# Boeing Alert Service Bulletin 767-57A0122: No revision named

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2010-0762; AD 2010-17-03 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Alert Service Bulletin 767-57A0122](https://openairdocs.org/service-documents/boeing/767-57a0122.md)
- Title as filed: U.S. DOT/FAA - Boeing Service Bulletin
- Pages: 19
- PDF: https://openairdocs.org/files/sha256/0c/25/0c25986fb43aab36a22a12f67447da285b028b95a92c540926bc08bc565b980d
- Page: https://openairdocs.org/service-documents/boeing/767-57a0122/file/0c25986fb43a

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Commercial 
Airplanes
767
Service Bulletin
ALERT
Number: 767-57A0122
Original Issue: October 22, 2009
ATA System: 5710
SUBJECT: WINGS - Center Wing - Sleeve and Clamp Installation
Export of this technology is controlled under the United States Export Administration Regulations (EAR) (15
CFR 730-774). An export license may be required before it is used for development, production or use by foreign
persons from specific countries. The controller of this data has the individual responsibility to abide by all export
laws.
9E991ECCN:
BOEING PROPRIETARY, CONFIDENTIAL, AND/OR TRADE SECRET
Copyright © 2009 The Boeing Company
Unpublished Work - All Rights Reserved
Boeing claims copyright in each page of this document only to the extent that the page contains copyrightable
subject matter. Boeing also claims copyright in this document as a compilation and/or collective work.
This document includes proprietary information owned by The Boeing Company and/or one or more third parties.
Treatment of the document and the information it contains is governed by contract with Boeing. For more
information, contact The Boeing Company, P.O. Box 3707, Seattle, Washington 98124.
Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner,
BBJ, DC-8, DC-9, DC-10, KC-10, KDC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8A, Poseidon and the
Boeing livery are all trademarks owned by The Boeing Company; and no trademark license is granted in
connection with this document unless provided in writing by Boeing.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: October 22, 2009
767-57A0122
1 of 19
5.0

### Page 2

BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: October 22, 2009
767-57A0122
2 of 19
BOEING SERVICE BULLETIN 767-57A0122
ALERTALERT
BLANK PAGE

### Page 3

Table of Contents
Summary ...................................................... 5
1. PLANNING INFORMATION ........................................ 9
A. Effectivity ................................................ 9
1. Airplanes ............................................. 9
2. Spares Affected ......................................... 9
B. Concurrent Requirements ....................................... 9
C. Reason ................................................ 1 0
D. Description .............................................. 1 0
E. Compliance .............................................. 1 0
F. Approval ............................................... 1 1
G. Manpower .............................................. 1 1
H. Weight and Balance Changes .................................... 1 1
I. Electrical Load Data ......................................... 1 1
J. References .............................................. 1 2
1. Existing Data .......................................... 1 2
2. Data supplied with this Service Bulletin ............................ 1 2
3. Installation Drawings Used in the Preparation of this Service Bulletin ............ 1 2
K. Publications Affected ........................................ 1 2
L. Interchangeability and Intermixability of Parts ........................... 1 2
2. MATERIAL INFORMATION ........................................ 1 3
A. Material - Price and Availability ................................... 1 3
B. Industry Support Information .................................... 1 3
C. Parts Necessary For Each Airplane ................................. 1 3
1. Kits/Parts ............................................ 1 3
2. Parts and Materials Supplied by the Operator ........................ 1 4
3. Parts Modified and Reidentified ................................ 1 4
4. Parts Removed and Not Replaced .............................. 1 4
D. Parts Necessary to Change Spares ................................. 1 4
E. Special Tooling - Price and Availability ............................... 1 4
F. Special Tooling Necessary to do this Service Bulletin ....................... 1 4
3. ACCOMPLISHMENT INSTRUCTIONS .................................. 1 5
A. GENERAL INFORMATION ..................................... 1 5
B. WORK INSTRUCTIONS ....................................... 1 5
FIGURE 1: REAR SPAR - RIGHT MAIN WHEEL WELL - SLEEVE AND CLAMP INSTALLATION . . 17
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: October 22, 2009
767-57A0122
3 of 19
BOEING SERVICE BULLETIN 767-57A0122
ALERTALERT

