# Boeing Requirements Bulletin 747-25-3725 RB: No revision named

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2021-0258; AD 2021-14-10 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Requirements Bulletin 747-25-3725 RB](https://openairdocs.org/service-documents/boeing/747-25-3725-rb.md)
- Title as filed: 747-25-3725 RB
- Pages: 11
- PDF: https://openairdocs.org/files/sha256/48/26/482644ecfc3e8ff130c853840d23ae3d8429cbb8989a310b83b2db084f638145
- Page: https://openairdocs.org/service-documents/boeing/747-25-3725-rb/file/482644ecfc3e

## Text

Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Commercial 
Airplanes
747
Requirements Bulletin
SPECIAL ATTENTION
Number: 747-25-3725 RB
Original Issue: October 27, 2020
ATA System: 2500 2552 5317
SUBJECT: EQUIPMENT/FURNISHINGS - Cargo Compartment Insulation Foam - Forward Cargo
Compartment Exposed BMS 8-39 Urethane Foam Inspection and Seal Integrity
Inspection, and On-Condition Replacement
Export of this technology is controlled under the United States Export Administration Regulations (EAR) (15
CFR 300-774). An export license may be required before it is used for development, production or use by foreign
persons from specific countries. The controller of this data has the individual responsibility to abide by all export
laws.
9E991ECCN:
BOEING PROPRIETARY, CONFIDENTIAL AND/OR TRADE SECRET
Copyright © 2020 Boeing.
Unpublished Work. All Rights Reserved.
Treatment of this document and its content is governed by contract with Boeing. Rights to use this document
are licensed on a per aircraft basis and such rights may not be transferable. For more information, contact The
Boeing Company.
Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner,
BBJ, DC-8, DC-9, DC-10, KC-10, KC-46, KDC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8, Poseidon and
Boeing liveries are all trademarks owned by The Boeing Company; and no trademark license is granted in
connection with this document unless provided in writing by Boeing.
Original Issue: October 27, 2020
747-25-3725 RB
1 of 11
3.0

### Page 2

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 27, 2020
747-25-3725 RB
2 of 11
REQUIREMENTS BULLETIN 747-25-3725
BLANK PAGE

### Page 3

Table of Contents
1. EFFECTIVITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
A. Airplanes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
B. Spares Affected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2. CONCURRENT REQUIREMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3. COMPLIANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
4. APPROVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
5. ACCOMPLISHMENT INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
A. General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
B. Work Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 27, 2020
747-25-3725 RB
3 of 11
REQUIREMENTS BULLETIN 747-25-3725

### Page 4

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 27, 2020
747-25-3725 RB
4 of 11
REQUIREMENTS BULLETIN 747-25-3725
BLANK PAGE

### Page 5

Commercial 
Airplanes
747
Requirements Bulletin
SPECIAL ATTENTION
Number: 747-25-3725 RB
Original Issue: October 27, 2020
ATA System: 2500 2552 5317
SUBJECT: EQUIPMENT/FURNISHINGS - Cargo Compartment Insulation Foam - Forward Cargo
Compartment Exposed BMS 8-39 Urethane Foam Inspection and Seal Integrity
Inspection, and On-Condition Replacement
BOEING RECOMMENDS THAT EACH OPERATOR EXAMINE THIS DOCUMENT IMMEDIATELY. THIS IS
AN ENHANCED REQUIRED FOR COMPLIANCE DOCUMENT. THE BOEING PROCESSES USED TO CREATE
THE SERVICE BULLETIN (SB) AND THE REQUIREMENTS BULLETIN (RB) ENSURE THAT THE
INFORMATION BETWEEN "RC START" AND "RC END" IN THE SB ARE IDENTICAL TO THE INFORMATION
IN THE SAME SECTIONS (COMPLIANCE, WORK INSTRUCTIONS…) OF THE RB WHICH THE SB REFERS
TO AS THE RELATED DOCUMENT.
1. Effectivity
A. Airplanes
This bulletin is applicable to 747-400, 747-400D, 747-400F Airplane(s), line number(s) 696, 700,
705, 708, 715, 717, 721-723, 725-749, 751, 753-771, 773-775, 777-809, 811-813, 815-817,
819-821, 823-877, 879-885, 887-1374 in 1 Group(s). Where the effectivity is presented with hyphens
between line numbers, the airplane applicability means "through" and "inclusive", e.g. line numbers
1-9 means line numbers 1 through 9 inclusive.
The Variable Numbers and Group Information for the applicable airplanes is given below.
DESCRIPTIONCONFIGURATIONGROUP
747-400, 747-400D, 747-400F Airplanes that were delivered with
BMS 8-39 urethane foam installed in the penetrations through the
insulation blankets between Body Station (STA) 960 and STA 1000
in the forward cargo compartment, left and right side.
-1
Airplane Models:
747-400, 747-400D, 747-400F
GroupVariable Number
1RF001 - RF006
1RL401 - RL403
GroupVariable Number
1RL411 - RL429
1RL431 - RL436
GroupVariable Number
1RL451 - RL455
1RL461 - RL462
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 27, 2020
747-25-3725 RB
5 of 11

