# Boeing Alert Service Bulletin 757-52A0091: Revision 1

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2013-0300; AD 2015-25-01 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Alert Service Bulletin 757-52A0091](https://openairdocs.org/service-documents/boeing/757-52a0091.md)
- Title as filed: U.S. DOT/FAA - SB-757-52A0091-01
- Pages: 62
- PDF: https://openairdocs.org/files/sha256/72/82/7282699837d8e208880bbf35406bbb3243e383a77fd72404ebaf6227387b758f
- Page: https://openairdocs.org/service-documents/boeing/757-52a0091/file/7282699837d8

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Commercial 
Airplanes
757
Service Bulletin
ALERT
Number: 757-52A0091
Original Issue: March 09, 2010
Revision 1: December 19, 2014
ATA System: 5232
SUBJECT: DOORS - Main Cargo Door - Cam Latch and Latch Pin Inspection and Modification
Export of this technology is controlled under the United States Export Administration Regulations (EAR) (15
CFR 300-774). An export license may be required before it is used for development, production or use by foreign
persons from specific countries. The controller of this data has the individual responsibility to abide by all export
laws.
9E991ECCN:
BOEING PROPRIETARY, CONFIDENTIAL AND/OR TRADE SECRET
Copyright © 2010 Boeing.
Unpublished Work. All Rights Reserved.
Treatment of this document and its content is governed by contract with Boeing. Rights to use this document
are licensed on a per aircraft basis and such rights may not be transferable. For more information, contact The
Boeing Company.
Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner,
BBJ, DC-8, DC-9, DC-10, KC-10, KC-46, KDC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8, Poseidon and
Boeing liveries are all trademarks owned by The Boeing Company; and no trademark license is granted in
connection with this document unless provided in writing by Boeing.
Original Issue: March 09, 2010
757-52A0091Revision 1: December 19, 2014
1 of 62
3.0

### Page 2

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: March 09, 2010
757-52A0091Revision 1: December 19, 2014
2 of 62
BOEING SERVICE BULLETIN 757-52A0091
ALERTALERT
BLANK PAGE

### Page 3

Table of Contents
Revision Transmittal Sheet ............................................ 5
Summary ...................................................... 7
1. PLANNING INFORMATION ........................................ 1 1
A. Effectivity ............................................... 1 1
1. Airplanes ............................................ 1 1
2. Spares Affected ........................................ 1 2
B. Concurrent Requirements ...................................... 1 2
C. Reason ................................................ 1 2
D. Description .............................................. 1 3
E. Compliance .............................................. 1 3
F. Approval ............................................... 2 4
G. Manpower .............................................. 2 5
H. Weight and Balance Changes .................................... 2 6
I. Electrical Load Data ......................................... 2 6
J. References .............................................. 2 6
1. Existing Data: ......................................... 2 6
2. Data Supplied with this Service Bulletin: ........................... 2 6
3. Installation Drawings Used in the Preparation of this Service Bulletin: ........... 2 6
K. Publications Affected ........................................ 2 7
L. Interchangeability and Intermixability of Parts ........................... 2 7
M. Software Accomplishment Summary ................................ 2 7
2. MATERIAL INFORMATION ........................................ 2 9
A. Material - Price and Availability ................................... 2 9
B. Industry Support Information .................................... 2 9
C. Parts Necessary for Each Airplane ................................. 2 9
1. Kits/Parts ............................................ 2 9
2. Parts and Materials Supplied by the Operator ........................ 2 9
3. Parts Modified and Reidentified ................................ 2 9
4. Parts Removed and Not Replaced .............................. 3 0
D. Parts Necessary to Change Spares ................................. 3 0
E. Special Tooling - Price and Availability ............................... 3 0
F. Special Tooling Necessary to do this Service Bulletin ....................... 3 0
3. ACCOMPLISHMENT INSTRUCTIONS .................................. 3 1
A. GENERAL INFORMATION ..................................... 3 1
B. WORK INSTRUCTIONS ....................................... 3 2
FIGURE 1: MAIN CARGO DOOR - CAM LATCHES AND LATCH PINS INSPECTION ......... 3 7
FIGURE 2: MAIN CARGO DOOR - LATCH PIN CROSS BOLT TORQUE ................ 4 0
FIGURE 3: MAIN CARGO DOOR - LATCH PIN EXTENSION MEASUREMENT ............ 4 2
FIGURE 4: MAIN CARGO DOOR - CAM LATCH 1 AND CAM LATCH 2 INSPECTION ........ 4 4
FIGURE 5: MAIN CARGO DOOR - LATCH PIN CROSS BOLT REPLACEMENT ........... 4 6
FIGURE 6: MAIN CARGO DOOR - CAM LATCH REPLACEMENT ................... 4 8
FIGURE 7: MAIN CARGO DOOR - LATCH PIN REPLACEMENT .................... 5 1
FIGURE 8: MAIN CARGO DOOR - CAM LATCH REMOVAL AND INSPECTION ........... 5 3
FIGURE 9: MAIN CARGO DOOR - CAM LATCHES, LATCH PINS AND LATCH PIN CROSS BOLTS
INSPECTION .......................................... 5 6
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: March 09, 2010
757-52A0091Revision 1: December 19, 2014
3 of 62
BOEING SERVICE BULLETIN 757-52A0091
ALERTALERT

### Page 4

FIGURE 10: MAIN CARGO DOOR - CAM LATCH AND LATCH PIN RIGGING ............. 5 8
FIGURE 11: MAIN CARGO DOOR - MAIN CARGO DOOR EDGE FLUSHNESS MEASUREMENT . . 61
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: March 09, 2010
757-52A0091Revision 1: December 19, 2014
4 of 62
BOEING SERVICE BULLETIN 757-52A0091
ALERTALERT

### Page 5

Commercial 
Airplanes
757
Service Bulletin
ALERT
Revision Transmittal SheetNumber: 757-52A0091Original Issue: March 09, 2010
Revision 1: December 19, 2014
ATA System: 5232
SUBJECT: DOORS - Main Cargo Door - Cam Latch and Latch Pin Inspection and Modification
This revision includes all pages of the service bulletin.
COMPLIANCE INFORMATION RELATED TO THIS REVISION
Federal Aviation Administration (FAA) Notice of Proposed Rule Making NPRM 2011-NM-163-AD, is related to
this service bulletin.
No more work is necessary on the airplane(s) changed or inspected in accordance with the original issue of this
service bulletin.
REASON FOR REVISION
This revision is sent to clarify the requirements of the compliance tables.
These sections were changed:
1. Summary
a. Background:
(1) Background statement revised and new service history information was added.
(2) Summary Evaluation Table added.
b. Action - Changed to agree with work instructions.
c. Compliance - NPRM statement added.
2. Planning Information
a. Reason - Added the reason for Revision 1 is sent to statement.
b. Description - Changed to agree with work instructions.
c. Compliance:
(1) NPRM statement added.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: March 09, 2010
757-52A0091Revision 1: December 19, 2014
5 of 62

### Page 6

(2) Compliance Tables 1 and 2 revised to clarify inspections, conditions and actions.
3. Accomplishment Instructions
a. General Information - Notes numbering has been changed and new notes added.
b. Work Instructions - Revised for clarification.
Vertical lines are put on the left edge of each page, except in Paragraph 1.A., Effectivity and format changes,
to show the location of all content changes.
Pages with no vertical lines have no changes.
REVISION HISTORY
March 09, 2010Original Issue:
December 19, 2014Revision 1:
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: March 09, 2010
757-52A0091Revision 1: December 19, 2014
6 of 62
BOEING SERVICE BULLETIN 757-52A0091
ALERTALERT

### Page 7

Commercial 
Airplanes
757
Service Bulletin
ALERT
SummaryNumber: 757-52A0091Original Issue: March 09, 2010
Revision 1: December 19, 2014
ATA System: 5232
SUBJECT: DOORS - Main Cargo Door - Cam Latch and Latch Pin Inspection and Modification
THIS BULLETIN IS SENT TO THE OPERATORS OF RECORD OF THE AIRPLANES SHOWN IN PARAGRAPH
1.A., EFFECTIVITY. IF AN AIRPLANE HAS BEEN LEASED OR SOLD, SEND THIS SERVICE BULLETIN TO
THE NEW OPERATOR. IF APPLICABLE SPARES HAVE BEEN SOLD, SEND THIS SERVICE BULLETIN TO
THE NEW OWNER.
CONCURRENT REQUIREMENTS
None.
BACKGROUND
Accomplishment of the inspections in this service bulletin will make sure the Main Cargo Door (MCD) cam latches
are inspected for damage and the latch pins are inspected for damage and migration. The inspections are
necessary in order to find and replace damaged cam latches, latch pins and latch pin cross bolts. If not replaced,
damaged cam latches, latch pins and latch pin cross bolts could lead to a failure of the cam latches and may
result in a possible rapid decompression and potential separation of the cargo door from the airplane.
Boeing has received one report from one operator that the MCD forward most cam latch on the forward center
cam latch pair (cam latch number 3) broke during flight. The airplane that reported the broken cam latch had
20,000 flight hours and 9,500 flight cycles when the cam latch broke. The crew heard a loud noise coming from
the MCD shortly after cruise. Upon landing, an inspection was performed and a cam latch was found broken.
The broken cam latch mating latch pin was also found to have significant wear as evidenced by the loss of the
plating on the surface that is normally in contact with the cam. The latch pin was also deformed approximately
0.05 inch in the area of the wear surface.
The cause of the broken cam latch has been determined to be from a poorly rigged MCD. Although rigged per
the original Aircraft Maintenance Manual (AMM) procedures, significant variation was allowed in the rigging
dimensions. This variation can cause some of the latch pin/cam latch locations to have a significant preload
placed on them during engagement and rotation of the cam latches during latching and unlatching operations.
This preload is believed to have imparted a torque on the latch pin from the cam latch rotation during latching
and unlatching operations. The torque transmitted to the latch pin is then believed to have caused the latch pin
cross bolt to fail in shear.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: March 09, 2010
757-52A0091Revision 1: December 19, 2014
7 of 62

