# Boeing Alert Service Bulletin 747-54A2203: U.S. DOT/FAA - Service Bulletin

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2010-0679; AD 2011-05-11 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Alert Service Bulletin 747-54A2203](https://openairdocs.org/service-documents/boeing/747-54a2203.md)
- Title as filed: U.S. DOT/FAA - Service Bulletin
- Pages: 102
- PDF: https://openairdocs.org/files/sha256/5c/92/5c9261159331b3a3c492e2af7e6c4d1c60b5292518136d95bc11f0e5fffe4230
- Page: https://openairdocs.org/service-documents/boeing/747-54a2203/file/5c9261159331

## Text

Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

August 31, 2000
Revision 2:  July 09, 2009 747-54A2203
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 1 of 102
 
 
ALERT ALERT
Commercial
Airplane
Group 747
ALERTALERT
Service Bulletin
Number: 747-54A2203
Date: August 31, 2000
Revision 2: July 09, 2009
ATA System: 5441
SUBJECT: NACELLES/PYLONS - Strut Forward Engine Mount - Inspection/Rework
BOEING PROPRIETARY, CONFIDENTIAL, AND/OR TRADE SECRET
Copyright © 2000 The Boeing Company
Unpublished Work - All Rights Reserved
Boeing claims copyright in each page of this document only to the extent that the page contains copyrightable 
subject matter.  Boeing also claims copyright in this document as a compilation and/or collective work.
This document includes proprietary information owned by The Boeing Company and/or one or more third 
parties.  Treatment of the document and the information it contains is governed by contract with Boeing.  For 
more information, contact The Boeing Company, P.O. Box 3707, Seattle, Washington 98124.
Boeing, 707, 717, 727, 737, 747, 757, 767, 777, BBJ, BOEING BUSINESS JET, DC-8, DC-9, DC-10, MD-10, 
MD-11, MD-80, MD-90, the Boeing logo and the Boeing livery are among the trademarks owned by Boeing or 
its subsidiaries. No intellectual property license (express or implied) is granted in connection with this document 
or otherwise.

### Page 2

BLANK PAGE
August 31, 2000
Revision 2:  July 09, 2009 747-54A2203
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 2 of 102
BOEING SERVICE BULLETIN 747-54A2203
ALERT                                                                                                    ALERT
 
 
BLANK PAGE

### Page 3

Table of Contents
August 31, 2000
Revision 2:  July 09, 2009 747-54A2203
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 3 of 102
BOEING SERVICE BULLETIN 747-54A2203
ALERT                                                                                                    ALERT
 
 
Table of Contents
Revision Transmittal Sheet .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 5
Summary .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 7
1. PLANNING INFORMATION .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  11
A. Effectivity .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  11
1. Airplanes   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  11
2. Spares Affected .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  19
B. Concurrent Requirements  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .   .  19
C. Reason .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  19
D. Description .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  22
E. Compliance.  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .   .  .  .  .  24
F. Approval .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  29
G. Manpower   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .   .  .  .  .  29
H. Weight and Balance Changes  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  30
I. Electrical Load Data  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .   .  .  .  30
J. References .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .   .  .  .  .  31
1. Existing Data: .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  31
2. Data supplied with this Service Bulletin:   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  31
3. Installation Drawings Used in the Preparation of this Service Bulletin: .  .  .  .  .  .  .  .  .  .  31
K. Publications Affected .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  31
L. Interchangeability and Intermixability of Parts  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  31
2. MATERIAL INFORMATION .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  33
A. Material - Price and Availability.  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  33
B. Industry Support Information .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .   .  33
C. Parts Necessary For Each Airplane  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  33
1. Kits/Parts: .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  33
2. Parts and Materials Supplied by the Operator:  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  33
3. Parts Modified and Reidentified:   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  34
4. Parts Removed and Not Replaced: .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  35
D. Parts Necessary to Change Spares  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  35
E. Special Tooling - Price and Availability.  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .   35
F. Special Tooling Necessary to do this Service Bulletin .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  35
3. ACCOMPLISHMENT INSTRUCTIONS .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  37
A. GENERAL INFORMATION   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  37
B. WORK INSTRUCTIONS .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  37
FIGURE  1:   LOGIC DIAGRAM  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  46
FIGURE  2:   FORWARD ENGINE MOUNT FITTING - DETAILED INSPECTION   .  .  .  .  .  .  .  .  .  .  .  47
FIGURE  3:   FORWARD ENGINE MOUNT FITTING - TORQUE CHECK   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  50
FIGURE  4:   FORWARD ENGINE MOUNT FITTING - ANY FASTENER FOUND UNDER-TORQUED OR
LOOSE - FASTENER RE-TIGHTENING .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  57
FIGURE  5:   THIS FIGURE HAS BEEN DELETED  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  64
FIGURE  6:   FORWARD ENGINE MOUNT FITTING REWORK  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  65
FIGURE  7:   FORWARD ENGINE MOUNT FITTING REPLACEMENT .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  76
FIGURE  8:   FORWARD ENGINE MOUNT - FASTENER REPLACEMENT  .  .  .  .  .  .  .  .  .  .  .  .  .  .  86
FIGURE  9: FORWARD ENGINE MOUNT - CHORD AND INTERNAL ANGLE INSPECTION  .  .  .  .  .  96
FIGURE  10: FORWARD ENGINE MOUNT BULKHEAD - INTERNAL BACK-UP STRUCTURE - ANGLE -

### Page 4

Table of Contents
August 31, 2000
Revision 2:  July 09, 2009 747-54A2203
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 4 of 102
BOEING SERVICE BULLETIN 747-54A2203
ALERT                                                                                                    ALERT
 
 
DET AND HFEC INSPECTION  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 98

### Page 5

Original Issue: August 31, 2000
Revision 2:  July 09, 2009 747-54A2203
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 5 of 102
 
 
ALERT ALERT
Commercial
Airplanes
747
ALERTALERT
Service Bulletin
Number: 747-54A2203 Revision Transmittal Sheet
Original Issue: August 31, 2000
Revision 2: July 09, 2009
ATA System: 5441
SUBJECT: NACELLES/PYLONS - Strut Forward Engine Mount - Inspection/Rework
This revision includes all pages of the service bulletin.
COMPLIANCE INFORMATION RELATED TO THIS REVISION
More work is necessary on airplanes which were not affected by the Original Issue or Revision 1 of this service 
bulletin.  These airplanes have hi-lok bolts and collars at all of  the Group B fastener locations, except fastener 
no.13.  These airplanes need to be inspected in accordance with Part 2 - Detailed Inspection, Torque Stripe 
Inspection, and Torque Check within 90 days after the date of Revision 2 of this service bulletin.  In addition, the 
fasteners on these airplanes need to be replaced in accordance with Part 6 - Fastener Replacement within 18 
months after the date of Revision 2 of this service bulletin.
NOTE: Terminating Action was removed from the service bulletin in revision 1.
REASON FOR REVISION
This revision is sent to do the following:
1. Add instructions for airplanes which were not affected by the Original Issue or Revision 1 of the service 
bulletin.  The inspections and fastener replacement in the Original Issue of this service bulletin were not 
required if two washers were installed under the nuts of the Group A fasteners or the pin protrusion was 
per the SRM.  When terminating action was removed from the service bulletin in revision 1, some operators 
reported that the fasteners types specified in Revision 1 did not match the fasteners on the airplane.  For 
airplanes not affected by the Original Issue, all of the Group B fasteners, except fastener no. 13, would 
have hi-lok bolts and collars installed and not the fasteners specified in Revision 1, as these airplanes were 
not required to replace the fasteners in the Original Issue.  The Group A and B fasteners on airplanes not 
affected by the Original Issue should be removed and replaced with the fasteners given in Revision 1 or 
Revision 2. 
2. Clarify the requirements in the torque stripe not applied and no under-torqued or loose fastener found 
action requirements by reordering the steps.
3. Added option to support engine weight instead of engine removal in Part 7 - HFEC Internal Angle 
Inspection. 
The following sections were changed as follows:

### Page 6

Original Issue: August 31, 2000
Revision 2:  July 09, 2009 747-54A2203
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 6 of 102
BOEING SERVICE BULLETIN 747-54A2203
ALERT                                                                                                    ALERT
 
 
1. Planning - Paragraph 1.E., Compliance.  Add requirements for airplanes not affected by the original 
release: See note (h).  Revise order of steps in the torque stripe not applied and no under-torqued or loose 
fastener found action requirements.
2. Accomplishment Instructions.  Revised Part 2 - Detailed Inspection, Torque Stripe Inspection, and Torque 
Check, Step 4., to add the requirements for airplanes which were not affected by the Original Issue or 
Revision 1 of this service bulletin and have hi-lok bolts and collars at all of  the Group B fastener locations, 
except fastener no. 13. 
3. Accomplishment Instructions. Revised Part 7 - HFEC Internal Angle Inspection to add option to support 
engine weight instead of engine removal. 
4. Figure 3.  Revised Table  2 - Torque Stripe not applied fastener looseness Inspection, Steps 7 and 8, to add 
the requirements for airplanes which were not affected by the Original Issue or Revision 1 of this service 
bulletin and have hi-lok bolts and collars at all of  the Group B fastener locations, except fastener no. 13. 
Paragraph 1.A., Effectivity, shows changes of airplane operators. Each operator should examine the Effectivity 
paragraph for changes.
Vertical lines are put on the left edge of each page, except in Paragraph 1.A., Effectivity, to show the location 
of important changes.
Pages with no vertical lines have no important changes.
REVISION HISTORY
Original Issue: August 31, 2000
Revision 1: August 9, 2007
Revision 2: July 9, 2009

### Page 7

August 31, 2000
Revision 2:  July 09, 2009 747-54A2203
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 7 of 102
 
 
ALERT ALERT
Commercial
Airplane
Group 747
ALERTALERT
Service Bulletin
Number: 747-54A2203 Summary
Date: August 31, 2000
Revision 2: July 09, 2009
ATA System: 5441
SUBJECT: NACELLES/PYLONS - Strut Forward Engine Mount - Inspection/Rework
THIS BULLETIN IS SENT TO THE OPERATORS OF RECORD OF THE AIRPLANES SHOWN IN 
PARAGRAPH 1.A., EFFECTIVITY.  IF AN AIRPLANE HAS BEEN LEASED OR SOLD, SEND THIS SERVICE 
BULLETIN TO THE NEW OPERATOR.  IF APPLICABLE SPARES HAVE BEEN SOLD, SEND THIS SERVICE 
BULLETIN TO THE NEW OWNER.
CONCURRENT REQUIREMENTS
None
BACKGROUND
This inspection, when completed, will help detect loose fasteners and/or damaged forward engine mount hanger 
fittings and bulkhead.   Loose fasteners and/or damaged or cracked forward engine mount hanger fittings could 
lead to failure of the hanger fitting and bulkhead and the subsequent separation of the engine.
Three operators have reported many instances where the fasteners common to the forward engine mount 
hanger fitting and strut forward bulkhead have been found loose. There was also one report of hanger fitting 
damage. In the reports where loose fasteners were found, the fasteners were removed, the holes inspected and 
repaired and new fasteners installed. The damaged hanger fitting was replaced.   
Hanger fitting looseness has been attributed to loose fasteners common to the strut forward engine mount 
bulkhead. These fasteners were replaced on airplanes during incorporation of Boeing service bulletin 747-
54A2159.   These fasteners may not have been fully torqued or the nuts may have bottomed out on the bolt 
threads prior to full clamp-up or  "shanked", during fastener torque. In addition, certain tolerance build-up 
conditions during production at Boeing may also cause the nuts to 'shank' during installation. This condition 
could lead to the loss of fastener clamp up capability, hanger fitting movement and reduced attachment 
capability. 
Inspection and replacement of these fasteners will maintain clamp-up of the fasteners and help to prevent 
damage to the forward engine mount hanger fittings and bulkhead. 
After release of the original issue of this service bulletin, several operators have reported finding under-torqued 
or loose fasteners after accomplishment of Part 6 Terminating Action.  In addition, one operator reported finding 
an approximately 1.5 inch crack in the bulkhead chord adjacent to the upper Group B fastener on a no. 2 strut 
with approximately 20,050 flight-cycles and 110,000 flight-hours.  Further investigation revealed that the back-
up angle inside the strut adjacent to the crack had fractured.

