# Boeing Alert Service Bulletin 757-27A0154: No revision named

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2016-9111; AD 2017-04-07 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Alert Service Bulletin 757-27A0154](https://openairdocs.org/service-documents/boeing/757-27a0154.md)
- Title as filed: FAA-2016-9111_SB-757-27A0154
- Pages: 21
- PDF: https://openairdocs.org/files/sha256/38/ad/38ad6a78efa8222ed841a93e643b95c8c511acb6d651ffa529d6f050b34e4476
- Page: https://openairdocs.org/service-documents/boeing/757-27a0154/file/38ad6a78efa8

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Commercial 
Airplanes
757
Service Bulletin
ALERT
Number: 757-27A0154
Original Issue: July 22, 2016
ATA System: 2761
SUBJECT: FLIGHT CONTROLS - Spoiler/Speedbrake Control System - Spoiler Power Control
Unit Replacement
Export of this technology is controlled under the United States Export Administration Regulations (EAR) (15
CFR 300-774). An export license may be required before it is used for development, production or use by foreign
persons from specific countries. The controller of this data has the individual responsibility to abide by all export
laws.
9E991ECCN:
BOEING PROPRIETARY, CONFIDENTIAL AND/OR TRADE SECRET
Copyright © 2016 Boeing.
Unpublished Work. All Rights Reserved.
Treatment of this document and its content is governed by contract with Boeing. Rights to use this document
are licensed on a per aircraft basis and such rights may not be transferable. For more information, contact The
Boeing Company.
Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner,
BBJ, DC-8, DC-9, DC-10, KC-10, KC-46, KDC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8, Poseidon and
Boeing liveries are all trademarks owned by The Boeing Company; and no trademark license is granted in
connection with this document unless provided in writing by Boeing.
Original Issue: July 22, 2016
757-27A0154
1 of 21
7.0

### Page 2

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 22, 2016
757-27A0154
2 of 21
BOEING SERVICE BULLETIN 757-27A0154
ALERTALERT
BLANK PAGE

### Page 3

Table of Contents
Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1. PLANNING INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
A. Effectivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1. Airplanes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2. Spares Affected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
B. Concurrent Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
C. Reason . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
D. Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
E. Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
F. Approval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
G. Manpower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
H. Weight and Balance Changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
I. Electrical Load Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
J. References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
1. Existing Data: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2. Data Supplied with this Service Bulletin: . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3. Installation Drawings Used in the Preparation of this Service Bulletin: . . . . . . . . . . . 16
K. Publications Affected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
L. Interchangeability and Intermixability of Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
M. Software Accomplishment Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2. MATERIAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
A. Material - Price and Availability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
B. Industry Support Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
C. Parts Necessary for Each Airplane . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
1. Kits/Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2. Parts and Materials Supplied by the Operator . . . . . . . . . . . . . . . . . . . . . . . . 17
3. Parts Modified and Reidentified . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
4. Parts Removed and Not Replaced . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
D. Parts Necessary to Change Spares . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
E. Special Tooling - Price and Availability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
F. Special Tooling Necessary to do this Service Bulletin . . . . . . . . . . . . . . . . . . . . . . . 18
3. ACCOMPLISHMENT INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
A. GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
B. WORK INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 22, 2016
757-27A0154
3 of 21
BOEING SERVICE BULLETIN 757-27A0154
ALERTALERT

### Page 4

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 22, 2016
757-27A0154
4 of 21
BOEING SERVICE BULLETIN 757-27A0154
ALERTALERT
BLANK PAGE

