# Boeing Alert Requirements Bulletin 757-29A0071 RB: Revision 1, part 1 of 8

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2026-11821, the docket of a proposed AD (Federal Register 2026-22383). Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Alert Requirements Bulletin 757-29A0071 RB](https://openairdocs.org/service-documents/boeing/757-29a0071-rb.md)
- Title as filed: 757-29A0071 RB R1_Part1
- Pages: 53
- PDF: https://openairdocs.org/files/sha256/36/d1/36d1056e3d77fe3d4a276ec86977f87943953d009baf19126d6c6dba3d5043ed
- Page: https://openairdocs.org/service-documents/boeing/757-29a0071-rb/file/36d1056e3d77

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Commercial 
Airplanes
757
Requirements Bulletin
ALERT
Number: 757-29A0071 RB
Original Issue: November 16, 2023
Revision 1: May 28, 2026
ATA System: 2922
SUBJECT: HYDRAULIC POWER - Hydraulic Power Transfer Unit System - Relay Installation and
Wire Bundle Replacement
EXPORT CONTROLLED - This technology or software is subject to the U.S. Export Administration Regulations
(EAR), (15 C.F.R. Parts 730-774). No authorization from the U.S. Department of Commerce is required for
export, re-export, in-country transfer, or access EXCEPT to country group E:1 or E:2 countries/persons per
Supp.1 to Part 740 of the EAR.
9E991ECCN:
Copyright © 2026 The Boeing Company
Treatment of this document and its content is governed by contract with Boeing. Rights to use this document
are licensed on a per aircraft basis and such rights may not be transferable. For more information, contact The
Boeing Company.
Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner,
BBJ, DC-8, DC-9, DC-10, KC-10, KC-46, KDC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8, Poseidon and
Boeing liveries are all trademarks owned by The Boeing Company; and no trademark license is granted in
connection with this document unless provided in writing by Boeing.
Original Issue: November 16, 2023
757-29A0071 RBRevision 1: May 28, 2026
1 of 286
4.0

### Page 2

Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: November 16, 2023
757-29A0071 RBRevision 1: May 28, 2026
2 of 286
REQUIREMENTS BULLETIN 757-29A0071
ALERTALERT
BLANK PAGE

### Page 3

Table of Contents
Revision Transmittal Sheet ............................................ 7
1. EFFECTIVITY ............................................... 1 3
A. Airplanes ............................................... 1 3
B. Spares Affected ........................................... 1 7
2. CONCURRENT REQUIREMENTS .................................... 1 7
3. COMPLIANCE ............................................... 1 7
4. APPROVAL ................................................ 2 1
5. ACCOMPLISHMENT INSTRUCTIONS .................................. 2 3
A. General Information ......................................... 2 3
B. Work Instructions ........................................... 2 5
FIGURE 1: P33 PANEL - RELAYS K10902 AND K10904 - INSTALLATION [Group 1-8, Configuration 1]
.................................................. 3 8
FIGURE 2: P33 PANEL - WIRE BUNDLE W1230 - WIRE ROUTING [Group 1-5, 7-8, Configuration 1] . 40
FIGURE 3: P33 PANEL - WIRE BUNDLE W1230 - CHANGE [Group 1-5, 7-8, Configuration 1] .... 4 2
FIGURE 4: P33 PANEL - ELECTRICAL CONNECTOR D43312J - INSTALLATION [Group 1-8, Configuration
1 ]  ................................................ 4 5
FIGURE 5: BETWEEN P11 PANEL AND P33 PANEL - WIRE BUNDLE W2360 - WIRE ROUTING [Group
1-8, Configuration 1] ...................................... 4 7
FIGURE 6: BETWEEN P11 PANEL AND P33 PANEL - WIRE BUNDLE W2360 - CHANGE [Group 1-8,
Configuration 1] ......................................... 5 1
FIGURE 7: BETWEEN P33 PANEL AND DISCONNECT BRACKET AD1090 - WIRE BUNDLE W4236 -
REMOVAL [Group 1-2, 4, 8, Configuration 1] ......................... 5 3
FIGURE 8: BETWEEN P33 PANEL AND DISCONNECT BRACKET AD0880 - WIRE BUNDLE W4236 -
WIRE ROUTING [Group 1-2, Configuration 1] ........................ 5 4
FIGURE 9: BETWEEN P33 PANEL AND DISCONNECT BRACKET AD0880 - WIRE BUNDLE W4236 -
INSTALLATION [Group 1-2, Configuration 1] ......................... 6 6
FIGURE 10: RIGHT BODY FAIRING - FEEDTHRU SEALS - INSTALLATION [Group 1-4, 7-8, Configuration
1 ]  ................................................ 6 9
FIGURE 11: RIGHT FORWARD CARGO MIXBAY - WIRE BUNDLE W4236 CLAMP - INSTALLATION [Group
1-2, 4, 8, Configuration 1] ................................... 7 1
FIGURE 12: DISCONNECT BRACKET AD0880 - ELECTRICAL CONNECTOR D43412J AND WIRE BUNDLE
CLAMP - INSTALLATION [Group 1-2, 8, Configuration 1] .................. 7 3
FIGURE 13: BETWEEN DISCONNECT BRACKET AD1090 AND POWER TRANSFER UNIT CONTROL
VALVE - WIRE BUNDLE W2514 - REMOVAL [Group 1, 3, 7-8, Configuration 1] ..... 7 5
FIGURE 14: BETWEEN DISCONNECT BRACKET AD0880 AND POWER TRANSFER UNIT CONTROL
VALVE - WIRE BUNDLE W2514 - WIRE ROUTING [Group 1, 8, Configuration 1] ..... 7 6
FIGURE 15: BETWEEN DISCONNECT BRACKET AD0880 AND POWER TRANSFER UNIT CONTROL
VALVE - WIRE BUNDLE W2514 - INSTALLATION [Group 1, 8, Configuration 1] ..... 7 9
FIGURE 16: RIGHT WHEEL WELL BULKHEAD - FEEDTHRU SEALS - INSTALLATION [Group 1-8,
Configuration 1] ......................................... 8 1
FIGURE 17: BETWEEN DISCONNECT BRACKET AD1090 AND POWER TRANSFER UNIT CONTROL
VALVE - WIRE BUNDLE W2514 - REMOVAL [Group 2, Configuration 1] ......... 8 3
FIGURE 18: BETWEEN DISCONNECT BRACKET AD0880 AND POWER TRANSFER UNIT CONTROL
VALVE - WIRE BUNDLE W2514 - WIRE ROUTING [Group 2, Configuration 1] ...... 8 4
FIGURE 19: BETWEEN DISCONNECT BRACKET AD0880 AND POWER TRANSFER UNIT CONTROL
VALVE - WIRE BUNDLE W2514 - INSTALLATION [Group 2, Configuration 1] ....... 8 7
FIGURE 20: BETWEEN P33 PANEL AND DISCONNECT BRACKET AD0770 - WIRE BUNDLE W6670 -
REMOVAL [Group 3, 7, Configuration 1] ........................... 8 9
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: November 16, 2023
757-29A0071 RBRevision 1: May 28, 2026
3 of 286
REQUIREMENTS BULLETIN 757-29A0071
ALERTALERT

### Page 4

FIGURE 21: BETWEEN DISCONNECT BRACKET AD0770 AND DISCONNECT BRACKET AD1090 - WIRE
BUNDLE W5770 - REMOVAL [Group 3, 7, Configuration 1] ................. 9 0
FIGURE 22: BETWEEN P33 PANEL AND DISCONNECT BRACKET AD0880 - WIRE BUNDLE W4236 -
WIRE ROUTING [Group 4, Configuration 1] ......................... 9 1
FIGURE 23: BETWEEN P33 PANEL AND DISCONNECT BRACKET AD0880 - WIRE BUNDLE W4236 -
INSTALLATION [Group 4, Configuration 1] ......................... 1 0 3
FIGURE 24: DISCONNECT BRACKET AD0880 - ELECTRICAL CONNECTOR D43412J AND WIRE BUNDLE
CLAMP - INSTALLATION [Group 4, Configuration 1] .................... 1 0 6
FIGURE 25: BETWEEN DISCONNECT BRACKET AD1090 AND POWER TRANSFER UNIT CONTROL
VALVE - WIRE BUNDLE W2514 - REMOVAL [Group 4, Configuration 1] ......... 1 0 8
FIGURE 26: BETWEEN DISCONNECT BRACKET AD0880 AND POWER TRANSFER UNIT CONTROL
VALVE - WIRE BUNDLE W2514 - WIRE ROUTING [Group 4, Configuration 1] ..... 1 0 9
FIGURE 27: BETWEEN DISCONNECT BRACKET AD0880 AND POWER TRANSFER UNIT CONTROL
VALVE - WIRE BUNDLE W2514 - INSTALLATION [Group 4, Configuration 1] ...... 1 1 2
FIGURE 28: BETWEEN P33 AND DISCONNECT BRACKET AD0881 - WIRE BUNDLE W4236 - REMOVAL
[Group 5, Configuration 1] .................................. 1 1 4
FIGURE 29: BETWEEN P33 PANEL AND DISCONNECT BRACKET AD0881 - WIRE BUNDLE W4236 -
WIRE ROUTING [Group 5, Configuration 1] ......................... 1 1 5
FIGURE 30: BETWEEN P33 AND DISCONNECT BRACKET AD0881 - WIRE BUNDLE W4236 -
INSTALLATION [Group 5, Configuration 1] ......................... 1 2 7
FIGURE 31: RIGHT BODY FAIRING - FEEDTHRU - INSTALLATION [Group 5, Configuration 1] . . . 130
FIGURE 32: RIGHT FORWARD CARGO MIXBAY - WIRE BUNDLE W4236 CLAMP - INSTALLATION [Group
5, Configuration 1] ....................................... 1 3 2
FIGURE 33: DISCONNECT BRACKET AD0881 - ELECTRICAL CONNECTOR D43412J - INSTALLATION
[Group 5, Configuration 1] .................................. 1 3 4
FIGURE 34: BETWEEN DISCONNECT BRACKET AD0881 AND POWER TRANSFER UNIT CONTROL
VALVE - WIRE BUNDLE W2514 - REMOVAL [Group 5, Configuration 1] ......... 1 3 6
FIGURE 35: BETWEEN DISCONNECT BRACKET AD0881 AND POWER TRANSFER UNIT CONTROL
VALVE - WIRE BUNDLE W2514 - WIRE ROUTING [Group 5, Configuration 1] ..... 1 3 7
FIGURE 36: BETWEEN DISCONNECT BRACKET AD0881 AND POWER TRANSFER UNIT CONTROL
VALVE - WIRE BUNDLE W2514 - INSTALLATION [Group 5, Configuration 1] ...... 1 4 0
FIGURE 37: P33 PANEL - WIRE BUNDLE W1230 - WIRE ROUTING [Group 6, Configuration 1] . . . 142
FIGURE 38: P33 PANEL - WIRE BUNDLE W1230 - CHANGE [Group 6, Configuration 1] ....... 1 4 4
FIGURE 39: BETWEEN P33 PANEL AND DISCONNECT BRACKET AE0503 - WIRE BUNDLE W4058 -
REMOVAL [Group 6, Configuration 1] ............................ 1 4 7
FIGURE 40: BETWEEN E5-3 SHELF AND DISCONNECT BRACKET AE0503 - WIRE BUNDLE W1200 -
REMOVAL [Group 6, Configuration 1] ............................ 1 4 8
FIGURE 41: BETWEEN DISCONNECT BRACKET AE0503 AND DISCONNECT BRACKET AD0881 - WIRE
BUNDLE W4010 - REMOVAL [Group 6, Configuration 1] ................. 1 4 9
FIGURE 42: BETWEEN P33 PANEL AND DISCONNECT BRACKET AD0881 - WIRE BUNDLE W4236 -
WIRE ROUTING [Group 6, Configuration 1] ......................... 1 5 0
FIGURE 43: BETWEEN P33 AND DISCONNECT BRACKET AD0881 - WIRE BUNDLE W4236 -
INSTALLATION [Group 6, Configuration 1] ......................... 1 6 2
FIGURE 44: RIGHT BODY FAIRING - FEEDTHRU - INSTALLATION [Group 6, Configuration 1] . . . 165
FIGURE 45: DISCONNECT BRACKET AD0881 - ELECTRICAL CONNECTOR D43412J - INSTALLATION
[Group 6, Configuration 1] .................................. 1 6 7
FIGURE 46: BETWEEN DISCONNECT BRACKET AD0881 AND POWER TRANSFER UNIT CONTROL
VALVE - WIRE BUNDLE W2514 - REMOVAL [Group 6, Configuration 1] ......... 1 6 9
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: November 16, 2023
757-29A0071 RBRevision 1: May 28, 2026
4 of 286
REQUIREMENTS BULLETIN 757-29A0071
ALERTALERT

