# Boeing Special Attention Requirements Bulletin 747-25-3726 RB: No revision named

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2022-0985; AD 2022-25-04 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Special Attention Requirements Bulletin 747-25-3726 RB](https://openairdocs.org/service-documents/boeing/747-25-3726-rb.md)
- Title as filed: 747-25-3726 RB
- Pages: 36
- PDF: https://openairdocs.org/files/sha256/da/95/da95eb311647624426db009a4d74f9d9534738774c54135346ccc63b2416064d
- Page: https://openairdocs.org/service-documents/boeing/747-25-3726-rb/file/da95eb311647

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Commercial 
Airplanes
747
Requirements Bulletin
SPECIAL ATTENTION
Number: 747-25-3726 RB
Original Issue: January 06, 2022
ATA System: 2562
SUBJECT: EQUIPMENT/FURNISHINGS - Life Raft Compartment Door - Door 5 Ceiling Stowage
Box Snubber Replacement
EXPORT CONTROLLED - This technology or software is subject to the U.S. Export Administration Regulations
(EAR), (15 C.F.R. Parts 730-774). No authorization from the U.S. Department of Commerce is required for
export, re-export, in-country transfer, or access EXCEPT to country group E:1 or E:2 countries/persons per
Supp.1 to Part 740 of the EAR.
9E991ECCN:
Copyright © 2022 Boeing.
Unpublished Work. All Rights Reserved.
Treatment of this document and its content is governed by contract with Boeing. Rights to use this document
are licensed on a per aircraft basis and such rights may not be transferable. For more information, contact The
Boeing Company.
Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner,
BBJ, DC-8, DC-9, DC-10, KC-10, KC-46, KDC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8, Poseidon and
Boeing liveries are all trademarks owned by The Boeing Company; and no trademark license is granted in
connection with this document unless provided in writing by Boeing.
Original Issue: January 06, 2022
747-25-3726 RB
1 of 36
3.0

### Page 2

Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: January 06, 2022
747-25-3726 RB
2 of 36
REQUIREMENTS BULLETIN 747-25-3726
BLANK PAGE

### Page 3

Table of Contents
1. EFFECTIVITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
A. Airplanes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
B. Spares Affected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2. CONCURRENT REQUIREMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3. COMPLIANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
4. APPROVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
5. ACCOMPLISHMENT INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
A. General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
B. Work Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
FIGURE 4: DOOR 5 CEILING STOWAGE BOX DOOR ASSEMBLY (INNER BOX) - SNUBBER
ATTACHMENT LOCATION CHANGE [Group 2, Configuration 2] . . . . . . . . . . . . . . 16
FIGURE 5: DOOR 5 LEFT CEILING STOWAGE BOX ASSEMBLY (OUTER BOX) - SNUBBER
ATTACHMENT LOCATION CHANGE [Group 2, Configuration 2] . . . . . . . . . . . . . . 23
FIGURE 6: DOOR 5 RIGHT CEILING STOWAGE BOX ASSEMBLY (OUTER BOX) - SNUBBER
ATTACHMENT LOCATION CHANGE [Group 2, Configuration 2] . . . . . . . . . . . . . . 30
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: January 06, 2022
747-25-3726 RB
3 of 36
REQUIREMENTS BULLETIN 747-25-3726

### Page 4

Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: January 06, 2022
747-25-3726 RB
4 of 36
REQUIREMENTS BULLETIN 747-25-3726
BLANK PAGE

