# Boeing Alert Service Bulletin 767-27A0227: No revision named

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2013-0869; AD 2014-09-10 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Alert Service Bulletin 767-27A0227](https://openairdocs.org/service-documents/boeing/767-27a0227.md)
- Title as filed: U.S. DOT/FAA - SB-767-27A0227-00
- Pages: 78
- PDF: https://openairdocs.org/files/sha256/57/3c/573c4ad1bff9a1dd6f635484e380c2da5852a38a04afa4f74599935cbcdbd91b
- Page: https://openairdocs.org/service-documents/boeing/767-27a0227/file/573c4ad1bff9

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Commercial 
Airplanes
767
Service Bulletin
ALERT
Number: 767-27A0227
Original Issue: February 12, 2013
ATA System: 2751
SUBJECT: FLIGHT CONTROLS - Flaps - Outboard Flap Actuator Crank Arm Mechanism - Flap
Positions 1, 2, 7 and 8 Bearing Inspection/Replacement
Export of this technology is controlled under the United States Export Administration Regulations (EAR) (15
CFR 300-774). An export license may be required before it is used for development, production or use by foreign
persons from specific countries. The controller of this data has the individual responsibility to abide by all export
laws.
9E991ECCN:
BOEING PROPRIETARY, CONFIDENTIAL AND/OR TRADE SECRET
Copyright © 2013 Boeing.
Unpublished Work. All Rights Reserved.
Treatment of this document and its content is governed by contract with Boeing. Rights to use this document
are licensed on a per aircraft basis and such rights may not be transferable. For more information, contact The
Boeing Company.
Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner™,
BBJ, DC-8, DC-9, DC-10, KC-10, KDC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8A, Poseidon and Boeing
liveries are all trademarks owned by The Boeing Company; and no trademark license is granted in connection
with this document unless provided in writing by Boeing. BOEING is a trademark of Boeing Management
Company.
Original Issue: February 12, 2013
767-27A0227
1 of 78
4.0

### Page 2

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 12, 2013
767-27A0227
2 of 78
BOEING SERVICE BULLETIN 767-27A0227
ALERTALERT
BLANK PAGE

### Page 3

Table of Contents
Summary ...................................................... 5
1. PLANNING INFORMATION ........................................ 1 1
A. Effectivity ............................................... 1 1
1. Airplanes ............................................ 1 1
2. Spares Affected ........................................ 1 3
B. Concurrent Requirements ...................................... 1 3
C. Reason ................................................ 1 4
D. Description .............................................. 1 5
E. Compliance .............................................. 1 6
F. Approval ............................................... 2 6
G. Manpower .............................................. 2 7
H. Weight and Balance Changes .................................... 2 9
I. Electrical Load Data ......................................... 2 9
J. References .............................................. 2 9
1. Existing Data: ......................................... 2 9
2. Data Supplied with this Service Bulletin: ........................... 2 9
3. Installation Drawings Used in the Preparation of this Service Bulletin: ........... 2 9
K. Publications Affected ........................................ 3 0
L. Interchangeability and Intermixability of Parts ........................... 3 0
M. Software Accomplishment Summary ................................ 3 0
2. MATERIAL INFORMATION ........................................ 3 1
A. Material - Price and Availability ................................... 3 1
B. Industry Support Information .................................... 3 1
C. Parts Necessary for Each Airplane ................................. 3 1
1. Kits/Parts ............................................ 3 1
2. Parts and Materials Supplied by the Operator ........................ 3 2
3. Parts Modified and Reidentified ................................ 3 3
4. Parts Removed and Not Replaced .............................. 3 4
D. Parts Necessary to Change Spares ................................. 3 4
E. Special Tooling - Price and Availability ............................... 3 5
F. Special Tooling Necessary to do this Service Bulletin ....................... 3 5
3. ACCOMPLISHMENT INSTRUCTIONS .................................. 3 7
A. GENERAL INFORMATION ..................................... 3 7
B. WORK INSTRUCTIONS ....................................... 3 8
FIGURE 1: INSPECT THE TRAILING EDGE FLAP SUPPORT BEARINGS AT THE TE FLAP SUPPORT
RIB ASSEMBLY IN FLAP POSITIONS 1, 2, 7, AND 8, OUTBOARD SIDE [Group 1-3,
Configuration 2] ......................................... 5 2
FIGURE 2: INSPECT THE TRAILING EDGE FLAP SUPPORT BEARINGS AT THE TE FLAP SUPPORT
RIB ASSEMBLY IN FLAP POSITIONS 1, 2, 7, AND 8, INBOARD SIDE [Group 1-3, Configuration
2 ]  ................................................ 5 5
FIGURE 3: RESTORE THE TRAILING EDGE FLAP SUPPORT BEARINGS AT THE TE FLAP SUPPORT
RIB ASSEMBLY IN FLAP POSITIONS 1, 2, 7, AND 8, OUTBOARD SIDE [Group 1-3,
Configuration 2] ......................................... 5 8
FIGURE 4: RESTORE THE TRAILING EDGE FLAP SUPPORT BEARINGS AT THE TE FLAP SUPPORT
RIB ASSEMBLY IN FLAP POSITIONS 1, 2, 7, AND 8, INBOARD SIDE [Group 1-3, Configuration
2 ]  ................................................ 6 1
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 12, 2013
767-27A0227
3 of 78
BOEING SERVICE BULLETIN 767-27A0227
ALERTALERT

### Page 4

FIGURE 5: REPLACE THE TRAILING EDGE FLAP SUPPORT BEARINGS AT THE TE FLAP SUPPORT
RIB ASSEMBLY IN FLAP POSITION 1 [Group 1-3, Configuration 2] ............ 6 3
FIGURE 6: REPLACE THE TRAILING EDGE FLAP SUPPORT BEARINGS AT THE TE FLAP SUPPORT
RIB ASSEMBLY IN FLAP POSITION 2 [Group 1-3, Configuration 2] ............ 6 6
FIGURE 7: REPLACE THE TRAILING EDGE FLAP SUPPORT BEARINGS AT THE TE FLAP SUPPORT
RIB ASSEMBLY IN FLAP POSITION 7 [Group 1-3, Configuration 2] ............ 6 9
FIGURE 8: REPLACE THE TRAILING EDGE FLAP SUPPORT BEARINGS AT THE TE FLAP SUPPORT
RIB ASSEMBLY IN FLAP POSITION 8 [Group 1-3, Configuration 2] ............ 7 2
FIGURE 9: RE-IDENTIFY THE TRAILING EDGE (TE) FLAP SUPPORT RIB ASSEMBLY FOR APPLICABLE
FLAP POSITIONS WITH CORRECT NEW PART NUMBERS [Group 1, 3, Configuration 1] . 75
APPENDIX A: BEARING DAMAGE DEFINITIONS AND SUGGESTED WORKSHEET TO RECORD THE
CONDITION OF THE REMOVED BEARINGS [Group 1-3, Configuration 2] ........ 7 6
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 12, 2013
767-27A0227
4 of 78
BOEING SERVICE BULLETIN 767-27A0227
ALERTALERT

### Page 5

Commercial 
Airplanes
767
Service Bulletin
ALERT
SummaryNumber: 767-27A0227Original Issue: February 12, 2013
ATA System: 2751
SUBJECT: FLIGHT CONTROLS - Flaps - Outboard Flap Actuator Crank Arm Mechanism - Flap
Positions 1, 2, 7 and 8 Bearing Inspection/Replacement
THIS BULLETIN IS SENT TO THE OPERATORS OF RECORD OF THE AIRPLANES SHOWN IN PARAGRAPH
1.A., EFFECTIVITY. IF AN AIRPLANE HAS BEEN LEASED OR SOLD, SEND THIS SERVICE BULLETIN TO
THE NEW OPERATOR. IF APPLICABLE SPARES HAVE BEEN SOLD, SEND THIS SERVICE BULLETIN TO
THE NEW OWNER.
CONCURRENT REQUIREMENTS
None.
BACKGROUND
Accomplishment of this service bulletin will replace the Trailing Edge (TE) Flap support bearings without a roller
retention feature at the TE Flap support rib assembly in Flap Positions 1, 2, 7, and 8 with new bearings with a
roller retention feature. The TE Flap support bearings are integral components of the TE Flap support rib
assemblies. The TE Flap rotary actuators and position transmitters are attached to the TE support rib assemblies
along the rear spar. Not replacing the TE Flap support bearings can, in the event of an undetected bearing
failure, lead to damage to the TE rotary actuators and other TE Flap support rib parts, which could result in a
dual Flap drive system disconnect in both TE Flap rotary actuators, and a possible Flaps blowback with loss of
controllability of the airplane.
There have been several cases of varying degrees of TE Flap support bearings damage at the TE Flap support
rib assemblies in Flap Positions 1, 2, 4, 5, 7, and 8. An operator reported "TE FLAP ASYM" and "TE SHUT
DOWN" messages at Flap 5 during a landing approach. Bearing damage was found at the Outboard E Flap
support rib assembly in Flap Positions 1, 2, 7, and 8, and at the Inboard TE Flap support rib assembly in Positions
4 and 5. The inspection of a second airplane revealed similar TE Flap support bearing damage, but no EICAS
messages were experienced in that case. A third airplane was inspected by another operator, and similar damage
to the TE Flap support bearings was found, but no EICAS messages were experienced in that case either.
Another operator found a broken position transmitter gearbox on a fourth airplane after receiving a Flap skew
message. This airplane also had TE Flap support bearing damage in the TE Flap support rib assembly at various
TE Flap Positions. Bearing damage in the TE Flaps support rib assembly is caused by the use of dead-blow
mallets during the installation of the shaft on the TE Flap support rib assembly when TE Flap support bearings
without a roller retention feature are installed. This method of installation may compromise bearings without a
roller retention feature. The TE Flap support bearings in TE Flap Positions 3 and 6 are not affected.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 12, 2013
767-27A0227
5 of 78

### Page 6

This service bulletin replaces Boeing service bulletin 767-27A0222, Original Issue. More work is necessary for
Group 1, Configuration 1 airplanes (airplanes that accomplished the terminating action given in Boeing service
bulletin 767-27A0222, Original Issue) to maintain part number configuration control of the flap support rib
assemblies. For these airplanes, the new part numbers for TE Flap support rib assembly in Flap Positions 1
and 8 were incorrect in 767-27A0222, Original Issue. The TE Flap support rib assembly part numbers should
be changed to the correct part number on the affected airplanes in this group/configuration. No more work is
necessary for Group 2, Configuration 1 airplanes. For this airplane, the new part numbers for TE Flap support
rib assembly in Flap Positions 1 and 8 were correct in 767-27A0222, Original Issue.
This service bulletin does not provide instructions to inspect/replace the TE Flap support bearings and the rotary
actuators at Flap Positions 4 and 5. The TE Flap support bearings and TE rotary actuators at these Flap Positions
are covered by service bulletin 767-27-0223. The TE Flap support bearings and TE rotary actuators at Flap
Positions 3 and 6 are not affected by the condition addressed in this service bulletin
Boeing Service Related Problem (SRP) 767-SRP-57-0235 and SRP 767-SRP-57-0255 are related to this service
bulletin.
This table is provided to operators for planning purposes only. Refer to the applicable sections for more
information.
ReferenceAffectedPlanning Data
Paragraph 1.A.2., Spares AffectedYesSpares Affected
Paragraph 1.E., Compliance and Paragraph
1.F., Approval
YesAD Related
Paragraph 1.H., Weight and Balance ChangesNoWeight and Balance Change
Paragraph 1.I., Electrical Load DataNoElectrical Load Changed
Paragraph 1.K., Publications AffectedYesPublications Affected
Paragraph 1.K., Publications AffectedNoAirplane Flight Operations Affected (Flight Crew
Operations Manual or FAA Approved Airplane
Flight Manual)
Paragraph 2.C.1., Kits/PartsYesKits/Parts Required
Paragraph 2.C.2., Parts and Materials Supplied
by the Operator
YesOperator Supplied Parts/Material
Paragraph 2.F., Special Tooling Necessary to
do this Service Bulletin
NoSpecial Tooling Required
ACTION
Group 1, 3, Configuration 1:
RE-IDENTIFY THE TRAILING EDGE (TE) FLAP SUPPORT RIB ASSEMBLY FOR APPLICABLE FLAP
POSITIONS WITH CORRECT NEW PART NUMBERS
1. Do PART 3 to reidentify the TE Flap support rib assembly at the applicable Flap Positions with the
correct new part numbers.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 12, 2013
767-27A0227
6 of 78
BOEING SERVICE BULLETIN 767-27A0227
ALERTALERT