### Page 5

FIGURE 47: BETWEEN DISCONNECT BRACKET AD0881 AND POWER TRANSFER UNIT CONTROL
VALVE - WIRE BUNDLE W2514 - WIRE ROUTING [Group 6, Configuration 1] ..... 1 7 0
FIGURE 48: BETWEEN DISCONNECT BRACKET AD0881 AND POWER TRANSFER UNIT CONTROL
VALVE - WIRE BUNDLE W2514 - INSTALLATION [Group 6, Configuration 1] ...... 1 7 3
FIGURE 49: BETWEEN P33 PANEL AND DISCONNECT BRACKET AD0880 - WIRE BUNDLE W4236 -
WIRE ROUTING [Group 7, Configuration 1] ......................... 1 7 5
FIGURE 50: BETWEEN P33 PANEL AND DISCONNECT BRACKET AD0880 - WIRE BUNDLE W4236 -
INSTALLATION [Group 3, Configuration 1] ......................... 1 8 8
FIGURE 51: DISCONNECT BRACKET AD0880 - ELECTRICAL CONNECTOR D43412J AND WIRE BUNDLE
CLAMP - INSTALLATION [Group 3, 7, Configuration 1] .................. 1 9 1
FIGURE 52: BETWEEN DISCONNECT BRACKET AD0880 AND POWER TRANSFER UNIT CONTROL
VALVE - WIRE BUNDLE W2514 - WIRE ROUTING [Group 3, 7, Configuration 1] .... 1 9 3
FIGURE 53: BETWEEN DISCONNECT BRACKET AD0880 AND POWER TRANSFER UNIT CONTROL
VALVE - WIRE BUNDLE W2514 - INSTALLATION [Group 3, 7, Configuration 1] .... 1 9 6
FIGURE 54: FORWARD CARGO COMPARTMENT - DISCONNECT BRACKET AD0770 - DRILL HOLE
[Group 3, 7, Configuration 1] ................................. 1 9 9
FIGURE 55: BETWEEN P33 PANEL AND DISCONNECT BRACKET AD0880 - WIRE BUNDLE W4236 -
WIRE ROUTING [Group 3, Configuration 1] ......................... 2 0 1
FIGURE 56: BETWEEN P33 PANEL AND DISCONNECT BRACKET AD0880 - WIRE BUNDLE W4236 -
WIRE ROUTING [Group 8, Configuration 1] ......................... 2 1 3
FIGURE 57: MORE WORK - WIRE BUNDLE W4236 - CLAMP REPLACEMENT [Group 1-3, 7-8, Configuration
2 ]  ................................................ 2 2 4
FIGURE 58: MORE WORK - WIRE BUNDLE W4236 - LACING TAPE INSTALLATION [Group 1-2, 8,
Configuration 2] ........................................ 2 2 6
FIGURE 59: MORE WORK - WIRE BUNDLE W4236 - GROUND CHANGE [Group 1-2, 4, 8, Configuration
2 ]  ................................................ 2 2 8
FIGURE 60: MORE WORK - WIRE BUNDLE W4236 GROUND - WIRING CHANGE [Group 1-2, 4, 8,
Configuration 2] ........................................ 2 3 0
FIGURE 61: MORE WORK - WIRE BUNDLE W2514 - LACING TAPE INSTALLATION [Group 1, 3, 7-8,
Configuration 2] ........................................ 2 3 1
FIGURE 62: MORE WORK - WIRE BUNDLE W2514 - LACING TAPE INSTALLATION [Group 2, Configuration
2 ]  ................................................ 2 3 5
FIGURE 63: MORE WORK - WIRE BUNDLE W4236 - LACING TAPE INSTALLATION [Group 3, 7,
Configuration 2] ........................................ 2 3 9
FIGURE 64: MORE WORK - WIRE BUNDLE W4236 GROUND - CHANGE [Group 3, 7, Configuration 2]
................................................. 2 4 1
FIGURE 65: MORE WORK - WIRE BUNDLE W4236 GROUND - WIRING CHANGE [Group 3, 7, Configuration
2 ]  ................................................ 2 4 3
FIGURE 66: MORE WORK - WIRE BUNDLE W4236 - CLAMP REPLACEMENT [Group 4, Configuration 2]
................................................. 2 4 4
FIGURE 67: MORE WORK - WIRE BUNDLE W4236 - LACING TAPE INSTALLATION [Group 4, Configuration
2 ]  ................................................ 2 4 6
FIGURE 68: MORE WORK - WIRE BUNDLE W2514 - LACING TAPE INSTALLATION [Group 4, Configuration
2 ]  ................................................ 2 4 8
FIGURE 69: MORE WORK - WIRE BUNDLE W4236 - LACING TAPE INSTALLATION [Group 5, Configuration
2 ]  ................................................ 2 5 2
FIGURE 70: MORE WORK - WIRE BUNDLE W2514 - LACING TAPE INSTALLATION [Group 5, Configuration
2 ]  ................................................ 2 5 4
FIGURE 71: MORE WORK - WIRE BUNDLE W4236 - CLAMP REPLACEMENT [Group 6, Configuration 2]
................................................. 2 5 8
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: November 16, 2023
757-29A0071 RBRevision 1: May 28, 2026
5 of 286
REQUIREMENTS BULLETIN 757-29A0071
ALERTALERT

### Page 6

FIGURE 72: MORE WORK - WIRE BUNDLE W4236 - LACING TAPE INSTALLATION [Group 6, Configuration
2 ]  ................................................ 2 6 1
FIGURE 73: MORE WORK - WIRE BUNDLE W2514 - LACING TAPE INSTALLATION [Group 6, Configuration
2 ]  ................................................ 2 6 3
FIGURE 74: MORE WORK - RIGHT BODY FAIRING FEEDTHRU SEAL RING - GENERAL VISUAL
INSPECTION [Group 1-4, 7-8, Configuration 2] ....................... 2 6 7
FIGURE 75: MORE WORK - RIGHT BODY FAIRING FEEDTHRU SEAL RING - GENERAL VISUAL
INSPECTION [Group 6, Configuration 2] .......................... 2 6 9
FIGURE 76: MORE WORK - RIGHT BODY FAIRING FEEDTHRU SEAL RING - GENERAL VISUAL
INSPECTION [Group 5, Configuration 2] .......................... 2 7 1
FIGURE 77: BETWEEN P33 PANEL AND DISCONNECT BRACKET AD0880 - WIRE BUNDLE W4236 -
INSTALLATION [Group 7, Configuration 1] ......................... 2 7 3
FIGURE 78: BETWEEN P33 PANEL AND DISCONNECT BRACKET AD0880 - WIRE BUNDLE W4236 -
INSTALLATION [Group 8, Configuration 1] ......................... 2 7 6
FIGURE 79: MORE WORK - RIGHT BODY FAIRING WIRE BUNDLE W2514 - GENERAL VISUAL
INSPECTION [Group 1-3, 7-8, Configuration 2] ....................... 2 7 9
FIGURE 80: MORE WORK - RIGHT BODY FAIRING WIRE BUNDLE W2514 - GENERAL VISUAL
INSPECTION [Group 4, Configuration 2] .......................... 2 8 1
FIGURE 81: MORE WORK - WIRE BUNDLE W4236 GROUND - CHANGE [Group 5, Configuration 2] . 283
FIGURE 82: MORE WORK - WIRE BUNDLE W4236 GROUND - WIRING CHANGE [Group 5, Configuration
2 ]  ................................................ 2 8 5
APPENDIX A: OPERATIONAL TEST [Group 1-8, Configuration 1] .................... 2 8 6
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: November 16, 2023
757-29A0071 RBRevision 1: May 28, 2026
6 of 286
REQUIREMENTS BULLETIN 757-29A0071
ALERTALERT

### Page 7

Commercial 
Airplanes
757
Requirements Bulletin
ALERT
Revision Transmittal SheetNumber: 757-29A0071 RBOriginal Issue: November 16, 2023
Revision 1: May 28, 2026
ATA System: 2922
SUBJECT: HYDRAULIC POWER - Hydraulic Power Transfer Unit System - Relay Installation and
Wire Bundle Replacement
This revision includes all pages of the requirements bulletin.
COMPLIANCE INFORMATION RELATED TO THIS REVISION
Federal Aviation Administration (FAA) Airworthiness Directive AD 2024-25-09 is related to Requirements Bulletin
757-29A0071 RB. The effective date of AD 2024-25-09 is February 14, 2025.
The Federal Aviation Administration (FAA) will possibly release an additional Airworthiness Directive related to
Requirements Bulletin 757-29A0071 RB. The Airworthiness Directive will make the compliance tasks and times
given in Requirements Bulletin 757-29A0071 RB mandatory.
Airplanes NL001-NL002, NL006-NL017, NU701-NU705, NU721-NU728, and NU731-NU732 have been moved
from Group 1 to new Group 8 of this bulletin effectivity.
Airplanes NL101-NL109, NL141, and NL601-NL616 have been moved from Group 3 to new Group 7 of this
bulletin effectivity.
Effects of this Revision on airplanes on which the Original Issue was previously done:
ActionConditionGroup
Do Group 1-4, 7-8, Configura-
tion 2, More Work - Wire Bun-
dle Changes.
Airplanes that installed a wire bundle clamp with rubber
bushing(s) and straps on wire bundle W4236 in the un-
pressurized area, and installed a ground wire at a differ-
ent position on the ground panel. Airplanes that may not
have a seal ring at the right body fairing feedthru seal
installed.
1-4, 7-8
Airplanes that installed blue lacing tape or straps on wire
bundle W2514 in the unpressurized area and may not
have routed wire bundle W2514 through a clamp aft of
disconnect bracket AD0880.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: November 16, 2023
757-29A0071 RBRevision 1: May 28, 2026
7 of 286