### Page 5

Commercial 
Airplanes
747
Requirements Bulletin
SPECIAL ATTENTION
Number: 747-25-3726 RB
Original Issue: January 06, 2022
ATA System: 2562
SUBJECT: EQUIPMENT/FURNISHINGS - Life Raft Compartment Door - Door 5 Ceiling Stowage
Box Snubber Replacement
BOEING RECOMMENDS THAT EACH OPERATOR EXAMINE THIS DOCUMENT IMMEDIATELY. THIS IS
AN ENHANCED REQUIRED FOR COMPLIANCE DOCUMENT. THE BOEING PROCESSES USED TO CREATE
THE SERVICE BULLETIN (SB) AND THE REQUIREMENTS BULLETIN (RB) ENSURE THAT THE
INFORMATION BETWEEN "RC START" AND "RC END" IN THE SB ARE IDENTICAL TO THE INFORMATION
IN THE SAME SECTIONS (COMPLIANCE, WORK INSTRUCTIONS…) OF THE RB WHICH THE SB REFERS
TO AS THE RELATED DOCUMENT.
1. Effectivity
A. Airplanes
This bulletin is applicable to 747-8, 747-400 Airplane(s), line number(s) 696, 700, 705, 708, 715,
721-723, 725-734, 736, 740-742, 744, 746, 751, 753, 755-759, 761-762, 764-765, 767-768, 771,
773-774, 779-782, 784, 786-790, 794-804, 806-808, 811, 815-817, 819-821, 823-826, 828-829,
832-833, 835-837, 839, 841-843, 845, 847, 849, 851, 855, 857-860, 863, 865-867, 869-871, 873,
875-877, 881-883, 887-890, 894-895, 897-898, 900-903, 905-906, 908-913, 915-919, 923-924,
926, 928, 930-931, 933, 936-937, 939-940, 942-945, 947, 949-950, 954-959, 964-967, 969-971,
973-974, 976-977, 979, 982-989, 993, 995, 997, 999-1001, 1003, 1007, 1009-1011, 1013, 1015,
1017-1019, 1021-1022, 1024-1025, 1027-1035, 1037-1039, 1041, 1043, 1045, 1047-1048, 1050,
1054-1059, 1061-1063, 1067, 1071-1075, 1078-1085, 1088-1089, 1091-1093, 1095, 1097-1100,
1102-1104, 1106-1111, 1113-1114, 1116-1118, 1120-1122, 1124, 1126, 1129-1130, 1132-1138,
1140-1162, 1164, 1166-1168, 1170-1172, 1174, 1176-1178, 1180, 1182-1183, 1185-1187,
1190-1191, 1193-1202, 1204-1209, 1211-1212, 1214-1216, 1218-1219, 1221, 1223, 1226, 1228,
1230, 1232-1234, 1236-1237, 1239, 1241, 1243, 1245, 1247, 1250, 1253, 1261-1262, 1264-1266,
1268, 1270, 1272-1278, 1280, 1284, 1287, 1289-1290, 1292-1293, 1296-1297, 1299, 1301, 1303,
1308, 1313, 1320-1321, 1324-1325, 1327, 1330-1331, 1335-1337, 1343, 1353-1354, 1357-1358,
1434, 1439-1440, 1443, 1446, 1449, 1451, 1453, 1456, 1459, 1466, 1468, 1470, 1472, 1475,
1477, 1480, 1492, 1494-1495, 1497-1500, 1503, 1506-1515, 1517-1519, 1523-1525, 1527, 1529,
1531, 1537-1539 in 3 Group(s). Where the effectivity is presented with hyphens between line
numbers, the airplane applicability means "through" and "inclusive", e.g. line numbers 1-9 means
line numbers 1 through 9 inclusive.
The Variable Numbers and Group Information for the applicable airplanes is given below. An
equivalent change is on subsequent production airplanes.
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: January 06, 2022
747-25-3726 RB
5 of 36

### Page 6

DESCRIPTIONCONFIGURATIONGROUP
747-400 Airplanes delivered with snubber part number SP5378
installed.
-1
747-8 Airplanes delivered with snubber part number SP5378 installed
that are affected by Boeing service bulletin 747-25-3674.
-2
Airplanes that have done Boeing service bulletin 747-25-3674.1
Airplanes that have not done Boeing service bulletin 747-25-3674.2
747-8 Airplanes delivered with snubber part number SP5378 installed
that are not affected by Boeing service bulletin 747-25-3674 and
have the production equivalent of Boeing service bulletin 747-25-3674.
-3
Airplane Models:
747-400, 747-8
GroupVariable Number
3RC001 - RC005
2RC006 - RC009
3RC022 - RC024
2RC025 - RC038
3RC039 - RC040
3RC051 - RC060
2RC066 - RC069
3RC070 - RC072
3RC076 - RC077
1RF001 - RF006
1RM001 - RM007
1RM010 - RM013
1RM021 - RM024
1RM026 - RM030
1RM036 - RM045
1RM051 - RM053
1RM071
1RM081 - RM084
GroupVariable Number
1RM091
1RM096 - RM097
1RM116 - RM117
1RM126 - RM127
1RM129 - RM132
1RM136 - RM147
1RM156 - RM158
1RM166 - RM177
1RM191 - RM192
1RM231 - RM233
1RM241 - RM246
1RM261 - RM264
1RM316 - RM318
1RM331 - RM333
1RM341
1RM351 - RM355
1RM366 - RM367
1RM401 - RM403
GroupVariable Number
1RM426
1RM431
1RM441 - RM443
1RM445
1RT401 - RT412
1RT431 - RT447
1RT451 - RT454
1RT457 - RT460
1RT462 - RT469
1RT471 - RT499
1RT502 - RT505
1RT511 - RT512
1RT514 - RT515
1RT517
1RT521 - RT523
1RT525
1RT527
1RT529
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: January 06, 2022
747-25-3726 RB
6 of 36
REQUIREMENTS BULLETIN 747-25-3726

