# Boeing Alert Requirements Bulletin 757-57A0073 RB: Revision 2

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2021-0685; AD 2022-08-12 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Alert Requirements Bulletin 757-57A0073 RB](https://openairdocs.org/service-documents/boeing/757-57a0073-rb.md)
- Title as filed: 757-57A0073 RB R2 - BOEING
- Pages: 105
- PDF: https://openairdocs.org/files/sha256/19/c9/19c9f832fb170cffac87c5a27446269d7d2f2f4d80b9a2f63c40f9392f252750
- Page: https://openairdocs.org/service-documents/boeing/757-57a0073-rb/file/19c9f832fb17

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Commercial 
Airplanes
757
Requirements Bulletin
ALERT
Number: 757-57A0073 RB
Original Issue: July 14, 2017
Revision 2: March 01, 2021
ATA System: 5720
SUBJECT: WINGS - Outer Wing - Upper Skin, Drag Fittings and Diagonal Brace Fastener and
Shim Inspections
Export of this technology is controlled under the United States Export Administration Regulations (EAR) (15
CFR 300-774). An export license may be required before it is used for development, production or use by foreign
persons from specific countries. The controller of this data has the individual responsibility to abide by all export
laws.
9E991ECCN:
Copyright © 2017 Boeing.
Unpublished Work. All Rights Reserved.
Treatment of this document and its content is governed by contract with Boeing. Rights to use this document
are licensed on a per aircraft basis and such rights may not be transferable. For more information, contact The
Boeing Company.
Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner,
BBJ, DC-8, DC-9, DC-10, KC-10, KC-46, KDC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8, Poseidon and
Boeing liveries are all trademarks owned by The Boeing Company; and no trademark license is granted in
connection with this document unless provided in writing by Boeing.
Original Issue: July 14, 2017
757-57A0073 RBRevision 2: March 01, 2021
1 of 105
4.0

### Page 2

Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 2: March 01, 2021
2 of 105
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT
BLANK PAGE

### Page 3

Table of Contents
Revision Transmittal Sheet ............................................ 5
1 . E F F E C T I V I T Y  ................................................ 7
A. Airplanes ................................................ 7
B . S p a r e s  A f f e c t e d  ........................................... 1 0
2. CONCURRENT REQUIREMENTS .................................... 1 0
3 . C O M P L I A N C E  ............................................... 1 0
4. APPROVAL ................................................ 3 5
5. ACCOMPLISHMENT INSTRUCTIONS .................................. 3 7
A. General Information ......................................... 3 7
B. Work Instructions ........................................... 3 9
FIGURE 1: LEFT WING - DRAG FITTINGS AND WING UPPER SKIN - LOOSE FASTENER INSPECTION
.................................................. 5 4
FIGURE 2: RIGHT WING - DRAG FITTINGS AND WING UPPER SKIN - LOOSE FASTENER INSPECTION
.................................................. 5 6
FIGURE 3: LEFT WING - DRAG FITTINGS AND WING UPPER SKIN - SHIM MIGRATION INSPECTION
.................................................. 5 8
FIGURE 4: RIGHT WING - DRAG FITTINGS AND WING UPPER SKIN - SHIM MIGRATION INSPECTION
.................................................. 6 2
FIGURE 5: LEFT WING - DRAG FITTINGS AND WING UPPER SKIN - FASTENER 1-10 OPEN-HOLE
HFEC INSPECTION ...................................... 6 6
FIGURE 6: RIGHT WING - DRAG FITTINGS AND WING UPPER SKIN - FASTENER 1-10 OPEN-HOLE
HFEC INSPECTION ...................................... 6 8
FIGURE 7: LEFT WING - DRAG FITTINGS AND WING UPPER SKIN - LOOSE FASTENER 11-18
OPEN-HOLE HFEC INSPECTION [Group 1-9] ........................ 7 0
FIGURE 8: RIGHT WING - DRAG FITTINGS AND WING UPPER SKIN - LOOSE FASTENER 11-18
OPEN-HOLE HFEC INSPECTION [Group 1-9] ........................ 7 2
FIGURE 9: LEFT WING- DIAGONAL BRACE AND DIAGONAL BRACE FITTINGS - GENERAL VISUAL
INSPECTION FOR CRACKS ................................. 7 4
FIGURE 10: RIGHT WING- DIAGONAL BRACE AND DIAGONAL BRACE FITTINGS - GENERAL VISUAL
INSPECTION FOR CRACKS ................................. 7 7
FIGURE 11: LEFT WING - WING UPPER SKIN - DETAILED INSPECTION FOR CRACKS ...... 8 0
FIGURE 12: RIGHT WING - WING UPPER SKIN - DETAILED INSPECTION FOR CRACKS ...... 8 2
FIGURE 13: LEFT WING - DRAG FITTINGS - INBOARD SHIM BOLT TORQUE CHECK [Group 1-9] . 84
FIGURE 14: RIGHT WING - DRAG FITTINGS - INBOARD SHIM BOLT TORQUE CHECK [Group 1-9] . 86
FIGURE 15: LEFT WING - DRAG FITTINGS - OUTBOARD SHIM BOLT TORQUE CHECK [Group 1-9] . 88
FIGURE 16: RIGHT WING - DRAG FITTINGS - OUTBOARD SHIM BOLT TORQUE CHECK [Group 1-9]
.................................................. 9 0
FIGURE 17: LEFT WING - DRAG FITTINGS - INBOARD SHIM BOLT TORQUE CHECK [Group 10-11] . 92
FIGURE 18: RIGHT WING - DRAG FITTINGS - INBOARD SHIM BOLT TORQUE CHECK [Group 10-11]
.................................................. 9 4
FIGURE 19: LEFT WING - DRAG FITTINGS - OUTBOARD SHIM BOLT TORQUE CHECK [Group 10-11]
.................................................. 9 6
FIGURE 20: RIGHT WING - DRAG FITTINGS - OUTBOARD SHIM BOLT TORQUE CHECK [Group 10-11]
.................................................. 9 8
FIGURE 21: LEFT WING - DRAG FITTINGS AND WING UPPER SKIN - FASTENER 11-18 OPEN-HOLE
HFEC INSPECTION ..................................... 1 0 0
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 2: March 01, 2021
3 of 105
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 4

FIGURE 22: RIGHT WING - DRAG FITTINGS AND WING UPPER SKIN - FASTENER 11-18 OPEN-HOLE
HFEC INSPECTION ..................................... 1 0 3
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 2: March 01, 2021
4 of 105
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 5

Commercial 
Airplanes
757
Requirements Bulletin
ALERT
Revision Transmittal SheetNumber: 757-57A0073 RBOriginal Issue: July 14, 2017
Revision 2: March 01, 2021
ATA System: 5720
SUBJECT: WINGS - Outer Wing - Upper Skin, Drag Fittings and Diagonal Brace Fastener and
Shim Inspections
This revision includes all pages of the requirements bulletin.
COMPLIANCE INFORMATION RELATED TO THIS REVISION
Federal Aviation Administration (FAA) Airworthiness Directive AD 2020-21-17 is related to the requirements
bulletin. The effective date of AD 2020-21-17 is January 14, 2021.
Federal Aviation Administration (FAA) Notice of Proposed Rule Making NPRM 2019-NM-161-AD, is related to
this service bulletin.
The Federal Aviation Administration (FAA) will possibly release an additional Airworthiness Directive related to
the Requirements Bulletin 757-57A0073 RB Revision 2. The Airworthiness Directive will make the compliance
tasks and times given in Requirements Bulletin 757-57A0073 RB Revision 2 mandatory.
Effects of this Revision on airplanes on which the Revision 1 Issue of this Service Bulletin was previously done:
None.
Effects of this Revision on airplanes on which the Original Issue of this Service Bulletin was previously done:
ActionConditionGroup
Do an open-hole High Frequency
Eddy Current (HFEC) inspection at
fastener locations 1-10 for any crack
and do applicable on-condition ac-
tions at the revised times specified
in Compliance.
Airplanes on which the Original Is-
sue of this Service Bulletin was pre-
viously done.
3-4
REASON FOR REVISION
This revision is sent to revise the compliance time for Open-Hole High Frequency Eddy Current inspections of
holes 1-10 for airplanes in Groups 3 and 4.
These sections were changed:
- In Compliance, updated Airworthiness Directive (AD) related information to be Revision 2.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 2: March 01, 2021
5 of 105

### Page 6

- In Compliance, added Notice of Proposed Rule Making (NPRM) related information.
- In Compliance, updated compliance time in Table 1 through Table 9.
REVISION HISTORY
Service BulletinService BulletinRequirement BulletinRequirement Bulletin
757-57A0073757-57A0073757-57A0073 RB757-57A0073 RB
Issue DateIssue Date
July 14, 2017Original Issue:July 14, 2017Original Issue:
August 01, 2019Revision 1:August 01, 2019Revision 1:
March 01, 2021Revision 2:March 01, 2021Revision 2:
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 2: March 01, 2021
6 of 105
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 7

Commercial 
Airplanes
757
Requirements Bulletin
ALERT
Number: 757-57A0073 RB
Original Issue: July 14, 2017
Revision 2: March 01, 2021
ATA System: 5720
SUBJECT: WINGS - Outer Wing - Upper Skin, Drag Fittings and Diagonal Brace Fastener and
Shim Inspections
THIS DOCUMENT IS SENT TO THE OPERATORS OF RECORD OF THE AIRPLANES SHOWN IN
PARAGRAPH 1.A., EFFECTIVITY. IF AN AIRPLANE HAS BEEN LEASED OR SOLD, SEND THIS DOCUMENT
TO THE NEW OPERATOR. IF APPLICABLE SPARES HAVE BEEN SOLD, SEND THIS DOCUMENT TO THE
NEW OWNER. THIS IS AN ENHANCED REQUIRED FOR COMPLIANCE DOCUMENT. THE BOEING
PROCESSES USED TO CREATE THE SERVICE BULLETIN (SB) AND THE REQUIREMENTS BULLETIN
(RB) ENSURE THAT THE INFORMATION BETWEEN "RC START" AND "RC END" IN THE SB ARE IDENTICAL
TO THE INFORMATION IN THE SAME SECTIONS (COMPLIANCE, WORK INSTRUCTIONS…) OF THE RB
WHICH THE SB REFERS TO AS THE RELATED DOCUMENT.
1. Effectivity
A. Airplanes
This bulletin is applicable to 757-200, 757-200CB, 757-200PF, 757-300 Airplane(s), line number(s)
1-1050 in 11 Group(s). Where the effectivity is presented with hyphens between line numbers, the
airplane applicability means "through" and "inclusive", e.g. line numbers 1-9 means line numbers
1 through 9 inclusive.
DESCRIPTIONCONFIGURATIONGROUP
757-200/-200CB/-200PF Airplanes, Line Numbers 1-735 with
Rolls-Royce engines and with cold work
-1
Airplanes that have not accomplished SB 757-54-0035.1
Airplanes that have accomplished SB 757-54-0035.2
757-200/-200PF Airplanes, Line Numbers 736-802 with Rolls-Royce
engines and with cold work.
-2
757-200 Airplanes, Line Numbers 803-1009 with Rolls-Royce engines
and without cold work
-3
757-200 Airplanes, Line Numbers 1010-1050 with Rolls-Royce
engines and without cold work
-4
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 2: March 01, 2021
7 of 105