### Page 7

Group 2, Configuration 1:
1. No action required.
Group 1-3, Configuration 2:
INSPECT THE TE FLAP SUPPORT BEARINGS AT THE TE FLAP SUPPORT RIB ASSEMBLY IN FLAP
POSITIONS 1, 2, 7, AND 8:
1. Do PART 1A to do a General Visual Inspection (GVI) of the TE Flap support bearings at the TE Flap
support rib assembly in Flap Positions 1, 2, 7, and 8 to identify the type of bearing installed.
a. PART 1A, STEP 7, CONDITION 1: Two bearings with a roller retention feature are installed at the
TE Flap support rib assembly in Flap Positions 1, 2, 7, and 8.
– No bearing replacement is required. Put the airplane back to a serviceable condition in
accordance with Accomplishment Instructions PART 1B.
a. PART 1A, STEP 7, CONDITION 2: At least one bearing without a roller retention feature is installed
at the TE Flap support rib assembly in Flap Position1, 2, 7, or 8.
– Replace the two bearings at each applicable TE Flap support rib in accordance with
Accomplishment Instructions PART 2.
– Do a General Visual Inspection (GVI) of each pair of bearings removed in accordance with
Accomplishment Instructions PART 2, Step 1.d.
Group 1-3, Configuration 2:
REPLACE THE TRAILING EDGE (TE) FLAP SUPPORT BEARINGS AT THE TE FLAP SUPPORT RIB
ASSEMBLY IN FLAP POSITIONS 1, 2, 7, or 8:
1. Do PART 2 to replace the applicable TE Flap support bearings at the TE Flap support rib assembly in
Flap Positions 1, 2, 7, or 8 after bearing the inspection in PART 1A if one or more bearings, at any of
the applicable TE Flap Positions, do not have a roller retention feature.
2. Do a GVI of the removed TE Flap support bearings and record the damage / type bearing combination.
Use the data to find if the TE rotary actuators at Flap Positions 1, 2, 7, or 8 are serviceable or if they
need to be overhauled or replaced.
a. PART 2, STEP 1.f, 2.f, 3.f, or 4.f., CONDITION 1: Both TE Flap support bearings at TE Flap support
rib assembly in Flap Position 1 have at least one face each that meets the definitions of good or
slightly damaged bearing face.
– PART 2, Step 1.f, CONDITION 1, Step 1: The TE rotary actuator is acceptable and may be
used as-is in the applicable Flap Position(s).
b. PART 2, STEP 1.f, 2.f, 3.f, or 4.f., CONDITION 2: Only one TE Flap support bearing at the TE
Flap support rib assembly in Flap Position 1 has at least one face that meets the definition of good
or slightly damaged bearing face. The other bearing at the same TE Flap support rib assembly
has faces that meet the definitions of moderately damaged or fractured bearing face.
– PART 2, Step 1.f, CONDITION 2, Step 1: Overhaul or replace the TE rotary actuator at the
TE Flap support rib assembly in the applicable Flap Position(s).
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 12, 2013
767-27A0227
7 of 78
BOEING SERVICE BULLETIN 767-27A0227
ALERTALERT

### Page 8

c. PART 2, STEP 1.f, 2.f, 3.f, or 4.f., CONDITION 3: Both bearings at the TE Flap support rib assembly
in Flap Position 1 have all faces that meet the definitions of moderately damaged or fractured
bearing face.
– PART 2, Step 1.f, CONDITION 3, Step 1: Replace the TE rotary actuator at the TE Flap
support rib assembly in the applicable Flap Position(s).
Group 1-3, Configuration 2:
FUNCTIONAL TEST AFTER BEARING REPLACEMENT:
1. Do the functional test after the TE Flap rib support bearings have been replaced at Flap Position 1, 2,
7 or 8.
EFFECTIVITY
767-200/-300/-300F/-400ER Airplanes that have bearings without a roller retention feature installed at the Trailing
Edge (TE) Flap support ribs. Refer to Paragraph 1.A.1., Airplanes, for the list of affected airplanes.
COMPLIANCE
The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to this service
bulletin. The Airworthiness Directive will make the compliance tasks and times given in this service bulletin
mandatory.
Refer to Paragraph 1.E., Compliance.
INDUSTRY SUPPORT INFORMATION
Boeing warranty remedies are available for airplanes in warranty as of July 15, 2009. Please refer to Paragraph
2.B., Industry Support Information.
MANPOWER
Refer to Paragraph 1.G., Manpower.
MATERIAL INFORMATION
Boeing Supplied Kits/Parts.
Refer to Paragraph 2.A., Material - Price and Availability.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 12, 2013
767-27A0227
8 of 78
BOEING SERVICE BULLETIN 767-27A0227
ALERTALERT

### Page 9 (OCR)

BOEING SERVICE BULLETIN 767-27A0227
ALERT  ALERT
WING
STA 798
POSITION 1
INSPECT THE FLAP BEARINGS
OUTBOARD SIDE AND INBOARD
SIDE
INBOARD
REPLACE BEARINGS IF  SIDE
NECESSARY IN POSITIONS
1 AND 8.
REPLACE BEARINGS IN
POSITION 1, 2, 7, AND 8 TO
TERMINATE INSPECTION
FWD
SIDE
TRAILING EDGE (TE) FLAP SUPPORT RIB POSITION 1 SHOWN
TE FLAP SUPPORT RIB POSITION 8 OPPOSITE
POSITIONS 2 AND 7, SIMILAR
Original Issue: February 12, 2013
Export Controlled ECCN: 9E991 - BOEING  767-27A0227
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  9 of 78

### Page 10

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 12, 2013
767-27A0227
10 of 78
BOEING SERVICE BULLETIN 767-27A0227
ALERTALERT
BLANK PAGE

### Page 11

Commercial 
Airplanes
767
Service Bulletin
ALERT
Number: 767-27A0227
Original Issue: February 12, 2013
ATA System: 2751
SUBJECT: FLIGHT CONTROLS - Flaps - Outboard Flap Actuator Crank Arm Mechanism - Flap
Positions 1, 2, 7 and 8 Bearing Inspection/Replacement
THIS BULLETIN IS SENT TO THE OPERATORS OF RECORD OF THE AIRPLANES SHOWN IN PARAGRAPH
1.A., EFFECTIVITY. IF AN AIRPLANE HAS BEEN LEASED OR SOLD, SEND THIS SERVICE BULLETIN TO
THE NEW OPERATOR. IF APPLICABLE SPARES HAVE BEEN SOLD, SEND THIS SERVICE BULLETIN TO
THE NEW OWNER.
1.    PLANNING INFORMATION
A. Effectivity
1. Airplanes
This service bulletin is for the airplane(s) shown below.
Refer to Service Bulletin Index D624T001 Part 3 for Airplane Variable Number, Line Number, and
Serial Number data.
DESCRIPTIONCONFIGURATIONGROUP
767-200/300/300F/400ER Airplanes Line Number 949 - 981-1
Airplanes that accomplished the terminating action in Boeing service
bulletin 767-27A0222, Original Issue, but need to repart mark the TE
Flap support rib assembly in Flap Positions 1 and 8
1
Airplanes that did not accomplish the terminating action in Boeing
service bulletin 767-27A0222, Original Issue
2
767-300F Airplane Line Number 982-2
Airplanes that accomplished the terminating action in Boeing service
bulletin 767-27A0222, Original Issue
1
Airplanes that did not accomplished the terminating action in Boeing
service bulletin 767-27A0222, Original Issue
2
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 12, 2013
767-27A0227
11 of 78

### Page 12

DESCRIPTIONCONFIGURATIONGROUP
767-300/300F/400ER Airplanes Line Number 740-810-3
Airplanes that replaced the Trailing Edge Flap support bearings with
bearings with a retention feature, but need to repart mark the TE Flap
support rib assembly in Flap Positions 1, 2, 7 and 8
1
Airplanes that have not inspected/replaced the Trailing Edge Flap
support bearings with bearings with a retention feature
2
Airplane Models:
767-200, 767-300, 767-300F, 767-400ER
GroupVariable Number
3VQ001 - VQ009
3VQ071 - VQ073
1VQ111
1VR089
1VR108 - VR109
3VR207 - VR209
3VR256 - VR257
1VR266
3VR422
3VR441
3VR472
3VS055 - VS056
3VS076 - VS078
3VS095 - VS102
3VS112 - VS113
3VS137
3VS201 - VS203
3VS208
3VS216 - VS217
3VS270 - VS274
3VS291
3VS302
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 12, 2013
767-27A0227
12 of 78
BOEING SERVICE BULLETIN 767-27A0227
ALERTALERT

### Page 13

GroupVariable Number
3VS307
3VS316
3VS321 - VS324
3VS366 - VS367
3VS381 - VS382
3VS391 - VS392
3VS401
3VS466 - VS470
3VS486
3VS496
3VS506 - VS507
1VS716 - VS720
1VS733 - VS736
1VS904 - VS910
1VS912
1VS916
1VS921 - VS922
1VS931 - VS933
1VT531 - VT533
1VT541 - VT542
2VT543
2. Spares Affected
Examine your spares supply for the parts or components identified in Paragraph 2.C., Parts
Necessary for Each Airplane. If any parts or components are found, refer to Paragraph 2.C. for
the recommended use.
B. Concurrent Requirements
None.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 12, 2013
767-27A0227
13 of 78
BOEING SERVICE BULLETIN 767-27A0227
ALERTALERT

### Page 14

C. Reason
Accomplishment of this service bulletin will replace the Trailing Edge (TE) Flap support bearings without
a roller retention feature at the TE Flap support rib assembly in Flap Positions 1, 2, 7, and 8 with new
bearings with a roller retention feature. The TE Flap support bearings are integral components of the
TE Flap support rib assemblies. The TE Flap rotary actuators and position transmitters are attached
to the TE support rib assemblies along the rear spar. Not replacing the TE Flap support bearings can,
in the event of an undetected bearing failure, lead to damage to the TE rotary actuators and other TE
Flap support rib parts, which could result in a dual Flap drive system disconnect in both TE Flap rotary
actuators, and a possible Flaps blowback with loss of controllability of the airplane.
There have been several cases of varying degrees of TE Flap support bearings damage at the TE Flap
support rib assemblies in Flap Positions 1, 2, 4, 5, 7, and 8. An operator reported "TE FLAP ASYM"
and "TE SHUT DOWN" messages at Flap 5 during a landing approach. Bearing damage was found
at the Outboard E Flap support rib assembly in Flap Positions 1, 2, 7, and 8, and at the Inboard TE
Flap support rib assembly in Positions 4 and 5. The inspection of a second airplane revealed similar
TE Flap support bearing damage, but no EICAS messages were experienced in that case. A third
airplane was inspected by another operator, and similar damage to the TE Flap support bearings was
found, but no EICAS messages were experienced in that case either. Another operator found a broken
position transmitter gearbox on a fourth airplane after receiving a Flap skew message. This airplane
also had TE Flap support bearing damage in the TE Flap support rib assembly at various TE Flap
Positions. Bearing damage in the TE Flaps support rib assembly is caused by the use of dead-blow
mallets during the installation of the shaft on the TE Flap support rib assembly when TE Flap support
bearings without a roller retention feature are installed. This method of installation may compromise
bearings without a roller retention feature. The TE Flap support bearings in TE Flap Positions 3 and 6
are not affected.
This service bulletin replaces Boeing service bulletin 767-27A0222, Original Issue. More work is
necessary for Group 1, Configuration 1 airplanes (airplanes that accomplished the terminating action
given in Boeing service bulletin 767-27A0222, Original Issue) to maintain part number configuration
control of the flap support rib assemblies. For these airplanes, the new part numbers for TE Flap support
rib assembly in Flap Positions 1 and 8 were incorrect in 767-27A0222, Original Issue. The TE Flap
support rib assembly part numbers should be changed to the correct part number on the affected
airplanes in this group/configuration. No more work is necessary for Group 2, Configuration 1 airplanes.
For this airplane, the new part numbers for TE Flap support rib assembly in Flap Positions 1 and 8
were correct in 767-27A0222, Original Issue.
This service bulletin does not provide instructions to inspect/replace the TE Flap support bearings and
the rotary actuators at Flap Positions 4 and 5. The TE Flap support bearings and TE rotary actuators
at these Flap Positions are covered by service bulletin 767-27-0223. The TE Flap support bearings
and TE rotary actuators at Flap Positions 3 and 6 are not affected by the condition addressed in this
service bulletin
Boeing Service Related Problem (SRP) 767-SRP-57-0235 and SRP 767-SRP-57-0255 are related to
this service bulletin.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 12, 2013
767-27A0227
14 of 78
BOEING SERVICE BULLETIN 767-27A0227
ALERTALERT

### Page 15

D. Description
Group 1, 3, Configuration 1:
RE-IDENTIFY THE TRAILING EDGE (TE) FLAP SUPPORT RIB ASSEMBLY FOR APPLICABLE
FLAP POSITIONS WITH CORRECT NEW PART NUMBERS
1. Do PART 3 to reidentify the TE Flap support rib assembly at the applicable Flap Positions with
the correct new part numbers.
Group 2, Configuration 1:
1. No action required.
Group 1-3, Configuration 2:
INSPECT THE TE FLAP SUPPORT BEARINGS AT THE TE FLAP SUPPORT RIB ASSEMBLY IN
FLAP POSITIONS 1, 2, 7, AND 8:
1. Do PART 1A to do a General Visual Inspection (GVI) of the TE Flap support bearings at the TE
Flap support rib assembly in Flap Positions 1, 2, 7, and 8 to identify the type of bearing installed.
a. PART 1A, STEP 7, CONDITION 1: Two bearings with a roller retention feature are installed
at the TE Flap support rib assembly in Flap Positions 1, 2, 7, and 8.
– No bearing replacement is required. Put the airplane back to a serviceable condition in
accordance with Accomplishment Instructions PART 1B.
a. PART 1A, STEP 7, CONDITION 2: At least one bearing without a roller retention feature is
installed at the TE Flap support rib assembly in Flap Position1, 2, 7, or 8.
– Replace the two bearings at each applicable TE Flap support rib in accordance with
Accomplishment Instructions PART 2.
– Do a General Visual Inspection (GVI) of each pair of bearings removed in accordance
with Accomplishment Instructions PART 2, Step 1.d.
Group 1-3, Configuration 2:
REPLACE THE TRAILING EDGE (TE) FLAP SUPPORT BEARINGS AT THE TE FLAP SUPPORT
RIB ASSEMBLY IN FLAP POSITIONS 1, 2, 7, or 8:
1. Do PART 2 to replace the applicable TE Flap support bearings at the TE Flap support rib assembly
in Flap Positions 1, 2, 7, or 8 after bearing the inspection in PART 1A if one or more bearings, at
any of the applicable TE Flap Positions, do not have a roller retention feature.
2. Do a GVI of the removed TE Flap support bearings and record the damage / type bearing
combination. Use the data to find if the TE rotary actuators at Flap Positions 1, 2, 7, or 8 are
serviceable or if they need to be overhauled or replaced.
a. PART 2, STEP 1.f, 2.f, 3.f, or 4.f., CONDITION 1: Both TE Flap support bearings at TE Flap
support rib assembly in Flap Position 1 have at least one face each that meets the definitions
of good or slightly damaged bearing face.
– PART 2, Step 1.f, CONDITION 1, Step 1: The TE rotary actuator is acceptable and may
be used as-is in the applicable Flap Position(s).
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 12, 2013
767-27A0227
15 of 78
BOEING SERVICE BULLETIN 767-27A0227
ALERTALERT