### Page 7

GroupVariable Number
1RT531 - RT535
1RT551 - RT568
1RT571
1RT580 - RT591
1RT601 - RT630
1RT633 - RT641
1RT643 - RT653
1RT671 - RT673
1RT681 - RT682
1RT693 - RT699
1RT701 - RT704
1RT711 - RT717
GroupVariable Number
1RT741 - RT742
1RT744 - RT750
1RT753 - RT757
1RT776 - RT777
1RT783 - RT784
1RT801 - RT803
1RT811 - RT814
1RT831 - RT836
1RT861 - RT864
1RT877 - RT880
1RT931 - RT932
1RT945 - RT949
GroupVariable Number
1RT951 - RT955
1RT966
1RU001 - RU006
1RU016 - RU017
1RU031 - RU032
1RU059 - RU062
1RU081 - RU083
1RU101 - RU102
1RU121 - RU132
1RU809
--
--
B. Spares Affected
NotesNew Part NumberNameExisting Part
Number
(a)(b)SP26172RATE CONTROL - SNUBBERSP5378
(a) Discard the existing part.
(b) You cannot use the existing part to replace the new part.
2. CONCURRENT REQUIREMENTS
None.
3. COMPLIANCE
The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to
Requirements Bulletin 747-25-3726 RB. The Airworthiness Directive will make the compliance tasks and
times given in Requirements Bulletin 747-25-3726 RB mandatory.
Accomplish the required action(s), based on the applicable condition(s) in Table(s) 1 through 3, in accordance
with Accomplishment Instructions.
When more than one OPTION is given for a CONDITION, do only one of the OPTION numbers. When
more than one ACTION is given for a CONDITION or an OPTION, do all of the ACTION numbers for that
CONDITION or OPTION.
Where Tables 1 through 3 specify to do an Operation Check 1 and Operation Check 2, Operation Check
1 and Operation Check 2 are defined as follows:
Operation Check 1:
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: January 06, 2022
747-25-3726 RB
7 of 36
REQUIREMENTS BULLETIN 747-25-3726

### Page 8

– Fully open and close each door 5 ceiling stowage box a minimum of three times to properly distribute
the oil inside the snubber. Do an operation check to ensure the free fall distance is no greater than 2.5
inches from the fully closed position at the forward outer edge of the door assembly.
Operation Check 2:
– Do an operation check to ensure the free fall distance is no greater than 2.5 inches from the fully closed
position at the forward outer edge of the door assembly. Each snubber must be independently evaluated
for this operation check. Disengage one snubber while performing operation check for other one.
Group 1; Group 2, Configuration 1; Group 3:
Table 1: Door 5 Ceiling Stowage Box Snubber Replacement
Repeat Interval
(Not to Exceed)
Boeing Recommended
Compliance Time
ActionCondition
-Within 6 months after the
Original Issue date of
Requirements Bulletin
747-25-3726 RB.
ACTION 1: Replace snubber part
number SP5378 with part number
SP26172 on the left and right sides
of each door 5 ceiling stowage box.
All Airplanes
ACTION 2: Do Operation Check 1
of the left and right sides of each
door 5 ceiling stowage box.
-Before further flight.CONDITION 1 (ACTION 1): Do ap-
plicable corrective action and make
sure the free fall distance is no
greater than 2.5 inches.
CONDITION 1: THE FREE
FALL DISTANCE IS
GREATER THAN 2.5
INCHES
At the times specified in
Table 3.
CONDITION 1 (ACTION 2): Do the
Post Snubber Replacement Check
specified in Table 3.
-At the times specified in
Table 3.
Do the Post Snubber Replacement
Check specified in Table 3.
CONDITION 2: THE FREE
FALL DISTANCE IS 2.5
INCHES OR LESS
Group 2, Configuration 2:
Table 2: Change the Location of the Snubber Attachments and Door 5 Ceiling Stowage Box Snubber
Replacement
Repeat Interval
(Not to Exceed)
Boeing Recommended
Compliance Time
ActionCondition
-Within 6 months after the
Original Issue date of
Requirements Bulletin
747-25-3726 RB.
ACTION 1: Change the location of
the snubber attachments, and re-
place snubber part number SP5378
with the part number SP26172 on
the left and right sides of each door
5 ceiling stowage box.
All Airplanes
ACTION 2: Do Operation Check 1
of the left and right sides of each
door 5 ceiling stowage box.
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: January 06, 2022
747-25-3726 RB
8 of 36
REQUIREMENTS BULLETIN 747-25-3726

### Page 9

Group 2, Configuration 2:
Table 2: Change the Location of the Snubber Attachments and Door 5 Ceiling Stowage Box Snubber
Replacement
Repeat Interval
(Not to Exceed)
Boeing Recommended
Compliance Time
ActionCondition
-Before further flight.CONDITION 1 (ACTION 1): Do ap-
plicable corrective action and make
sure the free fall distance is no
greater than 2.5 inches.
CONDITION 1: THE FREE
FALL DISTANCE IS
GREATER THAN 2.5
INCHES
At the times specified in
Table 3.
CONDITION 1 (ACTION 2): Do the
Post Snubber Replacement Check
specified in Table 3.
-At the times specified in
Table 3.
Do the Post Snubber Replacement
Check specified in Table 3.
CONDITION 2: THE FREE
FALL DISTANCE IS 2.5
INCHES OR LESS
Table 3: Post Snubber Replacement Check
Repeat Interval
(Not to Exceed)
Boeing Recommended
Compliance Time
(Whichever Occurs First)
ActionCondition
-Within 3 years
after snubber
replacement.
Within 15,000
flight hours after
snubber replace-
ment.
Do Operation Check 2 of
the snubber on the left
and right sides of each
door 5 ceiling stowage
box.
Airplanes with snubber part
number SP26172.
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: January 06, 2022
747-25-3726 RB
9 of 36
REQUIREMENTS BULLETIN 747-25-3726