### Page 8

If the latch pin cross bolt fails, the latch pin could migrate either towards the cam latch or away from the cam
latch. Latch pin migration towards the cam latch can cause significant interference with the mating cam latch
leading to cam latch damage. In this case, the latch pin migrated into the cam latch and caused damage to the
cam latch. The crack initiated at the damage site caused by the latch pin and then led to the cam latch breaking.
Latch pin migration away from the cam latch could cause disengagement from the cam latch, resulting in no
load transfer between the cam latch and the mating latch pin and may not be noticed before critical conditions
are exceeded in adjacent cam latches or latch pins.
Accomplishment of the work given in this service bulletin will make sure the cam latches, latch pins and latch
pin cross bolt are inspected and repaired or replaced as required. The MCD rig will be verified to the Service
Bulletin requirements and if necessary, the MCD will be re-rigged to the updated AMM requirements.
Since the original report, there have been two additional reports of sheared latch pin cross bolts.
Boeing Service Related Problem (SRP) 757-SRP-52-0088 is related to this service bulletin.
This table is provided to operators for planning purposes only. Refer to the applicable sections for more
information.
ReferenceAffectedPlanning Data
Paragraph 1.A.2., Spares AffectedNoSpares Affected
Paragraph 1.E., Compliance and Paragraph
1.F., Approval
YesAD Related
Paragraph 1.H., Weight and Balance ChangesNoWeight and Balance Change
Paragraph 1.I., Electrical Load DataNoElectrical Load Changed
Paragraph 1.K., Publications AffectedYesPublications Affected
Paragraph 1.K., Publications AffectedNoAirplane Flight Operations Affected (Flight Crew
Operations Manual and/or FAA Approved Air-
plane Flight Manual)
Paragraph 2.C.1., Kits/PartsNoKits/Parts Required
Paragraph 2.C.2., Parts and Materials Supplied
by the Operator
NoOperator Supplied Parts/Material
Paragraph 2.F., Special Tooling Necessary to
do this Service Bulletin
NoSpecial Tooling Required
ACTION
Get access to the MCD. Do a general visual inspection of the cam latches, latch pins and latch pin cross bolt.
Torque the cross bolts in the latch pins. Measure the extension of the latch pins. Replace all alloy steel cross
bolts through the latch pins with Corrosion Resistant Steel (CRES) cross bolts. Check for lip deformation on all
cam latches. Do a High Frequency Eddy Current (HFEC) or magnetic particle inspection of cam latch 1 and
cam latch 2 for cracks. Replace any cracked or broken parts. Check the rig of the MCD to the requirements of
the Service Bulletin and if necessary, the MCD will be re-rigged to the latest AMM requirements. Do repetitive
general visual and detailed inspections of the cam latches and latch pins after the rig is verified or adjusted. Do
repetitive HFEC or magnetic particle inspections of cam latch 1 and cam latch 2 for cracks after the rig is verified
or adjusted.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: March 09, 2010
757-52A0091Revision 1: December 19, 2014
8 of 62
BOEING SERVICE BULLETIN 757-52A0091
ALERTALERT

### Page 9

EFFECTIVITY
757-200CB, 757-200PF and 757-200 Special Freighter delivered under a Boeing Supplemental Type Certificate
(STC) Airplanes. Refer to Paragraph 1.A.1., Airplanes for the list of affected airplanes.
COMPLIANCE
Federal Aviation Administration (FAA) Notice of Proposed Rule Making NPRM 2011-NM-163-AD, is related to
this service bulletin.
Refer to Paragraph 1.E., Compliance.
INDUSTRY SUPPORT INFORMATION
Boeing warranty remedies are not available for the inspections and modifications given in this service bulletin.
MANPOWER
Refer to Paragraph 1.G., Manpower.
MATERIAL INFORMATION
Operator Supplied Parts/Materials.
Refer to Paragraph 2.A., Material - Price and Availability
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: March 09, 2010
757-52A0091Revision 1: December 19, 2014
9 of 62
BOEING SERVICE BULLETIN 757-52A0091
ALERTALERT

### Page 10 (OCR)

BOEING SERVICE BULLETIN 757-52A0091
ALERT  ALERT
MAIN CARGO DOORWAY
LOWER SILL
LATCH PIN
- DO A GENERAL VISUAL INSPECTION OF THE CAM LATCHES,
LATCH PINS, AND LATCH PIN CROSS BOLTS.
TORQUE THE LATCH PIN CROSS BOLTS IN THE LATCH PINS.
MEASURE THE EXTENSION OF THE LATCH PINS.
• REPLACE ALL THE ALLOY STEEL CROSS BOLTS THROUGH THE
LATCH PINS WITH CRES LATCH PIN CROSS BOLTS
CHECK FOR LIP DEFORMATION ON ALL CAM LATCHES.
DO A HFEC OR MAGNETIC PARTICLE INSPECTION
OF CAM LATCH 1 AND CAM LATCH 2 FOR CRACKS.
• CHECK THE RIG OF THE MCD
REPLACE DAMAGED LATCH PINS AND CAM LATCHES.
- RIG THE MCD IF NECESSARY
• DO REPETITIVE POST-RIG CHECK INSPECTIONS.
CAM LATCH
1672966
Original Issue: March 09, 2010
Revision 1: December 19, 2014  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  757-52A0091
Work - See page 1 for details.  10 of 62

### Page 11

Commercial 
Airplanes
757
Service Bulletin
ALERT
Number: 757-52A0091
Original Issue: March 09, 2010
Revision 1: December 19, 2014
ATA System: 5232
SUBJECT: DOORS - Main Cargo Door - Cam Latch and Latch Pin Inspection and Modification
THIS BULLETIN IS SENT TO THE OPERATORS OF RECORD OF THE AIRPLANES SHOWN IN PARAGRAPH
1.A., EFFECTIVITY. IF AN AIRPLANE HAS BEEN LEASED OR SOLD, SEND THIS SERVICE BULLETIN TO
THE NEW OPERATOR. IF APPLICABLE SPARES HAVE BEEN SOLD, SEND THIS SERVICE BULLETIN TO
THE NEW OWNER.
1.    PLANNING INFORMATION
A. Effectivity
1. Airplanes
Refer to Service Bulletin Index Document D624N001 Part 3 for Airplane Variable Number, Line
Number, and Serial Number data.
This service bulletin is for the airplanes shown below.
DESCRIPTIONCONFIGURATIONGROUP
757-200PF, 757-200CB and 757-200 Special Freighter delivered
under a Boeing Supplemental Type Certificate (STC) Airplanes
-1
Airplane Models:
757-200, 757-200CB, 757-200PF
GroupVariable Number
1NA201 - NA204
1NA206 - NA213
1NA215 - NA236
1NC901 - NC951
1NC971
1NC973 - NC974
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: March 09, 2010
757-52A0091Revision 1: December 19, 2014
11 of 62

### Page 12

GroupVariable Number
1ND895
1NS601 - NS616
1NT001 - NT009
2. Spares Affected
None.
B. Concurrent Requirements
None.
C. Reason
Accomplishment of the inspections in this service bulletin will make sure the Main Cargo Door (MCD)
cam latches are inspected for damage and the latch pins are inspected for damage and migration. The
inspections are necessary in order to find and replace damaged cam latches, latch pins and latch pin
cross bolts. If not replaced, damaged cam latches, latch pins and latch pin cross bolts could lead to a
failure of the cam latches and may result in a possible rapid decompression and potential separation
of the cargo door from the airplane.
Boeing has received one report from one operator that the MCD forward most cam latch on the forward
center cam latch pair (cam latch number 3) broke during flight. The airplane that reported the broken
cam latch had 20,000 flight hours and 9,500 flight cycles when the cam latch broke. The crew heard
a loud noise coming from the MCD shortly after cruise. Upon landing, an inspection was performed
and a cam latch was found broken. The broken cam latch mating latch pin was also found to have
significant wear as evidenced by the loss of the plating on the surface that is normally in contact with
the cam. The latch pin was also deformed approximately 0.05 inch in the area of the wear surface.
The cause of the broken cam latch has been determined to be from a poorly rigged MCD. Although
rigged per the original Aircraft Maintenance Manual (AMM) procedures, significant variation was allowed
in the rigging dimensions. This variation can cause some of the latch pin/cam latch locations to have
a significant preload placed on them during engagement and rotation of the cam latches during latching
and unlatching operations. This preload is believed to have imparted a torque on the latch pin from the
cam latch rotation during latching and unlatching operations. The torque transmitted to the latch pin is
then believed to have caused the latch pin cross bolt to fail in shear.
If the latch pin cross bolt fails, the latch pin could migrate either towards the cam latch or away from
the cam latch. Latch pin migration towards the cam latch can cause significant interference with the
mating cam latch leading to cam latch damage. In this case, the latch pin migrated into the cam latch
and caused damage to the cam latch. The crack initiated at the damage site caused by the latch pin
and then led to the cam latch breaking. Latch pin migration away from the cam latch could cause
disengagement from the cam latch, resulting in no load transfer between the cam latch and the mating
latch pin and may not be noticed before critical conditions are exceeded in adjacent cam latches or
latch pins.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: March 09, 2010
757-52A0091Revision 1: December 19, 2014
12 of 62
BOEING SERVICE BULLETIN 757-52A0091
ALERTALERT

### Page 13

Accomplishment of the work given in this service bulletin will make sure the cam latches, latch pins
and latch pin cross bolts are inspected and repaired or replaced as required. The MCD rig will be
verified to the Service Bulletin requirements and if necessary, the MCD will be re-rigged to the latest
AMM requirements.
Since the original report, there have been two additional reports of a sheared latch pin cross bolts.
Boeing Service Related Problem (SRP) 757-SRP-52-0088 is related to this service bulletin.
Revision 1 is sent to clarify the requirements of the compliance tables.
D. Description
Get access to the MCD. Do a general visual inspection of the cam latches, latch pins and latch pin
cross bolts. Torque the cross bolts in the latch pins. Measure the extension of the latch pins. Replace
all alloy steel cross bolts through the latch pins with CRES cross bolts. Check for lip deformation on
all cam latches. Do a HFEC or magnetic particle inspection of cam latch 1 and cam latch 2 for cracks.
Replace any cracked or broken parts. The MCD rig will be verified to the Service Bulletin requirements
and if necessary, the MCD will be re-rigged to the updated AMM requirements. Do repetitive general
visual and detailed inspections of the cam latches and latch pins after the rig is verified or adjusted.
Do repetitive HFEC or magnetic particle inspections of cam latch 1 and cam latch 2 for cracks after
the rig is verified or adjusted.
Effects of this Issue on airplanes on which Original Issue was previously done:
None
The work in this service bulletin is done in the maintenance zone(s) given below.
Affected Maintenance Zones
ZoneModel
838757-200, 757-200CB, 757-
200PF
E. Compliance
Federal Aviation Administration (FAA) Notice of Proposed Rule Making NPRM 2011-NM-163-AD, is
related to this service bulletin.
If all Table 1 requirements, including rigging of the main cargo door, have been accomplished in
accordance with the original issue of this service bulletin, continue repetitive inspections in accordance
with Table 2.
If Table 1 requirements have not been accomplished in accordance with the original issue of this service
bulletin, then all Table 1 requirements, including rigging of the main cargo door, must be accomplished
before starting Table 2 requirements.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: March 09, 2010
757-52A0091Revision 1: December 19, 2014
13 of 62
BOEING SERVICE BULLETIN 757-52A0091
ALERTALERT

