# Boeing Alert Requirements Bulletin 737-57A1350 RB: No revision named

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2020-1166; AD 2021-19-19 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Alert Requirements Bulletin 737-57A1350 RB](https://openairdocs.org/service-documents/boeing/737-57a1350-rb.md)
- Title as filed: RB-737-57A1350 RB
- Pages: 42
- PDF: https://openairdocs.org/files/sha256/1b/22/1b22aaf4c53f6b85c60063913b2a2d9f11da0074bff10feeb46e59cedd69a1c8
- Page: https://openairdocs.org/service-documents/boeing/737-57a1350-rb/file/1b22aaf4c53f

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Commercial 
Airplanes
737
Requirements Bulletin
ALERT
Number: 737-57A1350 RB
Original Issue: April 23, 2020
ATA System: 5741
SUBJECT: WINGS - Leading Edge Access Panels - Outboard Blowout Door - Detailed Inspection
Export of this technology is controlled under the United States Export Administration Regulations (EAR) (15
CFR 300-774). An export license may be required before it is used for development, production or use by foreign
persons from specific countries. The controller of this data has the individual responsibility to abide by all export
laws.
9E991ECCN:
Copyright © 2020 Boeing.
Unpublished Work. All Rights Reserved.
Treatment of this document and its content is governed by contract with Boeing. Rights to use this document
are licensed on a per aircraft basis and such rights may not be transferable. For more information, contact The
Boeing Company.
Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner,
BBJ, DC-8, DC-9, DC-10, KC-10, KC-46, KDC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8, Poseidon and
Boeing liveries are all trademarks owned by The Boeing Company; and no trademark license is granted in
connection with this document unless provided in writing by Boeing.
Original Issue: April 23, 2020
737-57A1350 RB
1 of 42
3.0

### Page 2

Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 23, 2020
737-57A1350 RB
2 of 42
REQUIREMENTS BULLETIN 737-57A1350
ALERTALERT
BLANK PAGE

### Page 3

Table of Contents
1. EFFECTIVITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
A. Airplanes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
B. Spares Affected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2. CONCURRENT REQUIREMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3. COMPLIANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4. APPROVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
5. ACCOMPLISHMENT INSTR UCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
A. General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
B. Work Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
FIGURE 1: LEFT WING - FLUID SEAL CONT ACT INSPECTION . . . . . . . . . . . . . . . . . . . . 13
FIGURE 2: LEFT WING - OUTBOARD BLOWOUT DOOR - DETAILED INSPECTION . . . . . . . . . 16
FIGURE 3: LEFT WING - SEALANT APPLICA TION . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
FIGURE 4: LEFT WING - OUTBOARD BLOWOUT DOOR - SEALANT APPLICATION . . . . . . . . . 22
FIGURE 5: RIGHT WING - FLUID SEAL CONT ACT INSPECTION . . . . . . . . . . . . . . . . . . . 28
FIGURE 6: RIGHT WING - OUTBOARD BLOWOUT DOOR - DETAILED INSPECTION . . . . . . . . 31
FIGURE 7: RIGHT WING - SEALANT APPLICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
FIGURE 8: RIGHT WING - OUTBOARD BLOWOUT DOOR - SEALANT APPLICATION . . . . . . . . 37
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 23, 2020
737-57A1350 RB
3 of 42
REQUIREMENTS BULLETIN 737-57A1350
ALERTALERT

### Page 4

Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 23, 2020
737-57A1350 RB
4 of 42
REQUIREMENTS BULLETIN 737-57A1350
ALERTALERT
BLANK PAGE

### Page 5

Commercial 
Airplanes
737
Requirements Bulletin
ALERT
Number: 737-57A1350 RB
Original Issue: April 23, 2020
ATA System: 5741
SUBJECT: WINGS - Leading Edge Access Panels - Outboard Blowout Door - Detailed Inspection
THIS DOCUMENT IS SENT TO THE OPERATORS OF RECORD OF THE AIRPLANES SHOWN IN
PARAGRAPH 1.A., EFFECTIVITY. IF AN AIRPLANE HAS BEEN LEASED OR SOLD, SEND THIS DOCUMENT
TO THE NEW OPERATOR. IF APPLICABLE SPARES HAVE BEEN SOLD, SEND THIS DOCUMENT TO THE
NEW OWNER. THIS IS AN ENHANCED REQUIRED FOR COMPLIANCE DOCUMENT. THE BOEING
PROCESSES USED TO CREATE THE SERVICE BULLETIN (SB) AND THE REQUIREMENTS BULLETIN
(RB) ENSURE THAT THE INFORMATION BETWEEN "RC START" AND "RC END" IN THE SB ARE IDENTICAL
TO THE INFORMATION IN THE SAME SECTIONS (COMPLIANCE, WORK INSTRUCTIONS…) OF THE RB
WHICH THE SB REFERS TO AS THE RELATED DOCUMENT.
1. Effectivity
A. Airplanes
This bulletin is applicable to 737-9 Airplane(s), line number(s) 6834, 6852, 6872, 6899, 6917, 6935,
7096, 7173, 7196, 7201, 7208, 7216, 7246, 7253, 7261, 7268, 7306, 7316, 7338, 7348, 7361,
7384, 7388, 7394, 7428 in 1 Group(s).
DESCRIPTIONCONFIGURATIONGROUP
737-9 Airplanes-1
Airplane Models:
737-9
GroupVariable Number
11D051 - 1D056
11D101 - 1D114
GroupVariable Number
11D251 - 1D253
11D401
GroupVariable Number
11D466
--
B. Spares Affected
None.
2. CONCURRENT REQUIREMENTS
None.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 23, 2020
737-57A1350 RB
5 of 42

