# Boeing Alert Requirements Bulletin 737-57A1339 RB: No revision named

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2018-0446; AD 2018-10-12 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Alert Requirements Bulletin 737-57A1339 RB](https://openairdocs.org/service-documents/boeing/737-57a1339-rb.md)
- Title as filed: 737-57A1339-00 RB--
- Pages: 24
- PDF: https://openairdocs.org/files/sha256/bb/92/bb927b80c5495005b637f784ac05e2e07144ed1a0a34bba3f03e420eba3b15d3
- Page: https://openairdocs.org/service-documents/boeing/737-57a1339-rb/file/bb927b80c549

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Commercial 
Airplanes
737
Requirements Bulletin
ALERT
Number: 737-57A1339 RB
Original Issue: April 16, 2018
ATA System: 5714 5312
SUBJECT: WINGS - Center Wing Box - Body Station 663.75 Aft Vertical Stiffeners and Keel Beam
Inspection
Export of this technology is controlled under the United States Export Administration Regulations (EAR) (15
CFR 300-774). An export license may be required before it is used for development, production or use by foreign
persons from specific countries. The controller of this data has the individual responsibility to abide by all export
laws.
9E991ECCN:
Copyright © 2018 Boeing.
Unpublished Work. All Rights Reserved.
Treatment of this document and its content is governed by contract with Boeing. Rights to use this document
are licensed on a per aircraft basis and such rights may not be transferable. For more information, contact The
Boeing Company.
Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner,
BBJ, DC-8, DC-9, DC-10, KC-10, KC-46, KDC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8, Poseidon and
Boeing liveries are all trademarks owned by The Boeing Company; and no trademark license is granted in
connection with this document unless provided in writing by Boeing.
Original Issue: April 16, 2018
737-57A1339 RB
1 of 24
3.0

### Page 2

Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 16, 2018
737-57A1339 RB
2 of 24
REQUIREMENTS BULLETIN 737-57A1339
ALERTALERT
BLANK PAGE

### Page 3

Table of Contents
1. EFFECTIVITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
A. Airplanes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
B. Spares Affected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2. CONCURRENT REQUIREMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3. COMPLIANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4. APPROVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
5. ACCOMPLISHMENT INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
A. General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
B. Work Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
FIGURE 1: CENTER WING BOX - AFT VERTICAL STIFFENERS - LBL 6.15 AND RBL 6.15 - INSPECTION
[Group 2, Configuration 1] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
FIGURE 2: CENTER WING BOX - AFT VERTICAL STIFFENERS AND TIME-LIMITED REPAIR - LBL 6.15
AND RBL 6.15 - INSPECTION [Group 2, Configuration 2] . . . . . . . . . . . . . . . . . . 20
FIGURE 3: BODY STATION 663.75 - KEEL BEAM UPPER CHORD AND ANGLE- LBL 6.50 AND RBL 6.50
- INSPECTION  [Group 2] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 16, 2018
737-57A1339 RB
3 of 24
REQUIREMENTS BULLETIN 737-57A1339
ALERTALERT

### Page 4

Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 16, 2018
737-57A1339 RB
4 of 24
REQUIREMENTS BULLETIN 737-57A1339
ALERTALERT
BLANK PAGE

