# Boeing Alert Requirements Bulletin 737-57A1358 RB: No revision named, part 1 of 2

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2026-2716; AD 2026-21-07 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Alert Requirements Bulletin 737-57A1358 RB](https://openairdocs.org/service-documents/boeing/737-57a1358-rb.md)
- Title as filed: 737-57A1358 RB -Part 1
- Pages: 33
- PDF: https://openairdocs.org/files/sha256/64/6a/646acca96d631b6466273bf8453f73fd0a7875a9ac064391ca61ef58b694e069
- Page: https://openairdocs.org/service-documents/boeing/737-57a1358-rb/file/646acca96d63

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Commercial 
Airplanes
737
Requirements Bulletin
ALERT
Number: 737-57A1358 RB
Original Issue: November 17, 2025
ATA System: 5741
SUBJECT: WINGS - Wing Leading Edge - Engine Fuel Shutoff Valve Access Panel Inspection
and Test
EXPORT CONTROLLED - This technology or software is subject to the U.S. Export Administration Regulations
(EAR), (15 C.F.R. Parts 730-774). No authorization from the U.S. Department of Commerce is required for
export, re-export, in-country transfer, or access EXCEPT to country group E:1 or E:2 countries/persons per
Supp.1 to Part 740 of the EAR.
9E991ECCN:
Copyright © 2025 The Boeing Company
Treatment of this document and its content is governed by contract with Boeing. Rights to use this document
are licensed on a per aircraft basis and such rights may not be transferable. For more information, contact The
Boeing Company.
Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner,
BBJ, DC-8, DC-9, DC-10, KC-10, KC-46, KDC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8, Poseidon and
Boeing liveries are all trademarks owned by The Boeing Company; and no trademark license is granted in
connection with this document unless provided in writing by Boeing.
Original Issue: November 17, 2025
737-57A1358 RB
1 of 63
4.0

### Page 2

Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: November 17, 2025
737-57A1358 RB
2 of 63
REQUIREMENTS BULLETIN 737-57A1358
ALERTALERT
BLANK PAGE

### Page 3

Table of Contents
1. EFFECTIVITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
A. Airplanes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
B. Spares Affected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2. CONCURRENT REQUIREMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3. COMPLIANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4. APPROVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5. ACCOMPLISHMENT INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
A. General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
B. Work Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
FIGURE 1: LEFT WING - ENGINE FUEL SHUTOFF VALVE ACCESS PANEL - FORM-IN-PLACE (FIP)
GASKET DETAILED INSPECTION (DET) [Group 1] . . . . . . . . . . . . . . . . . . . . . 22
FIGURE 2: RIGHT WING - ENGINE FUEL SHUTOFF VALVE ACCESS PANEL - FORM-IN-PLACE (FIP)
GASKET DETAILED INSPECTION (DET) [Group 1] . . . . . . . . . . . . . . . . . . . . . 25
FIGURE 3: LEFT WING - ENGINE FUEL SHUTOFF VALVE ACCESS PANEL - FORM-IN-PLACE (FIP)
GASKET REPLACEMENT [Group 1] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
FIGURE 4: RIGHT WING - ENGINE FUEL SHUTOFF VALVE ACCESS PANEL - FORM-IN-PLACE (FIP)
GASKET REPLACEMENT [Group 1] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
FIGURE 5: LEFT WING - ENGINE FUEL SHUTOFF VALVE ACCESS PANEL - PRE-FORMED SEAL AREA
DETAILED INSPECTION (DET) [Group 2] . . . . . . . . . . . . . . . . . . . . . . . . . . 38
FIGURE 6: RIGHT WING - ENGINE FUEL SHUTOFF VALVE ACCESS PANEL - PRE-FORMED SEAL
AREA DETAILED INSPECTION (DET) [Group 2] . . . . . . . . . . . . . . . . . . . . . . 41
FIGURE 7: LEFT WING - ENGINE FUEL SHUTOFF VALVE ACCESS PANEL - REMOVEABLE FAY SEAL
REPLACEMENT [Group 2] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
FIGURE 8: RIGHT WING - ENGINE FUEL SHUTOFF VALVE ACCESS PANEL - REMOVEABLE FAY
SEAL REPLACEMENT [Group 2] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
APPENDIX A: LEFT WING - ENGINE FUEL SHUTOFF VALVE ACCESS PANEL - FLUID LEAK TEST . 54
APPENDIX B: RIGHT WING - ENGINE FUEL SHUTOFF VALVE ACCESS PANEL - FLUID LEAK TEST. 59
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: November 17, 2025
737-57A1358 RB
3 of 63
REQUIREMENTS BULLETIN 737-57A1358
ALERTALERT

### Page 4

Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: November 17, 2025
737-57A1358 RB
4 of 63
REQUIREMENTS BULLETIN 737-57A1358
ALERTALERT
BLANK PAGE

### Page 5

Commercial 
Airplanes
737
Requirements Bulletin
ALERT
Number: 737-57A1358 RB
Original Issue: November 17, 2025
ATA System: 5741
SUBJECT: WINGS - Wing Leading Edge - Engine Fuel Shutoff Valve Access Panel Inspection
and Test
THIS DOCUMENT IS SENT TO THE OPERATORS OF RECORD OF THE AIRPLANES SHOWN IN
EFFECTIVITY. IF AN AIRPLANE HAS BEEN LEASED OR SOLD, SEND THIS DOCUMENT TO THE NEW
OPERATOR. IF APPLICABLE SPARES HAVE BEEN SOLD, SEND THIS DOCUMENT TO THE NEW OWNER.
THIS IS AN ENHANCED REQUIRED FOR COMPLIANCE DOCUMENT. THE BOEING PROCESSES USED
TO CREATE THE SERVICE BULLETIN (SB) AND THE REQUIREMENTS BULLETIN (RB) ENSURE THAT
THE INFORMATION BETWEEN "RC START" AND "RC END" IN THE SB ARE IDENTICAL TO THE
INFORMATION IN THE SAME SECTIONS (COMPLIANCE, WORK INSTRUCTIONS…) OF THE RB WHICH
THE SB REFERS TO AS THE RELATED DOCUMENT.
1. Effectivity
A. Airplanes
This bulletin is applicable to 737-8, 737-9, 737-8200 Airplane(s), line number(s) 5602, 5668, 5788,
5852, 5902, 5948, 5992, 6034, 6074, 6114, 6154, 6188, 6222, 6272, 6290, 6308, 6326, 6344,
6360, 6372, 6384, 6396, 6408, 6420, 6430, 6441, 6448, 6456, 6464, 6472, 6481, 6490, 6499,
6508, 6515, 6521, 6528, 6535, 6542, 6548, 6555, 6562, 6569, 6575, 6582, 6589, 6594, 6598,
6603, 6607, 6612, 6616, 6621, 6625, 6630, 6634, 6639, 6643, 6648, 6652, 6657, 6661, 6666,
6672, 6677, 6681, 6686, 6690, 6695, 6699, 6704, 6708, 6713, 6717, 6722, 6726, 6731, 6735,
6740, 6749, 6753, 6758, 6762, 6767, 6771, 6776, 6780, 6783, 6785, 6789, 6792, 6794, 6796,
6803, 6805, 6807, 6810, 6814, 6816, 6819, 6821, 6825, 6828, 6830, 6834, 6837, 6839, 6841,
6843, 6848, 6850, 6852, 6855, 6859, 6861, 6864, 6866, 6868, 6872, 6875, 6877, 6881, 6884,
6886, 6890, 6893, 6895, 6897, 6899, 6904, 6906, 6908, 6911, 6915, 6917, 6920, 6922, 6926,
6929, 6931, 6935, 6938, 6940, 6942, 6944, 6949, 6951, 6953, 6956, 6960, 6963, 6965, 6968,
6970, 6973, 6975-6976, 6978, 6980, 6983, 6985, 6988, 6990-6991, 6993, 6995, 6998, 7000, 7003,
7005-7006, 7008, 7010, 7013, 7015, 7018, 7020, 7023, 7025, 7027-7028, 7030, 7033, 7035, 7038,
7040, 7042-7043, 7045, 7048, 7050, 7053, 7055, 7060, 7062, 7064-7065, 7068, 7070, 7073, 7075,
7077, 7079-7080, 7083, 7085, 7088, 7090, 7093, 7095-7096, 7098, 7100, 7103, 7105, 7108,
7110-7111, 7113, 7115, 7118, 7120, 7123, 7125, 7128, 7130, 7132-7133, 7135, 7138, 7140, 7143,
7145, 7147-7148, 7150, 7153, 7155, 7158, 7160, 7163, 7165-7166, 7168, 7170, 7173, 7175, 7178,
7180-7181, 7183, 7185-7186, 7188, 7190, 7192-7193, 7195-7196, 7198, 7200-7201, 7203, 7205,
7207-7208, 7210-7211, 7213, 7215-7216, 7218, 7220, 7222-7223, 7225-7226, 7228, 7230-7231,
7233, 7236-7238, 7240-7241, 7245-7246, 7248, 7250, 7252-7253, 7255-7256, 7258, 7260-7261,
7265, 7267-7268, 7270-7271, 7273, 7275-7276, 7278, 7281-7283, 7285-7286, 7288, 7290-7291,
7293, 7295-7296, 7298, 7300-7301, 7303, 7305-7306, 7308, 7310-7311, 7313, 7315-7316, 7318,
7320-7321, 7323, 7325-7326, 7328, 7330-7331, 7333, 7335-7336, 7338, 7340-7341, 7343, 7345,
7348, 7350, 7353, 7355-7356, 7358, 7360-7361, 7363, 7365-7366, 7368, 7370, 7373, 7375-7376,
7378, 7380-7381, 7383-7386, 7388-7391, 7393-7396, 7398-7401, 7403-7406, 7409-7411,
7413-7414, 7416, 7418-7421, 7423-7425, 7428-7431, 7433-7436, 7438-7439, 7441, 7443-7446,
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: November 17, 2025
737-57A1358 RB
5 of 63