### Page 14

Table 1: Initial and Repetitive Inspections of the Cam Latches, Latch Pins and Latch Pin Cross Bolts for
the Main Cargo Door (Pre-Rig Check)
Repeat Interval (Not to
Exceed)
Compliance Time (Whichever
Occurs First)
ActionCondition
-Within 150 days
after the origi-
nal issue date
of this service
bulletin.
Within 330 flight
cycles after the
original issue
date of this ser-
vice bulletin.
Do the following for all
MCD cam latches and
latch pins:
Do a general visual in-
spection for any broken
cam latches, latch pins
and latch pin cross bolts,
and for any missing cam
latches, latch pins and
latch pin cross bolts in
accordance with Para-
graph 3.B., Work Instruc-
tions Step 1.b.
All airplanes
AND
Torque the cross bolts in
the latch pins in accor-
dance with Paragraph
3.B., Work Instructions
Step 1.c.
AND
Measure the extension
of the latch pins in accor-
dance with Paragraph
3.B., Work Instructions
Step 1.d.
AND
Do a general visual in-
spection of all cam
latches for lip deforma-
tion in accordance with
Paragraph 3.B., Work
Instructions Step 1.e.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: March 09, 2010
757-52A0091Revision 1: December 19, 2014
14 of 62
BOEING SERVICE BULLETIN 757-52A0091
ALERTALERT

### Page 15

Table 1: Initial and Repetitive Inspections of the Cam Latches, Latch Pins and Latch Pin Cross Bolts for
the Main Cargo Door (Pre-Rig Check)
Repeat Interval (Not to
Exceed)
Compliance Time (Whichever
Occurs First)
ActionCondition
-Before further flightReplace all broken and
missing cam latches,
latch pins and latch pin
cross bolts in accor-
dance with Paragraph
3.B., Work Instructions
Step 2.a.
Condition 1: One or
more of the following is
found:
1. Broken or
missing cam
latch(es).
2. Broken or
missing latch
pin(s).
3. Broken or
missing latch
pin cross
bolt(s).
AND
Do a detailed inspection
of mating part(s) and im-
mediately adjacent cam
latch(es) and latch pin(s)
for any cracks, or any
gouges in critical areas
in accordance with
Paragraph 3.B., Work
Instructions Step 2.b.
AND
Unless replaced with
new or reworked parts,
do a HFEC or magnetic
particle inspection of
cam latch 1 and cam
latch 2 for any cracks in
accordance with Para-
graph 3.B., Work Instruc-
tions Step 2.c.
(b)
AND
Check the rig of the
MCD in accordance with
Paragraph 3.B., Work
Instructions Step 2.d.
AND
Replace all alloy steel
cross bolts through the
latch pins with CRES
cross bolts in accor-
dance with Paragraph
3.B., Work Instructions
Step 2.d.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: March 09, 2010
757-52A0091Revision 1: December 19, 2014
15 of 62
BOEING SERVICE BULLETIN 757-52A0091
ALERTALERT

### Page 16

Table 1: Initial and Repetitive Inspections of the Cam Latches, Latch Pins and Latch Pin Cross Bolts for
the Main Cargo Door (Pre-Rig Check)
Repeat Interval (Not to
Exceed)
Compliance Time (Whichever
Occurs First)
ActionCondition
-Within 150 days
after the latch
pin extension
was measured.
Within 330 flight
cycles after the
latch pin exten-
sion was mea-
sured.
Replace the discrepant
latch pin in accordance
with Paragraph 3.B.,
Work Instructions Step
3.a.
Condition 2: The latch
pin extension is less
than 0.89 inches or
greater than 0.91 inches.
AND
Do a detailed inspection
of the mating cam latch
for any cracks, or
gouges in critical areas
in accordance with
Paragraph 3.B., Work
Instructions Step 3.b.
330 flight cycles or 150
days, whichever occurs
first. (a)
Within 150 days
after the initial
inspection.
Within 330 flight
cycles after the
initial inspec-
tion.
Do the following for all
MCD cam latches and
latch pins:
Do a general visual in-
spection for any broken
cam latches, latch pins
and latch pin cross bolts,
and for any missing cam
latches, latch pins and
latch pin cross bolts in
accordance with Para-
graph 3.B., Work Instruc-
tions Step 3.c.
AND
-Within 24
months after
the original is-
sue date of this
service bulletin.
Within 3,000
flight cycles af-
ter the original
issue date of
this service bul-
letin.
Do a detailed inspection
of all cam latches and
mating latch pins for any
cracks, or gouges in crit-
ical areas in accordance
with Paragraph 3.B.,
Work Instructions Step
3.d.
-Within 24
months after
the original is-
sue date of this
service bulletin.
Within 3,000
flight cycles af-
ter the original
issue date of
this service bul-
letin.
Unless replaced with
new or reworked parts,
do a HFEC or magnetic
particle inspection of
cam latch 1 and cam
latch 2 for any cracks in
accordance with Para-
graph 3.B., Work Instruc-
tions Step 3.e.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: March 09, 2010
757-52A0091Revision 1: December 19, 2014
16 of 62
BOEING SERVICE BULLETIN 757-52A0091
ALERTALERT

### Page 17

Table 1: Initial and Repetitive Inspections of the Cam Latches, Latch Pins and Latch Pin Cross Bolts for
the Main Cargo Door (Pre-Rig Check)
Repeat Interval (Not to
Exceed)
Compliance Time (Whichever
Occurs First)
ActionCondition
(b)
AND
Check the rig of the
MCD in accordance with
Paragraph 3.B., Work
Instructions Step 3.f.
AND
Replace all alloy steel
cross bolts through the
latch pins with CRES
cross bolts in accor-
dance with Paragraph
3.B., Work Instructions
Step 3.f.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: March 09, 2010
757-52A0091Revision 1: December 19, 2014
17 of 62
BOEING SERVICE BULLETIN 757-52A0091
ALERTALERT

### Page 18

Table 1: Initial and Repetitive Inspections of the Cam Latches, Latch Pins and Latch Pin Cross Bolts for
the Main Cargo Door (Pre-Rig Check)
Repeat Interval (Not to
Exceed)
Compliance Time (Whichever
Occurs First)
ActionCondition
330 flight cycles or 150
days, whichever occurs
first.
Within 150 days
after the initial
inspection.
Within 330 flight
cycles after the
initial inspec-
tion.
Do a detailed inspection
of the discrepant cam
latch and mating latch
pin for any cracks, or
gouges in critical areas
in accordance with
Paragraph 3.B., Work
Instructions Step 4.a.
Condition 3: If a cam
latch is found with lip
deformation.
(a)
AND
330 flight cycles or 150
days, whichever occurs
first.
Within 150 days
after the initial
inspection.
Within 330 flight
cycles after the
initial inspec-
tion.
Do the following for all
MCD cam latches and
latch pins:
Do a general visual in-
spection for any broken
cam latches, latch pins
and latch pin cross bolts,
and for any missing cam
latches, latch pins and
latch pin cross bolts in
accordance with Para-
graph 3.B., Work Instruc-
tions Step 4.b.
(a)
AND
-Within 24
months after
the original is-
sue date of the
service bulletin.
Within 3,000
flight cycles af-
ter the original
issue date of
the service bul-
letin.
Do a detailed inspection
of all cam latches and
mating latch pins for any
cracks, or gouges in crit-
ical areas in accordance
with Paragraph 3.B.,
Work Instructions Step
4.c.
AND
-Within 24
months after
the original is-
sue date of the
service bulletin.
Within 3,000
flight cycles af-
ter the original
issue date of
the service bul-
letin.
Unless replaced with
new or reworked parts,
do a HFEC or magnetic
particle inspection of
cam latch 1 and cam
latch 2 for any cracks in
accordance with Para-
graph 3.B., Work Instruc-
tions Step 4.d.
(b)
AND
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: March 09, 2010
757-52A0091Revision 1: December 19, 2014
18 of 62
BOEING SERVICE BULLETIN 757-52A0091
ALERTALERT

### Page 19

Table 1: Initial and Repetitive Inspections of the Cam Latches, Latch Pins and Latch Pin Cross Bolts for
the Main Cargo Door (Pre-Rig Check)
Repeat Interval (Not to
Exceed)
Compliance Time (Whichever
Occurs First)
ActionCondition
Check the rig of the
MCD in accordance with
Paragraph 3.B., Work
Instructions Step 4.e.
AND
Replace all alloy steel
cross bolts through the
latch pins with CRES
cross bolts in accor-
dance with Paragraph
3.B., Work Instructions
Step 4.e.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: March 09, 2010
757-52A0091Revision 1: December 19, 2014
19 of 62
BOEING SERVICE BULLETIN 757-52A0091
ALERTALERT

### Page 20

Table 1: Initial and Repetitive Inspections of the Cam Latches, Latch Pins and Latch Pin Cross Bolts for
the Main Cargo Door (Pre-Rig Check)
Repeat Interval (Not to
Exceed)
Compliance Time (Whichever
Occurs First)
ActionCondition
330 flight cycles or 150
days, whichever occurs
first.
Within 150 days
after the initial
inspection.
Within 330 flight
cycles after the
initial inspec-
tion.
Do a general visual in-
spection for any broken
and missing cam latch-
es, latch pins and latch
pin cross bolts in accor-
dance with Paragraph
3.B., Work Instructions
Step 5.a.
Condition 4: No discrep-
ancies found (c)
(a)
3,000 flight cycles or 24
months, whichever oc-
curs first.
Within 24
months after
the initial inspec-
tion.
Within 3,000
flight cycles af-
ter the initial in-
spection.
Do a detailed inspection
of the cam latches and
latch pins for any cracks,
or any gouges in critical
areas in accordance with
Paragraph 3.B., Work
Instructions Step 5.b.
(a)
AND
Unless replaced with
new or reworked parts,
do a HFEC or magnetic
particle inspection of
cam latch 1 and cam
latch 2 for any cracks in
accordance with Para-
graph 3.B., Work Instruc-
tions Step 5.c.
(b)
-Within 48
months after
the original is-
sue date of this
service bulletin.
Within 6,000
flight cycles af-
ter the original
issue date of
this service bul-
letin.
Check the rig of the
MCD in accordance with
Paragraph 3.B., Work
Instructions Step 5.d.
AND
Replace all alloy steel
cross bolts through the
latch pins with CRES
cross bolts in accor-
dance with Paragraph
3.B., Work Instructions
Step 5.d.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: March 09, 2010
757-52A0091Revision 1: December 19, 2014
20 of 62
BOEING SERVICE BULLETIN 757-52A0091
ALERTALERT