### Page 8

ActionConditionGroup
Do Group 5, Configuration 2,
More Work - Wire Bundle
Changes.
Airplanes that installed straps on wire bundle W4236 and
blue lacing tape or straps on wire bundle W2514 in the
unpressurized area. Airplanes that may not have a seal
ring at the right body fairing feedthru seal installed,
5
Airplanes that installed a wire bundle W4236 ground wire
at a different position on the ground panel.
Do Group 6, Configuration 2,
More Work - Wire Bundle
Changes.
Airplanes that installed wire bundle clamps with rubber
bushing(s) and straps on wire bundle W4236, and blue
lacing tape or straps on wire bundle W2514 in the unpres-
surized area. Airplanes that may not have a seal ring at
the right body fairing feedthru seal installed.
6
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: November 16, 2023
757-29A0071 RBRevision 1: May 28, 2026
8 of 286
REQUIREMENTS BULLETIN 757-29A0071
ALERTALERT

### Page 9

ActionChange DescriptionGroupCondition
No action required.W4236 has been routed through
disconnect bracket AD0770.
3, 7Airplanes that have accom-
plished all applicable
changes in this table and
the changes were ap-
proved by the Boeing Orga-
nization Designation Autho-
rization (ODA) via a FAA
Form 8100-9
Existing clamp between STA 879
and STA 860 has been installed and
W4236 has been routed through the
butterfly clamp.
1-5, 7-8
Connector D43412J has been in-
stalled on AD0880 POS 3 or POS
11.
1-4, 7-8
Ground strap installed for GD05486S
has been installed within 6 inches
from the end of the overbraid sleev-
ing.
1-2, 4, 8
Ground strap installed for GD3094S
has been installed within 6 inches
from the end of the overbraid sleev-
ing.
3, 7
Instances of seal ring BACS11BD1
have been replaced with
BACS11BD5 OR BACS11BD6 in the
RIGHT BODY FAIRING
FEEDTHRU. Instances of sealant
BMS 5-45 Class B-1/2 and B-2 have
been replaced with sealant BMS 5-
37 B-1/2 or B-2 in the RIGHT BODY
FAIRING FEEDTHRU.
1-6, 7-8
Clamp support after passing through
AD0880 has been identified.
1-4, 7-8
W2514 routing between disconnect
bracket AD0880 and power transfer
control valve has white lacing tape
installed. Plastic tie straps in unpres-
surized areas on W2514 have been
removed.
1-6, 7-8
W4236 has been routed through the
extended fuselage.
7-8
Instances of rubber bushing clamps
in unpressurized areas on W2514
have been replaced.
1-4, 6-8
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: November 16, 2023
757-29A0071 RBRevision 1: May 28, 2026
9 of 286
REQUIREMENTS BULLETIN 757-29A0071
ALERTALERT

### Page 10

REASON FOR REVISION
This revision is sent to correct errors found during the accomplishment of this service bulletin. 757-300 airplanes
are moved from the existing Groups 1 and 3 to new Groups 7 and 8 because of the differences in the W4236
wire bundle routing for the extended fuselage. New Figures 49 through 55 have been added for Groups 3 and
7 airplanes. In Figures 11 and 32, wire bundle W4236, airplanes that have an existing clamp installed at a
standoff location between STA 879 and STA 860, an alternative clamp and hardware configuration has been
added. In Figures 8, 22 and 29, the alternate routing option for the bundle W4236 between STA 660 and STA
720 has been removed because there is only one route in this location.
On wire bundle W2514, instructions were given to use wire separation code blue lacing tape and straps between
disconnect bracket AD0880/AD0881 and the power transfer unit control valve. Wire bundle W2514 is routed
adjacent to existing wire bundles which have wire separation code green lacing tape installed. Instructions are
given to use white lacing tape, and not blue lacing tape in this area. Also, straps are not permitted in unpressurized
areas. Therefore, the use of straps has been removed for wire bundle W2514. In Figures 14, 18 and 24, aft of
disconnect bracket AD0880 a missing clamp location for wire bundle W2514 routing has been added.
On wire bundle W4236, instructions were given to install wire separation code blue lacing tape and straps. It is
not permitted to use straps in unpressurized areas. As a result, a footnote has been added to state that the use
of straps must only be installed in pressurized areas. For some airplanes, it was found that connector D43412
could not be installed at the selected position of the disconnect bracket AD0880/AD0881, because the bracket
cutout was too large for the connector. The connector position information has been changed. It was found that
a ground stud location did not comply with the SWPM requirements for the maximum distance of the ground to
be installed from the end of the overbraid sleeving. As a result, for Groups 1, 2, 4, 5 and 8 wire bundle W4236
ground wire has been moved to a different ground stud, and the identification of the ground has been changed.
For Groups 3 and 7, the ground stud location has been changed but the identification stays the same.
In Figures 10, 31 and 44, it was found that a seal ring could not be installed correctly onto the new seal. New
seal ring part numbers have been added. Also, the use of BMS 5-45 sealant has been replaced with BMS 5-37
sealant with the option of BMS 5-45 sealant, because BMS 5-45 is difficult to remove if future work is necessary
in this seal. In Figures 12, 24 and 42 instructions were given to install wire bundle clamp(s) with rubber bushing(s)
in unpressurized areas. The use of rubber bushings in unpressurized areas is not permitted. The installation of
clamp(s) with rubber bushing(s) in unpressurized areas have been replaced by different clamps.
These sections were changed:
– Effectivity:
– Changed airplane applicability statement.
– Moved 757-300 airplanes from Group 1 to new Group 8.
– Moved 757-300 airplanes from Group 3 to new Group 7.
– Added Configuration 2 information.
– Compliance:
– Added and changed AD information
– Added group applicability.
– Added Configuration 2 tables.
– Approval, added Alternative Method of Compliance (AMOC) statement.
– General Information, added notes.
– Work Instructions:
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: November 16, 2023
757-29A0071 RBRevision 1: May 28, 2026
10 of 286
REQUIREMENTS BULLETIN 757-29A0071
ALERTALERT

### Page 11

– Added group applicability.
– Group 3, Configuration 1 table, changed information.
– Groups 7 and 8, Configuration 1, added tables.
– Added Configuration 2 tables.
– FIGURE 1 through FIGURE 48, changed group applicability.
– FIGURE 8:
– Deleted Sheet 9.
– Sheet 11, added typical information.
– Sheet 12, changed connector and ground stud position, and ground nomenclature.
– FIGURE 9:
– Sheet 1, added optional connector position, changed find numbers and ground nomenclature.
– Find number table, added parts, find numbers and footnotes.
– FIGURE 10, step table, changed seal ring and sealant part numbers.
– FIGURE 11 and FIGURE 32:
– Sheet 1, added alternative clamp configuration.
– Step table, added step. Changed and added footnotes.
– FIGURE 12:
– Sheet 1, changed wire routing, added optional connector position and removed rubber bushing.
– Step table, removed rubber bushing and changed clamp part number.
– FIGURE 14, sheet 1, changed wire routing information and connector position.
– FIGURE 15 and FIGURE 19:
– Sheet 1, added optional connector position. Changed and added find numbers.
– Find number table, added find number, changed lacing tape information and removed straps.
– FIGURE 16, step table, changed sealant part number.
– FIGURE 18, sheet 1, changed wire routing and added optional connector position.
– FIGURE 21, sheet 1, changed illustration.
– FIGURE 22:
– Deleted Sheet 9.
– Sheet 12, changed ground stud position and nomenclature, and ground wire routing.
– FIGURE 23 and FIGURE 30:
– Sheet 1, changed ground nomenclature. Changed and added find numbers.
– Find number table, added parts and footnotes.
– FIGURE 24:
– Sheet 1, removed rubber bushing and changed view information.
– Step table, removed rubber bushing and changed clamp part number.
– FIGURE 26, sheet 1, changed wire routing.
– FIGURE 27, FIGURE 36 and FIGURE 48, find number table, changed lacing tape information and removed
straps.
– FIGURE 29:
– Deleted sheets 7 and 9.
– Sheet 29, changed ground stud position and nomenclature.
– FIGURE 31 and FIGURE 44, step table, changed seal ring and sealant part numbers.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: November 16, 2023
757-29A0071 RBRevision 1: May 28, 2026
11 of 286
REQUIREMENTS BULLETIN 757-29A0071
ALERTALERT

### Page 12

– FIGURE 32, sheet 1, added alternative clamp configuration.
– FIGURE 33 and FIGURE 45, sheet 1, changed view information.
– FIGURE 42:
– Sheet 11, removed rubber bushing and changed circle notes.
– Step table, added parts and changed clamp part number.
– FIGURE 43, find number table, added footnotes. Added and changed footnote references.
– FIGURE 49 through FIGURE 82, added.
– APPENDIX A, added group applicability.
– Group 1-8:
No further action is required.
REVISION HISTORY
Service BulletinService BulletinRequirement BulletinRequirement Bulletin
757-29A0071757-29A0071757-29A0071 RB757-29A0071 RB
Issue DateIssue Date
November 16, 2023Original Issue:November 16, 2023Original Issue:
May 28, 2026Revision 1:May 28, 2026Revision 1:
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: November 16, 2023
757-29A0071 RBRevision 1: May 28, 2026
12 of 286
REQUIREMENTS BULLETIN 757-29A0071
ALERTALERT

### Page 13

Commercial 
Airplanes
757
Requirements Bulletin
ALERT
Number: 757-29A0071 RB
Original Issue: November 16, 2023
Revision 1: May 28, 2026
ATA System: 2922
SUBJECT: HYDRAULIC POWER - Hydraulic Power Transfer Unit System - Relay Installation and
Wire Bundle Replacement
THIS DOCUMENT IS SENT TO THE OPERATORS OF RECORD OF THE AIRPLANES SHOWN IN
EFFECTIVITY. IF AN AIRPLANE HAS BEEN LEASED OR SOLD, SEND THIS DOCUMENT TO THE NEW
OPERATOR. IF APPLICABLE SPARES HAVE BEEN SOLD, SEND THIS DOCUMENT TO THE NEW OWNER.
THIS IS AN ENHANCED REQUIRED FOR COMPLIANCE DOCUMENT. THE BOEING PROCESSES USED
TO CREATE THE SERVICE BULLETIN (SB) AND THE REQUIREMENTS BULLETIN (RB) ENSURE THAT
THE INFORMATION BETWEEN "RC START" AND "RC END" IN THE SB ARE IDENTICAL TO THE
INFORMATION IN THE SAME SECTIONS (COMPLIANCE, WORK INSTRUCTIONS…) OF THE RB WHICH
THE SB REFERS TO AS THE RELATED DOCUMENT.
1. Effectivity
A. Airplanes
This bulletin is applicable to 757-200, 757-200CB, 757-200PF, 757-300 Airplane(s), line number(s)
1-2, 5, 14-15, 42, 46, 56, 74-75, 80, 97, 101-102, 106, 111-115, 117, 123, 127, 130, 132, 139,
141, 143, 145, 147-151, 153, 155, 162-163, 165-167, 169, 173-174, 176, 178, 180-184, 186-187,
189, 191, 193, 195, 197, 199-200, 203-204, 208-209, 211-215, 218-221, 224-232, 235-239, 246,
248-250, 255-257, 259, 264-265, 267-268, 270-271, 273-275, 279, 281, 285, 287-288, 291-294,
298, 300-302, 306, 312, 314, 317-319, 322-323, 325-326, 330, 332-335, 339-345, 347-350,
353-355, 359-364, 369-372, 374, 376-379, 382-389, 392-395, 397-400, 402-404, 407, 409-412,
414-418, 421-422, 424-425, 429-430, 432-433, 435-443, 445-446, 448-449, 453, 455, 458-459,
461, 465-466, 470-478, 480-482, 485-486, 489, 493, 495-503, 506, 508, 510-516, 518-519, 521,
523, 525-528, 530-546, 548-549, 551-556, 558-559, 561-571, 573-575, 577-586, 588-590, 592-597,
599, 601-605, 607-619, 622-625, 627-683, 685-707, 709-717, 719, 721-780, 782-800, 802-834,
836-875, 877-888, 890-894, 896-1050 in 8 Group(s). Where the effectivity is presented with hyphens
between line numbers, the airplane applicability means "through" and "inclusive", e.g. line numbers
1-9 means line numbers 1 through 9 inclusive.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: November 16, 2023
757-29A0071 RBRevision 1: May 28, 2026
13 of 286

