# Boeing Alert Requirements Bulletin 767-57A0148 RB: No revision named, part 1 of 3

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2025-0618; AD 2026-05-07 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Alert Requirements Bulletin 767-57A0148 RB](https://openairdocs.org/service-documents/boeing/767-57a0148-rb.md)
- Title as filed: 767-57A0148_RB_original_Part1
- Pages: 294
- PDF: https://openairdocs.org/files/sha256/5a/38/5a38c11d3702fd502001a8112e6e00fbcc063a6e04a843331fc023a1f3abf2cf
- Page: https://openairdocs.org/service-documents/boeing/767-57a0148-rb/file/5a38c11d3702

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Commercial 
Airplanes
767
Requirements Bulletin
ALERT
Number: 767-57A0148 RB
Original Issue: October 10, 2024
ATA System: 5710 5350
SUBJECT: WINGS - Center Wing - Lower Underwing Longeron Fitting Forward Fastener Holes
Inspection
EXPORT CONTROLLED - This technology or software is subject to the U.S. Export Administration Regulations
(EAR), (15 C.F.R. Parts 730-774). No authorization from the U.S. Department of Commerce is required for
export, re-export, in-country transfer, or access EXCEPT to country group E:1 or E:2 countries/persons per
Supp.1 to Part 740 of the EAR.
9E991ECCN:
Copyright © 2024 The Boeing Company
Treatment of this document and its content is governed by contract with Boeing. Rights to use this document
are licensed on a per aircraft basis and such rights may not be transferable. For more information, contact The
Boeing Company.
Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner,
BBJ, DC-8, DC-9, DC-10, KC-10, KC-46, KDC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8, Poseidon and
Boeing liveries are all trademarks owned by The Boeing Company; and no trademark license is granted in
connection with this document unless provided in writing by Boeing.
Original Issue: October 10, 2024
767-57A0148 RB
1 of 416
4.0

### Page 2

Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 10, 2024
767-57A0148 RB
2 of 416
REQUIREMENTS BULLETIN 767-57A0148
ALERTALERT
BLANK PAGE

### Page 3

Table of Contents
1. EFFECTIVITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
A. Airplanes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
B. Spares Affected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2. CONCURRENT REQUIREMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3. COMPLIANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4. APPROVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
5. ACCOMPLISHMENT INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
A. General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
B. Work Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
FIGURE 3: LEFT SIDE UNDERWING LONGERON FITTING - FORWARD LOWER FASTENER HOLES -
INSPECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 265
FIGURE 4: RIGHT SIDE UNDERWING LONGERON FITTING - FORWARD LOWER FASTENER HOLES
- INSPECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 267
FIGURE 5: LEFT SIDE UNDERWING LONGERON FITTING - TENSION BOLT HOLE AND FRONT SPAR
LOWER CHORD - INSPECTION [Group 1, 3-5] . . . . . . . . . . . . . . . . . . . . . . 269
FIGURE 6: RIGHT SIDE UNDERWING LONGERON FITTING - TENSION BOLT HOLE AND FRONT SPAR
LOWER CHORD - INSPECTION [Group 1, 3-5] . . . . . . . . . . . . . . . . . . . . . . 273
FIGURE 7: LEFT SIDE UNDERWING LONGERON FITTING - TENSION BOLT HOLE AND FRONT SPAR
LOWER CHORD - INSPECTION [Group 4, 6-7] . . . . . . . . . . . . . . . . . . . . . . 277
FIGURE 8: RIGHT SIDE UNDERWING LONGERON FITTING - TENSION BOLT HOLE AND FRONT SPAR
LOWER CHORD - INSPECTION [Group 4, 6-7] . . . . . . . . . . . . . . . . . . . . . . 281
FIGURE 9: LEFT SIDE UNDERWING LONGERON FITTING - TENSION BOLT HOLE AND FRONT SPAR
LOWER CHORD - INSPECTION [Group 2] . . . . . . . . . . . . . . . . . . . . . . . . . 285
FIGURE 10: RIGHT SIDE UNDERWING LONGERON FITTING - TENSION BOLT HOLE AND FRONT SPAR
LOWER CHORD - INSPECTION [Group 2] . . . . . . . . . . . . . . . . . . . . . . . . . 289
FIGURE 15: LEFT SIDE UNDERWING LONGERON FITTING P/N 111T4020U7 - TENSION BOLT AND
INTERNAL BATHTUB FITTING - INSTALLATION [Group 1, 3] . . . . . . . . . . . . . . 293
FIGURE 16: RIGHT SIDE UNDERWING LONGERON FITTING P/N 111T4020U8 - TENSION BOLT AND
INTERNAL BATHTUB FITTING - INSTALLATION [Group 1, 3] . . . . . . . . . . . . . . 301
FIGURE 17: LEFT SIDE UNDERWING LONGERON FITTING P/N 111T4020U13 - TENSION BOLT AND
INTERNAL BATHTUB FITTING - INSTALLATION [Group 1, 3] . . . . . . . . . . . . . . 309
FIGURE 18: RIGHT SIDE UNDERWING LONGERON FITTING P/N 111T4020U14 - TENSION BOLT AND
INTERNAL BATHTUB FITTING - INSTALLATION [Group 1, 3] . . . . . . . . . . . . . . 317
FIGURE 19: LEFT SIDE UNDERWING LONGERON FITTING P/N 111T4020U7 - TENSION BOLT AND
INTERNAL BATHTUB FITTING - INSTALLATION [Group 4, 6-7] . . . . . . . . . . . . . 325
FIGURE 20: RIGHT SIDE UNDERWING LONGERON FITTING P/N 111T4020U8 - TENSION BOLT AND
INTERNAL BATHTUB FITTING - INSTALLATION [Group 4, 6-7] . . . . . . . . . . . . . 334
FIGURE 21: LEFT SIDE UNDERWING LONGERON FITTING P/N 111T4020U13 - TENSION BOLT AND
INTERNAL BATHTUB FITTING - INSTALLATION [Group 4, 6-7] . . . . . . . . . . . . . 343
FIGURE 22: RIGHT SIDE UNDERWING LONGERON FITTING P/N 111T4020U14 - TENSION BOLT AND
INTERNAL BATHTUB FITTING - INSTALLATION [Group 4, 6-7] . . . . . . . . . . . . . 351
FIGURE 23: LEFT SIDE UNDERWING LONGERON FITTING P/N 111T4020U9 - TENSION BOLT AND
INTERNAL BATHTUB FITTING - INSTALLATION [Group 2] . . . . . . . . . . . . . . . . 359
FIGURE 24: RIGHT SIDE UNDERWING LONGERON FITTING P/N 111T4020U10 - TENSION BOLT AND
INTERNAL BATHTUB FITTING - INSTALLATION [Group 2] . . . . . . . . . . . . . . . . 367
FIGURE 25: LEFT SIDE UNDERWING LONGERON FITTING P/N 111T4020U15 - TENSION BOLT AND
INTERNAL BATHTUB FITTING - INSTALLATION [Group 2] . . . . . . . . . . . . . . . . 375
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 10, 2024
767-57A0148 RB
3 of 416
REQUIREMENTS BULLETIN 767-57A0148
ALERTALERT

### Page 4

FIGURE 26: RIGHT SIDE UNDERWING LONGERON FITTING P/N 111T4020U16 - TENSION BOLT AND
INTERNAL BATHTUB FITTING - INSTALLATION [Group 2] . . . . . . . . . . . . . . . . 383
FIGURE 27: LEFT SIDE UNDERWING LONGERON FITTING P/N 111T4020U13 - TENSION BOLT AND
INTERNAL BATHTUB FITTING - INSTALLATION [Group 5] . . . . . . . . . . . . . . . . 391
FIGURE 28: RIGHT SIDE UNDERWING LONGERON FITTING P/N 111T4020U14 - TENSION BOLT AND
INTERNAL BATHTUB FITTING - INSTALLATION [Group 5] . . . . . . . . . . . . . . . . 399
FIGURE 33: LEFT SIDE UNDERWING LONGERON FITTING - FORWARD LOWER FASTENERS -
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 407
FIGURE 34: RIGHT SIDE UNDERWING LONGERON FITTING - FORWARD LOWER FASTENERS -
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 410
FIGURE 35: LEFT SIDE UNDERWING LONGERON FITTING - FORWARD LOWER FASTENER HOLES -
CRACK REPAIR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 413
FIGURE 36: RIGHT SIDE UNDERWING LONGERON FITTING - FORWARD LOWER FASTENER HOLES
- CRACK REPAIR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 415
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 10, 2024
767-57A0148 RB
4 of 416
REQUIREMENTS BULLETIN 767-57A0148
ALERTALERT

### Page 5

Commercial 
Airplanes
767
Requirements Bulletin
ALERT
Number: 767-57A0148 RB
Original Issue: October 10, 2024
ATA System: 5710 5350
SUBJECT: WINGS - Center Wing - Lower Underwing Longeron Fitting Forward Fastener Holes
Inspection
THIS DOCUMENT IS SENT TO THE OPERATORS OF RECORD OF THE AIRPLANES SHOWN IN
PARAGRAPH 1.A., EFFECTIVITY. IF AN AIRPLANE HAS BEEN LEASED OR SOLD, SEND THIS DOCUMENT
TO THE NEW OPERATOR. IF APPLICABLE SPARES HAVE BEEN SOLD, SEND THIS DOCUMENT TO THE
NEW OWNER. THIS IS AN ENHANCED REQUIRED FOR COMPLIANCE DOCUMENT. THE BOEING
PROCESSES USED TO CREATE THE SERVICE BULLETIN (SB) AND THE REQUIREMENTS BULLETIN
(RB) ENSURE THAT THE INFORMATION BETWEEN "RC START" AND "RC END" IN THE SB ARE IDENTICAL
TO THE INFORMATION IN THE SAME SECTIONS (COMPLIANCE, WORK INSTRUCTIONS…) OF THE RB
WHICH THE SB REFERS TO AS THE RELATED DOCUMENT.
1. Effectivity
A. Airplanes
This bulletin is applicable to 767-200, 767-300, 767-300F, 767-400ER Airplane(s), line number(s)
1-717, 719-922, 924-1064, 1068, 1070-1090, 1093-1097, 1099, 1101, 1103, 1105-1106, 1108,
1110, 1112, 1115, 1118, 1121, 1123, 1125, 1127, 1130, 1133, 1136, 1138, 1140-1142, 1144,
1146, 1148, 1150, 1152-1153, 1155, 1157, 1159, 1161, 1163, 1165, 1167, 1169, 1171, 1173,
1175, 1177, 1179-1180, 1182-1183, 1185-1187, 1189-1191, 1193-1195, 1197-1199, 1201,
1203-1204, 1206, 1208-1209, 1211-1212, 1214-1215, 1217-1218, 1220-1222, 1224-1225,
1227-1229, 1231-1233, 1235, 1237, 1239-1240, 1242, 1244-1245, 1247, 1249, 1251, 1253,
1255-1256, 1258, 1260, 1262-1263, 1265-1266, 1268, 1270, 1272, 1274, 1276, 1278-1279, 1281,
1283, 1285, 1287, 1289, 1291-1292, 1294, 1296, 1298, 1300, 1302, 1304-1305, 1307, 1309, 1311,
1313, 1315, 1317-1318, 1320, 1322-1323, 1325, 1327, 1329-1330, 1332, 1334, 1336, 1338, 1340,
1342-1343, 1345, 1347, 1349, 1351, 1353, 1355-1356, 1364, 1366, 1368-1369, 1371, 1373-1375,
1377, 1379, 1381-9999 in 7 Group(s). Where the effectivity is presented with hyphens between
line numbers, the airplane applicability means "through" and "inclusive", e.g. line numbers 1-9
means line numbers 1 through 9 inclusive.
The Variable Numbers and Group Information for the applicable airplanes is given below.
NOTE: The Variable Number table below includes affected airplanes available as of the issue
date of this bulletin. Affected airplane Variable Numbers added to MyBoeingFleet.com
after the issue date of this bulletin will be shown using the Maintenance Performance
Toolbox EFFECTIVITY search function result.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 10, 2024
767-57A0148 RB
5 of 416

