# Boeing Alert Requirements Bulletin 737-57A1348 RB: No revision named

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2020-0844; AD 2020-26-09 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Alert Requirements Bulletin 737-57A1348 RB](https://openairdocs.org/service-documents/boeing/737-57a1348-rb.md)
- Title as filed: 737-57A1348 RB--00
- Pages: 28
- PDF: https://openairdocs.org/files/sha256/28/9c/289ce4d06250b7e212ce0c5a842fdcc27721a0974057f43aeca3cfcaff252e70
- Page: https://openairdocs.org/service-documents/boeing/737-57a1348-rb/file/289ce4d06250

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Commercial 
Airplanes
737
Requirements Bulletin
ALERT
Number: 737-57A1348 RB
Original Issue: June 01, 2020
ATA System: 5714 5711
SUBJECT: WINGS - Center Wing Box - Rear Spar on Lower Wing Skin - Inspection
Export of this technology is controlled under the United States Export Administration Regulations (EAR) (15
CFR 300-774). An export license may be required before it is used for development, production or use by foreign
persons from specific countries. The controller of this data has the individual responsibility to abide by all export
laws.
9E991ECCN:
Copyright © 2020 Boeing.
Unpublished Work. All Rights Reserved.
Treatment of this document and its content is governed by contract with Boeing. Rights to use this document
are licensed on a per aircraft basis and such rights may not be transferable. For more information, contact The
Boeing Company.
Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner,
BBJ, DC-8, DC-9, DC-10, KC-10, KC-46, KDC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8, Poseidon and
Boeing liveries are all trademarks owned by The Boeing Company; and no trademark license is granted in
connection with this document unless provided in writing by Boeing.
Original Issue: June 01, 2020
737-57A1348 RB
1 of 28
3.0

### Page 2

Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 01, 2020
737-57A1348 RB
2 of 28
REQUIREMENTS BULLETIN 737-57A1348
ALERTALERT
BLANK PAGE

### Page 3

Table of Contents
1. EFFECTIVITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
A. Airplanes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
B. Spares Affected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2. CONCURRENT REQUIREMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3. COMPLIANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4. APPROVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5. ACCOMPLISHMENT INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
A. General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
B. Work Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
FIGURE 1: CENTER WING BOX - STA 663.75 REAR SPAR, LOWER SKIN AND LOWER CHORD -
EXTERNAL SURFACE HFEC AND ULTRASONIC INSPECTION [Group 2] . . . . . . . . 20
FIGURE 2: CENTER WING BOX - STA 663.75 REAR SPAR, LOWER SKIN AND LOWER CHORD -
INTERNAL DETAILED INSPECTION [Group 2] . . . . . . . . . . . . . . . . . . . . . . . 24
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 01, 2020
737-57A1348 RB
3 of 28
REQUIREMENTS BULLETIN 737-57A1348
ALERTALERT

### Page 4

Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 01, 2020
737-57A1348 RB
4 of 28
REQUIREMENTS BULLETIN 737-57A1348
ALERTALERT
BLANK PAGE

### Page 5

Commercial 
Airplanes
737
Requirements Bulletin
ALERT
Number: 737-57A1348 RB
Original Issue: June 01, 2020
ATA System: 5714 5711
SUBJECT: WINGS - Center Wing Box - Rear Spar on Lower Wing Skin - Inspection
THIS DOCUMENT IS SENT TO THE OPERATORS OF RECORD OF THE AIRPLANES SHOWN IN
PARAGRAPH 1.A., EFFECTIVITY . IF AN AIRPLANE HAS BEEN LEASED OR SOLD, SEND THIS DOCUMENT
TO THE NEW OPERATOR. IF APPLICABLE SPARES HAVE BEEN SOLD, SEND THIS DOCUMENT TO THE
NEW OWNER. THIS IS AN ENHANCED REQUIRED FOR COMPLIANCE DOCUMENT. THE BOEING
PROCESSES USED TO CREATE THE SERVICE BULLETIN (SB) AND THE REQUIREMENTS BULLETIN
(RB) ENSURE THAT THE INFORMATION BETWEEN "RC START" AND "RC END" IN THE SB ARE IDENTICAL
TO THE INFORMATION IN THE SAME SECTIONS (COMPLIANCE, WORK INSTRUCTIONS…) OF THE RB
WHICH THE SB REFERS TO AS THE RELATED DOCUMENT.
1. Effectivity
A. Airplanes
This bulletin is applicable to 737-100, 737-200, 737-200C, 737-300, 737-400, 737-500 Airplane(s),
line number(s) 1-3132 in 2 Group(s). Where the effectivity is presented with hyphens between line
numbers, the airplane applicability means "through" and "inclusive", e.g. line numbers 1-9 means
line numbers 1 through 9 inclusive.
DESCRIPTIONCONFIGURATIONGROUP
737-100/-200/-200C Airplanes beyond Limit Of Validity (LOV).-1
737-200/-200C/-300/-400/-500 Airplanes.-2
Airplane Models:
737-100, 737-200, 737-200C, 737-300, 737-400, 737-500
GroupVariable Number
1PA001 - PA022
1PA099
1PA231 - PA232
1PC001 - PC005
1PG001 - PG075
GroupVariable Number
1PG199
1PG201 - PG230
1PG251 - PG255
1PG271 - PG279
1PG301 - PG314
GroupVariable Number
1PG331 - PG332
1PG351 - PG356
1PG375
1PG401 - PG403
1PG431 - PG442
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 01, 2020
737-57A1348 RB
5 of 28

