# Boeing Alert Requirements Bulletin 737-57A1338 RB: No revision named

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2018-0112; AD 2018-18-13 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Alert Requirements Bulletin 737-57A1338 RB](https://openairdocs.org/service-documents/boeing/737-57a1338-rb.md)
- Title as filed: SB737-57A1338RB
- Pages: 161
- PDF: https://openairdocs.org/files/sha256/d1/d6/d1d6bf6041e4370066b32755657bcb52df6741d3f47f8f7f09b78add8b8f77d7
- Page: https://openairdocs.org/service-documents/boeing/737-57a1338-rb/file/d1d6bf6041e4

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Commercial 
Airplanes
737
Requirements Bulletin
ALERT
Number: 737-57A1338 RB
Original Issue: September 25, 2017
ATA System: 5752 2751
SUBJECT: WINGS - Trailing Edge Flaps - Outboard Flap Tracks at Wing Buttock Line 254 and
355 Inspection
Export of this technology is controlled under the United States Export Administration Regulations (EAR) (15
CFR 300-774). An export license may be required before it is used for development, production or use by foreign
persons from specific countries. The controller of this data has the individual responsibility to abide by all export
laws.
9E991ECCN:
BOEING PROPRIETARY, CONFIDENTIAL AND/OR TRADE SECRET
Copyright © 2017 Boeing.
Unpublished Work. All Rights Reserved.
Treatment of this document and its content is governed by contract with Boeing. Rights to use this document
are licensed on a per aircraft basis and such rights may not be transferable. For more information, contact The
Boeing Company.
Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner,
BBJ, DC-8, DC-9, DC-10, KC-10, KC-46, KDC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8, Poseidon and
Boeing liveries are all trademarks owned by The Boeing Company; and no trademark license is granted in
connection with this document unless provided in writing by Boeing.
Original Issue: September 25, 2017
737-57A1338 RB
1 of 161
3.0

### Page 2

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 25, 2017
737-57A1338 RB
2 of 161
REQUIREMENTS BULLETIN 737-57A1338
ALERTALERT
BLANK PAGE

### Page 3

Table of Contents
1 . E F F E C T I V I T Y  ................................................ 5
A. Airplanes ................................................ 5
B . S p a r e s  A f f e c t e d  ............................................ 5
2. CONCURRENT REQUIREMENTS ..................................... 7
3 . C O M P L I A N C E  ................................................ 7
4. APPROVAL ................................................ 3 4
5. ACCOMPLISHMENT INSTRUCTIONS .................................. 3 5
A. General Information ......................................... 3 5
B. Work Instructions ........................................... 3 7
FIGURE 1: LEFT WING - WBL 355 - FLAP TRACK POSITION 1 - DETAILED INSPECTION [Group 2-3]
.................................................. 6 8
FIGURE 2: RIGHT WING - WBL 355 - FLAP TRACK POSITION 8 - DETAILED INSPECTION [Group 2-3]
.................................................. 7 0
FIGURE 3: LEFT WING - WBL 254 - FLAP TRACK POSITION 2 - DETAILED INSPECTION [Group 2-3]
.................................................. 7 2
FIGURE 4: RIGHT WING - WBL 254 - FLAP TRACK POSITION 7 - DETAILED INSPECTION [Group 2-3]
.................................................. 7 4
FIGURE 5: LEFT WING - WBL 355 - FLAP TRACK POSITION 1 - SURFACE HFEC INSPECTION [Group
2 ]  ................................................ 7 6
FIGURE 6: RIGHT WING - WBL 355 - FLAP TRACK POSITION 8 - SURFACE HFEC INSPECTION [Group
2 ]  ................................................ 8 0
FIGURE 7: LEFT WING - WBL 355 - FLAP TRACK POSITION 1 - SURFACE HFEC INSPECTION [Group
3, Configuration 1] ....................................... 8 4
FIGURE 8: RIGHT WING - WBL 355 - FLAP TRACK POSITION 8 - SURFACE HFEC INSPECTION [Group
3, Configuration 1] ....................................... 8 8
FIGURE 11: LEFT WING - WBL 355 - FLAP TRACK POSITION 1 - SURFACE HFEC INSPECTION AND
OPEN HOLE HFEC INSPECTION [Group 3, Configuration 2] ................ 9 2
FIGURE 12: RIGHT WING - WBL 355 - FLAP TRACK POSITION 8 - SURFACE HFEC INSPECTION AND
OPEN HOLE HFEC INSPECTION [Group 3, Configuration 2] ................ 9 6
FIGURE 15: LEFT WING - WBL 254 - FLAP TRACK POSITION 2 - SURFACE HFEC INSPECTION [Group
2 ]  ................................................ 1 0 0
FIGURE 16: RIGHT WING - WBL 254 - FLAP TRACK POSITION 7 - SURFACE HFEC INSPECTION [Group
2 ]  ................................................ 1 0 3
FIGURE 17: LEFT WING - WBL 254 - FLAP TRACK POSITION 2 - SURFACE HFEC INSPECTION [Group
3, Configuration 1] ....................................... 1 0 6
FIGURE 18: RIGHT WING - WBL 254 - FLAP TRACK POSITION 7 - SURFACE HFEC INSPECTION [Group
3, Configuration 1] ....................................... 1 0 9
FIGURE 21: LEFT WING - WBL 254 - FLAP TRACK POSITION 2 - SURFACE HFEC INSPECTION AND
OPEN HOLE HFEC INSPECTION [Group 3, Configuration 2] ............... 1 1 2
FIGURE 22: RIGHT WING - WBL 254 - FLAP TRACK POSITION 7 - SURFACE HFEC INSPECTION AND
OPEN HOLE HFEC INSPECTION [Group 3, Configuration 2] ............... 1 1 5
FIGURE 25: LEFT WING - WBL 254 - FLAP TRACK POSITION 2 - SURFACE HFEC INSPECTION [Group
2 - 3 ]  ............................................... 1 1 8
FIGURE 26: RIGHT WING - WBL 254 - FLAP TRACK POSITION 7 - SURFACE HFEC INSPECTION [Group
2 - 3 ]  ............................................... 1 2 2
FIGURE 27: LEFT WING - WBL 355 - FLAP TRACK POSITION 1 - SURFACE HFEC INSPECTION AND
ULTRASONIC INSPECTION [Group 2-3] .......................... 1 2 6
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 25, 2017
737-57A1338 RB
3 of 161
REQUIREMENTS BULLETIN 737-57A1338
ALERTALERT

### Page 4

FIGURE 28: RIGHT WING - WBL 355 - FLAP TRACK POSITION 8 - SURFACE HFEC INSPECTION AND
ULTRASONIC INSPECTION [Group 2-3] .......................... 1 2 8
FIGURE 29: LEFT WING - WBL 254 - FLAP TRACK POSITION 2 - SURFACE HFEC INSPECTION AND
ULTRASONIC INSPECTION [Group 2-3] .......................... 1 3 0
FIGURE 30: RIGHT WING - WBL 254 - FLAP TRACK POSITION 7 - SURFACE HFEC INSPECTION AND
ULTRASONIC INSPECTION [Group 2-3] .......................... 1 3 2
FIGURE 33: LEFT WING - WBL 355 - FLAP TRACK POSITION 1 - ANTI-FRET STRIP, TAPERED SHIM
AND FLAP TRACK - DETAILED INSPECTION [Group 2-3] ................ 1 3 4
FIGURE 34: RIGHT WING - WBL 355 - FLAP TRACK POSITION 8 - ANTI-FRET STRIP, TAPERED SHIM
AND FLAP TRACK - DETAILED INSPECTION [Group 2-3] ................ 1 3 7
FIGURE 39: LEFT WING - WBL 254 - FLAP TRACK POSITION 2 - ANTI-FRET STRIP, TAPERED SHIM
AND FLAP TRACK - DETAILED INSPECTION [Group 2-3] ................ 1 4 0
FIGURE 40: RIGHT WING - WBL 254 - FLAP TRACK POSITION 7 - ANTI-FRET STRIP, TAPERED SHIM
AND FLAP TRACK - DETAILED INSPECTION [Group 2-3] ................ 1 4 3
FIGURE 45: LEFT WING - WBL 355 - FLAP TRACK POSITION 1 - ANTI-FRET STRIP, TAPERED SHIM,
FLAP TRACK AND BUSHING - DETAILED INSPECTION [Group 2-3] .......... 1 4 6
FIGURE 46: RIGHT WING - WBL 355 - FLAP TRACK POSITION 8 - ANTI-FRET STRIP, TAPERED SHIM,
FLAP TRACK AND BUSHING - DETAILED INSPECTION [Group 2-3] .......... 1 4 8
FIGURE 47: LEFT WING - WBL 355 - FLAP TRACK POSITION 1 - SURFACE HFEC INSPECTION AND
OPEN HOLE HFEC INSPECTION [Group 2-3] ....................... 1 5 0
FIGURE 48: RIGHT WING - WBL 355 - FLAP TRACK POSITION 8 - SURFACE HFEC INSPECTION AND
OPEN HOLE HFEC INSPECTION [Group 2-3] ....................... 1 5 2
FIGURE 51: LEFT WING - WBL 254 - FLAP TRACK POSITION 2 - ANTI-FRET STRIP, TAPERED SHIM,
FLAP TRACK AND BUSHING - DETAILED INSPECTION [Group 2-3] .......... 1 5 4
FIGURE 52: RIGHT WING - WBL 254 - FLAP TRACK POSITION 7 - ANTI-FRET STRIP, TAPERED SHIM,
FLAP TRACK AND BUSHING - DETAILED INSPECTION [Group 2-3] .......... 1 5 6
FIGURE 53: LEFT WING - WBL 254 - FLAP TRACK POSITION 2 - SURFACE HFEC INSPECTION AND
OPEN HOLE HFEC INSPECTION [Group 2-3] ....................... 1 5 8
FIGURE 54: RIGHT WING - WBL 254 - FLAP TRACK POSITION 7 - SURFACE HFEC INSPECTION AND
OPEN HOLE HFEC INSPECTION [Group 2-3] ....................... 1 6 0
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 25, 2017
737-57A1338 RB
4 of 161
REQUIREMENTS BULLETIN 737-57A1338
ALERTALERT

### Page 5

Commercial 
Airplanes
737
Requirements Bulletin
ALERT
Number: 737-57A1338 RB
Original Issue: September 25, 2017
ATA System: 5752 2751
SUBJECT: WINGS - Trailing Edge Flaps - Outboard Flap Tracks at Wing Buttock Line 254 and
355 Inspection
THIS DOCUMENT IS SENT TO THE OPERATORS OF RECORD OF THE AIRPLANES SHOWN IN
PARAGRAPH 1.A., EFFECTIVITY. IF AN AIRPLANE HAS BEEN LEASED OR SOLD, SEND THIS DOCUMENT
TO THE NEW OPERATOR. IF APPLICABLE SPARES HAVE BEEN SOLD, SEND THIS DOCUMENT TO THE
NEW OWNER. THIS IS AN ENHANCED REQUIRED FOR COMPLIANCE DOCUMENT. THE BOEING
PROCESSES USED TO CREATE THE SERVICE BULLETIN (SB) AND THE REQUIREMENTS BULLETIN
(RB) ENSURE THAT THE INFORMATION BETWEEN "RC START" AND "RC END" IN THE SB ARE IDENTICAL
TO THE INFORMATION IN THE SAME SECTIONS (COMPLIANCE, WORK INSTRUCTIONS…) OF THE RB
WHICH THE SB REFERS TO AS THE RELATED DOCUMENT.
1. EFFECTIVITY
A. Airplanes
This bulletin is applicable to all 737-100/200/200C/300/400/500 Airplanes, line numbers 1 thru 3132.
DESCRIPTIONCONFIGURATIONGROUP
737-100/200/200C airplanes, line numbers 1 thru 291.-1
737-200/200C airplanes, line numbers 292 thru 1585 with outboard
flap track assemblies 65-46428-( ), or 65-67158-( ).
-2
737-300/400/500 airplanes, line numbers 1001 thru 3132.-3
Airplanes with outboard flap track assemblies 65-46428-( ), or
65C34812-( ).
1
Airplanes with outboard flap track assemblies 65C35386-( ), or
65C35387-( ), or 65C35615-( ), or 65C35616-( ).
2
B. Spares Affected
Examine your spares supply for the parts or components identified below. If any parts or components
are found, refer to the Work Instructions for the recommended action.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 25, 2017
737-57A1338 RB
5 of 161

### Page 6

Flap Track PositionPart Number
1 / 865-46428-1
2 / 765-46428-11
1 / 865-46428-14
2 / 765-46428-15
1 / 865-46428-16
2 / 765-46428-17
1 / 865-46428-18
2 / 765-46428-19
2 / 765-46428-2
1 / 865-46428-20
2 / 765-46428-21
1 / 865-46428-22
2 / 765-46428-23
1 / 865-46428-24
2 / 765-46428-25
1 / 865-46428-26
2 / 765-46428-27
2 / 765-46428-3
1 / 865-46428-30
2 / 765-46428-31
1 / 865-46428-32
2 / 765-46428-33
1 / 865-46428-34
2 / 765-46428-35
2 / 765-46428-36
1 / 865-46428-4
2 / 765-46428-5
1 / 865-46428-6
2 / 765-46428-7
1 / 865-46428-8
2 / 765-46428-9
1 / 865-67158-1
2 / 765-67158-2
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 25, 2017
737-57A1338 RB
6 of 161
REQUIREMENTS BULLETIN 737-57A1338
ALERTALERT

### Page 7

Flap Track PositionPart Number
2 / 765-67158-3
1 / 865-67158-5
2 / 765-67158-6
1 / 865C34812-2
2 / 765C34812-3
2 / 765C34812-4
1 / 865C34812-5
2 / 765C34812-6
1 / 865C34812-7
2 / 765C34812-8
1 / 865C35386-4
2 / 765C35387-4
1 / 865C35615-2
2 / 765C35616-5
2. CONCURRENT REQUIREMENTS
None.
3. COMPLIANCE
Federal Aviation Administration (FAA) Airworthiness Directive AD 2013-09-02 is related to Requirements
Bulletin 737-57A1338 RB. The effective date of AD 2013-09-02 is June 13, 2013.
The Federal Aviation Administration (FAA) will possibly release an additional Airworthiness Directive related
to Requirements Bulletin 737-57A1338 RB. The Airworthiness Directive will make the compliance tasks
and times given in Requirements Bulletin 737-57A1338 RB mandatory.
Accomplish the required actions, based on the applicable conditions in Tables 1 through 4, in accordance
with the Accomplishment Instructions.
When more than one OPTION is given for a CONDITION, do only one of the OPTION numbers. When
more than one ACTION is given for a CONDITION number or an OPTION number, do all of the ACTION
numbers for that CONDITION number or OPTION number.
Group 1:
Boeing endorses the FAA rules related to Limit of Validity (LOV) and recommends immediate and permanent
removal from service of any airplanes upon reaching the LOV, whether or not it is operated under FAA
jurisdiction. As such, Boeing no longer provides maintenance instructions for airplanes that have accumulated
flight cycles beyond the LOV. Airplanes in Group 1 (line numbers 1-291) have accumulated flight cycles
beyond the LOV of the maintenance program. 14 CFR 121.1115 and 129.115 prohibit operation of an
airplane beyond its LOV.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 25, 2017
737-57A1338 RB
7 of 161
REQUIREMENTS BULLETIN 737-57A1338
ALERTALERT

### Page 8

Group 2; Group 3, Configuration 1:
The actions required for each INSPECTION in Table 1 are identified as follows:
Group 2; Group 3, Configuration 1:
ActionTitle
ACTION 1: Inspect the flap track assembly for part number. As an alternative to the
inspection, a review of the maintenance records can be used if the part number of the
flap track assembly can be positively determined.
INSPECTION 1
ACTION 2: Do a detailed inspection of the flap track flanges and webs for any crack,
any nick, any corrosion pit, any galling, any piece broken off, and any stop-drill repair.
ACTION 3: Do a surface High Frequency Eddy Current (HFEC) inspection of the flap
track flanges and webs for any crack.
ACTION 4: Do a surface HFEC inspection and an ultrasonic inspection of the upper
flap track flange for any crack.
ACTION 5: Do a detailed inspection of the anti-fret strip and the tapered shim for any
damage and any corrosion.
ACTION 6: Do a detailed inspection of the flap track at the rear spar attachment for
any crack, any corrosion and any loose fastener.
ACTION 1: Do a detailed inspection of the anti-fret strip for presence or absence of
the anti-fret strip and for any damage and for material.
INSPECTION 2
ACTION 2: Do a detailed inspection of the tapered shim for presence or absence, any
damage, any corrosion, and for material, and measure the width of the tapered shim
normal to its aft edge.
ACTION 3: Do a detailed inspection of the flap track in the area of the rear spar attach-
ment mating surface for any corrosion.
ACTION 4: Do a detailed inspection of the outer circumferential surface of the bushing
for any corrosion.
ACTION 5: Do a surface HFEC inspection and an open hole HFEC inspection of the
flap track for any crack.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 25, 2017
737-57A1338 RB
8 of 161
REQUIREMENTS BULLETIN 737-57A1338
ALERTALERT