### Page 6

7448-7449, 7451, 7453-7454, 7456, 7458-7461, 7463-7466, 7468-7470, 7473-7476, 7478-7481,
7483-7484, 7486, 7489, 7491, 7494-7495, 7498-7501, 7503-7505, 7509, 7513-7516, 7518,
7520-7521, 7523-7526, 7531, 7533-7536, 7538-7541, 7543, 7548-7551, 7553-7556, 7558-7561,
7563-7566, 7568-7569, 7571, 7573-7574, 7576, 7578-7580, 7583, 7585-7586, 7588-7591,
7593-7594, 7596, 7598-7602, 7604-7609, 7612, 7614, 7617-7618, 7620-7623, 7626-7629,
7632-7637, 7639-7641, 7643, 7648-7650, 7652-7658, 7661, 7663-7665, 7667-7670, 7672-7675,
7678-7679, 7681-7684, 7686, 7688-7689, 7692-7696, 7698-7702, 7704, 7707, 7709-7712,
7717-7719, 7721-7722, 7724-7727, 7729-7737, 7739-7740, 7742-7745, 7747-7749, 7752-7753,
7755-7756, 7758-7759, 7762-7763, 7765-7767, 7769-7773, 7776-7781, 7783, 7785-7791,
7793-7794, 7797, 7799, 7801-7808, 7810-7812, 7814-7816, 7818-7819, 7821-7825, 7827,
7829-7830, 7832, 7835-7837, 7839-7847, 7849-7857, 7861-7864, 7866, 7868-7871, 7873-7874,
7876-7877, 7879-7886, 7889-7904, 7909, 7913, 7915-7918, 7922, 7926-7928, 7937, 7942-7943,
7946-7947, 7951, 7957, 7959-7961, 7965, 7967, 7975-7976, 7982, 7984, 7990, 7992, 7994, 7996,
7998-8000, 8002-8003, 8006, 8009, 8013, 8016, 8019-8021, 8023-8024, 8033-8036, 8042-8044,
8047, 8051-8052, 8054, 8063, 8066, 8071-8073, 8075, 8077, 8087, 8090-8092, 8094, 8099,
8101-8102, 8104-8124, 8126-8133, 8135-8138, 8140-8141, 8143-8146, 8148-8149, 8151-8155,
8157-8176, 8179, 8182, 8184, 8187-8188, 8191-8193, 8195-8196, 8199-8202, 8204, 8207, 8210,
8215-8218, 8222-8224, 8226-8228, 8230-8233, 8236-8238, 8240-8241, 8243, 8245-8247,
8249-8252, 8255-8256, 8258-8259, 8261-8262, 8264-8265, 8267, 8269, 8271-8279, 8281-8283,
8286-8287, 8289-8290, 8292, 8298-8299, 8301, 8304, 8309-8311, 8313-8314, 8316, 8319,
8322-8326, 8329-8330, 8335-8336, 8340-8341, 8343-8346, 8348-8353, 8355-8363, 8365-8371,
8374-8381, 8383-8386, 8388-8389, 8391-8392, 8394-8396, 8398-8399, 8401-8402, 8404-8410,
8412-8419, 8421-8448, 8450-8487, 8489-8494, 8496-8516, 8518-8525, 8527-8529, 8532-8534,
8536, 8541-8542, 8544, 8546, 8580, 8586, 8590, 8593, 8605-8606, 8609-8610, 8612-8614,
8616-8619, 8621-8622, 8624-8633, 8635-8641, 8643-8665, 8667, 8669-8679, 8681-8696,
8699-8718, 8720-8724, 8726-8745, 8747-8748, 8750, 8752-8756, 8758-8770, 8772-8774,
8776-8794, 8797-8806, 8808-8817, 8820-8829, 8831-8833, 8835-8837, 8839-8842, 8844, 8847,
8854, 8856-8857, 8859-8860, 8862-8863, 8865, 8867-8868, 8870, 8873, 8875, 8877-8878,
8880-8881, 8884, 8887, 8890, 8893, 8898, 8900, 8906 in 2 Group(s). Where the effectivity is
presented with hyphens between line numbers, the airplane applicability means "through" and
"inclusive", e.g. line numbers 1-9 means line numbers 1 through 9 inclusive.
The Variable Numbers and Group Information for the applicable airplanes is given below.
DESCRIPTIONCONFIGURATIONGROUP
737-8, -8200 Airplanes with a Form-in-Place (FiP) gasket.-1
737-9 Airplanes with a pre-formed rubber seal.-2
Airplane Models:
737-8, 737-8200, 737-9
GroupVariable Number
11A001 - 1A002
11A004 - 1A062
11A070 - 1A093
GroupVariable Number
11A098 - 1A099
11A101 - 1A151
11A153 - 1A156
GroupVariable Number
11A158
11A162
11A190 - 1A197
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: November 17, 2025
737-57A1358 RB
6 of 63
REQUIREMENTS BULLETIN 737-57A1358
ALERTALERT

