# Boeing Alert Requirements Bulletin 767-53A0301 RB: Revision 2

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2023-1986; AD 2024-05-03 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Alert Requirements Bulletin 767-53A0301 RB](https://openairdocs.org/service-documents/boeing/767-53a0301-rb.md)
- Title as filed: RB-767-53A0301-02
- Pages: 44
- PDF: https://openairdocs.org/files/sha256/55/58/5558c64cd05609659f55e55e73678eadca6a5c58f261a33e0f8ae5d4008da73c
- Page: https://openairdocs.org/service-documents/boeing/767-53a0301-rb/file/5558c64cd056

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Commercial 
Airplanes
767
Requirements Bulletin
ALERT
Number: 767-53A0301 RB
Original Issue: April 21, 2021
Revision 2: May 24, 2023
ATA System: 5300
SUBJECT: FUSELAGE - Section 53 - Forward Entry Door Cutout Aft Lower Corner Fuselage Skin
and Bear Strap Inspection and Repair
EXPORT CONTROLLED - This technology or software is subject to the U.S. Export Administration Regulations
(EAR), (15 C.F.R. Parts 730-774). No authorization from the U.S. Department of Commerce is required for
export, re-export, in-country transfer, or access EXCEPT to country group E:1 or E:2 countries/persons per
Supp.1 to Part 740 of the EAR.
9E991ECCN:
Copyright © 2021 Boeing.
Unpublished Work. All Rights Reserved.
Treatment of this document and its content is governed by contract with Boeing. Rights to use this document
are licensed on a per aircraft basis and such rights may not be transferable. For more information, contact The
Boeing Company.
Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner,
BBJ, DC-8, DC-9, DC-10, KC-10, KC-46, KDC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8, Poseidon and
Boeing liveries are all trademarks owned by The Boeing Company; and no trademark license is granted in
connection with this document unless provided in writing by Boeing.
Original Issue: April 21, 2021
767-53A0301 RBRevision 2: May 24, 2023
1 of 44
2.0

### Page 2

Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 21, 2021
767-53A0301 RBRevision 2: May 24, 2023
2 of 44
REQUIREMENTS BULLETIN 767-53A0301
ALERTALERT
BLANK PAGE

### Page 3

Table of Contents
Revision Transmittal Sheet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1. EFFECTIVITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
A. Airplanes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
B. Spares Affected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2. CONCURRENT REQUIREMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3. COMPLIANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4. APPROVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
5. ACCOMPLISHMENT INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
A. General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
B. Work Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
FIGURE 1: FORWARD ENTRY DOOR CUTOUT AFT LOWER CORNER FUSELAGE SKIN AND BEAR
STRAP - EXTERNAL AND INTERNAL DETAILED INSPECTION . . . . . . . . . . . . . . 27
FIGURE 2: FORWARD SERVICE DOOR CUTOUT AFT LOWER CORNER FUSELAGE SKIN AND BEAR
STRAP - EXTERNAL AND INTERNAL DETAILED INSPECTION  [Group 1] . . . . . . . . 31
FIGURE 3: FORWARD ENTRY DOOR CUTOUT AFT LOWER CORNER FASTENER HOLE LOCATIONS
- OPEN HOLE HIGH FREQUENCY EDDY CURRENT (HFEC) INSPECTION . . . . . . . 35
FIGURE 4: FORWARD SERVICE DOOR CUTOUT AFT LOWER CORNER FASTENER HOLE LOCATIONS
- OPEN HOLE HIGH FREQUENCY EDDY CURRENT (HFEC) INSPECTION  [Group 1] . 38
FIGURE 5: FORWARD ENTRY DOOR CUTOUT AFT LOWER CORNER FUSELAGE SKIN - EXTERNAL
DETAILED INSPECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
FIGURE 6: FORWARD SERVICE DOOR CUTOUT AFT LOWER CORNER FUSELAGE SKIN - EXTERNAL
DETAILED INSPECTION [Group 1] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 21, 2021
767-53A0301 RBRevision 2: May 24, 2023
3 of 44
REQUIREMENTS BULLETIN 767-53A0301
ALERTALERT

### Page 4

Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 21, 2021
767-53A0301 RBRevision 2: May 24, 2023
4 of 44
REQUIREMENTS BULLETIN 767-53A0301
ALERTALERT
BLANK PAGE

### Page 5

Commercial 
Airplanes
767
Requirements Bulletin
ALERT
Revision Transmittal SheetNumber: 767-53A0301 RBOriginal Issue: April 21, 2021
Revision 2: May 24, 2023
ATA System: 5300
SUBJECT: FUSELAGE - Section 53 - Forward Entry Door Cutout Aft Lower Corner Fuselage Skin
and Bear Strap Inspection and Repair
This revision includes all pages of the requirements bulletin.
COMPLIANCE INFORMATION RELATED TO THIS REVISION
The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to Requirements
bulletin 767-53A0301 RB. The Airworthiness Directive will make the compliance tasks and times given in
Requirements bulletin 767-53A0301 RB mandatory.
Effects of this Revision 2 on airplanes on which the Original Issue or Revision 1 was previously done:
None.
REASON FOR REVISION
This revision clarifies compliance action and work instruction action descriptions to be consistent with the area
of inspection.
These sections were changed:
- Compliance: Clarify Action statements.
- Accomplishment Instructions, Work Instructions Table 1 and Table 2: Updated Action description
- Figure 1 and 2: Updated illustration and footnote.
- Figure 3 and 4: Updated footnote.
-Figure 5, Figure 6, Figure 7, Figure 8, Figure 9, and Figure 10: Updated illustration
REVISION HISTORY
Service BulletinService BulletinRequirement BulletinRequirement Bulletin
767-53A0301767-53A0301767-53A0301 RB767-53A0301 RB
Issue DateIssue Date
April 21, 2021Original Issue:April 21, 2021Original Issue:
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 21, 2021
767-53A0301 RBRevision 2: May 24, 2023
5 of 44

### Page 6

April 11, 2022Revision 1:April 11, 2022Revision 1:
May 24, 2023Revision 2:May 24, 2023Revision 2:
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 21, 2021
767-53A0301 RBRevision 2: May 24, 2023
6 of 44
REQUIREMENTS BULLETIN 767-53A0301
ALERTALERT