### Page 5

Commercial 
Airplanes
757
Service Bulletin
ALERT
SummaryNumber: 757-27A0154Original Issue: July 22, 2016
ATA System: 2761
SUBJECT: FLIGHT CONTROLS - Spoiler/Speedbrake Control System - Spoiler Power Control
Unit Replacement
THIS DOCUMENT IS SENT TO THE OPERATORS OF RECORD OF THE AIRPLANES SHOWN IN
PARAGRAPH 1.A., EFFECTIVITY. IF AN AIRPLANE HAS BEEN LEASED OR SOLD, SEND THIS DOCUMENT
TO THE NEW OPERATOR. IF APPLICABLE SPARES HAVE BEEN SOLD, SEND THIS DOCUMENT TO THE
NEW OWNER.
CONCURRENT REQUIREMENTS
None.
BACKGROUND
Accomplishment of this service bulletin will prevent an uncommanded extension of affected spoiler Power Control
Units (PCU's) during a hydraulic pressure loss event. If this service bulletin is not done, multiple spoiler PCU's
could extend during a hydraulic pressure loss event which could result in an uncommanded roll of the airplane.
Boeing has received reports of single and multiple uncommanded spoiler panel extensions during flight. The
condition known as "spoiler panel float" occurred when there was a hydraulic system pressure loss and the flaps
were extended beyond 20 degrees. A subsequent investigation by Boeing and the supplier MOOG, which
included an examination of returned defective spoiler PCU's from in-service airplanes, found that the spoiler
PCU's Blocking and Thermal Relief Valve (BTRV) housings had reached a point of fatigue that made them likely
to develop internal failures. One purpose of the spoiler PCU BTRV is to prevent the spoiler from extending during
a loss of hydraulic pressure. As a result, MOOG developed a new spoiler PCU BTRV design, where the spoiler
PCU BTRV housing material was changed from aluminium to stainless steel. The new stainless steel housing
greatly improves the fatigue capacity of the spoiler PCU BTRV Housing.
This service bulletin gives instructions to replace affected spoiler PCU's with improved spoiler PCU's that have
new improved BTRV housings. Installation of spoiler PCU's with the improved BTRV housings will prevent
multiple uncommanded extensions of spoiler PCU's in the event of a single hydraulic system failure.
Boeing Fleet Team Digest (FTD) 757 FTD 27-14001 is related to this service bulletin.
Boeing Fleet Team Safety (FTS) 757 FTS 27-14022 is related to this service bulletin.
Boeing Service Letter (SL) 757-SL-27-65 and (SL) 757-SL-27-68 are related to this service bulletin.
Boeing Service Related Problem (SRP) 757-SRP-27-0276 is related to this service bulletin.
Boeing Service Bulletin 757-27A0105 and 757-27-0156 are related to this service bulletin.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 22, 2016
757-27A0154
5 of 21

### Page 6

Federal Aviation Administration (FAA) Airworthiness Directive (AD) 92-17-10 is related to this service bulletin.
MOOG SB 3321500-27-14 is related to this service bulletin.
This table is provided to operators for planning purposes only. Refer to the applicable sections for more
information.
ReferenceAffectedPlanning Data
Paragraph 1.A.2., Spares AffectedYesSpares Affected
Paragraph 1.E., Compliance and Paragraph
1.F., Approval
YesAD Related
Paragraph 1.H., Weight and Balance ChangesNoWeight and Balance Change
Paragraph 1.I., Electrical Load DataNoElectrical Load Changed
Paragraph 1.K., Publications AffectedYesPublications Affected
Paragraph 1.K., Publications AffectedNoAirplane Flight Operations Affected (Flight Crew
Operations Manual and/or FAA Approved Air-
plane Flight Manual)
Paragraph 2.C.1., Kits/PartsNoKits/Parts Required
Paragraph 2.C.2., Parts and Materials Supplied
by the Operator
YesOperator Supplied Parts/Material
Paragraph 2.F., Special Tooling Necessary to
do this Service Bulletin
NoSpecial Tooling Required
ACTION
Get access to the left and right wing and replace the Power Control Units (PCU's) at spoiler positions 2, 3, 4
and 9, 10, 11.
EFFECTIVITY
All 757-200/-200CB/-200PF/-300 Airplane(s). Refer to Paragraph 1.A.1., Airplanes, for the list of affected
airplane(s).
Refer to Paragraph 1.A.2., Spares Affected, for the list of affected components.
COMPLIANCE
The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to this service
bulletin. The Airworthiness Directive will make the compliance tasks and times given in this service bulletin
mandatory.
Boeing recommends that the change given in this service bulletin be done within 51 months after the original
issue date of this service bulletin.
INDUSTRY SUPPORT INFORMATION
Boeing warranty remedies are not available for the repair procedure given in this service bulletin.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 22, 2016
757-27A0154
6 of 21
BOEING SERVICE BULLETIN 757-27A0154
ALERTALERT

### Page 7

MANPOWER
Refer to Paragraph 1.G., Manpower.
MATERIAL INFORMATION
Operator Supplied Parts/Materials.
Refer to Paragraph 2.A., Material - Price and Availability.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 22, 2016
757-27A0154
7 of 21
BOEING SERVICE BULLETIN 757-27A0154
ALERTALERT