### Page 8

DESCRIPTIONCONFIGURATIONGROUP
757-200/-200PF Airplanes, Line Numbers 1-735 with Pratt and
Whitney engines and with cold work
-5
Airplanes that have not accomplished SB 757-54-0034.1
Airplanes that have accomplished SB 757-54-0034.2
757-200 Airplanes, Line Numbers 736-802 with Pratt and Whitney
engines and with cold work
-6
757-200 Airplanes, Line Numbers 803-1009 with Pratt and Whitney
engines and without cold work
-7
757-200 Airplanes, Line Numbers 1010-1050 with Pratt and Whitney
engines and without cold work
-8
757-300 Airplanes, Line Numbers 804-855 with Rolls-Royce engines
and shear-head bolts in the drag fitting and without cold work
-9
757-300 Airplanes, Line Numbers 906-1043 with Rolls-Royce engines
and tension-head bolts in the drag fitting and without cold work
-10
757-300 Airplanes, Line Numbers 906-1043 with Pratt and Whitney
engines and tension-head bolts in the drag fitting and without cold
work
-11
Airplane Models:
757-200, 757-200CB, 757-200PF, 757-300
GroupVariable Number
5NA001
1NA002 - NA028
1NA191 - NA199
1NA201 - NA239
1NA301 - NA305
1NA341 - NA352
1NA391 - NA399
1NA401 - NA408
1NA441 - NA447
5NA501 - NA586
GroupVariable Number
5NB001 - NB004
1NB021 - NB023
1NB036 - NB041
1NB051 - NB053
1NB061 - NB073
1NB079
1NB131 - NB148
1NB161 - NB162
5NB166 - NB168
1NB201 - NB204
GroupVariable Number
1NB221 - NB225
2NB226 - NB228
2NB230
1NB236
1NB239
1NB261 - NB267
1NB291 - NB299
1NB301 - NB302
1NB311 - NB312
1NB321 - NB331
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 2: March 01, 2021
8 of 105
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 9

GroupVariable Number
1NB421 - NB438
1NB446
1NB451 - NB454
1NB501 - NB523
1NB561
2NB571
2NB581 - NB583
5NC001 - NC033
5NC041 - NC042
5NC051 - NC052
5NC056 - NC057
1NC058 - NC061
2NC062
5NC066 - NC076
6NC077 - NC084
6NC091 - NC094
5NC151
6NC161
5NC901 - NC935
1NC936 - NC950
5NC951
1NC971 - NC974
1ND001 - ND007
1ND011 - ND059
1ND111 - ND113
1ND161 - ND199
1ND201 - ND203
1ND221 - ND225
1ND241 - ND248
1ND301 - ND317
2ND318 - ND322
2ND401
1ND891
GroupVariable Number
1ND895
5NE001 - NE007
6NE008
5NE011 - NE088
5NE091 - NE094
5NE141 - NE150
5NE161 - NE177
5NE201 - NE204
5NE301 - NE302
5NE311 - NE325
4NJ001 - NJ004
4NJ031 - NJ032
8NJ551 - NJ555
10NL001 - NL002
10NL006 - NL017
10NL101 - NL109
10NL141
11NL601 - NL616
3NN001 - NN002
3NN051 - NN052
6NP901 - NP902
7NP903 - NP904
1NS601 - NS610
2NS611 - NS616
2NT001 - NT004
3NT005 - NT009
3NT201 - NT202
2NT231 - NT232
3NT233 - NT234
3NT237 - NT240
3NT242
3NT245 - NT248
2NT281
GroupVariable Number
3NT282 - NT289
6NT341 - NT344
7NT345 - NT346
8NT347
6NT351
7NT352 - NT360
7NT371 - NT373
7NT375 - NT379
2NT381
3NT382 - NT385
4NT386
2NT401 - NT403
3NT404 - NT409
3NT411 - NT412
3NT426 - NT427
3NT431 - NT432
3NT436 - NT438
7NT441 - NT442
3NT446
6NT701
7NT702 - NT730
3NT731 - NT750
2NT751 - NT758
3NT759 - NT769
6NT791 - NT794
7NT795 - NT796
2NT861
3NT862
7NT881 - NT885
3NT901 - NT916
3NT971 - NT984
4NT985
7NU031 - NU035
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 2: March 01, 2021
9 of 105
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 10

GroupVariable Number
8NU036 - NU038
9NU701
GroupVariable Number
10NU702 - NU705
9NU721 - NU726
GroupVariable Number
10NU727 - NU728
10NU731 - NU732
B. Spares Affected
None.
2. CONCURRENT REQUIREMENTS
None.
3. COMPLIANCE
Federal Aviation Administration (FAA) Airworthiness Directive AD 2020-21-17 is related to Requirements
Bulletin 757-57A0073 RB. The effective date of AD 2020-21-17 is January 14, 2021.
Federal Aviation Administration (FAA) Notice of Proposed Rule Making NPRM 2019-NM-161-AD, is related
to this service bulletin.
The Federal Aviation Administration (FAA) will possibly release an additional Airworthiness Directive related
to Requirements Bulletin 757-57A0073 R02 RB. The Airworthiness Directive will make the compliance tasks
and times given in Requirements Bulletin 757-57A0073 R02 RB mandatory.
Accomplish the required action(s), based on the applicable condition(s) in Table(s) 1 through 16, in
accordance with the Accomplishment Instructions.
When more than one OPTION is given for a CONDITION, do only one of the OPTION numbers. When
more than one ACTION is given for a CONDITION or an OPTION, do all of the ACTION numbers for that
CONDITION or OPTION.
Each Group has three tables that give the compliance for the affected airplanes. The following table shows
which compliance tables apply to each Group.
Applicable TablesGroups
Table 7, Table 9, Table 10Group 1, Configuration 1:
Table 1, Table 3, Table 11Group 1, Configuration 2:
Table 1, Table 3, Table 12Group 2:
Table 1, Table 4, Table 12Group 3-4:
Table 8, Table 9, Table 13Group 5, Configuration 1:
Table 1, Table 5, Table 14Group 5, Configuration 2:
Table 1, Table 5, Table 15Group 6:
Table 1, Table 6, Table 15Group 7-8:
Table 1, Table 6, Table 16Group 9:
Table 2, Table 6, Table 16Group 10:
Table 2, Table 6, Table 15Group 11:
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 2: March 01, 2021
10 of 105
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 11

Group 1, Configuration 2; Group 2-4; Group 5, Configuration 2; Group 6-9:
Table 1: Inspection for loose fasteners, skin cracking and shim migration at the upper link drag fittings
and for cracks in the diagonal brace and diagonal brace fittings
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Within 2,100
flight cycles af-
ter the Revision
1 date of Re-
quirements Bul-
letin 757-
57A0073 RB
Before 6,000 to-
tal flight cycles
ACTION 1: Do a general
visual inspection of the
diagonal brace and diago-
nal brace fittings for any
crack.
All Airplanes
-Within 3,000
flight cycles af-
ter the Original
Issue date of
Requirements
Bulletin 757-
57A0073 RB
ACTION 2: Do inspec-
tions for loose fasteners,
skin cracks and shim mi-
grations.
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair.
CONDITION 1: ANY
CRACK FOUND IN DIAG-
ONAL BRACE OR DIAGO-
NAL BRACE FITTINGS (a)
2,100 flight cycles-Repeat general visual in-
spection of the diagonal
brace and diagonal brace
fittings for any crack.
CONDITION 2: NO
CRACK FOUND IN DIAG-
ONAL BRACE OR DIAGO-
NAL BRACE FITTINGS (a)
-Before further flightCONDITION 3 (ACTION
1): Install the Upper Link
and Upper Link Pins if re-
moved.
CONDITION 3: NO SHIM
MIGRATION, NO SKIN
CRACK AND NO LOOSE
FASTENER.
3,000 flight cycles-CONDITION 3 (ACTION
2): Repeat inspections for
loose fasteners, skin
cracks and shim migra-
tions.
-Before further flightDo open-hole HFEC in-
spection of fastener holes
1-10 for cracks.
CONDITION 4: ANY
LOOSE FASTENER
FOUND ON FASTENERS
1-10 (a)
-Before further flightDo open-hole HFEC in-
spection on the loose bolt
hole(s) for cracks.
CONDITION 5: ANY
LOOSE FASTENER
FOUND ON FASTENERS
11-18 (a)
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 2: March 01, 2021
11 of 105
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 12

Group 1, Configuration 2; Group 2-4; Group 5, Configuration 2; Group 6-9:
Table 1: Inspection for loose fasteners, skin cracking and shim migration at the upper link drag fittings
and for cracks in the diagonal brace and diagonal brace fittings
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair.
CONDITION 6: MAJOR
SHIM MIGRATION
FOUND (a)
-Before further flightOPTION 1: Contact The
Boeing Company for re-
pair instructions and do
the repair.
CONDITION 7: ANY
CRACK FOUND IN THE
DRAG FITTINGS (a)
-Before further flightOPTION 2 (ACTION 1):
Replace any cracked
drag fitting with a new
part.
-Before further flightOPTION 2 (ACTION 2):
Install the Upper Link and
Upper Link Pins if re-
moved.
3,000 flight cycles-OPTION 2 (ACTION 3):
Repeat inspections for
loose fasteners, skin
cracks and shim migra-
tions.
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair.
CONDITION 8: ANY
CRACK FOUND IN SKIN
(a)
-Before further flightCONDITION 9 (ACTION
1): Install new or service-
able bolts, new or kept
washers, and new nuts
for fastener holes where
fasteners were removed.
CONDITION 9: NO
CRACK FOUND IN SKIN
AND DRAG FITTINGS
DURING OPEN-HOLE
HFEC INSPECTION (a)
-Before further flightCONDITION 9 (ACTION
2): Install the Upper Link
and Upper Link Pins if re-
moved.
3,000 flight cycles-CONDITION 9 (ACTION
3): Repeat inspections for
loose fasteners, skin
cracks and shim migra-
tions.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 2: March 01, 2021
12 of 105
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 13

Group 1, Configuration 2; Group 2-4; Group 5, Configuration 2; Group 6-9:
Table 1: Inspection for loose fasteners, skin cracking and shim migration at the upper link drag fittings
and for cracks in the diagonal brace and diagonal brace fittings
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flightDo a torque check of fas-
teners on the affected
shim(s).
CONDITION 10: MINOR
SHIM MIGRATION
FOUND IN SKIN PANEL
SHIM (a)
-Before further flightCONDITION 10.1 (AC-
TION 1): Trim affected
shim to the edge of the
fitting. Apply chemical
conversion coating on the
shim and fillet seal the
edge of the drag fitting.
CONDITION 10.1: ALL
BOLTS PASSED THE
TORQUE CHECK
-Before further flightCONDITION 10.1 (AC-
TION 2): Install the Upper
Link and Upper Link Pins
if removed.
3,000 flight cycles-CONDITION 10.1 (AC-
TION 3): Repeat inspec-
tions for loose fasteners,
skin cracks and shim mi-
grations.
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair.
CONDITION 10.2: ANY
BOLT FAILED THE
TORQUE CHECK
-Before further flightCONDITION 11 (ACTION
1): Trim affected shim to
the edge of the fitting.
Apply chemical conver-
sion coating on the shim
and fillet seal the edge of
the drag fitting.
CONDITION 11: MINOR
SHIM MIGRATION
FOUND IN SPAR SHIM (a)
-Before further flightCONDITION 11 (ACTION
2): Install the Upper Link
and Upper Link Pins if re-
moved.
3,000 flight cycles-CONDITION 11 (ACTION
3): Repeat inspections for
loose fasteners, skin
cracks and shim migra-
tions.
(a) More than one CONDITION can be applicable on each airplane.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 2: March 01, 2021
13 of 105
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 14

Group 10-11:
Table 2: Inspection for loose fasteners, skin cracking and shim migration at the upper link drag fittings
and for cracks in the diagonal brace and diagonal brace fittings
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Within 2,100
flight cycles af-
ter the Revision
1 date of Re-
quirements Bul-
letin 757-
57A0073 RB
Before 6,000 to-
tal flight cycles
ACTION 1: Do a general
visual inspection of the
diagonal brace and diago-
nal brace fittings for any
crack.
All airplanes
-Within 3,000
flight cycles af-
ter the Original
Issue date of
Requirements
Bulletin 757-
57A0073 RB
ACTION 2: Do inspec-
tions for loose fasteners,
skin cracks and shim mi-
grations.
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair.
CONDITION 1: ANY
CRACK FOUND IN DIAG-
ONAL BRACE OR DIAGO-
NAL BRACE FITTINGS (a)
2,100 flight cycles-Repeat general visual in-
spection of the diagonal
brace and diagonal brace
fittings for any crack.
CONDITION 2: NO
CRACK FOUND IN DIAG-
ONAL BRACE OR DIAGO-
NAL BRACE FITTINGS (a)
-Before further flightCONDITION 3 (ACTION
1): Install the Upper Link
and Upper Link Pins if re-
moved.
CONDITION 3: NO SHIM
MIGRATION, NO SKIN
CRACK AND NO LOOSE
FASTENER.
3,000 flight cycles-CONDITION 3 (ACTION
2): Repeat inspections for
loose fasteners, skin
cracks and shim migra-
tions.
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair.
CONDITION 6: MAJOR
SHIM MIGRATION
FOUND (a)
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 2: March 01, 2021
14 of 105
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 15