### Page 8

August 31, 2000
Revision 2:  July 09, 2009 747-54A2203
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 8 of 102
BOEING SERVICE BULLETIN 747-54A2203
ALERT                                                                                                    ALERT
 
 
Boeing Service Related Problem (SRP) 747-SRP-54-0068 is related to this service bulletin.
Boeing Service Related Problem (SRP) 747OP-SRP-54-0114 is related to this service bulletin.
ACTION
Do a DET and torque check of the forward engine mount fittings and the adjacent support structure on the 
inboard and outboard struts for loose fasteners and/or damage to the hanger fitting and bulkhead.   Repair or 
replace damaged hanger fittings. Contact The Boeing Company for repair instructions for damage found on 
adjacent support structure.
Do a High Frequency Eddy Current (HFEC) Inspection or Fluorescent Penetrant Inspection (FPI) of the forward 
engine mount bulkhead chords for cracks. Do a DET and HFEC inspection of the internal angle and stiffener for 
cracks or fracture.
EFFECTIVITY
747 airplanes line numbers 1 through 814 powered by Pratt and Whitney JT9D -3 or -7 series engines, except 
JT9D-70's.
COMPLIANCE
The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to this service 
bulletin.  The Airworthiness Directive will make the compliance tasks and times given in this service bulletin 
mandatory.
Refer to paragraph 1.E., Compliance.
INDUSTRY SUPPORT INFORMATION
Boeing warranty remedies are available for airplanes in on which the Core Strut Mod Service Bulletin has been 
incorporated since May 26, 1997.    Please refer to Paragraph 2.B., Industry Support Information.
MANPOWER
Refer to Paragraph 1.G. Manpower.
MATERIAL INFORMATION
Operator Supplied Parts/Materials

### Page 9

August 31, 2000
Revision 2:  July 09, 2009 747-54A2203
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 9 of 102
BOEING SERVICE BULLETIN 747-54A2203
ALERT                                                                                                    ALERT
 
 
AND LOOSE FASTENERS
CHORDS FOR CRACKS
INSPECT BULKHEAD
AND/OR LOOSE FASTENERS
INSPECT FITTINGS FOR DAMAGE
INSPECT BULKHEAD
FOR CRACKS
INSPECT LOWER
WEB FOR CRACKS
INSPECT
CRACKS
CHANNEL FOR
BULKHEAD-TO-
FIREWALL
LOCATION
EPR TRANSMITTER
ACCESS DOOR
STRUT FWD
INSPECT INTERNAL ANGLE
AND STIFFENER FOR CRACKS 
OR FRACTURE (BOTH SIDES OF
STRUT).
FWD
FWD
V32231

### Page 10

August 31, 2000
Revision 2:  July 09, 2009 747-54A2203
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 10 of 102
BOEING SERVICE BULLETIN 747-54A2203
ALERT                                                                                                    ALERT
 
 
BLANK PAGE

### Page 11

August 31, 2000
Revision 2:  July 09, 2009 747-54A2203
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 11 of 102
 
 
ALERT ALERT
Commercial
Airplane
Group 747
ALERTALERT
Service Bulletin
Number: 747-54A2203
Date: August 31, 2000
Revision 2: July 09, 2009
ATA System: 5441
SUBJECT: NACELLES/PYLONS - Strut Forward Engine Mount - Inspection/Rework
THIS BULLETIN IS SENT TO THE OPERATORS OF RECORD OF THE AIRPLANES SHOWN IN 
PARAGRAPH 1.A., EFFECTIVITY.  IF AN AIRPLANE HAS BEEN LEASED OR SOLD, SEND THIS SERVICE 
BULLETIN TO THE NEW OPERATOR.  IF APPLICABLE SPARES HAVE BEEN SOLD, SEND THIS SERVICE 
BULLETIN TO THE NEW OWNER.
1. PLANNING INFORMATION
A. Effectivity
1. Airplanes
Refer to Service Bulletin Index Document D6-30300, Part 3 for Airplane Variable Number, Line 
Number, and Serial Number data.
This service bulletin is for the airplanes shown below.
Airplane models:
747-100 747-100B 747-100B SUD 747-200B
747-200C 747-200F 747-300 747SP
747SR
IDENTIFICATION BY CUSTOMER, CUSTOMER CODE, GROUP AND VARIABLE NUMBER
AERO CONTROLS  (AEO)
1 RA722–RA723
AEROLINEAS ARGENTINAS  (ARG)
1 RD122–RD127
AFRICA UNITED HOLDING CO.  (UHD)
1 RB010 RD513
GROUP CONFIGURATION DESCRIPTION
1 - 747 airplanes with JT9D-3/7 struts (except 
JT9D-70).

### Page 12

August 31, 2000
Revision 2:  July 09, 2009 747-54A2203
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 12 of 102
BOEING SERVICE BULLETIN 747-54A2203
ALERT                                                                                                    ALERT
 
 
AFX  (AXL)
1 RD201
AGES AIRCRAFT SALES & LEASING  (AGJ)
1R B 0 0 4
AIR ATLANTA ICELANDIC  (AID)
1 RB421 RS211 RS233 RS235
RS237
AIR CANADA  (ACN)
1 RA749–RA750 RD531
AIR CHINA  (BEJ)
1 RD782–RD783 RR451
AIR GULF FALCON  (GFG)
1R A 5 3 5 R A 5 3 7
AIR INDIA  (AIN)
1R A 7 2 9 R A 7 3 1
ALBARAKA  (AAB)
1R B 1 0 2
AMERICAN AIRLINES  (AAL)
1R A 2 6 6
ARKIA ISRAELI AIRLINES  (ARK)
1R A 2 5 3
BAHRAIN ROYAL FLIGHT  (BHR)
1 RG009
BANC OF AMERICA LEASING  (SBC)
1 RA106 RD001–RD002
BOEING AIRCRAFT HOLDING CO.  (BHC)
1R J 1 3 2
C.I.T. LEASING CORPORATION  (TCI)
1 RB011 RD047
CAPITAL ASSET MANAGEMENT  (CPG)
1 RD053
CARGAIR  (CGL)
1 RD203
CORSAIR  (COR)
1 RS239–RS240

### Page 13

August 31, 2000
Revision 2:  July 09, 2009 747-54A2203
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 13 of 102
BOEING SERVICE BULLETIN 747-54A2203
ALERT                                                                                                    ALERT
 
 
DRAGONAIR  (DRG)
1 RR522 RS741 RS743 RS771
DUBAI AIR WING  (DAW)
1 RD622
EL AL ISRAEL AIRLINES  (ELA)
1 RD442 RJ152 RR225–RR226
EVERGREEN A/C SALES & LEASING  (EVG)
1 RA371 RD056–RD057 RD241 RD243
RD254–RD255 RD257
EVERGREEN INTERNATIONAL A/L  (EVR)
1 RA028 RA631 RA633 RB604
RB607 RD004 RD041–RD043 RJ131
RJ133
EXPORT RESTRICTED AIRPLANES  (YWV)
1 RA101–RA103 RA112 RA161–RA163 RB711
RD681–RD682 RG101–RG104 RG141–RG142 RG171
RR001–RR004
FINOVA  (GRB)
1 RA651
FIRST CHICAGO CORP.  (FCC)
1 RD260
GE  (GEC)
1 RA016
GECAS  (GEF)
1 RA007 RA013 RA027
GENERIC CUSTOMER/SUPPLIER  (XXX)
1 RD055 RD104 RD261–RD262
GLOBAL AIR LEASING  (GAO)
1 RG164
GLOBAL PEACE INITIATIVE  (GPI)
1 RG174
GRACE CATHEDRAL INC.  (GCI)
1 RG193
HORTA  (HOB)
1 RG163
IBERIA AIRLINES  (IBE)
1 RD431–RD435

### Page 14

August 31, 2000
Revision 2:  July 09, 2009 747-54A2203
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 14 of 102
BOEING SERVICE BULLETIN 747-54A2203
ALERT                                                                                                    ALERT
 
 
INTERNATIONAL AIR LEASES  (IAL)
1R B 0 0 6
IRAQI AIRWAYS  (IRQ)
1 RG095 RG172 RJ301–RJ303
JAL INTERNATIONAL  (JAL)
1 RD227 RR265–RR266 RS251–RS254 RS256
RS259 RS265–RS267
JET AERO HOLDINGS  (JHD)
1 RG122
JOHNSON SPACE CENTER  (ZBR)
1R A 9 0 8 R B 6 0 1
JUMBO JET LEASING  (JJL)
1 RA526 RA532–RA534 RA539
KABO AIR  (KAB)
1 RA305 RA316 RA560 RB008
RD121
KALITTA AIR  (KAC)
1 RA401–RA402 RA524 RA546 RA548
RA635 RA913 RB605 RD054
RD082–RD083 RD221 RD224–RD225 RD571
RD621 RD623 RR261–RR262 RR361–RR362
RR501 RR521
KUWAIT AIRWAYS  (KUW)
1 RD202 RD204
LOGISTIC AIR, INC.  (LGA)
1 RA015 RA217 RA910 RB722–RB723
MK AIRLINES  (MKA)
1 RD441 RD781 RR022–RR023 RR336
RR504
NASA  (NAS)
1 RG091
NEA HOLDINGS, INC.  (NEA)
1 RB001 RD045–RD046
NORTHWEST AIRLINES  (NWA)
1 RD242 RD251–RD253 RD258–RD259 RD301–RD302
RR005 RR341–RR342 RR344–RR345 RR431–RR432
RR503 RR566
OMAN ROYAL FLIGHT  (RFO)
1 RG161

### Page 15

August 31, 2000
Revision 2:  July 09, 2009 747-54A2203
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 15 of 102
BOEING SERVICE BULLETIN 747-54A2203
ALERT                                                                                                    ALERT
 
 
ORIENT THAI AIRLINES  (OTH)
1 RA528 RA540 RA543–RA544 RD222
RD516 RR264 RS001–RS002 RS257
RS292
PHUKET AIRLINES  (PHK)
1 RD421–RD424 RS238 RS241
PRATT & WHITNEY ENGINE SERVICE  (PWE)
1 RG213 RG222
ROYAL AIR MAROC  (RAM)
1 RD671
SAUDI ROYAL FLIGHT  (SRF)
1 RS699
SOUTH AFRICAN AIRWAYS  (SAA)
1 RG123 RG125 RS212 RS232
RS236
SOUTHERN AIR  (SOF)
1 RR024–RR025 RR267 RS786
TAAG (ANGOLA AIRLINES)  (ANG)
1 RS703 RS742
TESIS AVIATION ENTERPRISE  (TEV)
1 RA784
TRADEWINDS AIRLINES  (TWN)
1 RA726 RD052 RD426
TRANSAERO AIRLINES  (TRX)
1 RD226 RS255 RS258 RS263
RS268
TRANSATLANTIC INTL AIRLINES  (TIB)
1 RG173
UPS  (UPS)
1 RA026 RA029 RA033 RA902
RA912 RA915–RA916 RD051 RD058–RD059
RD593
WHIRLPOOL FINANCIAL CORP.  (ZZW)
1 RB005
WINGS WORLD WIDE  (WWW)
1 RG221
WORLDWIDE AIRCRAFT HOLDING CO.  (WAH)
1 RG008

### Page 16

August 31, 2000
Revision 2:  July 09, 2009 747-54A2203
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 16 of 102
BOEING SERVICE BULLETIN 747-54A2203
ALERT                                                                                                    ALERT
 
 
YEMENIA  (YEM)
1 RG162
YONA  (IOP)
1 RG191
IDENTIFICATION BY VARIABLE NUMBER
Variable  Group
RA001–RA034 1
RA101–RA115 1
RA161–RA164 1
RA201–RA203 1
RA216–RA217 1
RA245–RA246 1
RA251–RA266 1
RA301–RA318 1
RA351–RA360 1
RA369–RA373 1
RA401–RA418 1
RA501–RA502 1
RA521–RA528 1
RA532–RA548 1
RA551–RA552 1
RA559–RA561 1
RA581–RA582 1
RA585 1
RA601–RA602 1
RA631–RA635 1
RA651–RA652 1
RA671–RA677 1
RA701–RA702 1
RA721–RA731 1
RA741–RA745 1
RA749–RA750 1
RA761–RA762 1
RA781–RA784 1
RA901–RA916 1
RB001–RB012 1
RB041–RB044 1
RB071–RB075 1
RB101–RB102 1

### Page 17

August 31, 2000
Revision 2:  July 09, 2009 747-54A2203
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 17 of 102
BOEING SERVICE BULLETIN 747-54A2203
ALERT                                                                                                    ALERT
 
 
RB421 1
RB601–RB607 1
RB711 1
RB721–RB723 1
RD001–RD004 1
RD021–RD022 1
RD041–RD043 1
RD045–RD059 1
RD071–RD072 1
RD081–RD083 1
RD091–RD092 1
RD101–RD104 1
RD121–RD127 1
RD201–RD204 1
RD221–RD227 1
RD241–RD243 1
RD251–RD262 1
RD301–RD302 1
RD421–RD426 1
RD431–RD435 1
RD441–RD442 1
RD513–RD516 1
RD531 1
RD551 1
RD571 1
RD593 1
RD621–RD623 1
RD671 1
RD681–RD682 1
RD741–RD742 1
RD761 1
RD781–RD783 1
RE001 1
RG001–RG009 1
RG091 1
RG095 1
RG101–RG104 1
RG121–RG126 1
RG141–RG142 1
Variable  Group

### Page 18

August 31, 2000
Revision 2:  July 09, 2009 747-54A2203
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 18 of 102
BOEING SERVICE BULLETIN 747-54A2203
ALERT                                                                                                    ALERT
 
