# Boeing Alert Requirements Bulletin 747-57A2370 RB: No revision named

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2022-1059; AD 2022-23-12 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Alert Requirements Bulletin 747-57A2370 RB](https://openairdocs.org/service-documents/boeing/747-57a2370-rb.md)
- Title as filed: RB 747-57A2370 R00
- Pages: 30
- PDF: https://openairdocs.org/files/sha256/43/aa/43aa8ad981aad9a0010dd8c05dc8be5250eda1d783ad8b4f8049ca3d441c70d2
- Page: https://openairdocs.org/service-documents/boeing/747-57a2370-rb/file/43aa8ad981aa

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

<tJ--aoEIND 
Commercial 
Airplanes 
747 
Requirements Bulletin 
-------------ALERT-------------
Number: 747-57A2370 RB 
Original Issue: March 02, 2022 
ATA System : 5710 
SUBJECT: WINGS - Center Wing - Center Tank Upper Skin Inspection 
EXPORT CONTROLLED - This technology or software is subject to the U.S. Export Administration Regulations 
(EAR), (15 C.F.R. Parts 730-774) . No authorization from the U.S. Department of Commerce is required for 
export , re-export , in-country transfer , or access EXCEPT to country group E:1 or E:2 countries/persons per 
Supp.1 to Part 7 40 of the EAR. 
ECCN: 9E991 
Copyright© 2022 Boeing. 
Unpublished Work . All Rights Reserved. 
Treatment of this document and its content is governed by contract with Boeing. Rights to use this document 
are licensed on a per aircraft basis and such rights may not be transferable. For more information , contact The 
Boeing Company. 
Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner, 
BBJ, DC-8, DC-9, DC-10, KC-10, KC-46 , KDC-10 , MD-10 , MD-11, MD-80, MD-88, MD-90, P-8, Poseidon and 
Boeing liveries are all trademarks owned by The Boeing Company; and no trademark license is granted in 
connection with this document unless provided in writing by Boeing. 
Original Issue: March 02, 2022 
2.0 
7 4 7-57 A2370 RB 
1 of 30

### Page 2

ALERT 
Original Issue: March 02, 2022 
REQUIREMENTS BULLETIN 747-57A2370 
BLANK PAGE 
Export Controlled ECCN: 9E991 
Copyright© Unpublished Work - See page 1 for details. 
ALERT 
747-57A2370 RB 
2 of 30

### Page 3

REQUIREMENTS BULLETIN 747-57A2370 
ALERT ALERT 
Table of Contents 
1. EFFECTIVITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 
A. Airplanes ................................................ 5 
B. Spares Affected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 
2. CONCURRENT REQUIREMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 
3. COMPLIANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 
4. APPROVAL ................................................. 9 
5. ACCOMPLISHMENT INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 
A. General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 
B. Work Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 
FIGURE 6: LEFT SIDE -WING CENTER SECTION UPPER SKIN PANEL BETWEEN STA 1100 AND STA 
1120 - LOW FREQUENCY EDDY CURRENT {LFEC) INSPECTION ............ 13 
FIGURE 7: LEFT SIDE - WING CENTER SECTION UPPER SKIN PANEL BETWEEN STA 1140 AND STA 
1160 - LOW FREQUENCY EDDY CURRENT {LFEC) INSPECTION ............ 16 
FIGURE 8: LEFT SIDE -WING CENTER SECTION UPPER SKIN PANEL BETWEEN STA 1180 AND STA 
1200 - LOW FREQUENCY EDDY CURRENT {LFEC) INSPECTION ............ 19 
FIGURE 11: RIGHT SIDE - WING CENTER SECTION UPPER SKIN PANEL BETWEEN STA 1100 AND 
STA 1120 - LOW FREQUENCY EDDY CURRENT {LFEC) INSPECTION ......... 22 
FIGURE 12: RIGHT SIDE - WING CENTER SECTION UPPER SKIN PANEL BETWEEN STA 1140 AND 
STA 1160 - LOW FREQUENCY EDDY CURRENT {LFEC) INSPECTION ......... 25 
FIGURE 13: RIGHT SIDE - WING CENTER SECTION UPPER SKIN PANEL BETWEEN STA 1180 AND 
STA 1200- LOW FREQUENCY EDDY CURRENT {LFEC) INSPECTION ......... 28 
Original Issue: March 02, 2022 
Export Controlled ECCN: 9E991 
Copyright© Unpublished Work - See page 1 for details. 
747-57A2370 RB 
3 of 30

### Page 4

ALERT 
Original Issue: March 02, 2022 
REQUIREMENTS BULLETIN 747-57A2370 
BLANK PAGE 
Export Controlled ECCN: 9E991 
Copyright© Unpublished Work - See page 1 for details. 
ALERT 
747-57A2370 RB 
4 of 30