### Page 16

b. PART 2, STEP 1.f, 2.f, 3.f, or 4.f., CONDITION 2: Only one TE Flap support bearing at the
TE Flap support rib assembly in Flap Position 1 has at least one face that meets the definition
of good or slightly damaged bearing face. The other bearing at the same TE Flap support rib
assembly has faces that meet the definitions of moderately damaged or fractured bearing
face.
– PART 2, Step 1.f, CONDITION 2, Step 1: Overhaul or replace the TE rotary actuator at
the TE Flap support rib assembly in the applicable Flap Position(s).
c. PART 2, STEP 1.f, 2.f, 3.f, or 4.f., CONDITION 3: Both bearings at the TE Flap support rib
assembly in Flap Position 1 have all faces that meet the definitions of moderately damaged
or fractured bearing face.
– PART 2, Step 1.f, CONDITION 3, Step 1: Replace the TE rotary actuator at the TE Flap
support rib assembly in the applicable Flap Position(s).
Group 1-3, Configuration 2:
FUNCTIONAL TEST AFTER BEARING REPLACEMENT:
1. Do the functional test after the TE Flap rib support bearings have been replaced at Flap Position
1, 2, 7 or 8.
The work in this service bulletin is done in the maintenance zone(s) given below.
Group 1:
Affected Maintenance Zones
ZoneModel
566, 666767-200, 767-300, 767-300F,
767-400ER
Group 2:
Affected Maintenance Zones
ZoneModel
566, 666767-300F
Group 3:
Affected Maintenance Zones
ZoneModel
566, 666767-300, 767-300F, 767-400ER
E. Compliance
The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to
this service bulletin. The Airworthiness Directive will make the compliance tasks and times given in this
service bulletin mandatory.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 12, 2013
767-27A0227
16 of 78
BOEING SERVICE BULLETIN 767-27A0227
ALERTALERT

### Page 17

Group 1, 3, Configuration 1:
No compliance time given.
Group 2, Configuration 1:
No further action required.
Group 1-2, Configuration 2:
Table 1: Inspect and Replace the TE Flap Support Rib Bearings at the Flap Support Rib Assembly in
Flap Positions 1, 2, 7 and 8.
Repeat Inter-
val (Not to Ex-
ceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Within 500 flight
cycles after the
original issue
date of this Ser-
vice Bulletin
Before 6,000 to-
tal flight cycles
Do a General Visual In-
spection (GVI) of both
bearings at the TE flap
support rib assembly in
Flap Positions 1, 2, 7, and
8 to determine if the bear-
ings have a roller retention
feature in accordance with
Accomplishment Instruc-
tions PART 1A
All airplanes
--No bearing replacement is
required. Put the airplane
back to a serviceable con-
dition in accordance with
Accomplishment Instruc-
tions PART 1B
PART 1A, STEP 4, CONDI-
TION 1 - Two bearings
with a roller retention fea-
ture are installed at the TE
Flap support rib assembly
in Flap Positions 1, 2, 7,
and 8
-Before further flight- Replace the two bearings
at each applicable TE Flap
support rib in accordance
with Accomplishment In-
structions PART 2
PART 1A, STEP 4, CONDI-
TION 2 - At least one
bearing without a roller re-
tention feature is installed
at the TE Flap support rib
assembly in Flap Position
1, 2, 7, or 8
- Do a General Visual In-
spection (GVI) of each pair
of bearings removed in ac-
cordance with Accomplish-
ment Instructions PART 2,
Step 1.d.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 12, 2013
767-27A0227
17 of 78
BOEING SERVICE BULLETIN 767-27A0227
ALERTALERT

### Page 18

Group 1-2, Configuration 2:
Table 1: Inspect and Replace the TE Flap Support Rib Bearings at the Flap Support Rib Assembly in
Flap Positions 1, 2, 7 and 8.
Repeat Inter-
val (Not to Ex-
ceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
--The TE rotary actuator is
acceptable and may be
used as-is in the applicable
Flap Position(s) where
CONDITION 1 is found:
PART 2, STEP 1.e, CON-
DITION 1 - Both TE Flap
support bearings at TE
Flap support rib assembly
in Flap Position 1 have at
least one face each that
meets the definitions of
good or slightly damaged
bearing face
- Flap Position 1 - In accor-
dance with Accomplish-
ment Instructions PART 2,
Step 1.e, CONDITION 1,
Step 1Or
- Flap Position 2 - In accor-
dance with Accomplish-
ment Instructions PART 2,
Step 2.e, CONDITION 1,
Step 1
PART 2, STEP 2.e, CON-
DITION 1 - Both TE Flap
support bearings at TE
Flap support rib assembly
in Flap Position 2 have at
least one face each that
meets the definitions of
good or slightly damaged
bearing face
- Flap Position 7 - In accor-
dance with Accomplish-
ment Instructions PART 2,
Step 3.e, CONDITION 1,
Step 1Or
- Flap Position 8 - In accor-
dance with Accomplish-
ment Instructions PART 2,
Step 4.e, CONDITION 1,
Step 1
PART 2, STEP 3.e, CON-
DITION 1 - Both TE Flap
support bearings at TE
Flap support rib assembly
in Flap Position 7 have at
least one face each that
meets the definitions of
good or slightly damaged
bearing face
Or
PART 2, STEP 4.e, CON-
DITION 1 - Both TE Flap
support bearings at TE
Flap support rib assembly
in Flap Position 8 have at
least one face each that
meets the definitions of
good or slightly damaged
bearing face
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 12, 2013
767-27A0227
18 of 78
BOEING SERVICE BULLETIN 767-27A0227
ALERTALERT

### Page 19

Group 1-2, Configuration 2:
Table 1: Inspect and Replace the TE Flap Support Rib Bearings at the Flap Support Rib Assembly in
Flap Positions 1, 2, 7 and 8.
Repeat Inter-
val (Not to Ex-
ceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flightOverhaul or replace the TE
rotary actuator at the TE
Flap support rib assembly
in the applicable Flap Posi-
tion(s) where CONDITION
2 is found:
PART 2, STEP 1.e, CON-
DITION 2 - Only one TE
Flap support bearing at the
TE Flap support rib assem-
bly in Flap Position 1 has
at least one face that
meets the definition of
good or slightly damaged
bearing face. The other
bearing at the same TE
Flap support rib assembly
has faces that meet the
definitions of moderately
damaged or fractured
bearing face
- Flap Position 1 - In accor-
dance with Accomplish-
ment Instructions PART 2,
Step 1.e, CONDITION 2,
Step 1, OPTION 1 or OP-
TION 2
- Flap Position 2 - In accor-
dance with Accomplish-
ment Instructions PART 2,
Step 2.e, CONDITION 2,
Step 1, OPTION 1 or OP-
TION 2
Or
PART 2, STEP 2.e, CON-
DITION 2 - Only one TE
Flap support bearing at the
TE Flap support rib assem-
bly in Flap Position 2 has
at least one face that
meets the definition of
good or slightly damaged
bearing face. The other
bearing at the same TE
Flap support rib assembly
has faces that meet the
definitions of moderately
damaged or fractured
bearing face
- Flap Position 7 - In accor-
dance with Accomplish-
ment Instructions PART 2,
Step 3.e, CONDITION 2,
Step 1, OPTION 1 or OP-
TION 2
- Flap Position 8 - In accor-
dance with Accomplish-
ment Instructions PART 2,
Step 4.e, CONDITION 2,
Step 1, OPTION 1 or OP-
TION 2
Or
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 12, 2013
767-27A0227
19 of 78
BOEING SERVICE BULLETIN 767-27A0227
ALERTALERT

### Page 20

Group 1-2, Configuration 2:
Table 1: Inspect and Replace the TE Flap Support Rib Bearings at the Flap Support Rib Assembly in
Flap Positions 1, 2, 7 and 8.
Repeat Inter-
val (Not to Ex-
ceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
PART 2, STEP 3.e, CON-
DITION 2 - Only one TE
Flap support bearing at the
TE Flap support rib assem-
bly in Flap Position 7 has
at least one face that
meets the definition of
good or slightly damaged
bearing face. The other
bearing at the same TE
Flap support rib assembly
has faces that meet the
definitions of moderately
damaged or fractured
bearing face
Or
PART 2, STEP 4.e, CON-
DITION 2 - Only one TE
Flap support bearing at the
TE Flap support rib assem-
bly in Flap Position 8 has
at least one face that
meets the definition of
good or slightly damaged
bearing face. The other
bearing at the same TE
Flap support rib assembly
has faces that meet the
definitions of moderately
damaged or fractured
bearing face
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 12, 2013
767-27A0227
20 of 78
BOEING SERVICE BULLETIN 767-27A0227
ALERTALERT

### Page 21

Group 1-2, Configuration 2:
Table 1: Inspect and Replace the TE Flap Support Rib Bearings at the Flap Support Rib Assembly in
Flap Positions 1, 2, 7 and 8.
Repeat Inter-
val (Not to Ex-
ceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flightReplace the TE rotary actu-
ator at the TE Flap support
rib assembly in the applica-
ble Flap Position(s) where
CONDITION 3 is found:
PART 2, STEP 1.e, CON-
DITION 3 - Both bearings
at the TE Flap support rib
assembly in Flap Position
1 have all faces that meet
the definitions of moderate-
ly damaged or fractured
bearing face
- Flap Position 1 - In accor-
dance with Accomplish-
ment Instructions PART 2,
Step 1.e, CONDITION 3,
Step 1
Or
PART 2, STEP 2.e, CON-
DITION 3 - Both bearings
at the TE Flap support rib
assembly in Flap Position
2 have all faces that meet
the definitions of moderate-
ly damaged or fractured
bearing face
- Flap Position 2 - In accor-
dance with Accomplish-
ment Instructions PART 2,
Step 2.e, CONDITION 3,
Step 1
- Flap Position 7 - In accor-
dance with Accomplish-
ment Instructions PART 2,
Step 3.e, CONDITION 3,
Step 1
Or
PART 2, STEP 3.e, CON-
DITION 3 - Both bearings
at the TE Flap support rib
assembly in Flap Position
7 have all faces that meet
the definitions of moderate-
ly damaged or fractured
bearing face
- Flap Position 8 - In accor-
dance with Accomplish-
ment Instructions PART 2,
Step 4.e, CONDITION 3,
Step 1
Or
PART 2, STEP 4.e, CON-
DITION 3 - Both bearings
at the TE Flap support rib
assembly in Flap Position
8 have all faces that meet
the definitions of moderate-
ly damaged or fractured
bearing face
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 12, 2013
767-27A0227
21 of 78
BOEING SERVICE BULLETIN 767-27A0227
ALERTALERT

### Page 22

Group 3, Configuration 2:
Table 2: Inspect and Replace the TE Flap Support Rib Bearings at the Flap Support Rib Assembly
in Flap Positions 1, 2, 7 and 8.
Repeat Interval
(not to Exceed)
Compliance
Time
ActionCondition
-Within 5,500
flight cycles after
the original issue
date of this ser-
vice bulletin
Do a General Visual In-
spection (GVI) of both
bearings at the TE flap
support rib assembly in
Flap Positions 1, 2, 7, and
8 to determine if the bear-
ings have a roller retention
feature in accordance with
Accomplishment Instruc-
tions PART 1A.
All airplanes
--No bearing replacement is
required. Put the airplane
back to a serviceable con-
dition in accordance with
Accomplishment Instruc-
tions PART 1B
PART 1A, STEP 4, CONDI-
TION 1 - Two bearings
with a roller retention fea-
ture are installed at the TE
Flap support rib assembly
in Flap Positions 1, 2, 7,
and 8
-Before further
flight
- Replace the two bearings
at each applicable TE Flap
support rib in accordance
with Accomplishment In-
structions PART 2
PART 1A, STEP 4, CONDI-
TION 2 - At least one
bearing without a roller re-
tention feature is installed
at the TE Flap support rib
assembly in Flap Position
1, 2, 7, or 8
- Do a General Visual In-
spection (GVI) of each pair
of bearings removed in ac-
cordance with Accomplish-
ment Instructions PART 2,
Step 1.d.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 12, 2013
767-27A0227
22 of 78
BOEING SERVICE BULLETIN 767-27A0227
ALERTALERT

### Page 23

Group 3, Configuration 2:
Table 2: Inspect and Replace the TE Flap Support Rib Bearings at the Flap Support Rib Assembly
in Flap Positions 1, 2, 7 and 8.
Repeat Interval
(not to Exceed)
Compliance
Time
ActionCondition
--The TE rotary actuator is
acceptable and may be
used as-is in the applicable
Flap Position(s) where
CONDITION 1 is found:
PART 2, STEP 1.e, CON-
DITION 1 - Both TE Flap
support bearings at TE
Flap support rib assembly
in Flap Position 1 have at
least one face each that
meets the definitions of
good or slightly damaged
bearing face
- Flap Position 1 - In accor-
dance with Accomplish-
ment Instructions PART 2,
Step 1.e, CONDITION 1,
Step 1Or
- Flap Position 2 - In accor-
dance with Accomplish-
ment Instructions PART 2,
Step 2.e, CONDITION 1,
Step 1
PART 2, STEP 2.e, CON-
DITION 1 - Both TE Flap
support bearings at TE
Flap support rib assembly
in Flap Position 2 have at
least one face each that
meets the definitions of
good or slightly damaged
bearing face
- Flap Position 7 - In accor-
dance with Accomplish-
ment Instructions PART 2,
Step 3.e, CONDITION 1,
Step 1Or
- Flap Position 8 - In accor-
dance with Accomplish-
ment Instructions PART 2,
Step 4.e, CONDITION 1,
Step 1
PART 2, STEP 3.e, CON-
DITION 1 - Both TE Flap
support bearings at TE
Flap support rib assembly
in Flap Position 7 have at
least one face each that
meets the definitions of
good or slightly damaged
bearing face
Or
PART 2, STEP 4.e, CON-
DITION 1 - Both TE Flap
support bearings at TE
Flap support rib assembly
in Flap Position 8 have at
least one face each that
meets the definitions of
good or slightly damaged
bearing face
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 12, 2013
767-27A0227
23 of 78
BOEING SERVICE BULLETIN 767-27A0227
ALERTALERT

