# Boeing Alert Requirements Bulletin 747-53A2911 RB: No revision named

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2023-0934; AD 2023-14-03 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Alert Requirements Bulletin 747-53A2911 RB](https://openairdocs.org/service-documents/boeing/747-53a2911-rb.md)
- Title as filed: RB-747-53A2911RB
- Pages: 21
- PDF: https://openairdocs.org/files/sha256/05/84/058447d41fe8814d6782c7bb7d91c20c75b4c36b55c211759832e98d86ccae76
- Page: https://openairdocs.org/service-documents/boeing/747-53a2911-rb/file/058447d41fe8

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Commercial 
Airplanes
747
Requirements Bulletin
ALERT
Number: 747-53A2911 RB
Original Issue: November 03, 2022
ATA System: 5321 5313
SUBJECT: FUSELAGE - Internal Structure - Stringers Forward and Aft of the Bulkhead at STA
2598 Inspection
EXPORT CONTROLLED - This technology or software is subject to the U.S. Export Administration Regulations
(EAR), (15 C.F.R. Parts 730-774). No authorization from the U.S. Department of Commerce is required for
export, re-export, in-country transfer, or access EXCEPT to country group E:1 or E:2 countries/persons per
Supp.1 to Part 740 of the EAR.
9E991ECCN:
Copyright © 2022 Boeing.
Unpublished Work. All Rights Reserved.
Treatment of this document and its content is governed by contract with Boeing. Rights to use this document
are licensed on a per aircraft basis and such rights may not be transferable. For more information, contact The
Boeing Company.
Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner,
BBJ, DC-8, DC-9, DC-10, KC-10, KC-46, KDC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8, Poseidon and
Boeing liveries are all trademarks owned by The Boeing Company; and no trademark license is granted in
connection with this document unless provided in writing by Boeing.
Original Issue: November 03, 2022
747-53A2911 RB
1 of 21
2.0

### Page 2

Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: November 03, 2022
747-53A2911 RB
2 of 21
REQUIREMENTS BULLETIN 747-53A2911
ALERTALERT
BLANK PAGE

### Page 3

Table of Contents
1. EFFECTIVITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
A. Airplanes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
B. Spares Affected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2. CONCURRENT REQUIREMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3. COMPLIANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4. APPROVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
5. ACCOMPLISHMENT INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
A. General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
B. Work Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
FIGURE 1: LOWER LOBE STRINGERS FORWARD OF THE BULKHEAD AT STA 2598 - INSPECTION
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
FIGURE 2: LOWER LOBE STRINGERS AFT OF THE BULKHEAD AT STA 2598 AND ALL CROWN
STRINGERS - INSPECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: November 03, 2022
747-53A2911 RB
3 of 21
REQUIREMENTS BULLETIN 747-53A2911
ALERTALERT

### Page 4

Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: November 03, 2022
747-53A2911 RB
4 of 21
REQUIREMENTS BULLETIN 747-53A2911
ALERTALERT
BLANK PAGE

### Page 5

Commercial 
Airplanes
747
Requirements Bulletin
ALERT
Number: 747-53A2911 RB
Original Issue: November 03, 2022
ATA System: 5321 5313
SUBJECT: FUSELAGE - Internal Structure - Stringers Forward and Aft of the Bulkhead at STA
2598 Inspection
THIS DOCUMENT IS SENT TO THE OPERATORS OF RECORD OF THE AIRPLANES SHOWN IN
PARAGRAPH 1.A., EFFECTIVITY. IF AN AIRPLANE HAS BEEN LEASED OR SOLD, SEND THIS DOCUMENT
TO THE NEW OPERATOR. IF APPLICABLE SPARES HAVE BEEN SOLD, SEND THIS DOCUMENT TO THE
NEW OWNER. THIS IS AN ENHANCED REQUIRED FOR COMPLIANCE DOCUMENT. THE BOEING
PROCESSES USED TO CREATE THE SERVICE BULLETIN (SB) AND THE REQUIREMENTS BULLETIN
(RB) ENSURE THAT THE INFORMATION BETWEEN "RC START" AND "RC END" IN THE SB ARE IDENTICAL
TO THE INFORMATION IN THE SAME SECTIONS (COMPLIANCE, WORK INSTRUCTIONS…) OF THE RB
WHICH THE SB REFERS TO AS THE RELATED DOCUMENT.
1. Effectivity
A. Airplanes
This bulletin is applicable to 747-8, 747-8F Airplane(s), line number(s) 1420-9999 in 1 Group(s).
Where the effectivity is presented with hyphens between line numbers, the airplane applicability
means "through" and "inclusive", e.g. line numbers 1-9 means line numbers 1 through 9 inclusive.
The Variable Numbers and Group Information for the applicable airplanes is given below.
NOTE: The Variable Number table below includes affected airplanes available as of the issue
date of this bulletin. Affected airplane Variable Numbers added to MyBoeingFleet.com
after the issue date of this bulletin will be shown using the Maintenance Performance
Toolbox EFFECTIVITY search function result.
DESCRIPTIONCONFIGURATIONGROUP
747-8/-8F Airplanes.-1
Airplane Models:
747-8, 747-8F
GroupVariable Number
1RC001 - RC009
1RC021 - RC040
GroupVariable Number
1RC051 - RC060
1RC066 - RC072
GroupVariable Number
1RC076 - RC077
1RC501 - RC514
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: November 03, 2022
747-53A2911 RB
5 of 21

