torque values for maintenance tasks are included in the
applicable installation step.
4. Use the approved fastener, process and material substitutions in accordance with
SRM Chapter 51.
5. If the length of any fastener specified in this service bulletin does not meet installation
standards given in SRM Chapter 51, then a fastener of the same specification, or
an approved substitute, with a length which meets the installation standards given
in SRM Chapter 51 may be used. In addition, washers may be installed for fastener
grip length in accordance with SRM Chapter 51. Refer to SOPM 20-50-01 for alternate
full threaded fasteners (screws) needed for installation in this service bulletin.
6. A Detailed Inspection is defined as: An intensive examination of a specific item,
installation, or assembly to detect damage, failure, or irregularity. Available lighting
is normally supplemented with a direct source of good lighting at an intensity deemed
appropriate. Inspection aids such as mirrors, magnifying lenses, etc. may be
necessary. Surface cleaning and elaborate procedures may be required.
7. These work instructions refer to procedures included in other Boeing documents.
When the words "refer to" are used and the operator has an accepted alternative
procedure, the accepted alternative procedure can be used. When the words "in
accordance with" are included in the instruction, the procedure in the Boeing document
must be used.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 1: September 28, 2016
35 of 51
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 36

8. The instructions in Paragraph 3.B., Work Instructions and the figures can include
operation of tools or test equipment. Boeing Engineering Tool Drawings, the Illustrated
Tool and Equipment Manual, and the Special Tool and Ground Handling Drawing
Index contain data on versions of the tools or test equipment that you can use. It is
permitted to use replaced tools. It is not permitted to use superseded tools.
9. If it is necessary to remove more parts for access, you can remove those parts. If
you can get access without removing identified parts, it is not necessary to remove
all of the identified parts. Jacking and shoring limitations must be observed.
10. Where the work instructions include installation of a kept part, a new or serviceable
part with the same part number can be installed as an alternative to the kept part.
11. Use of colors in Figures is based on guidance from the ATA e-Business Program
(ATA) iSpec 2200.
12. The compliance times for the actions in Paragraph 3.B., WORK INSTRUCTIONS
are in Paragraph 1.E., Compliance.
13. Refer to APPENDIX A for logic diagram. Logic diagrams are provided as an aid only.
Information contained in Paragraph 1.E., Compliance is the primary source for
compliance times. Information in Paragraph 3.B., Work Instructions is the primary
source for tasks required for compliance.
14. Some steps in the Work Instructions are labeled as Required for Compliance (RC).
If this service bulletin is mandated by an Airworthiness Directive (AD), then the steps
labeled as RC, including sub-steps under an RC step and any figures identified in
an RC step, must be done to comply with the AD. An Alternative Method of
Compliance (AMOC) is required for any deviations to RC steps, including sub-steps
and identified figures. Steps not labeled as RC may be deviated from using accepted
methods in accordance with the operator's maintenance or inspection program without
obtaining approval of an AMOC. This is provided that the RC steps, including
sub-steps and identified figures, can still be done as specified, and the airplane can
be put back in an airworthy condition.
B. WORK INSTRUCTIONS
1. Extend Krueger Flaps fully to get access. Refer to 737-600/700/800/900 AMM 27-81-00 as an
accepted procedure.
2. RC - Do a one-time detailed inspection for discrepancies in the Bullnose attachment hardware on
Krueger Flaps no. 1, 2, 3 and 4 in accordance with FIGURE 1 and FIGURE 2. Discrepancies in
the Bullnose attachment hardware include any bolt, washer, castellated nut, or cotter pin
discrepancy.
NOTE: The detailed inspection for discrepancies in the Bullnose attachment hardware is
accomplished on the visible area of the attachment hardware, as is installed. It is not
necessary to disassemble the joint to do the detailed inspection.
a. CONDITION 1: ANY ATTACHMENT HARDWARE DISCREPANCY FOUND ON A KRUEGER
FLAP.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 1: September 28, 2016
36 of 51
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 37