### Page 4

BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: October 22, 2009
767-57A0122
4 of 19
BOEING SERVICE BULLETIN 767-57A0122
ALERTALERT
BLANK PAGE

### Page 5

Commercial 
Airplanes
767
Service Bulletin
ALERT
SummaryNumber: 767-57A0122Original Issue: October 22, 2009
ATA System: 5710
SUBJECT: WINGS - Center Wing - Sleeve and Clamp Installation
THIS BULLETIN IS SENT TO THE OPERATORS OF RECORD OF THE AIRPLANES SHOWN IN PARAGRAPH
1.A., EFFECTIVITY. IF AN AIRPLANE HAS BEEN LEASED OR SOLD, SEND THIS SERVICE BULLETIN TO
THE NEW OPERATOR. IF APPLICABLE SPARES HAVE BEEN SOLD, SEND THIS SERVICE BULLETIN TO
THE NEW OWNER.
CONCURRENT REQUIREMENTS
None.
BACKGROUND
Accomplishment of the modifications within this service bulletin will help prevent possible ignition sources in the
center auxiliary fuel tank caused by a wiring short. An ignition source in a fuel tank could result in a fire or an
explosion.
A safety assessment by Boeing identified a certain type of fastener that penetrates the fuel tank wall and has
an insufficient electrical bond to the fuel tank structure. These fasteners can be a path for electrical energy to
enter the fuel tank if a wiring short occurs in a wire bundle installed along the fuel tank boundary structure. The
electrical energy from the wiring short can go through these fasteners because they have an insufficient bond
to the fuel tank structure. This energy can be sufficient to cause arcing at the ends of these fasteners in the fuel
tank. The necessary changes were incorporated in production by PRRB13421-11. A review of the production
records found that three airplanes did not met the production requirements. On these three airplanes, there is
one location on the rear spar of the center wing fuel tank where the specified tetrafluoroethylene (TFE 2X) sleeve
and clamp change was not accomplished.
This Service Bulletin makes these changes at one location on the rear spar of the center wing where a high
energy short can occur. A TFE 2X sleeve on the wire bundle gives more protection from chafing. The wire bundle
clamps has a design with protection on its metal edges. These changes make sure that the risk of an ignition
source in the fuel tank from a short is kept to a minimum.
This service bulletin is the result of the safety assessments conducted by Boeing under SFAR 88, "Fuel Tank
System Fault Tolerance Evaluation Requirements".
ACTION
Get access to the rear spar of the center wing in the main wheel well on the right side and install the TFE 2X
sleeve and the full cushion wire bundle clamp at one location.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: October 22, 2009
767-57A0122
5 of 19

### Page 6

EFFECTIVITY
767-300 Airplanes. Refer to Paragraph 1.A.1., Airplanes for the list of affected airplanes.
COMPLIANCE
The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to this service
bulletin. The Airworthiness Directive will make the compliance tasks and times given in this service bulletin
mandatory.
Boeing recommends that this service bulletin be incorporated within 5 years after the original issue date on this
service bulletin.
INDUSTRY SUPPORT INFORMATION
Boeing warranty remedies are available for airplanes in warranty as of November 18, 2008. Please refer to
Paragraph 2.B., Industry Support Information.
MANPOWER
Elapsed HoursTotal Task HoursAirplanes
2.502.50All
MATERIAL INFORMATION
Boeing Supplied Kits/Parts.
Refer to Paragraph 2.A., Material - Price and Availability.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: October 22, 2009
767-57A0122
6 of 19
BOEING SERVICE BULLETIN 767-57A0122
ALERTALERT