### Page 10

Table 3: Post Snubber Replacement Check
Repeat Interval
(Not to Exceed)
Boeing Recommended
Compliance Time
(Whichever Occurs First)
ActionCondition
-Before further flight.CONDITION 1 (ACTION
1): Replace any affected
snubber, part number
SP26172, with a new
snubber, part number
SP26172.
CONDITION 1: THE FREE
FALL DISTANCE IS
GREATER THAN 2.5
INCHES
-Before further flight.CONDITION 1 (ACTION
2): Do Operation Check
1 of each affected door 5
ceiling stowage box. If the
ceiling stowage box free
fall distance is greater
than 2.5 inches, do appli-
cable corrective action
and make sure the free
fall distance is no greater
than 2.5 inches.
15,000 flight hours
or 3 years,
whichever occurs
first.
-CONDITION 1 (ACTION
3): Repeat Operation
Check 2 of the snubber
on the left and right sides
of each door 5 ceiling
stowage box.
15,000 flight hours
or 3 years,
whichever occurs
first.
-Repeat Operation Check
2 of the snubber on the
left and right sides of
each door 5 ceiling
stowage box.
CONDITION 2: THE FREE
FALL DISTANCE IS 2.5
INCHES OR LESS
4. APPROVAL
This Requirements Bulletin was examined by the Federal Aviation Administration (FAA). The changes
specified in this document comply with the applicable regulations and are FAA approved, as well as European
Union Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved
airplanes listed in this Requirements Bulletin effectivity. This document and its approval were based on the
airplane in its original Boeing delivery configuration or as modified by other Boeing changes.
If an airplane has a non-Boeing modification or repair that affects a component or system also affected by
this Requirements Bulletin, the operator is responsible for obtaining appropriate regulatory agency approval
before incorporating this Requirements Bulletin.
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: January 06, 2022
747-25-3726 RB
10 of 36
REQUIREMENTS BULLETIN 747-25-3726

### Page 11

5.    ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL INFORMATION
NOTE: 1. This is an Enhanced Required for Compliance document. There will be a separate
Service Bulletin (SB) and a separate Requirements Bulletin (RB). If an RB is mandated
by an Airworthiness Directive (AD), then all applicable requirements specified in the
RB must be done. For the related SB, some locations are marked RC Start and RC
End to identify the requirements that are restated from the RB. For the related SB,
the areas between RC Start and RC End, including sub-steps and any figures
identified between RC Start and RC End, must be done to comply with the AD.
Therefore, an Alternative Method of Compliance (AMOC) is required for any deviations
to steps between RC Start and RC End, including substeps and identified figures.
For the related SB, the steps not between RC Start and RC End may be deviated
from using accepted methods in accordance with the operator's maintenance or
inspection program without obtaining approval of an AMOC; this is provided that the
steps between RC Start and RC End, including sub-steps and identified figures, can
still be done as specified, and the airplane can be put back in an airworthy condition.
Figures not required for compliance are omitted from the RB.
2. This is an Enhanced Required for Compliance document. The Boeing processes
used to create the Service Bulletin (SB) and the Requirements Bulletin (RB) ensure
that the information between "RC Start" and "RC End" in the SB are identical to the
information in the same sections (Compliance, Work Instructions...) of the RB which
the SB refers to as the related document.
3. The compliance times for the actions in WORK INSTRUCTIONS are in Compliance.
4. Unless shown differently, these dimensions and tolerances are used:
– Linear dimensions are in inches
– Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus
or minus 0.03 inch
– Tolerance on rivet and bolt edge margin is plus or minus 0.05 inch
– Angular tolerance is plus or minus 2 degrees
– Hole dimensions for standard solid rivets and fasteners are in Structural Repair
Manual (SRM) Chapter 51
– Torque Values:
— Values for structural fasteners are given in 747 Structural Repair Manual,
Chapter 51.
— Values for airframe maintenance tasks are included in Chapter 20 of 747
Aircraft Maintenance Manual (AMM).
— Non-standard torque values for maintenance tasks are included in the
applicable installation step.
5. These work instructions refer to procedures included in other Boeing documents.
When the words "refer to" are used and the operator has an accepted alternative
procedure, the accepted alternative procedure can be used. When the words "in
accordance with" are included in the instruction, the procedure in the Boeing document
must be used.
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: January 06, 2022
747-25-3726 RB
11 of 36
REQUIREMENTS BULLETIN 747-25-3726