### Page 5

<tJ---aoEIND 
Commercial 
Airplanes 
747 
Requirements Bulletin 
-------------ALERT-------------
Number: 747-57A2370 RB 
Original Issue: March 02, 2022 
ATA System: 5710 
SUBJECT: WINGS - Center Wing - Center Tank Upper Skin Inspection 
THIS DOCUMENT IS SENT TO THE OPERATORS OF RECORD OF THE AIRPLANES SHOWN IN 
PARAGRAPH 1.A., EFFECTIVITY . IF AN AIRPLANE HAS BEEN LEASED OR SOLD, SEND THIS DOCUMENT 
TO THE NEW OPERATOR. IF APPLICABLE SPARES HAVE BEEN SOLD , SEND THIS DOCUMENT TO THE 
NEW OWNER. THIS IS AN ENHANCED REQUIRED FOR COMPLIANCE DOCUMENT. THE BOEING 
PROCESSES USED TO CREATE THE SERVICE BULLETIN (SB) AND THE REQUIREMENTS BULLETIN 
(RB) ENSURE THAT THE INFORMATION BETWEEN "RC START" AND "RC END" IN THE SB ARE IDENTICAL 
TO THE INFORMATION IN THE SAME SECTIONS (COMPLIANCE , WORK INSTRUCTIONS ... ) OF THE RB 
WHICH THE SB REFERS TO AS THE RELATED DOCUMENT. 
1. Effectivity 
A. Airplanes 
This bulletin is applicable to 747-100, 747-100B , 747-100B SUD, 747-200B , 747-200C , 747-200F , 
747-300, 747-400, 747-400D, 747-400F, 747SP, 747SR Airplane(s), line number(s) 1-1419 in 1 
Group(s). Where the effectivity is presented with hyphens between line numbers, the airplane 
applicability means "through" and "inclusive" , e.g. line numbers 1-9 means line numbers 1 through 
9 inclusive. 
The Variable Numbers and Group Information for the applicable airplanes is given below. 
GROUP CONFIGURATION DESCRIPTION 
1 - 747-100, 747-100B, 747-100B SUD, 747-200B , 747-200C, 747-200F, 
747-300, 747-400 , 747-400D , 747-400F , 747SP, 747SR Airplanes 
Airplane Models : 
747-100, 747-100B, 747-100B SUD, 747-200B, 747-200C, 747-200F, 747-300, 747-400, 747-400D, 
747-400F, 747SP, 747SR 
Variable Number Group Variable Number Group 
RA001 - RA034 1 RA201 - RA203 1 
RA101 - RA115 1 RA216 - RA217 1 
RA161 - RA164 1 RA245 - RA246 1 
Original Issue: March 02, 2022 
Export Controlled ECCN: 9E991 
Copyright © Unpublished Work - See page 1 for details . 
Variable Number Group 
RA251 - RA266 1 
RA301 - RA318 1 
RA351 - RA360 1 
7 4 7-57 A2370 RB 
5 of 30

### Page 6

REQUIREMENTS BULLETIN 747-57A2370 
ALERT 
Variable Number Group Variable Number Group 
RA369 - RA373 
RA401 - RA418 
RA501 - RA502 
RA521 - RA528 
RA532 - RA548 
RA551 - RA552 
RA559 - RA561 
RA581 - RA582 
RA585 
RA601 - RA602 
RA631 - RA635 
RA651 - RA652 
RA671 - RA677 
RA701 - RA702 
RA721 - RA731 
RA741 - RA745 
RA749- RA750 
RA761 - RA762 
RA781 - RA784 
RA901 - RA916 
RB001 - RB016 
RB041 - RB044 
RB071 - RB075 
RB101 - RB102 
RB411 - RB413 
RB421 
RB601 - RB607 
RB681 - RB697 
RB711 
RB721 - RB723 
RB741 - RB748 
RD00 1 - RD004 
RD021 - RD022 
Original Issue: March 02, 2022 
1 
1 
1 
1 
1 
1 
1 
1 
1 
1 
1 
1 
1 
1 
1 
1 
1 
1 
1 
1 
1 
1 
1 
1 
1 
1 
1 
1 
1 
1 
1 
1 
1 
RD041 - RD059 1 
RD071 - RD072 1 
RD081 - RD083 1 
RD091 - RD092 1 
RD101 - RD104 1 
RD121 - RD127 1 
RD131 - RD144 1 
RD166- RD167 1 
RD171 - RD172 1 
RD181 - RD183 1 
RD201 - RD204 1 
RD221 - RD227 1 
RD231 - RD235 1 
RD241 - RD243 1 
RD251 - RD262 1 
RD271 - RD272 1 
RD291 - RD292 1 
RD301 - RD302 1 
RD311 1 
RD351 - RD358 1 
RD361 - RD366 1 
RD381 - RD383 1 
RD411 - RD414 1 
RD421 - RD426 1 
RD431 - RD435 1 
RD441 - RD442 1 
RD451 - RD456 1 
RD461 1 
RD471 - RD475 1 
RD513- RD519 1 
RD531 - RD533 1 
RD551 1 
RD561 1 
Export Controlled ECCN: 9E991 
Copyright© Unpublished Work - See page 1 for details. 
ALERT 
Variable Number Group 
RD571 1 
RD581 - RD583 1 
RD591 - RD593 1 
RD601 - RD607 1 
RD621 - RD623 1 
RD641 - RD649 1 
RD651 - RD659 1 
RD661 1 
RD671 1 
RD681 - RD682 1 
RD691 - RD692 1 
RD701 - RD702 1 
RD721 - RD722 1 
RD741 - RD742 1 
RD751 - RD755 1 
RD761 1 
RD771 - RD775 1 
RD781 - RD783 1 
RD791 - RD792 1 
RE001 1 
RF001 - RF006 1 
RG001 - RG009 1 
RG091 1 
RG095 1 
RG101 - RG104 1 
RG121 - RG126 1 
RG141 - RG142 1 
RG161 - RG164 1 
RG171 - RG174 1 
RG191 - RG193 1 
RG211 - RG213 1 
RG221 - RG222 1 
RH101 - RH102 1 
747-57A2370 RB 
6 of 30