Group 10-11:
Table 2: Inspection for loose fasteners, skin cracking and shim migration at the upper link drag fittings
and for cracks in the diagonal brace and diagonal brace fittings
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flightOPTION 1: Contact The
Boeing Company for re-
pair instructions and do
the repair.
CONDITION 7: ANY
CRACK FOUND IN DRAG
FITTINGS (a)
-Before further flightOPTION 2 (ACTION 1):
Replace any cracked
drag fitting with a new
part.
-Before further flightOPTION 2 (ACTION 2):
Install the Upper Link and
Upper Link Pins if re-
moved.
3,000 flight cycles-OPTION 2 (ACTION 3):
Repeat inspections for
loose fasteners, skin
cracks and shim migra-
tions.
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair.
CONDITION 8: ANY
CRACK FOUND IN SKIN
(a)
-Before further flightDo a torque check of fas-
teners on the affected
shim(s).
CONDITION 10: MINOR
SHIM MIGRATION
FOUND IN SKIN PANEL
SHIM (a)
-Before further flightCONDITION 10.1 (AC-
TION 1): Trim affected
shim to the edge of the
fitting. Apply chemical
conversion coating on the
shim and fillet seal the
edge of the drag fitting.
CONDITION 10.1: ALL
BOLTS PASSED THE
TORQUE CHECK
-Before further flightCONDITION 10.1 (AC-
TION 2): Install the Upper
Link and Upper Link Pins
if removed.
3,000 flight cycles-CONDITION 10.1 (AC-
TION 3): Repeat inspec-
tions for loose fasteners,
skin cracks and shim mi-
grations.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 2: March 01, 2021
15 of 105
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 16

Group 10-11:
Table 2: Inspection for loose fasteners, skin cracking and shim migration at the upper link drag fittings
and for cracks in the diagonal brace and diagonal brace fittings
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair.
CONDITION 10.2: ANY
BOLT FAILED THE
TORQUE CHECK
-Before further flightCONDITION 11 (ACTION
1): Trim affected shim to
the edge of the fitting.
Apply chemical conver-
sion coating on the shim
and fillet seal the edge of
the drag fitting.
CONDITION 11: MINOR
SHIM MIGRATION
FOUND IN SPAR SHIM (a)
-Before further flightCONDITION 11 (ACTION
2): Install the Upper Link
and Upper Link Pins if re-
moved.
3,000 flight cycles-CONDITION 11 (ACTION
3): Repeat inspections for
loose fasteners, skin
cracks and shim migra-
tions.
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair.
CONDITION 12: ANY
LOOSE FASTENER
FOUND (a)
(a) More than one CONDITION can be applicable on each airplane.
Group 1, Configuration 2; Group 2:
Table 3: Inspect for cracks in the wing skin and drag fittings at the upper link drag fittings (Fastener
Locations 1-10)
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Within 3,000
flight cycles af-
ter the Original
Issue date of
Requirements
Bulletin 757-
57A0073 RB
Before 23,000
total flight cycles
Do open-hole HFEC in-
spection of fastener holes
1-10 for cracks. (a)(b)
All airplanes
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 2: March 01, 2021
16 of 105
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 17

Group 1, Configuration 2; Group 2:
Table 3: Inspect for cracks in the wing skin and drag fittings at the upper link drag fittings (Fastener
Locations 1-10)
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flightOPTION 1: Contact The
Boeing Company for re-
pair instructions and do
the repair.
CONDITION 7: ANY
CRACK FOUND IN DRAG
FITTINGS (c)
-Before further flightOPTION 2 (ACTION 1):
Replace any cracked
drag fitting with a new
part.
-Before further flightOPTION 2 (ACTION 2):
Install the Upper Link and
Upper Link Pins if re-
moved.
12,000 flight cycles-OPTION 2 (ACTION 3):
Repeat open-hole HFEC
inspection of fastener
holes 1-10 for cracks.
(a)(b)
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair.
CONDITION 8: ANY
CRACK FOUND IN SKIN
(c)
-Before further flightCONDITION 9 (ACTION
1): Install new or service-
able bolts, new or kept
washers, and new nuts.
CONDITION 9: NO
CRACK FOUND IN SKIN
AND DRAG FITTINGS
DURING OPEN-HOLE
HFEC INSPECTION -Before further flightCONDITION 9 (ACTION
2): Install the Upper Link
and Upper Link Pins if re-
moved.
12,000 flight cycles-CONDITION 9 (ACTION
3): Repeat open-hole
HFEC inspection of fas-
tener holes 1-10. (a)(b)
(a) Accomplishment of an open-hole HFEC inspection of fastener holes 1-10 as a result of CONDITION 4
meets the requirements of this action.
(b) As of the Revision 1 date of 757-57A0073 RB, when this action occurs at the same time as a loose fas-
tener inspection from Table 1, the loose fastener inspection in Table 1 must be done first.
(c) More than one CONDITION can be applicable on each airplane.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 2: March 01, 2021
17 of 105
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 18

Group 3-4:
Table 4: Inspect for cracks in the wing skin and drag fittings at the upper link drag fittings (Fastener
Locations 1-10)
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Within 3,000
flight cycles af-
ter the Revision
1 date of Re-
quirements Bul-
letin 757-
57A0073 RB
Before 6,000 to-
tal flight cycles
Do open-hole HFEC in-
spection of fastener holes
1-10 for cracks. (a)(b)
Airplanes on which the in-
spections specified in Re-
quirements Bulletin 757-
5A0073 RB Revision 1
have been done as of the
Revision 2 date of Require-
ments Bulletin 757-
57A0073 RB
-Within 2,300
flight cycles af-
ter the Revision
2 date of Re-
quirements Bul-
letin 757-
57A0073 RB
Before 6,000 to-
tal flight cycles
Do open-hole HFEC in-
spection of fastener holes
1-10 for cracks.(a)(b)
Airplanes on which the in-
spections specified in Re-
quirements Bulletin 757-
5A0073 RB Revision 1
have not been done as of
the Revision 2 date of Re-
quirements Bulletin 757-
57A0073 RB
-Before further flightOPTION 1: Contact The
Boeing Company for re-
pair instructions and do
the repair.
CONDITION 7: ANY
CRACK FOUND IN DRAG
FITTINGS (c)
-Before further flightOPTION 2 (ACTION 1):
Replace any cracked
drag fitting with a new
part.
-Before further flightOPTION 2 (ACTION 2):
Install the Upper Link and
Upper Link Pins if re-
moved.
12,000 flight cycles-OPTION 2 (ACTION 3):
Repeat open-hole HFEC
inspection of fastener
holes 1-10. (a)(b)
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair.
CONDITION 8: ANY
CRACK FOUND IN SKIN
(c)
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 2: March 01, 2021
18 of 105
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 19

Group 3-4:
Table 4: Inspect for cracks in the wing skin and drag fittings at the upper link drag fittings (Fastener
Locations 1-10)
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flightCONDITION 9 (ACTION
1): Install new or service-
able bolts, new or kept
washers, and new nuts.
CONDITION 9: NO
CRACK FOUND IN SKIN
AND DRAG FITTINGS
DURING OPEN-HOLE
HFEC INSPECTION -Before further flightCONDITION 9 (ACTION
2): Install the Upper Link
and Upper Link Pins if re-
moved.
12,000 flight cycles-CONDITION 9 (ACTION
3): Repeat open-hole
HFEC inspection of fas-
tener holes 1-10. (a)(b)
(a) Accomplishment of an open-hole HFEC inspection of fastener holes 1-10 as a result of CONDITION 4
meets the requirements of this action.
(b) As of the Revision 1 date of 757-57A0073 RB, when this action occurs at the same time as a loose fas-
tener inspection from Table 1, the loose fastener inspection in Table 1 must be done first.
(c) More than one CONDITION can be applicable on each airplane.
Group 5, Configuration 2; Group 6:
Table 5: Inspect for cracks in the wing skin and drag fittings at the upper link drag fittings (Fastener
Locations 1-10)
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Within 3,000
flight cycles af-
ter the Original
Issue date of
Requirements
Bulletin 757-
57A0073 RB
Before 23,000
total flight cycles
Do open-hole HFEC in-
spection of fastener holes
1-10 for cracks. (a)(b)
All airplanes
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 2: March 01, 2021
19 of 105
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 20

Group 5, Configuration 2; Group 6:
Table 5: Inspect for cracks in the wing skin and drag fittings at the upper link drag fittings (Fastener
Locations 1-10)
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flightOPTION 1: Contact The
Boeing Company for re-
pair instructions and do
the repair.
CONDITION 7: ANY
CRACK FOUND IN DRAG
FITTINGS (c)
-Before further flightOPTION 2 (ACTION 1):
Replace any cracked
drag fitting with a new
part.
-Before further flightOPTION 2 (ACTION 2):
Install the Upper Link and
Upper Link Pins if re-
moved.
6,000 flight cycles-OPTION 2 (ACTION 3):
Repeat open-hole HFEC
inspection of fastener
holes 1-10. (a)(b)
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair.
CONDITION 8: ANY
CRACK FOUND IN SKIN
(c)
-Before further flightCONDITION 9 (ACTION
1): Install new or service-
able bolts, new or kept
washers, and new nuts.
CONDITION 9: NO
CRACK FOUND IN SKIN
AND DRAG FITTINGS
DURING OPEN-HOLE
HFEC INSPECTION -Before further flightCONDITION 9 (ACTION
2): Install the Upper Link
and Upper Link Pins if re-
moved.
6,000 flight cycles-CONDITION 9 (ACTION
3): Repeat open-hole
HFEC inspection of fas-
tener holes 1-10. (a)(b)
(a) Accomplishment of an open-hole HFEC inspection of fastener holes 1-10 as a result of CONDITION 4
meets the requirements of this action.
(b) As of the Revision 1 date of 757-57A0073 RB, when this action occurs at the same time as a loose fas-
tener inspection from Table 1, the loose fastener inspection in Table 1 must be done first.
(c) More than one CONDITION can be applicable on each airplane.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 2: March 01, 2021
20 of 105
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 21

Group 7-11:
Table 6: Inspect for cracks in the wing skin and drag fittings at the upper link drag fittings (Fastener
Locations 1-10)
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Within 3,000
flight cycles af-
ter the Original
Issue date of
Requirements
Bulletin 757-
57A0073 RB
Before 6,000 to-
tal flight cycles
Do open-hole HFEC in-
spection of fastener holes
1-10 for cracks. (a)(b)
All airplanes
-Before further flightOPTION 1: Contact The
Boeing Company for re-
pair instructions and do
the repair.
CONDITION 7: ANY
CRACK FOUND IN DRAG
FITTINGS (c)
-Before further flightOPTION 2 (ACTION 1):
Replace any cracked
drag fitting with a new
part.
-Before further flightOPTION 2 (ACTION 2):
Install the Upper Link and
Upper Link Pins if re-
moved.
6,000 flight cycles-OPTION 2 (ACTION 3):
Repeat open-hole HFEC
inspection of fastener
holes 1-10. (a)(b)
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair.
CONDITION 8: ANY
CRACK FOUND IN SKIN
(c)
-Before further flightCONDITION 9 (ACTION
1): Install new or service-
able bolts, new or kept
washers, and new nuts.
CONDITION 9: NO
CRACK FOUND IN SKIN
AND DRAG FITTINGS
DURING OPEN-HOLE
HFEC INSPECTION -Before further flightCONDITION 9 (ACTION
2): Install the Upper Link
and Upper Link Pins if re-
moved.
6,000 flight cycles-CONDITION 9 (ACTION
3): Repeat open-hole
HFEC inspection of fas-
tener holes 1-10. (a)(b)
(a) Accomplishment of an open-hole HFEC inspection of fastener holes 1-10 as a result of CONDITION 4
meets the requirements of this action.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 2: March 01, 2021
21 of 105
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 22