### Page 14

The Variable Numbers and Group Information for the applicable airplanes is given below.
DESCRIPTIONCONFIGURATIONGROUP
757-200, 757-200CB, 757-200PF Airplanes with a different wiring
configuration.
-1
Airplanes with a different wiring configuration that have not done
bulletin 757-29A0071 Original Issue as of the Revision 1 date of
Requirements Bulletin 757-29A0071 RB.
1
Airplanes with a different wiring configuration that have done bulletin
757-29A0071 Original Issue as of the Revision 1 date of
Requirements Bulletin 757-29A0071 RB.
2
757-200 Airplanes with a different wiring configuration.-2
Airplanes with a different wiring configuration that have not done
bulletin 757-29A0071 Original Issue as of the Revision 1 date of
Requirements Bulletin 757-29A0071 RB.
1
Airplanes with a different wiring configuration that have done bulletin
757-29A0071 Original Issue as of the Revision 1 date of
Requirements Bulletin 757-29A0071 RB.
2
757-200 Airplanes with a different wiring configuration.-3
Airplanes with a different wiring configuration that have not done
bulletin 757-29A0071 Original Issue as of the Revision 1 date of
Requirements Bulletin 757-29A0071 RB.
1
Airplanes with a different wiring configuration that have done bulletin
757-29A0071 Original Issue as of the Revision 1 date of
Requirements Bulletin 757-29A0071 RB.
2
757-200 Airplanes with a different wiring configuration.-4
Airplanes with a different wiring configuration that have not done
bulletin 757-29A0071 Original Issue as of the Revision 1 date of
Requirements Bulletin 757-29A0071 RB.
1
Airplanes with a different wiring configuration that have done bulletin
757-29A0071 Original Issue as of the Revision 1 date of
Requirements Bulletin 757-29A0071 RB.
2
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: November 16, 2023
757-29A0071 RBRevision 1: May 28, 2026
14 of 286
REQUIREMENTS BULLETIN 757-29A0071
ALERTALERT

### Page 15

DESCRIPTIONCONFIGURATIONGROUP
757-200 Airplanes with a different wiring configuration.-5
Airplanes with a different wiring configuration that have not done
bulletin 757-29A0071 Original Issue as of the Revision 1 date of
Requirements Bulletin 757-29A0071 RB.
1
Airplanes with a different wiring configuration that have done bulletin
757-29A0071 Original Issue as of the Revision 1 date of
Requirements Bulletin 757-29A0071 RB.
2
757-200 Airplane with a different wiring configuration.-6
Airplanes with a different wiring configuration that have not done
bulletin 757-29A0071 Original Issue as of the Revision 1 date of
Requirements Bulletin 757-29A0071 RB.
1
Airplanes with a different wiring configuration that have done bulletin
757-29A0071 Original Issue as of the Revision 1 date of
Requirements Bulletin 757-29A0071 RB.
2
757-300 Airplanes with a different wiring configuration.-7
Airplanes with a different wiring configuration that have not done
bulletin 757-29A0071 Original Issue as of the Revision 1 date of
Requirements Bulletin 757-29A0071 RB.
1
Airplanes with a different wiring configuration that have done bulletin
757-29A0071 Original Issue as of the Revision 1 date of
Requirements Bulletin 757-29A0071 RB.
2
757-300 Airplanes with a different wiring configuration.-8
Airplanes with a different wiring configuration that have not done
bulletin 757-29A0071 Original Issue as of the Revision 1 date of
Requirements Bulletin 757-29A0071 RB.
1
Airplanes with a different wiring configuration that have done bulletin
757-29A0071 Original Issue as of the Revision 1 date of
Requirements Bulletin 757-29A0071 RB.
2
Airplane Models:
757-200, 757-200CB, 757-200PF, 757-300
GroupVariable Number
6NA001
GroupVariable Number
5NA002
GroupVariable Number
5NA005
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: November 16, 2023
757-29A0071 RBRevision 1: May 28, 2026
15 of 286
REQUIREMENTS BULLETIN 757-29A0071
ALERTALERT

### Page 16

GroupVariable Number
2NA021
4NA022 - NA028
4NA195
4NA197 - NA199
5NA205
4NA227 - NA228
4NA230
4NA235 - NA239
4NA301 - NA305
4NA343 - NA344
4NA346 - NA352
4NA392 - NA399
5NA401
2NA404
4NA406
4NA441 - NA447
1NA505
1NA519 - NA522
1NA549 - NA552
1NA554 - NA555
1NA558 - NA576
1NA578 - NA586
1NB023
1NB037
1NB041
1NB053
1NB062 - NB066
1NB070 - NB073
1NB079
1NB131 - NB148
1NB161 - NB162
1NB167 - NB168
4NB201 - NB202
GroupVariable Number
4NB221 - NB228
4NB230
4NB236
4NB239
1NB261 - NB267
1NB291 - NB299
1NB301 - NB302
1NB311 - NB312
1NB321 - NB330
1NB421
1NB424
1NB428 - NB431
1NB434 - NB435
1NB437 - NB438
1NB446
1NB451 - NB454
1NB501 - NB523
1NB571
1NB581 - NB583
1NC042
1NC051 - NC052
1NC056 - NC062
1NC066 - NC084
1NC091 - NC094
1NC151
1NC161
1NC901 - NC951
1NC971
1NC973 - NC974
1ND004
1ND012
1ND017
1ND032
GroupVariable Number
1ND039 - ND041
1ND044
1ND046
1ND048
1ND052 - ND053
1ND111
1ND113
1ND161
1ND163 - ND166
1ND169 - ND176
1ND178 - ND188
1ND190 - ND199
1ND201 - ND202
1ND221 - ND225
1ND241 - ND242
1ND244 - ND247
1ND301 - ND322
1ND401
1ND895
1NE001 - NE003
1NE008
1NE012
1NE017
1NE021 - NE022
1NE025
1NE029
1NE031
1NE036 - NE037
1NE040 - NE041
1NE044
1NE048 - NE051
1NE054 - NE055
1NE067 - NE075
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: November 16, 2023
757-29A0071 RBRevision 1: May 28, 2026
16 of 286
REQUIREMENTS BULLETIN 757-29A0071
ALERTALERT

### Page 17

GroupVariable Number
1NE077 - NE081
1NE083 - NE088
1NE092 - NE094
1NE145
1NE147
1NE161 - NE164
1NE166
1NE168
1NE170 - NE172
1NE174 - NE176
1NE201
1NE204
1NE301
1NE311 - NE325
3NJ001 - NJ004
3NJ031 - NJ032
3NJ551 - NJ555
8NL001 - NL002
8NL006 - NL017
7NL101 - NL109
7NL141
GroupVariable Number
7NL601 - NL616
1NN001 - NN002
1NN051 - NN052
1NP901 - NP904
1NS601 - NS616
1NT001 - NT009
1NT201 - NT202
4NT231 - NT234
4NT237 - NT238
1NT239 - NT240
1NT242
1NT245 - NT248
1NT281 - NT284
1NT286 - NT289
1NT341 - NT343
1NT345 - NT347
1NT351 - NT360
1NT371 - NT373
1NT375 - NT379
4NT381 - NT386
1NT401 - NT409
GroupVariable Number
1NT411 - NT412
1NT426 - NT427
1NT431 - NT432
1NT436 - NT438
1NT441 - NT442
1NT446
1NT701 - NT750
1NT752 - NT769
1NT791 - NT796
1NT861 - NT862
1NT881
1NT884 - NT885
1NT901 - NT903
1NT905 - NT916
1NT971 - NT985
1NU031 - NU038
8NU701 - NU705
8NU721 - NU728
8NU731 - NU732
--
--
B. Spares Affected
None.
2. CONCURRENT REQUIREMENTS
None.
3. COMPLIANCE
Federal Aviation Administration (FAA) Airworthiness Directive AD 2024-25-09 is related to Requirements
Bulletin 757-29A0071 RB. The effective date of AD 2024-25-09 is February 14, 2025.
The Federal Aviation Administration (FAA) will possibly release an additional Airworthiness Directive related
to Requirements Bulletin 757-29A0071 RB. The Airworthiness Directive will make the compliance tasks
and times given in Requirements Bulletin 757-29A0071 RB mandatory.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: November 16, 2023
757-29A0071 RBRevision 1: May 28, 2026
17 of 286
REQUIREMENTS BULLETIN 757-29A0071
ALERTALERT

### Page 18

When more than one OPTION is given for a CONDITION, do only one of the OPTION numbers. When
more than one ACTION is given for a CONDITION or an OPTION, do all of the ACTION numbers for that
CONDITION or OPTION.
Accomplish the required action(s), based on the applicable condition(s) in Table(s) 1 through 6, in accordance
with Accomplishment Instructions.
Group 1-2, 4-5, 8, Configuration 1:
Table 1: P33 Panel Relays Installation and Wire Bundle Changes
Repeat Interval
(Not to Exceed)
Boeing Recommended Compliance
Time (Whichever Occurs First)
ActionCondition
-Within 30 months
after the Revision 1
date of Require-
ments Bulletin 757-
29A0071 RB.
Within 2760 flight
cycles after the Re-
vision 1 date of Re-
quirements Bulletin
757-29A0071 RB.
ACTION 1: In the P33 panel, install
new relays, install new connector
and change wire bundle W1230.
All Airplanes
-ACTION 2: Install new connector
and change wire bundle W2360.
-ACTION 3: Install new connector
and change wire bundle W4236.
-ACTION 4: Install new connector
and change wire bundle W2514.
-ACTION 5: Do the Operational
Test. If the test fails, do applicable
corrective action(s) and repeat the
test until the test passes.
Group 3, 7, Configuration 1:
Table 2: P33 Panel Relays Installation and Wire Bundle Changes
Repeat Interval
(Not to Exceed)
Boeing Recommended Compliance
Time (Whichever Occurs First)
ActionCondition
-Within 30 months
after the Revision 1
date of Require-
ments Bulletin 757-
29A0071 RB.
Within 2760 flight
cycles after the Re-
vision 1 date of Re-
quirements Bulletin
757-29A0071 RB.
ACTION 1: In the P33 panel, install
new relays, install new connector
and change wire bundle W1230.
All Airplanes
-ACTION 2: Install new connector
and change wire bundle W2360.
-ACTION 3: Install new connector
and change wire bundles W5770,
W6670 and W4236.
-ACTION 4: Install new connector
and change wire bundle W2514.
-ACTION 5: Do the Operational
Test. If the test fails, do applicable
corrective action(s) and repeat the
test until the test passes.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: November 16, 2023
757-29A0071 RBRevision 1: May 28, 2026
18 of 286
REQUIREMENTS BULLETIN 757-29A0071
ALERTALERT