### Page 6

3. COMPLIANCE
The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to
Requirements Bulletin 737-57A1350 RB. The Airworthiness Directive will make the compliance tasks and
times given in Requirements Bulletin 737-57A1350 RB mandatory.
Accomplish the required action(s), based on the applicable conditions in Tables 1 and 2, in accordance
with Accomplishment Instructions.
When more than one OPTION is given for a CONDITION, do only one of the OPTION numbers. When
more than one ACTION is given for a CONDITION or an OPTION, do all of the ACTION numbers for that
CONDITION or OPTION.
Table 1: Inspection of the Left Wing - Leading Edge - Outboard Blowout Door.
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
-Within 12 months
after the Original
Issue date of Re-
quirements Bulletin
737-57A1350 RB.
(ACTION 1): Do a fluid
seal contact inspection.
All Airplanes.
(ACTION 2): Do a de-
tailed inspection of the
blowout door, inboard
and outboard ends of the
hinge, for sealant.
--No further action is re-
quired for this condition.
CONDITION 1: CONTINU-
OUS CONTACT FOUND
DURING FLUID SEAL
CONTACT INSPECTION.
(a)
-Before further
flight.
Apply sealant to the
blowout door surround at
all locations aligned to
where continuous contact
was not found.
CONDITION 2: CONTINU-
OUS CONTACT NOT
FOUND DURING FLUID
SEAL CONTACT INSPEC-
TION. (a)
--No further action is re-
quired for this condition.
CONDITION 3: INBOARD
AND OUTBOARD ENDS
OF THE HINGE OF
BLOWOUT DOOR ARE
SEALED. (a)
-Before further
flight.
Apply sealant to the affect-
ed blowout door inboard
or outboard hinge area.
CONDITION 4: INBOARD
OR OUTBOARD ENDS OF
THE HINGE OF
BLOWOUT DOOR ARE
NOT SEALED. (a)
(a) More than one condition can be applicable to each airplane.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 23, 2020
737-57A1350 RB
6 of 42
REQUIREMENTS BULLETIN 737-57A1350
ALERTALERT

### Page 7

Table 2: Inspection of the Right Wing - Leading Edge - Outboard Blowout Door.
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
-Within 12 months
after the Original
Issue date of Re-
quirements Bulletin
737-57A1350 RB.
(ACTION 1): Do a fluid
seal contact inspection.
All Airplanes.
(ACTION 2): Do a de-
tailed inspection of the
blowout door, inboard
and outboard ends of the
hinge, for sealant.
--No further action is re-
quired for this condition.
CONDITION 5: CONTINU-
OUS CONTACT FOUND
DURING FLUID SEAL
CONTACT INSPECTION.
(a)
-Before further
flight.
Apply sealant to the
blowout door surround at
all locations aligned to
where continuous contact
was not found.
CONDITION 6: CONTINU-
OUS CONTACT NOT
FOUND DURING FLUID
SEAL CONTACT INSPEC-
TION. (a)
--No further action is re-
quired for this condition.
CONDITION 7: INBOARD
AND OUTBOARD ENDS
OF THE HINGE OF
BLOWOUT DOOR ARE
SEALED. (a)
-Before further
flight.
Apply sealant to the affect-
ed blowout door inboard
or outboard hinge area.
CONDITION 8: INBOARD
OR OUTBOARD ENDS OF
THE HINGE OF
BLOWOUT DOOR ARE
NOT SEALED. (a)
(a) More than one condition can be applicable to each airplane.
4. APPROVAL
This Requirements Bulletin was examined by the Federal Aviation Administration (FAA). The changes
specified in this document comply with the applicable regulations and are FAA approved, as well as European
Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved
airplanes listed in the service bulletin effectivity.This document and its approval were based on the airplane
in its original Boeing delivery configuration or as modified by other Boeing changes.
If an airplane has a non-Boeing modification or repair that affects a component or system also affected by
this Requirements Bulletin, the operator is responsible for obtaining appropriate regulatory agency approval
before incorporating this Requirements Bulletin.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 23, 2020
737-57A1350 RB
7 of 42
REQUIREMENTS BULLETIN 737-57A1350
ALERTALERT

### Page 8

Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 23, 2020
737-57A1350 RB
8 of 42
REQUIREMENTS BULLETIN 737-57A1350
ALERTALERT
BLANK PAGE

### Page 9

5.    ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL INFORMATION
NOTE: 1. This is an Enhanced Required for Compliance document. There will be a separate
Service Bulletin (SB) and a separate Requirements Bulletin (RB). If an RB is mandated
by an Airworthiness Directive (AD), then all applicable requirements specified in the
RB must be done. For the related SB, some locations are marked RC Start and RC
End to identify the requirements that are restated from the RB. For the related SB,
the areas between RC Start and RC End, including sub-steps and any figures
identified between RC Start and RC End, must be done to comply with the AD.
Therefore, an Alternative Method of Compliance (AMOC) is required for any deviations
to steps between RC Start and RC End, including substeps and identified figures.
For the related SB, the steps not between RC Start and RC End may be deviated
from using accepted methods in accordance with the operator's maintenance or
inspection program without obtaining approval of an AMOC; this is provided that the
steps between RC Start and RC End, including sub-steps and identified figures, can
still be done as specified, and the airplane can be put back in an airworthy condition.
Figures not required for compliance are omitted from the RB.
2. This is an Enhanced Required for Compliance document. The Boeing processes
used to create the Service Bulletin (SB) and the Requirements Bulletin (RB) ensure
that the information between "RC Start" and "RC End" in the SB are identical to the
information in the same sections (Compliance, Work Instructions...) of the RB which
the SB refers to as the related document.
3. The compliance times for the actions in WORK INSTRUCTIONS are in Compliance.
4. Unless shown differently, these dimensions and tolerances are used:
– Linear dimensions are in inches
– Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus
or minus 0.03 inch
– Tolerance on rivet and bolt edge margin is plus or minus 0.05 inch
– Angular tolerance is plus or minus 2 degrees
– Hole dimensions for standard solid rivets and fasteners are in Structural Repair
Manual (SRM) Chapter 51
– Torque Values:
— Values for structural fasteners are given in 737 Structural Repair Manual,
Chapter 51.
— Values for airframe maintenance tasks are included in Chapter 20 of 737
Aircraft Maintenance Manual (AMM).
— Values for electrical maintenance tasks are included in Chapter 20 of
Standard Wiring Practices Manual (SWPM).
— Values for engine maintenance tasks are included in Chapter 70 of 737
Aircraft Maintenance Manual (AMM).
— Non-standard torque values for maintenance tasks are included in the
applicable installation step.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 23, 2020
737-57A1350 RB
9 of 42
REQUIREMENTS BULLETIN 737-57A1350
ALERTALERT

