# Boeing Special Attention Requirements Bulletin 737-78-1106 RB: Revision 1

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2023-2235; AD 2025-04-03 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Special Attention Requirements Bulletin 737-78-1106 RB](https://openairdocs.org/service-documents/boeing/737-78-1106-rb.md)
- Title as filed: 737-78-1106 RB
- Pages: 118
- PDF: https://openairdocs.org/files/sha256/90/05/9005fdcdce6fdde3f182782087b63cb6f1ba876c7d3852cba873090d3a8fd747
- Page: https://openairdocs.org/service-documents/boeing/737-78-1106-rb/file/9005fdcdce6f

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Commercial 
Airplanes
737
Requirements Bulletin
SPECIAL ATTENTION
Number: 737-78-1106 RB
Original Issue: September 01, 2023
ATA System: 7811
SUBJECT: EXHAUST - Turbine Exhaust System - Engine Primary Exhaust Nozzle Change
EXPORT CONTROLLED - This technology or software is subject to the U.S. Export Administration Regulations
(EAR), (15 C.F.R. Parts 730-774). No authorization from the U.S. Department of Commerce is required for
export, re-export, in-country transfer, or access EXCEPT to country group E:1 or E:2 countries/persons per
Supp.1 to Part 740 of the EAR.
9E991ECCN:
Copyright © 2023 The Boeing Company
Treatment of this document and its content is governed by contract with Boeing. Rights to use this document
are licensed on a per aircraft basis and such rights may not be transferable. For more information, contact The
Boeing Company.
Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner,
BBJ, DC-8, DC-9, DC-10, KC-10, KC-46, KDC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8, Poseidon and
Boeing liveries are all trademarks owned by The Boeing Company; and no trademark license is granted in
connection with this document unless provided in writing by Boeing.
Original Issue: September 01, 2023
737-78-1106 RB
1 of 118
6.0

### Page 2

Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: September 01, 2023
737-78-1106 RB
2 of 118
REQUIREMENTS BULLETIN 737-78-1106
BLANK PAGE

### Page 3

Table of Contents
1. EFFECTIVITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
A. Airplanes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
B. Spares Affected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2. CONCURRENT REQUIREMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3. COMPLIANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4. APPROVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5. ACCOMPLISHMENT INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
A. General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
B. Work Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
FIGURE 2: PRIMARY EXHAUST NOZZLE - UPPER LEFT BRIDGE BRACKET - PREPARATION . . 21
FIGURE 3: PRIMARY EXHAUST NOZZLE - UPPER LEFT BRIDGE BRACKET INSTALLATION . . . 35
FIGURE 4: PRIMARY EXHAUST NOZZLE - UPPER RIGHT BRIDGE BRACKET - PREPARATION . 44
FIGURE 5: PRIMARY EXHAUST NOZZLE - UPPER RIGHT HAND BRIDGE BRACKET INSTALLATION
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
FIGURE 6: PRIMARY EXHAUST NOZZLE - LOWER LEFT HAND BRIDGE BRACKET - PREPARATION
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
FIGURE 7: PRIMARY EXHAUST NOZZLE - LOWER LEFT BRIDGE BRACKET INSTALLATION . . 81
FIGURE 8: PRIMARY EXHAUST NOZZLE - LOWER RIGHT BRIDGE BRACKET - PREPARATION . 90
FIGURE 9: PRIMARY EXHAUST NOZZLE - LOWER RIGHT BRIDGE BRACKET INSTALLATION . 104
FIGURE 11: ENGINE - PRIMARY EXHAUST NOZZLE - PARTIAL INSTALLATION . . . . . . . . . . 113
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: September 01, 2023
737-78-1106 RB
3 of 118
REQUIREMENTS BULLETIN 737-78-1106

### Page 4

Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: September 01, 2023
737-78-1106 RB
4 of 118
REQUIREMENTS BULLETIN 737-78-1106
BLANK PAGE

### Page 5

Commercial 
Airplanes
737
Requirements Bulletin
SPECIAL ATTENTION
Number: 737-78-1106 RB
Original Issue: September 01, 2023
ATA System: 7811
SUBJECT: EXHAUST - Turbine Exhaust System - Engine Primary Exhaust Nozzle Change
BOEING RECOMMENDS THAT EACH OPERATOR EXAMINE THIS DOCUMENT IMMEDIATELY. THIS IS
AN ENHANCED REQUIRED FOR COMPLIANCE DOCUMENT. THE BOEING PROCESSES USED TO CREATE
THE SERVICE BULLETIN (SB) AND THE REQUIREMENTS BULLETIN (RB) ENSURE THAT THE
INFORMATION BETWEEN "RC START" AND "RC END" IN THE SB ARE IDENTICAL TO THE INFORMATION
IN THE SAME SECTIONS (COMPLIANCE, WORK INSTRUCTIONS…) OF THE RB WHICH THE SB REFERS
TO AS THE RELATED DOCUMENT.
1. Effectivity
A. Airplanes
This bulletin is applicable to 737-600, 737-700, 737-700C, 737-800, 737-900, 737-900ER
Airplane(s), line number(s) 1-1244, 1246-1613, 1615-1809, 1811-1838, 1840-1884, 1886-1933,
1935-1978, 1980-1990, 1992-2079, 2081-2156, 2158-2231, 2233-2530, 2532-2598, 2600-2721,
2723-2813, 2815-2821, 2823-2930, 2932-3068, 3070, 3072-3188, 3190-3318, 3320-3323,
3325-3425, 3427-3521, 3523-3611, 3613-3701, 3703-3761 in 1 Group(s). Where the effectivity is
presented with hyphens between line numbers, the airplane applicability means "through" and
"inclusive", e.g. line numbers 1-9 means line numbers 1 through 9 inclusive.
The Variable Numbers and Group Information for the applicable airplanes is given below.
DESCRIPTIONCONFIGURATIONGROUP
737-600, 737-700, 737-700C, 737-800, 737-900, 737-900ER
Airplanes delivered without the Performance Improvement Package
(PIP)
- 1
Airplane Models:
737-600, 737-700, 737-700C, 737-800, 737-900, 737-900ER
GroupVariable Number
1YA001 - YA099
1YA101 - YA199
1YA201 - YA211
GroupVariable Number
1YA221
1YA231 - YA242
1YA251 - YA256
GroupVariable Number
1YA271 - YA272
1YA291
1YA301 - YA302
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: September 01, 2023
737-78-1106 RB
5 of 118

### Page 6

GroupVariable Number
1YA311 - YA314
1YA321 - YA323
1YA336 - YA345
1YA351
1YA356 - YA357
1YA366 - YA367
1YA371 - YA377
1YA501 - YA536
1YA541 - YA552
1YA571 - YA578
1YA601 - YA615
1YA621 - YA622
1YA626 - YA631
1YA635 - YA636
1YA641 - YA642
1YA645 - YA650
1YA656 - YA659
1YA666 - YA667
1YA671 - YA672
1YA681 - YA691
1YA701 - YA710
1YA721 - YA722
1YA731 - YA734
1YA751 - YA756
1YA801 - YA803
1YA809
1YA811 - YA814
1YA831 - YA835
1YA841 - YA862
1YA881 - YA882
1YA891 - YA892
1YA961 - YA978
1YB001 - YB006
GroupVariable Number
1YB101 - YB132
1YB151 - YB153
1YB156 - YB158
1YB161 - YB164
1YB171 - YB172
1YB181 - YB184
1YB201 - YB208
1YB271
1YB276
1YB301 - YB310
1YB371 - YB392
1YB501 - YB502
1YB521 - YB526
1YB541 - YB544
1YB551
1YB561 - YB598
1YB601 - YB635
1YB651
1YB656
1YB671 - YB672
1YB851 - YB863
1YB871 - YB874
1YB881 - YB893
1YB901 - YB903
1YB911
1YB961 - YB975
1YB981
1YB986 - YB998
1YC001 - YC030
1YC051 - YC084
1YC091 - YC095
1YC101 - YC104
1YC111 - YC113
GroupVariable Number
1YC121
1YC126 - YC127
1YC136 - YC141
1YC146 - YC147
1YC151 - YC156
1YC166 - YC171
1YC176 - YC179
1YC186 - YC190
1YC201 - YC203
1YC206 - YC207
1YC301 - YC305
1YC321 - YC387
1YC391 - YC394
1YC396
1YC401 - YC417
1YC421 - YC422
1YC426 - YC428
1YC436 - YC439
1YC441 - YC448
1YC451 - YC455
1YC459
1YC461 - YC467
1YC471 - YC499
1YC501 - YC526
1YC571 - YC583
1YC587 - YC589
1YC591 - YC593
1YC601 - YC655
1YC681 - YC696
1YC701 - YC715
1YC720 - YC725
1YC727 - YC752
1YC761 - YC770
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: September 01, 2023
737-78-1106 RB
6 of 118
REQUIREMENTS BULLETIN 737-78-1106

### Page 7

GroupVariable Number
1YC781 - YC793
1YC801 - YC892
1YC901 - YC907
1YC921 - YC922
1YC931 - YC932
1YC941 - YC951
1YC971 - YC978
1YC981 - YC983
1YD001 - YD007
1YD021 - YD025
1YD041 - YD057
1YD081 - YD084
1YD101 - YD117
1YD121 - YD126
1YD151 - YD159
1YD171 - YD172
1YD201 - YD203
1YD206 - YD209
1YD216 - YD219
1YD251 - YD254
1YD256 - YD257
1YD261
1YD301 - YD334
1YD391
1YD401 - YD410
1YD412 - YD417
1YD481 - YD485
1YD491 - YD499
1YD501 - YD512
1YD531 - YD535
1YD541 - YD547
1YD561 - YD564
1YD571 - YD572
GroupVariable Number
1YD591 - YD595
1YD601 - YD612
1YD651 - YD655
1YE001 - YE020
1YE051
1YE101 - YE109
1YE151 - YE157
1YE171 - YE172
1YE201 - YE206
1YE301 - YE305
1YE321 - YE326
1YE371 - YE383
1YF001 - YF011
1YF021 - YF049
1YF051 - YF067
1YF086 - YF087
1YF106 - YF107
1YF111 - YF114
1YF116 - YF119
1YF121 - YF130
1YF176 - YF178
1YF191 - YF192
1YF201 - YF276
1YF401 - YF402
1YF431 - YF432
1YF436 - YF437
1YF441 - YF442
1YF451 - YF460
1YF501 - YF599
1YF601 - YF621
1YF701 - YF707
1YF801 - YF805
1YF831 - YF832
GroupVariable Number
1YF836 - YF838
1YF901 - YF905
1YF921 - YF928
1YF951 - YF954
1YG001 - YG044
1YG061 - YG064
1YG066 - YG089
1YG091 - YG099
1YG101 - YG104
1YG111 - YG114
1YG116 - YG131
1YG501 - YG512
1YG601 - YG602
1YG701
1YH001 - YH012
1YH031 - YH055
1YH071 - YH080
1YH101 - YH132
1YH201 - YH202
1YH206 - YH207
1YH301 - YH306
1YH321 - YH322
1YH501 - YH507
1YH551
1YH601 - YH602
1YH611 - YH612
1YJ001 - YJ013
1YJ021
1YJ471 - YJ480
1YJ501 - YJ517
1YJ531 - YJ579
1YJ591 - YJ599
1YJ631 - YJ632
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: September 01, 2023
737-78-1106 RB
7 of 118
REQUIREMENTS BULLETIN 737-78-1106