### Page 19

Group 6, Configuration 1:
Table 3: P33 Panel Relays Installation and Wire Bundle Changes
Repeat Interval
(Not to Exceed)
Boeing Recommended Compliance
Time (Whichever Occurs First)
ActionCondition
-Within 30 months
after the Revision 1
date of Require-
ments Bulletin 757-
29A0071 RB.
Within 2760 flight
cycles after the Re-
vision 1 date of Re-
quirements Bulletin
757-29A0071 RB.
ACTION 1: In the P33 panel, install
new relays, install new connector
and change wire bundle W1230.
All Airplanes
-ACTION 2: Install new connector
and change wire bundle W2360.
-ACTION 3: Install new connector
and change wire bundles W1200,
W4010, W4058 and W4236.
-ACTION 4: Install new connector
and change wire bundle W2514.
-ACTION 5: Do the Operational
Test. If the test fails, do applicable
corrective action(s) and repeat the
test until the test passes.
Group 1-4, 7-8, Configuration 2:
Table 4: More Work - Wire Bundle Changes
Repeat Inter-
val (Not to Ex-
ceed)
Boeing Recommended Compli-
ance Time (Whichever Occurs
First)
ActionCondition
-Within 30
months after the
Revision 1 date
of Require-
ments Bulletin
757-29A0071
RB.
Within 2760
flight cycles af-
ter the Revision
1 date of Re-
quirements Bul-
letin 757-
29A0071 RB.
ACTION 1: On wire bundle
W4236, remove a wire bundle
clamp with rubber bushing(s) and
straps, and install a new clamp
and lacing tape.
All Airplanes
-ACTION 2: On wire bundle
W4236, change the position of a
ground wire.
-ACTION 3: On wire bundle
W2514, remove blue lacing tape
or straps and install white lacing
tape.
-ACTION 4: Do a General Visual
Inspection for correct wire bundle
W2514 routing through a clamp
aft of disconnect bracket AD0880.
-ACTION 5: Do a General Visual
Inspection for a missing seal ring
at the right body fairing feedthru
seal.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: November 16, 2023
757-29A0071 RBRevision 1: May 28, 2026
19 of 286
REQUIREMENTS BULLETIN 757-29A0071
ALERTALERT

### Page 20

Group 1-4, 7-8, Configuration 2:
Table 4: More Work - Wire Bundle Changes
Repeat Inter-
val (Not to Ex-
ceed)
Boeing Recommended Compli-
ance Time (Whichever Occurs
First)
ActionCondition
---No further action required.CONDITION 1: COR-
RECT WIRE ROUTING
AND SEAL RING IN-
STALLATION FOUND.
--Before further
flight.
Correctly route W2514 through
the clamp aft of disconnect
bracket AD0880.
CONDITION 2: INCOR-
RECT WIRE ROUTING
FOUND.
--Before further
flight.
Install seal ring P/N BACS11BD5
OR P/N BACS11BD6 at the right
body fairing feedthru seal.
CONDITION 3: MISS-
ING SEAL RING
FOUND.
Group 5, Configuration 2:
Table 5: More Work - Wire Bundle Changes
Repeat Inter-
val (Not to Ex-
ceed)
Boeing Recommended Compli-
ance Time (Whichever Occurs
First)
ActionCondition
-Within 30
months after the
Revision 1 date
of Require-
ments Bulletin
757-29A0071
RB.
Within 2760
flight cycles af-
ter the Revision
1 date of Re-
quirements Bul-
letin 757-
29A0071 RB.
ACTION 1: On wire bundle
W4236, remove straps, and install
lacing tape.
All Airplanes
-ACTION 2: On wire bundle
W4236, change the position of a
ground wire.
-ACTION 3: On wire bundle
W2514, remove blue lacing tape
or straps and install white lacing
tape.
-ACTION 4: Do a General Visual
Inspection for a missing seal ring
at the right body fairing feedthru
seal.
---No further action required.CONDITION 4: SEAL
RING INSTALLATION
FOUND.
--Before further
flight.
Install seal ring P/N BACS11BD5
OR P/N BACS11BD6 at the right
body fairing feedthru seal.
CONDITION 5: MISS-
ING SEAL RING
FOUND.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: November 16, 2023
757-29A0071 RBRevision 1: May 28, 2026
20 of 286
REQUIREMENTS BULLETIN 757-29A0071
ALERTALERT

### Page 21

Group 6, Configuration 2:
Table 6: More Work - Wire Bundle Changes
Repeat Inter-
val (Not to Ex-
ceed)
Boeing Recommended Compli-
ance Time (Whichever Occurs
First)
ActionCondition
-Within 30
months after the
Revision 1 date
of Require-
ments Bulletin
757-29A0071
RB.
Within 2760
flight cycles af-
ter the Revision
1 date of Re-
quirements Bul-
letin 757-
29A0071 RB.
ACTION 1: On wire bundle
W4236, remove wire bundle
clamps with rubber bushing(s)
and straps, and install new
clamps and lacing tape.
All Airplanes
-ACTION 2: On wire bundle
W2514, remove blue lacing tape
or straps and install white lacing
tape.
-ACTION 3: Do a General Visual
Inspection for a missing seal ring
at the right body fairing feedthru
seal.
---No further action required.CONDITION 6: SEAL
RING INSTALLATION
FOUND.
--Before further
flight.
Install seal ring P/N BACS11BD5
OR P/N BACS11BD6 at the right
body fairing feedthru seal.
CONDITION 7: MISS-
ING SEAL RING
FOUND.
4. APPROVAL
This Requirements Bulletin was examined by the Federal Aviation Administration (FAA). The actions
specified in this document comply with the applicable regulations and are FAA approved, as well as European
Union Aviation Safety Agency (EASA) approved for all EASA approved airplanes listed in this Requirements
Bulletin effectivity. This document and its approval were based on the airplane in its original Boeing delivery
configuration or as modified by other Boeing changes.
If an airplane has a non-Boeing modification or repair that affects a component or system also affected by
this Requirements Bulletin, the operator is responsible for obtaining appropriate regulatory agency approval
before incorporating this Requirements Bulletin.
In addition, the Manager of the FAA Continued Operational Safety Branch approves accomplishment of
the actions defined in Requirements Bulletin 757-29A0071 Revision 1 as an alternative method of compliance
to accomplishing the requirements of paragraph (g) of AD 2024-25-09. All provisions of AD 2024-25-09 that
are not specifically referenced in the above statement remain fully applicable and must be complied with
accordingly.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: November 16, 2023
757-29A0071 RBRevision 1: May 28, 2026
21 of 286
REQUIREMENTS BULLETIN 757-29A0071
ALERTALERT

### Page 22

Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: November 16, 2023
757-29A0071 RBRevision 1: May 28, 2026
22 of 286
REQUIREMENTS BULLETIN 757-29A0071
ALERTALERT
BLANK PAGE

### Page 23

5.    ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL INFORMATION
NOTE: 1. This is an Enhanced Required for Compliance document. There will be a separate
Service Bulletin (SB) and a separate Requirements Bulletin (RB). If an RB is mandated
by an Airworthiness Directive (AD), then all applicable requirements specified in the
RB must be done. For the related SB, some locations are marked RC Start and RC
End to identify the requirements that are restated from the RB. For the related SB,
the areas between RC Start and RC End, including sub-steps and any figures
identified between RC Start and RC End, must be done to comply with the AD.
Therefore, an Alternative Method of Compliance (AMOC) is required for any deviations
to steps between RC Start and RC End, including substeps and identified figures.
For the related SB, the steps not between RC Start and RC End may be deviated
from using accepted methods in accordance with the operator's maintenance or
inspection program without obtaining approval of an AMOC; this is provided that the
steps between RC Start and RC End, including sub-steps and identified figures, can
still be done as specified, and the airplane can be put back in an airworthy condition.
Figures not required for compliance are omitted from the RB.
2. This is an Enhanced Required for Compliance document. The Boeing processes
used to create the Service Bulletin (SB) and the Requirements Bulletin (RB) ensure
that the information between "RC Start" and "RC End" in the SB are identical to the
information in the same sections (Compliance, Work Instructions...) of the RB which
the SB refers to as the related document.
3. The compliance times for the actions in WORK INSTRUCTIONS are in Compliance.
4. Unless shown differently, these dimensions and tolerances are used:
– Linear dimensions are in inches
– Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus
or minus 0.03 inch
– Tolerance on rivet and bolt edge margin is plus or minus 0.05 inch
– Angular tolerance is plus or minus 2 degrees
– Hole dimensions for standard solid rivets and fasteners are in Structural Repair
Manual (SRM) Chapter 51
– Torque Values:
— Values for structural fasteners are given in 757 Structural Repair Manual,
Chapter 51.
— Values for airframe maintenance tasks are included in Chapter 20 of 757
Aircraft Maintenance Manual (AMM).
— Values for electrical maintenance tasks are included in Chapter 20 of
Standard Wiring Practices Manual (SWPM).
— Values for engine maintenance tasks are included in Chapter 70 of 757
Aircraft Maintenance Manual (AMM).
— Non-standard torque values for maintenance tasks are included in the
applicable installation step.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: November 16, 2023
757-29A0071 RBRevision 1: May 28, 2026
23 of 286
REQUIREMENTS BULLETIN 757-29A0071
ALERTALERT

### Page 24

5. These work instructions refer to procedures included in other Boeing documents.
When the words "refer to" are used and the operator has an accepted alternative
procedure, the accepted alternative procedure can be used. When the words "in
accordance with" are included in the instruction, the procedure in the Boeing document
must be used.
6. Where the work instructions include installation of a kept part, a new or serviceable
part with the same part number can be installed as an alternative to the kept part.
7. If it is necessary to remove more parts for access, you can remove those parts. If
you can get access without removing identified parts, it is not necessary to remove
all of the identified parts. Jacking and shoring limitations must be observed.
8. Use the approved fastener, process and material substitutions in accordance with
SRM Chapter 51.
9. Refer to the SWPM 20-10-11 and SWPM 20-10-12 for the wire installation procedures,
and SWPM 20-10-19 for the wire separation requirements, as accepted procedures.
10. The necessary conditions for selection of clamp type and size are included in SWPM
20-10-12. If any wire bundle support clamp specified in this service bulletin does not
make a correct fit on the wire bundle, refer to SWPM 20-10-12 as an accepted
procedure to select a clamp that fits correctly.
11. If the length of any fastener specified in this service bulletin does not meet installation
standards given in SRM Chapter 51, then a fastener of the same specification, or
an approved substitute, with a length which meets the installation standards given
in SRM Chapter 51 may be used. Refer to SOPM 20-50-01 for ADJUSTMENT OF
GRIP LENGTH and USE OF WASHERS as an accepted procedure.
12. Do not use any kept bolts, screws, nuts, or washers with damage that impairs fit,
form, or function. Refer to SOPM 20-50-01 GENERAL.
13. Use of colors in Figures is based on guidance from the ATA e-Business Program
(ATA) iSpec 2200.
14. Where the figures in the Accomplishment Instructions specify certain positions on
the P33 panel and disconnect bracket AD0880 or AD0881 for installing the connectors,
it is permitted to use any open position on the P33 panel or disconnect bracket
AD0880 or AD0881 for installing the connectors. In this case the connector
Identification (ID) tape must be changed to show the selected position (POS) number.
Refer to the SWPM 20-10-11 as an accepted procedure.
15. A General Visual Inspection is defined as: A visual examination of an interior or
exterior area, installation or assembly to detect obvious damage, failure or irregularity.
This level of inspection is made from within touching distance, unless otherwise
specified. A mirror may be necessary to enhance visual access to all exposed surfaces
in the inspection area. This level of inspection is made under normally available
lighting conditions such as daylight, hangar lighting, flashlight or drop-light and may
require removal or opening of access panels or doors. Stands, ladders or platforms
may be required to gain proximity to the area being checked. Basic cleaning may be
required to ensure appropriate visibility.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: November 16, 2023
757-29A0071 RBRevision 1: May 28, 2026
24 of 286
REQUIREMENTS BULLETIN 757-29A0071
ALERTALERT

