# Boeing Alert Requirements Bulletin 757-57A0073 RB: Revision 1

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2019-0984; AD 2020-21-17 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Alert Requirements Bulletin 757-57A0073 RB](https://openairdocs.org/service-documents/boeing/757-57a0073-rb.md)
- Title as filed: RB-757-57A0073-01-- BOEING
- Pages: 103
- PDF: https://openairdocs.org/files/sha256/95/9c/959ce5aa4107897ac38853d21bcc3460eebc15dc53854d524deb9b152f78eb37
- Page: https://openairdocs.org/service-documents/boeing/757-57a0073-rb/file/959ce5aa4107

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Commercial 
Airplanes
757
Requirements Bulletin
ALERT
Number: 757-57A0073 RB
Original Issue: July 14, 2017
Revision 1: August 01, 2019
ATA System: 5720
SUBJECT: WINGS - Outer Wing - Upper Skin, Drag Fittings and Diagonal Brace Fastener and
Shim Inspections
Export of this technology is controlled under the United States Export Administration Regulations (EAR) (15
CFR 300-774). An export license may be required before it is used for development, production or use by foreign
persons from specific countries. The controller of this data has the individual responsibility to abide by all export
laws.
9E991ECCN:
BOEING PROPRIETARY, CONFIDENTIAL AND/OR TRADE SECRET
Copyright © 2017 Boeing.
Unpublished Work. All Rights Reserved.
Treatment of this document and its content is governed by contract with Boeing. Rights to use this document
are licensed on a per aircraft basis and such rights may not be transferable. For more information, contact The
Boeing Company.
Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner,
BBJ, DC-8, DC-9, DC-10, KC-10, KC-46, KDC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8, Poseidon and
Boeing liveries are all trademarks owned by The Boeing Company; and no trademark license is granted in
connection with this document unless provided in writing by Boeing.
Original Issue: July 14, 2017
757-57A0073 RBRevision 1: August 01, 2019
1 of 103
5.0

### Page 2

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 1: August 01, 2019
2 of 103
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT
BLANK PAGE

### Page 3

Table of Contents
Revision Transmittal Sheet ............................................ 5
1 . E F F E C T I V I T Y  ................................................ 7
A. Airplanes ................................................ 7
B . S p a r e s  A f f e c t e d  ............................................ 8
2. CONCURRENT REQUIREMENTS ..................................... 8
3 . C O M P L I A N C E  ................................................ 8
4. APPROVAL ................................................ 3 4
5. ACCOMPLISHMENT INSTRUCTIONS .................................. 3 5
A. General Information ......................................... 3 5
B. Work Instructions ........................................... 3 7
FIGURE 1: LEFT WING - DRAG FITTINGS AND WING UPPER SKIN - LOOSE FASTENER INSPECTION
.................................................. 5 2
FIGURE 2: RIGHT WING - DRAG FITTINGS AND WING UPPER SKIN - LOOSE  FASTENER INSPECTION
.................................................. 5 4
FIGURE 3: LEFT WING - DRAG FITTINGS AND WING UPPER SKIN - SHIM M IGRATION INSPECTION
.................................................. 5 6
FIGURE 4: RIGHT WING - DRAG FITTINGS AND WING UPPER SKIN - SHIM MIGRATION INSPECTION
.................................................. 6 0
FIGURE 5: LEFT WING - DRAG FITTINGS AND WING UPPER SKIN - FASTEN ER 1-10 OPEN-HOLE
HFEC INSPECTION ...................................... 6 4
FIGURE 6: RIGHT WING - DRAG FITTINGS AND WING UPPER SKIN - FASTE NER 1-10 OPEN-HOLE
HFEC INSPECTION ...................................... 6 6
FIGURE 7: LEFT WING - DRAG FITTINGS AND WING UPPER SKIN - LOOSE FASTENER 11-18
OPEN-HOLE HFEC INSPECTION [Group 1-9] ........................ 6 8
FIGURE 8: RIGHT WING - DRAG FITTINGS AND WING UPPER SKIN - LOOSE  FASTENER 11-18
OPEN-HOLE HFEC INSPECTION [Group 1-9] ........................ 7 0
FIGURE 9: LEFT WING- DIAGONAL BRACE AND DIAGONAL BRACE FITTINGS - GENERAL VISUAL
INSPECTION FOR CRACKS ................................. 7 2
FIGURE 10: RIGHT WING- DIAGONAL BRACE AND DIAGONAL BRACE FITTING S - GENERAL VISUAL
INSPECTION FOR CRACKS ................................. 7 5
FIGURE 11: LEFT WING - WING UPPER SKIN - DETAILED INSPECTION FOR  C R A C K S ...... 7 8
FIGURE 12: RIGHT WING - WING UPPER SKIN - DETAILED INSPECTION FO R  C R A C K S ...... 8 0
FIGURE 13: LEFT WING - DRAG FITTINGS - INBOARD SHIM BOLT TORQUE CHECK [Group 1-9] . 82
FIGURE 14: RIGHT WING - DRAG FITTINGS - INBOARD SHIM BOLT TORQUE  CHECK [Group 1-9] . 84
FIGURE 15: LEFT WING - DRAG FITTINGS - OUTBOARD SHIM BOLT TORQUE CHECK [Group 1-9] . 86
FIGURE 16: RIGHT WING - DRAG FITTINGS - OUTBOARD SHIM BOLT TORQU E CHECK [Group 1-9]
.................................................. 8 8
FIGURE 17: LEFT WING - DRAG FITTINGS - INBOARD SHIM BOLT TORQUE CHECK [Group 10-11] . 90
FIGURE 18: RIGHT WING - DRAG FITTINGS - INBOARD SHIM BOLT TORQUE  CHECK [Group 10-11]
.................................................. 9 2
FIGURE 19: LEFT WING - DRAG FITTINGS - OUTBOARD SHIM BOLT TORQUE  CHECK [Group 10-11]
.................................................. 9 4
FIGURE 20: RIGHT WING - DRAG FITTINGS - OUTBOARD SHIM BOLT TORQU E CHECK [Group 10-11]
.................................................. 9 6
FIGURE 21: LEFT WING - DRAG FITTINGS AND WING UPPER SKIN - FASTE NER 11-18 OPEN-HOLE
HFEC INSPECTION ...................................... 9 8
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 1: August 01, 2019
3 of 103
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 4

FIGURE 22: RIGHT WING - DRAG FITTINGS AND WING UPPER SKIN - FAST ENER 11-18 OPEN-HOLE
HFEC INSPECTION ..................................... 1 0 1
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 1: August 01, 2019
4 of 103
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 5

Commercial 
Airplanes
757
Requirements Bulletin
ALERT
Revision Transmittal SheetNumber: 757-57A0073 RBOriginal Issue: July 14, 2017
Revision 1: August 01, 2019
ATA System: 5720
SUBJECT: WINGS - Outer Wing - Upper Skin, Drag Fittings and Diagonal Brace Fastener and
Shim Inspections
This revision includes all pages of the requirements bulletin.
COMPLIANCE INFORMATION RELATED TO THIS REVISION
Federal Aviation Administration (FAA) Airworthiness Directive AD 2018-16-05 is related to the requirements
bulletin. The effective date of the AD 2018-16-05 is September 10, 2018.
The Federal Aviation Administration (FAA) will possibly release an additional Airworthiness Directive related to
the Requirements Bulletin 757-57A0073 RB Revision 1. The Airworthiness Directive will make the compliance
tasks and times given in Requirements Bulletin 757-57A0073 RB Revision 1 mandatory.
Effects of this Revision on airplanes on which Original Issue of this Service Bulletin was previously done:
ActionConditionGroup
Do an open-hole High Frequency
Eddy Current (HFEC) inspection at
fastener locations 11-18 for any
crack and do applicable on-condition
actions.
Airplanes on which the Original Is-
sue of this Service Bulletin was pre-
viously done.
Group 1-11:
REASON FOR REVISION
This revision is sent to add Open-Hole High Frequency Eddy Current (HFEC) inspections at fastener locations
11-18 and update the inspection interval for the general visual inspection of the diagonal brace and diagonal
brace fittings.
The data given in Information Notice 757-57A0073 IN01 is included in this revision.
These sections were changed:
– In Effectivity, Airplanes, updated the effectivity paragraph f ormat.
– In Compliance, added and updated Airworthiness Directive (AD) related information. Updated inspection
interval for the diagonal brace and diagonal brace fittings in tables 1, 2 and 9. Also updated existing
paragraphs and the group applicability table, updated Tables 1-8, and added new Tables 9-16.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 1: August 01, 2019
5 of 103

### Page 6

– In Approval of the requirements bulletin, added alternative method of compliance (AMOC) approval paragraph.
– In Accomplishment Instructions, General Information, updated t he list.
– In Accomplishment Instructions, Work Instructions, Actions Required for Compliance, updated PARTS table,
updated Tables 1-3, and added new Tables 4-7.
– In FIGURE 5 and FIGURE 6, change fastener inspection procedure .
– In FIGURE 7 and FIGURE 8, added fastener inspection procedure.
– In FIGURE 21 and FIGURE 22, added new inspection information f or fastener locations 11-18.
Vertical lines are put on the left edge of each page, except in Effectivity and format changes, to show the location
of all content changes.
Pages with no vertical lines have no changes.
REVISION HISTORY
Service BulletinService BulletinRequirement BulletinRequirement Bulletin
757-57A0073757-57A0073757-57A0073 RB757-57A0073 RB
Issue DateIssue Date
July 14, 2017Original Issue:July 14, 2017Original Issue:
August 01, 2019Revision 1:August 01, 2019Revision 1:
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 1: August 01, 2019
6 of 103
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 7

Commercial 
Airplanes
757
Requirements Bulletin
ALERT
Number: 757-57A0073 RB
Original Issue: July 14, 2017
Revision 1: August 01, 2019
ATA System: 5720
SUBJECT: WINGS - Outer Wing - Upper Skin, Drag Fittings and Diagonal Brace Fastener and
Shim Inspections
THIS DOCUMENT IS SENT TO THE OPERATORS OF RECORD OF THE AIRPLANES SHOWN IN
PARAGRAPH 1.A., EFFECTIVITY. IF AN AIRPLANE HAS BEEN LEASED OR SOLD, SEND THIS DOCUMENT
TO THE NEW OPERATOR. IF APPLICABLE SPARES HAVE BEEN SOLD, SEND THIS DOCUMENT TO THE
NEW OWNER. THIS IS AN ENHANCED REQUIRED FOR COMPLIANCE DOCUMENT. THE BOEING
PROCESSES USED TO CREATE THE SERVICE BULLETIN (SB) AND THE REQUIREMENTS BULLETIN
(RB) ENSURE THAT THE INFORMATION BETWEEN "RC START" AND "RC END" IN THE SB ARE IDENTICAL
TO THE INFORMATION IN THE SAME SECTIONS (COMPLIANCE, WORK INSTRUCTIONS…) OF THE RB
WHICH THE SB REFERS TO AS THE RELATED DOCUMENT.
1. EFFECTIVITY
A. Airplanes
This bulletin is applicable to 757-200, 757-200CB, 757-200PF, 757-300 Airplane(s), line number(s)
1-1050 in 11 Group(s). Where the effectivity is presented with hyphens between line numbers, the
airplane applicability means "through" and "inclusive", e.g. line numbers 1-9 means line numbers 1
through 9 inclusive.
DESCRIPTIONCONFIGURATIONGROUP
757-200/-200CB/-200PF Airplanes, Line Numbers 1-735 with
Rolls-Royce engines and with cold work
-1
Airplanes that have not accomplished SB 757-54-0035.1
Airplanes that have accomplished SB 757-54-0035.2
757-200/-200PF Airplanes, Line Numbers 736-802 with Rolls-Royce
engines and with cold work.
-2
757-200 Airplanes, Line Numbers 803-1009 with Rolls-Royce engines
and without cold work
-3
757-200 Airplanes, Line Numbers 1010-1050 with Rolls-Royce
engines and without cold work
-4
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 1: August 01, 2019
7 of 103