### Page 6

GroupVariable Number
1PG471 - PG475
1PG501 - PG505
1PG571 - PG583
2PG584 - PG586
1PG621 - PG630
1PG651 - PG652
1PG701 - PG705
2PH001
2PH011 - PH013
2PH021 - PH024
1PH701 - PH715
1PH731 - PH732
1PH741 - PH742
2PH743
1PJ001 - PJ002
2PJ003 - PJ009
1PJ031 - PJ032
1PJ071 - PJ072
1PJ101 - PJ104
2PJ105 - PJ119
2PJ201 - PJ219
2PJ301 - PJ302
2PJ551 - PJ561
2PJ601 - PJ615
2PJ811
2PJ816 - PJ817
2PK026 - PK029
2PK041 - PK053
2PK061 - PK070
2PK081 - PK082
2PK091 - PK099
2PK101 - PK103
2PK111 - PK120
GroupVariable Number
2PK141 - PK146
2PK201 - PK204
2PK211 - PK223
2PK231 - PK241
2PK251 - PK258
2PK271 - PK274
2PK281 - PK289
2PK291
2PK301 - PK318
2PK341
2PK351 - PK361
2PK391
2PK431 - PK433
2PK451 - PK452
2PK461 - PK469
2PK495
2PK501 - PK504
2PK511 - PK515
2PK519
2PK521 - PK528
2PK541 - PK565
2PK581
2PK591 - PK599
2PK601 - PK617
2PK621 - PK637
2PK641 - PK642
2PK661 - PK666
2PK671 - PK681
2PK691 - PK697
2PK711 - PK716
2PK731 - PK765
2PK771 - PK779
2PK801 - PK804
GroupVariable Number
2PK819 - PK827
2PK830
2PK861 - PK863
2PK871 - PK874
2PK881 - PK884
2PK901 - PK938
2PK971 - PK974
2PL001 - PL028
2PL061
2PL081
2PL101 - PL113
2PL151
2PL171 - PL172
2PL201 - PL203
2PL221
2PL401 - PL417
2PL421
2PL441
2PL451 - PL456
2PL471
2PL491
2PL501 - PL506
2PL551 - PL562
2PL581
2PL601 - PL603
2PL611
2PL621 - PL626
2PL631 - PL632
1PL711 - PL712
1PL716
2PL717 - PL747
2PL756
2PL758
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 01, 2020
737-57A1348 RB
6 of 28
REQUIREMENTS BULLETIN 737-57A1348
ALERTALERT

### Page 7

GroupVariable Number
2PL761 - PL770
2PL781 - PL788
2PL793
1PL801 - PL803
2PM001 - PM006
2PM016 - PM017
2PM021 - PM023
2PM051 - PM066
2PM101 - PM119
2PM141 - PM142
2PM171
2PM181
2PM251 - PM255
2PM281 - PM283
2PM381 - PM399
2PM401 - PM417
2PM541 - PM564
2PN001 - PN002
2PN021 - PN043
2PN081 - PN086
2PN101 - PN117
2PN131 - PN163
2PN401 - PN420
2PN431 - PN433
2PN451 - PN456
2PN471 - PN474
2PN481
2PN491 - PN493
2PN501 - PN502
2PN511 - PN512
2PN521
2PP001 - PP054
2PP101 - PP169
GroupVariable Number
2PP181 - PP199
2PP201 - PP205
2PP221
2PP231 - PP243
2PP281 - PP286
2PP301 - PP305
2PP351 - PP353
2PP376 - PP384
2PP391 - PP393
2PP401 - PP440
2PP471 - PP475
2PP501 - PP522
2PP631 - PP634
2PP651 - PP652
2PP671 - PP699
2PP701 - PP733
2PP771 - PP779
2PP801 - PP808
2PP821 - PP827
2PP831 - PP848
2PP851 - PP852
2PP861 - PP877
2PP891 - PP899
2PP901 - PP936
2PP946 - PP948
2PP951 - PP952
2PP961 - PP967
2PP981 - PP991
2PP993
2PQ001 - PQ016
2PQ026 - PQ041
2PQ051 - PQ092
2PQ101 - PQ199
GroupVariable Number
2PQ201 - PQ202
2PQ221 - PQ237
2PQ241 - PQ243
2PQ251 - PQ267
2PQ281 - PQ299
2PQ301 - PQ307
2PQ331 - PQ332
2PQ341 - PQ348
2PQ361 - PQ373
2PQ391 - PQ395
2PQ401 - PQ418
2PQ421
2PQ431 - PQ438
2PQ447 - PQ448
2PQ451
2PQ454
2PQ471 - PQ475
2PQ479 - PQ481
2PQ486 - PQ487
2PQ491 - PQ493
2PQ771 - PQ772
2PQ791 - PQ793
2PQ801 - PQ805
2PQ931 - PQ935
2PQ951
2PQ971 - PQ997
2PR001 - PR017
2PR021 - PR034
2PR041 - PR045
2PR061 - PR072
2PR077 - PR082
2PR091 - PR092
2PR096
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 01, 2020
737-57A1348 RB
7 of 28
REQUIREMENTS BULLETIN 737-57A1348
ALERTALERT