### Page 7

REQUIREMENTS BULLETIN 747-57A2370 
ALERT 
Variable Number Group Variable Number Group 
RH 111 - RH 112 
RH121 - RH122 
RJ131 - RJ133 
RJ151 - RJ152 
RJ301 - RJ303 
RJ321 - RJ322 
RJ331 - RJ333 
RL401 - RL403 
RL411 - RL436 
RL451 - RL456 
RL461 - RL462 
RL471 - RL481 
RL491 - RL492 
RL501 - RL502 
RL511 - RL516 
RL521 - RL522 
RL531 - RL534 
RL551 
RL561 - RL568 
RL571 - RL572 
RL576 - RL577 
RL579 
RL581 - RL586 
RL651 - RL655 
RL671 - RL675 
RL681 - RL684 
RL751 - RL752 
RM001 - RM007 
RM010 - RM013 
RM021 - RM024 
RM026 - RM030 
RM036 - RM045 
RM051 - RM053 
Original Issue: March 02, 2022 
1 
1 
1 
1 
1 
1 
1 
1 
1 
1 
1 
1 
1 
1 
1 
1 
1 
1 
1 
1 
1 
1 
1 
1 
1 
1 
1 
1 
1 
1 
1 
1 
1 
RM071 1 
RM081 - RM084 1 
RM091 1 
RM096 - RM097 1 
RM116 - RM117 1 
RM126 - RM132 1 
RM136- RM147 1 
RM156- RM158 1 
RM166 - RM177 1 
RM191 - RM192 1 
RM231 - RM233 1 
RM241 - RM246 1 
RM261 - RM264 1 
RM316 - RM318 1 
RM331 - RM333 1 
RM341 1 
RM351 - RM355 1 
RM366 - RM367 1 
RM401 - RM403 1 
RM426 1 
RM431 1 
RM441 - RM443 1 
RM445 1 
RM801 - RM803 1 
RM811 - RM813 1 
RM851 - RM859 1 
RM861 - RM863 1 
RM871 - RM899 1 
RM901 - RM906 1 
RM911 1 
RR001 - RR005 1 
RR021 - RR025 1 
RR031 1 
Export Controlled ECCN: 9E991 
Copyright© Unpublished Work - See page 1 for details. 
ALERT 
Variable Number Group 
RR201 - RR206 1 
RR221 - RR226 1 
RR261 - RR267 1 
RR301 - RR310 1 
RR331 - RR332 1 
RR336 1 
RR341 - RR345 1 
RR361 - RR362 1 
RR421 - RR422 1 
RR431 - RR432 1 
RR441 - RR442 1 
RR451 1 
RR501 - RR504 1 
RR521 - RR522 1 
RR526 1 
RR531 1 
RR551 - RR556 1 
RR561 1 
RR566 1 
RR701 1 
RR721 - RR724 1 
RR746 - RR748 1 
RR851 - RR856 1 
RR861 - RR862 1 
RR951 - RR952 1 
RS001 - RS002 1 
RS201 1 
RS211 - RS212 1 
RS221 - RS222 1 
RS231 - RS241 1 
RS251 - RS259 1 
RS263 1 
RS265 - RS268 1 
747-57A2370 RB 
7 of 30