### Page 6

DESCRIPTIONCONFIGURATIONGROUP
767-200/-300/-300F airplanes with production seal retainer up to line
number 1063.
-1
Airplanes that have not replaced underwing longeron fittings.1
Airplanes that have replaced the left side and not the right side
underwing longeron fitting.
2
Airplanes that have replaced the right side and not the left side
underwing longeron fitting.
3
Airplanes that have replaced both the left side and right side
underwing longeron fittings.
4
767-400ER airplanes up to line number 1063.-2
Airplanes that have not replaced underwing longeron fittings.1
Airplanes that have replaced the left side and not the right side
underwing longeron fitting.
2
Airplanes that have replaced the right side and not the left side
underwing longeron fitting.
3
Airplanes that have replaced both the left side and right side
underwing longeron fittings.
4
767-200 airplanes without production seal retainer up to line number
1063.
-3
Airplanes that have not replaced underwing longeron fittings.1
Airplanes that have replaced the left side and not the right side
underwing longeron fitting.
2
Airplanes that have replaced the right side and not the left side
underwing longeron fitting.
3
Airplanes that have replaced both the left side and right side
underwing longeron fittings.
4
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 10, 2024
767-57A0148 RB
6 of 416
REQUIREMENTS BULLETIN 767-57A0148
ALERTALERT

### Page 7

DESCRIPTIONCONFIGURATIONGROUP
767-200 airplanes which are subject to post-production seal retainer
incorporated by Service Bulletin 767-57-0026.
-4
Airplanes that have incorporated Service Bulletin 767-57-0026 and
have not replaced underwing longeron fittings.
1
Airplanes that have not incorporated Service Bulletin 767-57-0026
and have not replaced underwing longeron fittings.
2
Airplanes that have incorporated Service Bulletin 767-57-0026 and
have replaced the left side and not right side underwing longeron
fitting.
3
Airplanes that have not incorporated Service Bulletin 767-57-0026
and have replaced the left side and not right side underwing longeron
fitting.
4
Airplanes that have incorporated Service Bulletin 767-57-0026 and
have replaced the right side and not left side underwing longeron
fitting.
5
Airplanes that have not incorporated Service Bulletin 767-57-0026
and have replaced the right side and not left side underwing longeron
fitting.
6
Airplanes that have incorporated Service Bulletin 767-57-0026 and
have replaced both the left side and right side underwing longeron
fittings.
7
Airplanes that have not incorporated Service Bulletin 767-57-0026
and have replaced both the left side and right side underwing longeron
fittings.
8
767-200/-300/-300F airplanes line numbers 1064, 1068, 1070 and
onwards. These airplanes have improved design underwing longeron
fittings fillet radius details installed in production.
-5
Airplanes that have not replaced underwing longeron fittings.1
Airplanes that have replaced the left side and not the right side
underwing longeron fitting.
2
Airplanes that have replaced the right side and not the left side
underwing longeron fitting.
3
Airplanes that have replaced both the left side and right side
underwing longeron fittings.
4
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 10, 2024
767-57A0148 RB
7 of 416
REQUIREMENTS BULLETIN 767-57A0148
ALERTALERT

### Page 8

DESCRIPTIONCONFIGURATIONGROUP
767-200/-300 airplanes, without production seal retainer and that
have the internal bathtub fitting tension bolt head located on the
forward side of the joint.
-6
Airplanes that have not replaced underwing longeron fittings.1
Airplanes that have replaced the left side and not the right side
underwing longeron fitting.
2
Airplanes that have replaced the right side and not the left side
underwing longeron fitting.
3
Airplanes that have replaced both the left side and right side
underwing longeron fittings.
4
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 10, 2024
767-57A0148 RB
8 of 416
REQUIREMENTS BULLETIN 767-57A0148
ALERTALERT

### Page 9

DESCRIPTIONCONFIGURATIONGROUP
767-300 airplanes which are subject to post-production seal retainer
incorporated by Service Bulletin 767-57-0026 and have the internal
bathtub fitting tension bolt head located on the forward side of the
joint.
-7
Airplanes that have incorporated Service Bulletin 767-57-0026 and
have not replaced underwing longeron fittings.
1
Airplanes that have not incorporated Service Bulletin 767-57-0026
and have not replaced underwing longeron fittings.
2
Airplanes that have incorporated Service Bulletin 767-57-0026 and
have replaced the left side and not right side underwing longeron
fitting.
3
Airplanes that have not incorporated Service Bulletin 767-57-0026
and have replaced the left side and not right side underwing longeron
fitting.
4
Airplanes that have incorporated Service Bulletin 767-57-0026 and
have replaced the right side and not left side underwing longeron
fitting.
5
Airplanes that have not incorporated Service Bulletin 767-57-0026
and have replaced the right side and not left side underwing longeron
fitting.
6
Airplanes that have incorporated Service Bulletin 767-57-0026 and
have replaced both the left side and right side underwing longeron
fittings.
7
Airplanes that have not incorporated Service Bulletin 767-57-0026
and have replaced both the left side and right side underwing longeron
fittings.
8
Airplane Models:
767-200, 767-300, 767-300F, 767-400ER
GroupVariable Number
6VA001 - VA020
6VA301 - VA315
6VA501 - VA530
6VA701 - VA719
GroupVariable Number
6VA801 - VA810
6VB001 - VB002
6VB051 - VB055
6VB101 - VB125
GroupVariable Number
6VB201 - VB202
6VB251 - VB253
6VB281 - VB284
6VB301 - VB302
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 10, 2024
767-57A0148 RB
9 of 416
REQUIREMENTS BULLETIN 767-57A0148
ALERTALERT

### Page 10

GroupVariable Number
6VB321 - VB328
3VB329 - VB332
6VB371 - VB373
6VB401
3VB441 - VB444
6VE001 - VE003
6VE021 - VE023
6VE041 - VE043
6VE061 - VE069
6VE083 - VE086
6VE101 - VE104
6VE116 - VE117
3VE118
6VE121 - VE126
6VE141 - VE146
3VE147 - VE152
3VE171 - VE172
4VF001 - VF002
4VF041
1VF042
1VF051
1VF061 - VF062
1VF071 - VF072
1VF091 - VF093
1VF101 - VF102
1VF161 - VF162
1VF171 - VF172
1VF180 - VF184
1VF251
6VK001 - VK008
1VK009 - VK016
6VK021 - VK022
6VK031 - VK045
GroupVariable Number
1VK046 - VK056
6VK081 - VK091
1VK092 - VK113
1VK131 - VK133
1VK141 - VK148
1VK161 - VK164
1VK171
1VK181
1VK186
7VL001 - VL003
1VL004 - VL006
7VL011
1VL701 - VL703
1VL751 - VL755
1VL806 - VL807
1VL871 - VL873
1VL891 - VL900
1VL911 - VL914
1VL931 - VL932
1VL941
7VN001 - VN015
1VN016 - VN041
7VN051 - VN058
1VN059 - VN064
7VN081 - VN084
1VN085 - VN099
1VN111 - VN127
1VN130 - VN137
7VN151
1VN152 - VN158
1VN163 - VN168
7VN171 - VN172
1VN173 - VN174
GroupVariable Number
1VN191 - VN198
1VN211 - VN212
1VN221 - VN225
1VN231 - VN234
1VN241 - VN243
1VN251 - VN276
1VN291 - VN293
1VN301 - VN314
1VN371 - VN372
1VN376
1VN381 - VN388
1VN421 - VN427
1VN436
1VN471 - VN472
1VN491 - VN513
1VN531 - VN532
1VN536 - VN537
1VN541 - VN542
1VN546 - VN547
1VN551
1VN556 - VN557
1VN561 - VN562
1VN631 - VN638
1VN651 - VN658
1VN671 - VN672
1VN676
1VN681 - VN691
1VN731 - VN732
1VN751 - VN753
1VN791 - VN792
1VN811 - VN813
1VN921 - VN922
1VN931 - VN936
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 10, 2024
767-57A0148 RB
10 of 416
REQUIREMENTS BULLETIN 767-57A0148
ALERTALERT

### Page 11

GroupVariable Number
1VN951 - VN953
1VN966 - VN972
2VQ001 - VQ021
2VQ071 - VQ086
2VQ111
1VR051 - VR060
1VR081
1VR084
1VR086 - VR089
1VR106 - VR109
1VR201 - VR211
1VR251
1VR256 - VR260
1VR266 - VR292
5VR293 - VR318
5VR321 - VR326
1VR401
1VR421 - VR423
1VR426
1VR441
1VR461
1VR471 - VR472
1VS051 - VS056
1VS061
1VS066 - VS070
1VS073 - VS078
1VS091 - VS104
1VS111 - VS113
1VS131 - VS133
1VS136 - VS137
1VS176 - VS177
GroupVariable Number
1VS186 - VS187
1VS196 - VS203
1VS206 - VS208
1VS211
1VS216 - VS217
1VS231
1VS246 - VS248
1VS261 - VS263
1VS266 - VS274
1VS291 - VS293
1VS301 - VS303
1VS306 - VS311
1VS316
1VS321 - VS324
1VS331 - VS333
1VS336 - VS337
1VS366 - VS367
1VS381 - VS382
1VS391 - VS392
1VS401
1VS426 - VS428
1VS466 - VS472
1VS486
1VS496 - VS497
1VS506 - VS507
1VS526
1VS546 - VS549
1VS701 - VS736
1VS751 - VS759
1VS821 - VS825
1VS841 - VS844
GroupVariable Number
1VS861
1VS881 - VS883
1VS891
1VS896
1VS901 - VS912
1VS916
1VS921 - VS928
1VS931 - VS933
1VS941
1VS951 - VS954
1VS961 - VS969
1VS971 - VS977
1VS981 - VS984
1VT001 - VT013
1VT021
1VT031 - VT032
5VT033
1VT501
1VT511 - VT513
1VT521 - VT523
1VT531 - VT533
1VT541 - VT546
1VT551 - VT552
1VT556 - VT558
5VT559 - VT699
5VT701 - VT705
5VT731 - VT735
5VT737
1VW701 - VW721
1VW851
--
B. Spares Affected
None.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 10, 2024
767-57A0148 RB
11 of 416
REQUIREMENTS BULLETIN 767-57A0148
ALERTALERT

