# Boeing Alert Requirements Bulletin 767-32A0253 RB: No revision named

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2024-1689; AD 2024-25-08 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Alert Requirements Bulletin 767-32A0253 RB](https://openairdocs.org/service-documents/boeing/767-32a0253-rb.md)
- Title as filed: 767-32A0253-00 RB
- Pages: 23
- PDF: https://openairdocs.org/files/sha256/d8/07/d8076b5c546852a4c51c949a03c81499eb388e779f4d410bbfb8506dab3eb36a
- Page: https://openairdocs.org/service-documents/boeing/767-32a0253-rb/file/d8076b5c5468

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Commercial 
Airplanes
767
Requirements Bulletin
ALERT
Number: 767-32A0253 RB
Original Issue: February 06, 2024
ATA System: 3211
SUBJECT: LANDING GEAR - Main Landing Gear - Outer Cylinder Inspection and Replacement
EXPORT CONTROLLED - This technology or software is subject to the U.S. Export Administration Regulations
(EAR), (15 C.F.R. Parts 730-774). No authorization from the U.S. Department of Commerce is required for
export, re-export, in-country transfer, or access EXCEPT to country group E:1 or E:2 countries/persons per
Supp.1 to Part 740 of the EAR.
9E991ECCN:
Copyright © 2024 The Boeing Company
Treatment of this document and its content is governed by contract with Boeing. Rights to use this document
are licensed on a per aircraft basis and such rights may not be transferable. For more information, contact The
Boeing Company.
Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner,
BBJ, DC-8, DC-9, DC-10, KC-10, KC-46, KDC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8, Poseidon and
Boeing liveries are all trademarks owned by The Boeing Company; and no trademark license is granted in
connection with this document unless provided in writing by Boeing.
Original Issue: February 06, 2024
767-32A0253 RB
1 of 23
5.0

### Page 2

Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: February 06, 2024
767-32A0253 RB
2 of 23
REQUIREMENTS BULLETIN 767-32A0253
ALERTALERT
BLANK PAGE

### Page 3

Table of Contents
1. EFFECTIVITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
A. Airplanes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
B. Spares Affected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2. CONCURRENT REQUIREMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3. COMPLIANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4. APPROVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
5. ACCOMPLISHMENT INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
A. General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
B. Work Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
FIGURE 1: MAIN LANDING GEAR - OUTER CYLINDER - PART NUMBER AND SERIAL NUMBER
INSPECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
APPENDIX A: AFFECTED OUTER CYLINDER PART NUMBERS AND SERIAL NUMBERS . . . . . . . 18
APPENDIX B: AFFECTED OUTER CYLINDER PART NUMBERS AND SERIAL NUMBERS . . . . . . . 19
APPENDIX C: AFFECTED OUTER CYLINDER PART NUMBERS AND SERIAL NUMBERS . . . . . . . 20
APPENDIX D: MAIN LANDING GEAR - OUTER CYLINDER - INSPECTION FOR HEAT DAMAGE AND
CRACKS, AND REPAIR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: February 06, 2024
767-32A0253 RB
3 of 23
REQUIREMENTS BULLETIN 767-32A0253
ALERTALERT

### Page 4

Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: February 06, 2024
767-32A0253 RB
4 of 23
REQUIREMENTS BULLETIN 767-32A0253
ALERTALERT
BLANK PAGE