### Page 25

B. WORK INSTRUCTIONS
Actions Required for Compliance
1. Requirements
Group 1, Configuration 1:
Table 1: P33 Panel Relays Installation and Wire Bundle Changes
Refer to the listed proce-
dures in SB 757-29A0071
Revision 1 or later ap-
proved revisions as an ac-
cepted procedure.
Method of ComplianceActionCondition
PART 1: Open Access.-ACTION 1: In the P33 panel, install
new relays, install new connector
and change wire bundle W1230.
All Airplanes
-FIGURE 1, FIGURE 2,
FIGURE 3, FIGURE 4
-FIGURE 5, FIGURE 6ACTION 2: Install new connector
and change wire bundle W2360.
-FIGURE 7, FIGURE 8,
FIGURE 9, FIGURE 10,
FIGURE 11, FIGURE 12
ACTION 3: Install new connector
and change wire bundle W4236.
-FIGURE 13, FIGURE 14,
FIGURE 15, FIGURE 16
ACTION 4: Install new connector
and change wire bundle W2514.
-APPENDIX AACTION 5: Do the Operational
Test. If the test fails, do applicable
corrective action(s) and repeat the
test until the test passes.
PART 2: Close Access.-
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: November 16, 2023
757-29A0071 RBRevision 1: May 28, 2026
25 of 286
REQUIREMENTS BULLETIN 757-29A0071
ALERTALERT

### Page 26

Group 2, Configuration 1:
Table 2: P33 Panel Relays Installation and Wire Bundle Changes
Refer to the listed proce-
dures in SB 757-29A0071
Revision 1 or later ap-
proved revisions as an ac-
cepted procedure.
Method of ComplianceActionCondition
PART 1: Open Access.-ACTION 1: In the P33 panel, install
new relays, install new connector
and change wire bundle W1230.
All Airplanes
-FIGURE 1, FIGURE 2,
FIGURE 3, FIGURE 4
-FIGURE 5, FIGURE 6ACTION 2: Install new connector
and change wire bundle W2360.
-FIGURE 7, FIGURE 8,
FIGURE 9, FIGURE 10,
FIGURE 11, FIGURE 12
ACTION 3: Install new connector
and change wire bundle W4236.
-FIGURE 17, FIGURE 18,
FIGURE 19, FIGURE 16
ACTION 4: Install new connector
and change wire bundle W2514.
-APPENDIX AACTION 5: Do the Operational
Test. If the test fails, do applicable
corrective action(s) and repeat the
test until the test passes.
PART 2: Close Access.-
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: November 16, 2023
757-29A0071 RBRevision 1: May 28, 2026
26 of 286
REQUIREMENTS BULLETIN 757-29A0071
ALERTALERT

### Page 27

Group 3, Configuration 1:
Table 3: P33 Panel Relays Installation and Wire Bundle Changes
Refer to the listed proce-
dures in SB 757-29A0071
Revision 1 or later ap-
proved revisions as an ac-
cepted procedure.
Method of ComplianceActionCondition
PART 1: Open Access.-ACTION 1: In the P33 panel, install
new relays, install new connector
and change wire bundle W1230.
All Airplanes
-FIGURE 1, FIGURE 2,
FIGURE 3, FIGURE 4
-FIGURE 5, FIGURE 6ACTION 2: Install new connector
and change wire bundle W2360.
-FIGURE 20, FIGURE 21,
FIGURE 54, FIGURE 55,
FIGURE 50, FIGURE 10,
FIGURE 51
ACTION 3: Install new connector
and change wire bundles W5770,
W6670 and W4236.
-FIGURE 13, FIGURE 52,
FIGURE 53, FIGURE 16
ACTION 4: Install new connector
and change wire bundle W2514.
-APPENDIX AACTION 5: Do the Operational
Test. If the test fails, do applicable
corrective action(s) and repeat the
test until the test passes.
PART 2: Close Access.-
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: November 16, 2023
757-29A0071 RBRevision 1: May 28, 2026
27 of 286
REQUIREMENTS BULLETIN 757-29A0071
ALERTALERT

### Page 28

Group 4, Configuration 1:
Table 4: P33 Panel Relays Installation and Wire Bundle Changes
Refer to the listed proce-
dures in SB 757-29A0071
Revision 1 or later ap-
proved revisions as an ac-
cepted procedure.
Method of ComplianceActionCondition
PART 1: Open Access.-ACTION 1: In the P33 panel, install
new relays, install new connector
and change wire bundle W1230.
All Airplanes
-FIGURE 1, FIGURE 2,
FIGURE 3, FIGURE 4
-FIGURE 5, FIGURE 6ACTION 2: Install new connector
and change wire bundle W2360.
-FIGURE 7, FIGURE 22,
FIGURE 23, FIGURE 10,
FIGURE 11, FIGURE 24
ACTION 3: Install new connector
and change wire bundle W4236.
-FIGURE 25, FIGURE 26,
FIGURE 27, FIGURE 16
ACTION 4: Install new connector
and change wire bundle W2514.
-APPENDIX AACTION 5: Do the Operational
Test. If the test fails, do applicable
corrective action(s) and repeat the
test until the test passes.
PART 2: Close Access.-
Group 5, Configuration 1:
Table 5: P33 Panel Relays Installation and Wire Bundle Changes
Refer to the listed proce-
dures in SB 757-29A0071
Revision 1 or later ap-
proved revisions as an ac-
cepted procedure.
Method of ComplianceActionCondition
PART 1: Open Access.-ACTION 1: In the P33 panel, install
new relays, install new connector
and change wire bundle W1230.
All Airplanes
-FIGURE 1, FIGURE 2,
FIGURE 3, FIGURE 4
-FIGURE 5, FIGURE 6ACTION 2: Install new connector
and change wire bundle W2360.
-FIGURE 28, FIGURE 29,
FIGURE 30, FIGURE 31,
FIGURE 32, FIGURE 33
ACTION 3: Install new connector
and change wire bundle W4236.
-FIGURE 34, FIGURE 35,
FIGURE 36, FIGURE 16
ACTION 4: Install new connector
and change wire bundle W2514.
-APPENDIX AACTION 5: Do the Operational
Test. If the test fails, do applicable
corrective action(s) and repeat the
test until the test passes.
PART 2: Close Access.-
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: November 16, 2023
757-29A0071 RBRevision 1: May 28, 2026
28 of 286
REQUIREMENTS BULLETIN 757-29A0071
ALERTALERT

### Page 29

Group 6, Configuration 1:
Table 6: P33 Panel Relays Installation and Wire Bundle Changes
Refer to the listed proce-
dures in SB 757-29A0071
Revision 1 or later ap-
proved revisions as an ac-
cepted procedure.
Method of ComplianceActionCondition
PART 1: Open Access.-ACTION 1: In the P33 panel, install
new relays, install new connector
and change wire bundle W1230.
All Airplanes
-FIGURE 1, FIGURE 37,
FIGURE 38, FIGURE 4
-FIGURE 5, FIGURE 6ACTION 2: Install new connector
and change wire bundle W2360.
-FIGURE 39, FIGURE 40,
FIGURE 41, FIGURE 42,
FIGURE 43, FIGURE 44,
FIGURE 45
ACTION 3: Install new connector
and change wire bundles W1200,
W4010, W4058 and W4236.
-FIGURE 46, FIGURE 47,
FIGURE 48, FIGURE 16
ACTION 4: Install new connector
and change wire bundle W2514.
-APPENDIX AACTION 5: Do the Operational
Test. If the test fails, do applicable
corrective action(s) and repeat the
test until the test passes.
PART 2: Close Access.-
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: November 16, 2023
757-29A0071 RBRevision 1: May 28, 2026
29 of 286
REQUIREMENTS BULLETIN 757-29A0071
ALERTALERT

### Page 30

Group 7, Configuration 1:
Table 7: P33 Panel Relays Installation and Wire Bundle Changes
Refer to the listed proce-
dures in SB 757-29A0071
Revision 1 or later ap-
proved revisions as an ac-
cepted procedure.
Method of ComplianceActionCondition
PART 1: Open Access.-ACTION 1: In the P33 panel, install
new relays, install new connector
and change wire bundle W1230.
All Airplanes
-FIGURE 1, FIGURE 2,
FIGURE 3, FIGURE 4
-FIGURE 5, FIGURE 6ACTION 2: Install new connector
and change wire bundle W2360.
-FIGURE 20, FIGURE 21,
FIGURE 54, FIGURE 49,
FIGURE 77, FIGURE 10,
FIGURE 51
ACTION 3: Install new connector
and change wire bundles W5770,
W6670 and W4236.
-FIGURE 13, FIGURE 52,
FIGURE 53, FIGURE 16
ACTION 4: Install new connector
and change wire bundle W2514.
-APPENDIX AACTION 5: Do the Operational
Test. If the test fails, do applicable
corrective action(s) and repeat the
test until the test passes.
PART 2: Close Access.-
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: November 16, 2023
757-29A0071 RBRevision 1: May 28, 2026
30 of 286
REQUIREMENTS BULLETIN 757-29A0071
ALERTALERT

### Page 31

Group 8, Configuration 1:
Table 8: P33 Panel Relays Installation and Wire Bundle Changes
Refer to the listed proce-
dures in SB 757-29A0071
Revision 1 or later ap-
proved revisions as an ac-
cepted procedure.
Method of ComplianceActionCondition
PART 1: Open Access.-ACTION 1: In the P33 panel, install
new relays, install new connector
and change wire bundle W1230.
All Airplanes
-FIGURE 1, FIGURE 2,
FIGURE 3, FIGURE 4
-FIGURE 5, FIGURE 6ACTION 2: Install new connector
and change wire bundle W2360.
-FIGURE 7, FIGURE 56,
FIGURE 78, FIGURE 10,
FIGURE 11, FIGURE 12
ACTION 3: Install new connector
and change wire bundle W4236.
-FIGURE 13, FIGURE 14,
FIGURE 15, FIGURE 16
ACTION 4: Install new connector
and change wire bundle W2514.
-APPENDIX AACTION 5: Do the Operational
Test. If the test fails, do applicable
corrective action(s) and repeat the
test until the test passes.
PART 2: Close Access.-
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: November 16, 2023
757-29A0071 RBRevision 1: May 28, 2026
31 of 286
REQUIREMENTS BULLETIN 757-29A0071
ALERTALERT

