# Boeing Alert Requirements Bulletin 757-57A0073 RB: RB 757-57A0073-R00--(2)

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2018-0110; AD 2018-16-05 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Alert Requirements Bulletin 757-57A0073 RB](https://openairdocs.org/service-documents/boeing/757-57a0073-rb.md)
- Title as filed: RB 757-57A0073-R00--(2)
- Pages: 71
- PDF: https://openairdocs.org/files/sha256/e6/7b/e67b742b3c43606c761633d2e48595a662cb205aaa36b25ce3d8543672480c8b
- Page: https://openairdocs.org/service-documents/boeing/757-57a0073-rb/file/e67b742b3c43

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Commercial 
Airplanes
757
Requirements Bulletin
ALERT
Number: 757-57A0073 RB
Original Issue: July 14, 2017
ATA System: 5720
SUBJECT: WINGS - Outer Wing - Upper Skin, Drag Fittings and Diagonal Brace Fastener and
Shim Inspections
Export of this technology is controlled under the United States Export Administration Regulations (EAR) (15
CFR 300-774). An export license may be required before it is used for development, production or use by foreign
persons from specific countries. The controller of this data has the individual responsibility to abide by all export
laws.
9E991ECCN:
BOEING PROPRIETARY, CONFIDENTIAL AND/OR TRADE SECRET
Copyright © 2017 Boeing.
Unpublished Work. All Rights Reserved.
Treatment of this document and its content is governed by contract with Boeing. Rights to use this document
are licensed on a per aircraft basis and such rights may not be transferable. For more information, contact The
Boeing Company.
Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner,
BBJ, DC-8, DC-9, DC-10, KC-10, KC-46, KDC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8, Poseidon and
Boeing liveries are all trademarks owned by The Boeing Company; and no trademark license is granted in
connection with this document unless provided in writing by Boeing.
Original Issue: July 14, 2017
757-57A0073 RB
1 of 71
5.0

### Page 2

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RB
2 of 71
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT
BLANK PAGE

### Page 3

Table of Contents
1 . E F F E C T I V I T Y  ................................................ 5
A. Airplanes ................................................ 5
B . S p a r e s  A f f e c t e d  ............................................ 6
2. CONCURRENT REQUIREMENTS ..................................... 6
3 . C O M P L I A N C E  ................................................ 6
4. APPROVAL ................................................ 1 6
5. ACCOMPLISHMENT INSTRUCTIONS .................................. 1 7
A. General Information ......................................... 1 7
B. Work Instructions ........................................... 1 9
FIGURE 1: LEFT WING - DRAG FITTINGS AND WING UPPER SKIN - LOOSE FASTENER INSPECTION
.................................................. 2 6
FIGURE 2: RIGHT WING - DRAG FITTINGS AND WING UPPER SKIN - LOOSE FASTENER INSPECTION
.................................................. 2 8
FIGURE 3: LEFT WING - DRAG FITTINGS AND WING UPPER SKIN - SHIM MIGRATION INSPECTION
.................................................. 3 0
FIGURE 4: RIGHT WING - DRAG FITTINGS AND WING UPPER SKIN - SHIM MIGRATION INSPECTION
.................................................. 3 4
FIGURE 5: LEFT WING - DRAG FITTINGS AND WING UPPER SKIN - FASTENER 1-10 OPEN-HOLE
HFEC INSPECTION ...................................... 3 8
FIGURE 6: RIGHT WING - DRAG FITTINGS AND WING UPPER SKIN - FASTENER 1-10 OPEN-HOLE
HFEC INSPECTION ...................................... 4 0
FIGURE 7: LEFT WING - DRAG FITTINGS AND WING UPPER SKIN - LOOSE FASTENER 11-18
OPEN-HOLE HFEC INSPECTION [Group 1-9] ........................ 4 2
FIGURE 8: RIGHT WING - DRAG FITTINGS AND WING UPPER SKIN - LOOSE FASTENER 11-18
OPEN-HOLE HFEC INSPECTION [Group 1-9] ........................ 4 4
FIGURE 9: LEFT WING- DIAGONAL BRACE AND FITTINGS - GENERAL VISUAL INSPECTION FOR
C R A C K S............................................ 4 6
FIGURE 10: RIGHT WING- DIAGONAL BRACE AND FITTINGS - GENERAL VISUAL INSPECTION FOR
C R A C K S............................................ 4 9
FIGURE 11: LEFT WING - WING UPPER SKIN - DETAILED INSPECTION FOR CRACKS ...... 5 2
FIGURE 12: RIGHT WING - WING UPPER SKIN - DETAILED INSPECTION FOR CRACKS ...... 5 4
FIGURE 13: LEFT WING - DRAG FITTINGS - INBOARD SHIM BOLT TORQUE CHECK [Group 1-9] . 56
FIGURE 14: RIGHT WING - DRAG FITTINGS - INBOARD SHIM BOLT TORQUE CHECK [Group 1-9] . 58
FIGURE 15: LEFT WING - DRAG FITTINGS - OUTBOARD SHIM BOLT TORQUE CHECK [Group 1-9] . 60
FIGURE 16: RIGHT WING - DRAG FITTINGS - OUTBOARD SHIM BOLT TORQUE CHECK [Group 1-9]
.................................................. 6 2
FIGURE 17: LEFT WING - DRAG FITTINGS - INBOARD SHIM BOLT TORQUE CHECK [Group 10-11] . 64
FIGURE 18: RIGHT WING - DRAG FITTINGS - INBOARD SHIM BOLT TORQUE CHECK [Group 10-11]
.................................................. 6 6
FIGURE 19: LEFT WING - DRAG FITTINGS - OUTBOARD SHIM BOLT TORQUE CHECK [Group 10-11]
.................................................. 6 8
FIGURE 20: RIGHT WING - DRAG FITTINGS - OUTBOARD SHIM BOLT TORQUE CHECK [Group 10-11]
.................................................. 7 0
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RB
3 of 71
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 4

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RB
4 of 71
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT
BLANK PAGE

### Page 5

Commercial 
Airplanes
757
Requirements Bulletin
ALERT
Number: 757-57A0073 RB
Original Issue: July 14, 2017
ATA System: 5720
SUBJECT: WINGS - Outer Wing - Upper Skin, Drag Fittings and Diagonal Brace Fastener and
Shim Inspections
THIS DOCUMENT IS SENT TO THE OPERATORS OF RECORD OF THE AIRPLANES SHOWN IN
PARAGRAPH 1.A., EFFECTIVITY. IF AN AIRPLANE HAS BEEN LEASED OR SOLD, SEND THIS DOCUMENT
TO THE NEW OPERATOR. IF APPLICABLE SPARES HAVE BEEN SOLD, SEND THIS DOCUMENT TO THE
NEW OWNER. THIS IS AN ENHANCED REQUIRED FOR COMPLIANCE DOCUMENT. THE BOEING
PROCESSES USED TO CREATE THE SERVICE BULLETIN (SB) AND THE REQUIREMENTS BULLETIN
(RB) ENSURE THAT THE INFORMATION BETWEEN "RC START" AND "RC END" IN THE SB ARE IDENTICAL
TO THE INFORMATION IN THE SAME SECTIONS (COMPLIANCE, WORK INSTRUCTIONS…) OF THE RB
WHICH THE SB REFERS TO AS THE RELATED DOCUMENT.
1. EFFECTIVITY
A. Airplanes
This bulletin is applicable to all 757-200/-200CB/-200PF/-300 Airplanes, line numbers 1-1050 in 11
Groups.
DESCRIPTIONCONFIGURATIONGROUP
757-200/-200CB/-200PF Airplanes, Line Numbers 1-735 with
Rolls-Royce engines and with cold work
-1
Airplanes that have not accomplished SB 757-54-0035.1
Airplanes that have accomplished SB 757-54-0035.2
757-200/-200PF Airplanes, Line Numbers 736-802 with Rolls-Royce
engines and with cold work.
-2
757-200 Airplanes, Line Numbers 803-1009 with Rolls-Royce engines
and without cold work
-3
757-200 Airplanes, Line Numbers 1010-1050 with Rolls-Royce
engines and without cold work
-4
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RB
5 of 71