### Page 8

GroupVariable Number
1YJ671 - YJ694
1YJ801 - YJ867
1YJ871 - YJ880
1YJ901 - YJ904
1YJ908 - YJ929
1YJ931 - YJ937
1YJ941 - YJ956
1YJ961
1YJ976 - YJ977
1YK001 - YK007
1YK101 - YK104
1YK111 - YK112
1YK121 - YK122
1YK131 - YK133
1YK136 - YK139
1YK141 - YK142
1YK146 - YK148
1YK151 - YK154
1YK161 - YK167
1YK171
1YK176 - YK177
1YK186
1YK191
1YK196
1YK201 - YK202
1YK301 - YK314
1YK321 - YK340
1YK361 - YK378
1YK401 - YK406
1YK426 - YK427
1YK431 - YK450
1YK456 - YK467
1YK471 - YK473
GroupVariable Number
1YK476
1YK480 - YK487
1YK491 - YK492
1YK495 - YK498
1YK511 - YK516
1YK521 - YK530
1YK551 - YK571
1YK576 - YK577
1YK580 - YK585
1YK601 - YK602
1YK606 - YK607
1YK611 - YK616
1YK621 - YK634
1YK641 - YK644
1YK651 - YK665
1YK671 - YK672
1YK676 - YK677
1YK681 - YK686
1YK691
1YK701 - YK713
1YK716 - YK719
1YK721 - YK741
1YK751 - YK770
1YK776 - YK778
1YK781 - YK785
1YK791 - YK792
1YK796 - YK797
1YK801 - YK899
1YK901 - YK912
1YK918 - YK919
1YK921 - YK929
1YK941 - YK997
1YL001 - YL005
GroupVariable Number
1YL011 - YL016
1YL021 - YL024
1YL051 - YL052
1YL056 - YL057
1YL061
1YL066 - YL069
1YL076 - YL077
1YL101 - YL137
1YL201 - YL230
1YL241 - YL242
1YL271 - YL272
1YL281 - YL284
1YL301 - YL303
1YL311 - YL314
1YL316 - YL321
1YL351 - YL353
1YL371 - YL374
1YL401
1YL421 - YL429
1YL431 - YL444
1YL461 - YL478
1YL501 - YL509
1YL531 - YL534
1YL541 - YL551
1YL561 - YL578
1YL591 - YL598
1YL601 - YL606
1YL611 - YL612
1YL616 - YL617
1YL621
1YL626
1YL631 - YL634
1YL636 - YL637
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: September 01, 2023
737-78-1106 RB
8 of 118
REQUIREMENTS BULLETIN 737-78-1106

### Page 9

GroupVariable Number
1YL661 - YL664
1YL676 - YL688
1YL691
1YL696 - YL697
1YL701 - YL707
1YL731
1YL751 - YL752
1YL756 - YL757
1YL761 - YL780
1YL796 - YL797
1YL801 - YL815
1YL901 - YL910
1YL921 - YL940
1YL951 - YL968
1YM101 - YM103
1YM201 - YM244
1YM251 - YM299
1YM301 - YM399
1YM401 - YM410
1YM471
1YM481 - YM484
1YM501 - YM515
1YM521 - YM522
1YM541
1YM551 - YM553
1YM571 - YM572
1YM581 - YM582
1YM591 - YM599
1YM631 - YM634
1YM641 - YM652
GroupVariable Number
1YM671 - YM674
1YM691 - YM699
1YM701 - YM710
1YM761 - YM765
1YM771 - YM775
1YN001 - YN016
1YN021 - YN024
1YN061
1YN071 - YN082
1YN091 - YN092
1YN101 - YN112
1YN121
1YN201 - YN202
1YN211 - YN219
1YN231 - YN236
1YN261
1YN501
1YN531 - YN534
1YN551
1YN601
1YN701
1YQ001 - YQ003
1YQ011 - YQ019
1YQ026 - YQ029
1YQ036 - YQ044
1YQ201 - YQ202
1YQ231
1YQ241 - YQ251
1YQ281
1YQ291 - YQ296
GroupVariable Number
1YQ301 - YQ302
1YQ401 - YQ403
1YQ451 - YQ453
1YR001 - YR012
1YR051 - YR055
1YR101 - YR102
1YR111 - YR116
1YR126 - YR129
1YR141 - YR142
1YR166 - YR172
1YR201 - YR204
1YR231 - YR244
1YR271 - YR276
1YR286
1YR291 - YR294
1YR296
1YR301 - YR308
1YR361
1YR401 - YR403
1YR421
1YR451 - YR452
1YR501 - YR503
1YR511 - YR512
1YR516
1YR601 - YR605
1YR651 - YR652
1YR701 - YR706
1YR801 - YR804
1YR851
--
B. Spares Affected
Examine your spares supply for the parts or components identified below. If any parts or components
are found, refer to Work Instructions for the recommended action.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: September 01, 2023
737-78-1106 RB
9 of 118
REQUIREMENTS BULLETIN 737-78-1106

### Page 10

Part Number
314A2610-1
314A2610-62
314A2610-68
2. CONCURRENT REQUIREMENTS
None.
3. COMPLIANCE
The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to this
Requirements Bulletin 737-78-1106 RB. The Airworthiness Directive will make the compliance tasks and
times given in Requirements Bulletin 737-78-1106 RB mandatory.
Accomplish the required action(s), based on the applicable condition in Tables 1 and 2, in accordance with
Accomplishment Instructions.
When more than one OPTION is given for a CONDITION, do only one of the OPTION numbers. When
more than one ACTION is given for a CONDITION number or an OPTION number, do all of the ACTION
numbers for that CONDITION number or OPTION number.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: September 01, 2023
737-78-1106 RB
10 of 118
REQUIREMENTS BULLETIN 737-78-1106

### Page 11

Table 1: Work Package 1 - Engine 1 - Primary Exhaust Nozzle Change
Repeat Inter-
val (Not to Ex-
ceed)
Boeing Recommend-
ed Compliance Time
ActionCondition
-Within 90 days after the
Original Issue date of
Requirements Bulletin
737-78-1106 RB, or
before further flight af-
ter accomplishing either
CONDITION 1 (OP-
TION 1), CONDITION
1 (OPTION 2), or CON-
DITION 2, whichever
occurs first.
(OPTION 1)(ACTION 1): Incorporate
737-600/700/700C/800/900/900ER Air-
worthiness Limitations (AWLs) document
D626A001-9-01 "SYSTEM AIRWORTHI-
NESS LIMITATION NO. 2 - FAN BLADE
OUT CONDITIONS" and "SYSTEM
AIRWORTHINESS LIMITATION NO. 3
- FAN BLADE OUT CONDITIONS" into
the operators' maintenance program.
All Airplanes
Before July 31, 2028.(OPTION 1)(ACTION 2): Do a mainte-
nance records check to find if the engine
has a primary exhaust nozzle with an
affected part number. (a)
Within 90 days after the
Original Issue date of
Requirements Bulletin
737-78-1106 RB, or
before further flight af-
ter accomplishing either
CONDITION 1 (OP-
TION 1), CONDITION
1 (OPTION 2), or CON-
DITION 2, whichever
occurs first.
(OPTION 2)(ACTION 1): Incorporate
737-600/700/700C/800/900/900ER Air-
worthiness Limitations (AWLs) document
D626A001-9-01 "SYSTEM AIRWORTHI-
NESS LIMITATION NO. 2 - FAN BLADE
OUT CONDITIONS" and "SYSTEM
AIRWORTHINESS LIMITATION NO. 3
- FAN BLADE OUT CONDITIONS" into
the operators' maintenance program.
Before July 31, 2028.(OPTION 2)(ACTION 2): Do an inspec-
tion of the engine to find if the engine
has a primary exhaust nozzle with an
affected part number. (a)
-Before July 31, 2028.(OPTION 1)(ACTION 1): Change affect-
ed primary exhaust nozzle. (a)
CONDITION 1: ANY PRIMA-
RY EXHAUST NOZZLE
FOUND WITH AN AFFECT-
ED PART NUMBER (OPTION 1)(ACTION 2): Install a 'ser-viceable' primary exhaust nozzle. (b)
(OPTION 2): Install a 'serviceable' prima-
ry exhaust nozzle. (b)
--No further action required.CONDITION 2: NO AF-
FECTED PRIMARY EX-
HAUST NOZZLE PART
NUMBER FOUND
(a) Affected primary exhaust nozzle part numbers are 314A2610-1, 314A2610-62 and 314A2610-68.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: September 01, 2023
737-78-1106 RB
11 of 118
REQUIREMENTS BULLETIN 737-78-1106