### Page 12

6. If it is necessary to remove more parts for access, you can remove those parts. If
you can get access without removing identified parts, it is not necessary to remove
all of the identified parts. Jacking and shoring limitations must be observed.
7. Where the work instructions include installation of a kept part, a new or serviceable
part with the same part number can be installed as an alternative to the kept part.
8. Use the approved fastener, process and material substitutions in accordance with
SRM Chapter 51.
9. When more than one OPTION is given for a CONDITION, do only one of the OPTION
numbers. When more than one ACTION is given for a CONDITION or an OPTION,
do all of the ACTION numbers for that CONDITION or OPTION.
10. If the length of any fastener specified in this service bulletin does not meet installation
standards given in SRM Chapter 51, then a fastener of the same specification, or
an approved substitute, with a length which meets the installation standards given
in SRM Chapter 51 may be used. In addition, washers may be installed for fastener
grip length in accordance with SRM Chapter 51. Refer to SOPM 20-50-01 for alternate
full threaded fasteners (screws) needed for installation in this service bulletin.
B. WORK INSTRUCTIONS
Actions Required for Compliance
1. Requirements
Where Tables 1 through 3 specify to do an Operation Check 1 and Operation Check 2, Operation
Check 1 and Operation Check 2 are defined as follows:
Operation Check 1:
– Fully open and close each door 5 ceiling stowage box a minimum of three times to properly
distribute the oil inside the snubber. Do an operation check to ensure the free fall distance is
no greater than 2.5 inches from the fully closed position at the forward outer edge of the door
assembly.
Operation Check 2:
– Do an operation check to ensure the free fall distance is no greater than 2.5 inches from the
fully closed position at the forward outer edge of the door assembly. Each snubber must be
independently evaluated for this operation check. Disengage one snubber while performing
operation check for other one.
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: January 06, 2022
747-25-3726 RB
12 of 36
REQUIREMENTS BULLETIN 747-25-3726

### Page 13

Group 1; Group 2, Configuration 1; Group 3:
Table 1: Door 5 Ceiling Stowage Box Snubber Replacement
Refer to the listed procedures in
SB 747-25-3726 Original Issue or
later approved revisions as an
accepted procedure
Method of
Compliance
ActionCondition
PART 1: DOOR 5 CEILING
STOWAGE BOX - OPEN ACCESS
-ACTION 1: Replace snubber part
number SP5378 with part number
SP26172 on the left and right sides
of each door 5 ceiling stowage box.
All Airplanes
PART 2: DOOR 5 CEILING
STOWAGE BOX SNUBBER RE-
PLACEMENT
PART 5: DOOR 5 CEILING
STOWAGE BOX - OPERATION
CHECK 1
-ACTION 2: Do Operation Check 1
of the left and right sides of each
door 5 ceiling stowage box.
PART 9: DOOR 5 CEILING
STOWAGE BOX - CLOSE ACCESS
-CONDITION 1 (ACTION 1): Do ap-
plicable corrective action and make
sure the free fall distance is no
greater than 2.5 inches.
CONDITION 1:
THE FREE FALL
DISTANCE IS
GREATER THAN
2.5 INCHES --CONDITION 1 (ACTION 2): Do the
Post Snubber Replacement Check
specified in Table 3.
--Do the Post Snubber Replacement
Check specified in Table 3.
CONDITION 2:
THE FREE FALL
DISTANCE IS 2.5
INCHES OR LESS
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: January 06, 2022
747-25-3726 RB
13 of 36
REQUIREMENTS BULLETIN 747-25-3726

### Page 14

Group 2, Configuration 2:
Table 2: Change the Location of the Snubber Attachments and Door 5 Ceiling Stowage Box Snubber
Replacement
Refer to the listed procedures in
SB 747-25-3726 Original Issue or
later approved revisions as an
accepted procedure
Method of
Compliance
ActionCondition
PART 1: DOOR 5 CEILING
STOWAGE BOX - OPEN ACCESS
-ACTION 1: Change the location of
the snubber attachments, and re-
place snubber part number SP5378
with the part number SP26172 on
the left and right sides of each door
5 ceiling stowage box.
All Airplanes
PART 3: DOOR 5 CEILING
STOWAGE BOX REMOVAL AND
SNUBBER REMOVAL
Refer to APPENDIX B - BLIND AND
THROUGH INSERT INSTALLA-
TION as an accepted procedure
-
-FIGURE 4
FIGURE 5
FIGURE 6
PART 4: DOOR 5 CEILING
STOWAGE BOX INSTALLATION
AND SNUBBER INSTALLATION
-
PART 5: DOOR 5 CEILING
STOWAGE BOX - OPERATION
CHECK 1
-ACTION 2: Do Operation Check 1
of the left and right sides of each
door 5 ceiling stowage box.
PART 9: DOOR 5 CEILING
STOWAGE BOX - CLOSE ACCESS
-CONDITION 1 (ACTION 1): Do ap-
plicable corrective action and make
sure the free fall distance is no
greater than 2.5 inches.
CONDITION 1:
THE FREE FALL
DISTANCE IS
GREATER THAN
2.5 INCHES --CONDITION 1 (ACTION 2): Do the
Post Snubber Replacement Check
specified in Table 3.
--Do the Post Snubber Replacement
Check specified in Table 3.
CONDITION 2:
THE FREE FALL
DISTANCE IS 2.5
INCHES OR LESS
Table 3: Post Snubber Replacement Check
Refer to the listed procedures in
SB 747-25-3726 Original Issue or
later approved revisions as an
accepted procedure
Method of
Compliance
ActionCondition
PART 6: DOOR 5 CEILING
STOWAGE BOX - OPERATION
CHECK 2
-Do Operation Check 2 of the snub-
ber on the left and right sides of
each door 5 ceiling stowage box.
Airplanes with
snubber part num-
ber SP26172
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: January 06, 2022
747-25-3726 RB
14 of 36
REQUIREMENTS BULLETIN 747-25-3726