### Page 8

ALERT 
Variable Number 
RS271 - RS276 
RS291 - RS292 
RS301 - RS306 
RS311 - RS320 
RS331 - RS333 
RS341 - RS342 
RS699 
RS701 - RS703 
RS711 - RS713 
RS721 - RS722 
RS731 - RS732 
RS741 - RS743 
RS751 - RS752 
RS761 - RS762 
RS771 
RS781 - RS782 
RS786 
RT001 - RT014 
RT021 - RT022 
RT031 - RT035 
RT041 - RT04 7 
B. Spares Affected 
None. 
REQUIREMENTS BULLETIN 747-57A2370 
Group Variable Number Group 
1 RT061 1 
1 RT071 - RT075 1 
1 RT101 - RT103 1 
1 RT121 1 
1 RT131 - RT137 1 
1 RT151 - RT152 1 
1 RT161 - RT168 1 
1 RT401 - RT412 1 
1 RT431 - RT447 1 
1 RT451 - RT469 1 
1 RT471 - RT499 1 
1 RT501 - RT535 1 
1 RT551 - RT568 1 
1 RT571 - RT591 1 
1 RT601 - RT657 1 
1 RT671 - RT673 1 
1 RT681 - RT682 1 
1 RT691 - RT699 1 
1 RT701 - RT704 1 
1 RT711 - RT717 1 
1 RT741 - RT757 1 
2. CONCURRENT REQUIREMENTS 
None. 
3. COMPLIANCE 
ALERT 
Variable Number Group 
RT776 - RT777 1 
RT781 - RT784 1 
RT801 - RT803 1 
RT811 - RT814 1 
RT831 - RT837 1 
RT861 - RT864 1 
RT876 - RT880 1 
RT931 - RT932 1 
RT945 - RT949 1 
RT951 - RT955 1 
RT966 - RT967 1 
RU001 - RU006 1 
RU016 - RU017 1 
RU031 - RU032 1 
RU051 - RU052 1 
RU059 - RU062 1 
RU081 - RU083 1 
RU101 - RU102 1 
RU121 - RU132 1 
RU801 - RU809 1 
RU831 - RU841 1 
The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to 
Requirements Bulletin 747-57A2370 RB. The Airworthiness Directive will make the compliance tasks and 
times given in Requirements Bulletin 747-57A2370 RB mandatory. 
Original Issue: March 02, 2022 
Export Controlled ECCN: 9E991 
Copyright© Unpublished Work - See page 1 for details. 
747-57A2370 RB 
8 of 30

### Page 9

REQUIREMENTS BULLETIN 747-57A2370 
ALERT ALERT 
Accomplish the required action(s), based on the applicable condition(s) in Table(s) 1, in accordance with 
Accomplishment Instructions. 
Table 1: WING CENTER SECTION UPPER SKIN PANEL - LOW FREQUENCY EDDY CURRENT (LFEC) 
INSPECTION 
Condition Action Boeing Recommended Repeat Interval 
Compliance Time (Not to Exceed) 
All Airplanes Do a Low Frequency Ed- Within 16,000 flight hours -
dy Current (LFEC) inspec- after the original issue 
tion of the wing center date of Requirements 
section upper skin panels Bulletin 747-57A2370 RB 
for heat damage. 
CONDITION 1: ANY HEAT Contact The Boeing Before further flight -
DAMAGE FOUND Company for repair in-
structions and do the re-
pair. 
CONDITION 2: NO HEAT No further action re- - -
DAMAGE FOUND quired. 
4. APPROVAL 
This Requirements Bulletin was examined by the Federal Aviation Administration (FAA). The changes 
specified in this document comply with the applicable regulations and are FAA approved, as well as European 
Union Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved 
airplanes listed in this Requirements Bulletin effectivity. This document and its approval were based on the 
airplane in its original Boeing delivery configuration or as modified by other Boeing changes. 
If an airplane has a non-Boeing modification or repair that affects a component or system also affected by 
this Requirements Bulletin, the operator is responsible for obtaining appropriate regulatory agency approval 
before incorporating this Requirements Bulletin. 
Original Issue: March 02, 2022 
Export Controlled ECCN: 9E991 
Copyright© Unpublished Work - See page 1 for details. 
747-57A2370 RB 
9 of 30

### Page 10

ALERT 
Original Issue: March 02, 2022 
REQUIREMENTS BULLETIN 747-57A2370 
BLANK PAGE 
Export Controlled ECCN: 9E991 
Copyright© Unpublished Work - See page 1 for details. 
ALERT 
747-57A2370 RB 
10 of 30

### Page 11

REQUIREMENTS BULLETIN 747-57A2370 
ALERT ALERT 
5. ACCOMPLISHMENT INSTRUCTIONS 
A. GENERAL INFORMATION 
NOTE: 1. 
2. 
3. 
4. 
5. 
6. 
7. 
This is an Enhanced Required for Compliance document. There will be a separate 
Service Bulletin (SB) and a separate Requirements Bulletin (RB). If an RB is mandated 
by an Airworthiness Directive (AD), then all applicable requirements specified in the 
RB must be done. For the related SB, some locations are marked RC Start and RC 
End to identify the requirements that are restated from the RB. For the related SB, 
the areas between RC Start and RC End, including sub-steps and any figures 
identified between RC Start and RC End, must be done to comply with the AD. 
Therefore, an Alternative Method of Compliance (AMOC) is required for any deviations 
to steps between RC Start and RC End, including substeps and identified figures. 
For the related SB, the steps not between RC Start and RC End may be deviated 
from using accepted methods in accordance with the operator's maintenance or 
inspection program without obtaining approval of an AMOC; this is provided that the 
steps between RC Start and RC End, including sub-steps and identified figures, can 
still be done as specified, and the airplane can be put back in an airworthy condition. 
Figures not required for compliance are omitted from the RB. 
This is an Enhanced Required for Compliance document. The Boeing processes 
used to create the Service Bulletin (SB) and the Requirements Bulletin (RB) ensure 
that the information between "RC Start" and "RC End" in the SB are identical to the 
information in the same sections (Compliance, Work Instructions ... ) of the RB which 
the SB refers to as the related document. 
The compliance times for the actions in WORK INSTRUCTIONS are in Compliance. 
These work instructions refer to procedures included in other Boeing documents. 
When the words "refer to" are used and the operator has an accepted alternative 
procedure, the accepted alternative procedure can be used. When the words "in 
accordance with" are included in the instruction, the procedure in the Boeing document 
must be used. 
If it is necessary to remove more parts for access, you can remove those parts. If 
you can get access without removing identified parts, it is not necessary to remove 
all of the identified parts. Jacking and shoring limitations must be observed. 
Use the approved fastener, process, and material substitutions in accordance with 
SRM Chapter 51. 
Unless shown differently, these dimensions and tolerances are used: 
Linear dimensions are in inches 
Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus 
or minus 0.03 inch 
Angular tolerance is plus or minus 2 degrees 
Hole dimensions for standard solid rivets and fasteners are in Structural Repair 
Manual (SRM) Chapter 51 
Torque Values: 
Values for structural fasteners are given in 747 Structural Repair Manual, 
Chapter 51. 
Original Issue: March 02, 2022 
Export Controlled ECCN: 9E991 
Copyright© Unpublished Work - See page 1 for details. 
747-57A2370 RB 
11 of30