### Page 7 (OCR)

BOEING SERVICE BULLETIN 767-57A0122
ALERT  ALERT
STA
955
INSTALL THE TFE SLEEVE
AND FULL CUSHION CLAMP
ON THE WIRE BUNDLE
1834099
Original Issue: October 22, 2009
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.  7 of 19

### Page 8

BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: October 22, 2009
767-57A0122
8 of 19
BOEING SERVICE BULLETIN 767-57A0122
ALERTALERT
BLANK PAGE

### Page 9

Commercial 
Airplanes
767
Service Bulletin
ALERT
Number: 767-57A0122
Original Issue: October 22, 2009
ATA System: 5710
SUBJECT: WINGS - Center Wing - Sleeve and Clamp Installation
THIS BULLETIN IS SENT TO THE OPERATORS OF RECORD OF THE AIRPLANES SHOWN IN PARAGRAPH
1.A., EFFECTIVITY. IF AN AIRPLANE HAS BEEN LEASED OR SOLD, SEND THIS SERVICE BULLETIN TO
THE NEW OPERATOR. IF APPLICABLE SPARES HAVE BEEN SOLD, SEND THIS SERVICE BULLETIN TO
THE NEW OWNER.
1.    PLANNING INFORMATION
A. Effectivity
1. Airplanes
Refer to Service Bulletin Index Document D624T001 Part 3 for Airplane Variable Number, Line
Number, and Serial Number data.
This service bulletin is for the airplanes shown below.
DESCRIPTIONCONFIGURATIONGROUP
767-300-1
Airplane Models:
767-300
GroupVariable Number
1VS911 - VS912
1VS916
2. Spares Affected
None.
B. Concurrent Requirements
None.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: October 22, 2009
767-57A0122
9 of 19

### Page 10

C. Reason
Accomplishment of the modifications within this service bulletin will help prevent possible ignition
sources in the center auxiliary fuel tank caused by a wiring short. An ignition source in a fuel tank could
result in a fire or an explosion.
A safety assessment by Boeing identified a certain type of fastener that penetrates the fuel tank wall
and has an insufficient electrical bond to the fuel tank structure. These fasteners can be a path for
electrical energy to enter the fuel tank if a wiring short occurs in a wire bundle installed along the fuel
tank boundary structure. The electrical energy from the wiring short can go through these fasteners
because they have an insufficient bond to the fuel tank structure. This energy can be sufficient to cause
arcing at the ends of these fasteners in the fuel tank. The necessary changes were incorporated in
production by PRRB13421-11. A review of the production records found that three airplanes did not
met the production requirements. On these three airplanes, there is one location on the rear spar of
the center wing fuel tank where the specified tetrafluoroethylene (TFE 2X) sleeve and clamp change
was not accomplished.
This Service Bulletin makes these changes at one location on the rear spar of the center wing where
a high energy short can occur. A TFE 2X sleeve on the wire bundle gives more protection from chafing.
The wire bundle clamps has a design with protection on its metal edges. These changes make sure
that the risk of an ignition source in the fuel tank from a short is kept to a minimum.
This service bulletin is the result of the safety assessments conducted by Boeing under SFAR 88, "Fuel
Tank System Fault Tolerance Evaluation Requirements".
D. Description
Get access to the rear spar of the center wing in the main wheel well on the right side and install the
TFE 2X sleeve and the full cushion clamp on the wire bundle at one location.
The work in this service bulletin is done in the maintenance zone(s) given below.
Affected Maintenance Zones
ZoneModel
144767-300
E. Compliance
The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to
this service bulletin. The Airworthiness Directive will make the compliance tasks and times given in this
service bulletin mandatory.
Boeing recommends that the change given in this service bulletin be done within 5 years after the
original issue date on this service bulletin.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: October 22, 2009
767-57A0122
10 of 19
BOEING SERVICE BULLETIN 767-57A0122
ALERTALERT