### Page 5

Commercial 
Airplanes
737
Requirements Bulletin
ALERT
Number: 737-57A1339 RB
Original Issue: April 16, 2018
ATA System: 5714 5312
SUBJECT: WINGS - Center Wing Box - Body Station 663.75 Aft Vertical Stiffeners and Keel Beam
Inspection
THIS DOCUMENT IS SENT TO THE OPERATORS OF RECORD OF THE AIRPLANES SHOWN IN
PARAGRAPH 1.A., EFFECTIVITY. IF AN AIRPLANE HAS BEEN LEASED OR SOLD, SEND THIS DOCUMENT
TO THE NEW OPERATOR. IF APPLICABLE SPARES HAVE BEEN SOLD, SEND THIS DOCUMENT TO THE
NEW OWNER. THIS IS AN ENHANCED REQUIRED FOR COMPLIANCE DOCUMENT. THE BOEING
PROCESSES USED TO CREATE THE SERVICE BULLETIN (SB) AND THE REQUIREMENTS BULLETIN
(RB) ENSURE THAT THE INFORMATION BETWEEN "RC START" AND "RC END" IN THE SB ARE IDENTICAL
TO THE INFORMATION IN THE SAME SECTIONS (COMPLIANCE, WORK INSTRUCTIONS…) OF THE RB
WHICH THE SB REFERS TO AS THE RELATED DOCUMENT.
1. EFFECTIVITY
A. Airplanes
This bulletin is applicable to all 737-100/-200/-200C/-300/-400/-500 Airplanes, line numbers 1 thru
3132.
DESCRIPTIONCONFIGURATIONGROUP
737-100/-200/-200C airplanes, line numbers 1 thru 291-1
737-200/-200C/-300/-400/-500 airplanes, line numbers 292 thru 3132-2
Airplanes with production aft vertical stiffeners that have Z cross
section, 69-62014-( ), installed.
1
Airplanes with production aft vertical stiffeners that have Z cross
section, 69-62014-( ), and with time-limited repair LOR-760 installed.
2
Airplanes with replacement aft vertical stiffeners that have J cross
section, 65C30036-( ), installed in accordance with Service Bulletin
(SB) 737-57A1269.
3
B. Spares Affected
None.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 16, 2018
737-57A1339 RB
5 of 24

### Page 6

2. CONCURRENT REQUIREMENTS
None.
3. COMPLIANCE
Federal Aviation Administration (FAA) Airworthiness Directive AD 2005-20-01 is related to Requirements
Bulletin 737-57A1339 RB. The effective date of AD 2005-20-01 is November 1, 2005.
The Federal Aviation Administration (FAA) will possibly release an additional Airworthiness Directive related
to Requirements Bulletin 737-57A1339 RB. The Airworthiness Directive will make the compliance tasks
and times given in Requirements Bulletin 737-57A1339 RB mandatory.
Accomplish the required actions, based on the applicable conditions in Tables 1 through 3 in accordance
with the Accomplishment Instructions.
When more than one OPTION is given for a CONDITION, do only one of the OPTION numbers. When
more than one ACTION is given for a CONDITION number or an OPTION number, do all of the ACTION
numbers for that CONDITION number or OPTION number.
Group 1:
Boeing endorses the FAA rules related to Limit of Validity (LOV) and recommends immediate and permanent
removal from service of any airplanes upon reaching the LOV, whether or not it is operated under FAA
jurisdiction. As such, Boeing no longer provides maintenance instructions for airplanes that have accumulated
flight cycles beyond the LOV. Airplanes in Group 1 (line numbers 1-291) have accumulated flight cycles
beyond the LOV of the maintenance program. 14 CFR 121.1115 and 129.115 prohibit operation of an
airplane beyond its LOV.
Group 2, Configuration 1:
Table 1: Surface High Frequency Eddy Current (HFEC) and Detailed Inspections of the Aft Vertical
Stiffeners at Left Buttock Line (LBL) 6.15 and Right Buttock Line (RBL) 6.15
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
-Within 500 flight
cycles after the
original issue date
of Requirements
Bulletin 737-
57A1339 RB.
Do surface HFEC and
detailed inspections of
the aft vertical stiffeners
for any crack.
All Airplanes
-Before further
flight.
ACTION 1: Contact The
Boeing Company for in-
structions and do the in-
structions.
CONDITION 101: ANY
CRACK FOUND ON THE
AFT VERTICAL STIFFEN-
ERS
-Before further
flight.
ACTION 2: Do a surface
HFEC inspection of the
keel beam upper chord
inboard flanges and a
general visual inspection
of the angle for any crack.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 16, 2018
737-57A1339 RB
6 of 24
REQUIREMENTS BULLETIN 737-57A1339
ALERTALERT

