# Boeing Alert Service Bulletin 757-53A0103: No revision named

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2016-9502; AD 2017-12-14 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Alert Service Bulletin 757-53A0103](https://openairdocs.org/service-documents/boeing/757-53a0103.md)
- Title as filed: FAA-2016-9502_SB 757-53A0103
- Pages: 41
- PDF: https://openairdocs.org/files/sha256/c8/90/c8907f49034266d8187999e9019027eafc9357ee6976118eb7f26935946fddd8
- Page: https://openairdocs.org/service-documents/boeing/757-53a0103/file/c8907f490342

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Commercial 
Airplanes
757
Service Bulletin
ALERT
Number: 757-53A0103
Original Issue: June 22, 2016
ATA System: 5333 5363
SUBJECT: FUSELAGE - Section 43 and Section 46 - Structure - Inspection and Modification of
Open Holes on Frame Webs Between Stringers S-20 and S-25
Export of this technology is controlled under the United States Export Administration Regulations (EAR) (15
CFR 300-774). An export license may be required before it is used for development, production or use by foreign
persons from specific countries. The controller of this data has the individual responsibility to abide by all export
laws.
9E991ECCN:
BOEING PROPRIETARY, CONFIDENTIAL AND/OR TRADE SECRET
Copyright © 2016 Boeing.
Unpublished Work. All Rights Reserved.
Treatment of this document and its content is governed by contract with Boeing. Rights to use this document
are licensed on a per aircraft basis and such rights may not be transferable. For more information, contact The
Boeing Company.
Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner,
BBJ, DC-8, DC-9, DC-10, KC-10, KC-46, KDC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8, Poseidon and
Boeing liveries are all trademarks owned by The Boeing Company; and no trademark license is granted in
connection with this document unless provided in writing by Boeing.
Original Issue: June 22, 2016
757-53A0103
1 of 41
3.0

### Page 2

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 22, 2016
757-53A0103
2 of 41
BOEING SERVICE BULLETIN 757-53A0103
ALERTALERT
BLANK PAGE

### Page 3

Table of Contents
Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1. PLANNING INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
A. Effectivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1. Airplanes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2. Spares Affected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
B. Concurrent Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
C. Reason . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
D. Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
E. Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
F. Approval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
G. Manpower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
H. Weight and Balance Changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
I. Electrical Load Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
J. References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
1. Existing Data: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2. Data Supplied with this Service Bulletin: . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3. Installation Drawings Used in the Preparation of this Service Bulletin: . . . . . . . . . . . 15
K. Publications Affected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
L. Interchangeability and Intermixability of Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
M. Software Accomplishment Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2. MATERIAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
A. Material - Price and Availability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
B. Industry Support Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
C. Parts Necessary for Each Airplane . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
1. Kits/Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2. Parts and Materials Supplied by the Operator . . . . . . . . . . . . . . . . . . . . . . . . 17
3. Parts Modified and Reidentified . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
4. Parts Removed and Not Replaced . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
D. Parts Necessary to Change Spares . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
E. Special Tooling - Price and Availability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
F. Special Tooling Necessary to do this Service Bulletin . . . . . . . . . . . . . . . . . . . . . . . 18
3. ACCOMPLISHMENT INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
A. GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
B. WORK INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
FIGURE 1: OPEN HOLE HIGH FREQUENCY EDDY CURRENT INSPECTIONS BETWEEN STRINGERS
S-20 AND S-25 FROM STA 440 TO STA 820 AND FROM STA 1300 TO STA 1701 [Group 1]
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
FIGURE 2: OPEN HOLE HIGH FREQUENCY EDDY CURRENT INSPECTIONS BETWEEN STRINGERS
S-20 AND S-25 FROM STA 440 TO STA 820 AND FROM STA 1300 TO STA 1701 [Group 2]
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
FIGURE 3: MODIFICATION OF FRAME WEB BETWEEN STRINGERS S-20 AND S-25 FROM STA 440
TO STA 820 AND FROM STA 1300 TO STA 1701  [Group 1] . . . . . . . . . . . . . . . . 32
FIGURE 4: MODIFICATION OF FRAME WEB BETWEEN STRINGERS S-20 AND S-25 FROM STA 440
TO STA 820 AND FROM STA 1300 TO STA 1701  [Group 2] . . . . . . . . . . . . . . . . 36
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 22, 2016
757-53A0103
3 of 41
BOEING SERVICE BULLETIN 757-53A0103
ALERTALERT

### Page 4

APPENDIX A: LOGIC DIAGRAM FOR PARAGRAPH 1.E. COMPLIANCE, TABLE 1: INSPECTION AND
MODIFICATION OF OPEN HOLES ON FRAME WEBS BETWEEN STRINGERS S-20 AND
S-25 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 22, 2016
757-53A0103
4 of 41
BOEING SERVICE BULLETIN 757-53A0103
ALERTALERT

### Page 5

Commercial 
Airplanes
757
Service Bulletin
ALERT
SummaryNumber: 757-53A0103Original Issue: June 22, 2016
ATA System: 5333 5363
SUBJECT: FUSELAGE - Section 43 and Section 46 - Structure - Inspection and Modification of
Open Holes on Frame Webs Between Stringers S-20 and S-25
THIS DOCUMENT IS SENT TO THE OPERATORS OF RECORD OF THE AIRPLANES SHOWN IN
PARAGRAPH 1.A., EFFECTIVITY. IF AN AIRPLANE HAS BEEN LEASED OR SOLD, SEND THIS DOCUMENT
TO THE NEW OPERATOR. IF APPLICABLE SPARES HAVE BEEN SOLD, SEND THIS DOCUMENT TO THE
NEW OWNER.
CONCURRENT REQUIREMENTS
None.
BACKGROUND
This service bulletin is sent to inspect the frame webs for any open coordinating holes, tooling holes and insulation
blanket attachment holes. The affected frame webs are between stringers S-20 and S-25 on the left side and
right side, from STA 440 to STA 820 and from STA 1300 to STA 1701. Do an open hole eddy current inspection
of all open coordinating holes, tooling holes and insulation blanket attachment holes found during the general
visual inspection. If this service bulletin is not done, fatigue cracking could adversely affect the structural integrity
of the airplane.
Boeing found that 757 airplanes, line number 1 through 174, have open coordinating holes, tooling holes and
insulation blanket attachment holes in the frame webs which were not filled during production. A Widespread
Fatigue Damage (WFD) analysis on the open holes identified a need for inspections at these locations.
There have been no reports of frame web cracking at open hole locations from operators. Cracking was found
on a fatigue test article, where WFD analysis identified the need for the inspection.
Boeing Fleet Team Digest (FTD) 757 FTD 53-15004 is related to this service bulletin.
The frame webs have been determined to be structure that is susceptible to Widespread Fatigue Damage (WFD).
This table is provided to operators for planning purposes only. Refer to the applicable sections for more
information.
ReferenceAffectedPlanning Data
Paragraph 1.A.2., Spares AffectedNoSpares Affected
Paragraph 1.E., Compliance and Paragraph
1.F., Approval
YesAD Related
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 22, 2016
757-53A0103
5 of 41