### Page 8

DESCRIPTIONCONFIGURATIONGROUP
757-200/-200PF Airplanes, Line Numbers 1-735 with Pratt and
Whitney engines and with cold work
-5
Airplanes that have not accomplished SB 757-54-0034.1
Airplanes that have accomplished SB 757-54-0034.2
757-200 Airplanes, Line Numbers 736-802 with Pratt and Whitney
engines and with cold work
-6
757-200 Airplanes, Line Numbers 803-1009 with Pratt and Whitney
engines and without cold work
-7
757-200 Airplanes, Line Numbers 1010-1050 with Pratt and Whitney
engines and without cold work
-8
757-300 Airplanes, Line Numbers 804-855 with Rolls-Royce engines
and shear-head bolts in the drag fitting and without cold work
-9
757-300 Airplanes, Line Numbers 906-1043 with Rolls-Royce engines
and tension-head bolts in the drag fitting and without cold work
-10
757-300 Airplanes, Line Numbers 906-1043 with Pratt and Whitney
engines and tension-head bolts in the drag fitting and without cold
work
-11
B. Spares Affected
None.
2. CONCURRENT REQUIREMENTS
None.
3. COMPLIANCE
Federal Aviation Administration (FAA) Airworthiness Directive AD 2018-16-05 is related to the requirements
bulletin. The effective date of AD 2018-16-05 is September 10, 2018.
The Federal Aviation Administration (FAA) will possibly release an additional Airworthiness Directive related
to the Requirements Bulletin 757-57A0073 RB Revision 1. The Airworthiness Directive will make the
compliance tasks and times given in Requirements Bulletin 757-57A0073 RB Revision 1 mandatory.
Accomplish the required action(s), based on the applicable condition(s) in Table(s) 1 through 16, in
accordance with the Accomplishment Instructions.
When more than one OPTION is given for a CONDITION, do only one of the OPTION numbers. When
more than one ACTION is given for a CONDITION or an OPTION, do all of the ACTION numbers for that
CONDITION or OPTION.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 1: August 01, 2019
8 of 103
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 9

Each Group has three tables that give the compliance for the affected airplanes. The following table shows
which compliance tables apply to each Group.
Applicable TablesGroups
Table 7, Table 9, Table 10Group 1, Configuration 1:
Table 1, Table 3, Table 11Group 1, Configuration 2:
Table 1, Table 3, Table 12Group 2:
Table 1, Table 4, Table 12Group 3-4:
Table 8, Table 9, Table 13Group 5, Configuration 1:
Table 1, Table 5, Table 14Group 5, Configuration 2:
Table 1, Table 5, Table 15Group 6:
Table 1, Table 6, Table 15Group 7-8:
Table 1, Table 6, Table 16Group 9:
Table 2, Table 6, Table 16Group 10:
Table 2, Table 6, Table 15Group 11:
Group 1, Configuration 2; Group 2-4; Group 5, Configuration 2; Group 6-9:
Table 1: Inspection for loose fasteners, skin cracking and shim migration at the upper link drag fittings
and for cracks in the diagonal brace and diagonal brace fittings
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Within 2,100
flight cycles af-
ter the Revision
1 date of Re-
quirements Bul-
letin 757-
57A0073 RB
Before 6,000 to-
tal flight cycles
ACTION 1: Do a general
visual inspection of the
diagonal brace and diago-
nal brace fittings for any
crack.
All Airplanes
-Within 3,000
flight cycles af-
ter the effective
date of AD
2018-16-05
ACTION 2: Do inspec-
tions for loose fasteners,
skin cracks and shim mi-
grations.
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair.
CONDITION 1: ANY
CRACK FOUND IN DIAG-
ONAL BRACE OR DIAGO-
NAL BRACE FITTINGS(a)
2,100 flight cycles-Repeat general visual in-
spection of the diagonal
brace and diagonal brace
fittings for any crack.
CONDITION 2: NO
CRACK FOUND IN DIAG-
ONAL BRACE OR DIAGO-
NAL BRACE FITTINGS(a)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 1: August 01, 2019
9 of 103
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 10

Group 1, Configuration 2; Group 2-4; Group 5, Configuration 2; Group 6-9:
Table 1: Inspection for loose fasteners, skin cracking and shim migration at the upper link drag fittings
and for cracks in the diagonal brace and diagonal brace fittings
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flightCONDITION 3 (ACTION
1): Install the Upper Link
and Upper Link Pins if re-
moved.
CONDITION 3: NO SHIM
MIGRATION, NO SKIN
CRACK AND NO LOOSE
FASTENER.
3,000 flight cycles-CONDITION 3 (ACTION
2): Repeat inspections for
loose fasteners, skin
cracks and shim migra-
tions.
-Before further flightDo open-hole HFEC in-
spection of fastener holes
1-10 for cracks.
CONDITION 4: ANY
LOOSE FASTENER
FOUND ON FASTENERS
1-10 (a)
-Before further flightDo open-hole HFEC in-
spection on the loose bolt
hole(s) for cracks.
CONDITION 5: ANY
LOOSE FASTENER
FOUND ON FASTENERS
11-18 (a)
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair.
CONDITION 6: MAJOR
SHIM MIGRATION
FOUND (a)
-Before further flightOPTION 1: Contact The
Boeing Company for re-
pair instructions and do
the repair.
CONDITION 7: ANY
CRACK FOUND IN THE
DRAG FITTINGS (a)
-Before further flightOPTION 2 (ACTION 1):
Replace any cracked
drag fitting with a new
part.
-Before further flightOPTION 2 (ACTION 2):
Install the Upper Link and
Upper Link Pins if re-
moved.
3,000 flight cycles-OPTION 2 (ACTION 3):
Repeat inspections for
loose fasteners, skin
cracks and shim migra-
tions.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 1: August 01, 2019
10 of 103
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 11

Group 1, Configuration 2; Group 2-4; Group 5, Configuration 2; Group 6-9:
Table 1: Inspection for loose fasteners, skin cracking and shim migration at the upper link drag fittings
and for cracks in the diagonal brace and diagonal brace fittings
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair.
CONDITION 8: ANY
CRACK FOUND IN SKIN
(a)
-Before further flightCONDITION 9 (ACTION
1): Install new or service-
able bolts, new or kept
washers, and new nuts
for fastener holes where
fasteners were removed.
CONDITION 9: NO
CRACK FOUND IN SKIN
AND DRAG FITTINGS
DURING OPEN-HOLE
HFEC INSPECTION (a)
-Before further flightCONDITION 9 (ACTION
2): Install the Upper Link
and Upper Link Pins if re-
moved.
3,000 flight cycles-CONDITION 9 (ACTION
3): Repeat inspections for
loose fasteners, skin
cracks and shim migra-
tions.
-Before further flightDo a torque check of fas-
teners on the affected
shim(s).
CONDITION 10: MINOR
SHIM MIGRATION
FOUND IN SKIN PANEL
SHIM (a)
-Before further flightCONDITION 10.1 (AC-
TION 1): Trim affected
shim to the edge of the
fitting. Apply chemical
conversion coating on the
shim and fillet seal the
edge of the drag fitting.
CONDITION 10.1: ALL
BOLTS PASSED THE
TORQUE CHECK
-Before further flightCONDITION 10.1 (AC-
TION 2): Install the Upper
Link and Upper Link Pins
if removed.
3,000 flight cycles-CONDITION 10.1 (AC-
TION 3): Repeat inspec-
tions for loose fasteners,
skin cracks and shim mi-
grations.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 1: August 01, 2019
11 of 103
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 12

Group 1, Configuration 2; Group 2-4; Group 5, Configuration 2; Group 6-9:
Table 1: Inspection for loose fasteners, skin cracking and shim migration at the upper link drag fittings
and for cracks in the diagonal brace and diagonal brace fittings
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair.
CONDITION 10.2: ANY
BOLT FAILED THE
TORQUE CHECK
-Before further flightCONDITION 11 (ACTION
1): Trim affected shim to
the edge of the fitting.
Apply chemical conver-
sion coating on the shim
and fillet seal the edge of
the drag fitting.
CONDITION 11: MINOR
SHIM MIGRATION
FOUND IN SPAR SHIM (a)
-Before further flightCONDITION 11 (ACTION
2): Install the Upper Link
and Upper Link Pins if re-
moved.
3,000 flight cycles-CONDITION 11 (ACTION
3): Repeat inspections for
loose fasteners, skin
cracks and shim migra-
tions.
(a) More than one CONDITION can be applicable on each airplane.
Group 10-11:
Table 2: Inspection for loose fasteners, skin cracking and shim migration at the upper link drag fittings
and for cracks in the diagonal brace and diagonal brace fittings
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Within 2,100
flight cycles af-
ter the Revision
1 date of Re-
quirements Bul-
letin 757-
57A0073 RB
Before 6,000 to-
tal flight cycles
ACTION 1: Do a general
visual inspection of the
diagonal brace and diago-
nal brace fittings for any
crack.
All airplanes
-Within 3,000
flight cycles af-
ter the effective
date of AD
2018-16-05
ACTION 2: Do inspec-
tions for loose fasteners,
skin cracks and shim mi-
grations.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 1: August 01, 2019
12 of 103
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 13

Group 10-11:
Table 2: Inspection for loose fasteners, skin cracking and shim migration at the upper link drag fittings
and for cracks in the diagonal brace and diagonal brace fittings
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair.
CONDITION 1: ANY
CRACK FOUND IN DIAG-
ONAL BRACE OR DIAGO-
NAL BRACE FITTINGS(a)
2,100 flight cycles-Repeat general visual in-
spection of the diagonal
brace and diagonal brace
fittings for any crack.
CONDITION 2: NO
CRACK FOUND IN DIAG-
ONAL BRACE OR DIAGO-
NAL BRACE FITTINGS(a)
-Before further flightCONDITION 3 (ACTION
1): Install the Upper Link
and Upper Link Pins if re-
moved.
CONDITION 3: NO SHIM
MIGRATION, NO SKIN
CRACK AND NO LOOSE
FASTENER.
3,000 flight cycles-CONDITION 3 (ACTION
2): Repeat inspections for
loose fasteners, skin
cracks and shim migra-
tions.
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair.
CONDITION 6: MAJOR
SHIM MIGRATION
FOUND (a)
-Before further flightOPTION 1: Contact The
Boeing Company for re-
pair instructions and do
the repair.
CONDITION 7: ANY
CRACK FOUND IN DRAG
FITTINGS (a)
-Before further flightOPTION 2 (ACTION 1):
Replace any cracked
drag fitting with a new
part.
-Before further flightOPTION 2 (ACTION 2):
Install the Upper Link and
Upper Link Pins if re-
moved.
3,000 flight cycles-OPTION 2 (ACTION 3):
Repeat inspections for
loose fasteners, skin
cracks and shim migra-
tions.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 1: August 01, 2019
13 of 103
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 14

Group 10-11:
Table 2: Inspection for loose fasteners, skin cracking and shim migration at the upper link drag fittings
and for cracks in the diagonal brace and diagonal brace fittings
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair.
CONDITION 8: ANY
CRACK FOUND IN SKIN
(a)
-Before further flightDo a torque check of fas-
teners on the affected
shim(s).
CONDITION 10: MINOR
SHIM MIGRATION
FOUND IN SKIN PANEL
SHIM (a)
-Before further flightCONDITION 10.1 (AC-
TION 1): Trim affected
shim to the edge of the
fitting. Apply chemical
conversion coating on the
shim and fillet seal the
edge of the drag fitting.
CONDITION 10.1: ALL
BOLTS PASSED THE
TORQUE CHECK
-Before further flightCONDITION 10.1 (AC-
TION 2): Install the Upper
Link and Upper Link Pins
if removed.
3,000 flight cycles-CONDITION 10.1 (AC-
TION 3): Repeat inspec-
tions for loose fasteners,
skin cracks and shim mi-
grations.
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair.
CONDITION 10.2: ANY
BOLT FAILED THE
TORQUE CHECK
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 1: August 01, 2019
14 of 103
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 15