### Page 6

GroupVariable Number
1RC521 - RC528
1RC531 - RC541
1RC546 - RC566
1RC571 - RC582
GroupVariable Number
1RC601 - RC610
1RC641 - RC644
1RC651 - RC652
1RC661
GroupVariable Number
1RC671 - RC674
1RC681 - RC696
1RC701 - RC704
--
B. Spares Affected
None.
2. CONCURRENT REQUIREMENTS
None.
3. COMPLIANCE
The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to
Requirements Bulletin 747-53A2911 RB. The Airworthiness Directive will make the compliance tasks and
times given in Requirements Bulletin 747-53A2911 RB mandatory.
Accomplish the required action(s), based on the applicable condition(s) in Table 1, in accordance with
Accomplishment Instructions.
When more than one OPTION is given for a CONDITION, do only one of the OPTION numbers. When
more than one ACTION is given for a CONDITION or an OPTION, do all of the ACTION numbers for that
CONDITION or OPTION.
Table 1: Inspection of Stringers Forward and Aft of the Bulkhead at STA 2598
Repeat Interval
(Not to Exceed)
Boeing Recommended
Compliance Time
(Whichever Occurs Later)
ActionCondition
-Within 32
months after the
Original Issue
date of Require-
ments Bulletin
747-53A2911
RB.
Before 8,000 total
flight cycles or with-
in 8 years after the
date of issuance of
the original standard
certificate of airwor-
thiness or the origi-
nal export certificate
of airworthiness,
whichever occurs
first.
Do a detailed inspection of
stringers forward and aft of
the bulkhead at STA 2598
for any crack.
All Airplanes.
8,000 flight cycles
or 8 years,
whichever occurs
first.
-Repeat the detailed inspec-
tion of stringers forward and
aft of the bulkhead at STA
2598 for any crack.
CONDITION 1:
NO CRACK FOUND
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: November 03, 2022
747-53A2911 RB
6 of 21
REQUIREMENTS BULLETIN 747-53A2911
ALERTALERT

### Page 7

Table 1: Inspection of Stringers Forward and Aft of the Bulkhead at STA 2598
Repeat Interval
(Not to Exceed)
Boeing Recommended
Compliance Time
(Whichever Occurs Later)
ActionCondition
-Before further flight.CONDITION 2 (ACTION 1):CONDITION 2:
Contact The Boeing Compa-
ny for repair instructions and
do the repair.
ANY CRACK
FOUND
8,000 flight cycles
or 8 years,
whichever occurs
first.
-CONDITION 2 (ACTION 2):
Repeat the detailed inspec-
tion of stringers forward and
aft of the bulkhead at STA
2598 for any crack.
4. APPROVAL
This Requirements Bulletin was examined by the Federal Aviation Administration (FAA). The changes
specified in this document comply with the applicable regulations and are FAA approved, as well as European
Union Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved
airplanes listed in this Requirements Bulletin effectivity. This document and its approval were based on the
airplane in its original Boeing delivery configuration or as modified by other Boeing changes.
If an airplane has a non-Boeing modification or repair that affects a component or system also affected by
this Requirements Bulletin, the operator is responsible for obtaining appropriate regulatory agency approval
before incorporating this Requirements Bulletin.
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: November 03, 2022
747-53A2911 RB
7 of 21
REQUIREMENTS BULLETIN 747-53A2911
ALERTALERT