### Page 7

Group 2, Configuration 1:
Table 1: Surface High Frequency Eddy Current (HFEC) and Detailed Inspections of the Aft Vertical
Stiffeners at Left Buttock Line (LBL) 6.15 and Right Buttock Line (RBL) 6.15
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
-Before further
flight.
Contact The Boeing
Company for instructions
and do the instructions.
CONDITION 101.1: ANY
CRACK FOUND ON THE
KEEL BEAM UPPER
CHORD OR ANGLE
--No further action re-
quired.
CONDITION 101.2: NO
CRACK FOUND ON THE
KEEL BEAM UPPER
CHORD AND ANGLE
500 flight cycles.-Repeat the surface HFEC
and detailed inspections
of the aft vertical stiffen-
ers for any crack.
CONDITION 102: NO
CRACK FOUND ON THE
AFT VERTICAL STIFFEN-
ERS
Group 2, Configuration 2:
Table 2: Detailed Inspection of the Aft Vertical Stiffeners and Time-Limited Repair at LBL 6.15
and RBL 6.15
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
-Within 500 flight
cycles after the
original issue date
of Requirements
Bulletin 737-
57A1339 RB.
ACTION 1: Do a detailed
inspection of the aft verti-
cal stiffeners and time-
limited repair for any
crack.
All Airplanes
-Within 15,000 flight
cycles after the
time-limited repair
installation.
ACTION 2: Remove the
time-limited repair and
contact The Boeing
Company for instructions
and do the instructions.
-Before further
flight.
ACTION 1: Contact The
Boeing Company for in-
structions and do the in-
structions.
CONDITION 201: ANY
CRACK FOUND ON THE
AFT VERTICAL STIFFEN-
ERS OR TIME-LIMITED
REPAIR -Before further
flight.
ACTION 2: Do a surface
HFEC inspection of the
keel beam upper chord
inboard flanges and a
general visual inspection
of the angle for any crack.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 16, 2018
737-57A1339 RB
7 of 24
REQUIREMENTS BULLETIN 737-57A1339
ALERTALERT

### Page 8

Group 2, Configuration 2:
Table 2: Detailed Inspection of the Aft Vertical Stiffeners and Time-Limited Repair at LBL 6.15
and RBL 6.15
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
-Before further
flight.
Contact The Boeing
Company for instructions
and do the instructions.
CONDITION 201.1: ANY
CRACK FOUND ON THE
KEEL BEAM UPPER
CHORD OR ANGLE
--No further action re-
quired.
CONDITION 201.2: NO
CRACK FOUND ON THE
KEEL BEAM UPPER
CHORD AND ANGLE
500 flight cycles (a)-Repeat the detailed in-
spection of the aft vertical
stiffeners and time-limited
repair for any crack. (a)
CONDITION 202: NO
CRACK FOUND ON THE
AFT VERTICAL STIFFEN-
ERS AND TIME-LIMITED
REPAIR
(a) The repeat detailed inspection of the aft vertical stiffeners and time-limited repair is valid
until the accomplishment of ACTION 2: Remove the time-limited repair and contact The
Boeing Company for instructions and do the instructions.
Group 2:
Table 3: Surface HFEC Inspection of the Keel Beam Upper Chord and General Visual Inspection
of the Angle at LBL 6.50 and RBL 6.50
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
-Within 500 flight
cycles after the
original issue date
of Requirements
Bulletin 737-
57A1339 RB.
Do a surface HFEC in-
spection of the keel beam
upper chord inboard
flanges and a general vi-
sual inspection of the an-
gle for any crack.
All Airplanes
-Before further
flight.
Contact The Boeing
Company for instructions
and do the instructions.
CONDITION 301: ANY
CRACK FOUND ON THE
KEEL BEAM UPPER
CHORD OR ANGLE
--No further action re-
quired.
CONDITION 302: NO
CRACK FOUND ON THE
KEEL BEAM UPPER
CHORD AND ANGLE
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 16, 2018
737-57A1339 RB
8 of 24
REQUIREMENTS BULLETIN 737-57A1339
ALERTALERT