### Page 8 (OCR)

BOEING SERVICE BULLETIN 757-27A0154
ALERT  ALERT
A POSITION 1  SPOILE
POSITION 11 LA  SPOILER  A POSITIO  POSITIONS
A SPOILER  POSITION 4
SPOILER
POSITION 2
SPOILER
POSITION 3
SPOILER
ELECTRICAL
CONNECTOR
REPLACE THE POWER
CONTROL UNITS (PCU'S)
AT SPOILER POSITIONS  SPOILER POWER CONTROL UNIT
2,3,4 AND 9,10,11.  (TYPICAL)  ACTUATOR
2479066
Original Issue: July 22, 2016
Export Controlled ECCN: 9E991 - BOEING  757-27A0154
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  8 of 21

### Page 9

Commercial 
Airplanes
757
Service Bulletin
ALERT
Number: 757-27A0154
Original Issue: July 22, 2016
ATA System: 2761
SUBJECT: FLIGHT CONTROLS - Spoiler/Speedbrake Control System - Spoiler Power Control
Unit Replacement
THIS DOCUMENT IS SENT TO THE OPERATORS OF RECORD OF THE AIRPLANES SHOWN IN
PARAGRAPH 1.A., EFFECTIVITY. IF AN AIRPLANE HAS BEEN LEASED OR SOLD, SEND THIS DOCUMENT
TO THE NEW OPERATOR. IF APPLICABLE SPARES HAVE BEEN SOLD, SEND THIS DOCUMENT TO THE
NEW OWNER.
1.    PLANNING INFORMATION
A. Effectivity
1. Airplanes
Refer to Service Bulletin Index D624N001 Part 3 for Airplane Variable Number, Line Number, and
Serial Number data.
This service bulletin is applicable to 757-200/-200CB/-200PF/-300 Airplanes, line numbers 1 thru
1050 in 1 Group. The Variable Numbers and Group Information for the applicable airplanes is
given below.
DESCRIPTIONCONFIGURATIONGROUP
All 757-200/-200CB/-200PF/-300 airplanes with spoiler Power Control
Units (PCU's) MOOG P/N 3321500-( ) installed.
-1
Airplane Models:
757-200, 757-200CB, 757-200PF, 757-300
GroupVariable Number
1NA001 - NA028
1NA191 - NA199
1NA201 - NA239
1NA301 - NA305
1NA341 - NA352
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 22, 2016
757-27A0154
9 of 21

### Page 10

GroupVariable Number
1NA391 - NA399
1NA401 - NA408
1NA441 - NA447
1NA501 - NA586
1NB001 - NB004
1NB021 - NB023
1NB036 - NB041
1NB051 - NB053
1NB061 - NB073
1NB079
1NB131 - NB148
1NB161 - NB162
1NB166 - NB168
1NB201 - NB204
1NB221 - NB228
1NB230
1NB236
1NB239
1NB261 - NB267
1NB291 - NB299
1NB301 - NB302
1NB311 - NB312
1NB321 - NB331
1NB421 - NB438
1NB446
1NB451 - NB454
1NB501 - NB523
1NB561
1NB571
1NB581 - NB583
1NC001 - NC033
1NC041 - NC042
1NC051 - NC052
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 22, 2016
757-27A0154
10 of 21
BOEING SERVICE BULLETIN 757-27A0154
ALERTALERT

### Page 11

GroupVariable Number
1NC056 - NC062
1NC066 - NC084
1NC091 - NC094
1NC151
1NC161
1NC901 - NC951
1NC971 - NC974
1ND001 - ND007
1ND011 - ND059
1ND111 - ND113
1ND161 - ND199
1ND201 - ND203
1ND221 - ND225
1ND241 - ND248
1ND301 - ND322
1ND401
1ND891
1ND895
1NE001 - NE008
1NE011 - NE088
1NE091 - NE094
1NE141 - NE150
1NE161 - NE177
1NE201 - NE204
1NE301 - NE302
1NE311 - NE325
1NJ001 - NJ004
1NJ031 - NJ032
1NJ551 - NJ555
1NL001 - NL002
1NL006 - NL017
1NL101 - NL109
1NL141
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 22, 2016
757-27A0154
11 of 21
BOEING SERVICE BULLETIN 757-27A0154
ALERTALERT

