# Boeing Alert Requirements Bulletin 747-21A2577 RB: 747-21A2577 RB-00--

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2020-0848; AD 2021-07-09 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Alert Requirements Bulletin 747-21A2577 RB](https://openairdocs.org/service-documents/boeing/747-21a2577-rb.md)
- Title as filed: 747-21A2577 RB-00--
- Pages: 33
- PDF: https://openairdocs.org/files/sha256/bf/6e/bf6eef5a41994f60c4e3643fa1a6506107c917a6055fd313cdd45a6a7c35f588
- Page: https://openairdocs.org/service-documents/boeing/747-21a2577-rb/file/bf6eef5a4199

## Text

Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Commercial 
Airplanes
747
Requirements Bulletin
ALERT
Number: 747-21A2577 RB
Original Issue: February 18, 2020
ATA System: 2161
SUBJECT: AIR CONDITIONING - Zone Temperature Control System - Trim Air Diffuser Duct
Inspection / Replacement
Export of this technology is controlled under the United States Export Administration Regulations (EAR) (15
CFR 300-774). An export license may be required before it is used for development, production or use by foreign
persons from specific countries. The controller of this data has the individual responsibility to abide by all export
laws.
9E991ECCN:
Copyright © 2020 Boeing.
Unpublished Work. All Rights Reserved.
Treatment of this document and its content is governed by contract with Boeing. Rights to use this document
are licensed on a per aircraft basis and such rights may not be transferable. For more information, contact The
Boeing Company.
Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner,
BBJ, DC-8, DC-9, DC-10, KC-10, KC-46, KDC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8, Poseidon and
Boeing liveries are all trademarks owned by The Boeing Company; and no trademark license is granted in
connection with this document unless provided in writing by Boeing.
Original Issue: February 18, 2020
747-21A2577 RB
1 of 33
5.0

### Page 2

Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 18, 2020
747-21A2577 RB
2 of 33
REQUIREMENTS BULLETIN 747-21A2577
ALERTALERT
BLANK PAGE

### Page 3

Table of Contents
1. EFFECTIVITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
A. Airplanes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
B. Spares Affected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2. CONCURRENT REQUIREMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3. COMPLIANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4. APPROVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
5. ACCOMPLISHMENT INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
A. General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
B. Work Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
APPENDIX A: ORIGINAL FIBERGLASS FABRIC MATERIAL TADD ASSEMBLY PART NUMBERS . . . 31
APPENDIX B: HIGH TEMPERATURE COMPOSITE MATERIAL TADD ASSEMBLY PART NUMBERS . 33
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 18, 2020
747-21A2577 RB
3 of 33
REQUIREMENTS BULLETIN 747-21A2577
ALERTALERT

### Page 4

Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 18, 2020
747-21A2577 RB
4 of 33
REQUIREMENTS BULLETIN 747-21A2577
ALERTALERT
BLANK PAGE

### Page 5

Commercial 
Airplanes
747
Requirements Bulletin
ALERT
Number: 747-21A2577 RB
Original Issue: February 18, 2020
ATA System: 2161
SUBJECT: AIR CONDITIONING - Zone Temperature Control System - Trim Air Diffuser Duct
Inspection / Replacement
THIS DOCUMENT IS SENT TO THE OPERATORS OF RECORD OF THE AIRPLANES SHOWN IN
PARAGRAPH 1.A., EFFECTIVITY. IF AN AIRPLANE HAS BEEN LEASED OR SOLD, SEND THIS DOCUMENT
TO THE NEW OPERATOR. IF APPLICABLE SPARES HAVE BEEN SOLD, SEND THIS DOCUMENT TO THE
NEW OWNER. THIS IS AN ENHANCED REQUIRED FOR COMPLIANCE DOCUMENT. THE BOEING
PROCESSES USED TO CREATE THE SERVICE BULLETIN (SB) AND THE REQUIREMENTS BULLETIN
(RB) ENSURE THAT THE INFORMATION BETWEEN "RC START" AND "RC END" IN THE SB ARE IDENTICAL
TO THE INFORMATION IN THE SAME SECTIONS (COMPLIANCE, WORK INSTRUCTIONS…) OF THE RB
WHICH THE SB REFERS TO AS THE RELATED DOCUMENT.
1. Effectivity
A. Airplanes
This bulletin is applicable to 747-100, 747-100B, 747-100B SUD, 747-200B, 747-200C, 747-200F,
747-300, 747-400, 747-400D, 747-400F, 747SP, 747SR Airplane(s), line number(s) 1-1419 in 2
Group(s). Where the effectivity is presented with hyphens between line numbers, the airplane
applicability means "through" and "inclusive", e.g. line numbers 1-9 means line numbers 1 through
9 inclusive.
Refer to APPENDIX A for the list of Original Fiberglass Fabric Material TADD assembly part
numbers. Refer to APPENDIX B for the list of High Temperature Composite Material TADD
assembly part numbers.
DESCRIPTIONCONFIGURATIONGROUP
747-100, 747-100B, 747-100B SUD, 747-200B, 747-200C, 747-200F,
747-300, 747-400, 747-400D, 747-400F, 747SP, 747SR Airplanes
with any Original Fiberglass Fabric Material TADD installed or have
replaced with any High Temperature Composite Material TADD
-1
Airplanes with any Original Fiberglass Fabric Material TADD installed1
Airplanes that have replaced any Original Fiberglass Fabric Material
TADD with any High Temperature Composite Material TADD
2
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 18, 2020
747-21A2577 RB
5 of 33

### Page 6

DESCRIPTIONCONFIGURATIONGROUP
747-400 and 747-400F Airplanes delivered with High Temperature
Composite Material TADD
-2
Airplane Models:
747-100, 747-100B, 747-100B SUD, 747-200B, 747-200C, 747-200F, 747-300, 747-400, 747-400D,
747-400F, 747SP, 747SR
GroupVariable Number
1RA001 - RA034
1RA101 - RA115
1RA161 - RA164
1RA201 - RA203
1RA216 - RA217
1RA245 - RA246
1RA251 - RA266
1RA301 - RA318
1RA351 - RA360
1RA369 - RA373
1RA401 - RA418
1RA501 - RA502
1RA521 - RA528
1RA532 - RA548
1RA551 - RA552
1RA559 - RA561
1RA581 - RA582
1RA585
1RA601 - RA602
1RA631 - RA635
1RA651 - RA652
1RA671 - RA677
1RA701 - RA702
1RA721 - RA731
1RA741 - RA745
GroupVariable Number
1RA749 - RA750
1RA761 - RA762
1RA781 - RA784
1RA901 - RA916
1RB001 - RB016
1RB041 - RB044
1RB071 - RB075
1RB101 - RB102
1RB411 - RB413
1RB421
1RB601 - RB607
1RB681 - RB697
1RB711
1RB721 - RB723
1RB741 - RB748
1RD001 - RD004
1RD021 - RD022
1RD041 - RD059
1RD071 - RD072
1RD081 - RD083
1RD091 - RD092
1RD101 - RD104
1RD121 - RD127
1RD131 - RD144
1RD166 - RD167
GroupVariable Number
1RD171 - RD172
1RD181 - RD183
1RD201 - RD204
1RD221 - RD227
1RD231 - RD235
1RD241 - RD243
1RD251 - RD262
1RD271 - RD272
1RD291 - RD292
1RD301 - RD302
1RD311
1RD351 - RD358
1RD361 - RD366
1RD381 - RD383
1RD411 - RD414
1RD421 - RD426
1RD431 - RD435
1RD441 - RD442
1RD451 - RD456
1RD461
1RD471 - RD475
1RD513 - RD519
1RD531 - RD533
1RD551
1RD561
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 18, 2020
747-21A2577 RB
6 of 33
REQUIREMENTS BULLETIN 747-21A2577
ALERTALERT

