# Boeing Alert Service Bulletin 747-53A2887: No revision named, from page 25

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2016-8181; AD 2016-26-07 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Alert Service Bulletin 747-53A2887](https://openairdocs.org/service-documents/boeing/747-53a2887.md)
- Title as filed: SB BOEING-747-53A2887-00
- Pages: 85
- PDF: https://openairdocs.org/files/sha256/1f/0c/1f0cd8aee6e2a5bba22b89726972f9575ba3b698d482164d7c770238de91aea6
- Page: https://openairdocs.org/service-documents/boeing/747-53a2887/file/1f0cd8aee6e2

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 25

Group 2-3, 5-6:
Table 2 - Detailed Inspection
Repeat Interval
(Not to Exceed)
Compliance time (Whichever is later)ActionCondition
-Within 3,000 flight
cycles after the
original issue date
of this service bul-
letin.
Before 25,000 total
flight cycles.
Do PART 2: NOSE
WHEEL WELL
BODY STRUC-
TURE DETAILED
INSPECTION for
any crack.
All airplanes
-Before further flight.CONDITION 1
(ACTION 1): Do
PART 4: SEC-
ONDARY INSPEC-
TION AND RE-
PAIR.
CONDITION 1:
ANY CRACK
FOUND during
PART 2.
3,000 flight cycles.-CONDITION 1
(ACTION 2): Re-
peat PART 2:
NOSE WHEEL
WELL BODY
STRUCTURE DE-
TAILED INSPEC-
TION for any crack
at unrepaired areas
only.
3,000 flight cycles.-Repeat PART 2:
NOSE WHEEL
WELL BODY
STRUCTURE DE-
TAILED INSPEC-
TION for any crack
at unrepaired areas
only.
CONDITION 2: NO
CRACK FOUND
during PART 2.
F. Approval
This service bulletin was examined by the Federal Aviation Administration (FAA). The changes specified
in this service bulletin comply with the applicable regulations and are FAA approved, as well as European
Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved
airplanes listed in the service bulletin effectivity. This service bulletin and its approval were based on
the airplane in its original Boeing delivery configuration or as modified by other approved Boeing
changes.
If an airplane has a non-Boeing modification or repair that affects a component or system also affected
by this service bulletin, the operator is responsible for obtaining appropriate regulatory agency approval
before incorporating this service bulletin.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: December 02, 2015
747-53A2887
25 of 85
BOEING SERVICE BULLETIN 747-53A2887
ALERTALERT

### Page 26

G. Manpower
The following breakdown of manpower requirements is suggested as a guide to assist operators in
planning and accomplishing this modification. This estimate is for direct labor performed by an
experienced crew. It does not include setup, planning, familiarization, cure time, part fabrication, tool
acquisition, or lost time. Factor this estimate as necessary based on your own experience.
The manpower estimates are given for the following options:
• Inspection for each area
• Modification for each area
• Inspection for each inspection interval
• Modification for each airplane group
Group 1, 4:
Elapsed HoursTask HoursNumber of PersonsTask
4.008.002Open Access
70.00140.002Detailed Inspection
1.553.102Surface HFEC In-
spection
1.553.102Open Hole HFEC In-
spection
4.008.002Close Access
81.10162.20TOTAL FOR EACH AIRPLANE
Group 2-3, 5-6:
Elapsed HoursTask HoursNumber of PersonsTask
4.008.002Open Access
70.00140.002Detailed Inspection
4.008.002Close Access
78.00156.00TOTAL FOR EACH AIRPLANE
H. Weight and Balance Changes
None.
I. Electrical Load Data
Not affected.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: December 02, 2015
747-53A2887
26 of 85
BOEING SERVICE BULLETIN 747-53A2887
ALERTALERT

### Page 27

J. References
1. Existing Data:
a. Boeing Service Bulletin 747-53A2265, 747-53A2272, 747-53A2293, 747-53A2338,
747-53A2349, 747-53A2465, 747-53A2500, 747-53A2562, 747-53A2732, 747-53A2753,
747-53A2808
b. Boeing Service Letter 747-SL-51-048
c. Boeing Service Related Problem (SRP) 747-SRP-53-0479
d. Federal Aviation Administration (FAA) Airworthiness Directive (AD) 2001-14-18, 90-06-14 R1
e. Service Bulletin Index D6-30300
f. Standard Overhaul Practices Manual (SOPM) 20-50-01, 20-50-19
g. 747 Non-Destructive Testing (NDT) Manual Part 6, Section 51-00-00, Part 6, Section 53-30-19
h. 747-100/200/300 Aircraft Maintenance Manual (AMM) 25-00-00
i. 747-100/200/300 Structural Repair Manual (SRM) 51-30-02
j. 747-400 Aircraft Maintenance Manual (AMM) 25-00-00
k. 747-SP Structural Repair Manual (SRM) 51-30-02
2. Data Supplied with this Service Bulletin:
None.
3. Installation Drawings Used in the Preparation of this Service Bulletin:
TitleDrawing Number
Frame Installation - Body Station 30065B01708
Frame Installation - Body Station 32065B01709
Side Panel Installation65B07942
The table above lists applicable drawings used to prepare this service bulletin. These drawings
are not necessary to make the specified changes, and are not supplied with this service bulletin.
The drawings may not be applicable to all airplane configurations or operators.
K. Publications Affected
1. Publications:
None.
2. Damage Tolerance Based Structural Inspections:
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: December 02, 2015
747-53A2887
27 of 85
BOEING SERVICE BULLETIN 747-53A2887
ALERTALERT

### Page 28

Boeing has evaluated the repairs and/or changes in this service bulletin for effects on Fatigue
Critical Structure (FCS) and for changes to Damage Tolerance Inspections (DTI) required in the
Maintenance Program. This service bulletin affects FCS but no new DTIs are necessary.
L. Interchangeability and Intermixability of Parts
None.
M. Software Accomplishment Summary
Not affected.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: December 02, 2015
747-53A2887
28 of 85
BOEING SERVICE BULLETIN 747-53A2887
ALERTALERT

### Page 29

2.    MATERIAL INFORMATION
A. Material - Price and Availability
None.
B. Industry Support Information
Boeing warranty remedies are not available for the inspection and/or repair procedures given in this
service bulletin.
C. Parts Necessary for Each Airplane
1. Kits/Parts
None.
2. Parts and Materials Supplied by the Operator
The following parts or materials are necessary to do the change in this service bulletin. Parts and
materials in the manuals given in Paragraph 1.J., References, can also be necessary. Examine
operator part and material supply to make sure all necessary parts and materials are available.
Group 1:
NotesNameQTYPart Number /
Specification
Or BACR15BB10AD.Rivet12BACR15ET9D
Or BACR15ET9D.Rivet12BACR15BB10AD
Group 4:
NotesNameQTYPart Number /
Specification
Or BACB30MY6K6Y.Bolt12BACB30MY6K6X
Or BACB30MY6K6X.Bolt12BACB30MY6K6Y
To be installed with bolt
BACB30MY6K6X.
Collar12BACC30M6
To be installed with bolt
BACB30MY6K6Y.
Collar12BACC30AC6
3. Parts Modified and Reidentified
None.
4. Parts Removed and Not Replaced
None.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: December 02, 2015
747-53A2887
29 of 85
BOEING SERVICE BULLETIN 747-53A2887
ALERTALERT

### Page 30

D. Parts Necessary to Change Spares
None.
E. Special Tooling - Price and Availability
None.
F. Special Tooling Necessary to do this Service Bulletin
No special tools or equipment are necessary to do the change in this service bulletin. But maintenance
and overhaul tools in the manuals given in Paragraph 1.J., References, can be necessary. Examine
operator tool supply to make sure all necessary tools are available.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: December 02, 2015
747-53A2887
30 of 85
BOEING SERVICE BULLETIN 747-53A2887
ALERTALERT