### Page 8

GroupVariable Number
2PR101
2PR121 - PR122
2PR131 - PR132
2PR141 - PR143
2PR161 - PR172
2PR181
2PS601 - PS631
2PS636 - PS638
2PS641 - PS644
2PS651 - PS657
2PS666 - PS669
2PS691 - PS692
2PS701 - PS706
2PS751 - PS799
2PS811
2PS836 - PS837
2PS841 - PS846
2PS851 - PS852
2PS856
2PS861 - PS863
2PS866 - PS868
2PS871 - PS874
2PS896 - PS897
2PS901 - PS941
2PS956 - PS957
2PS961 - PS963
2PS971 - PS978
2PT001 - PT015
2PT021 - PT031
2PT041 - PT064
2PT101 - PT105
2PT121 - PT138
2PT146 - PT148
GroupVariable Number
2PT161 - PT170
2PT181 - PT188
2PT211 - PT220
2PT295
2PT301 - PT309
2PT331 - PT360
2PT381 - PT399
2PT401 - PT438
2PT501 - PT517
2PT561 - PT565
2PT581 - PT586
2PT611 - PT621
2PT641 - PT644
2PT651 - PT656
2PT671 - PT672
2PT681 - PT685
2PT701 - PT703
2PT716 - PT717
2PT721 - PT725
2PT801 - PT834
2PT851 - PT854
2PT871 - PT886
2PT901 - PT930
2PT971 - PT973
2PT981 - PT985
2PT996
2PU001 - PU025
2PU301
2PU311 - PU313
2PV001 - PV055
2PV201 - PV209
2PV226 - PV229
2PV231 - PV237
GroupVariable Number
2PV271 - PV272
2PV281 - PV287
2PV296
2PV301 - PV302
2PV351
2PV356 - PV357
2PW001 - PW054
2PW061 - PW068
2PW072
2PW086 - PW088
2PW091 - PW094
2PW101 - PW102
2PW106
2PW111 - PW120
2PW156 - PW157
2PW161 - PW171
2PW201 - PW252
2PW261 - PW268
2PW271 - PW276
2PW278
2PW281 - PW293
2PW296
2PW301 - PW327
2PW401 - PW408
2PW411 - PW418
2PW421 - PW424
2PW431 - PW435
2PW441 - PW450
2PW461 - PW467
2PW501 - PW504
2PW511 - PW522
2PW524 - PW550
2PW556 - PW557
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 01, 2020
737-57A1348 RB
8 of 28
REQUIREMENTS BULLETIN 737-57A1348
ALERTALERT

### Page 9

GroupVariable Number
2PW561 - PW564
2PW571 - PW576
2PW591 - PW596
2PW611 - PW622
2PW631 - PW637
2PW661 - PW662
2PW681 - PW683
2PW701 - PW702
2PW711 - PW717
2PW741 - PW742
2PW761
2PW771
2PW831
2PW851 - PW856
1PX071
1PX701
1PY001 - PY008
1PY021
2PY022
1PY031
GroupVariable Number
2PY036 - PY037
2PY046 - PY048
2PY051 - PY053
2PY056 - PY057
2PY101 - PY103
2PY111 - PY113
2PY131 - PY135
2PY141 - PY143
2PY151 - PY154
2PY156 - PY157
2PY161 - PY162
2PY166
2PY191
2PY201
2PY221 - PY222
2PY231
2PY241 - PY244
2PY270 - PY275
2PY281
2PY286
GroupVariable Number
1PY301 - PY304
1PY321 - PY323
1PY341 - PY346
1PY361 - PY362
1PY381
2PY401
2PY409 - PY411
2PY421 - PY422
2PY441
2PY451
2PY461 - PY463
2PY591 - PY595
2PY611 - PY612
2PY621
2PY631
2PY651
2PY671 - PY672
2PY721
2PY741
--
B. Spares Affected
None.
2. CONCURRENT REQUIREMENTS
None.
3. COMPLIANCE
The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to
Requirements Bulletin 737-57A1348 RB. The Airworthiness Directive will make the compliance tasks and
times given in Requirements Bulletin 737-57A1348 RB mandatory.
Accomplish the required actions, based on the applicable conditions in Table 1, in accordance with
Accomplishment Instructions.
When more than one OPTION is given for a CONDITION, do only one of the OPTION numbers. When
more than one ACTION is given for a CONDITION or an OPTION, do all of the ACTION numbers for that
CONDITION or OPTION.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 01, 2020
737-57A1348 RB
9 of 28
REQUIREMENTS BULLETIN 737-57A1348
ALERTALERT

### Page 10

Group 1:
Boeing endorses the FAA rules related to Limit of Validity (LOV) and recommends immediate and permanent
removal from service of any airplanes upon reaching the LOV, whether or not it is operated under FAA
jurisdiction. As such, Boeing no longer provides maintenance instructions for airplanes that have accumulated
flight cycles beyond the LOV. Airplanes in Group 1 (line numbers 1-291) have accumulated flight cycles
beyond the LOV of the maintenance program. 14 CFR 121.1115 and 129.115 prohibit operation of an
airplane beyond its LOV.
Group 2:
Table 1: External or Internal Inspection of the Center Wing Box, Station (STA) 663.75 Rear Spar, Lower
Skin and Lower Chord
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Within 3,000
flight cycles af-
ter the original
issue date of
Requirements
Bulletin 737-
57A1348 RB.
Before 45,000
total flight cy-
cles.
OPTION 1:
Do an external surface High
Frequency Eddy Current
(HFEC) inspection and ultra-
sonic inspection of the center
wing box, STA 663.75 rear
spar, lower skin and lower
chord for any crack.
All airplanes.
OPTION 2:
Do an internal detailed inspec-
tion of the center wing box,
STA 663.75 rear spar, lower
skin and lower chord for any
crack.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 01, 2020
737-57A1348 RB
10 of 28
REQUIREMENTS BULLETIN 737-57A1348
ALERTALERT