### Page 12

2. CONCURRENT REQUIREMENTS
None.
3. COMPLIANCE
The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to
Requirements Bulletin 767-57A0148 RB. The Airworthiness Directive will make the compliance tasks and
times given in Requirements Bulletin 767-57A0148 RB mandatory.
Accomplish the required action(s), based on the applicable condition(s) in Table(s) 1 through 4, in accordance
with Accomplishment Instructions.
When more than one OPTION is given for a CONDITION, do only one of the OPTION numbers. When
more than one ACTION is given for a CONDITION or an OPTION, do all of the ACTION numbers for that
CONDITION or OPTION.
Group 1, Configuration 1, 3; Group 2, Configuration 1, 3; Group 3, Configuration 1, 3; Group 4, Configu-
ration 1-2, 5-6; Group 5, Configuration 1, 3; Group 6, Configuration 1, 3; Group 7, Configuration 1-2, 5-
6:
Table 1: Left Side Underwing Longeron Fitting Forward Lower Fastener Holes Inspection
Repeat Interval
(Not to Exceed)
Boeing Recommended
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Within 6,000
flight-cycles or
14,000 flight-
hours after the
Original Issue
date of Require-
ments Bulletin
767-57A0148
RB, whichever
occurs first.
Before 22,000
total flight-cycles
or 80,000 total
flight-hours,
whichever oc-
curs first.
Do an open hole High Fre-
quency Eddy Current
(HFEC) inspection of the
fastener holes common to
the underwing longeron fit-
ting, upper drag splice an-
gle, and lower drag splice
angle for any crack.
All Airplanes.
-Before further flight.CONDITION 1 (ACTION 1):
Install fasteners.
CONDITION 1: NO CRACK
FOUND.
12,000 flight-cy-
cles or 28,000
flight-hours,
whichever oc-
curs first.
-CONDITION 1 (ACTION 2):
Repeat the open hole
HFEC inspection of the
fastener holes common to
the underwing longeron fit-
ting, upper drag splice an-
gle, and lower drag splice
angle for any crack.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 10, 2024
767-57A0148 RB
12 of 416
REQUIREMENTS BULLETIN 767-57A0148
ALERTALERT

### Page 13

Group 1, Configuration 1, 3; Group 2, Configuration 1, 3; Group 3, Configuration 1, 3; Group 4, Configu-
ration 1-2, 5-6; Group 5, Configuration 1, 3; Group 6, Configuration 1, 3; Group 7, Configuration 1-2, 5-
6:
Table 1: Left Side Underwing Longeron Fitting Forward Lower Fastener Holes Inspection
Repeat Interval
(Not to Exceed)
Boeing Recommended
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flight.CONDITION 2 (ACTION 1):
Do hole oversize repair at
the affected hole loca-
tion(s), through all fittings
and angles in the joint. (a)
CONDITION 2: ANY
CRACK FOUND ON THE
UNDERWING LONGERON
FITTING AND NO CRACK
FOUND ON THE UPPER
DRAG SPLICE ANGLE OR
THE LOWER DRAG
SPLICE ANGLE.
-Before further flight.CONDITION 2 (ACTION 2):
At oversize hole repair loca-
tion(s), do an open hole
HFEC inspection of the fit-
ting and angles for any
crack. (b)
-Before further flight.CONDITION 2.1 (ACTION
1): Install fasteners.
CONDITION 2.1: NO
CRACK FOUND AS A RE-
SULT OF CONDITION 2
(ACTION 2) INSPECTION. 12,000 flight-cy-cles or 28,000
flight-hours,
whichever oc-
curs first.
-CONDITION 2.1 (ACTION
2): Repeat the open hole
HFEC inspection of the
fastener holes common to
the underwing longeron fit-
ting, upper drag splice an-
gle, and lower drag splice
angle for any crack.
-Before further flight.Do an open hole HFEC in-
spection of the entire fasten-
er stack-up common to the
tension bolt hole and a sur-
face HFEC inspection of
the front spar lower chord
for any crack.
CONDITION 2.2: ANY
CRACK FOUND THAT IS
MORE THAN THE SEC-
OND HOLE OVERSIZE
FROM NOMINAL AS A
RESULT OF CONDITION
2 (ACTION 2) INSPEC-
TION.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 10, 2024
767-57A0148 RB
13 of 416
REQUIREMENTS BULLETIN 767-57A0148
ALERTALERT

### Page 14

Group 1, Configuration 1, 3; Group 2, Configuration 1, 3; Group 3, Configuration 1, 3; Group 4, Configu-
ration 1-2, 5-6; Group 5, Configuration 1, 3; Group 6, Configuration 1, 3; Group 7, Configuration 1-2, 5-
6:
Table 1: Left Side Underwing Longeron Fitting Forward Lower Fastener Holes Inspection
Repeat Interval
(Not to Exceed)
Boeing Recommended
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flight.CONDITION 2.2.1 (OP-
TION 1) (ACTION 1): Re-
place the underwing
longeron fitting with new
underwing longeron fitting.
CONDITION 2.2.1: NO
CRACK FOUND AS A RE-
SULT OF CONDITION 2.2
INSPECTION.
22,000 flight-cy-
cles or 80,000
flight-hours,
whichever oc-
curs first.
-CONDITION 2.2.1 (OP-
TION 1) (ACTION 2): Re-
peat the open hole HFEC
inspection of the fastener
holes common to the under-
wing longeron fitting, upper
drag splice angle, and low-
er drag splice angle for any
crack.
-Before further flight.CONDITION 2.2.1 (OP-
TION 2): Contact The Boe-
ing Company for any possi-
ble underwing longeron fit-
ting hole repair instructions
and do the repair.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 10, 2024
767-57A0148 RB
14 of 416
REQUIREMENTS BULLETIN 767-57A0148
ALERTALERT

### Page 15

Group 1, Configuration 1, 3; Group 2, Configuration 1, 3; Group 3, Configuration 1, 3; Group 4, Configu-
ration 1-2, 5-6; Group 5, Configuration 1, 3; Group 6, Configuration 1, 3; Group 7, Configuration 1-2, 5-
6:
Table 1: Left Side Underwing Longeron Fitting Forward Lower Fastener Holes Inspection
Repeat Interval
(Not to Exceed)
Boeing Recommended
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flight.CONDITION 2.2.2 (OP-
TION 1) (ACTION 1): Con-
tact The Boeing Company
for any tension bolt fasten-
er stack-up repair and any
front spar lower chord re-
pair instructions and do the
repair.
CONDITION 2.2.2: ANY
CRACK FOUND AS A RE-
SULT OF CONDITION 2.2
INSPECTION.
-Before further flight.CONDITION 2.2.2 (OP-
TION 1) (ACTION 2): Re-
place the underwing
longeron fitting with new
underwing longeron fitting.
22,000 flight-cy-
cles or 80,000
flight-hours,
whichever oc-
curs first.
-CONDITION 2.2.2 (OP-
TION 1) (ACTION 3): Re-
peat the open hole HFEC
inspection of the fastener
holes common to the under-
wing longeron fitting, upper
drag splice angle, and low-
er drag splice angle for any
crack.
-Before further flight.CONDITION 2.2.2 (OP-
TION 2): Contact The Boe-
ing Company for any ten-
sion bolt fastener stack-up
repair, any front spar lower
chord repair, and any possi-
ble underwing longeron fit-
ting hole repair instructions
and do the repair.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 10, 2024
767-57A0148 RB
15 of 416
REQUIREMENTS BULLETIN 767-57A0148
ALERTALERT

### Page 16

Group 1, Configuration 1, 3; Group 2, Configuration 1, 3; Group 3, Configuration 1, 3; Group 4, Configu-
ration 1-2, 5-6; Group 5, Configuration 1, 3; Group 6, Configuration 1, 3; Group 7, Configuration 1-2, 5-
6:
Table 1: Left Side Underwing Longeron Fitting Forward Lower Fastener Holes Inspection
Repeat Interval
(Not to Exceed)
Boeing Recommended
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flight.CONDITION 3 (ACTION 1):
Do hole oversize repair at
the affected hole loca-
tion(s), through all fittings
and angles in the joint. (a)
CONDITION 3: ANY
CRACK FOUND ON THE
UPPER DRAG SPLICE
ANGLE OR THE LOWER
DRAG SPLICE ANGLE
AND NO CRACK FOUND
ON THE UNDERWING
LONGERON FITTING.
-Before further flight.CONDITION 3 (ACTION 2):
At oversize hole repair loca-
tion(s), do an open hole
HFEC inspection of the fit-
ting and angles for any
crack. (b)
-Before further flight.CONDITION 3.1 (ACTION
1): Install fasteners.
CONDITION 3.1: NO
CRACK FOUND AS A RE-
SULT OF CONDITION 3
(ACTION 2) INSPECTION. 12,000 flight-cy-cles or 28,000
flight-hours,
whichever oc-
curs first.
-CONDITION 3.1 (ACTION
2): Repeat the open hole
HFEC inspection of the
fastener holes common to
the underwing longeron fit-
ting, upper drag splice an-
gle, and lower drag splice
angle for any crack.
-Before further flight.Do an open hole HFEC in-
spection of the entire fasten-
er stack-up common to the
tension bolt hole and a sur-
face HFEC inspection of
the front spar lower chord
for any crack.
CONDITION 3.2: ANY
CRACK FOUND THAT IS
MORE THAN THE SEC-
OND HOLE OVERSIZE
FROM NOMINAL AS A
RESULT OF CONDITION
3 (ACTION 2) INSPEC-
TION.
-Before further flight.Contact The Boeing Com-
pany for any upper drag
splice angle repair and any
lower drag splice angle re-
pair instructions and do the
repair.
CONDITION 3.2.1: NO
CRACK FOUND AS A RE-
SULT OF CONDITION 3.2
INSPECTION.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 10, 2024
767-57A0148 RB
16 of 416
REQUIREMENTS BULLETIN 767-57A0148
ALERTALERT

### Page 17

Group 1, Configuration 1, 3; Group 2, Configuration 1, 3; Group 3, Configuration 1, 3; Group 4, Configu-
ration 1-2, 5-6; Group 5, Configuration 1, 3; Group 6, Configuration 1, 3; Group 7, Configuration 1-2, 5-
6:
Table 1: Left Side Underwing Longeron Fitting Forward Lower Fastener Holes Inspection
Repeat Interval
(Not to Exceed)
Boeing Recommended
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flight.Contact The Boeing Com-
pany for any upper drag
splice angle repair, any
lower drag splice angle re-
pair, any tension bolt fasten-
er stack-up repair, and any
front spar lower chord re-
pair instructions and do the
repair.
CONDITION 3.2.2: ANY
CRACK FOUND AS A RE-
SULT OF CONDITION 3.2
INSPECTION.
-Before further flight.CONDITION 4 (ACTION 1):
Do hole oversize repair at
the affected hole loca-
tion(s), through all fittings
and angles in the joint. (a)
CONDITION 4: ANY
CRACK FOUND ON THE
UNDERWING LONGERON
FITTING AND ANY
CRACK FOUND ON EI-
THER THE UPPER DRAG
SPLICE ANGLE OR THE
LOWER DRAG SPLICE
ANGLE.
-Before further flight.CONDITION 4 (ACTION 2):
At oversize hole repair loca-
tion(s), do an open hole
HFEC inspection of the fit-
ting and angles for any
crack. (b)
-Before further flight.CONDITION 4.1 (ACTION
1): Install fasteners.
CONDITION 4.1: NO
CRACK FOUND AS A RE-
SULT OF CONDITION 4
(ACTION 2) INSPECTION. 12,000 flight-cy-cles or 28,000
flight-hours,
whichever oc-
curs first.
-CONDITION 4.1 (ACTION
2): Repeat the open hole
HFEC inspection of the
fastener holes common to
the underwing longeron fit-
ting, upper drag splice an-
gle, and lower drag splice
angle for any crack.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 10, 2024
767-57A0148 RB
17 of 416
REQUIREMENTS BULLETIN 767-57A0148
ALERTALERT