### Page 15

Table 3: Post Snubber Replacement Check
Refer to the listed procedures in
SB 747-25-3726 Original Issue or
later approved revisions as an
accepted procedure
Method of
Compliance
ActionCondition
PART 7: AFFECTED DOOR 5
CEILING STOWAGE BOX - SNUB-
BER REPLACEMENT
-CONDITION 1 (ACTION 1): Replace
any affected snubber, part number
SP26172, with a new snubber, part
number SP26172.
CONDITION 1:
THE FREE FALL
DISTANCE IS
GREATER THAN
2.5 INCHES PART 8: AFFECTED DOOR 5
CEILING STOWAGE BOX - OPER-
ATION CHECK 1
-CONDITION 1 (ACTION 2): Do Op-
eration Check 1 of each affected
door 5 ceiling stowage box. If the
ceiling stowage box free fall distance
is greater than 2.5 inches, do appli-
cable corrective action and make
sure the free fall distance is no
greater than 2.5 inches.
PART 6: DOOR 5 CEILING
STOWAGE BOX - OPERATION
CHECK 2
-CONDITION 1 (ACTION 3): Repeat
Operation Check 2 of the snubber
on the left and right sides of each
door 5 ceiling stowage box.
PART 6: DOOR 5 CEILING
STOWAGE BOX - OPERATION
CHECK 2
-Repeat Operation Check 2 of the
snubber on the left and right sides
of each door 5 ceiling stowage box.
CONDITION 2:
THE FREE FALL
DISTANCE IS 2.5
INCHES OR LESS
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: January 06, 2022
747-25-3726 RB
15 of 36
REQUIREMENTS BULLETIN 747-25-3726

### Page 16 (OCR)

REQUIREMENTS BULLETIN 747-25-3726
This Figure applies only to: Group 2, Configuration 2.
AN
DOOR 5 CEILING STOWAGE BOX DOOR
ASSEMBLY (INNER BOX)
AFT WALL  (BEFORE)
OUTER FACE
FWD
BEFORE  2972561
A-A
FIGURE 4: DOOR 5 CEILING STOWAGE BOX DOOR ASSEMBLY (INNER BOX) - SNUBBER ATTACHMENT
LOCATION CHANGE
(SHEET 1 OF 7)
Original Issue: January 06, 2022
Export Controlled ECCN: 9E991  747-25-3726 RB
Copyright © Unpublished Work - See page 1 for details.  16 of 36

### Page 17 (OCR)

REQUIREMENTS BULLETIN 747-25-3726
SNUBBER
ATTACHMENT
AFT WALL
OUTER FACE
FWD
AFTER  2972562
A-A
FIGURE 4: DOOR 5 CEILING STOWAGE BOX DOOR ASSEMBLY (INNER BOX) - SNUBBER ATTACHMENT
LOCATION CHANGE
(SHEET 2 OF 7)
Original Issue: January 06, 2022
747-25-3726 RB
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.  17 of 36

### Page 18 (OCR)

REQUIREMENTS BULLETIN 747-25-3726
AFTWALL
OUTER FACE
22.40
0.61
3 LOCATIONS (
2972563
FIGURE 4: DOOR 5 CEILING STOWAGE BOX DOOR ASSEMBLY (INNER BOX) - SNUBBER ATTACHMENT
LOCATION CHANGE
(SHEET 3 OF 7)
Original Issue: January 06, 2022
747-25-3726 RB
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.  18 of 36

### Page 19 (OCR)

REQUIREMENTS BULLETIN 747-25-3726
FWD  AFT WALL
OUTER FACE
BEFORE  D
B-B
1 SNUBBER
ATTACHMENT
2972564
FIGURE 4: DOOR 5 CEILING STOWAGE BOX DOOR ASSEMBLY (INNER BOX) - SNUBBER ATTACHMENT
LOCATION CHANGE
(SHEET 4 OF 7)
Original Issue: January 06, 2022
747-25-3726 RB
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.  19 of 36

### Page 20 (OCR)

REQUIREMENTS BULLETIN 747-25-3726
AFT WALL
OUTER FACE
(2)
FWD
AFTER
B-B
AFT WALL
OUTER FACE
• 22.40
0.61
2972566
FIGURE 4: DOOR 5 CEILING STOWAGE BOX DOOR ASSEMBLY (INNER BOX) - SNUBBER ATTACHMENT
LOCATION CHANGE
(SHEET 5 OF 7)
Original Issue: January 06, 2022
Export Controlled ECCN: 9E991  747-25-3726 RB
Copyright © Unpublished Work - See page 1 for details.  20 of 36