### Page 5

Commercial 
Airplanes
767
Requirements Bulletin
ALERT
Number: 767-32A0253 RB
Original Issue: February 06, 2024
ATA System: 3211
SUBJECT: LANDING GEAR - Main Landing Gear - Outer Cylinder Inspection and Replacement
THIS DOCUMENT IS SENT TO THE OPERATORS OF RECORD OF THE AIRPLANES SHOWN IN
PARAGRAPH 1.A., EFFECTIVITY. IF AN AIRPLANE HAS BEEN LEASED OR SOLD, SEND THIS DOCUMENT
TO THE NEW OPERATOR. IF APPLICABLE SPARES HAVE BEEN SOLD, SEND THIS DOCUMENT TO THE
NEW OWNER. THIS IS AN ENHANCED REQUIRED FOR COMPLIANCE DOCUMENT. THE BOEING
PROCESSES USED TO CREATE THE SERVICE BULLETIN (SB) AND THE REQUIREMENTS BULLETIN
(RB) ENSURE THAT THE INFORMATION BETWEEN "RC START" AND "RC END" IN THE SB ARE IDENTICAL
TO THE INFORMATION IN THE SAME SECTIONS (COMPLIANCE, WORK INSTRUCTIONS…) OF THE RB
WHICH THE SB REFERS TO AS THE RELATED DOCUMENT.
1. Effectivity
A. Airplanes
This bulletin is applicable to 767-200, 767-300, 767-300F Airplane(s), line number(s) 2-717,
719-757, 759-768, 770-772, 774-790, 792-798, 800, 802, 806, 808, 811-812, 815, 817, 819,
822-823, 825, 827-829, 831-841, 843-854, 857-858, 860-861, 863, 867, 870, 875, 877, 879-922,
924-964, 966-1064, 1068, 1070-1090, 1093-1097, 1099, 1101, 1103, 1105-1106, 1108, 1110,
1112, 1115, 1118, 1121, 1123, 1125, 1127, 1130, 1133, 1136, 1138, 1140-1142, 1144, 1146,
1148, 1150, 1152-1153, 1155, 1157, 1159, 1161, 1163, 1165, 1167, 1169, 1171, 1173, 1175,
1177, 1179-1180, 1182-1183, 1185-1187, 1189-1191, 1193-1195, 1197-1199, 1201, 1203-1204,
1206, 1208-1209, 1211-1212, 1214-1215, 1217-1218, 1220-1222, 1224-1225, 1227-1229,
1231-1233, 1235, 1237, 1239-1240, 1242, 1244-1245, 1247, 1249, 1251, 1253, 1255-1256, 1258,
1260, 1262-1263, 1265-1266, 1268, 1270, 1272, 1274, 1276, 1278-1279, 1281, 1283, 1285, 1287,
1289, 1291-1292, 1294, 1296, 1298, 1300, 1302, 1304-1305, 1307, 1309, 1311, 1313, 1315,
1317-1318, 1320, 1322-1323, 1325, 1327, 1329-1330, 1332, 1334, 1336, 1338, 1340, 1342-1343,
1345, 1347, 1349, 1351, 1353, 1355-1356, 1358, 1360, 1362-99999 in 1 Group(s). Where the
effectivity is presented with hyphens between line numbers, the airplane applicability means
"through" and "inclusive", e.g. line numbers 1-9 means line numbers 1 through 9 inclusive.
The Variable Numbers and Group Information for the applicable airplanes is given below
NOTE: The Variable Number table below includes affected airplanes available as of the issue
date of this bulletin. Affected airplane Variable Numbers added to MyBoeingFleet.com
after the issue date of this bulletin will be shown using the Maintenance Performance
Toolbox EFFECTIVITY search function result.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: February 06, 2024
767-32A0253 RB
5 of 23

### Page 6

DESCRIPTIONCONFIGURATIONGROUP
All 767-200, 767-300 and 767-300F airplanes.-1
Airplane Models:
767-200, 767-300, 767-300F
GroupVariable Number
1VA002 - VA020
1VA301 - VA315
1VA501 - VA530
1VA701 - VA719
1VA801 - VA810
1VB001 - VB002
1VB051 - VB055
1VB101 - VB125
1VB201 - VB202
1VB251 - VB253
1VB281 - VB284
1VB301 - VB302
1VB321 - VB332
1VB371 - VB373
1VB401
1VB441 - VB444
1VE001 - VE003
1VE021 - VE023
1VE041 - VE043
1VE061 - VE069
1VE083 - VE086
1VE101 - VE104
1VE116 - VE118
1VE121 - VE126
1VE141 - VE152
1VE171 - VE172
GroupVariable Number
1VF001 - VF002
1VF041 - VF042
1VF051
1VF061 - VF062
1VF071 - VF072
1VF091 - VF093
1VF101 - VF102
1VF161 - VF162
1VF171 - VF172
1VF180 - VF184
1VF251
1VK001 - VK016
1VK021 - VK022
1VK031 - VK056
1VK081 - VK113
1VK131 - VK133
1VK141 - VK148
1VK161 - VK164
1VK171
1VK181
1VK186
1VL001 - VL006
1VL011
1VL701 - VL703
1VL751 - VL755
1VL806 - VL807
GroupVariable Number
1VL871 - VL873
1VL891 - VL900
1VL911 - VL914
1VL931 - VL932
1VL941
1VN001 - VN041
1VN051 - VN064
1VN081 - VN099
1VN111 - VN127
1VN130 - VN137
1VN151 - VN158
1VN163 - VN168
1VN171 - VN174
1VN191 - VN198
1VN211 - VN212
1VN221 - VN225
1VN231 - VN234
1VN241 - VN243
1VN251 - VN276
1VN291 - VN293
1VN301 - VN314
1VN371 - VN372
1VN376
1VN381 - VN388
1VN421 - VN427
1VN436
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: February 06, 2024
767-32A0253 RB
6 of 23
REQUIREMENTS BULLETIN 767-32A0253
ALERTALERT