### Page 9

Group 2; Group 3, Configuration 1:
Table 1: Detailed Inspections and NDT Inspections of the Outboard Flap Tracks at Positions 1 and 8
Repeat Inter-
val (Not to Ex-
ceed)
Compliance Time (Whichever Occurs Later)ActionCondition
-Within 6
months after
the original is-
sue date of Re-
quirements
Bulletin 737-
57A1338 RB.
Within 5,000 flap track flight cy-
cles or 2 years, whichever oc-
curs first, after the most recent
overhaul of the affected flap
track.
ACTION 1: Do IN-
SPECTION 1 on
each affected flap
track.
Airplanes with flap
tracks that have known
maintenance records
and on which an over-
haul was done
-Within 6
months after
the original is-
sue date of Re-
quirements
Bulletin 737-
57A1338 RB.
Whichever Occurs FirstACTION 2: Do an
overhaul of each
affected flap track. Within 10,000flap track flight
cycles or 4
years,
whichever oc-
curs first, after
the first inspec-
tion of the af-
fected flap
track in accor-
dance with Re-
quirements
Bulletin 737-
57A1338 RB.
Within 20,000
flap track flight
cycles or 8
years,
whichever oc-
curs first, after
the most re-
cent overhaul
of the affected
flap track.
-Within 6
months after
the original is-
sue date of Re-
quirements
Bulletin 737-
57A1338 RB.
Within 10,000 flap track flight
cycles or 4 years, whichever
occurs first, since the affected
flap track was new.
ACTION 1: Do IN-
SPECTION 1 on
each affected flap
track.
Airplanes with flap
tracks that have known
maintenance records
and on which no over-
haul was done
-Within 6
months after
the original is-
sue date of Re-
quirements
Bulletin 737-
57A1338 RB.
Within 20,000 flap track flight
cycles or 8 years, whichever
occurs first, since the affected
flap track was new.
ACTION 2: Do an
overhaul of each
affected flap track.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 25, 2017
737-57A1338 RB
9 of 161
REQUIREMENTS BULLETIN 737-57A1338
ALERTALERT

### Page 10

Group 2; Group 3, Configuration 1:
Table 1: Detailed Inspections and NDT Inspections of the Outboard Flap Tracks at Positions 1 and 8
Repeat Inter-
val (Not to Ex-
ceed)
Compliance Time (Whichever Occurs Later)ActionCondition
-Within 6 months after the original issue date of
Requirements Bulletin 737-57A1338 RB.
ACTION 1: Do IN-
SPECTION 1 on
each affected flap
track.
Airplanes with flap
tracks that have un-
known maintenance
records
-Within 6 months after the original issue date of
Requirements Bulletin 737-57A1338 RB.
ACTION 2: Do an
overhaul of each
affected flap track.
-Before further flight.Remove the flap
track and install a
new or serviceable
flap track. (b)
CONDITION 101: FLAP
TRACK ASSEMBLY
PART NUMBER IS 65-
46428-30 OR 65-
46428-32 (a)
-Before further flight.Remove the flap
track and install a
new or serviceable
flap track. (b)
CONDITION 102: ANY
CRACK, ANY NICK,
ANY CORROSION PIT,
ANY GALLING, ANY
PIECE BROKEN OFF
OR ANY STOP-DRILL
REPAIR FOUND during
INSPECTION 1 (a)
10,000 flap
track flight cy-
cles or 4 years,
whichever oc-
curs first.
-Repeat INSPEC-
TION 1.
CONDITION 103: NO
CRACK, NO NICK, NO
CORROSION PIT, NO
GALLING, NO PIECE
BROKEN OFF AND
NO STOP-DRILL RE-
PAIR FOUND during
INSPECTION 1 (a)
-Before further flight.ACTION 1: Do IN-
SPECTION 2 and
all applicable relat-
ed corrective ac-
tions.
CONDITION 104: ANY
DAMAGE OR ANY
CORROSION FOUND
ON THE ANTI-FRET
STRIP OR ON THE
TAPERED SHIM; OR
ANY CORROSION OR
ANY LOOSE FASTEN-
ER FOUND ON THE
FLAP TRACK AT THE
REAR SPAR ATTACH-
MENT during INSPEC-
TION 1 (a)
-Before further flight.ACTION 2: Install
the repaired flap
track, or a new or
serviceable flap
track. (b)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 25, 2017
737-57A1338 RB
10 of 161
REQUIREMENTS BULLETIN 737-57A1338
ALERTALERT

### Page 11

Group 2; Group 3, Configuration 1:
Table 1: Detailed Inspections and NDT Inspections of the Outboard Flap Tracks at Positions 1 and 8
Repeat Inter-
val (Not to Ex-
ceed)
Compliance Time (Whichever Occurs Later)ActionCondition
10,000 flap
track flight cy-
cles or 4 years,
whichever oc-
curs first.
-Repeat INSPEC-
TION 1.
CONDITION 105: NO
DAMAGE AND NO
CORROSION FOUND
ON THE ANTI-FRET
STRIP AND ON THE
TAPERED SHIM; AND
NO CORROSION AND
NO LOOSE FASTEN-
ER FOUND ON THE
FLAP TRACK AT THE
REAR SPAR ATTACH-
MENT during INSPEC-
TION 1 (a)
-Before further flight.ACTION 1: Re-
move the anti-fret
strip and install a
new anti-fret strip.
CONDITION 106: AN-
TI-FRET STRIP IS
MISSING OR ANTI-
FRET STRIP IS MADE
FROM PHENOLIC MA-
TERIAL OR ANY DAM-
AGE FOUND ON THE
ANTI-FRET STRIP
during INSPECTION 2
(a)
10,000 flap
track flight cy-
cles or 4 years,
whichever oc-
curs first.
-ACTION 2: Repeat
INSPECTION 1.
10,000 flap
track flight cy-
cles or 4 years,
whichever oc-
curs first.
-Repeat INSPEC-
TION 1.
CONDITION 107: AN-
TI-FRET STRIP IS
NOT MISSING AND
ANTI-FRET STRIP IS
NOT MADE FROM
PHENOLIC MATERIAL
AND NO DAMAGE
FOUND ON THE ANTI-
FRET STRIP during
INSPECTION 2 (a)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 25, 2017
737-57A1338 RB
11 of 161
REQUIREMENTS BULLETIN 737-57A1338
ALERTALERT

### Page 12

Group 2; Group 3, Configuration 1:
Table 1: Detailed Inspections and NDT Inspections of the Outboard Flap Tracks at Positions 1 and 8
Repeat Inter-
val (Not to Ex-
ceed)
Compliance Time (Whichever Occurs Later)ActionCondition
-Before further flight.ACTION 1: Re-
move the tapered
shim and install a
new tapered shim.
CONDITION 108: TA-
PERED SHIM IS
MISSING OR TA-
PERED SHIM IS MADE
FROM LAMINATED
MATERIAL OR WIDTH
OF TAPERED SHIM IS
LESS THAN 1.70
INCHES OR ANY
DAMAGE OR ANY
CORROSION FOUND
ON THE TAPERED
SHIM during INSPEC-
TION 2 (a)
10,000 flap
track flight cy-
cles or 4 years,
whichever oc-
curs first.
-ACTION 2: Repeat
INSPECTION 1.
10,000 flap
track flight cy-
cles or 4 years,
whichever oc-
curs first.
-Repeat INSPEC-
TION 1.
CONDITION 109: TA-
PERED SHIM IS NOT
MISSING AND TA-
PERED SHIM IS NOT
MADE FROM LAMI-
NATED MATERIAL
AND WIDTH OF TA-
PERED SHIM IS 1.70
INCHES OR MORE
AND NO DAMAGE
AND NO CORROSION
FOUND ON THE TA-
PERED SHIM during
INSPECTION 2 (a)
-Before further flight.ACTION 1: Repair
the flap track.
CONDITION 110: ANY
CORROSION OR ANY
CRACK FOUND ON
THE FLAP TRACK
THAT IS IN THE RE-
PAIR LIMITS OF CMM
57-53-15 during IN-
SPECTION 2 (a)(c)
10,000 flap
track flight cy-
cles or 4 years,
whichever oc-
curs first.
-ACTION 2: Repeat
INSPECTION 1.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 25, 2017
737-57A1338 RB
12 of 161
REQUIREMENTS BULLETIN 737-57A1338
ALERTALERT

### Page 13

Group 2; Group 3, Configuration 1:
Table 1: Detailed Inspections and NDT Inspections of the Outboard Flap Tracks at Positions 1 and 8
Repeat Inter-
val (Not to Ex-
ceed)
Compliance Time (Whichever Occurs Later)ActionCondition
-Before further flight.Remove the flap
track and install a
new or serviceable
flap track. (b)
CONDITION 111: ANY
CORROSION OR ANY
CRACK FOUND ON
THE FLAP TRACK
THAT IS LARGER
THAN THE REPAIR
LIMITS OF CMM 57-
53-15 during INSPEC-
TION 2 (a)(c)
10,000 flap
track flight cy-
cles or 4 years,
whichever oc-
curs first.
-Repeat INSPEC-
TION 1.
CONDITION 112: NO
CORROSION AND NO
CRACK FOUND ON
THE FLAP TRACK
during INSPECTION 2
(a)
-Before further flight.ACTION 1: Re-
move the bushing
and install a new or
serviceable bush-
ing.
CONDITION 113: ANY
CORROSION FOUND
ON THE BUSHING
during INSPECTION 2
(a)
10,000 flap
track flight cy-
cles or 4 years,
whichever oc-
curs first.
-ACTION 2: Repeat
INSPECTION 1.
10,000 flap
track flight cy-
cles or 4 years,
whichever oc-
curs first.
-Repeat INSPEC-
TION 1.
CONDITION 114: NO
CORROSION FOUND
ON THE BUSHING
during INSPECTION 2
(a)
-Before further flight.Remove the flap
track and install a
new or serviceable
flap track. (b)
CONDITION 115: FLAP
TRACK CANNOT BE
PUT BACK TO A SER-
VICEABLE CONDI-
TION during overhaul
(a)
20,000 flap
track flight cy-
cles or 8 years,
whichever oc-
curs first.
-Repeat the over-
haul of the flap
track.
CONDITION 116: FLAP
TRACK FOUND SER-
VICEABLE OR PUT
BACK TO A SERVICE-
ABLE CONDITION
during overhaul (a)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 25, 2017
737-57A1338 RB
13 of 161
REQUIREMENTS BULLETIN 737-57A1338
ALERTALERT

### Page 14

Group 2; Group 3, Configuration 1:
Table 1: Detailed Inspections and NDT Inspections of the Outboard Flap Tracks at Positions 1 and 8
Repeat Inter-
val (Not to Ex-
ceed)
Compliance Time (Whichever Occurs Later)ActionCondition
(a) More than one CONDITION can be applicable on each flap track.
(b) The replacement flap track, whether new or serviceable, must be in compliance with the initial inspection
requirements and compliance times based on the applicable flap track condition. Inspections and overhauls
previously accomplished in accordance with Requirements Bulletin 737-57A1338 RB can be used to sat-
isfy these requirements, so long as the track continues to comply with repeat intervals specified in the table.
For Group 3 airplanes, replacement of the flap track could result in a change in Configuration. Comply
with all requirements specified in the table for the Configuration of the flap track installed.
(c) CMM 57-53-15, Revision 44, dated March 1, 2016 and Temporary Revision 57-3003, dated August 18,
2017, or later revisions.
Group 3, Configuration 2:
The actions required for each INSPECTION in Table 2 are identified as follows:
Group 3, Configuration 2:
ActionTitle
ACTION 1: Do a detailed inspection of the flap track flanges and webs for any crack,
any nick, any corrosion pit, any galling, any piece broken off, and any stop-drill repair.
INSPECTION 3
ACTION 2: Do a surface High Frequency Eddy Current (HFEC) inspection of the flap
track flanges and webs, and an open hole HFEC inspection of the flap track webs for
any crack.
ACTION 3: Do a surface HFEC inspection and an ultrasonic inspection of the upper
flap track flange for any crack.
ACTION 4: Do a detailed inspection of the anti-fret strip and the tapered shim for any
damage and any corrosion.
ACTION 5: Do a detailed inspection of the flap track at the rear spar attachment for
any crack, any corrosion and any loose fastener.
ACTION 1: Do a detailed inspection of the anti-fret strip for presence or absence of
the anti-fret strip and for any damage and for material.
INSPECTION 4
ACTION 2: Do a detailed inspection of the tapered shim for presence or absence, any
damage, any corrosion, and for material, and measure the width of the tapered shim
normal to its aft edge.
ACTION 3: Do a detailed inspection of the flap track in the area of the rear spar attach-
ment mating surface for any corrosion.
ACTION 4: Do a detailed inspection of the outer circumferential surface of the bushing
for any corrosion.
ACTION 5: Do a surface HFEC inspection and an open hole HFEC inspection of the
flap track for any crack.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 25, 2017
737-57A1338 RB
14 of 161
REQUIREMENTS BULLETIN 737-57A1338
ALERTALERT

### Page 15

Group 3, Configuration 2:
Table 2: Detailed Inspections and NDT Inspections of the Outboard Flap Tracks at Positions 1 and 8
Repeat Inter-
val (Not to Ex-
ceed)
Compliance Time (Whichever Occurs Later)ActionCondition
-Within 6
months after
the original is-
sue date of Re-
quirements
Bulletin 737-
57A1338 RB.
Within 5,000 flap track flight cy-
cles or 2 years, whichever oc-
curs first, after the most recent
overhaul of the affected flap
track.
ACTION 1: Do IN-
SPECTION 3 on
each affected flap
track.
Airplanes with flap
tracks that have known
maintenance records
and on which an over-
haul was done
-Within 6
months after
the original is-
sue date of Re-
quirements
Bulletin 737-
57A1338 RB.
Whichever Occurs FirstACTION 2: Do an
overhaul of each
affected flap track. Within 10,000flap track flight
cycles or 4
years,
whichever oc-
curs first, after
the first inspec-
tion of the af-
fected flap
track in accor-
dance with Re-
quirements
Bulletin 737-
57A1338 RB.
Within 20,000
flap track flight
cycles or 8
years,
whichever oc-
curs first, after
the most re-
cent overhaul
of the affected
flap track.
-Within 6
months after
the original is-
sue date of Re-
quirements
Bulletin 737-
57A1338 RB.
Within 10,000 flap track flight
cycles or 4 years, whichever
occurs first, since the affected
flap track was new.
ACTION 1: Do IN-
SPECTION 3 on
each affected flap
track.
Airplanes with flap
tracks that have known
maintenance records
and on which no over-
haul was done
-Within 6
months after
the original is-
sue date of Re-
quirements
Bulletin 737-
57A1338 RB.
Within 20,000 flap track flight
cycles or 8 years, whichever
occurs first, since the affected
flap track was new.
ACTION 2: Do an
overhaul of each
affected flap track.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 25, 2017
737-57A1338 RB
15 of 161
REQUIREMENTS BULLETIN 737-57A1338
ALERTALERT

### Page 16

Group 3, Configuration 2:
Table 2: Detailed Inspections and NDT Inspections of the Outboard Flap Tracks at Positions 1 and 8
Repeat Inter-
val (Not to Ex-
ceed)
Compliance Time (Whichever Occurs Later)ActionCondition
-Within 6 months after the original issue date of
Requirements Bulletin 737-57A1338 RB.
ACTION 1: Do IN-
SPECTION 3 on
each affected flap
track.
Airplanes with flap
tracks that have un-
known maintenance
records
-Within 6 months after the original issue date of
Requirements Bulletin 737-57A1338 RB.
ACTION 2: Do an
overhaul of each
affected flap track.
-Before further flight.Remove the flap
track and install a
new or serviceable
flap track. (b)
CONDITION 201: ANY
CRACK, ANY NICK,
ANY CORROSION PIT,
ANY GALLING, ANY
PIECE BROKEN OFF
OR ANY STOP-DRILL
REPAIR FOUND during
INSPECTION 3 (a)
10,000 flap
track flight cy-
cles or 4 years,
whichever oc-
curs first.
-Repeat INSPEC-
TION 3.
CONDITION 202: NO
CRACK, NO NICK, NO
CORROSION PIT, NO
GALLING, NO PIECE
BROKEN OFF AND
NO STOP-DRILL RE-
PAIR FOUND during
INSPECTION 3 (a)
-Before further flight.ACTION 1: Do IN-
SPECTION 4 and
all applicable relat-
ed corrective ac-
tions.
CONDITION 203: ANY
DAMAGE OR ANY
CORROSION FOUND
ON THE ANTI-FRET
STRIP OR ON THE
TAPERED SHIM; OR
ANY CORROSION OR
ANY LOOSE FASTEN-
ER FOUND ON THE
FLAP TRACK AT THE
REAR SPAR ATTACH-
MENT during INSPEC-
TION 3 (a)
-Before further flight.ACTION 2: Install
the repaired flap
track, or a new or
serviceable flap
track. (b)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 25, 2017
737-57A1338 RB
16 of 161
REQUIREMENTS BULLETIN 737-57A1338
ALERTALERT