### Page 12

Table 1: Work Package 1 - Engine 1 - Primary Exhaust Nozzle Change
Repeat Inter-
val (Not to Ex-
ceed)
Boeing Recommend-
ed Compliance Time
ActionCondition
(b) A 'serviceable' primary exhaust nozzle is defined as one that has accomplished CONDITION 1 (OPTION
1)(ACTION 1) or CONDITION 3 (OPTION 1)(ACTION 1). Part numbers 314A2610-201, 314A2610-203,
or 314A2610-205 are acceptable 'serviceable' primary exhaust nozzles.
Table 2: Work Package 2 - Engine 2 - Primary Exhaust Nozzle Change
Repeat Inter-
val (Not to Ex-
ceed)
Boeing Recommend-
ed Compliance Time
ActionCondition
-Within 90 days after the
Original Issue date of
Requirements Bulletin
737-78-1106 RB, or
before further flight af-
ter accomplishing either
CONDITION 3 (OP-
TION 1), CONDITION
3 (OPTION 2), or CON-
DITION 4, whichever
occurs first.
(OPTION 1)(ACTION 1): Incorporate
737-600/700/700C/800/900/900ER Air-
worthiness Limitations (AWLs) document
D626A001-9-01 "SYSTEM AIRWORTHI-
NESS LIMITATION NO. 2 - FAN BLADE
OUT CONDITIONS" and "SYSTEM
AIRWORTHINESS LIMITATION NO. 3
- FAN BLADE OUT CONDITIONS" into
the operators' maintenance program.
All Airplanes
Before July 31, 2028.(OPTION 1)(ACTION 2): Do a mainte-
nance records check to find if the engine
has a primary exhaust nozzle with an
affected part number. (a)
Within 90 days after the
Original Issue date of
Requirements Bulletin
737-78-1106 RB, or
before further flight af-
ter accomplishing either
CONDITION 3 (OP-
TION 1), CONDITION
3 (OPTION 2), or CON-
DITION 4, whichever
occurs first.
(OPTION 2)(ACTION 1): Incorporate
737-600/700/700C/800/900/900ER Air-
worthiness Limitations (AWLs) document
D626A001-9-01 "SYSTEM AIRWORTHI-
NESS LIMITATION NO. 2 - FAN BLADE
OUT CONDITIONS" and "SYSTEM
AIRWORTHINESS LIMITATION NO. 3
- FAN BLADE OUT CONDITIONS" into
the operators' maintenance program.
Before July 31, 2028.(OPTION 2)(ACTION 2): Do an inspec-
tion of the engine to find if the engine
has a primary exhaust nozzle with an
affected part number. (a)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: September 01, 2023
737-78-1106 RB
12 of 118
REQUIREMENTS BULLETIN 737-78-1106

### Page 13

Table 2: Work Package 2 - Engine 2 - Primary Exhaust Nozzle Change
Repeat Inter-
val (Not to Ex-
ceed)
Boeing Recommend-
ed Compliance Time
ActionCondition
-Before July 31, 2028.(OPTION 1)(ACTION 1): Change affect-
ed primary exhaust nozzle. (a)
CONDITION 3: ANY PRIMA-
RY EXHAUST NOZZLE
FOUND WITH AN AFFECT-
ED PART NUMBER (OPTION 1)(ACTION 2): Install a 'ser-viceable' primary exhaust nozzle. (b)
(OPTION 2): Install a 'serviceable' prima-
ry exhaust nozzle. (b)
--No further action required.CONDITION 4: NO AF-
FECTED PRIMARY EX-
HAUST NOZZLE PART
NUMBER FOUND
(a) Affected primary exhaust nozzle part numbers are 314A2610-1, 314A2610-62 and 314A2610-68.
(b) A 'serviceable' primary exhaust nozzle is defined as one that has accomplished CONDITION 1 (OPTION
1)(ACTION 1) or CONDITION 3 (OPTION 1)(ACTION 1). Part numbers 314A2610-201, 314A2610-203,
or 314A2610-205 are acceptable 'serviceable' primary exhaust nozzles.
4. APPROVAL
This Requirements Bulletin was examined by the Federal Aviation Administration (FAA). The changes
specified in this document comply with the applicable regulations and are FAA approved for all airplanes
listed in this Requirements Bulletin effectivity. This document and its approval were based on the airplane
in its original Boeing delivery configuration or as modified by other Boeing changes.
If an airplane has a non-Boeing modification or repair that affects a component or system also affected by
this Requirements Bulletin, the operator is responsible for obtaining appropriate regulatory agency approval
before incorporating this Requirements Bulletin.
Accomplishment of this Requirements Bulletin meets the requirements of 737-600/700/700C/800/900/900ER
Airworthiness Limitations (AWLs) document D626A001-9-01 "SYSTEM AIRWORTHINESS LIMITATION
NO. 3 - FAN BLADE OUT CONDITIONS".
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: September 01, 2023
737-78-1106 RB
13 of 118
REQUIREMENTS BULLETIN 737-78-1106

### Page 14

Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: September 01, 2023
737-78-1106 RB
14 of 118
REQUIREMENTS BULLETIN 737-78-1106
BLANK PAGE

### Page 15

5.    ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL INFORMATION
NOTE: 1. This is an Enhanced Required for Compliance document. There will be a separate
Service Bulletin (SB) and a separate Requirements Bulletin (RB). If an RB is mandated
by an Airworthiness Directive (AD), then all applicable requirements specified in the
RB must be done. For the related SB, some locations are marked RC Start and RC
End to identify the requirements that are restated from the RB. For the related SB,
the areas between RC Start and RC End, including sub-steps and any figures
identified between RC Start and RC End, must be done to comply with the AD.
Therefore, an Alternative Method of Compliance (AMOC) is required for any deviations
to steps between RC Start and RC End, including substeps and identified figures.
For the related SB, the steps not between RC Start and RC End may be deviated
from using accepted methods in accordance with the operator's maintenance or
inspection program without obtaining approval of an AMOC; this is provided that the
steps between RC Start and RC End, including sub-steps and identified figures, can
still be done as specified, and the airplane can be put back in an airworthy condition.
Figures not required for compliance are omitted from the RB.
2. This is an Enhanced Required for Compliance document. The Boeing processes
used to create the Service Bulletin (SB) and the Requirements Bulletin (RB) ensure
that the information between "RC Start" and "RC End" in the SB are identical to the
information in the same sections (Compliance, Work Instructions...) of the RB which
the SB refers to as the related document.
3. The compliance times for the actions in WORK INSTRUCTIONS are in Compliance.
4. Unless shown differently, these dimensions and tolerances are used:
– Linear dimensions are in inches
– Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus
or minus 0.03 inch
– Tolerance on rivet and bolt edge margin is plus or minus 0.05 inch
– Angular tolerance is plus or minus 2 degrees
– Hole dimensions for standard solid rivets and fasteners are in Structural Repair
Manual (SRM) Chapter 51
– Torque Values:
— Values for structural fasteners are given in
737-600/700/700C/800/900/900ER Structural Repair Manual, Chapter 51.
— Values for engine maintenance tasks are included in Chapter 70 of
737-600/700/800/900 Aircraft Maintenance Manual (AMM).
— Non-standard torque values for maintenance tasks are included in the
applicable installation step.
5. These work instructions refer to procedures included in other Boeing documents.
When the words "refer to" are used and the operator has an accepted alternative
procedure, the accepted alternative procedure can be used. When the words "in
accordance with" are included in the instruction, the procedure in the Boeing document
must be used.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: September 01, 2023
737-78-1106 RB
15 of 118
REQUIREMENTS BULLETIN 737-78-1106

### Page 16

6. Where the work instructions include installation of a kept part, a new or serviceable
part with the same part number can be installed as an alternative to the kept part.
7. If it is necessary to remove more parts for access, you can remove those parts. If
you can get access without removing identified parts, it is not necessary to remove
all of the identified parts. Jacking and shoring limitations must be observed.
8. A Detailed Inspection is defined as: An intensive examination of a specific item,
installation or assembly to detect damage, failure or irregularity. This could include
tactile assessment in which a component or assembly can be checked for
tightness/security. Available lighting is normally supplemented with a direct source
of good lighting at an intensity deemed appropriate. Inspection aids such as mirrors
and magnifying lenses may be necessary. Surface cleaning and elaborate access
procedures may be required.
9. When more than one OPTION is given for a CONDITION, do only one of the OPTION
numbers. When more than one ACTION is given for a CONDITION or an OPTION,
do all of the ACTION numbers for that CONDITION or OPTION.
10. The instructions in Work Instructions and the figures can include operation of tools
or test equipment. Boeing Engineering Tool Drawings, the Illustrated Tool and
Equipment Manual, and the Special Tool and Ground Handling Drawing Index contain
data on versions of the tools or test equipment that you can use. It is permitted to
use replaced tools. It is not permitted to use superseded tools.
B. WORK INSTRUCTIONS
Actions Required for Compliance
1. Requirements:
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: September 01, 2023
737-78-1106 RB
16 of 118
REQUIREMENTS BULLETIN 737-78-1106

### Page 17

Table 1: Work Package 1 - Engine 1 - Primary Exhaust Nozzle Change
Refer to the listed proce-
dures in SB 737-78-1106
Original Issue or later ap-
proved revision as an ac-
cepted procedure
Method of
Compliance
ActionCondition
--(OPTION 1)(ACTION 1): Incor-
porate 737-
600/700/700C/800/900/900ER
Airworthiness Limitations
(AWLs) document D626A001-
9-01 "SYSTEM AIRWORTHI-
NESS LIMITATION NO. 2 -
FAN BLADE OUT CONDI-
TIONS" and "SYSTEM AIR-
WORTHINESS LIMITATION
NO. 3 - FAN BLADE OUT
CONDITIONS" into the opera-
tors' maintenance program.
All Airplanes
(OPTION 1)(ACTION 2): Do
a maintenance records check
to find if the engine has a pri-
mary exhaust nozzle with an
affected part number. (a)
(OPTION 2)(ACTION 1): Incor-
porate 737-
600/700/700C/800/900/900ER
Airworthiness Limitations
(AWLs) document D626A001-
9-01 "SYSTEM AIRWORTHI-
NESS LIMITATION NO. 2 -
FAN BLADE OUT CONDI-
TIONS" and "SYSTEM AIR-
WORTHINESS LIMITATION
NO. 3 - FAN BLADE OUT
CONDITIONS" into the opera-
tors' maintenance program.
PART 1: ENGINE - OPEN
ACCESS
-(OPTION 2)(ACTION 2): Do
an inspection of the engine to
find if the engine has a prima-
ry exhaust nozzle with an af-
fected part number. (a)
PART 5: ENGINE - CLOSE
ACCESS
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: September 01, 2023
737-78-1106 RB
17 of 118
REQUIREMENTS BULLETIN 737-78-1106