### Page 7

GroupVariable Number
11A201 - 1A209
11A211 - 1A215
11A251 - 1A253
11A301 - 1A332
11A366
11A386 - 1A393
11A401 - 1A414
11A416
11A418 - 1A425
11A427 - 1A428
11A451 - 1A467
11A476 - 1A498
11A501 - 1A502
11A521 - 1A523
11A531
11A541 - 1A547
11A549
11A601 - 1A614
11A631
11A676 - 1A691
11A726 - 1A730
11A741 - 1A743
11A751 - 1A761
11A801
11A851 - 1A880
11A884
11A887 - 1A893
11A895 - 1A897
11A916 - 1A921
11A926 - 1A934
11A943 - 1A945
11A951 - 1A964
11A967 - 1A969
GroupVariable Number
11B001 - 1B032
11B035 - 1B039
11B041 - 1B047
11B071 - 1B072
11B101 - 1B142
11B156 - 1B167
11B201 - 1B214
11B216 - 1B217
11B251 - 1B266
11B326 - 1B329
11B366 - 1B370
11B376 - 1B381
11B385 - 1B393
11B396 - 1B398
11B401 - 1B402
11B405
11B411 - 1B412
11B436 - 1B437
11B491 - 1B497
11B511 - 1B512
11B516 - 1B517
11B521 - 1B522
11B531 - 1B534
11B540 - 1B541
11B566 - 1B570
11B576 - 1B578
11B601
11B635 - 1B636
11B651 - 1B657
11B701 - 1B704
11B785 - 1B786
11B795 - 1B796
11B801 - 1B815
GroupVariable Number
11B820 - 1B825
11B831 - 1B835
11B930 - 1B934
11B944
11C001 - 1C005
11C007 - 1C009
11C011
11C201 - 1C202
11C221 - 1C224
11C237 - 1C240
11C246
11C256 - 1C267
11C301 - 1C310
11C326 - 1C335
11C401 - 1C404
11C406 - 1C408
11C410
11C414 - 1C420
11C451
11C453
11C501 - 1C517
11C690 - 1C694
11C701 - 1C720
11C826 - 1C827
11C844 - 1C845
11C861 - 1C863
11C886
11C946 - 1C950
21D002 - 1D004
21D051 - 1D079
21D081
21D101 - 1D155
21D162 - 1D179
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: November 17, 2025
737-57A1358 RB
7 of 63
REQUIREMENTS BULLETIN 737-57A1358
ALERTALERT

### Page 8

GroupVariable Number
21D201 - 1D204
21D236 - 1D238
21D251 - 1D253
21D401 - 1D404
21D426 - 1D449
21D455 - 1D464
21D466 - 1D470
21D501 - 1D503
21D521 - 1D524
21D531 - 1D534
21D601 - 1D616
21D618 - 1D619
21D701
21D703
21D751 - 1D767
21D886 - 1D887
11F001 - 1F094
11F101
11F110 - 1F149
11F151
11J001 - 1J002
11J021 - 1J023
11J041 - 1J044
11J066 - 1J067
11J101 - 1J114
11J122 - 1J126
11J132 - 1J133
11J301 - 1J302
GroupVariable Number
11J401 - 1J404
11J585
11J590 - 1J594
11J601 - 1J602
11J606
11J611
11J926 - 1J932
11K001 - 1K003
11K018
11K041 - 1K043
11K045
11K086
11K101 - 1K103
11K301 - 1K309
11K311 - 1K314
11K351 - 1K355
11K380
11K384
11K401 - 1K402
11K426
11K447 - 1K449
11K701 - 1K704
11K726 - 1K727
11K731 - 1K732
11K751
11K976 - 1K979
11L001
11L075 - 1L078
GroupVariable Number
11L084
11L266 - 1L268
11L403 - 1L404
11L451 - 1L466
11L468 - 1L483
11L489 - 1L496
11L498 - 1L499
11L501 - 1L517
11L519 - 1L523
11L525
11L558 - 1L560
11L701
11M003 - 1M005
11M201
11M203
11M205 - 1M207
11M841 - 1M843
11M951 - 1M952
11N209 - 1N230
11N232 - 1N240
11N242 - 1N245
11N247 - 1N251
11N253 - 1N257
11N501 - 1N502
11N701 - 1N702
11N851
--
--
B. Spares Affected
None.
2. CONCURRENT REQUIREMENTS
None.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: November 17, 2025
737-57A1358 RB
8 of 63
REQUIREMENTS BULLETIN 737-57A1358
ALERTALERT

### Page 9

3. COMPLIANCE
The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to
Requirements Bulletin 737-57A1358 RB. The Airworthiness Directive will make the compliance tasks and
times given in Requirements Bulletin 737-57A1358 RB mandatory.
Group 1:
Accomplish the required action(s), based on the applicable condition(s) in Table 1 and Table 2 in accordance
with Accomplishment Instructions.
Group 2:
Accomplish the required action(s), based on the applicable condition(s) in Table 3 and Table 4 in accordance
with Accomplishment Instructions.
When more than one OPTION is given for a CONDITION, do only one of the OPTION numbers. When
more than one ACTION is given for a CONDITION or an OPTION, do all of the ACTION numbers for that
CONDITION or OPTION.
Group 1:
Table 1: Form-in-Place (FiP) Gasket Detailed Inspection (DET) and Replacement, and Fluid Leak
Test of Engine Fuel Shutoff Valve Access Panel at Wing Leading Edge, Left Wing
Repeat Inter-
val (Not to
Exceed)
Boeing Recommended
Compliance Time
ActionCondition
-Within 36 months after
the Original Issue date of
Requirements Bulletin
737-57A1358 RB.
Do a DET of the FiP gasket at
the engine fuel shutoff valve
access panel for correct
sealant installation. (a)
All Airplanes.
-Before further flight.CONDITION 1 (ACTION 1):CONDITION 1:
Replace the FiP gasket.INCORRECT SEALANT
INSTALLATION FOUND. CONDITION 1 (ACTION 2):
Do a fluid leak test of the en-
gine fuel shutoff valve access
panel for any leak. If any leak
is found, do all applicable on-
condition corrective action(s)
and repeat the leak test until
no leak is found.
-Before further flight.Do a fluid leak test of the en-
gine fuel shutoff valve access
panel for any leak. If any leak
is found, do all applicable on-
condition corrective action(s)
and repeat the leak test until
no leak is found.
CONDITION 2:
CORRECT SEALANT IN-
STALLATION FOUND.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: November 17, 2025
737-57A1358 RB
9 of 63
REQUIREMENTS BULLETIN 737-57A1358
ALERTALERT

### Page 10

Group 1:
Table 1: Form-in-Place (FiP) Gasket Detailed Inspection (DET) and Replacement, and Fluid Leak
Test of Engine Fuel Shutoff Valve Access Panel at Wing Leading Edge, Left Wing
Repeat Inter-
val (Not to
Exceed)
Boeing Recommended
Compliance Time
ActionCondition
(a) Correct sealant installation is defined as:
1. No structure is visible in the FiP gasket area.
2. The sealing surface is smooth.
3. No sealant touch-up is added after the initial sealant application. Touch-up is identified
by irregular, smeared, or thicker regions with different texture or appearance from the
surrounding sealant, often with visible brush or tool marks.
4. Any small cavity or depression in the sealing surface which are less than or equal to
1/4 inch in width, and 1/8 inch in length, are permitted if the cavities or depressions
do not extend across the full width of the sealed surface and maintain a minimum
sealing surface of 1/4 inch.
5. The outboard aft corner of the gasket area is sealed and attached to the flange of the
main track rib assembly and attach strap.
6. The gasket is adhered to the underlying surface and is not loose.
Group 1:
Table 2: Form-in-Place (FiP) Gasket Detailed Inspection (DET) and Replacement, and Fluid Leak
Test of Engine Fuel Shutoff Valve Access Panel at Wing Leading Edge, Right Wing
Repeat Inter-
val (Not to
Exceed)
Boeing Recommended
Compliance Time
ActionCondition
-Within 36 months after
the Original Issue date of
Requirements Bulletin
737-57A1358 RB.
Do a DET of the FiP gasket at
the engine fuel shutoff valve
access panel for correct
sealant installation. (a)
All Airplanes.
-Before further flight.CONDITION 3 (ACTION 1):CONDITION 3:
Replace the FiP gasket.INCORRECT SEALANT
INSTALLATION FOUND. CONDITION 3 (ACTION 2):
Do a fluid leak test of the en-
gine fuel shutoff valve access
panel for any leak. If any leak
is found, do all applicable on-
condition corrective action(s)
and repeat the leak test until
no leak is found.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: November 17, 2025
737-57A1358 RB
10 of 63
REQUIREMENTS BULLETIN 737-57A1358
ALERTALERT

