# Boeing Alert Service Bulletin 747-52A2294: U.S. DOT/FAA - Service Information - 1

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2012-0299; AD 2012-25-13 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Alert Service Bulletin 747-52A2294](https://openairdocs.org/service-documents/boeing/747-52a2294.md)
- Title as filed: U.S. DOT/FAA - Service Information - 1
- Pages: 97
- PDF: https://openairdocs.org/files/sha256/98/89/9889346c9c47509c3628aef2aa7fa2f1fad4855f139adc988e16fa6985195845
- Page: https://openairdocs.org/service-documents/boeing/747-52a2294/file/9889346c9c47

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Commercial 
Airplanes
747
Service Bulletin
ALERT
Number: 747-52A2294
Original Issue: July 08, 2010
Revision 1: August 16, 2011
ATA System: 5232
SUBJECT: DOORS - Side Cargo Doors - Main Deck Side Cargo Door Latch Pin and Latch Pin
Retention Bolt Inspection and Modification
Export of this technology is controlled under the United States Export Administration Regulations (EAR) (15
CFR 730-774). An export license may be required before it is used for development, production or use by foreign
persons from specific countries. The controller of this data has the individual responsibility to abide by all export
laws.
9E991ECCN:
BOEING PROPRIETARY, CONFIDENTIAL, AND/OR TRADE SECRET
Copyright © 2010 The Boeing Company
Unpublished Work - All Rights Reserved
Boeing claims copyright in each page of this document only to the extent that the page contains copyrightable
subject matter. Boeing also claims copyright in this document as a compilation and/or collective work.
This document includes proprietary information owned by The Boeing Company and/or one or more third parties.
Treatment of the document and the information it contains is governed by contract with Boeing. For more
information, contact The Boeing Company, P.O. Box 3707, Seattle, Washington 98124.
Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner,
BBJ, DC-8, DC-9, DC-10, KC-10, KDC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8A, Poseidon and the
Boeing livery are all trademarks owned by The Boeing Company; and no trademark license is granted in
connection with this document unless provided in writing by Boeing.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 08, 2010
747-52A2294Revision 1: August 16, 2011
1 of 97
5.0

### Page 2

BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 08, 2010
747-52A2294Revision 1: August 16, 2011
2 of 97
BOEING SERVICE BULLETIN 747-52A2294
ALERTALERT
BLANK PAGE

### Page 3

Table of Contents
Revision Transmittal Sheet ............................................ 5
Summary ...................................................... 9
1. PLANNING INFORMATION ........................................ 1 3
A. Effectivity ............................................... 1 3
1. Airplanes ............................................ 1 3
2. Spares Affected ........................................ 1 9
B. Concurrent Requirements ...................................... 1 9
C. Reason ................................................ 2 0
D. Description .............................................. 2 1
E. Compliance .............................................. 2 2
F. Approval ............................................... 2 8
G. Manpower .............................................. 2 8
H. Weight and Balance Changes .................................... 3 0
I. Electrical Load Data ......................................... 3 0
J. References .............................................. 3 0
1. Existing Data .......................................... 3 0
2. Data supplied with this Service Bulletin ............................ 3 1
3. Installation Drawings Used in the Preparation of this Service Bulletin ............ 3 1
K. Publications Affected ........................................ 3 1
L. Interchangeability and Intermixability of Parts ........................... 3 2
2. MATERIAL INFORMATION ........................................ 3 3
A. Material - Price and Availability ................................... 3 3
B. Industry Support Information .................................... 3 3
C. Parts Necessary For Each Airplane ................................. 3 3
1. Kits/Parts ............................................ 3 3
2. Parts and Materials Supplied by the Operator ........................ 3 5
3. Parts Modified and Reidentified ................................ 3 6
4. Parts Removed and Not Replaced .............................. 3 6
D. Parts Necessary to Change Spares ................................. 3 6
E. Special Tooling - Price and Availability ............................... 3 6
F. Special Tooling Necessary to do this Service Bulletin ....................... 3 7
3. ACCOMPLISHMENT INSTRUCTIONS .................................. 3 9
A. GENERAL INFORMATION ..................................... 3 9
B. WORK INSTRUCTIONS ....................................... 4 0
FIGURE 1: DETAILED INSPECTION ................................... 4 7
FIGURE 2: TORQUE CHECK ....................................... 4 9
FIGURE 3: LATCH PIN POSITION CHECK ................................ 5 1
FIGURE 4: PART REPLACEMENT AT LATCH PIN FITTING POSITIONS #1, #3, #7, #8, #9 AND #10 . 54
FIGURE 5: PART REPLACEMENT AT LATCH PIN FITTING POSITION #2 [Group 1-2, Configuration 2]
.................................................. 5 7
FIGURE 6: PART REPLACEMENT AT LATCH PIN FITTING POSITION #2 [Group 1-2, Configuration 1;
Group 3] ............................................. 6 0
FIGURE 7: PART REPLACEMENT AT LATCH PIN FITTING POSITION #4 .............. 6 3
FIGURE 8: PART REPLACEMENT AT LATCH PIN FITTING POSITION #5 .............. 6 6
FIGURE 9: PART REPLACEMENT AT LATCH PIN FITTING POSITION #6 .............. 6 9
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 08, 2010
747-52A2294Revision 1: August 16, 2011
3 of 97
BOEING SERVICE BULLETIN 747-52A2294
ALERTALERT

### Page 4

FIGURE 10: MODIFICATION AT LATCH PIN FITTING POSITION #1, #3, #7, #8, #9 AND #10 .... 7 2
FIGURE 11: MODIFICATION AT LATCH PIN FITTING POSITION #4 .................. 7 6
FIGURE 12: MODIFICATION AT LATCH PIN FITTING POSITION #5 .................. 8 0
FIGURE 13: MODIFICATION AT LATCH PIN FITTING POSITION #6 .................. 8 4
FIGURE 14: MODIFICATION AT LATCH PIN FITTING POSITION #2 [Group 1-2, Configuration 2] . . 88
FIGURE 15: MODIFICATION AT LATCH PIN FITTING POSITION #2 [Group 1-2, Configuration 1; Group 3]
.................................................. 9 2
FIGURE 16: LATCH PIN REWORK ..................................... 9 6
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 08, 2010
747-52A2294Revision 1: August 16, 2011
4 of 97
BOEING SERVICE BULLETIN 747-52A2294
ALERTALERT

### Page 5

Commercial 
Airplanes
747
Service Bulletin
ALERT
Revision Transmittal SheetNumber: 747-52A2294Original Issue: July 08, 2010
Revision 1: August 16, 2011
ATA System: 5232
SUBJECT: DOORS - Side Cargo Doors - Main Deck Side Cargo Door Latch Pin and Latch Pin
Retention Bolt Inspection and Modification
This revision includes all pages of the service bulletin.
COMPLIANCE INFORMATION RELATED TO THIS REVISION
More work is necessary on the airplane(s) inspected in accordance with the original issue of this service bulletin.
Repeat the latch pin retention bolt inspections at the time given in this service bulletin. In addition, at the time
given in this service bulletin, Boeing recommends that the 3/16 inch diameter latch pin retention bolts be replaced
with 5/16 inch diameter pin retention hardware in accordance with Revision 1.
No airplanes were added to the service bulletin effectivity.
REASON FOR REVISION
This revision is sent to change the one-time inspection given in the original issue of this service bulletin into
repeat inspections. Also, instructions for replacement of the 3/16 inch diameter latch pin retention bolts with
5/16 inch diameter pin retention hardware has been added. This replacement includes modification of the latch
pin fittings and installation of new latch pins. New Figures 10 through 15 have been added.
In addition, this revision identifies another possible configuration for Group 1 and Group 2 airplanes. If the
modification given in Boeing Service Bulletin 747-52-2224 was installed, the configuration of the latch pin
installation at pin fitting position #4 will be different, and similar to position #4 on Group 3 airplanes.
The data given in Information Notice 747-52A2294 IN 01 is included in this revision. IN 01 was sent to clarify
that in Figures 4, 5, 7, 8 and 9 it is acceptable to install an additional washer under the nut if necessary for
fastener grip length adjustment.
These sections have changed:
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 08, 2010
747-52A2294Revision 1: August 16, 2011
5 of 97

### Page 6

1. On the Summary page, the "Action" section was changed to show that the detailed inspections should be
repeated, and to include the retention bolt modification.
2. The illustration on the Summary page was changed to include the retention bolt modification.
3. The Group/Configuration table in Paragraph 1.A.1., Airplanes, was changed to include Configurations 1
and 2 for Groups 1 and 2. These configurations are dependent whether the modification given in Boeing
Service Bulletin 747-52-2224, "Doors - Cargo Doors - Door Warning - Forward and Aft Lower Lobe and
Main Deck Side Cargo Door Warning System Revision" has been installed. The modification changes the
latch pin and retention bolt configuration at latch pin fitting #2.
4. Paragraph 1.B., Concurrent Requirements was changed to include Boeing Service Bulletin 747-52-2258.
5. Paragraph 1.D., Description was changed to show that the detailed inspections should be repeated, and
to include the retention bolt modification.
6. In Paragraph 1.E., Compliance, Table 1 was changed to include repeat inspections, and to include the
retention bolt modification as an alternative to inspection. Table 2 was added to give Compliance information
for the retention bolt modification. Table 3 was added to include the repeated inspections necessary after
the retention bolt modification has been accomplished.
7. In Paragraph 1.G., Manpower, a title was added to the original man-hour table. Tables 2 and 3 were added
for the retention bolt modification and the after-modification inspections.
8. Items were added to Paragraph 1.J.1., Existing Data.
9. Tool Drawing MIT140U8005 was added to Paragraph 1.J.2., Data supplied with this Service Bulletin.
10. In Paragraph 1.K.2., Damage Tolerance Based Structural Inspections:, the paragraph was changed to
indicate that DTIs are included in Paragraph 1.E., Compliance.
11. Paragraph 2.A., Material - Price and Availability and Paragraph 2.C., Parts Necessary for Each Airplane
were changed to include Modification Top Kit 015U1916-1.
12. Paragraph 2.C.3., Parts Modified and Reidentified, was changed to include latch pins that can be reworked.
13. Paragraph 2.E., Special Tooling - Price and Availability and Paragraph 2.F., Special Tooling Necessary to
do this Service Bulletin were changed to include the MIT140U8005-1 tool kit necessary for the retention
bolt modification.
14. In Paragraph 3.A., General Information, additional general notes have been included.
15. In Paragraph 3.B., Work Instructions, PART 4 was changed to describe the proper figure for latch pin fitting
position #2 for the different Configurations of Group 1 and Group 2. PART 5 was changed to specify repeat
inspections. PART 6, describing the retention bolt modification was added. PART 7, describing the
after-modification inspections, was added.
16. Figures 10 - 15 have been added to show details of the latch pin retention bolt modification. Figure 16 was
added to show an optional rework for certain latch pin part numbers.
Vertical lines are put on the left edge of each page, except in Paragraph 1.A., Effectivity, to show the location
of important changes.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 08, 2010
747-52A2294Revision 1: August 16, 2011
6 of 97
BOEING SERVICE BULLETIN 747-52A2294
ALERTALERT