 
RG161–RG164 1
RG171–RG174 1
RG191–RG193 1
RG211–RG213 1
RG221–RG222 1
RJ131–RJ133 1
RJ151–RJ152 1
RJ301–RJ303 1
RR001–RR005 1
RR021–RR025 1
RR031 1
RR201 1
RR225–RR226 1
RR261–RR267 1
RR336 1
RR341–RR345 1
RR361–RR362 1
RR422 1
RR431–RR432 1
RR451 1
RR501–RR504 1
RR521–RR522 1
RR566 1
RS001–RS002 1
RS211–RS212 1
RS221–RS222 1
RS231–RS241 1
RS251–RS259 1
RS263 1
RS265–RS268 1
RS291–RS292 1
RS699 1
RS701–RS703 1
RS731–RS732 1
RS741–RS743 1
RS771 1
RS786 1
Variable  Group

### Page 19

August 31, 2000
Revision 2:  July 09, 2009 747-54A2203
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 19 of 102
BOEING SERVICE BULLETIN 747-54A2203
ALERT                                                                                                    ALERT
 
 
2. Spares Affected
None
B. Concurrent Requirements
None
C. Reason
This inspection, when completed, will help detect loose fasteners and/or damaged forward engine 
mount hanger fittings and bulkhead.   Loose fasteners and/or damaged or cracked forward engine 
mount hanger fittings could lead to failure of the hanger fitting and bulkhead and the subsequent 
separation of the engine.
Three operators have reported many instances where the fasteners common to the forward engine 
mount hanger fitting and strut forward bulkhead have been found loose. There was also one report of 
hanger fitting damage. In the reports where loose fasteners were found, the fasteners were removed, 
the holes inspected and repaired and new fasteners installed. The damaged hanger fitting was 
replaced.   
Hanger fitting looseness has been attributed to loose fasteners common to the strut forward engine 
mount bulkhead. These fasteners were replaced on airplanes during incorporation of Boeing service 
bulletin 747-54A2159.   These fasteners may not have been fully torqued or the nuts may have 
bottomed out on the bolt threads prior to full clamp-up or  "shanked", during fastener torque. In 
addition, certain tolerance build-up conditions during production at Boeing may also cause the nuts to 
'shank' during installation. This condition could lead to the loss of fastener clamp up capability, hanger 
fitting movement and reduced attachment capability. 
Inspection and replacement of these fasteners will maintain clamp-up of the fasteners and help to 
prevent damage to the forward engine mount hanger fittings and bulkhead. 
After release of the original issue of this service bulletin, several operators have reported finding 
under-torqued or loose fasteners after accomplishment of Part 6 Terminating Action.  In addition, one 
operator reported finding an approximately 1.5 inch crack in the bulkhead chord adjacent to the upper 
Group B fastener on a no. 2 strut with approximately 20,050 flight-cycles and 110,000 flight-hours.  
Further investigation revealed that the back-up angle inside the strut adjacent to the crack had 
fractured.
Revision 1 is sent to do the following:
1. Remove Terminating Action.
Several operators have found under-torqued or loose Group A and Group B fasteners after 
accomplishing Part 6 - Fastener Replacement.
2. Add Part 7 - HFEC Internal Angle Inspection and Part 8 - External Bulkhead Chord Inspection 
and DET Internal Angle Inspection.  Subsequent to the original issue of the service bulletin, an 
operator reported finding a crack in the bulkhead chord adjacent to the upper Group B fastener.  
Additional inspections revealed that the back-up angle inside the strut was fractured.

### Page 20

August 31, 2000
Revision 2:  July 09, 2009 747-54A2203
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 20 of 102
BOEING SERVICE BULLETIN 747-54A2203
ALERT                                                                                                    ALERT
 
 
3. Delete Part 3 - Torque Check.  The requirements have been moved to Part 2 - Detailed 
Inspection, Torque Stripe Inspection, and Torque Check.  This allows most inspection to be 
accomplished without removal of the internal strut components.
4. Require Part 6 - Fastener Replacement, Part 7 - HFEC Internal Angle Inspection, and Part 8 - 
External Bulkhead Chord Inspection and DET Internal Angle Inspection, be accomplished if 
Group B fastener no. 13 is found loose.  Removal of this fastener requires engine removal and 
access to the areas inside the strut.  Therefore, deferral of the procedures would not save 
significant manpower or downtime.
5. Revise Part 6 - Fastener Replacement to replace all fasteners and require a minimum 1/64 inch 
oversize of the hole if rework is required.
6. Revise the fastener code tables and fastener torque tables to be consistent for all figures.  Added 
the affected bolt locations and/or applicable fastener code to all tables.
7. Revise material requirements to reflect new standards.  Add BACN11Z()CK nuts as the preferred 
nut to NAS1805-() nuts.
The following sections were changed in Revision 1 as follows:
1. Summary - Added information on the new inspections and service history.  Added information to 
the Industry Support Statement section.
2. Planning - Added information on the new inspections and service history.  Moved the information 
which was in Figure 1 to Paragraph 1.E. Compliance.  Incorporated Notice (IN) 1 that removes 
airplanes RD044 and RR301 from the effectivity of this service bulletin. These airplanes where 
modified and no longer have JT9D pylons. Added Manpower estimates for Part 7 - HFEC Internal 
Angle Inspection and Part 8 - External Bulkhead Chord Inspection and DET Internal Angle 
Inspection.
3. Material - Added information to the Industry Support Statement section.  Revise the quantity of 
operator supplied parts.  Add BACN11Z()CK nuts as the preferred nut to NAS1805-() nuts.
4. Accomplishment Instructions - Added an option to perform inspections with leading edge flaps 
extended and locked.  Deleted Part 3 - Torque Check, the information is now included in Part 2 
- Detailed Inspection, Torque Stripe Inspection, and Torque Check.  Added Part 7 - HFEC 
Internal Angle Inspection and Part 8 - External Bulkhead Chord Inspection and DET Internal 
Angle Inspection.  Clarified subsequent action requirements if certain conditions are found in Part 
2 - Detailed Inspection, Torque Stripe Inspection, and Torque Check.  Updated the format to the 
latest standard.  Revision bars were not included where there were format changes only.  Added 
option to re-install fastener if it is serviceable.
5. Figure 1 - Moved Information from the figure to paragraph 1.E., Compliance. 
6. Figure 2 - Added Group A primary and secondary fastener locations to hanger fitting, and clarified 
inspection instructions.  Added reference that a borescope is recommended to accomplish some 
of the inspections.

### Page 21

August 31, 2000
Revision 2:  July 09, 2009 747-54A2203
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 21 of 102
BOEING SERVICE BULLETIN 747-54A2203
ALERT                                                                                                    ALERT
 
 
7. Figure 3 - Revised figure to show torque stripe inspection as a method for inspecting for under-
torqued or loose fasteners.  Revised the instructions for inspecting fasteners without torque 
stripes to eliminate the need for aft side access to verify the torque of the fasteners.  Torque is 
applied only to the fastener head or nut accessible from the forward side.  Revised the torque 
values for determining if a fastener is under-torqued or loose.  Added instructions to add torque 
stripe to fasteners to facilitate future repeat Part 2 - Detailed Inspection, Torque Stripe Inspection, 
and Torque Checks.
8. Figure 4 - Revised figure to require all fasteners be re-tightened when an under-torqued or loose 
fastener is found.  Require only the loose fasteners be removed and the holes be  inspected when  
loose fasteners are found.  Added step to add torque stripe to fasteners to facilitate future repeat 
Part 2 - Detailed Inspection, Torque Stripe Inspection, and Torque Checks.  Add BACN11Z()CK 
nuts as the preferred nut to NAS1805-() nuts.
9. Figure 5 - Deleted this figure as Part 3 - Torque Check has been deleted.
10. Figure 6 - Added circle note call outs to both hanger fittings, clarified hole edge margins, and hole 
chamfers.  Added step to add torque stripe to fasteners to facilitate future repeat Part 2 - Detailed 
Inspection, Torque Stripe Inspection, and Torque Checks.  Add BACN11Z()CK nuts as the 
preferred nut to NAS1805-() nuts.
11. Figure 7 - Added circle note call outs to both hanger fittings.  Clarified drill / ream instructions.  
Added step to add torque stripe to fasteners to facilitate future repeat Part 2 - Detailed Inspection, 
Torque Stripe Inspection, and Torque Checks.  Add BACN11Z()CK nuts as the preferred nut to 
NAS1805-() nuts.
12. Figure 8 - Added circle note call outs to both hanger fittings, clarified hole edge margins, and hole 
chamfers.  Add BACN11Z()CK nuts as the preferred nut to NAS1805-() nuts.
13. Figure 9 - Added new figure to do an inspection of the forward engine mount bulkhead chord for 
cracks and a DET of the internal angle for fracture.
14. Figure 10 - Added new figure to inspect the internal angle and stiffener.  Subsequent to the 
release of the original issue of this service bulletin an operator reported finding a fractured 
internal angle.
Revision 2 is sent to do the following:
1. Add instructions for airplanes which were not affected by the Original Issue or Revision 1 of the 
service bulletin.  The inspections and fastener replacement in the Original Issue of this service 
bulletin were not required if two washers were installed under the nuts of the Group A fasteners 
or the pin protrusion was per the SRM.  When terminating action was removed from the service 
bulletin in revision 1, some operators reported that the fasteners types specified in Revision 1 did 
not match the fasteners on the airplane.  For airplanes not affected by the Original Issue, all of 
the Group B fasteners, except fastener no. 13,  would have hi-lok bolts and collars installed and 
not the fasteners specified in Revision 1, as these airplanes were not required to replace the 
fasteners in the Original Issue.  The Group A and B fasteners on airplanes not affected by the 
Original Issue should be removed and replaced with the fasteners given in Revision 1 or Revision 
2. 
2. Clarify the requirements in the torque stripe not applied and no under-torqued or loose fastener 
found action requirements by reordering the steps.

### Page 22

August 31, 2000
Revision 2:  July 09, 2009 747-54A2203
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 22 of 102
BOEING SERVICE BULLETIN 747-54A2203
ALERT                                                                                                    ALERT
 
 
3. Added option to support engine weight instead of engine removal in Part 7 - HFEC Internal Angle 
Inspection. 
The following sections were changed in Revision 2 as follows:
1. Planning - Paragraph 1.E., Compliance.  Add requirements for airplanes not affected by the 
original release: See note (h).  Revise order of steps in the torque stripe not applied and no under-
torqued or loose fastener found action requirements.
2. Accomplishment Instructions.  Revised Part 2 - Detailed Inspection, Torque Stripe Inspection, 
and Torque Check, Step 4., to add the requirements for airplanes which were not affected by the 
Original Issue or Revision 1 of this service bulletin and have hi-lok bolts and collars at all of  the 
Group B fastener locations, except fastener no. 13. 
3. Accomplishment Instructions. Revised Part 7 - HFEC Internal Angle Inspection to add option to 
support engine weight instead of engine removal. 
4. Figure 3.  Revised Table  2 - Torque Stripe not applied fastener looseness Inspection, Steps 7 
and 8, to add the requirements for airplanes which were not affected by the Original Issue or 
Revision 1 of this service bulletin and have hi-lok bolts and collars at all of  the Group B fastener 
locations, except fastener no. 13. 
Boeing Service Related Problem (SRP) 747-SRP-54-0068 is related to this service bulletin.
Boeing Service Related Problem (SRP) 747OP-SRP-54-0114 is related to this service bulletin.
D. Description
Do a detailed  inspection and torque check of the forward engine mount fittings and the adjacent 
support structure on the inboard and outboard struts for loose fasteners and/or damage to the hanger 
fitting and bulkhead. Repair or replace damaged hanger fittings. Contact The Boeing Company for 
repair instructions for damage found on adjacent support structure.
Do a High Frequency Eddy Current (HFEC) Inspection or Fluorescent Penetrant Inspection (FPI) of 
the forward engine mount bulkhead chords for cracks. Do a DET and HFEC inspection of the internal 
angle and stiffener for cracks or fracture.
Revision 1 - More work is necessary on airplanes changed as shown in the original issue of this 
service bulletin.  For all airplanes, including airplanes that have accomplished terminating action in 
accordance with Part 6 - Fastener Replacement or were not affected by the original issue of this 
service bulletin by having two washers installed on Group A fasteners during incorporation of service 
bulletin 747-54A2159, additional work is required to  accomplish the inspections in Part 2 - Detailed 
Inspection, Torque Stripe Inspection, and Torque Check and Part 8 - External Bulkhead Chord 
Inspection and DET Internal Angle Inspection or Part 2 - Detailed Inspection, Torque Stripe 
Inspection, and Torque Check and Part 7 - HFEC Internal Angle Inspection within 90 days after the 
date of Revision 1 of this service bulletin.  Repeat the inspections as given in paragraph 1.E., 
Compliance.  In addition, within 18 months after the date of Revision 1 of this service bulletin 
accomplish the following: 1) Part 7 - HFEC Internal Angle Inspection; 2) Part 8 - External Bulkhead 
Chord Inspection and DET Internal Angle Inspection; and 3) For struts where torque stripes were not 
previously applied to the fasteners, tighten all Group A and Group B fasteners.