(1) Do a detailed inspection of all Bullnose Hinge Lugs and Clevis Assemblies on the affected
Krueger Flap, for any crack or any deformation.
(a) CONDITION 1.1: ANY CRACK OR ANY DEFORMATION FOUND ON BULLNOSE
HINGE LUGS OR CLEVIS ASSEMBLIES.
1) Replace affected Krueger Flap. Refer to 737-600/700/800/900 AMM 27-81-11
"LEADING EDGE FLAPS - REMOVAL/INSTALLATION"
(b) CONDITION 1.2: NO CRACK OR DEFORMATION FOUND ON BULLNOSE HINGE
LUGS OR CLEVIS ASSEMBLIES.
1) Replace Discrepant Krueger Flap Bullnose Attachment Hardware in accordance
with FIGURE 3 or FIGURE 4.
b. CONDITION 2: NO ATTACHMENT HARDWARE DISCREPANCY FOUND ON A KRUEGER
FLAP.
(1) No Further Action Required.
3. Put the airplane back to a serviceable condition.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 1: September 28, 2016
37 of 51
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 38 (OCR)

BOEING SERVICE BULLETIN 737-57A1327
ALERT  ALERT
ESIA  LE STA
218.88  206.32
LE STA
190.85  LE STA  LE STA
180.52  166.32
LE STA
158.82
INBD
NO. 1 KRUEGER FLAP
2483910
FIGURE 1: LEFT WING - KRUEGER FLAP 1 AND 2 BULLNOSE ATTACHMENT HARDWARE ONE-TIME
INSPECTION
(SHEET 1 OF 3)
Original Issue: May 20, 2016
Revision 1 September 28, 2016  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  737-57A1327
Work - See page 1 for details.  38 of 51

### Page 39 (OCR)

BOEING SERVICE BULLETIN 737-57A1327
ALERT  ALERT
LE STA
150.82
LE STA
104.52
INBD
NO. 2 KRUEGER FLAP
BULLNOSE  CLEVIS  BULLNOSE  1 COTTER PIN LEGS
HINGE LUG  ASSEMBLY HINGE LUG
• COTTER PIN HEAD
CLEVIS  INBD
A-A  2483919
FIGURE 1: LEFT WING - KRUEGER FLAP 1 AND 2 BULLNOSE ATTACHMENT HARDWARE ONE-TIME
INSPECTION
(SHEET 2 OF 3)
Original Issue: May 20, 2016
Revision 1 September 28, 2016  Export Controlled ECCN: 9E991 - BOEING  737-57A1327
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  39 of 51

### Page 40

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for each attachment location shown in this figure.
More DataQtyIdentificationNameTaskStep
Do a Detailed Inspec-
tion for discrepan-
cies.(d) (e)
1BACP18BC02A04PCOTTER PINInspect1
Do a Detailed Inspec-
tion for discrepan-
cies.(a) (e)
1BACN10JD104CDCASTELLATED NUTInspect2
Do a Detailed Inspec-
tion for discrepan-
cies.(b) (e)
1BACW10BP4APUWASHERInspect3
Do a Detailed Inspec-
tion for discrepan-
cies.(b) (e)
1BACW10BP4ACUWASHERInspect4
Do a Detailed Inspec-
tion for discrepan-
cies.(c) (e)
1BACB30NR4DK14BOLTInspect5
(a) Castellated nut discrepancies include missing, loose, worn, cracked, or damaged castellated nuts. Damage
is defined as, but not limited to, any dent(s), nick(s), or gouge(s).
(b) Washer discrepancies include missing, loose, worn, or damaged washers. Damage is defined as, but not
limited to, any dent(s), nick(s), or gouge(s).
(c) Bolt discrepancies include bolts that do not meet end protrusion for minimum threads, missing, cracked,
loose, or damaged bolts. Damage is defined as, but not limited to, any dent(s), nick(s), or gouge(s).
(d) Cotter pin discrepancies include missing cotter pins and cotter pins with head protrusion and cotter pin
leg bend orientation that do not match SOPM 20-50-02. Refer to SOPM 20-50-02 as an accepted procedure
for installation of cotter pins.
(e) The detailed inspection for discrepancies in the Bullnose attachment hardware is accomplished on the
visible area of the attachment hardware, as is installed. It is not necessary to disassemble the joint to do
the detailed inspection.
FIGURE 1: LEFT WING - KRUEGER FLAP 1 AND 2 BULLNOSE ATTACHMENT HARDWARE ONE-TIME
INSPECTION
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 1 September 28, 2016
40 of 51
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 41 (OCR)