### Page 7

GroupVariable Number
1VN471 - VN472
1VN491 - VN513
1VN531 - VN532
1VN536 - VN537
1VN541 - VN542
1VN546 - VN547
1VN551
1VN556 - VN557
1VN561 - VN562
1VN631 - VN638
1VN651 - VN658
1VN671 - VN672
1VN676
1VN681 - VN691
1VN731 - VN732
1VN751 - VN753
1VN791 - VN792
1VN811 - VN813
1VN921 - VN922
1VN931 - VN936
1VN951 - VN953
1VN966 - VN972
1VR051 - VR060
1VR081
1VR084
1VR086 - VR089
1VR106 - VR109
1VR201 - VR211
1VR251
1VR256 - VR260
1VR266 - VR320
1VR401
1VR421 - VR423
GroupVariable Number
1VR426
1VR441
1VR461
1VR471 - VR472
1VS051 - VS056
1VS061
1VS066 - VS070
1VS073 - VS078
1VS091 - VS104
1VS111 - VS113
1VS131 - VS133
1VS136 - VS137
1VS176 - VS177
1VS186 - VS187
1VS196 - VS203
1VS206 - VS208
1VS211
1VS216 - VS217
1VS231
1VS246 - VS248
1VS261 - VS263
1VS266 - VS274
1VS291 - VS293
1VS301 - VS303
1VS306 - VS311
1VS316
1VS321 - VS324
1VS331 - VS333
1VS336 - VS337
1VS366 - VS367
1VS381 - VS382
1VS391 - VS392
1VS401
GroupVariable Number
1VS426 - VS428
1VS466 - VS472
1VS486
1VS496 - VS497
1VS506 - VS507
1VS526
1VS546 - VS549
1VS701 - VS736
1VS751 - VS759
1VS821 - VS825
1VS841 - VS844
1VS861
1VS881 - VS883
1VS891
1VS896
1VS901 - VS912
1VS916
1VS921 - VS928
1VS931 - VS933
1VS941
1VS951 - VS954
1VS961 - VS969
1VS971 - VS977
1VS981 - VS984
1VT001 - VT013
1VT021
1VT031 - VT033
1VT501
1VT511 - VT513
1VT521 - VT523
1VT531 - VT533
1VT541 - VT546
1VT551 - VT552
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: February 06, 2024
767-32A0253 RB
7 of 23
REQUIREMENTS BULLETIN 767-32A0253
ALERTALERT

### Page 8

GroupVariable Number
1VT556 - VT700
1VT731 - VT735
GroupVariable Number
1VT737
1VW701 - VW721
GroupVariable Number
1VW851
--
B. Spares Affected
Examine your spares supply for the part numbers and serial numbers identified in APPENDIX A,
APPENDIX B and APPENDIX C of this Bulletin. If any affected part numbers and serial numbers
are found, refer to Work Instructions of this Bulletin for the recommended action.
2. CONCURRENT REQUIREMENTS
None.
3. COMPLIANCE
The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to
Requirements Bulletin 767-32A0253 RB. The Airworthiness Directive will make the compliance tasks and
times given in Requirements Bulletin 767-32A0253 RB mandatory.
Accomplish the required action(s), based on the applicable condition(s) in Table 1, in accordance with
Accomplishment Instructions.
When more than one OPTION is given for a CONDITION, do only one of the OPTION numbers. When
more than one ACTION is given for a CONDITION or an OPTION, do all of the ACTION numbers for that
CONDITION or OPTION.
Table 1: Main Landing Gear - Outer Cylinder Part Number and Serial Number Inspection and
Outer Cylinder Replacement
Repeat Inter-
val (Not to Ex-
ceed)
Boeing Recom-
mended
Compliance Time
ActionCondition
-Within 30 months
after the Original
Issue date of Re-
quirements Bul-
letin 767-32A0253
RB
OPTION 1: Do a check
of maintenance records
of the left and right Main
Landing Gear (MLG)
Outer Cylinder part num-
ber and serial number for
any affected part num-
bers and serial numbers
listed in APPENDIX A,
APPENDIX B, and AP-
PENDIX C.
All Airplanes
OPTION 2: Inspect the
left and right MLG Outer
Cylinder part number and
serial number for any af-
fected part numbers and
serial numbers.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: February 06, 2024
767-32A0253 RB
8 of 23
REQUIREMENTS BULLETIN 767-32A0253
ALERTALERT