### Page 6

ReferenceAffectedPlanning Data
Paragraph 1.H., Weight and Balance ChangesYesWeight and Balance Change
Paragraph 1.I., Electrical Load DataNoElectrical Load Changed
Paragraph 1.K., Publications AffectedNoPublications Affected
Paragraph 1.K., Publications AffectedNoAirplane Flight Operations Affected (Flight Crew
Operations Manual and/or FAA Approved Air-
plane Flight Manual)
Paragraph 2.C.1., Kits/PartsNoKits/Parts Required
Paragraph 2.C.2., Parts and Materials Supplied
by the Operator
YesOperator Supplied Parts/Material
Paragraph 2.F., Special Tooling Necessary to
do this Service Bulletin
NoSpecial Tooling Required
ACTION
Do an Inspection of the frame webs for any open coordinating holes, tooling holes and insulation blanket
attachment holes. Do an open hole eddy current inspection for any crack on all open coordinating holes, tooling
holes and insulation blanket attachment holes between stringers S-20 and S-25 on the left side and right side,
from STA 440 to STA 820 and from STA 1300 to STA 1701. If any crack is found, contact The Boeing Company
for repair instructions and do the repair. If no crack is found, repeat the inspections and do the preventative
modification at the compliance time given in Paragraph 1.E., Compliance.
EFFECTIVITY
757-200/200PF Airplanes. Refer to Paragraph 1.A.1., Airplanes, for the list of affected airplanes.
COMPLIANCE
The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to this service
bulletin. The Airworthiness Directive will make the compliance tasks and times given in this service bulletin
mandatory.
Refer to Paragraph 1.E., Compliance.
INDUSTRY SUPPORT INFORMATION
Boeing warranty remedies are not available for the inspection and modification given in this service bulletin.
MANPOWER
Refer to Paragraph 1.G., Manpower.
MATERIAL INFORMATION
Operator Supplied Parts/Materials.
Refer to Paragraph 2.A., Material - Price and Availability.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 22, 2016
757-53A0103
6 of 41
BOEING SERVICE BULLETIN 757-53A0103
ALERTALERT

### Page 7 (OCR)

BOEING SERVICE BULLETIN 757-53A0103
ALERT  ALERT
STA
440
STA
820  STA
1300
STA
1701
BETWEEN STF  S S-20 TO S-25, FROM STA 440 TO STA 820 AND
FROM STA 1300  TA 1701, INSPECT THE FRAME WEBS FOR ANY
OPEN COORDINA  GHOLES, TOO  LING HOLES AND INSULATION
BLANKET AT  NT HOLES. DO  I OPEN HOLE HIGH
FREQUENCY EDDY CURRENT INSPECTION OF ALL OPEN HOLES FOR
ANY CRACK
2482883
Original Issue: June 22, 2016
Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright © Unpublished  757-53A0103
Work - See page 1 for details.  7 of 41

### Page 8

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 22, 2016
757-53A0103
8 of 41
BOEING SERVICE BULLETIN 757-53A0103
ALERTALERT
BLANK PAGE

### Page 9

Commercial 
Airplanes
757
Service Bulletin
ALERT
Number: 757-53A0103
Original Issue: June 22, 2016
ATA System: 5333 5363
SUBJECT: FUSELAGE - Section 43 and Section 46 - Structure - Inspection and Modification of
Open Holes on Frame Webs Between Stringers S-20 and S-25
THIS DOCUMENT IS SENT TO THE OPERATORS OF RECORD OF THE AIRPLANES SHOWN IN
PARAGRAPH 1.A., EFFECTIVITY. IF AN AIRPLANE HAS BEEN LEASED OR SOLD, SEND THIS DOCUMENT
TO THE NEW OPERATOR. IF APPLICABLE SPARES HAVE BEEN SOLD, SEND THIS DOCUMENT TO THE
NEW OWNER.
1.    PLANNING INFORMATION
A. Effectivity
1. Airplanes
Refer to Service Bulletin Index D624N001 Part 3 for Airplane Variable Number, Line Number, and
Serial Number data.
This service bulletin is applicable to 757-200/-200PF Airplanes, line numbers 1 - 174 in 2 Groups.
The Variable Numbers and Group Information for the applicable airplanes is given below.
DESCRIPTIONCONFIGURATIONGROUP
Airplane line numbers 1 through 174 without a number 3 cargo door.-1
Airplane line numbers 1 through 174 with a number 3 cargo door.-2
Airplane Models:
757-200, 757-200PF
GroupVariable Number
1NA001 - NA028
1NA191 - NA197
2NA201 - NA231
2NA391 - NA394
1NA401 - NA408
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 22, 2016
757-53A0103
9 of 41

### Page 10

GroupVariable Number
1NA441 - NA443
1NA501 - NA537
1NB001 - NB004
1NB021 - NB023
1NB036 - NB038
1NB051 - NB053
1NB061 - NB063
1NB071 - NB072
1NC001 - NC028
1NC041 - NC042
1NC901 - NC905
1ND001 - ND002
1ND891
2. Spares Affected
None.
B. Concurrent Requirements
None.
C. Reason
This service bulletin is sent to inspect the frame webs for any open coordinating holes, tooling holes
and insulation blanket attachment holes. The affected frame webs are between stringers S-20 and
S-25 on the left side and right side, from STA 440 to STA 820 and from STA 1300 to STA 1701. Do
an open hole eddy current inspection of all open coordinating holes, tooling holes and insulation blanket
attachment holes found during the general visual inspection. If this service bulletin is not done, fatigue
cracking could adversely affect the structural integrity of the airplane.
Boeing found that 757 airplanes, line number 1 through 174, have open coordinating holes, tooling
holes and insulation blanket attachment holes in the frame webs which were not filled during production.
A Widespread Fatigue Damage (WFD) analysis on the open holes identified a need for inspections at
these locations.
There have been no reports of frame web cracking at open hole locations from operators. Cracking
was found on a fatigue test article, where WFD analysis identified the need for the inspection.
Boeing Fleet Team Digest (FTD) 757 FTD 53-15004 is related to this service bulletin.
The frame webs have been determined to be structure that is susceptible to Widespread Fatigue
Damage (WFD).
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 22, 2016
757-53A0103
10 of 41
BOEING SERVICE BULLETIN 757-53A0103
ALERTALERT

### Page 11

D. Description
Do an Inspection of the frame webs for any open coordinating holes, tooling holes and insulation blanket
attachment holes. Do an open hole eddy current inspection for any crack on all open coordinating
holes, tooling holes and insulation blanket attachment holes between stringers S-20 and S-25 on the
left side and right side, from STA 440 to STA 820 and from STA 1300 to STA 1701. If any crack is
found, contact The Boeing Company for repair instructions and do the repair. If no crack is found,
repeat the inspections and do the preventative modification at the compliance time given in Paragraph
1.E., Compliance.
The work in this service bulletin is done in the maintenance zone(s) given below.
Group 1:
Affected Maintenance Zones
ZoneModel
119, 121, 122, 153, 154, 161, 162, 165, 166757-200, 757-200PF
Group 2:
Affected Maintenance Zones
ZoneModel
119, 121, 122, 153, 154, 161, 162, 165, 166757-200
E. Compliance
The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to
this service bulletin. The Airworthiness Directive will make the compliance tasks and times given in this
service bulletin mandatory.
A logic diagram showing compliance tasks and compliance times is included as an aid in APPENDIX
A.
Do the required actions in accordance with Paragraph 3. Accomplishment Instructions.
When more than one OPTION is given for a CONDITION, do only one of the OPTION numbers. When
more than one ACTION is given for a CONDITION number or an OPTION number, do all of the ACTION
numbers for that CONDITION number or OPTION number.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 22, 2016
757-53A0103
11 of 41
BOEING SERVICE BULLETIN 757-53A0103
ALERTALERT