### Page 17

Group 3, Configuration 2:
Table 2: Detailed Inspections and NDT Inspections of the Outboard Flap Tracks at Positions 1 and 8
Repeat Inter-
val (Not to Ex-
ceed)
Compliance Time (Whichever Occurs Later)ActionCondition
10,000 flap
track flight cy-
cles or 4 years,
whichever oc-
curs first.
-Repeat INSPEC-
TION 3.
CONDITION 204: NO
DAMAGE AND NO
CORROSION FOUND
ON THE ANTI-FRET
STRIP AND ON THE
TAPERED SHIM; AND
NO CORROSION AND
NO LOOSE FASTEN-
ER FOUND ON THE
FLAP TRACK AT THE
REAR SPAR ATTACH-
MENT during INSPEC-
TION 3 (a)
-Before further flight.ACTION 1: Re-
move the anti-fret
strip and install a
new anti-fret strip.
CONDITION 205: AN-
TI-FRET STRIP IS
MISSING OR ANTI-
FRET STRIP IS MADE
FROM PHENOLIC MA-
TERIAL OR ANY DAM-
AGE FOUND ON THE
ANTI-FRET STRIP
during INSPECTION 4
(a)
10,000 flap
track flight cy-
cles or 4 years,
whichever oc-
curs first.
-ACTION 2: Repeat
INSPECTION 3.
10,000 flap
track flight cy-
cles or 4 years,
whichever oc-
curs first.
-Repeat INSPEC-
TION 3.
CONDITION 206: AN-
TI-FRET STRIP IS
NOT MISSING AND
ANTI-FRET STRIP IS
NOT MADE FROM
PHENOLIC MATERIAL
AND NO DAMAGE
FOUND ON THE ANTI-
FRET STRIP during
INSPECTION 4 (a)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 25, 2017
737-57A1338 RB
17 of 161
REQUIREMENTS BULLETIN 737-57A1338
ALERTALERT

### Page 18

Group 3, Configuration 2:
Table 2: Detailed Inspections and NDT Inspections of the Outboard Flap Tracks at Positions 1 and 8
Repeat Inter-
val (Not to Ex-
ceed)
Compliance Time (Whichever Occurs Later)ActionCondition
-Before further flight.ACTION 1: Re-
move the tapered
shim and install a
new tapered shim.
CONDITION 207: TA-
PERED SHIM IS
MISSING OR TA-
PERED SHIM IS MADE
FROM LAMINATED
MATERIAL OR WIDTH
OF TAPERED SHIM IS
LESS THAN 1.70
INCHES OR ANY
DAMAGE OR ANY
CORROSION FOUND
ON THE TAPERED
SHIM during INSPEC-
TION 4 (a)
10,000 flap
track flight cy-
cles or 4 years,
whichever oc-
curs first.
-ACTION 2: Repeat
INSPECTION 3.
10,000 flap
track flight cy-
cles or 4 years,
whichever oc-
curs first.
-Repeat INSPEC-
TION 3.
CONDITION 208: TA-
PERED SHIM IS NOT
MISSING AND TA-
PERED SHIM IS NOT
MADE FROM LAMI-
NATED MATERIAL
AND WIDTH OF TA-
PERED SHIM IS 1.70
INCHES OR MORE
AND NO DAMAGE
AND NO CORROSION
FOUND ON THE TA-
PERED SHIM during
INSPECTION 4 (a)
-Before further flight.ACTION 1: Repair
the flap track.
CONDITION 209: ANY
CORROSION OR ANY
CRACK FOUND ON
THE FLAP TRACK
THAT IS IN THE RE-
PAIR LIMITS OF CMM
57-53-15 during IN-
SPECTION 4 (a)(c)
10,000 flap
track flight cy-
cles or 4 years,
whichever oc-
curs first.
-ACTION 2: Repeat
INSPECTION 3.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 25, 2017
737-57A1338 RB
18 of 161
REQUIREMENTS BULLETIN 737-57A1338
ALERTALERT

### Page 19

Group 3, Configuration 2:
Table 2: Detailed Inspections and NDT Inspections of the Outboard Flap Tracks at Positions 1 and 8
Repeat Inter-
val (Not to Ex-
ceed)
Compliance Time (Whichever Occurs Later)ActionCondition
-Before further flight.Remove the flap
track and install a
new or serviceable
flap track. (b)
CONDITION 210: ANY
CORROSION OR ANY
CRACK FOUND ON
THE FLAP TRACK
THAT IS LARGER
THAN THE REPAIR
LIMITS OF CMM 57-
53-15 during INSPEC-
TION 4 (a)(c)
10,000 flap
track flight cy-
cles or 4 years,
whichever oc-
curs first.
-Repeat INSPEC-
TION 3.
CONDITION 211: NO
CORROSION AND NO
CRACK FOUND ON
THE FLAP TRACK
during INSPECTION 4
(a)
-Before further flight.ACTION 1: Re-
move the bushing
and install a new or
serviceable bush-
ing.
CONDITION 212: ANY
CORROSION FOUND
ON THE BUSHING
during INSPECTION 4
(a)
10,000 flap
track flight cy-
cles or 4 years,
whichever oc-
curs first.
-ACTION 2: Repeat
INSPECTION 3.
10,000 flap
track flight cy-
cles or 4 years,
whichever oc-
curs first.
-Repeat INSPEC-
TION 3.
CONDITION 213: NO
CORROSION FOUND
ON THE BUSHING
during INSPECTION 4
(a)
-Before further flight.Remove the flap
track and install a
new or serviceable
flap track. (b)
CONDITION 214: FLAP
TRACK CANNOT BE
PUT BACK TO A SER-
VICEABLE CONDI-
TION during overhaul
(a)
20,000 flap
track flight cy-
cles or 8 years,
whichever oc-
curs first.
-Repeat the over-
haul of the flap
track.
CONDITION 215: FLAP
TRACK FOUND SER-
VICEABLE OR PUT
BACK TO A SERVICE-
ABLE CONDITION
during overhaul (a)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 25, 2017
737-57A1338 RB
19 of 161
REQUIREMENTS BULLETIN 737-57A1338
ALERTALERT

### Page 20

Group 3, Configuration 2:
Table 2: Detailed Inspections and NDT Inspections of the Outboard Flap Tracks at Positions 1 and 8
Repeat Inter-
val (Not to Ex-
ceed)
Compliance Time (Whichever Occurs Later)ActionCondition
(a) More than one CONDITION can be applicable on each flap track.
(b) The replacement flap track, whether new or serviceable, must be in compliance with the initial inspection
requirements and compliance times based on the applicable flap track condition. Inspections and overhauls
previously accomplished in accordance with Requirements Bulletin 737-57A1338 RB can be used to sat-
isfy these requirements, so long as the track continues to comply with repeat intervals specified in the table.
For Group 3 airplanes, replacement of the flap track could result in a change in Configuration. Comply
with all requirements specified in the table for the Configuration of the flap track installed.
(c) CMM 57-53-15, Revision 44, dated March 1, 2016 and Temporary Revision 57-3003, dated August 18,
2017, or later revisions.
Group 2; Group 3, Configuration 1:
The actions required for each INSPECTION in Table 3 are identified as follows:
Group 2; Group 3, Configuration 1:
ActionTitle
Do a surface HFEC inspection of the flap track flanges and webs for any crack.INSPECTION 5
ACTION 1: Inspect the flap track assembly for part number. As an alternative to the
inspection, a review of the maintenance records can be used if the part number of the
flap track assembly can be positively determined.
INSPECTION 6 (a)
ACTION 2: Do a detailed inspection of the flap track flanges and webs for any crack,
any nick, any corrosion pit, any galling, any piece broken off, and any stop-drill repair.
ACTION 3: Do a surface HFEC inspection of the flap track flanges and webs for any
crack.
ACTION 4: Do a surface HFEC inspection and an ultrasonic inspection of the upper
flap track flange for any crack.
ACTION 5: Do a detailed inspection of the anti-fret strip and the tapered shim for any
damage and any corrosion.
ACTION 6: Do a detailed inspection of the flap track at the rear spar attachment for
any crack, any corrosion and any loose fastener.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 25, 2017
737-57A1338 RB
20 of 161
REQUIREMENTS BULLETIN 737-57A1338
ALERTALERT

### Page 21

Group 2; Group 3, Configuration 1:
ActionTitle
ACTION 1: Do a detailed inspection of the anti-fret strip for presence or absence of
the anti-fret strip and for any damage and for material.
INSPECTION 7 (a)
ACTION 2: Do a detailed inspection of the tapered shim for presence or absence, any
damage, any corrosion, and for material, and measure the width of the tapered shim
normal to its aft edge.
ACTION 3: Do a detailed inspection of the flap track in the area of the rear spar attach-
ment mating surface for any corrosion.
ACTION 4: Do a detailed inspection of the outer circumferential surface of the bushing
for any corrosion.
ACTION 5: Do a surface HFEC inspection and an open hole HFEC inspection of the
flap track for any crack.
(a) This INSPECTION is related to SB 737-57A1271.
Group 2; Group 3, Configuration 1:
Table 3: Detailed Inspections and NDT Inspections of the Outboard Flap Tracks at Positions 2 and 7
Repeat Inter-
val (Not to Ex-
ceed)
Compliance Time (Whichever Occurs Later)ActionCondition
-Within 6
months after
the original is-
sue date of Re-
quirements
Bulletin 737-
57A1338 RB.
Within 5,000 flap track flight cy-
cles or 2 years, whichever oc-
curs first, after the most recent
overhaul of the affected flap
track.
ACTION 1: Do IN-
SPECTION 5 on
each affected flap
track.
Airplanes with flap
tracks on which an
overhaul was done
-Within 6
months after
the original is-
sue date of Re-
quirements
Bulletin 737-
57A1338 RB.
Within 10,000 flap track flight
cycles or 4 years, whichever
occurs first, after the most re-
cent inspection of the affected
flap track in accordance with SB
737-57A1271.
ACTION 2: Do IN-
SPECTION 6 on
each affected flap
track.
-Within 6
months after
the original is-
sue date of Re-
quirements
Bulletin 737-
57A1338 RB.
Within 20,000 flap track flight
cycles or 8 years, whichever
occurs first, after the most re-
cent overhaul of the affected
flap track.
ACTION 3: Do an
overhaul of each
affected flap track.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 25, 2017
737-57A1338 RB
21 of 161
REQUIREMENTS BULLETIN 737-57A1338
ALERTALERT

### Page 22

Group 2; Group 3, Configuration 1:
Table 3: Detailed Inspections and NDT Inspections of the Outboard Flap Tracks at Positions 2 and 7
Repeat Inter-
val (Not to Ex-
ceed)
Compliance Time (Whichever Occurs Later)ActionCondition
-Within 6
months after
the original is-
sue date of Re-
quirements
Bulletin 737-
57A1338 RB.
Within 10,000 flap track flight
cycles or 4 years, whichever
occurs first, since the affected
flap track was new.
ACTION 1: Do IN-
SPECTION 5 on
each affected flap
track.
Airplanes with flap
tracks on which no
overhaul was done and
no inspection was done
in accordance with SB
737-57A1271
-Within 6
months after
the original is-
sue date of Re-
quirements
Bulletin 737-
57A1338 RB.
Within 10,000 flap track flight
cycles or 4 years, whichever
occurs first, since the affected
flap track was new.
ACTION 2: Do IN-
SPECTION 6 on
each affected flap
track.
-Within 6
months after
the original is-
sue date of Re-
quirements
Bulletin 737-
57A1338 RB.
Within 20,000 flap track flight
cycles or 8 years, whichever
occurs first, since the affected
flap track was new.
ACTION 3: Do an
overhaul of each
affected flap track.
-Within 6
months after
the original is-
sue date of Re-
quirements
Bulletin 737-
57A1338 RB.
Within 10,000 flap track flight
cycles or 4 years, whichever
occurs first, since the affected
flap track was new.
ACTION 1: Do IN-
SPECTION 5 on
each affected flap
track.
Airplanes with flap
tracks on which no
overhaul was done, and
an inspection was done
in accordance with SB
737-57A1271
-Within 6
months after
the original is-
sue date of Re-
quirements
Bulletin 737-
57A1338 RB.
Within 10,000 flap track flight
cycles or 4 years, whichever
occurs first, after the most re-
cent inspection of the affected
flap track in accordance with SB
737-57A1271.
ACTION 2: Do IN-
SPECTION 6 on
each affected flap
track.
-Within 6
months after
the original is-
sue date of Re-
quirements
Bulletin 737-
57A1338 RB.
Within 20,000 flap track flight
cycles or 8 years, whichever
occurs first, since the affected
flap track was new.
ACTION 3: Do an
overhaul of each
affected flap track.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 25, 2017
737-57A1338 RB
22 of 161
REQUIREMENTS BULLETIN 737-57A1338
ALERTALERT

### Page 23

Group 2; Group 3, Configuration 1:
Table 3: Detailed Inspections and NDT Inspections of the Outboard Flap Tracks at Positions 2 and 7
Repeat Inter-
val (Not to Ex-
ceed)
Compliance Time (Whichever Occurs Later)ActionCondition
-Before further flight.Remove the flap
track and install a
new or serviceable
flap track. (b)
CONDITION 301: FLAP
TRACK ASSEMBLY
PART NUMBER IS 65-
46428-31 OR 65-
46428-33 (a)
-Before further flight.Remove the flap
track and install a
new or serviceable
flap track. (b)
CONDITION 302: ANY
CRACK, ANY NICK,
ANY CORROSION PIT,
ANY GALLING, ANY
PIECE BROKEN OFF
OR ANY STOP-DRILL
REPAIR FOUND during
INSPECTION 5 or IN-
SPECTION 6 (a)
10,000 flap
track flight cy-
cles or 4 years,
whichever oc-
curs first.
-Repeat INSPEC-
TION 5 and IN-
SPECTION 6.
CONDITION 303: NO
CRACK, NO NICK, NO
CORROSION PIT, NO
GALLING, NO PIECE
BROKEN OFF AND
NO STOP-DRILL RE-
PAIR FOUND during
INSPECTION 5 or IN-
SPECTION 6 (a)
-Before further flight.ACTION 1: Do IN-
SPECTION 7 and
all applicable relat-
ed corrective ac-
tions.
CONDITION 304: ANY
DAMAGE OR ANY
CORROSION FOUND
ON THE ANTI-FRET
STRIP OR ON THE
TAPERED SHIM; OR
ANY CORROSION OR
ANY LOOSE FASTEN-
ER FOUND ON THE
FLAP TRACK AT THE
REAR SPAR ATTACH-
MENT during INSPEC-
TION 6 (a)
-Before further flight.ACTION 2: Install
the repaired flap
track, or a new or
serviceable flap
track. (b)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 25, 2017
737-57A1338 RB
23 of 161
REQUIREMENTS BULLETIN 737-57A1338
ALERTALERT

### Page 24

Group 2; Group 3, Configuration 1:
Table 3: Detailed Inspections and NDT Inspections of the Outboard Flap Tracks at Positions 2 and 7
Repeat Inter-
val (Not to Ex-
ceed)
Compliance Time (Whichever Occurs Later)ActionCondition
10,000 flap
track flight cy-
cles or 4 years,
whichever oc-
curs first.
-Repeat INSPEC-
TION 5 and IN-
SPECTION 6.
CONDITION 305: NO
DAMAGE AND NO
CORROSION FOUND
ON THE ANTI-FRET
STRIP AND ON THE
TAPERED SHIM; AND
NO CORROSION AND
NO LOOSE FASTEN-
ER FOUND ON THE
FLAP TRACK AT THE
REAR SPAR ATTACH-
MENT during INSPEC-
TION 6 (a)
-Before further flight.ACTION 1: Re-
move the anti-fret
strip and install a
new anti-fret strip.
CONDITION 306: AN-
TI-FRET STRIP IS
MISSING OR ANTI-
FRET STRIP IS MADE
FROM PHENOLIC MA-
TERIAL OR ANY DAM-
AGE FOUND ON THE
ANTI-FRET STRIP
during INSPECTION 7
(a)
10,000 flap
track flight cy-
cles or 4 years,
whichever oc-
curs first.
-ACTION 2: Repeat
INSPECTION 5
and INSPECTION
6.
10,000 flap
track flight cy-
cles or 4 years,
whichever oc-
curs first.
-Repeat INSPEC-
TION 5 and IN-
SPECTION 6.
CONDITION 307: AN-
TI-FRET STRIP IS
NOT MISSING AND
ANTI-FRET STRIP IS
NOT MADE FROM
PHENOLIC MATERIAL
AND NO DAMAGE
FOUND ON THE ANTI-
FRET STRIP during
INSPECTION 7 (a)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 25, 2017
737-57A1338 RB
24 of 161
REQUIREMENTS BULLETIN 737-57A1338
ALERTALERT