### Page 6

DESCRIPTIONCONFIGURATIONGROUP
757-200/-200PF Airplanes, Line Numbers 1-735 with Pratt and
Whitney engines and with cold work
-5
Airplanes that have not accomplished SB 757-54-0034.1
Airplanes that have accomplished SB 757-54-0034.2
757-200 Airplanes, Line Numbers 736-802 with Pratt and Whitney
engines and with cold work
-6
757-200 Airplanes, Line Numbers 803-1009 with Pratt and Whitney
engines and without cold work
-7
757-200 Airplanes, Line Numbers 1010-1050 with Pratt and Whitney
engines and without cold work
-8
757-300 Airplanes, Line Numbers 804-855 with Rolls-Royce engines
and shear-head bolts in the drag fitting and without cold work
-9
757-300 Airplanes, Line Numbers 906-1043 with Rolls-Royce engines
and tension-head bolts in the drag fitting and without cold work
-10
757-300 Airplanes, Line Numbers 906-1043 with Pratt and Whitney
engines and tension-head bolts in the drag fitting and without cold
work
-11
B. Spares Affected
None.
2. CONCURRENT REQUIREMENTS
None.
3. COMPLIANCE
The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to the
requirements bulletin. The Airworthiness Directive will make the compliance tasks and times given in the
requirements bulletin mandatory.
Accomplish the required action(s), based on the applicable condition(s) in Table(s) 1 through 8, in accordance
with the Accomplishment Instructions.
When more than one OPTION is given for a CONDITION, do only one of the OPTION numbers. When
more than one ACTION is given for a CONDITION number or an OPTION number, do all of the ACTION
numbers for that CONDITION number or OPTION number.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RB
6 of 71
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 7

Each Group has two tables that give the compliance for the affected airplanes. The following table shows
which compliance tables apply to each Group.
Applicable TablesGroups
Table 1, Table 7Group 1 Configuration 1
Table 1, Table 3Group 1 Configuration 2, Group 2
Table 1, Table 4Groups 3, 4
Table 1, Table 8Group 5 Configuration 1
Table 1, Table 5Group 5 Configuration 2, Group 6
Table 1, Table 6Groups 7, 8, 9
Table 2, Table 6Groups 10, 11
Group 1-9:
Table 1: Inspection for loose fasteners, skin cracking and shim migration at the upper link drag fittings
and for cracks in the diagonal brace and fittings
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Within 3,000
flight cycles af-
ter the original
issue date of the
requirements
bulletin
Before 6,000 to-
tal flight cycles
Do inspections for loose
fasteners, skin cracks,
shim migrations, and diag-
onal brace and fittings
cracks
All Airplanes
-Before further flightACTION 1: Install the
Upper Link and Upper
Link Pins if removed.
CONDITION 1: NO SHIM
MIGRATION, NO SKIN
CRACK, NO LOOSE FAS-
TENER, AND NO CRACK
IN DIAGONAL BRACE
AND FITTINGS FOUND
3000 flight cycles-ACTION 2: Repeat in-
spections for loose fasten-
ers, skin cracks, shim mi-
grations, and diagonal
brace and fittings cracks
-Before further flightDo open-hole HFEC in-
spection of fastener holes
1-10 for cracks
CONDITION 2: ANY
LOOSE FASTENER
FOUND ON FASTENERS
1-10 (a)
-Before further flightDo open-hole HFEC in-
spection on the loose bolt
hole(s) for cracks
CONDITION 3: ANY
LOOSE FASTENER
FOUND ON FASTENERS
11-18 (a)
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair
CONDITION 4: MAJOR
SHIM MIGRATION
FOUND (a)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RB
7 of 71
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 8

Group 1-9:
Table 1: Inspection for loose fasteners, skin cracking and shim migration at the upper link drag fittings
and for cracks in the diagonal brace and fittings
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair
CONDITION 5: ANY
CRACK FOUND IN SKIN
OR DRAG FITTINGS (a)
-Before further flightACTION 1: Install new or
serviceable bolts, new or
kept washers, and new
nuts
CONDITION 6: NO
CRACK FOUND IN SKIN
AND DRAG FITTINGS
DURING OPEN-HOLE
HFEC INSPECTION (a) -Before further flightACTION 2: Install the
Upper Link and Upper
Link Pins if removed.
3000 flight cycles-ACTION 3: Repeat in-
spections for loose fasten-
ers, skin cracks, shim mi-
grations, and diagonal
brace and fittings cracks
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair
CONDITION 7: ANY
CRACK FOUND IN DIAG-
ONAL BRACE OR FIT-
TINGS (a)
-Before further flightDo a torque check of fas-
teners on the affected
shim(s)
CONDITION 8: MINOR
SHIM MIGRATION
FOUND IN SKIN PANEL
SHIM (a)
-Before further flightACTION 1: Trim affected
shim to the edge of the
fitting. Apply chemical
conversion coating on the
shim and fillet seal the
edge of the drag fitting.
CONDITION 8.1: ALL
BOLTS PASSED THE
TORQUE CHECK
-Before further flightACTION 2: Install the
Upper Link and Upper
Link Pins if removed.
3000 flight cycles-ACTION 3: Repeat in-
spections for loose fasten-
ers, skin cracks, shim mi-
grations, and diagonal
brace and fittings cracks
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RB
8 of 71
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 9

Group 1-9:
Table 1: Inspection for loose fasteners, skin cracking and shim migration at the upper link drag fittings
and for cracks in the diagonal brace and fittings
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair
CONDITION 8.2: ANY
BOLT FAILED THE
TORQUE CHECK
-Before further flightACTION 1: Trim affected
shim to the edge of the
fitting. Apply chemical
conversion coating on the
shim and fillet seal the
edge of the drag fitting.
CONDITION 9: MINOR
SHIM MIGRATION
FOUND IN SPAR SHIM (a)
-Before further flightACTION 2: Install the
Upper Link and Upper
Link Pins if removed.
3000 flight cycles-ACTION 3: Repeat in-
spections for loose fasten-
ers, skin cracks, shim mi-
grations, and diagonal
brace and fittings cracks
(a) More than one CONDITION can be applicable on each airplane.
Group 10-11:
Table 2: Inspection for loose fasteners, skin cracking and shim migration at the upper link drag fittings
and for cracks in the diagonal brace and fittings
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Within 3,000
flight cycles af-
ter the original
issue date of the
requirements
bulletin
Before 6,000 to-
tal flight cycles
Do inspections for loose
fasteners, skin cracks,
shim migrations, and diag-
onal brace and fittings
cracks
All airplanes
-Before further flightACTION 1: Install the
Upper Link and Upper
Link Pins if removed.
CONDITION 1: NO SHIM
MIGRATION, NO SKIN
CRACK, NO LOOSE FAS-
TENER, AND NO CRACK
IN DIAGONAL BRACE
AND FITTINGS FOUND
3000 flight cycles-ACTION 2: Repeat in-
spections for loose fasten-
ers, skin cracks, shim mi-
grations, and diagonal
brace and fittings cracks
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RB
9 of 71
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 10

Group 10-11:
Table 2: Inspection for loose fasteners, skin cracking and shim migration at the upper link drag fittings
and for cracks in the diagonal brace and fittings
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair
CONDITION 4: MAJOR
SHIM MIGRATION
FOUND (a)
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair
CONDITION 5: ANY
CRACK FOUND IN SKIN
OR DRAG FITTINGS (a)
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair
CONDITION 7: ANY
CRACK FOUND IN DIAG-
ONAL BRACE OR FIT-
TINGS (a)
-Before further flightDo a torque check of fas-
teners on the affected
shim(s)
CONDITION 8: MINOR
SHIM MIGRATION
FOUND IN SKIN PANEL
SHIM (a)
-Before further flightACTION 1: Trim affected
shim to the edge of the
fitting. Apply chemical
conversion coating and
fillet seal the edge of the
drag fitting
CONDITION 8.1: ALL
BOLTS PASSED THE
TORQUE CHECK
-Before further flightACTION 2: Install the
Upper Link and Upper
Link Pins if removed.
3000 flight cycles-ACTION 3: Repeat in-
spections for loose fasten-
ers, skin cracks, shim mi-
grations, and diagonal
brace and fittings cracks
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair
CONDITION 8.2: ANY
BOLT FAILED THE
TORQUE CHECK
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RB
10 of 71
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 11