### Page 12

Table 1: Inspection and Modification of Open Holes on Frame Webs Between Stringers S-20 and S-25
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Within 3,000
flight cycles af-
ter the original
issue date of
this service bul-
letin.
Before 28,000
total flight cy-
cles.
Do PART 2: INSPEC-
TION OF THE FRAME
WEBS BETWEEN
STRINGERS S-20 AND
S-25 for any crack. (a)
All Airplanes.
--Before further
flight.
CONDITION 1 (ACTION
1): Contact The Boeing
Company for repair in-
structions and do the re-
pair.
CONDITION 1: ANY
CRACK FOUND.
12,000 flight cy-
cles. (b)
--CONDITION 1 (ACTION
2): Repeat PART 2: IN-
SPECTION OF THE
FRAME WEBS BE-
TWEEN STRINGERS S-
20 AND S-25 at all unre-
paired locations. (a)
--Before 59,000
total flight cy-
cles.
CONDITION 1 (ACTION
3): Do PART 3: MODIFI-
CATION OF THE FRAME
WEBS BETWEEN
STRINGERS S-20 AND
S-25 at all unrepaired lo-
cations. (b)
12,000 flight cy-
cles. (b)
--CONDITION 2 (ACTION
1): Repeat PART 2: IN-
SPECTION OF THE
FRAME WEBS BE-
TWEEN STRINGERS S-
20 AND S-25 at all open
hole locations. (a)
CONDITION 2: NO
CRACK FOUND.
--Before 59,000
total flight cy-
cles.
CONDITION 2 (ACTION
2): Do PART 3: MODIFI-
CATION OF THE FRAME
WEBS BETWEEN
STRINGERS S-20 AND
S-25 at all open hole loca-
tions. (b)
(a) It is not necessary to do inspections in accordance with this service bulletin at any coordinating holes,
tooling holes, and insulation blanket holes that have been filled with an aluminum rivet, filled in accordance
with 757-200 SRM 53-00-07 Repair 5 or 757-200PF SRM 53-00-07 Repair 5, or have been used as part
of a Boeing Company approved repair via FAA form 8100-9 or 8110-3.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 22, 2016
757-53A0103
12 of 41
BOEING SERVICE BULLETIN 757-53A0103
ALERTALERT

### Page 13

Table 1: Inspection and Modification of Open Holes on Frame Webs Between Stringers S-20 and S-25
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
(b) Accomplishment of PART 3: MODIFICATION OF THE FRAME WEBS BETWEEN STRINGERS S-20
AND S-25 is terminating action to the repeat inspections at modified locations only.
F. Approval
This service bulletin was examined by the Federal Aviation Administration (FAA). The changes specified
in this service bulletin comply with the applicable regulations and are FAA approved, as well as European
Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved
airplanes listed in the service bulletin effectivity. This service bulletin and its approval were based on
the airplane in its original Boeing delivery configuration or as modified by other approved Boeing
changes.
If an airplane has a non-Boeing modification or repair that affects a component or system also affected
by this service bulletin, the operator is responsible for obtaining appropriate regulatory agency approval
before incorporating this service bulletin.
G. Manpower
The table below shows an estimate of the task hours necessary to do this inspection and modification
for each airplane. This estimate is for direct labor only, done by an experienced crew. Adjust the estimate
with operator task hour data if necessary. The estimate does not include lost time. These are some
examples of lost time:
• Time to adjust to the workplace
• Time to schedule the work
• Time to inspect the work
• Time to cure the materials
• Time to make the parts
• Time to find the tools.
Group 1:
Elapsed HoursTask HoursNumber of PersonsTask
16.1532.302Open Access
2.752.751FIGURE 1
0.10 (a)0.10 (a)1FIGURE 3
16.1532.302Close Access
35.0567.35TOTAL FOR EACH AIRPLANE
(a) Estimate given is per hole and not included in total shown. Multiply the number
of holes that require the work in figure 3 by the estimate given and add to total
shown to arrive at a revised total required.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 22, 2016
757-53A0103
13 of 41
BOEING SERVICE BULLETIN 757-53A0103
ALERTALERT

### Page 14

Group 2:
Elapsed HoursTask HoursNumber of PersonsTask
16.1532.302Open Access
2.602.601FIGURE 2
0.10 (a)0.10 (a)1FIGURE 4
16.1532.302Close Access
34.9067.20TOTAL FOR EACH AIRPLANE
(a) Estimate given is per hole and not included in total shown. Multiply the number
of holes that require the work in figure 4 by the estimate given and add to total
shown to arrive at a revised total required.
H. Weight and Balance Changes
Change in Moment
(Pound-Inches)
Change in Weight
(Pounds)Airplane
+1,433.2+1.4Group 1
+1,355.7+1.3Group 2
I. Electrical Load Data
Not changed.
J. References
1. Existing Data:
a. Service Bulletin Index D624N001
b. Standard Overhaul Practices Manual (SOPM) 20-50-01
c. 757 Aircraft Maintenance Manual (AMM) 25-50-02, 25-50-03, 25-50-07, 52-34-00
d. 757 Fleet Team Digest (FTD) 53-15004
e. 757 Non-Destructive Testing (NDT) Manual Part 6, 51-00-16
f. 757-200 Structural Repair Manual (SRM) 51-30-01, 51-40-02, 53-00-07
g. 757-200PF Structural Repair Manual (SRM) 51-30-01, 51-40-02, 53-00-07
2. Data Supplied with this Service Bulletin:
None.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 22, 2016
757-53A0103
14 of 41
BOEING SERVICE BULLETIN 757-53A0103
ALERTALERT

### Page 15

3. Installation Drawings Used in the Preparation of this Service Bulletin:
TitleDrawing Number
STRINGER DIAGRAM BODY MODEL 757140N1530
BODY SECTION 43, TOP ASSEMBLY (a)143N0001
BODY SECTION 46, TOP ASSEMBLY (b)146N0001
CARGO DOOR STRUCTURES MAJOR MODEL MANAGEMENT,
COLLECTOR, MOD (c)
657N0082
FIRST STAGE, LOWER LOBE ASSY - SECT 46 (d)146N0200
NO. 4 PASSENGER DOOR, PANEL ASSEMBLY - STA 1621-1720.
(e)
146N0300
(a) Used for Frame Installation drawings from Station 440 to Station 820 for 757-200 air-
planes without Special Freighter modification.
(b) Used for Frame Installation drawings from Station 1300 to Station 1701, except the
door cutout frames.
(c) Used for Frame Installation drawings from Station 440 to Station 820 for 757-200
Special Freighter modification
(d) Used for Number 3 Cargo door cutout frames.
(e) Used for Number 2 Cargo door cutout frames.
The table above lists applicable drawings used to prepare this service bulletin. The drawings are
not necessary to make the specified changes, and are not supplied with this service bulletin. The
drawings may not be applicable to all airplane configurations or operators.
K. Publications Affected
1. Publications:
None.
2. Damage Tolerance Based Structural Inspections:
Boeing has evaluated the repairs and/or changes in this service bulletin for effects on Fatigue
Critical Structure (FCS) and for changes to Damage Tolerance Inspections (DTI) required in the
Maintenance Program. This service bulletin affects FCS but no new DTIs are necessary.
L. Interchangeability and Intermixability of Parts
Accomplishment of this service bulletin does not affect interchangeability or intermixability of parts.
M. Software Accomplishment Summary
Not affected.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 22, 2016
757-53A0103
15 of 41
BOEING SERVICE BULLETIN 757-53A0103
ALERTALERT