### Page 12

GroupVariable Number
1NL601 - NL616
1NN001 - NN002
1NN051 - NN052
1NP901 - NP904
1NS601 - NS616
1NT001 - NT009
1NT201 - NT202
1NT231 - NT234
1NT237 - NT240
1NT242
1NT245 - NT248
1NT281 - NT289
1NT341 - NT347
1NT351 - NT360
1NT371 - NT373
1NT375 - NT379
1NT381 - NT386
1NT401 - NT409
1NT411 - NT412
1NT426 - NT427
1NT431 - NT432
1NT436 - NT438
1NT441 - NT442
1NT446
1NT701 - NT769
1NT791 - NT796
1NT861 - NT862
1NT881 - NT885
1NT901 - NT916
1NT971 - NT985
1NU031 - NU038
1NU701 - NU705
1NU721 - NU728
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 22, 2016
757-27A0154
12 of 21
BOEING SERVICE BULLETIN 757-27A0154
ALERTALERT

### Page 13

GroupVariable Number
1NU731 - NU732
2. Spares Affected
Examine your spares supply for the parts or components identified below. If any parts or components
are found, refer to Paragraph 3.B., Work Instructions for the recommended action.
NamePart Number
Spoiler Power Control
Unit
MOOG P/N 3321500-12 thru 3321500-16 (Boeing
P/N S251N111-12 thru S251N111-14)
Spoiler Power Control
Unit
MOOG P/N 3321500-3A thru 3321500-11A (Boeing
P/N S251N111-3A thru S251N111-11A)
B. Concurrent Requirements
None.
C. Reason
Accomplishment of this service bulletin will prevent an uncommanded extension of affected spoiler
Power Control Units (PCU's) during a hydraulic pressure loss event. If this service bulletin is not done,
multiple spoiler PCU's could extend during a hydraulic pressure loss event which could result in an
uncommanded roll of the airplane.
Boeing has received reports of single and multiple uncommanded spoiler panel extensions during flight.
The condition known as "spoiler panel float" occurred when there was a hydraulic system pressure
loss and the flaps were extended beyond 20 degrees. A subsequent investigation by Boeing and the
supplier MOOG, which included an examination of returned defective spoiler PCU's from in-service
airplanes, found that the spoiler PCU's Blocking and Thermal Relief Valve (BTRV) housings had reached
a point of fatigue that made them likely to develop internal failures. One purpose of the spoiler PCU
BTRV is to prevent the spoiler from extending during a loss of hydraulic pressure. As a result, MOOG
developed a new spoiler PCU BTRV design, where the spoiler PCU BTRV housing material was
changed from aluminium to stainless steel. The new stainless steel housing greatly improves the fatigue
capacity of the spoiler PCU BTRV Housing.
This service bulletin gives instructions to replace affected spoiler PCU's with improved spoiler PCU's
that have new improved BTRV housings. Installation of spoiler PCU's with the improved BTRV housings
will prevent multiple uncommanded extensions of spoiler PCU's in the event of a single hydraulic system
failure.
Boeing Fleet Team Digest (FTD) 757 FTD 27-14001 is related to this service bulletin.
Boeing Fleet Team Safety (FTS) 757 FTS 27-14022 is related to this service bulletin.
Boeing Service Letter (SL) 757-SL-27-65 and (SL) 757-SL-27-68 are related to this service bulletin.
Boeing Service Related Problem (SRP) 757-SRP-27-0276 is related to this service bulletin.
Boeing Service Bulletin 757-27A0105 and 757-27-0156 are related to this service bulletin.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 22, 2016
757-27A0154
13 of 21
BOEING SERVICE BULLETIN 757-27A0154
ALERTALERT