### Page 9

Table 1: Main Landing Gear - Outer Cylinder Part Number and Serial Number Inspection and
Outer Cylinder Replacement
Repeat Inter-
val (Not to Ex-
ceed)
Boeing Recom-
mended
Compliance Time
ActionCondition
--No further action is re-
quired.
CONDITION 1: NO AF-
FECTED MLG OUTER
CYLINDER FOUND.
-Within 30 months
after the Original
Issue date of Re-
quirements Bul-
letin 767-32A0253
RB
Replace each affected
MLG Outer Cylinder with
a new or serviceable
MLG Outer Cylinder. (a)
CONDITION 2: ANY MLG
OUTER CYLINDER PART
NUMBER AND SERIAL
NUMBER LISTED IN AP-
PENDIX A FOUND.
-Within 46 months
after the Original
Issue date of Re-
quirements Bul-
letin 767-32A0253
RB
Replace each affected
MLG Outer Cylinder with
a new or serviceable
MLG Outer Cylinder. (a)
CONDITION 3: ANY MLG
OUTER CYLINDER PART
NUMBER AND SERIAL
NUMBER LISTED IN AP-
PENDIX B FOUND.
-Within 130 months
after the Original
Issue date of Re-
quirements Bul-
letin 767-32A0253
RB
Replace each affected
MLG Outer Cylinder with
a new or serviceable
MLG Outer Cylinder. (a)
CONDITION 4: ANY MLG
OUTER CYLINDER PART
NUMBER AND SERIAL
NUMBER LISTED IN AP-
PENDIX C FOUND.
(a) A serviceable MLG Outer Cylinder is defined as one that does not have a part number
and serial number identified in APPENDIX A, APPENDIX B and APPENDIX C, or is
a MLG Outer Cylinder that has a part number and serial number identified in AP-
PENDIX A, APPENDIX B or APPENDIX C that has been inspected, applicable on-
condition corrective actions have been done, and part marked in accordance with
APPENDIX D of Requirements Bulletin 767-32A0253 RB.
4. APPROVAL
This Requirements Bulletin was examined by the Federal Aviation Administration (FAA). The changes
specified in this document comply with the applicable regulations and are FAA approved, as well as European
Union Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved
airplanes listed in this Requirements Bulletin effectivity. This document and its approval were based on the
airplane in its original Boeing delivery configuration or as modified by other Boeing changes.
If an airplane has a non-Boeing modification or repair that affects a component or system also affected by
this Requirements Bulletin, the operator is responsible for obtaining appropriate regulatory agency approval
before incorporating this Requirements Bulletin.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: February 06, 2024
767-32A0253 RB
9 of 23
REQUIREMENTS BULLETIN 767-32A0253
ALERTALERT

### Page 10

Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: February 06, 2024
767-32A0253 RB
10 of 23
REQUIREMENTS BULLETIN 767-32A0253
ALERTALERT
BLANK PAGE