### Page 7

Commercial 
Airplanes
767
Requirements Bulletin
ALERT
Number: 767-53A0301 RB
Original Issue: April 21, 2021
Revision 2: May 24, 2023
ATA System: 5300
SUBJECT: FUSELAGE - Section 53 - Forward Entry Door Cutout Aft Lower Corner Fuselage Skin
and Bear Strap Inspection and Repair
THIS DOCUMENT IS SENT TO THE OPERATORS OF RECORD OF THE AIRPLANES SHOWN IN
PARAGRAPH 1.A., EFFECTIVITY. IF AN AIRPLANE HAS BEEN LEASED OR SOLD, SEND THIS DOCUMENT
TO THE NEW OPERATOR. IF APPLICABLE SPARES HAVE BEEN SOLD, SEND THIS DOCUMENT TO THE
NEW OWNER. THIS IS AN ENHANCED REQUIRED FOR COMPLIANCE DOCUMENT. THE BOEING
PROCESSES USED TO CREATE THE SERVICE BULLETIN (SB) AND THE REQUIREMENTS BULLETIN
(RB) ENSURE THAT THE INFORMATION BETWEEN "RC START" AND "RC END" IN THE SB ARE IDENTICAL
TO THE INFORMATION IN THE SAME SECTIONS (COMPLIANCE, WORK INSTRUCTIONS…) OF THE RB
WHICH THE SB REFERS TO AS THE RELATED DOCUMENT.
1. Effectivity
A. Airplanes
This bulletin is applicable to 767-200, 767-300, 767-300F, 767-400ER Airplane(s), line number(s)
1-717, 719-1064, 1068, 1070-1090, 1093-1097, 1099, 1101, 1103, 1105-1106, 1108, 1110, 1112,
1115, 1118, 1121, 1123, 1125, 1127, 1130, 1133, 1136, 1138, 1140-1142, 1144, 1146, 1148,
1150, 1152-1153, 1155, 1157, 1159, 1161, 1163, 1165, 1167, 1169, 1171, 1173, 1175, 1177,
1179-1180, 1182-1183, 1185-1187, 1189-1191, 1193-1195, 1197-1199, 1201, 1203-1204, 1206,
1208-1209, 1211-1212, 1214-1215, 1217-1218, 1220-1222, 1224-1225, 1227-1229, 1231-1233,
1235, 1237, 1239-1240, 1242, 1244-1245, 1247, 1249, 1251, 1253, 1255-1256, 1258, 1260,
1262-1263, 1265-1266, 1268, 1270, 1272 in 2 Group(s). Where the effectivity is presented with
hyphens between line numbers, the airplane applicability means "through" and "inclusive", e.g.
line numbers 1-9 means line numbers 1 through 9 inclusive.
The Variable Numbers and Group Information for the applicable airplanes is given below.
DESCRIPTIONCONFIGURATIONGROUP
767-200/-300/-400ER Airplanes with forward entry door and forward
service door.
-1
767-300F Airplanes with forward entry door and no forward service
door.
-2
Airplane Models:
767-200, 767-300, 767-300F, 767-400ER
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 21, 2021
767-53A0301 RBRevision 2: May 24, 2023
7 of 44

### Page 8

GroupVariable Number
1VA001 - VA020
1VA301 - VA315
1VA501 - VA530
1VA701 - VA719
1VA801 - VA810
1VB001 - VB002
1VB051 - VB055
1VB101 - VB125
1VB201 - VB202
1VB251 - VB253
1VB281 - VB284
1VB301 - VB302
1VB321 - VB332
1VB371 - VB373
1VB401
1VB441 - VB444
1VE001 - VE003
1VE021 - VE023
1VE041 - VE043
1VE061 - VE069
1VE083 - VE086
1VE101 - VE104
1VE116 - VE118
1VE121 - VE126
1VE141 - VE152
1VE171 - VE172
1VF001 - VF002
1VF041 - VF042
1VF051
1VF061 - VF062
1VF071 - VF072
1VF091 - VF093
1VF101 - VF102
GroupVariable Number
1VF161 - VF162
1VF171 - VF172
1VF180 - VF184
1VF251
1VK001 - VK016
1VK021 - VK022
1VK031 - VK056
1VK081 - VK113
1VK131 - VK133
1VK141 - VK148
1VK161 - VK164
1VK171
1VK181
1VK186
1VL001 - VL006
1VL011
1VL701 - VL703
1VL751 - VL755
1VL806 - VL807
1VL871 - VL873
1VL891 - VL900
1VL911 - VL914
1VL931 - VL932
1VL941
1VN001 - VN041
1VN051 - VN064
1VN081 - VN099
1VN111 - VN127
1VN130 - VN137
1VN151 - VN158
1VN163 - VN168
1VN171 - VN174
1VN191 - VN198
GroupVariable Number
1VN211 - VN212
1VN221 - VN225
1VN231 - VN234
1VN241 - VN243
1VN251 - VN276
1VN291 - VN293
1VN301 - VN314
1VN371 - VN372
1VN376
1VN381 - VN388
1VN421 - VN427
1VN436
1VN471 - VN472
1VN491 - VN513
1VN531 - VN532
1VN536 - VN537
1VN541 - VN542
1VN546 - VN547
1VN551
1VN556 - VN557
1VN561 - VN562
1VN631 - VN638
1VN651 - VN658
1VN671 - VN672
1VN676
1VN681 - VN691
1VN731 - VN732
1VN751 - VN753
1VN791 - VN792
1VN811 - VN813
1VN921 - VN922
1VN931 - VN936
1VN951 - VN953
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 21, 2021
767-53A0301 RBRevision 2: May 24, 2023
8 of 44
REQUIREMENTS BULLETIN 767-53A0301
ALERTALERT

### Page 9

GroupVariable Number
1VN966 - VN972
1VQ001 - VQ021
1VQ071 - VQ086
1VQ111
1VR051 - VR060
1VR081
1VR084
1VR086 - VR089
1VR106 - VR109
2VR201 - VR211
2VR251
2VR256 - VR260
2VR266 - VR305
1VR401
1VR421 - VR423
1VR426
1VR441
1VR461
1VR471 - VR472
1VS051 - VS056
1VS061
1VS066 - VS070
1VS073 - VS078
1VS091 - VS104
1VS111 - VS113
1VS131 - VS133
1VS136 - VS137
1VS176 - VS177
1VS186 - VS187
GroupVariable Number
1VS196 - VS203
1VS206 - VS208
1VS211
1VS216 - VS217
1VS231
1VS246 - VS248
1VS261 - VS263
1VS266 - VS274
1VS291 - VS293
1VS301 - VS303
1VS306 - VS311
1VS316
1VS321 - VS324
1VS331 - VS333
1VS336 - VS337
1VS366 - VS367
1VS381 - VS382
1VS391 - VS392
1VS401
1VS426 - VS428
1VS466 - VS472
1VS486
1VS496 - VS497
1VS506 - VS507
1VS526
1VS546 - VS549
1VS701 - VS736
1VS751 - VS759
1VS821 - VS825
GroupVariable Number
1VS841 - VS844
1VS861
1VS881 - VS883
1VS891
1VS896
1VS901 - VS912
1VS916
1VS921 - VS928
1VS931 - VS933
1VS941
1VS951 - VS954
1VS961 - VS969
1VS971 - VS977
1VS981 - VS984
1VT001 - VT013
1VT021
1VT031 - VT033
2VT501
2VT511 - VT513
2VT521 - VT523
2VT531 - VT533
2VT541 - VT546
2VT551 - VT552
2VT556 - VT667
2VT731 - VT735
1VV001
2VW701 - VW721
2VW851
--
B. Spares Affected
None.
2. CONCURRENT REQUIREMENTS
None.
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 21, 2021
767-53A0301 RBRevision 2: May 24, 2023
9 of 44
REQUIREMENTS BULLETIN 767-53A0301
ALERTALERT