### Page 31

3.    ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL INFORMATION
CAUTION: KEEP THE WORK AREA, WIRES AND ELECTRICAL BUNDLES CLEAN OF METAL
PARTICLES OR CONTAMINATION WHEN YOU USE TOOLS. UNWANTED MATERIAL,
METAL PARTICLES OR CONTAMINATION CAUGHT IN WIRE BUNDLES CAN CAUSE
DAMAGE TO THE BUNDLES. DAMAGED WIRE BUNDLES CAN CAUSE SPARKS OR
OTHER ELECTRICAL DAMAGE.
NOTE: 1. Manual titles are referred to by acronyms. Refer to Paragraph 1.J., References, for
definition of the acronyms.
2. Obey all of the warnings and cautions given in the specified manual sections.
3. Unless shown differently, these dimensions and tolerances are used:
– Linear dimensions are in inches
– Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus
or minus 0.03 inch
– Tolerance on rivet and bolt edge margin is plus or minus 0.05 inch
– Angular tolerance is plus or minus 2 degrees
– Hole dimensions for standard solid rivets and fasteners are in Structural Repair
Manual (SRM) Chapter 51
– Torque Values:
— Values for structural fasteners are given in 747 Structural Repair Manual,
Chapter 51.
— Values for airframe maintenance tasks are included in Chapter 20 of 747
Aircraft Maintenance Manual (AMM).
— Values for electrical maintenance tasks are included in Chapter 20 of
Standard Wiring Practices Manual (SWPM).
— Values for engine maintenance tasks are included in Chapter 70 of 747
Aircraft Maintenance Manual (AMM).
— Non-standard torque values for maintenance tasks are included in the
applicable installation step.
4. Use the approved fastener, process and material substitutions in accordance with
SRM Chapter 51.
5. If the length of any fastener specified in this service bulletin does not meet installation
standards given in SRM Chapter 51, then a fastener of the same specification, or
an approved substitute, with a length which meets the installation standards given
in SRM Chapter 51 may be used. In addition, washers may be installed for fastener
grip length in accordance with SRM Chapter 51. Refer to SOPM 20-50-01 for alternate
full threaded fasteners (screws) needed for installation in this service bulletin.
6. A Detailed Inspection is defined as: An intensive examination of a specific item,
installation, or assembly to detect damage, failure, or irregularity. Available lighting
is normally supplemented with a direct source of good lighting at an intensity deemed
appropriate. Inspection aids such as mirrors, magnifying lenses, etc. may be
necessary. Surface cleaning and elaborate procedures may be required.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: December 02, 2015
747-53A2887
31 of 85
BOEING SERVICE BULLETIN 747-53A2887
ALERTALERT

### Page 32

7. These work instructions refer to procedures included in other Boeing documents.
When the words "refer to" are used and the operator has an accepted alternative
procedure, the accepted alternative procedure can be used. When the words "in
accordance with" are included in the instruction, the procedure in the Boeing document
must be used.
8. Boeing Service Letter 747-SL-51-048, Damage Reporting and Repair Plan/Design
Guidelines, is an acceptable procedure to request information from Boeing for
additional structural repair instructions. The Service Letter describes what information
must be provided to Boeing before a structural repair can be provided.
9. Refer to Appendix A and B for logic diagrams. Logic diagrams are provided as an
aid only. Information contained in Paragraph 1.E., Compliance is the primary source
for compliance times. Information in Paragraph 3.B., Work Instructions is the primary
source for tasks required for compliance.
10. The instructions in Paragraph 3.B., Work Instructions and the figures can include
operation of tools or test equipment. Boeing Engineering Tool Drawings, the Illustrated
Tool and Equipment Manual, and the Special Tool and Ground Handling Drawing
Index contain data on versions of the tools or test equipment that you can use. It is
permitted to use replaced tools. It is not permitted to use superseded tools.
11. If it is necessary to remove more parts for access, you can remove those parts. If
you can get access without removing identified parts, it is not necessary to remove
all of the identified parts. Jacking and shoring limitations must be observed.
12. Where the work instructions include installation of a kept part, a new or serviceable
part with the same part number can be installed as an alternative to the kept part.
13. Use of colors in Figures is based on guidance from the ATA e-Business Program
(ATA) iSpec 2200.
14. When more than one OPTION is given for a CONDITION, do only one of the OPTION
numbers. When more than one ACTION is given for a CONDITION number or an
OPTION number, do all of the ACTION numbers for that CONDITION number or
OPTION number.
15. The compliance times for the actions in Paragraph 3.B., WORK INSTRUCTIONS
are in Paragraph 1.E., Compliance.
16. Some steps in the Work Instructions are labeled as Required for Compliance (RC).
If this service bulletin is mandated by an Airworthiness Directive (AD), then the steps
labeled as RC, including sub-steps under an RC step and any figures identified in
an RC step, must be done to comply with the AD. An Alternative Method of
Compliance (AMOC) is required for any deviations to RC steps, including sub-steps
and identified figures. Steps not labeled as RC may be deviated from using accepted
methods in accordance with the operator's maintenance or inspection program without
obtaining approval of an AMOC. This is provided that the RC steps, including
sub-steps and identified figures, can still be done as specified, and the airplane can
be put back in an airworthy condition.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: December 02, 2015
747-53A2887
32 of 85
BOEING SERVICE BULLETIN 747-53A2887
ALERTALERT

### Page 33

B. WORK INSTRUCTIONS
1. Get access to nose wheel well top and side wall panels. Remove and keep insulation blankets.
Refer to 747-100/200/300 AMM 25-00-00, or 747-400 AMM 25-00-00 as accepted procedures.
2. Group 1, 4:
RC- Do PART 1: MODIFICATION.
3. RC- Do PART 2: NOSE WHEEL WELL BODY STRUCTURE DETAILED INSPECTION for any
crack.
a. CONDITION 1: ANY CRACK FOUND during PART 2.
(1) CONDITION 1 (ACTION 1): Do PART 4: SECONDARY INSPECTION AND REPAIR.
(2) CONDITION 1 (ACTION 2): Repeat PART 2: NOSE WHEEL WELL BODY STRUCTURE
DETAILED INSPECTION for any crack at unrepaired areas only.
b. CONDITION 2: NO CRACK FOUND during PART 2.
(1) Repeat PART 2: NOSE WHEEL WELL BODY STRUCTURE DETAILED INSPECTION
for any crack at unrepaired locations only.
4. Group 1, 4:
RC- Do PART 3: STA 280-320 VERTICAL BEAM OUTER CHORD AND WEB SURFACE OR
OPEN HOLE HIGH FREQUENCY EDDY CURRENT (HFEC) INSPECTION for any crack.
a. CONDITION 3: SURFACE HIGH FREQUENCY EDDY CURRENT (HFEC) INSPECTION
DONE. ANY CRACK FOUND during PART 3.
(1) CONDITION 3 (ACTION 1): Do PART 4: SECONDARY INSPECTION AND REPAIR.
(2) CONDITION 3 (ACTION 2): Repeat PART 3: STA 280-320 VERTICAL BEAM OUTER
CHORD AND WEB SURFACE OR OPEN HOLE HIGH FREQUENCY EDDY CURRENT
(HFEC) INSPECTION for any crack at unrepaired areas only.
b. CONDITION 4: SURFACE HIGH FREQUENCY EDDY CURRENT (HFEC) INSPECTION
DONE. NO CRACK FOUND during PART 3.
(1) Repeat PART 3: STA 280-320 VERTICAL BEAM OUTER CHORD AND WEB SURFACE
OR OPEN HOLE HIGH FREQUENCY EDDY CURRENT (HFEC) INSPECTION for any
crack at unrepaired areas only.
c. CONDITION 5: OPEN HOLE HIGH FREQUENCY EDDY CURRENT (HFEC) INSPECTION
DONE. ANY CRACK FOUND during PART 3.
(1) CONDITION 5 (ACTION 1): Do PART 4: SECONDARY INSPECTION AND REPAIR.
(2) CONDITION 5 (ACTION 2): Repeat PART 3: STA 280-320 VERTICAL BEAM OUTER
CHORD AND WEB SURFACE OR OPEN HOLE HIGH FREQUENCY EDDY CURRENT
(HFEC) INSPECTION for any crack at unrepaired areas only.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: December 02, 2015
747-53A2887
33 of 85
BOEING SERVICE BULLETIN 747-53A2887
ALERTALERT