### Page 21

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for each door 5 ceiling stowage box assembly (inner
box).
NOTE: This Figure is applicable to ceiling stowage box assemblies (inner boxes) that are for door 5 left and
door 5 right.
More DataQtyIdentificationNameTaskStep
6BACS12FA3K6SCREWRemove / Keep1
2413U5007-1SNUBBER ATTACH-
MENT
Remove / Keep
8412A1811-2BPLUG BUTTON IN-
SERT (BAC 870)
Install (New)2
2413U5007-1SNUBBER ATTACH-
MENT
Put / Hold3
2-HOLEDrill4
FIGURE 4: DOOR 5 CEILING STOWAGE BOX DOOR ASSEMBLY (INNER BOX) - SNUBBER ATTACHMENT
LOCATION CHANGE
(SHEET 6 OF 7)
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: January 06, 2022
747-25-3726 RB
21 of 36
REQUIREMENTS BULLETIN 747-25-3726

### Page 22

More DataQtyIdentificationNameTaskStep
6-HOLEDrill5
6BACI12AG3UCM5INSERT, BLINDInstall (New)6
2SL2334-4A3INSERTInstall (New)7
2413U5007-1SNUBBER ATTACH-
MENT
Install (Kept)8
6BACS12FA3K6SCREWInstall (Kept)
FIGURE 4: DOOR 5 CEILING STOWAGE BOX DOOR ASSEMBLY (INNER BOX) - SNUBBER ATTACHMENT
LOCATION CHANGE
(SHEET 7 OF 7)
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: January 06, 2022
747-25-3726 RB
22 of 36
REQUIREMENTS BULLETIN 747-25-3726

### Page 23 (OCR)

REQUIREMENTS BULLETIN 747-25-3726
This Figure applies only to: Group 2, Configuration 2.
DOOR 5 LEFT CEILING STOWAGE BOX ASSEMBLY
(OUTER BOX)
AFT WALL
OUTER FACE
BEFORE  A-A  2972571
FIGURE 5: DOOR 5 LEFT CEILING STOWAGE BOX ASSEMBLY (OUTER BOX) - SNUBBER ATTACHMENT
LOCATION CHANGE
(SHEET 1 OF 7)
Original Issue: January 06, 2022
747-25-3726 RB
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.  23 of 36

### Page 24 (OCR)

REQUIREMENTS BULLETIN 747-25-3726
AFT WALL
OUTER FACE
FWD
AFTER  2972572
A-A
FIGURE 5: DOOR 5 LEFT CEILING STOWAGE BOX ASSEMBLY (OUTER BOX) - SNUBBER ATTACHMENT
LOCATION CHANGE
(SHEET 2 OF 7)
Original Issue: January 06, 2022
747-25-3726 RB
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.  24 of 36

### Page 25 (OCR)

REQUIREMENTS BULLETIN 747-25-3726
AFT WALL
OUTER FACE
FWD
BEFORE
B-B
AFT WALL
OUTER FACE
00
FWD
AFTER
B-B  2972573
FIGURE 5: DOOR 5 LEFT CEILING STOWAGE BOX ASSEMBLY (OUTER BOX) - SNUBBER ATTACHMENT
LOCATION CHANGE
(SHEET 3 OF 7)
Original Issue: January 06, 2022
Copyright © Unpublished Work - See page 1 for details.  Export Controlled ECCN: 9E991  747-25-3726 RB  25 of 36

### Page 26 (OCR)

REQUIREMENTS BULLETIN 747-25-3726
10.59-
13.80
AFT WALL
INNER FACE
3 LOCATIONS (8
2972574
FIGURE 5: DOOR 5 LEFT CEILING STOWAGE BOX ASSEMBLY (OUTER BOX) - SNUBBER ATTACHMENT
LOCATION CHANGE
(SHEET 4 OF 7)
Original Issue: January 06, 2022
Export Controlled ECCN: 9E991  747-25-3726 RB
Copyright © Unpublished Work - See page 1 for details.  26 of 36

### Page 27 (OCR)

REQUIREMENTS BULLETIN 747-25-3726
10.59•
AFT WALL  13.80
INNER FACE
FWD
2972576
FIGURE 5: DOOR 5 LEFT CEILING STOWAGE BOX ASSEMBLY (OUTER BOX) - SNUBBER ATTACHMENT
LOCATION CHANGE
(SHEET 5 OF 7)
Original Issue: January 06, 2022
Copyright © Unpublished Work - See page 1 for details.  Export Controlled ECCN: 9E991  747-25-3726 RB  27 of 36

### Page 28

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for each door 5 left ceiling stowage box assembly
(outer box).
More DataQtyIdentificationNameTaskStep
6BACS12FA3K7SCREWRemove / Keep1
2413U5007-1SNUBBER ATTACH-
MENT
Remove / Keep
8412A1811-2BPLUG BUTTON IN-
SERT (BAC 870)
Install (New)2
2413U5007-1SNUBBER ATTACH-
MENT
Put / Hold3
6-HOLEDrill4
2-HOLEDrill5
Countersink 100 de-
grees on the outer
surface.
2-HOLECountersink
6BACI12AG3UCM5INSERT, BLINDInstall (New)6
2BACI12AH4U505KINSERTInstall (New)7
FIGURE 5: DOOR 5 LEFT CEILING STOWAGE BOX ASSEMBLY (OUTER BOX) - SNUBBER ATTACHMENT
LOCATION CHANGE
(SHEET 6 OF 7)
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: January 06, 2022
747-25-3726 RB
28 of 36
REQUIREMENTS BULLETIN 747-25-3726