### Page 25

Group 2; Group 3, Configuration 1:
Table 3: Detailed Inspections and NDT Inspections of the Outboard Flap Tracks at Positions 2 and 7
Repeat Inter-
val (Not to Ex-
ceed)
Compliance Time (Whichever Occurs Later)ActionCondition
-Before further flight.ACTION 1: Re-
move the tapered
shim and install a
new tapered shim.
CONDITION 308: TA-
PERED SHIM IS
MISSING OR TA-
PERED SHIM IS MADE
FROM LAMINATED
MATERIAL OR WIDTH
OF TAPERED SHIM IS
LESS THAN 1.70
INCHES OR ANY
DAMAGE OR ANY
CORROSION FOUND
ON THE TAPERED
SHIM during INSPEC-
TION 7 (a)
10,000 flap
track flight cy-
cles or 4 years,
whichever oc-
curs first.
-ACTION 2: Repeat
INSPECTION 5
and INSPECTION
6.
10,000 flap
track flight cy-
cles or 4 years,
whichever oc-
curs first.
-Repeat INSPEC-
TION 5 and IN-
SPECTION 6.
CONDITION 309: TA-
PERED SHIM IS NOT
MISSING AND TA-
PERED SHIM IS NOT
MADE FROM LAMI-
NATED MATERIAL
AND WIDTH OF TA-
PERED SHIM IS 1.70
INCHES OR MORE
AND NO DAMAGE
AND NO CORROSION
FOUND ON THE TA-
PERED SHIM during
INSPECTION 7 (a)
-Before further flight.ACTION 1: Repair
the flap track.
CONDITION 310: ANY
CORROSION OR ANY
CRACK FOUND ON
THE FLAP TRACK
THAT IS IN THE RE-
PAIR LIMITS OF CMM
57-53-15 during IN-
SPECTION 7 (a)(c)
10,000 flap
track flight cy-
cles or 4 years,
whichever oc-
curs first.
-ACTION 2: Repeat
INSPECTION 5
and INSPECTION
6.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 25, 2017
737-57A1338 RB
25 of 161
REQUIREMENTS BULLETIN 737-57A1338
ALERTALERT

### Page 26

Group 2; Group 3, Configuration 1:
Table 3: Detailed Inspections and NDT Inspections of the Outboard Flap Tracks at Positions 2 and 7
Repeat Inter-
val (Not to Ex-
ceed)
Compliance Time (Whichever Occurs Later)ActionCondition
-Before further flight.Remove the flap
track and install a
new or serviceable
flap track. (b)
CONDITION 311: ANY
CORROSION OR ANY
CRACK FOUND ON
THE FLAP TRACK
THAT IS LARGER
THAN THE REPAIR
LIMITS OF CMM 57-
53-15 during INSPEC-
TION 7 (a)(c)
10,000 flap
track flight cy-
cles or 4 years,
whichever oc-
curs first.
-Repeat INSPEC-
TION 5 and IN-
SPECTION 6.
CONDITION 312: NO
CORROSION AND NO
CRACK FOUND ON
THE FLAP TRACK
during INSPECTION 7
(a)
-Before further flight.ACTION 1: Re-
move the bushing
and install a new or
serviceable bush-
ing.
CONDITION 313: ANY
CORROSION FOUND
ON THE BUSHING
during INSPECTION 7
(a)
10,000 flap
track flight cy-
cles or 4 years,
whichever oc-
curs first.
-ACTION 2: Repeat
INSPECTION 5
and INSPECTION
6.
10,000 flap
track flight cy-
cles or 4 years,
whichever oc-
curs first.
-Repeat INSPEC-
TION 5 and IN-
SPECTION 6.
CONDITION 314: NO
CORROSION FOUND
ON THE BUSHING
during INSPECTION 7
(a)
-Before further flight.Remove the flap
track and install a
new or serviceable
flap track. (b)
CONDITION 315: FLAP
TRACK CANNOT BE
PUT BACK TO A SER-
VICEABLE CONDI-
TION during overhaul
(a)
20,000 flap
track flight cy-
cles or 8 years,
whichever oc-
curs first.
-Repeat the over-
haul of the flap
track.
CONDITION 316: FLAP
TRACK FOUND SER-
VICEABLE OR PUT
BACK TO A SERVICE-
ABLE CONDITION
during overhaul (a)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 25, 2017
737-57A1338 RB
26 of 161
REQUIREMENTS BULLETIN 737-57A1338
ALERTALERT

### Page 27

Group 2; Group 3, Configuration 1:
Table 3: Detailed Inspections and NDT Inspections of the Outboard Flap Tracks at Positions 2 and 7
Repeat Inter-
val (Not to Ex-
ceed)
Compliance Time (Whichever Occurs Later)ActionCondition
(a) More than one CONDITION can be applicable on each flap track.
(b) The replacement flap track, whether new or serviceable, must be in compliance with the initial inspection
requirements and compliance times based on the applicable flap track condition. Inspections and overhauls
previously accomplished in accordance with Requirements Bulletin 737-57A1338 RB can be used to sat-
isfy these requirements, so long as the track continues to comply with repeat intervals specified in the table.
For Group 3 airplanes, replacement of the flap track could result in a change in Configuration. Comply
with all requirements specified in the table for the Configuration of the flap track installed.
(c) CMM 57-53-15, Revision 44, dated March 1, 2016 and Temporary Revision 57-3003, dated August 18,
2017, or later revisions.
Group 3, Configuration 2:
The actions required for each INSPECTION in Table 4 are identified as follows:
Group 3, Configuration 2:
ActionTitle
Do a surface HFEC inspection of the flap track flanges and webs, and an open hole
HFEC inspection of the flap track webs for any crack.
INSPECTION 8
ACTION 1: Do a detailed inspection of the flap track flanges and webs for any crack,
any nick, any corrosion pit, any galling, any piece broken off, and any stop-drill repair.
INSPECTION 9 (a)
ACTION 2: Do a surface HFEC inspection of the flap track flanges and webs for any
crack.
ACTION 3: Do a surface HFEC inspection and an ultrasonic inspection of the upper
flap track flange for any crack.
ACTION 4: Do a detailed inspection of the anti-fret strip and the tapered shim for any
damage and any corrosion.
ACTION 5: Do a detailed inspection of the flap track at the rear spar attachment for
any crack, any corrosion and any loose fastener.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 25, 2017
737-57A1338 RB
27 of 161
REQUIREMENTS BULLETIN 737-57A1338
ALERTALERT

### Page 28

Group 3, Configuration 2:
ActionTitle
ACTION 1: Do a detailed inspection of the anti-fret strip for presence or absence of
the anti-fret strip and for any damage and for material.
INSPECTION 10 (a)
ACTION 2: Do a detailed inspection of the tapered shim for presence or absence, any
damage, any corrosion, and for material, and measure the width of the tapered shim
normal to its aft edge.
ACTION 3: Do a detailed inspection of the flap track in the area of the rear spar attach-
ment mating surface for any corrosion.
ACTION 4: Do a detailed inspection of the outer circumferential surface of the bushing
for any corrosion.
ACTION 5: Do a surface HFEC inspection and an open hole HFEC inspection of the
flap track for any crack.
(a) This INSPECTION is related to SB 737-57A1271.
Group 3, Configuration 2:
Table 4: Detailed Inspections and NDT Inspections of the Outboard Flap Tracks at Positions 2 and 7
Repeat Inter-
val (Not to Ex-
ceed)
Compliance Time (Whichever Occurs Later)ActionCondition
-Within 6
months after
the original is-
sue date of Re-
quirements
Bulletin 737-
57A1338 RB.
Within 5,000 flap track flight cy-
cles or 2 years, whichever oc-
curs first, after the most recent
overhaul of the affected flap
track.
ACTION 1: Do IN-
SPECTION 8 on
each affected flap
track.
Airplanes with flap
tracks on which an
overhaul was done
-Within 6
months after
the original is-
sue date of Re-
quirements
Bulletin 737-
57A1338 RB.
Within 10,000 flap track flight
cycles or 4 years, whichever
occurs first, after the most re-
cent inspection of the affected
flap track in accordance with SB
737-57A1271.
ACTION 2: Do IN-
SPECTION 9 on
each affected flap
track.
-Within 6
months after
the original is-
sue date of Re-
quirements
Bulletin 737-
57A1338 RB.
Within 20,000 flap track flight
cycles or 8 years, whichever
occurs first, after the most re-
cent overhaul of the affected
flap track.
ACTION 3: Do an
overhaul of each
affected flap track.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 25, 2017
737-57A1338 RB
28 of 161
REQUIREMENTS BULLETIN 737-57A1338
ALERTALERT

### Page 29

Group 3, Configuration 2:
Table 4: Detailed Inspections and NDT Inspections of the Outboard Flap Tracks at Positions 2 and 7
Repeat Inter-
val (Not to Ex-
ceed)
Compliance Time (Whichever Occurs Later)ActionCondition
-Within 6
months after
the original is-
sue date of Re-
quirements
Bulletin 737-
57A1338 RB.
Within 10,000 flap track flight
cycles or 4 years, whichever
occurs first, since the affected
flap track was new.
ACTION 1: Do IN-
SPECTION 8 on
each affected flap
track.
Airplanes with flap
tracks on which no
overhaul was done and
no inspection was done
in accordance with SB
737-57A1271
-Within 6
months after
the original is-
sue date of Re-
quirements
Bulletin 737-
57A1338 RB.
Within 10,000 flap track flight
cycles or 4 years, whichever
occurs first, since the affected
flap track was new.
ACTION 2: Do IN-
SPECTION 9 on
each affected flap
track.
-Within 6
months after
the original is-
sue date of Re-
quirements
Bulletin 737-
57A1338 RB.
Within 20,000 flap track flight
cycles or 8 years, whichever
occurs first, since the affected
flap track was new.
ACTION 3: Do an
overhaul of each
affected flap track.
-Within 6
months after
the original is-
sue date of Re-
quirements
Bulletin 737-
57A1338 RB.
Within 10,000 flap track flight
cycles or 4 years, whichever
occurs first, since the affected
flap track was new.
ACTION 1: Do IN-
SPECTION 8 on
each affected flap
track.
Airplanes with flap
tracks on which no
overhaul was done and
an inspection was done
in accordance with SB
737-57A1271
-Within 6
months after
the original is-
sue date of Re-
quirements
Bulletin 737-
57A1338 RB.
Within 10,000 flap track flight
cycles or 4 years, whichever
occurs first, after the most re-
cent inspection of the affected
flap track in accordance with SB
737-57A1271.
ACTION 2: Do IN-
SPECTION 9 on
each affected flap
track.
-Within 6
months after
the original is-
sue date of Re-
quirements
Bulletin 737-
57A1338 RB.
Within 20,000 flap track flight
cycles or 8 years, whichever
occurs first, since the affected
flap track was new.
ACTION 3: Do an
overhaul of each
affected flap track.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 25, 2017
737-57A1338 RB
29 of 161
REQUIREMENTS BULLETIN 737-57A1338
ALERTALERT

### Page 30

Group 3, Configuration 2:
Table 4: Detailed Inspections and NDT Inspections of the Outboard Flap Tracks at Positions 2 and 7
Repeat Inter-
val (Not to Ex-
ceed)
Compliance Time (Whichever Occurs Later)ActionCondition
-Before further flight.Remove the flap
track and install a
new or serviceable
flap track. (b)
CONDITION 401: ANY
CRACK, ANY NICK,
ANY CORROSION PIT,
ANY GALLING, ANY
PIECE BROKEN OFF
OR ANY STOP-DRILL
REPAIR FOUND during
INSPECTION 8 or IN-
SPECTION 9 (a)
10,000 flap
track flight cy-
cles or 4 years,
whichever oc-
curs first.
-Repeat INSPEC-
TION 8 and IN-
SPECTION 9.
CONDITION 402: NO
CRACK, NO NICK, NO
CORROSION PIT, NO
GALLING, NO PIECE
BROKEN OFF AND
NO STOP-DRILL RE-
PAIR FOUND during
INSPECTION 8 or IN-
SPECTION 9 (a)
-Before further flight.ACTION 1: Do IN-
SPECTION 10 and
all applicable relat-
ed corrective ac-
tions.
CONDITION 403: ANY
DAMAGE OR ANY
CORROSION FOUND
ON THE ANTI-FRET
STRIP OR ON THE
TAPERED SHIM; OR
ANY CORROSION OR
ANY LOOSE FASTEN-
ER FOUND ON THE
FLAP TRACK AT THE
REAR SPAR ATTACH-
MENT during INSPEC-
TION 9 (a)
-Before further flight.ACTION 2: Install
the repaired flap
track, or a new or
serviceable flap
track. (b)
10,000 flap
track flight cy-
cles or 4 years,
whichever oc-
curs first.
-Repeat INSPEC-
TION 8 and IN-
SPECTION 9.
CONDITION 404: NO
DAMAGE AND NO
CORROSION FOUND
ON THE ANTI-FRET
STRIP AND ON THE
TAPERED SHIM; AND
NO CORROSION AND
NO LOOSE FASTEN-
ER FOUND ON THE
FLAP TRACK AT THE
REAR SPAR ATTACH-
MENT during INSPEC-
TION 9 (a)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 25, 2017
737-57A1338 RB
30 of 161
REQUIREMENTS BULLETIN 737-57A1338
ALERTALERT

### Page 31

Group 3, Configuration 2:
Table 4: Detailed Inspections and NDT Inspections of the Outboard Flap Tracks at Positions 2 and 7
Repeat Inter-
val (Not to Ex-
ceed)
Compliance Time (Whichever Occurs Later)ActionCondition
-Before further flight.ACTION 1: Re-
move the anti-fret
strip and install a
new anti-fret strip.
CONDITION 405: AN-
TI-FRET STRIP IS
MISSING OR ANTI-
FRET STRIP IS MADE
FROM PHENOLIC MA-
TERIAL OR ANY DAM-
AGE FOUND ON THE
ANTI-FRET STRIP
during INSPECTION 10
(a)
10,000 flap
track flight cy-
cles or 4 years,
whichever oc-
curs first.
-ACTION 2: Repeat
INSPECTION 8
and INSPECTION
9.
10,000 flap
track flight cy-
cles or 4 years,
whichever oc-
curs first.
-Repeat INSPEC-
TION 8 and IN-
SPECTION 9.
CONDITION 406: AN-
TI-FRET STRIP IS
NOT MISSING AND
ANTI-FRET STRIP IS
NOT MADE FROM
PHENOLIC MATERIAL
AND NO DAMAGE
FOUND ON THE ANTI-
FRET STRIP during
INSPECTION 10 (a)
-Before further flight.ACTION 1: Re-
move the tapered
shim and install a
new tapered shim.
CONDITION 407: TA-
PERED SHIM IS
MISSING OR TA-
PERED SHIM IS MADE
FROM LAMINATED
MATERIAL OR WIDTH
OF TAPERED SHIM IS
LESS THAN 1.70
INCHES OR ANY
DAMAGE OR ANY
CORROSION FOUND
ON THE TAPERED
SHIM during INSPEC-
TION 10 (a)
10,000 flap
track flight cy-
cles or 4 years,
whichever oc-
curs first.
-ACTION 2: Repeat
INSPECTION 8
and INSPECTION
9.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 25, 2017
737-57A1338 RB
31 of 161
REQUIREMENTS BULLETIN 737-57A1338
ALERTALERT