Group 10-11:
Table 2: Inspection for loose fasteners, skin cracking and shim migration at the upper link drag fittings
and for cracks in the diagonal brace and fittings
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flightACTION 1: Trim affected
shim to the edge of the
fitting. Apply chemical
conversion coating and
fillet seal the edge of the
drag fitting
CONDITION 9: MINOR
SHIM MIGRATION
FOUND IN SPAR SHIM (a)
-Before further flightACTION 2: Install the
Upper Link and Upper
Link Pins if removed.
3000 flight cycles-ACTION 3: Repeat in-
spections for loose fasten-
ers, skin cracks, shim mi-
grations, and diagonal
brace and fittings cracks
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair
CONDITION 10: ANY
LOOSE FASTENER
FOUND (a)
(a) More than one CONDITION can be applicable on each airplane.
Group 1, Configuration 2; Group 2:
Table 3: Inspect for cracks in the wing skin and drag fittings at the upper link drag fittings
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Within 3,000
flight cycles af-
ter the original
issue date of the
requirements
bulletin
Before 23,000
total flight cycles
Do open-hole HFEC in-
spection of fastener holes
1-10 for cracks (b)
All airplanes
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair
CONDITION 5: ANY
CRACK FOUND IN SKIN
OR DRAG FITTINGS
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RB
11 of 71
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 12

Group 1, Configuration 2; Group 2:
Table 3: Inspect for cracks in the wing skin and drag fittings at the upper link drag fittings
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flightACTION 1: Install new or
serviceable bolts, new or
kept washers, and new
nuts
CONDITION 6: NO
CRACK FOUND IN SKIN
AND DRAG FITTINGS
DURING OPEN-HOLE
HFEC INSPECTION -Before further flightACTION 2: Install the
Upper Link and Upper
Link Pins if removed.
12,000 flight cycles
(a)
-ACTION 3: Repeat open-
hole HFEC inspection of
fastener holes 1-10
(a) Accomplishment of an open-hole HFEC inspection of fastener holes 1-10 as a result of CONDITION 2
meets the requirements of this action.
(b) When this action occurs at the same time as a loose fastener inspection from Table 1, the loose fastener
inspection in Table 1 must be done first.
Group 3-4:
Table 4: Inspect for cracks in the wing skin and drag fittings at the upper link drag fittings
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Within 3,000
flight cycles af-
ter the original
issue date of the
requirements
bulletin
Before 12,000
total flight cycles
Do open-hole HFEC in-
spection of fastener holes
1-10 for cracks (b)
All airplanes
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair
CONDITION 5: ANY
CRACK FOUND IN SKIN
OR DRAG FITTINGS
-Before further flightACTION 1: Install new or
serviceable bolts, new or
kept washers, and new
nuts
CONDITION 6: NO
CRACK FOUND IN SKIN
AND DRAG FITTINGS
DURING OPEN-HOLE
HFEC INSPECTION -Before further flightACTION 2: Install the
Upper Link and Upper
Link Pins if removed.
12,000 flight cycles
(a)
-ACTION 3: Repeat open-
hole HFEC inspection of
fastener holes 1-10
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RB
12 of 71
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 13

Group 3-4:
Table 4: Inspect for cracks in the wing skin and drag fittings at the upper link drag fittings
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
(a) Accomplishment of an open-hole HFEC inspection of fastener holes 1-10 as a result of CONDITION 2
meets the requirements of this action.
(b) When this action occurs at the same time as a loose fastener inspection from Table 1, the loose fastener
inspection in Table 1 must be done first.
Group 5, Configuration 2; Group 6:
Table 5: Inspect for cracks in the wing skin and drag fittings at the upper link drag fittings
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Within 3,000
flight cycles af-
ter the original
issue date of the
requirements
bulletin
Before 23,000
total flight cycles
Do open-hole HFEC in-
spection of fastener holes
1-10 for cracks (b)
All airplanes
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair
CONDITION 5: ANY
CRACK FOUND IN SKIN
OR DRAG FITTINGS
-Before further flightACTION 1: Install new or
serviceable bolts, new or
kept washers, and new
nuts
CONDITION 6: NO
CRACK FOUND IN SKIN
AND DRAG FITTINGS
DURING OPEN-HOLE
HFEC INSPECTION -Before further flightACTION 2: Install the
Upper Link and Upper
Link Pins if removed.
6,000 flight cycles
(a)
-ACTION 3: Repeat open-
hole HFEC inspection of
fastener holes 1-10
(a) Accomplishment of an open-hole HFEC inspection of fastener holes 1-10 as a result of CONDITION 2
meets the requirements of this action.
(b) When this action occurs at the same time as a loose fastener inspection from Table 1, the loose fastener
inspection in Table 1 must be done first.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RB
13 of 71
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 14

Group 7-11:
Table 6: Inspect for cracks in the wing skin and drag fittings at the upper link drag fittings
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Within 3,000
flight cycles af-
ter the original
issue date of the
requirements
bulletin
Before 6,000 to-
tal flight cycles
Do open-hole HFEC in-
spection of fastener holes
1-10 for cracks (b)
All airplanes
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair
CONDITION 5: ANY
CRACK FOUND IN SKIN
OR DRAG FITTINGS
-Before further flightACTION 1: Install new or
serviceable bolts, new or
kept washers, and new
nuts.
CONDITION 6: NO
CRACK FOUND IN SKIN
AND DRAG FITTINGS
DURING OPEN-HOLE
HFEC INSPECTION -Before further flightACTION 2: Install the
Upper Link and Upper
Link Pins if removed.
6,000 flight cycles
(a)
-ACTION 3: Repeat open-
hole HFEC inspection of
fastener holes 1-10
(a) Accomplishment of an open-hole HFEC inspection of fastener holes 1-10 as a result of CONDITION 2
meets the requirements of this action.
(b) When this action occurs at the same time as a loose fastener inspection from Table 1 or Table 2, the
loose fastener inspection in Table 1 or Table 2 must be done first.
Group 1, Configuration 1:
Table 7: Inspect for cracks in the wing skin and drag fittings at the upper link drag fittings
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Within 3,000
flight cycles af-
ter the original
issue date of the
requirements
bulletin
Before 8,400 to-
tal flight cycles
Do open-hole HFEC in-
spection of fastener holes
1-10 for cracks (b)
All airplanes
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair
CONDITION 5: ANY
CRACK FOUND IN SKIN
OR DRAG FITTINGS
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RB
14 of 71
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 15

Group 1, Configuration 1:
Table 7: Inspect for cracks in the wing skin and drag fittings at the upper link drag fittings
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flightACTION 1: Install new or
serviceable bolts, new or
kept washers, and new
nuts
CONDITION 6: NO
CRACK FOUND IN SKIN
AND DRAG FITTINGS
DURING OPEN-HOLE
HFEC INSPECTION -Before further flightACTION 2: Install the
Upper Link and Upper
Link Pins if removed.
8,400 flight cycles
(a)
-ACTION 3: Repeat open-
hole HFEC inspection of
fastener holes 1-10
(a) Accomplishment of an open-hole HFEC inspection of fastener holes 1-10 as a result of CONDITION 2
meets the requirements of this action.
(b) When this action occurs at the same time as a loose fastener inspection from Table 1, the loose fastener
inspection in Table 1 must be done first.
Group 5, Configuration 1:
Table 8: Inspect for cracks in the wing skin and drag fittings at the upper link drag fittings
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Within 3,000
flight cycles af-
ter the original
issue date of the
requirements
bulletin
Before 5,500 to-
tal flight cycles
Do open-hole HFEC in-
spection of fastener holes
1-10 for cracks (b)
All airplanes
-Before further flightContact The Boeing
Company for repair in-
structions and do the re-
pair
CONDITION 5: ANY
CRACK FOUND IN SKIN
OR DRAG FITTINGS
-Before further flightACTION 1: Install new or
serviceable bolts, new or
kept washers, and new
nuts
CONDITION 6: NO
CRACK FOUND IN SKIN
AND DRAG FITTINGS
DURING OPEN-HOLE
HFEC INSPECTION -Before further flightACTION 2: Install the
Upper Link and Upper
Link Pins if removed.
5,500 flight cycles
(a)
-ACTION 3: Repeat open-
hole HFEC inspection of
fastener holes 1-10
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RB
15 of 71
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 16