### Page 34

d. CONDITION 6: OPEN HOLE HIGH FREQUENCY EDDY CURRENT (HFEC) INSPECTION
DONE. NO CRACK FOUND during PART 3.
(1) Group 1:
CONDITION 6 (ACTION 1): Install new fasteners in accordance with FIGURE 9 and
FIGURE 10.
(2) Group 4:
CONDITION 6 (ACTION 1): Install new fasteners in accordance with FIGURE 11 and
FIGURE 12.
(3) CONDITION 6 (ACTION 2): Repeat PART 3: STA 280-320 VERTICAL BEAM OUTER
CHORD AND WEB SURFACE OR OPEN HOLE HIGH FREQUENCY EDDY CURRENT
(HFEC) INSPECTION for any crack at unrepaired areas only.
5. Install kept insulation blankets. Refer to 747-100/200/300 AMM 25-00-00, or 747-400 AMM 25-00-00
as accepted procedures.
6. Put the airplane back to serviceable condition.
Group 1, 4:
PART 1: MODIFICATION
1. Do the modification in accordance with service bulletin (SB) 747-53A2293 for areas 1, 3 and 4 in
accordance with the time given in Paragraph 1.E., Compliance of this Service Bulletin. If the
modification work was previously done in accordance with SB 747-53A2293, then there is no
further modification work required.
NOTE: In SB 747-53A2293, the Area 4 modification requires the same access as the Area 3
modification.
PART 2: NOSE WHEEL WELL BODY STRUCTURE DETAILED INSPECTION
1. Group 1-2, Configuration 1; Group 3, 5:
Do a detailed inspection of the left side nose wheel well body structure for any crack in accordance
with FIGURE 1.
2. Group 1-2, Configuration 1; Group 3, 5:
Do a detailed inspection of the right side nose wheel well body structure for any crack in accordance
with FIGURE 2.
3. Group 1-2, Configuration 2; Group 4, 6:
Do a detailed inspection of the left side nose wheel well body structure for any crack in accordance
with FIGURE 3.
4. Group 1-2, Configuration 2; Group 4, 6:
Do a detailed inspection of the right side nose wheel well body structure for any crack in accordance
with FIGURE 4.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: December 02, 2015
747-53A2887
34 of 85
BOEING SERVICE BULLETIN 747-53A2887
ALERTALERT

### Page 35

Group 1, 4:
PART 3: STA 280-320 VERTICAL BEAM OUTER CHORD AND WEB SURFACE OR OPEN HOLE
HIGH FREQUENCY EDDY CURRENT (HFEC) INSPECTION
1. Do one of the following options:
a. OPTION 1:
(1) ACTION 1: Do a Surface HFEC Inspection of the left side STA 280-320 vertical beam
outer chord and web for any crack in accordance with FIGURE 5.
(2) ACTION 2: Do a Surface HFEC Inspection of the right side STA 280-320 vertical beam
outer chord and web for any crack in accordance with FIGURE 6.
b. OPTION 2:
(1) ACTION 1: Do an Open Hole HFEC Inspection of the left side STA 280-320 vertical beam
outer chord and web for any crack in accordance with FIGURE 7.
(2) ACTION 2: Do an Open Hole HFEC Inspection of the right side STA 280-320 vertical
beam outer chord and web for any crack in accordance with FIGURE 8.
PART 4: SECONDARY INSPECTION AND REPAIR
1. Do a detailed inspection for any crack within 20 inches of the original crack, to determine the full
extent of the damage.
2. Contact The Boeing Company for repair instructions and do the repair.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: December 02, 2015
747-53A2887
35 of 85
BOEING SERVICE BULLETIN 747-53A2887
ALERTALERT

### Page 36 (OCR)

BOEING SERVICE BULLETIN 747-53A2887
ALERT  ALERT
This Figure applies only to: Group 1-2, Configuration 1; Group 3, 5.
STA
260
STA
260  / STA
CANTED STA  1280
340  /STA
300
STA
RBL 22  340
RBL 10
LBL 10 -
LBL 22 ~
2454876
FIGURE 1: LEFT SIDE NOSE WHEEL WELL BODY STRUCTURE - DETAILED INSPECTION
(SHEET 1 OF 7)
Original Issue: December 02, 2015
Export Controlled ECCN: 9E991 - BOEING  747-53A2887
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  36 of 85

### Page 37 (OCR)

BOEING SERVICE BULLETIN 747-53A2887
ALERT  ALERT
STA
280.
300
FLOORBEAM
TOP PANEL WEB
FORE AFT
STIFFENER
FORE AFT
STIFFENER
- BL
22
FORE AFT  STIFFENER (1  INTERCOSTAL
TYPICAL
CRACK
LOCATION  1 CLIP
POTENTIAL CRACK  TYPICAL STA 280-STA 300.  LBL 10 AND 22
LOCATION IN FORE AFT
STIFFENER
• INTERCOSTAL
BL
10
22
TYPICAL
U TOP PANEL  2454879
WEB
FIGURE 1: LEFT SIDE NOSE WHEEL WELL BODY STRUCTURE - DETAILED INSPECTION
(SHEET 2 OF 7)
Original Issue: December 02, 2015
Export Controlled ECCN: 9E991 - BOEING  747-53A2887
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  37 of 85

### Page 38 (OCR)

BOEING SERVICE BULLETIN 747-53A2887
ALERT  ALERT
® CHORD
1 SIDE WALL
VERTICAL  PANEL WEB
BEAM
VERTICAL
BEAM CLIP
TYPICAL CRACKS
IN VERTICAL
BEAM WEB
TYPICAL
INSULATION
BLANKET
STANDOFF/TOOL
HOLE LOCATION
2) HORIZONTAL
STIFFENER
VERTICAL (
BEAM CLIP
CHORD 1  STATIONS 260 THROUGH 320  (TYPICAL)
D
2454881
FIGURE 1: LEFT SIDE NOSE WHEEL WELL BODY STRUCTURE - DETAILED INSPECTION
(SHEET 3 OF 7)
Original Issue: December 02, 2015
Export Controlled ECCN: 9E991 - BOEING  747-53A2887
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  38 of 85

### Page 39 (OCR)

BOEING SERVICE BULLETIN 747-53A2887
ALERT  ALERT
MAIN DECK FLOOR BEAM
(AT STA 280, 300 AND 320 ONLY
VERTICAL BEAM 2
S-40L
S-41L
INBD
TYPICAL STATIONS 260 TO 320
A-A
FIGURE 1: LEFT SIDE NOSE WHEEL WELL BODY STRUCTURE - DETAILED INSPECTION
(SHEET 4 OF 7)
Original Issue: December 02, 2015
PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  747-53A2887
Work - See page 1 for details.  39 of 85

### Page 40 (OCR)

BOEING SERVICE BULLETIN 747-53A2887
ALERT  ALERT
STA
280
300
320
12.0
12.0
3) LOWER CHORI  FLOOR BEAN
® STRAP
STA
280
300
320
2) BEAM OUTER  VERTICAL
CHORD
TYPICAL
VERTICAL
BEAM
TYPICAL
CRACK
VERTICAL  BEAM WEB  ₴
VERTICAL BEAM (2
INNER CHORD
LOOF (3  FAM
LOWER CHORD 3  FLOOR BEAM  2454887
FIGURE 1: LEFT SIDE NOSE WHEEL WELL BODY STRUCTURE - DETAILED INSPECTION
(SHEET 5 OF 7)
Original Issue: December 02, 2015
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  40 of 85

### Page 41

The step numbers shown below agree with the numbers shown in the circle symbols in the figure.
More DataQtyIdentificationNameTaskStep
(a)--Fore Aft StiffenersInspect1
(b)--ClipsInspect
(c)--IntercostalInspect
(d)--Floor BeamInspect
(e)--Top Panel WebInspect
(f)--Vertical BeamInspect2
(f)--Vertical Beam WebInspect
(f)--Vertical Beam ChordInspect
(g)--Vertical Beam ClipsInspect
(h)--Horizontal StiffenersInspect
(i)--Main Deck Floor
Beams
Inspect3
(j)--Floor Beam Lower
Chords
Inspect
(k)--StrapsInspect
(a) Do a detailed inspection of the fore aft stiffeners, between Body Station (STA) 280 and STA 300, Left
Buttock Line (LBL) 10 and LBL 22, common to the top panel. Inspect from the top side, around all fastener
heads and in the stiffeners fillet radius, common to the horizontal flange attached to the nose wheel well
top panel web.
(b) Do a detailed inspection of all attachments of the clips to the fore aft stiffeners.
(c) Do a detailed inspection of the intercostals in the area surrounding the connection to the clip and the fore
aft stiffeners.
(d) Do a detailed inspection of the main deck floor beams in the area surrounding the connection to the fore
aft stiffeners.
(e) Do a detailed inspection of the top panel web in the area surrounding the connection to the fore aft stiff-
eners.
(f) Do a detailed inspection of the full length of the vertical beams, vertical beam webs and vertical beam
chords. Inspect both the forward and aft side of the beams. Inspect the joints between the vertical beams
and the frames and between the vertical beams and the main deck floor beams.
(g) Do a detailed inspection of all attachments of the vertical beam clips to the vertical beams, from inside
the fuselage.
(h) Do a detailed inspection of the horizontal stiffeners in the area surrounding the connection to the vertical
beams.
(i) Do a detailed inspection of the main deck floor beams, 12 inches outboard of the vertical beam to 12
inches inboard of the vertical beam. Inspect both the forward and aft side of the beams.
FIGURE 1: LEFT SIDE NOSE WHEEL WELL BODY STRUCTURE - DETAILED INSPECTION
(SHEET 6 OF 7)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: December 02, 2015
747-53A2887
41 of 85
BOEING SERVICE BULLETIN 747-53A2887
ALERTALERT