### Page 10

3. COMPLIANCE
The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to
Requirements Bulletin 767-53A0301 RB. The Airworthiness Directive will make the compliance tasks and
times given in the Requirements Bulletin 767-53A0301 RB mandatory.
Group 1:
Accomplish the required action(s), based on the applicable conditions in Table(s) 1 and 2, in accordance
with Accomplishment Instructions.
Group 2:
Accomplish the required action(s), based on the applicable condition(s) in Table 1 in accordance with
Accomplishment Instructions.
When more than one OPTION is given for a CONDITION, do only one of the OPTION numbers. When
more than one ACTION is given for a CONDITION or an OPTION, do all of the ACTION numbers for
CONDITION or OPTION.
Table 1: Inspection of the Forward Entry Door Cutout Aft Lower Corner Fuselage Skin and Bear Strap
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Within 3,000
Flight Cycles or
24 months after
the Original Is-
sue date of Re-
quirements Bul-
letin 767-
53A0301 RB
whichever oc-
curs first.
Before 20,000
Total Flight Cy-
cles.
OPTION 1 ACTION 1:
Do an External and Internal
Detailed Inspection at the
Forward Entry Door Cutout
Aft lower corner Fuselage
Skin and Bear Strap area
for any crack.(a)
All Airplanes
OPTION 1 ACTION 2:
Do an Open Hole High Fre-
quency Eddy Current
(HFEC) Inspection at the
Forward Entry Door Cutout
Aft lower corner fastener
hole locations for any
crack.(a)
OPTION 2
Do an External Detailed In-
spection at the Forward En-
try Door Cutout Aft lower
corner Fuselage Skin area
for any crack.(a)
-Before further flight.Do the repair in accordance
to SRM 53-10-01 Repair 1.
CONDITION 1:
ANY CRACK FOUND
AND IS WITHIN REPAIR
LIMITS.
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 21, 2021
767-53A0301 RBRevision 2: May 24, 2023
10 of 44
REQUIREMENTS BULLETIN 767-53A0301
ALERTALERT

### Page 11

Table 1: Inspection of the Forward Entry Door Cutout Aft Lower Corner Fuselage Skin and Bear Strap
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flight.Contact The Boeing Compa-
ny for repair instructions
and do the repair.
CONDITION 2:
ANY CRACK FOUND
THAT EXCEEDS THE
REPAIR LIMITS.
6,000 Flight Cy-
cles.
-OPTION 1 ACTION 1:
Repeat the External and In-
ternal Detailed Inspection
at the Forward Entry Door
Cutout Aft lower corner
Fuselage Skin and Bear
Strap area for any crack.(b)
CONDITION 3:
NO CRACK FOUND AS
A RESULT OF OPTION
1 INSPECTION.
(c)
-OPTION 1 ACTION 2:
Repeat the Open Hole
HFEC Inspection at the
Forward Entry Door Cutout
Aft lower corner fastener
hole locations for any
crack.(b)
(d)Within 6,000 Flight Cycles after
the most recent OPTION 1 inspec-
tion was done.
OPTION 2
Repeat the External De-
tailed Inspection at the For-
ward Entry Door Cutout Aft
lower corner Fuselage Skin
area for any crack.(b)
(d)Within 1,500 Flight Cycles after
the most recent OPTION 2 inspec-
tion was done.
OPTION 1 ACTION 1:
Repeat the External and In-
ternal Detailed Inspection
at the Forward Entry Door
Cutout Aft lower corner
Fuselage Skin and Bear
Strap area for any crack.(b)
CONDITION 4:
NO CRACK FOUND AS
A RESULT OF OPTION
2 INSPECTION.
Within 1,500 Flight Cycles after
the most recent OPTION 2 inspec-
tion was done.
OPTION 1 ACTION 2:
Repeat the Open Hole
HFEC Inspection at the
Forward Entry Door Cutout
Aft lower corner fastener
hole locations for any
crack.(b)
1,500 Flight Cy-
cles. (c)
-OPTION 2
Repeat the External De-
tailed Inspection at the For-
ward Entry Door Cutout Aft
lower corner Fuselage Skin
area for any crack.(b)
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 21, 2021
767-53A0301 RBRevision 2: May 24, 2023
11 of 44
REQUIREMENTS BULLETIN 767-53A0301
ALERTALERT

### Page 12

Table 1: Inspection of the Forward Entry Door Cutout Aft Lower Corner Fuselage Skin and Bear Strap
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
(a) It is not required to do the inspections in accordance with Requirements Bulletin 767-53A0301 RB in areas
where a repair covers the affected inspection area and meets any of the following conditions:
1. Repair is accomplished in accordance with 767-200 SRM 53-10-01 Repair 1, 767-300 SRM 53-
10-01 Repair 1, 767-300F SRM 53-10-01 Repair 1 or 767-400 SRM 53-10-01 Repair 1.
2. The repair was approved by the Boeing Organization Designation Authorization (ODA) via an
FAA Form 8100-9 which contains a repeat inspection program for the subject area.
(b) It is not required to do the inspections in accordance with Requirements Bulletin 767-53A0301 RB in areas
where a repair covers the affected inspection area and meets any of the following conditions:
1. The repair is the corrective action to the crack condition identified in Requirements Bulletin 767-
53A0301 RB installed after the Original Issue date of Requirements Bulletin 767-53A0301 RB
2. The repair was approved by the Boeing Organization Designation Authorization (ODA) via an
FAA Form 8100-9 which contains a repeat inspection program for the subject area.
(c) After the accomplishment of this OPTION, it is acceptable to change the repeat action from this OPTION
to any other OPTION under this CONDITION. Operators must comply with the compliance time given for
the chosen OPTION under this CONDITION.
(d) Refer to the applicable CONDITION for further ACTIONS.
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 21, 2021
767-53A0301 RBRevision 2: May 24, 2023
12 of 44
REQUIREMENTS BULLETIN 767-53A0301
ALERTALERT

### Page 13

Group 1:
Table 2: Inspection of the Forward Service Door Cutout Aft Lower Corner Fuselage Skin and Bear Strap
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Within 3,000
Flight Cycles or
24 months after
the Original Is-
sue date of Re-
quirements Bul-
letin 767-
53A0301 RB
whichever oc-
curs first.
Before 20,000
Total Flight Cy-
cles.
OPTION 1 ACTION 1:
Do an External and Internal
Detailed Inspection at the
Forward Service Door
Cutout Aft lower corner
Fuselage Skin and Bear
Strap area for any crack.(a)
All Airplanes
OPTION 1 ACTION 2:
Do an Open Hole High Fre-
quency Eddy Current
(HFEC) Inspection at the
Forward Service Door
Cutout Aft lower corner fas-
tener hole locations for any
crack.(a)
OPTION 2:
Do an External Detailed In-
spection at the Forward
Service Door Cutout Aft
lower corner Fuselage Skin
area for any crack.(a)
-Before further flight.Do the repair in accordance
to SRM 53-10-01 Repair 1.
CONDITION 5:
ANY CRACK FOUND
AND IS WITHIN REPAIR
LIMITS.
-Before further flight.Contact The Boeing Compa-
ny for repair instructions
and do the repair.
CONDITION 6:
ANY CRACK FOUND
THAT EXCEEDS THE
REPAIR LIMITS.
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 21, 2021
767-53A0301 RBRevision 2: May 24, 2023
13 of 44
REQUIREMENTS BULLETIN 767-53A0301
ALERTALERT