### Page 8

Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: November 03, 2022
747-53A2911 RB
8 of 21
REQUIREMENTS BULLETIN 747-53A2911
ALERTALERT
BLANK PAGE

### Page 9

5.    ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL INFORMATION
NOTE: 1. This is an Enhanced Required for Compliance document. There will be a separate
Service Bulletin (SB) and a separate Requirements Bulletin (RB). If an RB is mandated
by an Airworthiness Directive (AD), then all applicable requirements specified in the
RB must be done. For the related SB, some locations are marked RC Start and RC
End to identify the requirements that are restated from the RB. For the related SB,
the areas between RC Start and RC End, including sub-steps and any figures
identified between RC Start and RC End, must be done to comply with the AD.
Therefore, an Alternative Method of Compliance (AMOC) is required for any deviations
to steps between RC Start and RC End, including substeps and identified figures.
For the related SB, the steps not between RC Start and RC End may be deviated
from using accepted methods in accordance with the operator's maintenance or
inspection program without obtaining approval of an AMOC; this is provided that the
steps between RC Start and RC End, including sub-steps and identified figures, can
still be done as specified, and the airplane can be put back in an airworthy condition.
Figures not required for compliance are omitted from the RB.
2. This is an Enhanced Required for Compliance document. The Boeing processes
used to create the Service Bulletin (SB) and the Requirements Bulletin (RB) ensure
that the information between "RC Start" and "RC End" in the SB are identical to the
information in the same sections (Compliance, Work Instructions...) of the RB which
the SB refers to as the related document.
3. The compliance times for the actions in WORK INSTRUCTIONS are in Compliance.
4. Boeing Service Letter 747-SL-51-048, Damage Reporting and Repair Plan/Design
Guidelines, is an acceptable procedure to request information from Boeing for
additional structural repair instructions. The Service Letter describes what information
must be provided to Boeing before a structural repair can be provided.
5. Unless shown differently, these dimensions and tolerances are used:
– Linear dimensions are in inches
– Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus
or minus 0.03 inch
– Tolerance on rivet and bolt edge margin is plus or minus 0.05 inch
– Angular tolerance is plus or minus 2 degrees
– Hole dimensions for standard solid rivets and fasteners are in Structural Repair
Manual (SRM) Chapter 51
– Torque Values:
— Values for structural fasteners are given in 747 Structural Repair Manual,
Chapter 51.
— Values for airframe maintenance tasks are included in Chapter 20 of 747
Aircraft Maintenance Manual (AMM).
— Non-standard torque values for maintenance tasks are included in the
applicable installation step.
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: November 03, 2022
747-53A2911 RB
9 of 21
REQUIREMENTS BULLETIN 747-53A2911
ALERTALERT

### Page 10

6. These work instructions refer to procedures included in other Boeing documents.
When the words "refer to" are used and the operator has an accepted alternative
procedure, the accepted alternative procedure can be used. When the words "in
accordance with" are included in the instruction, the procedure in the Boeing document
must be used.
7. Where the work instructions include installation of a kept part, a new or serviceable
part with the same part number can be installed as an alternative to the kept part.
8. If it is necessary to remove more parts for access, you can remove those parts. If
you can get access without removing identified parts, it is not necessary to remove
all of the identified parts. Jacking and shoring limitations must be observed.
9. Use the approved fastener, process and material substitutions in accordance with
SRM Chapter 51.
10. A Detailed Inspection is defined as: An intensive examination of a specific item,
installation or assembly to detect damage, failure or irregularity. This could include
tactile assessment in which a component or assembly can be checked for
tightness/security. Available lighting is normally supplemented with a direct source
of good lighting at an intensity deemed appropriate. Inspection aids such as mirrors
and magnifying lenses may be necessary. Surface cleaning and elaborate access
procedures may be required.
11. When more than one OPTION is given for a CONDITION, do only one of the OPTION
numbers. When more than one ACTION is given for a CONDITION or an OPTION,
do all of the ACTION numbers for that CONDITION or OPTION.
B. WORK INSTRUCTIONS
Actions Required For Compliance
1. Requirements
Table 1: Inspection of Stringers Forward and Aft of the Bulkhead at STA 2598
Refer to the listed
procedures in SB
747-53A2911
Original Issue or
later approved re-
visions as an ac-
cepted proce-
dure.
Method of ComplianceActionCondition
Do PART 1: OPEN
ACCESS
-Do a detailed inspection of
stringers forward and aft of
the bulkhead at STA 2598
for any crack.
All Airplanes.
-FIGURE 1 and FIGURE 2
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: November 03, 2022
747-53A2911 RB
10 of 21
REQUIREMENTS BULLETIN 747-53A2911
ALERTALERT