### Page 7

Pages with no vertical lines have no important changes.
REVISION HISTORY
July 08, 2010Original Issue:
August 16, 2011Revision 1:
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 08, 2010
747-52A2294Revision 1: August 16, 2011
7 of 97
BOEING SERVICE BULLETIN 747-52A2294
ALERTALERT

### Page 8

BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 08, 2010
747-52A2294Revision 1: August 16, 2011
8 of 97
BOEING SERVICE BULLETIN 747-52A2294
ALERTALERT
BLANK PAGE

### Page 9

Commercial 
Airplanes
747
Service Bulletin
ALERT
SummaryNumber: 747-52A2294Original Issue: July 08, 2010
Revision 1: August 16, 2011
ATA System: 5232
SUBJECT: DOORS - Side Cargo Doors - Main Deck Side Cargo Door Latch Pin and Latch Pin
Retention Bolt Inspection and Modification
THIS BULLETIN IS SENT TO THE OPERATORS OF RECORD OF THE AIRPLANES SHOWN IN PARAGRAPH
1.A., EFFECTIVITY. IF AN AIRPLANE HAS BEEN LEASED OR SOLD, SEND THIS SERVICE BULLETIN TO
THE NEW OPERATOR. IF APPLICABLE SPARES HAVE BEEN SOLD, SEND THIS SERVICE BULLETIN TO
THE NEW OWNER.
CONCURRENT REQUIREMENTS
Refer to Paragraph 1.B., Concurrent Requirements.
BACKGROUND
Accomplishment of the inspections in this service bulletin will ensure that the latch pin retention bolts in the Main
Deck Side Cargo Door lower sill latch pin fittings are not loose, broken or missing. A loose, broken or missing
retention bolt can result in a migrated latch pin, which can become disengaged from the cargo door latch cams,
and lead to increased loads in the adjacent latch pin fittings and latch cams. Increased loads can cause damage
to the cargo door latch mechanism and/or the lower sill structure. The migration of two or more latch pins and
subsequent failure of the latch mechanism or lower sill structure can result in the inability of the cargo door to
carry limit loads, which could lead to the loss of the cargo door and depressurization of the airplane.
The Main Deck Side Cargo Door has a series of ten latch pin fittings which are attached to the lower sill of the
door cutout and numbered 1 through 10 forward to aft. Latch pins are installed in each latch pin fitting, and each
is secured with a retention bolt. The latch pins and latch pin fittings carry structural and pressurization loads
during flight.
Six operators have reported that broken latch pin retention bolts were found on eight airplanes. On one airplane,
with 101,609 flight-hours and 12,862 flight-cycles, the retention bolts on both the #9 and #10 latch pin fittings
were found to be broken. Latch pin #10 was found to have migrated aft and was not engaging the latch cam.
On another airplane, with 33,983 flight-hours and 4,723 flight-cycles, the retention bolt on the #10 latch pin fitting
was found to be broken and the #9 latch pin was found to be damaged. On another airplane with 67,188
flight-hours and 14,440 flight-cycles, the retention bolt for the #10 latch pin fitting was found to be completely
sheared, which allowed the latch pin to migrate aft until it no longer engaged the door latch cam. On four airplanes,
only the retention bolt on the #10 latch pin fitting was found to be broken. On one airplane the retention bolt on
the #10 latch pin fitting was found to be damaged.
Boeing Service Related Problem (SRP) 747-SRP-52-0093 is related to this service bulletin.
Boeing Fleet Team Digest article 747-FTD-52-09002 is related to this service bulletin.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 08, 2010
747-52A2294Revision 1: August 16, 2011
9 of 97

### Page 10

ACTION (PRR 85901-112RS)
Get access to the lower sill of the Main Deck Side Cargo Door (MDSCD) cutout. Do a Detailed Inspection of all
ten latch pin fittings for loose, broken or missing retention bolts and nuts. Measure the latch pins to make sure
they are within allowable limits.
At any latch pin fitting that does not have a loose, broken or missing retention bolt and nut, and the latch pin is
not damaged beyond the limits given in this service bulletin, remove sealant and do a torque check in accordance
with this service bulletin. If the retention bolt passes the torque check, replace the retention bolt sealant. If the
retention bolt fails the torque check, consider the bolt to be broken.
At any latch pin location where the retention bolt and nut was not found to be broken, loose, damaged or missing,
but the latch pin is damaged beyond the limits given in this service bulletin, replace the latch pin, the retention
bolt, and related parts in accordance with this service bulletin.
At any latch pin fitting with a loose, broken or missing retention bolt or nut, do a check for latch pin migration in
accordance with this service bulletin. If the latch pin has not migrated, replace parts at the affected latch pin
fitting location in accordance with this service bulletin. If the latch pin has migrated, do additional Detailed
Inspections of adjacent door and door cutout structure and latch cams within 42 inches of the affected fitting for
damage in accordance with this service bulletin. Repair any damage that is found. Replace parts at the affected
latch pin fitting location and any adjacent latch pin fitting location in accordance with this service bulletin.
The inspection is complete when the retention bolts at all ten latch pin fitting locations have either passed the
torque check or been replaced in accordance with this service bulletin or other Boeing instructions, and all ten
MDSCD latch pins are within the damage limits given in this service bulletin. Do the inspections again at the
times given in this service bulletin.
At the time given in this service bulletin, Boeing recommends that the 3/16 inch diameter latch pin retention bolts
be replaced with 5/16 inch diameter latch pin retention hardware. As part of this replacement, the retention bolt
holes in the latch pin fittings must be made larger, and new latch pins with larger diameter retention bolt holes
must be installed.
EFFECTIVITY
747-100, 747-200B, 747-200C, 747-200F, 747-300, 747-400, 747-400F, and 747SR Airplanes. Refer to Paragraph
1.A.1., Airplanes, for the list of affected airplanes.
COMPLIANCE
The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to this service
bulletin. The Airworthiness Directive will make the compliance tasks and times given in this service bulletin
mandatory.
Refer to Paragraph 1.E., Compliance.
INDUSTRY SUPPORT INFORMATION
Boeing warranty remedies are not available for the inspections and configuration changes given in this service
bulletin.
MANPOWER
Refer to Paragraph 1.G., Manpower.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 08, 2010
747-52A2294Revision 1: August 16, 2011
10 of 97
BOEING SERVICE BULLETIN 747-52A2294
ALERTALERT

### Page 11 (OCR)

BOEING SERVICE BULLETIN 747-52A2294
ALERT  ALERT
MATERIAL INFORMATION
Boeing Supplied Kits/Parts.
Refer to Paragraph 2.A., Material - Price and Availability.
000000000  NOTE: NUMBERS ADJACENT  TO LATCH PIN FITTINGS
DENOTE LATCH POSITIONS
MAIN DECK
SIDE CARGO
DOOR
DOORWA
000  _OWER SIL  9  10
8
FITTING
2,4,6,8, AND 10
DOORWAY
LOWER
SILL
RETENTION
BOLT  LATCH PIN
FITTING
1,3,5,7, AND 9
A-A
Original Issue: July 08, 2010
Revision 1: August 16, 2011
AT EACH LATCH PIN FITTING LOCATION:
1. DO A DETAILED INSPECTION FOR DAMAGED
LATCH PINS AND LOOSE, BROKEN OR
MISSING RETENTION BOLTS.
2. REMOVE EXISTING RETENTION BOLTS AND
FITTING  LATCH PINS. REWORK LATCH PIN FITTINGS  BY MAKING THE RETENTION BOLT HOLES  1941535
LARGER. INSTALL NEW LATCH PINS AND
RETENTION BOLTS.
747-52A2294
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.  11 of 97

### Page 12

BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 08, 2010
747-52A2294Revision 1: August 16, 2011
12 of 97
BOEING SERVICE BULLETIN 747-52A2294
ALERTALERT
BLANK PAGE

### Page 13

Commercial 
Airplanes
747
Service Bulletin
ALERT
Number: 747-52A2294
Original Issue: July 08, 2010
Revision 1: August 16, 2011
ATA System: 5232
SUBJECT: DOORS - Side Cargo Doors - Main Deck Side Cargo Door Latch Pin and Latch Pin
Retention Bolt Inspection and Modification
THIS BULLETIN IS SENT TO THE OPERATORS OF RECORD OF THE AIRPLANES SHOWN IN PARAGRAPH
1.A., EFFECTIVITY. IF AN AIRPLANE HAS BEEN LEASED OR SOLD, SEND THIS SERVICE BULLETIN TO
THE NEW OPERATOR. IF APPLICABLE SPARES HAVE BEEN SOLD, SEND THIS SERVICE BULLETIN TO
THE NEW OWNER.
1.    PLANNING INFORMATION
A. Effectivity
1. Airplanes
Refer to Service Bulletin Index Document D6-30300 Part 3 for Airplane Variable Number, Line
Number, and Serial Number data.
This service bulletin is for the airplanes shown below.
DESCRIPTIONCONFIGURATIONGROUP
All 747-100, 747-200B, 747-200C, 747-200F, 747SR, 747-300,
747-400, and 747-400F airplanes with a Main Deck Side Cargo Door
(MDSCD) installed in production or by a Boeing-approved
modification, except Group 2 and Group 3 airplanes.
-1
Previously modified in accordance with Boeing Service Bulletin
747-52-2224.
1
Not previously modified in accordance with Boeing Service Bulletin
747-52-2224, or not in the effectivity of Boeing Service Bulletin
747-52-2224.
2
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 08, 2010
747-52A2294Revision 1: August 16, 2011
13 of 97

### Page 14

DESCRIPTIONCONFIGURATIONGROUP
All 747 airplanes that are listed in the effectivity of Boeing Service
Bulletin 747-52-2142.
-2
Previously modified in accordance with Boeing Service Bulletin
747-52-2224.
1
Not previously modified in accordance with Boeing Service Bulletin
747-52-2224.
2
747-200F airplanes R6156 and R6157.-3
Airplane Models:
747-100, 747-200B, 747-200C, 747-200F, 747-300, 747-400, 747-400F, 747SR
GroupVariable Number
1RA002
1RA006
1RA011
1RA015
2RA026
1RA028
2RA029
1RA030
2RA033
2RA101 - RA103
1RA111
2RA112
2RA161 - RA163
1RA401 - RA405
2RA524
1RA631
2RA632
1RA633
2RA634 - RA635
2RA749
1RA750
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 08, 2010
747-52A2294Revision 1: August 16, 2011
14 of 97
BOEING SERVICE BULLETIN 747-52A2294
ALERTALERT

### Page 15

GroupVariable Number
1RA784
2RA901 - RA902
1RA910
2RA911 - RA913
1RA914
2RA915 - RA916
2RB041
2RB043
2RB101 - RB102
1RB411 - RB413
1RB421
1RB604 - RB605
1RB607
1RB696
1RD041 - RD044
1RD055
1RD082 - RD083
1RD142
1RD144
1RD201 - RD204
1RD225
1RD227
1RD233 - RD235
1RD301 - RD302
1RD358
1RD361 - RD366
1RD411 - RD412
1RD433 - RD434
1RD441 - RD442
1RD461
1RD531 - RD533
1RD551
1RD561
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 08, 2010
747-52A2294Revision 1: August 16, 2011
15 of 97
BOEING SERVICE BULLETIN 747-52A2294
ALERTALERT