### Page 11

Group 1:
Table 2: Form-in-Place (FiP) Gasket Detailed Inspection (DET) and Replacement, and Fluid Leak
Test of Engine Fuel Shutoff Valve Access Panel at Wing Leading Edge, Right Wing
Repeat Inter-
val (Not to
Exceed)
Boeing Recommended
Compliance Time
ActionCondition
-Before further flight.Do a fluid leak test of the en-
gine fuel shutoff valve access
panel for any leak. If any leak
is found, do all applicable on-
condition corrective action(s)
and repeat the leak test until
no leak is found.
CONDITION 4:
CORRECT SEALANT IN-
STALLATION FOUND.
(a) Correct sealant installation is defined as:
1. No structure is visible in the FiP gasket area.
2. The sealing surface is smooth.
3. No sealant touch-up is added after the initial sealant application. Touch-up is identified
by irregular, smeared, or thicker regions with different texture or appearance from the
surrounding sealant, often with visible brush or tool marks.
4. Any small cavity or depression in the sealing surface which are less than or equal to
1/4 inch in width, and 1/8 inch in length, are permitted if the cavities or depressions
do not extend across the full width of the sealed surface and maintain a minimum
sealing surface of 1/4 inch.
5. The outboard aft corner of the gasket area is sealed and attached to the flange of the
main track rib assembly and attach strap.
6. The gasket is adhered to the underlying surface and is not loose.
Group 2:
Table 3: Pre-Formed Seal Area Detailed Inspection (DET) and Repair, and Fluid Leak Test of Engine
Fuel Shutoff Valve Access Panel at Wing Leading Edge, Left Wing
Repeat Inter-
val (Not to
Exceed)
Boeing Recommended
Compliance Time
ActionCondition
-Within 36 months after
the Original Issue date of
Requirements Bulletin
737-57A1358 RB.
Do a DET at the engine fuel
shutoff valve access panel for
any damage on the pre-
formed seal. (a)
All Airplanes.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: November 17, 2025
737-57A1358 RB
11 of 63
REQUIREMENTS BULLETIN 737-57A1358
ALERTALERT

### Page 12

Group 2:
Table 3: Pre-Formed Seal Area Detailed Inspection (DET) and Repair, and Fluid Leak Test of Engine
Fuel Shutoff Valve Access Panel at Wing Leading Edge, Left Wing
Repeat Inter-
val (Not to
Exceed)
Boeing Recommended
Compliance Time
ActionCondition
-Before further flight.CONDITION 5 (ACTION 1):CONDITION 5:
Contact The Boeing Company
for repair instructions and do
the repair.
PRE-FORMED SEAL
DAMAGE FOUND.
CONDITION 5 (ACTION 2):
Do a fluid leak test of the en-
gine fuel shutoff valve access
panel for any leak. If any leak
is found, do all applicable on-
condition corrective action(s)
and repeat the leak test until
no leak is found.
-Before further flight.Do a fluid leak test of the en-
gine fuel shutoff valve access
panel for any leak. If any leak
is found, replace the existing
sealant installation with a re-
movable fay seal and repeat
the leak test until no leak is
found.
CONDITION 6:
NO PRE-FORMED SEAL
DAMAGE FOUND.
(a) Pre-formed seal damage is defined as:
1. Tears or rips which extend across the full width of the pre-formed seal.
2. Partial or complete disbonding of the pre-formed seal from the access door.
Group 2:
Table 4: Pre-Formed Seal Area Detailed Inspection (DET) and Repair, and Fluid Leak Test of Engine
Fuel Shutoff Valve Access Panel at Wing Leading Edge, Right Wing
Repeat Inter-
val (Not to
Exceed)
Boeing Recommended
Compliance Time
ActionCondition
-Within 36 months after
the Original Issue date of
Requirements Bulletin
737-57A1358 RB.
Do a DET at the engine fuel
shutoff valve access panel for
any damage on the pre-
formed seal. (a)
All Airplanes.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: November 17, 2025
737-57A1358 RB
12 of 63
REQUIREMENTS BULLETIN 737-57A1358
ALERTALERT

### Page 13

Group 2:
Table 4: Pre-Formed Seal Area Detailed Inspection (DET) and Repair, and Fluid Leak Test of Engine
Fuel Shutoff Valve Access Panel at Wing Leading Edge, Right Wing
Repeat Inter-
val (Not to
Exceed)
Boeing Recommended
Compliance Time
ActionCondition
-Before further flight.CONDITION 7 (ACTION 1):CONDITION 7:
Contact The Boeing Company
for repair instructions and do
the repair.
PRE-FORMED SEAL
DAMAGE FOUND.
CONDITION 7 (ACTION 2):
Do a fluid leak test of the en-
gine fuel shutoff valve access
panel for any leak. If any leak
is found, do all applicable on-
condition corrective action(s)
and repeat the leak test until
no leak is found.
-Before further flight.Do a fluid leak test of the en-
gine fuel shutoff valve access
panel for any leak. If any leak
is found, replace the existing
sealant installation with a re-
movable fay seal and repeat
the leak test until no leak is
found.
CONDITION 8:
NO PRE-FORMED SEAL
DAMAGE FOUND.
(a) Pre-formed seal damage is defined as:
1. Tears or rips which extend across the full width of the pre-formed seal.
2. Partial or complete disbonding of the pre-formed seal from the access door.
4. APPROVAL
This Requirements Bulletin was examined by the Federal Aviation Administration (FAA). The changes
specified in this document comply with the applicable regulations and are FAA approved, as well as European
Union Aviation Safety Agency (EASA) approved for all EASA approved airplanes listed in this Requirements
Bulletin effectivity. This document and its approval were based on the airplane in its original Boeing delivery
configuration or as modified by other Boeing changes.
If an airplane has a non-Boeing modification or repair that affects a component or system also affected by
this Requirements Bulletin, the operator is responsible for obtaining appropriate regulatory agency approval
before incorporating this Requirements Bulletin.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: November 17, 2025
737-57A1358 RB
13 of 63
REQUIREMENTS BULLETIN 737-57A1358
ALERTALERT

### Page 14

Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: November 17, 2025
737-57A1358 RB
14 of 63
REQUIREMENTS BULLETIN 737-57A1358
ALERTALERT
BLANK PAGE