Group 7-11:
Table 6: Inspect for cracks in the wing skin and drag fittings at the upper link drag fittings (Fastener
Locations 1-10)
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
(b) As of the Revision 1 date of 757-57A0073 RB, when this action occurs at the same time as a loose fas-
tener inspection from Table 1 or Table 2, the loose fastener inspection in Table 1 or Table 2 must be
done first.
(c) More than one CONDITION can be applicable on each airplane.
Group 1, Configuration 1:
Table 7: Inspect for cracks in the wing skin and drag fittings at the upper link drag fittings (Fastener
Locations 1-10)
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Within 3,000
flight cycles af-
ter the Original
Issue date of
Requirements
Bulletin 757-
57A0073 RB
Before 8,400 to-
tal flight cycles
Do open-hole HFEC in-
spection of fastener holes
1-10 for cracks. (a)(b)
All airplanes
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair.
CONDITION 7: ANY
CRACK FOUND IN DRAG
FITTINGS (c)
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair.
CONDITION 8: ANY
CRACK FOUND IN SKIN
(c)
-Before further flightCONDITION 9 (ACTION
1): Install new or service-
able bolts, new or kept
washers, and new nuts.
CONDITION 9: NO
CRACK FOUND IN SKIN
AND DRAG FITTINGS
DURING OPEN-HOLE
HFEC INSPECTION -Before further flightCONDITION 9 (ACTION
2): Install the Upper Link
and Upper Link Pins if re-
moved.
8,400 flight cycles-CONDITION 9 (ACTION
3): Repeat open-hole
HFEC inspection of fas-
tener holes 1-10. (a)(b)
(a) Accomplishment of an open-hole HFEC inspection of fastener holes 1-10 as a result of CONDITION 4
meets the requirements of this action.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 2: March 01, 2021
22 of 105
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 23

Group 1, Configuration 1:
Table 7: Inspect for cracks in the wing skin and drag fittings at the upper link drag fittings (Fastener
Locations 1-10)
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
(b) As of the Revision 1 date of 757-57A0073 RB, when this action occurs at the same time as a loose fas-
tener inspection from Table 9, the loose fastener inspection in Table 9 must be done first.
(c) More than one CONDITION can be applicable on each airplane.
Group 5, Configuration 1:
Table 8: Inspect for cracks in the wing skin and drag fittings at the upper link drag fittings (Fastener
Locations 1-10)
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Within 3,000
flight cycles af-
ter the Original
Issue date of
Requirements
Bulletin 757-
57A0073 RB
Before 5,500 to-
tal flight cycles
Do open-hole HFEC in-
spection of fastener holes
1-10 for cracks. (a)(b)
All airplanes
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair.
CONDITION 7: ANY
CRACK FOUND IN DRAG
FITTINGS (c)
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair.
CONDITION 8: ANY
CRACK FOUND IN SKIN
(c)
-Before further flightCONDITION 9 (ACTION
1): Install new or service-
able bolts, new or kept
washers, and new nuts.
CONDITION 9: NO
CRACK FOUND IN SKIN
AND DRAG FITTINGS
DURING OPEN-HOLE
HFEC INSPECTION -Before further flightCONDITION 9 (ACTION
2): Install the Upper Link
and Upper Link Pins if re-
moved.
5,500 flight cycles-CONDITION 9 (ACTION
3): Repeat open-hole
HFEC inspection of fas-
tener holes 1-10. (a)(b)
(a) Accomplishment of an open-hole HFEC inspection of fastener holes 1-10 as a result of CONDITION 4
meets the requirements of this action.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 2: March 01, 2021
23 of 105
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 24

Group 5, Configuration 1:
Table 8: Inspect for cracks in the wing skin and drag fittings at the upper link drag fittings (Fastener
Locations 1-10)
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
(b) As of the Revision 1 date of 757-57A0073 RB, when this action occurs at the same time as a loose fas-
tener inspection from Table 9, the loose fastener inspection in Table 9 must be done first.
(c) More than one CONDITION can be applicable on each airplane.
Group 1, 5, Configuration 1:
Table 9: Inspection for loose fasteners, skin cracking and shim migration at the upper link drag fittings
and for cracks in the diagonal brace and diagonal brace fittings
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Within 2,100
flight cycles af-
ter the Revision
1 date of Re-
quirements Bul-
letin 757-
57A0073 RB
Before 6,000 to-
tal flight cycles
ACTION 1: Do a general
visual inspection of the
diagonal brace and diago-
nal brace fittings for any
crack.
All Airplanes
-Within 3,000
flight cycles af-
ter the Original
Issue date of
Requirements
Bulletin 757-
57A0073 RB
ACTION 2: Do inspec-
tions for loose fasteners,
skin cracks and shim mi-
grations.
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair.
CONDITION 1: ANY
CRACK FOUND IN DIAG-
ONAL BRACE OR DIAGO-
NAL BRACE FITTINGS (a)
2,100 flight cycles-Repeat general visual in-
spection of the diagonal
brace and diagonal brace
fittings for any crack.
CONDITION 2: NO
CRACK FOUND IN DIAG-
ONAL BRACE OR DIAGO-
NAL BRACE FITTINGS (a)
-Before further flightCONDITION 3 (ACTION
1): Install the Upper Link
and Upper Link Pins if re-
moved.
CONDITION 3: NO SHIM
MIGRATION, NO SKIN
CRACK AND NO LOOSE
FASTENER.
3,000 flight cycles-CONDITION 3 (ACTION
2): Repeat inspections for
loose fasteners, skin
cracks and shim migra-
tions.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 2: March 01, 2021
24 of 105
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 25

Group 1, 5, Configuration 1:
Table 9: Inspection for loose fasteners, skin cracking and shim migration at the upper link drag fittings
and for cracks in the diagonal brace and diagonal brace fittings
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flightDo open-hole HFEC in-
spection of fastener holes
1-10 for cracks.
CONDITION 4: ANY
LOOSE FASTENER
FOUND ON FASTENERS
1-10 (a)
-Before further flightDo open-hole HFEC in-
spection on the loose bolt
hole(s) for cracks.
CONDITION 5: ANY
LOOSE FASTENER
FOUND ON FASTENERS
11-18 (a)
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair.
CONDITION 6: MAJOR
SHIM MIGRATION
FOUND (a)
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair.
CONDITION 7: ANY
CRACK FOUND IN DRAG
FITTINGS (a)
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair.
CONDITION 8: ANY
CRACK FOUND IN SKIN
(a)
-Before further flightCONDITION 9 (ACTION
1): Install new or service-
able bolts, new or kept
washers, and new nuts
for fastener holes where
fasteners were removed.
CONDITION 9: NO
CRACK FOUND IN SKIN
AND DRAG FITTINGS
DURING OPEN-HOLE
HFEC INSPECTION
-Before further flightCONDITION 9 (ACTION
2): Install the Upper Link
and Upper Link Pins if re-
moved.
3,000 flight cycles-CONDITION 9 (ACTION
3): Repeat inspections for
loose fasteners, skin
cracks and shim migra-
tions.
-Before further flightDo a torque check of fas-
teners on the affected
shim(s).
CONDITION 10: MINOR
SHIM MIGRATION
FOUND IN SKIN PANEL
SHIM (a)
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 2: March 01, 2021
25 of 105
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 26

Group 1, 5, Configuration 1:
Table 9: Inspection for loose fasteners, skin cracking and shim migration at the upper link drag fittings
and for cracks in the diagonal brace and diagonal brace fittings
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flightCONDITION 10.1 (AC-
TION 1): Trim affected
shim to the edge of the
fitting. Apply chemical
conversion coating on the
shim and fillet seal the
edge of the drag fitting.
CONDITION 10.1: ALL
BOLTS PASSED THE
TORQUE CHECK
-Before further flightCONDITION 10.1 (AC-
TION 2): Install the Upper
Link and Upper Link Pins
if removed.
3,000 flight cycles-CONDITION 10.1 (AC-
TION 3): Repeat inspec-
tions for loose fasteners,
skin cracks and shim mi-
grations.
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair.
CONDITION 10.2: ANY
BOLT FAILED THE
TORQUE CHECK
-Before further flightCONDITION 11 (ACTION
1): Trim affected shim to
the edge of the fitting.
Apply chemical conver-
sion coating on the shim
and fillet seal the edge of
the drag fitting.
CONDITION 11: MINOR
SHIM MIGRATION
FOUND IN SPAR SHIM (a)
-Before further flightCONDITION 11 (ACTION
2): Install the Upper Link
and Upper Link Pins if re-
moved.
3,000 flight cycles-CONDITION 11 (ACTION
3): Repeat inspections for
loose fasteners, skin
cracks and shim migra-
tions.
(a) More than one CONDITION can be applicable on each airplane.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 2: March 01, 2021
26 of 105
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 27

Group 1, Configuration 1:
Table 10: Inspect for cracks in the wing skin and drag fittings at the upper link drag fittings (Fastener
Locations 11-18)
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Within 3,000
flight cycles af-
ter the Revision
1 date of Re-
quirements Bul-
letin 757-
57A0073 RB
Before 8,400 to-
tal flight cycles
Do an open-hole HFEC
inspection of fastener
holes 11-18 for any crack.
(a)(b)
All airplanes
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair.
CONDITION 7: ANY
CRACK FOUND IN DRAG
FITTINGS (c)
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair.
CONDITION 8: ANY
CRACK FOUND IN SKIN
(c)
-Before further flightCONDITION 14 (ACTION
1): Install new or service-
able bolts, new or kept
washers, and new nuts.
CONDITION 14: NO
CRACK FOUND IN SKIN
AND DRAG FITTINGS.
-Before further flightCONDITION 14 (ACTION
2): Install the Upper Link
and Upper Link Pins if re-
moved.
8,400 flight cycles-CONDITION 14 (ACTION
3): Repeat open hole
HFEC inspection of fas-
tener holes 11-18 for any
crack. (a)(b)
(a) Accomplishment of an open-hole HFEC inspection of loose fastener hole(s) as a result of CONDITION
5 meets the requirements of this action for only the fastener hole(s) inspected.
(b) When this action occurs at the same time as a loose fastener inspection from Table 9, the loose fastener
inspection in Table 9 must be done first.
(c) More than one CONDITION can be applicable on each airplane.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 2: March 01, 2021
27 of 105
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 28

Group 1, Configuration 2:
Table 11: Inspect for cracks in the wing skin and drag fittings at the upper link drag fittings (Fastener
Locations 11-18)
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Within 3,000
flight cycles af-
ter the Revision
1 date of Re-
quirements Bul-
letin 757-
57A0073 RB
Before 14,000
total flight cycles
Do an open-hole HFEC
inspection of fastener
holes 11-18 for any crack.
(a)(b)
All airplanes
-Before further flightCONDITION 13 (ACTION
1): Replace any cracked
drag fitting with a new
part or contact The Boe-
ing Company for repair
instructions and do the
repair.
CONDITION 13: ANY
CRACK FOUND IN THE
DRAG FITTINGS DURING
OPEN-HOLE INSPEC-
TIONS (c)
-Before further flightCONDITION 13 (ACTION
2): Install the Upper Link
and Upper Link Pins if re-
moved.
12,000 flight cycles-CONDITION 13 (ACTION
3): Repeat open hole
HFEC inspection of fas-
tener holes 11-18 for any
crack. (a)(b)
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair.
CONDITION 8: ANY
CRACK FOUND IN SKIN
(c)
-Before further flightCONDITION 14 (ACTION
1): Install new or service-
able bolts, new or kept
washers, and new nuts.
CONDITION 14: NO
CRACK FOUND IN SKIN
AND DRAG FITTINGS
-Before further flightCONDITION 14 (ACTION
2): Install the Upper Link
and Upper Link Pins if re-
moved.
12,000 flight cycles-CONDITION 14 (ACTION
3): Repeat open hole
HFEC inspection of fas-
tener holes 11-18 for any
crack. (a)(b)
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 2: March 01, 2021
28 of 105
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 29