### Page 11

Group 2:
Table 1: External or Internal Inspection of the Center Wing Box, Station (STA) 663.75 Rear Spar, Lower
Skin and Lower Chord
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flight.CONDITION 1 (ACTION 1):CONDITION 1: ANY
CRACK FOUND DUR-
ING THE EXTERNAL
INSPECTION.
Contact The Boeing Compa-
ny for repair instructions and
do the repair.
9,000 flight cycles.-CONDITION 1 ACTION 2
(OPTION 1):
Repeat external surface High
Frequency Eddy Current
(HFEC) inspection and ultra-
sonic inspection of the center
wing box, STA 663.75 rear
spar, lower skin and lower
chord for any crack at the un-
repaired areas. (a)(b)
-Within 9,000 flight cycles after the
most recent OPTION 1 inspection
was done.
CONDITION 1 ACTION 2
(OPTION 2):
Do an internal detailed inspec-
tion of the center wing box,
STA 663.75 rear spar, lower
skin and lower chord for any
crack at the unrepaired areas.
(b)(c)
9,000 flight cycles.-CONDITION 2 (OPTION 1):CONDITION 2: NO
CRACK FOUND DUR-
ING EXTERNAL IN-
SPECTION.
Repeat external surface High
Frequency Eddy Current
(HFEC) inspection and ultra-
sonic inspection of the center
wing box, STA 663.75 rear
spar, lower skin and lower
chord for any crack. (a)(b)
-Within 9,000 flight cycles after the
most recent OPTION 1 inspection
was done.
CONDITION 2 (OPTION 2):
Do an internal detailed inspec-
tion of the center wing box,
STA 663.75 rear spar, lower
skin and lower chord for any
crack. (c)(b)
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 01, 2020
737-57A1348 RB
11 of 28
REQUIREMENTS BULLETIN 737-57A1348
ALERTALERT

### Page 12

Group 2:
Table 1: External or Internal Inspection of the Center Wing Box, Station (STA) 663.75 Rear Spar, Lower
Skin and Lower Chord
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flight.CONDITION 3 (ACTION 1):CONDITION 3: ANY
CRACK FOUND DUR-
ING THE INTERNAL
INSPECTION.
Contact The Boeing Compa-
ny for repair instructions and
do the repair.
-Within 12,000 flight cycles after
the most recent OPTION 2 inspec-
tion was done.
CONDITION 3 ACTION 2
(OPTION 1):
Do an external surface High
Frequency Eddy Current
(HFEC) inspection and ultra-
sonic inspection of the center
wing box, STA 663.75 rear
spar, lower skin and lower
chord for any crack at the un-
repaired areas. (b)(c)
12,000 flight cy-
cles.
-CONDITION 3 ACTION 2
(OPTION 2):
Repeat internal detailed in-
spection of the center wing
box, STA 663.75 rear spar,
lower skin and lower chord
for any crack at the unre-
paired areas. (a)(b)
-Within 12,000 flight cycles after
the most recent OPTION 2 inspec-
tion was done.
CONDITION 4 (OPTION 1):
Do an external surface High
Frequency Eddy Current
(HFEC) inspection and ultra-
sonic inspection of the center
wing box, STA 663.75 rear
spar, lower skin and lower
chord for any crack. (b)(c)
CONDITION 4: NO
CRACK FOUND DUR-
ING THE INTERNAL
INSPECTION.
12,000 flight cy-
cles.
-CONDITION 4 (OPTION 2):
Repeat internal detailed in-
spection of the center wing
box, STA 663.75 rear spar,
lower skin and lower chord
for any crack. (b)(a)
(a) After the accomplishment of this OPTION, it is acceptable to change the repeat action from this OPTION
to any other OPTION under this CONDITION.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 01, 2020
737-57A1348 RB
12 of 28
REQUIREMENTS BULLETIN 737-57A1348
ALERTALERT

### Page 13

Group 2:
Table 1: External or Internal Inspection of the Center Wing Box, Station (STA) 663.75 Rear Spar, Lower
Skin and Lower Chord
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
(b) It is not required to do the inspection in areas where a repair covers the affected inspection area if the
repair meets the conditions that follow:
1. The repair is the corrective action to the crack condition identified in Requirements Bulletin 737-
57A1348 RB and installed after the original issue date of Requirements Bulletin 737-57A1348
RB.
2. The installed repair was approved by the Boeing Organization Designation Authorization (ODA)
via a FAA Form 8100-9.
(c) Refer to the applicable CONDITION for further ACTIONS.
4. APPROVAL
This Requirements Bulletin was examined by the Federal Aviation Administration (FAA). The changes
specified in this document comply with the applicable regulations and are FAA approved, as well as European
Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved
airplanes listed in the service bulletin effectivity.This document and its approval were based on the airplane
in its original Boeing delivery configuration or as modified by other Boeing changes.
If an airplane has a non-Boeing modification or repair that affects a component or system also affected by
this Requirements Bulletin, the operator is responsible for obtaining appropriate regulatory agency approval
before incorporating this Requirements Bulletin.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 01, 2020
737-57A1348 RB
13 of 28
REQUIREMENTS BULLETIN 737-57A1348
ALERTALERT