### Page 23

August 31, 2000
Revision 2:  July 09, 2009 747-54A2203
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 23 of 102
BOEING SERVICE BULLETIN 747-54A2203
ALERT                                                                                                    ALERT
 
 
Revision 2 - More work is necessary on airplanes which were not affected by the Original Issue or 
Revision 1 of this service bulletin.  These airplanes have hi-lok bolts and collars at all of  the Group B 
fastener locations, except fastener no. 13.  These airplanes need to be inspected in accordance with 
Part 2 - Detailed Inspection, Torque Stripe Inspection, and Torque Check within 90 days after the date 
of Revision 2 of this service bulletin.  In addition, the fasteners on these airplanes need to be replaced 
in accordance with Part 6 - Fastener Replacement within 18 months after the date of Revision 2 of this 
service bulletin.
NOTE: Terminating Action was removed from the service bulletin in revision 1.

### Page 24

August 31, 2000
Revision 2:  July 09, 2009 747-54A2203
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 24 of 102
BOEING SERVICE BULLETIN 747-54A2203
ALERT                                                                                                    ALERT
 
 
E. Compliance
The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to 
this service bulletin.  The Airworthiness Directive will make the compliance tasks and times given in 
this service bulletin mandatory.
Table 1: Part 2 - Detailed Inspection, Torque Stripe Inspection, and Torque Check
Condition Action Compliance Time 
Repeat 
Interval 
(Not to 
Exceed)
All airplanes Do Part 2 - Detailed Inspection, Torque Stripe 
Inspection, and Torque Check.
Within 90 Days after the 
date of Revision 1 of this 
Service Bulletin. 
-
All airplanes (h) Do Part 2 - Detailed Inspection, Torque Stripe 
Inspection, and Torque Check (h).
Within 90 Days after the 
date of Revision 2 of this 
Service Bulletin. 
-
1) Torque stripe  
previously applied 
(g).
and
2) No indication of 
under-torqued and 
loose fasteners.
Repeat Part 2 - Detailed Inspection, Torque 
Stripe Inspection, and Torque Check.
- 18 months.
1) Torque stripe not 
previously applied.
and
2) No under-torqued 
and no loose 
fasteners Found.
1) Repeat Part 2 - Detailed Inspection, 
Torque Stripe Inspection, and Torque 
Check.
- 18 months.
and
2) Tighten all Group A fasteners and Group B 
fasteners  as given in Figure 4, Table 4.
Within 18 Months after 
the date of Revision 1 of 
this Service Bulletin. 
18 months.
and
3) Apply optional Torque Stripes as given in 
Part 2 - Detailed Inspection, Torque Stripe 
Inspection, and Torque Check.
Before further flight. -
1) Torque stripe not 
previously applied 
(h).
and
2) No under-torqued 
and no loose 
fasteners Found 
(h).
1) Do Part 6 - Fastener Replacement (h) Within 18 Months after 
the date of Revision 2 of 
this Service Bulletin. 
-
and
2) Do Part 2 - Detailed Inspection, Torque 
Stripe Inspection, and Torque Check (h).
Within 18 Months after 
the date of Part 6 - 
Fastener Replacement in  
this Service Bulletin. 
-

### Page 25

August 31, 2000
Revision 2:  July 09, 2009 747-54A2203
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 25 of 102
BOEING SERVICE BULLETIN 747-54A2203
ALERT                                                                                                    ALERT
 
 
Under-torqued or 
loose Group A 
fastener found
or
Under-torqued Group 
B Fastener found
1) Tighten all under-torqued or loose Group 
A fasteners and under-torqued Group B 
fasteners and apply optional torque stripes 
as given in Figure 4, Table 2 (a).
Before further flight. -
and
Repeat Part 2 - Detailed Inspection, 
Torque Stripe Inspection, and Torque 
Check (b).
- 6 months.
and
2) Do Part 6 - Fastener Replacement (c). Within 18 months after 
under-torqued or loose 
fastener was found.
-
and
Repeat Part 2 - Detailed Inspection, 
Torque Stripe Inspection, and Torque 
Check.
- 18 months.
Loose Group B 
Fastener found, 
except fastener no. 
13 (d).
1) Remove the loose fasteners, inspect the 
hole, install fastener, and apply optional 
torque stripes as given in Figure 4, Table 3 
(a).
Before further flight. -
and
Repeat Part 2 - Detailed Inspection and 
Torque Stripe Inspection (b).
- 6 months.
and
2) Do Part 6 - Fastener Replacement (c). Within 18 months after 
loose fastener was 
found.
-
and
Repeat Part 2 - Detailed Inspection and 
Torque Stripe Inspection
- 18 months.
Table 1: Part 2 - Detailed Inspection, Torque Stripe Inspection, and Torque Check
Condition Action Compliance Time 
Repeat 
Interval 
(Not to 
Exceed)

### Page 26

August 31, 2000
Revision 2:  July 09, 2009 747-54A2203
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 26 of 102
BOEING SERVICE BULLETIN 747-54A2203
ALERT                                                                                                    ALERT
 
 
Loose No. 13 Group 
B Fastener found (d).
1) Do Part 6 - Fastener Replacement (c). Before further flight. -
and
Do Part 7 - HFEC Internal Angle Inspection 
(e).
Before further flight. -
and
Do a HFEC or FPI of the bulkhead chord 
as given in Part 8 - External Bulkhead 
Inspection and DET Internal Angle 
Inspection (e).
Before further flight. -
and
2) Repeat Part 2 - Detailed Inspection, Torque 
Stripe Inspection, and Torque Check
- 18 months.
Loose hanger fitting 
found
Do Part 5 - Fitting Replacement or Part 6 - 
Fastener Replacement.
Before further flight. -
Any fretting damage 
to hanger fitting 
found
Do Part 4 - Fitting Rework or do Part 5 - Fitting 
Replacement.
Before further flight. -
Any crack found in 
bulkhead chord
Replace bulkhead chord (f). Before further flight. -
Any crack found in 
bulkhead
Contact The Boeing Company for additional 
instructions.
Before further flight. -
Any crack, damaged 
sealant or loose 
fasteners found in 
lower spar web 
forward bay
Contact The Boeing Company for additional 
instructions.
Before further flight. -
Any crack, damaged 
or loose fasteners 
found in the strut 
forward mount 
bulkhead channel
Contact The Boeing Company for additional 
instructions.
Before further flight. -
(a) If any Group A fastener is found loose or under-torqued, all Group A fasteners must be re-tightened. If 4 or 
more Group B fasteners were found under-torqued or loose, all Group B fasteners must be re-tightened.  
Re-tighten Group A "Secondary" Fasteners, if fastener was not torque striped.  Re-tighten Group B 
fasteners no.s 8 and 9, if fastener was not torque striped.  
(b) Repeat Part 2 - Detailed Inspection, Torque Stripe Inspection, and Torque Check at the reduced interval 
shown until Part 6 - Fastener Replacement is accomplished.
(c) If 2 or more Group A fastener were found loose or under torqued on any fitting, replace all Group A 
fasteners for the fitting.  If 4 or more Group B fasteners were found loose or under torqued on any fitting, 
replace all Group B fasteners for the fitting.
(d) Group B fasteners are numbered 5 through 13. The upper Group B fastener is fastener no. 13.
Table 1: Part 2 - Detailed Inspection, Torque Stripe Inspection, and Torque Check
Condition Action Compliance Time 
Repeat 
Interval 
(Not to 
Exceed)

### Page 27

August 31, 2000
Revision 2:  July 09, 2009 747-54A2203
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 27 of 102
BOEING SERVICE BULLETIN 747-54A2203
ALERT                                                                                                    ALERT
 
 
(e) See Table 2 for disposition of findings and repeat inspection interval.
(f) Contact The Boeing Company for additional instructions.
(g) Torque stripes applied in accordance with the original issue of this service bulletin or the Structural Repair 
Manual (SRM) are acceptable.
(h) Airplanes which were not affected by the Original Issue or Revision 1 of this service bulletin.
These airplanes have hi-lok bolts and collars at all of  the Group B fastener locations, except fastener no. 
13.  These airplanes need to be inspected in accordance with Part 2 - Detailed Inspection, Torque Stripe 
Inspection, and Torque Check within 90 days after the date of Revision 2 of this service bulletin.  In 
addition, the fasteners on these airplanes need to be replaced in accordance with Part 6 - Fastener 
Replacement within 18 months after the date of Revision 2 of this service bulletin.
Table 1: Part 2 - Detailed Inspection, Torque Stripe Inspection, and Torque Check
Condition Action Compliance Time 
Repeat 
Interval 
(Not to 
Exceed)

### Page 28

August 31, 2000
Revision 2:  July 09, 2009 747-54A2203
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 28 of 102
BOEING SERVICE BULLETIN 747-54A2203
ALERT                                                                                                    ALERT
 
 
Table 2: Part 8 - External Bulkhead Inspection and DET Internal Angle Inspection and Part 7 - HFEC Internal
Angle Inspection
Condition Action Compliance Time 
Repeat 
Interval (Not 
to Exceed)
All airplanes 1) Do a High Frequency Eddy Current (HFEC) 
Inspection or Florescent Penetrant Inspection 
(FPI) of the bulkhead chord and a Detailed 
Inspection (DET) of the internal angle as given 
in Part 8 - External Bulkhead Inspection and 
DET Internal Angle Inspection.
Within 90 days after 
the date of Revision 1 
of this Service Bulletin. 
6 months (a).
All airplanes 1) Do Part 7 - HFEC Internal Angle Inspection Within 18 months after 
the date of Revision 1 
of this Service Bulletin.
36 months.
and
2) Do a HFEC or FPI of the bulkhead chord and a 
Detailed Inspection (DET) of the internal angle 
as given in Part 8 - External Bulkhead 
Inspection and DET Internal Angle Inspection.
- 18 months 
(b).
Evidence of 
fractured internal 
angle
Do Part 7 - HFEC Internal Angle Inspection Before further flight. -
Fractured angle 
found
Replace internal angle (c) Before further flight. -
Any crack found 
in bulkhead chord
Replace bulkhead chord (c) Before further flight. -
Any crack found 
in internal angle
Replace internal angle (c) Before further flight. -
Any crack found 
in stiffener 
Repair or replace stiffener (c) Before further flight. -
Fractured 
stiffener found
Repair or replace stiffener (c) Before further flight. -
(a)  Use this repeat interval for the Part 8 - External Bulkhead Inspection and DET Internal Angle Inspection 
until Part 7 - HFEC Internal Angle Inspection is accomplished.
(b)  Use this repeat interval for the Part 8 - External Bulkhead Inspection and DET Internal Angle Inspection 
after the initial Part 7 - HFEC Internal Angle Inspection is accomplished.
(c)  Contact The Boeing Company for additional instructions.