Group 5, Configuration 1:
Table 8: Inspect for cracks in the wing skin and drag fittings at the upper link drag fittings
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
(a) Accomplishment of an open-hole HFEC inspection of fastener holes 1-10 as a result of CONDITION 2
meets the requirements of this action.
(b) When this action occurs at the same time as a loose fastener inspection from Table 1, the loose fastener
inspection in Table 1 must be done first.
4. APPROVAL
This Requirements Bulletin was examined by the Federal Aviation Administration (FAA). The changes
specified in this document comply with the applicable regulations and are FAA approved, as well as European
Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved
airplanes listed in the service bulletin effectivity. This document and its approval were based on the airplane
in its original Boeing delivery configuration or as modified by other Boeing changes.
If an airplane has a non-Boeing modification or repair that affects a component or system also affected by
this Requirements Bulletin, the operator is responsible for obtaining appropriate regulatory agency approval
before incorporating this Requirements Bulletin.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RB
16 of 71
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 17

5.    ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL INFORMATION
NOTE: 1. Manual titles are referred to by acronyms. Refer to Paragraph 1.J., References, for
definition of the acronyms.
2. Obey all of the warnings and cautions given in the specified manual sections.
3. Unless shown differently, these dimensions and tolerances are used:
– Linear dimensions are in inches
– Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus
or minus 0.03 inch
– Tolerance on rivet and bolt edge margin is plus or minus 0.05 inch
– Angular tolerance is plus or minus 2 degrees
– Hole dimensions for standard solid rivets and fasteners are in Structural Repair
Manual (SRM) Chapter 51
– Torque Values:
— Values for structural fasteners are given in 757 Structural Repair Manual,
Chapter 51.
— Values for airframe maintenance tasks are included in Chapter 20 of 757
Aircraft Maintenance Manual (AMM).
— Values for electrical maintenance tasks are included in Chapter 20 of
Standard Wiring Practices Manual (SWPM).
— Values for engine maintenance tasks are included in Chapter 70 of 757
Aircraft Maintenance Manual (AMM).
— Non-standard torque values for maintenance tasks are included in the
applicable installation step.
4. Use the approved fastener, process and material substitutions in accordance with
SRM Chapter 51.
5. If the length of any fastener specified in this service bulletin does not meet installation
standards given in SRM Chapter 51, then a fastener of the same specification, or
an approved substitute, with a length which meets the installation standards given
in SRM Chapter 51 may be used. In addition, washers may be installed for fastener
grip length in accordance with SRM Chapter 51. Refer to SOPM 20-50-01 for alternate
full threaded fasteners (screws) needed for installation in this service bulletin.
6. A Detailed Inspection is defined as: An intensive examination of a specific item,
installation, or assembly to detect damage, failure, or irregularity. Available lighting
is normally supplemented with a direct source of good lighting at an intensity deemed
appropriate. Inspection aids such as mirrors, magnifying lenses, etc. may be
necessary. Surface cleaning and elaborate procedures may be required.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RB
17 of 71
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 18

7. A General Visual Inspection is defined as: A visual examination of an interior or
exterior area, installation or assembly to detect obvious damage, failure or irregularity.
This level of inspection is made from within touching distance unless otherwise
specified. A mirror may be necessary to enhance visual access to all exposed surfaces
in the inspection area. This level of inspection is made under normally available
lighting conditions such as daylight, hangar lighting, flashlight or drop-light and may
require removal or opening of access panels or doors. Stands, ladders or platforms
may be required to gain proximity to the area being checked.
8. These work instructions refer to procedures included in other Boeing documents.
When the words "refer to" are used and the operator has an accepted alternative
procedure, the accepted alternative procedure can be used. When the words "in
accordance with" are included in the instruction, the procedure in the Boeing document
must be used.
9. Boeing Service Letter 757-SL-51-022, Damage Reporting and Repair Plan/Design
Guidelines, is an acceptable procedure to request information from Boeing for
additional structural repair instructions. The Service Letter describes what information
must be provided to Boeing before a structural repair can be provided.
10. Refer to APPENDIX A in the Service Bulletin for Fastener Location Numbering and
APPENDIX B in the Service Bulletin for Loose Bolt Inspection Tips.
11. The instructions in Paragraph 3.B., Work Instructions and the figures can include
operation of tools or test equipment. Boeing Engineering Tool Drawings, the Illustrated
Tool and Equipment Manual, and the Special Tool and Ground Handling Drawing
Index contain data on versions of the tools or test equipment that you can use. It is
permitted to use replaced tools. It is not permitted to use superseded tools.
12. If it is necessary to remove more parts for access, you can remove those parts. If
you can get access without removing identified parts, it is not necessary to remove
all of the identified parts. Jacking and shoring limitations must be observed.
13. Where the work instructions include installation of a kept part, a new or serviceable
part with the same part number can be installed as an alternative to the kept part.
14. This service bulletin includes functional test procedures for the systems changed by
this service bulletin. More functional tests can possibly be necessary in accordance
with standard maintenance practices because of interruption to other airplane systems.
15. Use of colors in Figures is based on guidance from the ATA e-Business Program
(ATA) iSpec 2200.
16. When more than one OPTION is given for a CONDITION, do only one of the OPTION
numbers. When more than one ACTION is given for a CONDITION number or an
OPTION number, do all of the ACTION numbers for that CONDITION number or
OPTION number.
17. The compliance times for the actions in Paragraph 3.B., WORK INSTRUCTIONS
are in Paragraph 1.E., Compliance.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RB
18 of 71
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 19

18. This is an Enhanced Required for Compliance document. There will be a separate
Service Bulletin (SB) and a separate Requirements Bulletin (RB). If an RB is mandated
by an Airworthiness Directive (AD), then all applicable requirements specified in the
RB must be done. For the related SB, some locations are marked RC Start and RC
End to identify the requirements that are restated from the RB. For the related SB,
the areas between RC Start and RC End, including sub-steps and any figures
identified between RC Start and RC End, must be done to comply with the AD.
Therefore, an Alternative Method of Compliance (AMOC) is required for any deviations
to steps between RC Start and RC End, including substeps and identified figures.
For the related SB, the steps not between RC Start and RC End may be deviated
from using accepted methods in accordance with the operator's maintenance or
inspection program without obtaining approval of an AMOC; this is provided that the
steps between RC Start and RC End, including sub-steps and identified figures, can
still be done as specified, and the airplane can be put back in an airworthy condition.
Figures not required for compliance are omitted from the RB.
19. This is an Enhanced Required for Compliance document. The Boeing processes
used to create the Service Bulletin (SB) and the Requirements Bulletin (RB) ensure
that the information between "RC Start" and "RC End" in the SB are identical to the
information in the same sections (Compliance, Work Instructions...) of the RB which
the SB refers to as the related document.
20. All of the inspections given in the Work Instructions can be done with the engine
installed or removed.
B. WORK INSTRUCTIONS
Actions required for compliance:
1. Requirements
PARTS are identified as follows:
TitlePart
OPEN ACCESSPART 1
LOOSE FASTENER, SKIN CRACK, SHIM MIGRATION
AND DIAGONAL BRACE AND FITTINGS CRACK IN-
SPECTIONS
PART 2
BOLTS 1-10 OPEN-HOLE HFEC INSPECTIONPART 3
LOOSE BOLT 11-18 OPEN-HOLE HFEC INSPECTIONPART 4
BOLT INSTALLATIONPART 5
SHIM BOLT TORQUE CHECKPART 6
SHIM TRIMMINGPART 7
CLOSE ACCESSPART 8
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RB
19 of 71
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 20