### Page 10

5. These work instructions refer to procedures included in other Boeing documents.
When the words "refer to" are used and the operator has an accepted alternative
procedure, the accepted alternative procedure can be used. When the words "in
accordance with" are included in the instruction, the procedure in the Boeing document
must be used.
6. Where the work instructions include installation of a kept part, a new or serviceable
part with the same part number can be installed as an alternative to the kept part.
7. If it is necessary to remove more parts for access, you can remove those parts. If
you can get access without removing identified parts, it is not necessary to remove
all of the identified parts. Jacking and shoring limitations must be observed.
8. Use the approved fastener, process and material substitutions in accordance with
SRM Chapter 51.
9. A Detailed Inspection is defined as: An intensive examination of a specific item,
installation or assembly to detect damage, failure or irregularity. This could include
tactile assessment in which a component or assembly can be checked for
tightness/security. Available lighting is normally supplemented with a direct source
of good lighting at an intensity deemed appropriate. Inspection aids such as mirrors
and magnifying lenses may be necessary. Surface cleaning and elaborate access
procedures may be required.
10. When more than one OPTION is given for a CONDITION, do only one of the OPTION
numbers. When more than one ACTION is given for a CONDITION or an OPTION,
do all of the ACTION numbers for that CONDITION or OPTION.
B. WORK INSTRUCTIONS
1. Requirements
Table 1: Detailed Inspection of the Left Wing - Leading Edge - Outboard Blowout Door.
Refer to the listed
procedures in
737-57A1350 SB
Original Issue or
later approved re-
visions as an ac-
cepted proce-
dure.
Method of Compli-
ance
ActionCondition
PART 1: OPEN
ACCESS.
-(ACTION 1): Do a fluid
seal contact inspection.
All Airplanes.
-FIGURE 1
-FIGURE 2(ACTION 2): Do a de-
tailed inspection of the
blowout door, inboard
and outboard ends of the
hinge, for sealant.
PART 2: CLOSE
ACCESS.
-
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 23, 2020
737-57A1350 RB
10 of 42
REQUIREMENTS BULLETIN 737-57A1350
ALERTALERT

### Page 11

Table 1: Detailed Inspection of the Left Wing - Leading Edge - Outboard Blowout Door.
Refer to the listed
procedures in
737-57A1350 SB
Original Issue or
later approved re-
visions as an ac-
cepted proce-
dure.
Method of Compli-
ance
ActionCondition
--No further action is re-
quired for this condition.
CONDITION 1: CONTINU-
OUS CONTACT FOUND
DURING FLUID SEAL
CONTACT INSPEC-
TION.(a)
-FIGURE 3Apply sealant to the
blowout door surround at
all locations aligned to
where continuous contact
was not found.
CONDITION 2: CONTINU-
OUS CONTACT NOT
FOUND DURING FLUID
SEAL CONTACT INSPEC-
TION.(a)
--No further action is re-
quired for this condition.
CONDITION 3: INBOARD
AND OUTBOARD ENDS
OF THE HINGE OF
BLOWOUT DOOR ARE
SEALED.(a)
-FIGURE 4Apply sealant to the affect-
ed blowout door inboard
or outboard hinge area.
CONDITION 4: INBOARD
OR OUTBOARD ENDS OF
THE HINGE OF
BLOWOUT DOOR ARE
NOT SEALED.(a)
(a) More than one condition can be applicable to each airplane.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 23, 2020
737-57A1350 RB
11 of 42
REQUIREMENTS BULLETIN 737-57A1350
ALERTALERT

### Page 12

Table 2: Detailed Inspection of the Right Wing - Leading Edge - Outboard Blowout Door.
Refer to the listed
procedures in
737-57A1350 RB
Original Issue or
later approved re-
visions as an ac-
cepted proce-
dure.
Method of Compli-
ance
ActionCondition
PART 1: OPEN
ACCESS.
-(ACTION 1): Do a fluid
seal contact inspection.
All Airplanes.
-FIGURE 5
-FIGURE 6(ACTION 2): Do a de-
tailed inspection of the
blowout door, inboard
and outboard ends of the
hinge, for sealant.
PART 3: CLOSE
ACCESS.
-
--No further action is re-
quired for this condition.
CONDITION 5: CONTINU-
OUS CONTACT FOUND
DURING FLUID SEAL
CONTACT INSPEC-
TION.(a)
-FIGURE 7Apply sealant to the
blowout door surround at
all locations aligned to
where continuous contact
was not found.
CONDITION 6: CONTINU-
OUS CONTACT NOT
FOUND DURING FLUID
SEAL CONTACT INSPEC-
TION.(a)
--No further action is re-
quired for this condition.
CONDITION 7: INBOARD
AND OUTBOARD ENDS
OF THE HINGE OF
BLOWOUT DOOR ARE
SEALED.(a)
-FIGURE 8Apply sealant to the affect-
ed blowout door inboard
or outboard hinge area.
CONDITION 8: INBOARD
OR OUTBOARD ENDS OF
THE HINGE OF
BLOWOUT DOOR ARE
NOT SEALED.(a)
(a) More than one condition can be applicable to each airplane.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 23, 2020
737-57A1350 RB
12 of 42
REQUIREMENTS BULLETIN 737-57A1350
ALERTALERT

### Page 13 (OCR)

REQUIREMENTS BULLETIN 737-57A1350
ALERT  ALERT
STRAKELET
02450
BLOWOUT
DOOR
LOWER
SKIN PANEL
LEFT WINC
(VIEW LOOKING UP)
NBD
2927190
FIGURE 1: LEFT WING - FLUID SEAL CONTACT INSPECTION
(SHEET 1 OF 3)
Original Issue: April 23, 2020
Export Controlled ECCN: 9E991  737-57A1350 RB
Copyright © Unpublished
Work - See page 1 for details.  13 of 42

### Page 14

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for one side of the airplane.
More DataQtyIdentificationNameTaskStep
(a)1521ABBLOWOUT DOOROpen1
(b)1521ABBLOWOUT DOORClean2
(c)(d)-MET-L-CHEK (D70 OR
OPTIONAL D-100)
DEVELOPERApply3
(e)1521ABBLOWOUT DOORClose4
(a)1521ABBLOWOUT DOOROpen5
(f)--BLOWOUT DOOR
SURROUND
Inspect6
FIGURE 1: LEFT WING - FLUID SEAL CONTACT INSPECTION
(SHEET 2 OF 3)
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 23, 2020
737-57A1350 RB
14 of 42
REQUIREMENTS BULLETIN 737-57A1350
ALERTALERT