### Page 18

Group 1, Configuration 1, 3; Group 2, Configuration 1, 3; Group 3, Configuration 1, 3; Group 4, Configu-
ration 1-2, 5-6; Group 5, Configuration 1, 3; Group 6, Configuration 1, 3; Group 7, Configuration 1-2, 5-
6:
Table 1: Left Side Underwing Longeron Fitting Forward Lower Fastener Holes Inspection
Repeat Interval
(Not to Exceed)
Boeing Recommended
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flight.Do an open hole HFEC in-
spection of the entire fasten-
er stack-up common to the
tension bolt hole and a sur-
face HFEC inspection of
the front spar lower chord
for any crack.
CONDITION 4.2: ANY
CRACK FOUND THAT IS
MORE THAN THE SEC-
OND HOLE OVERSIZE
FROM NOMINAL AT A
FASTENER HOLE ON
THE UNDERWING
LONGERON FITTING AND
NO CRACK FOUND ON
THE UPPER DRAG
SPLICE ANGLE OR THE
LOWER DRAG SPLICE
ANGLE, AS A RESULT OF
CONDITION 4 (ACTION 2)
INSPECTION.
-Before further flight.CONDITION 4.2.1 (OP-
TION 1) (ACTION 1): Re-
place the underwing
longeron fitting with new
underwing longeron fitting.
CONDITION 4.2.1: NO
CRACK FOUND AS A RE-
SULT OF CONDITION 4.2
INSPECTION.
22,000 flight-cy-
cles or 80,000
flight-hours,
whichever oc-
curs first.
-CONDITION 4.2.1 (OP-
TION 1) (ACTION 2): Re-
peat the open hole HFEC
inspection of the fastener
holes common to the under-
wing longeron fitting, upper
drag splice angle, and low-
er drag splice angle for any
crack.
-Before further flight.CONDITION 4.2.1 (OP-
TION 2): Contact The Boe-
ing Company for any possi-
ble underwing longeron fit-
ting hole repair instructions
and do the repair.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 10, 2024
767-57A0148 RB
18 of 416
REQUIREMENTS BULLETIN 767-57A0148
ALERTALERT

### Page 19

Group 1, Configuration 1, 3; Group 2, Configuration 1, 3; Group 3, Configuration 1, 3; Group 4, Configu-
ration 1-2, 5-6; Group 5, Configuration 1, 3; Group 6, Configuration 1, 3; Group 7, Configuration 1-2, 5-
6:
Table 1: Left Side Underwing Longeron Fitting Forward Lower Fastener Holes Inspection
Repeat Interval
(Not to Exceed)
Boeing Recommended
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flight.CONDITION 4.2.2 (OP-
TION 1) (ACTION 1): Con-
tact The Boeing Company
for any tension bolt fasten-
er stack-up repair and any
front spar lower chord re-
pair instructions and do the
repair.
CONDITION 4.2.2: ANY
CRACK FOUND AS A RE-
SULT OF CONDITION 4.2
INSPECTION.
-Before further flight.CONDITION 4.2.2 (OP-
TION 1) (ACTION 2): Re-
place the underwing
longeron fitting with new
underwing longeron fitting.
22,000 flight-cy-
cles or 80,000
flight-hours,
whichever oc-
curs first.
-CONDITION 4.2.2 (OP-
TION 1) (ACTION 3): Re-
peat the open hole HFEC
inspection of the fastener
holes common to the under-
wing longeron fitting, upper
drag splice angle, and low-
er drag splice angle for any
crack.
-Before further flight.CONDITION 4.2.2 (OP-
TION 2): Contact The Boe-
ing Company for any ten-
sion bolt fastener stack-up
repair, any front spar lower
chord repair, and any possi-
ble underwing longeron fit-
ting hole repair instructions
and do the repair.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 10, 2024
767-57A0148 RB
19 of 416
REQUIREMENTS BULLETIN 767-57A0148
ALERTALERT

### Page 20

Group 1, Configuration 1, 3; Group 2, Configuration 1, 3; Group 3, Configuration 1, 3; Group 4, Configu-
ration 1-2, 5-6; Group 5, Configuration 1, 3; Group 6, Configuration 1, 3; Group 7, Configuration 1-2, 5-
6:
Table 1: Left Side Underwing Longeron Fitting Forward Lower Fastener Holes Inspection
Repeat Interval
(Not to Exceed)
Boeing Recommended
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flight.Do an open hole HFEC in-
spection of the entire fasten-
er stack-up common to the
tension bolt hole and a sur-
face HFEC inspection of
the front spar lower chord
for any crack.
CONDITION 4.3: ANY
CRACK FOUND THAT IS
MORE THAN THE SEC-
OND HOLE OVERSIZE
FROM NOMINAL AT A
FASTENER HOLE ON
THE UPPER DRAG
SPLICE ANGLE OR THE
LOWER DRAG SPLICE
ANGLE BUT NO CRACK
FOUND ON THE UNDER-
WING LONGERON FIT-
TING, AS A RESULT OF
CONDITION 4 (ACTION 2)
INSPECTION.
-Before further flight.Contact The Boeing Com-
pany for any upper drag
splice angle repair and any
lower drag splice angle re-
pair instructions and do the
repair.
CONDITION 4.3.1: NO
CRACK FOUND AS A RE-
SULT OF CONDITION 4.3
INSPECTION.
-Before further flight.Contact The Boeing Com-
pany for any upper drag
splice angle repair, any
lower drag splice angle re-
pair, any tension bolt fasten-
er stack-up repair, and any
front spar lower chord re-
pair instructions and do the
repair.
CONDITION 4.3.2: ANY
CRACK FOUND AS A RE-
SULT OF CONDITION 4.3
INSPECTION.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 10, 2024
767-57A0148 RB
20 of 416
REQUIREMENTS BULLETIN 767-57A0148
ALERTALERT

### Page 21

Group 1, Configuration 1, 3; Group 2, Configuration 1, 3; Group 3, Configuration 1, 3; Group 4, Configu-
ration 1-2, 5-6; Group 5, Configuration 1, 3; Group 6, Configuration 1, 3; Group 7, Configuration 1-2, 5-
6:
Table 1: Left Side Underwing Longeron Fitting Forward Lower Fastener Holes Inspection
Repeat Interval
(Not to Exceed)
Boeing Recommended
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flight.Do an open hole HFEC in-
spection of the entire fasten-
er stack-up common to the
tension bolt hole and a sur-
face HFEC inspection of
the front spar lower chord
for any crack.
CONDITION 4.4: ANY
CRACK FOUND THAT IS
MORE THAN THE SEC-
OND HOLE OVERSIZE
FROM NOMINAL AT A
FASTENER HOLE ON
THE UNDERWING
LONGERON FITTING,
AND EITHER THE UPPER
DRAG SPLICE ANGLE OR
THE LOWER DRAG
SPLICE ANGLE AS A RE-
SULT OF CONDITION 4
(ACTION 2) INSPECTION.
-Before further flight.Contact The Boeing Com-
pany for any upper drag
splice angle repair, any
lower drag splice angle re-
pair, and any possible un-
derwing longeron fitting
hole repair instructions and
do the repair.
CONDITION 4.4.1: NO
CRACK FOUND AS A RE-
SULT OF CONDITION 4.4
INSPECTION.
-Before further flight.Contact The Boeing Com-
pany for any upper drag
splice angle repair, any
lower drag splice angle re-
pair, any tension bolt fasten-
er stack-up repair, any front
spar lower chord repair,
and any possible under-
wing longeron fitting hole
repair instructions and do
the repair.
CONDITION 4.4.2: ANY
CRACK FOUND AS A RE-
SULT OF CONDITION 4.4
INSPECTION.
(a) Do the oversize hole repair by reaming in 1/64 inch increments to a maximum diameter of 0.6567 (maximum
diameter for 2nd oversize of nominal production fastener).
(b) Do the open hole HFEC inspection after each incremental oversize reaming operation to confirm a crack-
free condition.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 10, 2024
767-57A0148 RB
21 of 416
REQUIREMENTS BULLETIN 767-57A0148
ALERTALERT

### Page 22

Group 1, Configuration 1-2; Group 2, Configuration 1-2; Group 3, Configuration 1-2; Group 4, Configuration
1-4; Group 5, Configuration 1-2; Group 6, Configuration 1-2; Group 7, Configuration 1-4:
Table 2: Right Side Underwing Longeron Fitting Forward Lower Fastener Holes Inspection
Repeat Interval
(Not to Exceed)
Boeing Recommended
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Within 6,000
flight-cycles or
14,000 flight-
hours after the
Original Issue
date of Require-
ments Bulletin
767-57A0148
RB, whichever
occurs first.
Before 22,000
total flight-cycles
or 80,000 total
flight-hours,
whichever oc-
curs first.
Do an open hole High Fre-
quency Eddy Current
(HFEC) inspection of the
fastener holes common to
the underwing longeron fit-
ting, upper drag splice an-
gle, and lower drag splice
angle for any crack.
All Airplanes.
-Before further flight.CONDITION 5 (ACTION 1):
Install fasteners.
CONDITION 5: NO CRACK
FOUND.
12,000 flight-cy-
cles or 28,000
flight-hours,
whichever oc-
curs first.
-CONDITION 5 (ACTION 2):
Repeat the open hole
HFEC inspection of the
fastener holes common to
the underwing longeron fit-
ting, upper drag splice an-
gle, and lower drag splice
angle for any crack.
-Before further flight.CONDITION 6 (ACTION 1):
Do hole oversize repair at
the affected hole loca-
tion(s), through all fittings
and angles in the joint. (a)
CONDITION 6: ANY
CRACK FOUND ON THE
UNDERWING LONGERON
FITTING AND NO CRACK
FOUND ON THE UPPER
DRAG SPLICE ANGLE OR
THE LOWER DRAG
SPLICE ANGLE.
-Before further flight.CONDITION 6 (ACTION 2):
At oversize hole repair loca-
tion(s), do an open hole
HFEC inspection of the fit-
ting and angles for any
crack. (b)
-Before further flight.CONDITION 6.1 (ACTION
1): Install fasteners.
CONDITION 6.1: NO
CRACK FOUND AS A RE-
SULT OF CONDITION 6
(ACTION 2) INSPECTION. 12,000 flight-cy-cles or 28,000
flight-hours,
whichever oc-
curs first.
-CONDITION 6.1 (ACTION
2): Repeat the open hole
HFEC inspection of the
fastener holes common to
the underwing longeron fit-
ting, upper drag splice an-
gle, and lower drag splice
angle for any crack.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 10, 2024
767-57A0148 RB
22 of 416
REQUIREMENTS BULLETIN 767-57A0148
ALERTALERT

### Page 23

Group 1, Configuration 1-2; Group 2, Configuration 1-2; Group 3, Configuration 1-2; Group 4, Configuration
1-4; Group 5, Configuration 1-2; Group 6, Configuration 1-2; Group 7, Configuration 1-4:
Table 2: Right Side Underwing Longeron Fitting Forward Lower Fastener Holes Inspection
Repeat Interval
(Not to Exceed)
Boeing Recommended
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flight.Do an open hole HFEC in-
spection of the entire fasten-
er stack-up common to the
tension bolt hole and a sur-
face HFEC inspection of
the front spar lower chord
for any crack.
CONDITION 6.2: ANY
CRACK FOUND THAT IS
MORE THAN THE SEC-
OND HOLE OVERSIZE
FROM NOMINAL AS A
RESULT OF CONDITION
6 (ACTION 2) INSPEC-
TION.
-Before further flight.CONDITION 6.2.1 (OP-
TION 1) (ACTION 1): Re-
place the underwing
longeron fitting with new
underwing longeron fitting.
CONDITION 6.2.1: NO
CRACK FOUND AS A RE-
SULT OF CONDITION 6.2
INSPECTION.
22,000 flight-cy-
cles or 80,000
flight-hours,
whichever oc-
curs first.
-CONDITION 6.2.1 (OP-
TION 1) (ACTION 2): Re-
peat the open hole HFEC
inspection of the fastener
holes common to the under-
wing longeron fitting, upper
drag splice angle, and low-
er drag splice angle for any
crack.
-Before further flight.CONDITION 6.2.1 (OP-
TION 2): Contact The Boe-
ing Company for any possi-
ble underwing longeron fit-
ting hole repair instructions
and do the repair.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 10, 2024
767-57A0148 RB
23 of 416
REQUIREMENTS BULLETIN 767-57A0148
ALERTALERT