### Page 6

GroupVariable Number
1RL471 - RL472
1RL491 - RL492
1RL501 - RL502
1RL651 - RL655
1RL671 - RL675
1RL681 - RL683
1RL751 - RL752
1RM001 - RM007
1RM010 - RM013
1RM021 - RM024
1RM026 - RM030
1RM036 - RM045
1RM051 - RM053
1RM071
1RM081 - RM084
1RM091
1RM096 - RM097
1RM116 - RM117
1RM126 - RM132
1RM136 - RM147
1RM156 - RM158
1RM166 - RM177
1RM191 - RM192
1RM231 - RM233
1RM241 - RM246
1RM261 - RM264
1RM316 - RM318
1RM331 - RM333
1RM341
1RM351 - RM355
1RM366 - RM367
1RM401 - RM403
GroupVariable Number
1RM426
1RM431
1RM441 - RM443
1RM445
1RM801 - RM803
1RM811 - RM813
1RM851 - RM859
1RM861 - RM863
1RM871 - RM889
1RM891 - RM899
1RM901 - RM906
1RM911
1RR701
1RR721 - RR724
1RR746 - RR748
1RR851 - RR856
1RR861 - RR862
1RR951 - RR952
1RT001 - RT014
1RT021 - RT022
1RT031 - RT035
1RT041 - RT047
1RT061
1RT071 - RT075
1RT101 - RT103
1RT121
1RT131 - RT137
1RT151 - RT152
1RT161 - RT168
1RT401 - RT412
1RT431 - RT447
1RT451 - RT469
GroupVariable Number
1RT471 - RT499
1RT501 - RT535
1RT551 - RT568
1RT571 - RT591
1RT601 - RT657
1RT671 - RT673
1RT681 - RT682
1RT691 - RT699
1RT701 - RT704
1RT711 - RT717
1RT741 - RT757
1RT776 - RT777
1RT781 - RT784
1RT801 - RT803
1RT811 - RT814
1RT831 - RT837
1RT861 - RT864
1RT876 - RT880
1RT931 - RT932
1RT945 - RT949
1RT951 - RT955
1RT966 - RT967
1RU001 - RU006
1RU016 - RU017
1RU031 - RU032
1RU051 - RU052
1RU059 - RU062
1RU081 - RU083
1RU101 - RU102
1RU121 - RU132
1RU801 - RU809
1RU831 - RU841
B. Spares Affected
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 27, 2020
747-25-3725 RB
6 of 11
REQUIREMENTS BULLETIN 747-25-3725

### Page 7

None.
2. CONCURRENT REQUIREMENTS
None.
3. COMPLIANCE
The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to
Requirements Bulletin 747-25-3725 RB. The Airworthiness Directive will make the compliance tasks and
times given in Requirements Bulletin 747-25-3725 RB mandatory.
Accomplish the required action(s), based on the applicable condition(s) in Table 1, in accordance with the
Accomplishment Instructions.
Table 1: Exposed BMS 8-39 Urethane Foam Inspection and Seal Integrity Inspection, and On-
Condition Replacement
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
-Within 72 months
after the Original
Issue date of Re-
quirements Bulletin
747-25-3725 RB.
In the forward cargo
compartment, between
STA 960 and STA 1000
on the left and right sides,
do a general visual in-
spection of all penetra-
tions through the insula-
tion blankets for exposed
BMS 8-39 urethane foam
and for seal integrity.
All Airplanes
-Before further
flight.
Replace the seal. Use
BMS 1-68 silicone foam
to fill all the open spaces.
Use insulation blanket
tape to ensure the seal
provides a smoke barrier
without air space be-
tween blankets, tape,
foam, system runs and/or
wires.
CONDITION 1: ANY PEN-
ETRATION WHERE EX-
POSED BMS 8-39 URE-
THANE FOAM IS FOUND.
-Before further
flight.
Replace the seal. Use
BMS 1-68 silicone foam
to fill all the open spaces.
Use insulation blanket
tape to ensure the seal
provides a smoke barrier
without air space be-
tween blankets, tape,
foam, system runs and/or
wires.
CONDITION 2: ANY PEN-
ETRATION WHERE EX-
POSED BMS 8-39 URE-
THANE FOAM IS NOT
FOUND AND SEAL IN-
TEGRITY IS NOT AC-
CEPTABLE.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 27, 2020
747-25-3725 RB
7 of 11
REQUIREMENTS BULLETIN 747-25-3725