### Page 15

More DataQtyIdentificationNameTaskStep
(g)1521ABBLOWOUT DOORClean7
(g)1-BLOWOUT DOOR
SURROUND
Clean
(a) Open the blowout door. Refer to 737-7/8/8200/9/10 AMM 57-41-02 as an accepted procedure.
(b) Clean blowout door seal and blowout door surround of any dirt or debris.
(c) Apply developer along the blowout door surround common to blowout door seal contact area.
(d) Use bulk material and not the aerosol spray.
(e) Close and latch the blowout door. Refer to 737-7/8/8200/9/10 AMM 57-41-02 as an accepted procedure.
(f) Inspect the amount of developer transferred from the blowout door surround to the blowout door gasket.
Make sure that the developer contact on the blowout door gasket is continuous. There is no minimum
contact width required as long as contact exists.
(g) Remove developer from blowout door and blowout door surround.
FIGURE 1: LEFT WING - FLUID SEAL CONTACT INSPECTION
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 23, 2020
737-57A1350 RB
15 of 42
REQUIREMENTS BULLETIN 737-57A1350
ALERTALERT

### Page 16 (OCR)

REQUIREMENTS BULLETIN 737-57A1350
ALERT  ALERT
STRAKELET
•0.
BLOWOUT
DOOR
LOWER
SKIN PANEL
LEFT WING
BLOWOUT DOOR NO SEALANT PRESENT
(VIEW LOOKING UP)
2927186
FIGURE 2: LEFT WING - OUTBOARD BLOWOUT DOOR - DETAILED INSPECTION
(SHEET 1 OF 3)
Original Issue: April 23, 2020
Export Controlled ECCN: 9E991  737-57A1350 RB
Copyright © Unpublished
Work - See page 1 for details.  16 of 42

### Page 17 (OCR)

REQUIREMENTS BULLETIN 737-57A1350
ALERT  ALERT
BLOWOUT  BLOWOUT
STRAKELET  DOOR  DOOR  STRAKELET
INBOARD HINGE END  OUTBOARD HINGE END
(NO SEALANT APPLIED - BLOWOUT DOOR CLOSED)  (NO SEALANT APPLIED - BLOWOUT DOOR CLOSED)
STRAKELET SEAL  SEAL  STRAKELET
INBOARD HINGE END  OUTBOARD HINGE END
(NO SEALANT APPLIED - BLOWOUT DOOR NOT  (NO SEALANT APPLIED - BLOWOUT DOOR NOT
SHOWN FOR CLARITY)  SHOWN FOR CLARITY)
A SEALANT INSPECTION AREA
FIGURE 2: LEFT WING - OUTBOARD BLOWOUT DOOR - DETAILED INSPECTION
(SHEET 2 OF 3)
Original Issue: April 23, 2020
Export Controlled ECCN: 9E991  Copyright © Unpublished  737-57A1350 RB
Work - See page 1 for details.  17 of 42

### Page 18

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for one side of the airplane.
More DataQtyIdentificationNameTaskStep
(a)2-HINGE SLOT
SEALANT
Inspect1
(b)1521ABBLOWOUT DOOROpen2
(c)1-HINGE SLOT
SEALANT
Inspect3
(a) With the blowout door closed, do a detailed inspection of the area at the inboard and outboard ends of
the blowout door hinge for continuous sealant. All visible space at the ends of the hinge to the inboard
and outboard edges of the blowout door, and from the forward edge of the blowout door to the aft edge
of the strakelet skin must be continuously filled with sealant and faired to the external surface. If the
sealant applied to the internal and external surfaces are not sealed as described, then the space at the
inboard and outboard end of the hinge is not sealed.
(b) Open the blowout door. Refer to 737-7/8/8200/9/10 AMM 57-41-02 as an accepted procedure.
(c) With the blowout door open, do a detailed inspection of the hinge area at the inboard and outboard ends
of the blowout for continuous sealant along the seal. For the sealant applied to the internal surface to be
continuous, it must be formed to match the profile of the edges of the blowout door and hinge, with no
surface defects, and it must be bonded to the seal and the blowout door surround. If the sealant applied
to the internal and external surfaces are not sealed as described, then the space at the inboard and out-
board end of the hinge is not sealed.
FIGURE 2: LEFT WING - OUTBOARD BLOWOUT DOOR - DETAILED INSPECTION
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 23, 2020
737-57A1350 RB
18 of 42
REQUIREMENTS BULLETIN 737-57A1350
ALERTALERT

### Page 19 (OCR)

REQUIREMENTS BULLETIN 737-57A1350
ALERT  ALERT
STRAKELET
D34€
BLOWOUT
DOOR
LOWER
SKIN PANEL
LEFT WINC
(VIEW LOOKING UP)
NBD
2927177
FIGURE 3: LEFT WING - SEALANT APPLICATION
(SHEET 1 OF 3)
Original Issue: April 23, 2020
Export Controlled ECCN: 9E991  737-57A1350 RB
Copyright © Unpublished
Work - See page 1 for details.  19 of 42

### Page 20

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for one side of the airplane.
More DataQtyIdentificationNameTaskStep
(a)1521ABBLOWOUT DOOROpen1
---BLOWOUT DOOR
SURROUND
Clean2
(b)--BLOWOUT DOOR
SURROUND
Prepare
(c)--BLOWOUT DOOR
SURROUND
Clean3
(c)-521ABBLOWOUT DOORClean
(d)-FREKOTE 710-NCRELEASE AGENTApply4
(e)-BMS 5-45 B-1/2SEALANTApply5
FIGURE 3: LEFT WING - SEALANT APPLICATION
(SHEET 2 OF 3)
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 23, 2020
737-57A1350 RB
20 of 42
REQUIREMENTS BULLETIN 737-57A1350
ALERTALERT