### Page 29

More DataQtyIdentificationNameTaskStep
2413U5007-1SNUBBER ATTACH-
MENT
Install (Kept)8
6BACS12FA3K7SCREWInstall (Kept)
FIGURE 5: DOOR 5 LEFT CEILING STOWAGE BOX ASSEMBLY (OUTER BOX) - SNUBBER ATTACHMENT
LOCATION CHANGE
(SHEET 7 OF 7)
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: January 06, 2022
747-25-3726 RB
29 of 36
REQUIREMENTS BULLETIN 747-25-3726

### Page 30 (OCR)

REQUIREMENTS BULLETIN 747-25-3726
This Figure applies only to: Group 2, Configuration 2.
DOOR 5 RIGHT CEILING STOWAGE BOX ASSEMBLY
(OUTER BOX)
AFT WALL
OUTER FACE
FWD
BEFORE  2972579
A-A
FIGURE 6: DOOR 5 RIGHT CEILING STOWAGE BOX ASSEMBLY (OUTER BOX) - SNUBBER ATTACHMENT
LOCATION CHANGE
(SHEET 1 OF 7)
Original Issue: January 06, 2022
747-25-3726 RB
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.  30 of 36

### Page 31 (OCR)

REQUIREMENTS BULLETIN 747-25-3726
AFT WALL
OUTER FACE
c
FWD
AFTER  A-A  2972580
FIGURE 6: DOOR 5 RIGHT CEILING STOWAGE BOX ASSEMBLY (OUTER BOX) - SNUBBER ATTACHMENT
LOCATION CHANGE
(SHEET 2 OF 7)
Original Issue: January 06, 2022
Export Controlled ECCN: 9E991  747-25-3726 RB
Copyright © Unpublished Work - See page 1 for details.  31 of 36

### Page 32 (OCR)

REQUIREMENTS BULLETIN 747-25-3726
AFT WALL
OUTER FACE
FWD
BEFORE
B-B
AFT WALL
OUTER FACE
AFTER  2972581
B-B
FIGURE 6: DOOR 5 RIGHT CEILING STOWAGE BOX ASSEMBLY (OUTER BOX) - SNUBBER ATTACHMENT
LOCATION CHANGE
(SHEET 3 OF 7)
Original Issue: January 06, 2022
Export Controlled ECCN: 9E991  747-25-3726 RB
Copyright © Unpublished Work - See page 1 for details.  32 of 36

### Page 33 (OCR)

REQUIREMENTS BULLETIN 747-25-3726
10.59 -
13.80
AFT WALL
INNER FACE
FWD
8) 3 LOCATIONS
2972583
FIGURE 6: DOOR 5 RIGHT CEILING STOWAGE BOX ASSEMBLY (OUTER BOX) - SNUBBER ATTACHMENT
LOCATION CHANGE
(SHEET 4 OF 7)
Original Issue: January 06, 2022
747-25-3726 RB
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.  33 of 36

### Page 34 (OCR)

REQUIREMENTS BULLETIN 747-25-3726
10.59
13.80
AFT WALL
INNER FACE
EWD
2972585
FIGURE 6: DOOR 5 RIGHT CEILING STOWAGE BOX ASSEMBLY (OUTER BOX) - SNUBBER ATTACHMENT
LOCATION CHANGE
(SHEET 5 OF 7)
Original Issue: January 06, 2022
Export Controlled ECCN: 9E991  747-25-3726 RB
Copyright © Unpublished Work - See page 1 for details.  34 of 36

### Page 35

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for each door 5 right ceiling stowage box assembly
(outer box).
More DataQtyIdentificationNameTaskStep
6BACS12FA3K7SCREWRemove / Keep1
2413U5007-1SNUBBER ATTACH-
MENT
Remove / Keep
8412A1811-2BPLUG BUTTON IN-
SERT (BAC 870)
Install (New)2
2413U5007-1SNUBBER ATTACH-
MENT
Put / Hold3
6-HOLEDrill4
2-HOLEDrill5
Countersink 100 de-
grees on the outer
surface.
2-HOLECountersink
6BACI12AG3UCM5INSERT, BLINDInstall (New)6
2BACI12AH4U505KINSERTInstall (New)7
FIGURE 6: DOOR 5 RIGHT CEILING STOWAGE BOX ASSEMBLY (OUTER BOX) - SNUBBER ATTACHMENT
LOCATION CHANGE
(SHEET 6 OF 7)
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: January 06, 2022
747-25-3726 RB
35 of 36
REQUIREMENTS BULLETIN 747-25-3726

### Page 36

More DataQtyIdentificationNameTaskStep
2413U5007-1SNUBBER ATTACH-
MENT
Install (Kept)8
6BACS12FA3K7SCREWInstall (Kept)
FIGURE 6: DOOR 5 RIGHT CEILING STOWAGE BOX ASSEMBLY (OUTER BOX) - SNUBBER ATTACHMENT
LOCATION CHANGE
(SHEET 7 OF 7)
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: January 06, 2022
747-25-3726 RB
36 of 36
REQUIREMENTS BULLETIN 747-25-3726

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