### Page 8

Table 1: Exposed BMS 8-39 Urethane Foam Inspection and Seal Integrity Inspection, and On-
Condition Replacement
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
--No further action required
at that location only.
CONDITION 3: ANY PEN-
ETRATION WHERE EX-
POSED BMS 8-39 URE-
THANE FOAM IS NOT
FOUND AND SEAL IN-
TEGRITY IS ACCEPT-
ABLE.
4. APPROVAL
NOTE: The approval statement that follows is valid for all affected airplanes, except 747-400D airplanes.
This Requirements Bulletin was examined by the Federal Aviation Administration (FAA). The changes
specified in this document comply with the applicable regulations and are FAA approved, as well as European
Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved
airplanes listed in the service bulletin effectivity. This document and its approval were based on the airplane
in its original Boeing delivery configuration or as modified by other Boeing changes.
If an airplane has a non-Boeing modification or repair that affects a component or system also affected by
this Requirements Bulletin, the operator is responsible for obtaining appropriate regulatory agency approval
before incorporating this Requirements Bulletin.
NOTE: The approval statement that follows is valid for 747-400D airplanes.
This Requirements Bulletin was examined by the Federal Aviation Administration (FAA). The changes
specified in this service bulletin comply with the applicable regulations and are FAA approved for the
airplanes listed in the service bulletin effectivity. This document and its approval were based on the airplane
in its original Boeing delivery configuration or as modified by other approved Boeing changes.
If an airplane has a non-Boeing modification or repair that affects a component or system also affected by
this Requirements Bulletin, the operator is responsible for obtaining appropriate regulatory agency approval
before incorporating this Requirements Bulletin.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 27, 2020
747-25-3725 RB
8 of 11
REQUIREMENTS BULLETIN 747-25-3725

### Page 9

5.    ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL INFORMATION
NOTE: 1. This is an Enhanced Required for Compliance document. There will be a separate
Service Bulletin (SB) and a separate Requirements Bulletin (RB). If an RB is mandated
by an Airworthiness Directive (AD), then all applicable requirements specified in the
RB must be done. For the related SB, some locations are marked RC Start and RC
End to identify the requirements that are restated from the RB. For the related SB,
the areas between RC Start and RC End, including sub-steps and any figures
identified between RC Start and RC End, must be done to comply with the AD.
Therefore, an Alternative Method of Compliance (AMOC) is required for any deviations
to steps between RC Start and RC End, including substeps and identified figures.
For the related SB, the steps not between RC Start and RC End may be deviated
from using accepted methods in accordance with the operator's maintenance or
inspection program without obtaining approval of an AMOC; this is provided that the
steps between RC Start and RC End, including sub-steps and identified figures, can
still be done as specified, and the airplane can be put back in an airworthy condition.
Figures not required for compliance are omitted from the RB.
2. This is an Enhanced Required for Compliance document. The Boeing processes
used to create the Service Bulletin (SB) and the Requirements Bulletin (RB) ensure
that the information between "RC Start" and "RC End" in the SB are identical to the
information in the same sections (Compliance, Work Instructions...) of the RB which
the SB refers to as the related document.
3. The compliance times for the actions in WORK INSTRUCTIONS are in Compliance.
4. Unless shown differently, these dimensions and tolerances are used:
– Linear dimensions are in inches
– Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus
or minus 0.03 inch
– Tolerance on rivet and bolt edge margin is plus or minus 0.05 inch
– Angular tolerance is plus or minus 2 degrees
– Hole dimensions for standard solid rivets and fasteners are in Structural Repair
Manual (SRM) Chapter 51
– Torque Values:
— Values for structural fasteners are given in 747-400, -400D, -400F Structural
Repair Manual, Chapter 51.
— Values for airframe maintenance tasks are included in Chapter 20 of 747-400
Aircraft Maintenance Manual (AMM).
5. These work instructions refer to procedures included in other Boeing documents.
When the words "refer to" are used and the operator has an accepted alternative
procedure, the accepted alternative procedure can be used. When the words "in
accordance with" are included in the instruction, the procedure in the Boeing document
must be used.
6. If it is necessary to remove more parts for access, you can remove those parts. If
you can get access without removing identified parts, it is not necessary to remove
all of the identified parts. Jacking and shoring limitations must be observed.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 27, 2020
747-25-3725 RB
9 of 11
REQUIREMENTS BULLETIN 747-25-3725