### Page 42

More DataQtyIdentificationNameTaskStep
(j) Do a detailed inspection of the floor beam lower chords, 12 inches outboard of the vertical beam to 12
inches inboard of the vertical beam. Inspect both the forward and aft side of the chord.
(k) Do a detailed inspection of the floor beam lower chords in the area around the ends of the reinforcing
straps.
FIGURE 1: LEFT SIDE NOSE WHEEL WELL BODY STRUCTURE - DETAILED INSPECTION
(SHEET 7 OF 7)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: December 02, 2015
747-53A2887
42 of 85
BOEING SERVICE BULLETIN 747-53A2887
ALERTALERT

### Page 43 (OCR)

BOEING SERVICE BULLETIN 747-53A2887
ALERT  ALERT
This Figure applies only to: Group 1-2, Configuration 1; Group 3, 5.
STA
260
STA
260
STA  _ CANTED
340
280
STA
300
STA
340  32  - LBL 22
- LBL 10
-RBL 10
RBL 22
2455847
FIGURE 2: RIGHT SIDE NOSE WHEEL WELL BODY STRUCTURE - DETAILED INSPECTION
(SHEET 1 OF 7)
Original Issue: December 02, 2015
Export Controlled ECCN: 9E991 - BOEING  747-53A2887
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  43 of 85

### Page 44 (OCR)

BOEING SERVICE BULLETIN 747-53A2887
ALERT  ALERT
STA
280,
300
FLOORBEAM
TOP PANEL WEB
FORE AFT
STIFFENER
FORE AFT
STIFFENER
BL
22
FORE AFT
INTERCOSTAL  STIFFENER
TYPICAL
CRACK
BI  LOCATION
10
TYPICAL STA 280-STA 300,  POTENTIAL CRACK
RBL 10 AND 22  LOCATION IN
FORE AFT STIFFENER
INTERCOSTAL
1 TOP PANEL  2455863
WEB
FIGURE 2: RIGHT SIDE NOSE WHEEL WELL BODY STRUCTURE - DETAILED INSPECTION
(SHEET 2 OF 7)
Original Issue: December 02, 2015
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.

### Page 45 (OCR)

BOEING SERVICE BULLETIN 747-53A2887
ALERT  ALERT
CHORD
SIDE WALL
PANEL WEB
VERTICAL
BEAM
2) VERTICAL
BEAM CLIP
TYPICAL CRACKS
IN VERTICAL
BEAM WEB
TYPICAL
INSULATION
BLANKET
STANDOFF/TOOL
HOLE LOCATION
HORIZONTAL
STIFFENER
2) VERTICAL
BEAM CLIF
STATIONS 260 THROUGH 320  CHORD
(TYPICAL
FIGURE 2: RIGHT SIDE NOSE WHEEL WELL BODY STRUCTURE - DETAILED INSPECTION
(SHEET 3 OF 7)
Original Issue: December 02, 2015
Export Controlled ECCN: 9E991 - BOEING  747-53A2887
PROPRIETARY - Copyright © Unpublished  Work - See page 1 for details.  45 of 85

### Page 46 (OCR)

BOEING SERVICE BULLETIN 747-53A2887
ALERT  ALERT
MAIN DECK FLOOR BEAM
(AT STA 230, 300 AND 320 ONLY)
2) VERTICAL BEAM
S-39R
S-40R
S-41R
INBD
TYPICAL STATIONS 260 TO 320  2455880
A-A
FIGURE 2: RIGHT SIDE NOSE WHEEL WELL BODY STRUCTURE - DETAILED INSPECTION
(SHEET 4 OF 7)
Original Issue: December 02, 2015
Export Controlled ECCN: 9E991 - BOEING  747-53A2887
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  46 of 85

### Page 47 (OCR)

BOEING SERVICE BULLETIN 747-53A2887
ALERT  ALERT
STA
280
300
320
12.0
FLOOR BEAM
LOWER CHORD
STRAP
VERTICAL
BEAM OUTER 2
CHORD
TYPICAL  BEAM  VERTICAL
TYPICAL
CRACK
VERTICAL
BEAM WEB
2) VERTICAL BEA  INNER CHORI
3 BEAM  FLOOR
FLOOR BEAI  2455892
/LOWER CHOR
FIGURE 2: RIGHT SIDE NOSE WHEEL WELL BODY STRUCTURE - DETAILED INSPECTION
(SHEET 5 OF 7)
Original Issue: December 02, 2015
Export Controlled ECCN: 9E991 - BOEING  747-53A2887
PROPRIETARY - Copyright © Unpublished  Work - See page 1 for details.  47 of 85

### Page 48

The step numbers shown below agree with the numbers shown in the circle symbols in the figure.
More DataQtyIdentificationNameTaskStep
(a)--Fore Aft StiffenersInspect1
(b)--ClipsInspect
(c)--IntercostalInspect
(d)--Floor BeamInspect
(e)--Top Panel WebInspect
(f)--Vertical BeamInspect2
(f)--Vertical Beam WebInspect
(f)--Vertical Beam ChordInspect
(g)--Vertical Beam ClipsInspect
(h)--Horizontal StiffenersInspect
(i)--Main Deck Floor
Beams
Inspect3
(j)--Floor Beam Lower
Chords
Inspect
(k)--StrapsInspect
(a) Do a detailed inspection of the fore aft stiffeners, between Body Station (STA) 280 and STA 300, Right
Buttock Line (RBL) 10 and RBL 22, common to the top panel. Inspect from the top side, around all fastener
heads and in the stiffeners fillet radius, common to the horizontal flange attached to the nose wheel well
top panel web.
(b) Do a detailed inspection of all attachments of the clips to the fore aft stiffeners.
(c) Do a detailed inspection of the intercostals in the area surrounding the connection to the clip and the fore
aft stiffeners.
(d) Do a detailed inspection of the main deck floor beams in the area surrounding the connection to the fore
aft stiffeners.
(e) Do a detailed inspection of the top panel web in the area surrounding the connection to the fore aft stiff-
eners.
(f) Do a detailed inspection of the full length of the vertical beams, vertical beam webs and vertical beam
chords. Inspect both the forward and aft side of the beams. Inspect the joints between the vertical beams
and the frames and between the vertical beams and the main deck floor beams.
(g) Do a detailed inspection of all attachments of the vertical beam clips to the vertical beams, from inside
the fuselage.
(h) Do a detailed inspection of the horizontal stiffeners in the area surrounding the connection to the vertical
beams.
(i) Do a detailed inspection of the main deck floor beams, 12 inches outboard of the vertical beam to 12
inches inboard of the vertical beam. Inspect both the forward and aft side of the beams.
FIGURE 2: RIGHT SIDE NOSE WHEEL WELL BODY STRUCTURE - DETAILED INSPECTION
(SHEET 6 OF 7)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: December 02, 2015
747-53A2887
48 of 85
BOEING SERVICE BULLETIN 747-53A2887
ALERTALERT

### Page 49

More DataQtyIdentificationNameTaskStep
(j) Do a detailed inspection of the floor beam lower chords, 12 inches outboard of the vertical beam to 12
inches inboard of the vertical beam. Inspect both the forward and aft side of the chord.
(k) Do a detailed inspection of the floor beam lower chords in the area around the ends of the reinforcing
straps.
FIGURE 2: RIGHT SIDE NOSE WHEEL WELL BODY STRUCTURE - DETAILED INSPECTION
(SHEET 7 OF 7)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: December 02, 2015
747-53A2887
49 of 85
BOEING SERVICE BULLETIN 747-53A2887
ALERTALERT