### Page 11

5.    ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL INFORMATION
NOTE: 1. This is an Enhanced Required for Compliance document. There will be a separate
Service Bulletin (SB) and a separate Requirements Bulletin (RB). If an RB is mandated
by an Airworthiness Directive (AD), then all applicable requirements specified in the
RB must be done. In the RB, the "Refer to the listed procedures..." column of the
table(s) in the Work Instructions is for reference only. The procedures in that column
are not required by the AD and are for guidance only. For the related SB, some
locations are marked RC Start and RC End to identify the requirements that are
restated from the RB. For the related SB, the areas between RC Start and RC End,
including sub-steps and any figures identified between RC Start and RC End, must
be done to comply with the AD. Therefore, an Alternative Method of Compliance
(AMOC) is required for any deviations to steps between RC Start and RC End,
including substeps and identified figures. For the related SB, the steps not between
RC Start and RC End may be deviated from using accepted methods in accordance
with the operator's maintenance or inspection program without obtaining approval
of an AMOC; this is provided that the steps between RC Start and RC End, including
sub-steps and identified figures, can still be done as specified, and the airplane can
be put back in an airworthy condition. Figures not required for compliance are omitted
from the RB.
2. This is an Enhanced Required for Compliance document. The Boeing processes
used to create the Service Bulletin (SB) and the Requirements Bulletin (RB) ensure
that the information between "RC Start" and "RC End" in the SB are identical to the
information in the same sections (Compliance, Work Instructions...) of the RB which
the SB refers to as the related document.
3. The compliance times for the actions in WORK INSTRUCTIONS are in Compliance.
4. Unless shown differently, these dimensions and tolerances are used:
– Linear dimensions are in inches
– Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus
or minus 0.03 inch
– Tolerance on rivet and bolt edge margin is plus or minus 0.05 inch
– Angular tolerance is plus or minus 2 degrees
– Hole dimensions for standard solid rivets and fasteners are in Structural Repair
Manual (SRM) Chapter 51
– Torque Values:
— Values for structural fasteners are given in 767 Structural Repair Manual,
Chapter 51.
— Values for airframe maintenance tasks are included in Chapter 20 of 767
Aircraft Maintenance Manual (AMM).
— Values for electrical maintenance tasks are included in Chapter 20 of
Standard Wiring Practices Manual (SWPM).
— Values for engine maintenance tasks are included in Chapter 70 of 767
Aircraft Maintenance Manual (AMM).
— Non-standard torque values for maintenance tasks are included in the
applicable installation step.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: February 06, 2024
767-32A0253 RB
11 of 23
REQUIREMENTS BULLETIN 767-32A0253
ALERTALERT

### Page 12

5. These work instructions refer to procedures included in other Boeing documents.
When the words "refer to" are used and the operator has an accepted alternative
procedure, the accepted alternative procedure can be used. When the words "in
accordance with" are included in the instruction, the procedure in the Boeing document
must be used.
6. Where the work instructions include installation of a kept part, a new or serviceable
part with the same part number can be installed as an alternative to the kept part.
7. If it is necessary to remove more parts for access, you can remove those parts. If
you can get access without removing identified parts, it is not necessary to remove
all of the identified parts. Jacking and shoring limitations must be observed.
8. Use the approved fastener, process and material substitutions in accordance with
SRM Chapter 51.
9. When more than one OPTION is given for a CONDITION, do only one of the OPTION
numbers. When more than one ACTION is given for a CONDITION or an OPTION,
do all of the ACTION numbers for that CONDITION or OPTION.
10. The instructions in Work Instructions and the figures can include operation of tools
or test equipment. Boeing Engineering Tool Drawings, the Illustrated Tool and
Equipment Manual, and the Special Tool and Ground Handling Drawing Index contain
data on versions of the tools or test equipment that you can use. It is permitted to
use replaced tools. It is not permitted to use superseded tools.
11. If the length of any fastener specified in this service bulletin does not meet installation
standards given in SRM Chapter 51, then a fastener of the same specification, or
an approved substitute, with a length which meets the installation standards given
in SRM Chapter 51 may be used. In addition, washers may be installed for fastener
grip length in accordance with SRM Chapter 51. Refer to SOPM 20-50-01 for alternate
full threaded fasteners (screws) needed for installation in this service bulletin.
12. Use of colors in Figures is based on guidance from the ATA e-Business Program
(ATA) iSpec 2200.
13. A serviceable MLG Outer Cylinder is defined as one that does not have a part number
and serial number identified in APPENDIX A, APPENDIX B and APPENDIX C, or is
a MLG Outer Cylinder that has a part number and serial number identified in
APPENDIX A, APPENDIX B or APPENDIX C that has been inspected, applicable
on-condition corrective actions have been done, and part marked in accordance with
APPENDIX D of Requirements Bulletin 767-32A0253 RB.
14. A maintenance records check of the left and right MLG Outer Cylinder part number
and serial number for affected part number and serial number can be done provided
the part number and serial number can be conclusively determined from that check.
B. WORK INSTRUCTIONS
Actions Required for Compliance
1. Requirements
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: February 06, 2024
767-32A0253 RB
12 of 23
REQUIREMENTS BULLETIN 767-32A0253
ALERTALERT