### Page 21

Table 1: Initial and Repetitive Inspections of the Cam Latches, Latch Pins and Latch Pin Cross Bolts for
the Main Cargo Door (Pre-Rig Check)
Repeat Interval (Not to
Exceed)
Compliance Time (Whichever
Occurs First)
ActionCondition
-Before further flight.Replace cracked or
gouged cam latch(es)
and latch pin(s) in accor-
dance with Paragraph
3.B., Work Instructions
Step 6.a.
Condition 5: If the de-
tailed, HFEC or magnet-
ic particle inspections in
Conditions 1 thru 4 re-
veal any of the following:
1. Cracked or
gouged cam
latch(es) in crit-
ical areas.
2. Cracked or
gouged latch
pin(s) in critical
areas.
AND
Do a detailed inspection
of mating part(s) and im-
mediately adjacent cam
latch(es) and latch pin(s)
for any cracks, or any
gouges in critical areas
in accordance with
Paragraph 3.B., Work
Instructions Step 6.b.
AND
Unless replaced with
new or reworked parts,
do a HFEC or magnetic
particle inspection of
cam latch 1 and cam
latch 2 for any cracks in
accordance with Para-
graph 3.B., Work Instruc-
tions Step 6.c. (b)
AND
Check the rig of the
MCD in accordance with
Paragraph 3.B., Work
Instructions Step 6.d.
AND
Replace all alloy steel
cross bolts through the
latch pins with CRES
cross bolts in accor-
dance with Paragraph
3.B., Work Instructions
Step 5.e.
(a) All Table 1 repeat inspections are terminated when the rig of the MCD has been checked in accordance
Paragraph 3.B., Work Instructions. Refer to Table 2 for post-rig check inspection requirements.
(b) A reworked cam latch is defined as a cam latch that has been reworked within limits of CMM 52-32-03
and/or a Boeing ODA approved repair via FAA Form 8100-9 and has been HFEC or magnetic particle in-
spected, and has no crack(s) or gouge(s) in critical area(s).
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: March 09, 2010
757-52A0091Revision 1: December 19, 2014
21 of 62
BOEING SERVICE BULLETIN 757-52A0091
ALERTALERT

### Page 22

Table 1: Initial and Repetitive Inspections of the Cam Latches, Latch Pins and Latch Pin Cross Bolts for
the Main Cargo Door (Pre-Rig Check)
Repeat Interval (Not to
Exceed)
Compliance Time (Whichever
Occurs First)
ActionCondition
(c) Discrepancy is defined as: Any broken, cracked, missing or gouged cam latches or latch pins, broken or
missing latch pin cross bolts, latch pin extension less than 0.89 inches or greater than 0.91 inches, or cam
latch lip deformation.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: March 09, 2010
757-52A0091Revision 1: December 19, 2014
22 of 62
BOEING SERVICE BULLETIN 757-52A0091
ALERTALERT

### Page 23

Table 2: Repetitive Inspection Requirements for Airplanes that have accomplished All Table 1 Require-
ments, Including Rigging of the Main Cargo Door in accordance with the Original Issue or Revision 1 of
this service bulletin.
Repeat Inter-
val (Not to
Exceed)
Compliance Time (Whichever Occurs
Later)
ActionCondition
375 flight cy-
cles.
Within 375 flight cycles after the rig of the
MCD was checked.
Do a general visual in-
spection for any broken
or missing cam latches,
latch pins and latch pin
cross bolts in accordance
with Paragraph 3.B.,
Work Instructions Step
7.a.1.
Condition 6: Airplanes
that have accomplished
all Table 1 requirements,
including rigging of the
main cargo door in accor-
dance with the original
issue or revision 1 of this
service bulletin and no
rigging adjustment of any
latch pin or any latch pin
fitting was required.
3,000 flight cy-
cles.
If latch pin flight cycles are known:
Before 40,000 total latch pin flight cycles.
Do a detailed inspection
of the latch pins for any
cracks, or any gouges in
critical areas in accor-
dance with Paragraph
3.B., Work Instructions
Step 7.a.2.
3,000 flight cy-
cles.
If latch pin flight cycles are unknown:
Within 3,000 flight cycles after the rig of
the MCD was checked.
AND
During previous pre-rig
check inspection no dis-
crepancy was found. (b)
3,000 flight cy-
cles.
If cam latch flight cycles are known and
cam latch is not a reworked part:
Do a detailed inspection
of the cam latches for
any cracks, or any
gouges in critical areas
in accordance with Para-
graph 3.B., Work Instruc-
tions Step 7.a.2.
(a)
Before 40,000 total cam latch flight cycles.
3,000 flight cy-
cles.
If cam latch flight cycles are unknown or
if cam latch is a reworked part:
(a)
Within 3,000 flight cycles after the rig of
the MCD was checked.
6,000 flight cy-
cles.
If cam latch flight cycles are known and
cam latch is not a reworked part:
Do a HFEC or magnetic
particle inspection of cam
latch 1 and cam latch 2
for any cracks in accor-
dance with Paragraph
3.B., Work Instructions
Step 7.a.3.
(a)
Before 40,000 total cam latch flight cycles.
6,000 flight cy-
cles.
If cam latch flight cycles are unknown or
if cam latch is a reworked part:
(a)
Within 6,000 flight cycles after the rig of
the MCD was checked.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: March 09, 2010
757-52A0091Revision 1: December 19, 2014
23 of 62
BOEING SERVICE BULLETIN 757-52A0091
ALERTALERT

### Page 24

Table 2: Repetitive Inspection Requirements for Airplanes that have accomplished All Table 1 Require-
ments, Including Rigging of the Main Cargo Door in accordance with the Original Issue or Revision 1 of
this service bulletin.
Repeat Inter-
val (Not to
Exceed)
Compliance Time (Whichever Occurs
Later)
ActionCondition
375 flight cy-
cles.
Within 375 flight cycles after the rig of the
MCD was checked.
Do a general visual in-
spection for any broken
or missing cam latch(es),
latch pin(s) and latch pin
cross bolt(s) in accor-
dance with Paragraph
3.B., Work Instructions
Step 8.a.1
Condition 7: Airplanes
that have accomplished
all Table 1 requirements,
including rigging of the
main cargo door in accor-
dance with the original
issue or revision 1 of this
service bulletin and rig-
ging adjustment of any
latch pin or any latch pin
fitting was required.
3,000 flight cy-
cles.
Within 3,000 flight cycles after the rig of
the MCD was checked.
Do a detailed inspection
of the cam latches and
latch pins for any cracks,
or any gouges in critical
areas in accordance with
Paragraph 3.B., Work In-
structions Step 8.a.2
OR
During previous pre-rig
check inspection, any
discrepancy was found.
(b)
6,000 flight cy-
cles.
Within 6,000 flight cycles after the rig of
the MCD was checked.
Do a HFEC or magnetic
particle inspection of cam
latch 1 and cam latch 2
for any cracks in accor-
dance with Paragraph
3.B., Work Instructions
Step 8.a.3
-Before further flight.Contact The Boeing
Company for repair in-
structions and do the re-
pair.
Any discrepancy found
during Condition 6 or
Condition 7 inspections.
(a) A reworked cam latch is defined as a cam latch that has been reworked within limits of CMM 52-32-03
and/or a Boeing ODA approved repair via FAA Form 8100-9 and has been HFEC or magnetic particle in-
spected, and has no crack(s) or gouge(s) in critical area(s).
(b) Discrepancy is defined as: Any broken, cracked, missing or gouged cam latches or latch pins, broken or
missing latch pin cross bolts, latch pin extension less than 0.89 inches or greater than 0.91 inches, or cam
latch lip deformation.
F. Approval
This service bulletin was examined by the Federal Aviation Administration (FAA). The changes specified
in this service bulletin comply with the applicable regulations and are FAA approved, as well as European
Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved
airplanes listed in the service bulletin effectivity. This service bulletin and its approval were based on
the airplane in its original Boeing delivery configuration or as modified by other approved Boeing
changes.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: March 09, 2010
757-52A0091Revision 1: December 19, 2014
24 of 62
BOEING SERVICE BULLETIN 757-52A0091
ALERTALERT

### Page 25

If an airplane has a non-Boeing modification or repair that affects a component or system also affected
by this service bulletin, the operator is responsible for obtaining appropriate regulatory agency approval
before incorporating this service bulletin.
G. Manpower
The table below shows an estimate of the task hours necessary to do the inspections and modifications
for each airplane. This estimate is for direct labor only, done by an experienced crew. Adjust the estimate
with operator task hour data if necessary. The estimate does not include lost time. These are some
examples of lost time:
 Time to adjust to the workplace
 Time to schedule the work
 Time to inspect the work
 Time to cure the materials
 Time to make the parts
 Time to find the tools.
Elapsed HoursTask HoursNumber of Per-
sons
Task
0.250.251Open Access
1.601.601FIGURE 1
0.500.501FIGURE 2
0.500.501FIGURE 3
1.00(h)1.00(h)1FIGURE 4
1.001.001FIGURE 5
0.50(a) (f) (i)0.50(a) (f) (i)1(i)FIGURE 6
0.10(b) (g)0.10(b) (g)1FIGURE 7
0.60(c)0.60(c)1FIGURE 8
0.10(d)0.10(d)1FIGURE 9
20.048.02-3FIGURE 10 - FIG-
URE 11
0.250.251Close Access
(e)(e)TOTAL FOR EACH AIRPLANE
(a) Estimate is per cam latch requiring replacement.
(b) Estimate is per latch pin requiring replacement.
(c) Estimate is per cam latch requiring inspection.
(d) Estimate is per cam latch.
(e) Total time required may vary depending upon conditions found during inspec-
tions.
(f) Does not include time to match drill cam shaft.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: March 09, 2010
757-52A0091Revision 1: December 19, 2014
25 of 62
BOEING SERVICE BULLETIN 757-52A0091
ALERTALERT

