# Boeing Special Attention Requirements Bulletin 757-25-0320 RB: Revision 1

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2025-0003; AD 2026-21-12 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Special Attention Requirements Bulletin 757-25-0320 RB](https://openairdocs.org/service-documents/boeing/757-25-0320-rb.md)
- Title as filed: 757-25-0320 RB
- Pages: 12
- PDF: https://openairdocs.org/files/sha256/aa/07/aa077b446a15b29dc4869d87608d0e15b2ce1f9779fcabfb5357a488315de7e4
- Page: https://openairdocs.org/service-documents/boeing/757-25-0320-rb/file/aa077b446a15

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Commercial 
Airplanes
757
Requirements Bulletin
SPECIAL ATTENTION
Number: 757-25-0320 RB
Original Issue: January 19, 2024
ATA System: 2523 2332
SUBJECT: EQUIPMENT/FURNISHINGS - Passenger Compartment - Passenger Service
Unit-Mounted Video Monitor Replacement
EXPORT CONTROLLED - This technology or software is subject to the U.S. Export Administration Regulations
(EAR), (15 C.F.R. Parts 730-774). No authorization from the U.S. Department of Commerce is required for
export, re-export, in-country transfer, or access EXCEPT to country group E:1 or E:2 countries/persons per
Supp.1 to Part 740 of the EAR.
9E991ECCN:
Copyright © 2024 The Boeing Company
Treatment of this document and its content is governed by contract with Boeing. Rights to use this document
are licensed on a per aircraft basis and such rights may not be transferable. For more information, contact The
Boeing Company.
Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner,
BBJ, DC-8, DC-9, DC-10, KC-10, KC-46, KDC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8, Poseidon and
Boeing liveries are all trademarks owned by The Boeing Company; and no trademark license is granted in
connection with this document unless provided in writing by Boeing.
Original Issue: January 19, 2024
757-25-0320 RB
1 of 12
4.0

### Page 2

Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: January 19, 2024
757-25-0320 RB
2 of 12
REQUIREMENTS BULLETIN 757-25-0320
BLANK PAGE

### Page 3

Table of Contents
1. EFFECTIVITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
A. Airplanes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
B. Spares Affected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2. CONCURRENT REQUIREMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3. COMPLIANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4. APPROVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
5. ACCOMPLISHMENT INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
A. General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
B. Work Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
FIGURE 1: PASSENGER COMPARTMENT - PASSENGER SERVICE UNIT-MOUNTED VIDEO MONITOR
- REPLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: January 19, 2024
757-25-0320 RB
3 of 12
REQUIREMENTS BULLETIN 757-25-0320

### Page 4

Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: January 19, 2024
757-25-0320 RB
4 of 12
REQUIREMENTS BULLETIN 757-25-0320
BLANK PAGE

### Page 5

Commercial 
Airplanes
757
Requirements Bulletin
SPECIAL ATTENTION
Number: 757-25-0320 RB
Original Issue: January 19, 2024
ATA System: 2523 2332
SUBJECT: EQUIPMENT/FURNISHINGS - Passenger Compartment - Passenger Service
Unit-Mounted Video Monitor Replacement
BOEING RECOMMENDS THAT EACH OPERATOR EXAMINE THIS DOCUMENT IMMEDIATELY. THIS IS
AN ENHANCED REQUIRED FOR COMPLIANCE DOCUMENT. THE BOEING PROCESSES USED TO CREATE
THE SERVICE BULLETIN (SB) AND THE REQUIREMENTS BULLETIN (RB) ENSURE THAT THE
INFORMATION BETWEEN "RC START" AND "RC END" IN THE SB ARE IDENTICAL TO THE INFORMATION
IN THE SAME SECTIONS (COMPLIANCE, WORK INSTRUCTIONS…) OF THE RB WHICH THE SB REFERS
TO AS THE RELATED DOCUMENT.
1. Effectivity
A. Airplanes
This bulletin is applicable to 757-200, 757-300 Airplane(s), line number(s) 732, 736, 738, 741-744,
749-750, 752, 754, 756-758, 760, 764, 770, 777, 802, 805, 819, 821, 825, 836, 854, 858, 869,
874-875, 878, 883-884, 886, 891, 893, 896, 901, 907, 928, 932, 954, 957, 960, 963, 972, 976,
978, 980, 985, 1003, 1007-1008, 1017-1018, 1031-1032 in 1 Group(s). Where the effectivity is
presented with hyphens between line numbers, the airplane applicability means "through" and
"inclusive", e.g. line numbers 1-9 means line numbers 1 through 9 inclusive.
The Variable Numbers and Group Information for the applicable airplanes is given below. This
bulletin is not applicable if a passenger airplane has been modified to a freighter configuration by
Boeing and re-delivered as a Special Freighter (SF) configuration via Boeing STC ST00916WI-D.
DESCRIPTIONCONFIGURATIONGROUP
757-200, 757-300 Airplanes equipped with Passenger Service
Unit-mounted video monitors, part numbers 617-6265-001 and
617-6265-002.
-1
Airplane Models:
757-200, 757-300
GroupVariable Number
1NB226 - NB228
1NB230
GroupVariable Number
1NC076 - NC084
1NC091 - NC094
GroupVariable Number
1NL001 - NL002
1NL006 - NL017
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: January 19, 2024
757-25-0320 RB
5 of 12