Group 10-11:
Table 2: Inspection for loose fasteners, skin cracking and shim migration at the upper link drag fittings
and for cracks in the diagonal brace and diagonal brace fittings
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flightCONDITION 11 (ACTION
1): Trim affected shim to
the edge of the fitting.
Apply chemical conver-
sion coating on the shim
and fillet seal the edge of
the drag fitting.
CONDITION 11: MINOR
SHIM MIGRATION
FOUND IN SPAR SHIM (a)
-Before further flightCONDITION 11 (ACTION
2): Install the Upper Link
and Upper Link Pins if re-
moved.
3,000 flight cycles-CONDITION 11 (ACTION
3): Repeat inspections for
loose fasteners, skin
cracks and shim migra-
tions.
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair.
CONDITION 12: ANY
LOOSE FASTENER
FOUND (a)
(a) More than one CONDITION can be applicable on each airplane.
Group 1, Configuration 2; Group 2:
Table 3: Inspect for cracks in the wing skin and drag fittings at the upper link drag fittings (Fastener
Locations 1-10)
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Within 3,000
flight cycles af-
ter the effective
date of AD
2018-16-05
Before 23,000
total flight cycles
Do open-hole HFEC in-
spection of fastener holes
1-10 for cracks. (a)(b)
All airplanes
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 1: August 01, 2019
15 of 103
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 16

Group 1, Configuration 2; Group 2:
Table 3: Inspect for cracks in the wing skin and drag fittings at the upper link drag fittings (Fastener
Locations 1-10)
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flightOPTION 1: Contact The
Boeing Company for re-
pair instructions and do
the repair.
CONDITION 7: ANY
CRACK FOUND IN DRAG
FITTINGS (c)
-Before further flightOPTION 2 (ACTION 1):
Replace any cracked
drag fitting with a new
part.
-Before further flightOPTION 2 (ACTION 2):
Install the Upper Link and
Upper Link Pins if re-
moved.
12,000 flight cycles-OPTION 2 (ACTION 3):
Repeat open-hole HFEC
inspection of fastener
holes 1-10 for cracks.
(a)(b)
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair.
CONDITION 8: ANY
CRACK FOUND IN SKIN
(c)
-Before further flightCONDITION 9 (ACTION
1): Install new or service-
able bolts, new or kept
washers, and new nuts.
CONDITION 9: NO
CRACK FOUND IN SKIN
AND DRAG FITTINGS
DURING OPEN-HOLE
HFEC INSPECTION -Before further flightCONDITION 9 (ACTION
2): Install the Upper Link
and Upper Link Pins if re-
moved.
12,000 flight cycles-CONDITION 9 (ACTION
3): Repeat open-hole
HFEC inspection of fas-
tener holes 1-10. (a)(b)
(a) Accomplishment of an open-hole HFEC inspection of fastener holes 1-10 as a result of CONDITION 4
meets the requirements of this action.
(b) As of the Revision 1 date of 757-57A0073 RB, when this action occurs at the same time as a loose fas-
tener inspection from Table 1, the loose fastener inspection in Table 1 must be done first.
(c) More than one CONDITION can be applicable on each airplane.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 1: August 01, 2019
16 of 103
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 17

Group 3-4:
Table 4: Inspect for cracks in the wing skin and drag fittings at the upper link drag fittings (Fastener
Locations 1-10)
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Within 3,000
flight cycles af-
ter the effective
date of AD
2018-16-05
Before 12,000
total flight cycles
Do open-hole HFEC in-
spection of fastener holes
1-10 for cracks. (a)(b)
All airplanes
-Before further flightOPTION 1: Contact The
Boeing Company for re-
pair instructions and do
the repair.
CONDITION 7: ANY
CRACK FOUND IN DRAG
FITTINGS (c)
-Before further flightOPTION 2 (ACTION 1):
Replace any cracked
drag fitting with a new
part.
-Before further flightOPTION 2 (ACTION 2):
Install the Upper Link and
Upper Link Pins if re-
moved.
12,000 flight cycles-OPTION 2 (ACTION 3):
Repeat open-hole HFEC
inspection of fastener
holes 1-10. (a)(b)
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair.
CONDITION 8: ANY
CRACK FOUND IN SKIN
(c)
-Before further flightCONDITION 9 (ACTION
1): Install new or service-
able bolts, new or kept
washers, and new nuts.
CONDITION 9: NO
CRACK FOUND IN SKIN
AND DRAG FITTINGS
DURING OPEN-HOLE
HFEC INSPECTION -Before further flightCONDITION 9 (ACTION
2): Install the Upper Link
and Upper Link Pins if re-
moved.
12,000 flight cycles-CONDITION 9 (ACTION
3): Repeat open-hole
HFEC inspection of fas-
tener holes 1-10. (a)(b)
(a) Accomplishment of an open-hole HFEC inspection of fastener holes 1-10 as a result of CONDITION 4
meets the requirements of this action.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 1: August 01, 2019
17 of 103
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 18

Group 3-4:
Table 4: Inspect for cracks in the wing skin and drag fittings at the upper link drag fittings (Fastener
Locations 1-10)
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
(b) As of the Revision 1 date of 757-57A0073 RB, when this action occurs at the same time as a loose fas-
tener inspection from Table 1, the loose fastener inspection in Table 1 must be done first.
(c) More than one CONDITION can be applicable on each airplane.
Group 5, Configuration 2; Group 6:
Table 5: Inspect for cracks in the wing skin and drag fittings at the upper link drag fittings (Fastener
Locations 1-10)
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Within 3,000
flight cycles af-
ter the effective
date of AD
2018-16-05
Before 23,000
total flight cycles
Do open-hole HFEC in-
spection of fastener holes
1-10 for cracks. (a)(b)
All airplanes
-Before further flightOPTION 1: Contact The
Boeing Company for re-
pair instructions and do
the repair.
CONDITION 7: ANY
CRACK FOUND IN DRAG
FITTINGS (c)
-Before further flightOPTION 2 (ACTION 1):
Replace any cracked
drag fitting with a new
part.
-Before further flightOPTION 2 (ACTION 2):
Install the Upper Link and
Upper Link Pins if re-
moved.
6,000 flight cycles-OPTION 2 (ACTION 3):
Repeat open-hole HFEC
inspection of fastener
holes 1-10. (a)(b)
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair.
CONDITION 8: ANY
CRACK FOUND IN SKIN
(c)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 1: August 01, 2019
18 of 103
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 19

Group 5, Configuration 2; Group 6:
Table 5: Inspect for cracks in the wing skin and drag fittings at the upper link drag fittings (Fastener
Locations 1-10)
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flightCONDITION 9 (ACTION
1): Install new or service-
able bolts, new or kept
washers, and new nuts.
CONDITION 9: NO
CRACK FOUND IN SKIN
AND DRAG FITTINGS
DURING OPEN-HOLE
HFEC INSPECTION -Before further flightCONDITION 9 (ACTION
2): Install the Upper Link
and Upper Link Pins if re-
moved.
6,000 flight cycles-CONDITION 9 (ACTION
3): Repeat open-hole
HFEC inspection of fas-
tener holes 1-10. (a)(b)
(a) Accomplishment of an open-hole HFEC inspection of fastener holes 1-10 as a result of CONDITION 4
meets the requirements of this action.
(b) As of the Revision 1 date of 757-57A0073 RB, when this action occurs at the same time as a loose fas-
tener inspection from Table 1, the loose fastener inspection in Table 1 must be done first.
(c) More than one CONDITION can be applicable on each airplane.
Group 7-11:
Table 6: Inspect for cracks in the wing skin and drag fittings at the upper link drag fittings (Fastener
Locations 1-10)
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Within 3,000
flight cycles af-
ter the effective
date of AD
2018-16-05
Before 6,000 to-
tal flight cycles
Do open-hole HFEC in-
spection of fastener holes
1-10 for cracks. (a)(b)
All airplanes
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 1: August 01, 2019
19 of 103
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 20

Group 7-11:
Table 6: Inspect for cracks in the wing skin and drag fittings at the upper link drag fittings (Fastener
Locations 1-10)
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flightOPTION 1: Contact The
Boeing Company for re-
pair instructions and do
the repair.
CONDITION 7: ANY
CRACK FOUND IN DRAG
FITTINGS (c)
-Before further flightOPTION 2 (ACTION 1):
Replace any cracked
drag fitting with a new
part.
-Before further flightOPTION 2 (ACTION 2):
Install the Upper Link and
Upper Link Pins if re-
moved.
6,000 flight cycles-OPTION 2 (ACTION 3):
Repeat open-hole HFEC
inspection of fastener
holes 1-10. (a)(b)
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair.
CONDITION 8: ANY
CRACK FOUND IN SKIN
(c)
-Before further flightCONDITION 9 (ACTION
1): Install new or service-
able bolts, new or kept
washers, and new nuts.
CONDITION 9: NO
CRACK FOUND IN SKIN
AND DRAG FITTINGS
DURING OPEN-HOLE
HFEC INSPECTION -Before further flightCONDITION 9 (ACTION
2): Install the Upper Link
and Upper Link Pins if re-
moved.
6,000 flight cycles-CONDITION 9 (ACTION
3): Repeat open-hole
HFEC inspection of fas-
tener holes 1-10. (a)(b)
(a) Accomplishment of an open-hole HFEC inspection of fastener holes 1-10 as a result of CONDITION 4
meets the requirements of this action.
(b) As of the Revision 1 date of 757-57A0073 RB, when this action occurs at the same time as a loose fas-
tener inspection from Table 1 or Table 2, the loose fastener inspection in Table 1 or Table 2 must be
done first.
(c) More than one CONDITION can be applicable on each airplane.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 1: August 01, 2019
20 of 103
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 21

Group 1, Configuration 1:
Table 7: Inspect for cracks in the wing skin and drag fittings at the upper link drag fittings (Fastener
Locations 1-10)
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Within 3,000
flight cycles af-
ter the effective
date of AD
2018-16-05
Before 8,400 to-
tal flight cycles
Do open-hole HFEC in-
spection of fastener holes
1-10 for cracks. (a)(b)
All airplanes
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair.
CONDITION 7: ANY
CRACK FOUND IN DRAG
FITTINGS (c)
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair.
CONDITION 8: ANY
CRACK FOUND IN SKIN
(c)
-Before further flightCONDITION 9 (ACTION
1): Install new or service-
able bolts, new or kept
washers, and new nuts.
CONDITION 9: NO
CRACK FOUND IN SKIN
AND DRAG FITTINGS
DURING OPEN-HOLE
HFEC INSPECTION -Before further flightCONDITION 9 (ACTION
2): Install the Upper Link
and Upper Link Pins if re-
moved.
8,400 flight cycles-CONDITION 9 (ACTION
3): Repeat open-hole
HFEC inspection of fas-
tener holes 1-10. (a)(b)
(a) Accomplishment of an open-hole HFEC inspection of fastener holes 1-10 as a result of CONDITION 4
meets the requirements of this action.
(b) As of the Revision 1 date of 757-57A0073 RB, when this action occurs at the same time as a loose fas-
tener inspection from Table 9, the loose fastener inspection in Table 9 must be done first.
(c) More than one CONDITION can be applicable on each airplane.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 1: August 01, 2019
21 of 103
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 22