### Page 7

GroupVariable Number
1RD571
1RD581 - RD583
1RD591 - RD593
1RD601 - RD607
1RD621 - RD623
1RD641 - RD649
1RD651 - RD659
1RD661
1RD671
1RD681 - RD682
1RD691 - RD692
1RD701 - RD702
1RD721 - RD722
1RD741 - RD742
1RD751 - RD755
1RD761
1RD771 - RD775
1RD781 - RD783
1RD791 - RD792
1RE001
1RF001 - RF002
2RF003 - RF006
1RG001 - RG009
1RG091
1RG095
1RG101 - RG104
1RG121 - RG126
1RG141 - RG142
1RG161 - RG164
1RG171 - RG174
1RG191 - RG193
1RG211 - RG213
1RG221 - RG222
GroupVariable Number
1RH101 - RH102
1RH111 - RH112
1RH121 - RH122
1RJ131 - RJ133
1RJ151 - RJ152
1RJ301 - RJ303
1RJ321 - RJ322
1RJ331 - RJ333
1RL401 - RL403
1RL411 - RL420
2RL421 - RL436
2RL451 - RL456
2RL461 - RL462
2RL471 - RL481
2RL491 - RL492
2RL501 - RL502
2RL511 - RL516
2RL521 - RL522
2RL531 - RL534
2RL551
2RL561 - RL568
2RL571 - RL572
2RL576 - RL577
2RL579
2RL581 - RL586
1RL651 - RL655
1RL671
2RL672 - RL675
2RL681 - RL684
1RL751 - RL752
1RM001 - RM007
1RM010 - RM013
1RM021 - RM024
GroupVariable Number
1RM026 - RM029
2RM030
1RM036 - RM045
1RM051 - RM052
2RM053
1RM071
1RM081 - RM084
1RM091
1RM096 - RM097
1RM116 - RM117
1RM126 - RM132
1RM136 - RM147
1RM156 - RM158
1RM166 - RM177
1RM191 - RM192
1RM231 - RM233
1RM241 - RM246
1RM261 - RM264
1RM316 - RM318
1RM331 - RM333
1RM341
1RM351 - RM355
1RM366 - RM367
2RM401 - RM403
2RM426
2RM431
2RM441 - RM443
2RM445
1RM801 - RM803
1RM811 - RM813
1RM851 - RM858
2RM859
1RM861 - RM862
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 18, 2020
747-21A2577 RB
7 of 33
REQUIREMENTS BULLETIN 747-21A2577
ALERTALERT

### Page 8

GroupVariable Number
2RM863
1RM871 - RM877
2RM878 - RM880
1RM881 - RM887
2RM888 - RM890
1RM891 - RM899
1RM901 - RM905
2RM906
1RM911
1RR001 - RR005
1RR021 - RR025
1RR031
1RR201 - RR206
1RR221 - RR226
1RR261 - RR267
1RR301 - RR310
1RR331 - RR332
1RR336
1RR341 - RR345
1RR361 - RR362
1RR421 - RR422
1RR431 - RR432
1RR441 - RR442
1RR451
1RR501 - RR504
1RR521 - RR522
1RR526
1RR531
1RR551 - RR556
1RR561
1RR566
1RR701
1RR721 - RR724
GroupVariable Number
1RR746 - RR748
1RR851 - RR856
1RR861 - RR862
1RR951 - RR952
1RS001 - RS002
1RS201
1RS211 - RS212
1RS221 - RS222
1RS231 - RS241
1RS251 - RS259
1RS263
1RS265 - RS268
1RS271 - RS276
1RS291 - RS292
1RS301 - RS306
1RS311 - RS320
1RS331 - RS333
1RS341 - RS342
1RS699
1RS701 - RS703
1RS711 - RS713
1RS721 - RS722
1RS731 - RS732
1RS741 - RS743
1RS751 - RS752
1RS761 - RS762
1RS771
1RS781 - RS782
1RS786
1RT001 - RT014
1RT021 - RT022
1RT031 - RT035
1RT041 - RT047
GroupVariable Number
1RT061
1RT071 - RT075
1RT101 - RT103
1RT121
1RT131 - RT137
1RT151 - RT152
1RT161 - RT168
1RT401 - RT412
1RT431 - RT447
1RT451 - RT469
1RT471 - RT499
1RT501 - RT535
1RT551 - RT568
1RT571 - RT591
1RT601 - RT657
1RT671 - RT673
1RT681 - RT682
1RT691 - RT699
1RT701 - RT704
1RT711 - RT717
1RT741 - RT757
1RT776 - RT777
1RT781 - RT784
1RT801 - RT803
1RT811 - RT814
1RT831 - RT837
1RT861 - RT864
1RT876 - RT880
1RT931 - RT932
1RT945 - RT949
1RT951 - RT955
1RT966 - RT967
1RU001 - RU006
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 18, 2020
747-21A2577 RB
8 of 33
REQUIREMENTS BULLETIN 747-21A2577
ALERTALERT

### Page 9

GroupVariable Number
1RU016 - RU017
1RU031 - RU032
1RU051 - RU052
GroupVariable Number
1RU059 - RU062
1RU081 - RU083
1RU101 - RU102
GroupVariable Number
1RU121 - RU132
1RU801 - RU809
1RU831 - RU841
B. Spares Affected
None
2. CONCURRENT REQUIREMENTS
None.
3. COMPLIANCE
Federal Aviation Administration (FAA) Airworthiness Directive AD 2007-07-03 is related to this service
bulletin. The effective date of AD 2007-07-03 is May 2, 2007.
The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to
Requirements Bulletin 747-21A2577 RB. The Airworthiness Directive will make the compliance tasks and
times given in Requirements Bulletin 747-21A2577 RB mandatory.
When more than one OPTION is given for a CONDITION, do only one of the OPTION numbers. When
more than one ACTION is given for a CONDITION or an OPTION, do all of the ACTION numbers for that
CONDITION or OPTION.
Accomplish the required actions, based on the applicable conditions below in accordance with
Accomplishment Instructions.
Group 1, Configuration 1:
Table 1: Original Fiberglass Fabric Material TADD Inspection & Replacement
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
-Within 1,200 flight
hours after the origi-
nal issue date of
Requirements Bul-
letin 747-21A2577
RB
Do a Detailed Inspection of the
original fiberglass fabric material
TADD for damage. (a)
All airplanes with any original
fiberglass fabric material TADD
installed
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 18, 2020
747-21A2577 RB
9 of 33
REQUIREMENTS BULLETIN 747-21A2577
ALERTALERT