### Page 18

Table 1: Work Package 1 - Engine 1 - Primary Exhaust Nozzle Change
Refer to the listed proce-
dures in SB 737-78-1106
Original Issue or later ap-
proved revision as an ac-
cepted procedure
Method of
Compliance
ActionCondition
PART 2: ENGINE - PRIMARY
EXHAUST NOZZLE RE-
MOVAL
-(OPTION 1)(ACTION 1):
Change affected primary ex-
haust nozzle. (a)
CONDITION 1: ANY
PRIMARY EXHAUST
NOZZLE FOUND WITH
AN AFFECTED PART
NUMBER -FIGURE 2
FIGURE 3
FIGURE 4
FIGURE 5
FIGURE 6
FIGURE 7
FIGURE 8
FIGURE 9
PART 3: ENGINE - PRIMARY
EXHAUST NOZZLE - PART
MARKING
-
PART 4: ENGINE - PRIMARY
EXHAUST NOZZLE INSTAL-
LATION
-(OPTION 1)(ACTION 2): In-
stall a 'serviceable' primary
exhaust nozzle. (b)
-FIGURE 11
PART 5: ENGINE - CLOSE
ACCESS
-
PART 4: ENGINE - PRIMARY
EXHAUST NOZZLE INSTAL-
LATION
-(OPTION 2): Install a 'service-
able' primary exhaust nozzle.
(b)
-FIGURE 11
PART 5: ENGINE - CLOSE
ACCESS
-
--No further action required.CONDITION 2: NO AF-
FECTED PRIMARY
EXHAUST NOZZLE
PART NUMBER
FOUND
(a) Affected primary exhaust nozzle part numbers are 314A2610-1, 314A2610-62 and 314A2610-68.
(b) A 'serviceable' primary exhaust nozzle is defined as one that has accomplished CONDITION 1
(OPTION 1)(ACTION 1) or CONDITION 3 (OPTION 1)(ACTION 1). Part numbers 314A2610-201,
314A2610-203, or 314A2610-205 are acceptable 'serviceable' primary exhaust nozzles.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: September 01, 2023
737-78-1106 RB
18 of 118
REQUIREMENTS BULLETIN 737-78-1106

### Page 19

Table 2: Work Package 2 - Engine 2 - Primary Exhaust Nozzle Change
Refer to the listed proce-
dures in SB 737-78-1106
Original Issue or later ap-
proved revision as an ac-
cepted procedure
Method of
Compliance
ActionCondition
--(OPTION 1)(ACTION 1): Incor-
porate 737-
600/700/700C/800/900/900ER
Airworthiness Limitations
(AWLs) document D626A001-
9-01 "SYSTEM AIRWORTHI-
NESS LIMITATION NO. 2 -
FAN BLADE OUT CONDI-
TIONS" and "SYSTEM AIR-
WORTHINESS LIMITATION
NO. 3 - FAN BLADE OUT
CONDITIONS" into the opera-
tors' maintenance program.
All Airplanes
(OPTION 1)(ACTION 2): Do
a maintenance records check
to find if the engine has a pri-
mary exhaust nozzle with an
affected part number. (a)
(OPTION 2)(ACTION 1): Incor-
porate 737-
600/700/700C/800/900/900ER
Airworthiness Limitations
(AWLs) document D626A001-
9-01 "SYSTEM AIRWORTHI-
NESS LIMITATION NO. 2 -
FAN BLADE OUT CONDI-
TIONS" and "SYSTEM AIR-
WORTHINESS LIMITATION
NO. 3 - FAN BLADE OUT
CONDITIONS" into the opera-
tors' maintenance program.
PART 1: ENGINE - OPEN
ACCESS
-(OPTION 2)(ACTION 2): Do
an inspection of the engine to
find if the engine has a prima-
ry exhaust nozzle with an af-
fected part number. (a)
PART 5: ENGINE - CLOSE
ACCESS
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: September 01, 2023
737-78-1106 RB
19 of 118
REQUIREMENTS BULLETIN 737-78-1106

### Page 20

Table 2: Work Package 2 - Engine 2 - Primary Exhaust Nozzle Change
Refer to the listed proce-
dures in SB 737-78-1106
Original Issue or later ap-
proved revision as an ac-
cepted procedure
Method of
Compliance
ActionCondition
PART 2: ENGINE - PRIMARY
EXHAUST NOZZLE RE-
MOVAL
-(OPTION 1)(ACTION 1):
Change affected primary ex-
haust nozzle. (a)
CONDITION 3: ANY
PRIMARY EXHAUST
NOZZLE FOUND WITH
AN AFFECTED PART
NUMBER -FIGURE 2
FIGURE 3
FIGURE 4
FIGURE 5
FIGURE 6
FIGURE 7
FIGURE 8
FIGURE 9
PART 3: ENGINE - PRIMARY
EXHAUST NOZZLE - PART
MARKING
-
PART 4: ENGINE - PRIMARY
EXHAUST NOZZLE INSTAL-
LATION
-(OPTION 1)(ACTION 2): In-
stall a 'serviceable' primary
exhaust nozzle. (b)
-FIGURE 11
PART 5: ENGINE - CLOSE
ACCESS
-
PART 4: ENGINE - PRIMARY
EXHAUST NOZZLE INSTAL-
LATION
-(OPTION 2): Install a 'service-
able' primary exhaust nozzle.
(b)
-FIGURE 11
PART 5: ENGINE - CLOSE
ACCESS
-
--No further action required.CONDITION 4: NO AF-
FECTED PRIMARY
EXHAUST NOZZLE
PART NUMBER
FOUND
(a) Affected primary exhaust nozzle part numbers are 314A2610-1, 314A2610-62 and 314A2610-68.
(b) A 'serviceable' primary exhaust nozzle is defined as one that has accomplished CONDITION 1
(OPTION 1)(ACTION 1) or CONDITION 3 (OPTION 1)(ACTION 1). Part numbers 314A2610-201,
314A2610-203, or 314A2610-205 are acceptable 'serviceable' primary exhaust nozzles.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: September 01, 2023
737-78-1106 RB
20 of 118
REQUIREMENTS BULLETIN 737-78-1106

### Page 21 (OCR)

REQUIREMENTS BULLETIN 737-78-1106
C  AND
ALIGNMENT PIN HOLE #1
NOTCH
1 HOLE #5
1 HOLE #6
1 HOLE #7
1 HOLE #8
1 HOLE #9
ATTACH RING  1 HOLE #10
A-A  3019050
FIGURE 2: PRIMARY EXHAUST NOZZLE - UPPER LEFT BRIDGE BRACKET - PREPARATION
(SHEET 1 OF 14)
Original Issue: September 01, 2023
737-78-1106 RB
Export Controlled ECCN: 9E991
See page 1 for details  21 of 118

### Page 22

FIGURE 2: PRIMARY EXHAUST NOZZLE - UPPER LEFT BRIDGE BRACKET - PREPARATION
(SHEET 2 OF 14)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: September 01, 2023
737-78-1106 RB
22 of 118
REQUIREMENTS BULLETIN 737-78-1106

### Page 23

FIGURE 2: PRIMARY EXHAUST NOZZLE - UPPER LEFT BRIDGE BRACKET - PREPARATION
(SHEET 3 OF 14)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: September 01, 2023
737-78-1106 RB
23 of 118
REQUIREMENTS BULLETIN 737-78-1106

### Page 24 (OCR)

REQUIREMENTS BULLETIN 737-78-1106
LOCATOR 'INDEX' PIN OR (2 14)  (2) WINGNUTS  14) LOCATOR 'INDEX' PIN OR
DIAMOND 'INDEX' PIN  HOLE #8  HOLE #7  DIAMOND 'INDEX' PIN
ATTACH RING
- ASSEMBL
B  BRIDG
BRACKE
ID~  • HAT STIFFENER
INDEX PIN  STRAIGHT EDGES  TYPICAL  3024529
FIGURE 2: PRIMARY EXHAUST NOZZLE - UPPER LEFT BRIDGE BRACKET - PREPARATION
(SHEET 4 OF 14)
Original Issue: September 01, 2023
737-78-1106 RB
Export Controlled ECCN: 9E991
See page 1 for details  24 of 118

### Page 25 (OCR)

REQUIREMENTS BULLETIN 737-78-1106
BRIDGE BRACKET
/ CUTOUT
HAT STIFFENER •
CENTERLINE OF
HAT STIFFENER
AND BRIDGE
BRACKET CUTOUT
C-C
BRIDGE BRACKET
CUTOUT
• HAT STIFFENER
CENTERLINE OF
HAT STIFFENER
AND BRIDGE
BRACKET CUTOUT
D-D  3024531
FIGURE 2: PRIMARY EXHAUST NOZZLE - UPPER LEFT BRIDGE BRACKET - PREPARATION
(SHEET 5 OF 14)
Original Issue: September 01, 2023
737-78-1106 RB
Export Controlled ECCN: 9E991
See page 1 for details  25 of 118

### Page 26 (OCR)

REQUIREMENTS BULLETIN 737-78-1106
C-CLAMPS (6) 9)  14  SHIM 1A€OU14
12 LOCATIONS) ®30 DA  WINGNUT
DRILL ASSEMBLY (14
BRIDGE BRACKET 14
FORWARD FILLER 1
CLAMP PIN
SPACER
WINGNUT
DO 014
CLAMP PIN
(2 LOCATIONS)
ICAL  (12 14
CLAMP PIN
(2 LOCATIONS)
10(14
AFT FILLER 1
• FILLER(S) NECESSARY IF DISTANCE BETWEEN BRIDGE BRACKET  3024523
AND PRIMARY EXHAUST NOZZLE IS MORE THAN 0.005 INCH
FIGURE 2: PRIMARY EXHAUST NOZZLE - UPPER LEFT BRIDGE BRACKET - PREPARATION
(SHEET 6 OF 14)
Original Issue: September 01, 2023
Export Controlled ECCN: 9E991  737-78-1106 RB
See page 1 for details  26 of 118

### Page 27

FIGURE 2: PRIMARY EXHAUST NOZZLE - UPPER LEFT BRIDGE BRACKET - PREPARATION
(SHEET 7 OF 14)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: September 01, 2023
737-78-1106 RB
27 of 118
REQUIREMENTS BULLETIN 737-78-1106