### Page 16

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 22, 2016
757-53A0103
16 of 41
BOEING SERVICE BULLETIN 757-53A0103
ALERTALERT
BLANK PAGE

### Page 17

2.    MATERIAL INFORMATION
A. Material - Price and Availability
None.
B. Industry Support Information
Boeing warranty remedies are not available for the inspection and modification given in this service
bulletin.
C. Parts Necessary for Each Airplane
1. Kits/Parts
None.
2. Parts and Materials Supplied by the Operator
The following parts or materials are necessary to do the change in this service bulletin. Parts and
materials in the manuals given in Paragraph 1.J., References, can also be necessary. Examine
operator part and material supply to make sure all necessary parts and materials are available.
NotesNameQTYPart Number /
Specification
(a) (b)RIVET, MODIFIED UNIVERSAL
HEAD, CLOSE TOLERANCE
SHANK
300BACR15FT7AD( )
(a) (b)RIVET, MODIFIED UNIVERSAL
HEAD, CLOSE TOLERANCE
SHANK
300BACR15FT8AD( )
(a) (b)RIVET, MODIFIED UNIVERSAL
HEAD, CLOSE TOLERANCE
SHANK
100BACR15FT10AD( )
(a) (b)RIVET, MODIFIED UNIVERSAL
HEAD, CLOSE TOLERANCE
SHANK
100BACR15FT11AD( )
(a) Refer to 757 Structural Repair Manual Chapter 51 for alternate fasteners.
(b) Quantity shown is recommended amount to stock for each aircraft to do the modification.
Use as required. Typical grip lengths from BACR15FT()AD3R5 to BACR15FT()AD7.
3. Parts Modified and Reidentified
None.
4. Parts Removed and Not Replaced
None.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 22, 2016
757-53A0103
17 of 41
BOEING SERVICE BULLETIN 757-53A0103
ALERTALERT

### Page 18

D. Parts Necessary to Change Spares
None.
E. Special Tooling - Price and Availability
None.
F. Special Tooling Necessary to do this Service Bulletin
No special tools or equipment are necessary to do the change in this service bulletin. But, maintenance
and overhaul tools in the manuals given in Paragraph 1.J., References, can be necessary. Examine
operator tool supply to make sure all necessary tools are available.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 22, 2016
757-53A0103
18 of 41
BOEING SERVICE BULLETIN 757-53A0103
ALERTALERT

### Page 19

3.    ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL INFORMATION
CAUTION: KEEP THE WORK AREA, WIRES AND ELECTRICAL BUNDLES CLEAN OF METAL
PARTICLES OR CONTAMINATION WHEN YOU USE TOOLS. UNWANTED MATERIAL,
METAL PARTICLES OR CONTAMINATION CAUGHT IN WIRE BUNDLES CAN CAUSE
DAMAGE TO THE BUNDLES. DAMAGED WIRE BUNDLES CAN CAUSE SPARKS OR
OTHER ELECTRICAL DAMAGE.
NOTE: 1. Manual titles are referred to by acronyms. Refer to Paragraph 1.J., References, for
definition of the acronyms.
2. Obey all of the warnings and cautions given in the specified manual sections.
3. Unless shown differently, these dimensions and tolerances are used:
– Linear dimensions are in inches
– Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus
or minus 0.03 inch
– Tolerance on rivet and bolt edge margin is plus or minus 0.05 inch
– Angular tolerance is plus or minus 2 degrees
– Hole dimensions for standard solid rivets and fasteners are in Structural Repair
Manual (SRM) Chapter 51
– Torque Values:
— Values for structural fasteners are given in 757 Structural Repair Manual,
Chapter 51.
— Values for airframe maintenance tasks are included in Chapter 20 of 757
Aircraft Maintenance Manual (AMM).
4. Use the approved fastener, process and material substitutions in accordance with
SRM Chapter 51.
5. If the length of any fastener specified in this service bulletin does not meet installation
standards given in SRM Chapter 51, then a fastener of the same specification, or
an approved substitute, with a length which meets the installation standards given
in SRM Chapter 51 may be used. In addition, washers may be installed for fastener
grip length in accordance with SRM Chapter 51. Refer to SOPM 20-50-01 for alternate
full threaded fasteners (screws) needed for installation in this service bulletin.
6. These work instructions refer to procedures included in other Boeing documents.
When the words "refer to" are used and the operator has an accepted alternative
procedure, the accepted alternative procedure can be used. When the words "in
accordance with" are included in the instruction, the procedure in the Boeing document
must be used.
7. Boeing Service Letter 757-SL-51-022, Damage Reporting and Repair Plan/Design
Guidelines, is an acceptable procedure to request information from Boeing for
additional structural repair instructions. The Service Letter describes what information
must be provided to Boeing before a structural repair can be provided.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 22, 2016
757-53A0103
19 of 41
BOEING SERVICE BULLETIN 757-53A0103
ALERTALERT

### Page 20

8. Refer to APPENDIX A for a logic diagram. The Logic diagram provided as an aid
only. Information contained in Paragraph 1.E., Compliance is the primary source for
compliance times. Information in Paragraph 3.B., Work Instructions is the primary
source for tasks required for compliance.
9. If it is necessary to remove more parts for access, you can remove those parts. If
you can get access without removing identified parts, it is not necessary to remove
all of the identified parts. Jacking and shoring limitations must be observed.
10. Use of colors in Figures is based on guidance from the ATA e-Business Program
(ATA) iSpec 2200.
11. When more than one OPTION is given for a CONDITION, do only one of the OPTION
numbers. When more than one ACTION is given for a CONDITION number or an
OPTION number, do all of the ACTION numbers for that CONDITION number or
OPTION number.
12. The compliance times for the actions in Paragraph 3.B., WORK INSTRUCTIONS
are in Paragraph 1.E., Compliance.
13. Some steps in the Work Instructions are labeled as Required for Compliance (RC).
If this service bulletin is mandated by an Airworthiness Directive (AD), then the steps
labeled as RC, including sub-steps under an RC step and any figures identified in
an RC step, must be done to comply with the AD. An Alternative Method of
Compliance (AMOC) is required for any deviations to RC steps, including sub-steps
and identified figures. Steps not labeled as RC may be deviated from using accepted
methods in accordance with the operator's maintenance or inspection program without
obtaining approval of an AMOC. This is provided that the RC steps, including
sub-steps and identified figures, can still be done as specified, and the airplane can
be put back in an airworthy condition.
B. WORK INSTRUCTIONS
1. Do PART 1: OPEN ACCESS OF FORWARD AND AFT CARGO COMPARTMENTS.
2. RC - Do PART 2: INSPECTION OF THE FRAME WEBS BETWEEN STRINGERS S-20 AND S-25
for any crack.
NOTE: It is not necessary to do inspections in accordance with this service bulletin at any
coordinating holes, tooling holes, and insulation blanket holes that have been filled with
an aluminum rivet, filled in accordance with 757-200 SRM 53-00-07 Repair 5 or 757-200PF
SRM 53-00-07 Repair 5, or have been used as part of a Boeing Company approved
repair via FAA form 8100-9 or 8110-3.
a. CONDITION 1: ANY CRACK FOUND.
(1) CONDITION 1 (ACTION 1): Contact The Boeing Company for repair instructions and do
the repair.
(2) CONDITION 1 (ACTION 2): Repeat PART 2: INSPECTION OF THE FRAME WEBS
BETWEEN STRINGERS S-20 AND S-25 at all unrepaired locations at the time specified
in Paragraph 1.E., Compliance.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 22, 2016
757-53A0103
20 of 41
BOEING SERVICE BULLETIN 757-53A0103
ALERTALERT