### Page 14

Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 01, 2020
737-57A1348 RB
14 of 28
REQUIREMENTS BULLETIN 737-57A1348
ALERTALERT
BLANK PAGE

### Page 15

5.    ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL INFORMATION
NOTE: 1. This is an Enhanced Required for Compliance document. There will be a separate
Service Bulletin (SB) and a separate Requirements Bulletin (RB). If an RB is mandated
by an Airworthiness Directive (AD), then all applicable requirements specified in the
RB must be done. For the related SB, some locations are marked RC Start and RC
End to identify the requirements that are restated from the RB. For the related SB,
the areas between RC Start and RC End, including sub-steps and any figures
identified between RC Start and RC End, must be done to comply with the AD.
Therefore, an Alternative Method of Compliance (AMOC) is required for any deviations
to steps between RC Start and RC End, including substeps and identified figures.
For the related SB, the steps not between RC Start and RC End may be deviated
from using accepted methods in accordance with the operator's maintenance or
inspection program without obtaining approval of an AMOC; this is provided that the
steps between RC Start and RC End, including sub-steps and identified figures, can
still be done as specified, and the airplane can be put back in an airworthy condition.
Figures not required for compliance are omitted from the RB.
2. This is an Enhanced Required for Compliance document. The Boeing processes
used to create the Service Bulletin (SB) and the Requirements Bulletin (RB) ensure
that the information between "RC Start" and "RC End" in the SB are identical to the
information in the same sections (Compliance, Work Instructions...) of the RB which
the SB refers to as the related document.
3. The compliance times for the actions in WORK INSTRUCTIONS are in Compliance.
4. Boeing Service Letter 737-SL-51-042, Damage Reporting and Repair Plan/Design
Guidelines, is an acceptable procedure to request information from Boeing for
additional structural repair instructions.The Service Letter describes what information
must be provided to Boeing before a structural repair can be provided.
5. Unless shown differently, these dimensions and tolerances are used:
– Linear dimensions are in inches
– Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus
or minus 0.03 inch
– Tolerance on rivet and bolt edge margin is plus or minus 0.05 inch
– Angular tolerance is plus or minus 2 degrees
– Hole dimensions for standard solid rivets and fasteners are in Structural Repair
Manual (SRM) Chapter 51
– Torque Values:
— Values for structural fasteners are given in 737 Structural Repair Manual,
Chapter 51.
— Values for airframe maintenance tasks are included in Chapter 20 of 737
Aircraft Maintenance Manual (AMM).
— Values for electrical maintenance tasks are included in Chapter 20 of
Standard Wiring Practices Manual (SWPM).
— Values for engine maintenance tasks are included in Chapter 70 of 737
Aircraft Maintenance Manual (AMM).
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 01, 2020
737-57A1348 RB
15 of 28
REQUIREMENTS BULLETIN 737-57A1348
ALERTALERT

### Page 16

— Non-standard torque values for maintenance tasks are included in the
applicable installation step.
6. These work instructions refer to procedures included in other Boeing documents.
When the words "refer to" are used and the operator has an accepted alternative
procedure, the accepted alternative procedure can be used. When the words "in
accordance with" are included in the instruction, the procedure in the Boeing document
must be used.
7. Where the work instructions include installation of a kept part, a new or serviceable
part with the same part number can be installed as an alternative to the kept part.
8. A Detailed Inspection is defined as: An intensive examination of a specific item,
installation or assembly to detect damage, failure or irregularity. This could include
tactile assessment in which a component or assembly can be checked for
tightness/security. Available lighting is normally supplemented with a direct source
of good lighting at an intensity deemed appropriate. Inspection aids such as mirrors
and magnifying lenses may be necessary. Surface cleaning and elaborate access
procedures may be required.
9. If it is necessary to remove more parts for access, you can remove those parts. If
you can get access without removing identified parts, it is not necessary to remove
all of the identified parts. Jacking and shoring limitations must be observed.
10. When more than one OPTION is given for a CONDITION, do only one of the OPTION
numbers. When more than one ACTION is given for a CONDITION or an OPTION,
do all of the ACTION numbers for that CONDITION or OPTION.
B. WORK INSTRUCTIONS
Actions Required for Compliance
1. Requirements.
Group 1:
Boeing endorses the FAA rules related to Limit of Validity (LOV) and recommends immediate and
permanent removal from service of any airplanes upon reaching the LOV, whether or not it is
operated under FAA jurisdiction. As such, Boeing no longer provides maintenance instructions for
airplanes that have accumulated flight cycles beyond the LOV. Airplanes in Group 1 (line numbers
1-291) have accumulated flight cycles beyond the LOV of the maintenance program. 14 CFR
121.1115 and 129.115 prohibit operation of an airplane beyond its LOV.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 01, 2020
737-57A1348 RB
16 of 28
REQUIREMENTS BULLETIN 737-57A1348
ALERTALERT