### Page 11

Table 1: Inspection of Stringers Forward and Aft of the Bulkhead at STA 2598
Refer to the listed
procedures in SB
747-53A2911
Original Issue or
later approved re-
visions as an ac-
cepted proce-
dure.
Method of ComplianceActionCondition
Do PART 2:
CLOSE ACCESS
-Repeat the detailed inspec-
tion of stringers forward and
aft of the bulkhead at STA
2598 for any crack.
CONDITION 1:
NO CRACK FOUND
-FIGURE 1 and FIGURE 2
--CONDITION 2 (ACTION 1):CONDITION 2:
Contact The Boeing Compa-
ny for repair instructions
and do the repair.
ANY CRACK FOUND
Do PART 2:
CLOSE ACCESS
-CONDITION 2 (ACTION 2):
Repeat the detailed inspec-
tion of stringers forward and
aft of the bulkhead at STA
2598 for any crack.
-FIGURE 1 and FIGURE 2
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: November 03, 2022
747-53A2911 RB
11 of 21
REQUIREMENTS BULLETIN 747-53A2911
ALERTALERT

### Page 12 (OCR)

REQUIREMENTS BULLETIN 747-53A2911
ALERT  ALERT
STA
2598  STA
2598
S-24L
S-25L
S-26L
S-38L
S-42L
S-46L
S-49L
S-51L
S-51R
S-49R
S-46R
S-42R
S-38R
S-26R
S-25R
S-24R
STA
FWD  2598  • FRAME
STRINGER AND END FITTING
(BULKHEAD NOT SHOWN)  END FITTING
(TYPICAL)
2999549
FIGURE 1: LOWER LOBE STRINGERS FORWARD OF THE BULKHEAD AT STA 2598 - INSPECTION
(SHEET 1 OF 4)
Original Issue: November 03, 2022
747-53A2911 RB
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.  12 of 21

### Page 13 (OCR)

REQUIREMENTS BULLETIN 747-53A2911
ALERT  ALERT
SKIN
EDGE OF
EDGE OF  TYPICAL CRACK  END FITTING
STRINGER
END FITTING
STRINGER AND END FITTING
(TYPICAL)
A-A  FWD
TYPICAL CRACK
END FITTING
EDGE OF
END FITTING
EDGE OF
STRINGER
-SKIN
STRINGER AND END FITTING
(TYPICAL)  FWD
B-B
TYPICAL CRACK  EDGE OF
END FITTING
EDGE OF
STRINGER
END FITTING
STRINGER AND END FITTING
INSPECTION AREA  (SPACERS NOT SHOWN)  (TYPICAL)  2999552
C-C
FIGURE 1: LOWER LOBE STRINGERS FORWARD OF THE BULKHEAD AT STA 2598 - INSPECTION
(SHEET 2 OF 4)
Original Issue: November 03, 2022
Export Controlled ECCN: 9E991  747-53A2911 RB
Copyright © Unpublished Work - See page 1 for details.  13 of 21

### Page 14 (OCR)

REQUIREMENTS BULLETIN 747-53A2911
ALERT  ALERT
STA
2598  •FRAME
D
FWD
• o
STRINGER AND STRINGER END TIE  (BULKHEAD NOT SHOWN)  E
STRINGER
END TIE
EDGE OF  TYPICAL  SKIN
STRINGER  CRACK
FRAME
STRINGER
END TIE
D-D  FWD
TYPICAL
CRACK
STRINGER
END TIE-
SKIN
FRAME-
EDGE OF
STRINGER  E-E  FWD
INSPECTION AREA  3011104
FIGURE 1: LOWER LOBE STRINGERS FORWARD OF THE BULKHEAD AT STA 2598 - INSPECTION
(SHEET 3 OF 4)
Original Issue: November 03, 2022
747-53A2911 RB
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.  14 of 21