### Page 24

Group 3, Configuration 2:
Table 2: Inspect and Replace the TE Flap Support Rib Bearings at the Flap Support Rib Assembly
in Flap Positions 1, 2, 7 and 8.
Repeat Interval
(not to Exceed)
Compliance
Time
ActionCondition
-Before further
flight
Overhaul or replace the TE
rotary actuator at the TE
Flap support rib assembly
in the applicable Flap Posi-
tion(s) where CONDITION
2 is found:
PART 2, STEP 1.e, CON-
DITION 2 - Only one TE
Flap support bearing at the
TE Flap support rib assem-
bly in Flap Position 1 has
at least one face that
meets the definition of
good or slightly damaged
bearing face. The other
bearing at the same TE
Flap support rib assembly
has faces that meet the
definitions of moderately
damaged or fractured
bearing face
- Flap Position 1 - In accor-
dance with Accomplish-
ment Instructions PART 2,
Step 1.e, CONDITION 2,
Step 1, OPTION 1 or OP-
TION 2
- Flap Position 2 - In accor-
dance with Accomplish-
ment Instructions PART 2,
Step 2.e, CONDITION 2,
Step 1, OPTION 1 or OP-
TION 2
Or
PART 2, STEP 2.e, CON-
DITION 2 - Only one TE
Flap support bearing at the
TE Flap support rib assem-
bly in Flap Position 2 has
at least one face that
meets the definition of
good or slightly damaged
bearing face. The other
bearing at the same TE
Flap support rib assembly
has faces that meet the
definitions of moderately
damaged or fractured
bearing face
- Flap Position 7 - In accor-
dance with Accomplish-
ment Instructions PART 2,
Step 3.e, CONDITION 2,
Step 1, OPTION 1 or OP-
TION 2
- Flap Position 8 - In accor-
dance with Accomplish-
ment Instructions PART 2,
Step 4.e, CONDITION 2,
Step 1, OPTION 1 or OP-
TION 2
Or
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 12, 2013
767-27A0227
24 of 78
BOEING SERVICE BULLETIN 767-27A0227
ALERTALERT

### Page 25

Group 3, Configuration 2:
Table 2: Inspect and Replace the TE Flap Support Rib Bearings at the Flap Support Rib Assembly
in Flap Positions 1, 2, 7 and 8.
Repeat Interval
(not to Exceed)
Compliance
Time
ActionCondition
PART 2, STEP 3.e, CON-
DITION 2 - Only one TE
Flap support bearing at the
TE Flap support rib assem-
bly in Flap Position 7 has
at least one face that
meets the definition of
good or slightly damaged
bearing face. The other
bearing at the same TE
Flap support rib assembly
has faces that meet the
definitions of moderately
damaged or fractured
bearing face
Or
PART 2, STEP 4.e, CON-
DITION 2 - Only one TE
Flap support bearing at the
TE Flap support rib assem-
bly in Flap Position 8 has
at least one face that
meets the definition of
good or slightly damaged
bearing face. The other
bearing at the same TE
Flap support rib assembly
has faces that meet the
definitions of moderately
damaged or fractured
bearing face
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 12, 2013
767-27A0227
25 of 78
BOEING SERVICE BULLETIN 767-27A0227
ALERTALERT

### Page 26

Group 3, Configuration 2:
Table 2: Inspect and Replace the TE Flap Support Rib Bearings at the Flap Support Rib Assembly
in Flap Positions 1, 2, 7 and 8.
Repeat Interval
(not to Exceed)
Compliance
Time
ActionCondition
-Before further
flight
Replace the TE rotary actu-
ator at the TE Flap support
rib assembly in the applica-
ble Flap Position(s) where
CONDITION 3 is found:
PART 2, STEP 1.e, CON-
DITION 3 - Both bearings
at the TE Flap support rib
assembly in Flap Position
1 have all faces that meet
the definitions of moderate-
ly damaged or fractured
bearing face
- Flap Position 1 - In accor-
dance with Accomplish-
ment Instructions PART 2,
Step 1.e, CONDITION 3,
Step 1
Or
PART 2, STEP 2.e, CON-
DITION 3 - Both bearings
at the TE Flap support rib
assembly in Flap Position
2 have all faces that meet
the definitions of moderate-
ly damaged or fractured
bearing face
- Flap Position 2 - In accor-
dance with Accomplish-
ment Instructions PART 2,
Step 2.e, CONDITION 3,
Step 1
- Flap Position 7 - In accor-
dance with Accomplish-
ment Instructions PART 2,
Step 3.e, CONDITION 3,
Step 1
Or
PART 2, STEP 3.e, CON-
DITION 3 - Both bearings
at the TE Flap support rib
assembly in Flap Position
7 have all faces that meet
the definitions of moderate-
ly damaged or fractured
bearing face
- Flap Position 8 - In accor-
dance with Accomplish-
ment Instructions PART 2,
Step 4.e, CONDITION 3,
Step 1
Or
PART 2, STEP 4.e, CON-
DITION 3 - Both bearings
at the TE Flap support rib
assembly in Flap Position
8 have all faces that meet
the definitions of moderate-
ly damaged or fractured
bearing face
F. Approval
This service bulletin was examined by the Federal Aviation Administration (FAA). The changes specified
in this service bulletin comply with the applicable regulations and are FAA approved, as well as European
Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved
airplanes listed in the service bulletin effectivity. This service bulletin and its approval were based on
the airplane in its original Boeing delivery configuration or as modified by other approved Boeing
changes.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 12, 2013
767-27A0227
26 of 78
BOEING SERVICE BULLETIN 767-27A0227
ALERTALERT

### Page 27

If an airplane has a non-Boeing modification or repair that affects a component or system also affected
by this service bulletin, the operator is responsible for obtaining appropriate regulatory agency approval
before incorporating this service bulletin.
G. Manpower
Group 1-3, Configuration 2:
Table 2: Inspection/Replacement of the TE Flap Support Rib Bearings at the TE Flap Support Rib
Assembly in Flap Position 2
NotesElapsed HoursTask-HoursNumber of PersonsTask
1.751.751PREPARE
1.252.502FIGURE 1
1.252.502FIGURE 2
(a)1.252.502FIGURE 3
(a)1.252.502FIGURE 4
1.252.502FIGURE 6
(b)0.501.002FUNCTIONAL TEST
8.5012.75Total per rib position
(a) FIGURE 3 and FIGURE 4 are required only if the bearing inspection in FIGURE 1 and FIGURE
2 finds bearings with a roller retention feature.
(b) FUNCTIONAL TEST is required only if bearings are replaced in any of the applicable Flap Posi-
tions (1, 2, 7 or 8).
Group 1-3, Configuration 2:
Table 1: Inspection/Replacement of the TE Flap Support Rib Bearings at the TE Flap Support Rib
Assembly in Flap Position 1
NotesElapsed HoursTask-HoursNumber of PersonsTask
1.751.751PREPARE
1.252.502FIGURE 1
1.252.502FIGURE 2
(a)1.252.502FIGURE 3
(a)1.252.502FIGURE 4
1.252.502FIGURE 5
(b)0.501.002FUNCTIONAL TEST
8.5012.75Total per rib position
(a) FIGURE 3 and FIGURE 4 are required only if the bearing inspection in FIGURE 1 and FIGURE
2 finds bearings with a roller retention feature.
(b) FUNCTIONAL TEST is required only if bearings are replaced in any of the applicable Flap Posi-
tions (1, 2, 7 or 8).
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 12, 2013
767-27A0227
27 of 78
BOEING SERVICE BULLETIN 767-27A0227
ALERTALERT

### Page 28

Group 1-3, Configuration 2:
Table 3: Inspection/Replacement of the TE Flap Support Rib Bearings at the TE Flap Support Rib
Assembly in Flap Position 7
NotesElapsed HoursTask-HoursNumber of PersonsTask
1.751.751PREPARE
1.252.502FIGURE 1
1.252.502FIGURE 2
(a)1.252.502FIGURE 3
(a)1.252.502FIGURE 4
1.252.502FIGURE 7
(b)0.501.002FUNCTIONAL TEST
8.5012.75Total per rib position
(a) FIGURE 3 and FIGURE 4 are required only if the bearing inspection in FIGURE 1 and FIGURE
2 finds bearings with a roller retention feature.
(b) FUNCTIONAL TEST is required only if bearings are replaced in any of the applicable Flap Posi-
tions (1, 2, 7 or 8).
Group 1-3, Configuration 2:
Table 4: Inspection/Replacement of the TE Flap Support Rib Bearings at the TE Flap Support Rib
Assembly in Flap Position 8
NotesElapsed HoursTask-HoursNumber of PersonsTask
1.751.751PREPARE
1.252.502FIGURE 1
1.252.502FIGURE 2
(a)1.252.502FIGURE 3
(a)1.252.502FIGURE 4
1.252.502FIGURE 8
(b)0.501.002FUNCTIONAL TEST
8.5012.75Total per rib position
(a) FIGURE 3 and FIGURE 4 are required only if the bearing inspection in FIGURE 1 and FIGURE
2 finds bearings with a roller retention feature.
(b) FUNCTIONAL TEST is required only if bearings are replaced in any of the applicable Flap Posi-
tions (1, 2, 7 or 8).
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 12, 2013
767-27A0227
28 of 78
BOEING SERVICE BULLETIN 767-27A0227
ALERTALERT

### Page 29

Group 1, 3, Configuration 1:
Table 5: Reidentify the TE Flap Support Rib Sssembly at Flap Position 1 and Position
8 with the Correct New Part Numbers
Elapsed HoursTask-HoursNumber of Per-
sons
Task
1.751.751Prepare
0.250.502FIGURE 9
2.002.25Total per rib position
Group 2, Configuration 1:
No further action required.
H. Weight and Balance Changes
None.
I. Electrical Load Data
None.
J. References
1. Existing Data:
a. Boeing Service Bulletin 767-27A0222, 767-27-0223
b. Boeing Service Related Problem (SRP) 767-SRP-57-0235, 767-SRP-57-0255
c. Component Maintenance Manual (CMM) 27-51-10, 27-51-49
d. Service Bulletin Index D624T001
e. Standard Overhaul Practices Manual (SOPM) 20-30-03, 20-50-10
f. 767 Aircraft Maintenance Manual (AMM) 06-44-00, 20-10-23, 24-22-00, 27-51-00, 27-51-21,
27-51-22, 27-51-45, 27-61-00, 29-11-00, 32-00-15, 32-00-20
2. Data Supplied with this Service Bulletin:
None.
3. Installation Drawings Used in the Preparation of this Service Bulletin:
TitleDrawing Number
RIB - SUPPORT NO. 1 T.E FLAP113T1328
RIB - SUPPORT NO. 2 T.E FLAP113T1329
RIB INSTL - OUTBOARD T.E. FLAP SUPPORT113T1345
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 12, 2013
767-27A0227
29 of 78
BOEING SERVICE BULLETIN 767-27A0227
ALERTALERT

### Page 30

These drawings were used to prepare this service bulletin. These drawings are not necessary to
make the specified changes, and are not supplied with this service bulletin. These drawings may
not be applicable to all airplane configurations or operators.
K. Publications Affected
1. Publications:
Chapter-SectionPublication
27-51767 Aircraft Maintenance Manual
27-51767 Illustrated Parts Catalog
2. Damage Tolerance Based Structural Inspections:
Boeing has evaluated the repairs or changes in this service bulletin for effects on Fatigue Critical
Structure (FCS) and for changes to Damage Tolerance Inspections (DTI) required in the
Maintenance Program. This service bulletin does not affect FCS, therefore DTIs are not necessary.
L. Interchangeability and Intermixability of Parts
Refer to Paragraph 2.C., Parts Necessary for Each Airplane, for interchangeability and intermixability
information.
M. Software Accomplishment Summary
Not affected.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 12, 2013
767-27A0227
30 of 78
BOEING SERVICE BULLETIN 767-27A0227
ALERTALERT

### Page 31

2.    MATERIAL INFORMATION
A. Material - Price and Availability
Boeing can supply the kits shown in Paragraph 2.C., Parts Necessary for Each Airplane, as shown
below. If there is a limit to the quantity of available kits, a supply sequence is given by Spares. More
kits become available as shown in the Reorder Lead Time (ROLT). ROLT is calculated from the date
Boeing gets the purchase order.
Unit Price thru
August 31, 2013
ROLT (Weeks)NameKit Number
$1,484.0043Top Kit - 767 TE Flap Bearing
Replacement
015T1847-2
(a) One (1) kit required per applicable Flap Position: up to four (4) kits required per airplane (one
for each TE Flap support rib assembly in Flap Positions 1, 2, 7, and 8).
The kits are subject to the terms and conditions of the Boeing standard purchase order acknowledgment.
After the Unit Price date, new price and ROLT data is applicable. Prices are in United States dollars.
Terms: Net 30 days.
Reference this service bulletin and submit your purchase order by one of the methods that follow:
1. Order on-line via ATA Spec 2000 or Boeing Part Page
2. Fax to (206) 662-7145
3. Mail to:
Spares Customer Support - MC 36-65
Boeing Spares Department
P.O. Box 3707
Seattle, Washington 98124-2207 USA
B. Industry Support Information
Boeing warranty remedies are available for 767 airplanes in warranty as of July 15, 2009. For task hour
reimbursement for airplanes in warranty as of that date, send a warranty claim to Boeing Commercial
Airplanes Group - Warranties. The kits and parts for airplanes in warranty as of that date will be supplied
at no charge. Send a purchase order for the kits and parts to Boeing Spares. Please refer to this service
bulletin number and reference the airplane variable numbers in your purchase order.
C. Parts Necessary for Each Airplane
1. Kits/Parts
To get the kits/parts shown below, refer to Paragraph 2.A., Material - Price and Availability.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 12, 2013
767-27A0227
31 of 78
BOEING SERVICE BULLETIN 767-27A0227
ALERTALERT