### Page 29

August 31, 2000
Revision 2:  July 09, 2009 747-54A2203
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 29 of 102
BOEING SERVICE BULLETIN 747-54A2203
ALERT                                                                                                    ALERT
 
 
F. Approval
This service bulletin was examined by the Federal Aviation Administration (FAA). The changes 
specified in this service bulletin comply with the applicable regulations and are FAA approved, as well 
as European Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/
JAA approved airplanes listed in the service bulletin effectivity.  This service bulletin and its approval 
were based on the airplane in its original Boeing delivery configuration or as modified by other 
approved Boeing changes.
If an airplane has a non-Boeing modification or repair that affects a component or system also affected 
by this service bulletin, the operator is responsible for obtaining appropriate regulatory agency 
approval before incorporating this service bulletin.
G. Manpower
The table below shows an estimate of the man-hours necessary to do this inspection for each engine. 
This estimate is for direct labor only, done by an experienced crew. Adjust the estimate with operator 
man-hour data if necessary. The estimate does not include lost time. These are some examples of 
lost time:
— Time to adjust to the workplace
— Time to schedule the work
— Time to examine the work
— Time to cure the materials
— Time to make the parts
— Time to find the tools.
Part 1 - Access and Part 9 - Restoration
Part 2 - Detailed Inspection, Torque Stripe Inspection, and Torque Check
Part 3 - Torque Check and Chord Inspection
Deleted
Task Number of Persons Man-Hours Elapsed Time (Hours)
Open Access 2 4.0 2.0
Close Access 2 5.5 2.75
TOTAL FOR EACH  ENGINE 9.5 4.75
Task Number of Persons Man-Hours Elapsed Time (Hours)
Inspect - DET 2 2.0 1.0
TOTAL FOR EACH  ENGINE 2.0 1.0

### Page 30

August 31, 2000
Revision 2:  July 09, 2009 747-54A2203
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 30 of 102
BOEING SERVICE BULLETIN 747-54A2203
ALERT                                                                                                    ALERT
 
 
Part 4 - Fitting Rework
Part 5 - Fitting Replacement
Part 6 - Fastener Replacement
Part 7 - HFEC Internal Angle Inspection
Part 8 - External Bulkhead Chord Inspection and DET Internal Angle Inspection
H. Weight and Balance Changes
None
I. Electrical Load Data
Not applicable
Task Number of Persons Man-Hours Elapsed Time (Hours)
Remove Engine 5 26 7
Rework Fitting 2 6 3
Install Engine 5 42 12
TOTAL FOR EACH  ENGINE 74 22
Task Number of Persons Man-Hours Elapsed Time (Hours)
Remove Engine 5 26 7
Replace Fitting 2 6 3
Install Engine 5 42 12
TOTAL FOR EACH  ENGINE 74 22
Task Number of Persons Man-Hours Elapsed Time (Hours)
Remove Engine 5 26 7
Rework Fitting 2 6 3
Install Engine 5 42 12
TOTAL FOR EACH  ENGINE 74 22
Task Number of Persons Man-Hours Elapsed Time (Hours)
Inspect - DET and HFEC 2 4 2
TOTAL FOR EACH  ENGINE 4 2
Task Number of Persons Man-Hours Elapsed Time (Hours)
Inspect - HFEC 2 2 1
TOTAL FOR EACH  ENGINE 2 1

### Page 31

August 31, 2000
Revision 2:  July 09, 2009 747-54A2203
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 31 of 102
BOEING SERVICE BULLETIN 747-54A2203
ALERT                                                                                                    ALERT
 
 
J. References
1. Existing Data:
a. 747-100/200/300 Aircraft Maintenance Manual (AMM)  12-09-09, 27-81-00, 30-21-06, 
54-32-00, 71-00-02, 71-11-00, 71-11-10, 71-21-01, 77-11-02, 78-31-00
b. 747-100/200/300 Structural Repair Manual (SRM)  51-10-01, 51-30-01, 51-30-02
c. 747-SP Structural Repair Manual (SRM)  51-10-01, 51-30-01, 51-30-02
d. 747 Non-Destructive Testing (NDT) Manual,  Part 6, 51-00-00
e. Boeing Service Bulletin 747-54A2159, "Nacelles/Pylons - JT9D (Except JT9D-70) Powered 
Airplanes - Nacelle Strut and Wing Structure Modification"
f. Service Related Problem (SRP) 747-SRP-54-0068
g. Service Related Problem (SRP) 747-SRP-54-0114
h. Standard Overhaul Practices Manual (SOPM)  20-10-03, 20-20-02, 20-30-03
2. Data supplied with this Service Bulletin:
None
3. Installation Drawings Used in the Preparation of this Service Bulletin:
This drawing was used to prepare this service bulletin. This drawing is not necessary to make the 
specified changes, and is not supplied with this service bulletin. This drawing may not be 
applicable to all airplane configurations or operators.
K. Publications Affected
L. Interchangeability and Intermixability of Parts
None
Drawing Number Title
65B90316 Bulkhead Installation - Forward Engine
Mount, Station 128.18, NAC Strut
Publication Chapter-Section
747 Illustrated Parts Catalog 54-41

### Page 32

August 31, 2000
Revision 2:  July 09, 2009 747-54A2203
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 32 of 102
BOEING SERVICE BULLETIN 747-54A2203
ALERT                                                                                                    ALERT
 
 
BLANK PAGE

### Page 33

August 31, 2000
Revision 2:  July 09, 2009 747-54A2203
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 33 of 102
BOEING SERVICE BULLETIN 747-54A2203
ALERT                                                                                                    ALERT
 
 
2. MATERIAL INFORMATION
A. Material - Price and Availability
The operator can supply the parts and materials shown in Paragraph 2.C., Parts Necessary For Each 
Airplane. As an alternative, operators can purchase the parts from Boeing Spares. This service 
bulletin does not show the Boeing price and supply data.
B. Industry Support Information
Boeing warranty remedies are available for 747 airplanes on which the core strut mod service bulletin 
has been incorporated since May 26, 1997. For inspection man-hour reimbursement for airplanes in 
warranty as of that date, send a warranty claim to Boeing Commercial Airplanes Group - Warranties. 
If the condition described in this service bulletin is found during the inspection for airplanes in warranty 
as of that date and additional man-hours and kits, parts, and/or special tools are required, send a 
warranty claim to Boeing Commercial Airplanes Group - Warranties. Please refer to this service 
bulletin number and reference the airplane variable numbers in your purchase order.
C. Parts Necessary For Each Airplane
1. Kits/Parts:
None
2. Parts and Materials Supplied by the Operator:
Parts listed are quantity required per strut.
QTY Part Number / Specification Name
1 65B90335-7 Fitting
1 65B90335-8 Fitting
12 65B90316-7 Filler (d)
4 BACB30FP8A6U Bolt (a)
4 BACB30KK8A6U Bolt (a)
12 BACB30LE4K8X
(BACB30US4K8X optional)
Bolt (a)
12 BACB30LE4K8Y
(BACB30US4K8Y optional)
Bolt (a)
2 BACB30LE5K18X
(BACB30US5K18X optional)
Bolt (a)
2 BACB30LE5K18Y
(BACB30US5K18Y optional)
Bolt (a)
4 BACB30MB12A8U Bolt (a)
4 BACB30MC10A8U Bolt (a)
4 BACB30MD10A8U Bolt (a)
12 BACN10HR4CS Nut
2 BACN10HR5CS Nut
2 BACS40R013U013 Shim

### Page 34

August 31, 2000
Revision 2:  July 09, 2009 747-54A2203
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 34 of 102
BOEING SERVICE BULLETIN 747-54A2203
ALERT                                                                                                    ALERT
 
 
3. Parts Modified and Reidentified:
None
12 BACW10BP41ACU Washer
20 BACW10BP41APU Washer
12 BACW10BP42ACU Washer
20 BACW10BP42APU Washer
2 BACW10BP51ACU Washer
12 BACW10BP51APU Washer
2 BACW10BP52ACU Washer
12 BACW10BP52APU Washer
8 BACW10BP61APU Washer
8 BACW10BP62APU Washer
8 BACW10BP6APU Washer
8 BACW10BP7APU Washer
4 BACN11Z4CK (NAS1805-4 opt.) Nut
4 BACN11Z5CK (NAS1805-5 opt.) Nut
8 BACN11Z6CK (NAS1805-6 opt.) Nut
4 BACN11Z7CK (NAS1805-7 opt.) Nut
4 NAS6706U8X (BACB30LM6U8X
opt.)
Bolt (a)
4 NAS6706U8Y (BACB30LM6U8Y
opt.)
Bolt (a)
1 pint BMS 5-63 Sealant (b)
2 ounces F-925 Torque Seal, Marking Lacquer
(c)
(a) An alternate grip fastener may be used in place of those specified, provid-
ed no more than three washers (BACW10BP*) are used per fastener in-
stallation.  Three under the nut.
(b) See the Qualified Products List at the end of the Boeing Material Specifi-
cation (BMS) for supplier data.
(c) Torque Seal, Anti-Sabotage Inspector's Lacquer (M23.15.7.0)
Organic Products Company
1963 East Irving Blvd. P.O. Box 428
Irving, Texas 75060-4555
(d) 0.063 X 0.7 X 0.8 inch CRES 301 or 304 Sheet, ANL, per MIL-S-5059 or
CRES 321 or 347 Sheet, ANL, per MIL-S-6721
QTY Part Number / Specification Name

### Page 35

August 31, 2000
Revision 2:  July 09, 2009 747-54A2203
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 35 of 102
BOEING SERVICE BULLETIN 747-54A2203
ALERT                                                                                                    ALERT
 
 
4. Parts Removed and Not Replaced:
None
D. Parts Necessary to Change Spares
None
E. Special Tooling - Price and Availability
None
F. Special Tooling Necessary to do this Service Bulletin
No special tools or equipment are necessary to do the change in this service bulletin. But, 
maintenance and overhaul tools in the manuals given in Paragraph 1.J., References, can be 
necessary. Examine operator tool supply to make sure all necessary tools are available.

### Page 36

August 31, 2000
Revision 2:  July 09, 2009 747-54A2203
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 36 of 102
BOEING SERVICE BULLETIN 747-54A2203
ALERT                                                                                                    ALERT
 
 
BLANK PAGE

### Page 37

August 31, 2000
Revision 2:  July 09, 2009 747-54A2203
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 37 of 102
BOEING SERVICE BULLETIN 747-54A2203
ALERT                                                                                                    ALERT
 
 
3. ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL INFORMATION
CAUTION: KEEP THE WORK AREA, WIRES AND ELECTRICAL BUNDLES CLEAN OF METAL
PARTICLES OR CONTAMINATION WHEN YOU USE TOOLS. UNWANTED
MATERIAL, METAL PARTICLES OR CONTAMINATION CAUGHT IN WIRE BUNDLES
CAN CAUSE DAMAGE TO THE BUNDLES. DAMAGED WIRE BUNDLES CAN CAUSE
SPARKS OR OTHER ELECTRICAL DAMAGE. 
NOTE:
1. The paragraphs identified with a letter give the general work instructions and the 
necessary tests. The instructions identified with numbers on the figures give the 
recommended sequence of steps.
2. Unless shown differently, these dimensions and tolerances are used:
— Linear dimensions are in inches
— Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus or 
minus 0.03 inch
— Tolerance on rivet and bolt edge margin is plus or minus 0.05 inch
— Angular tolerance is plus or minus 2 degrees
— Hole dimensions for standard solid rivets are given in 747 Structural Repair 
Manual, Chapter 51
— Torque limits to tighten nuts and bolts are given in 747 Structural Repair Manual, 
Chapter 51.
3. Obey all of the warnings and cautions given in the specified manual sections. 
4. A Detailed Inspection (DET) is defined as: An intensive examination of a specific item, 
installation, or assembly to detect damage, failure, or irregularity. Available lighting is 
normally supplemented with a direct source of good lighting at an intensity deemed 
appropriate. Inspection aids such as mirrors magnifying lenses, etc. may be necessary.  
Surface cleaning and elaborate procedures may be required.
5. These work instructions refer to procedures included on other Boeing documents. When 
the words "refer to" are used and the operator has an accepted alternative procedure, 
the accepted alternative procedure can be used. When the words "as given in" are 
included in the instruction, the procedure in the Boeing document must be used.
6. If a fastener is removed, the bolt can be re-installed if it is still serviceable. Replace the 
nut with a new nut which meet the break-away and run-on torque requirements. 
B. WORK INSTRUCTIONS
Part 1 - Access
WARNING: LEADING EDGE FLAPS ARE FAST ACTING. LOCKS SHOULD BE INSTALLED TO
PREVENT POSSIBLE INJURY DUE TO INADVERTENT OPERATION OF FLAPS.
1. Retract the leading edge flaps if they are extended. Refer to 747-100/200/300 AMM 27-81-00 as 
an accepted procedure.

### Page 38

August 31, 2000
Revision 2:  July 09, 2009 747-54A2203
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 38 of 102
BOEING SERVICE BULLETIN 747-54A2203
ALERT                                                                                                    ALERT
 
 
NOTE: The leading edge flaps may be extended and leading edge locks installed. Refer to
747-100/200/300 AMM 27-81-00 as an accepted procedure.
2. Install leading edge locking devices. Refer to 747-100/200/300 AMM 27-81-00 as an accepted 
procedure.
3. Deactivate the thrust reversers. Refer to 747-100/200/300 AMM 78-31-00 as an accepted 
procedure.
4. Remove and keep each strut forward fairing 451, 461, 471, or 481. Refer to 747-100/200/300 
AMM 12-09-09 as an accepted procedure.
5. Open strut access doors 452AL, 462AL, 472AL, or 482AL. Refer to 747-100/200/300 AMM 
12-09-09 and 747-100/200/300 AMM 54-32-00 as accepted procedures. 
6. If additional access is required to do Part 2 - Detailed Inspection, Torque Stripe Inspection, and 
Torque Check, Part 4 - Fitting Rework, Part 5 - Fitting Replacement and/or Part 6 - Fastener 
Replacement.  Remove and keep the slot seal fairings. Refer to 747-100/200/300 AMM 71-11-10 
as an accepted procedure.
Part 2 - Detailed Inspection, Torque Stripe Inspection, and Torque Check
1. Provide access to inspection area as given in Part 1 - Access, if not previously done.
2. Do a DET of the forward engine mount hanger fittings and surrounding support structure, external 
to the strut, for cracks and/or fretting damage as given in Figure 2.
a. If a loose hanger fitting is found, do Part 5 - Fitting Replacement or Part 6 - Fastener 
Replacement within the compliance time given in paragraph 1.E., Compliance.
b. If any fretting damage to hanger fitting is found, do Part 4 - Fitting Rework or do Part 5 - 
Fitting Replacement within the compliance time given in paragraph 1.E., Compliance.
c. If any crack found in bulkhead chord, Replace bulkhead chord within the compliance time 
given in paragraph 1.E., Compliance.  Contact The Boeing Company for additional 
instructions
d. If any crack found in bulkhead, contact The Boeing Company for additional instructions 
within the compliance time given in paragraph 1.E., Compliance.
e. If any crack, damaged sealant or loose fasteners found in lower spar web forward bay, 
contact The Boeing Company for additional instructions within the compliance time given in 
paragraph 1.E., Compliance.
f. If any crack, damaged or loose fasteners found in the strut forward mount bulkhead channel, 
contact The Boeing Company for additional instructions within the compliance time given in 
paragraph 1.E., Compliance.
3. Do a DET of the torque stripes, if previously applied, for evidence of under-torqued or loose 
fasteners as given in Table 1 Figure 3, Torque Stripe Inspection.