### Page 13

Table 1: Main Landing Gear - Outer Cylinder Part Number and Serial Number Inspection and Outer
Cylinder Replacement
Refer to the listed proce-
dures in SB 767-32A0253
Original Issue or later
approved revisions as an
accepted procedure.
Method of ComplianceActionCondition
--OPTION 1: Do a check of
maintenance records of
the left and right Main
Landing Gear (MLG) Outer
Cylinder part number and
serial number for any af-
fected part numbers and
serial numbers listed in
APPENDIX A, APPENDIX
B, and APPENDIX C.
All Airplanes
Do PART 1: PREPARA-
TION
-OPTION 2: Inspect the left
and right MLG Cylinder
part number and serial
number for any affected
part numbers and serial
numbers.
-FIGURE 1
Do PART 4: RESTORA-
TION if PART 1 was done
-No further action is re-
quired.
CONDITION 1: NO AF-
FECTED MLG OUTER
CYLINDER FOUND.
Do PART 1: PREPARA-
TION if not previously
done
-Replace each affected
MLG Outer Cylinder with a
new or serviceable MLG
Outer Cylinder. (a)
CONDITION 2: ANY MLG
OUTER CYLINDER PART
NUMBER AND SERIAL
NUMBER SPECIFIED IN
APPENDIX A FOUND. Do PART 2: MLG RE-MOVAL AND DISASSEM-
BLY
-
Do PART 3: MLG ASSEM-
BLY AND INSTALLATION
-
Do PART 4: RESTORA-
TION
-
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: February 06, 2024
767-32A0253 RB
13 of 23
REQUIREMENTS BULLETIN 767-32A0253
ALERTALERT

### Page 14

Table 1: Main Landing Gear - Outer Cylinder Part Number and Serial Number Inspection and Outer
Cylinder Replacement
Refer to the listed proce-
dures in SB 767-32A0253
Original Issue or later
approved revisions as an
accepted procedure.
Method of ComplianceActionCondition
Do PART 1: PREPARA-
TION if not previously
done
-Replace each affected
MLG Outer Cylinder with a
new or serviceable MLG
Outer Cylinder. (a)
CONDITION 3: ANY MLG
OUTER CYLINDER PART
NUMBER AND SERIAL
NUMBER SPECIFIED IN
APPENDIX B FOUND. Do PART 2: MLG RE-MOVAL AND DISASSEM-
BLY
-
Do PART 3: MLG ASSEM-
BLY AND INSTALLATION
-
Do PART 4: RESTORA-
TION
-
Do PART 1: PREPARA-
TION if not previously
done
-Replace each affected
MLG Outer Cylinder with a
new or serviceable MLG
Outer Cylinder. (a)
CONDITION 4: ANY MLG
OUTER CYLINDER PART
NUMBER AND SERIAL
NUMBER SPECIFIED IN
APPENDIX C FOUND. Do PART 2: MLG RE-MOVAL AND DISASSEM-
BLY
-
Do PART 3: MLG ASSEM-
BLY AND INSTALLATION
-
Do PART 4: RESTORA-
TION
-
(a) A serviceable MLG Outer Cylinder is defined as one that does not have a part number and serial number
identified in APPENDIX A, APPENDIX B and APPENDIX C, or is a MLG Outer Cylinder that has a part
number and serial number identified in APPENDIX A, APPENDIX B or APPENDIX C that has been inspect-
ed, applicable on-condition corrective actions have been done, and part marked in accordance with AP-
PENDIX D of Requirements Bulletin 767-32A0253 RB.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: February 06, 2024
767-32A0253 RB
14 of 23
REQUIREMENTS BULLETIN 767-32A0253
ALERTALERT