### Page 10

Group 1, Configuration 1:
Table 1: Original Fiberglass Fabric Material TADD Inspection & Replacement
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
1,200 Flight Hours-CONDITION 1 (ACTION 1): Re-
peat Detailed Inspection of the
original fiberglass fabric material
TADD for damage. (a)
CONDITION 1:
NO TADD DAMAGE FOUND (a)
-Within 3,600 flight
hours after the origi-
nal issue date of
Requirements Bul-
letin 747-21A2577
RB
CONDITION 1 (ACTION 2): Re-
place the original fiberglass fabric
material TADD with new high
temperature composite material
TADD.
-At the times speci-
fied in Table 2
CONDITION 1 (ACTION 3): Do
the actions specified in Table 2.
-Before Further
Flight
Do a Detailed Inspection of the
center wing tank secondary fuel
barrier, adjacent to the original
fiberglass fabric material TADD,
for thermal damage. (b)
CONDITION 2:
ANY TADD DAMAGE FOUND
(a)
-Before Further
Flight
CONDITION 2.1 (ACTION 1):
Replace the damaged original
fiberglass fabric material TADD
with new high temperature com-
posite material TADD.
CONDITION 2.1:
NO CENTER WING TANK SEC-
ONDARY FUEL BARRIER DAM-
AGE FOUND (b)
-At the times speci-
fied in Table 2
CONDITION 2.1 (ACTION 2): Do
the actions specified in Table 2.
-Before Further
Flight
CONDITION 2.2 (ACTION 1): Do
a Detailed Inspection of the cen-
ter wing tank primary sealant,
adjacent to the original fiberglass
fabric material TADD, for thermal
damage. (c)
CONDITION 2.2:
ANY CENTER WING TANK
SECONDARY FUEL BARRIER
DAMAGE FOUND (b)
-Before Further
Flight
CONDITION 2.2 (ACTION 2):
Measure the electrical conductiv-
ity change of the upper skin of
the center wing tank, adjacent to
the TADD, for indication of dam-
age. (d)
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 18, 2020
747-21A2577 RB
10 of 33
REQUIREMENTS BULLETIN 747-21A2577
ALERTALERT

### Page 11

Group 1, Configuration 1:
Table 1: Original Fiberglass Fabric Material TADD Inspection & Replacement
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
-Before Further
Flight
CONDITION 2.2.1 (ACTION 1):
Repair damaged secondary fuel
barrier.
CONDITION 2.2.1:
NO CENTER WING TANK PRI-
MARY SEALANT AND UPPER
SKIN DAMAGE FOUND (c)(d) -Before Further
Flight
CONDITION 2.2.1 (ACTION 2):
Replace the damaged original
fiberglass fabric material TADD
with new high temperature com-
posite material TADD.
-At the times speci-
fied in Table 2
CONDITION 2.2.1 (ACTION 3):
Do the actions specified in Table
2.
-Before Further
Flight
CONDITION 2.2.2 (ACTION 1):
Repair damaged primary sealant
and damaged secondary fuel
barrier.
CONDITION 2.2.2:
ANY CENTER WING TANK PRI-
MARY SEALANT DAMAGE
FOUND (c)
-Before Further
Flight
CONDITION 2.2.2 (ACTION 2):
Replace the damaged original
fiberglass fabric material TADD
with new high temperature com-
posite material TADD. (e)
-At the times speci-
fied in Table 2
CONDITION 2.2.2 (ACTION 3):
Do the actions specified in Table
2.
-Before Further
Flight
CONDITION 2.2.3 (ACTION 1):
Contact The Boeing Company for
repair instructions, and do the
repair.
CONDITION 2.2.3:
ANY CENTER WING TANK UP-
PER SKIN DAMAGE FOUND (d)
-Before Further
Flight
CONDITION 2.2.3 (ACTION 2):
Replace the damaged original
fiberglass fabric material TADD
with new high temperature com-
posite material TADD. (e)
-At the times speci-
fied in Table 2
CONDITION 2.2.3 (ACTION 3):
Do the actions specified in Table
2.
(a) TADD damage is defined as any signs of unsecure connection between the TADD and the diffuser duct,
TADD delamination, removed TADD surface material, softened TADD material, or blackened material on
TADD surface that can be easily rubbed off with hand.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 18, 2020
747-21A2577 RB
11 of 33
REQUIREMENTS BULLETIN 747-21A2577
ALERTALERT

### Page 12

Group 1, Configuration 1:
Table 1: Original Fiberglass Fabric Material TADD Inspection & Replacement
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
(b) Center wing tank secondary fuel barrier thermal damage is defined as:
– Cracks, crazing, opacity, or missing secondary fuel barrier sealant
– Change in the secondary barrier sealant properties, such as hardening, or extensive bubbling
– Circular pattern of darkened secondary barrier sealant below the trim air duct leak
– Changes to the color of the secondary barrier sealant compared to areas not exposed to the hot air
leak
(c) Center wing tank primary sealant thermal damage is defined as:
– Blisters, bubbles, cracks, missing or displaced sealant, hardening or color changes
(d) Center wing tank upper skin damage is indicated by a conductivity change of 1% International Annealed
Copper Standard (IACS) or more from the identified baseline conductivity values.
(e) If both Condition 2.2.2 and Condition 2.2.3 apply, the action of "Replace the original fiberglass fabric ma-
terial TADD with new high temperature composite material TADD" is only required to be done once.
Group 1, Configuration 2:
Table 2: High Temperature Composite Material TADD Inspection / Replacement
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
-Within 16,000 flight
hours after replace-
ment or Within
3,600 flight hours
after the original is-
sue date of Require-
ments Bulletin 747-
21A2577 RB,
whichever occurs
later
Do a Detailed Inspection of the
high temperature composite ma-
terial TADD for damage. (a)
All airplanes that have replaced
any original fiberglass fabric ma-
terial TADD with any high temper-
ature composite material TADD,
and the flight hours since replace-
ment is known
-Within 3,600 flight
hours after the origi-
nal issue date of
Requirements Bul-
letin 747-21A2577
RB
All airplanes that have replaced
any original fiberglass fabric ma-
terial TADD with any high temper-
ature composite material TADD,
and the flight hours since replace-
ment is unknown
1,200 Flight Hours-Repeat Detailed Inspection of the
high temperature composite ma-
terial TADD for damage. (a)
CONDITION 3:
NO TADD DAMAGE FOUND (a)
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 18, 2020
747-21A2577 RB
12 of 33
REQUIREMENTS BULLETIN 747-21A2577
ALERTALERT

### Page 13

Group 1, Configuration 2:
Table 2: High Temperature Composite Material TADD Inspection / Replacement
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
-Before Further
Flight
Do a Detailed Inspection of the
center wing tank secondary fuel
barrier, adjacent to the high tem-
perature composite material
TADD, for thermal damage. (b)
CONDITION 4:
ANY TADD DAMAGE FOUND
(a)
-Before Further
Flight
CONDITION 4.1 (ACTION 1):
Replace the damaged high tem-
perature composite material
TADD with new high temperature
composite material TADD.
CONDITION 4.1:
NO CENTER WING TANK SEC-
ONDARY FUEL BARRIER DAM-
AGE FOUND (b)
-16,000 Flight Hours
After Replacement
CONDITION 4.1 (ACTION 2): Do
a Detailed Inspection of the high
temperature composite material
TADD for damage. (a)
-Before Further
Flight
CONDITION 4.2 (ACTION 1): Do
a Detailed Inspection of the cen-
ter wing tank primary sealant,
adjacent to the high temperature
composite material TADD, for
thermal damage. (c)
CONDITION 4.2:
ANY CENTER WING TANK
SECONDARY FUEL BARRIER
DAMAGE FOUND (b)
-Before Further
Flight
CONDITION 4.2 (ACTION 2):
Measure the electrical conductiv-
ity change of the upper skin of
the center wing tank, adjacent to
the TADD, for indication of dam-
age. (d)
-Before Further
Flight
CONDITION 4.2.1 (ACTION 1):
Repair damaged secondary fuel
barrier.
CONDITION 4.2.1:
NO CENTER WING TANK PRI-
MARY SEALANT AND UPPER
SKIN DAMAGE FOUND (c)(d) -Before Further
Flight
CONDITION 4.2.1 (ACTION 2):
Replace the damaged high tem-
perature composite material
TADD with new high temperature
composite material TADD.
-16,000 Flight Hours
After Replacement
CONDITION 4.2.1 (ACTION 3):
Do a Detailed Inspection of the
high temperature composite ma-
terial TADD for damage. (a)
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 18, 2020
747-21A2577 RB
13 of 33
REQUIREMENTS BULLETIN 747-21A2577
ALERTALERT