### Page 14

Group 1:
Table 2: Inspection of the Forward Service Door Cutout Aft Lower Corner Fuselage Skin and Bear Strap
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
6,000 Flight Cy-
cles.
-OPTION 1 ACTION 1
Repeat the External and In-
ternal Detailed Inspection
at the Forward Service Door
Cutout Aft lower corner
Fuselage Skin and Bear
Strap area for any crack.(b)
CONDITION 7:
NO CRACK FOUND AS
A RESULT OF OPTION
1 INSPECTION.
(c)
-OPTION 1 ACTION 2:
Repeat the Open Hole
HFEC Inspection at the
Forward Service Door
Cutout Aft lower corner fas-
tener hole locations for any
crack.(b)
(d)Within 6,000 Flight Cycles after
the most recent OPTION 1 inspec-
tion was done.
OPTION 2:
Repeat the External De-
tailed Inspection at the For-
ward Service Door Cutout
Aft lower corner Fuselage
Skin area for any crack.(b)
(d)Within 1,500 Flight Cycles after
the most recent OPTION 2 inspec-
tion was done.
OPTION 1 ACTION 1
Repeat the External and In-
ternal Detailed Inspection
at the Forward Service Door
Cutout Aft lower corner
Fuselage Skin and Bear
Strap area for any crack.(b)
CONDITION 8:
NO CRACK FOUND AS
A RESULT OF OPTION
2 INSPECTION.
Within 1,500 Flight Cycles after
the most recent OPTION 2 inspec-
tion was done.
OPTION 1 ACTION 2:
Repeat the Open Hole
HFEC Inspection at the
Forward Service Door
Cutout Aft lower corner fas-
tener hole locations for any
crack.(b)
1,500 Flight Cy-
cles. (c)
-OPTION 2
Repeat the External De-
tailed Inspection at the For-
ward Service Door Cutout
Aft lower corner Fuselage
Skin area for any crack.(b)
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 21, 2021
767-53A0301 RBRevision 2: May 24, 2023
14 of 44
REQUIREMENTS BULLETIN 767-53A0301
ALERTALERT

### Page 15

Group 1:
Table 2: Inspection of the Forward Service Door Cutout Aft Lower Corner Fuselage Skin and Bear Strap
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
(a) It is not required to do the inspections in accordance with Requirements Bulletin 767-53A0301 RB in areas
where a repair covers the affected inspection area and meets any of the following conditions:
1. Repair is accomplished in accordance with 767-200 SRM 53-10-01 Repair 1, 767-300 SRM 53-
10-01 Repair 1 or 767-400 SRM 53-10-01 Repair.
2. The repair was approved by the Boeing Organization Designation Authorization (ODA) via an
FAA Form 8100-9 which contains a repeat inspection program for the subject area.
(b) It is not required to do the inspections in accordance with Requirements Bulletin 767-53A0301 RB in areas
where a repair covers the affected inspection area and meets any of the following conditions:
1. The repair is the corrective action to the crack condition identified in Requirements Bulletin 767-
53A0301 RB installed after the Original Issue date of Requirements Bulletin 767-53A0301 RB
2. The repair was approved by the Boeing Organization Designation Authorization (ODA) via an
FAA Form 8100-9 which contains a repeat inspection program for the subject area.
(c) After the accomplishment of this OPTION, it is acceptable to change the repeat action from this OPTION
to any other OPTION under this CONDITION. Operators must comply with the compliance time given for
the chosen OPTION under this CONDITION.
(d) Refer to the applicable CONDITION for further ACTIONS.
4. APPROVAL
This Requirements Bulletin was examined by the Federal Aviation Administration (FAA). The changes
specified in this document comply with the applicable regulations and are FAA approved, as well as European
Union Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved
airplanes listed in this Requirements Bulletin effectivity. This document and its approval were based on the
airplane in its original Boeing delivery configuration or as modified by other Boeing changes.
If an airplane has a non-Boeing modification or repair that affects a component or system also affected by
this Requirements Bulletin, the operator is responsible for obtaining appropriate regulatory agency approval
before incorporating this Requirements Bulletin.
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 21, 2021
767-53A0301 RBRevision 2: May 24, 2023
15 of 44
REQUIREMENTS BULLETIN 767-53A0301
ALERTALERT

### Page 16

Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 21, 2021
767-53A0301 RBRevision 2: May 24, 2023
16 of 44
REQUIREMENTS BULLETIN 767-53A0301
ALERTALERT
BLANK PAGE

### Page 17

5.    ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL INFORMATION
NOTE: 1. This is an Enhanced Required for Compliance document. There will be a separate
Service Bulletin (SB) and a separate Requirements Bulletin (RB). If an RB is mandated
by an Airworthiness Directive (AD), then all applicable requirements specified in the
RB must be done. For the related SB, some locations are marked RC Start and RC
End to identify the requirements that are restated from the RB. For the related SB,
the areas between RC Start and RC End, including sub-steps and any figures
identified between RC Start and RC End, must be done to comply with the AD.
Therefore, an Alternative Method of Compliance (AMOC) is required for any deviations
to steps between RC Start and RC End, including substeps and identified figures.
For the related SB, the steps not between RC Start and RC End may be deviated
from using accepted methods in accordance with the operator's maintenance or
inspection program without obtaining approval of an AMOC; this is provided that the
steps between RC Start and RC End, including sub-steps and identified figures, can
still be done as specified, and the airplane can be put back in an airworthy condition.
Figures not required for compliance are omitted from the RB.
2. This is an Enhanced Required for Compliance document. The Boeing processes
used to create the Service Bulletin (SB) and the Requirements Bulletin (RB) ensure
that the information between "RC Start" and "RC End" in the SB are identical to the
information in the same sections (Compliance, Work Instructions...) of the RB which
the SB refers to as the related document.
3. The compliance times for the actions in WORK INSTRUCTIONS are in Compliance.
4. Boeing Service Letter 767-SL-51-036, Damage Reporting and Repair Plan/Design
Guidelines, is an acceptable procedure to request information from Boeing for
additional structural repair instructions. The Service Letter describes what information
must be provided to Boeing before a structural repair can be provided.
5. Unless shown differently, these dimensions and tolerances are used:
– Linear dimensions are in inches
– Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus
or minus 0.03 inch
– Tolerance on rivet and bolt edge margin is plus or minus 0.05 inch
– Angular tolerance is plus or minus 2 degrees
– Hole dimensions for standard solid rivets and fasteners are in Structural Repair
Manual (SRM) Chapter 51
– Torque Values:
— Values for structural fasteners are given in 767 Structural Repair Manual,
Chapter 51.
— Values for airframe maintenance tasks are included in Chapter 20 of 767
Aircraft Maintenance Manual (AMM).
— Values for electrical maintenance tasks are included in Chapter 20 of
Standard Wiring Practices Manual (SWPM).
— Values for engine maintenance tasks are included in Chapter 70 of 767
Aircraft Maintenance Manual (AMM).
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 21, 2021
767-53A0301 RBRevision 2: May 24, 2023
17 of 44
REQUIREMENTS BULLETIN 767-53A0301
ALERTALERT