### Page 32

Group 3, Configuration 2:
Table 4: Detailed Inspections and NDT Inspections of the Outboard Flap Tracks at Positions 2 and 7
Repeat Inter-
val (Not to Ex-
ceed)
Compliance Time (Whichever Occurs Later)ActionCondition
10,000 flap
track flight cy-
cles or 4 years,
whichever oc-
curs first.
-Repeat INSPEC-
TION 8 and IN-
SPECTION 9.
CONDITION 408: TA-
PERED SHIM IS NOT
MISSING AND TA-
PERED SHIM IS NOT
MADE FROM LAMI-
NATED MATERIAL
AND WIDTH OF TA-
PERED SHIM IS 1.70
INCHES OR MORE
AND NO DAMAGE
AND NO CORROSION
FOUND ON THE TA-
PERED SHIM during
INSPECTION 10 (a)
-Before further flight.ACTION 1: Repair
the flap track.
CONDITION 409: ANY
CORROSION OR ANY
CRACK FOUND ON
THE FLAP TRACK
THAT IS IN THE RE-
PAIR LIMITS OF CMM
57-53-15 during IN-
SPECTION 10 (a)(c)
10,000 flap
track flight cy-
cles or 4 years,
whichever oc-
curs first.
-ACTION 2: Repeat
INSPECTION 8
and INSPECTION
9.
-Before further flight.Remove the flap
track and install a
new or serviceable
flap track. (b)
CONDITION 410: ANY
CORROSION OR ANY
CRACK FOUND ON
THE FLAP TRACK
THAT IS LARGER
THAN THE REPAIR
LIMITS OF CMM 57-
53-15 during INSPEC-
TION 10 (a)(c)
10,000 flap
track flight cy-
cles or 4 years,
whichever oc-
curs first.
-Repeat INSPEC-
TION 8 and IN-
SPECTION 9.
CONDITION 411: NO
CORROSION AND NO
CRACK FOUND ON
THE FLAP TRACK
during INSPECTION 10
(a)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 25, 2017
737-57A1338 RB
32 of 161
REQUIREMENTS BULLETIN 737-57A1338
ALERTALERT

### Page 33

Group 3, Configuration 2:
Table 4: Detailed Inspections and NDT Inspections of the Outboard Flap Tracks at Positions 2 and 7
Repeat Inter-
val (Not to Ex-
ceed)
Compliance Time (Whichever Occurs Later)ActionCondition
-Before further flight.ACTION 1: Re-
move the bushing
and install a new or
serviceable bush-
ing.
CONDITION 412: ANY
CORROSION FOUND
ON THE BUSHING
during INSPECTION 10
(a)
10,000 flap
track flight cy-
cles or 4 years,
whichever oc-
curs first.
-ACTION 2: Repeat
INSPECTION 8
and INSPECTION
9.
10,000 flap
track flight cy-
cles or 4 years,
whichever oc-
curs first.
-Repeat INSPEC-
TION 8 and IN-
SPECTION 9.
CONDITION 413: NO
CORROSION FOUND
ON THE BUSHING
during INSPECTION 10
(a)
-Before further flight.Remove the flap
track and install a
new or serviceable
flap track. (b)
CONDITION 414: FLAP
TRACK CANNOT BE
PUT BACK TO A SER-
VICEABLE CONDI-
TION during overhaul
(a)
20,000 flap
track flight cy-
cles or 8 years,
whichever oc-
curs first.
-Repeat the over-
haul of the flap
track.
CONDITION 415: FLAP
TRACK FOUND SER-
VICEABLE OR PUT
BACK TO A SERVICE-
ABLE CONDITION
during overhaul (a)
(a) More than one CONDITION can be applicable on each flap track.
(b) The replacement flap track, whether new or serviceable, must be in compliance with the initial inspection
requirements and compliance times based on the applicable flap track condition. Inspections and overhauls
previously accomplished in accordance with Requirements Bulletin 737-57A1338 RB can be used to sat-
isfy these requirements, so long as the track continues to comply with repeat intervals specified in the table.
For Group 3 airplanes, replacement of the flap track could result in a change in Configuration. Comply
with all requirements specified in the table for the Configuration of the flap track installed.
(c) CMM 57-53-15, Revision 44, dated March 1, 2016 and Temporary Revision 57-3003, dated August 18,
2017, or later revisions.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 25, 2017
737-57A1338 RB
33 of 161
REQUIREMENTS BULLETIN 737-57A1338
ALERTALERT

### Page 34

4. APPROVAL
This Requirements Bulletin was examined by the Federal Aviation Administration (FAA). The changes
specified in this document comply with the applicable regulations and are FAA approved, as well as European
Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved
airplanes listed in the service bulletin effectivity. This document and its approval were based on the airplane
in its original Boeing delivery configuration or as modified by other Boeing changes.
If an airplane has a non-Boeing modification or repair that affects a component or system also affected by
this Requirements Bulletin, the operator is responsible for obtaining appropriate regulatory agency approval
before incorporating this Requirements Bulletin.
In addition, the Manager of the FAA Los Angeles Aircraft Certification Office approves the action (i.e.
inspection or modification) defined in this Requirements Bulletin as an alternative method of compliance to
the requirements of paragraphs (g), (h), (i), (j), (k), (l), (m), (n), (o), (p), (q), (r), (s), (t) and (u) of AD
2013-09-02. All provisions of AD 2013-09-02 that are not specifically referenced in the above statement
remain fully applicable and must be complied with.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 25, 2017
737-57A1338 RB
34 of 161
REQUIREMENTS BULLETIN 737-57A1338
ALERTALERT

### Page 35

5.    ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL INFORMATION
NOTE: 5. Unless shown differently, these dimensions and tolerances are used:
– Linear dimensions are in inches
– Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus
or minus 0.03 inch
– Tolerance on rivet and bolt edge margin is plus or minus 0.05 inch
– Angular tolerance is plus or minus 2 degrees
– Hole dimensions for standard solid rivets and fasteners are in Structural Repair
Manual (SRM) Chapter 51
– Torque Values:
— Values for structural fasteners are given in 737 Structural Repair Manual,
Chapter 51.
— Values for airframe maintenance tasks are included in Chapter 20 of 737
Aircraft Maintenance Manual (AMM).
— Values for electrical maintenance tasks are included in Chapter 20 of
Standard Wiring Practices Manual (SWPM).
— Values for engine maintenance tasks are included in Chapter 70 of 737
Aircraft Maintenance Manual (AMM).
— Non-standard torque values for maintenance tasks are included in the
applicable installation step.
6. Use the approved fastener, process and material substitutions in accordance with
SRM Chapter 51.
7. If the length of any fastener specified in this service bulletin does not meet installation
standards given in SRM Chapter 51, then a fastener of the same specification, or
an approved substitute, with a length which meets the installation standards given
in SRM Chapter 51 may be used. In addition, washers may be installed for fastener
grip length in accordance with SRM Chapter 51. Refer to SOPM 20-50-01 for alternate
full threaded fasteners (screws) needed for installation in this service bulletin.
8. A Detailed Inspection is defined as: An intensive examination of a specific item,
installation, or assembly to detect damage, failure, or irregularity. Available lighting
is normally supplemented with a direct source of good lighting at an intensity deemed
appropriate. Inspection aids such as mirrors, magnifying lenses, etc. may be
necessary. Surface cleaning and elaborate procedures may be required.
9. These work instructions refer to procedures included in other Boeing documents.
When the words "refer to" are used and the operator has an accepted alternative
procedure, the accepted alternative procedure can be used. When the words "in
accordance with" are included in the instruction, the procedure in the Boeing document
must be used.
10. The instructions in the Work Instructions and the figures can include operation of
tools or test equipment. Boeing Engineering Tool Drawings, the Illustrated Tool and
Equipment Manual, and the Special Tool and Ground Handling Drawing Index contain
data on versions of the tools or test equipment that you can use. It is permitted to
use replaced tools. It is not permitted to use superseded tools.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 25, 2017
737-57A1338 RB
35 of 161
REQUIREMENTS BULLETIN 737-57A1338
ALERTALERT

### Page 36

11. If it is necessary to remove more parts for access, you can remove those parts. If
you can get access without removing identified parts, it is not necessary to remove
all of the identified parts. Jacking and shoring limitations must be observed.
12. Where the work instructions include installation of a kept part, a new or serviceable
part with the same part number can be installed as an alternative to the kept part.
13. When more than one OPTION is given for a CONDITION, do only one of the OPTION
numbers. When more than one ACTION is given for a CONDITION number or an
OPTION number, do all of the ACTION numbers for that CONDITION number or
OPTION number.
14. This is an Enhanced Required for Compliance document. There will be a separate
Service Bulletin (SB) and a separate Requirements Bulletin (RB). If an RB is mandated
by an Airworthiness Directive (AD), then all applicable requirements specified in the
RB must be done. For the related SB, some locations are marked RC Start and RC
End to identify the requirements that are restated from the RB. For the related SB,
the areas between RC Start and RC End, including sub-steps and any figures
identified between RC Start and RC End, must be done to comply with the AD.
Therefore, an Alternative Method of Compliance (AMOC) is required for any deviations
to steps between RC Start and RC End, including substeps and identified figures.
For the related SB, the steps not between RC Start and RC End may be deviated
from using accepted methods in accordance with the operator's maintenance or
inspection program without obtaining approval of an AMOC; this is provided that the
steps between RC Start and RC End, including sub-steps and identified figures, can
still be done as specified, and the airplane can be put back in an airworthy condition.
Figures not required for compliance are omitted from the RB.
15. This is an Enhanced Required for Compliance document. The Boeing processes
used to create the Service Bulletin (SB) and the Requirements Bulletin (RB) ensure
that the information between "RC Start" and "RC End" in the SB are identical to the
information in the same sections (Compliance, Work Instructions...) of the RB which
the SB refers to as the related document.
16. Flap Track Position 1 is equivalent to left Wing Buttock Line (WBL) 355 and Flap
Track Position 8 is equivalent to right WBL 355.
17. Flap Track Position 2 is equivalent to left WBL 254 and Flap Track Position 7 is
equivalent to right WBL 254.
18. Conditions are numbered 1XX, 2XX, 3XX, and 4XX to designate which
Compliance/Work Instruction Table they appear on. CONDITION 1XX appears on
Table 1, CONDITION 2XX appears on Table 2, etc.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 25, 2017
737-57A1338 RB
36 of 161
REQUIREMENTS BULLETIN 737-57A1338
ALERTALERT

### Page 37

B. WORK INSTRUCTIONS
Actions Required for Compliance:
1. Requirements
Group 1:
Boeing endorses the FAA rules related to Limit of Validity (LOV) and recommends immediate and
permanent removal from service of any airplanes upon reaching the LOV, whether or not it is
operated under FAA jurisdiction. As such, Boeing no longer provides maintenance instructions for
airplanes that have accumulated flight cycles beyond the LOV. Airplanes in Group 1 (line numbers
1-291) have accumulated flight cycles beyond the LOV of the maintenance program. 14 CFR
121.1115 and 129.115 prohibit operation of an airplane beyond its LOV.
Group 2; Group 3, Configuration 1:
The actions required for each INSPECTION in Table 1 are identified as follows:
Group 2; Group 3, Configuration 1:
ActionTitle
ACTION 1: Inspect the flap track assembly for part number. As an alternative to the
inspection, a review of the maintenance records can be used if the part number of the
flap track assembly can be positively determined.
INSPECTION 1
ACTION 2: Do a detailed inspection of the flap track flanges and webs for any crack,
any nick, any corrosion pit, any galling, any piece broken off, and any stop-drill repair.
ACTION 3: Do a surface High Frequency Eddy Current (HFEC) inspection of the flap
track flanges and webs for any crack.
ACTION 4: Do a surface HFEC inspection and an ultrasonic inspection of the upper
flap track flange for any crack.
ACTION 5: Do a detailed inspection of the anti-fret strip and the tapered shim for any
damage and any corrosion.
ACTION 6: Do a detailed inspection of the flap track at the rear spar attachment for
any crack, any corrosion and any loose fastener.
ACTION 1: Do a detailed inspection of the anti-fret strip for presence or absence of
the anti-fret strip and for any damage and for material.
INSPECTION 2
ACTION 2: Do a detailed inspection of the tapered shim for presence or absence, any
damage, any corrosion, and for material, and measure the width of the tapered shim
normal to its aft edge.
ACTION 3: Do a detailed inspection of the flap track in the area of the rear spar attach-
ment mating surface for any corrosion.
ACTION 4: Do a detailed inspection of the outer circumferential surface of the bushing
for any corrosion.
ACTION 5: Do a surface HFEC inspection and an open hole HFEC inspection of the
flap track for any crack.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 25, 2017
737-57A1338 RB
37 of 161
REQUIREMENTS BULLETIN 737-57A1338
ALERTALERT

### Page 38

Group 2; Group 3, Configuration 1:
Table 1: Detailed Inspections and NDT Inspections of the Outboard Flap Tracks at Positions 1 and 8
Refer to the listed procedures in
SB 737-57A1338 Original Issue or
later approved revisions as an
accepted procedure:
Method of Compli-
ance
ActionCondition
PART 1: OPEN ACCESS-ACTION 1: Do IN-
SPECTION 1 on
each affected flap
track.
Airplanes with flap tracks
that have known mainte-
nance records and on which
an overhaul was done
PART 5: SEALANT REMOVAL
-FIGURE 1, FIGURE 2,
FIGURE 5, FIGURE 6,
FIGURE 7, FIGURE 8,
FIGURE 27, FIGURE
28, FIGURE 33, FIG-
URE 34
PART 6: SEALANT APPLICATION-
PART 2: CLOSE ACCESS
CMM 57-53-15-ACTION 2: Do an
overhaul of each
affected flap track.
(c)
PART 1: OPEN ACCESS-ACTION 1: Do IN-
SPECTION 1 on
each affected flap
track.
Airplanes with flap tracks
that have known mainte-
nance records and on which
no overhaul was done
PART 5: SEALANT REMOVAL
-FIGURE 1, FIGURE 2,
FIGURE 5, FIGURE 6,
FIGURE 7, FIGURE 8,
FIGURE 27, FIGURE
28, FIGURE 33, FIG-
URE 34
PART 6: SEALANT APPLICATION-
PART 2: CLOSE ACCESS
CMM 57-53-15-ACTION 2: Do an
overhaul of each
affected flap track.
(c)
PART 1: OPEN ACCESS-ACTION 1: Do IN-
SPECTION 1 on
each affected flap
track.
Airplanes with flap tracks
that have unknown mainte-
nance records
PART 5: SEALANT REMOVAL
-FIGURE 1, FIGURE 2,
FIGURE 5, FIGURE 6,
FIGURE 7, FIGURE 8,
FIGURE 27, FIGURE
28, FIGURE 33, FIG-
URE 34
PART 6: SEALANT APPLICATION-
PART 2: CLOSE ACCESS
CMM 57-53-15-ACTION 2: Do an
overhaul of each
affected flap track.
(c)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 25, 2017
737-57A1338 RB
38 of 161
REQUIREMENTS BULLETIN 737-57A1338
ALERTALERT

### Page 39

Group 2; Group 3, Configuration 1:
Table 1: Detailed Inspections and NDT Inspections of the Outboard Flap Tracks at Positions 1 and 8
Refer to the listed procedures in
SB 737-57A1338 Original Issue or
later approved revisions as an
accepted procedure:
Method of Compli-
ance
ActionCondition
737-100/200 AMM 27-51-151 or
737-300/400/500 AMM 27-51-49
-Remove the flap
track and install a
new or serviceable
flap track. (b)
CONDITION 101: FLAP
TRACK ASSEMBLY PART
NUMBER IS 65-46428-30
OR 65-46428-32 (a)
737-100/200 AMM 27-51-151 or
737-300/400/500 AMM 27-51-49
-Remove the flap
track and install a
new or serviceable
flap track. (b)
CONDITION 102: ANY
CRACK, ANY NICK, ANY
CORROSION PIT, ANY
GALLING, ANY PIECE
BROKEN OFF OR ANY
STOP-DRILL REPAIR
FOUND during INSPEC-
TION 1 (a)
PART 1: OPEN ACCESS-Repeat INSPEC-
TION 1.
CONDITION 103: NO
CRACK, NO NICK, NO
CORROSION PIT, NO
GALLING, NO PIECE
BROKEN OFF AND NO
STOP-DRILL REPAIR
FOUND during INSPEC-
TION 1 (a)
PART 5: SEALANT REMOVAL
-FIGURE 1, FIGURE 2,
FIGURE 5, FIGURE 6,
FIGURE 7, FIGURE 8,
FIGURE 27, FIGURE
28, FIGURE 33, FIG-
URE 34
PART 6: SEALANT APPLICATION-
PART 2: CLOSE ACCESS
PART 7: FLAP TRACK REAR SPAR
ATTACHMENT DISASSEMBLY
-ACTION 1: Do IN-
SPECTION 2 and
all applicable relat-
ed corrective ac-
tions.
CONDITION 104: ANY
DAMAGE OR ANY CORRO-
SION FOUND ON THE
ANTI-FRET STRIP OR ON
THE TAPERED SHIM; OR
ANY CORROSION OR
ANY LOOSE FASTENER
FOUND ON THE FLAP
TRACK AT THE REAR
SPAR ATTACHMENT dur-
ing INSPECTION 1 (a)
-FIGURE 45, FIGURE
46, FIGURE 47, FIG-
URE 48
737-100/200 AMM 27-51-151 or
737-300/400/500 AMM 27-51-49
-ACTION 2: Install
the repaired flap
track, or a new or
serviceable flap
track. (b)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 25, 2017
737-57A1338 RB
39 of 161
REQUIREMENTS BULLETIN 737-57A1338
ALERTALERT