### Page 9

4. APPROVAL
This Requirements Bulletin was examined by the Federal Aviation Administration (FAA). The changes
specified in this document comply with the applicable regulations and are FAA approved, as well as European
Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved
airplanes listed in the service bulletin effectivity. This document and its approval were based on the airplane
in its original Boeing delivery configuration or as modified by other Boeing changes.
If an airplane has a non-Boeing modification or repair that affects a component or system also affected by
this Requirements Bulletin, the operator is responsible for obtaining appropriate regulatory agency approval
before incorporating this Requirements Bulletin.
In addition, the Manager of the FAA Los Angeles ACO Branch approves the action (i.e. inspection or
modification) defined in this service bulletin as an alternative method of compliance to the requirements of
paragraph (g) of AD 2005-20-01. All provisions of AD 2005-20-01 that are not specifically referenced in the
above statement remain fully applicable and must be complied with.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 16, 2018
737-57A1339 RB
9 of 24
REQUIREMENTS BULLETIN 737-57A1339
ALERTALERT

### Page 10

Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 16, 2018
737-57A1339 RB
10 of 24
REQUIREMENTS BULLETIN 737-57A1339
ALERTALERT
BLANK PAGE

### Page 11

5.    ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL INFORMATION
NOTE: 6. Unless shown differently, these dimensions and tolerances are used:
– Linear dimensions are in inches
– Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus
or minus 0.03 inch
– Tolerance on rivet and bolt edge margin is plus or minus 0.05 inch
– Angular tolerance is plus or minus 2 degrees
– Hole dimensions for standard solid rivets and fasteners are in Structural Repair
Manual (SRM) Chapter 51
– Torque Values:
— Values for structural fasteners are given in 737 Structural Repair Manual,
Chapter 51.
— Values for airframe maintenance tasks are included in Chapter 20 of 737
Aircraft Maintenance Manual (AMM).
— Values for electrical maintenance tasks are included in Chapter 20 of
Standard Wiring Practices Manual (SWPM).
— Values for engine maintenance tasks are included in Chapter 70 of 737
Aircraft Maintenance Manual (AMM).
— Non-standard torque values for maintenance tasks are included in the
applicable installation step.
7. Use the approved fastener, process and material substitutions in accordance with
SRM Chapter 51.
8. If the length of any fastener specified in this service bulletin does not meet installation
standards given in SRM Chapter 51, then a fastener of the same specification, or
an approved substitute, with a length which meets the installation standards given
in SRM Chapter 51 may be used. In addition, washers may be installed for fastener
grip length in accordance with SRM Chapter 51. Refer to SOPM 20-50-01 for alternate
full threaded fasteners (screws) needed for installation in this service bulletin.
9. A Detailed Inspection is defined as: An intensive examination of a specific item,
installation, or assembly to detect damage, failure, or irregularity. Available lighting
is normally supplemented with a direct source of good lighting at an intensity deemed
appropriate. Inspection aids such as mirrors, magnifying lenses, etc. may be
necessary. Surface cleaning and elaborate procedures may be required.
10. A General Visual Inspection is defined as: A visual examination of an interior or
exterior area, installation or assembly to detect obvious damage, failure or irregularity.
This level of inspection is made from within touching distance unless otherwise
specified. A mirror may be necessary to enhance visual access to all exposed surfaces
in the inspection area. This level of inspection is made under normally available
lighting conditions such as daylight, hangar lighting, flashlight or drop-light and may
require removal or opening of access panels or doors. Stands, ladders or platforms
may be required to gain proximity to the area being checked.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 16, 2018
737-57A1339 RB
11 of 24
REQUIREMENTS BULLETIN 737-57A1339
ALERTALERT