### Page 14

Group 1, Configuration 2:
Table 2: High Temperature Composite Material TADD Inspection / Replacement
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
-Before Further
Flight
CONDITION 4.2.2 (ACTION 1):
Repair damaged primary sealant
and damaged secondary fuel
barrier.
CONDITION 4.2.2:
ANY CENTER WING TANK PRI-
MARY SEALANT DAMAGE
FOUND (c)
-Before Further
Flight
CONDITION 4.2.2 (ACTION 2):
Replace the damaged high tem-
perature composite material
TADD with new high temperature
composite material TADD. (e)
-16,000 Flight Hours
After Replacement
CONDITION 4.2.2 (ACTION 3):
Do a Detailed Inspection of the
high temperature composite ma-
terial TADD for damage. (a)
-Before Further
Flight
CONDITION 4.2.3 (ACTION 1):
Contact The Boeing Company for
repair instructions, and do the
repair.
CONDITION 4.2.3:
ANY CENTER WING TANK UP-
PER SKIN DAMAGE FOUND (d)
-Before Further
Flight
CONDITION 4.2.3 (ACTION 2):
Replace the damaged high tem-
perature composite material
TADD with new high temperature
composite material TADD. (e)
-16,000 Flight Hours
After Replacement
CONDITION 4.2.3 (ACTION 3):
Do a Detailed Inspection of the
high temperature composite ma-
terial TADD for damage. (a)
(a) TADD damage is defined as any signs of unsecure connection between the TADD and the diffuser duct,
TADD delamination, removed TADD surface material, softened TADD material, or blackened material on
TADD surface that can be easily rubbed off with hand.
(b) Center wing tank secondary fuel barrier thermal damage is defined as:
– Cracks, crazing, opacity, or missing secondary fuel barrier sealant
– Change in the secondary barrier sealant properties, such as hardening, or extensive bubbling
– Circular pattern of darkened secondary barrier sealant below the trim air duct leak
– Changes to the color of the secondary barrier sealant compared to areas not exposed to the hot air
leak
(c) Center wing tank primary sealant thermal damage is defined as:
– Blisters, bubbles, cracks, missing or displaced sealant, hardening or color changes
(d) Center wing tank upper skin damage is indicated by a conductivity change of 1% International Annealed
Copper Standard (IACS) or more from the identified baseline conductivity values.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 18, 2020
747-21A2577 RB
14 of 33
REQUIREMENTS BULLETIN 747-21A2577
ALERTALERT

### Page 15

Group 1, Configuration 2:
Table 2: High Temperature Composite Material TADD Inspection / Replacement
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
(e) If both Condition 4.2.2 and Condition 4.2.3 apply, the action of "Replace the damaged high temperature
composite material TADD with new high temperature composite material TADD" is only required to be
done once.
Group 2:
Table 3: High Temperature Composite Material TADD Inspection / Replacement
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
-Before 16,000 total
flight hours or Within
3,600 flight hours
after the original is-
sue date of Require-
ments Bulletin 747-
21A2577 RB,
whichever occurs
later
Do a Detailed Inspection of the
high temperature composite ma-
terial TADD for damage. (a)
All airplanes with any high temper-
ature composite material TADD
that has not been replaced
-Within 16,000 flight
hours after replace-
ment or Within
3,600 flight hours
after the original is-
sue date of Require-
ments Bulletin 747-
21A2577 RB,
whichever occurs
later
All airplanes with any high temper-
ature composite material TADD
that has been replaced, and the
flight hours since replacement is
known
-Within 3,600 flight
hours after the origi-
nal issue date of
Requirements Bul-
letin 747-21A2577
RB
All airplanes with any high temper-
ature composite material TADD
that has been replaced, and the
flight hours since replacement is
unknown
1,200 Flight Hours-Repeat Detailed Inspection of the
high temperature composite ma-
terial TADD for damage. (a)
CONDITION 5:
NO TADD DAMAGE FOUND (a)
-Before Further
Flight
Do a Detailed Inspection of the
center wing tank secondary fuel
barrier, adjacent to the high tem-
perature composite material
TADD, for thermal damage. (b)
CONDITION 6:
ANY TADD DAMAGE FOUND
(a)
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 18, 2020
747-21A2577 RB
15 of 33
REQUIREMENTS BULLETIN 747-21A2577
ALERTALERT

### Page 16

Group 2:
Table 3: High Temperature Composite Material TADD Inspection / Replacement
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
-Before Further
Flight
CONDITION 6.1 (ACTION 1):
Replace the damaged high tem-
perature composite material
TADD with new high temperature
composite material TADD.
CONDITION 6.1:
NO CENTER WING TANK SEC-
ONDARY FUEL BARRIER DAM-
AGE FOUND (b)
-16,000 Flight Hours
After Replacement
CONDITION 6.1 (ACTION 2): Do
a Detailed Inspection of the high
temperature composite material
TADD for damage. (a)
-Before Further
Flight
CONDITION 6.2 (ACTION 1): Do
a Detailed Inspection of the cen-
ter wing tank primary sealant,
adjacent to the high temperature
composite material TADD, for
thermal damage. (c)
CONDITION 6.2:
ANY CENTER WING TANK
SECONDARY FUEL BARRIER
DAMAGE FOUND (b)
-Before Further
Flight
CONDITION 6.2 (ACTION 2):
Measure the electrical conductiv-
ity change of the upper skin of
the center wing tank, adjacent to
the TADD, for indication of dam-
age. (d)
-Before Further
Flight
CONDITION 6.2.1 (ACTION 1):
Repair damaged secondary fuel
barrier.
CONDITION 6.2.1:
NO CENTER WING TANK PRI-
MARY SEALANT AND UPPER
SKIN DAMAGE FOUND (c)(d) -Before Further
Flight
CONDITION 6.2.1 (ACTION 2):
Replace the damaged high tem-
perature composite material
TADD with new high temperature
composite material TADD.
-16,000 Flight Hours
After Replacement
CONDITION 6.2.1 (ACTION 3):
Do a Detailed Inspection of the
high temperature composite ma-
terial TADD for damage. (a)
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 18, 2020
747-21A2577 RB
16 of 33
REQUIREMENTS BULLETIN 747-21A2577
ALERTALERT