### Page 40

Group 2; Group 3, Configuration 1:
Table 1: Detailed Inspections and NDT Inspections of the Outboard Flap Tracks at Positions 1 and 8
Refer to the listed procedures in
SB 737-57A1338 Original Issue or
later approved revisions as an
accepted procedure:
Method of Compli-
ance
ActionCondition
PART 1: OPEN ACCESS-Repeat INSPEC-
TION 1.
CONDITION 105: NO
DAMAGE AND NO CORRO-
SION FOUND ON THE
ANTI-FRET STRIP AND
ON THE TAPERED SHIM;
AND NO CORROSION
AND NO LOOSE FASTEN-
ER FOUND ON THE FLAP
TRACK AT THE REAR
SPAR ATTACHMENT dur-
ing INSPECTION 1 (a)
PART 5: SEALANT REMOVAL
-FIGURE 1, FIGURE 2,
FIGURE 5, FIGURE 6,
FIGURE 7, FIGURE 8,
FIGURE 27, FIGURE
28, FIGURE 33, FIG-
URE 34
PART 6: SEALANT APPLICATION
PART 2: CLOSE ACCESS
-
737-100/200 AMM 27-51-151 or
737-300/400/500 AMM 27-51-49
-ACTION 1: Re-
move the anti-fret
strip and install a
new anti-fret strip.
CONDITION 106: ANTI-
FRET STRIP IS MISSING
OR ANTI-FRET STRIP IS
MADE FROM PHENOLIC
MATERIAL OR ANY DAM-
AGE FOUND ON THE AN-
TI-FRET STRIP during IN-
SPECTION 2 (a)
PART 1: OPEN ACCESS
PART 5: SEALANT REMOVAL
-ACTION 2: Repeat
INSPECTION 1.
-FIGURE 1, FIGURE 2,
FIGURE 5, FIGURE 6,
FIGURE 7, FIGURE 8,
FIGURE 27, FIGURE
28, FIGURE 33, FIG-
URE 34
PART 6: SEALANT APPLICATION-
PART 2: CLOSE ACCESS
PART 1: OPEN ACCESS-Repeat INSPEC-
TION 1.
CONDITION 107: ANTI-
FRET STRIP IS NOT
MISSING AND ANTI-FRET
STRIP IS NOT MADE
FROM PHENOLIC MATERI-
AL AND NO DAMAGE
FOUND ON THE ANTI-
FRET STRIP during IN-
SPECTION 2 (a)
PART 5: SEALANT REMOVAL
-FIGURE 1, FIGURE 2,
FIGURE 5, FIGURE 6,
FIGURE 7, FIGURE 8,
FIGURE 27, FIGURE
28, FIGURE 33, FIG-
URE 34
PART 6: SEALANT APPLICATION-
PART 2: CLOSE ACCESS
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 25, 2017
737-57A1338 RB
40 of 161
REQUIREMENTS BULLETIN 737-57A1338
ALERTALERT

### Page 41

Group 2; Group 3, Configuration 1:
Table 1: Detailed Inspections and NDT Inspections of the Outboard Flap Tracks at Positions 1 and 8
Refer to the listed procedures in
SB 737-57A1338 Original Issue or
later approved revisions as an
accepted procedure:
Method of Compli-
ance
ActionCondition
737-100/200 AMM 27-51-151 or
737-300/400/500 AMM 27-51-49
-ACTION 1: Re-
move the tapered
shim and install a
new tapered shim.
CONDITION 108: TA-
PERED SHIM IS MISSING
OR TAPERED SHIM IS
MADE FROM LAMINATED
MATERIAL OR WIDTH OF
TAPERED SHIM IS LESS
THAN 1.70 INCHES OR
ANY DAMAGE OR ANY
CORROSION FOUND ON
THE TAPERED SHIM dur-
ing INSPECTION 2 (a)
PART 1: OPEN ACCESS
PART 5: SEALANT REMOVAL
-ACTION 2: Repeat
INSPECTION 1.
-FIGURE 1, FIGURE 2,
FIGURE 5, FIGURE 6,
FIGURE 7, FIGURE 8,
FIGURE 27, FIGURE
28, FIGURE 33, FIG-
URE 34
PART 6: SEALANT APPLICATION-
PART 2: CLOSE ACCESS
PART 1: OPEN ACCESS-Repeat INSPEC-
TION 1.
CONDITION 109: TA-
PERED SHIM IS NOT
MISSING AND TAPERED
SHIM IS NOT MADE FROM
LAMINATED MATERIAL
AND WIDTH OF TAPERED
SHIM IS 1.70 INCHES OR
MORE AND NO DAMAGE
AND NO CORROSION
FOUND ON THE TA-
PERED SHIM during IN-
SPECTION 2 (a)
PART 5: SEALANT REMOVAL
-FIGURE 1, FIGURE 2,
FIGURE 5, FIGURE 6,
FIGURE 7, FIGURE 8,
FIGURE 27, FIGURE
28, FIGURE 33, FIG-
URE 34
PART 6: SEALANT APPLICATION
PART 2: CLOSE ACCESS
-
CMM 57-53-15-ACTION 1: Repair
the flap track.
CONDITION 110: ANY
CORROSION OR ANY
CRACK FOUND ON THE
FLAP TRACK THAT IS IN
THE REPAIR LIMITS OF
CMM 57-53-15 during IN-
SPECTION 2 (a)(c)
(c)
PART 1: OPEN ACCESS
PART 5: SEALANT REMOVAL
-ACTION 2: Repeat
INSPECTION 1.
-FIGURE 1, FIGURE 2,
FIGURE 5, FIGURE 6,
FIGURE 7, FIGURE 8,
FIGURE 27, FIGURE
28, FIGURE 33, FIG-
URE 34
PART 6: SEALANT APPLICATION-
PART 2: CLOSE ACCESS
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 25, 2017
737-57A1338 RB
41 of 161
REQUIREMENTS BULLETIN 737-57A1338
ALERTALERT

### Page 42

Group 2; Group 3, Configuration 1:
Table 1: Detailed Inspections and NDT Inspections of the Outboard Flap Tracks at Positions 1 and 8
Refer to the listed procedures in
SB 737-57A1338 Original Issue or
later approved revisions as an
accepted procedure:
Method of Compli-
ance
ActionCondition
737-100/200 AMM 27-51-151 or
737-300/400/500 AMM 27-51-49
-Remove the flap
track and install a
new or serviceable
flap track. (b)
CONDITION 111: ANY
CORROSION OR ANY
CRACK FOUND ON THE
FLAP TRACK THAT IS
LARGER THAN THE RE-
PAIR LIMITS OF CMM 57-
53-15 during INSPECTION
2 (a)(c)
PART 1: OPEN ACCESS-Repeat INSPEC-
TION 1.
CONDITION 112: NO
CORROSION AND NO
CRACK FOUND ON THE
FLAP TRACK during IN-
SPECTION 2 (a)
PART 5: SEALANT REMOVAL
-FIGURE 1, FIGURE 2,
FIGURE 5, FIGURE 6,
FIGURE 7, FIGURE 8,
FIGURE 27, FIGURE
28, FIGURE 33, FIG-
URE 34
PART 6: SEALANT APPLICATION-
PART 2: CLOSE ACCESS
CMM 57-53-15, and 737-100/200
AMM 27-51-151 or 737-300/400/500
AMM 27-51-49
-ACTION 1: Re-
move the bushing
and install a new or
serviceable bush-
ing.
CONDITION 113: ANY
CORROSION FOUND ON
THE BUSHING during IN-
SPECTION 2 (a) (c)
PART 1: OPEN ACCESS-ACTION 2: Repeat
INSPECTION 1. PART 5: SEALANT REMOVAL
-FIGURE 1, FIGURE 2,
FIGURE 5, FIGURE 6,
FIGURE 7, FIGURE 8,
FIGURE 27, FIGURE
28, FIGURE 33, FIG-
URE 34
PART 6: SEALANT APPLICATION-
PART 2: CLOSE ACCESS
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 25, 2017
737-57A1338 RB
42 of 161
REQUIREMENTS BULLETIN 737-57A1338
ALERTALERT

### Page 43

Group 2; Group 3, Configuration 1:
Table 1: Detailed Inspections and NDT Inspections of the Outboard Flap Tracks at Positions 1 and 8
Refer to the listed procedures in
SB 737-57A1338 Original Issue or
later approved revisions as an
accepted procedure:
Method of Compli-
ance
ActionCondition
PART 1: OPEN ACCESS-Repeat INSPEC-
TION 1.
CONDITION 114: NO
CORROSION FOUND ON
THE BUSHING during IN-
SPECTION 2 (a)
PART 5: SEALANT REMOVAL
-FIGURE 1, FIGURE 2,
FIGURE 5, FIGURE 6,
FIGURE 7, FIGURE 8,
FIGURE 27, FIGURE
28, FIGURE 33, FIG-
URE 34
PART 6: SEALANT APPLICATION-
PART 2: CLOSE ACCESS
737-100/200 AMM 27-51-151 or
737-300/400/500 AMM 27-51-49
-Remove the flap
track and install a
new or serviceable
flap track. (b)
CONDITION 115: FLAP
TRACK CANNOT BE PUT
BACK TO A SERVICE-
ABLE CONDITION during
overhaul (a)
CMM 57-53-15-Repeat the over-
haul of the flap
track.
CONDITION 116: FLAP
TRACK FOUND SERVICE-
ABLE OR PUT BACK TO A
SERVICEABLE CONDI-
TION during overhaul (a)
(c)
(a) More than one CONDITION can be applicable on each flap track.
(b) The replacement flap track, whether new or serviceable, must be in compliance with the initial inspection
requirements and compliance times based on the applicable flap track condition. Inspections and overhauls
previously accomplished in accordance with Requirements Bulletin 737-57A1338 RB can be used to sat-
isfy these requirements, so long as the track continues to comply with repeat intervals specified in the table.
For Group 3 airplanes, replacement of the flap track could result in a change in Configuration. Comply
with all requirements specified in the table for the Configuration of the flap track installed.
(c) CMM 57-53-15, Revision 44, dated March 1, 2016 and Temporary Revision 57-3003, dated August 18,
2017, or later revisions.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 25, 2017
737-57A1338 RB
43 of 161
REQUIREMENTS BULLETIN 737-57A1338
ALERTALERT

### Page 44

Group 3, Configuration 2:
The actions required for each INSPECTION in Table 2 are identified as follows:
Group 3, Configuration 2:
ActionTitle
ACTION 1: Do a detailed inspection of the flap track flanges and webs for any crack,
any nick, any corrosion pit, any galling, any piece broken off, and any stop-drill repair.
INSPECTION 3
ACTION 2: Do a surface High Frequency Eddy Current (HFEC) inspection of the flap
track flanges and webs, and an open hole HFEC inspection of the flap track webs for
any crack.
ACTION 3: Do a surface HFEC inspection and an ultrasonic inspection of the upper
flap track flange for any crack.
ACTION 4: Do a detailed inspection of the anti-fret strip and the tapered shim for any
damage and any corrosion.
ACTION 5: Do a detailed inspection of the flap track at the rear spar attachment for
any crack, any corrosion and any loose fastener.
ACTION 1: Do a detailed inspection of the anti-fret strip for presence or absence of
the anti-fret strip and for any damage and for material.
INSPECTION 4
ACTION 2: Do a detailed inspection of the tapered shim for presence or absence, any
damage, any corrosion, and for material, and measure the width of the tapered shim
normal to its aft edge.
ACTION 3: Do a detailed inspection of the flap track in the area of the rear spar attach-
ment mating surface for any corrosion.
ACTION 4: Do a detailed inspection of the outer circumferential surface of the bushing
for any corrosion.
ACTION 5: Do a surface HFEC inspection and an open hole HFEC inspection of the
flap track for any crack.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 25, 2017
737-57A1338 RB
44 of 161
REQUIREMENTS BULLETIN 737-57A1338
ALERTALERT

### Page 45

Group 3, Configuration 2:
Table 2: Detailed Inspections and NDT Inspections of the Outboard Flap Tracks at Positions 1 and 8
Refer to the listed procedures in
SB 737-57A1338 Original Issue or
later approved revisions as an
accepted procedure:
Method of Compli-
ance
ActionCondition
PART 1: OPEN ACCESS-ACTION 1: Do IN-
SPECTION 3 on
each affected flap
track.
Airplanes with flap tracks
that have known mainte-
nance records and on which
an overhaul was done
PART 3: FASTENER REMOVAL
PART 5: SEALANT REMOVAL
-FIGURE 1, FIGURE 2,
FIGURE 11, FIGURE
12, FIGURE 27, FIG-
URE 28, FIGURE 33,
FIGURE 34
PART 6: SEALANT APPLICATION-
PART 4: FASTENER INSTALLA-
TION
PART 2: CLOSE ACCESS
CMM 57-53-15-ACTION 2: Do an
overhaul of each
affected flap track.
(c)
PART 1: OPEN ACCESS-ACTION 1: Do IN-
SPECTION 3 on
each affected flap
track.
Airplanes with flap tracks
that have known mainte-
nance records and on which
no overhaul was done
PART 3: FASTENER REMOVAL
PART 5: SEALANT REMOVAL
-FIGURE 1, FIGURE 2,
FIGURE 11, FIGURE
12, FIGURE 27, FIG-
URE 28, FIGURE 33,
FIGURE 34
PART 6: SEALANT APPLICATION-
PART 4: FASTENER INSTALLA-
TION
PART 2: CLOSE ACCESS
CMM 57-53-15-ACTION 2: Do an
overhaul of each
affected flap track.
(c)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 25, 2017
737-57A1338 RB
45 of 161
REQUIREMENTS BULLETIN 737-57A1338
ALERTALERT

### Page 46

Group 3, Configuration 2:
Table 2: Detailed Inspections and NDT Inspections of the Outboard Flap Tracks at Positions 1 and 8
Refer to the listed procedures in
SB 737-57A1338 Original Issue or
later approved revisions as an
accepted procedure:
Method of Compli-
ance
ActionCondition
PART 1: OPEN ACCESS-ACTION 1: Do IN-
SPECTION 3 on
each affected flap
track.
Airplanes with flap tracks
that have unknown mainte-
nance records
PART 3: FASTENER REMOVAL
PART 5: SEALANT REMOVAL
-FIGURE 1, FIGURE 2,
FIGURE 11, FIGURE
12, FIGURE 27, FIG-
URE 28, FIGURE 33,
FIGURE 34
PART 6: SEALANT APPLICATION-
PART 4: FASTENER INSTALLA-
TION
PART 2: CLOSE ACCESS
CMM 57-53-15-ACTION 2: Do an
overhaul of each
affected flap track.
(c)
737-300/400/500 AMM 27-51-49-Remove the flap
track and install a
new or serviceable
flap track. (b)
CONDITION 201: ANY
CRACK, ANY NICK, ANY
CORROSION PIT, ANY
GALLING, ANY PIECE
BROKEN OFF OR ANY
STOP-DRILL REPAIR
FOUND during INSPEC-
TION 3 (a)
PART 1: OPEN ACCESS-Repeat INSPEC-
TION 3.
CONDITION 202: NO
CRACK, NO NICK, NO
CORROSION PIT, NO
GALLING, NO PIECE
BROKEN OFF AND NO
STOP-DRILL REPAIR
FOUND during INSPEC-
TION 3 (a)
PART 3: FASTENER REMOVAL
PART 5: SEALANT REMOVAL
-FIGURE 1, FIGURE 2,
FIGURE 11, FIGURE
12, FIGURE 27, FIG-
URE 28, FIGURE 33,
FIGURE 34
PART 6: SEALANT APPLICATION-
PART 4: FASTENER INSTALLA-
TION
PART 2: CLOSE ACCESS
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 25, 2017
737-57A1338 RB
46 of 161
REQUIREMENTS BULLETIN 737-57A1338
ALERTALERT