Group 5, Configuration 1:
Table 8: Inspect for cracks in the wing skin and drag fittings at the upper link drag fittings (Fastener
Locations 1-10)
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Within 3,000
flight cycles af-
ter the effective
date of AD
2018-16-05
Before 5,500 to-
tal flight cycles
Do open-hole HFEC in-
spection of fastener holes
1-10 for cracks. (a)(b)
All airplanes
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair.
CONDITION 7: ANY
CRACK FOUND IN DRAG
FITTINGS (c)
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair.
CONDITION 8: ANY
CRACK FOUND IN SKIN
(c)
-Before further flightCONDITION 9 (ACTION
1): Install new or service-
able bolts, new or kept
washers, and new nuts.
CONDITION 9: NO
CRACK FOUND IN SKIN
AND DRAG FITTINGS
DURING OPEN-HOLE
HFEC INSPECTION -Before further flightCONDITION 9 (ACTION
2): Install the Upper Link
and Upper Link Pins if re-
moved.
5,500 flight cycles-CONDITION 9 (ACTION
3): Repeat open-hole
HFEC inspection of fas-
tener holes 1-10. (a)(b)
(a) Accomplishment of an open-hole HFEC inspection of fastener holes 1-10 as a result of CONDITION 4
meets the requirements of this action.
(b) As of the Revision 1 date of 757-57A0073 RB, when this action occurs at the same time as a loose fas-
tener inspection from Table 9, the loose fastener inspection in Table 9 must be done first.
(c) More than one CONDITION can be applicable on each airplane.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 1: August 01, 2019
22 of 103
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 23

Group 1, 5, Configuration 1:
Table 9: Inspection for loose fasteners, skin cracking and shim migration at the upper link drag fittings
and for cracks in the diagonal brace and diagonal brace fittings
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Within 2,100
flight cycles af-
ter the Revision
1 date of Re-
quirements Bul-
letin 757-
57A0073 RB
Before 6,000 to-
tal flight cycles
ACTION 1: Do a general
visual inspection of the
diagonal brace and diago-
nal brace fittings for any
crack.
All Airplanes
-Within 3,000
flight cycles af-
ter the effective
date of AD
2018-16-05
ACTION 2: Do inspec-
tions for loose fasteners,
skin cracks and shim mi-
grations.
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair.
CONDITION 1: ANY
CRACK FOUND IN DIAG-
ONAL BRACE OR DIAGO-
NAL BRACE FITTINGS (a)
2,100 flight cycles-Repeat general visual in-
spection of the diagonal
brace and diagonal brace
fittings for any crack.
CONDITION 2: NO
CRACK FOUND IN DIAG-
ONAL BRACE OR DIAGO-
NAL BRACE FITTINGS (a)
-Before further flightCONDITION 3 (ACTION
1): Install the Upper Link
and Upper Link Pins if re-
moved.
CONDITION 3: NO SHIM
MIGRATION, NO SKIN
CRACK AND NO LOOSE
FASTENER.
3,000 flight cycles-CONDITION 3 (ACTION
2): Repeat inspections for
loose fasteners, skin
cracks and shim migra-
tions.
-Before further flightDo open-hole HFEC in-
spection of fastener holes
1-10 for cracks.
CONDITION 4: ANY
LOOSE FASTENER
FOUND ON FASTENERS
1-10 (a)
-Before further flightDo open-hole HFEC in-
spection on the loose bolt
hole(s) for cracks.
CONDITION 5: ANY
LOOSE FASTENER
FOUND ON FASTENERS
11-18 (a)
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair.
CONDITION 6: MAJOR
SHIM MIGRATION
FOUND (a)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 1: August 01, 2019
23 of 103
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 24

Group 1, 5, Configuration 1:
Table 9: Inspection for loose fasteners, skin cracking and shim migration at the upper link drag fittings
and for cracks in the diagonal brace and diagonal brace fittings
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair.
CONDITION 7: ANY
CRACK FOUND IN DRAG
FITTINGS (a)
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair.
CONDITION 8: ANY
CRACK FOUND IN SKIN
(a)
-Before further flightCONDITION 9 (ACTION
1): Install new or service-
able bolts, new or kept
washers, and new nuts
for fastener holes where
fasteners were removed.
CONDITION 9: NO
CRACK FOUND IN SKIN
AND DRAG FITTINGS
DURING OPEN-HOLE
HFEC INSPECTION
-Before further flightCONDITION 9 (ACTION
2): Install the Upper Link
and Upper Link Pins if re-
moved.
3,000 flight cycles-CONDITION 9 (ACTION
3): Repeat inspections for
loose fasteners, skin
cracks and shim migra-
tions.
-Before further flightDo a torque check of fas-
teners on the affected
shim(s).
CONDITION 10: MINOR
SHIM MIGRATION
FOUND IN SKIN PANEL
SHIM (a)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 1: August 01, 2019
24 of 103
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 25

Group 1, 5, Configuration 1:
Table 9: Inspection for loose fasteners, skin cracking and shim migration at the upper link drag fittings
and for cracks in the diagonal brace and diagonal brace fittings
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flightCONDITION 10.1 (AC-
TION 1): Trim affected
shim to the edge of the
fitting. Apply chemical
conversion coating on the
shim and fillet seal the
edge of the drag fitting.
CONDITION 10.1: ALL
BOLTS PASSED THE
TORQUE CHECK
-Before further flightCONDITION 10.1 (AC-
TION 2): Install the Upper
Link and Upper Link Pins
if removed.
3,000 flight cycles-CONDITION 10.1 (AC-
TION 3): Repeat inspec-
tions for loose fasteners,
skin cracks and shim mi-
grations.
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair.
CONDITION 10.2: ANY
BOLT FAILED THE
TORQUE CHECK
-Before further flightCONDITION 11 (ACTION
1): Trim affected shim to
the edge of the fitting.
Apply chemical conver-
sion coating on the shim
and fillet seal the edge of
the drag fitting.
CONDITION 11: MINOR
SHIM MIGRATION
FOUND IN SPAR SHIM (a)
-Before further flightCONDITION 11 (ACTION
2): Install the Upper Link
and Upper Link Pins if re-
moved.
3,000 flight cycles-CONDITION 11 (ACTION
3): Repeat inspections for
loose fasteners, skin
cracks and shim migra-
tions.
(a) More than one CONDITION can be applicable on each airplane.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 1: August 01, 2019
25 of 103
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 26

Group 1, Configuration 1:
Table 10: Inspect for cracks in the wing skin and drag fittings at the upper link drag fittings (Fastener
Locations 11-18)
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Within 3,000
flight cycles af-
ter the Revision
1 date of Re-
quirements Bul-
letin 757-
57A0073 RB
Before 8,400 to-
tal flight cycles
Do an open-hole HFEC
inspection of fastener
holes 11-18 for any crack.
(a)(b)
All airplanes
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair.
CONDITION 7: ANY
CRACK FOUND IN DRAG
FITTINGS (c)
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair.
CONDITION 8: ANY
CRACK FOUND IN SKIN
(c)
-Before further flightCONDITION 14 (ACTION
1): Install new or service-
able bolts, new or kept
washers, and new nuts.
CONDITION 14: NO
CRACK FOUND IN SKIN
AND DRAG FITTINGS.
-Before further flightCONDITION 14 (ACTION
2): Install the Upper Link
and Upper Link Pins if re-
moved.
8,400 flight cycles-CONDITION 14 (ACTION
3): Repeat open hole
HFEC inspection of fas-
tener holes 11-18 for any
crack. (a)(b)
(a) Accomplishment of an open-hole HFEC inspection of loose fastener hole(s) as a result of CONDITION
5 meets the requirements of this action for only the fastener hole(s) inspected.
(b) When this action occurs at the same time as a loose fastener inspection from Table 9, the loose fastener
inspection in Table 9 must be done first.
(c) More than one CONDITION can be applicable on each airplane.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 1: August 01, 2019
26 of 103
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 27

Group 1, Configuration 2:
Table 11: Inspect for cracks in the wing skin and drag fittings at the upper link drag fittings (Fastener
Locations 11-18)
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Within 3,000
flight cycles af-
ter the Revision
1 date of Re-
quirements Bul-
letin 757-
57A0073 RB
Before 14,000
total flight cycles
Do an open-hole HFEC
inspection of fastener
holes 11-18 for any crack.
(a)(b)
All airplanes
-Before further flightCONDITION 13 (ACTION
1): Replace any cracked
drag fitting with a new
part or contact The Boe-
ing Company for repair
instructions and do the
repair.
CONDITION 13: ANY
CRACK FOUND IN THE
DRAG FITTINGS DURING
OPEN-HOLE INSPEC-
TIONS (c)
-Before further flightCONDITION 13 (ACTION
2): Install the Upper Link
and Upper Link Pins if re-
moved.
12,000 flight cycles-CONDITION 13 (ACTION
3): Repeat open hole
HFEC inspection of fas-
tener holes 11-18 for any
crack. (a)(b)
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair.
CONDITION 8: ANY
CRACK FOUND IN SKIN
(c)
-Before further flightCONDITION 14 (ACTION
1): Install new or service-
able bolts, new or kept
washers, and new nuts.
CONDITION 14: NO
CRACK FOUND IN SKIN
AND DRAG FITTINGS
-Before further flightCONDITION 14 (ACTION
2): Install the Upper Link
and Upper Link Pins if re-
moved.
12,000 flight cycles-CONDITION 14 (ACTION
3): Repeat open hole
HFEC inspection of fas-
tener holes 11-18 for any
crack. (a)(b)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 1: August 01, 2019
27 of 103
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 28

Group 1, Configuration 2:
Table 11: Inspect for cracks in the wing skin and drag fittings at the upper link drag fittings (Fastener
Locations 11-18)
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
(a) Accomplishment of an open-hole HFEC inspection of loose fastener hole(s) as a result of CONDITION
5 meets the requirements of this action for only the fastener hole(s) inspected.
(b) When this action occurs at the same time as a loose fastener inspection from Table 1, the loose fastener
inspection in Table 1 must be done first.
(c) More than one CONDITION can be applicable on each airplane.
Group 2-4:
Table 12: Inspect for cracks in the wing skin and drag fittings at the upper link drag fittings (Fastener
Locations 11-18)
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
-Within 3,000 flight cycles after the
Revision 1 date of Requirements
Bulletin 757-57A0073 RB
Do an open-hole HFEC
inspection of fastener
holes 11-18 for any crack.
(a)(b)
All airplanes
-Before further flightCONDITION 13 (ACTION
1): Replace any cracked
drag fitting with a new
part or contact The Boe-
ing Company for repair
instructions and do the
repair.
CONDITION 13: ANY
CRACK FOUND IN THE
DRAG FITTINGS DURING
OPEN-HOLE INSPEC-
TIONS (c)
-Before further flightCONDITION 13 (ACTION
2): Install the Upper Link
and Upper Link Pins if re-
moved.
12,000 flight cycles-CONDITION 13 (ACTION
3): Repeat open-hole
HFEC inspection of fas-
tener holes 11-18 for any
crack. (a)(b)
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair.
CONDITION 8: ANY
CRACK FOUND IN SKIN
(c)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 1: August 01, 2019
28 of 103
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 29

Group 2-4:
Table 12: Inspect for cracks in the wing skin and drag fittings at the upper link drag fittings (Fastener
Locations 11-18)
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
-Before further flightCONDITION 14 (ACTION
1): Install new or service-
able bolts, new or kept
washers, and new nuts.
CONDITION 14: NO
CRACK FOUND IN SKIN
AND DRAG FITTINGS
-Before further flightCONDITION 14 (ACTION
2): Install the Upper Link
and Upper Link Pins if re-
moved.
12,000 flight cycles-CONDITION 14 (ACTION
3): Repeat open-hole
HFEC inspection of fas-
tener holes 11-18 for any
crack. (a)(b)
(a) Accomplishment of an open-hole HFEC inspection of loose fastener hole(s) as a result of CONDITION
5 meets the requirements of this action for only the fastener hole(s) inspected.
(b) When this action occurs at the same time as a loose fastener inspection from Table 1, the loose fastener
inspection in Table 1 must be done first.
(c) More than one CONDITION can be applicable on each airplane.
Group 5, Configuration 1:
Table 13: Inspect for cracks in the wing skin and drag fittings at the upper link drag fittings (Fastener
Locations 11-18)
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Within 3,000
flight cycles af-
ter the Revision
1 date of Re-
quirements Bul-
letin 757-
57A0073 RB
Before 5,500 to-
tal flight cycles
Do an open-hole HFEC
inspection of fastener
holes 11-18 for any crack.
(a)(b)
All airplanes
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair.
CONDITION 7: ANY
CRACK FOUND IN THE
DRAG FITTINGS (c)
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair.
CONDITION 8: ANY
CRACK FOUND IN SKIN
(c)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 1: August 01, 2019
29 of 103
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 30