BOEING SERVICE BULLETIN 737-57A1327
ALERT  ALERT
LE STA  LE STA
206.32  218.88
LE STA
LE STA  LE STA  190.85
LE STA  166.32  180.52
158.82
INBD
NO. 4 KRUEGER FLAP
2483921
FIGURE 2: RIGHT WING - KRUEGER FLAP 3 AND 4 BULLNOSE ATTACHMENT HARDWARE ONE-TIME
INSPECTION
(SHEET 1 OF 3)
Original Issue: May 20, 2016
Revision 1 September 28, 2016  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  737-57A1327
Work - See page 1 for details.  41 of 51

### Page 42 (OCR)

BOEING SERVICE BULLETIN 737-57A1327
ALERT  ALERT
LE STA
150.82
LE STA
104.52
INBD
NO. 3 KRUEGER FLAP
BULLNOSE  CLEVIS  BULLNOSE
COTTER PIN LEGS (  HINGE LUG  ASSEMBLY HINGE LUG
COTTER PIN HEAD
CLEVIS  INBD
A-A  2483928
FIGURE 2: RIGHT WING - KRUEGER FLAP 3 AND 4 BULLNOSE ATTACHMENT HARDWARE ONE-TIME
INSPECTION
(SHEET 2 OF 3)
Original Issue: May 20, 2016
Revision 1 September 28, 2016  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  737-57A1327
Work - See page 1 for details.  42 of 51

### Page 43

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for each attachment location shown in this figure.
More DataQtyIdentificationNameTaskStep
Do a Detailed Inspec-
tion for discrepan-
cies.(d) (e)
1BACP18BC02A04PCOTTER PINInspect1
Do a Detailed Inspec-
tion for discrepan-
cies.(a) (e)
1BACN10JD104CDCASTELLATED NUTInspect2
Do a Detailed Inspec-
tion for discrepan-
cies.(b) (e)
1BACW10BP4APUWASHERInspect3
Do a Detailed Inspec-
tion for discrepan-
cies.(b) (e)
1BACW10BP4ACUWASHERInspect4
Do a Detailed Inspec-
tion for discrepan-
cies.(c) (e)
1BACB30NR4DK14BOLTInspect5
(a) Castellated nut discrepancies include missing, loose, worn, cracked, or damaged castellated nuts. Damage
is defined as, but not limited to, any dent(s), nick(s), or gouge(s).
(b) Washer discrepancies include missing, loose, worn, or damaged washers. Damage is defined as, but not
limited to, any dent(s), nick(s), or gouge(s).
(c) Bolt discrepancies include bolts that do not meet end protrusion for minimum threads, missing, cracked,
loose, or damaged bolts. Damage is defined as, but not limited to, any dent(s), nick(s), or gouge(s).
(d) Cotter pin discrepancies include missing cotter pins and cotter pins with head protrusion and cotter pin
leg bend orientation that do not matchSOPM 20-50-02. Refer to SOPM 20-50-02 as an accepted procedure
for installation of cotter pins.
(e) The detailed inspection for discrepancies in the Bullnose attachment hardware is accomplished on the
visible area of the attachment hardware, as is installed. It is not necessary to disassemble the joint to do
the detailed inspection.
FIGURE 2: RIGHT WING - KRUEGER FLAP 3 AND 4 BULLNOSE ATTACHMENT HARDWARE ONE-TIME
INSPECTION
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 1 September 28, 2016
43 of 51
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 44 (OCR)