### Page 15

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for figure.
More DataQtyIdentificationNameTaskStep
(a)1-S-24L, STA 2598Inspect1
(a)1-S-25L, STA 2598Inspect
(a)1-S-26L, STA 2598Inspect
(a)1-S-42L, STA 2598Inspect
(a)1-S-46L, STA 2598Inspect
(a)1-S-49L, STA 2598Inspect
(a)1-S-51L, STA 2598Inspect
(a)1-S-51R, STA 2598Inspect
(a)1-S-49R, STA 2598Inspect
(a)1-S-46R, STA 2598Inspect
(a)1-S-42R, STA 2598Inspect
(a)1-S-26R, STA 2598Inspect
(a)1-S-25R, STA 2598Inspect
(a)1-S-24R, STA 2598Inspect
(a)1-S-38R, STA 2598Inspect2
(a)1-S-38L, STA 2598Inspect
(a) Do a detailed inspection of stringers forward of the bulkhead at STA 2598 for any crack.
FIGURE 1: LOWER LOBE STRINGERS FORWARD OF THE BULKHEAD AT STA 2598 - INSPECTION
(SHEET 4 OF 4)
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: November 03, 2022
747-53A2911 RB
15 of 21
REQUIREMENTS BULLETIN 747-53A2911
ALERTALERT

### Page 16 (OCR)

REQUIREMENTS BULLETIN 747-53A2911
ALERT  ALERT
STA  STA
2598  2598
S-17R
S-16R
S-15R
S-14R
S-13R
S-12R
S-11R
S-10R
S-9R  A 40 LOCATIONS
S-8R
S-7R
S-6R
S
S-4R
S-3R  14 LOCATIONS  2598  STA
S-2R
S-1R  S-24L
BL-O  S-25L
S-1L  S-26L
S-2L
S-38L
S-3L  S-42L
S-46L
S-  5l
S-49L
S-I
S-51L
S-7L
S-8L  S-51R
S-9L  S-49R
S-10L  S-46R
S-11L  S-42R
S-12L  S-38R
S-13L  S-26R
S-14L  S-25R
S-15L  S-24R
S-16L
S-17L
2999776
FIGURE 2: LOWER LOBE STRINGERS AFT OF THE BULKHEAD AT STA 2598 AND ALL CROWN
STRINGERS - INSPECTION
(SHEET 1 OF 6)
Original Issue: November 03, 2022
747-53A2911 RB
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.  16 of 21

### Page 17 (OCR)

REQUIREMENTS BULLETIN 747-53A2911
ALERT  ALERT
END FITTING
STA
2598
FRAME
B
STRINGER AND END FITTING
(BULKHEAD NOT SHOWN)
(TYPICAL)
SKIN
TYPICAL CRACK
EDGE OF  EDGE OF
END FITTING  STRINGER
-END FITTING
STRINGER AND END FITTING
(TYPICAL)
A-A
INSPECTION AREA
FIGURE 2: LOWER LOBE STRINGERS AFT OF THE BULKHEAD AT STA 2598 AND ALL CROWN
STRINGERS - INSPECTION
(SHEET 2 OF 6)
Original Issue: November 03, 2022
747-53A2911 RB
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.  17 of 21

### Page 18 (OCR)

REQUIREMENTS BULLETIN 747-53A2911
ALERT  ALERT
TYPICAL CRACK
EDGE OF
END FITTING
END
FITTING
SKIN  EDGE OF
STRINGER
STRINGER AND END FITTINC
TYPICAL
B-B
EDGE OF  TYPICAL CRACK
END FITTING  EDGE OF
STRINGER
END
FITTING
O
STRINGER AND END FITTING
(SPACERS NOT SHOWN)
(TYPICAL)
C-C
INSPECTION AREA  2999801
FIGURE 2: LOWER LOBE STRINGERS AFT OF THE BULKHEAD AT STA 2598 AND ALL CROWN
STRINGERS - INSPECTION
(SHEET 3 OF 6)
Original Issue: November 03, 2022
Export Controlled ECCN: 9E991  747-53A2911 RB
Copyright © Unpublished Work - See page 1 for details.  18 of 21