### Page 50 (OCR)

BOEING SERVICE BULLETIN 747-53A2887
ALERT  ALERT
This Figure applies only to: Group 1-2, Configuration 2; Group 4, 6.
STA
260
STA
260  A STA
CANTED STA  1280
340  /STA
300
STA
RBL 22  340
RBL 10
LBL 10 -
LBL 22 ~
2454877
FIGURE 3: LEFT SIDE NOSE WHEEL WELL BODY STRUCTURE - DETAILED INSPECTION
(SHEET 1 OF 6)
Original Issue: December 02, 2015
Export Controlled ECCN: 9E991 - BOEING  747-53A2887
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  50 of 85

### Page 51 (OCR)

BOEING SERVICE BULLETIN 747-53A2887
ALERT  ALERT
STA
280
300
FLOORBEAM
Q
TOP PANEL WEB
FORE AFT
STIFFENER
FORE AFT
STIFFENER
- BL
22
FORE AFT  STIFFENER 1  INTERCOSTAL
TYPICAL
CRACK
LOCATION  1 CLIP
POTENTIAL CRAC  TYPICAL STA 280-STA 300.  LBL 10 AND 22
OCATION IN FOR
AFT STIFFENER
1 INTERCOSTAL
BL
10
22
TYPICAL
1 TOP PANEL  2454880
WEB
FIGURE 3: LEFT SIDE NOSE WHEEL WELL BODY STRUCTURE - DETAILED INSPECTION
(SHEET 2 OF 6)
Original Issue: December 02, 2015
Export Controlled ECCN: 9E991 - BOEING  747-53A2887
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  51 of 85

### Page 52 (OCR)

BOEING SERVICE BULLETIN 747-53A2887
ALERT  ALERT
® CHORD
1 SIDE WALL
VERTICAL  PANEL WEB
BEAM
VERTICAL
BEAM CLIP
TYPICAL CRACKS
IN VERTICAL
BEAM WEB
TYPICAL
INSULATION
BLANKET
STANDOFF/TOOL
HOLE LOCATION
2) HORIZONTAL
STIFFENER
VERTICAL 3
BEAM CLIP
CHORDE  STATIONS 260 THROUGH 320  (TYPICAL)
D
2454883
FIGURE 3: LEFT SIDE NOSE WHEEL WELL BODY STRUCTURE - DETAILED INSPECTION
(SHEET 3 OF 6)
Original Issue: December 02, 2015
Export Controlled ECCN: 9E991 - BOEING  747-53A2887
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  52 of 85

### Page 53 (OCR)

BOEING SERVICE BULLETIN 747-53A2887
ALERT  ALERT
MAIN DECK FLOOR BEAM
(AT STA 280, 300 AND 320 ONLY)
VERTICAL BEAM 2
S-40L
S-41L
INED
TYPICAL STATIONS 260 TO 320
A-A
FIGURE 3: LEFT SIDE NOSE WHEEL WELL BODY STRUCTURE - DETAILED INSPECTION
(SHEET 4 OF 6)
Original Issue: December 02, 2015
Export Controlled ECCN: 9E991 - BOEING  747-53A2887
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  53 of 85

### Page 54 (OCR)

BOEING SERVICE BULLETIN 747-53A2887
ALERT  ALERT
STA
280
300
320
12.0
12.0
3) LOWER CHORI  FLOOR BEAI
STA
280
300
320
VERTICAL
(2) BEAM OUTER
CHORD
TYPICAL
VERTICAL
BEAM
TYPICAL
CRACK
VERTICAL
BEAM WEB
VERTICAL BEAM (2
INNER CHORD
LOOF (3  FAM
LOWER CHORD 3  FLOOR BEAM  2454894
FIGURE 3: LEFT SIDE NOSE WHEEL WELL BODY STRUCTURE - DETAILED INSPECTION
(SHEET 5 OF 6)
Original Issue: December 02, 2015
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  54 of 85

### Page 55

The step numbers shown below agree with the numbers shown in the circle symbols in the figure.
More DataQtyIdentificationNameTaskStep
(a)--Fore Aft StiffenersInspect1
(b)--ClipsInspect
(c)--IntercostalInspect
(d)--Floor BeamInspect
(e)--Top Panel WebInspect
(f)--Vertical BeamInspect2
(f)--Vertical Beam WebInspect
(f)--Vertical Beam ChordInspect
(g)--Vertical Beam ClipsInspect
(h)--Horizontal StiffenersInspect
(i)--Main Deck Floor
Beams
Inspect3
(j)--Floor Beam Lower
Chords
Inspect
(a) Do a detailed inspection of the fore aft stiffeners, between Body Station (STA) 280 and STA 300, Left
Buttock Line (LBL) 10 and LBL 22, common to the top panel. Inspect from the top side, around all fastener
heads and in the stiffeners fillet radius, common to the horizontal flange attached to the nose wheel well
top panel web.
(b) Do a detailed inspection of all attachments of the clips to the fore aft stiffeners.
(c) Do a detailed inspection of the intercostals in the area surrounding the connection to the clip and the fore
aft stiffeners.
(d) Do a detailed inspection of the floor beams in the area surrounding the connection to the fore aft stiffeners.
(e) Do a detailed inspection of the top panel web in the area surrounding the connection to the fore aft stiff-
eners.
(f) Do a detailed inspection of the full length of the vertical beams, vertical beam webs and vertical beam
chords. Inspect both the forward and aft side of the beams. Inspect the joints between the vertical beams
and the frames and between the vertical beams and the floor beams.
(g) Do a detailed inspection of all attachments of the vertical beam clips to the vertical beams, from inside
the fuselage.
(h) Do a detailed inspection of the horizontal stiffeners in the area surrounding the connection to the vertical
beams.
(i) Do a detailed inspection of the main deck floor beams, 12 inches outboard of the vertical beam to 12
inches inboard of the vertical beam. Inspect both the forward and aft side of the beams.
(j) Do a detailed inspection of the floor beam lower chords, 12 inches outboard of the vertical beam to 12
inches inboard of the vertical beam. Inspect both the forward and aft side of the chord.
FIGURE 3: LEFT SIDE NOSE WHEEL WELL BODY STRUCTURE - DETAILED INSPECTION
(SHEET 6 OF 6)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: December 02, 2015
747-53A2887
55 of 85
BOEING SERVICE BULLETIN 747-53A2887
ALERTALERT

### Page 56 (OCR)

BOEING SERVICE BULLETIN 747-53A2887
ALERT  ALERT
This Figure applies only to: Group 1-2, Configuration 2; Group 4, 6.
STA
260
STA
260
CANTED
STA
340
STA
280
STA
300
STA  STA
340  320  - LBL 20
- LBL 10
- RBL 10
RBL 22
2456026
FIGURE 4: RIGHT SIDE NOSE WHEEL WELL BODY STRUCTURE - DETAILED INSPECTION
(SHEET 1 OF 6)
Original Issue: December 02, 2015
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  56 of 85

### Page 57 (OCR)

BOEING SERVICE BULLETIN 747-53A2887
ALERT  ALERT
FLOORBEAM
TOP PANEL WEB
FORE AFT
STIFFENER
FORE AFT
STIFFENER
BL
22
FORE AFT
INTERCOSTAL  STIFFENER
TYPICAL
CRACK
CLIP  LOCATION
BL
10
TYPICAL STA 280-STA 300,
RBL 10 AND 22  POTENTIAL CRACK
LOCATION IN FORE AFT
STIFFENER
INTERCOSTAL
*BL
TOP PANEL  10
WEB  22
TYPICAL
FIGURE 4: RIGHT SIDE NOSE WHEEL WELL BODY STRUCTURE - DETAILED INSPECTION
(SHEET 2 OF 6)
Original Issue: December 02, 2015
Export Controlled ECCN: 9E991 - BOEING  747-53A2887
PROPRIETARY - Copyright © Unpublished  Work - See page 1 for details.  57 of 85

### Page 58 (OCR)

BOEING SERVICE BULLETIN 747-53A2887
ALERT  ALERT
SIDE WALL  PANEL WEB  CHORD
VERTICAL
BEAM
2) VERTICAL
BEAM CLIP
TYPICAL CRACKS
•IN VERTICAL
BEAM WEB
TYPICAL
INSULATION
- BLANKET
STANDOFF/TOOL
HOLE LOCATION
HORIZONTAL
STIFFENER
2) VERTICAL
BEAM CLIP
STATIONS 260 THROUGH 320
(TYPICAL)  CHORD
2456061
FIGURE 4: RIGHT SIDE NOSE WHEEL WELL BODY STRUCTURE - DETAILED INSPECTION
(SHEET 3 OF 6)
Original Issue: December 02, 2015
Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright © Unpublished  747-53A2887
Work - See page 1 for details.  58 of 85