### Page 21

More DataQtyIdentificationNameTaskStep
(f)1521ABBLOWOUT DOORClose6
(g)(h)(i)-BMS 5-45 B-1/2SEALANTClean7
(a) Open the blowout door. Refer to 737-7/8/8200/9/10 AMM 57-41-02 as an accepted procedure.
(b) Abrade any existing cured sealant with 180 grit or finer sandpaper to remove all surface gloss where de-
veloper contact is not continuous.
(c) Clean and prepare surfaces for sealant and release agent application at existing seal location on the
blowout door and blowout door surround. Refer to SOPM 20-50-19 as an accepted procedure.
(d) Apply two coats of release agent to the blowout door surface in contact with the blowout door surround,
allowing 5-10 minutes after each application to cure. Extend the release agent as needed to ease the
removal of sealant squeeze out. Do not apply to the blowout door surround.
(e) Apply sealant BMS5-45, Class B-1/2 or optional BMS 5-182, Type 1, Class B-1/2, or PR-1826 primer and
sealant to the areas of the blowout door surround where contact was not made between the blowout door
and blowout door surround. Refer to SOPM 20-50-19 as an accepted procedure.
(f) Close and latch the blowout door. Refer to 737-7/8/8200/9/10 AMM 57-41-02 as an accepted procedure.
Make sure 20 minutes has passed after the second application of the release agent before the closing of
the blowout door.
(g) While the form-in-place gasket sealant is still wet, remove the excess sealant between the edges of both
door and the blowout door surround, fair the sealant at support structure edges and wait for the sealant
to dry.
(h) After the sealant dries, open and close the blowout door to break it free from the sealant. After cycling
the door, the door should open without assistance. Make sure that the sealant bonds to the blowout door
surround and not the blowout door. Remove any sealant that has adhered to the blowout door. Refer to
SOPM 20-50-19 as an accepted procedure. Petrolatum or Krytox may be applied to the door as a post
cure lubricant. If petrolatum is applied to the door after the sealant has cured, it must be wiped off with a
lint-free rag leaving behind a thin film. If Krytox is used, it does not have to be wiped off.
(i) Make sure sealant has formed along the existing seal on the blowout door surround at the areas where
contact was not made.
FIGURE 3: LEFT WING - SEALANT APPLICATION
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 23, 2020
737-57A1350 RB
21 of 42
REQUIREMENTS BULLETIN 737-57A1350
ALERTALERT

### Page 22 (OCR)

REQUIREMENTS BULLETIN 737-57A1350
ALERT  ALERT
STRAKELET
BLOWOUT
DOOR
LOWER
SKIN PANEL
LEFT WING
BLOWOUT DOOR SEALANT PRESENT
(VIEW LOOKING UP)
2927173
FIGURE 4: LEFT WING - OUTBOARD BLOWOUT DOOR - SEALANT APPLICATION
(SHEET 1 OF 6)
Original Issue: April 23, 2020
Export Controlled ECCN: 9E991  737-57A1350 RB
Copyright © Unpublished
Work - See page 1 for details.  22 of 42

### Page 23 (OCR)

REQUIREMENTS BULLETIN 737-57A1350
ALERT  ALERT
BLOWOUT
DOOR
STRAKELET
BLOWOUT
DOOR
SURROUND
BLOWOUT PANEL
(INBOARD HINGE AREA PREPARATION)
BLOWOUT
DOOR  2) BLOWOUT
DOOR
STRAKELET  SURROUND
BLOWOUT PANEL
(OUTBOARD HINGE AREA PREPARATION)
SEALANT APPLICATION AREA  2927172
FIGURE 4: LEFT WING - OUTBOARD BLOWOUT DOOR - SEALANT APPLICATION
(SHEET 2 OF 6)
Original Issue: April 23, 2020
Export Controlled ECCN: 9E991  737-57A1350 RB
Copyright © Unpublished
Work - See page 1 for details.  23 of 42

### Page 24 (OCR)

REQUIREMENTS BULLETIN 737-57A1350
ALERT  ALERT
2 4  STRAKELET
SEAL
INBOARD HINGE END
SEALANT PENETRATION
(BLOWOUT DOOR NOT SHOWN FOR CLARITY)
STRAKELET
SEAL
OUTBOARD HINGE END
SEALANT PENETRATION
(BLOWOUT DOOR NOT SHOWN FOR CLARITY)
SEALANT APPLICATION AREA  2927171
FIGURE 4: LEFT WING - OUTBOARD BLOWOUT DOOR - SEALANT APPLICATION
(SHEET 3 OF 6)
Original Issue: April 23, 2020
Export Controlled ECCN: 9E991  737-57A1350 RB
Copyright © Unpublished
Work - See page 1 for details.  24 of 42

### Page 25 (OCR)

REQUIREMENTS BULLETIN 737-57A1350
ALERT  ALERT
SEALANT  BLOWOUT
DOOR
STRAKELET
D
LOWON PANE
INBOARD HINGE AREA SEALANT APPLICATION
BLOWOUT
DOOR  SEALANT
STRAKELET
BLOWOUT PANEL
(OUTBOARD HINGE AREA SEALANT APPLICATION)
SEALANT APPLICATION AREA  2927170
FIGURE 4: LEFT WING - OUTBOARD BLOWOUT DOOR - SEALANT APPLICATION
(SHEET 4 OF 6)
Original Issue: April 23, 2020
Export Controlled ECCN: 9E991  737-57A1350 RB
Copyright © Unpublished
Work - See page 1 for details.  25 of 42