### Page 32

Kit 015T1847-2
NotesExisting Part
Number
NameQTYNew Part Number
-
(a) (b)
(c) (d)
60B00178-23
(DAT72-90A1-
501)
BEARING2SB-1131
(c) (d)113T1256-31SEAL4113T1256-31
(a) SB-1131 bearings (McGill) have a roller retention feature, and qualify
to two Boeing specifications, 60B00178-23 and S113T134-1. Boeing
specification 60B00178-23 does not require a roller retention feature
for the bearings, while Boeing specification S113T134-1 does. McGill
bearings packing and documentation usually include the part information
for the vendor part number (SB-1131, in this case) and a Boeing
specification number (60B00178-23 or S113T134-1). For this service
bulletin, the intent is to install new bearings that comply with Boeing
specification number S113T134-1, regardless if the bearing qualifies
for other Boeing specifications as well. Any substitute bearing for the
McGill SB-1131 must have a roller retention feature and meet Boeing
specifications given in S113T134-1 (such as DAT72-90A1-506, for ex-
ample),
(b) The second bearing qualified to the 60B00178-23 Boeing specification
is the bearing DAT72-90A1-501 (Rexnord). This bearing does not have
a roller retention feature. Rexnord bearings DAT72-90A1-501 must be
removed from spares inventories and service.
(c) Discard the existing part. For the existing bearings, discard as long as
there is no roller retention feature.
(d) You cannot use the existing part to replace the new or changed part.
NOTE: One top kit and the items shown in Paragraph 2.C.2., Parts and Materials Supplied by
the Operator, are necessary for each Trailing Edge Flap position. A total of four kits are
necessary per airplane.
2. Parts and Materials Supplied by the Operator
NotesNameQTYPart Number /
Specification
or equivalent.Safety Lockwire-MS20995NC40
-Corrosion Inhibiting Compound-BMS3-38
-Grease-BMS3-33
or equivalent.Solvent-BMS11-9
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 12, 2013
767-27A0227
32 of 78
BOEING SERVICE BULLETIN 767-27A0227
ALERTALERT

### Page 33

NotesNameQTYPart Number /
Specification
Quantity of TE rotary actua-
tors depends on the number
of rotary actuators that need
to be replaced. Up to 4 TE
rotary actuators may be
needed per airplane.
Trailing Edge (TE) Rotary Actuator0-4256T3250-4
(a)
Quantity of TE rotary actua-
tors depends on the number
of rotary actuators that need
to be replaced. Up to 4 TE
rotary actuators may be
needed per airplane.
TE Rotary Actuator0-4256T6110-3
(b)
(a) 767-200/-300/-300F Airplanes. Applicable CMM 27-51-10.
(b) 767-400ER Airplanes. Applicable CMM 27-51-49.
3. Parts Modified and Reidentified
The parts shown below are changed as shown in this service bulletin. The quantity (QTY) is the
number of parts changed on each airplane.
Group 1:
NotesNew Part NumberNameQTYExisting Part
Number
(a)015T1847-7RIB SUPPORT 11113T1328-1
(a)015T1847-3RIB SUPPORT 11113T1328-5
(a)015T1847-5RIB SUPPORT 11113T1328-7
(a)113T1329-93RIB SUPPORT 21113T1329-1
(a)113T1329-95RIB SUPPORT 21113T1329-3
(a)113T1329-97RIB SUPPORT 21113T1329-5
(a)113T1329-94RIB SUPPORT 71113T1329-2
(a)113T1329-96RIB SUPPORT 71113T1329-4
(a)113T1329-98RIB SUPPORT 71113T1329-6
(a)015T1847-8RIB SUPPORT 81113T1328-4
(a)015T1847-4RIB SUPPORT 81113T1328-6
(a)015T1847-6RIB SUPPORT 81113T1328-8
(a) This is the new rib support part number after the bearing replacement is done in accordance
with this service bulletin.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 12, 2013
767-27A0227
33 of 78
BOEING SERVICE BULLETIN 767-27A0227
ALERTALERT

### Page 34

Group 2:
NotesNew Part NumberNameQTYExisting Part
Number
(a)113T1328-105RIB SUPPORT 11113T1328-99
(a)113T1329-97RIB SUPPORT 21113T1329-5
(a)113T1329-98RIB SUPPORT 71113T1329-6
(a)113T1328-106RIB SUPPORT 81113T1328-100
(a) This is the new rib support part number after the bearing replacement is done in accordance
with this service bulletin.
Group 3:
NotesNew Part NumberNameQTYExisting Part
Number
(a)015T1847-7RIB SUPPORT 11113T1328-1
(a)015T1847-9RIB SUPPORT 11113T1345-133
(a)113T1329-93RIB SUPPORT 21113T1329-1
(a)015T1847-10RIB SUPPORT 21113T1345-131
(a)015T1847-13RIB SUPPORT 21113T1345-135
(a)015T1847-15RIB SUPPORT 21113T1345-187
(a)015T1847-17RIB SUPPORT 21113T1345-259
(a)113T1329-94RIB SUPPORT 71113T1329-2
(a)015T1847-11RIB SUPPORT 71113T1345-132
(a)015T1847-14RIB SUPPORT 71113T1345-136
(a)015T1847-16RIB SUPPORT 71113T1345-188
(a)015T1847-18RIB SUPPORT 71113T1345-260
(a)015T1847-19RIB SUPPORT 81113T1328-2
(a)015T1847-8RIB SUPPORT 81113T1328-4
(a)015T1847-12RIB SUPPORT 81113T1345-134
(a) This is the new rib support part number after the bearing replacement is done in accordance
with this service bulletin.
4. Parts Removed and Not Replaced
None.
D. Parts Necessary to Change Spares
None.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 12, 2013
767-27A0227
34 of 78
BOEING SERVICE BULLETIN 767-27A0227
ALERTALERT

### Page 35

E. Special Tooling - Price and Availability
None.
F. Special Tooling Necessary to do this Service Bulletin
No special tools or equipment are necessary to do the change in this service bulletin. But, maintenance
and overhaul tools in the manuals given in Paragraph 1.J., References, can be necessary. Examine
operator tool supply to make sure all necessary tools are available.
Refer to Boeing drawing number 0A-27128 'REMOVAL/INSTALLATION EQPT - OUTBOARD FLAP
ACTUATOR, CRANK ARM MECHANISM'.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 12, 2013
767-27A0227
35 of 78
BOEING SERVICE BULLETIN 767-27A0227
ALERTALERT

### Page 36

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 12, 2013
767-27A0227
36 of 78
BOEING SERVICE BULLETIN 767-27A0227
ALERTALERT
BLANK PAGE

### Page 37

3.    ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL INFORMATION
CAUTION: KEEP THE WORK AREA, WIRES AND ELECTRICAL BUNDLES CLEAN OF METAL
PARTICLES OR CONTAMINATION WHEN YOU USE TOOLS. UNWANTED MATERIAL,
METAL PARTICLES OR CONTAMINATION CAUGHT IN WIRE BUNDLES CAN CAUSE
DAMAGE TO THE BUNDLES. DAMAGED WIRE BUNDLES CAN CAUSE SPARKS OR
OTHER ELECTRICAL DAMAGE.
NOTE: 1. Manual titles are referred to by acronyms. Refer to Paragraph 1.J., References, for
definition of the acronyms.
2. Obey all of the warnings and cautions given in the specified manual sections.
3. Unless shown differently, these dimensions and tolerances are used:
– Linear dimensions are in inches
– Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus
or minus 0.03 inch
– Tolerance on rivet and bolt edge margin is plus or minus 0.05 inch
– Angular tolerance is plus or minus 2 degrees
– Hole dimensions for standard solid rivets and fasteners are in Structural Repair
Manual (SRM) Chapter 51
– Torque limits to tighten nuts and bolts are in SRM Chapter 51
4. Use the approved fastener and process material substitutions in accordance with
SRM Chapter 51.
5. If the length of any fastener specified in this service bulletin does not meet installation
standards given in SRM Chapter 51, then a fastener of the same specification, or
an approved substitute, with a length which meets the installation standards given
in SRM Chapter 51 may be used. In addition, washers may be installed for fastener
grip length in accordance with SRM Chapter 51.
6. A General Visual Inspection is defined as: A visual examination of an interior or
exterior area, installation or assembly to detect obvious damage, failure or irregularity.
This level of inspection is made from within touching distance unless otherwise
specified. A mirror may be necessary to enhance visual access to all exposed surfaces
in the inspection area. This level of inspection is made under normally available
lighting conditions such as daylight, hangar lighting, flashlight or drop-light and may
require removal or opening of access panels or doors. Stands, ladders or platforms
may be required to gain proximity to the area being checked.
7. These work instructions refer to procedures included in other Boeing documents.
When the words "refer to" are used and the operator has an accepted alternative
procedure, the accepted alternative procedure can be used. When the words "in
accordance with" are included in the instruction, the procedure in the Boeing document
must be used.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 12, 2013
767-27A0227
37 of 78
BOEING SERVICE BULLETIN 767-27A0227
ALERTALERT

### Page 38

8. Boeing Service Letter 767-SL-51-036, Damage Reporting and Repair Plan/Design
Guidelines, is an acceptable procedure to request information from Boeing for
additional structural repair instructions. The Service Letter describes what information
must be provided to Boeing before a structural repair can be provided.
9. Refer to APPENDIX A for guidance to find if the TE rotary actuator(s) at Flap Positions
1, 2, 7, or 8 are serviceable or if they need to be overhauled or replaced.
10. The instructions in Paragraph 3.B., Work Instructions and the figures can include
operation of tools or test equipment. Boeing Engineering Tool Drawings, the Illustrated
Tool and Equipment Manual, and the Special Tool and Ground Handling Drawing
Index contain data on versions of the tools or test equipment that you can use. It is
permitted to use replaced tools. It is not permitted to use superseded tools.
11. If it is necessary to remove more parts for access, you can remove those parts. If
you can get access without removing identified parts, it is not necessary to remove
all of the identified parts. Jacking and shoring limitations must be observed.
12. Where the work instructions include installation of a kept part, a new or serviceable
part with the same part number can be installed as an alternative to the kept part.
13. This service bulletin includes functional test procedures for the systems changed by
this service bulletin. More functional tests can possibly be necessary in accordance
with standard maintenance practices because of interruption to other airplane systems.
14. Boeing tool kit drawing 0A-27128 provides dimensions and information for fabricating
the recommended tools to accomplish the service bulletin work instructions.
B. WORK INSTRUCTIONS
Group 2, Configuration 1:
No further action required.
Group 1-3, Configuration 2:
PREPARE ACCESS TO DO PART 1A OF THIS SERVICE BULLETIN ACCOMPLISHMENT
INSTRUCTIONS:
1. Make sure downlocks are installed on the nose and main landing gear. Refer to 767 AMM 32-00-20
as an accepted procedure.
WARNING: THE DOORS OPEN AND CLOSE QUICKLY AND CAN CAUSE INJURY TO PERSONS
OR DAMAGE TO EQUIPMENT.
2. Open the doors for the landing gear and install the door locks. Refer to 767 AMM 32-00-15 as an
accepted procedure.
3. Supply electrical power. Refer to 767 AMM 24-22-00 as an accepted procedure.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 12, 2013
767-27A0227
38 of 78
BOEING SERVICE BULLETIN 767-27A0227
ALERTALERT