### Page 24

Group 1, Configuration 1-2; Group 2, Configuration 1-2; Group 3, Configuration 1-2; Group 4, Configuration
1-4; Group 5, Configuration 1-2; Group 6, Configuration 1-2; Group 7, Configuration 1-4:
Table 2: Right Side Underwing Longeron Fitting Forward Lower Fastener Holes Inspection
Repeat Interval
(Not to Exceed)
Boeing Recommended
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flight.CONDITION 6.2.2 (OP-
TION 1) (ACTION 1): Con-
tact The Boeing Company
for any tension bolt fasten-
er stack-up repair and any
front spar lower chord re-
pair instructions and do the
repair.
CONDITION 6.2.2: ANY
CRACK FOUND AS A RE-
SULT OF CONDITION 6.2
INSPECTION.
-Before further flight.CONDITION 6.2.2 (OP-
TION 1) (ACTION 2): Re-
place the underwing
longeron fitting with new
underwing longeron fitting.
22,000 flight-cy-
cles or 80,000
flight-hours,
whichever oc-
curs first.
-CONDITION 6.2.2 (OP-
TION 1) (ACTION 3): Re-
peat the open hole HFEC
inspection of the fastener
holes common to the under-
wing longeron fitting, upper
drag splice angle, and low-
er drag splice angle for any
crack.
-Before further flight.CONDITION 6.2.2 (OP-
TION 2): Contact The Boe-
ing Company for any ten-
sion bolt fastener stack-up
repair, any front spar lower
chord repair, and any possi-
ble underwing longeron fit-
ting hole repair instructions
and do the repair.
-Before further flight.CONDITION 7 (ACTION 1):
Do hole oversize repair at
the affected hole loca-
tion(s), through all fittings
and angles in the joint. (a)
CONDITION 7: ANY
CRACK FOUND ON THE
UPPER DRAG SPLICE
ANGLE OR THE LOWER
DRAG SPLICE ANGLE
AND NO CRACK FOUND
ON THE UNDERWING
LONGERON FITTING.
-Before further flight.CONDITION 7 (ACTION 2):
At oversize hole repair loca-
tion(s), do an open hole
HFEC inspection of the fit-
ting and angles for any
crack. (b)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 10, 2024
767-57A0148 RB
24 of 416
REQUIREMENTS BULLETIN 767-57A0148
ALERTALERT

### Page 25

Group 1, Configuration 1-2; Group 2, Configuration 1-2; Group 3, Configuration 1-2; Group 4, Configuration
1-4; Group 5, Configuration 1-2; Group 6, Configuration 1-2; Group 7, Configuration 1-4:
Table 2: Right Side Underwing Longeron Fitting Forward Lower Fastener Holes Inspection
Repeat Interval
(Not to Exceed)
Boeing Recommended
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flight.CONDITION 7.1 (ACTION
1): Install fasteners.
CONDITION 7.1: NO
CRACK FOUND AS A RE-
SULT OF CONDITION 7
(ACTION 2) INSPECTION. 12,000 flight-cy-cles or 28,000
flight-hours,
whichever oc-
curs first.
-CONDITION 7.1 (ACTION
2): Repeat the open hole
HFEC inspection of the
fastener holes common to
the underwing longeron fit-
ting, upper drag splice an-
gle, and lower drag splice
angle for any crack.
-Before further flight.Do an open hole HFEC in-
spection of the entire fasten-
er stack-up common to the
tension bolt hole and a sur-
face HFEC inspection of
the front spar lower chord
for any crack.
CONDITION 7.2: ANY
CRACK FOUND THAT IS
MORE THAN THE SEC-
OND HOLE OVERSIZE
FROM NOMINAL AS A
RESULT OF CONDITION
7 (ACTION 2) INSPEC-
TION.
-Before further flight.Contact The Boeing Com-
pany for any upper drag
splice angle repair and any
lower drag splice angle re-
pair instructions and do the
repair.
CONDITION 7.2.1: NO
CRACK FOUND AS A RE-
SULT OF CONDITION 7.2
INSPECTION.
-Before further flight.Contact The Boeing Com-
pany for any upper drag
splice angle repair, any
lower drag splice angle re-
pair, any tension bolt fasten-
er stack-up repair, and any
front spar lower chord re-
pair instructions and do the
repair.
CONDITION 7.2.2: ANY
CRACK FOUND AS A RE-
SULT OF CONDITION 7.2
INSPECTION.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 10, 2024
767-57A0148 RB
25 of 416
REQUIREMENTS BULLETIN 767-57A0148
ALERTALERT

### Page 26

Group 1, Configuration 1-2; Group 2, Configuration 1-2; Group 3, Configuration 1-2; Group 4, Configuration
1-4; Group 5, Configuration 1-2; Group 6, Configuration 1-2; Group 7, Configuration 1-4:
Table 2: Right Side Underwing Longeron Fitting Forward Lower Fastener Holes Inspection
Repeat Interval
(Not to Exceed)
Boeing Recommended
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flight.CONDITION 8 (ACTION 1):
Do hole oversize repair at
the affected hole loca-
tion(s), through all fittings
and angles in the joint. (a)
CONDITION 8: ANY
CRACK FOUND ON THE
UNDERWING LONGERON
FITTING AND ANY
CRACK FOUND ON EI-
THER THE UPPER DRAG
SPLICE ANGLE OR THE
LOWER DRAG SPLICE
ANGLE.
-Before further flight.CONDITION 8 (ACTION 2):
At oversize hole repair loca-
tion(s), do an open hole
HFEC inspection of the fit-
ting and angles for any
crack. (b)
-Before further flight.CONDITION 8.1 (ACTION
1): Install fasteners.
CONDITION 8.1: NO
CRACK FOUND AS A RE-
SULT OF CONDITION 8
(ACTION 2) INSPECTION. 12,000 flight-cy-cles or 28,000
flight-hours,
whichever oc-
curs first.
-CONDITION 8.1 (ACTION
2): Repeat the open hole
HFEC inspection of the
fastener holes common to
the underwing longeron fit-
ting, upper drag splice an-
gle, and lower drag splice
angle for any crack.
-Before further flight.Do an open hole HFEC in-
spection of the entire fasten-
er stack-up common to the
tension bolt hole and a sur-
face HFEC inspection of
the front spar lower chord
for any crack.
CONDITION 8.2: ANY
CRACK FOUND THAT IS
MORE THAN THE SEC-
OND HOLE OVERSIZE
FROM NOMINAL AT A
FASTENER HOLE ON
THE UNDERWING
LONGERON FITTING ON-
LY, AS A RESULT OF
CONDITION 8 (ACTION 2)
INSPECTION.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 10, 2024
767-57A0148 RB
26 of 416
REQUIREMENTS BULLETIN 767-57A0148
ALERTALERT

### Page 27

Group 1, Configuration 1-2; Group 2, Configuration 1-2; Group 3, Configuration 1-2; Group 4, Configuration
1-4; Group 5, Configuration 1-2; Group 6, Configuration 1-2; Group 7, Configuration 1-4:
Table 2: Right Side Underwing Longeron Fitting Forward Lower Fastener Holes Inspection
Repeat Interval
(Not to Exceed)
Boeing Recommended
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flight.CONDITION 8.2.1 (OP-
TION 1) (ACTION 1): Re-
place the underwing
longeron fitting with new
underwing longeron fitting.
CONDITION 8.2.1: NO
CRACK FOUND AS A RE-
SULT OF CONDITION 8.2
INSPECTION.
22,000 flight-cy-
cles or 80,000
flight-hours,
whichever oc-
curs first.
-CONDITION 8.2.1 (OP-
TION 1) (ACTION 2): Re-
peat the open hole HFEC
inspection of the fastener
holes common to the under-
wing longeron fitting, upper
drag splice angle, and low-
er drag splice angle for any
crack.
-Before further flight.CONDITION 8.2.1 (OP-
TION 2): Contact The Boe-
ing Company for any possi-
ble underwing longeron fit-
ting hole repair instructions
and do the repair.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 10, 2024
767-57A0148 RB
27 of 416
REQUIREMENTS BULLETIN 767-57A0148
ALERTALERT

### Page 28

Group 1, Configuration 1-2; Group 2, Configuration 1-2; Group 3, Configuration 1-2; Group 4, Configuration
1-4; Group 5, Configuration 1-2; Group 6, Configuration 1-2; Group 7, Configuration 1-4:
Table 2: Right Side Underwing Longeron Fitting Forward Lower Fastener Holes Inspection
Repeat Interval
(Not to Exceed)
Boeing Recommended
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flight.CONDITION 8.2.2 (OP-
TION 1) (ACTION 1): Con-
tact The Boeing Company
for any tension bolt fasten-
er stack-up repair and any
front spar lower chord re-
pair instructions and do the
repair.
CONDITION 8.2.2: ANY
CRACK FOUND AS A RE-
SULT OF CONDITION 8.2
INSPECTION.
-Before further flight.CONDITION 8.2.2 (OP-
TION 1) (ACTION 2): Re-
place the underwing
longeron fitting with new
underwing longeron fitting.
22,000 flight-cy-
cles or 80,000
flight-hours,
whichever oc-
curs first.
-CONDITION 8.2.2 (OP-
TION 1) (ACTION 3): Re-
peat the open hole HFEC
inspection of the fastener
holes common to the under-
wing longeron fitting, upper
drag splice angle, and low-
er drag splice angle for any
crack.
-Before further flight.CONDITION 8.2.2 (OP-
TION 2): Contact The Boe-
ing Company for any ten-
sion bolt fastener stack-up
repair, any front spar lower
chord repair, and any possi-
ble underwing longeron fit-
ting hole repair instructions
and do the repair.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 10, 2024
767-57A0148 RB
28 of 416
REQUIREMENTS BULLETIN 767-57A0148
ALERTALERT

### Page 29

Group 1, Configuration 1-2; Group 2, Configuration 1-2; Group 3, Configuration 1-2; Group 4, Configuration
1-4; Group 5, Configuration 1-2; Group 6, Configuration 1-2; Group 7, Configuration 1-4:
Table 2: Right Side Underwing Longeron Fitting Forward Lower Fastener Holes Inspection
Repeat Interval
(Not to Exceed)
Boeing Recommended
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flight.Do an open hole HFEC in-
spection of the entire fasten-
er stack-up common to the
tension bolt hole and a sur-
face HFEC inspection of
the front spar lower chord
for any crack.
CONDITION 8.3: ANY
CRACK FOUND THAT IS
MORE THAN THE SEC-
OND HOLE OVERSIZE
FROM NOMINAL AT A
FASTENER HOLE ON
THE UPPER DRAG
SPLICE ANGLE OR THE
LOWER DRAG SPLICE
ANGLE BUT NO CRACK
FOUND ON THE UNDER-
WING LONGERON FIT-
TING, AS A RESULT OF
CONDITION 8 (ACTION 2)
INSPECTION.
-Before further flight.Contact The Boeing Com-
pany for any upper drag
splice angle repair and any
lower drag splice angle re-
pair instructions and do the
repair.
CONDITION 8.3.1: NO
CRACK FOUND AS A RE-
SULT OF CONDITION 8.3
INSPECTION.
-Before further flight.Contact The Boeing Com-
pany for any upper drag
splice angle repair, any
lower drag splice angle re-
pair, any tension bolt fasten-
er stack-up repair, and any
front spar lower chord re-
pair instructions and do the
repair.
CONDITION 8.3.2: ANY
CRACK FOUND AS A RE-
SULT OF CONDITION 8.3
INSPECTION.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 10, 2024
767-57A0148 RB
29 of 416
REQUIREMENTS BULLETIN 767-57A0148
ALERTALERT