BOEING SERVICE BULLETIN 737-57A1327
ALERT  ALERT
LE STA  LE STA
218.88  206.32
LE STA
190.85  LE STA  LE STA
180.52  166.32  LE STA
158.82
INBD
NO. 1 KRUEGER FLAP
2487991
FIGURE 3: LEFT WING - KRUEGER FLAP 1 AND 2 BULLNOSE ATTACHMENT HARDWARE INSTALLATION
(SHEET 1 OF 3)
Original Issue: May 20, 2016
Revision 1 September 28, 2016  Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright © Unpublished  737-57A1327
Work - See page 1 for details.  44 of 51

### Page 45 (OCR)

BOEING SERVICE BULLETIN 737-57A1327
ALERT  ALERT
LE STA
150.82
LE STA
104.52
INBD
NO. 2 KRUEGER FLAP
BULLNOSE  CLEVIS  BULLNOSE  (5) COTTER PIN LEGS
HINGE LUG  ASSEMBLY HINGE LUG
) COTTER PIN HEAD
CLEVIS  INBD
A-A  2528090
FIGURE 3: LEFT WING - KRUEGER FLAP 1 AND 2 BULLNOSE ATTACHMENT HARDWARE INSTALLATION
(SHEET 2 OF 3)
Original Issue: May 20, 2016
Revision 1 September 28, 2016  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  737-57A1327
Work - See page 1 for details.  45 of 51

### Page 46

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for each attachment location shown in this figure.
More DataQtyIdentificationNameTaskStep
(a)1BACW10BP4ACUWASHERInstall (New)1
(a)1BACB30NR4DK14BOLTInstall (New)2
(a)1BACW10BP4APUWASHERInstall (New)3
(a)1BACN10JD104CDCASTELLATED NUTInstall (New)4
Refer to SOPM 20-
50-02 as an accept-
ed procedure.
1BACP18BC02A04PCOTTER PINInstall (New)5
(a) Install new part if part was discrepant, or install kept part if part is not discrepant. Refer to CMM 57-56-33
and SOPM 20-50-02 as an accepted procedure.
FIGURE 3: LEFT WING - KRUEGER FLAP 1 AND 2 BULLNOSE ATTACHMENT HARDWARE INSTALLATION
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 1 September 28, 2016
46 of 51
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 47 (OCR)

BOEING SERVICE BULLETIN 737-57A1327
ALERT  ALERT
LE STA  LE STA
206.32  218.88
LE STA
LE STA  LE STA  190.85
LE STA  166.32  180.52
158.82
INBD
NO. 4 KRUEGER FLAP
2487992
FIGURE 4: RIGHT WING - KRUEGER FLAP 3 AND 4 BULLNOSE ATTACHMENT HARDWARE
INSTALLATION
(SHEET 1 OF 3)
Original Issue: May 20, 2016
Revision 1 September 28, 2016  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  737-57A1327
Work - See page 1 for details.  47 of 51

### Page 48 (OCR)

BOEING SERVICE BULLETIN 737-57A1327
ALERT  ALERT
LE STA
150.82
LE STA
104.52
INBD
NO. 3 KRUEGER FLAP
BULLNOSE  CLEVIS  BULLNOSE
COTTER PIN LEGS ( 5  HINGE LUG  ASSEMBLY HINGE LUG
COTTER PIN HEAD
NBI  CLEVIS
A-A  2528098
FIGURE 4: RIGHT WING - KRUEGER FLAP 3 AND 4 BULLNOSE ATTACHMENT HARDWARE
INSTALLATION
(SHEET 2 OF 3)
Original Issue: May 20, 2016
Revision 1 September 28, 2016  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  737-57A1327
Work - See page 1 for details.  48 of 51