Group 1-9:
Table 1 (Related to Compliance Table 1): Inspection for loose fasteners, skin cracking and shim migration
at the upper link drag fittings and for cracks in the diagonal brace and fittings
Refer to the listed proce-
dures in SB 757-57A0073
Original Issue or later
approved revisions as an
accepted procedure.
Method of ComplianceActionCondition
PART 1-Do inspections for loose
fasteners, skin cracks,
shim migrations, and diag-
onal brace and fittings
cracks
All Airplanes
PART 2Figures 1-4, 9-12
PART 8-ACTION 1: Install the Up-
per Link and Upper Link
Pins if removed.
CONDITION 1: NO SHIM
MIGRATION, NO SKIN
CRACK, NO LOOSE FAS-
TENER, AND NO CRACK
IN DIAGONAL BRACE
AND FITTINGS FOUND
PART 2Figures 1-4, 9-12ACTION 2: Repeat inspec-
tions for loose fasteners,
skin cracks, shim migra-
tions, and diagonal brace
and fittings cracks
PART 3Figures 5, 6Do open-hole HFEC in-
spection of fastener holes
1-10 for cracks
CONDITION 2: ANY
LOOSE FASTENER
FOUND ON FASTENERS
1-10 (a)
PART 4Figures 7, 8Do open-hole HFEC in-
spection on the loose bolt
hole(s) for cracks
CONDITION 3: ANY
LOOSE FASTENER
FOUND ON FASTENERS
11-18 (a)
--Contact The Boeing Com-
pany for repair instructions
and do the repair
CONDITION 4: MAJOR
SHIM MIGRATION
FOUND (a)
--Contact The Boeing Com-
pany for repair instructions
and do the repair
CONDITION 5: ANY
CRACK FOUND IN SKIN
OR DRAG FITTINGS (a)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RB
20 of 71
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 21

Group 1-9:
Table 1 (Related to Compliance Table 1): Inspection for loose fasteners, skin cracking and shim migration
at the upper link drag fittings and for cracks in the diagonal brace and fittings
Refer to the listed proce-
dures in SB 757-57A0073
Original Issue or later
approved revisions as an
accepted procedure.
Method of ComplianceActionCondition
PART 5-ACTION 1: Install new or
serviceable bolts, new or
kept washers, and new
nuts
CONDITION 6: NO
CRACK FOUND IN SKIN
AND DRAG FITTINGS
DURING OPEN-HOLE
HFEC INSPECTION (a) PART 8-ACTION 2: Install the Up-
per Link and Upper Link
Pins if removed.
PART 2Figures 1-4, 9-12ACTION 3: Repeat inspec-
tions for loose fasteners,
skin cracks, shim migra-
tions, and diagonal brace
and fittings cracks
--Contact The Boeing Com-
pany for repair instructions
and do the repair
CONDITION 7: ANY
CRACK FOUND IN DIAG-
ONAL BRACE OR FIT-
TINGS (a)
PART 6Figures 13-16Do a torque check of fas-
teners on the affected
shim(s)
CONDITION 8: MINOR
SHIM MIGRATION
FOUND IN SKIN PANEL
SHIM (a)
PART 7-ACTION 1: Trim affected
shim to the edge of the fit-
ting. Apply chemical con-
version coating on the
shim and fillet seal the
edge of the drag fitting.
CONDITION 8.1: ALL
BOLTS PASSED THE
TORQUE CHECK
PART 8-ACTION 2: Install the Up-
per Link and Upper Link
Pins if removed.
PART 2Figures 1-4, 9-12ACTION 3: Repeat inspec-
tions for loose fasteners,
skin cracks, shim migra-
tions, and diagonal brace
and fittings cracks
--Contact The Boeing Com-
pany for repair instructions
and do the repair
CONDITION 8.2: ANY
BOLT FAILED THE
TORQUE CHECK
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RB
21 of 71
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 22

Group 1-9:
Table 1 (Related to Compliance Table 1): Inspection for loose fasteners, skin cracking and shim migration
at the upper link drag fittings and for cracks in the diagonal brace and fittings
Refer to the listed proce-
dures in SB 757-57A0073
Original Issue or later
approved revisions as an
accepted procedure.
Method of ComplianceActionCondition
PART 7-ACTION 1: Trim affected
shim to the edge of the fit-
ting. Apply chemical con-
version coating on the
shim and fillet seal the
edge of the drag fitting.
CONDITION 9: MINOR
SHIM MIGRATION
FOUND IN SPAR SHIM
(a)
PART 8-ACTION 2: Install the Up-
per Link and Upper Link
Pins if removed.
PART 2Figures 1-4, 9-12ACTION 3: Repeat inspec-
tions for loose fasteners,
skin cracks, shim migra-
tions, and diagonal brace
and fittings cracks
(a) More than one CONDITION can be applicable to each airplane.
Group 10-11:
Table 2 (Related to Compliance Table 2): Inspection for loose fasteners, skin cracking and shim migration
at the upper link drag fittings and for cracks in the diagonal brace and fittings
Refer to the listed proce-
dures in SB 757-57A0073
Original Issue or later
approved revisions as an
accepted procedure.
Method of ComplianceActionCondition
PART 1-Do inspections for loose
fasteners, skin cracks,
shim migrations, and diag-
onal brace and fittings
cracks
All airplanes
PART 2Figures 1-4, 9-12
PART 8-ACTION 1: Install the Up-
per Link and Upper Link
Pins if removed.
CONDITION 1: NO SHIM
MIGRATION, NO SKIN
CRACK, NO LOOSE FAS-
TENER, AND NO CRACK
IN DIAGONAL BRACE
AND FITTINGS FOUND
PART 2Figures 1-4, 9-12ACTION 2: Repeat inspec-
tions for loose fasteners,
skin cracks, shim migra-
tions, and diagonal brace
and fittings cracks
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RB
22 of 71
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 23

Group 10-11:
Table 2 (Related to Compliance Table 2): Inspection for loose fasteners, skin cracking and shim migration
at the upper link drag fittings and for cracks in the diagonal brace and fittings
Refer to the listed proce-
dures in SB 757-57A0073
Original Issue or later
approved revisions as an
accepted procedure.
Method of ComplianceActionCondition
--Contact The Boeing Com-
pany for repair instructions
and do the repair
CONDITION 4: MAJOR
SHIM MIGRATION
FOUND (a)
--Contact The Boeing Com-
pany for repair instructions
and do the repair
CONDITION 5: ANY
CRACK FOUND IN SKIN
OR DRAG FITTINGS (a)
--Contact The Boeing Com-
pany for repair instructions
and do the repair
CONDITION 7: ANY
CRACK FOUND IN DIAG-
ONAL BRACE OR FIT-
TINGS (a)
PART 6Figures 17-20Do a torque check of fas-
teners on the affected
shim(s)
CONDITION 8: MINOR
SHIM MIGRATION
FOUND IN SKIN PANEL
SHIM (a)
PART 7-ACTION 1: Trim affected
shim to the edge of the fit-
ting. Apply chemical con-
version coating on the
shim and fillet seal the
edge of the drag fitting.
CONDITION 8.1: ALL
BOLTS PASSED THE
TORQUE CHECK
PART 8-ACTION 2: Install the Up-
per Link and Upper Link
Pins if removed.
PART 2Figures 1-4, 9-12ACTION 3: Repeat inspec-
tions for loose fasteners,
skin cracks, shim migra-
tions, and diagonal brace
and fittings cracks
--Contact The Boeing Com-
pany for repair instructions
and do the repair
CONDITION 8.2: ANY
BOLT FAILED THE
TORQUE CHECK
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RB
23 of 71
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 24

Group 10-11:
Table 2 (Related to Compliance Table 2): Inspection for loose fasteners, skin cracking and shim migration
at the upper link drag fittings and for cracks in the diagonal brace and fittings
Refer to the listed proce-
dures in SB 757-57A0073
Original Issue or later
approved revisions as an
accepted procedure.
Method of ComplianceActionCondition
PART 7-ACTION 1: Trim affected
shim to the edge of the fit-
ting. Apply chemical con-
version coating on the
shim and fillet seal the
edge of the drag fitting.
CONDITION 9: MINOR
SHIM MIGRATION
FOUND IN SPAR SHIM
(a)
PART 8-ACTION 2: Install the Up-
per Link and Upper Link
Pins if removed.
PART 2Figures 1-4, 9-12ACTION 3: Repeat inspec-
tions for loose fasteners,
skin cracks, shim migra-
tions, and diagonal brace
and fittings cracks
--Contact The Boeing Com-
pany for repair instructions
and do the repair
CONDITION 10: ANY
LOOSE FASTENER
FOUND (a)
(a) More than one CONDITION can apply to each airplane.
Table 3 (Related to Compliance Tables 3-8): Inspect for cracks in the wing skin and drag fittings at the
upper link drag fittings
Refer to the listed proce-
dures in SB 757-57A0073
Original Issue or later
approved revisions as an
accepted procedure.
Method of ComplianceActionCondition
PART 1-Do open-hole HFEC in-
spection of fastener holes
1-10 for cracks
All airplanes
PART 3Figures 5, 6
--Contact The Boeing Com-
pany for repair instructions
and do the repair
CONDITION 5: ANY
CRACK FOUND IN SKIN
OR DRAG FITTINGS
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RB
24 of 71
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 25