### Page 32

Group 1, 8, Configuration 2:
Table 9: More Work - Wire Bundle Changes
Refer to the listed
procedures in SB
757-29A0071 Revi-
sion 1 or later ap-
proved revisions as
an accepted proce-
dure.
Method of Compli-
ance
ActionCondition
PART 3: More Work
Open Access.
-ACTION 1: On wire bundle W4236,
remove a wire bundle clamp with
rubber bushing(s) and straps, and
install a new clamp and lacing tape.
All Airplanes
-FIGURE 57, FIGURE
58
-FIGURE 59, FIGURE
60
ACTION 2: On wire bundle W4236,
change the position of a ground
wire.
-FIGURE 61ACTION 3: On wire bundle W2514
remove blue lacing tape or straps,
and install white lacing tape.
-FIGURE 79ACTION 4: Do a General Visual
Inspection for correct wire bundle
W2514 routing through a clamp aft
of disconnect bracket AD0880.
-FIGURE 74ACTION 5: Do a General Visual
Inspection for the installation of a
seal ring at the right body fairing
feedthru seal.
--No further action required.CONDITION 1: CORRECT
WIRE ROUTING AND
SEAL RING INSTALLA-
TION FOUND.
-FIGURE 79Correctly route W2514 through the
clamp aft of disconnect bracket
AD0880.
CONDITION 2: INCOR-
RECT WIRE ROUTING
FOUND.
-FIGURE 74Install seal ring P/N BACS11BD5
OR P/N BACS11BD6 at the right
body fairing feedthru seal.
CONDITION 3: MISSING
SEAL RING FOUND.
PART 4: More Work
Close Access.
--
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: November 16, 2023
757-29A0071 RBRevision 1: May 28, 2026
32 of 286
REQUIREMENTS BULLETIN 757-29A0071
ALERTALERT

### Page 33

Group 2, Configuration 2:
Table 10: More Work - Wire Bundle Changes
Refer to the listed
procedures in SB
757-29A0071 Revi-
sion 1 or later ap-
proved revisions as
an accepted proce-
dure.
Method of Compli-
ance
ActionCondition
PART 3: More Work
Open Access.
-ACTION 1: On wire bundle W4236,
remove a wire bundle clamp with
rubber bushing(s) and straps, and
install a new clamp and lacing tape.
All Airplanes
-FIGURE 57, FIGURE
58
-FIGURE 59, FIGURE
60
ACTION 2: On wire bundle W4236,
change the position of a ground
wire.
-FIGURE 62ACTION 3: On wire bundle W2514
remove blue lacing tape or straps,
and install white lacing tape.
-FIGURE 79ACTION 4: Do a General Visual
Inspection for correct wire bundle
W2514 routing through a clamp aft
of disconnect bracket AD0880.
-FIGURE 74ACTION 5: Do a General Visual
Inspection for the installation of a
seal ring at the right body fairing
feedthru seal.
--No further action required.CONDITION 1: CORRECT
WIRE ROUTING AND
SEAL RING INSTALLA-
TION FOUND.
-FIGURE 79Correctly route W2514 through the
clamp aft of disconnect bracket
AD0880.
CONDITION 2: INCOR-
RECT WIRE ROUTING
FOUND.
-FIGURE 74Install seal ring P/N BACS11BD5
OR P/N BACS11BD6 at the right
body fairing feedthru seal.
CONDITION 3: MISSING
SEAL RING FOUND.
PART 4: More Work
Close Access.
--
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: November 16, 2023
757-29A0071 RBRevision 1: May 28, 2026
33 of 286
REQUIREMENTS BULLETIN 757-29A0071
ALERTALERT

### Page 34

Group 3, 7, Configuration 2:
Table 11: More Work - Wire Bundle Changes
Refer to the listed
procedures in SB
757-29A0071 Revi-
sion 1 or later ap-
proved revisions as
an accepted proce-
dure.
Method of Compli-
ance
ActionCondition
PART 3: More Work
Open Access.
-ACTION 1: On wire bundle W4236,
remove a wire bundle clamp with
rubber bushing(s) and straps, and
install a new clamp and lacing tape.
All Airplanes
-FIGURE 57, FIGURE
63
-FIGURE 64, FIGURE
65
ACTION 2: On wire bundle W4236,
change the position of a ground
wire.
-FIGURE 61ACTION 3: On wire bundle W2514
remove blue lacing tape or straps,
and install white lacing tape.
-FIGURE 79ACTION 4: Do a General Visual
Inspection for correct wire bundle
W2514 routing through a clamp aft
of disconnect bracket AD0880.
-FIGURE 74ACTION 5: Do a General Visual
Inspection for the installation of a
seal ring at the right body fairing
feedthru seal.
--No further action required.CONDITION 1: CORRECT
WIRE ROUTING AND
SEAL RING INSTALLA-
TION FOUND.
-FIGURE 79Correctly route W2514 through the
clamp aft of disconnect bracket
AD0880.
CONDITION 2: INCOR-
RECT WIRE ROUTING
FOUND.
-FIGURE 74Install seal ring P/N BACS11BD5
OR P/N BACS11BD6 at the right
body fairing feedthru seal.
CONDITION 3: MISSING
SEAL RING FOUND.
PART 4: More Work
Close Access.
--
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: November 16, 2023
757-29A0071 RBRevision 1: May 28, 2026
34 of 286
REQUIREMENTS BULLETIN 757-29A0071
ALERTALERT

### Page 35

Group 4, Configuration 2:
Table 12: More Work - Wire Bundle Changes
Refer to the listed
procedures in SB
757-29A0071 Revi-
sion 1 or later ap-
proved revisions as
an accepted proce-
dure.
Method of Compli-
ance
ActionCondition
PART 3: More Work
Open Access.
-ACTION 1: On wire bundle W4236,
remove a wire bundle clamp with
rubber bushing(s) and straps, and
install a new clamp and lacing tape.
All Airplanes
-FIGURE 66, FIGURE
67
-FIGURE 59, FIGURE
60
ACTION 2: On wire bundle W4236,
change the position of a ground
wire.
-FIGURE 68ACTION 3: On wire bundle W2514
remove blue lacing tape or straps,
and install white lacing tape.
-FIGURE 80ACTION 4: Do a General Visual
Inspection for correct wire bundle
W2514 routing through a clamp aft
of disconnect bracket AD0880.
-FIGURE 74ACTION 4: Do a General Visual
Inspection for the installation of a
seal ring at the right body fairing
feedthru seal.
--No further action required.CONDITION 1: CORRECT
WIRE ROUTING AND
SEAL RING INSTALLA-
TION FOUND.
-FIGURE 80Correctly route W2514 through the
clamp aft of disconnect bracket
AD0880.
CONDITION 2: INCOR-
RECT WIRE ROUTING
FOUND.
-FIGURE 74Install seal ring P/N BACS11BD5
OR P/N BACS11BD6 at the right
body fairing feedthru seal.
CONDITION 3: MISSING
SEAL RING FOUND.
PART 4: More Work
Close Access.
--
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: November 16, 2023
757-29A0071 RBRevision 1: May 28, 2026
35 of 286
REQUIREMENTS BULLETIN 757-29A0071
ALERTALERT

### Page 36

Group 5, Configuration 2:
Table 13: More Work - Wire Bundle Changes
Refer to the listed
procedures in SB
757-29A0071 Revi-
sion 1 or later ap-
proved revisions as
an accepted proce-
dure.
Method of Compli-
ance
ActionCondition
PART 3: More Work
Open Access.
-ACTION 1: On wire bundle W4236,
remove straps, and install lacing
tape.
All Airplanes
-FIGURE 69
-FIGURE 81, FIGURE
82
ACTION 2: On wire bundle W4236,
change the position of a ground
wire.
-FIGURE 70ACTION 3: On wire bundle W2514
remove blue lacing tape or straps,
and install white lacing tape.
-FIGURE 76ACTION 4: Do a General Visual
Inspection for the installation of a
seal ring at the right body fairing
feedthru seal.
--No further action required.CONDITION 4: SEAL RING
INSTALLATION FOUND.
-FIGURE 76Install seal ring P/N BACS11BD5
OR P/N BACS11BD6 at the right
body fairing feedthru seal.
CONDITION 5: MISSING
SEAL RING FOUND.
PART 4: More Work
Close Access.
--
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: November 16, 2023
757-29A0071 RBRevision 1: May 28, 2026
36 of 286
REQUIREMENTS BULLETIN 757-29A0071
ALERTALERT

### Page 37

Group 6, Configuration 2:
Table 14: More Work - Wire Bundle Changes
Refer to the listed
procedures in SB
757-29A0071 Revi-
sion 1 or later ap-
proved revisions as
an accepted proce-
dure.
Method of Compli-
ance
ActionCondition
PART 3: More Work
Open Access.
-ACTION 1: On wire bundle W4236,
remove wire bundle clamps with
rubber bushing(s) and straps, and
install new clamps and lacing tape.
All Airplanes
-FIGURE 71, FIGURE
72
-FIGURE 73ACTION 2: On wire bundle W2514
remove blue lacing tape or straps,
and install white lacing tape.
-FIGURE 75ACTION 3: Do a General Visual
Inspection for the installation of a
seal ring at the right body fairing
feedthru seal.
--No further action required.CONDITION 6: SEAL RING
INSTALLATION FOUND.
-FIGURE 75Install seal ring P/N BACS11BD5
OR P/N BACS11BD6 at the right
body fairing feedthru seal.
CONDITION 7: MISSING
SEAL RING FOUND.
PART 4: More Work
Close Access.
--
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: November 16, 2023
757-29A0071 RBRevision 1: May 28, 2026
37 of 286
REQUIREMENTS BULLETIN 757-29A0071
ALERTALERT

### Page 38 (OCR)

REQUIREMENTS BULLETIN 757-29A0071
ALERT  ALERT
This Figure applies only to: Group 1-8, Configuration 1.
STA
377.7
STA
377.7
MAIN EQUIPMENT CENTER
P33 PANEL
FWD
K10873
A-A  2992509
FIGURE 1: P33 PANEL - RELAYS K10902 AND K10904 - INSTALLATION
(SHEET 1 OF 2)
Original Issue: November 16, 2023
Revision 1 May 28, 2026  757-29A0071 RB
Export Controlled ECCN: 9E991
See page 1 for details  38 of 286

### Page 39

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for each airplane.
More DataQtyIdentificationNameTaskStep
(a)2BACS16X1ARELAY SOCKETInstall (New)1
(a)2BACR13CF2ARELAYInstall (New)2
(b)1284N1211-3BRADY DECAL, K10904Install (New)3
(b)1284N1211-2BRADY DECAL, K10902Install (New)4
(a) Refer to SWPM 20-81-22 as an accepted procedure.
(b) Refer to SOPM 20-50-05, Type F as an accepted procedure.
FIGURE 1: P33 PANEL - RELAYS K10902 AND K10904 - INSTALLATION
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: November 16, 2023
757-29A0071 RBRevision 1 May 28, 2026
39 of 286
REQUIREMENTS BULLETIN 757-29A0071
ALERTALERT

### Page 40

This Figure applies only to: Group 1-5, 7-8, Configuration 1.
FIGURE 2: P33 PANEL - WIRE BUNDLE W1230 - WIRE ROUTING
(SHEET 1 OF 2)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: November 16, 2023
757-29A0071 RBRevision 1 May 28, 2026
40 of 286
REQUIREMENTS BULLETIN 757-29A0071
ALERTALERT

### Page 41

FIGURE 2: P33 PANEL - WIRE BUNDLE W1230 - WIRE ROUTING
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: November 16, 2023
757-29A0071 RBRevision 1 May 28, 2026
41 of 286
REQUIREMENTS BULLETIN 757-29A0071
ALERTALERT