### Page 16

GroupVariable Number
1RD571
1RD581 - RD583
1RD591 - RD593
2RD601 - RD602
1RD603 - RD607
2RD621 - RD623
2RD641 - RD642
1RD643 - RD649
2RD651
1RD652 - RD659
1RD661
1RD671
2RD681 - RD682
2RD691 - RD692
1RD701 - RD702
1RD721 - RD722
1RD741 - RD742
1RD751 - RD755
1RD761
1RD771 - RD775
1RD781 - RD783
1RD791 - RD792
2RJ301 - RJ302
1RJ303
1RJ321 - RJ322
1RJ331 - RJ333
1RL401 - RL403
1RL411 - RL436
1RL451 - RL456
1RL461 - RL462
1RL471 - RL481
1RL491 - RL492
1RL501 - RL502
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 08, 2010
747-52A2294Revision 1: August 16, 2011
16 of 97
BOEING SERVICE BULLETIN 747-52A2294
ALERTALERT

### Page 17

GroupVariable Number
1RL511 - RL516
1RL521 - RL522
1RL531 - RL534
1RL551
1RL561 - RL568
1RL571 - RL572
1RL576 - RL577
1RL579
1RL581 - RL586
1RL651 - RL655
1RL671 - RL675
1RL681 - RL684
1RL751 - RL752
1RM128
1RM801 - RM803
1RM811 - RM813
1RM851 - RM859
1RM861 - RM863
1RM871 - RM899
1RM901 - RM906
1RM911
1RR005
1RR021 - RR025
1RR031
1RR202 - RR206
2RR221 - RR222
1RR223 - RR226
2RR261
1RR263 - RR267
2RR301 - RR302
1RR303 - RR309
3RR310
1RR331 - RR332
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 08, 2010
747-52A2294Revision 1: August 16, 2011
17 of 97
BOEING SERVICE BULLETIN 747-52A2294
ALERTALERT

### Page 18

GroupVariable Number
1RR336
2RR341 - RR344
1RR345
1RR361 - RR362
1RR421 - RR422
1RR431 - RR432
1RR441 - RR442
1RR451
1RR501 - RR504
1RR521 - RR522
1RR526
1RR531
1RR551 - RR555
3RR556
1RR561
1RR566
1RR701
1RR721 - RR724
1RR746 - RR748
1RR851 - RR856
1RR861 - RR862
1RR951 - RR952
1RS701 - RS703
1RS711 - RS713
1RS721 - RS722
1RS731 - RS732
1RS741 - RS743
1RS751 - RS752
1RS761 - RS762
1RS771
1RS781 - RS782
1RS786
1RT001 - RT014
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 08, 2010
747-52A2294Revision 1: August 16, 2011
18 of 97
BOEING SERVICE BULLETIN 747-52A2294
ALERTALERT

### Page 19

GroupVariable Number
1RT021 - RT022
1RT031 - RT035
1RT041 - RT047
1RT061
1RT071 - RT075
1RT101 - RT103
1RT121
1RT131 - RT137
1RT151 - RT152
1RT161 - RT168
1RT456
1RT461
1RT501
1RT506 - RT510
1RT513
1RT516
1RT518 - RT520
1RT524
1RT528
1RT572 - RT576
1RT642
1RT655 - RT657
1RT751 - RT752
1RT781 - RT782
1RT837
1RT953 - RT954
1RT967
2. Spares Affected
None.
B. Concurrent Requirements
The service bulletin listed below must be done before or at the same time as the modification given in
this service bulletin:
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 08, 2010
747-52A2294Revision 1: August 16, 2011
19 of 97
BOEING SERVICE BULLETIN 747-52A2294
ALERTALERT

### Page 20

DescriptionService BulletinCompany
Inspection for interchanged cargo door latch
pins and installation of pin stop brackets.
747-52-2142, Original issue, Dated May 6,
1977
Boeing
Cargo door latch pin direction inspection.747-52A2258, Original issue, Dated June 1,
1995
Boeing
C. Reason
Accomplishment of the inspections in this service bulletin will ensure that the latch pin retention bolts
in the Main Deck Side Cargo Door lower sill latch pin fittings are not loose, broken or missing. A loose,
broken or missing retention bolt can result in a migrated latch pin, which can become disengaged from
the cargo door latch cams, and lead to increased loads in the adjacent latch pin fittings and latch cams.
Increased loads can cause damage to the cargo door latch mechanism and/or the lower sill structure.
The migration of two or more latch pins and subsequent failure of the latch mechanism or lower sill
structure can result in the inability of the cargo door to carry limit loads, which could lead to the loss of
the cargo door and depressurization of the airplane.
The Main Deck Side Cargo Door has a series of ten latch pin fittings which are attached to the lower
sill of the door cutout and numbered 1 through 10 forward to aft. Latch pins are installed in each latch
pin fitting, and each is secured with a retention bolt. The latch pins and latch pin fittings carry structural
and pressurization loads during flight.
Six operators have reported that broken latch pin retention bolts were found on eight airplanes. On one
airplane, with 101,609 flight-hours and 12,862 flight-cycles, the retention bolts on both the #9 and #10
latch pin fittings were found to be broken. Latch pin #10 was found to have migrated aft and was not
engaging the latch cam. On another airplane, with 33,983 flight-hours and 4,723 flight-cycles, the
retention bolt on the #10 latch pin fitting was found to be broken and the #9 latch pin was found to be
damaged. On another airplane with 67,188 flight-hours and 14,440 flight-cycles, the retention bolt for
the #10 latch pin fitting was found to be completely sheared, which allowed the latch pin to migrate aft
until it no longer engaged the door latch cam. On four airplanes, only the retention bolt on the #10 latch
pin fitting was found to be broken. On one airplane the retention bolt on the #10 latch pin fitting was
found to be damaged.
Revision 1 is sent to change the one-time inspection given in the original issue of this service bulletin
into repeat inspections. Also, instructions for replacement of the 3/16 inch diameter latch pin retention
bolts with 5/16 inch diameter pin retention hardware has been added. This replacement includes
modification of the latch pin fittings and installation of new latch pins. New Figures 10 through 15 have
been added. In addition, Revision 1 identifies another possible configuration for Group 1 and Group 2
airplanes. If the modification given in 747-52-2224 was installed, the configuration of the latch pin
installation at pin fitting position #4 will be different, and similar to position #4 on Group 3 airplanes.
The data given in Information Notice 747-52A2294 IN 01 is included in Revision 1. IN 01 was sent to
clarify that in Figures 4, 5, 7, 8 and 9 it is acceptable to install an additional washer under the nut if
necessary for fastener grip length adjustment.
Boeing Service Related Problem (SRP) 747-SRP-52-0093 is related to this service bulletin.
Boeing Fleet Team Digest article 747-FTD-52-09002 is related to this service bulletin.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 08, 2010
747-52A2294Revision 1: August 16, 2011
20 of 97
BOEING SERVICE BULLETIN 747-52A2294
ALERTALERT

### Page 21

D. Description
Get access to the lower sill of the Main Deck Side Cargo Door (MDSCD) cutout. Do a Detailed Inspection
of all ten latch pin fittings for loose, broken or missing retention bolts and nuts. Measure the latch pins
to make sure they are within allowable limits.
At any latch pin fitting that does not have a loose, broken or missing retention bolt and nut, and the
latch pin is not damaged beyond the limits given in this service bulletin, remove sealant and do a torque
check in accordance with this service bulletin. If the retention bolt passes the torque check, replace
the retention bolt sealant. If the retention bolt fails the torque check, consider the bolt to be broken.
At any latch pin location where the retention bolt and nut was not found to be broken, loose, damaged
or missing, but the latch pin is damaged beyond the limits given in this service bulletin, replace the
latch pin, the retention bolt, and related parts in accordance with this service bulletin.
At any latch pin fitting with a loose, broken or missing retention bolt or nut, do a check for latch pin
migration in accordance with this service bulletin. If the latch pin has not migrated, replace parts at the
affected latch pin fitting location in accordance with this service bulletin. If the latch pin has migrated,
do additional Detailed Inspections of adjacent door and door cutout structure and latch cams within 42
inches of the affected fitting for damage in accordance with this service bulletin. Repair any damage
that is found. Replace parts at the affected latch pin fitting location and any adjacent latch pin fitting
location in accordance with this service bulletin.
The inspection is complete when the retention bolts at all ten latch pin fitting locations have either
passed the torque check or been replaced in accordance with this service bulletin or other Boeing
instructions, and all ten MDSCD latch pins are within the damage limits given in this service bulletin.
Do the inspections again at the times given in this service bulletin.
At the time given in this service bulletin, Boeing recommends that the 3/16 inch diameter latch pin
retention bolts be replaced with 5/16 inch diameter pin retention hardware. As part of this replacement,
the retention bolt holes in the latch pin fittings must be made larger, and new latch pins with larger
diameter retention bolt holes must be installed.
Revision 1 - More work is necessary on airplane(s) inspected in accordance with the original issue of
this service bulletin. Repeat the latch pin retention bolt inspections at the time given in this service
bulletin. In addition, at the time given in this service bulletin, Boeing recommends that the 3/16 inch
diameter latch pin retention bolts be replaced with 5/16 inch diameter pin retention hardware in
accordance with Revision 1.
The work in this service bulletin is done in the maintenance zone(s) given below.
Group 1:
Affected Maintenance Zones
ZoneModel
261, 262747-100, 747-200B, 747-200C,
747-200F, 747-300, 747-400,
747-400F, 747SR
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 08, 2010
747-52A2294Revision 1: August 16, 2011
21 of 97
BOEING SERVICE BULLETIN 747-52A2294
ALERTALERT

### Page 22

Group 2:
Affected Maintenance Zones
ZoneModel
261, 262747-100, 747-200B, 747-200C,
747-200F
Group 3:
Affected Maintenance Zones
ZoneModel
261, 262747-200F
E. Compliance
The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to
this service bulletin. The Airworthiness Directive will make the compliance tasks and times given in this
service bulletin mandatory.
For airplanes that have not yet been modified in accordance with this service bulletin, Boeing
recommends that the inspections in Table 1 and the modifications in Table 2 be done at the times given
in the tables. The inspections in Table 1 are no longer necessary after the modifications in Table 2
have been completed.
After the modifications in Table 2 have been completed, do inspections in accordance with Table 3 at
the times given in Table 3.
Table 1: LATCH PIN FITTING INSPECTIONS
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
-Within 6 months
after the original is-
sue date of this
service bulletin.
Do a Detailed Inspection
of the ten Main Deck Side
Cargo Door (MDSCD)
latch pin retention bolts
and nuts, and measure
the latch pins in accor-
dance with Paragraph
3.A., General Information
and Paragraph 3.B.,
Work Instructions, PART
1.
All affected airplanes
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 08, 2010
747-52A2294Revision 1: August 16, 2011
22 of 97
BOEING SERVICE BULLETIN 747-52A2294
ALERTALERT