Group 1, Configuration 2:
Table 11: Inspect for cracks in the wing skin and drag fittings at the upper link drag fittings (Fastener
Locations 11-18)
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
(a) Accomplishment of an open-hole HFEC inspection of loose fastener hole(s) as a result of CONDITION
5 meets the requirements of this action for only the fastener hole(s) inspected.
(b) When this action occurs at the same time as a loose fastener inspection from Table 1, the loose fastener
inspection in Table 1 must be done first.
(c) More than one CONDITION can be applicable on each airplane.
Group 2-4:
Table 12: Inspect for cracks in the wing skin and drag fittings at the upper link drag fittings (Fastener
Locations 11-18)
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
-Within 3,000 flight cycles after the
Revision 1 date of Requirements
Bulletin 757-57A0073 RB
Do an open-hole HFEC
inspection of fastener
holes 11-18 for any crack.
(a)(b)
All airplanes
-Before further flightCONDITION 13 (ACTION
1): Replace any cracked
drag fitting with a new
part or contact The Boe-
ing Company for repair
instructions and do the
repair.
CONDITION 13: ANY
CRACK FOUND IN THE
DRAG FITTINGS DURING
OPEN-HOLE INSPEC-
TIONS (c)
-Before further flightCONDITION 13 (ACTION
2): Install the Upper Link
and Upper Link Pins if re-
moved.
12,000 flight cycles-CONDITION 13 (ACTION
3): Repeat open-hole
HFEC inspection of fas-
tener holes 11-18 for any
crack. (a)(b)
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair.
CONDITION 8: ANY
CRACK FOUND IN SKIN
(c)
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 2: March 01, 2021
29 of 105
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 30

Group 2-4:
Table 12: Inspect for cracks in the wing skin and drag fittings at the upper link drag fittings (Fastener
Locations 11-18)
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
-Before further flightCONDITION 14 (ACTION
1): Install new or service-
able bolts, new or kept
washers, and new nuts.
CONDITION 14: NO
CRACK FOUND IN SKIN
AND DRAG FITTINGS
-Before further flightCONDITION 14 (ACTION
2): Install the Upper Link
and Upper Link Pins if re-
moved.
12,000 flight cycles-CONDITION 14 (ACTION
3): Repeat open-hole
HFEC inspection of fas-
tener holes 11-18 for any
crack. (a)(b)
(a) Accomplishment of an open-hole HFEC inspection of loose fastener hole(s) as a result of CONDITION
5 meets the requirements of this action for only the fastener hole(s) inspected.
(b) When this action occurs at the same time as a loose fastener inspection from Table 1, the loose fastener
inspection in Table 1 must be done first.
(c) More than one CONDITION can be applicable on each airplane.
Group 5, Configuration 1:
Table 13: Inspect for cracks in the wing skin and drag fittings at the upper link drag fittings (Fastener
Locations 11-18)
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Within 3,000
flight cycles af-
ter the Revision
1 date of Re-
quirements Bul-
letin 757-
57A0073 RB
Before 5,500 to-
tal flight cycles
Do an open-hole HFEC
inspection of fastener
holes 11-18 for any crack.
(a)(b)
All airplanes
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair.
CONDITION 7: ANY
CRACK FOUND IN THE
DRAG FITTINGS (c)
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair.
CONDITION 8: ANY
CRACK FOUND IN SKIN
(c)
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 2: March 01, 2021
30 of 105
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 31

Group 5, Configuration 1:
Table 13: Inspect for cracks in the wing skin and drag fittings at the upper link drag fittings (Fastener
Locations 11-18)
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flightCONDITION 14 (ACTION
1): Install new or service-
able bolts, new or kept
washers, and new nuts.
CONDITION 14: NO
CRACK FOUND IN SKIN
AND DRAG FITTINGS
-Before further flightCONDITION 14 (ACTION
2): Install the Upper Link
and Upper Link Pins if re-
moved.
5,500 flight cycles-CONDITION 14 (ACTION
3): Repeat open-hole
HFEC inspection of fas-
tener holes 11-18 for any
crack. (a)(b)
(a) Accomplishment of an open-hole HFEC inspection of loose fastener hole(s) as a result of CONDITION
5 meets the requirements of this action for only the fastener hole(s) inspected.
(b) When this action occurs at the same time as a loose fastener inspection from Table 9, the loose fastener
inspection in Table 9 must be done first.
(c) More than one CONDITION can be applicable on each airplane.
Group 5, Configuration 2:
Table 14: Inspect for cracks in the wing skin and drag fittings at the upper link drag fittings (Fastener
Locations 11-18)
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Within 3,000
flight cycles af-
ter the Revision
1 date of Re-
quirements Bul-
letin 757-
57A0073 RB
Before 14,000
total flight cycles
Do an open-hole HFEC
inspection of fastener
holes 11-18 for any crack.
(a)(b)
All airplanes
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 2: March 01, 2021
31 of 105
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 32

Group 5, Configuration 2:
Table 14: Inspect for cracks in the wing skin and drag fittings at the upper link drag fittings (Fastener
Locations 11-18)
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flightCONDITION 13 (ACTION
1): Replace any cracked
drag fitting with a new
part or contact The Boe-
ing Company for repair
instructions and do the
repair.
CONDITION 13: ANY
CRACK FOUND IN DRAG
FITTINGS DURING OPEN-
HOLE INSPECTIONS (c)
-Before further flightCONDITION 13 (ACTION
2): Install the Upper Link
and Upper Link Pins if re-
moved.
6,000 flight cycles-CONDITION 13 (ACTION
3): Repeat open-hole
HFEC inspection of fas-
tener holes 11-18 for any
crack. (a)(b)
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair.
CONDITION 8: ANY
CRACK FOUND IN SKIN
(c)
-Before further flightCONDITION 14 (ACTION
1): Install new or service-
able bolts, new or kept
washers, and new nuts.
CONDITION 14: NO
CRACK FOUND IN SKIN
AND DRAG FITTINGS
-Before further flightCONDITION 14 (ACTION
2): Install the Upper Link
and Upper Link Pins if re-
moved.
6,000 flight cycles-CONDITION 14 (ACTION
3): Repeat open-hole
HFEC inspection of fas-
tener holes 11-18 for any
crack. (a)(b)
(a) Accomplishment of an open-hole HFEC inspection of loose fastener hole(s) as a result of CONDITION
5 meets the requirements of this action for only the fastener hole(s) inspected.
(b) When this action occurs at the same time as a loose fastener inspection from Table 1, the loose fastener
inspection in Table 1 must be done first.
(c) More than one CONDITION can be applicable on each airplane.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 2: March 01, 2021
32 of 105
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 33

Group 6-8, 11:
Table 15: Inspect for cracks in the wing skin and drag fittings at the upper link drag fittings (Fastener
Locations 11-18)
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
-Within 3,000 flight cycles after the
Revision 1 date of Requirements
Bulletin 757-57A0073 RB
Do an open-hole HFEC
inspection of fastener
holes 11-18 for any crack.
(a)(b)
All airplanes
-Before further flightCONDITION 13 (ACTION
1): Replace any cracked
drag fitting with a new
part or contact The Boe-
ing Company for repair
instructions and do the
repair.
CONDITION 13: ANY
CRACK FOUND IN THE
DRAG FITTINGS DURING
OPEN HOLE INSPEC-
TIONS (c)
-Before further flightCONDITION 13 (ACTION
2): Install the Upper Link
and Upper Link Pins if re-
moved.
6,000 flight cycles-CONDITION 13 (ACTION
3): Repeat open-hole
HFEC inspection of fas-
tener holes 11-18 for any
crack. (a)(b)
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair.
CONDITION 8: ANY
CRACK FOUND IN SKIN
(c)
-Before further flightCONDITION 14 (ACTION
1): Install new or service-
able bolts, new or kept
washers, and new nuts.
CONDITION 14: NO
CRACK FOUND IN SKIN
AND DRAG FITTINGS
-Before further flightCONDITION 14 (ACTION
2): Install the Upper Link
and Upper Link Pins if re-
moved.
6,000 flight cycles-CONDITION 14 (ACTION
3): Repeat open-hole
HFEC inspection of fas-
tener holes 11-18 for any
crack. (a)(b)
(a) Accomplishment of an open-hole HFEC inspection of loose fastener hole(s) as a result of CONDITION
5 meets the requirements of this action for only the fastener hole(s) inspected.
(b) When this action occurs at the same time as a loose fastener inspection from Table 1 or Table 2, the
loose fastener inspection in Table 1 or Table 2 must be done first.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 2: March 01, 2021
33 of 105
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 34

Group 6-8, 11:
Table 15: Inspect for cracks in the wing skin and drag fittings at the upper link drag fittings (Fastener
Locations 11-18)
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
(c) More than one CONDITION can be applicable on each airplane.
Group 9-10:
Table 16: Inspect for cracks in the wing skin and drag fittings at the upper link drag fittings (Fastener
Locations 11-18)
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
-Within 3,000 flight cycles after the
Revision 1 date of Requirements
Bulletin 757-57A0073 RB
Do an open-hole HFEC
inspection of fastener
holes 11-18 for any crack.
(a)(b)
All airplanes
-Before further flightCONDITION 13 (ACTION
1): Replace any cracked
drag fitting with a new
part or contact The Boe-
ing Company for repair
instructions and do the
repair.
CONDITION 13: ANY
CRACK FOUND IN DRAG
FITTINGS DURING OPEN
HOLE INSPECTIONS (c)
-Before further flightCONDITION 13 (ACTION
2): Install the Upper Link
and Upper Link Pins if re-
moved.
9,000 flight cycles-CONDITION 13 (ACTION
3): Repeat open-hole
HFEC inspection of fas-
tener holes 11-18 for any
crack. (a)(b)
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair.
CONDITION 8: ANY
CRACK FOUND IN SKIN
(c)
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 2: March 01, 2021
34 of 105
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 35

Group 9-10:
Table 16: Inspect for cracks in the wing skin and drag fittings at the upper link drag fittings (Fastener
Locations 11-18)
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
-Before further flightCONDITION 14 (ACTION
1): Install new or service-
able bolts, new or kept
washers, and new nuts.
CONDITION 14: NO
CRACK FOUND IN SKIN
AND DRAG FITTINGS
-Before further flightCONDITION 14 (ACTION
2): Install the Upper Link
and Upper Link Pins if re-
moved.
9,000 flight cycles-CONDITION 14 (ACTION
3): Repeat open-hole
HFEC inspection of fas-
tener holes 11-18 for any
crack. (a)(b)
(a) Accomplishment of an open-hole HFEC inspection of loose fastener hole(s) as a result of CONDITION
5 meets the requirements of this action for only the fastener hole(s) inspected.
(b) When this action occurs at the same time as a loose fastener inspection from Table 1 or Table 2, the
loose fastener inspection in Table 1 or Table 2 must be done first.
(c) More than one CONDITION can be applicable on each airplane.
4. APPROVAL
This Requirements Bulletin was examined by the Federal Aviation Administration (FAA). The changes
specified in this document comply with the applicable regulations and are FAA approved, as well as European
Union Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved
airplanes listed in this Requirements Bulletin effectivity. This document and its approval were based on the
airplane in its original Boeing delivery configuration or as modified by other Boeing changes.
If an airplane has a non-Boeing modification or repair that affects a component or system also affected by
this Requirements Bulletin, the operator is responsible for obtaining appropriate regulatory agency approval
before incorporating this Requirements Bulletin.
In addition the Manager of the FAA Los Angeles ACO Branch approves the actions identified in this bulletin
revision as an alternative method of compliance to paragraph (g) of AD 2020-21-17. All provisions of AD
2020-21-17 that are not specifically referenced in the above statement remain fully applicable and must be
complied with.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 2: March 01, 2021
35 of 105
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 36

Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 2: March 01, 2021
36 of 105
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT
BLANK PAGE