### Page 11

F. Approval
This service bulletin was examined by the Federal Aviation Administration (FAA). The changes specified
in this service bulletin comply with the applicable regulations and are FAA approved, as well as European
Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved
airplanes listed in the service bulletin effectivity. This service bulletin and its approval were based on
the airplane in its original Boeing delivery configuration or as modified by other approved Boeing
changes.
If an airplane has a non-Boeing modification or repair that affects a component or system also affected
by this service bulletin, the operator is responsible for obtaining appropriate regulatory agency approval
before incorporating this service bulletin.
G. Manpower
The table below shows an estimate of the task hours necessary to do this change for each airplane.
This estimate is for direct labor only, done by an experienced crew. Adjust the estimate with operator
task hour data if necessary. The estimate does not include lost time. These are some examples of lost
time:
 Time to adjust to the workplace
 Time to schedule the work
 Time to inspect the work
 Time to cure the materials
 Time to make the parts
 Time to find the tools.
Elapsed HoursTask HoursNumber of Per-
sons
Task
1.001.001Open Access
0.500.501Figure 1
1.001.001Close Access
2.502.50TOTAL FOR EACH AIRPLANE
H. Weight and Balance Changes
None.
I. Electrical Load Data
Not changed.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: October 22, 2009
767-57A0122
11 of 19
BOEING SERVICE BULLETIN 767-57A0122
ALERTALERT

### Page 12

J. References
1. Existing Data
a. Standard Wiring Practices Manual (SWPM) 20-10-11, 20-10-12, 20-10-19
b. 767 Aircraft Maintenance Manual (AMM) 24-22-00, 32-00-15, 32-00-20
c. Engineering Change Memo PRRB13421-11
2. Data supplied with this Service Bulletin
None.
3. Installation Drawings Used in the Preparation of this Service Bulletin
TitleDrawing Number
Wire Bundle Installation Wheel Well Area Right, STA 955 Thru 1065288T4570
These drawings were used to prepare this service bulletin. These drawings are not necessary to
make the specified changes, and are not supplied with this service bulletin. These drawings may
not be applicable to all airplane configurations or operators.
K. Publications Affected
1. Publications:
None.
2. Damage Tolerance Based Structural Inspections:
Boeing has evaluated the repairs and/or changes in this service bulletin for effects on Fatigue
Critical Structure (FCS) and for changes to Damage Tolerance Inspections (DTI) required in the
Maintenance Program. This service bulletin does not affect FCS, therefore DTIs are not necessary.
L. Interchangeability and Intermixability of Parts
Accomplishment of this service bulletin does not affect interchangeability or intermixability of parts.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: October 22, 2009
767-57A0122
12 of 19
BOEING SERVICE BULLETIN 767-57A0122
ALERTALERT

### Page 13

2.    MATERIAL INFORMATION
A. Material - Price and Availability
Boeing can supply the kits shown in Paragraph 2.C., Parts Necessary for Each Airplane as shown
below. If there is a limit to the quantity (QTY) of available kits, a supply sequence is given by Spares.
More kits become available as shown in the Reorder Lead Time (ROLT). ROLT is calculated from the
date Boeing gets the purchase order.
Unit Price thru
Apr 31/10
ROLT
(Weeks)
QTYDateNameKit Number
$ 189.0013305/21/2009Top Kit015T1842-1
The kits are subject to the terms and conditions of the Boeing standard purchase order acknowledgment.
After the Unit Price date, new price and ROLT data is applicable. Prices are in United States dollars.
Terms: Net 30 days.
Reference this service bulletin and submit your purchase order by one of the methods that follow:
1. Order on-line via ATA Spec 2000 or Boeing Part Page
2. Fax to (206) 662-7145
3. Mail to:
Spares Customer Support - MC 36-65
Boeing Spares Department
P.O. Box 3707
Seattle, Washington 98124-2207 USA
B. Industry Support Information
Boeing warranty remedies are available for 767 airplanes in warranty as of November 18, 2008. For
task hour reimbursement for airplanes in warranty as of that date, send a warranty claim to Boeing
Commercial Airplanes Group - Warranties. The kits for airplanes in warranty as of that date will be
supplied at no charge. Send a purchase order for the kits to Boeing Spares. Please refer to this service
bulletin number and reference the airplane variable numbers in your purchase order.
C. Parts Necessary For Each Airplane
1. Kits/Parts
To get the kits/parts shown below, refer to Paragraph 2.A., Material - Price and Availability.
NOTE: One top kit and the items shown in Paragraph 2.C.2., Parts and Materials Supplied by
the Operator, are necessary for each airplane. The Top Kit is divided into Figure kits for
each installation figure shown in the table below.
To get the kits/parts shown below, refer to Paragraph 2.A., Material - Price and Availability.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: October 22, 2009
767-57A0122
13 of 19
BOEING SERVICE BULLETIN 767-57A0122
ALERTALERT