### Page 15 (OCR)

REQUIREMENTS BULLETIN 767-32A0253
ALERT  ALERT
FWD
LEFT MAIN LANDING GEAR
INBD
HYDRAULIC LINES REMOVED FOR CLARITY
3048377
FIGURE 1: MAIN LANDING GEAR - OUTER CYLINDER - PART NUMBER AND SERIAL NUMBER
INSPECTION
(SHEET 1 OF 3)
Original Issue: February 06, 2024
Export Controlled ECCN: 9E991  767-32A0253 RB
See page 1 for details  15 of 23

### Page 16 (OCR)

REQUIREMENTS BULLETIN 767-32A0253
ALERT  ALERT
FWD
RIGHT MAIN LANDING GEAR
INBD
FWD
HYDRAULIC LINES REMOVED FOR CLARITY
3048754
FIGURE 1: MAIN LANDING GEAR - OUTER CYLINDER - PART NUMBER AND SERIAL NUMBER
INSPECTION
(SHEET 2 OF 3)
Original Issue: February 06, 2024
767-32A0253 RB
Export Controlled ECCN: 9E991
See page 1 for details  16 of 23

### Page 17

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
More DataQtyIdentificationNameTaskStep
(a)2161T1110-( ) OR
161T1280-( )
OUTER CYLINDER -
MAIN LANDING GEAR
Inspect1
(a) Inspect for affected part number and serial number listed in APPENDIX A, APPENDIX B, and APPENDIX
C.
FIGURE 1: MAIN LANDING GEAR - OUTER CYLINDER - PART NUMBER AND SERIAL NUMBER
INSPECTION
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: February 06, 2024
767-32A0253 RB
17 of 23
REQUIREMENTS BULLETIN 767-32A0253
ALERTALERT

### Page 18

Table A1: Affected MLG Outer Cylinder Serial Numbers - Requiring Chrome Removal
to Packing Bore and Working Inner Diameter
Serial NumberDetail Part Number
5917161T1110-28
6732161T1110-36
7845161T1110-58
Table A2: Affected MLG Outer Cylinder Serial Numbers - Requiring Chrome Removal
to Working Inner Diameter
Serial NumberDetail Part Number
6271161T1110-27
7775161T1110-58
BFG-8868161T1110-84
APPENDIX A: AFFECTED OUTER CYLINDER PART NUMBERS AND SERIAL NUMBERS
(SHEET 1 OF 1)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: February 06, 2024
767-32A0253 RB
18 of 23
REQUIREMENTS BULLETIN 767-32A0253
ALERTALERT

### Page 19

Table B1: Affected MLG Outer Cylinder Serial Numbers - Requiring Chrome Removal
to Packing Bore and Working Inner Diameter
Serial NumberDetail Part Number
5932161T1110-23
6062161T1110-27
6196
6267
6398161T1110-35
6195
5958161T1110-28
5703
5712
6048
6214
6352
6415
6814161T1110-36
7841161T1110-57
CPT-8054
CPT-8077161T1110-58
BFG-8249161T1110-71
CPT-8196161T1110-72
Table B2: Affected MLG Outer Cylinder Serial Numbers - Requiring Chrome Removal
to Working Inner Diameter
Serial NumberDetail Part Number
5677161T1110-27
6272
7781161T1110-35
7207161T1110-36
CPT-8045161T1110-58
APPENDIX B: AFFECTED OUTER CYLINDER PART NUMBERS AND SERIAL NUMBERS
(SHEET 1 OF 1)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: February 06, 2024
767-32A0253 RB
19 of 23
REQUIREMENTS BULLETIN 767-32A0253
ALERTALERT

### Page 20

Table C1: Affected MLG Outer Cylinder Serial Numbers - Requiring Chrome Removal
to Packing Bore Inner Diameter
Serial NumberDetail Part Number
5862161T1110-27
6054
6203
5751161T1110-28
5918
6426161T1110-35
7084
7132
7477
7586
7710
7784
7489161T1110-36
7526
6564
7772
CPT-8053161T1110-57
CPT-8182
CPT-8081
CPT-8143161T1110-58
CPT-7935
BFG-8310161T1110-71
BFG-8609
BFG-8716
BFG-8700161T1110-72
BFG-8318
CPT-8200
BFG-8817161T1110-83
BFG-8829
APPENDIX C: AFFECTED OUTER CYLINDER PART NUMBERS AND SERIAL NUMBERS
(SHEET 1 OF 2)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: February 06, 2024
767-32A0253 RB
20 of 23
REQUIREMENTS BULLETIN 767-32A0253
ALERTALERT