Table 3 (Related to Compliance Tables 3-8): Inspect for cracks in the wing skin and drag fittings at the
upper link drag fittings
Refer to the listed proce-
dures in SB 757-57A0073
Original Issue or later
approved revisions as an
accepted procedure.
Method of ComplianceActionCondition
PART 5-ACTION 1: Install new or
serviceable bolts, new or
kept washers, and new
nuts
CONDITION 6: NO
CRACK FOUND IN SKIN
AND DRAG FITTINGS
DURING OPEN-HOLE
HFEC INSPECTION PART 8-ACTION 2: Install the Up-
per Link and Upper Link
Pins if removed.
PART 3Figures 5, 6ACTION 3: Repeat open-
hole HFEC inspection of
fastener holes 1-10
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RB
25 of 71
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 26 (OCR)

REQUIREMENTS BULLETIN 757-57A0073
ALERT  ALERT
LEFT WING
12 18 LOCATIONS
PRATT AND WHITNEY STRUT SHOWN,  2559950
ROLLS ROYCE STRUT SIMILAR
FIGURE 1: LEFT WING - DRAG FITTINGS AND WING UPPER SKIN - LOOSE FASTENER INSPECTION
(SHEET 1 OF 2)
Original Issue: July 14, 2017
Export Controlled ECCN: 9E991 - BOEING  757-57A0073 RB
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  26 of 71

### Page 27

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
More DataQtyIdentificationNameTaskStep
(a)18-FastenersInspect1
(c)--FastenerRemove
(b)18-FastenersInspect2
(c)--FastenerRemove
(a) Do a general visual inspection for any loose fastener at all 18 locations. A fastener is loose if any of the
following apply:
– the fastener head is protruding from the skin
– there is a discoloration adjacent to or around the fastener and cracked paint all the way around the
fastener head (if painted)
– there is a streak of dirt or oil aft of the fastener coming from the fastener hole
Refer to APPENDIX B of the service bulletin for supplemental information on doing the inspection.
(b) Do a special detailed inspection for any loose fastener at all 18 locations by applying torque to the heads
of the fasteners. Apply a minimum of 30 in-lbs of torque to the fastener head. Do not secure the nut to
do the inspection. If fastener rotation occurs during the inspection, the fastener is loose.
(c) Remove and discard any loose bolts and nuts. Remove and keep any washers on loose bolts.
FIGURE 1: LEFT WING - DRAG FITTINGS AND WING UPPER SKIN - LOOSE FASTENER INSPECTION
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RB
27 of 71
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 28 (OCR)

REQUIREMENTS BULLETIN 757-57A0073
ALERT  ALERT
RIGHT WING
18 LOCATIONS (1
PRATT AND WHITNEY STRUT SHOWN,  2559953
ROLLS ROYCE STRUT SIMILAR
FIGURE 2: RIGHT WING - DRAG FITTINGS AND WING UPPER SKIN - LOOSE FASTENER INSPECTION
(SHEET 1 OF 2)
Original Issue: July 14, 2017
Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright © Unpublished  757-57A0073 RB
Work - See page 1 for details.  28 of 71

### Page 29

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
More DataQtyIdentificationNameTaskStep
(a)18-FastenersInspect1
(c)--FastenerRemove
(b)18-FastenersInspect2
(c)--FastenerRemove
(a) Do a general visual inspection for any loose fastener at all 18 locations. A fastener is loose if any of the
following apply:
– the fastener head is protruding from the skin
– there is a discoloration adjacent to or around the fastener and cracked paint all the way around the
fastener head (if painted)
– there is a streak of dirt or oil aft of the fastener coming from the fastener hole
Refer to APPENDIX B of the service bulletin for supplemental information on doing the inspection.
(b) Do a special detailed inspection for any loose fastener at all 18 locations by applying torque to the heads
of the fasteners. Apply a minimum of 30 in-lbs of torque to the fastener head. Do not secure the nut to
do the inspection. If fastener rotation occurs during the inspection, the fastener is loose.
(c) Remove and discard any loose bolts and nuts. Remove and keep any washers on loose bolts.
FIGURE 2: RIGHT WING - DRAG FITTINGS AND WING UPPER SKIN - LOOSE FASTENER INSPECTION
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RB
29 of 71
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 30 (OCR)

REQUIREMENTS BULLETIN 757-57A0073
ALERT  ALERT
LEFT WING
FWD
INBD  2552015
FIGURE 3: LEFT WING - DRAG FITTINGS AND WING UPPER SKIN - SHIM MIGRATION INSPECTION
(SHEET 1 OF 4)
Original Issue: July 14, 2017
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  LL 1O DE

### Page 31 (OCR)

REQUIREMENTS BULLETIN 757-57A0073
ALERT  ALERT
INBD
2552822
FIGURE 3: LEFT WING - DRAG FITTINGS AND WING UPPER SKIN - SHIM MIGRATION INSPECTION
(SHEET 2 OF 4)
Original Issue: July 14, 2017
PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  T01-5/A0073 RB
Work - See page 1 for details.  31 of 71

### Page 32 (OCR)

REQUIREMENTS BULLETIN 757-57A0073
ALERT  ALERT
SKIN
NACELLE
A-A
FRONT SPAR
B-B  :- C  2562432
FIGURE 3: LEFT WING - DRAG FITTINGS AND WING UPPER SKIN - SHIM MIGRATION INSPECTION
(SHEET 3 OF 4)
Original Issue: July 14, 2017
Export Controlled ECCN: 9E991 - BOEING  757-57A0073 RB
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  32 of 71

### Page 33

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
More DataQtyIdentificationNameTaskStep
(a)4-ShimsInspect1
(b)(d)4-ShimsMeasure2
(c)4-ShimsRecord
(a) Do a detailed inspection for any shim migration.
(b) Measure the migration in each direction for each shim.
(c) Add the measured migration in each direction to all previously recorded migrations in the same direction
to get the total migration for each direction, in order to determine Major or Minor Shim Migration.
(d) Major Shim Migration is defined as shim migration where one or more of the following conditions applies:
– The migrated section of the shim is greater than 0.020 inches thickness
– The total migration in any direction is greater than 0.20 inches since the shim was installed.
Any shim migration where none of these conditions applies is Minor Shim Migration.
FIGURE 3: LEFT WING - DRAG FITTINGS AND WING UPPER SKIN - SHIM MIGRATION INSPECTION
(SHEET 4 OF 4)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RB
33 of 71
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 34 (OCR)

REQUIREMENTS BULLETIN 757-57A0073
ALERT  ALERT
RIGHT WING
FWD
2552830
FIGURE 4: RIGHT WING - DRAG FITTINGS AND WING UPPER SKIN - SHIM MIGRATION INSPECTION
(SHEET 1 OF 4)
Original Issue: July 14, 2017
Export Controlled ECCN: 9E991 - BOEING  757-57A0073 RB
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  34 of 71

### Page 35 (OCR)

REQUIREMENTS BULLETIN 757-57A0073
ALERT  ALERT
B
INBD
2552831
FIGURE 4: RIGHT WING - DRAG FITTINGS AND WING UPPER SKIN - SHIM MIGRATION INSPECTION
(SHEET 2 OF 4)
Original Issue: July 14, 2017
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  35 of 71

### Page 36 (OCR)

REQUIREMENTS BULLETIN 757-57A0073
ALERT  ALERT
SKIN
NACELLE
A-A  FWD
FRONT SPAR
NBD  INBD
B-B  2562477
FIGURE 4: RIGHT WING - DRAG FITTINGS AND WING UPPER SKIN - SHIM MIGRATION INSPECTION
(SHEET 3 OF 4)
Original Issue: July 14, 2017
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  LLO 9E