### Page 23

Table 1: LATCH PIN FITTING INSPECTIONS
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
-Before further
flight.
Do a torque check of the
retention bolt in accor-
dance with Paragraph
3.A., General Information
and Paragraph 3.B.,
Work Instructions, PART
2.
At any latch pin location
where the retention bolt
and nut was not found to
be loose, broken, damaged
or missing, and the latch
pin is not damaged beyond
the limits given in Para-
graph 3.B., Work Instruc-
tions , PART 1.
--No more work is neces-
sary at that location dur-
ing this inspection inter-
val.
At any latch pin location
where the retention bolt
torque check passed and
the latch pin is not dam-
aged beyond the limits giv-
en in Paragraph 3.B.,
Work Instructions , PART
1.
-Before further
flight.
Consider the bolt to be
broken. Check the latch
pin for migration in accor-
dance with Paragraph
3.A., General Information
and Paragraph 3.B.,
Work Instructions, PART
3.
At any latch pin location
where the retention bolt
torque check failed.
-Before further
flight.
Replace the latch pin, the
retention bolt, and related
parts in accordance with
Paragraph 3.A., General
Information and Para-
graph 3.B., Work Instruc-
tions, PART 4.
At any latch pin location
where the retention bolt
and nut was not found to
be broken, loose, damaged
or missing, but the latch pin
is damaged beyond the
limits given in Paragraph
3.B., Work Instructions ,
PART 1.
-Before further
flight.
Check the latch pin for
migration in accordance
with Paragraph 3.A.,
General Information and
Paragraph 3.B., Work In-
structions, PART 3.
At any latch pin location
where the retention bolt or
nut was found to be bro-
ken, loose, damaged or
missing.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 08, 2010
747-52A2294Revision 1: August 16, 2011
23 of 97
BOEING SERVICE BULLETIN 747-52A2294
ALERTALERT

### Page 24

Table 1: LATCH PIN FITTING INSPECTIONS
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
-Before further
flight.
Do additional Detailed In-
spections of adjacent
door and door cutout
structure and latch cams
within 42 inches of the
affected fitting for dam-
age in accordance with
Paragraph 3.A., General
Information and Para-
graph 3.B., Work Instruc-
tions, PART 3.
At any location with a bro-
ken, loose, damaged or
missing retention bolt or
nut, where the latch pin is
found to be migrated.
-Before further
flight.
Repair damage in accor-
dance with Boeing main-
tenance documents
(Structural Repair Manu-
al, Component Mainte-
nance Manual), or ask
Boeing for repair data
and install the repair. Re-
place the latch pin, the
retention bolt, and related
parts at the affected latch
pin fitting and any adja-
cent latch pin fitting in ac-
cordance with Paragraph
3.A., General Information
and Paragraph 3.B.,
Work Instructions, PART
3 and PART 4.
Damage found during the
Detailed Inspections of ad-
jacent door and door cutout
structure and latch cams,
done in accordance with
Paragraph 3.B., Work In-
structions, PART 3 and
PART 4.
-Before further
flight.
Replace the latch pin, the
retention bolt, and related
parts at the affected latch
pin fitting and any adja-
cent latch pin fitting loca-
tion in accordance with
Paragraph 3.A., General
Information and Para-
graph 3.B., Work Instruc-
tions, PART 3 and PART
4.
No damage found during
the Detailed Inspections of
adjacent door and door
cutout structure and latch
cams, done in accordance
with Paragraph 3.B., Work
Instructions, PART 3 and
PART 4.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 08, 2010
747-52A2294Revision 1: August 16, 2011
24 of 97
BOEING SERVICE BULLETIN 747-52A2294
ALERTALERT

### Page 25

Table 1: LATCH PIN FITTING INSPECTIONS
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
-Before further
flight.
Replace the latch pin, the
retention bolt, and related
parts in accordance with
Paragraph 3.A., General
Information and Para-
graph 3.B., Work Instruc-
tions, PART 4.
At any location with a bro-
ken, loose, damaged or
missing retention bolt or
nut, where the latch pin is
not found to be migrated.
6 months.Within 6 months of
the previous inspec-
tion done in accor-
dance with this
service bulletin.
Repeat the Detailed In-
spection of the ten Main
Deck Side Cargo Door
(MDSCD) latch pin reten-
tion bolts and nuts, and
measure the latch pins in
accordance with Para-
graph 3.A., General Infor-
mation and Paragraph
3.B., Work Instructions ,
PART 1.
All ten MDSCD latch pin
fitting retention bolts have
either passed the torque
check or been replaced in
accordance with Paragraph
3.B., Work Instructions,
PART 4, and all ten MD-
SCD latch pins are within
the damage limit given in
Paragraph 3.B., Work In-
structions , PART 1.
Table 2: LATCH PIN FITTING MODIFICATION AND PIN REPLACEMENT
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
-Within 48 months
after the date on
Revision 1 of this
service bulletin.
Modify the MDSCD latch
pin fittings and replace
the latch pins and latch
pin retention fasteners in
accordance with Para-
graph 3.A., General Infor-
mation and Paragraph
3.B., Work Instructions,
PART 6.
All affected airplanes
--Inspect in accordance
with Table 3.
Airplanes with the modifica-
tion in accordance with
Paragraph 3.B., Work In-
structions, PART 6 accom-
plished.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 08, 2010
747-52A2294Revision 1: August 16, 2011
25 of 97
BOEING SERVICE BULLETIN 747-52A2294
ALERTALERT

### Page 26

Table 3: AFTER-MODIFICATION INSPECTIONS
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
-Within 2 years after
the modification in
accordance with
Paragraph 3.B.,
Work Instructions,
PART 6 was ac-
complished.
Do an Detailed Inspection
of the ten Main Deck Side
Cargo Door (MDSCD)
latch pin retention bolts
and nuts, and measure
the latch pins in accor-
dance with Paragraph
3.A., General Information
and Paragraph 3.B.,
Work Instructions, PART
7. (a)
All affected airplanes with
the modification in accor-
dance with Paragraph 3.B.,
Work Instructions, PART 6
accomplished.
2 years. (a)-Repeat the Detailed In-
spection of the latch pin
retention bolts and nuts,
and measure the latch
pins in accordance with
Paragraph 3.A., General
Information and Para-
graph 3.B., Work Instruc-
tions, PART 7.
At any latch pin location
where the retention bolt
and nut was not found to
be broken, loose, damaged
or missing, and the latch
pin is not damaged beyond
the limits given in Para-
graph 3.B., Work Instruc-
tions, PART 7.
-Before further
flight.
Replace the latch pin, the
retention bolt, and related
parts in accordance with
Paragraph 3.A., General
Information and Para-
graph 3.B., Work Instruc-
tions, PART 7.
At any latch pin location
where the retention bolt
and nut was not found to
be broken, loose, damaged
or missing, but the latch pin
is damaged beyond the
limits given in Paragraph
3.B., Work Instructions,
PART 7.
-Before further
flight.
Check the latch pin for
migration in accordance
with Paragraph 3.A.,
General Information and
Paragraph 3.B., Work In-
structions, PART 7.
At any latch pin location
where the retention bolt or
nut was found to be bro-
ken, loose, damaged or
missing.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 08, 2010
747-52A2294Revision 1: August 16, 2011
26 of 97
BOEING SERVICE BULLETIN 747-52A2294
ALERTALERT

### Page 27

Table 3: AFTER-MODIFICATION INSPECTIONS
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
-Before further
flight.
Do additional Detailed In-
spections of adjacent
door and door cutout
structure and latch cams
within 42 inches of the
affected fitting for dam-
age in accordance with
Paragraph 3.A., General
Information and Para-
graph 3.B., Work Instruc-
tions, PART 7.
At any location with a bro-
ken, loose, damaged or
missing retention bolt or
nut, where the latch pin is
found to be migrated.
-Before further
flight.
Repair the damage in ac-
cordance with Boeing
maintenance documents
(Structural Repair Manu-
al, Component Mainte-
nance Manual) or ask
Boeing for repair data
and install the repair. Re-
place the latch pin, the
retention bolt, and related
parts at the affected latch
pin fitting and any adja-
cent latch pin fitting in ac-
cordance with Paragraph
3.A., General Information
and Paragraph 3.B.,
Work Instructions, PART
7.
Damage found during the
Detailed Inspections of ad-
jacent door and door cutout
structure and latch cams,
done in accordance with
Paragraph 3.B., Work In-
structions, PART 7.
-Before further
flight.
Replace the latch pin, the
retention bolt, and related
parts at the affected latch
pin fitting and any adja-
cent latch pin fitting loca-
tion in accordance with
Paragraph 3.A., General
Information and Para-
graph 3.B., Work Instruc-
tions, PART 7.
No damage found during
the Detailed Inspections of
adjacent door and door
cutout structure and latch
cams, done in accordance
with Paragraph 3.B., Work
Instructions, PART 7.
-Before further
flight.
Replace the latch pin, the
retention bolt, and related
parts in accordance with
Paragraph 3.A., General
Information and Para-
graph 3.B., Work Instruc-
tions, PART 7.
At any location with a bro-
ken, loose, damaged or
missing retention bolt or
nut, where the latch pin is
not found to be migrated.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 08, 2010
747-52A2294Revision 1: August 16, 2011
27 of 97
BOEING SERVICE BULLETIN 747-52A2294
ALERTALERT

### Page 28

Table 3: AFTER-MODIFICATION INSPECTIONS
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
2 years.-Repeat the Detailed In-
spection of the latch pin
retention bolts and nuts,
measure the latch pins,
and check for latch pin
migration in accordance
with Paragraph 3.A.,
General Information and
Paragraph 3.B., Work In-
structions, PART 7.
At any latch pin location
where the latch pin, the re-
tention bolt, or related parts
were replaced in accor-
dance with Paragraph 3.B.,
Work Instructions, PART 7.
(a) This is expected to create an additional task card to be added to the operator's maintenance
program.
F. Approval
This service bulletin was examined by the Federal Aviation Administration (FAA). The changes specified
in this service bulletin comply with the applicable regulations and are FAA approved, as well as European
Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved
airplanes listed in the service bulletin effectivity. This service bulletin and its approval were based on
the airplane in its original Boeing delivery configuration or as modified by other approved Boeing
changes.
If an airplane has a non-Boeing modification or repair that affects a component or system also affected
by this service bulletin, the operator is responsible for obtaining appropriate regulatory agency approval
before incorporating this service bulletin.
G. Manpower
The table below shows an estimate of the task hours necessary to do this inspection for each airplane.
This estimate is for direct labor only, done by an experienced crew. Adjust the estimate with operator
task hour data if necessary. The estimate does not include lost time. These are some examples of lost
time:
 Time to adjust to the workplace
 Time to schedule the work
 Time to inspect the work
 Time to cure the materials
 Time to make the parts
 Time to find the tools.
Table 1 - Inspection
Elapsed HoursTask HoursNumber of PersonsTask
0.100.101Open Access
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 08, 2010
747-52A2294Revision 1: August 16, 2011
28 of 97
BOEING SERVICE BULLETIN 747-52A2294
ALERTALERT