### Page 42 (OCR)

REQUIREMENTS BULLETIN 757-29A0071
ALERT  ALERT
This Figure applies only to: Group 1-5, 7-8, Configuration 1.
W1230  3 LOCATIONS 1
2 LOCATIONS  > 3 LOCATIONS
A2  0471-16  G04  - 0479-16-  1 W2360
→ 9 LOCATIONS  TB46 6
A1  0472-16  3 W4236
Х1  0474-22
X2  0473-22
2 LOCATIONS  GD450-DC
D3134  5
K10902
PTU MOV CLOSE  10
• 2 LOCATIONS
A2  0475-16
A1  0476-16  W4236
Х1  0478-22
D43312P
X2  0477-22  POS 11
2 LOCATIONS  GD450-DC
5
D3138
K10904
PTU MOV OPEN
+ 0187-22 +
АЗ
АЗ  СЗ
A1  0188-22  70192-22+
A2  R10240 5  TB46A  J  D41950P
Х1  12  POS 19
X2
D3130
K10051
PTU ON RELAY
P33 MISC RELAY PANEL
ADDED WIRE OR NEW ROUTING  D  FIND NUMBER
+ DELETED WIRE OR FORMER ROUTING  EXISTING WIRE
FIGURE 3: P33 PANEL - WIRE BUNDLE W1230 - CHANGE
(SHEET 1 OF 3)
Original Issue: November 16, 2023
Revision 1 May 28, 2026  Export Controlled ECCN: 9E991  757-29A0071 RB
See page 1 for details  42 of 286

### Page 43

REFERENCE: 757 WDM 29-22-11
The find numbers (No.) shown below agree with the find number symbol in the figure.
More DataQtyIdentificationName
Find
No.
(a)3BACC47CN3SCONTACT1
(b)4BACC47DJ2CONTACT, SOCKET2
(b)5BACC47DJ1CONTACT, SOCKET3
(c)3BACC47DE5ACONTACT4
(c)(d)3BACC47DE4ACONTACT5
(e)1BACM15C1BTERMINAL BLOCK6
(a)1BACC45FN18-8PCONNECTOR, ELECTRICAL, RECEPTACLE,
FLANGE MOUNT, BAYONET COUPLING
7
(f)1280N3381-10201ID - EQUIPMENT9
(f)1280N3381-10202ID - EQUIPMENT10
(f)1280N3381-10203ID - EQUIPMENT11
(a)2MS27488-20-2PLUG END SEAL ELECTRICAL CONNECTOR12
(a)5MS27488-12-2PLUG, END SEAL13
(g)-280N3381-102WWIRE - RAW MATERIAL14
(h)-280N3381-1001LACING TAPE - BLUE - PRESSURIZED (TEMP 135
DEG)
(i)-BACS38K1STRAP
(i)-BACS38K4STRAP
(i)-BACS38K5STRAP
(a) Refer to SWPM 20-61-11 as an accepted procedure.
(b) Refer to SWPM 20-81-12 as an accepted procedure.
(c) Refer to SWPM 20-90-11 as an accepted procedure.
(d) Wire 0192-22 can be terminated at TB80, position YC10 instead of TB46A, position C3.
(e) Refer to SWPM 20-90-11 as an accepted procedure.
(f) Install within 6 inches of equipment.
(g) Refer to SWPM 20-10-11 as an accepted procedure.
(h) Refer to SWPM 20-10-11 and SWPM 20-10-19 as accepted procedures.
(i) Select the strap size to fit the wire bundle and install at 6 - 8 inch spacing intervals. Refer to SWPM 20-
10-11 as an accepted procedure.
FIGURE 3: P33 PANEL - WIRE BUNDLE W1230 - CHANGE
(SHEET 2 OF 3)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: November 16, 2023
757-29A0071 RBRevision 1 May 28, 2026
43 of 286
REQUIREMENTS BULLETIN 757-29A0071
ALERTALERT

### Page 44

WIRE LIST - CUT AND CODE AS REQUIRED
NOTESMATERIAL SPECIFICATIONLENGTH
(INCHES)
TYPE
CODE
GAGE
COLOR
WIRE
NUMBER
WIRE
BUNDLE
-BMS13-48T10C01G01696PA160471W1230
-BMS13-48T10C01G01696PA160472W1230
-BMS13-48T10C01G02296PA220473W1230
-BMS13-48T10C01G02296PA220474W1230
-BMS13-48T10C01G01696PA160475W1230
-BMS13-48T10C01G01696PA160476W1230
-BMS13-48T10C01G02296PA220477W1230
-BMS13-48T10C01G02296PA220478W1230
-BMS13-48T10C01G01696PA160479W1230
FIGURE 3: P33 PANEL - WIRE BUNDLE W1230 - CHANGE
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: November 16, 2023
757-29A0071 RBRevision 1 May 28, 2026
44 of 286
REQUIREMENTS BULLETIN 757-29A0071
ALERTALERT

### Page 45 (OCR)

REQUIREMENTS BULLETIN 757-29A0071
ALERT  ALERT
This Figure applies only to: Group 1-8, Configuration 1.
STA
377.7
STA
377.7
MAIN EQUIPMENT CENTER
D43312J
POS 11
2) 4 LOCATIONS
4 LOCATIONS 1
VIEW LOOKING UP
2993665
FIGURE 4: P33 PANEL - ELECTRICAL CONNECTOR D43312J - INSTALLATION
(SHEET 1 OF 2)
Original Issue: November 16, 2023
Revision 1 May 28, 2026  757-29A0071 RB
Export Controlled ECCN: 9E991
See page 1 for details  45 of 286

### Page 46

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for each airplane.
More DataQtyIdentificationNameTaskStep
(a)4BACS12HN04-8SCREWInstall (New)1
(a)4NAS1149DN416JWASHERInstall (New)
(a)4BACN10YR04CDNUTInstall (New)2
(a) Refer to SWPM 20-60-06 as an accepted procedure.
FIGURE 4: P33 PANEL - ELECTRICAL CONNECTOR D43312J - INSTALLATION
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: November 16, 2023
757-29A0071 RBRevision 1 May 28, 2026
46 of 286
REQUIREMENTS BULLETIN 757-29A0071
ALERTALERT

### Page 47 (OCR)

REQUIREMENTS BULLETIN 757-29A0071
ALERT  ALERT
_ This Figure applies only to: Group 1-8, Configuration 1.
STA
278
W2360
FLIGHT COMPARTMENT
P11-4
P11-3
TO:
C4054
P11-2
FWD  P11-1  2993100
P11 CIRCUIT BREAKER PANEL
FIGURE 5: BETWEEN P11 PANEL AND P33 PANEL - WIRE BUNDLE W2360 - WIRE ROUTING
(SHEET 1 OF 4)
Original Issue: November 16, 2023
Revision 1 May 28, 2026  757-29A0071 RB
Export Controlled ECCN: 9E991
See page 1 for details  47 of 286

### Page 48 (OCR)

REQUIREMENTS BULLETIN 757-29A0071
ALERT  ALERT
W2360
VIEW LOOKING UP
• W2360
RIGHT SIDE CAB
FIGURE 5: BETWEEN P11 PANEL AND P33 PANEL - WIRE BUNDLE W2360 - WIRE ROUTING
(SHEET 2 OF 4)
Original Issue: November 16, 2023
Revision 1 May 28, 2026  757-29A0071 RB
Export Controlled ECCN: 9E991
See page 1 for details  48 of 286

### Page 49 (OCR)

REQUIREMENTS BULLETIN 757-29A0071
ALERT  ALERT
W2360
STA
365.25
STA
377.7
2993142
FIGURE 5: BETWEEN P11 PANEL AND P33 PANEL - WIRE BUNDLE W2360 - WIRE ROUTING
(SHEET 3 OF 4)
Original Issue: November 16, 2023
Revision 1 May 28, 2026  757-29A0071 RB
Export Controlled ECCN: 9E991
See page 1 for details  49 of 286

### Page 50

FIGURE 5: BETWEEN P11 PANEL AND P33 PANEL - WIRE BUNDLE W2360 - WIRE ROUTING
(SHEET 4 OF 4)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: November 16, 2023
757-29A0071 RBRevision 1 May 28, 2026
50 of 286
REQUIREMENTS BULLETIN 757-29A0071
ALERTALERT

### Page 51

This Figure applies only to: Group 1-8, Configuration 1.
REFERENCE: 757 WDM 29-22-11
The find numbers (No.) shown below agree with the find number symbol in the figure.
More DataQtyIdentificationName
Find
No.
(a)1BACT12AC53TERMINAL, LUG1
(b)1BACC47CP3SCONTACT2
(b)1BACC45FT18-8SCONNECTOR, ELECTRICAL, PLUG,
STRAIGHT, BAYONET COUPLING
3
(c)1280N3381-10101ID - EQUIPMENT4
(b)5MS27488-12-2PLUG, END SEAL5
(d)-280N3381-101WWIRE - RAW MATERIAL6
(e)-280N3381-1001LACING TAPE - BLUE - PRESSURIZED (TEMP
135 DEG)
(f)-BACS38K1STRAP
(f)-BACS38K4STRAP
(f)-BACS38K5STRAP
(a) Refer to SWPM 20-30-11 as an accepted procedure.
(b) Refer to SWPM 20-61-11 as an accepted procedure.
(c) Install within 6 inches of equipment.
(d) Refer to SWPM 20-10-11 as an accepted procedure.
FIGURE 6: BETWEEN P11 PANEL AND P33 PANEL - WIRE BUNDLE W2360 - CHANGE
(SHEET 1 OF 2)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: November 16, 2023
757-29A0071 RBRevision 1 May 28, 2026
51 of 286
REQUIREMENTS BULLETIN 757-29A0071
ALERTALERT

### Page 52

More DataQtyIdentificationName
Find
No.
(e) Refer to SWPM 20-10-11 and SWPM 20-10-19 as accepted procedures.
(f) Select the strap size to fit the wire bundle and install at 6 - 8 inch spacing intervals. Refer to SWPM 20-
10-11 as an accepted procedure.
WIRE LIST - CUT AND CODE AS REQUIRED
NOTESMATERIAL SPECIFICATIONLENGTH
(INCHES)
TYPE
CODE
GAGE
COLOR
WIRE
NUMBER
WIRE
BUNDLE
-BMS13-48T10C01G014504PA140621W2360
FIGURE 6: BETWEEN P11 PANEL AND P33 PANEL - WIRE BUNDLE W2360 - CHANGE
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: November 16, 2023
757-29A0071 RBRevision 1 May 28, 2026
52 of 286
REQUIREMENTS BULLETIN 757-29A0071
ALERTALERT

### Page 53

This Figure applies only to: Group 1-2, 4, 8, Configuration 1.
REFERENCE: 757 WDM 29-22-11
DescriptionFlag Note
Alternatively, deleted wire(s) can be capped and stowed. Refer to SWPM 20-10-11 as
an accepted procedure.
A
Seal connector cavities of deleted wire or capped and stowed with Plug, End Seals.
Refer to SWPM 20-60-08 as an accepted procedure.
B
FIGURE 7: BETWEEN P33 PANEL AND DISCONNECT BRACKET AD1090 - WIRE BUNDLE W4236 -
REMOVAL
(SHEET 1 OF 1)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: November 16, 2023
757-29A0071 RBRevision 1 May 28, 2026
53 of 286
REQUIREMENTS BULLETIN 757-29A0071
ALERTALERT

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