### Page 15

5.    ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL INFORMATION
NOTE: 1. This is an Enhanced Required for Compliance document. There will be a separate
Service Bulletin (SB) and a separate Requirements Bulletin (RB). If an RB is mandated
by an Airworthiness Directive (AD), then all applicable requirements specified in the
RB must be done. In the RB, the "Refer to the listed procedures..." column of the
table(s) in the Work Instructions is for reference only. The procedures in that column
are not required by the AD and are for guidance only. For the related SB, some
locations are marked RC Start and RC End to identify the requirements that are
restated from the RB. For the related SB, the areas between RC Start and RC End,
including sub-steps and any figures identified between RC Start and RC End, must
be done to comply with the AD. Therefore, an Alternative Method of Compliance
(AMOC) is required for any deviations to steps between RC Start and RC End,
including substeps and identified figures. For the related SB, the steps not between
RC Start and RC End may be deviated from using accepted methods in accordance
with the operator's maintenance or inspection program without obtaining approval
of an AMOC; this is provided that the steps between RC Start and RC End, including
sub-steps and identified figures, can still be done as specified, and the airplane can
be put back in an airworthy condition. Figures not required for compliance are omitted
from the RB.
2. This is an Enhanced Required for Compliance document. The Boeing processes
used to create the Service Bulletin (SB) and the Requirements Bulletin (RB) ensure
that the information between "RC Start" and "RC End" in the SB are identical to the
information in the same sections (Compliance, Work Instructions...) of the RB which
the SB refers to as the related document.
3. The compliance times for the actions in WORK INSTRUCTIONS are in Compliance.
4. Unless shown differently, these dimensions and tolerances are used:
– Linear dimensions are in inches
– Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus
or minus 0.03 inch
– Tolerance on rivet and bolt edge margin is plus or minus 0.05 inch
– Angular tolerance is plus or minus 2 degrees
– Hole dimensions for standard solid rivets and fasteners are in Structural Repair
Manual (SRM) Chapter 51
– Torque Values:
— Values for structural fasteners are given in 737 Structural Repair Manual,
Chapter 51.
— Values for airframe maintenance tasks are included in Chapter 20 of 737
Aircraft Maintenance Manual (AMM).
— Values for electrical maintenance tasks are included in Chapter 20 of
Standard Wiring Practices Manual (SWPM).
— Values for engine maintenance tasks are included in Chapter 70 of 737
Aircraft Maintenance Manual (AMM).
— Non-standard torque values for maintenance tasks are included in the
applicable installation step.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: November 17, 2025
737-57A1358 RB
15 of 63
REQUIREMENTS BULLETIN 737-57A1358
ALERTALERT

### Page 16

5. These work instructions refer to procedures included in other Boeing documents.
When the words "refer to" are used and the operator has an accepted alternative
procedure, the accepted alternative procedure can be used. When the words "in
accordance with" are included in the instruction, the procedure in the Boeing document
must be used.
6. Where the work instructions include installation of a kept part, a new or serviceable
part with the same part number can be installed as an alternative to the kept part.
7. If it is necessary to remove more parts for access, you can remove those parts. If
you can get access without removing identified parts, it is not necessary to remove
all of the identified parts. Jacking and shoring limitations must be observed.
8. Use the approved fastener, process and material substitutions in accordance with
SRM Chapter 51.
9. A Detailed Inspection (DET) is defined as: An intensive examination of a specific
item, installation or assembly to detect damage, failure or irregularity. This could
include tactile assessment in which a component or assembly can be checked for
tightness/security. Available lighting is normally supplemented with a direct source
of good lighting at an intensity deemed appropriate. Inspection aids such as mirrors
and magnifying lenses may be necessary. Surface cleaning and elaborate access
procedures may be required.
10. When more than one OPTION is given for a CONDITION, do only one of the OPTION
numbers. When more than one ACTION is given for a CONDITION or an OPTION,
do all of the ACTION numbers for that CONDITION or OPTION.
11. This service bulletin includes functional test procedures for the systems changed by
this service bulletin. More functional tests can possibly be necessary in accordance
with standard maintenance practices because of interruption to other airplane systems.
12. Use of colors in Figures is based on guidance from the ATA e-Business Program
(ATA) iSpec 2200.
B. WORK INSTRUCTIONS
Actions Required for Compliance
1. Requirements.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: November 17, 2025
737-57A1358 RB
16 of 63
REQUIREMENTS BULLETIN 737-57A1358
ALERTALERT

### Page 17

Group 1:
Table 1: Form-in-Place (FiP) Gasket Detailed Inspection (DET) and Replacement, and Fluid Leak Test
of Engine Fuel Shutoff Valve Access Panel at Wing Leading Edge, Left Wing
Refer to the listed
procedures in SB
737-57A1358 Origi-
nal Issue or later
approved revi-
sions as an accept-
ed procedure
Method of Compli-
ance
ActionCondition
PART 1: LEFT
WING OPEN AC-
CESS
-Do a DET of the FiP gasket at
the engine fuel shutoff valve
access panel for correct sealant
installation. (a)
All Airplanes.
-FIGURE 1
-FIGURE 3CONDITION 1 (ACTION 1):CONDITION 1:
Replace the FiP gasket.INCORRECT
SEALANT INSTALLA-
TION FOUND. -APPENDIX ACONDITION 1 (ACTION 2):Do a fluid leak test of the engine
fuel shutoff valve access panel
for any leak. If any leak is found,
do all applicable on-condition
corrective action(s) and repeat
the leak test until no leak is
found.
-FIGURE 3
PART 3: LEFT
WING CLOSE AC-
CESS
-
-APPENDIX ADo a fluid leak test of the engine
fuel shutoff valve access panel
for any leak. If any leak is found,
do all applicable on-condition
corrective action(s) and repeat
the leak test until no leak is
found.
CONDITION 2:
CORRECT SEALANT
INSTALLATION
FOUND.
-FIGURE 3
PART 3: LEFT
WING CLOSE AC-
CESS
-
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: November 17, 2025
737-57A1358 RB
17 of 63
REQUIREMENTS BULLETIN 737-57A1358
ALERTALERT

### Page 18

Group 1:
Table 1: Form-in-Place (FiP) Gasket Detailed Inspection (DET) and Replacement, and Fluid Leak Test
of Engine Fuel Shutoff Valve Access Panel at Wing Leading Edge, Left Wing
Refer to the listed
procedures in SB
737-57A1358 Origi-
nal Issue or later
approved revi-
sions as an accept-
ed procedure
Method of Compli-
ance
ActionCondition
(a) Correct sealant installation is defined as:
1. No structure is visible in the FiP gasket area.
2. The sealing surface is smooth.
3. No sealant touch-up is added after the initial sealant application. Touch-up is identified
by irregular, smeared, or thicker regions with different texture or appearance from the
surrounding sealant, often with visible brush or tool marks.
4. Any small cavity or depression in the sealing surface which are less than or equal to 1/4
inch in width, and 1/8 inch in length, are permitted if the cavities or depressions do not
extend across the full width of the sealed surface and maintain a minimum sealing surface
of 1/4 inch.
5. The outboard aft corner of the gasket area is sealed and attached to the flange of the
main track rib assembly and attach strap.
6. The gasket is adhered to the underlying surface and is not loose.
Group 1:
Table 2: Form-in-Place (FiP) Gasket Detailed Inspection (DET) and Replacement, and Fluid Leak Test
of Engine Fuel Shutoff Valve Access Panel at Wing Leading Edge, Right Wing
Refer to the listed
procedures in SB
737-57A1358 Origi-
nal Issue or later
approved revi-
sions as an accept-
ed procedure
Method of Compli-
ance
ActionCondition
PART 2: RIGHT
WING OPEN AC-
CESS
-Do a DET of the FiP gasket at
the engine fuel shutoff valve
access panel for correct sealant
installation. (a)
All Airplanes.
-FIGURE 2
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: November 17, 2025
737-57A1358 RB
18 of 63
REQUIREMENTS BULLETIN 737-57A1358
ALERTALERT