### Page 49

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for each attachment location shown in this figure.
More DataQtyIdentificationNameTaskStep
(a)1BACW10BP4ACUWASHERInstall (New)1
(a)1BACB30NR4DK14BOLTInstall (New)2
(a)1BACW10BP4APUWASHERInstall (New)3
(a)1BACN10JD104CDCASTELLATED NUTInstall (New)4
Refer to SOPM 20-
50-02 as an accept-
ed procedure.
1BACP18BC02A04PCOTTER PINInstall (New)5
(a) Install new part if part was discrepant, or install kept part if part is not discrepant. Refer to CMM 57-56-44
and SOPM 20-50-02 as an accepted procedure.
FIGURE 4: RIGHT WING - KRUEGER FLAP 3 AND 4 BULLNOSE ATTACHMENT HARDWARE
INSTALLATION
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 1 September 28, 2016
49 of 51
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 50

Logic diagrams are provided as an aid only. Information contained in Paragraph 1.E., Compliance is the primary
source for compliance times. Information contained in Paragraph 3.B., Work Instructions is the primary source
for tasks required for compliance.
APPENDIX A:  LOGIC DIAGRAM FOR PARAGRAPH 1.E. COMPLIANCE: TABLE 1: KRUEGER FLAP
BULLNOSE ATTACHMENT HARDWARE ONE-TIME INSPECTION.
(SHEET 1 OF 2)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 20, 2016
737-57A1327Revision 1 September 28, 2016
50 of 51
BOEING SERVICE BULLETIN 737-57A1327
ALERTALERT

### Page 51 (OCR)

BOEING SERVICE BULLETIN 737-57A1327
ALERT  ALERT
WITHIN 6 MONTHS AFTER THE ORIGINAL ISSUE
DATE OF THIS SERVICE BULLETIN
DO A ONE-TIME DETAILED
INSPECTION FOR DISCREPANCIES
IN THE BULLNOSE ATTACHMENT
HARDWARE OF KRUEGER FLAPS
NO. 1, 2, 3 AND 4
CONDITION 1: ANY ATTACHMENT
HARDWARE DISCREPANCY
FOUND ON A KRUEGER FLAP
CONDITION 2: NO ATTACHMENT
HARDWARE DISCREPANCY
FOUND ON A KRUEGER FLAP
BEFORE FURTHER  NO FURTHER ACTION
FLIGHT  REQUIRED
DO A DETAILED INSPECTION OF ALL
BULLNOSE HINGE LUGS AND CLEVIS
ASSEMBLIES ON THE AFFECTED KRUEGER
FLAP, FOR ANY CRACK OR ANY DEFORMATION
CONDITION 1.1: ANY CRACK OR  CONDITION 1.2: NO CRACK OR
ANY DEFORMATION FOUND ON  DEFORMATION FOUND ON
BULLNOSE HINGE LUGS OR  BULLNOSE HINGE LUGS OR
CLEVIS ASSEMBLIES  CLEVIS ASSEMBLIES
BEFORE FURTHER  BEFORE FURTHER
FLIGHT  FLIGHT
REPLACE DISCREPANT
REPLACE AFFECTED  KRUEGER FLAP BULLNOSE
KRUEGER FLAP  ATTACHMENT HARDWARE
2488002
APPENDIX A: LOGIC DIAGRAM FOR PARAGRAPH 1.E. COMPLIANCE: TABLE 1: KRUEGER FLAP
BULLNOSE ATTACHMENT HARDWARE ONE-TIME INSPECTION.
(SHEET 2 OF 2)
Original Issue: May 20, 2016
Revision 1 September 28, 2016  Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright © Unpublished  737-57A1327
Work - See page 1 for details.  51 of 51

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