### Page 39

WARNING: KEEP PERSONS AND EQUIPMENT AWAY FROM ALL CONTROL SURFACES AND
THE WHEEL WELLS WHEN HYDRAULIC POWER IS SUPPLIED. AILERONS,
ELEVATORS, RUDDER, SLATS, SPOILERS, AND STABILIZERS ARE FULLY
POWERED SURFACES. WHEN YOU MOVE THE FLAP CONTROL LEVER WITH THE
HYDRAULIC SYSTEM PRESSURISED, THE FLAPS AND FLAP DRIVE MECHANISMS
WILL MOVE QUICKLY. INJURY TO PERSONS OR DAMAGE TO EQUIPMENT CAN
OCCUR WHEN HYDRAULIC POWER IS SUPPLIED.
WARNING: MAKE SURE THE ACESS DOOR FOR THE ENGINER STRUT, THE INBOARD FAN
COWLING, AND THE THRUST REVERSER COWLING ARE CLEAR FROM THE
MOVEMENT OF THE SLATS. IF THE MOVEMENT OF THE SLATS IS BLOCKED, IT
CAN CAUSE DAMAGE TO THE AIRPLANE
4. Pressurize the center hydraulic system and reservoir. Refer to 767 AMM 29-11-00 as an accepted
procedure.
5. Move the Flap control lever to the 5-unit detent and permit the Flaps and slats to move to position.
NOTE: Flaps should remain at the 5-unit detent for the inspection or replacement of the TE Flap
support rib bearings. The Airplane Maintenance Manual (AMM) procedures for removal
and installation of components may be accomplished with the Flaps at the 5-unit detent,
instead of Flaps at the 30-unit detent. The Flaps at the 5-unit detent allow access for
disconnecting the Outboard Flap Actuator Crank Arm Mechanism from the 5 - 8 link,
accomplished by removing the pins at Joint 5 of the Flap linkage mechanism.
6. Deactivate the Trailing Edge Flap. Refer to 767 AMM 27-51-00 as an accepted procedure.
Group 1-3, Configuration 2:
PART 1A: INSPECT THE TE FLAP SUPPORT BEARINGS AT THE TE FLAP SUPPORT RIB
ASSEMBLY IN FLAP POSITIONS 1, 2, 7, AND 8
1. Get access to the Trailing Edge (TE) Flap support rib assembly for Flap Positions 1, 2, 7 and 8 by
removing access panels 561JB, 561HB, 561GB on the lower surface of the wing trailing edge.
Refer to 767 AMM 06-44-00.
2. Remove the applicable TE rotary actuators. Refer to 767 AMM 27-51-22 as an accepted procedure.
NOTE: Keep the actuator attach bolts in the retainers.
3. Remove the applicable TE position transmitters. Refer to 767 AMM 27-51-45 as an accepted
procedure.
4. Do a General Visual Inspection (GVI) of each exposed face of the TE Flap support rib bearings
at the TE Flap support rib assembly in Flap Positions 1, 2, 7 and 8 to determine if the bearings
have a roller retention feature:
CONDITION 1: TWO BEARINGS WITH A ROLLER RETENTION FEATURE ARE INSTALLED
AT TE FLAP SUPPORT RIB ASSEMBLY IN TE FLAP POSITION 1, 2, 7, or 8
a. Confirm that both TE Flap support bearings at the applicable TE Flap support rib assembly
have a retention feature with an inner race roller retainer. Refer to FIGURE 1 and FIGURE 2
as an accepted procedure.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 12, 2013
767-27A0227
39 of 78
BOEING SERVICE BULLETIN 767-27A0227
ALERTALERT

### Page 40

NOTE: If visible, bearings with a roller retention feature can also be identified by the vendor
(McGill) part number, SB-1131. Also, McGill bearings have a single roller
configuration, with 40 rollers in total.
b. Restore the applicable TE Flap support rib assembly in Flap Position(s) 1, 2, 7 or 8. Refer to
FIGURE 3 as an accepted procedure to restore the outboard side of each support rib assembly.
Refer to FIGURE 4 as an accepted procedure to restore the inboard side of each support rib
assembly.
NOTE: If both bearings installed at a TE Flap support rib assembly in Flap Position(s) 1, 2,
7 or 8 have a roller retention feature, the bearings at the applicable Position do not
need to be replaced.
c. Put the airplane back to a serviceable condition. Refer to Part 1B of this service bulletin
accomplishment instructions as an accepted procedure.
CONDITION 2: AT LEAST ONE BEARING WITHOUT A ROLLER RETENTION FEATURE IS
INSTALLED AT TE FLAP SUPPORT RIB ASSEMBLY IN TE FLAP POSITION 1, 2, 7, or 8
a. Confirm that at least one of the two TE Flap support bearings installed at the applicable TE
Flap support rib assembly does not have a roller retention feature. Refer to FIGURE 1 and
FIGURE 2 as an accepted procedure.
NOTE: Bearings that do not have a retention feature have a double roller configuration with
57 rollers per bearing face for a total of 114 rollers, and a roller spacer between roller
sides. The vendor (Rexnord) part number for these bearings is DAT72-90A1-501.
b. If at least one of the two bearings installed at the TE Flap support rib assembly in Flap
Position(s) 1, 2, 7 or 8 does not have a roller retention feature, replace both bearings at the
at the applicable TE Flap support rib assembly in accordance with PART 2 of this service
bulletin accomplishments instructions.
Group 1-3, Configuration 2:
PART 1B: PUT THE AIRPLANE BACK TO A SERVICEABLE CONDITION
1. Install the applicable TE position transmitters. Refer to 767 AMM 27-51-45 as an accepted
procedure.
2. Install the applicable TE rotary actuators. Refer to 767 AMM 27-51-22 as an accepted procedure.
3. Install the applicable access panels at the lower surface of the wing trailing edge. Refer to 767
AMM 06-44-00 as an accepted procedure.
4. Activate the Trailing Edge Flap. Refer to 767 AMM 27-51-00 as an accepted procedure.
5. Remove electrical power, if it is not necessary. Refer to 767 AMM 24-22-00 as an accepted
procedure.
6. Put the airplane back to a serviceable condition.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 12, 2013
767-27A0227
40 of 78
BOEING SERVICE BULLETIN 767-27A0227
ALERTALERT

### Page 41

Group 1-3, Configuration 2:
PART 2: REPLACE THE TE FLAP SUPPORT BEARINGS AR THE TE FLAP SUPPORT RIB
ASSEMBLY IN FLAP POSITIONS 1, 2, 7, AND 8
1. If the inspection in PART 1A of the TE Flap support bearings at the TE Flap support rib assembly
in Flap Position 1 found at least one bearing without a roller retention feature, replace the TE Flap
support rib bearings at actuator support rib in Position 1:
a. Remove the applicable Outboard Flap Actuator Crank Arm Mechanism. Refer to 767 AMM
27-51-21 as an accepted procedure.
b. Get access to the bearings at the TE Flap support rib assembly in Flap Position 1. Refer to
FIGURE 5 as an accepted procedure.
c. Replace both bearings at the TE Flap support rib assembly. Refer to FIGURE 5 as an accepted
procedure.
d. Do a General Visual Inspection (GVI) of the removed TE Flap support bearings and look for
bearing damage.
NOTE: Bearing damage can be detected by finding one or more of the following conditions:
— Migrated or missing rollers in the bearing face. A migrated roller is a loose roller
that has partially moved or shifted horizontally out of the bearing race but is still
part of the bearing assembly. A missing roller can be detected by an empty roller
slot in the roller race or by counting the rollers in the exposed bearing face; there
should be a total of 57 rollers in each Rexnord bearing face.
— Damage on the bearing race, metal wear debris in the bearing and in the bearing
grease, and bearing abrasion on the bearing face. Detecting damage on the
bearing cage or the bearing race includes finding a bent, broken, cracked,
indented, spalled, fractured, brinelled, nicked, burred, eroded, or deformed
bearing race. Also, rollers grinding each other or the bearing race or spacer can
create metal wear filings, debris, flakes, or splinters inside and around the
bearing, leading to bearing abrasion or other damage conditions.
(1) Record the condition of the removed TE Flap support bearings. Refer to APPENDIX A
for the accepted bearing damage definitions and a suggested worksheet to record the
condition of the removed bearings.
NOTE: Damage of the TE support rib bearings can result in the introduction of side
loading into the associated TE rotary actuator, compromising it. Overhaul or
replacement of the applicable TE rotary actuator may be required depending
on the condition of the removed bearings.
e. Find if the TE rotary actuators at Flap Position 1 is serviceable or if it needs to be overhauled
or replaced. Refer to APPENDIX A for the accepted bearing damage definitions.
CONDITION 1: Both bearings at the TE Flap support rib assembly have at least one
face each that meets the definitions of good or slightly damaged bearing face
(1) If there is at least one good or slightly damaged bearing face in each bearing at the TE
Flap support rib assembly in Flap Position 1, the TE rotary actuator is acceptable and
may be used as-is.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 12, 2013
767-27A0227
41 of 78
BOEING SERVICE BULLETIN 767-27A0227
ALERTALERT

### Page 42

(2) Install the Outboard Flap Actuator Crank Arm Mechanism. Refer to 767 AMM 27-51-21
as an accepted procedure.
NOTE: As part of the installation of the Outboard Flap Actuator Crank Arm Mechanism,
the instructions include steps to restore the TE Flap support rib assembly and
reinstall the TE position transmitter and the torque tube.
CONDITION 2: Only one bearing at the TE Flap support rib assembly has at least one
face that meets the definition of good or slightly damaged bearing face. The other
bearing at the same TE Flap support rib assembly has faces that meet the definitions
of moderately damaged or fractured bearing face
(1) If there is at least one good or slightly damaged bearing face in only one bearing at the
TE Flap support rib in Flap Position 1, do one of the two options:
OPTION 1: Overhaul the TE Rotary Actuator
(a) Overhaul the removed TE rotary actuator in accordance with CMM 27-51-10 or CMM
27-51-49.
NOTE: The removed TE rotary actuator cannot be returned to service unless a
complete disassembly of the unit, a Non-Destructive Inspection (NDI) of all
components, check all rotary actuator parts, repair, if necessary, clean,
reassemble the unit, and test, are completed in accordance with CMM
27-51-10 or CMM 27-51-49.
(b) Install the Outboard Flap Actuator Crank Arm Mechanism. Refer to 767 AMM 27-51-21
as an accepted procedure.
NOTE: As part of the installation instructions for the Outboard Flap Actuator Crank
Arm Mechanism, reinstall the overhauled TE rotary actuator.
Also as part of the installation of the Outboard Flap Actuator Crank Arm
Mechanism, the instructions include steps restore the TE Flap support rib
assembly and reinstall the TE position transmitter and the torque tube.
OPTION 2: Replace the TE Rotary Actuator
(a) Get a serviceable replacement for the removed TE rotary actuator.
NOTE: The removed TE rotary actuator cannot be returned to service unless a
complete disassembly of the unit, a Non-Destructive Inspection (NDI) of all
components, check all rotary actuator parts, repair, if necessary, clean,
reassemble the unit, and test, are completed in accordance with CMM
27-51-10 or CMM 27-51-49
A serviceable replacement for the removed TE rotary actuator can be a
new or overhauled unit that is in serviceable condition.
(b) Install the Outboard Flap Actuator Crank Arm Mechanism. Refer to 767 AMM 27-51-21
as an accepted procedure.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 12, 2013
767-27A0227
42 of 78
BOEING SERVICE BULLETIN 767-27A0227
ALERTALERT

### Page 43

NOTE: As part of the installation instructions for the Outboard Flap Actuator Crank
Arm Mechanism, install an overhauled or new TE rotary actuator.
Also as part of the installation of the Outboard Flap Actuator Crank Arm
Mechanism, the instructions include steps restore the TE Flap support rib
assembly and reinstall the TE position transmitter and the torque tube.
CONDITION 3: Both bearings at the TE Flap support rib assembly have all faces that
meet the definitions of moderately damaged or fractured bearing face
(1) Get a serviceable replacement for the removed TE rotary actuator if the GVI finds that
there are two moderately damaged or fractured bearing faces in each bearing at the TE
Flap support rib assembly in Flap Position 1.
NOTE: A serviceable replacement for the removed TE rotary actuator can be a new or
overhauled unit that is in serviceable condition.
(2) Discard the removed TE rotary actuator.
(3) Install the Outboard Flap Actuator Crank Arm Mechanism. Refer to 767 AMM 27-51-21
as an accepted procedure.
NOTE: As part of the installation instructions for the Outboard Flap Actuator Crank Arm
Mechanism, install an overhauled or new TE rotary actuator.
Also as part of the installation of the Outboard Flap Actuator Crank Arm
Mechanism, the instructions include steps restore the TE Flap support rib
assembly and reinstall the TE position transmitter and the torque tube.
2. If the inspection in PART 1A of the TE Flap support bearings at the TE Flap support rib assembly
in Flap Position 2 found at least one bearing without a roller retention feature, replace the TE Flap
support rib bearings at actuator support rib in Position 2:
a. Remove the applicable Outboard Flap Actuator Crank Arm Mechanism. Refer to 767 AMM
27-51-21 as an accepted procedure.
b. Get access to the bearings at the TE Flap support rib assembly in Flap Position 2. Refer to
FIGURE 6.
c. Replace both bearings at the TE Flap support rib assembly. Refer to FIGURE 6.
d. Do a General Visual Inspection (GVI) of the removed TE Flap support bearings and look for
bearing damage.
NOTE: Bearing damage can be detected by finding one or more of the following conditions:
— Migrated or missing rollers in the bearing face. A migrated roller is a loose roller
that has partially moved or shifted horizontally out of the bearing race but is still
part of the bearing assembly. A missing roller can be detected by an empty roller
slot in the roller race or by counting the rollers in the exposed bearing face; there
should be a total of 57 rollers in each Rexnord bearing face.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 12, 2013
767-27A0227
43 of 78
BOEING SERVICE BULLETIN 767-27A0227
ALERTALERT

### Page 44

— Damage on the bearing race, metal wear debris in the bearing and in the bearing
grease, and bearing abrasion on the bearing face. Detecting damage on the
bearing cage or the bearing race includes finding a bent, broken, cracked,
indented, spalled, fractured, brinelled, nicked, burred, eroded, or deformed
bearing race. Also, rollers grinding each other or the bearing race or spacer can
create metal wear filings, debris, flakes, or splinters inside and around the
bearing, leading to bearing abrasion or other damage conditions.
(1) Record the condition of the removed TE Flap support bearings. Refer to APPENDIX A
for the accepted bearing damage definitions and a suggested worksheet to record the
condition of the removed bearings.
NOTE: Damage of the TE support rib bearings can result in the introduction of side
loading into the associated TE rotary actuator, compromising it. Overhaul or
replacement of the applicable TE rotary actuator may be required depending
on the condition of the removed bearings.
e. Find if the TE rotary actuators at Flap Position 2 is serviceable or if it needs to be overhauled
or replaced. Refer to APPENDIX A for the accepted bearing damage definitions.
CONDITION 1: Both bearings at the TE Flap support rib assembly have at least one
face each that meets the definitions of good or slightly damaged bearing face
(1) If there is at least one good or slightly damaged bearing face in each bearing at the TE
Flap support rib assembly in Flap Position 2, the TE rotary actuator is acceptable and
may be used as-is.
(2) Install the Outboard Flap Actuator Crank Arm Mechanism. Refer to 767 AMM 27-51-21
as an accepted procedure.
NOTE: As part of the installation of the Outboard Flap Actuator Crank Arm Mechanism,
the instructions include steps to restore the TE Flap support rib assembly and
reinstall the TE position transmitter and the torque tube.
CONDITION 2: Only one bearing at the TE Flap support rib assembly has at least one
face that meets the definition of good or slightly damaged bearing face. The other
bearing at the same TE Flap support rib assembly has faces that meet the definitions
of moderately damaged or fractured bearing face
(1) If there is at least one good or slightly damaged bearing face in only one bearing at the
TE Flap support rib in Flap Position 2, do one of the two options:
OPTION 1: Overhaul the TE Rotary Actuator
(a) Overhaul the TE rotary actuator in accordance with CMM 27-51-10 or CMM 27-51-49.
NOTE: The removed TE rotary actuator cannot be returned to service unless a
complete disassembly of the unit, a Non-Destructive Inspection (NDI) of all
components, check all rotary actuator parts, repair, if necessary, clean,
reassemble the unit, and test, are completed in accordance with CMM
27-51-10 or CMM 27-51-49.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 12, 2013
767-27A0227
44 of 78
BOEING SERVICE BULLETIN 767-27A0227
ALERTALERT