### Page 29

Table 1 - Inspection
Elapsed HoursTask HoursNumber of PersonsTask
1.001.001Detailed Inspection
(Figure 1)
2.002.001Torque Check (Fig-
ure 2)
0.100.101Close Access
3.203.20TOTAL FOR EACH AIRPLANE
NOTE: More time will be necessary for additional inspections and part replacement if damage is
found.
Table 2 - Modification
Elapsed HoursTask HoursNumber of PersonsTask
0.100.101Open Access
1.001.001Modification (Latch
Fitting #1 - Figure
10)
1.251.251Modification (Latch
Fitting #2 - Figure 14
or 15)
1.001.001Modification (Latch
Fitting #3 - Figure
10)
0.750.751Modification (Latch
Fitting #4 - Figure
11)
0.750.751Modification (Latch
Fitting #5 - Figure
12)
1.001.001Modification (Latch
Fitting #6 - Figure
13)
1.001.001Modification (Latch
Fitting #7 - Figure
10)
1.001.001Modification (Latch
Fitting #8 - Figure
10)
1.001.001Modification (Latch
Fitting #9 - Figure
10)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 08, 2010
747-52A2294Revision 1: August 16, 2011
29 of 97
BOEING SERVICE BULLETIN 747-52A2294
ALERTALERT

### Page 30

Table 2 - Modification
Elapsed HoursTask HoursNumber of PersonsTask
1.001.001Modification (Latch
Fitting #10 - Figure
10)
0.100.101Close Access
0.750.751Test
10.7010.70TOTAL FOR EACH AIRPLANE
NOTE: More time will be necessary for additional inspections and part replacement if damage is
found.
Table 3 - After-Modification Inspection
Elapsed HoursTask HoursNumber of PersonsTask
0.100.101Open Access
1.001.001Detailed Inspection
(Figure 1)
0.100.101Close Access
1.201.20TOTAL FOR EACH AIRPLANE
NOTE: More time will be necessary for additional inspections and part replacement if damage is
found.
H. Weight and Balance Changes
None.
I. Electrical Load Data
Not changed.
J. References
1. Existing Data
a. Boeing Service Letter 747-SL-51-048
b. Boeing Service Related Problem (SRP) 747-SRP-52-0093
c. 747-100/200/300 Aircraft Maintenance Manual (AMM) 52-32-00
d. 747-400 Aircraft Maintenance Manual (AMM) 52-32-00
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 08, 2010
747-52A2294Revision 1: August 16, 2011
30 of 97
BOEING SERVICE BULLETIN 747-52A2294
ALERTALERT

### Page 31

e. Boeing Service Bulletins 747-52-2105 , "Cargo Door Latch and Lock System Revision,"
747-52-2142, "Main Deck and Lower Lobe Cargo Door Latch Pin Inspection and Fitting
Modification," 747-52-2224 , "Doors - Cargo Doors - Door Warning - Forward and Aft Lower
Lobe and Main Deck Side Cargo Door Warning System Revision" and 747-52A2258 , "Doors
- Cargo Doors - Latch Pin Direction Inspection"
f. Engineering Change Memo PRR 85901-112RS
g. Standard Overhaul Practices Manual (SOPM) 20-10-01, 20-10-02, 20-50-10
h. 747-100/200/300 Structural Repair Manual (SRM) 51, 52, 53, 53-40-01
i. 747-400 Structural Repair Manual (SRM) 51, 52, 53, 53-00-90
j. 747-400F Structural Repair Manual (SRM) 51, 52, 53, 53-00-90
k. 747-400SF Structural Repair Manual (SRM) 51, 52, 53, 53-00-90
l. Overhaul Manual (OHM) 52-36-75, 52-36-76
2. Data supplied with this Service Bulletin
a. Drawings:
ADCNDCN/REVSheetTitleDrawing No
--1Misc Tool Cargo Door Latch Pin Fitting Re-
work Tool
MIT140U8005
--2
3. Installation Drawings Used in the Preparation of this Service Bulletin
TitleDrawing Number
Sill Instl - Lower, Main Deck Cargo Door65B17670
This drawing was used to prepare this service bulletin. This drawing is not necessary to make the
specified changes, and is not supplied with this service bulletin. This drawing may not be applicable
to all airplane configurations or operators.
K. Publications Affected
1. Publications:
Chapter-SectionPublication
53-12747 Illustrated Parts Catalog
53-12747-400 Illustrated Parts Catalog
2. Damage Tolerance Based Structural Inspections:
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 08, 2010
747-52A2294Revision 1: August 16, 2011
31 of 97
BOEING SERVICE BULLETIN 747-52A2294
ALERTALERT

### Page 32

Boeing has evaluated the repairs and/or changes in this service bulletin for effects on Fatigue
Critical Structure (FCS) and for changes to Damage Tolerance Inspections (DTI) required in the
Maintenance Program. This service bulletin affects FCS. DTI requirements for the structure affected
are contained in Paragraph 1.E., Compliance of this service bulletin.
L. Interchangeability and Intermixability of Parts
Accomplishment of this service bulletin does not affect interchangeability or intermixability of parts.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 08, 2010
747-52A2294Revision 1: August 16, 2011
32 of 97
BOEING SERVICE BULLETIN 747-52A2294
ALERTALERT

### Page 33

2.    MATERIAL INFORMATION
A. Material - Price and Availability
Boeing can supply the kits shown in Paragraph 2.C., Parts Necessary for Each Airplane. Operators
are encouraged to share schedule requirements with Boeing for incorporation of the service bulletin.
The kits are subject to the terms and conditions of the Boeing standard purchase order acknowledgment.
Prices are in United States Dollars. Terms: Net 30 days.
Reference this service bulletin and submit your purchase order by one of these methods:
1. Order on-line via ATA Spec 2000 or The Boeing PART Page
2. Fax to (206) 662-7145
REFER TO THE BOEING PART PAGE ON MYBOEINGFLEET.COM OR CONTACT FIRST RESPONDER
AT FR@BOEING.COM FOR THE LATEST REORDER LEAD TIME (ROLT) AND PRICE INFORMATION
Unit Price as of
the Revision 1
date of this Ser-
vice Bulletin (US
Dollars)
ROLT as of the
Revision 1 date of
this Service Bul-
letin (Calendar
Days)
QTYDateNameKit Number
$11,4783829May 12, 2010Top Kit - Inspection015U1899-1
15July 14, 2010
$12,2543821May 13, 2010Top Kit - Inspection015U1899-2
$5,5304311July 21, 2011Top Kit - Modification015U1916-1
14August 4, 2011
B. Industry Support Information
Boeing warranty remedies are not available for the inspections and configuration changes given in this
service bulletin.
C. Parts Necessary For Each Airplane
1. Kits/Parts
To get the kits/parts shown below, refer to Paragraph 2.A., Material - Price and Availability.
NOTE: One top kit and the items shown in Paragraph 2.C.2., Parts and Materials Supplied by
the Operator, include the parts that may be necessary for each airplane, if damage is
found.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 08, 2010
747-52A2294Revision 1: August 16, 2011
33 of 97
BOEING SERVICE BULLETIN 747-52A2294
ALERTALERT

### Page 34

Kit 015U1899
NotesExisting Part
Number
NameQTYNew Part Number
-2-1
--Top Kit - Inspection
- Group 1 and
Group 2
.-015U1899-1
--Top Kit - Inspection
- Group 3
-.015U1899-2
(a) (b)146U6107-1SWITCH STRIKER1.146U6107-1
(a)69B15457-7PIN9969B15457-7
(a)69B15457-8PIN1169B15457-8
(a) (b)69B18044-1BRACKET1169B18044-1
(a) (b)69B18044-2BRACKET7769B18044-2
(c)-BOLT910BACB30LM3-27
(c)-BOLT, HEX HEAD1.BACB30NM3K34
--NUT910BACN10JC3CD
--NUT1.BACN10YR3CD
--WASHER1.BACW10BP3DP
--WASHER, PLAIN1010NAS1149E0332P
(a) This part is used for Production
(b) You can use the existing part to replace the new or changed part
(c) If grip length shown is not available at Boeing, fasteners supplied in kits may
be one grip length longer than indicated. Also, if any fasteners part numbers
listed are not available or have been superseded, substitute fasteners may be
supplied in kits. Boeing Document D-590 and Boeing Drawing 012W6100 are
used to determine the part numbers used as substitutes.
Kit 015U1916
NotesExisting Part
Number
NameQTYNew Part Number
-1
--Top Kit - Modifica-
tion
-015U1916-1
(a) (b)
(c)
69B15457-7PIN-LATCH9146U8355-1
(a) (b)
(c)
69B15457-8PIN-LATCH1146U8355-2
(a) (b)
(c)
69B18044-2PIN STOP
BRACKET
7146U8356-1
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 08, 2010
747-52A2294Revision 1: August 16, 2011
34 of 97
BOEING SERVICE BULLETIN 747-52A2294
ALERTALERT

### Page 35

Kit 015U1916
NotesExisting Part
Number
NameQTYNew Part Number
-1
(a) (b)
(c)
69B18044-1PIN STOP
BRACKET
1146U8356-2
(d)-BOLT, HEX HEAD10BACB30LJ5K28
(d)-BOLT, HEX HEAD1BACB30LJ5K34
--NUT10BACN10YR5CD
(d)-WASHER-PLAIN22BACW10BP5DP
(a) Keep the existing part if there are other uses for it.
(b) This part is used for Production
(c) You cannot use the existing part to replace the new or changed part
(d) If grip length shown is not available at Boeing, fasteners supplied in kits
may be one grip length longer than indicated. Also, if any fasteners part
numbers listed are not available or have been superseded, substitute
fasteners may be supplied in kits. Boeing Document D-590 and Boeing
Drawing 65B88700 are used to determine the part numbers used as
substitutes.
2. Parts and Materials Supplied by the Operator
NotesNameQTYPart Number /
Specification
(a) (b)Sealant8
ounces
BMS 5-95
For Group 3 only. Refer to
FIGURE 6.
Washer2BACW10BP3DP
(a) See the Qualified Products List at the end of the Boeing Material Specification (BMS) for
supplier data.
(b) The number in the QTY column assumes that parts replacement is required at all ten af-
fected latch pin fitting locations. The actual quantity necessary will depend upon inspection
results.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 08, 2010
747-52A2294Revision 1: August 16, 2011
35 of 97
BOEING SERVICE BULLETIN 747-52A2294
ALERTALERT

### Page 36

3. Parts Modified and Reidentified
NotesNew Part Number
(b) (c)
NameQTYExisting Part
Number
Optional to
69B15457-5 or
69B15457-7. (a)
146U8355-1Latch Pin169B15457-3
Optional to
69B15457-3 or
69B15457-7. (a)
69B15457-5
Optional to
69B15457-3 or
69B15457-5. (a)
69B15457-7
Optional to
69B15457-4 or
69B15457-6. (a)
146U8355-2Latch Pin169B15457-2
Optional to
69B15457-2 or
69B15457-6. (a)
69B15457-4
Optional to
69B15457-2 or
69B15457-4. (a)
69B15457-6
(a) Make the change in accordance with FIGURE 16 of this service bulletin.
(b) This is the part number after the change is done in accordance with this service bulletin.
(c) This part is used in production.
None.
4. Parts Removed and Not Replaced
None.
D. Parts Necessary to Change Spares
None.
E. Special Tooling - Price and Availability
Boeing can supply the tool shown in Paragraph 2.F., Special Tooling Necessary to do this Service
Bulletin. Operators are encouraged to share schedule requirements with Boeing for incorporation of
the service bulletin by e-mail to ServiceBulletinRentalLoanTools@boeing.com. The tool is subject to
the terms and conditions of the Boeing standard purchase order acknowledgement. Prices are in United
States dollars. Terms: Net 30 days.
Reference this service bulletin and submit your purchase order by one of these methods:
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 08, 2010
747-52A2294Revision 1: August 16, 2011
36 of 97
BOEING SERVICE BULLETIN 747-52A2294
ALERTALERT