### Page 14

Figure Kit
1Top Kit
1015T1842-1
Group 1:
KIT 015T1842-1
NOTES
Existing Part
NumberName
Figure
New Part Number
1
QTY
Sleeve - 1 inch I.D.
(As supplied 1.5
inch I.D.)
1005W3281-5
WIRE BUNDLE
CLAMP
1BACC10JU106
2. Parts and Materials Supplied by the Operator
NotesNameQTYPart Number/ Specification
(a)LACING TAPE3 ftBMS 13-54, TYPE III, CLASS
1, FINISH C, WHITE
(a) See the Qualified Products List at the end of the Boeing Material Specification (BMS) for
supplier data.
3. Parts Modified and Reidentified
None.
4. Parts Removed and Not Replaced
None.
D. Parts Necessary to Change Spares
None.
E. Special Tooling - Price and Availability
None.
F. Special Tooling Necessary to do this Service Bulletin
No special tools or equipment are necessary to do the change in this service bulletin. But, maintenance
and overhaul tools in the manuals given in Paragraph 1.J., References, can be necessary. Examine
operator tool supply to make sure all necessary tools are available.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: October 22, 2009
767-57A0122
14 of 19
BOEING SERVICE BULLETIN 767-57A0122
ALERTALERT

### Page 15

3.    ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL INFORMATION
CAUTION: KEEP THE WORK AREA, WIRES AND ELECTRICAL BUNDLES CLEAN OF METAL
PARTICLES OR CONTAMINATION WHEN YOU USE TOOLS. UNWANTED MATERIAL,
METAL PARTICLES OR CONTAMINATION CAUGHT IN WIRE BUNDLES CAN CAUSE
DAMAGE TO THE BUNDLES. DAMAGED WIRE BUNDLES CAN CAUSE SPARKS OR
OTHER ELECTRICAL DAMAGE.
NOTE: 1. The instructions identified in Paragraph 3.B., Work Instructions and the Figure give
the recommended sequence of steps. The sequence of steps to do this service
bulletin can be changed.
2. Manual titles are referred to by acronyms. Refer to Paragraph 1.J., References, for
definition of the acronyms.
3. Obey all of the warnings and cautions given in the specified manual sections.
4. Unless shown differently, these dimensions and tolerances are used:
– Linear dimensions are in inches
– Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus
or minus 0.03 inch
– Tolerance on rivet and bolt edge margin is plus or minus 0.05 inch
– Torque limits to tighten nuts and bolts are in 767 SRM, Chapter 51
5. Refer to the SWPM 20-10-11 and SWPM 20-10-12 for the wire installation procedures,
and SWPM 20-10-19 for the wire separation requirements, as accepted procedures.
6. These work instructions refer to procedures included in other Boeing documents.
When the words "refer to" are used and the operator has an accepted alternative
procedure, the accepted alternative procedure can be used. When the words "in
accordance with" are included in the instruction, the procedure in the Boeing document
must be used.
B. WORK INSTRUCTIONS
1. Remove electrical power from the airplane. Refer to 767 AMM 24-22-00 as an accepted procedure.
2. Install the downlocks on the nose and main landing gear. Refer to 767 AMM 32-00-20 as an
accepted procedure.
3. Install the door locks on the nose and main landing gear. Refer to 767 AMM 32-00-15 as an
accepted procedure.
4. Get access to the rear spar at the main wheel well on the right side of the airplane.
5. Install the tetrafluoroethylene (TFE 2X) sleeve and clamp in accordance with Figure 1.
6. Remove the door locks on the nose and main landing gear. Refer to 767 AMM 32-00-15 as an
accepted procedure.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: October 22, 2009
767-57A0122
15 of 19
BOEING SERVICE BULLETIN 767-57A0122
ALERTALERT