### Page 18

— Non-standard torque values for maintenance tasks are included in the
applicable installation step.
6. These work instructions refer to procedures included in other Boeing documents.
When the words "refer to" are used and the operator has an accepted alternative
procedure, the accepted alternative procedure can be used. When the words "in
accordance with" are included in the instruction, the procedure in the Boeing document
must be used.
7. Where the work instructions include installation of a kept part, a new or serviceable
part with the same part number can be installed as an alternative to the kept part.
8. If it is necessary to remove more parts for access, you can remove those parts. If
you can get access without removing identified parts, it is not necessary to remove
all of the identified parts. Jacking and shoring limitations must be observed.
9. Use the approved fastener, process and material substitutions in accordance with
SRM Chapter 51.
10. A Detailed Inspection is defined as: An intensive examination of a specific item,
installation or assembly to detect damage, failure or irregularity. This could include
tactile assessment in which a component or assembly can be checked for
tightness/security. Available lighting is normally supplemented with a direct source
of good lighting at an intensity deemed appropriate. Inspection aids such as mirrors
and magnifying lenses may be necessary. Surface cleaning and elaborate access
procedures may be required.
11. When more than one OPTION is given for a CONDITION, do only one of the OPTION
numbers. When more than one ACTION is given for a CONDITION or an OPTION,
do all of the ACTION numbers for that CONDITION or OPTION.
12. If the length of any fastener specified in this service bulletin does not meet installation
standards given in SRM Chapter 51, then a fastener of the same specification, or
an approved substitute, with a length which meets the installation standards given
in SRM Chapter 51 may be used. In addition, washers may be installed for fastener
grip length in accordance with SRM Chapter 51. Refer to SOPM 20-50-01 for alternate
full threaded fasteners (screws) needed for installation in this service bulletin.
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 21, 2021
767-53A0301 RBRevision 2: May 24, 2023
18 of 44
REQUIREMENTS BULLETIN 767-53A0301
ALERTALERT

### Page 19

B. WORK INSTRUCTIONS
Actions Required For Compliance
1. Requirements
Table 1: Inspection of the Forward Entry Door Cutout Aft Lower Corner Fuselage Skin and Bear Strap
Refer to the listed
procedures in SB
767-53A0301
original issue or
later approved re-
visions as an ac-
cepted proce-
dure.
Method of ComplianceActionCondition
Do PART 1:-OPTION 1 ACTION 1:All Airplanes
OPEN ACCESS.Do an External and Internal
Detailed Inspection at the
Forward Entry Door Cutout
Aft lower corner Fuselage
Skin and Bear Strap area
for any crack.(a)
Do PART 2:
REMOVE SEAL
PLATE.
-
-FIGURE 1
-FIGURE 3OPTION 1 ACTION 2:
Do an Open Hole High Fre-
quency Eddy Current
(HFEC) Inspection at the
Forward Entry Door Cutout
Aft lower corner fastener
hole locations for any
crack.(a)
-FIGURE 5OPTION 2:
Do an External Detailed In-
spection at the Forward En-
try Door Cutout Aft lower
corner Fuselage Skin area
for any crack.(a)
-In accordance with 767-200 SRM
53-10-01 Repair 1, 767-300 SRM
53-10-01 Repair 1, 767-300F SRM
53-10-01 Repair 1 or 767-400
SRM 53-10-01 Repair 1 as appli-
cable.
Do the repair in accordance
to SRM 53-10-01 Repair 1.
(c)
CONDITION 1:
ANY CRACK FOUND
AND IS WITHIN REPAIR
LIMITS.
Do PART 3:-
INSTALL SEAL
PLATE.
Do PART 4:-
CLOSE ACCESS.
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 21, 2021
767-53A0301 RBRevision 2: May 24, 2023
19 of 44
REQUIREMENTS BULLETIN 767-53A0301
ALERTALERT

### Page 20

Table 1: Inspection of the Forward Entry Door Cutout Aft Lower Corner Fuselage Skin and Bear Strap
Refer to the listed
procedures in SB
767-53A0301
original issue or
later approved re-
visions as an ac-
cepted proce-
dure.
Method of ComplianceActionCondition
Do PART 3:-Contact The Boeing Compa-
ny for repair instructions
and do the repair.
CONDITION 2:
ANY CRACK FOUND
THAT EXCEEDS THE
REPAIR LIMITS.
INSTALL SEAL
PLATE.
Do PART 4:-
CLOSE ACCESS.
Do PART 3:--CONDITION 3:
INSTALL SEAL
PLATE.
NO CRACK FOUND AS
A RESULT OF OPTION
1 INSPECTION. Do PART 4:-
CLOSE ACCESS.
Do PART 1:-OPTION 1 ACTION 1:
OPEN ACCESS.Repeat the External and In-
ternal Detailed Inspection
at the Forward Entry Door
Cutout Aft lower corner
Fuselage Skin and Bear
Strap area for any crack.(b)
Do PART 2:
REMOVE SEAL
PLATE.
-
-FIGURE 1
-FIGURE 3OPTION 1 ACTION 2:
Repeat the Open Hole
HFEC Inspection at the
Forward Entry Door Cutout
Aft lower corner fastener
hole locations for any
crack.(b)
-FIGURE 5OPTION 2:
Repeat the External De-
tailed Inspection at the For-
ward Entry Door Cutout Aft
lower corner Fuselage Skin
area for any crack.(b)
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 21, 2021
767-53A0301 RBRevision 2: May 24, 2023
20 of 44
REQUIREMENTS BULLETIN 767-53A0301
ALERTALERT

### Page 21

Table 1: Inspection of the Forward Entry Door Cutout Aft Lower Corner Fuselage Skin and Bear Strap
Refer to the listed
procedures in SB
767-53A0301
original issue or
later approved re-
visions as an ac-
cepted proce-
dure.
Method of ComplianceActionCondition
Do PART 3:--CONDITION 4:
INSTALL SEAL
PLATE.
NO CRACK FOUND AS
A RESULT OF OPTION
2 INSPECTION. Do PART 4:-
CLOSE ACCESS.
Do PART 1:-OPTION 1 ACTION 1:
OPEN ACCESS.Repeat the External and In-
ternal Detailed Inspection
at the Forward Entry Door
Cutout Aft lower corner
Fuselage Skin and Bear
Strap area for any crack.(b)
Do PART 2:
REMOVE SEAL
PLATE.
-
-FIGURE 1
-FIGURE 3OPTION 1 ACTION 2:
Repeat the Open Hole
HFEC Inspection at the
Forward Entry Door Cutout
Aft lower corner fastener
hole locations for any
crack.(b)
-FIGURE 5OPTION 2:
Repeat the External De-
tailed Inspection at the For-
ward Entry Door Cutout Aft
lower corner Fuselage Skin
area for any crack.(b)
(a) It is not required to do the inspections in accordance with Requirements Bulletin RB in areas where a
repair covers the affected inspection area and meets any of the following conditions:
1. Repair is accomplished in accordance with 767-200 SRM 53-10-01 Repair 1, 767-300 SRM 53-
10-01 Repair 1, 767-300F SRM 53-10-01 Repair 1 or 767-400 SRM 53-10-01 Repair 1.
2. The repair was approved by the Boeing Organization Designation Authorization (ODA) via an
FAA Form 8100-9 which contains a repeat inspection program for the subject area.
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 21, 2021
767-53A0301 RBRevision 2: May 24, 2023
21 of 44
REQUIREMENTS BULLETIN 767-53A0301
ALERTALERT