### Page 39

August 31, 2000
Revision 2:  July 09, 2009 747-54A2203
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 39 of 102
BOEING SERVICE BULLETIN 747-54A2203
ALERT                                                                                                    ALERT
 
 
a. If no evidence of under-torqued or loose fasteners is found, repeat Part 2 - Detailed 
Inspection, Torque Stripe Inspection, and Torque Check at the intervals given in paragraph 
1.E., Compliance. 
b. If evidence of under-torqued or loose Group A fasteners or under-torqued Group B fasteners 
is found, tighten all loose or under-torqued fasteners as given in Figure 4, Table 2 within the 
compliance time given in paragraph 1.E., Compliance.  Repeat Part 2 - Detailed Inspection, 
Torque Stripe Inspection, and Torque Check at the intervals given in paragraph 1.E., 
Compliance until Part 6 - Fastener Replacement is accomplished.  Do Part 6 - Fastener 
Replacement within the compliance time given in paragraph 1.E., Compliance.  Repeat Part 
2 - Detailed Inspection, Torque Stripe Inspection, and Torque Check at the intervals given 
in paragraph 1.E., Compliance.
NOTE:
1. If any Group A fastener was found loose or under-torqued, all Group A 
fasteners must be re-tightened.
2. If any Group B fastener is found under-torqued, the under-torqued fastener 
must be re-tightened.  If 4 or more Group B fasteners were found under-
torqued or loose, re-tighten all Group B fasteners.
c. If evidence of loose Group B fasteners is found, except fastener no.13, remove all loose 
fasteners, inspect the holes, and install fasteners as given in Table 3 in Figure 4 within the 
compliance time given in paragraph 1.E., Compliance.  Repeat Part 2 - Detailed Inspection, 
Torque Stripe Inspection, and Torque Check at the intervals given in paragraph 1.E., 
Compliance until Part 6 - Fastener Replacement is accomplished.  Do Part 6 - Fastener 
Replacement within the compliance time given in paragraph 1.E., Compliance.  Repeat Part 
2 - Detailed Inspection, Torque Stripe Inspection, and Torque Check at the intervals given 
in paragraph 1.E., Compliance.
d. If evidence of loose no. 13 Group B fastener is found, do Part 6 - Fastener Replacement 
within the compliance time given in paragraph 1.E., Compliance.  Do Part 7 - HFEC Internal 
Angle Inspection and Part 8 - External Bulkhead Chord Inspection and DET Internal Angle 
Inspection within the compliance time given in paragraph 1.E., Compliance.  Repeat Part 2 
- Detailed Inspection, Torque Stripe Inspection, and Torque Check at the intervals given in 
paragraph 1.E., Compliance.

### Page 40

August 31, 2000
Revision 2:  July 09, 2009 747-54A2203
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 40 of 102
BOEING SERVICE BULLETIN 747-54A2203
ALERT                                                                                                    ALERT
 
 
NOTE:
1. For Group A, primary bolts, a torque wrench adapter can be made from Snap-On 
tool Part Number GFRDH181. Reduce head depth at the wrench end to 0.19 inch 
thickness.
2. For additional access to the aft side of the hanger fitting fasteners, the EPR 
transmitter may be removed. Refer to 747-100/200/300 AMM 77-11-02 as an 
accepted procedure.
3. It may be necessary to remove the inlet cowl TAI duct from the front of the strut to 
do the torque check. Refer to 747-100/200/300 AMM 30-21-06 for duct removal as 
an accepted procedure.
4. If torque stripes were not previously applied, do a DET and torque check for evidence of under-
torqued or loose fasteners as given in Table 2 of Figure 3, Torque Stripe Not Applied Fastener 
Looseness Inspection.  For airplanes which were not affected by the Original Issue or Revision 
1 of this service bulletin and have hi-lok bolts and collars at all of  the Group B fastener locations,  
do a DET and torque check for evidence of under-torqued or loose fasteners as given in Table 2 
of Figure 3, Torque Stripe Not Applied Fastener Looseness Inspection.
a. For airplanes which were not affected by the Original Issue or Revision 1 of this service 
bulletin and have hi-lok bolts and collars at all of  the Group B fastener locations, do  Part 6 
- Fastener Replacement within the compliance time given in paragraph 1.E., Compliance.  
Repeat Part 2 - Detailed Inspection, Torque Stripe Inspection, and Torque Check at the 
intervals given in paragraph 1.E., Compliance.
b. If no evidence of under-torqued or loose fasteners is found, apply optional torque stripes as 
given in Figure 4, Table 2.  Repeat Part 2 - Detailed Inspection, Torque Stripe Inspection, 
and Torque Check at the intervals given in paragraph 1.E., Compliance.  Tighten all Group 
A fasteners and Group B fasteners as given in Figure 4, Table 4 within the threshold given 
in paragraph 1.E., Compliance and repeat the interval given in paragraph 1.E., Compliance.
c. If evidence of under-torqued or loose Group A fasteners or under-torqued Group B fasteners 
is found, tighten all loose or under-torqued fasteners as given in Figure 4, Table 2 within the 
compliance time given in paragraph 1.E., Compliance.  Repeat Part 2 - Detailed Inspection, 
Torque Stripe Inspection, and Torque Check at the intervals given in paragraph 1.E., 
Compliance until Part 6 - Fastener Replacement is accomplished.  Do Part 6 - Fastener 
Replacement within the compliance time given in paragraph 1.E., Compliance.  Repeat Part 
2 - Detailed Inspection, Torque Stripe Inspection, and Torque Check at the intervals given 
in paragraph 1.E., Compliance.

### Page 41

August 31, 2000
Revision 2:  July 09, 2009 747-54A2203
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 41 of 102
BOEING SERVICE BULLETIN 747-54A2203
ALERT                                                                                                    ALERT
 
 
NOTE:
1. If any Group A fastener was found loose or under-torqued, all Group A 
fasteners must be re-tightened.
2. If any Group B fastener is found under-torqued, the under-torqued fastener 
must be re-tightened.  If 4 or more Group B fasteners were found under-
torqued or loose, re-tighten all Group B fasteners.
3. Re-tighten Group A "Secondary" Fasteners, if fastener was not torque striped. 
4. Re-tighten Group B fasteners no.s 8 and 9, if fastener was not torque striped. 
d. If evidence of loose Group B fasteners is found, except fastener no.13, remove all loose 
fasteners, inspect the holes, and install fasteners as given in Table 3 in Figure 4 within the 
compliance time given in paragraph 1.E., Compliance.  Repeat Part 2 - Detailed Inspection, 
Torque Stripe Inspection, and Torque Check at the intervals given in paragraph 1.E., 
Compliance until Part 6 - Fastener Replacement is accomplished.  Do Part 6 - Fastener 
Replacement within the compliance time given in paragraph 1.E., Compliance.  Repeat Part 
2 - Detailed Inspection, Torque Stripe Inspection, and Torque Check at the intervals given 
in paragraph 1.E., Compliance.
e. If evidence of loose no. 13 Group B fastener is found, do Part 6 - Fastener Replacement 
within the compliance time given in paragraph 1.E., Compliance.  Do Part 7 - HFEC Internal 
Angle Inspection and Part 8 - External Bulkhead Chord Inspection and DET Internal Angle 
Inspection within the compliance time given in paragraph 1.E., Compliance.  Repeat Part 2 
- Detailed Inspection, Torque Stripe Inspection, and Torque Check at the intervals given in 
paragraph 1.E., Compliance.
5. Optional - Apply torque stripes to fasteners without torque stripes as given in Table 3 of Figure 
3, " Torque Stripe Application.
6. Close access as given in Part 9 - Restoration. 
Part 3 - Torque Check
1. This Part has been deleted.  The information has been moved to Part 2 - Detailed Inspection, 
Torque Stripe Inspection, and Torque Check 
Part 4 - Fitting Rework
1. Remove engine. Refer to 747-100/200/300 AMM 71-00-02 as an accepted procedure.
2. Remove forward upper engine mount. Refer to 747-100/200/300 AMM 71-21-01 as an accepted 
procedure.
3. Rework fitting as given in Figure 6.
4. Install forward upper engine mount. Refer to 747-100/200/300 AMM 71-21-01 as an accepted 
procedure. 
5. Install engine. Refer to 747-100/200/300 AMM 71-00-02 as an accepted procedure.

### Page 42

August 31, 2000
Revision 2:  July 09, 2009 747-54A2203
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 42 of 102
BOEING SERVICE BULLETIN 747-54A2203
ALERT                                                                                                    ALERT
 
 
Part 5 - Fitting Replacement
1. Remove engine. Refer to Refer to 747-100/200/300 AMM 71-00-02 as an accepted procedure.
2. Remove forward upper engine mount. Refer to 747-100/200/300 AMM 71-21-01 as an accepted 
procedure.
3. Replace the fitting as given in Figure 7.
4. Install the forward upper engine mount. Refer to 747-100/200/300 AMM 71-21-01 as an accepted 
procedure.
5. Install engine. Refer to 747-100/200/300 AMM 71-00-02 as an accepted procedure.
Part 6 - Fastener Replacement
1. If work per Part 4 - Fitting Rework or Part 5 - Fitting Replacement is being accomplished on any 
single fitting, no further action is required to be completed on that fitting by Part 6 - Fastener 
Replacement. Accomplish Part 6 - Fastener Replacement on the adjacent fitting, as required, as 
given below.
2. Remove engine. Refer to 747-100/200/300 AMM 71-00-02 as an accepted procedure.
NOTE: Engine removal is only required for replacement of Group A fasteners (fasteners no. 1
through 4) and Group B fastener no. 13.  Engine removal is not required for  replacement
of Group B fasteners 5 through 12, if only one fastener per fitting is replaced at a time.
3. Remove forward upper engine mount. Refer to 747-100/200/300 AMM 71-21-01 as an accepted 
procedure.
4. If any  fastener was found under-torqued or loose by previous Part 2 - Detailed Inspection, 
Torque Stripe Inspection, and Torque Check, remove and replace fasteners as given in Figure 8.
NOTE:
1. If 2 or more Group A fastener were found loose or under-torqued, all Group A 
fasteners must replaced.
2. If 4 or more Group B fasteners were found loose or under-torqued, all Group B 
fasteners must replaced.
5. Install the forward upper engine mount, if removed. Refer to 747-100/200/300 AMM 71-21-01 as 
an accepted procedure.
6. Install engine. Refer to 747-100/200/300 AMM 71-00-02 as an accepted procedure.
Part 7 - HFEC Internal Angle Inspection
1. Provide access to inspection area as given in Part 1 - Access, if not previously done.
2. Optional - Remove the EPR transmitter. Refer to 747-100/200/300 AMM 77-11-02 as an 
accepted procedure.