### Page 14

Federal Aviation Administration (FAA) Airworthiness Directive (AD) 92-17-10 is related to this service
bulletin.
MOOG SB 3321500-27-14 is related to this service bulletin.
D. Description
Get access to the left and right wing and replace the Power Control Units (PCU's) at spoiler positions
2, 3, 4 and 9, 10, 11.
The work in this service bulletin is done in the maintenance zone(s) given below.
Affected Maintenance Zones
ZoneModel
562, 563, 564, 662, 663, 664757-200, 757-200CB, 757-
200PF, 757-300
E. Compliance
The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to
this service bulletin. The Airworthiness Directive will make the compliance tasks and times given in this
service bulletin mandatory.
Boeing recommends that the change given in this service bulletin be done within 51 months after the
original issue date of this service bulletin.
F. Approval
This service bulletin was examined by the Federal Aviation Administration (FAA). The changes specified
in this service bulletin comply with the applicable regulations and are FAA approved, as well as European
Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved
airplanes listed in the service bulletin effectivity. This service bulletin and its approval were based on
the airplane in its original Boeing delivery configuration or as modified by other approved Boeing
changes.
If an airplane has a non-Boeing modification or repair that affects a component or system also affected
by this service bulletin, the operator is responsible for obtaining appropriate regulatory agency approval
before incorporating this service bulletin.
In addition, the Manager of the FAA Los Angeles Aircraft Certification Office approves the action of
replacing or reworking the spoiler Power Control Units (PCUs) at spoiler positions 2, 3, 4 and 9, 10,
11 as defined in this service bulletin as an alternative method of compliance to the requirements of
paragraphs (c) and (d) of AD 92-17-10 for airplanes line number 1 thru 408. All provisions of AD 92-17-10
that are not specifically referenced in the above statement remain fully applicable and must be complied
with.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 22, 2016
757-27A0154
14 of 21
BOEING SERVICE BULLETIN 757-27A0154
ALERTALERT

### Page 15

G. Manpower
The table below shows an estimate of the task hours necessary to do this replacement for each airplane.
This estimate is for direct labor only, done by an experienced crew. Adjust the estimate with operator
task hour data if necessary. The estimate does not include lost time. These are some examples of lost
time:
• Time to adjust to the workplace
• Time to schedule the work
• Time to inspect the work
• Time to cure the materials
• Time to make the parts
• Time to find the tools
Elapsed HoursTask HoursNumber of PersonsTask
1.001.001Open Access (a)
3.006.002Spoiler PCU Replace-
ment (a)
1.001.001Close Access (a)
1.001.001Spoiler Power Con-
trol Unit (PCU) - Test
(a)
6.009.00TOTAL FOR EACH AIRPLANE
(a) The task hours and elapsed hours given is the time necessary for replacement
of six PCU's at spoiler positions 2, 3, 4 and 9, 10, 11.
The time to make the change in accordance with MOOG SB 3321500-27-14 is not included.
H. Weight and Balance Changes
None.
I. Electrical Load Data
Not changed.
J. References
1. Existing Data:
a. Boeing Service Bulletin 757-27A0105, 757-27-0156
b. Boeing Service Letter 757-SL-27-65, 757-SL-27-68
c. Boeing Service Related Problem (SRP) 757-SRP-27-0276
d. Federal Aviation Administration (FAA) Airworthiness Directive (AD) 92-17-10
e. Service Bulletin Index D624N001
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 22, 2016
757-27A0154
15 of 21
BOEING SERVICE BULLETIN 757-27A0154
ALERTALERT

### Page 16

f. 757 Aircraft Maintenance Manual (AMM) 27-61-02
g. 757 Fleet Team Digest (FTD) 27-14001
h. MOOG Service Bulletin 3321500-27-14
NOTE: The supplier was told to send copies of the service bulletin to each operator.
2. Data Supplied with this Service Bulletin:
None.
3. Installation Drawings Used in the Preparation of this Service Bulletin:
None.
K. Publications Affected
1. Publications:
Chapter-SectionPublication
27-61757 Illustrated Parts Catalog
Equipment-List757 Wiring Diagram Manual
2. Damage Tolerance Based Structural Inspections:
Boeing has evaluated the repairs and/or changes in this service bulletin for effects on Fatigue
Critical Structure (FCS) and for changes to Damage Tolerance Inspections (DTI) required in the
Maintenance Program. This service bulletin does not affect FCS, therefore DTIs are not necessary.
L. Interchangeability and Intermixability of Parts
Refer to Paragraph 2.C., Parts Necessary for Each Airplane, for interchangeability and intermixability
information.
M. Software Accomplishment Summary
Not affected.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 22, 2016
757-27A0154
16 of 21
BOEING SERVICE BULLETIN 757-27A0154
ALERTALERT