### Page 59 (OCR)

BOEING SERVICE BULLETIN 747-53A2887
ALERT  ALERT
MAIN DECK FLOOR BEAM
(AT STA 280, 300 AND 320 ONLY)
3 VERTICAL BEAM
S-39R
S-40R
S-41R
INBD
TYPICAL STATIONS 260 TO 320  2456067
A-A
FIGURE 4: RIGHT SIDE NOSE WHEEL WELL BODY STRUCTURE - DETAILED INSPECTION
(SHEET 4 OF 6)
Original Issue: December 02, 2015
Export Controlled ECCN: 9E991 - BOEING  747-53A2887
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  59 of 85

### Page 60 (OCR)

BOEING SERVICE BULLETIN 747-53A2887
ALERT  ALERT
12.0
FLOOR BEAM
LOWER CHORD
VERTICAL
BEAM OUTER (2)
CHORD
*YPICA  • VERTICAL  BEAM
TYPICAL
CRACK
VERTICAL
BEAM WEB
-E WERE CAPE
3) BEA  FLOO
FLOOR BEAI  2456071
A LOWER CHOR
FIGURE 4: RIGHT SIDE NOSE WHEEL WELL BODY STRUCTURE - DETAILED INSPECTION
(SHEET 5 OF 6)
Original Issue: December 02, 2015
Export Controlled ECCN: 9E991 - BOEING  747-53A2887
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  60 of 85

### Page 61

The step numbers shown below agree with the numbers shown in the circle symbols in the figure.
More DataQtyIdentificationNameTaskStep
(a)--Fore Aft StiffenersInspect1
(b)--ClipsInspect
(c)--IntercostalInspect
(d)--Floor BeamInspect
(e)--Top Panel WebInspect
(f)--Vertical BeamInspect2
(f)--Vertical Beam WebInspect
(f)--Vertical Beam ChordInspect
(g)--Vertical Beam ClipsInspect
(h)--Horizontal StiffenersInspect
(i)--Main Deck Floor
Beams
Inspect3
(j)--Floor Beam Lower
Chords
Inspect
(a) Do a detailed inspection of the fore aft stiffeners, between Body Station (STA) 280 and STA 300, Right
Buttock Line (RBL) 10 and RBL 22, common to the top panel. Inspect from the top side, around all fastener
heads and in the stiffeners fillet radius, common to the horizontal flange attached to the nose wheel well
top panel web.
(b) Do a detailed inspection of all attachments of the clips to the fore aft stiffeners.
(c) Do a detailed inspection of the intercostals in the area surrounding the connection to the clip and the fore
aft stiffeners.
(d) Do a detailed inspection of the floor beams in the area surrounding the connection to the fore aft stiffeners.
(e) Do a detailed inspection of the top panel web in the area surrounding the connection to the fore aft stiff-
eners.
(f) Do a detailed inspection of the full length of the vertical beams, vertical beam webs and vertical beam
chords. Inspect both the forward and aft side of the beams. Inspect the joints between the vertical beams
and the frames and between the vertical beams and the floor beams.
(g) Do a detailed inspection of all attachments of the vertical beam clips to the vertical beams, from inside
the fuselage.
(h) Do a detailed inspection of the horizontal stiffeners in the area surrounding the connection to the vertical
beams.
(i) Do a detailed inspection of the main deck floor beams, 12 inches outboard of the vertical beam to 12
inches inboard of the vertical beam. Inspect both the forward and aft side of the beams.
(j) Do a detailed inspection of the floor beam lower chords, 12 inches outboard of the vertical beam to 12
inches inboard of the vertical beam. Inspect both the forward and aft side of the chord.
FIGURE 4: RIGHT SIDE NOSE WHEEL WELL BODY STRUCTURE - DETAILED INSPECTION
(SHEET 6 OF 6)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: December 02, 2015
747-53A2887
61 of 85
BOEING SERVICE BULLETIN 747-53A2887
ALERTALERT

### Page 62 (OCR)

BOEING SERVICE BULLETIN 747-53A2887
ALERT  ALERT
This Figure applies only to: Group 1, 4.
STA
260
STA  *STA
CANTED STA  260  ¡ 280
340
RBL 22.  STA  340
RBL 10 -
LBL 10 -
LBL 22 ~
2454901
FIGURE 5: LEFT SIDE STA 280-320 VERTICAL BEAM OUTER CHORD AND WEB - SURFACE HIGH
FREQUENCY EDDY CURRENT (HFEC) INSPECTION
(SHEET 1 OF 3)
Original Issue: December 02, 2015
PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  747-53A2887
Work - See page 1 for details.  62 of 85

### Page 63 (OCR)

BOEING SERVICE BULLETIN 747-53A2887C
ALERT  ALERT
VERTICAL
BEAM
WEB
VERTICAL
BEAM OUTER
CHORD
FLOOR
BEAM
TYPICAL
CRACK
INSPECTION AREA
FLOOR
BEAM
VERTICAL
BEAM OUTER
CHORD
VERTICAL
BEAM WEB  A-A
FIGURE 5: LEFT SIDE STA 280-320 VERTICAL BEAM OUTER CHORD AND WEB - SURFACE HIGH
FREQUENCY EDDY CURRENT (HFEC) INSPECTION
(SHEET 2 OF 3)
Original Issue: December 02, 2015
Export Controlled ECCN: 9E991 - BOEING  747-53A2887
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  63 of 85

### Page 64

The step numbers shown below agree with the numbers shown in the circle symbols in the figure.
More DataQtyIdentificationNameTaskStep
(a)--Vertical Beam WebInspect1
(b)--Vertical Beam Outer
Chord
Inspect2
(a) Do a surface High Frequency Eddy Current (HFEC) inspection on the edge of the vertical beam web for
any crack in accordance with 747 NDT Manual Part 6, Section 51-00-00, Procedure 4 or 23. Inspect from
above the fastener common to the floor beam lower chord down to below the fastener, below the floor
beam chord. Extend the inspection to the mid-point towards the next adjacent fastener.
Use a pencil probe with a diameter that is less than 0.08 inch (2 mm). The following probes are examples
of probes that can be used:
1. MXTF-40, straight probe, 0.050 inch (1.27 mm) diameter. NDT Engineering Corp. (Olympus)
2. MXTF902-40B, right angle, 0.050 inch (1.27 mm) diameter. NDT Engineering Corp. (Olympus)
3. SPC/501/AI, right angle, 0.043 inch (1.09 mm) width, 0.5 inch (12.7 mm) drop. EC NDT Inc
(b) Do a surface HFEC inspection 360 degrees around the two fastener heads of the vertical beam outer
chord for any crack in accordance with 747 NDT Manual Part 6, Section 53-30-19.
FIGURE 5: LEFT SIDE STA 280-320 VERTICAL BEAM OUTER CHORD AND WEB – SURFACE HIGH
FREQUENCY EDDY CURRENT (HFEC) INSPECTION
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: December 02, 2015
747-53A2887
64 of 85
BOEING SERVICE BULLETIN 747-53A2887
ALERTALERT

### Page 65 (OCR)

BOEING SERVICE BULLETIN 747-53A2887
ALERT  ALERT
This Figure applies only to: Group 1, 4.
STA
260
STA
260
CANTED
STA
340
STA
280
STA
300
- LBL 22
- LBL 10
— RBL 10
• RBL 22
2456017
FIGURE 6: RIGHT SIDE STA 280-320 VERTICAL BEAM OUTER CHORD AND WEB - SURFACE HIGH
FREQUENCY EDDY CURRENT (HFEC) INSPECTION
(SHEET 1 OF 3)
Original Issue: December 02, 2015
Export Controlled ECCN: 9E991 - BOEING  747-53A2887
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  65 of 85

### Page 66 (OCR)

BOEING SERVICE BULLETIN 747-53A2887
ALERT  ALERT
STA
280
300
320
VERTICAL
BEAM WEB
CHORD
FLOOR
BEAM
TYPICAL
CRACK
INSPECTION AREA
FLOOR
BEAM
VERTICAL
BEAM OUTER -
CHORD
VERTICAL
BEAM WEB
A-A  2456021
FIGURE 6: RIGHT SIDE STA 280-320 VERTICAL BEAM OUTER CHORD AND WEB - SURFACE HIGH
FREQUENCY EDDY CURRENT (HFEC) INSPECTION
(SHEET 2 OF 3)
Original Issue: December 02, 2015
Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright © Unpublished  747-53A2887
Work - See page 1 for details.  66 of 85