### Page 37

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
More DataQtyIdentificationNameTaskStep
(a)4-ShimsInspect1
(b)(d)4-ShimsMeasure2
(c)4-ShimsRecord
(a) Do a detailed inspection for any shim migration.
(b) Measure the migration in each indicated direction.
(c) Add the measured migration in each direction to all previously recorded migrations in the same direction
to get the total migration for each direction, in order to determine Major or Minor Shim Migration.
(d) Major Shim Migration is defined as shim migration where one or more of the following conditions applies:
– The migrated section of the shim is greater than 0.020 inches thickness
– The total migration in any direction is greater than 0.20 inches since the shim was installed.
Any shim migration where none of these conditions applies is Minor Shim Migration.
FIGURE 4: RIGHT WING - DRAG FITTINGS AND WING UPPER SKIN - SHIM MIGRATION INSPECTION
(SHEET 4 OF 4)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RB
37 of 71
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 38 (OCR)

REQUIREMENTS BULLETIN 757-57A0073
ALERT  ALERT
LEFT WING
PRATT AND WHITNEY STRUT SHOWN,
ROLLS ROYCE STRUT SIMILAR
The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
FIGURE 5: LEFT WING - DRAG FITTINGS AND WING UPPER SKIN - FASTENER 1-10 OPEN-HOLE HFEC
INSPECTION
(SHEET 1 OF 2)
Original Issue: July 14, 2017
Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright © Unpublished  757-57A0073 RB
Work - See page 1 for details.  38 of 71

### Page 39

More DataQtyIdentificationNameTaskStep
(a)10-Fastener HolesInspect1
(b)10-FastenerInspect2
(a) Do an open-hole HFEC inspection for any crack in accordance with 757 NDT Manual Part 6, 51-00-16.
NOTE: Use the steps in 757 NDT Manual Part 6, 51-00-16 Paragraph 6 to confirm crack indication(s).
Discrepancies in shims can cause false positive crack indications. If an indication can be confirmed to be
at the same depth and radial position as the discrepancy location, the fastener hole can be accepted. A
discrepancy is defined as a cut or rip in the shim, a shim that has migrated past the edge of the hole, or
a gap caused by shim migration outward.
(b) Do a dye-penetrant inspection, Type 1, Sensitivity 2, for any crack in the fillet between head and shank
on the removed fasteners. Refer to SOPM 20-20-02 as an accepted procedure. Discard any fasteners
that shows any crack indication. A fastener with no crack indications is considered serviceable.
FIGURE 5: LEFT WING - DRAG FITTINGS AND WING UPPER SKIN - FASTENER 1-10 OPEN-HOLE HFEC
INSPECTION
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RB
39 of 71
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 40 (OCR)

REQUIREMENTS BULLETIN 757-57A0073
ALERT  ALERT
RIGHT WING
PRATT AND WHITNEY STRUT SHOWN,
ROLLS ROYCE STRUT SIMILAR
The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
FIGURE 6: RIGHT WING - DRAG FITTINGS AND WING UPPER SKIN - FASTENER 1-10 OPEN-HOLE HFEC
INSPECTION
(SHEET 1 OF 2)
Original Issue: July 14, 2017
Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright © Unpublished  757-57A0073 RB
Work - See page 1 for details.  40 of 71

### Page 41

More DataQtyIdentificationNameTaskStep
(a)10-Fastener HolesInspect1
(b)10-FastenerInspect2
(a) Do an open-hole HFEC inspection for any crack in accordance with 757 NDT Manual Part 6, 51-00-16.
NOTE: Use the steps in 757 NDT Manual Part 6, 51-00-16 Paragraph 6 to confirm crack indication(s).
Discrepancies in shims can cause false positive crack indications. If an indication can be confirmed to be
at the same depth and radial position as the discrepancy location, the fastener hole can be accepted. A
discrepancy is defined as a cut or rip in the shim, a shim that has migrated past the edge of the hole, or
a gap caused by shim migration outward.
(b) Do a dye-penetrant inspection, Type 1, Sensitivity 2, for any crack in the fillet between head and shank
on the removed fasteners. Refer to SOPM 20-20-02 as an accepted procedure. Discard any fasteners
that shows any crack indication. A fastener with no crack indications is considered serviceable.
FIGURE 6: RIGHT WING - DRAG FITTINGS AND WING UPPER SKIN - FASTENER 1-10 OPEN-HOLE HFEC
INSPECTION
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RB
41 of 71
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 42 (OCR)

REQUIREMENTS BULLETIN 757-57A0073
ALERT  ALERT
This Figure applies only to: Group 1-9.
LEFT WING
PRATT AND WHITNEY STRUT SHOWN,  2558993
ROLLS ROYCE STRUT SIMILAR
FIGURE 7: LEFT WING - DRAG FITTINGS AND WING UPPER SKIN - LOOSE FASTENER 11-18 OPEN-HOLE
HFEC INSPECTION
(SHEET 1 OF 2)
Original Issue: July 14, 2017
Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright © Unpublished  757-57A0073 RB
Work - See page 1 for details.  42 of 71

### Page 43

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
More DataQtyIdentificationNameTaskStep
(a)--Fastener HolesInspect1
(a) Do an open-hole HFEC inspection for any crack of the holes of loose fasteners only in accordance with
757 NDT Manual Part 6, 51-00-16.
NOTE: Use the steps in 757 NDT Manual Part 6, 51-00-16 Paragraph 6 to confirm crack indication(s).
Discrepancies in shims can cause false positive crack indications. If an indication can be confirmed to be
at the same depth and radial position as the discrepancy location, the fastener hole can be accepted. A
discrepancy is defined as a cut or rip in the shim, a shim that has migrated past the edge of the hole, or
a gap caused by shim migration outward.
FIGURE 7: LEFT WING - DRAG FITTINGS AND WING UPPER SKIN - LOOSE FASTENER 11-18 OPEN-HOLE
HFEC INSPECTION
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RB
43 of 71
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 44 (OCR)

REQUIREMENTS BULLETIN 757-57A0073
ALERT  ALERT
This Figure applies only to: Group 1-9.
RIGHT WING
PRATT AND WHITNEY STRUT SHOWN,  2558995
ROLLS ROYCE STRUT SIMILAR
FIGURE 8: RIGHT WING - DRAG FITTINGS AND WING UPPER SKIN - LOOSE FASTENER 11-18 OPEN-HOLE
HFEC INSPECTION
(SHEET 1 OF 2)
Original Issue: July 14, 2017
Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright © Unpublished  757-57A0073 RB
Work - See page 1 for details.  44 of 71

### Page 45

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
More DataQtyIdentificationNameTaskStep
(a)--Fastener HolesInspect1
(a) Do an open-hole HFEC inspection for any crack of the holes of loose fasteners only in accordance with
757 NDT Manual Part 6, 51-00-16.
NOTE: Use the steps in 757 NDT Manual Part 6, 51-00-16 Paragraph 6 to confirm crack indication(s).
Discrepancies in shims can cause false positive crack indications. If an indication can be confirmed to be
at the same depth and radial position as the discrepancy location, the fastener hole can be accepted. A
discrepancy is defined as a cut or rip in the shim, a shim that has migrated past the edge of the hole, or
a gap caused by shim migration outward.
FIGURE 8: RIGHT WING - DRAG FITTINGS AND WING UPPER SKIN - LOOSE FASTENER 11-18 OPEN-HOLE
HFEC INSPECTION
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RB
45 of 71
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 46 (OCR)

REQUIREMENTS BULLETIN 757-57A0073
ALERT  ALERT
DIAGONAL BRACE
UPPER LINK
AND
LEFT ENGINE
1.00
DIAGONAL BRACE
1.00
ROLLS-ROYCE STRUT SHOWN  INSPECTION  AREA  2566449
FIGURE 9: LEFT WING- DIAGONAL BRACE AND FITTINGS - GENERAL VISUAL INSPECTION FOR
CRACKS
(SHEET 1 OF 3)
Original Issue: July 14, 2017
Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright © Unpublished  757-57A0073 RB
Work - See page 1 for details.  46 of 71

### Page 47 (OCR)

REQUIREMENTS BULLETIN 757-57A0073
ALERT  ALERT
DIAGONAL BRACE
MULTI-PART STRUT SHOWN
(PRATT AND WHITNEY
SINGLE-PART STRUT SIMILAR)
B  INSPECTION  AREA  2568016
FIGURE 9: LEFT WING- DIAGONAL BRACE AND FITTINGS - GENERAL VISUAL INSPECTION FOR
CRACKS
(SHEET 2 OF 3)
Original Issue: July 14, 2017
Export Controlled ECCN: 9E991 - BOEING  757-57A0073 RB
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  47 of 71