### Page 28

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
More DataQtyIdentificationNameTaskStep
Use the notch in the
attach ring as a refer-
ence to help locate
holes #5 thru #10.
6-HOLEIdentify1
Clean holes #5 thru
#10 in the attach
ring. Refer to SOPM
20-30-03 as an ac-
cepted procedure.
6-HOLEClean
(a) --PROTECTIONApply
- 12MIT314A2610UPR LH CLAMP BLKPut
- 22MIT314A2610L-PINPut
(b) 1314A2650-1BRIDGE BRACKET,
UPPER LH
Put 2
(b) 12MIT314A2610UPR LH DRILL ASSYPut
(b) 22MIT314A2610INDEX PINPut
(b) 22MIT314A2610WINGNUTPut
(c) 1314A2650-1BRIDGE BRACKET,
UPPER LH
Align
(d) --DISTANCEMeasure
(e) -2MIT314A2610SHIMPut
(f)(g) 22MIT314A2610WINGNUTTighten
MAKE SURE THAT THE CORRECT HOLES IN THE ATTACH RING ARE USED FOR
THE LOCATION OF THE DRILL ASSEMBLY AND BRIDGE BRACKET. USE OF AN IN-
CORRECTLY LOCATED DRILL ASSEMBLY COULD CAUSE THE PRIMARY EXHAUST
NOZZLE TO BECOME UNSERVICEABLE.
CAUTION
(h)(i) --DISTANCEMeasure3
(j) 22MIT314A2610WINGNUTLoosen4
(j) -2MIT314A2610SHIMRelease
(j)(l) -314A2670-7,
314A2670-17,
314A2670-27
FILLERPut 5
(j)(e) -2MIT314A2610SHIMPut
(j)(f) 22MIT314A2610WINGNUTTighten
FIGURE 2: PRIMARY EXHAUST NOZZLE - UPPER LEFT BRIDGE BRACKET - PREPARATION
(SHEET 8 OF 14)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: September 01, 2023
737-78-1106 RB
28 of 118
REQUIREMENTS BULLETIN 737-78-1106

### Page 29

More DataQtyIdentificationNameTaskStep
(m) 22MIT314A2610C-CLAMPPut 6
22MIT314A2610C-CLAMPTighten
At hole location '1'
identified for the for-
ward row on the Drill
Assembly. (n)
1-HOLEDrill 7
Remove drill debris.
Refer to SOPM 20-
30-03 as an accept-
ed procedure.
1-HOLEClean
(o) 12MIT314A2610CLAMP PINPut
(o) 12MIT314A2610SPACERPut
(o) 12MIT314A2610WINGNUTPut
- 12MIT314A2610WINGNUTTighten
At hole location '2'
identified for the for-
ward row on the Drill
Assembly. (n)
1-HOLEDrill
Remove drill debris.
Refer to SOPM 20-
30-03 as an accept-
ed procedure.
1-HOLEClean
(o) 12MIT314A2610CLAMP PINPut
(o) 12MIT314A2610SPACERPut
(o) 12MIT314A2610WINGNUTPut
- 12MIT314A2610WINGNUTTighten
At hole locations '3'
and '4' identified for
the forward row on
the Drill Assembly.
(n)
2-HOLEDrill 8
Remove drill debris.
Refer to SOPM 20-
30-03 as an accept-
ed procedure.
2-HOLEClean
FIGURE 2: PRIMARY EXHAUST NOZZLE - UPPER LEFT BRIDGE BRACKET - PREPARATION
(SHEET 9 OF 14)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: September 01, 2023
737-78-1106 RB
29 of 118
REQUIREMENTS BULLETIN 737-78-1106

### Page 30

More DataQtyIdentificationNameTaskStep
(k)(p) 22MIT314A2610CLAMP PINRelease9
(k)(p) 22MIT314A2610SPACERRelease
At forward row.
(k)(p)
22MIT314A2610WINGNUTRelease
(k)(p) 22MIT314A2610C-CLAMPRelease
At attach ring. (k)(p)22MIT314A2610WINGNUTLoosen
(k)(p) -2MIT314A2610SHIMRelease
(j)(k)(p)1314A2670-7,
314A2670-17,
314A2670-27
FILLERRelease
(k)(l)(p)-314A2670-7,
314A2670-17,
314A2670-27
FILLERPut 10
(e)(p) -2MIT314A2610SHIMPut
(p)(q)22MIT314A2610CLAMP PINPut
(p)(q)22MIT314A2610SPACERPut
(p)(q)22MIT314A2610WINGNUTPut
Maximum quantity
given. (f)(p)
42MIT314A2610WINGNUTTighten
(m)(p)22MIT314A2610C-CLAMPPut 11
(p) 22MIT314A2610C-CLAMPTighten
FIGURE 2: PRIMARY EXHAUST NOZZLE - UPPER LEFT BRIDGE BRACKET - PREPARATION
(SHEET 10 OF 14)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: September 01, 2023
737-78-1106 RB
30 of 118
REQUIREMENTS BULLETIN 737-78-1106

### Page 31

More DataQtyIdentificationNameTaskStep
At hole location '1'
identified for the aft
row on the Drill As-
sembly. (n)
1-HOLEDrill 12
Remove drill debris.
Refer to SOPM 20-
30-03 as an accept-
ed procedure.
1-HOLEClean
(o) 12MIT314A2610CLAMP PINPut
(o) 12MIT314A2610SPACERPut
(o) 12MIT314A2610WINGNUTPut
- 12MIT314A2610WINGNUTTighten
At hole location '2'
identified for the aft
row on the Drill As-
sembly. (n)
1-HOLEDrill
Remove drill debris.
Refer to SOPM 20-
30-03 as an accept-
ed procedure.
1-HOLEClean
(o) 12MIT314A2610CLAMP PINPut
(o) 12MIT314A2610SPACERPut
(o) 12MIT314A2610WINGNUTPut
- 12MIT314A2610WINGNUTTighten
At hole location '3'
and '4' identified for
the aft row on the
Drill Assembly. (n)
2-HOLEDrill 13
Remove drill debris.
Refer to SOPM 20-
30-03 as an accept-
ed procedure.
2-HOLEClean
FIGURE 2: PRIMARY EXHAUST NOZZLE - UPPER LEFT BRIDGE BRACKET - PREPARATION
(SHEET 11 OF 14)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: September 01, 2023
737-78-1106 RB
31 of 118
REQUIREMENTS BULLETIN 737-78-1106

### Page 32

More DataQtyIdentificationNameTaskStep
- 22MIT314A2610C-CLAMPRelease14
Maximum quantity
given.
62MIT314A2610WINGNUTRelease
Maximum quantity
given.
42MIT314A2610SPACERRelease
Maximum quantity
given.
42MIT314A2610CLAMP PINRelease
- -2MIT314A2610SHIMRelease
- 22MIT314A2610INDEX PINRelease
- 12MIT314A2610UPR LH DRILL ASSYRelease
- 22MIT314A2610L-PINRelease
- 12MIT314A2610UPR LH CLAMP BLKRelease
- 1314A2650-1BRIDGE BRACKET,
UPPER LH
Release
(k) -314A2670-7,
314A2670-17,
314A2670-27
FILLERRelease
Remove drill debris.
Refer to SOPM 20-
30-03 as an accept-
ed procedure.
1314A2650-1BRIDGE BRACKET,
UPPER LH
Clean
Remove drill debris.
Refer to SOPM 20-
30-03 as an accept-
ed procedure.(k)
-314A2670-7,
314A2670-17,
314A2670-27
FILLERClean
Deburr all drilled
holes in the primary
exhaust nozzle,
Filler(s) (Filler(s) are
not necessary if the
distance between
the Bridge Bracket
and the Primary Ex-
haust Nozzle is
0.005 or less) and
the Bridge Bracket.
--HOLEDeburr15
(r) --HOLEInspect
FIGURE 2: PRIMARY EXHAUST NOZZLE - UPPER LEFT BRIDGE BRACKET - PREPARATION
(SHEET 12 OF 14)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: September 01, 2023
737-78-1106 RB
32 of 118
REQUIREMENTS BULLETIN 737-78-1106

### Page 33

More DataQtyIdentificationNameTaskStep
Remove drill debris
from the exhaust
nozzle surface. Re-
fer to SOPM 20-30-
03 as an accepted
procedure.
--PRIMARY EXHAUST
NOZZLE
Clean16
(a) Put or pack protection (polythene sheet(s), for example) between the primary exhaust nozzle external
surface and the fairing skin to prevent debris that could fall into the space during the work of this Figure.
(b) Hold the Bridge Bracket and Drill Assembly together loosely and put the diamond 'index' pin into one of
the middle holes of the Bridge Bracket through the attach ring. Put the locator 'index' pin in the other
middle hole of the Bridge Bracket. The straight edge of the head of each 'index' pin is a feature to prevent
interference with the radius in the Bridge Bracket. Make sure that the head of each 'index' pin is against
the Bridge Bracket and hand-tighten the wingnuts. Keep the chosen index pin locations the same during
this work of this Figure.
(c) Adjust the location of the Drill Assembly in the forward or aft direction to align the centerline of the Bridge
Bracket cutout and the centerline of the hat stiffener.
(d) Measure the distance between the forward face of the Drill Assembly and the aft face of the attach ring
to find the shim thickness necessary to fill the distance.
(e) Select and put the thickness of shim(s) necessary to fill the distance between the Drill Assembly and the
attach ring.
(f) Hand-tighten the wingnuts to tightly hold the Drill Assembly and Bridge Bracket in the correct position.
(g) Make sure the Bridge Bracket is centered around the hat stiffener. Adjust shims as needed.
(h) Measure the distance between the Bridge Bracket and the external surface of the primary exhaust nozzle
at each side of the Bridge Bracket. Make sure the difference between the two measured distances 0.015
inches or less.
(i) Measure the distance between the external surface of the primary exhaust nozzle and the Bridge Bracket
at the forward and aft locations identified. If each distance is 0.005 inches or less, no Filler is necessary.
One or more Fillers, part numbers 314A2670-7, 314A2670-17 and 314A2670-27, can be used to fill the
distance(s). If a measured distance is not the same as a thickness of a Filler (or combination of Fillers),
use the nearest Filler thickness. Total Filler thickness at each location must not be more than 0.060 inch.
If there is a difference between the measured distance on each side of the Bracket, calculate and use
the average of the two measurements. Although, a difference of more than 0.015 inches between the
measured distances on each side of the Bracket is not permitted.
(j) This Task or Step is only applicable if one or more Fillers are necessary at the forward location.
(k) This Task or Step is only applicable if one or more Fillers are necessary at the aft location.
(l) Put the Filler(s) parallel to the hat stiffener, positioned centrally between the Exhaust Nozzle surface and
the Bridge Bracket, and with clearance from the hat stiffener radius. The ends of the Filler(s) will not be
parallel with the sides of the Bridge Bracket. Tape, or equivalent, can be used to temporarily hold the
Filler(s) in the correct position.
(m) Use two C-Clamps, each positioned at the "CLAMP AREA" identified on the Drill Assembly, to hold the
Bridge Bracket and the Filler(s) in the correct position.
FIGURE 2: PRIMARY EXHAUST NOZZLE - UPPER LEFT BRIDGE BRACKET - PREPARATION
(SHEET 13 OF 14)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: September 01, 2023
737-78-1106 RB
33 of 118
REQUIREMENTS BULLETIN 737-78-1106