Group 5, Configuration 1:
Table 13: Inspect for cracks in the wing skin and drag fittings at the upper link drag fittings (Fastener
Locations 11-18)
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flightCONDITION 14 (ACTION
1): Install new or service-
able bolts, new or kept
washers, and new nuts.
CONDITION 14: NO
CRACK FOUND IN SKIN
AND DRAG FITTINGS
-Before further flightCONDITION 14 (ACTION
2): Install the Upper Link
and Upper Link Pins if re-
moved.
5,500 flight cycles-CONDITION 14 (ACTION
3): Repeat open-hole
HFEC inspection of fas-
tener holes 11-18 for any
crack. (a)(b)
(a) Accomplishment of an open-hole HFEC inspection of loose fastener hole(s) as a result of CONDITION
5 meets the requirements of this action for only the fastener hole(s) inspected.
(b) When this action occurs at the same time as a loose fastener inspection from Table 9, the loose fastener
inspection in Table 9 must be done first.
(c) More than one CONDITION can be applicable on each airplane.
Group 5, Configuration 2:
Table 14: Inspect for cracks in the wing skin and drag fittings at the upper link drag fittings (Fastener
Locations 11-18)
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Within 3,000
flight cycles af-
ter the Revision
1 date of Re-
quirements Bul-
letin 757-
57A0073 RB
Before 14,000
total flight cycles
Do an open-hole HFEC
inspection of fastener
holes 11-18 for any crack.
(a)(b)
All airplanes
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 1: August 01, 2019
30 of 103
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 31

Group 5, Configuration 2:
Table 14: Inspect for cracks in the wing skin and drag fittings at the upper link drag fittings (Fastener
Locations 11-18)
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flightCONDITION 13 (ACTION
1): Replace any cracked
drag fitting with a new
part or contact The Boe-
ing Company for repair
instructions and do the
repair.
CONDITION 13: ANY
CRACK FOUND IN DRAG
FITTINGS DURING OPEN-
HOLE INSPECTIONS (c)
-Before further flightCONDITION 13 (ACTION
2): Install the Upper Link
and Upper Link Pins if re-
moved.
6,000 flight cycles-CONDITION 13 (ACTION
3): Repeat open-hole
HFEC inspection of fas-
tener holes 11-18 for any
crack. (a)(b)
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair.
CONDITION 8: ANY
CRACK FOUND IN SKIN
(c)
-Before further flightCONDITION 14 (ACTION
1): Install new or service-
able bolts, new or kept
washers, and new nuts.
CONDITION 14: NO
CRACK FOUND IN SKIN
AND DRAG FITTINGS
-Before further flightCONDITION 14 (ACTION
2): Install the Upper Link
and Upper Link Pins if re-
moved.
6,000 flight cycles-CONDITION 14 (ACTION
3): Repeat open-hole
HFEC inspection of fas-
tener holes 11-18 for any
crack. (a)(b)
(a) Accomplishment of an open-hole HFEC inspection of loose fastener hole(s) as a result of CONDITION
5 meets the requirements of this action for only the fastener hole(s) inspected.
(b) When this action occurs at the same time as a loose fastener inspection from Table 1, the loose fastener
inspection in Table 1 must be done first.
(c) More than one CONDITION can be applicable on each airplane.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 1: August 01, 2019
31 of 103
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 32

Group 6-8, 11:
Table 15: Inspect for cracks in the wing skin and drag fittings at the upper link drag fittings (Fastener
Locations 11-18)
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
-Within 3,000 flight cycles after the
Revision 1 date of Requirements
Bulletin 757-57A0073 RB
Do an open-hole HFEC
inspection of fastener
holes 11-18 for any crack.
(a)(b)
All airplanes
-Before further flightCONDITION 13 (ACTION
1): Replace any cracked
drag fitting with a new
part or contact The Boe-
ing Company for repair
instructions and do the
repair.
CONDITION 13: ANY
CRACK FOUND IN THE
DRAG FITTINGS DURING
OPEN HOLE INSPEC-
TIONS (c)
-Before further flightCONDITION 13 (ACTION
2): Install the Upper Link
and Upper Link Pins if re-
moved.
6,000 flight cycles-CONDITION 13 (ACTION
3): Repeat open-hole
HFEC inspection of fas-
tener holes 11-18 for any
crack. (a)(b)
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair.
CONDITION 8: ANY
CRACK FOUND IN SKIN
(c)
-Before further flightCONDITION 14 (ACTION
1): Install new or service-
able bolts, new or kept
washers, and new nuts.
CONDITION 14: NO
CRACK FOUND IN SKIN
AND DRAG FITTINGS
-Before further flightCONDITION 14 (ACTION
2): Install the Upper Link
and Upper Link Pins if re-
moved.
6,000 flight cycles-CONDITION 14 (ACTION
3): Repeat open-hole
HFEC inspection of fas-
tener holes 11-18 for any
crack. (a)(b)
(a) Accomplishment of an open-hole HFEC inspection of loose fastener hole(s) as a result of CONDITION
5 meets the requirements of this action for only the fastener hole(s) inspected.
(b) When this action occurs at the same time as a loose fastener inspection from Table 1 or Table 2, the
loose fastener inspection in Table 1 or Table 2 must be done first.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 1: August 01, 2019
32 of 103
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 33

Group 6-8, 11:
Table 15: Inspect for cracks in the wing skin and drag fittings at the upper link drag fittings (Fastener
Locations 11-18)
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
(c) More than one CONDITION can be applicable on each airplane.
Group 9-10:
Table 16: Inspect for cracks in the wing skin and drag fittings at the upper link drag fittings (Fastener
Locations 11-18)
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
-Within 3,000 flight cycles after the
Revision 1 date of Requirements
Bulletin 757-57A0073 RB
Do an open-hole HFEC
inspection of fastener
holes 11-18 for any crack.
(a)(b)
All airplanes
-Before further flightCONDITION 13 (ACTION
1): Replace any cracked
drag fitting with a new
part or contact The Boe-
ing Company for repair
instructions and do the
repair.
CONDITION 13: ANY
CRACK FOUND IN DRAG
FITTINGS DURING OPEN
HOLE INSPECTIONS (c)
-Before further flightCONDITION 13 (ACTION
2): Install the Upper Link
and Upper Link Pins if re-
moved.
9,000 flight cycles-CONDITION 13 (ACTION
3): Repeat open-hole
HFEC inspection of fas-
tener holes 11-18 for any
crack. (a)(b)
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair.
CONDITION 8: ANY
CRACK FOUND IN SKIN
(c)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 1: August 01, 2019
33 of 103
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 34

Group 9-10:
Table 16: Inspect for cracks in the wing skin and drag fittings at the upper link drag fittings (Fastener
Locations 11-18)
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
-Before further flightCONDITION 14 (ACTION
1): Install new or service-
able bolts, new or kept
washers, and new nuts.
CONDITION 14: NO
CRACK FOUND IN SKIN
AND DRAG FITTINGS
-Before further flightCONDITION 14 (ACTION
2): Install the Upper Link
and Upper Link Pins if re-
moved.
9,000 flight cycles-CONDITION 14 (ACTION
3): Repeat open-hole
HFEC inspection of fas-
tener holes 11-18 for any
crack. (a)(b)
(a) Accomplishment of an open-hole HFEC inspection of loose fastener hole(s) as a result of CONDITION
5 meets the requirements of this action for only the fastener hole(s) inspected.
(b) When this action occurs at the same time as a loose fastener inspection from Table 1 or Table 2, the
loose fastener inspection in Table 1 or Table 2 must be done first.
(c) More than one CONDITION can be applicable on each airplane.
4. APPROVAL
This Requirements Bulletin was examined by the Federal Aviation Administration (FAA). The changes
specified in this document comply with the applicable regulations and are FAA approved, as well as European
Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved
airplanes listed in the service bulletin effectivity. This document and its approval were based on the airplane
in its original Boeing delivery configuration or as modified by other Boeing changes.
If an airplane has a non-Boeing modification or repair that affects a component or system also affected by
this Requirements Bulletin, the operator is responsible for obtaining appropriate regulatory agency approval
before incorporating this Requirements Bulletin.
In addition the Manager of the FAA Los Angeles ACO Branch approves the actions identified in this bulletin
revision as an alternative method of compliance to paragraph (g) of AD 2018-16-05. The Manager of the
FAA Los Angeles ACO Branch also approves the use of this bulletin revision as an alternative to the original
revision of this service bulletin for compliance with paragraph (h) of AD 2018-16-05. All provisions of AD
2018-16-05 that are not specifically referenced in the above statement remain fully applicable and must be
complied with.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 1: August 01, 2019
34 of 103
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 35

5.    ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL INFORMATION
NOTE: 3. Unless shown differently, these dimensions and tolerances are  used:
– Linear dimensions are in inches
– Tolerance on linear dimensions, other than rivet and bolt edge  margins, is plus
or minus 0.03 inch
– Tolerance on rivet and bolt edge margin is plus or minus 0.05 inch
– Angular tolerance is plus or minus 2 degrees
– Hole dimensions for standard solid rivets and fasteners are in  Structural Repair
Manual (SRM) Chapter 51
– Torque Values:
— Values for structural fasteners are given in 757 Structural Repair Manual,
Chapter 51.
— Values for airframe maintenance tasks are included in Chapter 20 of 757
Aircraft Maintenance Manual (AMM).
— Values for electrical maintenance tasks are included in Chapter 20 of
Standard Wiring Practices Manual (SWPM).
— Values for engine maintenance tasks are included in Chapter 70 of 757
Aircraft Maintenance Manual (AMM).
— Non-standard torque values for maintenance tasks are included in the
applicable installation step.
4. Use the approved fastener, process and material substitutions  in accordance with
SRM Chapter 51.
5. If the length of any fastener specified in this service bulle tin does not meet installation
standards given in SRM Chapter 51, then a fastener of the same specification, or
an approved substitute, with a length which meets the installation standards given
in SRM Chapter 51 may be used. In addition, washers may be installed for fastener
grip length in accordance with SRM Chapter 51. Refer to SOPM 20-50-01 for alternate
full threaded fasteners (screws) needed for installation in this service bulletin.
6. A Detailed Inspection is defined as: An intensive examination  of a specific item,
installation, or assembly to detect damage, failure, or irregularity. Available lighting
is normally supplemented with a direct source of good lighting at an intensity deemed
appropriate. Inspection aids such as mirrors, magnifying lenses, etc. may be
necessary. Surface cleaning and elaborate procedures may be required.
7. A General Visual Inspection is defined as: A visual examinati on of an interior or
exterior area, installation or assembly to detect obvious damage, failure or irregularity.
This level of inspection is made from within touching distance unless otherwise
specified. A mirror may be necessary to enhance visual access to all exposed surfaces
in the inspection area. This level of inspection is made under normally available
lighting conditions such as daylight, hangar lighting, flashlight or drop-light and may
require removal or opening of access panels or doors. Stands, ladders or platforms
may be required to gain proximity to the area being checked.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 1: August 01, 2019
35 of 103
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 36