### Page 17

Group 2:
Table 3: High Temperature Composite Material TADD Inspection / Replacement
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
-Before Further
Flight
CONDITION 6.2.2 (ACTION 1):
Repair damaged primary sealant
and damaged secondary fuel
barrier.
CONDITION 6.2.2:
ANY CENTER WING TANK PRI-
MARY SEALANT DAMAGE
FOUND (c)
-Before Further
Flight
CONDITION 6.2.2 (ACTION 2):
Replace the damaged high tem-
perature composite material
TADD with new high temperature
composite material TADD. (e)
-16,000 Flight Hours
After Replacement
CONDITION 6.2.2 (ACTION 3):
Do a Detailed Inspection of the
high temperature composite ma-
terial TADD for damage. (a)
-Before Further
Flight
CONDITION 6.2.3 (ACTION 1):
Contact The Boeing Company for
repair instructions, and do the
repair.
CONDITION 6.2.3:
ANY CENTER WING TANK UP-
PER SKIN DAMAGE FOUND (d)
-Before Further
Flight
CONDITION 6.2.3 (ACTION 2):
Replace the damaged high tem-
perature composite material
TADD with new high temperature
composite material TADD. (e)
-16,000 Flight Hours
After Replacement
CONDITION 6.2.3 (ACTION 3):
Do a Detailed Inspection of the
high temperature composite ma-
terial TADD for damage. (a)
(a) TADD damage is defined as any signs of unsecure connection between the TADD and the diffuser duct,
TADD delamination, removed TADD surface material, softened TADD material, or blackened material on
TADD surface that can be easily rubbed off with hand.
(b) Center wing tank secondary fuel barrier thermal damage is defined as:
– Cracks, crazing, opacity, or missing secondary fuel barrier sealant
– Change in the secondary barrier sealant properties, such as hardening, or extensive bubbling
– Circular pattern of darkened secondary barrier sealant below the trim air duct leak
– Changes to the color of the secondary barrier sealant compared to areas not exposed to the hot air
leak
(c) Center wing tank primary sealant thermal damage is defined as:
– Blisters, bubbles, cracks, missing or displaced sealant, hardening or color changes
(d) Center wing tank upper skin damage is indicated by a conductivity change of 1% International Annealed
Copper Standard (IACS) or more from the identified baseline conductivity values.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 18, 2020
747-21A2577 RB
17 of 33
REQUIREMENTS BULLETIN 747-21A2577
ALERTALERT

### Page 18

Group 2:
Table 3: High Temperature Composite Material TADD Inspection / Replacement
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
(e) If both Condition 6.2.2 and Condition 6.2.3 apply, the action of "Replace the damaged high temperature
composite material TADD with new high temperature composite material TADD" is only required to be
done once.
4. APPROVAL
This Requirements Bulletin was examined by the Federal Aviation Administration (FAA). The changes
specified in this document comply with the applicable regulations and are FAA approved, as well as European
Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved
airplanes listed in the service bulletin effectivity. This document and its approval were based on the airplane
in its original Boeing delivery configuration or as modified by other Boeing changes.
If an airplane has a non-Boeing modification or repair that affects a component or system also affected by
this Requirements Bulletin, the operator is responsible for obtaining appropriate regulatory agency approval
before incorporating this Requirements Bulletin.
Group 1
In addition, the Manager of the FAA Seattle ACO Branch approves accomplishment of the inspections
defined in this requirements bulletin as an alternative method of compliance to the requirement of paragraph
(f), (g), (h), (i), and (j) of AD 2007-07-03. All provisions of AD 2007-07-03 that are not specifically referenced
in the above statement remain fully applicable and must be complied with accordingly.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 18, 2020
747-21A2577 RB
18 of 33
REQUIREMENTS BULLETIN 747-21A2577
ALERTALERT

### Page 19

5.    ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL INFORMATION
NOTE: 1. This is an Enhanced Required for Compliance document. There will be a separate
Service Bulletin (SB) and a separate Requirements Bulletin (RB). If an RB is mandated
by an Airworthiness Directive (AD), then all applicable requirements specified in the
RB must be done. For the related SB, some locations are marked RC Start and RC
End to identify the requirements that are restated from the RB. For the related SB,
the areas between RC Start and RC End, including sub-steps and any figures
identified between RC Start and RC End, must be done to comply with the AD.
Therefore, an Alternative Method of Compliance (AMOC) is required for any deviations
to steps between RC Start and RC End, including substeps and identified figures.
For the related SB, the steps not between RC Start and RC End may be deviated
from using accepted methods in accordance with the operator's maintenance or
inspection program without obtaining approval of an AMOC; this is provided that the
steps between RC Start and RC End, including sub-steps and identified figures, can
still be done as specified, and the airplane can be put back in an airworthy condition.
Figures not required for compliance are omitted from the RB.
2. This is an Enhanced Required for Compliance document. The Boeing processes
used to create the Service Bulletin (SB) and the Requirements Bulletin (RB) ensure
that the information between "RC Start" and "RC End" in the SB are identical to the
information in the same sections (Compliance, Work Instructions...) of the RB which
the SB refers to as the related document.
3. These work instructions refer to procedures included in other Boeing documents.
When the words "refer to" are used and the operator has an accepted alternative
procedure, the accepted alternative procedure can be used. When the words "in
accordance with" are included in the instruction, the procedure in the Boeing document
must be used.
4. The compliance times for the actions in WORK INSTRUCTIONS are in Compliance.
5. When more than one OPTION is given for a CONDITION, do only one of the OPTION
numbers. When more than one ACTION is given for a CONDITION or an OPTION,
do all of the ACTION numbers for that CONDITION or OPTION.
6. The CONDITIONS and ACTIONS shown apply to each affected part independently.
7. If it is necessary to remove more parts for access, you can remove those parts. If
you can get access without removing identified parts, it is not necessary to remove
all of the identified parts. Jacking and shoring limitations must be observed.
8. Original Fiberglass Fabric Material TADD is defined as the list of TADDs, indicated
by part numbers, in APPENDIX A. High Temperature Composite Material TADD is
defined as the list of TADDs, indicated by part numbers, in APPENDIX B.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 18, 2020
747-21A2577 RB
19 of 33
REQUIREMENTS BULLETIN 747-21A2577
ALERTALERT

### Page 20

9. Detailed Inspection (DET) is defined as an intensive examination of a specific item,
installation or assembly to detect damage, failure or irregularity. This could include
tactile assessment in which a component or assembly can be checked for tightness
or security. Available lighting is normally supplemented with a direct source of good
lighting at an intensity deemed appropriate. Inspection aids such as mirrors and
magnifying lenses may be necessary. Surface cleaning and elaborate access
procedures may be required.
B. WORK INSTRUCTIONS
Actions Required for Compliance
1. Requirements:
Group 1, Configuration 1:
Table 1: Original Fiberglass Fabric Material TADD Inspection & Replacement
Refer to the listed
procedures in SB
747-21A2577 Origi-
nal Issue or later
approved issues
as an accepted
procedure
Method of Compli-
ance
ActionCondition
PART 1: Open Ac-
cess
-Do a Detailed Inspection of the
original fiberglass fabric material
TADD for damage. (a)
All airplanes with any original
fiberglass fabric material TADD
installed PART 2: Detailed
Inspection of TADD
PART 1: Open Ac-
cess
-CONDITION 1 (ACTION 1): Re-
peat Detailed Inspection of the
original fiberglass fabric material
TADD for damage. (a)
CONDITION 1:
NO TADD DAMAGE FOUND (a)
PART 2: Detailed
Inspection of TADD
PART 3: Replace-
ment of TADD
-CONDITION 1 (ACTION 2): Re-
place the original fiberglass fabric
material TADD with new high
temperature composite material
TADD.
--CONDITION 1 (ACTION 3): Do
the actions specified in Table 2.
PART 4: Detailed
Inspection of Center
Wing Tank Sec-
ondary Fuel Barrier
-Do a Detailed Inspection of the
center wing tank secondary fuel
barrier, adjacent to the original
fiberglass fabric material TADD,
for thermal damage. (b)
CONDITION 2:
ANY TADD DAMAGE FOUND
(a)
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 18, 2020
747-21A2577 RB
20 of 33
REQUIREMENTS BULLETIN 747-21A2577
ALERTALERT