### Page 30

Group 1, Configuration 1-2; Group 2, Configuration 1-2; Group 3, Configuration 1-2; Group 4, Configuration
1-4; Group 5, Configuration 1-2; Group 6, Configuration 1-2; Group 7, Configuration 1-4:
Table 2: Right Side Underwing Longeron Fitting Forward Lower Fastener Holes Inspection
Repeat Interval
(Not to Exceed)
Boeing Recommended
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flight.Do an open hole HFEC in-
spection of the entire fasten-
er stack-up common to the
tension bolt hole and a sur-
face HFEC inspection of
the front spar lower chord
for any crack.
CONDITION 8.4: ANY
CRACK FOUND THAT IS
MORE THAN THE SEC-
OND HOLE OVERSIZE
FROM NOMINAL AT A
FASTENER HOLE ON
THE UNDERWING
LONGERON FITTING,
AND EITHER THE UPPER
DRAG SPLICE ANGLE OR
THE LOWER DRAG
SPLICE ANGLE AS A RE-
SULT OF CONDITION 8
(ACTION 2) INSPECTION.
-Before further flight.Contact The Boeing Com-
pany for any upper drag
splice angle repair, any
lower drag splice angle re-
pair, and any possible un-
derwing longeron fitting
hole repair instructions and
do the repair.
CONDITION 8.4.1: NO
CRACK FOUND AS A RE-
SULT OF CONDITION 8.4
INSPECTION.
-Before further flight.Contact The Boeing Com-
pany for any upper drag
splice angle repair, any
lower drag splice angle re-
pair, any tension bolt fasten-
er stack-up repair, any front
spar lower chord repair,
and any possible under-
wing longeron fitting hole
repair instructions and do
the repair.
CONDITION 8.4.2: ANY
CRACK FOUND AS A RE-
SULT OF CONDITION 8.4
INSPECTION.
(a) Do the oversize hole repair by reaming in 1/64 inch increments to a maximum diameter of 0.6567 (maximum
diameter for 2nd oversize of nominal production fastener).
(b) Do the open hole HFEC inspection after each incremental oversize reaming operation to confirm a crack-
free condition.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 10, 2024
767-57A0148 RB
30 of 416
REQUIREMENTS BULLETIN 767-57A0148
ALERTALERT

### Page 31

Group 1, Configuration 2, 4; Group 2, Configuration 2, 4; Group 3, Configuration 2, 4; Group 4, Configu-
ration 3-4, 7-8; Group 5, Configuration 2, 4; Group 6, Configuration 2, 4; Group 7, Configuration 3-4, 7-
8:
Table 3: Left Side Underwing Longeron Fitting Forward Lower Fastener Holes Inspection
Repeat Interval
(Not to Exceed)
Boeing Recommended
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Within 6,000
flight-cycles or
14,000 flight-
hours after the
Original Issue
date of Require-
ments Bulletin
767-57A0148
RB, whichever
occurs first.
Within 22,000
flight-cycles or
80,000 flight-
hours after the
replacement of
the underwing
longeron fitting,
whichever oc-
curs first.
Do an open hole High Fre-
quency Eddy Current
(HFEC) inspection of the
fastener holes common to
the underwing longeron fit-
ting, upper drag splice an-
gle, and lower drag splice
angle for any crack.
All Airplanes.
-Before further flight.CONDITION 9 (ACTION 1):
Install fasteners.
CONDITION 9: NO CRACK
FOUND.
12,000 flight-cy-
cles or 28,000
flight-hours,
whichever oc-
curs first.
-CONDITION 9 (ACTION 2):
Repeat the open hole
HFEC inspection of the
fastener holes common to
the underwing longeron fit-
ting, upper drag splice an-
gle, and lower drag splice
angle for any crack.
-Before further flight.CONDITION 10 (ACTION
1): Do hole oversize repair
at the affected hole loca-
tion(s), through all fittings
and angles in the joint. (a)
CONDITION 10: ANY
CRACK FOUND ON THE
UNDERWING LONGERON
FITTING AND NO CRACK
FOUND ON THE UPPER
DRAG SPLICE ANGLE OR
THE LOWER DRAG
SPLICE ANGLE.
-Before further flight.CONDITION 10 (ACTION
2): At oversize hole repair
location(s), do an open
hole HFEC inspection of
the fitting and angles for
any crack. (b)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 10, 2024
767-57A0148 RB
31 of 416
REQUIREMENTS BULLETIN 767-57A0148
ALERTALERT

### Page 32

Group 1, Configuration 2, 4; Group 2, Configuration 2, 4; Group 3, Configuration 2, 4; Group 4, Configu-
ration 3-4, 7-8; Group 5, Configuration 2, 4; Group 6, Configuration 2, 4; Group 7, Configuration 3-4, 7-
8:
Table 3: Left Side Underwing Longeron Fitting Forward Lower Fastener Holes Inspection
Repeat Interval
(Not to Exceed)
Boeing Recommended
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flight.CONDITION 10.1 (ACTION
1): Install fasteners.
CONDITION 10.1: NO
CRACK FOUND AS A RE-
SULT OF CONDITION 10
(ACTION 2) INSPECTION. 12,000 flight-cy-cles or 28,000
flight-hours,
whichever oc-
curs first.
-CONDITION 10.1 (ACTION
2): Repeat the open hole
HFEC inspection of the
fastener holes common to
the underwing longeron fit-
ting, upper drag splice an-
gle, and lower drag splice
angle for any crack.
-Before further flight.Do an open hole HFEC in-
spection of the entire fasten-
er stack-up common to the
tension bolt hole and a sur-
face HFEC inspection of
the front spar lower chord
for any crack.
CONDITION 10.2: ANY
CRACK FOUND THAT IS
MORE THAN THE SEC-
OND HOLE OVERSIZE
FROM NOMINAL AS A
RESULT OF CONDITION
10 (ACTION 2) INSPEC-
TION.
-Before further flight.CONDITION 10.2.1 (OP-
TION 1) (ACTION 1): Re-
place the underwing
longeron fitting with new
underwing longeron fitting.
CONDITION 10.2.1: NO
CRACK FOUND AS A RE-
SULT OF CONDITION
10.2 INSPECTION.
22,000 flight-cy-
cles or 80,000
flight-hours,
whichever oc-
curs first.
-CONDITION 10.2.1 (OP-
TION 1) (ACTION 2): Re-
peat the open hole HFEC
inspection of the fastener
holes common to the under-
wing longeron fitting, upper
drag splice angle, and low-
er drag splice angle for any
crack.
-Before further flight.CONDITION 10.2.1 (OP-
TION 2): Contact The Boe-
ing Company for any possi-
ble underwing longeron fit-
ting hole repair instructions
and do the repair.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 10, 2024
767-57A0148 RB
32 of 416
REQUIREMENTS BULLETIN 767-57A0148
ALERTALERT

### Page 33

Group 1, Configuration 2, 4; Group 2, Configuration 2, 4; Group 3, Configuration 2, 4; Group 4, Configu-
ration 3-4, 7-8; Group 5, Configuration 2, 4; Group 6, Configuration 2, 4; Group 7, Configuration 3-4, 7-
8:
Table 3: Left Side Underwing Longeron Fitting Forward Lower Fastener Holes Inspection
Repeat Interval
(Not to Exceed)
Boeing Recommended
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flight.CONDITION 10.2.2 (OP-
TION 1) (ACTION 1): Con-
tact The Boeing Company
for any tension bolt fasten-
er stack-up repair and any
front spar lower chord re-
pair instructions and do the
repair.
CONDITION 10.2.2: ANY
CRACK FOUND AS A RE-
SULT OF CONDITION
10.2 INSPECTION.
-Before further flight.CONDITION 10.2.2 (OP-
TION 1) (ACTION 2): Re-
place the underwing
longeron fitting with new
underwing longeron fitting.
22,000 flight-cy-
cles or 80,000
flight-hours,
whichever oc-
curs first.
-CONDITION 10.2.2 (OP-
TION 1) (ACTION 3): Re-
peat the open hole HFEC
inspection of the fastener
holes common to the under-
wing longeron fitting, upper
drag splice angle, and low-
er drag splice angle for any
crack.
-Before further flight.CONDITION 10.2.2 (OP-
TION 2): Contact The Boe-
ing Company for any ten-
sion bolt fastener stack-up
repair, any front spar lower
chord repair, and any possi-
ble underwing longeron fit-
ting hole repair instructions
and do the repair.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 10, 2024
767-57A0148 RB
33 of 416
REQUIREMENTS BULLETIN 767-57A0148
ALERTALERT

### Page 34

Group 1, Configuration 2, 4; Group 2, Configuration 2, 4; Group 3, Configuration 2, 4; Group 4, Configu-
ration 3-4, 7-8; Group 5, Configuration 2, 4; Group 6, Configuration 2, 4; Group 7, Configuration 3-4, 7-
8:
Table 3: Left Side Underwing Longeron Fitting Forward Lower Fastener Holes Inspection
Repeat Interval
(Not to Exceed)
Boeing Recommended
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flight.CONDITION 11 (ACTION
1): Do hole oversize repair
at the affected hole loca-
tion(s), through all fittings
and angles in the joint. (a)
CONDITION 11: ANY
CRACK FOUND ON THE
UPPER DRAG SPLICE
ANGLE OR THE LOWER
DRAG SPLICE ANGLE
AND NO CRACK FOUND
ON THE UNDERWING
LONGERON FITTING.
-Before further flight.CONDITION 11 (ACTION
2): At oversize hole repair
location(s), do an open
hole HFEC inspection of
the fitting and angles for
any crack. (b)
-Before further flight.CONDITION 11.1 (ACTION
1): Install fasteners.
CONDITION 11.1: NO
CRACK FOUND AS A RE-
SULT OF CONDITION 11
(ACTION 2) INSPECTION. 12,000 flight-cy-cles or 28,000
flight-hours,
whichever oc-
curs first.
-CONDITION 11.1 (ACTION
2): Repeat the open hole
HFEC inspection of the
fastener holes common to
the underwing longeron fit-
ting, upper drag splice an-
gle, and lower drag splice
angle for any crack.
-Before further flight.Do an open hole HFEC in-
spection of the entire fasten-
er stack-up common to the
tension bolt hole and a sur-
face HFEC inspection of
the front spar lower chord
for any crack.
CONDITION 11.2: ANY
CRACK FOUND THAT IS
MORE THAN THE SEC-
OND HOLE OVERSIZE
FROM NOMINAL AS A
RESULT OF CONDITION
11 (ACTION 2) INSPEC-
TION.
-Before further flight.Contact The Boeing Com-
pany for any upper drag
splice angle repair and any
lower drag splice angle re-
pair instructions and do the
repair.
CONDITION 11.2.1: NO
CRACK FOUND AS A RE-
SULT OF CONDITION
11.2 INSPECTION.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 10, 2024
767-57A0148 RB
34 of 416
REQUIREMENTS BULLETIN 767-57A0148
ALERTALERT