### Page 37

5.    ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL INFORMATION
NOTE: 3. Unless shown differently, these dimensions and tolerances are used:
– Linear dimensions are in inches
– Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus
or minus 0.03 inch
– Tolerance on rivet and bolt edge margin is plus or minus 0.05 inch
– Angular tolerance is plus or minus 2 degrees
– Hole dimensions for standard solid rivets and fasteners are in Structural Repair
Manual (SRM) Chapter 51
– Torque Values:
— Values for structural fasteners are given in 757 Structural Repair Manual,
Chapter 51.
— Values for airframe maintenance tasks are included in Chapter 20 of 757
Aircraft Maintenance Manual (AMM).
— Values for electrical maintenance tasks are included in Chapter 20 of
Standard Wiring Practices Manual (SWPM).
— Values for engine maintenance tasks are included in Chapter 70 of 757
Aircraft Maintenance Manual (AMM).
— Non-standard torque values for maintenance tasks are included in the
applicable installation step.
4. Use the approved fastener, process and material substitutions in accordance with
SRM Chapter 51.
5. If the length of any fastener specified in this service bulletin does not meet installation
standards given in SRM Chapter 51, then a fastener of the same specification, or
an approved substitute, with a length which meets the installation standards given
in SRM Chapter 51 may be used. In addition, washers may be installed for fastener
grip length in accordance with SRM Chapter 51. Refer to SOPM 20-50-01 for alternate
full threaded fasteners (screws) needed for installation in this service bulletin.
6. A Detailed Inspection is defined as: An intensive examination of a specific item,
installation, or assembly to detect damage, failure, or irregularity. Available lighting
is normally supplemented with a direct source of good lighting at an intensity deemed
appropriate. Inspection aids such as mirrors, magnifying lenses, etc. may be
necessary. Surface cleaning and elaborate procedures may be required.
7. A General Visual Inspection is defined as: A visual examination of an interior or
exterior area, installation or assembly to detect obvious damage, failure or irregularity.
This level of inspection is made from within touching distance unless otherwise
specified. A mirror may be necessary to enhance visual access to all exposed surfaces
in the inspection area. This level of inspection is made under normally available
lighting conditions such as daylight, hangar lighting, flashlight or drop-light and may
require removal or opening of access panels or doors. Stands, ladders or platforms
may be required to gain proximity to the area being checked.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 2: March 01, 2021
37 of 105
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 38

8. These work instructions refer to procedures included in other Boeing documents.
When the words "refer to" are used and the operator has an accepted alternative
procedure, the accepted alternative procedure can be used. When the words "in
accordance with" are included in the instruction, the procedure in the Boeing document
must be used.
9. Boeing Service Letter 757-SL-51-022, Damage Reporting and Repair Plan/Design
Guidelines, is an acceptable procedure to request information from Boeing for
additional structural repair instructions. The Service Letter describes what information
must be provided to Boeing before a structural repair can be provided.
12. If it is necessary to remove more parts for access, you can remove those parts. If
you can get access without removing identified parts, it is not necessary to remove
all of the identified parts. Jacking and shoring limitations must be observed.
13. Where the work instructions include installation of a kept part, a new or serviceable
part with the same part number can be installed as an alternative to the kept part.
17. When more than one OPTION is given for a CONDITION, do only one of the OPTION
numbers. When more than one ACTION is given for a CONDITION or an OPTION,
do all of the ACTION numbers for that CONDITION or OPTION.
18. The compliance times for the actions in Work Instructions are in Compliance.
19. This is an Enhanced Required for Compliance document. There will be a separate
Service Bulletin (SB) and a separate Requirements Bulletin (RB). If an RB is mandated
by an Airworthiness Directive (AD), then all applicable requirements specified in the
RB must be done. For the related SB, some locations are marked RC Start and RC
End to identify the requirements that are restated from the RB. For the related SB,
the areas between RC Start and RC End, including sub-steps and any figures
identified between RC Start and RC End, must be done to comply with the AD.
Therefore, an Alternative Method of Compliance (AMOC) is required for any deviations
to steps between RC Start and RC End, including substeps and identified figures.
For the related SB, the steps not between RC Start and RC End may be deviated
from using accepted methods in accordance with the operator's maintenance or
inspection program without obtaining approval of an AMOC; this is provided that the
steps between RC Start and RC End, including sub-steps and identified figures, can
still be done as specified, and the airplane can be put back in an airworthy condition.
Figures not required for compliance are omitted from the RB.
20. This is an Enhanced Required for Compliance document. The Boeing processes
used to create the Service Bulletin (SB) and the Requirements Bulletin (RB) ensure
that the information between "RC Start" and "RC End" in the SB are identical to the
information in the same sections (Compliance, Work Instructions...) of the RB which
the SB refers to as the related document.
21. All of the inspections given in the Work Instructions can be done with the engine
installed or removed.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 2: March 01, 2021
38 of 105
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 39

B. WORK INSTRUCTIONS
Actions required for compliance:
1. Requirements
PARTS are identified as follows:
TitlePart
OPEN ACCESSPART 1
LOOSE FASTENER, SKIN CRACK AND SHIM MIGRA-
TION INSPECTIONS
PART 2
BOLTS 1-10 OPEN-HOLE HFEC INSPECTIONPART 3
LOOSE BOLT 11-18 OPEN-HOLE HFEC INSPECTIONPART 4
BOLT INSTALLATIONPART 5
SHIM BOLT TORQUE CHECKPART 6
SHIM TRIMMINGPART 7
BOLTS 11-18 OPEN-HOLE HFEC INSPECTIONPART 8
DRAG FITTING REPLACEMENTPART 9
OPEN ACCESS FOR GENERAL VISUAL INSPEC-
TION OF THE DIAGONAL BRACE AND DIAGONAL
BRACE FITTINGS.
PART 10
GENERAL VISUAL INSPECTION OF THE DIAGONAL
BRACE AND DIAGONAL BRACE FITTINGS FOR ANY
CRACK.
PART 11
CLOSE ACCESS FOR GENERAL VISUAL INSPEC-
TION OF THE DIAGONAL BRACE AND DIAGONAL
BRACE FITTINGS.
PART 12
CLOSE ACCESSPART 13
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 2: March 01, 2021
39 of 105
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 40

Group 1, Configuration 2; Group 2-4; Group 5, Configuration 2; Group 6-9:
Table 1 (Related to Compliance Table 1): Inspection for loose fasteners, skin cracking and shim migration
at the upper link drag fittings and for cracks in the diagonal brace and diagonal brace fittings
Refer to the listed proce-
dures in SB 757-57A0073
Original Issue or later
approved revisions as an
accepted procedure.
Method of ComplianceActionCondition
PART 10-ACTION 1: Do a general
visual inspection of the di-
agonal brace and diagonal
brace fittings for any crack.
All Airplanes
PART 11Figures 9, 10
PART 1-ACTION 2: Do inspections
for loose fasteners, skin
cracks and shim migra-
tions.
PART 2Figures 1-4, 11, 12
--Contact The Boeing Com-
pany for repair instructions
and do the repair.
CONDITION 1: ANY
CRACK FOUND IN DIAG-
ONAL BRACE OR DIAGO-
NAL BRACE FITTINGS (a)
PART 11Figures 9, 10Repeat general visual in-
spection of the diagonal
brace and diagonal brace
fittings for any crack.
CONDITION 2: NO
CRACK FOUND IN DIAG-
ONAL BRACE OR DIAGO-
NAL BRACE FITTINGS (a)
PART 13-ACTION 1: Install the Up-
per Link and Upper Link
Pins if removed.
CONDITION 3: NO SHIM
MIGRATION, NO SKIN
CRACK AND NO LOOSE
FASTENER. PART 2Figures 1-4, 11, 12ACTION 2: Repeat inspec-
tions for loose fasteners,
skin cracks and shim migra-
tions.
PART 3Figures 5, 6Do open-hole HFEC in-
spection of fastener holes
1-10 for cracks.
CONDITION 4: ANY
LOOSE FASTENER
FOUND ON FASTENERS
1-10 (a)
PART 4Figures 7, 8Do open-hole HFEC in-
spection on the loose bolt
hole(s) for cracks.
CONDITION 5: ANY
LOOSE FASTENER
FOUND ON FASTENERS
11-18 (a)
--Contact The Boeing Com-
pany for repair instructions
and do the repair.
CONDITION 6: MAJOR
SHIM MIGRATION
FOUND (a)
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 2: March 01, 2021
40 of 105
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 41

Group 1, Configuration 2; Group 2-4; Group 5, Configuration 2; Group 6-9:
Table 1 (Related to Compliance Table 1): Inspection for loose fasteners, skin cracking and shim migration
at the upper link drag fittings and for cracks in the diagonal brace and diagonal brace fittings
Refer to the listed proce-
dures in SB 757-57A0073
Original Issue or later
approved revisions as an
accepted procedure.
Method of ComplianceActionCondition
--OPTION 1: Contact The
Boeing Company for repair
instructions and do the re-
pair.
CONDITION 7: ANY
CRACK FOUND IN DRAG
FITTINGS (a)
PART 9-OPTION 2 (ACTION 1):
Replace any cracked drag
fitting with a new part.
PART 13-OPTION 2 (ACTION 2):
Install the Upper Link and
Upper Link Pins if re-
moved.
PART 2Figures 1-4, 11, 12OPTION 2 (ACTION 3):
Repeat inspections for
loose fasteners, skin
cracks and shim migra-
tions.
--Contact The Boeing Com-
pany for repair instructions
and do the repair.
CONDITION 8: ANY
CRACK FOUND IN SKIN
(a)
PART 5-CONDITION 9 (ACTION
1): Install new or service-
able bolts, new or kept
washers, and new nuts.
CONDITION 9: NO
CRACK FOUND IN SKIN
AND DRAG FITTINGS
DURING OPEN-HOLE
HFEC INSPECTION (a) PART 13-CONDITION 9 (ACTION
2): Install the Upper Link
and Upper Link Pins if re-
moved.
PART 2Figures 1-4, 11, 12CONDITION 9 (ACTION
3): Repeat inspections for
loose fasteners, skin
cracks and shim migra-
tions.
PART 6Figures 13-16Do a torque check of fas-
teners on the affected
shim(s).
CONDITION 10: MINOR
SHIM MIGRATION
FOUND IN SKIN PANEL
SHIM (a)
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 2: March 01, 2021
41 of 105
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 42

Group 1, Configuration 2; Group 2-4; Group 5, Configuration 2; Group 6-9:
Table 1 (Related to Compliance Table 1): Inspection for loose fasteners, skin cracking and shim migration
at the upper link drag fittings and for cracks in the diagonal brace and diagonal brace fittings
Refer to the listed proce-
dures in SB 757-57A0073
Original Issue or later
approved revisions as an
accepted procedure.
Method of ComplianceActionCondition
PART 7-CONDITION 10.1 (AC-
TION 1): Trim affected
shim to the edge of the fit-
ting. Apply chemical con-
version coating on the
shim and fillet seal the
edge of the drag fitting.
CONDITION 10.1: ALL
BOLTS PASSED THE
TORQUE CHECK
PART 13-CONDITION 10.1 (AC-
TION 2): Install the Upper
Link and Upper Link Pins
if removed.
PART 2Figures 1-4, 11, 12CONDITION 10.1 (AC-
TION 3): Repeat inspec-
tions for loose fasteners,
skin cracks and shim migra-
tions.
--Contact The Boeing Com-
pany for repair instructions
and do the repair.
CONDITION 10.2: ANY
BOLT FAILED THE
TORQUE CHECK
PART 7-CONDITION 11 (ACTION
1): Trim affected shim to
the edge of the fitting. Ap-
ply chemical conversion
coating on the shim and
fillet seal the edge of the
drag fitting.
CONDITION 11: MINOR
SHIM MIGRATION
FOUND IN SPAR SHIM
(a)
PART 13-CONDITION 11 (ACTION
2): Install the Upper Link
and Upper Link Pins if re-
moved.
PART 2Figures 1-4, 11, 12CONDITION 11 (ACTION
3): Repeat inspections for
loose fasteners, skin
cracks and shim migra-
tions.
(a) More than one CONDITION can be applicable to each airplane.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 2: March 01, 2021
42 of 105
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 43