### Page 47

Group 3, Configuration 2:
Table 2: Detailed Inspections and NDT Inspections of the Outboard Flap Tracks at Positions 1 and 8
Refer to the listed procedures in
SB 737-57A1338 Original Issue or
later approved revisions as an
accepted procedure:
Method of Compli-
ance
ActionCondition
PART 7: FLAP TRACK REAR SPAR
ATTACHMENT DISASSEMBLY
-ACTION 1: Do IN-
SPECTION 4 and
all applicable relat-
ed corrective ac-
tions.
CONDITION 203: ANY
DAMAGE OR ANY CORRO-
SION FOUND ON THE
ANTI-FRET STRIP OR ON
THE TAPERED SHIM; OR
ANY CORROSION OR
ANY LOOSE FASTENER
FOUND ON THE FLAP
TRACK AT THE REAR
SPAR ATTACHMENT dur-
ing INSPECTION 3 (a)
-FIGURE 45, FIGURE
46, FIGURE 47, FIG-
URE 48
737-300/400/500 AMM 27-51-49-ACTION 2: Install
the repaired flap
track, or a new or
serviceable flap
track. (b)
PART 1: OPEN ACCESS-Repeat INSPEC-
TION 3.
CONDITION 204: NO
DAMAGE AND NO CORRO-
SION FOUND ON THE
ANTI-FRET STRIP AND
ON THE TAPERED SHIM;
AND NO CORROSION
AND NO LOOSE FASTEN-
ER FOUND ON THE FLAP
TRACK AT THE REAR
SPAR ATTACHMENT dur-
ing INSPECTION 3 (a)
PART 3: FASTENER REMOVAL
PART 5: SEALANT REMOVAL
-FIGURE 1, FIGURE 2,
FIGURE 11, FIGURE
12, FIGURE 27, FIG-
URE 28, FIGURE 33,
FIGURE 34
PART 6: SEALANT APPLICATION
PART 4: FASTENER INSTALLA-
TION
-
PART 2: CLOSE ACCESS
737-300/400/500 AMM 27-51-49-ACTION 1: Re-
move the anti-fret
strip and install a
new anti-fret strip.
CONDITION 205: ANTI-
FRET STRIP IS MISSING
OR ANTI-FRET STRIP IS
MADE FROM PHENOLIC
MATERIAL OR ANY DAM-
AGE FOUND ON THE AN-
TI-FRET STRIP during IN-
SPECTION 4 (a)
PART 1: OPEN ACCESS
PART 3: FASTENER REMOVAL
PART 5: SEALANT REMOVAL
-ACTION 2: Repeat
INSPECTION 3.
-FIGURE 1, FIGURE 2,
FIGURE 11, FIGURE
12, FIGURE 27, FIG-
URE 28, FIGURE 33,
FIGURE 34
PART 6: SEALANT APPLICATION-
PART 4: FASTENER INSTALLA-
TION
PART 2: CLOSE ACCESS
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 25, 2017
737-57A1338 RB
47 of 161
REQUIREMENTS BULLETIN 737-57A1338
ALERTALERT

### Page 48

Group 3, Configuration 2:
Table 2: Detailed Inspections and NDT Inspections of the Outboard Flap Tracks at Positions 1 and 8
Refer to the listed procedures in
SB 737-57A1338 Original Issue or
later approved revisions as an
accepted procedure:
Method of Compli-
ance
ActionCondition
PART 1: OPEN ACCESS-Repeat INSPEC-
TION 3.
CONDITION 206: ANTI-
FRET STRIP IS NOT
MISSING AND ANTI-FRET
STRIP IS NOT MADE
FROM PHENOLIC MATERI-
AL AND NO DAMAGE
FOUND ON THE ANTI-
FRET STRIP during IN-
SPECTION 4 (a)
PART 3: FASTENER REMOVAL
PART 5: SEALANT REMOVAL
-FIGURE 1, FIGURE 2,
FIGURE 11, FIGURE
12, FIGURE 27, FIG-
URE 28, FIGURE 33,
FIGURE 34
PART 6: SEALANT APPLICATION-
PART 4: FASTENER INSTALLA-
TION
PART 2: CLOSE ACCESS
737-300/400/500 AMM 27-51-49-ACTION 1: Re-
move the tapered
shim and install a
new tapered shim.
CONDITION 207: TA-
PERED SHIM IS MISSING
OR TAPERED SHIM IS
MADE FROM LAMINATED
MATERIAL OR WIDTH OF
TAPERED SHIM IS LESS
THAN 1.70 INCHES OR
ANY DAMAGE OR ANY
CORROSION FOUND ON
THE TAPERED SHIM dur-
ing INSPECTION 4 (a)
PART 1: OPEN ACCESS
PART 3: FASTENER REMOVAL
PART 5: SEALANT REMOVAL
-ACTION 2: Repeat
INSPECTION 3.
-FIGURE 1, FIGURE 2,
FIGURE 11, FIGURE
12, FIGURE 27, FIG-
URE 28, FIGURE 33,
FIGURE 34
PART 6: SEALANT APPLICATION-
PART 4: FASTENER INSTALLA-
TION
PART 2: CLOSE ACCESS
PART 1: OPEN ACCESS-Repeat INSPEC-
TION 3.
CONDITION 208: TA-
PERED SHIM IS NOT
MISSING AND TAPERED
SHIM IS NOT MADE FROM
LAMINATED MATERIAL
AND WIDTH OF TAPERED
SHIM IS 1.70 INCHES OR
MORE AND NO DAMAGE
AND NO CORROSION
FOUND ON THE TA-
PERED SHIM during IN-
SPECTION 4 (a)
PART 3: FASTENER REMOVAL
PART 5: SEALANT REMOVAL
-FIGURE 1, FIGURE 2,
FIGURE 11, FIGURE
12, FIGURE 27, FIG-
URE 28, FIGURE 33,
FIGURE 34
PART 6: SEALANT APPLICATION
PART 4: FASTENER INSTALLA-
TION
-
PART 2: CLOSE ACCESS
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 25, 2017
737-57A1338 RB
48 of 161
REQUIREMENTS BULLETIN 737-57A1338
ALERTALERT

### Page 49

Group 3, Configuration 2:
Table 2: Detailed Inspections and NDT Inspections of the Outboard Flap Tracks at Positions 1 and 8
Refer to the listed procedures in
SB 737-57A1338 Original Issue or
later approved revisions as an
accepted procedure:
Method of Compli-
ance
ActionCondition
CMM 57-53-15-ACTION 1: Repair
the flap track.
CONDITION 209: ANY
CORROSION OR ANY
CRACK FOUND ON THE
FLAP TRACK THAT IS IN
THE REPAIR LIMITS OF
CMM 57-53-15 during IN-
SPECTION 4 (a)(c)
(c)
PART 1: OPEN ACCESS
PART 3: FASTENER REMOVAL
PART 5: SEALANT REMOVAL
-ACTION 2: Repeat
INSPECTION 3.
-FIGURE 1, FIGURE 2,
FIGURE 11, FIGURE
12, FIGURE 27, FIG-
URE 28, FIGURE 33,
FIGURE 34
PART 6: SEALANT APPLICATION-
PART 4: FASTENER INSTALLA-
TION
PART 2: CLOSE ACCESS
737-300/400/500 AMM 27-51-49-Remove the flap
track and install a
new or serviceable
flap track. (b)
CONDITION 210: ANY
CORROSION OR ANY
CRACK FOUND ON THE
FLAP TRACK THAT IS
LARGER THAN THE RE-
PAIR LIMITS OF CMM 57-
53-15 during INSPECTION
4 (a)(c)
PART 1: OPEN ACCESS-Repeat INSPEC-
TION 3.
CONDITION 211: NO
CORROSION AND NO
CRACK FOUND ON THE
FLAP TRACK during IN-
SPECTION 4 (a)
PART 3: FASTENER REMOVAL
PART 5: SEALANT REMOVAL
-FIGURE 1, FIGURE 2,
FIGURE 11, FIGURE
12, FIGURE 27, FIG-
URE 28, FIGURE 33,
FIGURE 34
PART 6: SEALANT APPLICATION-
PART 4: FASTENER INSTALLA-
TION
PART 2: CLOSE ACCESS
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 25, 2017
737-57A1338 RB
49 of 161
REQUIREMENTS BULLETIN 737-57A1338
ALERTALERT

### Page 50

Group 3, Configuration 2:
Table 2: Detailed Inspections and NDT Inspections of the Outboard Flap Tracks at Positions 1 and 8
Refer to the listed procedures in
SB 737-57A1338 Original Issue or
later approved revisions as an
accepted procedure:
Method of Compli-
ance
ActionCondition
CMM 57-53-15 and 737-
300/400/500 AMM 27-51-49
-ACTION 1: Re-
move the bushing
and install a new or
serviceable bush-
ing.
CONDITION 212: ANY
CORROSION FOUND ON
THE BUSHING during IN-
SPECTION 4 (a)
(c)
PART 1: OPEN ACCESS-ACTION 2: Repeat
INSPECTION 3. PART 3: FASTENER REMOVAL
PART 5: SEALANT REMOVAL
-FIGURE 1, FIGURE 2,
FIGURE 11, FIGURE
12, FIGURE 27, FIG-
URE 28, FIGURE 33,
FIGURE 34
PART 6: SEALANT APPLICATION-
PART 4: FASTENER INSTALLA-
TION
PART 2: CLOSE ACCESS
PART 1: OPEN ACCESS-Repeat INSPEC-
TION 3.
CONDITION 213: NO
CORROSION FOUND ON
THE BUSHING during IN-
SPECTION 4 (a)
PART 3: FASTENER REMOVAL
PART 5: SEALANT REMOVAL
-FIGURE 1, FIGURE 2,
FIGURE 11, FIGURE
12, FIGURE 27, FIG-
URE 28, FIGURE 33,
FIGURE 34
PART 6: SEALANT APPLICATION-
PART 4: FASTENER INSTALLA-
TION
PART 2: CLOSE ACCESS
737-300/400/500 AMM 27-51-49-Remove the flap
track and install a
new or serviceable
flap track. (b)
CONDITION 214: FLAP
TRACK CANNOT BE PUT
BACK TO A SERVICE-
ABLE CONDITION during
overhaul (a)
CMM 57-53-15-Repeat the over-
haul of the flap
track.
CONDITION 215: FLAP
TRACK FOUND SERVICE-
ABLE OR PUT BACK TO A
SERVICEABLE CONDI-
TION during overhaul (a)
(c)
(a) More than one CONDITION can be applicable on each flap track.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 25, 2017
737-57A1338 RB
50 of 161
REQUIREMENTS BULLETIN 737-57A1338
ALERTALERT

### Page 51

Group 3, Configuration 2:
Table 2: Detailed Inspections and NDT Inspections of the Outboard Flap Tracks at Positions 1 and 8
Refer to the listed procedures in
SB 737-57A1338 Original Issue or
later approved revisions as an
accepted procedure:
Method of Compli-
ance
ActionCondition
(b) The replacement flap track, whether new or serviceable, must be in compliance with the initial inspection
requirements and compliance times based on the applicable flap track condition. Inspections and overhauls
previously accomplished in accordance with Requirements Bulletin 737-57A1338 RB can be used to sat-
isfy these requirements, so long as the track continues to comply with repeat intervals specified in the table.
For Group 3 airplanes, replacement of the flap track could result in a change in Configuration. Comply
with all requirements specified in the table for the Configuration of the flap track installed.
(c) CMM 57-53-15, Revision 44, dated March 1, 2016 and Temporary Revision 57-3003, dated August 18,
2017, or later revisions.
Group 2; Group 3, Configuration 1:
The actions required for each INSPECTION in Table 3 are identified as follows:
Group 2; Group 3, Configuration 1:
ActionTitle
Do a surface HFEC inspection of the flap track flanges and webs for any crack.INSPECTION 5
ACTION 1: Inspect the flap track assembly for part number. As an alternative to the
inspection, a review of the maintenance records can be used if the part number of the
flap track assembly can be positively determined.
INSPECTION 6 (a)
ACTION 2: Do a detailed inspection of the flap track flanges and webs for any crack,
any nick, any corrosion pit, any galling, any piece broken off, and any stop-drill repair.
ACTION 3: Do a surface HFEC inspection of the flap track flanges and webs for any
crack.
ACTION 4: Do a surface HFEC inspection and an ultrasonic inspection of the upper
flap track flange for any crack.
ACTION 5: Do a detailed inspection of the anti-fret strip and the tapered shim for any
damage and any corrosion.
ACTION 6: Do a detailed inspection of the flap track at the rear spar attachment for
any crack, any corrosion and any loose fastener.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 25, 2017
737-57A1338 RB
51 of 161
REQUIREMENTS BULLETIN 737-57A1338
ALERTALERT

### Page 52

Group 2; Group 3, Configuration 1:
ActionTitle
ACTION 1: Do a detailed inspection of the anti-fret strip for presence or absence of
the anti-fret strip and for any damage and for material.
INSPECTION 7 (a)
ACTION 2: Do a detailed inspection of the tapered shim for presence or absence, any
damage, any corrosion, and for material, and measure the width of the tapered shim
normal to its aft edge.
ACTION 3: Do a detailed inspection of the flap track in the area of the rear spar attach-
ment mating surface for any corrosion.
ACTION 4: Do a detailed inspection of the outer circumferential surface of the bushing
for any corrosion.
ACTION 5: Do a surface HFEC inspection and an open hole HFEC inspection of the
flap track for any crack.
(a) This INSPECTION is related to SB 737-57A1271.
Group 2; Group 3, Configuration 1:
Table 3: Detailed Inspections and NDT Inspections of the Outboard Flap Tracks at Positions 2 and 7
Refer to the listed procedures in
SB 737-57A1338 Original Issue or
later approved revisions as an
accepted procedure:
Method of Compli-
ance
ActionCondition
PART 1: OPEN ACCESS-ACTION 1: Do IN-
SPECTION 5 on
each affected flap
track.
Airplanes with flap tracks on
which an overhaul was
done -FIGURE 15, FIGURE16, FIGURE 17, FIG-
URE 18
PART 2: CLOSE ACCESS-
PART 1: OPEN ACCESS-ACTION 2: Do IN-
SPECTION 6 on
each affected flap
track.
PART 5: SEALANT REMOVAL
-FIGURE 3, FIGURE 4,
FIGURE 25, FIGURE
26, FIGURE 29, FIG-
URE 30, FIGURE 39,
FIGURE 40
PART 6: SEALANT APPLICATION-
PART 2: CLOSE ACCESS
CMM 57-53-15-ACTION 3: Do an
overhaul of each
affected flap track.
(c)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 25, 2017
737-57A1338 RB
52 of 161
REQUIREMENTS BULLETIN 737-57A1338
ALERTALERT

### Page 53

Group 2; Group 3, Configuration 1:
Table 3: Detailed Inspections and NDT Inspections of the Outboard Flap Tracks at Positions 2 and 7
Refer to the listed procedures in
SB 737-57A1338 Original Issue or
later approved revisions as an
accepted procedure:
Method of Compli-
ance
ActionCondition
PART 1: OPEN ACCESS-ACTION 1: Do IN-
SPECTION 5 on
each affected flap
track.
Airplanes with flap tracks on
which no overhaul was
done and no inspection was
done in accordance with SB
737-57A1271
-FIGURE 15, FIGURE
16, FIGURE 17, FIG-
URE 18
PART 2: CLOSE ACCESS-
PART 1: OPEN ACCESS-ACTION 2: Do IN-
SPECTION 6 on
each affected flap
track.
PART 5: SEALANT REMOVAL
-FIGURE 3, FIGURE 4,
FIGURE 25, FIGURE
26, FIGURE 29, FIG-
URE 30, FIGURE 39,
FIGURE 40
PART 6: SEALANT APPLICATION-
PART 2: CLOSE ACCESS
CMM 57-53-15-ACTION 3: Do an
overhaul of each
affected flap track.
(c)
PART 1: OPEN ACCESS-ACTION 1: Do IN-
SPECTION 5 on
each affected flap
track.
Airplanes with flap tracks on
which no overhaul was
done, and an inspection
was done in accordance
with SB 737-57A1271
-FIGURE 15, FIGURE
16, FIGURE 17, FIG-
URE 18
PART 2: CLOSE ACCESS-
PART 1: OPEN ACCESS-ACTION 2: Do IN-
SPECTION 6 on
each affected flap
track.
PART 5: SEALANT REMOVAL
-FIGURE 3, FIGURE 4,
FIGURE 25, FIGURE
26, FIGURE 29, FIG-
URE 30, FIGURE 39,
FIGURE 40
PART 6: SEALANT APPLICATION-
PART 2: CLOSE ACCESS
CMM 57-53-15-ACTION 3: Do an
overhaul of each
affected flap track.
(c)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 25, 2017
737-57A1338 RB
53 of 161
REQUIREMENTS BULLETIN 737-57A1338
ALERTALERT