### Page 12

11. These work instructions refer to procedures included in other Boeing documents.
When the words "refer to" are used and the operator has an accepted alternative
procedure, the accepted alternative procedure can be used. When the words "in
accordance with" are included in the instruction, the procedure in the Boeing document
must be used.
12. Boeing Service Letter 737-SL-51-048, Damage Reporting and Repair Plan/Design
Guidelines, is an acceptable procedure to request information from Boeing for
additional structural repair instructions. The Service Letter describes what information
must be provided to Boeing before a structural repair can be provided.
13. The instructions in Paragraph 3.B., Work Instructions and the figures can include
operation of tools or test equipment. Boeing Engineering Tool Drawings, the Illustrated
Tool and Equipment Manual, and the Special Tool and Ground Handling Drawing
Index contain data on versions of the tools or test equipment that you can use. It is
permitted to use replaced tools. It is not permitted to use superseded tools.
14. If it is necessary to remove more parts for access, you can remove those parts. If
you can get access without removing identified parts, it is not necessary to remove
all of the identified parts. Jacking and shoring limitations must be observed.
15. Where the work instructions include installation of a kept part, a new or serviceable
part with the same part number can be installed as an alternative to the kept part.
16. When more than one OPTION is given for a CONDITION, do only one of the OPTION
numbers. When more than one ACTION is given for a CONDITION number or an
OPTION number, do all of the ACTION numbers for that CONDITION number or
OPTION number.
17. This is an Enhanced Required for Compliance document. There will be a separate
Service Bulletin (SB) and a separate Requirements Bulletin (RB). If an RB is mandated
by an Airworthiness Directive (AD), then all applicable requirements specified in the
RB must be done. For the related SB, some locations are marked RC Start and RC
End to identify the requirements that are restated from the RB. For the related SB,
the areas between RC Start and RC End, including sub-steps and any figures
identified between RC Start and RC End, must be done to comply with the AD.
Therefore, an Alternative Method of Compliance (AMOC) is required for any deviations
to steps between RC Start and RC End, including substeps and identified figures.
For the related SB, the steps not between RC Start and RC End may be deviated
from using accepted methods in accordance with the operator's maintenance or
inspection program without obtaining approval of an AMOC; this is provided that the
steps between RC Start and RC End, including sub-steps and identified figures, can
still be done as specified, and the airplane can be put back in an airworthy condition.
Figures not required for compliance are omitted from the RB.
18. This is an Enhanced Required for Compliance document. The Boeing processes
used to create the Service Bulletin (SB) and the Requirements Bulletin (RB) ensure
that the information between "RC Start" and "RC End" in the SB are identical to the
information in the same sections (Compliance, Work Instructions...) of the RB which
the SB refers to as the related document.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 16, 2018
737-57A1339 RB
12 of 24
REQUIREMENTS BULLETIN 737-57A1339
ALERTALERT