### Page 12

ALERT 
REQUIREMENTS BULLETIN 747-57A2370 
ALERT 
Values for airframe maintenance tasks are included in Chapter 20 of 747 
Aircraft Maintenance Manual (AMM). 
Values for electrical maintenance tasks are included in Chapter 20 of 
Standard Wiring Practices Manual (SWPM). 
Values for engine maintenance tasks are included in Chapter 70 of 747 
Aircraft Maintenance Manual (AMM). 
Non-standard torque values for maintenance tasks are included in the 
applicable installation step. 
B. WORK INSTRUCTIONS 
Actions Required for Compliance 
1. Requirements: 
Table 1: WING CENTER SECTION UPPER SKIN PANEL - LOW FREQUENCY EDDY CURRENT (LFEC) 
INSPECTION 
Condition 
All Airplanes 
CONDITION 1: ANY HEAT 
DAMAGE FOUND 
CONDITION 2: NO HEAT 
DAMAGE FOUND 
Original Issue: March 02, 2022 
Action Method of Compliance 
-
-
Do a Low Frequency Ed- FIGURE 6 
dy Current (LFEC) inspec- FIGURE 7 
tion of the wing center FIGURE 8 
section upper skin panels FIGURE 11 
for heat damage. FIGURE 12 
FIGURE 13 
Contact The Boeing -
Company for repair in-
structions and do the re-
pair. 
-
No further action re- -
quired. 
-
Export Controlled ECCN: 9E991 
Copyright© Unpublished Work - See page 1 for details. 
Refer to the listed 
procedures in SB 
747-57A2370 
Original Issue or 
later approved re-
visions as an ac-
cepted procedure 
Do PART 1: OPEN 
ACCESS 
Do PART2: 
PREPARATION 
-
-
Do PART3: 
CLOSE ACCESS 
-
Do PART3: 
CLOSE ACCESS 
747-57A2370 RB 
12 of 30

### Page 13 (OCR)

REQUIREMENTS BULLETIN 747-57A2370
ALERT  ALERT
STRUCTURE REMOVED
FOR CLARITY
LBL
98
LBL
128
STA  STA  STA
1110  1150  1190
FWD
A-A  2987039
FIGURE 6: LEFT SIDE - WING CENTER SECTION UPPER SKIN PANEL BETWEEN STA 1100 AND STA
1120 - LOW FREQUENCY EDDY CURRENT (LFEC) INSPECTION
(SHEET 1 OF 3)
Original Issue: March 02, 2022
747-57A2370 RB
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.  13 of 30

### Page 14 (OCR)

REQUIREMENTS BULLETIN 747-57A2370
ALERT  ALERT
STA
1110
LBL.
98
D￾
- INSPECTION AREA
- MID SKIN
FWD
XX
• 0
000  • C
LBL
128
FITTING  FITTING
XX
The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
Step  Task  Name  Identification  Qty  More Data
1  Inspect  MID SKIN  (a) (b
(a) 1. Do a Low Frequency Eddy Current (LFEC) inspection for heat damage of the inspection area at each
row and column intersection to get conductivity value in accordance with 747 NDT Manual Part 6, 51-00-
00, Procedure 3.
2. Compare the conductivity value to the average corresponding value for the same column in the baseline
area for STA 1110. A conductivity change of 1 percent International Annealed Copper Standard (IACS)
or more from the baseline conductivity value indicates an area of heat damage. Identify column and row
location(s) for any heat damage found.
FIGURE 6: LEFT SIDE - WING CENTER SECTION UPPER SKIN PANEL BETWEEN STA 1100 AND STA
1120 - LOW FREQUENCY EDDY CURRENT (LFEC) INSPECTION
(SHEET 2 OF 3)
Original Issue: March 02, 2022
747-57A2370 RB
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.  14 of 30