Group 10-11:
Table 2 (Related to Compliance Table 2): Inspection for loose fasteners, skin cracking and shim migration
at the upper link drag fittings and for cracks in the diagonal brace and diagonal brace fittings
Refer to the listed proce-
dures in SB 757-57A0073
Original Issue or later
approved revisions as an
accepted procedure.
Method of ComplianceActionCondition
PART 10-ACTION 1: Do a general
visual inspection of the di-
agonal brace and diagonal
brace fittings for any crack.
All airplanes
PART 11Figures 9, 10
PART 1-ACTION 2: Do inspections
for loose fasteners, skin
cracks and shim migra-
tions.
PART 2Figures 1-4, 11, 12
--Contact The Boeing Com-
pany for repair instructions
and do the repair.
CONDITION 1: ANY
CRACK FOUND IN DIAG-
ONAL BRACE OR DIAGO-
NAL BRACE FITTINGS (a)
PART 11Figures 9, 10Repeat general visual in-
spection of the diagonal
brace and diagonal brace
fittings for any crack.
CONDITION 2: NO
CRACK FOUND IN DIAG-
ONAL BRACE OR DIAGO-
NAL BRACE FITTINGS (a)
PART 13-CONDITION 3 (ACTION
1): Install the Upper Link
and Upper Link Pins if re-
moved.
CONDITION 3: NO SHIM
MIGRATION, NO SKIN
CRACK AND NO LOOSE
FASTENER.
PART 2Figures 1-4, 11, 12CONDITION 3 (ACTION
2): Repeat inspections for
loose fasteners, skin
cracks and shim migra-
tions.
--Contact The Boeing Com-
pany for repair instructions
and do the repair.
CONDITION 6: MAJOR
SHIM MIGRATION
FOUND (a)
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 2: March 01, 2021
43 of 105
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 44

Group 10-11:
Table 2 (Related to Compliance Table 2): Inspection for loose fasteners, skin cracking and shim migration
at the upper link drag fittings and for cracks in the diagonal brace and diagonal brace fittings
Refer to the listed proce-
dures in SB 757-57A0073
Original Issue or later
approved revisions as an
accepted procedure.
Method of ComplianceActionCondition
--OPTION 1: Contact The
Boeing Company for repair
instructions and do the re-
pair.
CONDITION 7: ANY
CRACK FOUND IN DRAG
FITTINGS (a)
PART 9-OPTION 2 (ACTION 1):
Replace any cracked drag
fitting with a new part.
PART 13-OPTION 2 (ACTION 2):
Install the Upper Link and
Upper Link Pins if re-
moved.
PART 2Figures 1-4, 11, 12OPTION 2 (ACTION 3):
Repeat inspections for
loose fasteners, skin
cracks and shim migra-
tions.
--Contact The Boeing Com-
pany for repair instructions
and do the repair.
CONDITION 8: ANY
CRACK FOUND IN SKIN
(a)
PART 6Figures 17-20Do a torque check of fas-
teners on the affected
shim(s).
CONDITION 10: MINOR
SHIM MIGRATION
FOUND IN SKIN PANEL
SHIM (a)
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 2: March 01, 2021
44 of 105
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 45

Group 10-11:
Table 2 (Related to Compliance Table 2): Inspection for loose fasteners, skin cracking and shim migration
at the upper link drag fittings and for cracks in the diagonal brace and diagonal brace fittings
Refer to the listed proce-
dures in SB 757-57A0073
Original Issue or later
approved revisions as an
accepted procedure.
Method of ComplianceActionCondition
PART 7-CONDITION 10.1 (AC-
TION 1): Trim affected
shim to the edge of the fit-
ting. Apply chemical con-
version coating on the
shim and fillet seal the
edge of the drag fitting.
CONDITION 10.1: ALL
BOLTS PASSED THE
TORQUE CHECK
PART 13-CONDITION 10.1 (AC-
TION 2): Install the Upper
Link and Upper Link Pins
if removed.
PART 2Figures 1-4, 11, 12CONDITION 10.1 (AC-
TION 3): Repeat inspec-
tions for loose fasteners,
skin cracks and shim migra-
tions.
--Contact The Boeing Com-
pany for repair instructions
and do the repair.
CONDITION 10.2: ANY
BOLT FAILED THE
TORQUE CHECK
PART 7-CONDITION 11 (ACTION
1): Trim affected shim to
the edge of the fitting. Ap-
ply chemical conversion
coating on the shim and
fillet seal the edge of the
drag fitting.
CONDITION 11: MINOR
SHIM MIGRATION
FOUND IN SPAR SHIM
(a)
PART 13-CONDITION 11 (ACTION
2): Install the Upper Link
and Upper Link Pins if re-
moved.
PART 2Figures 1-4, 11, 12CONDITION 11 (ACTION
3): Repeat inspections for
loose fasteners, skin
cracks and shim migra-
tions.
--Contact The Boeing Com-
pany for repair instructions
and do the repair.
CONDITION 12: ANY
LOOSE FASTENER
FOUND (a)
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 2: March 01, 2021
45 of 105
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 46

Group 10-11:
Table 2 (Related to Compliance Table 2): Inspection for loose fasteners, skin cracking and shim migration
at the upper link drag fittings and for cracks in the diagonal brace and diagonal brace fittings
Refer to the listed proce-
dures in SB 757-57A0073
Original Issue or later
approved revisions as an
accepted procedure.
Method of ComplianceActionCondition
(a) More than one CONDITION can apply to each airplane.
Group 1, Configuration 2; Group 2-4; Group 5, Configuration 2; Group 6-11:
Table 3 (Related to Compliance Tables 3-6): Inspect for cracks in the wing skin and drag fittings at the
upper link drag fittings (Fastener Locations 1-10)
Refer to the listed proce-
dures in SB 757-57A0073
Original Issue or later
approved revisions as an
accepted procedure.
Method of ComplianceActionCondition
PART 1-Do open-hole HFEC in-
spection of fastener holes
1-10 for cracks. (a)(b)
All airplanes
PART 3Figures 5, 6
--OPTION 1: Contact The
Boeing Company for repair
instructions and do the re-
pair.
CONDITION 7: ANY
CRACK FOUND IN DRAG
FITTINGS (c)
PART 9-OPTION 2 (ACTION 1):
Replace any cracked drag
fitting with a new part.
PART 13-OPTION 2 (ACTION 2):
Install the Upper Link and
Upper Link Pins if re-
moved.
PART 3Figures 5, 6OPTION 2 (ACTION 3):
Repeat open-hole HFEC
inspection of fastener
holes 1-10. (a)(b)
--Contact The Boeing Com-
pany for repair instructions
and do the repair.
CONDITION 8: ANY
CRACK FOUND IN SKIN
(c)
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 2: March 01, 2021
46 of 105
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 47

Group 1, Configuration 2; Group 2-4; Group 5, Configuration 2; Group 6-11:
Table 3 (Related to Compliance Tables 3-6): Inspect for cracks in the wing skin and drag fittings at the
upper link drag fittings (Fastener Locations 1-10)
Refer to the listed proce-
dures in SB 757-57A0073
Original Issue or later
approved revisions as an
accepted procedure.
Method of ComplianceActionCondition
PART 5-CONDITION 9 (ACTION
1): Install new or service-
able bolts, new or kept
washers, and new nuts.
CONDITION 9: NO
CRACK FOUND IN SKIN
AND DRAG FITTINGS
DURING OPEN-HOLE
HFEC INSPECTION PART 13-CONDITION 9 (ACTION
2): Install the Upper Link
and Upper Link Pins if re-
moved.
PART 3Figures 5, 6CONDITION 9 (ACTION
3): Repeat open-hole
HFEC inspection of fasten-
er holes 1-10. (a)(b)
(a) Accomplishment of an open-hole HFEC inspection of fastener holes 1-10 as a result of CONDITION 4
meets the requirements of this action.
(b) As of the Revision 1 date of 757-57A0073 RB, when this action occurs at the same time as a loose fastener
inspection from Table 1 or Table 2, the loose fastener inspection in Table 1 or Table 2 must be done first.
(c) More than one CONDITION can apply to each airplane.
Group 1, Configuration 2; Group 2-4; Group 5, Configuration 2; Group 6-11:
Table 4 (Related to Compliance Tables 11-12 and 14-16): Inspect for cracks in the wing skin and drag
fittings at the upper link drag fittings (Fastener Locations 11-18)
Refer to the listed proce-
dures in SB 757-57A0073
Revision 1 or later ap-
proved revisions as an
accepted procedure.
Method of ComplianceActionCondition
PART 1-Do an open-hole HFEC in-
spection of fastener holes
11-18 for any crack. (a)(b)
All airplanes
PART 8Figures 21, 22
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 2: March 01, 2021
47 of 105
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 48

Group 1, Configuration 2; Group 2-4; Group 5, Configuration 2; Group 6-11:
Table 4 (Related to Compliance Tables 11-12 and 14-16): Inspect for cracks in the wing skin and drag
fittings at the upper link drag fittings (Fastener Locations 11-18)
Refer to the listed proce-
dures in SB 757-57A0073
Revision 1 or later ap-
proved revisions as an
accepted procedure.
Method of ComplianceActionCondition
PART 9-CONDITION 13 (ACTION
1): Replace any cracked
drag fitting with a new part
or contact The Boeing
Company for repair instruc-
tions and do the repair.
CONDITION 13: ANY
CRACK FOUND IN THE
DRAG FITTINGS DURING
OPEN-HOLE INSPEC-
TIONS (c)
PART 13-CONDITION 13 (ACTION
2): Install the Upper Link
and Upper Link Pins if re-
moved.
PART 8Figures 21, 22CONDITION 13 (ACTION
3): Repeat open-hole
HFEC inspection of fasten-
er holes 11-18 for any
crack. (a)(b)
--Contact The Boeing Com-
pany for repair instructions
and do the repair.
CONDITION 8: ANY
CRACK FOUND IN SKIN
(c)
PART 5-CONDITION 14 (ACTION
1): Install new or service-
able bolts, new or kept
washers, and new nuts.
CONDITION 14: NO
CRACK FOUND IN SKIN
AND DRAG FITTINGS
PART 13-CONDITION 14 (ACTION
2): Install the Upper Link
and Upper Link Pins if re-
moved.
PART 8Figures 21, 22CONDITION 14 (ACTION
3): Repeat open-hole
HFEC inspection of fasten-
er holes 11-18 for any
crack. (a)(b)
(a) Accomplishment of an open-hole HFEC inspection of loose fastener hole(s) as a result of CONDITION 5
meets the requirement of this action for only the fastener hole(s) inspected
(b) When this action occurs at the same time as a loose fastener inspection from Table 1 or Table 2, the loose
fastener inspection in Table 1 or Table 2 must be done first.
(c) More than one CONDITION can apply to each airplane.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 2: March 01, 2021
48 of 105
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 49

Group 1, 5, Configuration 1:
Table 5 (Related to Compliance Table 9): Inspection for loose fasteners, skin cracking and shim migration
at the upper link drag fittings and for cracks in the diagonal brace and diagonal brace fittings
Refer to the listed proce-
dures in SB 757-57A0073
Original Issue or later
approved revisions as an
accepted procedure.
Method of ComplianceActionCondition
PART 10-ACTION 1: Do a general
visual inspection of the di-
agonal brace and diagonal
brace fittings for any crack.
All Airplanes
PART 11Figures 9, 10
PART 1-ACTION 2: Do inspections
for loose fasteners, skin
cracks and shim migra-
tions.
PART 2Figures 1-4, 11, 12
--Contact The Boeing Com-
pany for repair instructions
and do the repair
CONDITION 1: ANY
CRACK FOUND IN DIAG-
ONAL BRACE OR DIAGO-
NAL BRACE FITTINGS (a)
PART 11Figures 9, 10Repeat general visual in-
spection of the diagonal
brace and diagonal brace
fittings for any crack.
CONDITION 2: NO
CRACK FOUND IN DIAG-
ONAL BRACE OR DIAGO-
NAL BRACE FITTINGS (a)
PART 13-CONDITION 3 (ACTION
1): Install the Upper Link
and Upper Link Pins if re-
moved.
CONDITION 3: NO SHIM
MIGRATION, NO SKIN
CRACK AND NO LOOSE
FASTENER.
PART 2Figures 1-4, 11, 12CONDITION 3 (ACTION
2): Repeat inspections for
loose fasteners, skin
cracks and shim migra-
tions.
PART 3Figures 5, 6Do open-hole HFEC in-
spection of fastener holes
1-10 for cracks.
CONDITION 4: ANY
LOOSE FASTENER
FOUND ON FASTENERS
1-10 (a)
PART 4Figures 7, 8Do open-hole HFEC in-
spection on the loose bolt
hole(s) for cracks.
CONDITION 5: ANY
LOOSE FASTENER
FOUND ON FASTENERS
11-18 (a)
--Contact The Boeing Com-
pany for repair instructions
and do the repair.
CONDITION 6: MAJOR
SHIM MIGRATION
FOUND (a)
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 2: March 01, 2021
49 of 105
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 50