### Page 17

2.    MATERIAL INFORMATION
A. Material - Price and Availability
The operator can supply the parts and materials shown in Paragraph 2.C., Parts Necessary for Each
Airplane. Refer to MOOG SB 3321500-27-14, Rev 1: Jun 10/16.
B. Industry Support Information
Boeing warranty remedies are not available for the repair procedure given in this service bulletin.
C. Parts Necessary for Each Airplane
1. Kits/Parts
None.
2. Parts and Materials Supplied by the Operator
The following parts or materials are necessary to do the change in this service bulletin. Parts and
materials in the manuals given in Paragraph 1.J., References, can also be necessary. Examine
operator part and material supply to make sure all necessary parts and materials are available.
NotesExisting Part NumberNameQTYPart Number / Specification
(a) (b) (c)
(d)
-Flight Spoiler Power Con-
trol Unit (PCU) (Positions
2, 3, 4 and 9, 10, 11)
6MOOG P/N 3321500-17 (Boeing P/N
S251N111-15) or MOOG P/N 3321500-
18 (Boeing P/N S251N111-16)
(a) As an option to the installation of a new spoiler PCU, an existing spoiler PCU changed in accordance with
MOOG SB 3321500-27-14 Rev 1: Jun 10/16, can be installed.
(b) Seed units are available for the turnaround programme. A limited number of seed/loan units are available
to assist operators if needed. Refer to MOOG SB 3321500-27-14 Rev 1: Jun 10/16.
(c) The quantity given is the maximum number of spoiler PCU's necessary if OPTION 1 is selected for all
spoiler positions 2, 3, 4 and 9, 10, 11.
(d) You cannot use the existing part to replace the new or changed part. Refer to the Work Instructions for
possible existing part numbers.
3. Parts Modified and Reidentified
Refer to MOOG SB 3321500-27-14 Rev 1: Jun 10/16.
4. Parts Removed and Not Replaced
None.
D. Parts Necessary to Change Spares
Refer to MOOG SB 3321500-27-14 Rev 1: Jun 10/16.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 22, 2016
757-27A0154
17 of 21
BOEING SERVICE BULLETIN 757-27A0154
ALERTALERT

### Page 18

E. Special Tooling - Price and Availability
None.
F. Special Tooling Necessary to do this Service Bulletin
No special tools or equipment are necessary to do the change in this service bulletin. But, maintenance
and overhaul tools in the manuals given in Paragraph 1.J., References, can be necessary. Examine
operator tool supply to make sure all necessary tools are available.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 22, 2016
757-27A0154
18 of 21
BOEING SERVICE BULLETIN 757-27A0154
ALERTALERT

### Page 19

3.    ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL INFORMATION
CAUTION: KEEP THE WORK AREA, WIRES AND ELECTRICAL BUNDLES CLEAN OF METAL
PARTICLES OR CONTAMINATION WHEN YOU USE TOOLS. UNWANTED MATERIAL,
METAL PARTICLES OR CONTAMINATION CAUGHT IN WIRE BUNDLES CAN CAUSE
DAMAGE TO THE BUNDLES. DAMAGED WIRE BUNDLES CAN CAUSE SPARKS OR
OTHER ELECTRICAL DAMAGE.
NOTE: 1. Manual titles are referred to by acronyms. Refer to Paragraph 1.J., References, for
definition of the acronyms.
2. Obey all of the warnings and cautions given in the specified manual sections.
3. Unless shown differently, these dimensions and tolerances are used:
– Linear dimensions are in inches
– Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus
or minus 0.03 inch
– Tolerance on rivet and bolt edge margin is plus or minus 0.05 inch
– Angular tolerance is plus or minus 2 degrees
– Hole dimensions for standard solid rivets and fasteners are in Structural Repair
Manual (SRM) Chapter 51
– Torque Values:
— Values for structural fasteners are given in 757 Structural Repair Manual,
Chapter 51.
— Values for airframe maintenance tasks are included in Chapter 20 of 757
Aircraft Maintenance Manual (AMM).
— Non-standard torque values for maintenance tasks are included in the
applicable installation step.
4. These work instructions refer to procedures included in other Boeing documents.
When the words "refer to" are used and the operator has an accepted alternative
procedure, the accepted alternative procedure can be used. When the words "in
accordance with" are included in the instruction, the procedure in the Boeing document
must be used.
5. If it is necessary to remove more parts for access, you can remove those parts. If
you can get access without removing identified parts, it is not necessary to remove
all of the identified parts. Jacking and shoring limitations must be observed.
6. Where the work instructions include installation of a kept part, a new or serviceable
part with the same part number can be installed as an alternative to the kept part.
7. The compliance times for the actions in Paragraph 3.B., WORK INSTRUCTIONS
are in Paragraph 1.E., Compliance.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 22, 2016
757-27A0154
19 of 21
BOEING SERVICE BULLETIN 757-27A0154
ALERTALERT