8. These work instructions refer to procedures included in other  Boeing documents.
When the words "refer to" are used and the operator has an accepted alternative
procedure, the accepted alternative procedure can be used. When the words "in
accordance with" are included in the instruction, the procedure in the Boeing document
must be used.
9. Boeing Service Letter 757-SL-51-022, Damage Reporting and Rep air Plan/Design
Guidelines, is an acceptable procedure to request information from Boeing for
additional structural repair instructions. The Service Letter describes what information
must be provided to Boeing before a structural repair can be provided.
12. If it is necessary to remove more parts for access, you can remove those parts. If
you can get access without removing identified parts, it is not necessary to remove
all of the identified parts. Jacking and shoring limitations must be observed.
13. Where the work instructions include installation of a kept p art, a new or serviceable
part with the same part number can be installed as an alternative to the kept part.
17. When more than one OPTION is given for a CONDITION, do only one of the OPTION
numbers. When more than one ACTION is given for a CONDITION or an OPTION,
do all of the ACTION numbers for that CONDITION or OPTION.
18. The compliance times for the actions in Work Instructions ar e in Compliance.
19. This is an Enhanced Required for Compliance document. There will be a separate
Service Bulletin (SB) and a separate Requirements Bulletin (RB). If an RB is mandated
by an Airworthiness Directive (AD), then all applicable requirements specified in the
RB must be done. For the related SB, some locations are marked RC Start and RC
End to identify the requirements that are restated from the RB. For the related SB,
the areas between RC Start and RC End, including sub-steps and any figures
identified between RC Start and RC End, must be done to comply with the AD.
Therefore, an Alternative Method of Compliance (AMOC) is required for any deviations
to steps between RC Start and RC End, including substeps and identified figures.
For the related SB, the steps not between RC Start and RC End may be deviated
from using accepted methods in accordance with the operator's maintenance or
inspection program without obtaining approval of an AMOC; this is provided that the
steps between RC Start and RC End, including sub-steps and identified figures, can
still be done as specified, and the airplane can be put back in an airworthy condition.
Figures not required for compliance are omitted from the RB.
20. This is an Enhanced Required for Compliance document. The Bo eing processes
used to create the Service Bulletin (SB) and the Requirements Bulletin (RB) ensure
that the information between "RC Start" and "RC End" in the SB are identical to the
information in the same sections (Compliance, Work Instructions...) of the RB which
the SB refers to as the related document.
21. All of the inspections given in the Work Instructions can be  done with the engine
installed or removed.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 1: August 01, 2019
36 of 103
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 37

B. WORK INSTRUCTIONS
Actions required for compliance:
1. Requirements
PARTS are identified as follows:
TitlePart
OPEN ACCESSPART 1
LOOSE FASTENER, SKIN CRACK AND SHIM MIGRA-
TION INSPECTIONS
PART 2
BOLTS 1-10 OPEN-HOLE HFEC INSPECTIONPART 3
LOOSE BOLT 11-18 OPEN-HOLE HFEC INSPECTIONPART 4
BOLT INSTALLATIONPART 5
SHIM BOLT TORQUE CHECKPART 6
SHIM TRIMMINGPART 7
BOLTS 11-18 OPEN-HOLE HFEC INSPECTIONPART 8
DRAG FITTING REPLACEMENTPART 9
OPEN ACCESS FOR GENERAL VISUAL INSPEC-
TION OF THE DIAGONAL BRACE AND DIAGONAL
BRACE FITTINGS.
PART 10
GENERAL VISUAL INSPECTION OF THE DIAGONAL
BRACE AND DIAGONAL BRACE FITTINGS FOR ANY
CRACK.
PART 11
CLOSE ACCESS FOR GENERAL VISUAL INSPEC-
TION OF THE DIAGONAL BRACE AND DIAGONAL
BRACE FITTINGS.
PART 12
CLOSE ACCESSPART 13
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 1: August 01, 2019
37 of 103
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 38

Group 1, Configuration 2; Group 2-4; Group 5, Configuration 2; Group 6-9:
Table 1 (Related to Compliance Table 1): Inspection for loose fasteners, skin cracking and shim migration
at the upper link drag fittings and for cracks in the diagonal brace and diagonal brace fittings
Refer to the listed proce-
dures in SB 757-57A0073
Original Issue or later
approved revisions as an
accepted procedure.
Method of ComplianceActionCondition
PART 10-ACTION 1: Do a general
visual inspection of the di-
agonal brace and diagonal
brace fittings for any crack.
All Airplanes
PART 11Figures 9, 10
PART 1-ACTION 2: Do inspections
for loose fasteners, skin
cracks and shim migra-
tions.
PART 2Figures 1-4, 11, 12
--Contact The Boeing Com-
pany for repair instructions
and do the repair.
CONDITION 1: ANY
CRACK FOUND IN DIAG-
ONAL BRACE OR DIAGO-
NAL BRACE FITTINGS(a)
PART 11Figures 9, 10Repeat general visual in-
spection of the diagonal
brace and diagonal brace
fittings for any crack.
CONDITION 2: NO
CRACK FOUND IN DIAG-
ONAL BRACE OR DIAGO-
NAL BRACE FITTINGS(a)
PART 13-ACTION 1: Install the Up-
per Link and Upper Link
Pins if removed.
CONDITION 3: NO SHIM
MIGRATION, NO SKIN
CRACK AND NO LOOSE
FASTENER. PART 2Figures 1-4, 11, 12ACTION 2: Repeat inspec-
tions for loose fasteners,
skin cracks and shim migra-
tions.
PART 3Figures 5, 6Do open-hole HFEC in-
spection of fastener holes
1-10 for cracks.
CONDITION 4: ANY
LOOSE FASTENER
FOUND ON FASTENERS
1-10 (a)
PART 4Figures 7, 8Do open-hole HFEC in-
spection on the loose bolt
hole(s) for cracks.
CONDITION 5: ANY
LOOSE FASTENER
FOUND ON FASTENERS
11-18 (a)
--Contact The Boeing Com-
pany for repair instructions
and do the repair.
CONDITION 6: MAJOR
SHIM MIGRATION
FOUND (a)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 1: August 01, 2019
38 of 103
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 39

Group 1, Configuration 2; Group 2-4; Group 5, Configuration 2; Group 6-9:
Table 1 (Related to Compliance Table 1): Inspection for loose fasteners, skin cracking and shim migration
at the upper link drag fittings and for cracks in the diagonal brace and diagonal brace fittings
Refer to the listed proce-
dures in SB 757-57A0073
Original Issue or later
approved revisions as an
accepted procedure.
Method of ComplianceActionCondition
--OPTION 1: Contact The
Boeing Company for repair
instructions and do the re-
pair.
CONDITION 7: ANY
CRACK FOUND IN DRAG
FITTINGS (a)
PART 9-OPTION 2 (ACTION 1):
Replace any cracked drag
fitting with a new part.
PART 13-OPTION 2 (ACTION 2):
Install the Upper Link and
Upper Link Pins if re-
moved.
PART 2Figures 1-4, 11, 12OPTION 2 (ACTION 3):
Repeat inspections for
loose fasteners, skin
cracks and shim migra-
tions.
--Contact The Boeing Com-
pany for repair instructions
and do the repair.
CONDITION 8: ANY
CRACK FOUND IN SKIN
(a)
PART 5-CONDITION 9 (ACTION
1): Install new or service-
able bolts, new or kept
washers, and new nuts.
CONDITION 9: NO
CRACK FOUND IN SKIN
AND DRAG FITTINGS
DURING OPEN-HOLE
HFEC INSPECTION (a) PART 13-CONDITION 9 (ACTION
2): Install the Upper Link
and Upper Link Pins if re-
moved.
PART 2Figures 1-4, 11, 12CONDITION 9 (ACTION
3): Repeat inspections for
loose fasteners, skin
cracks and shim migra-
tions.
PART 6Figures 13-16Do a torque check of fas-
teners on the affected
shim(s).
CONDITION 10: MINOR
SHIM MIGRATION
FOUND IN SKIN PANEL
SHIM (a)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 1: August 01, 2019
39 of 103
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 40

Group 1, Configuration 2; Group 2-4; Group 5, Configuration 2; Group 6-9:
Table 1 (Related to Compliance Table 1): Inspection for loose fasteners, skin cracking and shim migration
at the upper link drag fittings and for cracks in the diagonal brace and diagonal brace fittings
Refer to the listed proce-
dures in SB 757-57A0073
Original Issue or later
approved revisions as an
accepted procedure.
Method of ComplianceActionCondition
PART 7-CONDITION 10.1 (AC-
TION 1): Trim affected
shim to the edge of the fit-
ting. Apply chemical con-
version coating on the
shim and fillet seal the
edge of the drag fitting.
CONDITION 10.1: ALL
BOLTS PASSED THE
TORQUE CHECK
PART 13-CONDITION 10.1 (AC-
TION 2): Install the Upper
Link and Upper Link Pins
if removed.
PART 2Figures 1-4, 11, 12CONDITION 10.1 (AC-
TION 3): Repeat inspec-
tions for loose fasteners,
skin cracks and shim migra-
tions.
--Contact The Boeing Com-
pany for repair instructions
and do the repair.
CONDITION 10.2: ANY
BOLT FAILED THE
TORQUE CHECK
PART 7-CONDITION 11 (ACTION
1): Trim affected shim to
the edge of the fitting. Ap-
ply chemical conversion
coating on the shim and
fillet seal the edge of the
drag fitting.
CONDITION 11: MINOR
SHIM MIGRATION
FOUND IN SPAR SHIM
(a)
PART 13-CONDITION 11 (ACTION
2): Install the Upper Link
and Upper Link Pins if re-
moved.
PART 2Figures 1-4, 11, 12CONDITION 11 (ACTION
3): Repeat inspections for
loose fasteners, skin
cracks and shim migra-
tions.
(a) More than one CONDITION can be applicable to each airplane.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 1: August 01, 2019
40 of 103
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 41

Group 10-11:
Table 2 (Related to Compliance Table 2): Inspection for loose fasteners, skin cracking and shim migration
at the upper link drag fittings and for cracks in the diagonal brace and diagonal brace fittings
Refer to the listed proce-
dures in SB 757-57A0073
Original Issue or later
approved revisions as an
accepted procedure.
Method of ComplianceActionCondition
PART 10-ACTION 1: Do a general
visual inspection of the di-
agonal brace and diagonal
brace fittings for any crack.
All airplanes
PART 11Figures 9, 10
PART 1-ACTION 2: Do inspections
for loose fasteners, skin
cracks and shim migra-
tions.
PART 2Figures 1-4, 11, 12
--Contact The Boeing Com-
pany for repair instructions
and do the repair.
CONDITION 1: ANY
CRACK FOUND IN DIAG-
ONAL BRACE OR DIAGO-
NAL BRACE FITTINGS(a)
PART 11Figures 9, 10Repeat general visual in-
spection of the diagonal
brace and diagonal brace
fittings for any crack.
CONDITION 2: NO
CRACK FOUND IN DIAG-
ONAL BRACE OR DIAGO-
NAL BRACE FITTINGS(a)
PART 13-CONDITION 3 (ACTION
1): Install the Upper Link
and Upper Link Pins if re-
moved.
CONDITION 3: NO SHIM
MIGRATION, NO SKIN
CRACK AND NO LOOSE
FASTENER.
PART 2Figures 1-4, 11, 12CONDITION 3 (ACTION
2): Repeat inspections for
loose fasteners, skin
cracks and shim migra-
tions.
--Contact The Boeing Com-
pany for repair instructions
and do the repair.
CONDITION 6: MAJOR
SHIM MIGRATION
FOUND (a)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 1: August 01, 2019
41 of 103
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 42

Group 10-11:
Table 2 (Related to Compliance Table 2): Inspection for loose fasteners, skin cracking and shim migration
at the upper link drag fittings and for cracks in the diagonal brace and diagonal brace fittings
Refer to the listed proce-
dures in SB 757-57A0073
Original Issue or later
approved revisions as an
accepted procedure.
Method of ComplianceActionCondition
--OPTION 1: Contact The
Boeing Company for repair
instructions and do the re-
pair.
CONDITION 7: ANY
CRACK FOUND IN DRAG
FITTINGS (a)
PART 9-OPTION 2 (ACTION 1):
Replace any cracked drag
fitting with a new part.
PART 13-OPTION 2 (ACTION 2):
Install the Upper Link and
Upper Link Pins if re-
moved.
PART 2Figures 1-4, 11, 12OPTION 2 (ACTION 3):
Repeat inspections for
loose fasteners, skin
cracks and shim migra-
tions.
--Contact The Boeing Com-
pany for repair instructions
and do the repair.
CONDITION 8: ANY
CRACK FOUND IN SKIN
(a)
PART 6Figures 17-20Do a torque check of fas-
teners on the affected
shim(s).
CONDITION 10: MINOR
SHIM MIGRATION
FOUND IN SKIN PANEL
SHIM (a)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 1: August 01, 2019
42 of 103
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 43