### Page 19

Group 1:
Table 2: Form-in-Place (FiP) Gasket Detailed Inspection (DET) and Replacement, and Fluid Leak Test
of Engine Fuel Shutoff Valve Access Panel at Wing Leading Edge, Right Wing
Refer to the listed
procedures in SB
737-57A1358 Origi-
nal Issue or later
approved revi-
sions as an accept-
ed procedure
Method of Compli-
ance
ActionCondition
-FIGURE 4CONDITION 3 (ACTION 1):CONDITION 3:
Replace the FiP gasket.INCORRECT
SEALANT INSTALLA-
TION FOUND. -APPENDIX BCONDITION 3 (ACTION 2):Do a fluid leak test of the engine
fuel shutoff valve access panel
for any leak. If any leak is found,
do all applicable on-condition
corrective action(s) and repeat
the leak test until no leak is
found.
-FIGURE 4
PART 4: RIGHT
WING CLOSE AC-
CESS
-
-APPENDIX BDo a fluid leak test of the engine
fuel shutoff valve access panel
for any leak. If any leak is found,
do all applicable on-condition
corrective action(s) and repeat
the leak test until no leak is
found.
CONDITION 4:
CORRECT SEALANT
INSTALLATION
FOUND.
-FIGURE 4
PART 4: RIGHT
WING CLOSE AC-
CESS
-
(a) Correct sealant installation is defined as:
1. No structure is visible in the FiP gasket area.
2. The sealing surface is smooth.
3. No sealant touch-up is added after the initial sealant application. Touch-up is identified
by irregular, smeared, or thicker regions with different texture or appearance from the
surrounding sealant, often with visible brush or tool marks.
4. Any small cavity or depression in the sealing surface which are less than or equal to 1/4
inch in width, and 1/8 inch in length, are permitted if the cavities or depressions do not
extend across the full width of the sealed surface and maintain a minimum sealing surface
of 1/4 inch.
5. The outboard aft corner of the gasket area is sealed and attached to the flange of the
main track rib assembly and attach strap.
6. The gasket is adhered to the underlying surface and is not loose.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: November 17, 2025
737-57A1358 RB
19 of 63
REQUIREMENTS BULLETIN 737-57A1358
ALERTALERT

### Page 20

Group 2:
Table 3: Pre-Formed Seal Area Detailed Inspection (DET) and Repair, and Fluid Leak Test of Engine
Fuel Shutoff Valve Access Panel at Wing Leading Edge, Left Wing
Refer to the listed
procedures in SB
737-57A1358 Origi-
nal Issue or later
approved revi-
sions as an accept-
ed procedure
Method of Compli-
ance
ActionCondition
PART 1: LEFT
WING OPEN AC-
CESS
-Do a DET at the engine fuel
shutoff valve access panel for
any damage on the pre-formed
seal. (a)
All Airplanes.
-FIGURE 5
--CONDITION 5 (ACTION 1):CONDITION 5:
Contact The Boeing Company
for repair instructions and do the
repair.
PRE-FORMED SEAL
DAMAGE FOUND.
-APPENDIX ACONDITION 5 (ACTION 2):
Do a fluid leak test of the engine
fuel shutoff valve access panel
for any leak. If any leak is found,
do all applicable on-condition
corrective action(s) and repeat
the leak test until no leak is
found.
-FIGURE 7
PART 3: LEFT
WING CLOSE AC-
CESS
-
-APPENDIX ADo a fluid leak test of the engine
fuel shutoff valve access panel
for any leak. If any leak is found,
replace the existing sealant in-
stallation with a removable fay
seal and repeat the leak test
until no leak is found.
CONDITION 6:
NO PRE-FORMED
SEAL DAMAGE
FOUND.
-FIGURE 7
PART 3: LEFT
WING CLOSE AC-
CESS
-
(a) Pre-formed seal damage is defined as:
1. Tears or rips which extend across the full width of the pre-formed seal.
2. Partial or complete disbonding of the pre-formed seal from the access door.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: November 17, 2025
737-57A1358 RB
20 of 63
REQUIREMENTS BULLETIN 737-57A1358
ALERTALERT

### Page 21

Group 2:
Table 4: Pre-Formed Seal Area Detailed Inspection (DET) and Repair, and Fluid Leak Test of Engine
Fuel Shutoff Valve Access Panel at Wing Leading Edge, Right Wing
Refer to the listed
procedures in SB
737-57A1358 Origi-
nal Issue or later
approved revi-
sions as an accept-
ed procedure
Method of Compli-
ance
ActionCondition
PART 2: RIGHT
WING OPEN AC-
CESS
-Do a DET at the engine fuel
shutoff valve access panel for
any damage on the pre-formed
seal. (a)
All Airplanes.
-FIGURE 6
--CONDITION 7 (ACTION 1):CONDITION 7:
Contact The Boeing Company
for repair instructions and do the
repair.
PRE-FORMED SEAL
DAMAGE FOUND.
-APPENDIX BCONDITION 7 (ACTION 2):
Do a fluid leak test of the engine
fuel shutoff valve access panel
for any leak. If any leak is found,
do all applicable on-condition
corrective action(s) and repeat
the leak test until no leak is
found.
-FIGURE 8
PART 4: RIGHT
WING CLOSE AC-
CESS
-
-APPENDIX BDo a fluid leak test of the engine
fuel shutoff valve access panel
for any leak. If any leak is found,
replace the existing sealant in-
stallation with a removable fay
seal and repeat the leak test
until no leak is found.
CONDITION 8:
NO PRE-FORMED
SEAL DAMAGE
FOUND.
-FIGURE 8
PART 4: RIGHT
WING CLOSE AC-
CESS
-
(a) Pre-formed seal damage is defined as:
1. Tears or rips which extend across the full width of the pre-formed seal.
2. Partial or complete disbonding of the pre-formed seal from the access door.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: November 17, 2025
737-57A1358 RB
21 of 63
REQUIREMENTS BULLETIN 737-57A1358
ALERTALERT

### Page 22 (OCR)

REQUIREMENTS BULLETIN 737-57A1358
ALERT  ALERT
This Figure applies only to: Group 1.
SLAT STA
36.00
•
SEAL RIB  SLAT STA  MAIN TRACK
ASSEMBLY  36.00  UPPER SKIN PANEL  RIB ASSEMBLY
LOWER SKIN  ATTACH
PANEL  STRAP
ENGINE FUEL SHUTOFF VALVE
ACCESS PANEL IS NOT SHOWN
DETAILED INSPECTION  (VIEW IN THE UP DIRECTION)  INE  3089055
AREA  A-A
FIGURE 1: LEFT WING - ENGINE FUEL SHUTOFF VALVE ACCESS PANEL - FORM-IN-PLACE (FIP)
GASKET DETAILED INSPECTION (DET)
(SHEET 1 OF 3)
Original Issue: November 17, 2025
Export Controlled ECCN: 9E991  737-57A1358 RB
See page 1 for details  22 of 63

### Page 23 (OCR)

REQUIREMENTS BULLETIN 737-57A1358
ALERT  ALERT
_ MAIN TRACK  RIB ASSEMBLY
ATTACH
STRAP
INBD
ENGINE FUEL SHUTOFF VALVE
ACCESS PANEL IS NOT SHOWN
• AREA  DETAILED INSPECTION  3089118
FIGURE 1: LEFT WING - ENGINE FUEL SHUTOFF VALVE ACCESS PANEL - FORM-IN-PLACE (FIP)
GASKET DETAILED INSPECTION (DET)
(SHEET 2 OF 3)
Original Issue: November 17, 2025
Export Controlled ECCN: 9E991  737-57A1358 RB
See page 1 for details  23 of 63