### Page 45

(b) Install the Outboard Flap Actuator Crank Arm Mechanism. Refer to 767 AMM 27-51-21
as an accepted procedure.
NOTE: As part of the installation instructions for the Outboard Flap Actuator Crank
Arm Mechanism, reinstall the overhauled TE rotary actuator.
Also as part of the installation of the Outboard Flap Actuator Crank Arm
Mechanism, the instructions include steps restore the TE Flap support rib
assembly and reinstall the TE position transmitter and the torque tube.
OPTION 2: Replace the TE Rotary Actuator
(a) Get a serviceable replacement for the removed TE rotary actuator.
NOTE: The removed TE rotary actuator cannot be returned to service unless a
complete disassembly of the unit, a Non-Destructive Inspection (NDI) of all
components, check all rotary actuator parts, repair, if necessary, clean,
reassemble the unit, and test, are completed in accordance with CMM
27-51-10 or CMM 27-51-49
A serviceable replacement for the removed TE rotary actuator can be a
new or overhauled unit that is in serviceable condition.
(b) Install the Outboard Flap Actuator Crank Arm Mechanism. Refer to 767 AMM 27-51-21
as an accepted procedure.
NOTE: As part of the installation instructions for the Outboard Flap Actuator Crank
Arm Mechanism, install an overhauled or new TE rotary actuator.
Also as part of the installation of the Outboard Flap Actuator Crank Arm
Mechanism, the instructions include steps restore the TE Flap support rib
assembly and reinstall the TE position transmitter and the torque tube.
CONDITION 3: Both bearings at the TE Flap support rib assembly have all faces that
meet the definitions of moderately damaged or fractured bearing face
(1) Get a serviceable replacement for the removed TE rotary actuator if the GVI finds that
there are two moderately damaged or fractured bearing faces in each bearing at the TE
Flap support rib assembly in Flap Position 2.
NOTE: A serviceable replacement for the removed TE rotary actuator can be a new or
overhauled unit that is in serviceable condition.
(2) Discard the removed TE rotary actuator.
(3) Install the Outboard Flap Actuator Crank Arm Mechanism. Refer to 767 AMM 27-51-21
as an accepted procedure.
NOTE: As part of the installation instructions for the Outboard Flap Actuator Crank Arm
Mechanism, install an overhauled or new TE rotary actuator.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 12, 2013
767-27A0227
45 of 78
BOEING SERVICE BULLETIN 767-27A0227
ALERTALERT

### Page 46

Also as part of the installation of the Outboard Flap Actuator Crank Arm
Mechanism, the instructions include steps restore the TE Flap support rib
assembly and reinstall the TE position transmitter and the torque tube.
3. If the inspection in PART 1A of the TE Flap support bearings at the TE Flap support rib assembly
in Flap Position 7 found at least one bearing without a roller retention feature, replace the TE Flap
support rib bearings at actuator support rib in Position 7:
a. Remove the applicable Outboard Flap Actuator Crank Arm Mechanism. Refer to 767 AMM
27-51-21 as an accepted procedure.
b. Get access to the bearings at the TE Flap support rib assembly in Flap Position 7. Refer to
FIGURE 7.
c. Replace both bearings at the TE Flap support rib assembly. Refer to FIGURE 7.
d. Do a General Visual Inspection (GVI) of the removed TE Flap support bearings and look for
bearing damage.
NOTE: Bearing damage can be detected by finding one or more of the following conditions:
— Migrated or missing rollers in the bearing face. A migrated roller is a loose roller
that has partially moved or shifted horizontally out of the bearing race but is still
part of the bearing assembly. A missing roller can be detected by an empty roller
slot in the roller race or by counting the rollers in the exposed bearing face; there
should be a total of 57 rollers in each Rexnord bearing face.
— Damage on the bearing race, metal wear debris in the bearing and in the bearing
grease, and bearing abrasion on the bearing face. Detecting damage on the
bearing cage or the bearing race includes finding a bent, broken, cracked,
indented, spalled, fractured, brinelled, nicked, burred, eroded, or deformed
bearing race. Also, rollers grinding each other or the bearing race or spacer can
create metal wear filings, debris, flakes, or splinters inside and around the
bearing, leading to bearing abrasion or other damage conditions.
(1) Record the condition of the removed TE Flap support bearings. Refer to APPENDIX A
for the accepted bearing damage definitions and a suggested worksheet to record the
condition of the removed bearings.
NOTE: Damage of the TE support rib bearings can result in the introduction of side
loading into the associated TE rotary actuator, compromising it. Overhaul or
replacement of the applicable TE rotary actuator may be required depending
on the condition of the removed bearings.
e. Find if the TE rotary actuators at Flap Position 7 is serviceable or if it needs to be overhauled
or replaced. Refer to APPENDIX A for the accepted bearing damage definitions.
CONDITION 1: Both bearings at the TE Flap support rib assembly have at least one
face each that meets the definitions of good or slightly damaged bearing face
(1) If there is at least one good or slightly damaged bearing face in each bearing at the TE
Flap support rib assembly in Flap Position 7, the TE rotary actuator is acceptable and
may be used as-is.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 12, 2013
767-27A0227
46 of 78
BOEING SERVICE BULLETIN 767-27A0227
ALERTALERT

### Page 47

(2) Install the Outboard Flap Actuator Crank Arm Mechanism. Refer to 767 AMM 27-51-21
as an accepted procedure.
NOTE: As part of the installation of the Outboard Flap Actuator Crank Arm Mechanism,
the instructions include steps to restore the TE Flap support rib assembly and
reinstall the TE position transmitter and the torque tube.
CONDITION 2: Only one bearing at the TE Flap support rib assembly has at least one
face that meets the definition of good or slightly damaged bearing face. The other
bearing at the same TE Flap support rib assembly has faces that meet the definitions
of moderately damaged or fractured bearing face
(1) If there is at least one good or slightly damaged bearing face in only one bearing at the
TE Flap support rib in Flap Position 7, do one of the two options:
OPTION 1: Overhaul the TE Rotary Actuator
(a) Overhaul the TE rotary actuator in accordance with CMM 27-51-10 or CMM 27-51-49.
NOTE: The removed TE rotary actuator cannot be returned to service unless a
complete disassembly of the unit, a Non-Destructive Inspection (NDI) of all
components, check all rotary actuator parts, repair, if necessary, clean,
reassemble the unit, and test, are completed in accordance with CMM
27-51-10 or CMM 27-51-49.
(b) Install the Outboard Flap Actuator Crank Arm Mechanism. Refer to 767 AMM 27-51-21
as an accepted procedure.
NOTE: As part of the installation instructions for the Outboard Flap Actuator Crank
Arm Mechanism, reinstall the overhauled TE rotary actuator.
Also as part of the installation of the Outboard Flap Actuator Crank Arm
Mechanism, the instructions include steps restore the TE Flap support rib
assembly and reinstall the TE position transmitter and the torque tube.
OPTION 2: Replace the TE Rotary Actuator
(a) Get a serviceable replacement for the removed TE rotary actuator.
NOTE: The removed TE rotary actuator cannot be returned to service unless a
complete disassembly of the unit, a Non-Destructive Inspection (NDI) of all
components, check all rotary actuator parts, repair, if necessary, clean,
reassemble the unit, and test, are completed in accordance with CMM
27-51-10 or CMM 27-51-49
A serviceable replacement for the removed TE rotary actuator can be a
new or overhauled unit that is in serviceable condition.
(b) Install the Outboard Flap Actuator Crank Arm Mechanism. Refer to 767 AMM 27-51-21
as an accepted procedure.
NOTE: As part of the installation instructions for the Outboard Flap Actuator Crank
Arm Mechanism, install an overhauled or new TE rotary actuator.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 12, 2013
767-27A0227
47 of 78
BOEING SERVICE BULLETIN 767-27A0227
ALERTALERT

### Page 48

Also as part of the installation of the Outboard Flap Actuator Crank Arm
Mechanism, the instructions include steps restore the TE Flap support rib
assembly and reinstall the TE position transmitter and the torque tube.
CONDITION 3: Both bearings at the TE Flap support rib assembly have all faces that
meet the definitions of moderately damaged or fractured bearing face
(1) Get a serviceable replacement for the removed TE rotary actuator if the GVI finds that
there are two moderately damaged or fractured bearing faces in each bearing at the TE
Flap support rib assembly in Flap Position 7.
NOTE: A serviceable replacement for the removed TE rotary actuator can be a new or
overhauled unit that is in serviceable condition.
(2) Discard the removed TE rotary actuator.
(3) Install the Outboard Flap Actuator Crank Arm Mechanism. Refer to 767 AMM 27-51-21
as an accepted procedure.
NOTE: As part of the installation instructions for the Outboard Flap Actuator Crank Arm
Mechanism, install an overhauled or new TE rotary actuator.
Also as part of the installation of the Outboard Flap Actuator Crank Arm
Mechanism, the instructions include steps restore the TE Flap support rib
assembly and reinstall the TE position transmitter and the torque tube.
4. If the inspection in PART 1A of the TE Flap support bearings at the TE Flap support rib assembly
in Flap Position 8 found at least one bearing without a roller retention feature, replace the TE Flap
support rib bearings at actuator support rib in Position 8:
a. Remove the applicable Outboard Flap Actuator Crank Arm Mechanism. Refer to 767 AMM
27-51-21 as an accepted procedure.
b. Get access to the bearings at the TE Flap support rib assembly in Flap Position 8. Refer to
FIGURE 8.
c. Replace both bearings at the TE Flap support rib assembly. Refer to FIGURE 8.
d. Do a General Visual Inspection (GVI) of the removed TE Flap support bearings and look for
bearing damage.
NOTE: Bearing damage can be detected by finding one or more of the following conditions:
— Migrated or missing rollers in the bearing face. A migrated roller is a loose roller
that has partially moved or shifted horizontally out of the bearing race but is still
part of the bearing assembly. A missing roller can be detected by an empty roller
slot in the roller race or by counting the rollers in the exposed bearing face; there
should be a total of 57 rollers in each Rexnord bearing face.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 12, 2013
767-27A0227
48 of 78
BOEING SERVICE BULLETIN 767-27A0227
ALERTALERT

### Page 49

— Damage on the bearing race, metal wear debris in the bearing and in the bearing
grease, and bearing abrasion on the bearing face. Detecting damage on the
bearing cage or the bearing race includes finding a bent, broken, cracked,
indented, spalled, fractured, brinelled, nicked, burred, eroded, or deformed
bearing race. Also, rollers grinding each other or the bearing race or spacer can
create metal wear filings, debris, flakes, or splinters inside and around the
bearing, leading to bearing abrasion or other damage conditions.
(1) Record the condition of the removed TE Flap support bearings. Refer to APPENDIX A
for the accepted bearing damage definitions and a suggested worksheet to record the
condition of the removed bearings.
NOTE: Damage of the TE support rib bearings can result in the introduction of side
loading into the associated TE rotary actuator, compromising it. Overhaul or
replacement of the applicable TE rotary actuator may be required depending
on the condition of the removed bearings.
e. Find if the TE rotary actuators at Flap Position 8 is serviceable or if it needs to be overhauled
or replaced. Refer to APPENDIX A for the accepted bearing damage definitions.
CONDITION 1: Both bearings at the TE Flap support rib assembly have at least one
face each that meets the definitions of good or slightly damaged bearing face
(1) If there is at least one good or slightly damaged bearing face in each bearing at the TE
Flap support rib assembly in Flap Position 8, the TE rotary actuator is acceptable and
may be used as-is.
(2) Install the Outboard Flap Actuator Crank Arm Mechanism. Refer to 767 AMM 27-51-21
as an accepted procedure.
NOTE: As part of the installation of the Outboard Flap Actuator Crank Arm Mechanism,
the instructions include steps to restore the TE Flap support rib assembly and
reinstall the TE position transmitter and the torque tube.
CONDITION 2: Only one bearing at the TE Flap support rib assembly has at least one
face that meets the definition of good or slightly damaged bearing face. The other
bearing at the same TE Flap support rib assembly has faces that meet the definitions
of moderately damaged or fractured bearing face
(1) If there is at least one good or slightly damaged bearing face in only one bearing at the
TE Flap support rib in Flap Position 8, do one of the two options:
OPTION 1: Overhaul the TE Rotary Actuator
(a) Overhaul the TE rotary actuator in accordance with CMM 27-51-10 or CMM 27-51-49.
NOTE: The removed TE rotary actuator cannot be returned to service unless a
complete disassembly of the unit, a Non-Destructive Inspection (NDI) of all
components, check all rotary actuator parts, repair, if necessary, clean,
reassemble the unit, and test, are completed in accordance with CMM
27-51-10 or CMM 27-51-49.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 12, 2013
767-27A0227
49 of 78
BOEING SERVICE BULLETIN 767-27A0227
ALERTALERT