### Page 6

GroupVariable Number
1NT232 - NT234
1NT237 - NT238
GroupVariable Number
1NT351 - NT360
1NT371 - NT373
GroupVariable Number
1NT375 - NT379
1NT441 - NT442
B. Spares Affected
Examine your spares supply for the parts or components identified below. If any parts or components
are found, refer to Paragraph 2.C.3., Parts Modified and Reidentified in SB 757-25-0320 for the
recommended action.
Part Number
617-6265-001
617-6265-002
2. CONCURRENT REQUIREMENTS
None.
3. COMPLIANCE
The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to
Requirements Bulletin 757-25-0320 RB. The Airworthiness Directive will make the compliance tasks and
times given in Requirements Bulletin 757-25-0320 RB mandatory.
Accomplish the required action(s), based on the applicable condition(s) in Table 1 in accordance with
Accomplishment Instructions.
TABLE 1: PASSENGER SERVICE UNIT-MOUNTED VIDEO MONITOR REPLACEMENT
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
-Within 60 months
after the Original
Issue date of Re-
quirements Bulletin
757-25-0320 RB.
At all Passenger Service
Unit (PSU) locations re-
place any PSU-mounted
video monitor without
secondary retention lan-
yards with PSU-mounted
video monitor with sec-
ondary retention lan-
yards. Make sure each
inboard lanyard is at-
tached to the inboard
PSU rail.
All airplanes.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: January 19, 2024
757-25-0320 RB
6 of 12
REQUIREMENTS BULLETIN 757-25-0320

### Page 7

4. APPROVAL
This Requirements Bulletin was examined by the Federal Aviation Administration (FAA). The changes
specified in this document comply with the applicable regulations and are FAA approved, as well as European
Union Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved
airplanes listed in this Requirements Bulletin effectivity. This document and its approval were based on the
airplane in its original Boeing delivery configuration or as modified by other Boeing changes.
If an airplane has a non-Boeing modification or repair that affects a component or system also affected by
this Requirements Bulletin, the operator is responsible for obtaining appropriate regulatory agency approval
before incorporating this Requirements Bulletin.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: January 19, 2024
757-25-0320 RB
7 of 12
REQUIREMENTS BULLETIN 757-25-0320

### Page 8

Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: January 19, 2024
757-25-0320 RB
8 of 12
REQUIREMENTS BULLETIN 757-25-0320
BLANK PAGE

### Page 9

5.    ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL INFORMATION
NOTE: 1. This is an Enhanced Required for Compliance document. There will be a separate
Service Bulletin (SB) and a separate Requirements Bulletin (RB). If an RB is mandated
by an Airworthiness Directive (AD), then all applicable requirements specified in the
RB must be done. In the RB, the "Refer to the listed procedures..." column of the
table(s) in the Work Instructions is for reference only. The procedures in that column
are not required by the AD and are for guidance only. For the related SB, some
locations are marked RC Start and RC End to identify the requirements that are
restated from the RB. For the related SB, the areas between RC Start and RC End,
including sub-steps and any figures identified between RC Start and RC End, must
be done to comply with the AD. Therefore, an Alternative Method of Compliance
(AMOC) is required for any deviations to steps between RC Start and RC End,
including substeps and identified figures. For the related SB, the steps not between
RC Start and RC End may be deviated from using accepted methods in accordance
with the operator's maintenance or inspection program without obtaining approval
of an AMOC; this is provided that the steps between RC Start and RC End, including
sub-steps and identified figures, can still be done as specified, and the airplane can
be put back in an airworthy condition. Figures not required for compliance are omitted
from the RB.
2. This is an Enhanced Required for Compliance document. The Boeing processes
used to create the Service Bulletin (SB) and the Requirements Bulletin (RB) ensure
that the information between "RC Start" and "RC End" in the SB are identical to the
information in the same sections (Compliance, Work Instructions...) of the RB which
the SB refers to as the related document.
3. The compliance times for the actions in WORK INSTRUCTIONS are in Compliance.
4. Unless shown differently, these dimensions and tolerances are used:
– Linear dimensions are in inches
– Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus
or minus 0.03 inch
– Tolerance on rivet and bolt edge margin is plus or minus 0.05 inch
– Angular tolerance is plus or minus 2 degrees
– Hole dimensions for standard solid rivets and fasteners are in Structural Repair
Manual (SRM) Chapter 51
– Torque Values:
— Values for airframe maintenance tasks are included in Chapter 20 of
757-200/300 Aircraft Maintenance Manual (AMM).
— Values for electrical maintenance tasks are included in Chapter 20 of
Standard Wiring Practices Manual (SWPM).
5. These work instructions refer to procedures included in other Boeing documents.
When the words "refer to" are used and the operator has an accepted alternative
procedure, the accepted alternative procedure can be used. When the words "in
accordance with" are included in the instruction, the procedure in the Boeing document
must be used.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: January 19, 2024
757-25-0320 RB
9 of 12
REQUIREMENTS BULLETIN 757-25-0320