### Page 21

NOTE: It is not necessary to do inspections in accordance with this service bulletin at
any coordinating holes, tooling holes, and insulation blanket holes that have
been filled with an aluminum rivet, filled in accordance with 757-200 SRM
53-00-07 Repair 5 or 757-200PF SRM 53-00-07 Repair 5, or have been used
as part of a Boeing Company approved repair via FAA form 8100-9 or 8110-3.
NOTE: Accomplishment of PART 3: MODIFICATION OF THE FRAME WEBS BETWEEN
STRINGERS S-20 AND S-25 is terminating action for the repetitive inspection
requirements at modified locations only.
(3) CONDITION 1 (ACTION 3): Do PART 3: MODIFICATION OF THE FRAME WEBS
BETWEEN STRINGERS S-20 AND S-25 at all unrepaired locations at the time specified
in Paragraph 1.E., Compliance
b. CONDITION 2: NO CRACK FOUND.
(1) CONDITION 2 (ACTION 1): Repeat PART 2: INSPECTION OF THE FRAME WEBS
BETWEEN STRINGERS S-20 AND S-25 at all open hole locations at the time specified
in Paragraph 1.E., Compliance.
NOTE: It is not necessary to do inspections in accordance with this service bulletin at
any coordinating holes, tooling holes, and insulation blanket holes that have
been filled with an aluminum rivet, filled in accordance with 757-200 SRM
53-00-07 Repair 5 or 757-200PF SRM 53-00-07 Repair 5, or have been used
as part of a Boeing Company approved repair via FAA form 8100-9 or 8110-3.
NOTE: Accomplishment of PART 3: MODIFICATION OF THE FRAME WEBS BETWEEN
STRINGERS S-20 AND S-25 is terminating action for the repetitive inspection
requirements at modified locations only.
(2) CONDITION 2 (ACTION 2): Do PART 3: MODIFICATION OF THE FRAME WEBS
BETWEEN STRINGERS S-20 AND S-25 at all open hole locations at the time specified
in Paragraph 1.E., Compliance.
3. Do PART 4: CLOSE ACCESS OF FORWARD AND AFT CARGO COMPARTMENTS.
4. Put the airplane back to a serviceable condition.
PART 1: OPEN ACCESS OF FORWARD AND AFT CARGO COMPARTMENTS
1. Open the cargo doors to get access to the forward cargo compartment and the aft cargo
compartment. Refer to 757 AMM 52-34-00 as an accepted procedure.
2. Remove and keep all forward and aft cargo compartment sidewall linings. Refer to 757 AMM
25-50-02 as an accepted procedure.
3. Remove and keep the forward bulkhead lining for the forward cargo compartment and remove
and keep the aft bulkhead lining for the bulk cargo compartment. Refer to 757 AMM 25-50-03 as
an accepted procedure.
4. Remove and keep the insulation blankets at the forward and aft cargo compartment sidewalls.
Refer to 757 AMM 25-50-07 as an accepted procedure.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 22, 2016
757-53A0103
21 of 41
BOEING SERVICE BULLETIN 757-53A0103
ALERTALERT

### Page 22

PART 2: INSPECTION OF THE FRAME WEBS BETWEEN STRINGERS S-20 AND S-25
1. Group 1:
Inspect the frame webs for any open coordinating holes, tooling holes, and insulation blanket holes
between S-20 and S-25 on the left side from STA 440 to STA 820 and from STA 1300 to STA
1701; and on the right side from STA 440 to STA 540, from STA 640 to STA 820, from STA 1300
to STA 1360, and from STA 1460 to STA 1701. Do an open hole high frequency eddy current
inspection (HFEC) for any crack in the open coordinating holes, tooling holes, and insulation
attachment blanket holes in accordance with FIGURE 1.
Group 2:
Inspect the frame webs for any open coordinating holes, tooling holes, and insulation blanket holes
between S-20 and S-25 on the left side from STA 440 to STA 820 and from STA 1300 to STA
1701; and on the right side from STA 440 to STA 540, from STA 640 to STA 820, from STA 1300
to STA 1360, from STA 1460 to STA 1520, and from STA 1620 to STA 1701. Do an open hole
high frequency eddy current inspection (HFEC) for any crack in the open coordinating holes, tooling
holes, and insulation attachment blanket holes in accordance with FIGURE 2.
PART 3: MODIFICATION OF THE FRAME WEBS BETWEEN STRINGERS S-20 AND S-25
1. Group 1:
Inspect the frame webs for any open coordinating holes, tooling holes, and insulation blanket holes
between S-20 and S-25 on the left side from STA 440 to STA 820 and from STA 1300 to STA
1701; and on the right side from STA 440 to STA 540, from STA 640 to STA 820, from STA 1300
to STA 1360, and from STA 1460 to STA 1701. Do an open hole high frequency eddy current
inspection (HFEC) for any crack in the open coordinating holes, tooling holes, and insulation
attachment blanket holes in accordance with FIGURE 1.
Group 2:
Inspect the frame webs for any open coordinating holes, tooling holes, and insulation blanket holes
between S-20 and S-25 on the left side from STA 440 to STA 820 and from STA 1300 to STA
1701; and on the right side from STA 440 to STA 540, from STA 640 to STA 820, from STA 1300
to STA 1360, from STA 1460 to STA 1520, and from STA 1620 to STA 1701. Do an open hole
high frequency eddy current inspection (HFEC) for any crack in the open coordinating holes, tooling
holes, and insulation attachment blanket holes in accordance with FIGURE 2.
a. Based on inspection results, do the following:
(1) If any crack is found at an open hole, contact The Boeing Company for repair instructions
and do the repair.
(2) Group 1:
If no crack is found at an open hole modify all open hole locations in accordance with
FIGURE 3.
Group 2:
If no crack is found at an open hole modify all open hole locations in accordance with
FIGURE 4.
PART 4: CLOSE ACCESS OF FORWARD AND AFT CARGO COMPARTMENTS
1. Install the kept forward and aft cargo compartment sidewall insulation blankets. Refer to 757 AMM
25-50-07 as an accepted procedure.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 22, 2016
757-53A0103
22 of 41
BOEING SERVICE BULLETIN 757-53A0103
ALERTALERT

### Page 23

2. Install the kept forward bulkhead lining for the forward cargo compartment and install the kept aft
bulkhead lining for the bulk cargo compartment. Refer to 757 AMM 25-50-03 as an accepted
procedure.
3. Install the kept forward and aft cargo compartment sidewall linings. Refer to 757 AMM 25-50-02
as an accepted procedure.
4. Close all cargo doors. Refer to 757 AMM 52-34-00 as an accepted procedure.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 22, 2016
757-53A0103
23 of 41
BOEING SERVICE BULLETIN 757-53A0103
ALERTALERT