### Page 22

Table 1: Inspection of the Forward Entry Door Cutout Aft Lower Corner Fuselage Skin and Bear Strap
Refer to the listed
procedures in SB
767-53A0301
original issue or
later approved re-
visions as an ac-
cepted proce-
dure.
Method of ComplianceActionCondition
(b) It is not required to do the inspections in accordance with Requirements Bulletin RB in areas where a
repair covers the affected inspection area and meets any of the following conditions:
1. The repair is the corrective action to the crack condition identified in Requirements Bulletin 767-
53A0301 RB and installed after the Original Issue date of Requirements Bulletin 767-53A0301
RB.
2. The repair was approved by the Boeing Organization Designation Authorization (ODA) via an
FAA Form 8100-9 which contains a repeat inspection program for the subject area.
(c) Accomplishment of the SRM Repair 1 is terminating action for the inspections at this location only.
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 21, 2021
767-53A0301 RBRevision 2: May 24, 2023
22 of 44
REQUIREMENTS BULLETIN 767-53A0301
ALERTALERT

### Page 23

Group 1:
Table 2: Inspection of the Forward Service Door Cutout Aft Lower Corner Fuselage Skin and Bear Strap
Refer to the listed
procedures in SB
767-53A0301
original issue or
later approved re-
visions as an ac-
cepted proce-
dure.
Method of ComplianceActionCondition
Do PART 1:-OPTION 1 ACTION 1:All Airplanes
OPEN ACCESS.Do an External and Internal
Detailed Inspection at the
Forward Service Door
Cutout Aft lower corner
Fuselage Skin and Bear
Strap area for any crack.(a)
Do PART 2:
REMOVE SEAL
PLATE.
-
-FIGURE 2
-FIGURE 4OPTION 1 ACTION 2:
Do an Open Hole High Fre-
quency Eddy Current
(HFEC) Inspection at the
Forward Service Door
Cutout Aft lower corner fas-
tener hole locations for any
crack.(a)
-FIGURE 6OPTION 2:
Do an External Detailed In-
spection at the Forward
Service Door Cutout Aft
lower corner Fuselage Skin
area for any crack.(a)
-In accordance with 767-200 SRM
53-10-01 Repair 1, 767-300 SRM
53-10-01 Repair 1 or 767-400
SRM 53-10-01 Repair 1 as appli-
cable.
Do the repair in accordance
to SRM 53-10-01 Repair 1.
(c)
CONDITION 5:
ANY CRACK FOUND
AND IS WITHIN REPAIR
LIMITS.
Do PART 3:-
INSTALL SEAL
PLATE.
Do PART 4:-
CLOSE ACCESS.
Do PART 3:-Contact The Boeing Compa-
ny for repair instructions
and do the repair.
CONDITION 6:
ANY CRACK FOUND
THAT EXCEEDS THE
REPAIR LIMITS.
INSTALL SEAL
PLATE.
Do PART 4:-
CLOSE ACCESS.
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 21, 2021
767-53A0301 RBRevision 2: May 24, 2023
23 of 44
REQUIREMENTS BULLETIN 767-53A0301
ALERTALERT

### Page 24

Group 1:
Table 2: Inspection of the Forward Service Door Cutout Aft Lower Corner Fuselage Skin and Bear Strap
Refer to the listed
procedures in SB
767-53A0301
original issue or
later approved re-
visions as an ac-
cepted proce-
dure.
Method of ComplianceActionCondition
Do PART 3:--CONDITION 7:
INSTALL SEAL
PLATE.
NO CRACK FOUND AS
A RESULT OF OPTION
1 INSPECTION. Do PART 4:-
CLOSE ACCESS.
Do PART 1:-OPTION 1 ACTION 1:
OPEN ACCESS.Repeat the External and In-
ternal Detailed Inspection
at the Forward Service Door
Cutout Aft lower corner
Fuselage Skin and Bear
Strap area for any crack.(b)
Do PART 2:
REMOVE SEAL
PLATE.
-
-FIGURE 2
-FIGURE 4OPTION 1 ACTION 2:
Repeat the Open Hole
HFEC Inspection at the
Forward Service Door
Cutout Aft lower corner fas-
tener hole locations for any
crack.(b)
-FIGURE 6OPTION 2:
Repeat the External De-
tailed Inspection at the For-
ward Service Door Cutout
Aft lower corner Fuselage
Skin area for any crack.(b)
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 21, 2021
767-53A0301 RBRevision 2: May 24, 2023
24 of 44
REQUIREMENTS BULLETIN 767-53A0301
ALERTALERT

### Page 25

Group 1:
Table 2: Inspection of the Forward Service Door Cutout Aft Lower Corner Fuselage Skin and Bear Strap
Refer to the listed
procedures in SB
767-53A0301
original issue or
later approved re-
visions as an ac-
cepted proce-
dure.
Method of ComplianceActionCondition
Do PART 3:--CONDITION 8:
INSTALL SEAL
PLATE.
NO CRACK FOUND AS
A RESULT OF OPTION
2 INSPECTION. Do PART 4:-
CLOSE ACCESS.
Do PART 1:-OPTION 1 ACTION 1:
OPEN ACCESS.Repeat the External and In-
ternal Detailed Inspection
at the Forward Service Door
Cutout Aft lower corner
Fuselage Skin and Bear
Strap area for any crack.(b)
Do PART 2:
REMOVE SEAL
PLATE.
-
-FIGURE 2
-FIGURE 4OPTION 1 ACTION 2:
Repeat the Open Hole
HFEC Inspection at the
Forward Service Door
Cutout Aft lower corner fas-
tener hole locations for any
crack.(b)
-FIGURE 6OPTION 2:
Repeat the External De-
tailed Inspection at the For-
ward Service Door Cutout
Aft lower corner Fuselage
Skin area for any crack.(b)
(a) It is not required to do the inspections in accordance with Requirements Bulletin RB in areas where a
repair covers the affected inspection area and meets any of the following conditions:
1. Repair is accomplished in accordance with 767-200 SRM 53-10-01 Repair 1, 767-300 SRM 53-
10-01 Repair 1 or 767-400 SRM 53-10-01 Repair 1.
2. The repair was approved by the Boeing Organization Designation Authorization (ODA) via an
FAA Form 8100-9 which contains a repeat inspection program for the subject area.
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 21, 2021
767-53A0301 RBRevision 2: May 24, 2023
25 of 44
REQUIREMENTS BULLETIN 767-53A0301
ALERTALERT

### Page 26

Group 1:
Table 2: Inspection of the Forward Service Door Cutout Aft Lower Corner Fuselage Skin and Bear Strap
Refer to the listed
procedures in SB
767-53A0301
original issue or
later approved re-
visions as an ac-
cepted proce-
dure.
Method of ComplianceActionCondition
(b) It is not required to do the inspections in accordance with Requirements Bulletin RB in areas where a
repair covers the affected inspection area and meets any of the following conditions:
1. The repair is the corrective action to the crack condition identified in Requirements Bulletin 767-
53A0301 RB and installed after the Original Issue date of Requirements Bulletin 767-53A0301
RB.
2. The repair was approved by the Boeing Organization Designation Authorization (ODA) via an
FAA Form 8100-9 which contains a repeat inspection program for the subject area.
(c) Accomplishment of the SRM Repair 1 is terminating action for the inspections at this location only.
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 21, 2021
767-53A0301 RBRevision 2: May 24, 2023
26 of 44
REQUIREMENTS BULLETIN 767-53A0301
ALERTALERT

### Page 27 (OCR)

REQUIREMENTS BULLETIN 767-53A0301
ALERT  ALERT
STA
340
EDGE OF  SKIN
THE LOWER
MAIN SILL
CHORD
FORWARD ENTRY DOOR
2945907
FIGURE 1: FORWARD ENTRY DOOR CUTOUT AFT LOWER CORNER FUSELAGE SKIN AND BEAR STRAP
- EXTERNAL AND INTERNAL DETAILED INSPECTION
(SHEET 1 OF 4)
Original Issue: April 21, 2021
Revision 2 May 24, 2023  Export Controlled ECCN: 9E991  767-53A0301 RB
Copyright © Unpublished Work - See page 1 for details.  27 of 44