### Page 26

Elapsed HoursTask HoursNumber of Per-
sons
Task
(g) Does not include time to match drill latch pin
(h) Does not include NDI inspection time
(i) Cam latch 4 will require 2 hours and a second person to remove.
H. Weight and Balance Changes
Change in Moment
(Pound-Inches)
Change in Weight
(Pounds)Airplane
NegligibleNegligible757-200CB
NegligibleNegligible757-200PF
NegligibleNegligible757-200 Special
Freighter
I. Electrical Load Data
Not changed.
J. References
1. Existing Data:
a. Boeing Service Related Problem (SRP) 757-SRP-52-0088
b. Component Maintenance Manual (CMM) 52-32-03, Repair 7-2.
c. Federal Aviation Administration (FAA) Notice of Proposed Rule Making (NPRM)
2011-NM-163-AD
d. Standard Overhaul Practices Manual (SOPM) 20-20-01
e. 757 Aircraft Maintenance Manual (AMM) 52-32-00
f. 757 Non-Destructive Testing (NDT) Manual Part 6, 51-00-12 or 51-00-21
2. Data Supplied with this Service Bulletin:
None.
3. Installation Drawings Used in the Preparation of this Service Bulletin:
TitleDrawing Number
DOOR INSTALLATION - MAIN CARGO65-25326
LATCH MECHANISM INSTALLATION - MAIN CARGO DOOR65-25339
SILL INSTL - LOWER, MAIN CARGO DOOR143N8750
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: March 09, 2010
757-52A0091Revision 1: December 19, 2014
26 of 62
BOEING SERVICE BULLETIN 757-52A0091
ALERTALERT

### Page 27

TitleDrawing Number
LATCH PIN FITTING - ASSY65-67872
CAM - LATCH MECHANISM CARGO DOOR69-23438
These drawings were used to prepare this service bulletin. These drawings are not necessary to
make the specified changes, and are not supplied with this service bulletin. These drawings may
not be applicable to all airplane configurations or operators.
K. Publications Affected
1. Publications:
Chapter-SectionPublication
52-32, 52-33757 Illustrated Parts Catalog
52-32757 Component Maintenance Manual
52-32757 Aircraft Maintenance Manual
2. Damage Tolerance Based Structural Inspections:
Boeing has evaluated the repairs and/or changes in this service bulletin for effects on Fatigue
Critical Structure (FCS) and for changes to Damage Tolerance Inspections (DTI) required in the
Maintenance Program. This service bulletin affects FCS. DTI requirements for the structure affected
are contained in Paragraph 1.E., Compliance of this service bulletin.
Repairs accomplished on cam latch(es) in accordance with CMM 52-32-03 are structurally
acceptable as Category A repairs as defined in 757-200 SRM 51-00-06, 757-200CB SRM 51-00-06
and 757-200PF SRM 51-00-06, therefore no supplemental inspections to the mandated damage
tolerance inspections contained in Paragraph 1.E., Compliance, Table 2, of this service bulletin,
are required.
L. Interchangeability and Intermixability of Parts
Accomplishment of this service bulletin does not affect interchangeability or intermixability of parts.
M. Software Accomplishment Summary
Not affected.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: March 09, 2010
757-52A0091Revision 1: December 19, 2014
27 of 62
BOEING SERVICE BULLETIN 757-52A0091
ALERTALERT

### Page 28

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: March 09, 2010
757-52A0091Revision 1: December 19, 2014
28 of 62
BOEING SERVICE BULLETIN 757-52A0091
ALERTALERT
BLANK PAGE

### Page 29

2.    MATERIAL INFORMATION
A. Material - Price and Availability
The operator can supply the parts and materials shown in Paragraph 2.C., Parts Necessary for Each
Airplane. As an alternative, operators can purchase the parts from Boeing Spares. This service bulletin
does not show the Boeing price and supply data.
B. Industry Support Information
Boeing warranty remedies are not available for the inspections and modifications given in this service
bulletin.
C. Parts Necessary for Each Airplane
1. Kits/Parts
None.
2. Parts and Materials Supplied by the Operator
NotesExisting Part NumberNameQTYPart Number /
Specification
(a) (b)NAS6603-24BOLT, HEX HEAD, 160 KSI MIN
TENSILE, LONG THREAD, A286,
NONLOCKING
8BACB30LM3-24
OR
BACB30LM3-22
OR
BACB30NF3-22
(c)69-23438-2Cam Latch 1169-23438-2
(c)143N8060-1Cam Latch 21143N8060-1
(c)143N8027-2Cam Latch 31143N8027-2
(c)69-23439-3Cam Latch 4169-23439-3
(c)69-23439-4Cam Latch 5169-23439-4
(c)143N8027-1Cam Latch 61143N8027-1
(c)143N8060-2Cam Latch 71143N8060-2
(c)69-23438-1Cam Latch 8169-23438-1
(c)6-83137-2Latch Pin86-83137-2
(a) Refer to 757 Structural Repair Manual Chapter 51 for alternate fasteners.
(b) BACB30LM3-24 and NAS6603-24 used if 143N8157-2 Clip Assembly is installed.
(c) Part numbers and quantities necessary are based on inspection findings.
NOTE: Rubber Quicksetting Putty (G50673) is needed if the door rigging procedure per 757
AMM 52-32-00 20Sep2008 Revision or later is used.
3. Parts Modified and Reidentified
None.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: March 09, 2010
757-52A0091Revision 1: December 19, 2014
29 of 62
BOEING SERVICE BULLETIN 757-52A0091
ALERTALERT

### Page 30

4. Parts Removed and Not Replaced
None.
D. Parts Necessary to Change Spares
None.
E. Special Tooling - Price and Availability
None.
F. Special Tooling Necessary to do this Service Bulletin
No special tools or equipment are necessary to do the change in this service bulletin. But, maintenance
and overhaul tools in the manuals given in Paragraph 1.J., References, can be necessary. Examine
operator tool supply to make sure all necessary tools are available.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: March 09, 2010
757-52A0091Revision 1: December 19, 2014
30 of 62
BOEING SERVICE BULLETIN 757-52A0091
ALERTALERT

### Page 31

3.    ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL INFORMATION
CAUTION: KEEP THE WORK AREA, WIRES AND ELECTRICAL BUNDLES CLEAN OF METAL
PARTICLES OR CONTAMINATION WHEN YOU USE TOOLS. UNWANTED MATERIAL,
METAL PARTICLES OR CONTAMINATION CAUGHT IN WIRE BUNDLES CAN CAUSE
DAMAGE TO THE BUNDLES. DAMAGED WIRE BUNDLES CAN CAUSE SPARKS OR
OTHER ELECTRICAL DAMAGE.
NOTE: 1. Manual titles are referred to by acronyms. Refer to Paragraph 1.J., References, for
definition of the acronyms.
2. Obey all of the warnings and cautions given in the specified manual sections.
3. Unless shown differently, these dimensions and tolerances are used:
– Linear dimensions are in inches
– Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus
or minus 0.03 inch
– Tolerance on rivet and bolt edge margin is plus or minus 0.05 inch
– Angular tolerance is plus or minus 2 degrees
– Hole dimensions for standard solid rivets and fasteners are in Structural Repair
Manual (SRM) Chapter 51
– Torque Values:
— Values for structural fasteners are given in 757 Structural Repair Manual,
Chapter 51.
— Values for airframe maintenance tasks are included in Chapter 20 of 757
Airplane Maintenance Manual (AMM).
— Non-standard torque values for maintenance tasks are included in the
applicable installation step.
4. Use the approved fastener, process and material substitutions in accordance with
SRM Chapter 51.
5. If the length of any fastener specified in this service bulletin does not meet installation
standards given in SRM Chapter 51, then a fastener of the same specification, or
an approved substitute, with a length which meets the installation standards given
in SRM Chapter 51 may be used. In addition, washers may be installed for fastener
grip length in accordance with SRM Chapter 51.
6. Clearance between fasteners and surrounding structures or mechanisms may be
minimal by design at some locations. Use caution when adjusting grip length of
fasteners and make sure no interference conditions exist after installation. Interference
between moving parts may be difficult to detect. Complete full cycle of mechanisms
to ensure no interference conditions exist.
7. A Detailed Inspection is defined as: An intensive examination of a specific item,
installation, or assembly to detect damage, failure, or irregularity. Available lighting
is normally supplemented with a direct source of good lighting at an intensity deemed
appropriate. Inspection aids such as mirrors, magnifying lenses, etc. may be
necessary. Surface cleaning and elaborate procedures may be required.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: March 09, 2010
757-52A0091Revision 1: December 19, 2014
31 of 62
BOEING SERVICE BULLETIN 757-52A0091
ALERTALERT

### Page 32

8. A General Visual Inspection is defined as: A visual examination of an interior or
exterior area, installation or assembly to detect obvious damage, failure or irregularity.
This level of inspection is made from within touching distance unless otherwise
specified. A mirror may be necessary to enhance visual access to all exposed surfaces
in the inspection area. This level of inspection is made under normally available
lighting conditions such as daylight, hangar lighting, flashlight or drop-light and may
require removal or opening of access panels or doors. Stands, ladders or platforms
may be required to gain proximity to the area being checked.
9. These work instructions refer to procedures included in other Boeing documents.
When the words "refer to" are used and the operator has an accepted alternative
procedure, the accepted alternative procedure can be used. When the words "in
accordance with" are included in the instruction, the procedure in the Boeing document
must be used.
10. The instructions in Paragraph 3.B., Work Instructions and the figures can include
operation of tools or test equipment. Boeing Engineering Tool Drawings, the Illustrated
Tool and Equipment Manual, and the Special Tool and Ground Handling Drawing
Index contain data on versions of the tools or test equipment that you can use. It is
permitted to use replaced tools. It is not permitted to use superseded tools.
11. If it is necessary to remove more parts for access, you can remove those parts. If
you can get access without removing identified parts, it is not necessary to remove
all of the identified parts. Jacking and shoring limitations must be observed.
12. Where the work instructions include installation of a kept part, a new or reworked
part with the same part number can be installed as an alternative to the kept part.
13. Damage found on cam latch(es) within the reworkable limits of CMM 52-32-03 can
be reworked in accordance with CMM 52-32-03.
14. A reworked cam latch is defined as a cam latch that has been reworked within the
limits of CMM 52-32-03 and/or a Boeing ODA approved repair via FAA Form 8100-9
and has been HFEC or magnetic particle inspected, and has no crack(s) or gouge(s)
in critical area(s).
15. Discrepancy is defined as: Any broken, cracked, missing or gouged cam latches or
latch pins, broken or missing latch pin cross bolts, latch pin extension less than 0.89
inches or greater than 0.91 inches, or cam latch lip deformation.
B. WORK INSTRUCTIONS
1. Initial (Pre-Rig Check) Inspections
a. Get access to the Main Cargo Door (MCD).
b. Do a general visual inspection for any broken cam latches, latch pins and latch pin cross bolts
and for any missing cam latches, latch pins and latch pin cross bolts in accordance with
FIGURE 9 .
c. Torque the cross bolts in the latch pins in accordance with FIGURE 2.
d. Measure the extension of the latch pins in accordance with FIGURE 3.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: March 09, 2010
757-52A0091Revision 1: December 19, 2014
32 of 62
BOEING SERVICE BULLETIN 757-52A0091
ALERTALERT