### Page 50

(b) Install the Outboard Flap Actuator Crank Arm Mechanism. Refer to 767 AMM 27-51-21
as an accepted procedure.
NOTE: As part of the installation instructions for the Outboard Flap Actuator Crank
Arm Mechanism, reinstall the overhauled TE rotary actuator.
Also as part of the installation of the Outboard Flap Actuator Crank Arm
Mechanism, the instructions include steps restore the TE Flap support rib
assembly and reinstall the TE position transmitter and the torque tube.
OPTION 2: Replace the TE Rotary Actuator
(a) Get a serviceable replacement for the removed TE rotary actuator.
NOTE: The removed TE rotary actuator cannot be returned to service unless a
complete disassembly of the unit, a Non-Destructive Inspection (NDI) of all
components, check all rotary actuator parts, repair, if necessary, clean,
reassemble the unit, and test, are completed in accordance with CMM
27-51-10 or CMM 27-51-49
A serviceable replacement for the removed TE rotary actuator can be a
new or overhauled unit that is in serviceable condition.
(b) Install the Outboard Flap Actuator Crank Arm Mechanism. Refer to 767 AMM 27-51-21
as an accepted procedure.
NOTE: As part of the installation instructions for the Outboard Flap Actuator Crank
Arm Mechanism, install an overhauled or new TE rotary actuator.
Also as part of the installation of the Outboard Flap Actuator Crank Arm
Mechanism, the instructions include steps restore the TE Flap support rib
assembly and reinstall the TE position transmitter and the torque tube.
CONDITION 3: Both bearings at the TE Flap support rib assembly have all faces that
meet the definitions of moderately damaged or fractured bearing face
(1) Get a serviceable replacement for the removed TE rotary actuator if the GVI finds that
there are two moderately damaged or fractured bearing faces in each bearing at the TE
Flap support rib assembly in Flap Position 8.
NOTE: A serviceable replacement for the removed TE rotary actuator can be a new or
overhauled unit that is in serviceable condition.
(2) Discard the removed TE rotary actuator.
(3) Install the Outboard Flap Actuator Crank Arm Mechanism. Refer to 767 AMM 27-51-21
as an accepted procedure.
NOTE: As part of the installation instructions for the Outboard Flap Actuator Crank Arm
Mechanism, install an overhauled or new TE rotary actuator.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 12, 2013
767-27A0227
50 of 78
BOEING SERVICE BULLETIN 767-27A0227
ALERTALERT

### Page 51

Also as part of the installation of the Outboard Flap Actuator Crank Arm
Mechanism, the instructions include steps restore the TE Flap support rib
assembly and reinstall the TE position transmitter and the torque tube.
5. Install the applicable access panels at the lower surface of the wing trailing edge. Refer to 767
AMM 06-44-00 as an accepted procedure.
6. Remove the applicable spoiler locks. Refer to 767 AMM 27-61-00 as an accepted procedure.
Group 1-3, Configuration 2:
FUNCTIONAL TEST AFTER TE FLAP SUPPORT BEARINGS REPLACEMENT
1. Pressurize the center hydraulic system. Refer to 767 AMM 29-11-00 as an accepted procedure.
2. Operate the Flap control lever through a full cycle and make sure the Flaps operate correctly.
3. Put the airplane back to a serviceable condition.
Group 1, 3, Configuration 1:
PART 3: RE-IDENTIFY THE TRAILING EDGE (TE) FLAP SUPPORT RIB ASSEMBLY FOR
APPLICABLE FLAP POSITIONS WITH CORRECT NEW PART NUMBERS
1. Deactivate Trailing Edge Flap. Refer to 767 AMM 27-51-00 as an accepted procedure.
2. Get access to the Trailing Edge (TE) Flap support rib assembly for Flap Positions 1 and 8 by
removing access panels 561JB, 561HB, 561GB on the lower surface of the wing trailing edge.
Refer to 767 AMM 06-44-00 as an accepted procedure.
3. Group 1, Configuration 1:
Reidentify the TE Flap support rib assembly in Flap Positions 1 and 8 with the correct new part
numbers. Refer to FIGURE 9.
4. Group 3, Configuration 1:
Reidentify the TE Flap support rib assembly in Flap Positions 1, 2, 7 and 8 with the correct new
part numbers. Refer to FIGURE 9.
5. Activate Trailing Edge Flap. Refer to 767 AMM 27-51-00 as an accepted procedure.
6. Remove the power from the center hydraulic system. Refer to 767 AMM 29-11-00 as an accepted
procedure.
7. Remove electrical power. Refer to 767 AMM 24-22-00 as an accepted procedure.
8. Put the airplane back to a serviceable condition.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 12, 2013
767-27A0227
51 of 78
BOEING SERVICE BULLETIN 767-27A0227
ALERTALERT

### Page 52 (OCR)

BOEING SERVICE BULLETIN 767-27A0227
ALERT  ALERT
This Figure applies only to: Group 1-3, Configuration 2.
TRAILING EDGE (TE) FLAP SUPPORT RIB
POSITION 1 SHOWN.
TE FLAP SUPPORT RIB POSITION 8 OPPOSITE.
POSITION 2 AND 7, SIMILAR.
(10 T
SEAL  2193689
FIGURE 1: INSPECT THE TRAILING EDGE FLAP SUPPORT BEARINGS AT THE TE FLAP SUPPORT RIB
ASSEMBLY IN FLAP POSITIONS 1, 2, 7, AND 8, OUTBOARD SIDE
(SHEET 1 OF 3)
Original Issue: February 12, 2013
Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright © Unpublished  767-27A0227
Work - See page 1 for details.  52 of 78

### Page 53

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for each side of the TE Flap support rib.
More DataQtyIdentificationNameTaskStep
(a)2-NutRemove / Keep1
(a)2-WasherRemove / Keep
(a)1-NutRemove / Keep2
(a)1-WasherRemove / Keep
(a)1-Transmitter HousingRemove / Keep3
(a)--Safety lockwireRemove4
(b)1-NutRemove / Keep5
1-WasherRemove / Keep6
(a)6-NutRemove / Keep7
(a)6-WasherRemove / Keep
(a)3-NutRemove / Keep8
(a)3-WasherRemove / Keep
1-Rib DoublerRemove / Keep9
1-BearingLocate10
FIGURE 1: INSPECT THE TRAILING EDGE FLAP SUPPORT BEARINGS AT THE TE FLAP SUPPORT RIB
ASSEMBLY IN FLAP POSITIONS 1, 2, 7, AND 8, OUTBOARD SIDE
(SHEET 2 OF 3)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 12, 2013
767-27A0227
53 of 78
BOEING SERVICE BULLETIN 767-27A0227
ALERTALERT

### Page 54

More DataQtyIdentificationNameTaskStep
carefully, as re-
quired, with a piece
of cloth to get visual
access to bearing
face
--GreaseClean11
Do a General Visual
Inspection (GVI) of
the removed TE
Flap support bear-
ings and look for
bearing type and
possible bearing
damage
1-BearingInspect12
(c)1-Rib DoublerClean13
(a) Make a note or write down the location of removed nuts and washers. During installation, the bolts,
washers, and nuts should be placed in their original locations to prevent any damage.
(b) Refer to 0A-27128 for suggested spanner wrench tool.
(c) Clean off grease and, if present, Mastinox compound. Refer to SOPM 20-30-03.
FIGURE 1: INSPECT THE TRAILING EDGE FLAP SUPPORT BEARINGS AT THE TE FLAP SUPPORT RIB
ASSEMBLY IN FLAP POSITIONS 1, 2, 7, AND 8, OUTBOARD SIDE
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 12, 2013
767-27A0227
54 of 78
BOEING SERVICE BULLETIN 767-27A0227
ALERTALERT

### Page 55 (OCR)

BOEING SERVICE BULLETIN 767-27A0227
ALERT  ALERT
This Figure applies only to: Group 1-3, Configuration 2.
7 LOCATIONS
1
TRAILING EDGE (TE) FLAP SUPPORT RIB
POSITION 1 SHOWN
TE FLAP SUPPORT RIB POSITION 8 OPPOSITE.
POSITION 2 AND 7, SIMILAR.
SEAL  2193712
FIGURE 2: INSPECT THE TRAILING EDGE FLAP SUPPORT BEARINGS AT THE TE FLAP SUPPORT RIB
ASSEMBLY IN FLAP POSITIONS 1, 2, 7, AND 8, INBOARD SIDE
(SHEET 1 OF 3)
Original Issue: February 12, 2013
Export Controlled ECCN: 9E991 - BOEING  767-27A0227
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  55 of 78

### Page 56

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for each side of the TE Flap support rib.
More DataQtyIdentificationNameTaskStep
(a)7-NutRemove / Keep1
(a)7-WasherRemove / Keep
(a)3-NutRemove / Keep2
(a)3-WasherRemove / Keep
(a)3-NutRemove / Keep3
(a)3-WasherRemove / Keep
(a)2-NutRemove / Keep4
(a)2-WasherRemove / Keep
(a)1-NutRemove / Keep5
(a)1-WasherRemove / Keep
1-Reaction RingRemove / Keep6
1-ShimRemove / Keep7
1-BearingLocate8
FIGURE 2: INSPECT THE TRAILING EDGE FLAP SUPPORT BEARINGS AT THE TE FLAP SUPPORT RIB
ASSEMBLY IN FLAP POSITIONS 1, 2, 7, AND 8, INBOARD SIDE
(SHEET 2 OF 3)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 12, 2013
767-27A0227
56 of 78
BOEING SERVICE BULLETIN 767-27A0227
ALERTALERT

### Page 57

More DataQtyIdentificationNameTaskStep
carefully, as re-
quired, with a piece
of cloth to get visual
access to bearing
face
--GreaseClean9
Do a General Visual
Inspection (GVI) of
the removed TE
Flap support bear-
ings and look for
bearing type and
possible bearing
damage
1-BearingInspect10
(b)1-ShimClean11
(b)1-Reaction RingClean
(a) Make a note or write down the location of removed nuts and washers. During installation, the bolts,
washers, and nuts should be placed in their original locations to prevent any damage.
(b) Clean off grease and, if present, Mastinox compound. Refer to SOPM 20-30-03.
FIGURE 2: INSPECT THE TRAILING EDGE FLAP SUPPORT BEARINGS AT THE TE FLAP SUPPORT RIB
ASSEMBLY IN FLAP POSITIONS 1, 2, 7, AND 8, INBOARD SIDE
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 12, 2013
767-27A0227
57 of 78
BOEING SERVICE BULLETIN 767-27A0227
ALERTALERT

### Page 58 (OCR)

BOEING SERVICE BULLETIN 767-27A0227
ALERT  ALERT
This Figure applies only to: Group 1-3, Configuration 2.
TRAILING EDGE (TE) FLAP SUPPORT RIB
POSITION 1 SHOWN.
TE FLAP SUPPORT RIB POSITION 8 OPPOSITE
POSITION 2 AND 7, SIMILAR
2 LOCATIONS
6 LOCATIONS
BEARING
SEAL  2193722
FIGURE 3: RESTORE THE TRAILING EDGE FLAP SUPPORT BEARINGS AT THE TE FLAP SUPPORT RIB
ASSEMBLY IN FLAP POSITIONS 1, 2, 7, AND 8, OUTBOARD SIDE
(SHEET 1 OF 3)
Original Issue: February 12, 2013
Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright © Unpublished  767-27A0227
Work - See page 1 for details.  58 of 78

### Page 59

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for each side of the TE Flap support rib.
More DataQtyIdentificationNameTaskStep
Apply BMS3-33
grease to mating
surface
1-Rib DoublerInstall (Kept)1
Tighten nut to torque
range of 220-410
Inch-Pounds
6-WasherInstall (Kept)2
6-NutInstall (Kept)
3-WasherInstall (Kept)3
Tighten nut to torque
range of 95-105
Inch-Pounds
3-NutInstall (Kept)
1-WasherInstall (Kept)4
Tighten nut to torque
range of 2800-3500
Inch-Pounds
1-NutInstall (Kept)5
(a)
FIGURE 3: RESTORE THE TRAILING EDGE FLAP SUPPORT BEARINGS AT THE TE FLAP SUPPORT RIB
ASSEMBLY IN FLAP POSITIONS 1, 2, 7, AND 8, OUTBOARD SIDE
(SHEET 2 OF 3)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 12, 2013
767-27A0227
59 of 78
BOEING SERVICE BULLETIN 767-27A0227
ALERTALERT

### Page 60

More DataQtyIdentificationNameTaskStep
such that the pigtail
is on top of the bear-
ing retainer nut
-MS20995NC40Safety lockwireInstall (New)6
(c)
1-Transmitter HousingInstall (Kept)7
(b)2-WasherInstall (Kept)8
(b)2-NutInstall (Kept)
Tighten nut to torque
range of 95-105
Inch-Pounds
(b)1-NutInstall (Kept)9
(b)1-WasherInstall (Kept)
Apply grease at this
location until you
see clean grease
come out from the
seal
-BMS3-33GreaseInject10
(a) Refer to 0A-27128 for suggested spanner wrench tool.
(b) Temporarily install fastener. Final installation to be performed with systems installation.
(c) Refer to 767 AMM 20-10-23 as an accepted procedure.
FIGURE 3: RESTORE THE TRAILING EDGE FLAP SUPPORT BEARINGS AT THE TE FLAP SUPPORT RIB
ASSEMBLY IN FLAP POSITIONS 1, 2, 7, AND 8, OUTBOARD SIDE
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 12, 2013
767-27A0227
60 of 78
BOEING SERVICE BULLETIN 767-27A0227
ALERTALERT

The text continues at https://openairdocs.org/service-documents/boeing/767-27a0227/file/573c4ad1bff9.md?from=61

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