### Page 26

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for one side of the airplane.
More DataQtyIdentificationNameTaskStep
(a)1521ABBLOWOUT DOOROpen1
(b)-521ABBLOWOUT DOORClean2
(b)--BLOWOUT DOOR
SURROUND
Clean
(c)-FREKOTE 710-NCRELEASE AGENTApply3
(d)-BMS 5-45 B-1/2SEALANTApply4
(e)1521ABBLOWOUT DOORClose5
(f)-BMS 5-45 B-1/2SEALANTApply6
(g)(h)-BMS 5-45 B-1/2SEALANTClean7
(a) Open the blowout door. Refer to 737-7/8/8200/9/10 AMM 57-41-02 as an accepted procedure.
(b) Clean and prepare surfaces for sealant and release agent application, at both ends of the blowout door
hinge, blowout door surround and blowout door. Refer to SOPM 20-50-19 as an accepted procedure.
(c) Apply two coats of release agent to the blowout door inner surface and edges that will be in contact with
wet sealant and blowout door surround, allowing 5-10 minutes after each application to cure. Allow 20
minutes after the second application before closing the door. Extend the release agent as needed to ease
the removal of sealant squeeze out. As an option you may apply the Frekote to the entire side of the door
panel. Do not apply to the door surround structure.
(d) Apply sealant BMS5-45, Class B-1/2 or optional BMS 5-182, Type 1, Class B-1/2, or PR-1826 primer and
sealant to the space between the blowout door and the blowout door surround. Refer to SOPM 20-50-19
as an accepted procedure. Make sure sealant is backfilled into the recesses in the space before topping
off. Apply enough sealant so that excess will squeeze out and make sure the space is completely filled.
(e) Close and latch the blowout door. Refer to 737-7/8/8200/9/10 AMM 57-41-02 as an accepted procedure.
(f) While the sealant is still wet, remove the squeeze-out sealant between the edges of both blowout door
and the blowout door surround, except in the area of the intended filled space shown in view F and G.
Fair the sealant in the area with the surrounding external surfaces so that the faired sealant has filled the
space completely, and wait for the sealant to dry.
(g) After the sealant dries, open and close the blowout door to break it free from the sealant. After cycling
the door, the door should open without assistance. Make sure that the sealant bonds to the door structure
and not the blowout door. Refer to SOPM 20-50-19 as an accepted procedure. Krytox or Petrolatum may
be applied to the door as a post-cure lubricant. If petrolatum is applied to the door after the sealant has
cured, it must be wiped off with a lint-free rag leaving behind a thin film. If Krytox is used, it does not have
to be wiped off.
FIGURE 4: LEFT WING - OUTBOARD BLOWOUT DOOR - SEALANT APPLICATION
(SHEET 5 OF 6)
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 23, 2020
737-57A1350 RB
26 of 42
REQUIREMENTS BULLETIN 737-57A1350
ALERTALERT

### Page 27

More DataQtyIdentificationNameTaskStep
(h) With the blowout door open, make sure the sealant has formed to continuously match the profile of the
edges of the blowout door and hinge half, with no surface defects, and make sure it is bonded to the bulb
seal and the surround structure inboard and outboard of the bulb seal. With the blowout door closed,
make sure all visible space inboard and outboard of the ends of the hinge to the inboard and outboard
edges of the door, and from the forward edge of the door to the aft edge of the strakelet skin are continu-
ously filled with sealant and faired to the external surface.
FIGURE 4: LEFT WING - OUTBOARD BLOWOUT DOOR - SEALANT APPLICATION
(SHEET 6 OF 6)
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 23, 2020
737-57A1350 RB
27 of 42
REQUIREMENTS BULLETIN 737-57A1350
ALERTALERT

### Page 28 (OCR)

REQUIREMENTS BULLETIN 737-57A1350
ALERT  ALERT
STRAKELET
245+
BLOWOUT
DOOR
LOWER
SKIN PANEL
RIGHT WING
(VIEW LOOKING UP)  INBD
2927191
FIGURE 5: RIGHT WING - FLUID SEAL CONTACT INSPECTION
(SHEET 1 OF 3)
Original Issue: April 23, 2020
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.  28 of 42

### Page 29 (OCR)

REQUIREMENTS BULLETIN 737-57A1350
ALERT  ALERT
STRAKELET
FUEL SHUTOFF  BLOWOUT DOOR 3
O:0
LOWER
SKIN PANEL
RIGHT WING
(VIEW LOOKING UP  •
BLOWOUT DOOR NOT SHOWN FOR CLARITY
INBD
INSPECTION AREA
The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for one side of the airplane.
Step  Task  Name  Identification  Qty  More Data
Open  BLOWOUT DOOR  621AB  1  (a)
2  Clean  BLOWOUT DOOR  621AB  1  (b)
З  Apply  DEVELOPER  MET-L-CHEK (D70 OR  (c)(d)
OPTIONAL D-100)
4  Close  BLOWOUT DOOR  621AB  1  (e)
5  Open  BLOWOUT DOOR  621AB  1  (a)
6  Inspect  BLOWOUT DOOR  (†)
SURROUND
FIGURE 5: RIGHT WING - FLUID SEAL CONTACT INSPECTION
(SHEET 2 OF 3)
Original Issue: April 23, 2020
Export Controlled ECCN: 9E991  737-57A1350 RB
Copyright © Unpublished
Work - See page 1 for details.  29 of 42

### Page 30

More DataQtyIdentificationNameTaskStep
(g)1621ABBLOWOUT DOORClean7
(g)1-BLOWOUT DOOR
SURROUND
Clean
(a) Open the blowout door. Refer to 737-7/8/8200/9/10 AMM 57-41-02 as an accepted procedure.
(b) Clean blowout door seal and blowout door surround of any dirt or debris.
(c) Apply developer along the blowout door surround common to blowout door seal contact area.
(d) Use bulk material and not the aerosol spray.
(e) Close and latch the blowout door. Refer to 737-7/8/8200/9/10 AMM 57-41-02 as an accepted procedure.
(f) Inspect the amount of developer transferred from the blowout door surround to the blowout door gasket.
Make sure that the developer contact on the blowout door gasket is continuous. There is no minimum
contact width required as long as contact exists.
(g) Remove developer from blowout door and blowout door surround.
FIGURE 5: RIGHT WING - FLUID SEAL CONTACT INSPECTION
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 23, 2020
737-57A1350 RB
30 of 42
REQUIREMENTS BULLETIN 737-57A1350
ALERTALERT

### Page 31 (OCR)

REQUIREMENTS BULLETIN 737-57A1350
ALERT  ALERT
STRAKELET
(г)
BLOWOUT
DOOR
LOWER
SKIN PANEL
RIGHT WING
BLOWOUT DOOR NO SEALANT PRESENT
(VIEW LOOKING UP)
INBD
FIGURE 6: RIGHT WING - OUTBOARD BLOWOUT DOOR - DETAILED INSPECTION
(SHEET 1 OF 3)
Original Issue: April 23, 2020
Export Controlled ECCN: 9E991  Copyright © Unpublished  737-57A1350 RB
Work - See page 1 for details.  31 of 42

### Page 32 (OCR)

REQUIREMENTS BULLETIN 737-57A1350
ALERT  ALERT
BLOWOUT  BLOWOUT
STRAKELET  DOOR  DOOR  STRAKELET
OUTBOARD HINGE END  INBOARD HINGE END
(NO SEALANT APPLIED - BLOWOUT DOOR CLOSED)  (NO SEALANT APPLIED - BLOWOUT DOOR CLOSED)
STRAKELET
STRAKELET  SEAL  SEAL
OUTBOARD HINGE END
(NO SEALANT APPLIED - BLOWOUT DOOR
NOT SHOWN FOR CLARITY)
SEALANT INSPECTION AREA
INBOARD HINGE END
(NO SEALANT APPLIED - BLOWOUT DOOR
NOT SHOWN FOR CLARITY)
FIGURE 6: RIGHT WING - OUTBOARD BLOWOUT DOOR - DETAILED INSPECTION
(SHEET 2 OF 3)
Original Issue: April 23, 2020
Export Controlled ECCN: 9E991  737-57A1350 RB
Copyright © Unpublished
Work - See page 1 for details.  TO ZE