### Page 21

Group 1, Configuration 1:
Table 1: Original Fiberglass Fabric Material TADD Inspection & Replacement
Refer to the listed
procedures in SB
747-21A2577 Origi-
nal Issue or later
approved issues
as an accepted
procedure
Method of Compli-
ance
ActionCondition
PART 3: Replace-
ment of TADD
-CONDITION 2.1 (ACTION 1):
Replace the damaged original
fiberglass fabric material TADD
with new high temperature com-
posite material TADD.
CONDITION 2.1:
NO CENTER WING TANK SEC-
ONDARY FUEL BARRIER DAM-
AGE FOUND (b)
--CONDITION 2.1 (ACTION 2): Do
the actions specified in Table 2.
PART 5: Detailed
Inspection of Center
Wing Tank Primary
Sealant
-CONDITION 2.2 (ACTION 1): Do
a Detailed Inspection of the cen-
ter wing tank primary sealant,
adjacent to the original fiberglass
fabric material TADD, for thermal
damage. (c)
CONDITION 2.2:
ANY CENTER WING TANK
SECONDARY FUEL BARRIER
DAMAGE FOUND (b)
-In accordance with
747 NDT Manual
Part 6, 51-00-00,
Procedure 3
CONDITION 2.2 (ACTION 2):
Measure the electrical conductiv-
ity change of the upper skin of
the center wing tank, adjacent to
the TADD, for indication of dam-
age. (d)
PART 7: Repair of
Center Wing Tank
Secondary Fuel
Barrier
-CONDITION 2.2.1 (ACTION 1):
Repair damaged secondary fuel
barrier.
CONDITION 2.2.1:
NO CENTER WING TANK PRI-
MARY SEALANT AND UPPER
SKIN DAMAGE FOUND (c)(d)
PART 3: Replace-
ment of TADD
-CONDITION 2.2.1 (ACTION 2):
Replace the damaged original
fiberglass fabric material TADD
with new high temperature com-
posite material TADD.
--CONDITION 2.2.1 (ACTION 3):
Do the actions specified in Table
2.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 18, 2020
747-21A2577 RB
21 of 33
REQUIREMENTS BULLETIN 747-21A2577
ALERTALERT

### Page 22

Group 1, Configuration 1:
Table 1: Original Fiberglass Fabric Material TADD Inspection & Replacement
Refer to the listed
procedures in SB
747-21A2577 Origi-
nal Issue or later
approved issues
as an accepted
procedure
Method of Compli-
ance
ActionCondition
PART 8: Repair of
Center Wing Tank
Primary Sealant and
Secondary Fuel
Barrier
-CONDITION 2.2.2 (ACTION 1):
Repair damaged primary sealant
and damaged secondary fuel
barrier.
CONDITION 2.2.2:
ANY CENTER WING TANK PRI-
MARY SEALANT DAMAGE
FOUND (c)
PART 3: Replace-
ment of TADD
-CONDITION 2.2.2 (ACTION 2):
Replace the damaged original
fiberglass fabric material TADD
with new high temperature com-
posite material TADD. (e)
--CONDITION 2.2.2 (ACTION 3):
Do the actions specified in Table
2.
--CONDITION 2.2.3 (ACTION 1):
Contact The Boeing Company for
repair instructions, and do the
repair.
CONDITION 2.2.3:
ANY CENTER WING TANK UP-
PER SKIN DAMAGE FOUND (d)
PART 3: Replace-
ment of TADD
-CONDITION 2.2.3 (ACTION 2):
Replace the damaged original
fiberglass fabric material TADD
with new high temperature com-
posite material TADD. (e)
--CONDITION 2.2.3 (ACTION 3):
Do the actions specified in Table
2.
PART 9: Close Ac-
cess
-
(a) TADD damage is defined as any signs of unsecure connection between the TADD and the diffuser duct,
TADD delamination, removed TADD surface material, softened TADD material, or blackened material on
TADD surface that can be easily rubbed off with hand.
(b) Center wing tank secondary fuel barrier thermal damage is defined as:
– Cracks, crazing, opacity, or missing secondary fuel barrier sealant
– Change in the secondary barrier sealant properties, such as hardening, or extensive bubbling
– Circular pattern of darkened secondary barrier sealant below the trim air duct leak
– Changes to the color of the secondary barrier sealant compared to areas not exposed to the hot air
leak
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 18, 2020
747-21A2577 RB
22 of 33
REQUIREMENTS BULLETIN 747-21A2577
ALERTALERT

### Page 23

Group 1, Configuration 1:
Table 1: Original Fiberglass Fabric Material TADD Inspection & Replacement
Refer to the listed
procedures in SB
747-21A2577 Origi-
nal Issue or later
approved issues
as an accepted
procedure
Method of Compli-
ance
ActionCondition
(c) Center wing tank primary sealant thermal damage is defined as:
– Blisters, bubbles, cracks, missing or displaced sealant, hardening or color changes
(d) Center wing tank upper skin damage is indicated by a conductivity change of 1% International Annealed
Copper Standard (IACS) or more from the identified baseline conductivity values.
(e) If both Condition 2.2.2 and Condition 2.2.3 apply, the action of "Replace the original fiberglass fabric ma-
terial TADD with new high temperature composite material TADD" is only required to be done once.
Group 1, Configuration 2:
Table 2: High Temperature Composite Material TADD Inspection / Replacement
Refer to the listed
procedures in SB
747-21A2577 Origi-
nal Issue or later
approved issues
as an accepted
procedure
Method of Compli-
ance
ActionCondition
PART 1: Open Ac-
cess
-Do a Detailed Inspection of the
high temperature composite ma-
terial TADD for damage. (a)
All airplanes that have replaced
any original fiberglass fabric ma-
terial TADD with any high temper-
ature composite material TADD,
and the flight hours since replace-
ment is known
PART 2: Detailed
Inspection of TADD
PART 1: Open Ac-
cess
-All airplanes that have replaced
any original fiberglass fabric ma-
terial TADD with any high temper-
ature composite material TADD,
and the flight hours since replace-
ment is unknown
PART 2: Detailed
Inspection of TADD
PART 1: Open Ac-
cess
-Repeat Detailed Inspection of the
high temperature composite ma-
terial TADD for damage. (a)
CONDITION 3:
NO TADD DAMAGE FOUND (a)
PART 2: Detailed
Inspection of TADD
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 18, 2020
747-21A2577 RB
23 of 33
REQUIREMENTS BULLETIN 747-21A2577
ALERTALERT

### Page 24

Group 1, Configuration 2:
Table 2: High Temperature Composite Material TADD Inspection / Replacement
Refer to the listed
procedures in SB
747-21A2577 Origi-
nal Issue or later
approved issues
as an accepted
procedure
Method of Compli-
ance
ActionCondition
PART 4: Detailed
Inspection of Center
Wing Tank Sec-
ondary Fuel Barrier
-Do a Detailed Inspection of the
center wing tank secondary fuel
barrier, adjacent to the high tem-
perature composite material
TADD, for thermal damage. (b)
CONDITION 4:
ANY TADD DAMAGE FOUND
(a)
PART 3: Replace-
ment of TADD
-CONDITION 4.1 (ACTION 1):
Replace the damaged high tem-
perature composite material
TADD with new high temperature
composite material TADD.
CONDITION 4.1:
NO CENTER WING TANK SEC-
ONDARY FUEL BARRIER DAM-
AGE FOUND (b)
PART 1: Open Ac-
cess
-CONDITION 4.1 (ACTION 2): Do
a Detailed Inspection of the high
temperature composite material
TADD for damage. (a) PART 2: DetailedInspection of TADD
PART 5: Detailed
Inspection of Center
Wing Tank Primary
Sealant
-CONDITION 4.2 (ACTION 1): Do
a Detailed Inspection of the cen-
ter wing tank primary sealant,
adjacent to the high temperature
composite material TADD, for
thermal damage. (c)
CONDITION 4.2:
ANY CENTER WING TANK
SECONDARY FUEL BARRIER
DAMAGE FOUND (b)
-In accordance with
747 NDT Manual
Part 6, 51-00-00,
Procedure 3
CONDITION 4.2 (ACTION 2):
Measure the electrical conductiv-
ity change of the upper skin of
the center wing tank, adjacent to
the TADD, for indication of dam-
age. (d)
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 18, 2020
747-21A2577 RB
24 of 33
REQUIREMENTS BULLETIN 747-21A2577
ALERTALERT