### Page 48

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
More DataQtyIdentificationNameTaskStep
(a)--Diagonal BraceInspect1
(a)--Diagonal Brace FittingsInspect
(a) Do a general visual inspection of the diagonal brace and diagonal brace fittings for any crack.
FIGURE 9: LEFT WING- DIAGONAL BRACE AND FITTINGS - GENERAL VISUAL INSPECTION FOR
CRACKS
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RB
48 of 71
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 49 (OCR)

REQUIREMENTS BULLETIN 757-57A0073
ALERT  ALERT
DIAGONAL BRACE
A AND B
RIGHT ENGINE
DIAGONAL BRACE
1.00
ROLLS-ROYCE STRUT SHOWN
INSPECTION  AREA  2566606
FIGURE 10: RIGHT WING- DIAGONAL BRACE AND FITTINGS - GENERAL VISUAL INSPECTION FOR
CRACKS
(SHEET 1 OF 3)
Original Issue: July 14, 2017
Export Controlled ECCN: 9E991 - BOEING  757-57A0073 RB
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  49 of 71

### Page 50 (OCR)

REQUIREMENTS BULLETIN 757-57A0073
ALERT  ALERT
DIAGONAL BRACE
MULTI-PART STRUT SHOWN
(PRATT AND WHITNEY
SINGLE-PART STRUT SIMILAR)
AREA  INSPECTION  2568414
FIGURE 10: RIGHT WING- DIAGONAL BRACE AND FITTINGS - GENERAL VISUAL INSPECTION FOR
CRACKS
(SHEET 2 OF 3)
Original Issue: July 14, 2017
PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  757-57A0073 RB
Work - See page 1 for details.  50 of 71

### Page 51

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
More DataQtyIdentificationNameTaskStep
(a)--Diagonal BraceInspect1
(a)--Diagonal Brace FittingsInspect
(a) Do a general visual inspection of the diagonal brace and diagonal brace fittings for any crack.
FIGURE 10: RIGHT WING- DIAGONAL BRACE AND FITTINGS - GENERAL VISUAL INSPECTION FOR
CRACKS
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RB
51 of 71
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 52 (OCR)

REQUIREMENTS BULLETIN 757-57A0073
ALERT  ALERT
LEFT WING
PRATT AND WHITNEY STRUT SHOWN,  2569202
ROLLS ROYCE STRUT SIMILAR
The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
FIGURE 11: LEFT WING - WING UPPER SKIN - DETAILED INSPECTION FOR CRACKS
(SHEET 1 OF 2)
Original Issue: July 14, 2017
Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright © Unpublished  757-57A0073 RB
Work - See page 1 for details.  52 of 71

### Page 53

More DataQtyIdentificationNameTaskStep
(a)--Wing Upper SkinInspect1
(a) Do a detailed inspection of the wing upper skin for any crack in the area shown. The boundary of the in-
spection area is 1.00 inch from the edge of the outer fasteners in the inspection area.
FIGURE 11: LEFT WING - WING UPPER SKIN - DETAILED INSPECTION FOR CRACKS
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RB
53 of 71
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 54 (OCR)

REQUIREMENTS BULLETIN 757-57A0073
ALERT  ALERT
RIGHT WING
PRATT AND WHITNEY STRUT SHOWN,  2569206
ROLLS ROYCE STRUT SIMILAR
The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
FIGURE 12: RIGHT WING - WING UPPER SKIN - DETAILED INSPECTION FOR CRACKS
(SHEET 1 OF 2)
Original Issue: July 14, 2017
Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright © Unpublished  757-57A0073 RB
Work - See page 1 for details.  54 of 71

### Page 55

More DataQtyIdentificationNameTaskStep
(a)--Wing Upper SkinInspect1
(a) Do a detailed inspection of the wing upper skin for any crack in the area shown. The boundary of the in-
spection area is 1.00 inch from the edge of the outer fasteners in the inspection area.
FIGURE 12: RIGHT WING - WING UPPER SKIN - DETAILED INSPECTION FOR CRACKS
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RB
55 of 71
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 56 (OCR)

REQUIREMENTS BULLETIN 757-57A0073
ALERT  ALERT
This Figure applies only to: Group 1-9.
FRONT SPAR
SKIN
LEFT WING
NACELLE
+15 +10 +5
A-A  2581903
FIGURE 13: LEFT WING - DRAG FITTINGS - INBOARD SHIM BOLT TORQUE CHECK
(SHEET 1 OF 2)
Original Issue: July 14, 2017
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished  Work - See page 1 for details.  1410 99

### Page 57

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
More DataQtyIdentificationNameTaskStep
(a)7-FastenerInspect1
(a) Do a torque check of the bolts shown for clamp-up torque. There are two options for this inspection:
OPTION 1: HEAD TORQUE CHECK. The joint must be unloaded to perform the torque check from the
bolt head. Refer to PART 1 of the service bulletin as an accepted procedure for unloading the joint. To
do the head torque check, secure the nut. Gradually apply a tightening torque to the bolt head until the
head test torque value is obtained. If bolt head rotation occurs below the head test torque value, the torque
check is considered to be failed. If the head test torque value is reached without bolt head rotation, the
torque check is passed. The clamp-up test torque is 160 in-lbs.
OPTION 2: NUT TORQUE CHECK. Secure the fastener head. Gradually apply a tightening torque to the
nut until the nut test torque value is obtained. If nut rotation occurs below the nut test torque value, the
torque check is considered to be failed. If the nut test torque value is reached without nut rotation, the
torque check is passed. The clamp-up test torque is 145 in-lbs.
FIGURE 13: LEFT WING - DRAG FITTINGS - INBOARD SHIM BOLT TORQUE CHECK
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RB
57 of 71
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 58 (OCR)

REQUIREMENTS BULLETIN 757-57A0073
ALERT  ALERT
This Figure applies only to: Group 1-9.
FRONT SPAR
SKIN
RIGHT WING
NACELLE
E --
-5  + 10  + 15
A-A  2581904
FIGURE 14: RIGHT WING - DRAG FITTINGS - INBOARD SHIM BOLT TORQUE CHECK
(SHEET 1 OF 2)
Original Issue: July 14, 2017
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  1410 89

### Page 59

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
More DataQtyIdentificationNameTaskStep
(a)7-FastenerInspect1
(a) Do a torque check of the bolts shown for clamp-up torque. There are two options for this inspection:
OPTION 1: HEAD TORQUE CHECK. The joint must be unloaded to perform the torque check from the
bolt head. Refer to PART 1 of the service bulletin as an accepted procedure for unloading the joint. To
do the head torque check, secure the nut. Gradually apply a tightening torque to the bolt head until the
head test torque value is obtained. If bolt head rotation occurs below the head test torque value, the torque
check is considered to be failed. If the head test torque value is reached without bolt head rotation, the
torque check is passed. The clamp-up test torque is 160 in-lbs.
OPTION 2: NUT TORQUE CHECK. Secure the fastener head. Gradually apply a tightening torque to the
nut until the nut test torque value is obtained. If nut rotation occurs below the nut test torque value, the
torque check is considered to be failed. If the nut test torque value is reached without nut rotation, the
torque check is passed. The clamp-up test torque is 145 in-lbs.
FIGURE 14: RIGHT WING - DRAG FITTINGS - INBOARD SHIM BOLT TORQUE CHECK
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 14, 2017
757-57A0073 RB
59 of 71
REQUIREMENTS BULLETIN 757-57A0073
ALERTALERT

### Page 60 (OCR)

REQUIREMENTS BULLETIN 757-57A0073
ALERT  ALERT
This Figure applies only to: Group 1-9.
FRONT SPAR
SKIN
LEFT WING
NACELLE
- 10
A-A  2581905
FIGURE 15: LEFT WING - DRAG FITTINGS - OUTBOARD SHIM BOLT TORQUE CHECK
(SHEET 1 OF 2)
Original Issue: July 14, 2017
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished  Work - See page 1 for details.  1410 09

The text continues at https://openairdocs.org/service-documents/boeing/757-57a0073-rb/file/e67b742b3c43.md?from=61

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