### Page 15

REQUIREMENTS BULLETIN 747-57A2370 
ALERT ALERT 
Step I Task I Name I Identification I Qty I More Data 
(b) Do not record measurement if the probe contacts a fastener. Adjust the probe as follows: 
1. Check instrument manufacturer instructions to minimize edge effect interference of fasteners. It is ac­
ceptable for the probe to overlap grid boundary. 
2. Identify the fastener head outline using surface HFEC in accordance with 747 NDT Manual Part 6, 51-
00-00, Procedure 23. 
FIGURE 6: LEFT SIDE -WING CENTER SECTION UPPER SKIN PANEL BETWEEN STA 1100 AND STA 
1120 - LOW FREQUENCY EDDY CURRENT {LFEC) INSPECTION 
Original Issue: March 02, 2022 
{SHEET 3 OF 3) 
Export Controlled ECCN: 9E991 
Copyright© Unpublished Work - See page 1 for details. 
747-57A2370 RB 
15 of 30

### Page 16 (OCR)

REQUIREMENTS BULLETIN 747-57A2370
ALERT  ALERT
STRUCTURE REMOVED
FOR CLARITY
LBL
98
LBL
128
STA  STA  STA
1110  1150  1190
FWD
A-A  2987045
FIGURE 7: LEFT SIDE - WING CENTER SECTION UPPER SKIN PANEL BETWEEN STA 1140 AND STA
1160 - LOW FREQUENCY EDDY CURRENT (LFEC) INSPECTION
(SHEET 1 OF 3)
Original Issue: March 02, 2022
Export Controlled ECCN: 9E991  747-57A2370 RB
Copyright © Unpublished Work - See page 1 for details.  16 of 30

### Page 17 (OCR)

REQUIREMENTS BULLETIN 747-57A2370
ALERT  ALERT
STA
1150
LBL
98
D
- INSPECTION AREA
-AFT SKIN
MID SKIN  ••••••c
LBL
128
FITTING  FITTING
XX
2987046
The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
Step  Task  Name  Identification  Qty  More Data
1  Inspect  AFT SKIN  (a)(b)
(a) 1. Do a Low Frequency Eddy Current (LFEC) inspection for heat damage of the inspection area at each
row and column intersection to get conductivity value in accordance with 747 NDT Manual Part 6, 51-00-
00, Procedure 3.
2. Compare the conductivity value to the average corresponding value for the same column in the baseline
area for STA 1150. A conductivity change of 1 percent IACS or more from the baseline conductivity value
indicates an area of heat damage. Identify column and row location(s) for any heat damage found.
FIGURE 7: LEFT SIDE - WING CENTER SECTION UPPER SKIN PANEL BETWEEN STA 1140 AND STA
1160 - LOW FREQUENCY EDDY CURRENT (LFEC) INSPECTION
(SHEET 2 OF 3)
Original Issue: March 02, 2022
Export Controlled ECCN: 9E991  747-57A2370 RB
Copyright © Unpublished Work - See page 1 for details.  17 of 30

### Page 18

REQUIREMENTS BULLETIN 747-57A2370 
ALERT ALERT 
Step I Task I Name I Identification I Qty I More Data 
(b) Do not record measurement if the probe contacts a fastener. Adjust the probe as follows: 
1. Check instrument manufacturer instructions to minimize edge effect interference of fasteners. It is ac­
ceptable for the probe to overlap grid boundary. 
2. Identify the fastener head outline using surface HFEC in accordance with 747 NDT Manual Part 6, 51-
00-00, Procedure 23. 
FIGURE 7: LEFT SIDE -WING CENTER SECTION UPPER SKIN PANEL BETWEEN STA 1140 AND STA 
1160 - LOW FREQUENCY EDDY CURRENT {LFEC) INSPECTION 
Original Issue: March 02, 2022 
{SHEET 3 OF 3) 
Export Controlled ECCN: 9E991 
Copyright© Unpublished Work - See page 1 for details. 
747-57A2370 RB 
18 of 30

### Page 19 (OCR)

REQUIREMENTS BULLETIN 747-57A2370
ALERT  ALERT
STRUCTURE REMOVED
FOR CLARITY
LBL_
98
LBL
128
STA  STA  STA
1110  1150  1190
FWD
A-A  2987051
FIGURE 8: LEFT SIDE - WING CENTER SECTION UPPER SKIN PANEL BETWEEN STA 1180 AND STA
1200 - LOW FREQUENCY EDDY CURRENT (LFEC) INSPECTION
(SHEET 1 OF 3)
Original Issue: March 02, 2022
747-57A2370 RB
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.  19 of 30

### Page 20 (OCR)

REQUIREMENTS BULLETIN 747-57A2370
ALERT  ALERT
STA
1190
LBL
98
D
- INSPECTION AREA
1 AFT SKIN
POO
000
LBL
128
FITTING  FITTING
XX
The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
Step  Task  Name  Identification  Qty  More Data
1  Inspect  AFT SKIN  (a)(b)
(a) 1. Do a Low Frequency Eddy Current (LFEC) inspection for heat damage of the inspection area at each
row and column intersection to get conductivity value in accordance with 747 NDT Manual Part 6, 51-00-
00, Procedure 3.
2. Compare the conductivity value to the average corresponding value for the same column in the baseline
area for STA 1190. A conductivity change of 1 percent IACS or more from the baseline conductivity value
indicates an area of heat damage. Identify column and row location(s) for any heat damage found.
FIGURE 8: LEFT SIDE - WING CENTER SECTION UPPER SKIN PANEL BETWEEN STA 1180 AND STA
1200 - LOW FREQUENCY EDDY CURRENT (LFEC) INSPECTION
(SHEET 2 OF 3)
Original Issue: March 02, 2022
747-57A2370 RB
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.  20 of 30