### Page 24

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
More DataQtyIdentificationNameTaskStep
(a)(b)-BMS 5-45, CLASS B-
1/2 OR B-2
SEALANT (FORM-IN-
PLACE GASKET)
Inspect1
(c)(d)-BMS 5-45, CLASS B-
1/2 OR B-2
SEALANTInspect2
(a) Correct sealant installation for step 1 is defined as:
1. No structure is visible in the FiP gasket area.
2. The sealing surface is smooth.
3. No sealant touch-up is added after the initial sealant application. Touch-up is identified by irreg-
ular, smeared, or thicker regions with different texture or appearance from the surrounding
sealant, often with visible brush or tool marks.
4. Any small cavity or depression in the sealing surface which are less than or equal to 1/4 inch in
width, and 1/8 inch in length, are permitted if the cavities or depressions do not extend across
the full width of the sealed surface and maintain a minimum sealing surface of 1/4 inch.
5. The outboard aft corner of the gasket area is sealed and attached to the flange of the main track
rib assembly and attach strap.
6. The gasket is adhered to the underlying surface and is not loose.
(b) Do a DET of the FiP gasket on the seal rib assembly, attach strap, and main track rib assembly in areas
which contact the engine fuel shutoff valve access panel for correct sealant installation.
(c) Do a DET of the sealant on the main track rib assembly adjacent to the attach strap for correct sealant
installation.
(d) Correct sealant installation for step 2 is defined as:
1. The outboard aft corner of the gasket area is sealed, attached to the flange of the main track rib
assembly and attach strap, flush with adjacent surfaces, adhered to the underlying surface and
is not loose.
FIGURE 1: LEFT WING - ENGINE FUEL SHUTOFF VALVE ACCESS PANEL - FORM-IN-PLACE (FIP)
GASKET DETAILED INSPECTION (DET)
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: November 17, 2025
737-57A1358 RB
24 of 63
REQUIREMENTS BULLETIN 737-57A1358
ALERTALERT

### Page 25 (OCR)

REQUIREMENTS BULLETIN 737-57A1358
ALERT  ALERT
This Figure applies only to: Group 1.
SLAT STA
36.00
MAIN TRACK  SLAT STA  SEAL RIB
RIB ASSEMBLY  UPPER SKIN PANEL  36.00  ASSEMBLY
ATTACH  LOWER SKIN
STRAP  PANEL
ENGINE FUEL SHUTOFF ACCESS
PANEL IS NOT SHOWN
DETAILED INSPECTION  (VIEW IN THE UP DIRECTION)
AREA  A-A
FIGURE 2: RIGHT WING - ENGINE FUEL SHUTOFF VALVE ACCESS PANEL - FORM-IN-PLACE (FIP)
GASKET DETAILED INSPECTION (DET)
(SHEET 1 OF 3)
Original Issue: November 17, 2025
Export Controlled ECCN: 9E991  737-57A1358 RB
See page 1 for details  25 of 63

### Page 26 (OCR)

REQUIREMENTS BULLETIN 737-57A1358
ALERT  ALERT
MAIN TRACK
RIB ASSEMBLY
ENGINE FUEL SHUTOFF VALVE
ACCESS PANEL IS NOT SHOWN
DETAILED INSPECTION  3089124
AREA
FIGURE 2: RIGHT WING - ENGINE FUEL SHUTOFF VALVE ACCESS PANEL - FORM-IN-PLACE (FIP)
GASKET DETAILED INSPECTION (DET)
(SHEET 2 OF 3)
Original Issue: November 17, 2025
737-57A1358 RB
Export Controlled ECCN: 9E991
See page 1 for details  26 of 63

### Page 27

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
More DataQtyIdentificationNameTaskStep
(a)(b)-BMS 5-45, CLASS B-
1/2 OR B-2
SEALANT (FORM-IN-
PLACE GASKET)
Inspect1
(c)(d)-BMS 5-45, CLASS B-
1/2 OR B-2
SEALANTInspect2
(a) Correct sealant installation for step 1 is defined as:
1. No structure is visible in the FiP gasket area.
2. The sealing surface is smooth.
3. No sealant touch-up is added after the initial sealant application. Touch-up is identified by irreg-
ular, smeared, or thicker regions with different texture or appearance from the surrounding
sealant, often with visible brush or tool marks.
4. Any small cavity or depression in the sealing surface which are less than or equal to 1/4 inch in
width, and 1/8 inch in length, are permitted if the cavities or depressions do not extend across
the full width of the sealed surface and maintain a minimum sealing surface of 1/4 inch.
5. The outboard aft corner of the gasket area is sealed and attached to the flange of the main track
rib assembly and attach strap.
6. The gasket is adhered to the underlying surface and is not loose.
(b) Do a DET of the FiP gasket on the seal rib assembly, attach strap, and main track rib assembly in areas
which contact the engine fuel shutoff valve access panel for correct sealant installation.
(c) Do a DET of the sealant on the main track rib assembly adjacent to the attach strap for correct sealant
installation.
(d) Correct sealant installation for step 2 is defined as:
1. The outboard aft corner of the gasket area is sealed, attached to the flange of the main track rib
assembly and attach strap, flush with adjacent surfaces, adhered to the underlying surface and
is not loose.
FIGURE 2: RIGHT WING - ENGINE FUEL SHUTOFF VALVE ACCESS PANEL - FORM-IN-PLACE (FIP)
GASKET DETAILED INSPECTION (DET)
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: November 17, 2025
737-57A1358 RB
27 of 63
REQUIREMENTS BULLETIN 737-57A1358
ALERTALERT

### Page 28 (OCR)

REQUIREMENTS BULLETIN 737-57A1358
ALERT  ALERT
This Figure applies only to: Group 1.
SLAT STA
36.00
•
SEAL RIB  SLAT STA  MAIN TRACK
ASSEMBLY  36.00  UPPER SKIN PANEL  RIB ASSEMBLY
LOWER SKIN  PANEL  245€0U  04500  ATTACH
STRAP
ENGINE FUEL SHUTOFF VALVE
ACCESS PANEL IS NOT SHOWN
FORM-IN-PLACE GASKET  APPLICATION AREA  (VIEW IN THE UP DIRECTION)
FORM-IN-PLACE GASKET AND  A-A  3089142
SEALANT APPLICATION AREA
FIGURE 3: LEFT WING - ENGINE FUEL SHUTOFF VALVE ACCESS PANEL - FORM-IN-PLACE (FIP)
GASKET REPLACEMENT
(SHEET 1 OF 5)
Original Issue: November 17, 2025
737-57A1358 RB
Export Controlled ECCN: 9E991
See page 1 for details  28 of 63

### Page 29 (OCR)

REQUIREMENTS BULLETIN 737-57A1358
ALERT  ALERT
MAIN TRACK
RIB ASSEMBLY
(10\11
04€0
345000
- ATTACH STRAP
INBD
ENGINE FUEL SHUTOFF VALVE ACCESS
PANEL IS SHOWN IN CLOSED POSITION
FORM-IN-PLACE GASKET
APPLICATION AREA
FORM-IN-PLACE GASKET AND  3089143
SEALANT APPLICATION AREA
FIGURE 3: LEFT WING - ENGINE FUEL SHUTOFF VALVE ACCESS PANEL - FORM-IN-PLACE (FIP)
GASKET REPLACEMENT
(SHEET 2 OF 5)
Original Issue: November 17, 2025
Export Controlled ECCN: 9E991  737-57A1358 RB
See page 1 for details  29 of 63