### Page 43

August 31, 2000
Revision 2:  July 09, 2009 747-54A2203
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 43 of 102
BOEING SERVICE BULLETIN 747-54A2203
ALERT                                                                                                    ALERT
 
 
3. Remove the engine. Refer to 747-100/200/300 AMM 71-00-02 as an accepted procedure.
As an option, support the engine weight as for engine removal.  The engine does not need to be 
removed.  The engine weight must be fully supported until Group B fastener no.13 fastener is 
installed and tightened.  Refer to 747-100/200/300 AMM 71-00-02 as an accepted procedure, 
except do not use the bootstrap (strut-mounted) components method.  The bootstrap (strut-
mounted) components method does not remove the load from the hanger fitting.
4. Do a DET and HFEC of the angles and upper stiffeners inside the strut as given in Figure 10.
a. If no crack or fracture is found, repeat Part 7 - HFEC Internal Angle Inspection and Part 8 - 
External Bulkhead Chord Inspection and DET Internal Angle Inspection at the interval given 
in paragraph 1.E., Compliance.
b. If any crack or fracture in the angle is found, replace angle within the compliance time given 
in paragraph 1.E., Compliance and repeat Part 7 - HFEC Internal Angle Inspection and Part 
8 - External Bulkhead Chord Inspection and DET Internal Angle Inspection at the interval 
given in paragraph 1.E., Compliance.  Contact The Boeing Company for additional 
instructions.
c. If any crack or fracture in the stiffener is found, repair or replace stiffener within the 
compliance time given in paragraph 1.E., Compliance and repeat Part 7 - HFEC Internal 
Angle Inspection and Part 8 - External Bulkhead Chord Inspection and DET Internal Angle 
Inspection at the interval given in paragraph 1.E., Compliance.  Contact The Boeing 
Company for additional instructions.
5. Install the engine. Refer to 747-100/200/300 AMM 71-00-02 as an accepted procedure.
6. Install the EPR transmitter, if removed. Refer to 747-100/200/300 AMM 77-11-02 as an accepted 
procedure.
7. Close access as given in Part 9 - Restoration. 
Part 8 - External Bulkhead Chord Inspection and DET Internal Angle Inspection
1. Provide access to inspection area as given in Part 1 - Access, if not previously done.
2. Do a High Frequency Eddy Current (HFEC) inspection or Florescent Penetrant Inspection (FPI), 
of the strut forward engine mount bulkhead chords for cracks, and a DET of the strut forward 
engine mount hanger fitting and strut forward engine mount bulkhead chord for evidence of a 
fractured internal angle as given in Figure 9. 
a. If no crack, or evidence of a fractured internal angle is found, repeat Part 8 - External 
Bulkhead Chord Inspection and DET Internal Angle Inspection at the interval given in 
paragraph 1.E., Compliance, until Part 7 - HFEC Internal Angle Inspection is accomplished.  
Accomplish Part 7 - HFEC Internal Angle Inspection within the compliance time given in 
paragraph 1.E., Compliance.  Repeat Part 7 - HFEC Internal Angle Inspection and Part 8 - 
External Bulkhead Chord Inspection and DET Internal Angle Inspection at the interval given 
in paragraph 1.E., Compliance.

### Page 44

August 31, 2000
Revision 2:  July 09, 2009 747-54A2203
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 44 of 102
BOEING SERVICE BULLETIN 747-54A2203
ALERT                                                                                                    ALERT
 
 
b. If no crack in the bulkhead chord is found, and evidence of internal angle fracture is found, 
do Part 7 - HFEC Internal Angle Inspection within the compliance time given in paragraph 
1.E., Compliance.  Repeat Part 7 - HFEC Internal Angle Inspection and Part 8 - External 
Bulkhead Chord Inspection and DET Internal Angle Inspection at the interval given in 
paragraph 1.E., Compliance.
c. If any crack in the bulkhead chord is found, replace bulkhead chord within the compliance 
time given in paragraph 1.E., Compliance and do Part 7 - HFEC Internal Angle Inspection 
within the compliance time given in paragraph 1.E., Compliance.  Contact The Boeing 
Company for additional instructions.  No cracks are allowed in the chord. Previously strop 
drilled cracks will require chord replacement.  Repeat Part 7 - HFEC Internal Angle 
Inspection and Part 8 - External Bulkhead Chord Inspection and DET Internal Angle 
Inspection at the interval given in paragraph 1.E., Compliance.
3. Do a DET of the internal angle for cracks or fracture as given in Figure 9 (not required if 
accomplishing Part 7 - HFEC Internal Angle Inspection).
a. If no crack or fracture of the internal angle is found, repeat internal angle inspection as given 
in Part 8 - External Bulkhead Chord Inspection and DET Internal Angle Inspection at the 
interval given in paragraph 1.E., Compliance, until Part 7 - HFEC Internal Angle Inspection 
is accomplished.  Accomplish Part 7 - HFEC Internal Angle Inspection within the compliance 
time given in paragraph 1.E., Compliance.  Repeat Part 7 - HFEC Internal Angle Inspection 
and Part 8 - External Bulkhead Chord Inspection and DET Internal Angle Inspection at the 
interval given in paragraph 1.E., Compliance
b. If any crack or fracture in the internal angle is found, replace angle within the compliance 
time given in paragraph 1.E., Compliance.  Contact The Boeing Company for additional 
instructions.  Repeat Part 7 - HFEC Internal Angle Inspection and Part 8 - External Bulkhead 
Chord Inspection and DET Internal Angle Inspection at the interval given in paragraph 1.E., 
Compliance.
4. Close access as given in Part 9 - Restoration. 
Part 9 - Restoration
1. Close strut access doors 452AL, 462AL, 472AL, or 482AL. Refer to 747-100/200/300 AMM 
12-09-09 and 747-100/200/300 AMM 54-32-00 as accepted procedures.
2. If EPR transmitter was removed for additional access, install EPR transmitter. Refer to 747-100/
200/300 AMM 77-11-02 as accepted procedures.
3. If inlet cowl TAI duct was removed, install the inlet cowl TAI duct. Refer to 747-100/200/300 AMM 
30-21-06 as an accepted procedure.
4. If slot seal was removed for additional access, install slot seal fairings. Refer to 747-100/200/300 
AMM 71-11-00 as an accepted procedure.
5. Install strut forward fairing 451, 461, 471, or 481. Refer to 747-100/200/300 AMM 12-09-09 as an 
accepted procedure.

### Page 45

August 31, 2000
Revision 2:  July 09, 2009 747-54A2203
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 45 of 102
BOEING SERVICE BULLETIN 747-54A2203
ALERT                                                                                                    ALERT
 
 
WARNING: LEADING EDGE FLAPS ARE FAST ACTING. LOCKS SHOULD BE INSTALLED TO
PREVENT POSSIBLE INJURY DUE TO INADVERTENT OPERATION OF FLAPS.
6. Remove leading edge locking devices. Refer to 747-100/200/300 AMM 27-81-00 as an accepted 
procedure.
7. Restore airplane to serviceable condition.

### Page 46

FIGURE 1: LOGIC DIAGRAM
August 31, 2000
Revision 2:  July 09, 2009 747-54A2203
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 46 of 102
BOEING SERVICE BULLETIN 747-54A2203
ALERT                                                                                                    ALERT
 
 
FIGURE  1:   LOGIC DIAGRAM
This Figure has been deleted. See Paragraph 1.E., Compliance, for inspection and maintenance alternatives.
THIS FIGURE DOES NOT HAVE AN ILLUSTRATION
V56655
(SHEET 1 OF 1)

### Page 47

FIGURE 2: FORWARD ENGINE MOUNT FITTING - DETAILED INSPECTION
August 31, 2000
Revision 2:  July 09, 2009 747-54A2203
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 47 of 102
BOEING SERVICE BULLETIN 747-54A2203
ALERT                                                                                                    ALERT
 
 
FIGURE  2:   FORWARD ENGINE MOUNT FITTING - DETAILED INSPECTION
(18 LOCATIONS)
(8 LOCATIONS)
STRUT FWD
ACCESS DOOR
A
A
FWD
2
4
BSEE
3
1
A
2
SEE A
B
3
6
5
V29928
(SHEET 1 OF 3)

### Page 48

FIGURE 2: FORWARD ENGINE MOUNT FITTING - DETAILED INSPECTION
August 31, 2000
Revision 2:  July 09, 2009 747-54A2203
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 48 of 102
BOEING SERVICE BULLETIN 747-54A2203
ALERT                                                                                                    ALERT
 
 
PRIMARY FASTENER
PRIMARY
FASTENER
FASTENER
SECONDARY
FASTENER
SECONDARY
SECONDARY
FASTENER
SECONDARY
FASTENER
PRIMARY
FASTENER
13
12
11
10
9
8
7
6
5
13
12
11
10
9
8
7
6
5
123 4123 4
FASTENER
PRIMARY
(9 LOCATIONS)(9 LOCATIONS)
'GROUP B'
'GROUP A''GROUP A'
'GROUP B'
1
1
1
1
1
1
1
1
1
11
A-A
UP1
V32261
(SHEET 2 OF 3)

### Page 49

FIGURE 2: FORWARD ENGINE MOUNT FITTING - DETAILED INSPECTION
August 31, 2000
Revision 2:  July 09, 2009 747-54A2203
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 49 of 102
BOEING SERVICE BULLETIN 747-54A2203
ALERT                                                                                                    ALERT
 
 
The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY 
numbers shown below are the numbers of parts necessary for each strut.
STEP TASK NAME PROCEDURE REFERENCES NOTES
1 Inspect Forward Engine
Mount Hanger Fitting
DET - for looseness.   
NOTE: Look for evidence of damaged or loose fasteners, fretting at the hanger fitting interface
edges, worn or shanked fasteners, and broken sealant. 
2 Inspect Fasteners - Aft Side DET - for fretting damage and signs
of fastener looseness.
NOTE: A borescope or light and mirrors may be used to accomplish the DET the aft side of the
fasteners.
3 Inspect Strut Forward Engine
Mount Bulkhead
Chords
DET - for cracks in the inner and
outer radius and at the fas-
tener rows for loose fasten-
ers.
NOTE: A borescope or light and mirrors may be used to accomplish the DET the aft side of the
chords.
4 Inspect Strut Forward Engine
Mount Bulkhead
DET - for cracks.
5 Inspect Strut Forward Engine
Mount Lower Spar
Web - Forward Bay
Only
DET - for cracks, and damaged
sealant and loose fasteners.  
NOTE: A borescope or light and mirrors may be used to accomplish the DET.
6 Inspect Strut Forward Engine
Mount Bulkhead
Channel
DET - for cracks and damage and
loose fasteners.
NOTE: A borescope or light and mirrors may be used to accomplish the DET.
(SHEET 3 OF 3)

### Page 50

FIGURE 3: FORWARD ENGINE MOUNT FITTING - TORQUE CHECK
August 31, 2000
Revision 2:  July 09, 2009 747-54A2203
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 50 of 102
BOEING SERVICE BULLETIN 747-54A2203
ALERT                                                                                                    ALERT
 
 
FIGURE  3:   FORWARD ENGINE MOUNT FITTING - TORQUE CHECK
STRUT FWD
ACCESS DOOR
A
A
FWD
A
SEE A
V32263
(SHEET 1 OF 7)

### Page 51

FIGURE 3: FORWARD ENGINE MOUNT FITTING - TORQUE CHECK
August 31, 2000
Revision 2:  July 09, 2009 747-54A2203
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 51 of 102
BOEING SERVICE BULLETIN 747-54A2203
ALERT                                                                                                    ALERT
 
 
A-A
13
12
11
10
9
8
7
6
5
13
12
11
10
9
8
7
6
5
12 3 412 3 4
'GROUP A'
'GROUP B'
UP
95
73
84
61
1
1
10 95 10
10
10
73
84 10
10
10
6 10
2 10
61 10
6 10
2 10
8
8
73 108
73 108
1337804
(SHEET 2 OF 7)

### Page 52

FIGURE 3: FORWARD ENGINE MOUNT FITTING - TORQUE CHECK
August 31, 2000
Revision 2:  July 09, 2009 747-54A2203
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 52 of 102
BOEING SERVICE BULLETIN 747-54A2203
ALERT                                                                                                    ALERT
 
 
The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY 
numbers shown below are the numbers of parts necessary for each strut.
TABLE 1: TORQUE STRIPE INSPECTION
STEP TASK NAME PART NUMBER QTY NOTES
1 Inspect Group A - Primary
Fastener (Location 1
and 4)
- 4 Do a DET of the torque stripe for
evidence of fastener rotation.
Evidence of fastener rotation is if
the edges of the stripe are not
aligned across the fastener and
the structure.  If Torque Stripe is
not aligned do a Torque Check to
determine if the fastener is un-
der-torqued.  See Table  4 for
fastener torque requirements.
2 Inspect Group A - Secondary
Fastener (Location 2
and 3)
- 4 Do a DET of the torque stripe on
the inside of the strut for evi-
dence of fastener rotation.   Evi-
dence of fastener rotation is if the
edges of the stripe are not
aligned across the fastener and
the structure.  If the torque stripe
is not aligned, the fastener is
considered under-torqued.
NOTE:  A borescope or light and mirrors may be used to accomplish the DET.
3 Check Group B - Fasteners
(Location 5, 6, 7, 10,
11, and 12) 
- 12 Do a DET of the torque stripe for
evidence of fastener rotation.
Evidence of fastener rotation is if
the edges of the stripe are not
aligned across the fastener and
the structure.  If Torque Stripe is
not aligned do a Torque Check to
determine if the fastener is un-
der-torqued or Loose.  See Table
4 for fastener torque require-
ments.
(SHEET 3 OF 7)

### Page 53

FIGURE 3: FORWARD ENGINE MOUNT FITTING - TORQUE CHECK
August 31, 2000
Revision 2:  July 09, 2009 747-54A2203
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 53 of 102
BOEING SERVICE BULLETIN 747-54A2203
ALERT                                                                                                    ALERT
 