### Page 10

6. If it is necessary to remove more parts for access, you can remove those parts. If
you can get access without removing identified parts, it is not necessary to remove
all of the identified parts. Jacking and shoring limitations must be observed.
7. Use of colors in Figures is based on guidance from the ATA e-Business Program
(ATA) iSpec 2200.
B. WORK INSTRUCTIONS
Actions Required for Compliance
1. Requirements
TABLE 1: PASSENGER SERVICE UNIT-MOUNTED VIDEO MONITOR REPLACEMENT
Refer to the listed proce-
dures in SB 757-25-0320
Original Issue or later
approved revisions as an
accepted procedure
Method of ComplianceActionCondition
-FIGURE 1At all Passenger Service
Unit (PSU) locations, re-
place any PSU-mounted
video monitor without sec-
ondary retention lanyards
with PSU-mounted video
monitor with secondary re-
tention lanyards. Make
sure each inboard lanyard
is attached to the inboard
PSU rail.
All Airplanes.
PART 1: PASSENGER
SERVICE UNIT-MOUNT-
ED VIDEO MONITOR -
INSTALLATION TEST
-
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: January 19, 2024
757-25-0320 RB
10 of 12
REQUIREMENTS BULLETIN 757-25-0320

### Page 11 (OCR)

REQUIREMENTS BULLETIN 757-25-0320
PASSENGER COMPARTMENT  FWD
(EXAMPLE)
SECONDARY RETENTION  INBOARD
LANYARDS  PSU RAIL
INBOARD
LANYARD
PSU-MOUNTED VIDEO MONITOR
WITH SECONDARY RETENTION
LANYARDS
2969256
FIGURE 1: PASSENGER COMPARTMENT - PASSENGER SERVICE UNIT-MOUNTED VIDEO MONITOR -
REPLACEMENT
(SHEET 1 OF 2)
Original Issue: January 19, 2024
Export Controlled ECCN: 9E991  757-25-0320 RB
See page 1 for details  11 of 12

### Page 12

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for each Passenger Service Unit (PSU)-mounted
video monitor location.
More DataQtyIdentificationNameTaskStep
(a)1617-6265-001VIDEO MONITOR, LHRemove1
(a)1617-6265-002VIDEO MONITOR, RHRemove
(a)(b)1617-6265-003VIDEO MONITOR, LHInstall (New)2
(a)(b)1617-6265-004VIDEO MONITOR, RHInstall (New)
(c)(d)1-TORSION SPRINGAttach3
(a) Refer to 757 AMM 23-32-08 as an accepted procedure.
(b) As an option, a changed part identified with the new part number in accordance with Burrana SB 617-
6265-44-01 Revision 1 or later revisions can be used instead of a new part.
(c) Attach torsion spring as follows:
– Attach the torsion spring in the nearest larger hole in the inboard PSU rail.
– Make sure torsion spring is compressed to get the hooks fully into the larger hole of the inboard PSU
rail.
– Release compression and pull down on inboard lanyard. Make sure the hooks of a torsion spring are
fully engaged in the hole.
– The torsion spring can have a firm grip within the hole or torsion spring may turn freely in the hole of
the inboard PSU rail as the PSU-mounted video monitor is closed.
Note: The 'nearest' larger hole in the inboard PSU rail is defined in this bulletin as the 1.0 inch Diameter
hole in the PSU rail that lets the inboard lanyards have the least amount of tension, when the inboard
lanyard is attached to the PSU rail and PSU-mounted video monitor.
(d) For any location where the torsion spring can not be correctly attached in accordance with footnote (c),
contact The Boeing Company for alternative installation instructions and do the installation.
FIGURE 1: PASSENGER COMPARTMENT - PASSENGER SERVICE UNIT-MOUNTED VIDEO MONITOR -
REPLACEMENT
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: January 19, 2024
757-25-0320 RB
12 of 12
REQUIREMENTS BULLETIN 757-25-0320

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