### Page 16

7. Remove the downlocks on the nose and main landing gear. Refer to 767 AMM 32-00-20 as an
accepted procedure.
8. Restore electrical power to the airplane. Refer to 767 AMM 24-22-00 as an accepted procedure.
9. Put the airplane back to a serviceable condition.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: October 22, 2009
767-57A0122
16 of 19
BOEING SERVICE BULLETIN 767-57A0122
ALERTALERT

### Page 17 (OCR)

BOEING SERVICE BULLETIN 767-57A0122
ALERT  ALERT
STA
955
W932
1834106
FIGURE 1: REAR SPAR - RIGHT MAIN WHEEL WELL - SLEEVE AND CLAMP INSTALLATION
(SHEET 1 OF 3)
Original Issue: October 22, 2009
BOEING PROPRIETARY -  767-57A0122
Copyright © Unpublished Work - See page 1 for details.  17 of 19

### Page 18 (OCR)

BOEING SERVICE BULLETIN 767-57A0122
ALERT  ALERT
0.25
2 4
0.25
2.75-3.00
SUPPORT
BRACKET
.0.25  INBD
0.25
WIRE
BUNDLE
W932
CLAMP INSTALLATION
(TYPICAL)
WIRE
BUNDLE
50 PERCENT
OVERLAP
MINIMUM
SLEEVE
1834144
FIGURE 1: REAR SPAR - RIGHT MAIN WHEEL WELL - SLEEVE AND CLAMP INSTALLATION
(SHEET 2 OF 3)
Original Issue: October 22, 2009
BOEING PROPRIETARY -  767-57A0122
Copyright © Unpublished Work - See page 1 for details.  18 of 19

### Page 19

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
1-SCREWRemove / Keep1
1-WASHERRemove / Keep
If a spacer is in-
stalled.
1-SPACERRemove / Keep
It is not necessary to
remove the nut if it
is attached to the
bracket.
1-NUTRemove / Keep
1-CLAMPRemove2
Sleeve is TFE 2X.
Cut the sleeve to the
requirement length
is necessary.
--SLEEVECut3
Sleeve is TFE 2X.
Cut the sleeve longi-
tudinally for installa-
tion on the wire bun-
dle.
--SLEEVECut
Sleeve is TFE 2X.1005W3281-5Sleeve - 1 inch I.D. (As
supplied 1.5 inch I.D.)
Install (New)
Refer to SWPM 20-
10-12 as an accept-
ed procedure for in-
stallation of wire
bundle support
clamp.
1BACC10JU106WIRE BUNDLE
CLAMP
Install (New)4
1-WASHERInstall (Kept)5
1-SCREWInstall (Kept)
1-SPACERInstall (Kept)
1-NUTInstall (Kept)
Install in shaded
area. Refer to SW-
PM 20-10-11 as an
accepted procedure
to install a wire har-
ness tie.
-BMS 13-54, TYPE III,
CLASS 1, FINISH C,
WHITE
LACING TAPEInstall (New)6
FIGURE 1: REAR SPAR - RIGHT MAIN WHEEL WELL - SLEEVE AND CLAMP INSTALLATION
(SHEET 3 OF 3)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: October 22, 2009
767-57A0122
19 of 19
BOEING SERVICE BULLETIN 767-57A0122
ALERTALERT

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