### Page 17

Group 2:
Table 1: External or Internal Inspection of the Center Wing Box, Station (STA) 663.75 Rear Spar, Lower
Skin and Lower Chord
Refer to the listed proce-
dures in SB 737-57A1348
Original Issue or later ap-
proved revisions as an ac-
cepted procedure
Method of ComplianceActionCondition
Do PART 1: GET ACCESS
FOR EXTERNAL INSPEC-
TION.
-OPTION 1:
Do an external surface High
Frequency Eddy Current
(HFEC) inspection and ultra-
sonic inspection of the center
wing box, STA 663.75 rear
spar, lower skin and lower
chord for any crack.
All airplanes.
-FIGURE 1
Do PART 2: GET ACCESS
FOR INTERNAL INSPEC-
TION.
-OPTION 2:
Do an internal detailed inspec-
tion of the center wing box,
STA 663.75 rear spar, lower
skin and lower chord for any
crack.
-FIGURE 2
--CONDITION 1 (ACTION 1):CONDITION 1: ANY
CRACK FOUND DUR-
ING THE EXTERNAL
INSPECTION.
Contact The Boeing Compa-
ny for repair instructions and
do the repair.
Do PART 3: CLOSE AC-
CESS FOR EXTERNAL IN-
SPECTION.
--
Do PART 1: GET ACCESS
FOR EXTERNAL INSPEC-
TION.
-CONDITION 1 (ACTION 2)
(OPTION 1):
Repeat external surface High
Frequency Eddy Current
(HFEC) inspection and ultra-
sonic inspection of the center
wing box, STA 663.75 rear
spar, lower skin and lower
chord for any crack at unre-
paired areas. (a)(b)
-FIGURE 1
Do PART 2: GET ACCESS
FOR INTERNAL INSPEC-
TION.
-CONDITION 1 (ACTION 2)
(OPTION 2):
Do an internal detailed inspec-
tion of the center wing box,
STA 663.75 rear spar, lower
skin and lower chord for any
crack at unrepaired areas.
(b)(c)
-FIGURE 2
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 01, 2020
737-57A1348 RB
17 of 28
REQUIREMENTS BULLETIN 737-57A1348
ALERTALERT

### Page 18

Group 2:
Table 1: External or Internal Inspection of the Center Wing Box, Station (STA) 663.75 Rear Spar, Lower
Skin and Lower Chord
Refer to the listed proce-
dures in SB 737-57A1348
Original Issue or later ap-
proved revisions as an ac-
cepted procedure
Method of ComplianceActionCondition
Do PART 3: CLOSE AC-
CESS FOR EXTERNAL IN-
SPECTION.
-CONDITION 2 (OPTION 1):
Repeat external surface High
Frequency Eddy Current
(HFEC) inspection and ultra-
sonic inspection of the center
wing box, STA 663.75 rear
spar, lower skin and lower
chord for any crack. (a)(b)
CONDITION 2: NO
CRACK FOUND DUR-
ING EXTERNAL IN-
SPECTION. Do PART 1: GET ACCESS
FOR EXTERNAL INSPEC-
TION.
-
-FIGURE 1
Do PART 2: GET ACCESS
FOR INTERNAL INSPEC-
TION.
-CONDITION 2 (OPTION 2):
Do an internal detailed inspec-
tion of the center wing box,
STA 663.75 rear spar, lower
skin and lower chord for any
crack. (b)(c)
-FIGURE 2
--CONDITION 3 (ACTION 1):CONDITION 3: ANY
CRACK FOUND DUR-
ING THE INTERNAL
INSPECTION.
Contact The Boeing Compa-
ny for repair instructions and
do the repair.
Do PART 4: CLOSE AC-
CESS FOR INTERNAL IN-
SPECTION.
-
Do PART 1: GET ACCESS
FOR EXTERNAL INSPEC-
TION.
-CONDITION 3 (ACTION 2)
(OPTION 1):
Do an external surface High
Frequency Eddy Current
(HFEC) inspection and ultra-
sonic inspection of the center
wing box, STA 663.75 rear
spar, lower skin and lower
chord for any crack at unre-
paired areas. (b)(c)
-FIGURE 1
Do PART 2: GET ACCESS
FOR INTERNAL INSPEC-
TION.
-CONDITION 3 (ACTION 2)
(OPTION 2):
Repeat internal detailed in-
spection of the center wing
box, STA 663.75 rear spar,
lower skin and lower chord
for any crack at unrepaired
areas. (a)(b)
-FIGURE 2
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 01, 2020
737-57A1348 RB
18 of 28
REQUIREMENTS BULLETIN 737-57A1348
ALERTALERT