 
4 Check Group B - Fasteners
(Location 8 and 9) 
- 4 Do a DET of the torque stripe for
evidence of fastener rotation.
Evidence of fastener rotation is if
the edges of the stripe are not
aligned across the fastener and
the structure.  Check the fasten-
ers for looseness by trying to ro-
tate the fastener by hand, the
careful use of small hand tools is
acceptable.  The fastener is con-
sidered under-torqued if evi-
dence of rotation is found, but
can not be turned by hand.
5 Check Group B - Fastener
(Location 13)
- 2 Do a DET of the torque stripe for
evidence of fastener rotation.
Evidence of fastener rotation is if
the edges of the stripe not
aligned across the fastener and
the structure.  If Torque Stripe is
not aligned do a Torque Check to
determine if the fastener is un-
der-torqued or loose.  See Table
4 for fastener torque require-
ments.
NOTE:This Step is not required if accomplishing Part 7 - HFEC Internal Angle Inspection.  The 
bolt is removed and re-torqued to accomplish Part 7 - HFEC Internal Angle Inspection.
TABLE 1: TORQUE STRIPE INSPECTION
STEP TASK NAME PART NUMBER QTY NOTES
(SHEET 4 OF 7)

### Page 54

FIGURE 3: FORWARD ENGINE MOUNT FITTING - TORQUE CHECK
August 31, 2000
Revision 2:  July 09, 2009 747-54A2203
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 54 of 102
BOEING SERVICE BULLETIN 747-54A2203
ALERT                                                                                                    ALERT
 
 
TABLE 2: TORQUE STRIPE NOT APPLIED FASTENER LOOSENESS INSPECTION
STEP TASK NAME PART NUMBER QTY NOTES
6 Torque
Check 
Group A - Primary Fastener 
(Location 1 and 4)
- 4 to determine if fastener is 
Under-torqued or loose. See 
Table 4 for torque 
requirements.
7 Torque
Check 
Group B - Fasteners 
(Location 5, 6, 7, 10, 11, 
and 12) (a)
- 12 to determine if fastener is 
Under-torqued or loose. See 
Table 4 for torque 
requirements.
8 Inspect Group B - Fasteners 
(Location 8 and 9)
- 4 Do a DET of the fastener for 
evidence of fastener rotation.   
Evidence of fastener rotation 
include: gap under head, 
fretting, cracked or broken 
sealant.  Check the fasteners 
for looseness by trying to 
rotate the fastener by hand, 
the careful use of small hand 
tools is acceptable.  The 
fastener is considered under-
torqued if evidence of rotation 
is found, but can not be 
turned by hand.
Group B - Fasteners 
(Location 5, 6, 7, 10, 11, 
and 12) (b)
12
9 Torque
Check 
Group B - Fastener 
(Location 13)
- 2 to determine if fastener is 
Under-torqued or loose. See 
Table 4 for torque 
requirements.
NOTE:This Step is not required if accomplishing Part 7 - HFEC Internal Angle Inspection.  The bolt 
is removed and re-torqued to accomplish Part 7-  Internal Angle Inspection.
(a) Bolts with washers and nuts installed. Airplanes which were affected by the original release of this service 
bulletin.
(b) Hi-lok bolts and collars installed.  Airplanes which were not affected by the original release or Revision 1 
of this service bulletin.
(SHEET 5 OF 7)

### Page 55

FIGURE 3: FORWARD ENGINE MOUNT FITTING - TORQUE CHECK
August 31, 2000
Revision 2:  July 09, 2009 747-54A2203
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 55 of 102
BOEING SERVICE BULLETIN 747-54A2203
ALERT                                                                                                    ALERT
 
 
TABLE 3: TORQUE STRIPE APPLICATION
STEP TASK NAME PART NUMBER QTY NOTES
10 Apply Lacquer F-925 22 Optional, apply torque stripe the
head of the bolt and the fitting
surface or to the nut, bolt threads
and fitting surface per operators
standard shop procedures. Refer
to 747-100/200/300 SRM
51-30-01 or 747-SP SRM
51-30-01 as accepted proce-
dures
(SHEET 6 OF 7)

### Page 56

FIGURE 3: FORWARD ENGINE MOUNT FITTING - TORQUE CHECK
August 31, 2000
Revision 2:  July 09, 2009 747-54A2203
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 56 of 102
BOEING SERVICE BULLETIN 747-54A2203
ALERT                                                                                                    ALERT
 
 
TABLE 4: FASTENER TORQUE VALUES
CODE LOCATION NAME PART NUMBER 
CONDITIONAL TORQUE 
APPLICATION
UNDER-TORQUED
(Less Than)
LOOSE
(Less Than)
Group A Fasteners
A 1, 4 Bolt NAS6706U8
NAS6706U8X
NAS6706U8y
300 in-lbs. -
B2 ,  3 - - - -
Group B Fasteners
C 5, 6, 7, 10, 11, 12 Nut BACN10HR4CS 60 in-lbs. 40 in-lbs
D 13 Nut BACN10HR5CS 130 in-lbs. 60 in-lbs
E8 ,  9 - - - -
(SHEET 7 OF 7)

### Page 57

FIGURE 4: FORWARD ENGINE MOUNT FITTING - ANY FASTENER FOUND UNDER-TORQUED OR 
LOOSE - FASTENER RE-TIGHTENING
August 31, 2000
Revision 2:  July 09, 2009 747-54A2203
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 57 of 102
BOEING SERVICE BULLETIN 747-54A2203
ALERT                                                                                                    ALERT
 
 
FIGURE  4:   FORWARD ENGINE MOUNT FITTING - ANY FASTENER FOUND UNDER-TORQUED OR 
LOOSE - FASTENER RE-TIGHTENING
1
(FASTENERS HOLE NUMBERS)
13
12
11
10
9
8
7
6
5
432
STRUT FWD
ACCESS DOOR
GROUP A FASTENER "PRIMARY"
(2 LOCATIONS PER FITTING)
GROUP B FASTENERS
(9 LOCATIONS PER FITTING)
GROUP A FASTENER "SECONDARY"
(2 LOCATIONS PER FITTING)
A
A
A
A
FWD A 1 2
A-A
SEE A
84 65 73
1 2
F
18
D
FC
FC
NE
1 2
V32264
(SHEET 1 OF 7)

### Page 58

FIGURE 4: FORWARD ENGINE MOUNT FITTING - ANY FASTENER FOUND UNDER-TORQUED OR 
LOOSE - FASTENER RE-TIGHTENING
August 31, 2000
Revision 2:  July 09, 2009 747-54A2203
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 58 of 102
BOEING SERVICE BULLETIN 747-54A2203
ALERT                                                                                                    ALERT
 
 
The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY 
numbers shown below are the numbers of parts necessary for each hanger fitting.
Check to make sure that all nut run on torques are met. Discard nuts that do not meet the following run on torque 
requirements.
NOTE:
1. If any Group A fastener was found loose or under-torqued, all Group A fasteners must be re-
tightened.
2. If any Group B fastener is found under-torqued, the under-torqued fastener must be re-tightened.  
If 4 or more Group B fasteners were found under-torqued or loose, re-tighten all Group B 
fasteners.
3. If any Group B fastener is found loose, the loose fastener must be removed and the hole 
inspected.  If 4 or more Group B fasteners were found under-torqued or loose, re-tighten all Group 
B fasteners.
4. Re-tighten Group A "Secondary" Fasteners, if fastener was not torque striped. 
5. Re-tighten Group B fasteners no.s 8 and 9, if fastener was not torque striped. 
TABLE 1: NUT RUN-ON AND BREAK-AWAY TORQUE
Nut Max Run-on Torque 
(Pound-inches)
Min Break Away 
Torque (Pound-
inches)
BACN10HR4CS 30 3.5
BACN10HR5CS 60 6.5
NAS1805-4 or
BACN11Z4CK
30 3.5
NAS1805-5 or
BACN11Z5CK
60 6.5
NAS1805-6 or
BACN11Z6CK
80 9.5
(SHEET 2 OF 7)

### Page 59

FIGURE 4: FORWARD ENGINE MOUNT FITTING - ANY FASTENER FOUND UNDER-TORQUED OR 
LOOSE - FASTENER RE-TIGHTENING
August 31, 2000
Revision 2:  July 09, 2009 747-54A2203
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 59 of 102
BOEING SERVICE BULLETIN 747-54A2203
ALERT                                                                                                    ALERT
 
 
TABLE 2: TIGHTEN UNDER-TORQUED FASTENERS (GROUP A AND B FASTENERS)
STEP TASK NAME PART NUMBER QTY NOTES
1 Tighten Fastener - 13 Loosen nut, check run-on torque
and then tighten nut of all under-
torqued fasteners to value shown
in Table 4: Fastener Torque.
2 Apply Lacquer F-925 13 Optional, apply torque stripes to
the head of the bolt and the fitting
surface or to the nut, bolt threads
and fitting surface or the bulkhead
per operators standard shop pro-
cedures. Refer to 747-100/200/
300 SRM 51-30-01 or 747-SP
SRM 51-30-01 as accepted proce-
dures.  Apply lacquer to the for-
ward surface of the bulkhead,
except fastener no.s 2 and 3
(Group A "Secondary").  Apply lac-
quer to the aft surface of the bulk-
head on fastener no.s 2 and 3
(Group A "Secondary"). 
TABLE 3: TIGHTEN LOOSE FASTENERS (GROUP B FASTENERS ONLY)
STEP TASK NAME PART NUMBER QTY NOTES
3 Remove /
Discard
Fastener - 1 at each loose fastener location.
Remove /
Keep
Radius Fillers 65B90316-7 1 at hole locations 5, 6, 7, 10, 11, or
12.  If radius filler is not installed, a
new radius filler will be required for
new bolt installation.
4 Inspect Hole - 1 for cracks as given in 747 NDT,
Part 6, 51-00-00, Figure 17.
5 Ream Hole - 1 if required, to remove damage.
Maintain 1.7 e/D.  A minimum 1/64
inch oversize is required, 1/32 inch
oversize maximum.  Break sharp
edges  0.01 - 0.02 R on fitting and
web, deburr hole.
Radius Filler 65B90316-7 1 if installed at hole locations 5, 6, 7,
10, 11, or 12.  Break sharp edges
0.04 - 0.05 R and deburr hole.
(SHEET 3 OF 7)

### Page 60

FIGURE 4: FORWARD ENGINE MOUNT FITTING - ANY FASTENER FOUND UNDER-TORQUED OR 
LOOSE - FASTENER RE-TIGHTENING
August 31, 2000
Revision 2:  July 09, 2009 747-54A2203
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 60 of 102
BOEING SERVICE BULLETIN 747-54A2203
ALERT                                                                                                    ALERT
 
 
6 Install Fastener - 1 wet with BMS 5-63 sealant.
Radius Filler 65B90316-7 1 at hole locations 5, 6, 7, 10, 11, and
12.
NOTE: Measure material stack-up to determine fastener grip length required. A maximum of three
washers may be added under the nut to adjust for grip length to prevent shanking.
7 Tighten Fastener - 9 If more than 4 under-torqued or
loose fasteners were found, loosen
nuts, check run-on torque and then
tighten nuts of all Group B fasten-
ers to torque value shown in Table
4: Fastener Torque.
8 Apply Lacquer F-925 9 Optional, apply torque stripes to
the head of the bolt and the fitting
surface or to the nut, bolt threads
and fitting surface on the forward
side of the bulkhead per operators
standard shop procedures. Refer
to 747-100/200/300 SRM
51-30-01 or 747-SP SRM
51-30-01 as accepted procedures.
TABLE 4: FASTENER TORQUE
CODE LOCATION NAME PART NUMBER NOTES
A 1, 4 Nut NAS1805-6 or
BACN11Z6CK
Torque to 390 - 410 in-lbs. Verify bolt pro-
trusion is beyond the nut as given in
747-100/200/300 SRM 51-30-02 or
747-SP SRM 51-30-02.
B 2, 3 Nut NAS1805-5 or
BACN11Z5CK
Tighten to 190 - 200 in-lbs.   Verify bolt
protrusion is beyond the nut as given in
747-100/200/300 SRM 51-30-02 or
747-SP SRM 51-30-02.
C 5, 6, 7, 10, 11, 
12 
Nut BACN10HR4CS Tighten to 90 - 100 in-lbs.   Verify bolt pro-
trusion is beyond the nut as given in
747-100/200/300 SRM 51-30-02 or
747-SP SRM 51-30-02.
D 13 Nut BACN10HR5CS Tighten to 190 - 200 in-lbs.   Verify bolt
protrusion is beyond the nut as given in
747-100/200/300 SRM 51-30-02 or
747-SP SRM 51-30-02.
E 8, 9 Nut NAS1805-4 or
BACN11Z4CK
Tighten to 75 - 80 in-lbs.   Verify bolt pro-
trusion is beyond the nut as given in
747-100/200/300 SRM 51-30-02 or
747-SP SRM 51-30-02.
TABLE 3: TIGHTEN LOOSE FASTENERS (GROUP B FASTENERS ONLY)
STEP TASK NAME PART NUMBER QTY NOTES
(SHEET 4 OF 7)

The text continues at https://openairdocs.org/service-documents/boeing/747-54a2203/file/5c9261159331.md?from=61

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