### Page 37

1. Order on-line via ATA Spec 2000 or Boeing Part Page
2. Fax to (425) 965-8237
Rental Data:
Daily Price as of
the Revision 1
date of this ser-
vice bulletin (US
Dollars)
NameTool Kit Number
(a)Cargo Door Latch Pin Fitting
Rework Tool
MIT140U8005-1
(a) Pricing data was not available at the time of release of this service
bulletin. Refer to the Boeing PART page on MyBoeingFleet.com or
contact First Responder at fr@boeing.com for the latest price infor-
mation.
F. Special Tooling Necessary to do this Service Bulletin
To get the tools shown below, refer to Paragraph 2.E., Special Tooling - Price and Availability.
Maintenance and overhaul tools in the manuals shown in Paragraph 1.J., References, can also be
necessary. Examine operator tool supply to make sure all necessary tools are available.
NameTool Kit Number
Cargo Door Latch Pin Fitting
Rework Tool
MIT140U8005-1
NOTE: Reamer Kit MIT140U8005-14, which is a component of Tool Kit MIT140U8005-1, can be
ordered if additional reamers are needed.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 08, 2010
747-52A2294Revision 1: August 16, 2011
37 of 97
BOEING SERVICE BULLETIN 747-52A2294
ALERTALERT

### Page 38

BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 08, 2010
747-52A2294Revision 1: August 16, 2011
38 of 97
BOEING SERVICE BULLETIN 747-52A2294
ALERTALERT
BLANK PAGE

### Page 39

3.    ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL INFORMATION
CAUTION: KEEP THE WORK AREA, WIRES AND ELECTRICAL BUNDLES CLEAN OF METAL
PARTICLES OR CONTAMINATION WHEN YOU USE TOOLS. UNWANTED MATERIAL,
METAL PARTICLES OR CONTAMINATION CAUGHT IN WIRE BUNDLES CAN CAUSE
DAMAGE TO THE BUNDLES. DAMAGED WIRE BUNDLES CAN CAUSE SPARKS OR
OTHER ELECTRICAL DAMAGE.
NOTE: 1. Manual titles are referred to by acronyms. Refer to Paragraph 1.J., References, for
definition of the acronyms.
2. Obey all of the warnings and cautions given in the specified manual sections.
3. Unless shown differently, these dimensions and tolerances are used:
– Linear dimensions are in inches
– Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus
or minus 0.03 inch
– Tolerance on rivet and bolt edge margin is plus or minus 0.05 inch
– Angular tolerance is plus or minus 2 degrees
– Hole dimensions for standard solid rivets and fasteners are in Structural Repair
Manual (SRM) Chapter 51
– Torque limits to tighten nuts and bolts are in SRM Chapter 51
4. Use the approved fastener and process material substitutions in accordance with
SRM Chapter 51.
5. If the length of any fastener specified in this service bulletin does not meet installation
standards given in SRM Chapter 51, then a fastener of the same specification, or
an approved substitute, with a length which meets the installation standards given
in SRM Chapter 51 may be used. In addition, washers may be installed for fastener
grip length in accordance with SRM Chapter 51.
6. Boeing Service Letter 747-SL-51-048, Damage Reporting and Repair Plan/Design
Guidelines, is an acceptable procedure to request information from Boeing for
additional structural repair instructions. The Service Letter describes what information
must be provided to Boeing before a structural repair can be provided.
7. These work instructions refer to procedures included in other Boeing documents.
When the words "refer to" are used and the operator has an accepted alternative
procedure, the accepted alternative procedure can be used. When the words "in
accordance with" are included in the instruction, the procedure in the Boeing document
must be used.
8. A Detailed Inspection is defined as: An intensive examination of a specific item,
installation, or assembly to detect damage, failure, or irregularity. Available lighting
is normally supplemented with a direct source of good lighting at an intensity deemed
appropriate. Inspection aids such as mirrors, magnifying lenses, etc. may be
necessary. Surface cleaning and elaborate procedures may be required.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 08, 2010
747-52A2294Revision 1: August 16, 2011
39 of 97
BOEING SERVICE BULLETIN 747-52A2294
ALERTALERT

### Page 40

9. The instructions in Paragraph 3.B., Work Instructions and the figures can include
operation of tools or test equipment. Boeing Engineering Tool Drawings, the Illustrated
Tool and Equipment Manual, and the Special Tool and Ground Handling Drawing
Index contain data on versions of the tools or test equipment that you can use. It is
permitted to use replaced tools. It is not permitted to use superseded tools.
10. If it is necessary to remove more parts for access, you can remove those parts. If
you can get access without removing identified parts, it is not necessary to remove
all of the identified parts. Jacking and shoring limitations must be observed.
11. Where the work instructions include installation of a kept part, a new or serviceable
part with the same part number can be installed as an alternative to the kept part.
The removed part can be discarded if a new or serviceable part is installed.
12. Some Boeing parts are supplied in a temporary configuration. Those parts are
identified with a 'U', 'W', or 'Y' in place of the '-' (dash) in the part number. It is
permitted to install parts identified with a 'U', 'W', or 'Y' as an alternative to the '-'
(dash) part number. Boeing Drawing 005W0900 contains more data.
B. WORK INSTRUCTIONS
PART 1 - Latch Pin Retention Bolt and Latch Pin Inspection
1. Open the Main Deck Side Cargo Door (MDSCD) as necessary to get access to the latch pin fittings
(10 locations) on the lower sill of the door cutout. Refer to 747-100/200/300 AMM 52-32-00 or
747-400 AMM 52-32-00 as accepted procedures.
2. Do a Detailed Inspection of the MDSCD latch pin retention nuts and bolts and measure the latch
pins in accordance with FIGURE 1.
3. At any MDSCD latch pin fitting location where the retention bolt and nut was not found to be loose,
broken, damaged or missing, and the latch pin is not damaged beyond the limits given in FIGURE
1, do a torque check of the retention bolt in accordance with PART 2.
4. At any MDSCD latch pin fitting location where the retention bolt and nut was not found to be loose,
broken, damaged or missing, but the latch pin is damaged beyond the limits given in FIGURE 1,
replace the latch pin, retention bolt, and related parts in accordance with PART 4.
5. At any MDSCD latch pin fitting location where the retention bolt or nut was found to be broken,
loose, damaged or missing, check the latch pin for migration in accordance with PART 3.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 08, 2010
747-52A2294Revision 1: August 16, 2011
40 of 97
BOEING SERVICE BULLETIN 747-52A2294
ALERTALERT

### Page 41

PART 2 - Torque Check
1. Do a torque check on the MDSCD latch pin retention bolt on the latch pin fitting in accordance with
FIGURE 2.
2. At any latch pin location where the retention bolt fails the torque check (the bolt or nut cannot resist
the applied torque), consider the bolt to be broken. Check the latch pin for migration in accordance
with PART 3.
3. At any latch pin location where the retention bolt passes the torque check (the bolt or nut resists
the applied torque), reapply BMS 5-95 sealant to the retention bolt head (or nut, as applicable).
4. Continue to PART 5.
PART 3 - Inspection for Latch Pin Migration
1. At any latch pin fitting location where the torque check failed or the retention bolt or nut was found
to be broken, loose, damaged or missing:
a. If any parts were found to be missing, to prevent foreign object damage do a search for the
missing parts in the vicinity of the affected latch pin fitting on the lower sill and on the ground
below.
b. Check the position of the latch pin in accordance with FIGURE 3 to determine if the latch pin
has migrated from its nominal installed position.
c. If the latch pin has migrated, do the steps that follow:
(1) Do Detailed Inspections of the latch pin fitting and the adjacent (forward and aft) latch
pin fittings, the door cutout structure within 42 inches of the affected latch pin fitting, the
affected latch cam and the adjacent (forward and aft) latch cams on the door, and the
door structure within 42 inches of the affected latch cam for damage. Remove linings and
cargo handling equipment as necessary for access.
NOTE: The Detailed Inspections are intended to find distressed fasteners, deformation
in structure, cracks, and other damage.
(2) Repair any damage that is found as listed below. As an alternative to repair, replace
damaged parts or ask Boeing for repair data and install the repair.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 08, 2010
747-52A2294Revision 1: August 16, 2011
41 of 97
BOEING SERVICE BULLETIN 747-52A2294
ALERTALERT

### Page 42

(a) Repair fuselage structure in accordance with SRM Chapter 53. Repair door structure
in accordance with SRM Chapter 52
(b) Repair latch pin fittings in accordance with 747-100/200/300 SRM 53-40-01, 747-400
SRM 53-00-90 Repair 1, 747-400F SRM 53-00-90 Repair 1, or 747-400SF SRM
53-00-90 Repair 1.
(c) Components of the Main Deck Side Cargo Door mechanisms can be repaired in
accordance with OHM 52-36-75 or OHM 52-36-76
(3) Disassemble and replace the latch pin, retention bolt, and related parts in accordance
with PART 4. If not already replaced during this inspection, also disassemble and replace
the latch pin, retention bolt, and related parts at any latch pin fitting location adjacent to
(one fitting position forward and aft of) the migrated latch pin location in accordance with
PART 4.
d. If the latch pin has not migrated, disassemble and replace the latch pin, retention bolt, and
related parts in accordance with PART 4.
2. Continue to PART 5.
PART 4 - Disassembly and Replacement
1. At any latch pin fitting location where the retention bolt or nut was found to be broken or loose, or
where a retention bolt failed the torque check, or where the latch pin is damaged beyond the limits
given in FIGURE 1, disassemble, inspect and install new parts in accordance with:
a. All Groups:
FIGURE 4, for latch pin fitting positions #1, #3, #7, #8, #9 and #10.
FIGURE 7, for latch pin fitting position #4.
FIGURE 8, for latch pin fitting position #5.
FIGURE 9, for latch pin fitting position #6.
b. Group 1-2, Configuration 2:
FIGURE 5, for latch pin fitting position #2.
c. Group 1-2, Configuration 1; Group 3:
FIGURE 6, for latch pin fitting position #2.
Repair any damage that is found as listed below. As an alternative to repair, replace damaged
parts or ask Boeing for repair data and install the repair.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 08, 2010
747-52A2294Revision 1: August 16, 2011
42 of 97
BOEING SERVICE BULLETIN 747-52A2294
ALERTALERT