### Page 21

Table C1: Affected MLG Outer Cylinder Serial Numbers - Requiring Chrome Removal
to Packing Bore Inner Diameter
Serial NumberDetail Part Number
BFG-8934161T1110-93
BFG-8957
BFG-8979
BFG-8980
BFG-8981
BFG-9026
BFG-9050
BFG-8929161T1110-94
BFG-8941
BFG-8958
BFG-8972
BFG-8976
BFG-9003
BFG-9020
BFG-9054
BFG-0012161T1280-3
BFG-0024
BFG-0025
BFG-0033
BFG-0007161T1280-4
BFG-0017
BFG-0018
BFG-8590161T1110-84
BFG-8870
APPENDIX C: AFFECTED OUTER CYLINDER PART NUMBERS AND SERIAL NUMBERS
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: February 06, 2024
767-32A0253 RB
21 of 23
REQUIREMENTS BULLETIN 767-32A0253
ALERTALERT

### Page 22 (OCR)

REQUIREMENTS BULLETIN 767-32A0253
ALERT  ALERT
B-B
(zx3
WORKING INNER
DIAMETER
MAIN LANDING GEAR COMPONENT
(TYPICAL)
PACKING BORE
INSPECTION AREA  INNER DIAMETER  3048813
A-A
APPENDIX D: MAIN LANDING GEAR - OUTER CYLINDER - INSPECTION FOR HEAT DAMAGE AND
CRACKS, AND REPAIR
(SHEET 1 OF 2)
Original Issue: February 06, 2024
Export Controlled ECCN: 9E991  767-32A0253 RB
See page 1 for details  22 of 23

### Page 23

The step numbers shown below agree with the numbers shown in the circle symbols in the appendix. The QTY
numbers shown below are the number of parts necessary for this appendix.
More DataQtyIdentificationNameTaskStep
(a)(b)(c)--CHROME PLATINGRemove1
(d)1161T1110-( ) OR
161T1280-( )
OUTER CYLINDER -
MLG
Inspect2
(e)(f)1161T1110-( ) OR
161T1280-( )
OUTER CYLINDER -
MLG
Repair3
(g)--OUTER CYLINDER -
MLG
Identify4
(a) Remove chrome from the MLG Outer Cylinder working inner diameter for those part numbers and serial
numbers found in APPENDIX A Table A2 and APPENDIX B Table B2. Refer to SOPM 20-10-02 as an
accepted procedure.
(b) Remove chrome from the MLG Outer Cylinder packing bore inner diameter and working inner diameter
for those part numbers and serial numbers found in APPENDIX A Table A1 and APPENDIX B Table B1.
Refer to SOPM 20-10-02 as an accepted procedure.
(c) Remove chrome from the MLG Outer Cylinder packing bore for those part numbers and serial numbers
found in APPENDIX C Table C1. Refer to SOPM 20-10-02 as an accepted procedure.
(d) Where chrome was removed, do a Nital Etch inspection for any heat damage and a Magnetic Particle
Inspection for any cracks. Refer to SOPM 20-10-02 and SOPM 20-20-01 as accepted procedures.
(e) If any heat damage or any crack is found, do the repair and apply chrome plate to the MLG Outer Cylinder
inner diameter surfaces in accordance with CMM 32-11-40, REPAIR 1-3.
(f) If no heat damage and no crack is found, apply chrome plate to the MLG Outer Cylinder inner diameter
surfaces. Refer to CMM 32-11-40, REPAIR 1-3.
(g) There is no equivalent Boeing part number for the changed part. Mark on the part that the change in this
bulletin has been done adjacent to and on the same surface as the original manufacturer's permanent
MLG Outer Cylinder part number. Refer to SOPM 20-50-10, Electrochemical Etch Code E, Dot Peen
Code DP or Vibroengraving Code VE, as an accepted procedure. If part mark is illegible after application
of finishes, refer to SOPM 20-50-10, Rubber Stamping Codes RA, RH, and RY, as an accepted procedure.
APPENDIX D: MAIN LANDING GEAR - OUTER CYLINDER - INSPECTION FOR HEAT DAMAGE AND
CRACKS, AND REPAIR
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: February 06, 2024
767-32A0253 RB
23 of 23
REQUIREMENTS BULLETIN 767-32A0253
ALERTALERT

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