### Page 19 (OCR)

REQUIREMENTS BULLETIN 747-53A2911
ALERT  ALERT
STA
2598  • FRAME
10001E
D
STRINGER AND STRINGER END TIE
(BULKHEAD NOT SHOWN)
STRINGER
END TIE
EDGE OF  TYPICAL  CRACK  SKIN
STRINGER
FRAME
STRINGER
END TIE
FWD  D-D
STRINGER  END TIE•  TYPICAL  CRACK
FRAME"
EDGE OF
STRINGER
E-E  SKIN
INSPECTION AREA  3011107
FIGURE 2: LOWER LOBE STRINGERS AFT OF THE BULKHEAD AT STA 2598 AND ALL CROWN
STRINGERS - INSPECTION
(SHEET 4 OF 6)
Original Issue: November 03, 2022
Export Controlled ECCN: 9E991  747-53A2911 RB
Copyright © Unpublished Work - See page 1 for details.  19 of 21

### Page 20

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for figure.
More DataQtyIdentificationNameTaskStep
(a)2-S-10R, STA 2598Inspect1
(a)2-S-9R, STA 2598Inspect
(a)2-S-8R, STA 2598Inspect
(a)2-S-7R, STA 2598Inspect
(a)2-S-6R, STA 2598Inspect
(a)2-S-5R, STA 2598Inspect
(a)2-S-4R, STA 2598Inspect
(a)2-S-3R, STA 2598Inspect
(a)2-S-2R, STA 2598Inspect
(a)2-S-1R, STA 2598Inspect
(a)2-S-1L, STA 2598Inspect
(a)2-S-2L, STA 2598Inspect
(a)2-S-3L, STA 2598Inspect
(a)2-S-4L, STA 2598Inspect
(a)2-S-5L, STA 2598Inspect
(a)2-S-6L, STA 2598Inspect
(a)2-S-7L, STA 2598Inspect
(a)2-S-8L, STA 2598Inspect
(a)2-S-9L, STA 2598Inspect
(a)2-S-10L, STA 2598Inspect
(b)1-S-24L, STA 2598Inspect
(b)1-S-25L, STA 2598Inspect
(b)1-S-26L, STA 2598Inspect
(b)1-S-42L, STA 2598Inspect
(b)1-S-46L, STA 2598Inspect
(b)1-S-49L, STA 2598Inspect
(b)1-S-51L, STA 2598Inspect
(b)1-S-51R, STA 2598Inspect
(b)1-S-49R, STA 2598Inspect
FIGURE 2: LOWER LOBE STRINGERS AFT OF THE BULKHEAD AT STA 2598 AND ALL CROWN
STRINGERS - INSPECTION
(SHEET 5 OF 6)
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: November 03, 2022
747-53A2911 RB
20 of 21
REQUIREMENTS BULLETIN 747-53A2911
ALERTALERT

### Page 21

More DataQtyIdentificationNameTaskStep
Inspect (b)1-S-46R, STA 2598
(b)1-S-42R, STA 2598Inspect
(b)1-S-26R, STA 2598Inspect
(b)1-S-25R, STA 2598Inspect
(b)1-S-24R, STA 2598Inspect
(b)1-S-12L, STA 2598Inspect2
(b)1-S-17L, STA 2598Inspect
(b)1-S-12R, STA 2598Inspect
(b)1-S-17R, STA 2598Inspect
(a) Do a detailed inspection of stringer forward and aft of the bulkhead at STA 2598 for any crack.
(b) Do a detailed inspection of the stringer aft of STA 2598 for any crack.
FIGURE 2: LOWER LOBE STRINGERS AFT OF THE BULKHEAD AT STA 2598 AND ALL CROWN
STRINGERS - INSPECTION
(SHEET 6 OF 6)
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: November 03, 2022
747-53A2911 RB
21 of 21
REQUIREMENTS BULLETIN 747-53A2911
ALERTALERT

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