### Page 33

e. Do a general visual inspection of all cam latches for lip deformation in accordance with FIGURE
1.
2. Condition 1:
One or more of the following is found:
– Broken or missing cam latch(es)
– Broken or missing latch pin(s)
– Broken or missing latch pin cross bolt(s)
a. Replace broken or missing cam latch(es) in accordance with FIGURE 6, replace broken and
missing latch pin(s) in accordance with FIGURE 7 and replace broken and missing latch pin
cross bolt(s) in accordance with FIGURE 5.
b. Do a detailed inspection of mating part(s) and immediately adjacent cam latches and latch
pins for any cracks, or any gouges in critical areas in accordance with FIGURE 8. Do all
applicable corrective actions as described in Condition 5.
c. Unless replaced with new or reworked parts, do a HFEC or magnetic particle inspection of
cam latch 1 and cam latch 2 for of cracks in critical areas in accordance with FIGURE 4. Do
all applicable corrective actions as described in Condition 5.
d. Check the rig of the Main Cargo Door in accordance with FIGURE 10 and FIGURE 11, and
replace all alloy steel cross bolts through the latch pins with CRES cross bolts in accordance
with FIGURE 5. If MCD is out of rig and cannot be adjusted in accordance with FIGURE 10
and FIGURE 11, rig the MCD. Refer to 757 AMM 52-32-00 Rev 20Sep2008 or later as an
accepted procedure for MCD rigging.
3. Condition 2:
The latch pin extension is less than 0.89 inches or greater than 0.91 inches:
a. Replace the discrepant latch pin in accordance with FIGURE 7.
b. Do a detailed inspection of the mating cam latch for any cracks, or gouges in critical areas in
accordance with FIGURE 8. Do all applicable corrective actions as described in Condition 5.
c. Do a general visual inspection for any broken cam latches, latch pins and latch pin cross bolts
and for any missing cam latches, latch pins and latch pin cross bolts in accordance with
FIGURE 9 . Do all applicable corrective actions as described in Condition 1.
d. Do a detailed inspection of the latch pin(s) and mating cam latch(es) for any cracks, or any
gouges in critical areas in accordance with FIGURE 1. Do all applicable corrective actions as
described in Condition 5.
e. Unless replaced with new or reworked parts, do a HFEC or magnetic particle inspection of
cam latch 1 and cam latch 2 for any cracks in critical areas in accordance with FIGURE 4. Do
all applicable corrective actions as described in Condition 5.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: March 09, 2010
757-52A0091Revision 1: December 19, 2014
33 of 62
BOEING SERVICE BULLETIN 757-52A0091
ALERTALERT

### Page 34

f. Check the rig of the Main Cargo Door in accordance with FIGURE 10 and FIGURE 11, and
replace all alloy steel cross bolts through the latch pins with CRES cross bolts in accordance
with FIGURE 5. If MCD is out of rig and cannot be adjusted in accordance with FIGURE 10
and FIGURE 11, rig the MCD. Refer to 757 AMM 52-32-00 Rev 20Sep2008 or later as an
accepted procedure for MCD rigging.
NOTE: Rigging for the latch pin will require it to be installed properly with an extension of
0.90 +/- 0.01 inches. A latch pin with an original extension between 0.84 to 0.94
inches, with no cracks or gouges in critical areas and no other discrepancies may
be re-used by clocking the latch pin 90 degrees +/- 10 degrees from original position
and match drilling a new cross bolt hole that provides the correct latch pin extension.
Fill old cross bolt hole in pin with BMS 5-95 sealant and install pin with BMS 3-27
corrosion inhibiting compound.
4. Condition 3:
If a cam latch is found with lip deformation.
a. Do a detailed inspection of the discrepant cam latch and mating latch pin for any cracks, or
gouges in critical areas in accordance with FIGURE 1. Do all applicable corrective actions as
described in Condition 5.
b. Do a general visual inspection for any broken cam latches, latch pins and latch pin cross bolts
and for any missing cam latches, latch pins and latch pin cross bolts in accordance with
FIGURE 9. Do all applicable corrective actions as described in Condition 1.
c. Do a detailed inspection of the latch pin(s) and mating cam latch(es) for any cracks, or any
gouges in critical areas in accordance with FIGURE 1. Do all applicable corrective actions as
described in Condition 5.
d. Unless replaced with new or reworked parts, do a HFEC or magnetic particle inspection of
cam latch 1 and cam latch 2 for any cracks in critical areas in accordance with FIGURE 4. Do
all applicable corrective actions as described in Condition 5.
e. Check the rig of the Main Cargo Door in accordance with FIGURE 10 and FIGURE 11, and
replace all alloy steel cross bolts through the latch pins with CRES cross bolts in accordance
with FIGURE 5. If MCD is out of rig and cannot be adjusted in accordance with FIGURE 10
and FIGURE 11, rig the MCD. Refer to 757 AMM 52-32-00 Rev 20Sep2008 or later as an
accepted procedure for MCD rigging.
5. Condition 4:
No discrepancies found:
a. Do a general visual inspection for any broken and missing cam latches, latch pins and latch
pin cross bolts in accordance with FIGURE 9. Do all applicable corrective actions as described
in Condition 1.
b. Do a detailed inspection of the cam latches and latch pins for any cracks, or any gouges in
critical areas in accordance with FIGURE 1. Do all applicable corrective actions as described
in Condition 5.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: March 09, 2010
757-52A0091Revision 1: December 19, 2014
34 of 62
BOEING SERVICE BULLETIN 757-52A0091
ALERTALERT

### Page 35

c. Unless replaced with new or reworked parts, do a HFEC or magnetic particle inspection of
cam latch 1 and cam latch 2 for any cracks in critical areas in accordance with FIGURE 4. Do
all applicable corrective actions as described in Condition 5.
d. Check the rig of the Main Cargo Door in accordance with FIGURE 10 and FIGURE 11, and
replace all alloy steel cross bolts through the latch pins with CRES cross bolts in accordance
with FIGURE 5. If MCD is out of rig and cannot be adjusted in accordance with FIGURE 10
and FIGURE 11, rig the MCD. Refer to 757 AMM 52-32-00 Rev 20Sep2008 or later as an
accepted procedure for MCD rigging.
6. Condition 5:
If the detailed, HFEC or magnetic particle inspections in Conditions 1 thru 4 reveal any of the
following:
– Cracked or gouged cam latch(es) in critical areas.
– Cracked or gouged latch pin(s) in critical areas.
a. Replace cracked or gouged cam latch(es) in accordance with FIGURE 6, replace cracked or
gouged latch pin(s) in accordance with FIGURE 7.
b. Do a detailed inspection of mating part(s) and immediately adjacent cam latches and latch
pins for any cracks or any gouges in critical areas in accordance with FIGURE 8. Do all
applicable corrective actions as described in Condition 5.
c. Unless replaced with new or reworked parts, do a HFEC or magnetic particle inspection of
cam latch 1 and cam latch 2 for any cracks in critical areas in accordance with FIGURE 4. Do
all applicable corrective actions as described in Condition 5.
d. Check the rig of the MCD in accordance with FIGURE 10 and FIGURE 11 and replace all
alloy steel cross bolts with CRES cross bolts in accordance with FIGURE 5. If MCD is out of
rig and cannot be adjusted in accordance with FIGURE 10 and FIGURE 11, rig the MCD.
Refer to 757 AMM 52-32-00 Rev 20Sep2008 or later as an accepted procedure for MCD
rigging.
7. Post Rig Check Repetitive Inspections.
a. Condition 6:
Airplanes that have accomplished all Table 1 requirements identified in Paragraph 1.E.,
Compliance, including rigging of the main cargo door in accordance with the original issue or
revision 1 of this service bulletin and no rigging adjustment of any latch pin or any latch pin
fitting was required, and during previous pre-rig check inspections there were no discrepancies
found:
(1) Do a general visual inspection for any broken or missing cam latches, latch pins and latch
pin Cross Bolt in accordance with FIGURE 9.
(2) Do a detailed inspection of the cam latches and latch pins for any cracks or any gouges
in critical areas in accordance with FIGURE 1.
(3) Do a HFEC or magnetic particle inspection of cam latch 1 and cam latch 2 for any cracks
in critical areas in accordance with FIGURE 4.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: March 09, 2010
757-52A0091Revision 1: December 19, 2014
35 of 62
BOEING SERVICE BULLETIN 757-52A0091
ALERTALERT

### Page 36

(4) If any discrepancy is found during the Condition 6 inspections, contact The Boeing
Company for repair instructions and do the repair.
8. Post Rig Check Repetitive Inspections.
a. Condition 7:
Airplanes that have accomplished all Table 1 requirements identified in Paragraph 1.E.,
Compliance, including rigging of the main cargo door in accordance with the original issue or
revision 1 of this service bulletin and rigging adjustment of any latch pin or any latch pin fitting
was required, or during previous pre-rig check inspections there were any discrepancies found.
(1) Do a general visual inspection for any broken or missing cam latches, latch pins and latch
pin cross bolts in accordance with FIGURE 9.
(2) Do a detailed inspection of the cam latches and latch pins for any cracks or any gouges
in critical areas in accordance with FIGURE 1.
(3) Do a HFEC or magnetic particle inspection of cam latch 1 and cam latch 2 for any cracks
in critical areas in accordance with FIGURE 4.
(4) If any discrepancy is found during the Condition 7 inspections, contact The Boeing
Company for repair instructions and do the repair.
9. Put the airplane back to a serviceable condition.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: March 09, 2010
757-52A0091Revision 1: December 19, 2014
36 of 62
BOEING SERVICE BULLETIN 757-52A0091
ALERTALERT