### Page 33

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for one side of the airplane.
More DataQtyIdentificationNameTaskStep
(a)1-HINGE SLOT
SEALANT
Inspect1
(b)1621ABBLOWOUT DOOROpen2
(c)1-HINGE SLOT
SEALANT
Inspect3
(a) With the blowout door closed, do a detailed inspection of the area at the inboard and outboard ends of
the blowout door hinge for continuous sealant. All visible space at the ends of the hinge to the inboard
and outboard edges of the blowout door, and from the forward edge of the blowout door to the aft edge
of the strakelet skin must be continuously filled with sealant and faired to the external surface. If the
sealant applied to the internal and external surfaces are not sealed as described, then the space at the
inboard and outboard end of the hinge is not sealed.
(b) Open the blowout door. Refer to 737-7/8/8200/9/10 AMM 57-41-02 as an accepted procedure.
(c) With the blowout door open, do a detailed inspection of the hinge area at the inboard and outboard ends
of the blowout for continuous sealant along the seal. For the sealant applied to the internal surface to be
continuous, it must be formed to match the profile of the edges of the blowout door and hinge, with no
surface defects, and it must be bonded to the seal and the blowout door surround. If the sealant applied
to the internal and external surfaces are not sealed as described, then the space at the inboard and out-
board end of the hinge is not sealed.
FIGURE 6: RIGHT WING - OUTBOARD BLOWOUT DOOR - DETAILED INSPECTION
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 23, 2020
737-57A1350 RB
33 of 42
REQUIREMENTS BULLETIN 737-57A1350
ALERTALERT

### Page 34 (OCR)

REQUIREMENTS BULLETIN 737-57A1350
ALERT  ALERT
STRAKELET
.O  13 4€
BLOWOUT
DOOR
LOWER
SKIN PANEL
RIGHT WING
(VIEW LOOKING UP)
INBD  2927179
FIGURE 7: RIGHT WING - SEALANT APPLICATION
(SHEET 1 OF 3)
Original Issue: April 23, 2020
Export Controlled ECCN: 9E991  737-57A1350 RB
Copyright © Unpublished
Work - See page 1 for details.  34 of 42

### Page 35

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for one side of the airplane.
More DataQtyIdentificationNameTaskStep
(a)1621ABBLOWOUT DOOROpen1
-1-BLOWOUT DOOR
SURROUND
Clean2
(b)--BLOWOUT DOOR
SURROUND
Prepare
(c)--BLOWOUT DOOR
SURROUND
Clean3
(c)-621ABBLOWOUT DOORClean
(d)-FREKOTE 710-NCRELEASE AGENTApply4
(e)-BMS 5-45 B-1/2SEALANTApply5
FIGURE 7: RIGHT WING - SEALANT APPLICATION
(SHEET 2 OF 3)
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 23, 2020
737-57A1350 RB
35 of 42
REQUIREMENTS BULLETIN 737-57A1350
ALERTALERT

### Page 36

More DataQtyIdentificationNameTaskStep
(f)1621ABBLOWOUT DOORClose6
(g)(h)(i)-BMS 5-45 B-1/2SEALANTClean7
(a) Open the blowout door. Refer to 737-7/8/8200/9/10 AMM 57-41-02 as an accepted procedure.
(b) Abrade any existing cured sealant with 180 grit or finer sandpaper to remove all surface gloss where de-
veloper contact is not continuous.
(c) Clean and prepare surfaces for sealant and release agent application at existing seal location on the
blowout door and blowout door surround. Refer to SOPM 20-50-19 as an accepted procedure.
(d) Apply two coats of release agent to the blowout door surface in contact with the blowout door surround,
allowing 5-10 minutes after each application to cure. Extend the release agent as needed to ease the
removal of sealant squeeze out. Do not apply to the blowout door surround.
(e) Apply sealant BMS5-45, Class B-1/2 or optional BMS 5-182, Type 1, Class B-1/2, or PR-1826 primer and
sealant to the areas of the blowout door surround where contact was not made between the blowout door
and blowout door surround. Refer to SOPM 20-50-19 as an accepted procedure.
(f) Close and latch the blowout door. Refer to 737-7/8/8200/9/10 AMM 57-41-02 as an accepted procedure.
Make sure 20 minutes has passed after second application of release agent before closing the blowout
door.
(g) While the form-in-place gasket sealant is still wet, remove the excess sealant between the edges of both
door and the blowout door surround, fair the sealant at support structure edges and wait for the sealant
to dry.
(h) After the sealant dries, open and close the blowout door to break it free from the sealant. After cycling
the door, the door should open without assistance. Make sure that the sealant bonds to the blowout door
surround and not the blowout door. Remove any sealant that has adhered to the blowout door. Refer to
SOPM 20-50-19 as an accepted procedure. Petrolatum or Krytox may be applied to the door as a post
cure lubricant. If petrolatum is applied to the door after the sealant has cured, it must be wiped off with a
lint-free rag leaving behind a thin film. If Krytox is used, it does not have to be wiped off.
(i) Make sure sealant has formed along the existing seal on the blowout door surround at the areas where
contact was not made.
FIGURE 7: RIGHT WING - SEALANT APPLICATION
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 23, 2020
737-57A1350 RB
36 of 42
REQUIREMENTS BULLETIN 737-57A1350
ALERTALERT

### Page 37 (OCR)

REQUIREMENTS BULLETIN 737-57A1350
ALERT  ALERT
STRAKELET
E
BLOWOUT
DOOR
LOWER
SKIN PANEL
RIGHT WING
BLOWOUT DOOR SEALANT PRESENT
(VIEW LOOKING UP)
INBD
2927167
FIGURE 8: RIGHT WING - OUTBOARD BLOWOUT DOOR - SEALANT APPLICATION
(SHEET 1 OF 6)
Original Issue: April 23, 2020
Export Controlled ECCN: 9E991  Copyright © Unpublished  737-57A1350 RB
Work - See page 1 for details.  37 of 42