### Page 19

Group 2:
Table 1: External or Internal Inspection of the Center Wing Box, Station (STA) 663.75 Rear Spar, Lower
Skin and Lower Chord
Refer to the listed proce-
dures in SB 737-57A1348
Original Issue or later ap-
proved revisions as an ac-
cepted procedure
Method of ComplianceActionCondition
Do PART 4: CLOSE AC-
CESS FOR INTERNAL IN-
SPECTION.
-CONDITION 4 (OPTION 1):
Do an external surface High
Frequency Eddy Current
(HFEC) inspection and ultra-
sonic inspection of the center
wing box, STA 663.75 rear
spar, lower skin and lower
chord for any crack. (b)(c)
CONDITION 4: NO
CRACK FOUND DUR-
ING THE INTERNAL
INSPECTION. Do PART 1: GET ACCESS
FOR EXTERNAL INSPEC-
TION.
-
-FIGURE 1
Do PART 2: GET ACCESS
FOR INTERNAL INSPEC-
TION.
-CONDITION 4 (OPTION 2):
Repeat internal detailed in-
spection of the center wing
box, STA 663.75 rear spar,
lower skin and lower chord
for any crack. (a)(b)
-FIGURE 2
(a) After the accomplishment of this OPTION, it is acceptable to change the repeat action from this OPTION
to any other OPTION under this CONDITION.
(b) It is not required to do the inspection in areas where a repair covers the affected inspection area if the
repair meets the conditions that follow:
1. The repair is the corrective action to the crack condition identified in Requirements Bulletin 737-
57A1348 RB and installed after the original issue date of Requirements Bulletin 737-57A1348
RB.
2. The installed repair was approved by the Boeing Organization Designation Authorization (ODA)
via a FAA Form 8100-9.
(c) Refer to the applicable CONDITION for further ACTIONS.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 01, 2020
737-57A1348 RB
19 of 28
REQUIREMENTS BULLETIN 737-57A1348
ALERTALERT

### Page 20 (OCR)

REQUIREMENTS BULLETIN 737-57A1348
ALERT  ALERT
This Figure applies only to: Group 2.
STA
663.75
STA
663.75
RBL
24.92
RBL
31.83
BL-0
RBL
LBL  6.15
LBL  6.15
24.92
LBL
31.83
STA
663.75
2932777
FIGURE 1: CENTER WING BOX - STA 663.75 REAR SPAR, LOWER SKIN AND LOWER CHORD - EXTERNAL
SURFACE HFEC AND ULTRASONIC INSPECTION
(SHEET 1 OF 4)
Original Issue: June 01, 2020
Export Controlled ECCN: 9E991  737-57A1348 RB
Copyright © Unpublished
Work - See page 1 for details.  20 of 28

### Page 21 (OCR)

REQUIREMENTS BULLETIN 737-57A1348
ALERT  ALERT
LBL  LBL  LBL
31.83  24.92  REAR SPAR WEB  LOWER CHORD  6.15  BL-O
LOWER SKIN
INBD
VIEW LOOKING FORWARD
BL-0  6.15  RBL  LOWER CHORD  REAR SPAR WEB  24.92  RBL  31.83  RBL
LOWER SKIN
INBD
VIEW LOOKING FORWARD
HFEC INSPECTION AREA
ULTRASONIC INSPECTION AREA  2932778
FIGURE 1: CENTER WING BOX - STA 663.75 REAR SPAR, LOWER SKIN AND LOWER CHORD - EXTERNAL
SURFACE HFEC AND ULTRASONIC INSPECTION
(SHEET 2 OF 4)
Original Issue: June 01, 2020
Export Controlled ECCN: 9E991  737-57A1348 RB
Copyright © Unpublished
Work - See page 1 for details.  21 of 28

### Page 22 (OCR)

REQUIREMENTS BULLETIN 737-57A1348
ALERT  ALERT
STA
STA  663.75
663.75  REAR SPAR WEB
REAR SPAR WEB
LOWER CHORD
LOWER CHORD
(TYPICAL)
LOWER SKIN
STIFFENER
LOWER SKIN
INSPECTION BETWEEN STIFFENERS  INSPECTION AT A STIFFENER
(TYPICAL)  (TYPICAL)
A-A  B-B
LOWER SKIN
LOWER CHORD
- TYPICAL CRACK
TYPICAL CRACK ~
STA
REAR SPAR WEB  663.75
BL-O  RBL
6.15
HFEC INSPECTION AREA  VIEW LOOKING DOWN
ULTRASONIC INSPECTION  C-C  2932779
AREA
FIGURE 1: CENTER WING BOX - STA 663.75 REAR SPAR, LOWER SKIN AND LOWER CHORD - EXTERNAL
SURFACE HFEC AND ULTRASONIC INSPECTION
(SHEET 3 OF 4)
Original Issue: June 01, 2020
Export Controlled ECCN: 9E991  737-57A1348 RB
Copyright © Unpublished
Work - See page 1 for details.  22 of 28

### Page 23

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
More DataQtyIdentificationNameTaskStep
(a)1-LOWER SKINInspect1
(a)1-LOWER CHORDInspect
(b)1-LOWER SKINInspect2
(b)1-LOWER CHORDInspect
(a) Do an external surface HFEC inspection of the center wing box rear spar, lower skin and lower chord for
any crack. Inspect the lower skin and lower chord in accordance with 737 NDT Manual Part 6, 51-00-00,
Procedure 4 or Procedure 23.
(b) Do an external ultrasonic inspection of the center wing box rear spar, lower skin and lower chord for any
crack. Inspect from both sides of the stiffener in accordance with 737 NDT Manual Part 4, 57-10-21.
FIGURE 1: CENTER WING BOX - STA 663.75 REAR SPAR, LOWER SKIN AND LOWER CHORD - EXTERNAL
SURFACE HFEC AND ULTRASONIC INSPECTION
(SHEET 4 OF 4)
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 01, 2020
737-57A1348 RB
23 of 28
REQUIREMENTS BULLETIN 737-57A1348
ALERTALERT