### Page 43

a. Repair fuselage structure in accordance with SRM Chapter 53. Repair door structure in
accordance with SRM Chapter 52
b. Repair latch pin fittings in accordance with 747-100/200/300 SRM 53-40-01, 747-400 SRM
53-00-90 Repair 1, 747-400F SRM 53-00-90 Repair 1, or 747-400SF SRM 53-00-90 Repair
1.
c. Components of the Main Deck Side Cargo Door mechanisms can be repaired. Refer to OHM
52-36-75 and OHM 52-36-76 as accepted procedures.
2. Continue to PART 5
PART 5 - Restoration
1. If any latch pin fitting was removed from the airplane, adjust the MDSCD. Refer to the task
"Adjustment - Side Cargo Door System" in 747-100/200/300 AMM 52-32-00 or "Adjustment - Side
Cargo Door" in 747-400 AMM 52-32-00 as accepted procedures.
2. After all ten MDSCD latch pin fitting retention bolts have either passed the torque check in
accordance with PART 2 or been replaced in accordance with PART 4, and all ten MDSCD latch
pins are within the damage limit given in FIGURE 1 , close the MDSCD electrically. Refer to
747-100/200/300 AMM 52-32-00 or 747-400 AMM 52-32-00 as accepted procedures. Make sure
that the latch cams turn freely and engage and disengage the latch pins during normal operation.
3. Put the airplane back to a serviceable condition. Do the inspection again at the time given in
Paragraph 1.E., Compliance , Table 1. Modify the latch pin installations in accordance with PART
6 at the time given in Paragraph 1.E., Compliance , Table 2.
PART 6 - Modification
1. Open the Main Deck Side Cargo Door (MDSCD) as necessary to get access to the latch pin fittings
(10 locations) on the lower sill of the door cutout. Refer to 747-100/200/300 AMM 52-32-00 or
747-400 AMM 52-32-00 as accepted procedures.
NOTE: If not previously accomplished, Boeing recommends that the MDSCD modification in
Boeing Service Bulletin 747-52-2224 be installed prior to or at the same time as the
modification in this service bulletin. Service Bulletin 747-52-2224 changes the configuration
at latch pin fitting position #2.
2. Disassemble, inspect, and modify the latch pin fitting, and install new parts in accordance with:
a. All Groups:
FIGURE 10, for latch pin fitting positions #1, #3, #7, #8, #9 and #10.
FIGURE 11, for latch pin fitting position #4.
FIGURE 12, for latch pin fitting position #5.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 08, 2010
747-52A2294Revision 1: August 16, 2011
43 of 97
BOEING SERVICE BULLETIN 747-52A2294
ALERTALERT

### Page 44

FIGURE 13, for latch pin fitting position #6.
b. Group 1-2, Configuration 2:
FIGURE 14, for latch pin fitting position #2.
c. Group 1-2, Configuration 1; Group 3:
FIGURE 15, for latch pin fitting position #2.
NOTE: Existing 69B15457-3, -4, -5, -6, -7, and -8 latch pins can be reworked in accordance with
FIGURE 16. Existing 69B15457-1 and -2 latch pins must first be reworked into 69B15457-3
and -4 latch pins in accordance with Boeing Service Bulletin 747-52-2105, "Cargo Door
Latch and Lock System Revision".
3. If any latch pin fitting was removed from the airplane, adjust the MDSCD. Refer to the task
"Adjustment - Side Cargo Door System" in 747-100/200/300 AMM 52-32-00 or "Adjustment - Side
Cargo Door" in 747-400 AMM 52-32-00 as accepted procedures.
4. Close the MDSCD electrically. Refer to 747-100/200/300 AMM 52-32-00 or 747-400 AMM 52-32-00
as accepted procedures. Make sure that the latch cams turn freely and engage and disengage
the latch pins during normal operation.
5. Put the airplane back to a serviceable condition. After modification of all 10 latch pin fittings, start
to do inspections in accordance with PART 7 at the times given in Paragraph 1.E., Compliance,
Table 3.
PART 7 - After-Modification Inspection
1. Open the Main Deck Side Cargo Door (MDSCD) as necessary to get access to the latch pin fittings
(10 locations) on the lower sill of the door cutout. Refer to 747-100/200/300 AMM 52-32-00 or
747-400 AMM 52-32-00 as accepted procedures.
2. Do a Detailed Inspection of the MDSCD latch pin retention nuts and bolts, inspect for damage or
corrosion, and measure the latch pins in accordance with FIGURE 1.
3. At any MDSCD latch pin fitting location where the retention bolt and nut was not found to be loose,
broken or missing, but the latch pin is damaged beyond the limits given in FIGURE 1, replace the
latch pin, retention bolt, and related parts in accordance with PART 6.
NOTE: PART 6 includes instructions to modify the latch pin fittings by making the retention bolt
holes in the latch pin fittings larger. This latch pin fitting modification is only necessary
the first time PART 6 is accomplished.
4. At any MDSCD latch pin fitting location where the retention bolt or nut was found to be broken,
loose, damaged or missing, check the latch pin for migration in accordance with the steps that
follow:
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 08, 2010
747-52A2294Revision 1: August 16, 2011
44 of 97
BOEING SERVICE BULLETIN 747-52A2294
ALERTALERT

### Page 45

a. If any parts were found to be missing, to prevent foreign object damage do a search for the
missing parts in the vicinity of the affected latch pin fitting on the lower sill and on the ground
below.
b. Check the position of the latch pin in accordance with FIGURE 3 to determine if the latch pin
has migrated from its nominal installed position.
c. If the latch pin has migrated, do the steps that follow:
(1) Do Detailed Inspections of the latch pin fitting and the adjacent (forward and aft) latch
pin fittings, the door cutout structure within 42 inches of the affected latch pin fitting, the
affected latch cam and the adjacent (forward and aft) latch cams on the door, and the
door structure within 42 inches of the affected latch cam for damage. Remove linings and
cargo handling equipment as necessary for access.
NOTE: The Detailed Inspections are intended to find distressed fasteners, deformation
in structure, cracks, and other damage.
(2) Repair any damage that is found as listed below. As an alternative to repair, replace
damaged parts or ask Boeing for repair data and install the repair.
(a) Repair fuselage structure in accordance with SRM Chapter 53. Repair door structure
in accordance with SRM Chapter 52
(b) Repair latch pin fittings in accordance with 747-100/200/300 SRM 53-40-01, 747-400
SRM 53-00-90 Repair 1, 747-400F SRM 53-00-90 Repair 1, or 747-400SF SRM
53-00-90 Repair 1.
(c) Components of the Main Deck Side Cargo Door mechanisms can be repaired. Refer
to OHM 52-36-75 and OHM 52-36-76 as accepted procedures.
(3) Disassemble and replace the latch pin, retention bolt, and related parts in accordance
with PART 6. If not already replaced, also disassemble and replace the latch pin, retention
bolt, and related parts at any latch pin fitting location adjacent to (one fitting position
forward and aft of) the migrated latch pin location in accordance with PART 6.
NOTE: PART 6 includes instructions to modify the latch pin fittings by making the
retention bolt holes in the latch pin fittings larger. This latch pin fitting modification
is only necessary the first time PART 6 is accomplished.
d. If the latch pin has not migrated, disassemble and replace the latch pin, retention bolt, and
related parts in accordance with PART 6.
NOTE: PART 6 includes instructions to modify the latch pin fittings by making the retention
bolt holes in the latch pin fittings larger. This latch pin fitting modification is only
necessary the first time PART 6 is accomplished.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 08, 2010
747-52A2294Revision 1: August 16, 2011
45 of 97
BOEING SERVICE BULLETIN 747-52A2294
ALERTALERT

### Page 46

5. If any latch pin fitting was removed from the airplane, adjust the MDSCD. Refer to the task
"Adjustment - Side Cargo Door System" in 747-100/200/300 AMM 52-32-00 or "Adjustment - Side
Cargo Door" in 747-400 AMM 52-32-00 as accepted procedures.
6. Close the MDSCD electrically. Refer to 747-100/200/300 AMM 52-32-00 or 747-400 AMM 52-32-00
as accepted procedures. Make sure that the latch cams turn freely and engage and disengage
the latch pins during normal operation.
7. Put the airplane back to a serviceable condition. Continue to do inspections in accordance with
PART 7 at the times given in Paragraph 1.E., Compliance, Table 3.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 08, 2010
747-52A2294Revision 1: August 16, 2011
46 of 97
BOEING SERVICE BULLETIN 747-52A2294
ALERTALERT

### Page 47 (OCR)

BOEING SERVICE BULLETIN 747-52A2294
ALERT  ALERT
000000000  NOTE: NUMBERS ADJACENT  TO LATCH PIN FITTINGS
DENOTE LATCH POSITIONS
MAIN DECK
SIDE CARGO
0000  DOOR  DOORWAY
000  LOWER SILL  9  10
8
FITTING
2,4,6,8, & 10
DOORWAY
LOWER
SILL
LATCH PIN
FITTING
• 1,3,5,7, & 9
LATCH PIN RETENTION BRACKETS
NOT SHOWN
SEALANT  A-A  FITTING  1941570
FIGURE 1: DETAILED INSPECTION
(SHEET 1 OF 2)
Original Issue: July 08, 2010
Revision 1 August 16, 2011  BOEING PROPRIETARY -  747-52A2294
Copyright © Unpublished Work - See page 1 for details.  47 of 97

### Page 48

The step number shown below agrees with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for one latch pin fitting location.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
Measure the diame-
ter of the exposed
portion of the latch
pin. Diameter should
not be less than
1.324 inches.
1-Latch PinMeasure1
Do a detailed inspec-
tion of the latch pin
for damage. It is not
necessary to remove
the latch pin for this
inspection.
1-Latch PinInspect
Do a Detailed Inspec-
tion to make sure
that the bolt is not
loose, broken or
missing.
1-BoltInspect2
Do a Detailed Inspec-
tion to make sure
that the nut is not
loose, broken or
missing.
1-NutInspect
FIGURE 1: DETAILED INSPECTION
(SHEET 2 OF 2)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 08, 2010
747-52A2294Revision 1 August 16, 2011
48 of 97
BOEING SERVICE BULLETIN 747-52A2294
ALERTALERT

### Page 49 (OCR)

BOEING SERVICE BULLETIN 747-52A2294
ALERT  ALERT
000000000  NOTE: NUMBERS ADJACENT  TO LATCH PIN FITTINGS
DENOTE LATCH POSITIONS
MAIN DECK
SIDE CARGO
DOOR
DOORWAY
000  LOWER SILL  9  10
8
FITTING
2,4,6,8, & 10
DOORWAY
LOWER
SILL
LATCH PIN
FITTING
• 1,3,5,7, & 9
LATCH PIN RETENTION BRACKET
NOT SHOWN
A-A  FITTING  1941740
FIGURE 2: TORQUE CHECK
(SHEET 1 OF 2)
Original Issue: July 08, 2010
Revision 1 August 16, 2011  Copyright © Unpublished Work - See page 1 for details.  BOEING PROPRIETARY -  747-52A2294  49 of 97

### Page 50

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for one latch pin fitting location.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
From bolt head. Op-
tional: Remove
sealant from the nut.
-BMS 5-95SealantRemove1
Apply 13 - 15 inch-
pounds of torque to
the bolt head. Option-
al: Apply 13 - 15
inch-pounds of
torque to the nut.
--BoltTorque2
FIGURE 2: TORQUE CHECK
(SHEET 2 OF 2)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 08, 2010
747-52A2294Revision 1 August 16, 2011
50 of 97
BOEING SERVICE BULLETIN 747-52A2294
ALERTALERT