### Page 24 (OCR)

BOEING SERVICE BULLETIN 757-53A0103
ALERT  ALERT
This Figure applies only to: Group 1.
STA  STA  STA  STA  STA  STA
440  560  620  740  820  920
- S-13L
- S-17L
• S-20L
- S-25L
- S-28L
Ç-
- S-28 R
- S-25R
-S-20R
- S-17R
- S-13R
NO. 1 CARGO DOOR
FRAME INSPECTION AREAS
A-A  2465125
FIGURE 1: OPEN HOLE HIGH FREQUENCY EDDY CURRENTINSPECTIONS BETWEEN STRINGERS S-20
AND S-25 FROM STA 440 TO STA 820 AND FROM STA 1300 TO STA 1701
(SHEET 1 OF 4)
Original Issue: June 22, 2016
PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  757-53A0103
Work - See page 1 for details.  24 of 41

### Page 25 (OCR)

BOEING SERVICE BULLETIN 757-53A0103
ALERT  ALERT
PRESSURE  RELIEF VALVES  PRESSURE  CONTROL VALVE
STA  STA  STA  STA
1180  1300  1360  1701
• STA
S-13L -  1720
S-17L -
S-20L -
S-25L -
S-29L
S-29R
S-25R-
S-20R-
S-17R-
S-13R-
NO. 2 CARGO
DOOR
FRAME INSPECTION AREAS
B-B
2469912
FIGURE 1: OPEN HOLE HIGH FREQUENCY EDDY CURRENT INSPECTIONS BETWEEN STRINGERS S-20
AND S-25 FROM STA 440 TO STA 820 AND FROM STA 1300 TO STA 1701
(SHEET 2 OF 4)
Original Issue: June 22, 2016
Export Controlled ECCN: 9E991 - BOEING  757-53A0103
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  25 of 41

### Page 26 (OCR)

BOEING SERVICE BULLETIN 757-53A0103
ALERT  ALERT
S-20
S-21
S-22
S-23
•
S-24
INSPECTION AREA (HOLE LOCATIONS
AND QUANTITIES ARE APPROXIMATE)
O INSULATION BLANKET  S-25
ATTACHMENT HOLE  FRAME
• COORDINATING HOLE  (TYPICAL)
• TOOLING HOLE
2485255
FIGURE 1: OPEN HOLE HIGH FREQUENCY EDDY CURRENT INSPECTIONS BETWEEN STRINGERS S-20
AND S-25 FROM STA 440 TO STA 820 AND FROM STA 1300 TO STA 1701
(SHEET 3 OF 4)
Original Issue: June 22, 2016
Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright © Unpublished  757-53A0103
Work - See page 1 for details.  26 of 41

### Page 27

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of frame inspection areas necessary for this figure.
More DataQtyIdentificationNameTaskStep
(a) (b)20S-20L TO S-25L, STA
440 TO STA 820
FRAME WEBInspect1
(a) (b)6S-20R TO S-25R, STA
440 TO STA 540
FRAME WEBInspect
(a) (b)10S-20R TO S-25R, STA
640 TO STA 820
FRAME WEBInspect
(a) (b)21S-20L TO S-25L, STA
1300 TO STA 1701
FRAME WEBInspect
(a) (b)4S-20R TO S-25R, STA
1300 TO STA 1360
FRAME WEBInspect
(a) (b)13S-20R TO S-25R, STA
1460 TO STA 1701
FRAME WEBInspect
(a) In the inspection area, inspect for any open coordinating holes, tooling holes, and insulation blanket at-
tachment holes. A typical coordinating hole has 0.278 - 0.291 inch diameter. A typical tooling hole has a
0.247 - 0.260 inch diameter. A typical insulation blanket attachment hole has a 0.154 - 0.166 inch diameter
or 0.180 - 0.192 inch diameter.
(b) Do an open hole high frequency eddy current (HFEC) inspection of all open coordinating holes, tooling
holes and insulation blanket attachment holes for any crack in accordance with 757 NDT Manual Part 6,
51-00-16.
FIGURE 1: OPEN HOLE HIGH FREQUENCY EDDY CURRENT INSPECTIONS BETWEEN STRINGERS S-20
AND S-25 FROM STA 440 TO STA 820 AND FROM STA 1300 TO STA 1701
(SHEET 4 OF 4)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 22, 2016
757-53A0103
27 of 41
BOEING SERVICE BULLETIN 757-53A0103
ALERTALERT

### Page 28 (OCR)

BOEING SERVICE BULLETIN 757-53A0103
ALERT  ALERT
This Figure applies only to: Group 2.
STA  STA  STA  STA  STA  STA
440  560  620  740  820  920
- S-13L
- S-17L
• S-20L
- S-25L
- S-28L
- S-28 R
- S-25R
-S-20R
- S-17R
- S-13R
NO. 1 CARGO DOOR
FRAME INSPECTION AREAS
A-A  2484360
FIGURE 2: OPEN HOLE HIGH FREQUENCY EDDY CURRENTINSPECTIONS BETWEEN STRINGERS S-20
AND S-25 FROM STA 440 TO STA 820 AND FROM STA 1300 TO STA 1701
(SHEET 1 OF 4)
Original Issue: June 22, 2016
PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  757-53A0103
Work - See page 1 for details.  28 of 41

### Page 29 (OCR)

BOEING SERVICE BULLETIN 757-53A0103
ALERT  ALERT
PRESSURE
PRESSURE
RELIEF VALVES
CONTROL VALVE
1180  STA  1300  STA  1380  STA  1440  STA  1540  STA  1600  STA  1701  STA
• STA
S-13L -  1720
S-17L -
S-20L -
S-25L -
S-29L
S-29R
S-25R-
S-20R-
S-17R-
S-13R
NO. 2 CARGO  NO. 3 CARGO
DOOR  DOOR
FRAME INSPECTION AREAS
B-B
2485251
FIGURE 2: OPEN HOLE HIGH FREQUENCY EDDY CURRENT INSPECTIONS BETWEEN STRINGERS S-20
AND S-25 FROM STA 440 TO STA 820 AND FROM STA 1300 TO STA 1701
(SHEET 2 OF 4)
Original Issue: June 22, 2016
Export Controlled ECCN: 9E991 - BOEING  757-53A0103
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  29 of 41

### Page 30 (OCR)

BOEING SERVICE BULLETIN 757-53A0103
ALERT  ALERT
S-20
S-21
S-22
S-23
•
S-24
INSPECTION AREA (HOLE LOCATIONS
AND QUANTITIES ARE APPROXIMATE)
O INSULATION BLANKET  S-25
ATTACHMENT HOLE  FRAME
• COORDINATING HOLE  (TYPICAL)
• TOOLING HOLE
2485252
FIGURE 2: OPEN HOLE HIGH FREQUENCY EDDY CURRENT INSPECTIONS BETWEEN STRINGERS S-20
AND S-25 FROM STA 440 TO STA 820 AND FROM STA 1300 TO STA 1701
(SHEET 3 OF 4)
Original Issue: June 22, 2016
Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright © Unpublished  757-53A0103
Work - See page 1 for details.  30 of 41