### Page 13

B. WORK INSTRUCTIONS
Actions Required for Compliance
1. Requirements
Group 1:
Boeing endorses the FAA rules related to Limit of Validity (LOV) and recommends immediate and
permanent removal from service of any airplanes upon reaching the LOV, whether or not it is
operated under FAA jurisdiction. As such, Boeing no longer provides maintenance instructions for
airplanes that have accumulated flight cycles beyond the LOV. Airplanes in Group 1 (line numbers
1-291) have accumulated flight cycles beyond the LOV of the maintenance program. 14 CFR
121.1115 and 129.115 prohibit operation of an airplane beyond its LOV.
Group 2, Configuration 1:
Table 1: Surface High Frequency Eddy Current (HFEC) and Detailed Inspections of the Aft Vertical
Stiffeners at Left Buttock Line (LBL) 6.15 and Right Buttock Line (RBL) 6.15
Refer to the listed
procedures in SB
737-57A1339
Original Issue or
later approved re-
visions as an ac-
cepted proce-
dure:
Method of Compli-
ance
ActionCondition
PART 1: OPEN
ACCESS
-Do surface HFEC and
detailed inspections of
the aft vertical stiffeners
for any crack.
All Airplanes
-FIGURE 1
--ACTION 1: Contact The
Boeing Company for in-
structions and do the in-
structions.
CONDITION 101: ANY
CRACK FOUND ON THE
AFT VERTICAL STIFFEN-
ERS
PART 1: OPEN
ACCESS
-ACTION 2: Do a surface
HFEC inspection of the
keel beam upper chord
inboard flanges and a
general visual inspection
of the angle for any crack.
-FIGURE 3
--Contact The Boeing
Company for instructions
and do the instructions.
CONDITION 101.1: ANY
CRACK FOUND ON THE
KEEL BEAM UPPER
CHORD OR ANGLE
PART 2: CLOSE
ACCESS
-No further action re-
quired.
CONDITION 101.2: NO
CRACK FOUND ON THE
KEEL BEAM UPPER
CHORD AND ANGLE
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 16, 2018
737-57A1339 RB
13 of 24
REQUIREMENTS BULLETIN 737-57A1339
ALERTALERT

### Page 14

Group 2, Configuration 1:
Table 1: Surface High Frequency Eddy Current (HFEC) and Detailed Inspections of the Aft Vertical
Stiffeners at Left Buttock Line (LBL) 6.15 and Right Buttock Line (RBL) 6.15
Refer to the listed
procedures in SB
737-57A1339
Original Issue or
later approved re-
visions as an ac-
cepted proce-
dure:
Method of Compli-
ance
ActionCondition
-FIGURE 1Repeat the surface HFEC
and detailed inspections
of the aft vertical stiffen-
ers for any crack.
CONDITION 102: NO
CRACK FOUND ON THE
AFT VERTICAL STIFFEN-
ERS
PART 2: CLOSE
ACCESS
-
Group 2, Configuration 2:
Table 2: Detailed Inspection of the Aft Vertical Stiffeners and Time-Limited Repair at LBL 6.15
and RBL 6.15
Refer to the listed
procedures in SB
737-57A1339
Original Issue or
later approved re-
visions as an ac-
cepted proce-
dure:
Method of Compli-
ance
ActionCondition
PART 1: OPEN
ACCESS
-ACTION 1: Do a detailed
inspection of the aft verti-
cal stiffeners and time-
limited repair for any
crack.
All Airplanes
-FIGURE 2
--ACTION 2: Remove the
time-limited repair and
contact The Boeing
Company for instructions
and do the instructions.
--ACTION 1: Contact The
Boeing Company for in-
structions and do the in-
structions.
CONDITION 201: ANY
CRACK FOUND ON THE
AFT VERTICAL STIFFEN-
ERS OR TIME-LIMITED
REPAIR PART 1: OPEN
ACCESS
-ACTION 2: Do a surface
HFEC inspection of the
keel beam upper chord
inboard flanges and a
general visual inspection
of the angle for any crack.
-FIGURE 3
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 16, 2018
737-57A1339 RB
14 of 24
REQUIREMENTS BULLETIN 737-57A1339
ALERTALERT