### Page 35

Group 1, Configuration 2, 4; Group 2, Configuration 2, 4; Group 3, Configuration 2, 4; Group 4, Configu-
ration 3-4, 7-8; Group 5, Configuration 2, 4; Group 6, Configuration 2, 4; Group 7, Configuration 3-4, 7-
8:
Table 3: Left Side Underwing Longeron Fitting Forward Lower Fastener Holes Inspection
Repeat Interval
(Not to Exceed)
Boeing Recommended
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flight.Contact The Boeing Com-
pany for any upper drag
splice angle repair, any
lower drag splice angle re-
pair, any tension bolt fasten-
er stack-up repair, and any
front spar lower chord re-
pair instructions and do the
repair.
CONDITION 11.2.2: ANY
CRACK FOUND AS A RE-
SULT OF CONDITION
11.2 INSPECTION.
-Before further flight.CONDITION 12 (ACTION
1): Do hole oversize repair
at the affected hole loca-
tion(s), through all fittings
and angles in the joint. (a)
CONDITION 12: ANY
CRACK FOUND ON THE
UNDERWING LONGERON
FITTING AND ANY
CRACK FOUND ON EI-
THER THE UPPER DRAG
SPLICE ANGLE OR THE
LOWER DRAG SPLICE
ANGLE.
-Before further flight.CONDITION 12 (ACTION
2): At oversize hole repair
location(s), do an open
hole HFEC inspection of
the fitting and angles for
any crack. (b)
-Before further flight.CONDITION 12.1 (ACTION
1): Install fasteners.
CONDITION 12.1: NO
CRACK FOUND AS A RE-
SULT OF CONDITION 12
(ACTION 2) INSPECTION. 12,000 flight-cy-cles or 28,000
flight-hours,
whichever oc-
curs first.
-CONDITION 12.1 (ACTION
2): Repeat the open hole
HFEC inspection of the
fastener holes common to
the underwing longeron fit-
ting, upper drag splice an-
gle, and lower drag splice
angle for any crack.
-Before further flight.Do an open hole HFEC in-
spection of the entire fasten-
er stack-up common to the
tension bolt hole and a sur-
face HFEC inspection of
the front spar lower chord
for any crack.
CONDITION 12.2: ANY
CRACK FOUND THAT IS
MORE THAN THE SEC-
OND HOLE OVERSIZE
FROM NOMINAL AT A
FASTENER HOLE ON
THE UNDERWING
LONGERON FITTING ON-
LY, AS A RESULT OF
CONDITION 12 (ACTION
2) INSPECTION.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 10, 2024
767-57A0148 RB
35 of 416
REQUIREMENTS BULLETIN 767-57A0148
ALERTALERT

### Page 36

Group 1, Configuration 2, 4; Group 2, Configuration 2, 4; Group 3, Configuration 2, 4; Group 4, Configu-
ration 3-4, 7-8; Group 5, Configuration 2, 4; Group 6, Configuration 2, 4; Group 7, Configuration 3-4, 7-
8:
Table 3: Left Side Underwing Longeron Fitting Forward Lower Fastener Holes Inspection
Repeat Interval
(Not to Exceed)
Boeing Recommended
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flight.CONDITION 12.2.1 (OP-
TION 1) (ACTION 1): Re-
place the underwing
longeron fitting with new
underwing longeron fitting.
CONDITION 12.2.1: NO
CRACK FOUND AS A RE-
SULT OF CONDITION
12.2 INSPECTION.
22,000 flight-cy-
cles or 80,000
flight-hours,
whichever oc-
curs first.
-CONDITION 12.2.1 (OP-
TION 1) (ACTION 2): Re-
peat the open hole HFEC
inspection of the fastener
holes common to the under-
wing longeron fitting, upper
drag splice angle, and low-
er drag splice angle for any
crack.
-Before further flight.CONDITION 12.2.1 (OP-
TION 2): Contact The Boe-
ing Company for any possi-
ble underwing longeron fit-
ting hole repair instructions
and do the repair.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 10, 2024
767-57A0148 RB
36 of 416
REQUIREMENTS BULLETIN 767-57A0148
ALERTALERT

### Page 37

Group 1, Configuration 2, 4; Group 2, Configuration 2, 4; Group 3, Configuration 2, 4; Group 4, Configu-
ration 3-4, 7-8; Group 5, Configuration 2, 4; Group 6, Configuration 2, 4; Group 7, Configuration 3-4, 7-
8:
Table 3: Left Side Underwing Longeron Fitting Forward Lower Fastener Holes Inspection
Repeat Interval
(Not to Exceed)
Boeing Recommended
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flight.CONDITION 12.2.2 (OP-
TION 1) (ACTION 1): Con-
tact The Boeing Company
for any tension bolt fasten-
er stack-up repair and any
front spar lower chord re-
pair instructions and do the
repair.
CONDITION 12.2.2: ANY
CRACK FOUND AS A RE-
SULT OF CONDITION
12.2 INSPECTION.
-Before further flight.CONDITION 12.2.2 (OP-
TION 1) (ACTION 2): Re-
place the underwing
longeron fitting with new
underwing longeron fitting.
22,000 flight-cy-
cles or 80,000
flight-hours,
whichever oc-
curs first.
-CONDITION 12.2.2 (OP-
TION 1) (ACTION 3): Re-
peat the open hole HFEC
inspection of the fastener
holes common to the under-
wing longeron fitting, upper
drag splice angle, and low-
er drag splice angle for any
crack.
-Before further flight.CONDITION 12.2.2 (OP-
TION 2): Contact The Boe-
ing Company for any ten-
sion bolt fastener stack-up
repair, any front spar lower
chord repair, and any possi-
ble underwing longeron fit-
ting hole repair instructions
and do the repair.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 10, 2024
767-57A0148 RB
37 of 416
REQUIREMENTS BULLETIN 767-57A0148
ALERTALERT

### Page 38

Group 1, Configuration 2, 4; Group 2, Configuration 2, 4; Group 3, Configuration 2, 4; Group 4, Configu-
ration 3-4, 7-8; Group 5, Configuration 2, 4; Group 6, Configuration 2, 4; Group 7, Configuration 3-4, 7-
8:
Table 3: Left Side Underwing Longeron Fitting Forward Lower Fastener Holes Inspection
Repeat Interval
(Not to Exceed)
Boeing Recommended
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flight.Do an open hole HFEC in-
spection of the entire fasten-
er stack-up common to the
tension bolt hole and a sur-
face HFEC inspection of
the front spar lower chord
for any crack.
CONDITION 12.3: ANY
CRACK FOUND THAT IS
MORE THAN THE SEC-
OND HOLE OVERSIZE
FROM NOMINAL AT A
FASTENER HOLE ON
THE UPPER DRAG
SPLICE ANGLE OR THE
LOWER DRAG SPLICE
ANGLE BUT NO CRACK
FOUND ON THE UNDER-
WING LONGERON FIT-
TING, AS A RESULT OF
CONDITION 12 (ACTION
2) INSPECTION.
-Before further flight.Contact The Boeing Com-
pany for any upper drag
splice angle repair and any
lower drag splice angle re-
pair instructions and do the
repair.
CONDITION 12.3.1: NO
CRACK FOUND AS A RE-
SULT OF CONDITION
12.3 INSPECTION.
-Before further flight.Contact The Boeing Com-
pany for any upper drag
splice angle repair, any
lower drag splice angle re-
pair, any tension bolt fasten-
er stack-up repair, and any
front spar lower chord re-
pair instructions and do the
repair.
CONDITION 12.3.2: ANY
CRACK FOUND AS A RE-
SULT OF CONDITION
12.3 INSPECTION.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 10, 2024
767-57A0148 RB
38 of 416
REQUIREMENTS BULLETIN 767-57A0148
ALERTALERT

### Page 39

Group 1, Configuration 2, 4; Group 2, Configuration 2, 4; Group 3, Configuration 2, 4; Group 4, Configu-
ration 3-4, 7-8; Group 5, Configuration 2, 4; Group 6, Configuration 2, 4; Group 7, Configuration 3-4, 7-
8:
Table 3: Left Side Underwing Longeron Fitting Forward Lower Fastener Holes Inspection
Repeat Interval
(Not to Exceed)
Boeing Recommended
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flight.Do an open hole HFEC in-
spection of the entire fasten-
er stack-up common to the
tension bolt hole and a sur-
face HFEC inspection of
the front spar lower chord
for any crack.
CONDITION 12.4: ANY
CRACK FOUND THAT IS
MORE THAN THE SEC-
OND HOLE OVERSIZE
FROM NOMINAL AT A
FASTENER HOLE ON
THE UNDERWING
LONGERON FITTING,
AND EITHER THE UPPER
DRAG SPLICE ANGLE OR
THE LOWER DRAG
SPLICE ANGLE AS A RE-
SULT OF CONDITION 12
(ACTION 2) INSPECTION.
-Before further flight.Contact The Boeing Com-
pany for any upper drag
splice angle repair, any
lower drag splice angle re-
pair, and any possible un-
derwing longeron fitting
hole repair instructions and
do the repair.
CONDITION 12.4.1: NO
CRACK FOUND AS A RE-
SULT OF CONDITION
12.4 INSPECTION.
-Before further flight.Contact The Boeing Com-
pany for any upper drag
splice angle repair, any
lower drag splice angle re-
pair, any tension bolt fasten-
er stack-up repair, any front
spar lower chord repair,
and any possible under-
wing longeron fitting hole
repair instructions and do
the repair.
CONDITION 12.4.2: ANY
CRACK FOUND AS A RE-
SULT OF CONDITION
12.4 INSPECTION.
(a) Do the oversize hole repair by reaming in 1/64 inch increments to a maximum diameter of 0.6567 (maximum
diameter for 2nd oversize of nominal production fastener).
(b) Do the open hole HFEC inspection after each incremental oversize reaming operation to confirm a crack-
free condition.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 10, 2024
767-57A0148 RB
39 of 416
REQUIREMENTS BULLETIN 767-57A0148
ALERTALERT

### Page 40

Group 1, Configuration 3-4; Group 2, Configuration 3-4; Group 3, Configuration 3-4; Group 4, Configuration
5-8; Group 5, Configuration 3-4; Group 6, Configuration 3-4; Group 7, Configuration 5-8:
Table 4: Right Side Underwing Longeron Fitting Forward Lower Fastener Holes Inspection
Repeat Interval
(Not to Exceed)
Boeing Recommended
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Within 6,000
flight-cycles or
14,000 flight-
hours after the
Original Issue
date of Require-
ments Bulletin
767-57A0148
RB, whichever
occurs first.
Within 22,000
flight-cycles or
80,000 flight-
hours after the
replacement of
the underwing
longeron fitting,
whichever oc-
curs first.
Do an open hole High Fre-
quency Eddy Current
(HFEC) inspection of the
fastener holes common to
the underwing longeron fit-
ting, upper drag splice an-
gle, and lower drag splice
angle for any crack.
All Airplanes.
-Before further flight.CONDITION 13 (ACTION
1): Install fasteners.
CONDITION 13: NO
CRACK FOUND.
12,000 flight-cy-
cles or 28,000
flight-hours,
whichever oc-
curs first.
-CONDITION 13 (ACTION
2): Repeat the open hole
HFEC inspection of the
fastener holes common to
the underwing longeron fit-
ting, upper drag splice an-
gle, and lower drag splice
angle for any crack.
-Before further flight.CONDITION 14 (ACTION
1): Do hole oversize repair
at the affected hole loca-
tion(s), through all fittings
and angles in the joint. (a)
CONDITION 14: ANY
CRACK FOUND ON THE
UNDERWING LONGERON
FITTING AND NO CRACK
FOUND ON THE UPPER
DRAG SPLICE ANGLE OR
THE LOWER DRAG
SPLICE ANGLE.
-Before further flight.CONDITION 14 (ACTION
2): At oversize hole repair
location(s), do an open
hole HFEC inspection of
the fitting and angles for
any crack. (b)
-Before further flight.CONDITION 14.1 (ACTION
1): Install fasteners.
CONDITION 14.1: NO
CRACK FOUND AS A RE-
SULT OF CONDITION 14
(ACTION 2) INSPECTION. 12,000 flight-cy-cles or 28,000
flight-hours,
whichever oc-
curs first.
-CONDITION 14.1 (ACTION
2): Repeat the open hole
HFEC inspection of the
fastener holes common to
the underwing longeron fit-
ting, upper drag splice an-
gle, and lower drag splice
angle for any crack.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 10, 2024
767-57A0148 RB
40 of 416
REQUIREMENTS BULLETIN 767-57A0148
ALERTALERT