### Page 31

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of frame inspection areas necessary for this figure.
More DataQtyIdentificationNameTaskStep
(a) (b)20S-20L TO S-25L, STA
440 TO STA 820
FRAME WEBInspect1
(a) (b)6S-20R TO S-25R, STA
440 TO STA 540
FRAME WEBInspect
(a) (b)10S-20R TO S-25R, STA
640 TO STA 820
FRAME WEBInspect
(a) (b)21S-20L TO S-25L, STA
1300 TO STA 1701
FRAME WEBInspect
(a) (b)4S-20R TO S-25R, STA
1300 TO STA 1360
FRAME WEBInspect
(a) (b)4S-20R TO S-25R, STA
1460 TO STA 1520
FRAME WEBInspect
(a) (b)5S-20R TO S-25R, STA
1620 TO STA 1701
FRAME WEBInspect
(a) In the inspection area, inspect for any open coordinating holes, tooling holes, and insulation blanket at-
tachment holes. A typical coordinating hole has 0.278 - 0.291 inch diameter. A typical tooling hole has a
0.247 - 0.260 inch diameter. A typical insulation blanket attachment hole has a 0.154 - 0.166 inch diameter
or 0.180 - 0.192 inch diameter.
(b) Do an open hole high frequency eddy current (HFEC) inspection of all open coordinating holes, tooling
holes and insulation blanket attachment holes for any crack in accordance with 757 NDT Manual Part 6,
51-00-16.
FIGURE 2: OPEN HOLE HIGH FREQUENCY EDDY CURRENT INSPECTIONS BETWEEN STRINGERS S-20
AND S-25 FROM STA 440 TO STA 820 AND FROM STA 1300 TO STA 1701
(SHEET 4 OF 4)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 22, 2016
757-53A0103
31 of 41
BOEING SERVICE BULLETIN 757-53A0103
ALERTALERT

### Page 32 (OCR)

BOEING SERVICE BULLETIN 757-53A0103
ALERT  ALERT
This Figure applies only to: Group 1.
STA  STA  STA  STA  STA  STA
440  560  620  740  820  920
- S-13L
- S-17L
• S-20L
- S-25L
- S-28L
- S-28 R
- S-25R
-S-20R
- S-17R
- S-13R
NO. 1 CARGO DOOR
FRAME MODIFICATION AREAS
A-A  2484730
FIGURE 3: MODIFICATION OF FRAME WEB BETWEEN STRINGERS S-20 AND S-25 FROM STA 440 TO
STA 820 AND FROM STA 1300 TO STA 1701
(SHEET 1 OF 4)
Original Issue: June 22, 2016
PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  757-53A0103
Work - See page 1 for details.  32 of 41

### Page 33 (OCR)

BOEING SERVICE BULLETIN 757-53A0103
ALERT  ALERT
PRESSURE  RELIEF VALVES  PRESSURE  CONTROL VALVE
STA  STA  STA  STA
1180  1300  1360  1701
• STA
S-13L -  1720
S-17L -
S-20L -
S-25L -
S-29L
S-29R
S-25R-
S-20R-
S-17R-
S-13R-
NO. 2 CARGO
DOOR
FRAME MODIFICATION AREAS
B-B
2484361
FIGURE 3: MODIFICATION OF FRAME WEB BETWEEN STRINGERS S-20 AND S-25 FROM STA 440 TO
STA 820 AND FROM STA 1300 TO STA 1701
(SHEET 2 OF 4)
Original Issue: June 22, 2016
Export Controlled ECCN: 9E991 - BOEING  757-53A0103
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  33 of 41

### Page 34 (OCR)

BOEING SERVICE BULLETIN 757-53A0103
ALERT  ALERT
S-20
S-21
S-22
S-23
•
S-24
FRAME WEB (HOLE LOCATIONS AND
QUANTITIES ARE APPROXIMATE)
O INSULATION BLANKET  S-25
ATTACHMENT HOLE  FRAME
• COORDINATING HOLE  (TYPICAL)
• TOOLING HOLE
2484351
FIGURE 3: MODIFICATION OF FRAME WEB BETWEEN STRINGERS S-20 AND S-25 FROM STA 440 TO
STA 820 AND FROM STA 1300 TO STA 1701
(SHEET 3 OF 4)
Original Issue: June 22, 2016
Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright © Unpublished  757-53A0103
Work - See page 1 for details.  34 of 41

### Page 35

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of frame inspection areas necessary for this figure.
More DataQtyIdentificationNameTaskStep
(a) (b)--OPEN HOLESReam1
(c)--OPEN HOLESDeburr2
(d) (e)--RIVETInstall (New)3
(a) A typical coordinating hole has 0.278 - 0.291 inch diameter. A typical tooling hole has a 0.247 - 0.260
inch diameter. A typical insulation blanket attachment hole has a 0.154 - 0.166 inch diameter or 0.180 -
0.192 inch diameter.
(b) Increase the diameter of each open hole to the next nominal fastener size. Refer to 757-200 SRM 51-30-
01 or 757-200PF SRM 51-30-01 as an accepted procedure.
Hole diameter of 0.154 to 0.166 inch increases to 0.225 to 0.231 inch to install 7/32 diameter rivet.
Hole diameter of 0.180 to 0.192 inch increases to 0.253 to 0.259 inch to install 8/32 diameter rivet.
Hole diameter of 0.247 to 0.260 inch increases to 0.316 to 0.322 inch to install 10/32 diameter rivet.
Hole diameter of 0.278 to 0.291 inch increases to 0.348 to 0.358 inch to install 11/32 diameter rivet.
(c) Remove all sharp edges.
(d) Refer to Fastener Table for type of rivet.
(e) Install rivets in all open hole locations. Refer to 757-200 SRM 51-40-02 or 757-200PF SRM 51-40-02 as
an accepted procedure.
Fastener Table
More DataHole DiaQtyIdentificationName
(a)0.225 to 0.231-BACR15FT7AD()RIVET
(a)0.253 to 0.259-BACR15FT8AD()RIVET
(a)0.316 to 0.322-BACR15FT10AD()RIVET
(a)0.348 to 0.358-BACR15FT11AD()RIVET
(a) Multiple gauges are used in frame web construction. Measure the web for fastener grip length. Refer to
757-200 SRM 51-40-02 or 757-200PF SRM 51-40-02 as an accepted procedure.
FIGURE 3: MODIFICATION OF FRAME WEB BETWEEN STRINGERS S-20 AND S-25 FROM STA 440 TO
STA 820 AND FROM STA 1300 TO STA 1701
(SHEET 4 OF 4)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 22, 2016
757-53A0103
35 of 41
BOEING SERVICE BULLETIN 757-53A0103
ALERTALERT

### Page 36 (OCR)

BOEING SERVICE BULLETIN 757-53A0103
ALERT  ALERT
This Figure applies only to: Group 2.
STA  STA  STA  STA  STA  STA
440  560  620  740  820  920
- S-13L
- S-17L
• S-20L
- S-25L
- S-28L
- S-28 R
- S-25R
-S-20R
- S-17R
- S-13R
NO. 1 CARGO DOOR
FRAME MODIFICATION AREAS
A-A  2485268
FIGURE 4: MODIFICATION OF FRAME WEB BETWEEN STRINGERS S-20 AND S-25 FROM STA 440 TO
STA 820 AND FROM STA 1300 TO STA 1701
(SHEET 1 OF 4)
Original Issue: June 22, 2016
PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  757-53A0103
Work - See page 1 for details.  36 of 41