### Page 34

More DataQtyIdentificationNameTaskStep
(n) Make sure the power feed drill is correctly prepared and use it to drill a 0.279-0.291 inch diameter hole
through the Bridge Bracket, the Filler(s) (Filler(s) are not necessary if the distance between the Bridge
Bracket and the Primary Exhaust Nozzle is 0.005 inch or less) and the primary exhaust nozzle.
(o) Install a Clamp Pin, Spacer and Wingnut for the hole of location '1' identified on the Drill Assembly, after
it is drilled. Install one more Clamp Pin, Spacer and Wingnut for the hole of location '2' identified on the
Drill Assembly after it is drilled.
(p) If Fillers are not necessary at the forward and aft locations, the aft row of holes in the Bridge Bracket can
be drilled immediately after the forward row of holes, in accordance with the drilling sequence identified
on the Drill Assembly.
(q) Install Clamp Pins, Spacers and Wingnuts for the holes of location '1' and '2' identified for the forward row
on the Drill Assembly to give additional clamp-up force and to provide alignment.
(r) Do a Detailed Inspection of all drilled holes for their dimension and quality in accordance with 737-600
SRM 51-40-05, 737-700 SRM 51-40-05, 737-700CONV SRM 51-40-05, 737-800 SRM 51-40-05, 737-
900 SRM 51-40-05 or 737-900ER SRM 51-40-05. Make sure that each hole diameter is 0.279-0.291
inches. Make sure that the distance from the center of the holes drilled in the forward row to the edge of
the cutout in the Bridge Bracket is 0.328-0.358 inches. Make sure that the distance from the center of the
holes drilled in the aft row to the edge of the cutout in the Bridge Bracket is 0.395-0.425 inches.
FIGURE 2: PRIMARY EXHAUST NOZZLE - UPPER LEFT BRIDGE BRACKET - PREPARATION
(SHEET 14 OF 14)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: September 01, 2023
737-78-1106 RB
34 of 118
REQUIREMENTS BULLETIN 737-78-1106

### Page 35 (OCR)

REQUIREMENTS BULLETIN 737-78-1106
A AND B
WINGNUT
ATTACH RING
J (2 LOCATIONS)  INDEX PIN
2) 4 LOCATIONS
CLAMP PIN
BRIDGE  (4 LOCATIONS)
BRACKET
4 LOCATIONS (2
) FORWARD FILLER
(4 LOCATIONS) 13)  SPACER
(4 LOCATIONS) 3  WINGNUT  AFT FILLER
D
TYPICAL
• FILLER(S) NECESSARY IF DISTANCE BETWEEN BRIDGE BRACKET  3019055
AND PRIMARY EXHAUST NOZZLE IS MORE THAN 0.005 INCH
FIGURE 3: PRIMARY EXHAUST NOZZLE - UPPER LEFT BRIDGE BRACKET INSTALLATION
(SHEET 1 OF 9)
Original Issue: September 01, 2023
737-78-1106 RB
Export Controlled ECCN: 9E991
See page 1 for details  35 of 118

### Page 36 (OCR)

REQUIREMENTS BULLETIN 737-78-1106
WINGNUTS
INDEX PINS  ATTACH RING
BRIDGE BRACKET~
4 LOCATIONS
TYPICAL
3033200
FIGURE 3: PRIMARY EXHAUST NOZZLE - UPPER LEFT BRIDGE BRACKET INSTALLATION
(SHEET 2 OF 9)
Original Issue: September 01, 2023
737-78-1106 RB
Export Controlled ECCN: 9E991
36 of 118

### Page 37 (OCR)

REQUIREMENTS BULLETIN 737-78-1106
HOLE #8  HOLE #7
WINGNUT
(2 LOCATIONS)  XE LOCATI  (2 LOCATIONS)
• ATTACH RING
B  B
(2) 4 LOCATIONS
TORQUE
SEQUENCE
HAT
STIFFENER
TYPICAL  4) 4 LOCATIONS
A-A
INDEX PIN  STRAIGHT EDGES  TYPICAL  3019059
B-B
FIGURE 3: PRIMARY EXHAUST NOZZLE - UPPER LEFT BRIDGE BRACKET INSTALLATION
(SHEET 3 OF 9)
Original Issue: September 01, 2023
737-78-1106 RB
Export Controlled ECCN: 9E991
See page 1 for details  37 of 118

### Page 38

FIGURE 3: PRIMARY EXHAUST NOZZLE - UPPER LEFT BRIDGE BRACKET INSTALLATION
(SHEET 4 OF 9)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: September 01, 2023
737-78-1106 RB
38 of 118
REQUIREMENTS BULLETIN 737-78-1106

### Page 39

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
More DataQtyIdentificationNameTaskStep
At the forward loca-
tion. (a)
-314A2670-7,
314A2670-17,
314A2670-27
FILLERInstall (New)1
At the aft location.
(a)
-314A2670-7,
314A2670-17,
314A2670-27
FILLERInstall (New)
- 1314A2650-1BRIDGE BRACKET,
UPPER LH
Install (New)
At hole locations 5,
6, 7 and 8 identified
in view A-A. The
hole numbers are
not related to the
fastener installation
sequence.
42MIT314A2610CLAMP PINPut
At hole locations 5,
6, 7 and 8 identified
in view A-A. The
hole numbers are
not related to the
fastener installation
sequence.
42MIT314A2610SPACERPut
Hand-tighten the
Wingnuts at hole lo-
cations 5, 6, 7 and 8
identified in view A-
A. The hole numbers
are not related to the
fastener installation
sequence.
42MIT314A2610WINGNUTPut
- 22MIT314A2610INDEX PINPut
- 22MIT314A2610WINGNUTPut
Hand-tighten the
Wingnuts.
62MIT314A2610WINGNUTTighten
FIGURE 3: PRIMARY EXHAUST NOZZLE - UPPER LEFT BRIDGE BRACKET INSTALLATION
(SHEET 5 OF 9)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: September 01, 2023
737-78-1106 RB
39 of 118
REQUIREMENTS BULLETIN 737-78-1106

### Page 40

More DataQtyIdentificationNameTaskStep
Install the bolts at
hole locations 1, 2,
3 and 4 identified in
view A-A. The hole
numbers are not re-
lated to the fastener
installation se-
quence.
4BACB30YL8K5BOLT, HEX DRIVEInstall (New)2
Install the washers
at hole locations 1,
2, 3 and 4 identified
in view A-A. The
hole numbers are
not related to the
fastener installation
sequence.
4BACW10BP4ACUWASHERInstall (New)
Install the nuts at
hole locations 1, 2,
3 and 4 identified in
view A-A. The hole
numbers are not re-
lated to the fastener
installation se-
quence.
4BACN11CC4UNUTInstall (New)
Torque the nuts at
hole locations 1, 2,
3 and 4, in the se-
quence specified in
view A-A. (b)
4BACN11CC4UNUTTorque
FIGURE 3: PRIMARY EXHAUST NOZZLE - UPPER LEFT BRIDGE BRACKET INSTALLATION
(SHEET 6 OF 9)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: September 01, 2023
737-78-1106 RB
40 of 118
REQUIREMENTS BULLETIN 737-78-1106

### Page 41

More DataQtyIdentificationNameTaskStep
At hole locations 5,
6, 7 and 8 identified
in view A-A. The
hole numbers are
not related to the
fastener release se-
quence.
42MIT314A2610CLAMP PINRelease3
At hole locations 5,
6, 7 and 8 identified
in view A-A. The
hole numbers are
not related to the
fastener release se-
quence.
42MIT314A2610SPACERRelease
At hole locations 5,
6, 7 and 8 identified
in view A-A. The
hole numbers are
not related to the
fastener release se-
quence.
42MIT314A2610WINGNUTRelease
FIGURE 3: PRIMARY EXHAUST NOZZLE - UPPER LEFT BRIDGE BRACKET INSTALLATION
(SHEET 7 OF 9)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: September 01, 2023
737-78-1106 RB
41 of 118
REQUIREMENTS BULLETIN 737-78-1106

### Page 42

More DataQtyIdentificationNameTaskStep
Install the bolts at
hole locations 5, 6,
7 and 8 identified in
view A-A. The hole
numbers are not re-
lated to the fastener
installation se-
quence.
4BACB30YL8K5BOLT, HEX DRIVEInstall (New)4
Install the washers
at hole locations 5,
6, 7 and 8 identified
in view A-A. The
hole numbers are
not related to the
fastener installation
sequence.
4BACW10BP4ACUWASHERInstall (New)
Install the nuts at
hole locations 5, 6,
7 and 8 identified in
view A-A. The hole
numbers are not re-
lated to the fastener
installation se-
quence.
4BACN11CC4UNUTInstall (New)
Torque the nuts at
hole locations 5, 6,
7 and 8, in the se-
quence specified in
view A-A. (b)
4BACN11CC4UNUTTorque
(c) --DISTANCEMeasure5
- 22MIT314A2610INDEX PINRelease6
- 22MIT314A2610WINGNUTRelease
- --PROTECTIONRemove7
Remove any remain-
ing drill debris. Refer
to SOPM 20-30-03
as an accepted pro-
cedure.
--PRIMARY EXHAUST
NOZZLE
Clean
(a) Install the Filler(s) selected at preparation. Filler(s) are not necessary if the distance between the Bridge
Bracket and the Primary Exhaust Nozzle is 0.005 inch or less.
(b) Torque to 75 in-lbs (set point torque).
FIGURE 3: PRIMARY EXHAUST NOZZLE - UPPER LEFT BRIDGE BRACKET INSTALLATION
(SHEET 8 OF 9)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: September 01, 2023
737-78-1106 RB
42 of 118
REQUIREMENTS BULLETIN 737-78-1106