### Page 67

The step numbers shown below agree with the numbers shown in the circle symbols in the figure.
More DataQtyIdentificationNameTaskStep
(a)--Vertical Beam WebInspect1
(b)--Vertical Beam Outer
Chord
Inspect2
(a) Do a surface High Frequency Eddy Current (HFEC) inspection on the edge of the vertical beam web for
any crack in accordance with 747 NDT Manual Part 6, Section 51-00-00, Procedure 4 or 23. Inspect from
above the fastener common to the floor beam lower chord down to below the fastener, below the floor
beam chord. Extend the inspection to the mid-point towards the next adjacent fastener.
Use a pencil probe with a diameter that is less than 0.08 inch (2 mm). The following probes are examples
of probes that can be used:
1. MXTF-40, straight probe, 0.050 inch (1.27 mm) diameter. NDT Engineering Corp. (Olympus)
2. MXTF902-40B, right angle, 0.050 inch (1.27 mm) diameter. NDT Engineering Corp. (Olympus)
3. SPC/501/AI, right angle, 0.043 inch (1.09 mm) width, 0.5 inch (12.7 mm) drop. EC NDT Inc
(b) Do a surface HFEC inspection 360 degrees around the two fastener heads of the vertical beam outer
chord for any crack in accordance with 747 NDT Manual Part 6, Section 53-30-19.
FIGURE 6: RIGHT SIDE STA 280-320 VERTICAL BEAM OUTER CHORD AND WEB – SURFACE HIGH
FREQUENCY EDDY CURRENT (HFEC) INSPECTION
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: December 02, 2015
747-53A2887
67 of 85
BOEING SERVICE BULLETIN 747-53A2887
ALERTALERT

### Page 68 (OCR)

BOEING SERVICE BULLETIN 747-53A2887
ALERT  ALERT
This Figure applies only to: Group 1, 4.
STA
260
STA  *STA
CANTED STA  260  ¡ 280
340
RBL 22.  STA  340
RBL 10 -
LBL 10 -
LBL 22 ~
2454904
FIGURE 7: LEFT SIDE STA 280-320 VERTICAL BEAM OUTER CHORD AND WEB - OPEN HOLE HIGH
FREQUENCY EDDY CURRENT (HFEC) INSPECTION
(SHEET 1 OF 2)
Original Issue: December 02, 2015
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  98 10 89

### Page 69

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
More DataQtyIdentificationNameTaskStep
Refer to 747-
100/200/300 SRM
51-30-02 or 747-SP
SRM 51-30-02 as an
accepted procedure.
6-FastenersRemove1
(a)--Vertical Beam WebInspect2
(a)--Vertical Beam Outer
Chord
Inspect
(a) Do an open hole High Frequency Eddy Current (HFEC) inspection for any crack in accordance with 747
NDT Manual Part 6, Section 51-00-00, Procedure 1, Procedure 11 or Procedure 16.
FIGURE 7: LEFT SIDE STA 280-320 VERTICAL BEAM OUTER CHORD AND WEB – OPEN HOLE HIGH
FREQUENCY EDDY CURRENT (HFEC) INSPECTION
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: December 02, 2015
747-53A2887
69 of 85
BOEING SERVICE BULLETIN 747-53A2887
ALERTALERT

### Page 70 (OCR)

BOEING SERVICE BULLETIN 747-53A2887
ALERT  ALERT
This Figure applies only to: Group 1, 4.
STA
260
STA
260
CANTED
- LBL 20
- LBL 10
- RBL 10
- RBL 22
2456072
FIGURE 8: RIGHT SIDE STA 280-320 VERTICAL BEAM OUTER CHORD AND WEB - OPEN HOLE HIGH
FREQUENCY EDDY CURRENT (HFEC) INSPECTION
(SHEET 1 OF 2)
Original Issue: December 02, 2015
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  98 10 0L

### Page 71

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
More DataQtyIdentificationNameTaskStep
Refer to 747-
100/200/300 SRM
51-30-02 or 747-SP
SRM 51-30-02 as an
accepted procedure.
6-FastenersRemove1
(a)--Vertical Beam WebInspect2
(a)--Vertical Beam Outer
Chord
Inspect
(a) Do an open hole High Frequency Eddy Current (HFEC) inspection for any crack in accordance with 747
NDT Manual Part 6, Section 51-00-00, Procedure 1, Procedure 11 or Procedure 16.
FIGURE 8: RIGHT SIDE STA 280-320 VERTICAL BEAM OUTER CHORD AND WEB – OPEN HOLE HIGH
FREQUENCY EDDY CURRENT (HFEC) INSPECTION
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: December 02, 2015
747-53A2887
71 of 85
BOEING SERVICE BULLETIN 747-53A2887
ALERTALERT

### Page 72 (OCR)

BOEING SERVICE BULLETIN 747-53A2887
ALERT  ALERT
This Figure applies only to: Group 1.
STA
260
STA  *STA
CANTED STA  260  ¡ 280
340
RBL 22.  STA  340
RBL 10 -
LBL 10 -
LBL 22 -
FIGURE 9: LEFT SIDE STA 280-320 VERTICAL BEAM OUTER CHORD AND WEB - RIVET INSTALLATION
(SHEET 1 OF 2)
Original Issue: December 02, 2015
Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright © Unpublished  747-53A2887
Work - See page 1 for details.  72 of 85

### Page 73

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
More DataQtyIdentificationNameTaskStep
(a) (b)6BACR15ET9D OR
BACR15BB10AD
RivetInstall (New)1
(a) Refer to 747-100/200/300 SRM 51-30-02 or 747-SP SRM 51-30-02 as an accepted procedure.
(b) The same size fasteners can be used if the quality of the existing hole meets SRM requirements. The
maximum size of any new fastener is 0.312" diameter, maintain 1.5D minimum edge margin.
FIGURE 9: LEFT SIDE STA 280-320 VERTICAL BEAM OUTER CHORD AND WEB – RIVET INSTALLATION
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: December 02, 2015
747-53A2887
73 of 85
BOEING SERVICE BULLETIN 747-53A2887
ALERTALERT

### Page 74 (OCR)

BOEING SERVICE BULLETIN 747-53A2887
ALERT  ALERT
This Figure applies only to: Group 1.
STA
260
STA
260
CANTED
STA
340  320  - LBL 22
— LBL 10
- RBL 10
RBL 22
2456080
FIGURE 10: RIGHT SIDE STA 280-320 VERTICAL BEAM OUTER CHORD AND WEB - RIVET INSTALLATION
(SHEET 1 OF 2)
Original Issue: December 02, 2015
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  S810 AL

### Page 75

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
More DataQtyIdentificationNameTaskStep
(a) (b)6BACR15ET9D OR
BACR15BB10AD
RivetInstall (New)1
(a) Refer to 747-100/200/300 SRM 51-30-02 or 747-SP SRM 51-30-02 as an accepted procedure.
(b) The same size fasteners can be used if the quality of the existing hole meets SRM requirements. The
maximum size of any new fastener is 0.312" diameter, maintain 1.5D minimum edge margin.
FIGURE 10: RIGHT SIDE STA 280-320 VERTICAL BEAM OUTER CHORD AND WEB – RIVET INSTALLATION
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: December 02, 2015
747-53A2887
75 of 85
BOEING SERVICE BULLETIN 747-53A2887
ALERTALERT

### Page 76 (OCR)

BOEING SERVICE BULLETIN 747-53A2887
ALERT  ALERT
This Figure applies only to: Group 4.
STA
260
STA  ^ STA
CANTED STA  260  ¡ 280
340
RBL 22.  STA  340
RBL 10 -
LBL 10 -
LBL 22 ~
2454871
FIGURE 11: LEFT SIDE STA 280-320 VERTICAL BEAM OUTER CHORD AND WEB - BOLT INSTALLATION
(SHEET 1 OF 2)
Original Issue: December 02, 2015
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  76 of 85