### Page 28 (OCR)

REQUIREMENTS BULLETIN 767-53A0301
ALERT  ALERT
- 0.6  0.5l
SKIN-
761-S -
0.60
0.50
S-20L
EDGE OF
THE LOWER
MAIN SILL
CHORD
- S-21L
TYPICAL CRACK
STA  STA  STA  STA
325  332  340  347
FWD
VIEW LOOKING INBOARD
FORWARD ENTRY DOOR CUTOUT
AFT LOWER CORNER
A-A
DETAILED INSPECTION
2957083
FIGURE 1: FORWARD ENTRY DOOR CUTOUT AFT LOWER CORNER FUSELAGE SKIN AND BEAR STRAP
- EXTERNAL AND INTERNAL DETAILED INSPECTION
(SHEET 2 OF 4)
Original Issue: April 21, 2021
Revision 2 May 24, 2023  767-53A0301 RB
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.  28 of 44

### Page 29 (OCR)

REQUIREMENTS BULLETIN 767-53A0301
ALERT  ALERT
STA
340
0.60
0.50
S-19L -
2)
- TYPICAL CRACK
STA
332
• o  C
FWD
VIEW LOOKING OUTBOARD
FORWARD ENTRY DOOR CUTOUT
AFT LOWER CORNER
DETAILED INSPECTION
2957084
FIGURE 1: FORWARD ENTRY DOOR CUTOUT AFT LOWER CORNER FUSELAGE SKIN AND BEAR STRAP
- EXTERNAL AND INTERNAL DETAILED INSPECTION
(SHEET 3 OF 4)
Original Issue: April 21, 2021
Revision 2 May 24, 2023  Export Controlled ECCN: 9E991  767-53A0301 RB
Copyright © Unpublished Work - See page 1 for details.  29 of 44

### Page 30

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
More DataQtyIdentificationNameTaskStep
(a)--SKINInspect1
(b)--BEAR STRAPInspect2
(a) Do an external detailed inspection of the Fuselage skin at the Forward Entry Door Cutout Aft lower corner
area for any crack.
(b) Do an internal detailed inspection of the bear strap for any crack.
FIGURE 1: FORWARD ENTRY DOOR CUTOUT AFT LOWER CORNER FUSELAGE SKIN AND BEAR STRAP
- EXTERNAL AND INTERNAL DETAILED INSPECTION
(SHEET 4 OF 4)
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 21, 2021
767-53A0301 RBRevision 2 May 24, 2023
30 of 44
REQUIREMENTS BULLETIN 767-53A0301
ALERTALERT

### Page 31 (OCR)

REQUIREMENTS BULLETIN 767-53A0301
ALERT  ALERT
This Figure applies only to: Group 1.
STA  VUL
340
STA
293
EWD
SKIN  EDGE OF  THE LOWER
MAIN SILL
CHORD
FORWARD SERVICE DOOR
2945910
FIGURE 2: FORWARD SERVICE DOOR CUTOUT AFT LOWER CORNER FUSELAGE SKIN AND BEAR
STRAP - EXTERNAL AND INTERNAL DETAILED INSPECTION
(SHEET 1 OF 4)
Original Issue: April 21, 2021
Revision 2 May 24, 2023  Export Controlled ECCN: 9E991  767-53A0301 RB
Copyright © Unpublished Work - See page 1 for details.  31 of 44

### Page 32 (OCR)

REQUIREMENTS BULLETIN 767-53A0301
ALERT  ALERT
0.60
0.50  - SKIN
0.60
0.50
S-19R -
S-20R -
EDGE OF
THE
-LOWER
MAIN
SILL
CHORD
S-21R -
TYPICAL CRACK
STA  STA  STA
347  340  332
FWD
VIEW LOOKING INBOARD
FORWARD SERVICE DOOR CUTOUT
AFT LOWER CORNER
DETAILED INSPECTION  A-A
2957090
FIGURE 2: FORWARD SERVICE DOOR CUTOUT AFT LOWER CORNER FUSELAGE SKIN AND BEAR
STRAP - EXTERNAL AND INTERNAL DETAILED INSPECTION
(SHEET 2 OF 4)
Original Issue: April 21, 2021
Revision 2 May 24, 2023  767-53A0301 RB
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.  32 of 44

### Page 33 (OCR)

REQUIREMENTS BULLETIN 767-53A0301
ALERT  ALERT
STA
340
0.60
0.50
- S-19R
TYPICAL CRACK -
STA
332
FWD
VIEW LOOKING OUTBOARD
FORWARD SERVICE DOOR CUTOUT
AFT LOWER CORNER
DETAILED INSPECTION
2957091
FIGURE 2: FORWARD SERVICE DOOR CUTOUT AFT LOWER CORNER FUSELAGE SKIN AND BEAR
STRAP - EXTERNAL AND INTERNAL DETAILED INSPECTION
(SHEET 3 OF 4)
Original Issue: April 21, 2021
Revision 2 May 24, 2023  Export Controlled ECCN: 9E991  767-53A0301 RB
Copyright © Unpublished Work - See page 1 for details.  33 of 44

### Page 34

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
More DataQtyIdentificationNameTaskStep
(a)--SKINInspect1
(b)--BEAR STRAPInspect2
(a) Do an external detailed inspection of the Fuselage skin at the Forward Service Door Cutout Aft lower
corner area for any crack.
(b) Do an internal detailed inspection of the bear strap for any crack.
FIGURE 2: FORWARD SERVICE DOOR CUTOUT AFT LOWER CORNER FUSELAGE SKIN AND BEAR
STRAP - EXTERNAL AND INTERNAL DETAILED INSPECTION
(SHEET 4 OF 4)
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 21, 2021
767-53A0301 RBRevision 2 May 24, 2023
34 of 44
REQUIREMENTS BULLETIN 767-53A0301
ALERTALERT

### Page 35 (OCR)

REQUIREMENTS BULLETIN 767-53A0301
ALERT  ALERT
STA
340
STA
293
EDGE OF  SKIN
THE LOWER?
MAIN SILL
CHORD
FORWARD ENTRY DOOR
2944482
FIGURE 3: FORWARD ENTRY DOOR CUTOUT AFT LOWER CORNER FASTENER HOLE LOCATIONS -
OPEN HOLE HIGH FREQUENCY EDDY CURRENT (HFEC) INSPECTION
(SHEET 1 OF 3)
Original Issue: April 21, 2021
Revision 2 May 24, 2023  Export Controlled ECCN: 9E991  767-53A0301 RB
Copyright © Unpublished Work - See page 1 for details.  35 of 44