### Page 43

More DataQtyIdentificationNameTaskStep
(c) Make sure that the distance between the forward end of the Bridge Bracket and the aft side of the engine
attach ring is 1.091-1.391 inches.
FIGURE 3: PRIMARY EXHAUST NOZZLE - UPPER LEFT BRIDGE BRACKET INSTALLATION
(SHEET 9 OF 9)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: September 01, 2023
737-78-1106 RB
43 of 118
REQUIREMENTS BULLETIN 737-78-1106

### Page 44 (OCR)

REQUIREMENTS BULLETIN 737-78-1106
C AND D
ALIGNMENT PIN
HOLE #1 NOTCH
HOLE #5 1
HOLE #9 (1
ATTACH RING
HOLE #101
A-A  3019060
FIGURE 4: PRIMARY EXHAUST NOZZLE - UPPER RIGHT BRIDGE BRACKET - PREPARATION
(SHEET 1 OF 14)
Original Issue: September 01, 2023
Export Controlled ECCN: 9E991  737-78-1106 RB  44 of 118

### Page 45

FIGURE 4: PRIMARY EXHAUST NOZZLE - UPPER RIGHT BRIDGE BRACKET - PREPARATION
(SHEET 2 OF 14)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: September 01, 2023
737-78-1106 RB
45 of 118
REQUIREMENTS BULLETIN 737-78-1106

### Page 46

FIGURE 4: PRIMARY EXHAUST NOZZLE - UPPER RIGHT BRIDGE BRACKET - PREPARATION
(SHEET 3 OF 14)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: September 01, 2023
737-78-1106 RB
46 of 118
REQUIREMENTS BULLETIN 737-78-1106

### Page 47 (OCR)

REQUIREMENTS BULLETIN 737-78-1106
LOCATOR 'INDEX PIN OR 2) 14  2) WINGNUTS  2 14 LOCATOR 'INDEX PIN OR
DIAMOND 'INDEX' PIN  HOLE #7  HOLE #8  DIAMOND 'INDEX' PIN
• ATTACH RING
• DRIL
•ASSEMBL
• BRIDG
ASSEMBL
• HAT STIFFENER
C
INDEX PIN  STRAIGHT EDGES
TYPICAL  3019064
B-B
FIGURE 4: PRIMARY EXHAUST NOZZLE - UPPER RIGHT BRIDGE BRACKET - PREPARATION
(SHEET 4 OF 14)
Original Issue: September 01, 2023
737-78-1106 RB
Export Controlled ECCN: 9E991
See page 1 for details  47 of 118

### Page 48 (OCR)

REQUIREMENTS BULLETIN 737-78-1106C
BRIDGE BRACKET
/ CUTOUT
HAT STIFFENER ~
CENTERLINE OF
HAT STIFFENER
AND BRIDGE
BRACKET CUTOUT
C-C
BRIDGE BRACKET
CUTOUT
• HAT STIFFENER
CENTERLINE OF
- C
D-D  3019076
FIGURE 4: PRIMARY EXHAUST NOZZLE - UPPER RIGHT BRIDGE BRACKET - PREPARATION
(SHEET 5 OF 14)
Original Issue: September 01, 2023
Export Controlled ECCN: 9E991  737-78-1106 RB
See page 1 for details  48 of 118

### Page 49 (OCR)

REQUIREMENTS BULLETIN 737-78-1106
C-CLAMPS 6OU 14  SHIM 14€O014
Y NOCATIONS, ®3OOD  WINGNUT
DRILL ASSEMBLY (14
BRIDGE BRACKET (14
FORWARD FILLER 1
CLAMP PIN
SPACER
WINGNUT
D0014
CLAMP PIN
(2 LOCATIONS)
TYPICAL  12 14)
D  CLAMP PIN
(2 LOCATIONS)
AFT FILLER I
> FILLER(S) NECESSARY IF DISTANCE BETWEEN BRIDGE BRACKET  3028905
AND PRIMARY EXHAUST NOZZLE IS MORE THAN 0.005 INCH
FIGURE 4: PRIMARY EXHAUST NOZZLE - UPPER RIGHT BRIDGE BRACKET - PREPARATION
(SHEET 6 OF 14)
Original Issue: September 01, 2023
737-78-1106 RB
Export Controlled ECCN: 9E991
See page 1 for details  49 of 118

### Page 50

FIGURE 4: PRIMARY EXHAUST NOZZLE - UPPER RIGHT BRIDGE BRACKET - PREPARATION
(SHEET 7 OF 14)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: September 01, 2023
737-78-1106 RB
50 of 118
REQUIREMENTS BULLETIN 737-78-1106

### Page 51

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
More DataQtyIdentificationNameTaskStep
Use the notch in the
attach ring as a refer-
ence to help locate
holes #5 thru #10.
6-HOLEIdentify1
Clean holes #5 thru
#10 in the attach
ring. Refer to SOPM
20-30-03 as an ac-
cepted procedure.
6-HOLEClean
(a) --PROTECTIONApply
- 12MIT314A2610UPR RH CLAMP BLKPut
- 22MIT314A2610L-PINPut
(b) 1314A2650-2BRIDGE BRACKET,
UPPER RH
Put 2
(b) 12MIT314A2610UPR RH DRILL ASSYPut
(b) 22MIT314A2610INDEX PINPut
(b) 22MIT314A2610WINGNUTPut
(c) 1314A2650-2BRIDGE BRACKET,
UPPER RH
Align
(d) --DISTANCEMeasure
(e) -2MIT314A2610SHIMPut
(f)(g) 22MIT314A2610WINGNUTTighten
MAKE SURE THAT THE CORRECT HOLES IN THE ATTACH RING ARE USED FOR
THE LOCATION OF THE DRILL ASSEMBLY AND BRIDGE BRACKET. USE OF AN IN-
CORRECTLY LOCATED DRILL ASSEMBLY COULD CAUSE THE PRIMARY EXHAUST
NOZZLE TO BECOME UNSERVICEABLE.
CAUTION
(h)(i) --DISTANCEMeasure3
(j) 22MIT314A2610WINGNUTLoosen4
(j) -2MIT314A2610SHIMRelease
(j)(l) -314A2670-7,
314A2670-17,
314A2670-27
FILLERPut 5
(j)(e) -2MIT314A2610SHIMPut
(j)(f) 22MIT314A2610WINGNUTTighten
FIGURE 4: PRIMARY EXHAUST NOZZLE - UPPER RIGHT BRIDGE BRACKET - PREPARATION
(SHEET 8 OF 14)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: September 01, 2023
737-78-1106 RB
51 of 118
REQUIREMENTS BULLETIN 737-78-1106

### Page 52

More DataQtyIdentificationNameTaskStep
(m) 22MIT314A2610C-CLAMPPut 6
22MIT314A2610C-CLAMPTighten
At hole location '1'
identified for the for-
ward row on the Drill
Assembly. (n)
1-HOLEDrill 7
Remove drill debris.
Refer to SOPM 20-
30-03 as an accept-
ed procedure.
1-HOLEClean
(o) 12MIT314A2610CLAMP PINPut
(o) 12MIT314A2610SPACERPut
(o) 12MIT314A2610WINGNUTPut
- 12MIT314A2610WINGNUTTighten
At hole location '2'
identified for the for-
ward row on the Drill
Assembly. (n)
1-HOLEDrill
Remove drill debris.
Refer to SOPM 20-
30-03 as an accept-
ed procedure.
1-HOLEClean
(o) 12MIT314A2610CLAMP PINPut
(o) 12MIT314A2610SPACERPut
(o) 12MIT314A2610WINGNUTPut
- 12MIT314A2610WINGNUTTighten
At hole locations '3'
and '4' identified for
the forward row on
the Drill Assembly.
(n)
2-HOLEDrill 8
Remove drill debris.
Refer to SOPM 20-
30-03 as an accept-
ed procedure.
2-HOLEClean
FIGURE 4: PRIMARY EXHAUST NOZZLE - UPPER RIGHT BRIDGE BRACKET - PREPARATION
(SHEET 9 OF 14)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: September 01, 2023
737-78-1106 RB
52 of 118
REQUIREMENTS BULLETIN 737-78-1106

### Page 53

More DataQtyIdentificationNameTaskStep
(k)(p) 22MIT314A2610CLAMP PINRelease9
(k)(p) 22MIT314A2610SPACERRelease
At forward row.
(k)(p)
22MIT314A2610WINGNUTRelease
(k)(p) 22MIT314A2610C-CLAMPRelease
At attach ring. (k)(p)22MIT314A2610WINGNUTLoosen
(k)(p) -2MIT314A2610SHIMRelease
(j)(k)(p)1314A2670-7,
314A2670-17,
314A2670-27
FILLERRelease
(k)(l)(p)-314A2670-7,
314A2670-17,
314A2670-27
FILLERPut 10
(e)(p) -2MIT314A2610SHIMPut
(p)(q)22MIT314A2610CLAMP PINPut
(p)(q)22MIT314A2610SPACERPut
(p)(q)22MIT314A2610WINGNUTPut
Maximum quantity
given. (f)(p)
42MIT314A2610WINGNUTTighten
(m)(p)22MIT314A2610C-CLAMPPut 11
(p) 22MIT314A2610C-CLAMPTighten
FIGURE 4: PRIMARY EXHAUST NOZZLE - UPPER RIGHT BRIDGE BRACKET - PREPARATION
(SHEET 10 OF 14)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: September 01, 2023
737-78-1106 RB
53 of 118
REQUIREMENTS BULLETIN 737-78-1106