### Page 25

Group 1, Configuration 2:
Table 2: High Temperature Composite Material TADD Inspection / Replacement
Refer to the listed
procedures in SB
747-21A2577 Origi-
nal Issue or later
approved issues
as an accepted
procedure
Method of Compli-
ance
ActionCondition
PART 7: Repair of
Center Wing Tank
Secondary Fuel
Barrier
-CONDITION 4.2.1 (ACTION 1):
Repair damaged secondary fuel
barrier.
CONDITION 4.2.1:
NO CENTER WING TANK PRI-
MARY SEALANT AND UPPER
SKIN DAMAGE FOUND (c)(d)
PART 3: Replace-
ment of TADD
-CONDITION 4.2.1 (ACTION 2):
Replace the damaged high tem-
perature composite material
TADD with new high temperature
composite material TADD.
PART 1: Open Ac-
cess
-CONDITION 4.2.1 (ACTION 3):
Do a Detailed Inspection of the
high temperature composite ma-
terial TADD for damage. (a) PART 2: DetailedInspection of TADD
PART 8: Repair of
Center Wing Tank
Primary Sealant and
Secondary Fuel
Barrier
-CONDITION 4.2.2 (ACTION 1):
Repair damaged primary sealant
and damaged secondary fuel
barrier.
CONDITION 4.2.2:
ANY CENTER WING TANK PRI-
MARY SEALANT DAMAGE
FOUND (c)
PART 3: Replace-
ment of TADD
-CONDITION 4.2.2 (ACTION 2):
Replace the damaged high tem-
perature composite material
TADD with new high temperature
composite material TADD. (e)
PART 1: Open Ac-
cess
-CONDITION 4.2.2 (ACTION 3):
Do a Detailed Inspection of the
high temperature composite ma-
terial TADD for damage. (a) PART 2: DetailedInspection of TADD
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 18, 2020
747-21A2577 RB
25 of 33
REQUIREMENTS BULLETIN 747-21A2577
ALERTALERT

### Page 26

Group 1, Configuration 2:
Table 2: High Temperature Composite Material TADD Inspection / Replacement
Refer to the listed
procedures in SB
747-21A2577 Origi-
nal Issue or later
approved issues
as an accepted
procedure
Method of Compli-
ance
ActionCondition
--CONDITION 4.2.3 (ACTION 1):
Contact The Boeing Company for
repair instructions, and do the
repair.
CONDITION 4.2.3:
ANY CENTER WING TANK UP-
PER SKIN DAMAGE FOUND (d)
PART 3: Replace-
ment of TADD
-CONDITION 4.2.3 (ACTION 2):
Replace the damaged high tem-
perature composite material
TADD with new high temperature
composite material TADD. (e)
PART 1: Open Ac-
cess
-CONDITION 4.2.3 (ACTION 3):
Do a Detailed Inspection of the
high temperature composite ma-
terial TADD for damage. (a) PART 2: DetailedInspection of TADD
PART 9: Close Ac-
cess
-
(a) TADD damage is defined as any signs of unsecure connection between the TADD and the diffuser duct,
TADD delamination, removed TADD surface material, softened TADD material, or blackened material on
TADD surface that can be easily rubbed off with hand.
(b) Center wing tank secondary fuel barrier thermal damage is defined as:
– Cracks, crazing, opacity, or missing secondary fuel barrier sealant
– Change in the secondary barrier sealant properties, such as hardening, or extensive bubbling
– Circular pattern of darkened secondary barrier sealant below the trim air duct leak
– Changes to the color of the secondary barrier sealant compared to areas not exposed to the hot air
leak
(c) Center wing tank primary sealant thermal damage is defined as:
– Blisters, bubbles, cracks, missing or displaced sealant, hardening or color changes
(d) Center wing tank upper skin damage is indicated by a conductivity change of 1% International Annealed
Copper Standard (IACS) or more from the identified baseline conductivity values.
(e) If both Condition 4.2.2 and Condition 4.2.3 apply, the action of "Replace the damaged high temperature
composite material TADD with new high temperature composite material TADD" is only required to be
done once.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 18, 2020
747-21A2577 RB
26 of 33
REQUIREMENTS BULLETIN 747-21A2577
ALERTALERT

### Page 27

Group 2:
Table 3: High Temperature Composite Material TADD Inspection / Replacement
Refer to the listed
procedures in SB
747-21A2577 Origi-
nal Issue or later
approved issues
as an accepted
procedure
Method of Compli-
ance
ActionCondition
PART 1: Open Ac-
cess
-Do a Detailed Inspection of the
high temperature composite ma-
terial TADD for damage. (a)
All airplanes with any high temper-
ature composite material TADD
that has not been replaced PART 2: Detailed
Inspection of TADD
PART 1: Open Ac-
cess
-All airplanes with any high temper-
ature composite material TADD
that has been replaced, and the
flight hours since replacement is
known
PART 2: Detailed
Inspection of TADD
PART 1: Open Ac-
cess
-All airplanes with any high temper-
ature composite material TADD
that has been replaced, and the
flight hours since replacement is
unknown
PART 2: Detailed
Inspection of TADD
PART 1: Open Ac-
cess
-Repeat Detailed Inspection of the
high temperature composite ma-
terial TADD for damage. (a)
CONDITION 5:
NO TADD DAMAGE FOUND (a)
PART 2: Detailed
Inspection of TADD
PART 4: Detailed
Inspection of Center
Wing Tank Sec-
ondary Fuel Barrier
-Do a Detailed Inspection of the
center wing tank secondary fuel
barrier, adjacent to the high tem-
perature composite material
TADD, for thermal damage. (b)
CONDITION 6:
ANY TADD DAMAGE FOUND
(a)
PART 3: Replace-
ment of TADD
-CONDITION 6.1 (ACTION 1):
Replace the damaged high tem-
perature composite material
TADD with new high temperature
composite material TADD.
CONDITION 6.1:
NO CENTER WING TANK SEC-
ONDARY FUEL BARRIER DAM-
AGE FOUND (b)
PART 1: Open Ac-
cess
-CONDITION 6.1 (ACTION 2): Do
a Detailed Inspection of the high
temperature composite material
TADD for damage. (a) PART 2: DetailedInspection of TADD
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 18, 2020
747-21A2577 RB
27 of 33
REQUIREMENTS BULLETIN 747-21A2577
ALERTALERT