### Page 51 (OCR)

BOEING SERVICE BULLETIN 747-52A2294
ALERT  ALERT
000000000  NOTE: NUMBERS ADJACENT  TO LATCH PIN FITTINGS
DENOTE LATCH POSITIONS
MAIN DECK
SIDE CARGO
0000  DOOR  DOORWAY
000  LOWER SILL  9  10
8
DOORWAY
LOWER
SILL
FITTING
2,4,6,8, & 10
в≤
FITTING
1,3,5,7, & 9
1941778
FIGURE 3: LATCH PIN POSITION CHECK
(SHEET 1 OF 3)
Original Issue: July 08, 2010
Revision 1 August 16, 2011  BOEING PROPRIETARY -  747-52A2294
Copyright © Unpublished Work - See page 1 for details.  51 of 97

### Page 52 (OCR)

BOEING SERVICE BULLETIN 747-52A2294
ALERT  ALERT
LATCH PIN
• FITTING
LATCH PIN
RETENTION
BOLT HOLE
A-A
LATCH PIN
RETENTION
BOLT HOLE  B-B
(IN FITTING)
RETENTION
BOLT HOLE
(IN LATCH PIN)
FIGURE 3: LATCH PIN POSITION CHECK
(SHEET 2 OF 3)
Original Issue: July 08, 2010
Revision 1 August 16, 2011  BOEING PROPRIETARY -  747-52A2294
Copyright © Unpublished Work - See page 1 for details.  52 of 97

### Page 53

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for one latch pin fitting location.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
(a)1-NutRemove1
(a)1-WasherRemove
(a)1-BoltRemove
If installed.--BracketRemove
Check if the latch pin
has migrated away
from the nominal in-
stalled position. (b)
1-Latch PinInspect2
(a) Unless the parts are found to be missing. If the retention bolt is fractured, use care to remove the sections
of the bolt from the latch pin fitting. If both ends of the bolt have been sheared, the shank of the bolt may
be trapped in the latch pin.
(b) If the retention bolt hole in the latch pin is not aligned with the retention bolt hole in the latch pin fitting,
consider the pin to have migrated. If the operator wishes to measure and record the distance (forward or
aft) that the latch pin has migrated, this is one method that can be used: 1. Look into the retention bolt
hole in the latch pin fitting. If the hole in the latch pin is not aligned with the hole in the fitting, make a mark
on the protruding end of the latch pin at the edge of the latch pin fitting lug. 2. Move the latch pin as nec-
essary to align the hole in the latch pin with the hole in the fitting, and make another mark on the protruding
end of the latch pin at the edge of the latch pin fitting lug. 3. Remove the latch pin and measure the distance
between the two marks. The distance measured is the distance the pin has migrated.
FIGURE 3: LATCH PIN POSITION CHECK
(SHEET 3 OF 3)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 08, 2010
747-52A2294Revision 1 August 16, 2011
53 of 97
BOEING SERVICE BULLETIN 747-52A2294
ALERTALERT

### Page 54 (OCR)

BOEING SERVICE BULLETIN 747-52A2294
ALERT  ALERT
000000000  NOTE: NUMBERS ADJACENT
TO LATCH PIN FITTINGS
DENOTE LATCH POSITIONS
MAIN DECK
SIDE CARGO
00  DOOR
000
DOORWAY
LOWER SILL
LATCH PIN
FITTING
LATCH PIN
FITTING
) BRACKET  (1) FILLET SEAL
A-A  LATCH PIN  TYPICAL AFFECTED LATCH PIN FITTING  1941914
FIGURE 4: PART REPLACEMENT AT LATCH PIN FITTING POSITIONS #1, #3, #7, #8, #9 AND #10
(SHEET 1 OF 3)
Original Issue: July 08, 2010
Revision 1 August 16, 2011  BOEING PROPRIETARY -  747-52A2294
Copyright © Unpublished Work - See page 1 for details.  54 of 97

### Page 55

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for one latch pin fitting location.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
If not previously re-
moved to check for
latch pin migration.
1-NutRemove1
If not previously re-
moved to check for
latch pin migration.
1-WasherRemove
If not previously re-
moved to check for
latch pin migration.
1-BoltRemove
If installed, and if not
previously removed
to check for latch pin
migration.
169B18044-2BRACKETRemove
-1-Latch PinRemove2
(a) (b)--Latch Pin FittingInspect3
Not shown (a)--Door Latch CamsInspect
Remove old sealant
from the bore.
--Latch Pin FittingClean
To the outer diame-
ter of the pin and to
the bore of the fit-
ting.
-BMS 5-95SealantApply4
Install the pin while
the sealant is still
wet. Line up the re-
tention bolt holes in
the latch pin with the
holes in the latch pin
fitting.
169B15457-7PINInstall (New)
Between the latch
pin fitting and the
flanges of the brack-
et.
-BMS 5-95SealantApply5
(e)169B18044-2BRACKETInstall (New)
FIGURE 4: PART REPLACEMENT AT LATCH PIN FITTING POSITIONS #1, #3, #7, #8, #9 AND #10
(SHEET 2 OF 3)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 08, 2010
747-52A2294Revision 1 August 16, 2011
55 of 97
BOEING SERVICE BULLETIN 747-52A2294
ALERTALERT

### Page 56

MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
Wet with BMS 5-95
sealant.
1BACB30LM3-27BOLTInstall (New)6
Install 1 or 2 wash-
ers, as necessary.
2NAS1149E0332PWASHER, PLAINInstall (New)
Apply 33 - 37 inch-
pounds of torque to
the nut (optional: ap-
ply torque to the bolt
head.)
1BACN10JC3CDNUTInstall (New)
(c) (d)-BMS 5-95SealantApply7
(a) Do a Detailed Inspection of the affected fitting and the corresponding door latch cams for evidence of
impact damage. If damage is found, contact Boeing for repair instructions and do the repair. Restore
damaged finishes as necessary.
(b) Do a Detailed Inspection of the retention bolt holes in the fitting for cracks or other damage. If damage is
found, contact Boeing for repair instructions and do the repair.
(c) Encapsulate bolt head, nut, washer, and bolt threads. Fillet seal the periphery of the bolt inside the pin.
(d) Apply a fillet seal of BMS 5-95 sealant all around the latch pin at the space between the latch pin and the
fitting. Use care to keep the tapered end of the pin, which will be engaged by the door latch cams, free
of sealant. It is not necessary to fillet seal the end of the fitting covered by the bracket.
(e) It is acceptable to reinstall the bracket that was previously removed, if it is in serviceable condition.
FIGURE 4: PART REPLACEMENT AT LATCH PIN FITTING POSITIONS #1, #3, #7, #8, #9 AND #10
(SHEET 3 OF 3)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 08, 2010
747-52A2294Revision 1 August 16, 2011
56 of 97
BOEING SERVICE BULLETIN 747-52A2294
ALERTALERT

### Page 57 (OCR)

BOEING SERVICE BULLETIN 747-52A2294
ALERT  ALERT
This Figure applies only to: Group 1-2, Configuration 2.
000000000  NOTE: NUMBERS ADJACENT
TO LATCH PIN FITTINGS
DENOTE LATCH POSITIONS
MAIN DECK
SIDE CARGO
DOOR
000
DOORWAY
LOWER SILL
LATCH PIN
FITTING
LATCH PIN
FITTING
FILLET SEAL  5) BRACKET
(2)
LATCH PIN  FWD  1942190
A-A
FIGURE 5: PART REPLACEMENT AT LATCH PIN FITTING POSITION #2
(SHEET 1 OF 3)
Original Issue: July 08, 2010
Revision 1 August 16, 2011  747-52A2294
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.  57 of 97

### Page 58

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for one latch pin fitting location.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
If not previously re-
moved to check for
latch pin migration.
1-NutRemove1
If not previously re-
moved to check for
latch pin migration.
1-WasherRemove
If not previously re-
moved to check for
latch pin migration.
1-BoltRemove
If installed, and if not
previously removed
to check for latch pin
migration.
169B18044-2BRACKETRemove
-1-Latch PinRemove2
(a) (b)--Latch Pin FittingInspect3
Not shown (a)--Door Latch CamsInspect
Remove old sealant
from the bore.
--Latch Pin FittingClean
To the outer diame-
ter of the pin and to
the bore of the fit-
ting.
-BMS 5-95SealantApply4
Install the pin while
the sealant is still
wet. Line up the re-
tention bolt holes in
the latch pin with the
holes in the latch pin
fitting.
169B15457-7Latch PinInstall (New)
between the latch
pin fitting and the
flanges of the brack-
et.
-BMS 5-95SealantApply5
(e)169B18044-2BRACKETInstall (New)
FIGURE 5: PART REPLACEMENT AT LATCH PIN FITTING POSITION #2
(SHEET 2 OF 3)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 08, 2010
747-52A2294Revision 1 August 16, 2011
58 of 97
BOEING SERVICE BULLETIN 747-52A2294
ALERTALERT

### Page 59

MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
wet with BMS 5-95
sealant.
1BACB30LM3-27BOLTInstall (New)6
Install 1 or 2 wash-
ers, as necessary.
2NAS1149E0332PWASHER, PLAINInstall (New)
Apply 33 - 37 inch-
pounds of torque to
the nut (optional: ap-
ply torque to the bolt
head.)
1BACN10JC3CDNUTInstall (New)
(c) (d)-BMS 5-95SealantApply7
(a) Do a Detailed Inspection of the affected fitting and the corresponding door latch cams for evidence of
impact damage. If damage is found, contact Boeing for repair instructions and do the repair. Restore
damaged finishes as necessary.
(b) Do a Detailed Inspection of the retention bolt holes in the fitting for cracks or other damage. If damage is
found, contact Boeing for repair instructions and do the repair.
(c) Encapsulate bolt head, nut, washer, and bolt threads. Fillet seal the periphery of the bolt inside the pin.
(d) Apply a fillet seal of BMS 5-95 sealant all around the latch pin at the space between the latch pin and the
fitting. Use care to keep the tapered end of the pin, which will be engaged by the door latch cams, free
of sealant. It is not necessary to fillet seal the end of the fitting covered by the bracket.
(e) It is acceptable to reinstall the bracket that was previously removed, if it is in serviceable condition.
FIGURE 5: PART REPLACEMENT AT LATCH PIN FITTING POSITION #2
(SHEET 3 OF 3)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 08, 2010
747-52A2294Revision 1 August 16, 2011
59 of 97
BOEING SERVICE BULLETIN 747-52A2294
ALERTALERT

### Page 60 (OCR)

BOEING SERVICE BULLETIN 747-52A2294
ALERT  ALERT
• This Figure applies only to: Group 1-2, Configuration 1; Group 3.
000000000  NOTE: NUMBERS ADJACENT  TO LATCH PIN FITTINGS
DENOTE LATCH POSITIONS
MAIN DECK
SIDE CARGO
DOOR
000
~
DOORWAY
LOWER SILL
1X6 SWITCH STRIKER
7 8
LATCH PIN  15 BRACKET
FITTING
5) BRACKET
SWITCH
FILLET SEAL  STRIKER
LATCH PIN  WD  A-A  FITTING  LATCH PIN  1942193
FIGURE 6: PART REPLACEMENT AT LATCH PIN FITTING POSITION #2
(SHEET 1 OF 3)
Original Issue: July 08, 2010
Revision 1 August 16, 2011  BOEING PROPRIETARY -  747-52A2294
Copyright © Unpublished Work - See page 1 for details.  60 of 97

The text continues at https://openairdocs.org/service-documents/boeing/747-52a2294/file/9889346c9c47.md?from=61

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