### Page 10

7. A General Visual Inspection is defined as: A visual examination of an interior or
exterior area, installation or assembly to detect obvious damage, failure or irregularity.
This level of inspection is made from within touching distance, unless otherwise
specified. A mirror may be necessary to enhance visual access to all exposed surfaces
in the inspection area. This level of inspection is made under normally available
lighting conditions such as daylight, hangar lighting, flashlight or drop-light and may
require removal or opening of access panels or doors. Stands, ladders or platforms
may be required to gain proximity to the area being checked. Basic cleaning may be
required to ensure appropriate visibility.
8. Refer to SWPM 20-10-11 and SWPM 20-10-12 for the wire installation procedures,
and SWPM 20-10-19 for the wire separation requirements, as accepted procedures.
9. A seal of acceptable integrity provides a smoke barrier without air space between
blankets, tape, foam, system runs and/or wires. The inspection to know the integrity
of the seals is to be done by a visual check that looks at a penetration externally. If
no air spaces can be seen, that is a seal of acceptable integrity.
B. WORK INSTRUCTIONS
Actions Required for Compliance
1. Requirements
Table 1: Exposed BMS 8-39 Urethane Foam Inspection and Seal Integrity Inspection, and On-Condition
Replacement
Refer to the listed proce-
dures in SB 747-25-3725
Original Issue or later
approved revisions as an
accepted procedure
Method of ComplianceActionCondition
PART 1: OPEN ACCESS-In the forward cargo com-
partment, between STA
960 and STA 1000 on the
left and right sides, do a
general visual inspection
of all penetrations through
the insulation blankets for
exposed BMS 8-39 ure-
thane foam and for seal
integrity.
All Airplanes
PART 2: FORWARD
CARGO COMPARTMENT
- INSPECTION FOR EX-
POSED BMS 8-39 URE-
THANE FOAM AND FOR
SEAL INTEGRITY
PART 3: FORWARD
CARGO COMPARTMENT
- EXPOSED BMS 8-39
URETHANE FOAM RE-
PLACEMENT AND SEAL
REPLACEMENT
-Replace the seal. Use
BMS 1-68 silicone foam to
fill all the open spaces.
Use insulation blanket tape
to ensure the seal provides
a smoke barrier without air
space between blankets,
tape, foam, system runs
and/or wires.
CONDITION 1: ANY PEN-
ETRATION WHERE EX-
POSED BMS 8-39 URE-
THANE FOAM IS FOUND.
PART 4: CLOSE ACCESS
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 27, 2020
747-25-3725 RB
10 of 11
REQUIREMENTS BULLETIN 747-25-3725

### Page 11

Table 1: Exposed BMS 8-39 Urethane Foam Inspection and Seal Integrity Inspection, and On-Condition
Replacement
Refer to the listed proce-
dures in SB 747-25-3725
Original Issue or later
approved revisions as an
accepted procedure
Method of ComplianceActionCondition
PART 3: FORWARD
CARGO COMPARTMENT
- EXPOSED BMS 8-39
URETHANE FOAM RE-
PLACEMENT AND SEAL
REPLACEMENT
-Replace the seal. Use
BMS 1-68 silicone foam to
fill all the open spaces.
Use insulation blanket tape
to ensure the seal provides
a smoke barrier without air
space between blankets,
tape, foam, system runs
and/or wires.
CONDITION 2: ANY PEN-
ETRATION WHERE EX-
POSED BMS 8-39 URE-
THANE FOAM IS NOT
FOUND AND SEAL IN-
TEGRITY IS NOT AC-
CEPTABLE. PART 4: CLOSE ACCESS
PART 4: CLOSE ACCESS-No further action required
at that location only.
CONDITION 3: ANY PEN-
ETRATION WHERE EX-
POSED BMS 8-39 URE-
THANE FOAM IS NOT
FOUND AND SEAL IN-
TEGRITY IS ACCEPT-
ABLE.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 27, 2020
747-25-3725 RB
11 of 11
REQUIREMENTS BULLETIN 747-25-3725

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