### Page 15

Group 2, Configuration 2:
Table 2: Detailed Inspection of the Aft Vertical Stiffeners and Time-Limited Repair at LBL 6.15
and RBL 6.15
Refer to the listed
procedures in SB
737-57A1339
Original Issue or
later approved re-
visions as an ac-
cepted proce-
dure:
Method of Compli-
ance
ActionCondition
--Contact The Boeing
Company for instructions
and do the instructions.
CONDITION 201.1: ANY
CRACK FOUND ON THE
KEEL BEAM UPPER
CHORD OR ANGLE
PART 2: CLOSE
ACCESS
-No further action re-
quired.
CONDITION 201.2: NO
CRACK FOUND ON THE
KEEL BEAM UPPER
CHORD AND ANGLE
-FIGURE 2Repeat the detailed in-
spection of the aft vertical
stiffeners and time-limited
repair for any crack. (a)
CONDITION 202: NO
CRACK FOUND ON THE
AFT VERTICAL STIFFEN-
ERS AND TIME-LIMITED
REPAIR
PART 2: CLOSE
ACCESS
-
(a) The repeat detailed inspection of the aft vertical stiffeners and time-limited repair is valid
until the accomplishment of ACTION 2: Remove the time-limited repair and contact The
Boeing Company for instructions and do the instructions.
Group 2:
Table 3: Surface HFEC Inspection of the Keel Beam Upper Chord and General Visual Inspection
of the Angle at LBL 6.50 and RBL 6.50
Refer to the listed
procedures in SB
737-57A1339
Original Issue or
later approved re-
visions as an ac-
cepted proce-
dure:
Method of Compli-
ance
ActionCondition
PART 1: OPEN
ACCESS
-Do a surface HFEC in-
spection of the keel beam
upper chord inboard
flanges and a general vi-
sual inspection of the an-
gle for any crack.
All Airplanes
-FIGURE 3
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 16, 2018
737-57A1339 RB
15 of 24
REQUIREMENTS BULLETIN 737-57A1339
ALERTALERT

### Page 16

Group 2:
Table 3: Surface HFEC Inspection of the Keel Beam Upper Chord and General Visual Inspection
of the Angle at LBL 6.50 and RBL 6.50
Refer to the listed
procedures in SB
737-57A1339
Original Issue or
later approved re-
visions as an ac-
cepted proce-
dure:
Method of Compli-
ance
ActionCondition
--Contact The Boeing
Company for instructions
and do the instructions.
CONDITION 301: ANY
CRACK FOUND ON THE
KEEL BEAM UPPER
CHORD OR ANGLE
PART 2: CLOSE
ACCESS
-No further action re-
quired.
CONDITION 302: NO
CRACK FOUND ON THE
KEEL BEAM UPPER
CHORD AND ANGLE
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 16, 2018
737-57A1339 RB
16 of 24
REQUIREMENTS BULLETIN 737-57A1339
ALERTALERT

### Page 17

This Figure applies only to: Group 2, Configuration 1.
FIGURE 1: CENTER WING BOX - AFT VERTICAL STIFFENERS - LBL 6.15 AND RBL 6.15 - INSPECTION
(SHEET 1 OF 3)
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 16, 2018
737-57A1339 RB
17 of 24
REQUIREMENTS BULLETIN 737-57A1339
ALERTALERT

### Page 18 (OCR)

REQUIREMENTS BULLETIN 737-57A1339
ALERT  ALERT
RBL
LBL  6.15
6.15
IBD
STIFFENER  WEB  WEB
LBL
STIFFENER  6.15
6.00 MIN TYP  1.50 MIN TYP  TYPICAL  B-B
6.50 MIN TYP  1.00 MIN TYP
WEB  WEB
RBL
6.15 STIFFENER
TYPICAL
C-C
VIEW LOOKING  _ DETAIL INSPECTION AREA
FORWARD  A-A  HFEC AND DETAILED  2810486
INSPECTION AREA
The step numbers shown below agree with the numbers shown in the circle symbols in the figure.
Step  Task  Name  Identification  Qty  More Data
1  Inspect  AFT VERTICAL STIFF-  2  (a)
ENER
2  Inspect  AFT VERTICAL STIFF-  2  (b)
ENER
FIGURE 1: CENTER WING BOX - AFT VERTICAL STIFFENERS - LBL 6.15 AND RBL 6.15 - INSPECTION
(SHEET 2 OF 3)
Original Issue: April 16, 2018
Export Controlled ECCN: 9E991  737-57A1339 RB
Copyright © Unpublished
Work - See page 1 for details.  18 of 24