### Page 77

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
More DataQtyIdentificationNameTaskStep
(a) (b) (c) (d)6BACB30MY6K6X OR
BACB30MY6K6Y
BoltInstall (New)1
(a) (b) (c) (d)6BACC30M6 OR
BACC30AC6
CollarInstall (New)
(a) BACB30MY6K6X bolt is to be installed with a BACC30M6 collar. BACB30MY6K6Y bolt is to be installed
with a BACC30AC6 collar.
(b) Kept or the same size fasteners can be used if the quality of the existing hole meets SRM requirements.
The maximum size of any new fastener is 0.312" diameter, maintain 1.5D minimum edge margin.
(c) Install wet with BMS 5-95 sealant. Refer to SOPM 20-50-19 as an accepted procedure.
(d) Refer to 747-100/200/300 SRM 51-30-02 as an accepted procedure.
FIGURE 11: LEFT SIDE STA 280-320 VERTICAL BEAM OUTER CHORD AND WEB – BOLT INSTALLATION
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: December 02, 2015
747-53A2887
77 of 85
BOEING SERVICE BULLETIN 747-53A2887
ALERTALERT

### Page 78 (OCR)

BOEING SERVICE BULLETIN 747-53A2887
ALERT  ALERT
This Figure applies only to: Group 4.
STA
260
STA
260
CANTED
STA
340
STA
300
STA  STA
340  320  LBL 22
-LBL 10
- RBL 10
- RBL 22
2456077
FIGURE 12: RIGHT SIDE STA 280-320 VERTICAL BEAM OUTER CHORD AND WEB - BOLT INSTALLATION
(SHEET 1 OF 2)
Original Issue: December 02, 2015
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  98 10 82

### Page 79

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
More DataQtyIdentificationNameTaskStep
(a) (b) (c) (d)6BACB30MY6K6X OR
BACB30MY6K6Y
BoltInstall (New)1
(a) (b) (c) (d)6BACC30M6 OR
BACC30AC6
CollarInstall (New)
(a) BACB30MY6K6X bolt is to be installed with a BACC30M6 collar. BACB30MY6K6Y bolt is to be installed
with a BACC30AC6 collar.
(b) Kept or the same size fasteners can be used if the quality of the existing hole meets SRM requirements.
The maximum size of any new fastener is 0.312" diameter, maintain 1.5D minimum edge margin.
(c) Install wet with BMS 5-95 sealant. Refer to SOPM 20-50-19 as an accepted procedure.
(d) Refer to 747-100/200/300 SRM 51-30-02 as an accepted procedure.
FIGURE 12: RIGHT SIDE STA 280-320 VERTICAL BEAM OUTER CHORD AND WEB – BOLT INSTALLATION
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: December 02, 2015
747-53A2887
79 of 85
BOEING SERVICE BULLETIN 747-53A2887
ALERTALERT

### Page 80

This Appendix applies only to: Group 1, 4.
Logic diagrams are provided as an aid only. Information contained in Paragraph 1.E., Compliance is the primary
source for compliance times. Information contained in Paragraph 3.B., Work Instructions is the primary source
for tasks required for compliance.
1. The table below gives the description for the parts and conditions called out in the logic diagrams.
DescriptionTitle
MODIFICATION.PART 1
NOSE WHEEL WELL BODY STRUCTURE DETAILED INSPECTION.PART 2
STA 280-320 VERTICAL BEAM OUTER CHORD AND WEB SURFACE OR
OPEN HOLE HIGH FREQUENCY EDDY CURRENT (HFEC) INSPECTION.
PART 3
SECONDARY INSPECTION AND REPAIR.PART 4
ANY CRACK FOUND during PART 2.CONDITION 1
NO CRACK FOUND during PART 2.CONDITION 2
SURFACE HIGH FREQUENCY EDDY CURRENT (HFEC) INSPECTION
DONE. ANY CRACK FOUND during PART 3.
CONDITION 3
SURFACE HIGH FREQUENCY EDDY CURRENT (HFEC) INSPECTION
DONE. NO CRACK FOUND during PART 3.
CONDITION 4
OPEN HOLE HIGH FREQUENCY EDDY CURRENT (HFEC) INSPECTION
DONE. ANY CRACK FOUND during PART 3.
CONDITION 5
OPEN HOLE HIGH FREQUENCY EDDY CURRENT (HFEC) INSPECTION
DONE. NO CRACK FOUND during PART 3.
CONDITION 6
APPENDIX A:  LOGIC DIAGRAM FOR TABLE 1 - MODIFICATION AND INSPECTION
(SHEET 1 OF 4)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: December 02, 2015
747-53A2887
80 of 85
BOEING SERVICE BULLETIN 747-53A2887
ALERTALERT

### Page 81

APPENDIX A:  LOGIC DIAGRAM FOR TABLE 1 - MODIFICATION AND INSPECTION
(SHEET 2 OF 4)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: December 02, 2015
747-53A2887
81 of 85
BOEING SERVICE BULLETIN 747-53A2887
ALERTALERT

### Page 82 (OCR)

BOEING SERVICE BULLETIN 747-53A2887
ALERT  ALERT
WHICHEVER OCCURS LATER
WITHIN 12
BEFORE  WITHIN 3,000  MONTHS AFTER
25,000 TOTAL  FLIGHT CYCLES  THE ORIGINAL
FLIGHT  AFTER THE PART  ISSUE DATE OF
CYCLES  1 MODIFICATION  THIS SERVICE
BULLETIN
DO PART 2
CONDITION 1  CONDITION 2
NOT TO EXCEED
BEFORE FURTHER  3,000 FLIGHT
FLIGHT  CYCLES
REPEAT PART 2 AT
DO PART 4  UNREPAIRED AREAS ONLY
NOT TO EXCEED 3,000
FLIGHT CYCLES
REPEAT PART 2 AT
UNREPAIRED AREAS ONLY  2459396
APPENDIX A: LOGIC DIAGRAM FOR TABLE 1 - MODIFICATION AND INSPECTION
(SHEET 3 OF 4)
Original Issue: December 02, 2015
Export Controlled ECCN: 9E991 - BOEING  747-53A2887
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  82 of 85

### Page 83 (OCR)

BOEING SERVICE BULLETIN 747-53A2887
ALERT  ALERT
WHICHEVER OCCURS LATER
WITHIN 2,200 FLIGHT
BEFORE 30,000 TOTAL  FLIGHT CYCLES  CYCLES AFTER THE  ORIGINAL ISSUE DATE  OF THIS SERVICE
BULLETIN
DO PART 3
CONDITION 3  CONDITION 4  CONDITION 5  CONDITION 6
BEFORE FURTHER  NOT TO EXCEED 3,000  BEFORE FURTHER  BEFORE FURTHER
FLIGHT  FLIGHT CYCLES  FLIGHT  FLIGHT
DO PART 4  DO PART 4  INSTALL NEW
FASTENERS
NOT TO EXCEED 3,000
NOT TO EXCEED 6,000
FLIGHT CYCLES
FLIGHT CYCLES
REPEAT PART 3 AT
UNREPAIRED AREAS
ONLY  REPEAT PART 3 AT
UNREPAIRED AREAS
ONLY
2459997
APPENDIX A: LOGIC DIAGRAM FOR TABLE 1 - MODIFICATION AND INSPECTION
(SHEET 4 OF 4)
Original Issue: December 02, 2015
PROPRIETARY - Copyright ® Unpublished  Export Controlled ECCN: 9E991 - BOEING  747-53A2887
Work - See page 1 for details.  83 of 85

### Page 84

This Appendix applies only to: Group 2-3, 5-6.
Logic diagrams are provided as an aid only. Information contained in Paragraph 1.E., Compliance is the primary
source for compliance times. Information contained in Paragraph 3.B., Work Instructions is the primary source
for tasks required for compliance.
1. The table below gives the description for the parts and conditions called out in the logic diagrams.
DescriptionTitle
NOSE WHEEL WELL BODY STRUCTURE DETAILED INSPECTION.PART 2
SECONDARY INSPECTION AND REPAIR.PART 4
ANY CRACK FOUND during PART 2.CONDITION 1
NO CRACK FOUND during PART 2.CONDITION 2
APPENDIX B:  LOGIC DIAGRAM FOR TABLE 2 - DETAILED INSPECTION
(SHEET 1 OF 2)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: December 02, 2015
747-53A2887
84 of 85
BOEING SERVICE BULLETIN 747-53A2887
ALERTALERT

The text continues at https://openairdocs.org/service-documents/boeing/747-53a2887/file/1f0cd8aee6e2.md?from=85

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