Group 10-11:
Table 2 (Related to Compliance Table 2): Inspection for loose fasteners, skin cracking and shim migration
at the upper link drag fittings and for cracks in the diagonal brace and diagonal brace fittings
Refer to the listed proce-
dures in SB 757-57A0073
Original Issue or later
approved revisions as an
accepted procedure.
Method of ComplianceActionCondition
PART 7-CONDITION 10.1 (AC-
TION 1): Trim affected
shim to the edge of the fit-
ting. Apply chemical con-
version coating on the
shim and fillet seal the
edge of the drag fitting.
CONDITION 10.1: ALL
BOLTS PASSED THE
TORQUE CHECK
PART 13-CONDITION 10.1 (AC-
TION 2): Install the Upper
Link and Upper Link Pins
if removed.
PART 2Figures 1-4, 11, 12CONDITION 10.1 (AC-
TION 3): Repeat inspec-
tions for loose fasteners,
skin cracks and shim migra-
tions.
--Contact The Boeing Com-
pany for repair instructions
and do the repair.
CONDITION 10.2: ANY
BOLT FAILED THE
TORQUE CHECK
PART 7-CONDITION 11 (ACTION
1): Trim affected shim to
the edge of the fitting. Ap-
ply chemical conversion
coating on the shim and
fillet seal the edge of the
drag fitting.
CONDITION 11: MINOR
SHIM MIGRATION
FOUND IN SPAR SHIM
(a)
PART 13-CONDITION 11 (ACTION
2): Install the Upper Link
and Upper Link Pins if re-
moved.
PART 2Figures 1-4, 11, 12CONDITION 11 (ACTION
3): Repeat inspections for
loose fasteners, skin
cracks and shim migra-
tions.
--Contact The Boeing Com-
pany for repair instructions
and do the repair.
CONDITION 12: ANY
LOOSE FASTENER
FOUND (a)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 1: August 01, 2019
43 of 103
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 44

Group 10-11:
Table 2 (Related to Compliance Table 2): Inspection for loose fasteners, skin cracking and shim migration
at the upper link drag fittings and for cracks in the diagonal brace and diagonal brace fittings
Refer to the listed proce-
dures in SB 757-57A0073
Original Issue or later
approved revisions as an
accepted procedure.
Method of ComplianceActionCondition
(a) More than one CONDITION can apply to each airplane.
Group 1, Configuration 2; Group 2-4; Group 5, Configuration 2; Group 6-11:
Table 3 (Related to Compliance Tables 3-6): Inspect for cracks in the wing skin and drag fittings at the
upper link drag fittings (Fastener Locations 1-10)
Refer to the listed proce-
dures in SB 757-57A0073
Original Issue or later
approved revisions as an
accepted procedure.
Method of ComplianceActionCondition
PART 1-Do open-hole HFEC in-
spection of fastener holes
1-10 for cracks. (a)(b)
All airplanes
PART 3Figures 5, 6
--OPTION 1: Contact The
Boeing Company for repair
instructions and do the re-
pair.
CONDITION 7: ANY
CRACK FOUND IN DRAG
FITTINGS (c)
PART 9-OPTION 2 (ACTION 1):
Replace any cracked drag
fitting with a new part.
PART 13-OPTION 2 (ACTION 2):
Install the Upper Link and
Upper Link Pins if re-
moved.
PART 3Figures 5, 6OPTION 2 (ACTION 3):
Repeat open-hole HFEC
inspection of fastener
holes 1-10. (a)(b)
--Contact The Boeing Com-
pany for repair instructions
and do the repair.
CONDITION 8: ANY
CRACK FOUND IN SKIN
(c)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 1: August 01, 2019
44 of 103
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 45

Group 1, Configuration 2; Group 2-4; Group 5, Configuration 2; Group 6-11:
Table 3 (Related to Compliance Tables 3-6): Inspect for cracks in the wing skin and drag fittings at the
upper link drag fittings (Fastener Locations 1-10)
Refer to the listed proce-
dures in SB 757-57A0073
Original Issue or later
approved revisions as an
accepted procedure.
Method of ComplianceActionCondition
PART 5-CONDITION 9 (ACTION
1): Install new or service-
able bolts, new or kept
washers, and new nuts.
CONDITION 9: NO
CRACK FOUND IN SKIN
AND DRAG FITTINGS
DURING OPEN-HOLE
HFEC INSPECTION PART 13-CONDITION 9 (ACTION
2): Install the Upper Link
and Upper Link Pins if re-
moved.
PART 3Figures 5, 6CONDITION 9 (ACTION
3): Repeat open-hole
HFEC inspection of fasten-
er holes 1-10. (a)(b)
(a) Accomplishment of an open-hole HFEC inspection of fastener holes 1-10 as a result of CONDITION 4
meets the requirements of this action.
(b) As of the Revision 1 date of 757-57A0073 RB,when this action occurs at the same time as a loose fastener
inspection from Table 1 or Table 2, the loose fastener inspection in Table 1 or Table 2 must be done first.
(c) More than one CONDITION can apply to each airplane.
Group 1, Configuration 2; Group 2-4; Group 5, Configuration 2; Group 6-11:
Table 4 (Related to Compliance Tables 11-12 and 14-16): Inspect for cracks in the wing skin and drag
fittings at the upper link drag fittings (Fastener Locations 11-18)
Refer to the listed proce-
dures in SB 757-57A0073
Revision 1 or later ap-
proved revisions as an
accepted procedure.
Method of ComplianceActionCondition
PART 1-Do an open-hole HFEC in-
spection of fastener holes
11-18 for any crack. (a)(b)
All airplanes
PART 8Figures 21, 22
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 1: August 01, 2019
45 of 103
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 46

Group 1, Configuration 2; Group 2-4; Group 5, Configuration 2; Group 6-11:
Table 4 (Related to Compliance Tables 11-12 and 14-16): Inspect for cracks in the wing skin and drag
fittings at the upper link drag fittings (Fastener Locations 11-18)
Refer to the listed proce-
dures in SB 757-57A0073
Revision 1 or later ap-
proved revisions as an
accepted procedure.
Method of ComplianceActionCondition
PART 9-CONDITION 13 (ACTION
1): Replace any cracked
drag fitting with a new part
or contact The Boeing
Company for repair instruc-
tions and do the repair.
CONDITION 13: ANY
CRACK FOUND IN THE
DRAG FITTINGS DURING
OPEN-HOLE INSPEC-
TIONS (c)
PART 13-CONDITION 13 (ACTION
2): Install the Upper Link
and Upper Link Pins if re-
moved.
PART 8Figures 21, 22CONDITION 13 (ACTION
3): Repeat open-hole
HFEC inspection of fasten-
er holes 11-18 for any
crack. (a)(b)
--Contact The Boeing Com-
pany for repair instructions
and do the repair.
CONDITION 8: ANY
CRACK FOUND IN SKIN
(c)
PART 5-CONDITION 14 (ACTION
1): Install new or service-
able bolts, new or kept
washers, and new nuts.
CONDITION 14: NO
CRACK FOUND IN SKIN
AND DRAG FITTINGS
PART 13-CONDITION 14 (ACTION
2): Install the Upper Link
and Upper Link Pins if re-
moved.
PART 8Figures 21, 22CONDITION 14 (ACTION
3): Repeat open-hole
HFEC inspection of fasten-
er holes 11-18 for any
crack. (a)(b)
(a) Accomplishment of an open-hole HFEC inspection of loose fastener hole(s) as a result of CONDITION 5
meets the requirement of this action for only the fastener hole(s) inspected
(b) When this action occurs at the same time as a loose fastener inspection from Table 1 or Table 2, the loose
fastener inspection in Table 1 or Table 2 must be done first.
(c) More than one CONDITION can apply to each airplane.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 1: August 01, 2019
46 of 103
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 47

Group 1, 5, Configuration 1:
Table 5 (Related to Compliance Table 9): Inspection for loose fasteners, skin cracking and shim migration
at the upper link drag fittings and for cracks in the diagonal brace and diagonal brace fittings
Refer to the listed proce-
dures in SB 757-57A0073
Original Issue or later
approved revisions as an
accepted procedure.
Method of ComplianceActionCondition
PART 10-ACTION 1: Do a general
visual inspection of the di-
agonal brace and diagonal
brace fittings for any crack.
All Airplanes
PART 11Figures 9, 10
PART 1-ACTION 2: Do inspections
for loose fasteners, skin
cracks and shim migra-
tions.
PART 2Figures 1-4, 11, 12
--Contact The Boeing Com-
pany for repair instructions
and do the repair
CONDITION 1: ANY
CRACK FOUND IN DIAG-
ONAL BRACE OR DIAGO-
NAL BRACE FITTINGS (a)
PART 11Figures 9, 10Repeat general visual in-
spection of the diagonal
brace and diagonal brace
fittings for any crack.
CONDITION 2: NO
CRACK FOUND IN DIAG-
ONAL BRACE OR DIAGO-
NAL BRACE FITTINGS (a)
PART 13-CONDITION 3 (ACTION
1): Install the Upper Link
and Upper Link Pins if re-
moved.
CONDITION 3: NO SHIM
MIGRATION, NO SKIN
CRACK AND NO LOOSE
FASTENER.
PART 2Figures 1-4, 11, 12CONDITION 3 (ACTION
2): Repeat inspections for
loose fasteners, skin
cracks and shim migra-
tions.
PART 3Figures 5, 6Do open-hole HFEC in-
spection of fastener holes
1-10 for cracks.
CONDITION 4: ANY
LOOSE FASTENER
FOUND ON FASTENERS
1-10 (a)
PART 4Figures 7, 8Do open-hole HFEC in-
spection on the loose bolt
hole(s) for cracks.
CONDITION 5: ANY
LOOSE FASTENER
FOUND ON FASTENERS
11-18 (a)
--Contact The Boeing Com-
pany for repair instructions
and do the repair.
CONDITION 6: MAJOR
SHIM MIGRATION
FOUND (a)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 1: August 01, 2019
47 of 103
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 48

Group 1, 5, Configuration 1:
Table 5 (Related to Compliance Table 9): Inspection for loose fasteners, skin cracking and shim migration
at the upper link drag fittings and for cracks in the diagonal brace and diagonal brace fittings
Refer to the listed proce-
dures in SB 757-57A0073
Original Issue or later
approved revisions as an
accepted procedure.
Method of ComplianceActionCondition
--Contact The Boeing Com-
pany for repair instructions
and do the repair.
CONDITION 7: ANY
CRACK FOUND IN DRAG
FITTINGS (a)
--Contact The Boeing Com-
pany for repair instructions
and do the repair.
CONDITION 8: ANY
CRACK FOUND IN SKIN
(a)
PART 5-CONDITION 9 (ACTION
1): Install new or service-
able bolts, new or kept
washers, and new nuts.
CONDITION 9: NO
CRACK FOUND IN SKIN
AND DRAG FITTINGS
DURING OPEN-HOLE
HFEC INSPECTION (a) PART 13-CONDITION 9 (ACTION
2): Install the Upper Link
and Upper Link Pins if re-
moved.
PART 2Figures 1-4, 11, 12CONDITION 9 (ACTION
3): Repeat inspections for
loose fasteners, skin
cracks and shim migra-
tions.
PART 6Figures 13-16Do a torque check of fas-
teners on the affected
shim(s).
CONDITION 10: MINOR
SHIM MIGRATION
FOUND IN SKIN PANEL
SHIM (a)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 1: August 01, 2019
48 of 103
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 49