### Page 20

8. Some steps in the Work Instructions are labeled as Required for Compliance (RC).
If this service bulletin is mandated by an Airworthiness Directive (AD), then the steps
labeled as RC, including sub-steps under an RC step and any figures identified in
an RC step, must be done to comply with the AD. An Alternative Method of
Compliance (AMOC) is required for any deviations to RC steps, including sub-steps
and identified figures. Steps not labeled as RC may be deviated from using accepted
methods in accordance with the operator's maintenance or inspection program without
obtaining approval of an AMOC. This is provided that the RC steps, including
sub-steps and identified figures, can still be done as specified, and the airplane can
be put back in an airworthy condition.
9. Refer to Paragraph 2.C.2., Parts and Materials Supplied by the Operator for
information related to the supplier turnaround program for a spoiler Power Control
Unit (PCU).
10. The spoiler Power Control Units (PCU's) referenced in this service bulletin can also
be identified as Power Control Actuators (PCA's) in other Boeing maintenance
documentation.
B. WORK INSTRUCTIONS
1. RC. Get access to and replace each spoiler Power Control Unit (PCU) at spoiler positions 2, 3, 4
on the left wing and spoiler positions 9, 10, 11 on the right wing using one of the options that follow.
a. OPTION 1: Replace each existing spoiler PCU with a new spoiler PCU as specified in the
table below. Refer to 757 AMM 27-61-02 as an accepted procedure.
New P/N'sPossible Existing P/N'sSpoiler Positions
3321500-17 or 3321500-18
(Boeing P/N S251N111-15 or
S251N111-16)
3321500-12 thru 3321500-16
(Boeing P/N S251N111-12 thru
S251N111-14)
2, 3, 4 and 9, 10, 11
3321500-3A thru 3321500-11A
(Boeing P/N S251N111-3A thru
S251N111-11A)
b. OPTION 2: Replace each existing spoiler PCU with a changed spoiler PCU as specified in
the table below. Refer to 757 AMM 27-61-02 as an accepted procedure.
New P/N'sPossible Existing P/N'sSpoiler Positions
3321500-3B thru 3321500-16B
(Boeing P/N S251N111-3B thru
S251N111-14B)
3321500-12 thru 3321500-16
(Boeing P/N S251N111-12 thru
S251N111-14) (a)
2, 3, 4 and 9, 10, 11
3321500-3A thru 3321500-11A
(Boeing P/N S251N111-3A thru
S251N111-11A) (b)
(a) MOOG P/N 3321500-12 thru 3321500-16 (Boeing P/N S251N111-12 thru S251N111-
14) are changed to MOOG P/N 3321500-12B thru 3321500-16B (Boeing P/N S251N111-
12B thru S251N111-14B) in accordance with MOOG SB 3321500-27-14, Rev 1: Jun
10/16.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 22, 2016
757-27A0154
20 of 21
BOEING SERVICE BULLETIN 757-27A0154
ALERTALERT

### Page 21

New P/N'sPossible Existing P/N'sSpoiler Positions
(b) MOOG P/N 3321500-3A thru 3321500-11A (Boeing P/N S251N111-3A thru S251N111-
11A) are changed to MOOG P/N 3321500-3B thru 3321500-11B (Boeing P/N S251N111-
3B thru S251N111-11B) in accordance with MOOG SB 3321500-27-14, Rev 1: Jun 10/16.
2. Close Access.
3. Do the spoiler PCU Test. Refer to 757 AMM 27-61-02 as an accepted procedure.
NOTE: This test is also identified as "Spoiler PCA Test" in 757 AMM 27-61-02.
4. Put the airplane back to a serviceable condition.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 22, 2016
757-27A0154
21 of 21
BOEING SERVICE BULLETIN 757-27A0154
ALERTALERT

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