### Page 36 (OCR)

REQUIREMENTS BULLETIN 767-53A0301
ALERT  ALERT
SKIN ~
- S-19L
5 LOCATIONS
- S-20L
EDGE OF
THE
LOWER
MAIN SILL
CHORD
- S-21L
STA  325  STA  332  TYPICAL CRACK  STA  340  SIA  347
FWD
VIEW LOOKING INBOARD
FORWARD ENTRY DOOR CUTOUT
AFT LOWER CORNER
A-A
2957093
FIGURE 3: FORWARD ENTRY DOOR CUTOUT AFT LOWER CORNER FASTENER HOLE LOCATIONS -
OPEN HOLE HIGH FREQUENCY EDDY CURRENT (HFEC) INSPECTION
(SHEET 2 OF 3)
Original Issue: April 21, 2021
Revision 2 May 24, 2023  767-53A0301 RB
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.  36 of 44

### Page 37

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
More DataQtyIdentificationNameTaskStep
(a)5-FASTENER HOLESInspect1
(a) Do an open hole High Frequency Eddy Current (HFEC) Inspection of the fastener holes at the Forward
Entry Door Cutout Aft lower corner for any crack in accordance with 767 NDT Manual Part 6, 51-00-16.
FIGURE 3: FORWARD ENTRY DOOR CUTOUT AFT LOWER CORNER FASTENER HOLE LOCATIONS -
OPEN HOLE HIGH FREQUENCY EDDY CURRENT (HFEC) INSPECTION
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 21, 2021
767-53A0301 RBRevision 2 May 24, 2023
37 of 44
REQUIREMENTS BULLETIN 767-53A0301
ALERTALERT

### Page 38 (OCR)

REQUIREMENTS BULLETIN 767-53A0301
ALERT  ALERT
This Figure applies only to: Group 1.
STA  VUL
340
STA
293
SKIN  • EDGE OF  THE LOWER
MAIN SILL
CHORD
FORWARD SERVICE DOOR
2944520
FIGURE 4: FORWARD SERVICE DOOR CUTOUT AFT LOWER CORNER FASTENER HOLE LOCATIONS
- OPEN HOLE HIGH FREQUENCY EDDY CURRENT (HFEC) INSPECTION
(SHEET 1 OF 3)
Original Issue: April 21, 2021
Revision 2 May 24, 2023  Export Controlled ECCN: 9E991  767-53A0301 RB
Copyright © Unpublished Work - See page 1 for details.  38 of 44

### Page 39 (OCR)

REQUIREMENTS BULLETIN 767-53A0301
ALERT  ALERT
- SKIN
S-19R -
5 LOCATIONS
S-20R
EDGE OF
THE
-LOWER
MAIN SILL
CHORD
S-21R
STA  TYPICAL CRACK  STA
347  325
-WD
VIEW LOOKING INBOARD
FORWARD SERVICE DOOR CUTOUT
AFT LOWER CORNER
A-A
2957094
FIGURE 4: FORWARD SERVICE DOOR CUTOUT AFT LOWER CORNER FASTENER HOLE LOCATIONS
- OPEN HOLE HIGH FREQUENCY EDDY CURRENT (HFEC) INSPECTION
(SHEET 2 OF 3)
Original Issue: April 21, 2021
Revision 2 May 24, 2023  Export Controlled ECCN: 9E991  767-53A0301 RB
Copyright © Unpublished Work - See page 1 for details.  39 of 44

### Page 40

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
More DataQtyIdentificationNameTaskStep
(a)5-FASTENER HOLESInspect1
(a) Do an open hole High Frequency Eddy Current (HFEC) Inspection of the fastener holes at the Forward
Service Door Cutout Aft lower corner for any crack in accordance with 767 NDT Manual Part 6, 51-00-
16.
FIGURE 4: FORWARD SERVICE DOOR CUTOUT AFT LOWER CORNER FASTENER HOLE LOCATIONS
- OPEN HOLE HIGH FREQUENCY EDDY CURRENT (HFEC) INSPECTION
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 21, 2021
767-53A0301 RBRevision 2 May 24, 2023
40 of 44
REQUIREMENTS BULLETIN 767-53A0301
ALERTALERT

### Page 41 (OCR)

REQUIREMENTS BULLETIN 767-53A0301
ALERT  ALERT
STA
340
STA  SCUFF PLATE
293
EDGE OF  SKIN
THE LOWER*
MAIN SILL
CHORD
FORWARD ENTRY DOOR
2944596
FIGURE 5: FORWARD ENTRY DOOR CUTOUT AFT LOWER CORNER FUSELAGE SKIN - EXTERNAL
DETAILED INSPECTION
(SHEET 1 OF 2)
Original Issue: April 21, 2021
Revision 2 May 24, 2023  Export Controlled ECCN: 9E991  767-53A0301 RB
Copyright © Unpublished Work - See page 1 for details.  41 of 44

### Page 42 (OCR)

REQUIREMENTS BULLETIN 767-53A0301
ALERT  ALERT
0.60
0.50  .0.60
0.50
- S-19L
SKIN
1.86
SCUFF PLATE  1.76
S-20L
LOWER MAIN -  EDGE OF THE  1- +
SILL CHORD
STA
340
STA
325  FWD
VIEW LOOKING INBOARD
FORWARD ENTRY DOOR CUTOUT
AFT LOWER CORNER
DETAILED INSPECTION  A-A
2944496
The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
Step  Task  Name  Identification  Qty  More Data
Inspect  SKIN  (a)
(a) Do an external detailed inspection of the skin for any crack.
FIGURE 5: FORWARD ENTRY DOOR CUTOUT AFT LOWER CORNER FUSELAGE SKIN - EXTERNAL
DETAILED INSPECTION
(SHEET 2 OF 2)
Original Issue: April 21, 2021
Revision 2 May 24, 2023  Export Controlled ECCN: 9E991  767-53A0301 RB
Copyright © Unpublished Work - See page 1 for details.  42 of 44

### Page 43 (OCR)

REQUIREMENTS BULLETIN 767-53A0301
ALERT  ALERT
This Figure applies only to: Group 1.
STA
340
JUL
%
- SCUFF PLATE  STA
293
SKIN  • THE LOWEF  EDGE OI
MAIN SILL
CHORD
FORWARD SERVICE DOOR
2944608
FIGURE 6: FORWARD SERVICE DOOR CUTOUT AFT LOWER CORNER FUSELAGE SKIN - EXTERNAL
DETAILED INSPECTION
(SHEET 1 OF 2)
Original Issue: April 21, 2021
Revision 2 May 24, 2023  Export Controlled ECCN: 9E991  767-53A0301 RB
Copyright © Unpublished Work - See page 1 for details.  43 of 44

### Page 44 (OCR)

REQUIREMENTS BULLETIN 767-53A0301
ALERT  ALERT
0.60
0.60  0.50
0.50
S-19R -
- SKIN
1.86
1.76  SCUFF PLATE
S-20R
-H - LOWER MAIN  EDGE OF THE
SILL CHORD
STA
340
STA
325
FWD
VIEW LOOKING INBOARD
FORWARD SERVICE DOOR CUTOUT
AFT LOWER CORNER
DETAILED INSPECTION  A-A
2944609
The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
Step  Task  Name  Identification  Qty  More Data
Inspect  SKIN  (a)
(a) Do an external detailed inspection of the skin for any crack.
FIGURE 6: FORWARD SERVICE DOOR CUTOUT AFT LOWER CORNER FUSELAGE SKIN - EXTERNAL
DETAILED INSPECTION
(SHEET 2 OF 2)
Original Issue: April 21, 2021
Revision 2 May 24, 2023  Export Controlled ECCN: 9E991  767-53A0301 RB
Copyright © Unpublished Work - See page 1 for details.  44 of 44

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