### Page 37 (OCR)

BOEING SERVICE BULLETIN 757-52A0091
ALERT  ALERT
5) C
FIGURE 1: MAIN CARGO DOOR - CAM LATCHES AND LATCH PINS INSPECTION
(SHEET 1 OF 3)
Original Issue: March 09, 2010
Revision 1 December 19, 2014  Export Controlled ECCN: 9E991 - BOEING  757-52A0091
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  37 of 62

### Page 38 (OCR)

BOEING SERVICE BULLETIN 757-52A0091
ALERT  ALERT
LATCH PIN
(8 LOCATIONS)
(9)
CRITICAL AREA ENTIRE
CIRCUMFERENCE
0.3*
CRITICAL AREA
WEAR PLATE
CAM LATCH
LIP DEFORMATION
LOCATED OUTSIDE
NORMAL WEAR
AREAS
CRITICAL AREA
1673612
FIGURE 1: MAIN CARGO DOOR - CAM LATCHES AND LATCH PINS INSPECTION
(SHEET 2 OF 3)
Original Issue: March 09, 2010
Revision 1 December 19, 2014  Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright © Unpublished  757-52A0091
Work - See page 1 for details.  38 of 62

### Page 39

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
More DataQtyIdentificationNameTaskStep
Detailed inspection
of the cam latch.(a)
(b)
169-23438-2Cam Latch 1Inspect1
Detailed inspection
of the cam latch.(a)
(b)
1143N8060-1Cam Latch 2Inspect2
Detailed inspection
of the cam latch.(a)
(b)
1143N8027-2Cam Latch 3Inspect3
Detailed inspection
of the cam latch.(a)
(b)
169-23439-3Cam Latch 4Inspect4
Detailed inspection
of the cam latch.(a)
(b)
169-23439-4Cam Latch 5Inspect5
Detailed inspection
of the cam latch.(a)
(b)
1143N8027-1Cam Latch 6Inspect6
Detailed inspection
of the cam latch.(a)
(b)
1143N8060-2Cam Latch 7Inspect7
Detailed inspection
of the cam latch.(a)
(b)
169-23438-1Cam Latch 8Inspect8
Detailed inspection
of the latch pin.(a)
86-83137-2Latch PinInspect9
(a) Look for cracks or gouges in critical areas.
(b) Do a general visual inspection for lip deformation.
FIGURE 1: MAIN CARGO DOOR - CAM LATCHES AND LATCH PINS INSPECTION
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: March 09, 2010
757-52A0091Revision 1 December 19, 2014
39 of 62
BOEING SERVICE BULLETIN 757-52A0091
ALERTALERT

### Page 40 (OCR)

BOEING SERVICE BULLETIN 757-52A0091
ALERT  ALERT
MAIN CARGO DOORWAY
LOWER SILL
LATCH PIN FITTING
ASSEMBLY
(8 LOCATIONS)
LATCH PIN FITTING ASSEMBLY  (SHOWN WITH OPTIONAL CLIP  LATCH PIN  CROSS BOLT
ASSEMBLY INSTALLED)
1676653
FIGURE 2: MAIN CARGO DOOR - LATCH PIN CROSS BOLT TORQUE
(SHEET 1 OF 2)
Original Issue: March 09, 2010
Revision 1 December 19, 2014  Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright @ Unpublished  757-52A0091
Work - See page 1 for details.  40 of 62

### Page 41

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
More DataQtyIdentificationNameTaskStep
(a)8-Cross BoltTorque1
(a) Make sure the latch pin cross bolt is capable of reaching a 15 pound-inch, +/- 1 pound-inch, torque from
the head side of the bolt and also the nut side if no nutplate is used. The 15 pound-inch, +/- 1 pound-inch,
torque value is approximately one-half of the installation torque and is used to give an indication of a
broken cross bolt.
FIGURE 2: MAIN CARGO DOOR - LATCH PIN CROSS BOLT TORQUE
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: March 09, 2010
757-52A0091Revision 1 December 19, 2014
41 of 62
BOEING SERVICE BULLETIN 757-52A0091
ALERTALERT

### Page 42 (OCR)

BOEING SERVICE BULLETIN 757-52A0091
ALERT  ALERT
MAIN CARGO DOORWAY
LOWER SILL
LATCH PIN FITTING
ASSEMBLY
(8 LOCATIONS)
0.91
0.89
LATCH PIN FITTING ASSEMBLY
(SHOWN WITH OPTIONAL CLIP
ASSEMBLY INSTALLED)
WEAR PLATE
FIGURE 3: MAIN CARGO DOOR - LATCH PIN EXTENSION MEASUREMENT
(SHEET 1 OF 2)
Original Issue: March 09, 2010
Revision 1 December 19, 2014  Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright © Unpublished  757-52A0091
Work - See page 1 for details.  42 of 62

### Page 43

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
Make sure the latch
pin extends out 0.90
inch +/- 0.01 inch
from the wear plate.
86-83137-2Latch PinMeasure1
FIGURE 3: MAIN CARGO DOOR - LATCH PIN EXTENSION MEASUREMENT
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: March 09, 2010
757-52A0091Revision 1 December 19, 2014
43 of 62
BOEING SERVICE BULLETIN 757-52A0091
ALERTALERT

### Page 44 (OCR)

BOEING SERVICE BULLETIN 757-52A0091
ALERT  ALERT
4 A
A 2S
3) CRITICAL AREA
CAM LATCH
(3) CRITICAL AREA
1677155
FIGURE 4: MAIN CARGO DOOR - CAM LATCH 1 AND CAM LATCH 2 INSPECTION
(SHEET 1 OF 2)
Original Issue: March 09, 2010
Revision 1 December 19, 2014  Export Controlled ECCN: 9E991 - BOEING  757-52A0091
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  44 of 62

### Page 45

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
169-23438-2Cam Latch 1Remove / Keep1
1143N8060-1Cam Latch 2Remove / Keep2
Do a HFEC inspection of cam latch 1 for
cracks in accordance with 757 NDT Part 6,
51-00-12 or 51-00-21.(a) (b) (c)
169-23438-2Cam Latch 1Inspect3
Do a HFEC inspection of cam latch 2 for
cracks in accordance with 757 NDT Part 6,
51-00-12 or 51-00-21.(a) (b) (c)
1143N8060-1Cam Latch 2Inspect
169-23438-2Cam Latch 1Install (Kept)4
1143N8060-1Cam Latch 2Install (Kept)5
(a) Use a 0.080 inch diameter or smaller HFEC probe. Set the HFEC instrument to operate between 50 KHz
and 75 KHz. If HFEC method indicates a crack, confirm the crack indication using magnetic particle in-
spection. Refer to SOPM 20-20-01 as an accepted procedure.
(b) An optional magnetic particle inspection can be used. Refer to SOPM 20-20-01 as an accepted procedure.
(c) HFEC crack indications can be confirmed using the magnetic particle inspection. If crack indications are
found with HFEC and could not be confirmed with magnetic particle inspection, the HFEC crack indication
is a non relevant indication due to chrome cracking.
FIGURE 4: MAIN CARGO DOOR - CAM LATCH 1 AND CAM LATCH 2 INSPECTION
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: March 09, 2010
757-52A0091Revision 1 December 19, 2014
45 of 62
BOEING SERVICE BULLETIN 757-52A0091
ALERTALERT

### Page 46 (OCR)

BOEING SERVICE BULLETIN 757-52A0091
ALERT  ALERT
MAIN CARGO DOORWAY
LOWER SILL
LATCH PIN FITTING
ASSEMBLY
(8 LOCATIONS)
(SHOWN WITH OPTIONAL CLIP  LATCH PIN FITTING ASSEMBLY  O LATCH PIN  CROSS BOLT
ASSEMBLY INSTALLED)
1677164
FIGURE 5: MAIN CARGO DOOR - LATCH PIN CROSS BOLT REPLACEMENT
(SHEET 1 OF 2)
Original Issue: March 09, 2010
Revision 1 December 19, 2014  Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright @ Unpublished  757-52A0091
Work - See page 1 for details.  46 of 62

### Page 47

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
More DataQtyIdentificationNameTaskStep
-8NAS6603-24
(BACB30NF3-22 option-
al)
Latch Pin Cross BoltRemove1
Install with BMS 3-
27 corrosion inhibit-
ing material
8BACB30LM3-24
(BACB30LM3-22 option-
al)
Latch Pin Cross BoltInstall (New)2
FIGURE 5: MAIN CARGO DOOR - LATCH PIN CROSS BOLT REPLACEMENT
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: March 09, 2010
757-52A0091Revision 1 December 19, 2014
47 of 62
BOEING SERVICE BULLETIN 757-52A0091
ALERTALERT

### Page 48 (OCR)

BOEING SERVICE BULLETIN 757-52A0091
ALERT  ALERT
MAIN CARGO DOOR
CAM LATCH  8 LOCATIONS) A
1677197
FIGURE 6: MAIN CARGO DOOR - CAM LATCH REPLACEMENT
(SHEET 1 OF 3)
Original Issue: March 09, 2010
Revision 1 December 19, 2014  Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright © Unpublished  757-52A0091
Work - See page 1 for details.  48 of 62

### Page 49 (OCR)

BOEING SERVICE BULLETIN 757-52A0091
ALERT  ALERT
CAM LATCH
CROSS BOLT -
HOLES
• EXISTING
TOOLING
HOLE
1846646
FIGURE 6: MAIN CARGO DOOR - CAM LATCH REPLACEMENT
(SHEET 2 OF 3)
Original Issue: March 09, 2010
Revision 1 December 19, 2014  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  Work - See page 1 for details.  757-52A0091  49 of 62

### Page 50

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
More DataQtyIdentificationNameTaskStep
(a)169-23438-2Cam Latch 1Remove1
(a)1143N8060-1Cam Latch 2Remove
(a)1143N8027-2Cam Latch 3Remove
(a) Gusset must be
removed to allow re-
moval of cam latch
number 4.
169-23439-3Cam Latch 4Remove
(a)169-23439-4Cam Latch 5Remove
(a)1143N8027-1Cam Latch 6Remove
(a)1143N8060-2Cam Latch 7Remove
(a)169-23438-1Cam Latch 8Remove
(a) (b) (d)169-23438-2Cam Latch 1Install (New)2
(a) (b) (c) (d)1143N8060-1Cam Latch 2Install (New)
(a) (b) (d)1143N8027-2Cam Latch 3Install (New)
(a) (b) (d) Gusset
must be removed to
allow installation of
cam latch number 4.
169-23439-3Cam Latch 4Install (New)
(a) (b) (d)169-23439-4Cam Latch 5Install (New)
(a) (b) (d)1143N8027-1Cam Latch 6Install (New)
(a) (b) (c) (d)1143N8060-2Cam Latch 7Install (New)
(a) (b) (d)169-23438-1Cam Latch 8Install (New)
(a) Part numbers and quantities necessary are based on inspection findings.
(b) Use the original removed cam latch as a pattern/template to locate new cross bolt holes. Match hole an-
gularity from existing cam latch.
(c) Cam latch number 2 and cam latch number 7 only have two cross bolt holes.
(d) It is acceptable to install a reworked Cam Latch with the same part number instead of a new part.
FIGURE 6: MAIN CARGO DOOR - CAM LATCH REPLACEMENT
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: March 09, 2010
757-52A0091Revision 1 December 19, 2014
50 of 62
BOEING SERVICE BULLETIN 757-52A0091
ALERTALERT