### Page 19

More DataQtyIdentificationNameTaskStep
(a) Do a surface HFEC inspection around the fastener and inner radius for any crack in accordance with 737
NDT Manual PART 6, 51-00-00, Procedure 4 or 23.
(b) Do a detailed inspection for any crack. An inspection area covered by an existing bracket does not need
to be inspected.
FIGURE 1: CENTER WING BOX - AFT VERTICAL STIFFENERS - LBL 6.15 AND RBL 6.15 - INSPECTION
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 16, 2018
737-57A1339 RB
19 of 24
REQUIREMENTS BULLETIN 737-57A1339
ALERTALERT

### Page 20

This Figure applies only to: Group 2, Configuration 2.
FIGURE 2: CENTER WING BOX - AFT VERTICAL STIFFENERS AND TIME-LIMITED REPAIR - LBL 6.15
AND RBL 6.15 - INSPECTION
(SHEET 1 OF 3)
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 16, 2018
737-57A1339 RB
20 of 24
REQUIREMENTS BULLETIN 737-57A1339
ALERTALERT

### Page 21

The step numbers shown below agree with the numbers shown in the circle symbols in the figure.
More DataQtyIdentificationNameTaskStep
(a)--TIME-LIMITED RE-
PAIR
Inspect1
(b)2-AFT VERTICAL STIFF-
ENER
Inspect
FIGURE 2: CENTER WING BOX - AFT VERTICAL STIFFENERS AND TIME-LIMITED REPAIR - LBL 6.15
AND RBL 6.15 - INSPECTION
(SHEET 2 OF 3)
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 16, 2018
737-57A1339 RB
21 of 24
REQUIREMENTS BULLETIN 737-57A1339
ALERTALERT

### Page 22

More DataQtyIdentificationNameTaskStep
(a) Do a detailed inspection of the repair channels and straps for any crack. An inspection area covered by
an existing bracket does not need to be inspected.
(b) Do a detailed inspection of the aft vertical stiffener flanges common to the bulkhead for any crack. The
inspection of the stiffener flange is the length of the adjacent repair strap. This inspection does not include
the initial crack that required the installation of the time-limited repair.
FIGURE 2: CENTER WING BOX - AFT VERTICAL STIFFENERS AND TIME-LIMITED REPAIR - LBL 6.15
AND RBL 6.15 - INSPECTION
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 16, 2018
737-57A1339 RB
22 of 24
REQUIREMENTS BULLETIN 737-57A1339
ALERTALERT

### Page 23

This Figure applies only to: Group 2.
FIGURE 3: BODY STATION 663.75 - KEEL BEAM UPPER CHORD AND ANGLE- LBL 6.50 AND RBL 6.50
- INSPECTION
(SHEET 1 OF 2)
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 16, 2018
737-57A1339 RB
23 of 24
REQUIREMENTS BULLETIN 737-57A1339
ALERTALERT

### Page 24

The step numbers shown below agree with the numbers shown in the circle symbols in the figure.
More DataQtyIdentificationNameTaskStep
(a)2-KEEL BEAM UPPER
CHORD
Inspect1
(b)1-ANGLEInspect2
(a) Do a surface HFEC inspection along the inner radius of the upper chord inboard flanges for any crack in
accordance with 737 NDT Manual PART 6, 51-00-00, Procedure 4 or 23.
(b) Do a general visual inspection of the angle for any crack.
FIGURE 3: BODY STATION 663.75 - KEEL BEAM UPPER CHORD AND ANGLE- LBL 6.50 AND RBL 6.50
- INSPECTION
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 16, 2018
737-57A1339 RB
24 of 24
REQUIREMENTS BULLETIN 737-57A1339
ALERTALERT

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