### Page 37 (OCR)

BOEING SERVICE BULLETIN 757-53A0103
ALERT  ALERT
PRESSURE
PRESSURE
RELIEF VALVES
CONTROL VALVE
1180  STA  1300  STA  1380  STA  1440  STA  1540  STA  1600  STA  1701  STA
• STA
S-13L -  1720
S-17L -
S-20L -
S-25L -
S-29L
S-29R
S-25R-
S-20R-
S-17R-
S-13R-
NO. 2 CARGO  NO. 3 CARGO
DOOR  DOOR
FRAME MODIFICATION AREAS
B-B
2485269
FIGURE 4: MODIFICATION OF FRAME WEB BETWEEN STRINGERS S-20 AND S-25 FROM STA 440 TO
STA 820 AND FROM STA 1300 TO STA 1701
(SHEET 2 OF 4)
Original Issue: June 22, 2016
Export Controlled ECCN: 9E991 - BOEING  757-53A0103
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  37 of 41

### Page 38 (OCR)

BOEING SERVICE BULLETIN 757-53A0103
ALERT  ALERT
S-20
S-21
S-22
S-23
•
S-24
FRAME WEB (HOLE LOCATIONS AND
QUANTITIES ARE APPROXIMATE)
O INSULATION BLANKET  S-25
ATTACHMENT HOLE  FRAME
• COORDINATING HOLE  (TYPICAL)
• TOOLING HOLE
2485270
FIGURE 4: MODIFICATION OF FRAME WEB BETWEEN STRINGERS S-20 AND S-25 FROM STA 440 TO
STA 820 AND FROM STA 1300 TO STA 1701
(SHEET 3 OF 4)
Original Issue: June 22, 2016
Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright © Unpublished  757-53A0103
Work - See page 1 for details.  38 of 41

### Page 39

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of frame inspection areas necessary for this figure.
More DataQtyIdentificationNameTaskStep
(a) (b)--OPEN HOLESReam1
(c)--OPEN HOLESDeburr2
(d) (e)--RIVETInstall (New)3
(a) A typical coordinating hole has 0.278 - 0.291 inch diameter. A typical tooling hole has a 0.247 - 0.260
inch diameter. A typical insulation blanket attachment hole has a 0.154 - 0.166 inch diameter or 0.180 -
0.192 inch diameter.
(b) Increase the diameter of each open hole to the next nominal fastener size. Refer to 757-200 SRM 51-30-
01 or 757-200PF SRM 51-30-01 as an accepted procedure.
Hole diameter of 0.154 to 0.166 inch increases to 0.225 to 0.231 inch to install 7/32 diameter rivet.
Hole diameter of 0.180 to 0.192 inch increases to 0.253 to 0.259 inch to install 8/32 diameter rivet.
Hole diameter of 0.247 to 0.260 inch increases to 0.316 to 0.322 inch to install 10/32 diameter rivet.
Hole diameter of 0.278 to 0.291 inch increases to 0.348 to 0.358 inch to install 11/32 diameter rivet.
(c) Remove all sharp edges.
(d) Refer to Fastener Table for type of rivet.
(e) Install rivets in all open hole locations. Refer to 757-200 SRM 51-40-02 or 757-200PF SRM 51-40-02 as
an accepted procedure.
Fastener Table
More DataHole DiaQtyIdentificationName
(a)0.225 to 0.231-BACR15FT7AD()RIVET
(a)0.253 to 0.259-BACR15FT8AD()RIVET
(a)0.316 to 0.322-BACR15FT10AD()RIVET
(a)0.348 to 0.358-BACR15FT11AD()RIVET
(a) Multiple gauges are used in frame web construction. Measure the web for fastener grip length. Refer to
757-200 SRM 51-40-02 or 757-200PF SRM 51-40-02 as an accepted procedure.
FIGURE 4: MODIFICATION OF FRAME WEB BETWEEN STRINGERS S-20 AND S-25 FROM STA 440 TO
STA 820 AND FROM STA 1300 TO STA 1701
(SHEET 4 OF 4)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 22, 2016
757-53A0103
39 of 41
BOEING SERVICE BULLETIN 757-53A0103
ALERTALERT

### Page 40

Logic diagrams are provided as an aid only. Information contained in Paragraph 1.E., Compliance is the primary
source for compliance times. Information contained in Paragraph 3.B., Work Instructions is the primary source
for tasks required for compliance.
1. The table below gives the description for the parts and conditions called out in the logic diagram.
DescriptionTitle
INSPECTION OF THE FRAME WEBS BETWEEN STRINGERS S-20 AND
S-25
PART 2
MODIFICATION OF THE FRAME WEBS BETWEEN STRINGERS S-20 AND
S-25
PART 3
ANY CRACK FOUNDCONDITION 1
NO CRACK FOUNDCONDITION 2
2. The table below gives the description for the flag notes called out in the logic diagram.
DescriptionFlag Note Letter
It is not necessary to do inspections in accordance with this service bulletin
at any coordinating holes, tooling holes, and insulation blanket holes that have
been filled with an aluminum rivet, filled in accordance with 757-200 SRM 53-
00-07 Repair 5 or 757-200PF SRM 53-00-07 Repair 5, or have been used as
part of a Boeing Company approved repair via FAA form 8100-9 or 8110-3.
(a)
Accomplishment of PART 3: MODIFICATION OF THE FRAME WEBS BE-
TWEEN STRINGERS S-20 AND S-25 is terminating action to the repeat in-
spections at modified locations only.
(b)
APPENDIX A:  LOGIC DIAGRAM FOR PARAGRAPH 1.E. COMPLIANCE, TABLE 1: INSPECTION AND
MODIFICATION OF OPEN HOLES ON FRAME WEBS BETWEEN STRINGERS S-20 AND S-25
(SHEET 1 OF 2)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 22, 2016
757-53A0103
40 of 41
BOEING SERVICE BULLETIN 757-53A0103
ALERTALERT

### Page 41 (OCR)

BOEING SERVICE BULLETIN 757-53A0103
ALERT  ALERT
WHICHEVER OCCURS LATER
WITHIN 3,000 FLIGHT
BEFORE 28,000 TOTAL  CYCLES AFTER THE
FLIGHT CYCLES  ORIGINAL ISSUE DATE OF
THIS SERVICE BULLETIN
DO PART 2
(a)
CONDITION 1  CONDITION 2
BEFORE FURTHER  NOT TO EXCEED 12,000
FLIGHT  FLIGHT CYCLES
ACTION 1: CONTACT THE
BOEING COMPANY FOR
REPAIR INSTRUCTIONS  AND DO THE REPAIR  ACTION 1: REPEAT PART 2 AT  ALL OPEN HOLE LOCATIONS
(a)
NOT TO EXCEED 12,000
FLIGHT CYCLES  BEFORE 59,000
TOTAL FLIGHT
CYCLES
ACTION 2: REPEAT PART 2 AT
ALL UNREPAIRED LOCATIONS  ACTION 2: DO PART 3 AT ALL
OPEN HOLE LOCATIONS
(TERMINATING ACTION)
(b)
BEFORE 59,000
TOTAL FLIGHT
CYCLES
ACTION 3: DO PART 3 AT ALL
UNREPAIRED LOCATIONS
(TERMINATING ACTION)
2480891
APPENDIX A: LOGIC DIAGRAM FOR PARAGRAPH 1.E. COMPLIANCE, TABLE 1: INSPECTION AND
MODIFICATION OF OPEN HOLES ON FRAME WEBS BETWEEN STRINGERS S-20 AND S-25
(SHEET 2 OF 2)
Original Issue: June 22, 2016
Export Controlled ECCN: 9E991 - BOEING  757-53A0103
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  41 of 41

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