### Page 51 (OCR)

BOEING SERVICE BULLETIN 757-52A0091
ALERT  ALERT
MAIN CARGO DOORWAY
LOWER SILL
LATCH PIN FITTING
ASSEMBLY
(8 LOCATIONS)
0.91
0.89
LATCH PIN 12
LATCH PIN FITTING ASSEMBLY
(SHOWN WITH OPTIONAL CLIP
ASSEMBLY INSTALLED)
WEAR PLATE  1677201
FIGURE 7: MAIN CARGO DOOR - LATCH PIN REPLACEMENT
(SHEET 1 OF 2)
Original Issue: March 09, 2010
Revision 1 December 19, 2014  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  757-52A0091
Work - See page 1 for details.  51 of 62

### Page 52

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
--6-83137-2Latch PinRemove1
Install latch pin wet with BMS 3-27
corrosion inhibiting material on
faying surfaces. Make sure the
latch pin extends out 0.90 inch +/-
0.01 inch from the wear plate.
-6-83137-2Latch PinInstall (New)2
FIGURE 7: MAIN CARGO DOOR - LATCH PIN REPLACEMENT
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: March 09, 2010
757-52A0091Revision 1 December 19, 2014
52 of 62
BOEING SERVICE BULLETIN 757-52A0091
ALERTALERT

### Page 53 (OCR)

BOEING SERVICE BULLETIN 757-52A0091
ALERT  ALERT
03 C
3) C
03 C
1677216
FIGURE 8: MAIN CARGO DOOR - CAM LATCH REMOVAL AND INSPECTION
(SHEET 1 OF 3)
Original Issue: March 09, 2010
Revision 1 December 19, 2014  Export Controlled ECCN: 9E991 - BOEING  757-52A0091
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  53 of 62

### Page 54 (OCR)

BOEING SERVICE BULLETIN 757-52A0091
ALERT  ALERT
LATCH PIN
(8 LOCATIONS)
CRITICAL AREA ENTIRE
CIRCUMFERENCE
0.3*
CRITICAL AREAS  WEAR PLATE
CAM LATCH (2
C
1677218
FIGURE 8: MAIN CARGO DOOR - CAM LATCH REMOVAL AND INSPECTION
(SHEET 2 OF 3)
Original Issue: March 09, 2010
Revision 1 December 19, 2014  Export Controlled ECCN: 9E991 - BOEING  757-52A0091
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  54 of 62

### Page 55

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
More DataQtyIdentificationNameTaskStep
(a) (b)169-23438-2Cam Latch 1Remove / Keep1
(a) (b)1143N8060-1Cam Latch 2Remove / Keep
(a) (b)1143N8027-2Cam Latch 3Remove / Keep
(a) (b) (c)169-23439-3Cam Latch 4Remove / Keep
(a) (b)169-23439-4Cam Latch 5Remove / Keep
(a) (b)1143N8027-1Cam Latch 6Remove / Keep
(a) (b)1143N8060-2Cam Latch 7Remove / Keep
(a) (b)169-23438-1Cam Latch 8Remove / Keep
Detailed inspection
of the cam latch for
cracks or gouges in
critical areas. (d)
--Cam LatchInspect2
(a) (b) (e)169-23438-2Cam Latch 1Install (Kept)3
(a) (b) (e)1143N8060-1Cam Latch 2Install (Kept)
(a) (b) (e)1143N8027-2Cam Latch 3Install (Kept)
(a) (b) (e)169-23439-3Cam Latch 4Install (Kept)
(a) (b) (e)169-23439-4Cam Latch 5Install (Kept)
(a) (b) (e)1143N8027-1Cam Latch 6Install (Kept)
(a) (b) (e)1143N8060-2Cam Latch 7Install (Kept)
(a) (b) (e)169-23438-1Cam Latch 8Install (Kept)
Detailed inspection
of the latch pin for
cracks or gouges in
critical areas.
86-83137-2Latch PinInspect4
(a) It is important to identify the Cam Latch part locations to ensure the parts are re-installed in correct locations.
Cam latches installed incorrectly may seriously compromise proper door operation.
(b) Part numbers and quantities necessary are based on inspection findings.
(c) Gusset must be removed to allow removal of cam latch number 4.
(d) Only inspect removed cam latch(es).
(e) Do not install kept cam latch if cracked or gouged in critical areas.
FIGURE 8: MAIN CARGO DOOR - CAM LATCH REMOVAL AND INSPECTION
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: March 09, 2010
757-52A0091Revision 1 December 19, 2014
55 of 62
BOEING SERVICE BULLETIN 757-52A0091
ALERTALERT

### Page 56 (OCR)

BOEING SERVICE BULLETIN 757-52A0091
ALERT  ALERT
MAIN CARGO DOORWAY
LOWER SILL
(3) CROSS BOLT
(8 LOCATIONS)
2) LATCH PIN
(8 LOCATIONS)
1) CAM LATCH
(8 LOCATIONS)
WD
1677221
FIGURE 9: MAIN CARGO DOOR - CAM LATCHES, LATCH PINS AND LATCH PIN CROSS BOLTS
INSPECTION
(SHEET 1 OF 2)
Original Issue: March 09, 2010
Revision 1 December 19, 2014  Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright © Unpublished  757-52A0091
Work - See page 1 for details.  56 of 62

### Page 57

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
More DataQtyIdentificationNameTaskStep
General visual in-
spection of the cam
latch.(a)
169-23438-2Cam Latch 1Inspect1
General visual in-
spection of the cam
latch.(a)
1143N8060-1Cam Latch 2Inspect
General visual in-
spection of the cam
latch.(a)
1143N8027-2Cam Latch 3Inspect
General visual in-
spection of the cam
latch.(a)
169-23439-3Cam Latch 4Inspect
General visual in-
spection of the cam
latch.(a)
169-23439-4Cam Latch 5Inspect
General visual in-
spection of the cam
latch.(a)
1143N8027-1Cam Latch 6Inspect
General visual in-
spection of the cam
latch.(a)
1143N8060-2Cam Latch 7Inspect
General visual in-
spection of the cam
latch.(a)
169-23438-1Cam Latch 8Inspect
General visual in-
spection of the latch
pins.(a)
86-83137-2Latch PinInspect2
General visual in-
spection of the latch
pin cross bolts.(a)
8-Cross BoltInspect3
(a) Inspect for broken parts. Also inspect for missing parts.
FIGURE 9: MAIN CARGO DOOR - CAM LATCHES, LATCH PINS AND LATCH PIN CROSS BOLTS
INSPECTION
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: March 09, 2010
757-52A0091Revision 1 December 19, 2014
57 of 62
BOEING SERVICE BULLETIN 757-52A0091
ALERTALERT

### Page 58 (OCR)

BOEING SERVICE BULLETIN 757-52A0091
ALERT  ALERT
• MECHANISN  I CENTER LATCI
FORWARD
LATCH
MECHANISM
AFT LATCH
MECHANISM
NO. 1
NO. 2
NO.4 B  NO. 3 B
NO. 6 B  NO. 5 B
NO. 8  B  NO. 7  B
INBD
1916499
FIGURE 10: MAIN CARGO DOOR - CAM LATCH AND LATCH PIN RIGGING
(SHEET 1 OF 3)
Original Issue: March 09, 2010
Revision 1 December 19, 2014  Export Controlled ECCN: 9E991 - BOEING  757-52A0091
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  58 of 62

### Page 59 (OCR)

BOEING SERVICE BULLETIN 757-52A0091
ALERT  ALERT
CAM LATCH
TYPICAL
C CAM LATCH AXIAL  CENTERLINE  LATCH PIN AXIAL  CENTERLINE
CAM LATCH (1)  1 LATCH PIN
END VIEW
A-A
• 0.025
MAX
0.025-
MAX
0.025
MAX
0.025
MAX
CAM LATCH
C  1915618
FIGURE 10: MAIN CARGO DOOR - CAM LATCH AND LATCH PIN RIGGING
(SHEET 2 OF 3)
Original Issue: March 09, 2010
Revision 1 December 19, 2014  Export Controlled ECCN: 9E991 - BOEING  757-52A0091
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  59 of 62

### Page 60

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
More DataQtyIdentificationNameTaskStep
(a) (b)8-Cam LatchMeasure1
(a) (b)86-83137-2Latch PinMeasure
(c)8-Latch Pin FittingMeasure
(a) During rigging procedure the latch pin is not to contact the cam latch in any direction.
(b) Wrap a single layer of 0.002 inch thick shim stock around latch pins 1 and 8. Use thin tape to keep shim
in place. With latch pins 1 and 8 engaging their respective cam latches, and with latch pins 2 through 7
not contacting their respective cam latches in any direction, adjust if required, latch pin fittings 2 through
7 such that latch pins 2 through 7 axial centerlines and their respective cam latch axial centerlines are
within the tolerance shown.
(c) Adjust latch pin fittings by moving fitting on serrations and by adjusting shim thickness. On the two forward
and two aft cam latches the Latch Pin Fitting/Cam Latch gap is 0.14 +/- 0.01 inch. On the four center cam
latches the Latch Pin Fitting/Cam Latch gap is 0.08 +/- 0.01 inch. Make sure the maximum allowed shim
thickness of 0.20 inch is not exceeded.
FIGURE 10: MAIN CARGO DOOR - CAM LATCH AND LATCH PIN RIGGING
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: March 09, 2010
757-52A0091Revision 1 December 19, 2014
60 of 62
BOEING SERVICE BULLETIN 757-52A0091
ALERTALERT

The text continues at https://openairdocs.org/service-documents/boeing/757-52a0091/file/7282699837d8.md?from=61

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