### Page 54

More DataQtyIdentificationNameTaskStep
At hole location '1'
identified for the aft
row on the Drill As-
sembly. (n)
1-HOLEDrill 12
Remove drill debris.
Refer to SOPM 20-
30-03 as an accept-
ed procedure.
1-HOLEClean
(o) 12MIT314A2610CLAMP PINPut
(o) 12MIT314A2610SPACERPut
(o) 12MIT314A2610WINGNUTPut
- 12MIT314A2610WINGNUTTighten
At hole location '2'
identified for the aft
row on the Drill As-
sembly. (n)
1-HOLEDrill
Remove drill debris.
Refer to SOPM 20-
30-03 as an accept-
ed procedure.
1-HOLEClean
(o) 12MIT314A2610CLAMP PINPut
(o) 12MIT314A2610SPACERPut
(o) 12MIT314A2610WINGNUTPut
- 12MIT314A2610WINGNUTTighten
At hole location '3'
and '4' identified for
the aft row on the
Drill Assembly. (n)
2-HOLEDrill 13
Remove drill debris.
Refer to SOPM 20-
30-03 as an accept-
ed procedure.
2-HOLEClean
FIGURE 4: PRIMARY EXHAUST NOZZLE - UPPER RIGHT BRIDGE BRACKET - PREPARATION
(SHEET 11 OF 14)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: September 01, 2023
737-78-1106 RB
54 of 118
REQUIREMENTS BULLETIN 737-78-1106

### Page 55

More DataQtyIdentificationNameTaskStep
- 22MIT314A2610C-CLAMPRelease14
Maximum quantity
given.
62MIT314A2610WINGNUTRelease
Maximum quantity
given.
42MIT314A2610SPACERRelease
Maximum quantity
given.
42MIT314A2610CLAMP PINRelease
- -2MIT314A2610SHIMRelease
- 22MIT314A2610INDEX PINRelease
- 12MIT314A2610UPR RH DRILL ASSYRelease
- 22MIT314A2610L-PINRelease
- 12MIT314A2610UPR RH CLAMP BLKRelease
- 1314A2650-2BRIDGE BRACKET,
UPPER RH
Release
(k) -314A2670-7,
314A2670-17,
314A2670-27
FILLERRelease
Remove drill debris.
Refer to SOPM 20-
30-03 as an accept-
ed procedure.
1314A2650-2BRIDGE BRACKET,
UPPER RH
Clean
Remove drill debris.
Refer to SOPM 20-
30-03 as an accept-
ed procedure.(k)
-314A2670-7,
314A2670-17,
314A2670-27
FILLERClean
Deburr all drilled
holes in the primary
exhaust nozzle,
Filler(s) (Filler(s) are
not necessary if the
distance between
the Bridge Bracket
and the Primary Ex-
haust Nozzle is
0.005 or less) and
the Bridge Bracket.
--HOLEDeburr15
(r) --HOLEInspect
FIGURE 4: PRIMARY EXHAUST NOZZLE - UPPER RIGHT BRIDGE BRACKET - PREPARATION
(SHEET 12 OF 14)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: September 01, 2023
737-78-1106 RB
55 of 118
REQUIREMENTS BULLETIN 737-78-1106

### Page 56

More DataQtyIdentificationNameTaskStep
Remove drill debris
from the exhaust
nozzle surface. Re-
fer to SOPM 20-30-
03 as an accepted
procedure.
--PRIMARY EXHAUST
NOZZLE
Clean16
(a) Put or pack protection (polythene sheet(s), for example) between the primary exhaust nozzle external
surface and the fairing skin to prevent debris that could fall into the space during the work of this Figure.
(b) Hold the Bridge Bracket and Drill Assembly together loosely and put the diamond 'index' pin into one of
the middle holes of the Bridge Bracket through the attach ring. Put the locator 'index' pin in the other
middle hole of the Bridge Bracket. The straight edge of the head of each 'index' pin is a feature to prevent
interference with the radius in the Bridge Bracket. Make sure that the head of each 'index' pin is against
the Bridge Bracket and hand-tighten the wingnuts. Keep the chosen index pin locations the same during
this work of this Figure.
(c) Adjust the location of the Drill Assembly in the forward or aft direction to align the centerline of the Bridge
Bracket cutout and the centerline of the hat stiffener.
(d) Measure the distance between the forward face of the Drill Assembly and the aft face of the attach ring
to find the shim thickness necessary to fill the distance.
(e) Select and put the thickness of shim(s) necessary to fill the distance between the Drill Assembly and the
attach ring.
(f) Hand-tighten the wingnuts to tightly hold the Drill Assembly and Bridge Bracket in the correct position.
(g) Make sure the Bridge Bracket is centered around the hat stiffener. Adjust shims as needed.
(h) Measure the distance between the Bridge Bracket and the external surface of the primary exhaust nozzle
at each side of the Bridge Bracket. Make sure the difference between the two measured distances 0.015
inches or less.
(i) Measure the distance between the external surface of the primary exhaust nozzle and the Bridge Bracket
at the forward and aft locations identified. If each distance is 0.005 inches or less, no Filler is necessary.
One or more Fillers, part numbers 314A2670-7, 314A2670-17 and 314A2670-27, can be used to fill the
distance(s). If a measured distance is not the same as a thickness of a Filler (or combination of Fillers),
use the nearest Filler thickness. Total Filler thickness at each location must not be more than 0.060 inch.
If there is a difference between the measured distance on each side of the Bracket, calculate and use
the average of the two measurements. Although, a difference of more than 0.015 inches between the
measured distances on each side of the Bracket is not permitted.
(j) This Task or Step is only applicable if one or more Fillers are necessary at the forward location.
(k) This Task or Step is only applicable if one or more Fillers are necessary at the aft location.
(l) Put the Filler(s) parallel to the hat stiffener, positioned centrally between the Exhaust Nozzle surface and
the Bridge Bracket, and with clearance from the hat stiffener radius. The ends of the Filler(s) will not be
parallel with the sides of the Bridge Bracket. Tape, or equivalent, can be used to temporarily hold the
Filler(s) in the correct position.
(m) Use two C-Clamps, each positioned at the "CLAMP AREA" identified on the Drill Assembly, to hold the
Bridge Bracket and the Filler(s) in the correct position.
FIGURE 4: PRIMARY EXHAUST NOZZLE - UPPER RIGHT BRIDGE BRACKET - PREPARATION
(SHEET 13 OF 14)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: September 01, 2023
737-78-1106 RB
56 of 118
REQUIREMENTS BULLETIN 737-78-1106

### Page 57

More DataQtyIdentificationNameTaskStep
(n) Make sure the power feed drill is correctly prepared and use it to drill a 0.279-0.291 inch diameter hole
through the Bridge Bracket, the Filler(s) (Filler(s) are not necessary if the distance between the Bridge
Bracket and the Primary Exhaust Nozzle is 0.005 inch or less) and the primary exhaust nozzle.
(o) Install a Clamp Pin, Spacer and Wingnut for the hole of location '1' identified on the Drill Assembly, after
it is drilled. Install one more Clamp Pin, Spacer and Wingnut for the hole of location '2' identified on the
Drill Assembly after it is drilled.
(p) If Fillers are not necessary at the forward and aft locations, the aft row of holes in the Bridge Bracket can
be drilled immediately after the forward row of holes, in accordance with the drilling sequence identified
on the Drill Assembly.
(q) Install Clamp Pins, Spacers and Wingnuts for the holes of location '1' and '2' identified for the forward row
on the Drill Assembly to give additional clamp-up force and to provide alignment.
(r) Do a Detailed Inspection of all drilled holes for their dimension and quality in accordance with 737-600
SRM 51-40-05, 737-700 SRM 51-40-05, 737-700CONV SRM 51-40-05, 737-800 SRM 51-40-05, 737-
900 SRM 51-40-05 or 737-900ER SRM 51-40-05. Make sure that each hole diameter is 0.279-0.291
inches. Make sure that the distance from the center of the holes drilled in the forward row to the edge of
the cutout in the Bridge Bracket is 0.328-0.358 inches. Make sure that the distance from the center of the
holes drilled in the aft row to the edge of the cutout in the Bridge Bracket is 0.395-0.425 inches.
FIGURE 4: PRIMARY EXHAUST NOZZLE - UPPER RIGHT BRIDGE BRACKET - PREPARATION
(SHEET 14 OF 14)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: September 01, 2023
737-78-1106 RB
57 of 118
REQUIREMENTS BULLETIN 737-78-1106

### Page 58 (OCR)

REQUIREMENTS BULLETIN 737-78-1106
A AND B
E LOCATIONS ®  WINGNUT
ATTACH RING
1 (2 LOCATIONS)  INDEX PIN
2) 4 LOCATIONS
CLAMP PIN
BRIDGE  (4 LOCATIONS)
BRACKET
4 LOCATIONS 2
1 FORWARD FILLER
(4 LOCATIONS) 3  SPACER
(4 LOCATIONS) 3  WINGNUT  AFT FILLER
TYPICAL
FILLERS) NECESSARY IF DISTANCE BETWEEN BRIDGE BRACKET  3019088
AND PRIMARY EXHAUST NOZZLE IS MORE THAN 0.005 INCH
FIGURE 5: PRIMARY EXHAUST NOZZLE - UPPER RIGHT HAND BRIDGE BRACKET INSTALLATION
(SHEET 1 OF 9)
Original Issue: September 01, 2023
737-78-1106 RB
Export Controlled ECCN: 9E991
See page 1 for details  58 of 118

### Page 59 (OCR)

REQUIREMENTS BULLETIN 737-78-1106
WINGNUTS
INDEX PINS  ATTACH RING
BRIDGE BRACKET~
4 LOCATIONS 4
TYPICAL
3033204
FIGURE 5: PRIMARY EXHAUST NOZZLE - UPPER RIGHT HAND BRIDGE BRACKET INSTALLATION
(SHEET 2 OF 9)
Original Issue: September 01, 2023
737-78-1106 RB
Export Controlled ECCN: 9E991
See page 1 for details  59 of 118

### Page 60 (OCR)

REQUIREMENTS BULLETIN 737-78-1106
HOLE #7  HOLE #8
(2 LOCATIONS) U€  WINGNUT
0O LOCATIONS)
• ATTACH RING
B  B
(2 4 LOCATIONS
TORQUE
SEQUENCE •
HAT
STIFFENER
TYPICAL  4) 4 LOCATIONS
A-A
STRAIGHT EDGES  INDEX PIN  TYPICAL  3031616
B-B
FIGURE 5: PRIMARY EXHAUST NOZZLE - UPPER RIGHT HAND BRIDGE BRACKET INSTALLATION
(SHEET 3 OF 9)
Original Issue: September 01, 2023
737-78-1106 RB
Export Controlled ECCN: 9E991
See page 1 for details  60 of 118

The text continues at https://openairdocs.org/service-documents/boeing/737-78-1106-rb/file/9005fdcdce6f.md?from=61

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