### Page 24 (OCR)

REQUIREMENTS BULLETIN 737-57A1348
ALERT  ALERT
This Figure applies only to: Group 2.
STA
663.75
STA
REAR SPAR WEB  663.75
24-92
31.53
BL-O
6.95
24-92  18.95
RBL
31.83
LOWER SKIN
LOWER SKIN CUT
AWAY FOR CLARITY
LOWER CHORD  2932780
FIGURE 2: CENTER WING BOX - STA 663.75 REAR SPAR, LOWER SKIN AND LOWER CHORD - INTERNAL
DETAILED INSPECTION
(SHEET 1 OF 5)
Original Issue: June 01, 2020
Export Controlled ECCN: 9E991  737-57A1348 RB
Copyright © Unpublished
Work - See page 1 for details.  24 of 28

### Page 25 (OCR)

REQUIREMENTS BULLETIN 737-57A1348
ALERT  ALERT
LBL  LBL  LBL
BL-O  6.15  LOWER CHORD  24.92  31.83
REAR SPAR WEB
378617
INBD  LOWER SKIN
VIEW LOOKING AFT
RBL  RBL  RBL
31.83  24.92  LOWER CHORD  6.15  BL-O
REAR SPAR WEB
C *
INBD  LOWER SKIN
VIEW LOOKING AFT
DETAILED INSPECTION AREA  2932781
FIGURE 2: CENTER WING BOX - STA 663.75 REAR SPAR, LOWER SKIN AND LOWER CHORD - INTERNAL
DETAILED INSPECTION
(SHEET 2 OF 5)
Original Issue: June 01, 2020
Export Controlled ECCN: 9E991  737-57A1348 RB
Copyright © Unpublished
Work - See page 1 for details.  25 of 28

### Page 26 (OCR)

REQUIREMENTS BULLETIN 737-57A1348
ALERT  ALERT
TYPICAL
TYPICAL  CRACK
CRACK  LOWER CHORD
BL-O  LBL  LBL
31.83  41
++++++++
+++++++
+ +
++++
LOWER SKIN
VIEW LOOKING DOWN
A-A
LOWER CHORD  TYPICAL  CRACK  TYPICAL  CRACK
RBL  RBL  BL-O
41  31.83
++++
+*+++++  =++++++++  +++++
LOWER SKIN
VIEW LOOKING DOWN
B-B
DETAILED INSPECTION AREA  2932782
FIGURE 2: CENTER WING BOX - STA 663.75 REAR SPAR, LOWER SKIN AND LOWER CHORD - INTERNAL
DETAILED INSPECTION
(SHEET 3 OF 5)
Original Issue: June 01, 2020
Export Controlled ECCN: 9E991  737-57A1348 RB
Copyright © Unpublished
Work - See page 1 for details.  26 of 28

### Page 27 (OCR)

REQUIREMENTS BULLETIN 737-57A1348
ALERT  ALERT
STA
663.75
REAR SPAR WEB
OWER CHOR
TYPICAL
- 2.0
MAXIMUM
LOWER SKIN  FWD
C-C
TYPICAL
REAR SPAR WEB  CHORD CRACK
LOWER CHORD-
2.0 MAXIUUM
TYPICAL SKIN
LOWER SKIN  CRACK
VIEW LOOKING DOWN
VIl DETAILED INSPECTION AREA  2932783
FIGURE 2: CENTER WING BOX - STA 663.75 REAR SPAR, LOWER SKIN AND LOWER CHORD - INTERNAL
DETAILED INSPECTION
(SHEET 4 OF 5)
Original Issue: June 01, 2020
Export Controlled ECCN: 9E991  737-57A1348 RB
Copyright © Unpublished
Work - See page 1 for details.  27 of 28

### Page 28

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
More DataQtyIdentificationNameTaskStep
(a)--SEALANTRemove1
(b)1-LOWER SKINInspect2
(b)1-LOWER CHORDInspect
(c)-BMS 5-45FUEL TANK SEALANTApply3
(c)-BMS 5-168FAST CURE FUEL
TANK SEALANT
Apply
(a) Remove any sealant from the lower skin or lower chord inspection area. Refer to SOPM 20-30-03, or
737-100/200 SRM 51-80-01, or 737-300 SRM 51-80-01, or 737-400 SRM 51-80-01, or 737-500 SRM 51-
80-01 as an accepted procedure.
(b) Do an internal detailed inspection of the center wing box, STA 663.75 rear spar, lower skin and lower
chord from Left Buttock Line (LBL) 31.83 to Right Buttock Line (RBL) 31.83 for any crack.
(c) Apply BMS 5-45 or BMS 5-168 sealant to the lower skin and lower chord inspection area where sealant
was removed in accordance with 737-100/200 SRM 51-80-01, or 737-300 SRM 51-80-01, or 737-400
SRM 51-80-01, or 737-500 SRM 51-80-01.
FIGURE 2: CENTER WING BOX - STA 663.75 REAR SPAR, LOWER SKIN AND LOWER CHORD - INTERNAL
DETAILED INSPECTION
(SHEET 5 OF 5)
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 01, 2020
737-57A1348 RB
28 of 28
REQUIREMENTS BULLETIN 737-57A1348
ALERTALERT

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