### Page 28

Group 2:
Table 3: High Temperature Composite Material TADD Inspection / Replacement
Refer to the listed
procedures in SB
747-21A2577 Origi-
nal Issue or later
approved issues
as an accepted
procedure
Method of Compli-
ance
ActionCondition
PART 5: Detailed
Inspection of Center
Wing Tank Primary
Sealant
-CONDITION 6.2 (ACTION 1): Do
a Detailed Inspection of the cen-
ter wing tank primary sealant,
adjacent to the high temperature
composite material TADD, for
thermal damage. (c)
CONDITION 6.2:
ANY CENTER WING TANK
SECONDARY FUEL BARRIER
DAMAGE FOUND (b)
-In accordance with
747 NDT Manual
Part 6, 51-00-00,
Procedure 3
CONDITION 6.2 (ACTION 2):
Measure the electrical conductiv-
ity change of the upper skin of
the center wing tank, adjacent to
the TADD, for indication of dam-
age. (d)
PART 7: Repair of
Center Wing Tank
Secondary Fuel
Barrier
-CONDITION 6.2.1 (ACTION 1):
Repair damaged secondary fuel
barrier.
CONDITION 6.2.1:
NO CENTER WING TANK PRI-
MARY SEALANT AND UPPER
SKIN DAMAGE FOUND (c)(d)
PART 3: Replace-
ment of TADD
-CONDITION 6.2.1 (ACTION 2):
Replace the damaged high tem-
perature composite material
TADD with new high temperature
composite material TADD.
PART 1: Open Ac-
cess
-CONDITION 6.2.1 (ACTION 3):
Do a Detailed Inspection of the
high temperature composite ma-
terial TADD for damage. (a) PART 2: DetailedInspection of TADD
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 18, 2020
747-21A2577 RB
28 of 33
REQUIREMENTS BULLETIN 747-21A2577
ALERTALERT

### Page 29

Group 2:
Table 3: High Temperature Composite Material TADD Inspection / Replacement
Refer to the listed
procedures in SB
747-21A2577 Origi-
nal Issue or later
approved issues
as an accepted
procedure
Method of Compli-
ance
ActionCondition
PART 8: Repair of
Center Wing Tank
Primary Sealant and
Secondary Fuel
Barrier
-CONDITION 6.2.2 (ACTION 1):
Repair damaged primary sealant
and damaged secondary fuel
barrier.
CONDITION 6.2.2:
ANY CENTER WING TANK PRI-
MARY SEALANT DAMAGE
FOUND (c)
PART 3: Replace-
ment of TADD
-CONDITION 6.2.2 (ACTION 2):
Replace the damaged high tem-
perature composite material
TADD with new high temperature
composite material TADD. (e)
PART 1: Open Ac-
cess
-CONDITION 6.2.2 (ACTION 3):
Do a Detailed Inspection of the
high temperature composite ma-
terial TADD for damage. (a) PART 2: DetailedInspection of TADD
--CONDITION 6.2.3 (ACTION 1):
Contact The Boeing Company for
repair instructions, and do the
repair.
CONDITION 6.2.3:
ANY CENTER WING TANK UP-
PER SKIN DAMAGE FOUND (d)
PART 3: Replace-
ment of TADD
-CONDITION 6.2.3 (ACTION 2):
Replace the damaged high tem-
perature composite material
TADD with new high temperature
composite material TADD. (e)
PART 1: Open Ac-
cess
-CONDITION 6.2.3 (ACTION 3):
Do a Detailed Inspection of the
high temperature composite ma-
terial TADD for damage. (a) PART 2: DetailedInspection of TADD
PART 9: Close Ac-
cess
-
(a) TADD damage is defined as any signs of unsecure connection between the TADD and the diffuser duct,
TADD delamination, removed TADD surface material, softened TADD material, or blackened material on
TADD surface that can be easily rubbed off with hand.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 18, 2020
747-21A2577 RB
29 of 33
REQUIREMENTS BULLETIN 747-21A2577
ALERTALERT

### Page 30

Group 2:
Table 3: High Temperature Composite Material TADD Inspection / Replacement
Refer to the listed
procedures in SB
747-21A2577 Origi-
nal Issue or later
approved issues
as an accepted
procedure
Method of Compli-
ance
ActionCondition
(b) Center wing tank secondary fuel barrier thermal damage is defined as:
– Cracks, crazing, opacity, or missing secondary fuel barrier sealant
– Change in the secondary barrier sealant properties, such as hardening, or extensive bubbling
– Circular pattern of darkened secondary barrier sealant below the trim air duct leak
– Changes to the color of the secondary barrier sealant compared to areas not exposed to the hot air
leak
(c) Center wing tank primary sealant thermal damage is defined as:
– Blisters, bubbles, cracks, missing or displaced sealant, hardening or color changes
(d) Center wing tank upper skin damage is indicated by a conductivity change of 1% International Annealed
Copper Standard (IACS) or more from the identified baseline conductivity values.
(e) If both Condition 6.2.2 and Condition 6.2.3 apply, the action of "Replace the damaged high temperature
composite material TADD with new high temperature composite material TADD" is only required to be
done once.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 18, 2020
747-21A2577 RB
30 of 33
REQUIREMENTS BULLETIN 747-21A2577
ALERTALERT

### Page 31

Original Fiberglass Fabric Material TADD Assembly Part Numbers
65B41757-7
65B41757-9
65B41757-11
65B41757-13
65B41757-15
65B41757-17
65B41757-19
65B41757-23
65B41757-24
65B41757-28
65B41908-1
65B41908-5
65B41908-9
65B41908-10
65B41908-13
65B41908-14
65B41908-17
65B41908-18
65B41908-19
65B41908-20
65B41908-24
65B41908-26
65B41908-27
65B41908-28
65B41908-31
65B41908-32
65B48059-1
65B48059-4
65B48059-6
65B48059-8
65B48059-9
APPENDIX A:  ORIGINAL FIBERGLASS FABRIC MATERIAL TADD ASSEMBLY PART NUMBERS
(SHEET 1 OF 2)
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 18, 2020
747-21A2577 RB
31 of 33
REQUIREMENTS BULLETIN 747-21A2577
ALERTALERT

### Page 32

Original Fiberglass Fabric Material TADD Assembly Part Numbers
65B48059-11
65B48059-12
214U2119-10
214U2119-11
214U2119-12
214U2119-13
214U2119-14
214U2119-19
APPENDIX A:  ORIGINAL FIBERGLASS FABRIC MATERIAL TADD ASSEMBLY PART NUMBERS
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 18, 2020
747-21A2577 RB
32 of 33
REQUIREMENTS BULLETIN 747-21A2577
ALERTALERT

### Page 33

NotesHigh Temperature Composite Material TADD Assembly Part Numbers
65B41757-29
65B41757-32
65B41757-35
65B41757-37
65B41908-33
65B41908-35
65B41908-39
65B41908-41
65B41908-43
65B41908-44
65B48059-14
65B48059-16
65B48059-17
(a)214U2119-28
(a)214U2119-29
(a)214U2119-30
(a)214U2119-31
(a)214U2119-32
214U2119-58
214U2119-59
214U2119-60
214U2119-61
214U2119-62
(a) High temperature composite material TADD assembly part numbers 214U2119-28, 214U2119-29,
214U2119-30, 214U2119-31, and 214U2119-32 cannot be used for new work or new installation into ex-
isting aircraft due to new flammability requirements since September 2, 2005. They are superseded by
part numbers 214U2119-58, 214U2119-59, 214U2119-60, 214U2119-61, and 214U2119-62, respectively.
APPENDIX B:  HIGH TEMPERATURE COMPOSITE MATERIAL TADD ASSEMBLY PART NUMBERS
(SHEET 1 OF 1)
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 18, 2020
747-21A2577 RB
33 of 33
REQUIREMENTS BULLETIN 747-21A2577
ALERTALERT

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