### Page 54

Group 2; Group 3, Configuration 1:
Table 3: Detailed Inspections and NDT Inspections of the Outboard Flap Tracks at Positions 2 and 7
Refer to the listed procedures in
SB 737-57A1338 Original Issue or
later approved revisions as an
accepted procedure:
Method of Compli-
ance
ActionCondition
737-100/200 AMM 27-51-151 or
737-300/400/500 AMM 27-51-49
-Remove the flap
track and install a
new or serviceable
flap track. (b)
CONDITION 301: FLAP
TRACK ASSEMBLY PART
NUMBER IS 65-46428-31
OR 65-46428-33 (a)
737-100/200 AMM 27-51-151 or
737-300/400/500 AMM 27-51-49
-Remove the flap
track and install a
new or serviceable
flap track. (b)
CONDITION 302: ANY
CRACK, ANY NICK, ANY
CORROSION PIT, ANY
GALLING, ANY PIECE
BROKEN OFF OR ANY
STOP-DRILL REPAIR
FOUND during INSPEC-
TION 5 or INSPECTION 6
(a)
PART 1: OPEN ACCESS-Repeat INSPEC-
TION 5 and IN-
SPECTION 6.
CONDITION 303: NO
CRACK, NO NICK, NO
CORROSION PIT, NO
GALLING, NO PIECE
BROKEN OFF AND NO
STOP-DRILL REPAIR
FOUND during INSPEC-
TION 5 or INSPECTION 6
(a)
PART 5: SEALANT REMOVAL
-FIGURE 3, FIGURE 4,
FIGURE 15, FIGURE
16, FIGURE 17, FIG-
URE 18, FIGURE 25,
FIGURE 26, FIGURE
29, FIGURE 30, FIG-
URE 39, FIGURE 40
PART 6: SEALANT APPLICATION-
PART 2: CLOSE ACCESS
PART 7: FLAP TRACK REAR SPAR
ATTACHMENT DISASSEMBLY
-ACTION 1: Do IN-
SPECTION 7 and
all applicable relat-
ed corrective ac-
tions.
CONDITION 304: ANY
DAMAGE OR ANY CORRO-
SION FOUND ON THE
ANTI-FRET STRIP OR ON
THE TAPERED SHIM; OR
ANY CORROSION OR
ANY LOOSE FASTENER
FOUND ON THE FLAP
TRACK AT THE REAR
SPAR ATTACHMENT dur-
ing INSPECTION 6 (a)
-FIGURE 51, FIGURE
52, FIGURE 53, FIG-
URE 54
737-100/200 AMM 27-51-151 or
737-300/400/500 AMM 27-51-49
-ACTION 2: Install
the repaired flap
track, or a new or
serviceable flap
track. (b)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 25, 2017
737-57A1338 RB
54 of 161
REQUIREMENTS BULLETIN 737-57A1338
ALERTALERT

### Page 55

Group 2; Group 3, Configuration 1:
Table 3: Detailed Inspections and NDT Inspections of the Outboard Flap Tracks at Positions 2 and 7
Refer to the listed procedures in
SB 737-57A1338 Original Issue or
later approved revisions as an
accepted procedure:
Method of Compli-
ance
ActionCondition
PART 1: OPEN ACCESS-Repeat INSPEC-
TION 5 and IN-
SPECTION 6.
CONDITION 305: NO
DAMAGE AND NO CORRO-
SION FOUND ON THE
ANTI-FRET STRIP AND
ON THE TAPERED SHIM;
AND NO CORROSION
AND NO LOOSE FASTEN-
ER FOUND ON THE FLAP
TRACK AT THE REAR
SPAR ATTACHMENT dur-
ing INSPECTION 6 (a)
PART 5: SEALANT REMOVAL
-FIGURE 3, FIGURE 4,
FIGURE 15, FIGURE
16, FIGURE 17, FIG-
URE 18, FIGURE 25,
FIGURE 26, FIGURE
29, FIGURE 30, FIG-
URE 39, FIGURE 40
PART 6: SEALANT APPLICATION-
PART 2: CLOSE ACCESS
737-100/200 AMM 27-51-151 or
737-300/400/500 AMM 27-51-49
-ACTION 1: Re-
move the anti-fret
strip and install a
new anti-fret strip.
CONDITION 306: ANTI-
FRET STRIP IS MISSING
OR ANTI-FRET STRIP IS
MADE FROM PHENOLIC
MATERIAL OR ANY DAM-
AGE FOUND ON THE AN-
TI-FRET STRIP during IN-
SPECTION 7 (a)
PART 1: OPEN ACCESS
PART 5: SEALANT REMOVAL
-ACTION 2: Repeat
INSPECTION 5
and INSPECTION
6. -FIGURE 3, FIGURE 4,FIGURE 15, FIGURE
16, FIGURE 17, FIG-
URE 18, FIGURE 25,
FIGURE 26, FIGURE
29, FIGURE 30, FIG-
URE 39, FIGURE 40
PART 6: SEALANT APPLICATION-
PART 2: CLOSE ACCESS
PART 1: OPEN ACCESS-Repeat INSPEC-
TION 5 and IN-
SPECTION 6.
CONDITION 307: ANTI-
FRET STRIP IS NOT
MISSING AND ANTI-FRET
STRIP IS NOT MADE
FROM PHENOLIC MATERI-
AL AND NO DAMAGE
FOUND ON THE ANTI-
FRET STRIP during IN-
SPECTION 7 (a)
PART 5: SEALANT REMOVAL
-FIGURE 3, FIGURE 4,
FIGURE 15, FIGURE
16, FIGURE 17, FIG-
URE 18, FIGURE 25,
FIGURE 26, FIGURE
29, FIGURE 30, FIG-
URE 39, FIGURE 40
PART 6: SEALANT APPLICATION-
PART 2: CLOSE ACCESS
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 25, 2017
737-57A1338 RB
55 of 161
REQUIREMENTS BULLETIN 737-57A1338
ALERTALERT

### Page 56

Group 2; Group 3, Configuration 1:
Table 3: Detailed Inspections and NDT Inspections of the Outboard Flap Tracks at Positions 2 and 7
Refer to the listed procedures in
SB 737-57A1338 Original Issue or
later approved revisions as an
accepted procedure:
Method of Compli-
ance
ActionCondition
737-100/200 AMM 27-51-151 or
737-300/400/500 AMM 27-51-49
-ACTION 1: Re-
move the tapered
shim and install a
new tapered shim.
CONDITION 308: TA-
PERED SHIM IS MISSING
OR TAPERED SHIM IS
MADE FROM LAMINATED
MATERIAL OR WIDTH OF
TAPERED SHIM IS LESS
THAN 1.70 INCHES OR
ANY DAMAGE OR ANY
CORROSION FOUND ON
THE TAPERED SHIM dur-
ing INSPECTION 7 (a)
PART 1: OPEN ACCESS
PART 5: SEALANT REMOVAL
-ACTION 2: Repeat
INSPECTION 5
and INSPECTION
6. -FIGURE 3, FIGURE 4,FIGURE 15, FIGURE
16, FIGURE 17, FIG-
URE 18, FIGURE 25,
FIGURE 26, FIGURE
29, FIGURE 30, FIG-
URE 39, FIGURE 40
PART 6: SEALANT APPLICATION-
PART 2: CLOSE ACCESS
PART 1: OPEN ACCESS-Repeat INSPEC-
TION 5 and IN-
SPECTION 6.
CONDITION 309: TA-
PERED SHIM IS NOT
MISSING AND TAPERED
SHIM IS NOT MADE FROM
LAMINATED MATERIAL
AND WIDTH OF TAPERED
SHIM IS 1.70 INCHES OR
MORE AND NO DAMAGE
AND NO CORROSION
FOUND ON THE TA-
PERED SHIM during IN-
SPECTION 7 (a)
PART 5: SEALANT REMOVAL
-FIGURE 3, FIGURE 4,
FIGURE 15, FIGURE
16, FIGURE 17, FIG-
URE 18, FIGURE 25,
FIGURE 26, FIGURE
29, FIGURE 30, FIG-
URE 39, FIGURE 40
PART 6: SEALANT APPLICATION
PART 2: CLOSE ACCESS
-
CMM 57-53-15-ACTION 1: Repair
the flap track.
CONDITION 310: ANY
CORROSION OR ANY
CRACK FOUND ON THE
FLAP TRACK THAT IS IN
THE REPAIR LIMITS OF
CMM 57-53-15 during IN-
SPECTION 7 (a)(c)
(c)
PART 1: OPEN ACCESS
PART 5: SEALANT REMOVAL
-ACTION 2: Repeat
INSPECTION 5
and INSPECTION
6. -FIGURE 3, FIGURE 4,FIGURE 15, FIGURE
16, FIGURE 17, FIG-
URE 18, FIGURE 25,
FIGURE 26, FIGURE
29, FIGURE 30, FIG-
URE 39, FIGURE 40
PART 6: SEALANT APPLICATION-
PART 2: CLOSE ACCESS
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 25, 2017
737-57A1338 RB
56 of 161
REQUIREMENTS BULLETIN 737-57A1338
ALERTALERT

### Page 57

Group 2; Group 3, Configuration 1:
Table 3: Detailed Inspections and NDT Inspections of the Outboard Flap Tracks at Positions 2 and 7
Refer to the listed procedures in
SB 737-57A1338 Original Issue or
later approved revisions as an
accepted procedure:
Method of Compli-
ance
ActionCondition
737-100/200 AMM 27-51-151 or
737-300/400/500 AMM 27-51-49
-Remove the flap
track and install a
new or serviceable
flap track. (b)
CONDITION 311: ANY
CORROSION OR ANY
CRACK FOUND ON THE
FLAP TRACK THAT IS
LARGER THAN THE RE-
PAIR LIMITS OF CMM 57-
53-15 during INSPECTION
7 (a)(c)
PART 1: OPEN ACCESS-Repeat INSPEC-
TION 5 and IN-
SPECTION 6.
CONDITION 312: NO
CORROSION AND NO
CRACK FOUND ON THE
FLAP TRACK during IN-
SPECTION 7 (a)
PART 5: SEALANT REMOVAL
-FIGURE 3, FIGURE 4,
FIGURE 15, FIGURE
16, FIGURE 17, FIG-
URE 18, FIGURE 25,
FIGURE 26, FIGURE
29, FIGURE 30, FIG-
URE 39, FIGURE 40
PART 6: SEALANT APPLICATION-
PART 2: CLOSE ACCESS
CMM 57-53-15, and 737-100/200
AMM 27-51-151 or 737-300/400/500
AMM 27-51-49
-ACTION 1: Re-
move the bushing
and install a new or
serviceable bush-
ing.
CONDITION 313: ANY
CORROSION FOUND ON
THE BUSHING during IN-
SPECTION 7 (a) (c)
PART 1: OPEN ACCESS-ACTION 2: Repeat
INSPECTION 5
and INSPECTION
6.
PART 5: SEALANT REMOVAL
-FIGURE 3, FIGURE 4,
FIGURE 15, FIGURE
16, FIGURE 17, FIG-
URE 18, FIGURE 25,
FIGURE 26, FIGURE
29, FIGURE 30, FIG-
URE 39, FIGURE 40
PART 6: SEALANT APPLICATION-
PART 2: CLOSE ACCESS
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 25, 2017
737-57A1338 RB
57 of 161
REQUIREMENTS BULLETIN 737-57A1338
ALERTALERT

### Page 58

Group 2; Group 3, Configuration 1:
Table 3: Detailed Inspections and NDT Inspections of the Outboard Flap Tracks at Positions 2 and 7
Refer to the listed procedures in
SB 737-57A1338 Original Issue or
later approved revisions as an
accepted procedure:
Method of Compli-
ance
ActionCondition
PART 1: OPEN ACCESS-Repeat INSPEC-
TION 5 and IN-
SPECTION 6.
CONDITION 314: NO
CORROSION FOUND ON
THE BUSHING during IN-
SPECTION 7 (a)
PART 5: SEALANT REMOVAL
-FIGURE 3, FIGURE 4,
FIGURE 15, FIGURE
16, FIGURE 17, FIG-
URE 18, FIGURE 25,
FIGURE 26, FIGURE
29, FIGURE 30, FIG-
URE 39, FIGURE 40
PART 6: SEALANT APPLICATION-
PART 2: CLOSE ACCESS
737-100/200 AMM 27-51-151 or
737-300/400/500 AMM 27-51-49
-Remove the flap
track and install a
new or serviceable
flap track. (b)
CONDITION 315: FLAP
TRACK CANNOT BE PUT
BACK TO A SERVICE-
ABLE CONDITION during
overhaul (a)
CMM 57-53-15-Repeat the over-
haul of the flap
track.
CONDITION 316: FLAP
TRACK FOUND SERVICE-
ABLE OR PUT BACK TO A
SERVICEABLE CONDI-
TION during overhaul (a)
(c)
(a) More than one CONDITION can be applicable on each flap track.
(b) The replacement flap track, whether new or serviceable, must be in compliance with the initial inspection
requirements and compliance times based on the applicable flap track condition. Inspections and overhauls
previously accomplished in accordance with Requirements Bulletin 737-57A1338 RB can be used to sat-
isfy these requirements, so long as the track continues to comply with repeat intervals specified in the table.
For Group 3 airplanes, replacement of the flap track could result in a change in Configuration. Comply
with all requirements specified in the table for the Configuration of the flap track installed.
(c) CMM 57-53-15, Revision 44, dated March 1, 2016 and Temporary Revision 57-3003, dated August 18,
2017, or later revisions.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 25, 2017
737-57A1338 RB
58 of 161
REQUIREMENTS BULLETIN 737-57A1338
ALERTALERT

### Page 59

Group 3, Configuration 2:
The actions required for each INSPECTION in Table 4 are identified as follows:
Group 3, Configuration 2:
ActionTitle
Do a surface HFEC inspection of the flap track flanges and webs, and an open hole
HFEC inspection of the flap track webs for any crack.
INSPECTION 8
ACTION 1: Do a detailed inspection of the flap track flanges and webs for any crack,
any nick, any corrosion pit, any galling, any piece broken off, and any stop-drill repair.
INSPECTION 9 (a)
ACTION 2: Do a surface HFEC inspection of the flap track flanges and webs for any
crack.
ACTION 3: Do a surface HFEC inspection and an ultrasonic inspection of the upper
flap track flange for any crack.
ACTION 4: Do a detailed inspection of the anti-fret strip and the tapered shim for any
damage and any corrosion.
ACTION 5: Do a detailed inspection of the flap track at the rear spar attachment for
any crack, any corrosion and any loose fastener.
ACTION 1: Do a detailed inspection of the anti-fret strip for presence or absence of
the anti-fret strip and for any damage and for material.
INSPECTION 10 (a)
ACTION 2: Do a detailed inspection of the tapered shim for presence or absence, any
damage, any corrosion, and for material, and measure the width of the tapered shim
normal to its aft edge.
ACTION 3: Do a detailed inspection of the flap track in the area of the rear spar attach-
ment mating surface for any corrosion.
ACTION 4: Do a detailed inspection of the outer circumferential surface of the bushing
for any corrosion.
ACTION 5: Do a surface HFEC inspection and an open hole HFEC inspection of the
flap track for any crack.
(a) This INSPECTION is related to SB 737-57A1271.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 25, 2017
737-57A1338 RB
59 of 161
REQUIREMENTS BULLETIN 737-57A1338
ALERTALERT

### Page 60

Group 3, Configuration 2:
Table 4: Detailed Inspections and NDT Inspections of the Outboard Flap Tracks at Positions 2 and 7
Refer to the listed procedures in
SB 737-57A1338 Original Issue or
later approved revisions as an
accepted procedure:
Method of Compli-
ance
ActionCondition
PART 1: OPEN ACCESS-ACTION 1: Do IN-
SPECTION 8 on
each affected flap
track.
Airplanes with flap tracks on
which an overhaul was
done
PART 3: FASTENER REMOVAL
-FIGURE 21, FIGURE
22
PART 4: FASTENER INSTALLA-
TION
-
PART 2: CLOSE ACCESS
PART 1: OPEN ACCESS-ACTION 2: Do IN-
SPECTION 9 on
each affected flap
track.
PART 5: SEALANT REMOVAL
-FIGURE 3, FIGURE 4,
FIGURE 25, FIGURE
26, FIGURE 29, FIG-
URE 30, FIGURE 39,
FIGURE 40
PART 6: SEALANT APPLICATION-
PART 2: CLOSE ACCESS
CMM 57-53-15-ACTION 3: Do an
overhaul of each
affected flap track.
(c)
PART 1: OPEN ACCESS-ACTION 1: Do IN-
SPECTION 8 on
each affected flap
track.
Airplanes with flap tracks on
which no overhaul was
done and no inspection was
done in accordance with SB
737-57A1271
PART 3: FASTENER REMOVAL
-FIGURE 21, FIGURE
22
PART 4: FASTENER INSTALLA-
TION
-
PART 2: CLOSE ACCESS
PART 1: OPEN ACCESS-ACTION 2: Do IN-
SPECTION 9 on
each affected flap
track.
PART 5: SEALANT REMOVAL
-FIGURE 3, FIGURE 4,
FIGURE 25, FIGURE
26, FIGURE 29, FIG-
URE 30, FIGURE 39,
FIGURE 40
PART 6: SEALANT APPLICATION-
PART 2: CLOSE ACCESS
CMM 57-53-15-ACTION 3: Do an
overhaul of each
affected flap track.
(c)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 25, 2017
737-57A1338 RB
60 of 161
REQUIREMENTS BULLETIN 737-57A1338
ALERTALERT

The text continues at https://openairdocs.org/service-documents/boeing/737-57a1338-rb/file/d1d6bf6041e4.md?from=61

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