### Page 21

REQUIREMENTS BULLETIN 747-57A2370 
ALERT ALERT 
Step I Task I Name I Identification I Qty I More Data 
(b) Do not record measurement if probe contacts a fastener. Adjust the probe as follows: 
1. Check instrument manufacturer instructions to minimize edge affect interference of fasteners. It is ac­
ceptable for the probe to overlap grid boundary. 
2. Identify the fastener head outline using surface HFEC in accordance with 747 NDT Manual Part 6, 51-
00-00, Procedure 23. 
FIGURE 8: LEFT SIDE -WING CENTER SECTION UPPER SKIN PANEL BETWEEN STA 1180 AND STA 
1200 - LOW FREQUENCY EDDY CURRENT {LFEC) INSPECTION 
Original Issue: March 02, 2022 
{SHEET 3 OF 3) 
Export Controlled ECCN: 9E991 
Copyright© Unpublished Work - See page 1 for details. 
747-57A2370 RB 
21 of 30

### Page 22 (OCR)

REQUIREMENTS BULLETIN 747-57A2370
ALERT  ALERT
STRUCTURE REMOVED
FOR CLARITY
— RBL  98
— RBL  128
STA  STA  STA
1190  1150  1110
FWD
A-A  2987144
FIGURE 11: RIGHT SIDE - WING CENTER SECTION UPPER SKIN PANEL BETWEEN STA 1100 AND STA
1120 - LOW FREQUENCY EDDY CURRENT (LFEC) INSPECTION
(SHEET 1 OF 3)
Original Issue: March 02, 2022
Export Controlled ECCN: 9E991  747-57A2370 RB
Copyright © Unpublished Work - See page 1 for details.  22 of 30

### Page 23 (OCR)

REQUIREMENTS BULLETIN 747-57A2370
ALERT  ALERT
STA
1110
_ RBL
98
INSPECTION AREA
MID SKIN-
- XX
0 0
•••
RBL
128
FITTING  XX  FITTING  FWD
The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
Step  Task  Name  Identification  Qty  More Data
1  Inspect  MID SKIN  (a) (b)
(a) 1. Do a Low Frequency Eddy Current (LFEC) inspection for heat damage of the inspection area at each
row and column intersection to get conductivity value in accordance with 747 NDT Manual Part 6, 51-00-
00, Procedure 3.
2. Compare the conductivity value to the average corresponding value for the same column in the baseline
area for STA 1110. A conductivity change of 1 percent IACS or more from the baseline conductivity value
indicates an area of heat damage. Identify column and row location(s) for any heat damage found.
FIGURE 11: RIGHT SIDE - WING CENTER SECTION UPPER SKIN PANEL BETWEEN STA 1100 AND STA
1120 - LOW FREQUENCY EDDY CURRENT (LFEC) INSPECTION
(SHEET 2 OF 3)
Original Issue: March 02, 2022
Export Controlled ECCN: 9E991  747-57A2370 RB
Copyright © Unpublished Work - See page 1 for details.  23 of 30

### Page 24

REQUIREMENTS BULLETIN 747-57A2370 
ALERT ALERT 
Step I Task I Name I Identification I Qty I More Data 
(b) Do not record measurement if the probe contacts a fastener. Adjust the probe as follows: 
1. Check instrument manufacturer instructions to minimize edge effect interference of fasteners. It is ac­
ceptable for the probe to overlap grid boundary. 
2. Identify the fastener head outline using surface HFEC in accordance with 747 NDT Manual Part 6, 51-
00-00, Procedure 23. 
FIGURE 11: RIGHT SIDE -WING CENTER SECTION UPPER SKIN PANEL BETWEEN STA 1100 AND STA 
1120 - LOW FREQUENCY EDDY CURRENT (LFEC) INSPECTION 
Original Issue: March 02, 2022 
(SHEET 3 OF 3) 
Export Controlled ECCN: 9E991 
Copyright© Unpublished Work - See page 1 for details. 
747-57A2370 RB 
24 of 30

### Page 25 (OCR)

REQUIREMENTS BULLETIN 747-57A2370
ALERT  ALERT
STRUCTURE REMOVED
FOR CLARITY
_ RBL
98
PRES
STA  STA  STA
1190  1150  1110
FWD
A-A  2987152
FIGURE 12: RIGHT SIDE - WING CENTER SECTION UPPER SKIN PANEL BETWEEN STA 1140 AND STA
1160 - LOW FREQUENCY EDDY CURRENT (LFEC) INSPECTION
(SHEET 1 OF 3)
Original Issue: March 02, 2022
747-57A2370 RB
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.  25 of 30