Group 1, 5, Configuration 1:
Table 5 (Related to Compliance Table 9): Inspection for loose fasteners, skin cracking and shim migration
at the upper link drag fittings and for cracks in the diagonal brace and diagonal brace fittings
Refer to the listed proce-
dures in SB 757-57A0073
Original Issue or later
approved revisions as an
accepted procedure.
Method of ComplianceActionCondition
PART 7-CONDITION 10.1 (AC-
TION 1): Trim affected
shim to the edge of the fit-
ting. Apply chemical con-
version coating on the
shim and fillet seal the
edge of the drag fitting.
CONDITION 10.1: ALL
BOLTS PASSED THE
TORQUE CHECK
PART 13-CONDITION 10.1 (AC-
TION 2): Install the Upper
Link and Upper Link Pins
if removed.
PART 2Figures 1-4, 11, 12CONDITION 10.1 (AC-
TION 3): Repeat inspec-
tions for loose fasteners,
skin cracks and shim migra-
tions.
--Contact The Boeing Com-
pany for repair instructions
and do the repair.
CONDITION 10.2: ANY
BOLT FAILED THE
TORQUE CHECK
PART 7-CONDITION 11 (ACTION
1): Trim affected shim to
the edge of the fitting. Ap-
ply chemical conversion
coating on the shim and
fillet seal the edge of the
drag fitting.
CONDITION 11: MINOR
SHIM MIGRATION
FOUND IN SPAR SHIM
(a)
PART 13-CONDITION 11 (ACTION
2): Install the Upper Link
and Upper Link Pins if re-
moved.
PART 2Figures 1-4, 11, 12CONDITION 11 (ACTION
3): Repeat inspections for
loose fasteners, skin
cracks and shim migra-
tions.
(a) More than one CONDITION can be applicable to each airplane.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 1: August 01, 2019
49 of 103
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 50

Group 1, 5, Configuration 1:
Table 6 (Related to Compliance Table 7-8): Inspect for cracks in the wing skin and drag fittings at the
upper link drag fittings (Fastener Locations 1-10)
Refer to the listed proce-
dures in SB 757-57A0073
Original Issue or later
approved revisions as an
accepted procedure.
Method of ComplianceActionCondition
PART 1-Do open-hole HFEC in-
spection of fastener holes
1-10 for cracks. (a)(b)
All airplanes
PART 3Figures 5, 6
--Contact The Boeing Com-
pany for repair instructions
and do the repair.
CONDITION 7 ANY
CRACK FOUND IN DRAG
FITTINGS (c)
--Contact The Boeing Com-
pany for repair instructions
and do the repair.
CONDITION 8: ANY
CRACK FOUND IN SKIN
(c)
PART 5-CONDITION 9 (ACTION
1): Install new or service-
able bolts, new or kept
washers, and new nuts.
CONDITION 9: NO
CRACK FOUND IN SKIN
AND DRAG FITTINGS
DURING OPEN-HOLE
HFEC INSPECTION PART 13-CONDITION 9 (ACTION
2): Install the Upper Link
and Upper Link Pins if re-
moved.
PART 3Figures 5, 6CONDITION 9 (ACTION
3): Repeat open-hole
HFEC inspection of fasten-
er holes 1-10. (a)(b)
(a) Accomplishment of an open-hole HFEC inspection of fastener holes 1-10 as a result of CONDITION 4
meets the requirements of this action.
(b) As of the Revision 1 date of 757-57A0073 RB, when this action occurs at the same time as a loose fastener
inspection from Table 9, the loose fastener inspection in Table 9 must be done first.
(c) More than one CONDITION can be applicable to each airplane.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 1: August 01, 2019
50 of 103
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 51

Group 1, 5, Configuration 1:
Table 7 (Related to Compliance Table 10 and Table 13): Inspect for cracks in the wing skin and drag fittings
at the upper link drag fittings (Fastener Locations 11-18)
Refer to the listed proce-
dures in SB 757-57A0073
Revision 1 or later ap-
proved revisions as an
accepted procedure.
Method of ComplianceActionCondition
PART 1-Do an open-hole HFEC in-
spection of fastener holes
11-18 for any crack. (a)(b)
All airplanes
PART 8Figures 21, 22
--Contact The Boeing Com-
pany for repair instructions
and do the repair.
CONDITION 7: ANY
CRACK FOUND IN DRAG
FITTINGS (c)
--Contact The Boeing Com-
pany for repair instructions
and do the repair.
CONDITION 8: ANY
CRACK FOUND IN SKIN
(c)
PART 5-CONDITION 14 (ACTION
1): Install new or service-
able bolts, new or kept
washers, and new nuts.
CONDITION 14: NO
CRACK FOUND IN SKIN
AND DRAG FITTINGS
PART 13-CONDITION 14 (ACTION
2): Install the Upper Link
and Upper Link Pins if re-
moved.
PART 8Figures 21, 22CONDITION 14 (ACTION
3): Repeat open-hole
HFEC inspection of fasten-
er holes 11-18 for any
crack. (a)(b)
(a) Accomplishment of an open-hole HFEC inspection of loose fastener hole(s) as a result of CONDITION 5
meets the requirement of this action for only the fastener hole(s) inspected
(b) When this action occurs at the same time as a loose fastener inspection from Table 9, the loose fastener
inspection in Table 9 must be done first.
(c) More than one CONDITION can be applicable to each airplane.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 1: August 01, 2019
51 of 103
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 52 (OCR)

REQUIREMENTS BULLETIN 757-57A0073
ALERT  ALERT
LEFT WING
12 18 LOCATIONS
PRATT AND WHITNEY STRUT SHOWN,  2559950
ROLLS ROYCE STRUT SIMILAR
FIGURE 1: LEFT WING - DRAG FITTINGS AND WING UPPER SKIN - LOOSE FASTENER INSPECTION
(SHEET 1 OF 2)
Original Issue: July 14, 2017
Revision 1 August 01, 2019  Export Controlled ECCN: 9E991 - BOEING  757-57A0073 RB
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  52 of 103

### Page 53

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
More DataQtyIdentificationNameTaskStep
(a)18-FastenersInspect1
(c)--FastenerRemove
(b)18-FastenersInspect2
(c)--FastenerRemove
(a) Do a general visual inspection for any loose fastener at all 18 locations. A fastener is loose if any of the
following apply:
– the fastener head is protruding from the skin
– there is a discoloration adjacent to or around the fastener an d cracked paint all the way around the
fastener head (if painted)
– there is a streak of dirt or oil aft of the fastener coming fr om the fastener hole
Refer to APPENDIX B of the service bulletin for supplemental information on doing the inspection.
(b) Do a detailed inspection for any loose fastener at all 18 locations by applying torque to the heads of the
fasteners. Apply a minimum of 30 in-lbs of torque to the fastener head. Do not secure the nut to do the
inspection. If fastener rotation occurs during the inspection, the fastener is loose.
(c) Remove and discard any loose bolts and nuts. Remove and keep any washers on loose bolts.
FIGURE 1: LEFT WING - DRAG FITTINGS AND WING UPPER SKIN - LOOSE FASTENER INSPECTION
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 1 August 01, 2019
53 of 103
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 54 (OCR)

REQUIREMENTS BULLETIN 757-57A0073
ALERT  ALERT
RIGHT WING
18 LOCATIONS (1
PRATT AND WHITNEY STRUT SHOWN,  2559953
ROLLS ROYCE STRUT SIMILAR
FIGURE 2: RIGHT WING - DRAG FITTINGS AND WING UPPER SKIN - LOOSE FASTENER INSPECTION
(SHEET 1 OF 2)
Original Issue: July 14, 2017
Revision 1 August 01, 2019  Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright © Unpublished  757-57A0073 RB
Work - See page 1 for details.  54 of 103

### Page 55

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
More DataQtyIdentificationNameTaskStep
(a)18-FastenersInspect1
(c)--FastenerRemove
(b)18-FastenersInspect2
(c)--FastenerRemove
(a) Do a general visual inspection for any loose fastener at all 18 locations. A fastener is loose if any of the
following apply:
– the fastener head is protruding from the skin
– there is a discoloration adjacent to or around the fastener an d cracked paint all the way around the
fastener head (if painted)
– there is a streak of dirt or oil aft of the fastener coming fr om the fastener hole
Refer to APPENDIX B of the service bulletin for supplemental information on doing the inspection.
(b) Do a detailed inspection for any loose fastener at all 18 locations by applying torque to the heads of the
fasteners. Apply a minimum of 30 in-lbs of torque to the fastener head. Do not secure the nut to do the
inspection. If fastener rotation occurs during the inspection, the fastener is loose.
(c) Remove and discard any loose bolts and nuts. Remove and keep any washers on loose bolts.
FIGURE 2: RIGHT WING - DRAG FITTINGS AND WING UPPER SKIN - LOOSE FASTENER INSPECTION
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 1 August 01, 2019
55 of 103
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 56 (OCR)

REQUIREMENTS BULLETIN 757-57A0073
ALERT  ALERT
LEFT WING
FWD
2552015
FIGURE 3: LEFT WING - DRAG FITTINGS AND WING UPPER SKIN - SHIM MIGRATION INSPECTION
(SHEET 1 OF 4)
Original Issue: July 14, 2017
Revision 1 August 01, 2019  Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.

### Page 57 (OCR)

REQUIREMENTS BULLETIN 757-57A0073
ALERT  ALERT
INBD
2552822
FIGURE 3: LEFT WING - DRAG FITTINGS AND WING UPPER SKIN - SHIM MIGRATION INSPECTION
(SHEET 2 OF 4)
Original Issue: July 14, 2017
Revision 1 August 01, 2019  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  757-57A0073 RB
Work - See page 1 for details.  • 57 of 103

### Page 58 (OCR)

REQUIREMENTS BULLETIN 757-57A0073
ALERT  ALERT
SKIN
NACELLE
A-A
FRONT SPAR
B-B  -C  2562432
FIGURE 3: LEFT WING - DRAG FITTINGS AND WING UPPER SKIN - SHIM MIGRATION INSPECTION
(SHEET 3 OF 4)
Original Issue: July 14, 2017
Revision 1 August 01, 2019  Export Controlled ECCN: 9E991 - BOEING  757-57A0073 RB
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  58 of 103

### Page 59

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
More DataQtyIdentificationNameTaskStep
(a)4-ShimsInspect1
(b)(d)4-ShimsMeasure2
(c)4-ShimsRecord
(a) Do a detailed inspection for any shim migration.
(b) Measure the migration in each direction for each shim.
(c) Add the measured migration in each direction to all previously recorded migrations in the same direction
to get the total migration for each direction, in order to determine Major or Minor Shim Migration.
(d) Major Shim Migration is defined as shim migration where one or more of the following conditions applies:
– The migrated section of the shim is greater than 0.020 inches thickness
– The total migration in any direction is greater than 0.20 inch es since the shim was installed.
Any shim migration where none of these conditions applies is Minor Shim Migration.
FIGURE 3: LEFT WING - DRAG FITTINGS AND WING UPPER SKIN - SHIM MIGRATION INSPECTION
(SHEET 4 OF 4)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RBRevision 1 August 01, 2019
59 of 103
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 60 (OCR)

REQUIREMENTS BULLETIN 757-57A0073
ALERT  ALERT
RIGHT WING
FWD
2552830
FIGURE 4: RIGHT WING - DRAG FITTINGS AND WING UPPER SKIN - SHIM MIGRATION INSPECTION
(SHEET 1 OF 4)
Original Issue: July 14, 2017
Revision 1 August 01, 2019  Export Controlled ECCN: 9E991 - BOEING  757-57A0073 RB
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  60 of 103

The text continues at https://openairdocs.org/service-documents/boeing/757-57a0073-rb/file/959ce5aa4107.md?from=61

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