### Page 30

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
More DataQtyIdentificationNameTaskStep
(a)(b)--SEALANT (FORM-IN-
PLACE GASKET)
Remove1
(b)(c)--SEALANTRemove2
(b)(d)--SEALANTRemove3
(e)--CORROSION INHIBIT-
ING COMPOUND
Remove4
(f)(g)--SURFACEClean5
(h)(i)-BMS 5-45, CLASS B-
1/2 OR B-2
SEALANTApply6
(h)(j)-BMS 5-45, CLASS B-
1/2 OR B-2
SEALANTApply7
(k)(l)(m)-FREKOTE 710-NCPARTING AGENTApply8
(n)(o)-BMS 5-45, CLASS B-
1/2
SEALANT (FORM-IN-
PLACE GASKET)
Apply9
(p)(q)1521BBENGINE FUEL SHUT-
OFF VALVE ACCESS
PANEL
Open10
(b)(r)1521BBENGINE FUEL SHUT-
OFF VALVE ACCESS
PANEL
Clean11
(b)(r)(s)--SURFACEClean
(b)(t)-BMS 5-45, CLASS B-
1/2
SEALANTRemove12
(a) Remove the existing FiP gasket on the seal rib assembly, main track rib assembly, and attach strap.
(b) Use a non-metallic tool and make sure not to damage the surface of the metal or protective coating. Refer
to SOPM 20-50-19 as an accepted procedure.
(c) Remove existing sealant in the space between the seal rib assembly and adjacent attach strap.
(d) Remove existing sealant in the space between the main track rib assembly and adjacent attach strap.
Make sure all sealant is removed from the surround structure at the aft outboard side of the engine fuel
shutoff valve access panel. Remove sealant located on the underside of the main track rib assembly
flange and attach strap.
(e) Remove existing corrosion inhibiting compound from the shown surfaces where a FiP gasket or sealant
was applied. Refer to SOPM 20-50-19 as an accepted procedure.
(f) Clean the surfaces of the seal rib assembly, main track rib assembly, and attach strap which have had
the FiP gasket or sealant removed. Refer to SOPM 20-50-19 as an accepted procedure.
FIGURE 3: LEFT WING - ENGINE FUEL SHUTOFF VALVE ACCESS PANEL - FORM-IN-PLACE (FIP)
GASKET REPLACEMENT
(SHEET 3 OF 5)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: November 17, 2025
737-57A1358 RB
30 of 63
REQUIREMENTS BULLETIN 737-57A1358
ALERTALERT

### Page 31

More DataQtyIdentificationNameTaskStep
(g) If the surface finish on the structure in the shown area is cracked or shows signs of abrasion, repair
chemical and solvent resistant finish. Refer to SOPM 20-41-02 as an accepted procedure.
(h) BMS 5-45 shrinks when it cures, make sure that the sealant stays attached to the structure(s) after it
cures. It is optional to co-cure the sealant with the FiP gasket. Refer to SOPM 20-50-19 as an accepted
procedure.
(i) Fill the space between the seal rib assembly and adjacent attach strap flush with sealant.
(j) At the aft outboard side of the engine fuel shutoff valve access panel surround structure, build up the
sealant flush to fill the space between the flange of the main track rib assembly and adjacent attach strap.
It is permitted to apply sealant to the underside of these parts to secure the sealant. Refer to Boeing
Service Bulletin 737-57A1358 APPENDIX G for example application of main track rib assembly attach
strap space sealant on the right wing engine fuel shutoff valve access panel.
(k) Do not apply parting agent to the surround structure of the engine fuel shutoff valve access panel.
(l) Frekote 710-NC is permitted to be used as a parting agent.
(m) If Frekote 710-NC is used as a parting agent, do as follows:
– Apply two coats to the surfaces of the engine fuel shutoff valve access panel which are in contact
with the surround structure. Apply parting agent to the access panel only. Allow 5 to 10 minutes be-
tween each application. Allow 20 minutes after the second application before closing the access
panel. Extend the application area of parting agent to be more than 2 inch larger than the fay surface
area to allow for the squeeze out. Parting agent can be applied to the entire surface of the engine
fuel shutoff valve access panel. Do not touch applied parting agent.
(n) Make a FiP gasket. Apply sealant smooth and flat at the fay surface of the engine fuel shutoff valve access
panel surround structure. Enough sealant should be applied to achieve continuous squeeze-out along
the edges of the panel. After the access panel has latched close, continue to press up on the panel with
the same force used to latch the panel. Continue this pressure for 15 seconds to allow excess sealant to
squeeze out fully. Do not press up with more force than required to latch the panel or voids will be created
in the FiP gasket and the fluid leak test will fail.
(o) After closing the engine fuel shutoff valve access panel, while the FiP gasket sealant is still wet, remove
the sealant from the spaces between the edges of both the access panel and surrounding structure, except
for the sealant at the aft edge of the engine fuel shutoff valve access panel. Allow the sealant to cure.
Refer to SOPM 20-50-19 as an accepted procedure.
(p) After the sealant has cured, cycle the engine fuel shutoff valve access panel to break it free from the
sealant. It is acceptable to use a skin wedge to break the panel free. After cycling the panel, it should
open without assistance. Make sure that the sealant bonds to the access panel surround structure and
not the access panel. Trim excess cured sealant from door structure as required.
(q) After sealant has cured and door has been re-opened, remove and apply new parting agent. Refer to
SOPM 20-50-19 as an accepted procedure. In lieu of subsequent re-applications of parting agent every
time the door is re-opened, petrolatum that meets VV-P-236 specification or Krytox 240AC can be applied
to the panel as a post-cure lubricant. If petrolatum is applied to the panel after the sealant has cured, it
must be wiped off with a lint-free rag leaving behind a thin film. If Krytox 240AC is used, it does not have
to be wiped off.
FIGURE 3: LEFT WING - ENGINE FUEL SHUTOFF VALVE ACCESS PANEL - FORM-IN-PLACE (FIP)
GASKET REPLACEMENT
(SHEET 4 OF 5)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: November 17, 2025
737-57A1358 RB
31 of 63
REQUIREMENTS BULLETIN 737-57A1358
ALERTALERT

### Page 32

More DataQtyIdentificationNameTaskStep
(r) Remove any sealant adhering to the access panel or excess sealant squeeze that extends into the panel
opening from the surround structure.
(s) The FiP gasket and sealant must be removed and applied again if the sealing surface on the surround
structure of the engine fuel shutoff valve access panel does not meet all the conditions that follow:
1. No structure is visible in the FiP gasket area.
2. All sealant is evenly distributed.
3. No sealant is added after the initial sealant application time expires.
4. Any small cavities or depressions in the sealing surface which are less than or equal to 1/4 inch
in width, and 1/8 inch in length, are permitted if the cavities or depressions do not extend across
the full width of the sealed surface and maintain a minimum sealing surface of 1/4 inch.
5. The outboard aft corner of the gasket area is sealed and attached to the flange of the main track
rib assembly and attach strap.
(t) Remove any excess FiP gasket sealant from the notch at the aft edge of the engine fuel shutoff valve
access panel and forward of the lower skin panel.
FIGURE 3: LEFT WING - ENGINE FUEL SHUTOFF VALVE ACCESS PANEL - FORM-IN-PLACE (FIP)
GASKET REPLACEMENT
(SHEET 5 OF 5)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: November 17, 2025
737-57A1358 RB
32 of 63
REQUIREMENTS BULLETIN 737-57A1358
ALERTALERT

### Page 33 (OCR)

REQUIREMENTS BULLETIN 737-57A1358
ALERT  ALERT
This Figure applies only to: Group 1.
SLAT STA
36.00
MAIN TRACK  SLAT STA  SEAL RIB
RIB ASSEMBLY  UPPER SKIN PANEL  36.00  ASSEMBLY
ATTACH 060U 24560U  STRAP  PANEL  LOWER SKIN
ENGINE FUEL SHUTOFF VALVE
ACCESS PANEL IS NOT SHOWN
APPLICATION AREA  FORM-IN-PLACE GASKET  (VIEW IN THE UP DIRECTION)
FORM-IN-PLACE GASKET AND  A-A
SEALANT APPLICATION AREA
FIGURE 4: RIGHT WING - ENGINE FUEL SHUTOFF VALVE ACCESS PANEL - FORM-IN-PLACE (FIP)
GASKET REPLACEMENT
(SHEET 1 OF 5)
Original Issue: November 17, 2025
Export Controlled ECCN: 9E991  737-57A1358 RB
See page 1 for details  33 of 63

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