### Page 26 (OCR)

REQUIREMENTS BULLETIN 747-57A2370
ALERT  ALERT
STA
1150
_ RBL
98
- D
INSPECTION AREA -
AFT SKIN
• XX
000
• 0  • MID SKIN
RBL
128
FITTING  FITTING
XX
2987154
The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
Step  Task  Name  Identification  Qty  More Data
1  Inspect  AFT SKIN  (a)(b)
(a) 1. Do a Low Frequency Eddy Current (LFEC) inspection for heat damage of the inspection area at each
row and column intersection to get conductivity value in accordance with 747 NDT Manual Part 6, 51-00-
00, Procedure 3.
2. Compare the conductivity value to the average corresponding value for the same column in the baseline
area for STA 1150. A conductivity change of 1 percent IACS or more from the baseline conductivity value
indicates an area of heat damage. Identify column and row location(s) for any heat damage found.
FIGURE 12: RIGHT SIDE - WING CENTER SECTION UPPER SKIN PANEL BETWEEN STA 1140 AND STA
1160 - LOW FREQUENCY EDDY CURRENT (LFEC) INSPECTION
(SHEET 2 OF 3)
Original Issue: March 02, 2022
747-57A2370 RB
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.  26 of 30

### Page 27

REQUIREMENTS BULLETIN 747-57A2370 
ALERT ALERT 
Step I Task I Name I Identification I Qty I More Data 
(b) Do not record measurement if probe contacts a fastener. Adjust the probe as follows: 
1. Check instrument manufacturer instructions to minimize edge effect interference of fasteners. It is ac­
ceptable for the probe to overlap grid boundary. 
2. Identify the fastener head outline using surface HFEC in accordance with 747 NDT Manual Part 6, 51-
00-00, Procedure 23. 
FIGURE 12: RIGHT SIDE -WING CENTER SECTION UPPER SKIN PANEL BETWEEN STA 1140 AND STA 
1160 - LOW FREQUENCY EDDY CURRENT (LFEC) INSPECTION 
Original Issue: March 02, 2022 
(SHEET 3 OF 3) 
Export Controlled ECCN: 9E991 
Copyright© Unpublished Work - See page 1 for details. 
747-57A2370 RB 
27 of 30

### Page 28 (OCR)

REQUIREMENTS BULLETIN 747-57A2370
ALERT  ALERT
STRUCTURE REMOVED
FOR CLARITY
— RBL  98
- RBL  128
STA  STA  STA
1190  1150  1110
FWD
A-A  2987155
FIGURE 13: RIGHT SIDE - WING CENTER SECTION UPPER SKIN PANEL BETWEEN STA 1180 AND STA
1200 - LOW FREQUENCY EDDY CURRENT (LFEC) INSPECTION
(SHEET 1 OF 3)
Original Issue: March 02, 2022
Export Controlled ECCN: 9E991  747-57A2370 RB
Copyright © Unpublished Work - See page 1 for details.  28 of 30

### Page 29 (OCR)

REQUIREMENTS BULLETIN 747-57A2370
ALERT  ALERT
STA
1190
_ RBL
98
- D
INSPECTION AREA
AFT SKIN
FWD
XX
RBL
128
FITTING  FITTING
XX
The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
Step  Task  Name  Identification  Qty  More Data
Inspect  AFT SKIN  (a)(D)
(a) 1. Do a Low Frequency Eddy Current (LFEC) inspection for heat damage of the inspection area at each
row and column intersection to get conductivity value in accordance with 747 NDT Manual Part 6, 51-00-
00, Procedure 3.
2. Compare the conductivity value to the average corresponding value for the same column in the baseline
area for STA 1190. A conductivity change of 1 percent IACS or more from the baseline conductivity value
indicates an area of heat damage. Identify column and row location(s) for any heat damage found.
FIGURE 13: RIGHT SIDE - WING CENTER SECTION UPPER SKIN PANEL BETWEEN STA 1180 AND STA
1200 - LOW FREQUENCY EDDY CURRENT (LFEC) INSPECTION
(SHEET 2 OF 3)
Original Issue: March 02, 2022
Export Controlled ECCN: 9E991  747-57A2370 RB
Copyright © Unpublished Work - See page 1 for details.  29 of 30

### Page 30

REQUIREMENTS BULLETIN 747-57A2370 
ALERT ALERT 
Step I Task I Name I Identification I Qty I More Data 
(b) Do not record measurement if the probe contacts a fastener. Adjust the probe as follows: 
1. Check instrument manufacturer instructions to minimize edge effect interference of fasteners. It is ac­
ceptable for the probe to overlap grid boundary. 
2. Identify the fastener head outline using surface HFEC in accordance with 747 NDT Manual Part 6, 51-
00-00, Procedure 23. 
FIGURE 13: RIGHT SIDE -WING CENTER SECTION UPPER SKIN PANEL BETWEEN STA 1180 AND STA 
1200 - LOW FREQUENCY EDDY CURRENT (LFEC) INSPECTION 
Original Issue: March 02, 2022 
(SHEET 3 OF 3) 
Export Controlled ECCN: 9E991 
Copyright© Unpublished Work - See page 1 for details. 
747-57A2370 RB 
30 of 30

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