### Page 38 (OCR)

REQUIREMENTS BULLETIN 737-57A1350
ALERT  ALERT
BLOWOUT
DOOR
BLOWOUT 2  DOOR  STRAKELET
SURROUND
BLOWOUT PANEL
(OUTBOARD HINGE AREA PREPARATION)
ІПОМОTE
STRAKELET  2) BLOWOUT
DOOR
SURROUND
W
BLOWOUT PANEL
(INBOARD HINGE AREA PREPARATION)
SEALANT APPLICATION AREA  2927166
FIGURE 8: RIGHT WING - OUTBOARD BLOWOUT DOOR - SEALANT APPLICATION
(SHEET 2 OF 6)
Original Issue: April 23, 2020
Export Controlled ECCN: 9E991  737-57A1350 RB
Work - See page 1 for details.  Copyright © Unpublished  38 0f 42

### Page 39 (OCR)

REQUIREMENTS BULLETIN 737-57A1350
ALERT  ALERT
STRAKELET
SEAL
OUTBOARD HINGE END
(SEALANT PENETRATION
- BLOWOUT DOOR NOT SHOWN FOR CLARITY)
STRAKELET
SEAL
INBOARD HINGE END
(SEALANT PENETRATION
-BLOWOUT DOOR NOT SHOWN FOR CLARITY)
SEALANT APPLICATION AREA  2927165
FIGURE 8: RIGHT WING - OUTBOARD BLOWOUT DOOR - SEALANT APPLICATION
(SHEET 3 OF 6)
Original Issue: April 23, 2020
Export Controlled ECCN: 9E991  Copyright © Unpublished  737-57A1350 RB
Work - See page 1 for details.  39 of 42

### Page 40 (OCR)

REQUIREMENTS BULLETIN 737-57A1350
ALERT  ALERT
BLOWOUT
DOOR  SEALANT
STRAKELET
BLOWOUT PANEL
(INBOARD HINGE AREA SEALANT APPLICATION)
BLOWOUT
DOOR
(67
STRAKELET
BLOWOUT PANEL
(OUTBOARD HINGE AREA SEALANT APPLICATION)
SEALANT APPLICATION AREA  2927162
FIGURE 8: RIGHT WING - OUTBOARD BLOWOUT DOOR - SEALANT APPLICATION
(SHEET 4 OF 6)
Original Issue: April 23, 2020
Export Controlled ECCN: 9E991  737-57A1350 RB
Copyright © Unpublished
Work - See page 1 for details.  40 of 42

### Page 41

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for one side of the airplane.
More DataQtyIdentificationNameTaskStep
(a)1621ABBLOWOUT DOOROpen1
(b)-621ABBLOWOUT DOORClean2
(b)--BLOWOUT DOOR
SURROUND
Clean
(c)-FREKOTE 710-NCRELEASE AGENTApply3
(d)-BMS 5-45 B-1/2SEALANTApply4
(e)1621ABBLOWOUT DOORClose5
(f)-BMS 5-45 B-1/2SEALANTApply6
(g)(h)-BMS 5-45 B-1/2SEALANTClean7
(a) Open the blowout door. Refer to 737-7/8/8200/9/10 AMM 57-41-02 as an accepted procedure.
(b) Clean and prepare surfaces for sealant and release agent application at both ends of the blowout door
hinge, blowout door surround and blowout door. Refer to SOPM 20-50-19 as an accepted procedure.
(c) Apply two coats of release agent to the blowout door inner surface and edges that will be in contact with
wet sealant and blowout door surround, allowing 5-10 minutes after each application to cure. Allow 20
minutes after the second application before closing the door. Extend the release agent as needed to ease
the removal of sealant squeeze out. As an option you may apply the Frekote to the entire side of the door
panel. Do not apply to the door surround structure.
(d) Apply sealant BMS5-45, Class B-1/2 or optional BMS 5-182, Type 1, Class B-1/2, or PR-1826 primer and
sealant to the space between the blowout door and the blowout door surround. Refer to SOPM 20-50-19
as an accepted procedure. Make sure sealant is backfilled into the recesses in the space before topping
off. Apply enough sealant so that excess will squeeze out and make sure the space is completely filled.
(e) Close and latch door assembly. Refer to 737-7/8/8200/9/10 AMM 57-41-02 as an accepted procedure.
(f) While the sealant is still wet, remove the squeeze-out sealant between the edges of both blowout door
and the blowout door surround, except in the area of the intended filled space shown in view F and G.
Fair the sealant in the area with the surrounding external surfaces so that the faired sealant has filled the
space completely, and wait for the sealant to dry.
(g) After the sealant dries, open and close the blowout door to break it free from the sealant. After cycling
the door, the door should open without assistance. Make sure that the sealant bonds to the door structure
and not the blowout door. Refer to SOPM 20-50-19 as an accepted procedure. Krytox or Petrolatum may
be applied to the door as a post-cure lubricant. If petrolatum is applied to the door after the sealant has
cured, it must be wiped off with a lint-free rag leaving behind a thin film. If Krytox is used, it does not have
to be wiped off.
FIGURE 8: RIGHT WING - OUTBOARD BLOWOUT DOOR - SEALANT APPLICATION
(SHEET 5 OF 6)
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 23, 2020
737-57A1350 RB
41 of 42
REQUIREMENTS BULLETIN 737-57A1350
ALERTALERT

### Page 42

More DataQtyIdentificationNameTaskStep
(h) With the blowout door open, make sure the sealant has formed to continuously match the profile of the
edges of the blowout door and hinge half, with no surface defects, and make sure it is bonded to the bulb
seal and the surround structure inboard and outboard of the bulb seal. With the blowout door closed,
make sure all visible space inboard and outboard of the ends of the hinge to the inboard and outboard
edges of the door, and from the forward edge of the door to the aft edge of the strakelet skin are continu-
ously filled with sealant and faired to the external surface.
FIGURE 8: RIGHT WING - OUTBOARD BLOWOUT DOOR - SEALANT APPLICATION
(SHEET 6 OF 6)
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 23, 2020
737-57A1350 RB
42 of 42
REQUIREMENTS BULLETIN 737-57A1350
ALERTALERT

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