Group 1, 5, Configuration 1:
Table 5 (Related to Compliance Table 9): Inspection for loose fasteners, skin cracking and shim migration
at the upper link drag fittings and for cracks in the diagonal brace and diagonal brace fittings
Refer to the listed proce-
dures in SB 757-57A0073
Original Issue or later
approved revisions as an
accepted procedure.
Method of ComplianceActionCondition
--Contact The Boeing Com-
pany for repair instructions
and do the repair.
CONDITION 7: ANY
CRACK FOUND IN DRAG
FITTINGS (a)
--Contact The Boeing Com-
pany for repair instructions
and do the repair.
CONDITION 8: ANY
CRACK FOUND IN SKIN
(a)
PART 5-CONDITION 9 (ACTION
1): Install new or service-
able bolts, new or kept
washers, and new nuts.
CONDITION 9: NO
CRACK FOUND IN SKIN
AND DRAG FITTINGS
DURING OPEN-HOLE
HFEC INSPECTION (a) PART 13-CONDITION 9 (ACTION
2): Install the Upper Link
and Upper Link Pins if re-
moved.
PART 2Figures 1-4, 11, 12CONDITION 9 (ACTION
3): Repeat inspections for
loose fasteners, skin
cracks and shim migra-
tions.
PART 6Figures 13-16Do a torque check of fas-
teners on the affected
shim(s).
CONDITION 10: MINOR
SHIM MIGRATION
FOUND IN SKIN PANEL
SHIM (a)
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 2: March 01, 2021
50 of 105
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 51

Group 1, 5, Configuration 1:
Table 5 (Related to Compliance Table 9): Inspection for loose fasteners, skin cracking and shim migration
at the upper link drag fittings and for cracks in the diagonal brace and diagonal brace fittings
Refer to the listed proce-
dures in SB 757-57A0073
Original Issue or later
approved revisions as an
accepted procedure.
Method of ComplianceActionCondition
PART 7-CONDITION 10.1 (AC-
TION 1): Trim affected
shim to the edge of the fit-
ting. Apply chemical con-
version coating on the
shim and fillet seal the
edge of the drag fitting.
CONDITION 10.1: ALL
BOLTS PASSED THE
TORQUE CHECK
PART 13-CONDITION 10.1 (AC-
TION 2): Install the Upper
Link and Upper Link Pins
if removed.
PART 2Figures 1-4, 11, 12CONDITION 10.1 (AC-
TION 3): Repeat inspec-
tions for loose fasteners,
skin cracks and shim migra-
tions.
--Contact The Boeing Com-
pany for repair instructions
and do the repair.
CONDITION 10.2: ANY
BOLT FAILED THE
TORQUE CHECK
PART 7-CONDITION 11 (ACTION
1): Trim affected shim to
the edge of the fitting. Ap-
ply chemical conversion
coating on the shim and
fillet seal the edge of the
drag fitting.
CONDITION 11: MINOR
SHIM MIGRATION
FOUND IN SPAR SHIM
(a)
PART 13-CONDITION 11 (ACTION
2): Install the Upper Link
and Upper Link Pins if re-
moved.
PART 2Figures 1-4, 11, 12CONDITION 11 (ACTION
3): Repeat inspections for
loose fasteners, skin
cracks and shim migra-
tions.
(a) More than one CONDITION can be applicable to each airplane.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 2: March 01, 2021
51 of 105
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 52

Group 1, 5, Configuration 1:
Table 6 (Related to Compliance Table 7-8): Inspect for cracks in the wing skin and drag fittings at the
upper link drag fittings (Fastener Locations 1-10)
Refer to the listed proce-
dures in SB 757-57A0073
Original Issue or later
approved revisions as an
accepted procedure.
Method of ComplianceActionCondition
PART 1-Do open-hole HFEC in-
spection of fastener holes
1-10 for cracks. (a)(b)
All airplanes
PART 3Figures 5, 6
--Contact The Boeing Com-
pany for repair instructions
and do the repair.
CONDITION 7 ANY
CRACK FOUND IN DRAG
FITTINGS (c)
--Contact The Boeing Com-
pany for repair instructions
and do the repair.
CONDITION 8: ANY
CRACK FOUND IN SKIN
(c)
PART 5-CONDITION 9 (ACTION
1): Install new or service-
able bolts, new or kept
washers, and new nuts.
CONDITION 9: NO
CRACK FOUND IN SKIN
AND DRAG FITTINGS
DURING OPEN-HOLE
HFEC INSPECTION PART 13-CONDITION 9 (ACTION
2): Install the Upper Link
and Upper Link Pins if re-
moved.
PART 3Figures 5, 6CONDITION 9 (ACTION
3): Repeat open-hole
HFEC inspection of fasten-
er holes 1-10. (a)(b)
(a) Accomplishment of an open-hole HFEC inspection of fastener holes 1-10 as a result of CONDITION 4
meets the requirements of this action.
(b) As of the Revision 1 date of 757-57A0073 RB, when this action occurs at the same time as a loose fastener
inspection from Table 9, the loose fastener inspection in Table 9 must be done first.
(c) More than one CONDITION can be applicable to each airplane.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 2: March 01, 2021
52 of 105
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 53

Group 1, 5, Configuration 1:
Table 7 (Related to Compliance Table 10 and Table 13): Inspect for cracks in the wing skin and drag fittings
at the upper link drag fittings (Fastener Locations 11-18)
Refer to the listed proce-
dures in SB 757-57A0073
Revision 1 or later ap-
proved revisions as an
accepted procedure.
Method of ComplianceActionCondition
PART 1-Do an open-hole HFEC in-
spection of fastener holes
11-18 for any crack. (a)(b)
All airplanes
PART 8Figures 21, 22
--Contact The Boeing Com-
pany for repair instructions
and do the repair.
CONDITION 7: ANY
CRACK FOUND IN DRAG
FITTINGS (c)
--Contact The Boeing Com-
pany for repair instructions
and do the repair.
CONDITION 8: ANY
CRACK FOUND IN SKIN
(c)
PART 5-CONDITION 14 (ACTION
1): Install new or service-
able bolts, new or kept
washers, and new nuts.
CONDITION 14: NO
CRACK FOUND IN SKIN
AND DRAG FITTINGS
PART 13-CONDITION 14 (ACTION
2): Install the Upper Link
and Upper Link Pins if re-
moved.
PART 8Figures 21, 22CONDITION 14 (ACTION
3): Repeat open-hole
HFEC inspection of fasten-
er holes 11-18 for any
crack. (a)(b)
(a) Accomplishment of an open-hole HFEC inspection of loose fastener hole(s) as a result of CONDITION 5
meets the requirement of this action for only the fastener hole(s) inspected
(b) When this action occurs at the same time as a loose fastener inspection from Table 9, the loose fastener
inspection in Table 9 must be done first.
(c) More than one CONDITION can be applicable to each airplane.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 2: March 01, 2021
53 of 105
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 54 (OCR)

REQUIREMENTS BULLETIN 757-57A0073
ALERT  ALERT
LEFT WING
12 18 LOCATIONS
PRATT AND WHITNEY STRUT SHOWN,  2559950
ROLLS ROYCE STRUT SIMILAR
FIGURE 1: LEFT WING - DRAG FITTINGS AND WING UPPER SKIN - LOOSE FASTENER INSPECTION
(SHEET 1 OF 2)
Original Issue: July 14, 2017
Revision 2 March 01, 2021  Export Controlled ECCN: 9E991  Copyright © Unpublished  757-57A0073 RB
Work - See page 1 for details.  54 of 105

### Page 55

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
More DataQtyIdentificationNameTaskStep
(a)18-FastenersInspect1
(c)--FastenerRemove
(b)18-FastenersInspect2
(c)--FastenerRemove
(a) Do a general visual inspection for any loose fastener at all 18 locations. A fastener is loose if any of the
following apply:
– the fastener head is protruding from the skin
– there is a discoloration adjacent to or around the fastener and cracked paint all the way around the
fastener head (if painted)
– there is a streak of dirt or oil aft of the fastener coming from the fastener hole
Refer to APPENDIX B of the service bulletin for supplemental information on doing the inspection.
(b) Do a detailed inspection for any loose fastener at all 18 locations by applying torque to the heads of the
fasteners. Apply a minimum of 30 in-lbs of torque to the fastener head. Do not secure the nut to do the
inspection. If fastener rotation occurs during the inspection, the fastener is loose.
(c) Remove and discard any loose bolts and nuts. Remove and keep any washers on loose bolts.
FIGURE 1: LEFT WING - DRAG FITTINGS AND WING UPPER SKIN - LOOSE FASTENER INSPECTION
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 2 March 01, 2021
55 of 105
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 56 (OCR)

REQUIREMENTS BULLETIN 757-57A0073
ALERT  ALERT
RIGHT WING
18 LOCATIONS (1
PRATT AND WHITNEY STRUT SHOWN,  2559953
ROLLS ROYCE STRUT SIMILAR
FIGURE 2: RIGHT WING - DRAG FITTINGS AND WING UPPER SKIN - LOOSE FASTENER INSPECTION
(SHEET 1 OF 2)
Original Issue: July 14, 2017
Revision 2 March 01, 2021  Export Controlled ECCN: 9E991  Copyright © Unpublished  757-57A0073 RB
Work - See page 1 for details.  56 of 105

### Page 57

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
More DataQtyIdentificationNameTaskStep
(a)18-FastenersInspect1
(c)--FastenerRemove
(b)18-FastenersInspect2
(c)--FastenerRemove
(a) Do a general visual inspection for any loose fastener at all 18 locations. A fastener is loose if any of the
following apply:
– the fastener head is protruding from the skin
– there is a discoloration adjacent to or around the fastener and cracked paint all the way around the
fastener head (if painted)
– there is a streak of dirt or oil aft of the fastener coming from the fastener hole
Refer to APPENDIX B of the service bulletin for supplemental information on doing the inspection.
(b) Do a detailed inspection for any loose fastener at all 18 locations by applying torque to the heads of the
fasteners. Apply a minimum of 30 in-lbs of torque to the fastener head. Do not secure the nut to do the
inspection. If fastener rotation occurs during the inspection, the fastener is loose.
(c) Remove and discard any loose bolts and nuts. Remove and keep any washers on loose bolts.
FIGURE 2: RIGHT WING - DRAG FITTINGS AND WING UPPER SKIN - LOOSE FASTENER INSPECTION
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 2 March 01, 2021
57 of 105
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 58 (OCR)

REQUIREMENTS BULLETIN 757-57A0073
ALERT  ALERT
LEFT WING
FWD
INBD  2552015
FIGURE 3: LEFT WING - DRAG FITTINGS AND WING UPPER SKIN - SHIM MIGRATION INSPECTION
(SHEET 1 OF 4)
Original Issue: July 14, 2017
Revision 2 March 01, 2021  Export Controlled ECCN: 9E991  Copyright © Unpublished
Work - See page 1 for details.

### Page 59 (OCR)

REQUIREMENTS BULLETIN 757-57A0073
ALERT  ALERT
INBD
2552822
FIGURE 3: LEFT WING - DRAG FITTINGS AND WING UPPER SKIN - SHIM MIGRATION INSPECTION
(SHEET 2 OF 4)
Original Issue: July 14, 2017
Revision 2 March 01, 2021  Export Controlled ECCN: 9E991  Copyright © Unpublished  757-57A0073 RB
Work - See page 1 for details.  59 of 105

### Page 60 (OCR)

REQUIREMENTS BULLETIN 757-57A0073
ALERT  ALERT
SKIN
NACELLE
A-A
FRONT SPAR
B-B  -C  2562432
FIGURE 3: LEFT WING - DRAG FITTINGS AND WING UPPER SKIN - SHIM MIGRATION INSPECTION
(SHEET 3 OF 4)
Original Issue: July 14, 2017
Revision 2 March 01, 2021  Export Controlled ECCN: 9E991  757-57A0073 RB
Copyright © Unpublished
Work - See page 1 for details.  60 of 105

The text continues at https://openairdocs.org/service-documents/boeing/757-57a0073-rb/file/19c9f832fb17.md?from=61

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