### Page 41

Group 1, Configuration 3-4; Group 2, Configuration 3-4; Group 3, Configuration 3-4; Group 4, Configuration
5-8; Group 5, Configuration 3-4; Group 6, Configuration 3-4; Group 7, Configuration 5-8:
Table 4: Right Side Underwing Longeron Fitting Forward Lower Fastener Holes Inspection
Repeat Interval
(Not to Exceed)
Boeing Recommended
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flight.Do an open hole HFEC in-
spection of the entire fasten-
er stack-up common to the
tension bolt hole and a sur-
face HFEC inspection of
the front spar lower chord
for any crack.
CONDITION 14.2: ANY
CRACK FOUND THAT IS
MORE THAN THE SEC-
OND HOLE OVERSIZE
FROM NOMINAL AS A
RESULT OF CONDITION
14 (ACTION 2) INSPEC-
TION.
-Before further flight.CONDITION 14.2.1 (OP-
TION 1) (ACTION 1): Re-
place the underwing
longeron fitting with new
underwing longeron fitting.
CONDITION 14.2.1: NO
CRACK FOUND AS A RE-
SULT OF CONDITION
14.2 INSPECTION.
22,000 flight-cy-
cles or 80,000
flight-hours,
whichever oc-
curs first.
-CONDITION 14.2.1 (OP-
TION 1) (ACTION 2): Re-
peat the open hole HFEC
inspection of the fastener
holes common to the under-
wing longeron fitting, upper
drag splice angle, and low-
er drag splice angle for any
crack.
-Before further flight.CONDITION 14.2.1 (OP-
TION 2): Contact The Boe-
ing Company for any possi-
ble underwing longeron fit-
ting hole repair instructions
and do the repair.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 10, 2024
767-57A0148 RB
41 of 416
REQUIREMENTS BULLETIN 767-57A0148
ALERTALERT

### Page 42

Group 1, Configuration 3-4; Group 2, Configuration 3-4; Group 3, Configuration 3-4; Group 4, Configuration
5-8; Group 5, Configuration 3-4; Group 6, Configuration 3-4; Group 7, Configuration 5-8:
Table 4: Right Side Underwing Longeron Fitting Forward Lower Fastener Holes Inspection
Repeat Interval
(Not to Exceed)
Boeing Recommended
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flight.CONDITION 14.2.2 (OP-
TION 1) (ACTION 1): Con-
tact The Boeing Company
for any tension bolt fasten-
er stack-up repair and any
front spar lower chord re-
pair instructions and do the
repair.
CONDITION 14.2.2: ANY
CRACK FOUND AS A RE-
SULT OF CONDITION
14.2 INSPECTION.
-Before further flight.CONDITION 14.2.2 (OP-
TION 1) (ACTION 2): Re-
place the underwing
longeron fitting with new
underwing longeron fitting.
22,000 flight-cy-
cles or 80,000
flight-hours,
whichever oc-
curs first.
-CONDITION 14.2.2 (OP-
TION 1) (ACTION 3): Re-
peat the open hole HFEC
inspection of the fastener
holes common to the under-
wing longeron fitting, upper
drag splice angle, and low-
er drag splice angle for any
crack.
-Before further flight.CONDITION 14.2.2 (OP-
TION 2): Contact The Boe-
ing Company for any ten-
sion bolt fastener stack-up
repair, any front spar lower
chord repair, and any possi-
ble underwing longeron fit-
ting hole repair instructions
and do the repair.
-Before further flight.CONDITION 15 (ACTION
1): Do hole oversize repair
at the affected hole loca-
tion(s), through all fittings
and angles in the joint. (a)
CONDITION 15: ANY
CRACK FOUND ON THE
UPPER DRAG SPLICE
ANGLE OR THE LOWER
DRAG SPLICE ANGLE
AND NO CRACK FOUND
ON THE UNDERWING
LONGERON FITTING.
-Before further flight.CONDITION 15 (ACTION
2): At oversize hole repair
location(s), do an open
hole HFEC inspection of
the fitting and angles for
any crack. (b)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 10, 2024
767-57A0148 RB
42 of 416
REQUIREMENTS BULLETIN 767-57A0148
ALERTALERT

### Page 43

Group 1, Configuration 3-4; Group 2, Configuration 3-4; Group 3, Configuration 3-4; Group 4, Configuration
5-8; Group 5, Configuration 3-4; Group 6, Configuration 3-4; Group 7, Configuration 5-8:
Table 4: Right Side Underwing Longeron Fitting Forward Lower Fastener Holes Inspection
Repeat Interval
(Not to Exceed)
Boeing Recommended
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flight.CONDITION 15.1 (ACTION
1): Install fasteners.
CONDITION 15.1: NO
CRACK FOUND AS A RE-
SULT OF CONDITION 15
(ACTION 2) INSPECTION. 12,000 flight-cy-cles or 28,000
flight-hours,
whichever oc-
curs first.
-CONDITION 15.1 (ACTION
2): Repeat the open hole
HFEC inspection of the
fastener holes common to
the underwing longeron fit-
ting, upper drag splice an-
gle, and lower drag splice
angle for any crack.
-Before further flight.Do an open hole HFEC in-
spection of the entire fasten-
er stack-up common to the
tension bolt hole and a sur-
face HFEC inspection of
the front spar lower chord
for any crack.
CONDITION 15.2: ANY
CRACK FOUND THAT IS
MORE THAN THE SEC-
OND HOLE OVERSIZE
FROM NOMINAL AS A
RESULT OF CONDITION
15 (ACTION 2) INSPEC-
TION.
-Before further flight.Contact The Boeing Com-
pany for any upper drag
splice angle repair and any
lower drag splice angle re-
pair instructions and do the
repair.
CONDITION 15.2.1: NO
CRACK FOUND AS A RE-
SULT OF CONDITION
15.2 INSPECTION.
-Before further flight.Contact The Boeing Com-
pany for any upper drag
splice angle repair, any
lower drag splice angle re-
pair, any tension bolt fasten-
er stack-up repair, and any
front spar lower chord re-
pair instructions and do the
repair.
CONDITION 15.2.2: ANY
CRACK FOUND AS A RE-
SULT OF CONDITION
15.2 INSPECTION.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 10, 2024
767-57A0148 RB
43 of 416
REQUIREMENTS BULLETIN 767-57A0148
ALERTALERT

### Page 44

Group 1, Configuration 3-4; Group 2, Configuration 3-4; Group 3, Configuration 3-4; Group 4, Configuration
5-8; Group 5, Configuration 3-4; Group 6, Configuration 3-4; Group 7, Configuration 5-8:
Table 4: Right Side Underwing Longeron Fitting Forward Lower Fastener Holes Inspection
Repeat Interval
(Not to Exceed)
Boeing Recommended
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flight.CONDITION 16 (ACTION
1): Do hole oversize repair
at the affected hole loca-
tion(s), through all fittings
and angles in the joint. (a)
CONDITION 16: ANY
CRACK FOUND ON THE
UNDERWING LONGERON
FITTING AND ANY
CRACK FOUND ON EI-
THER THE UPPER DRAG
SPLICE ANGLE OR THE
LOWER DRAG SPLICE
ANGLE.
-Before further flight.CONDITION 16 (ACTION
2): At oversize hole repair
location(s), do an open
hole HFEC inspection of
the fitting and angles for
any crack. (b)
-Before further flight.CONDITION 16.1 (ACTION
1): Install fasteners.
CONDITION 16.1: NO
CRACK FOUND AS A RE-
SULT OF CONDITION 16
(ACTION 2) INSPECTION. 12,000 flight-cy-cles or 28,000
flight-hours,
whichever oc-
curs first.
-CONDITION 16.1 (ACTION
2): Repeat the open hole
HFEC inspection of the
fastener holes common to
the underwing longeron fit-
ting, upper drag splice an-
gle, and lower drag splice
angle for any crack.
-Before further flight.Do an open hole HFEC in-
spection of the entire fasten-
er stack-up common to the
tension bolt hole and a sur-
face HFEC inspection of
the front spar lower chord
for any crack.
CONDITION 16.2: ANY
CRACK FOUND THAT IS
MORE THAN THE SEC-
OND HOLE OVERSIZE
FROM NOMINAL AT A
FASTENER HOLE ON
THE UNDERWING
LONGERON FITTING ON-
LY, AS A RESULT OF
CONDITION 16 (ACTION
2) INSPECTION.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 10, 2024
767-57A0148 RB
44 of 416
REQUIREMENTS BULLETIN 767-57A0148
ALERTALERT

### Page 45

Group 1, Configuration 3-4; Group 2, Configuration 3-4; Group 3, Configuration 3-4; Group 4, Configuration
5-8; Group 5, Configuration 3-4; Group 6, Configuration 3-4; Group 7, Configuration 5-8:
Table 4: Right Side Underwing Longeron Fitting Forward Lower Fastener Holes Inspection
Repeat Interval
(Not to Exceed)
Boeing Recommended
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flight.CONDITION 16.2.1 (OP-
TION 1) (ACTION 1): Re-
place the underwing
longeron fitting with new
underwing longeron fitting.
CONDITION 16.2.1: NO
CRACK FOUND AS A RE-
SULT OF CONDITION
16.2 INSPECTION.
22,000 flight-cy-
cles or 80,000
flight-hours,
whichever oc-
curs first.
-CONDITION 16.2.1 (OP-
TION 1) (ACTION 2): Re-
peat the open hole HFEC
inspection of the fastener
holes common to the under-
wing longeron fitting, upper
drag splice angle, and low-
er drag splice angle for any
crack.
-Before further flight.CONDITION 16.2.1 (OP-
TION 2): Contact The Boe-
ing Company for any possi-
ble underwing longeron fit-
ting hole repair instructions
and do the repair.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 10, 2024
767-57A0148 RB
45 of 416
REQUIREMENTS BULLETIN 767-57A0148
ALERTALERT

### Page 46

Group 1, Configuration 3-4; Group 2, Configuration 3-4; Group 3, Configuration 3-4; Group 4, Configuration
5-8; Group 5, Configuration 3-4; Group 6, Configuration 3-4; Group 7, Configuration 5-8:
Table 4: Right Side Underwing Longeron Fitting Forward Lower Fastener Holes Inspection
Repeat Interval
(Not to Exceed)
Boeing Recommended
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flight.CONDITION 16.2.2 (OP-
TION 1) (ACTION 1): Con-
tact The Boeing Company
for any tension bolt fasten-
er stack-up repair and any
front spar lower chord re-
pair instructions and do the
repair.
CONDITION 16.2.2: ANY
CRACK FOUND AS A RE-
SULT OF CONDITION
16.2 INSPECTION.
-Before further flight.CONDITION 16.2.2 (OP-
TION 1) (ACTION 2): Re-
place the underwing
longeron fitting with new
underwing longeron fitting.
22,000 flight-cy-
cles or 80,000
flight-hours,
whichever oc-
curs first.
-CONDITION 16.2.2 (OP-
TION 1) (ACTION 3): Re-
peat the open hole HFEC
inspection of the fastener
holes common to the under-
wing longeron fitting, upper
drag splice angle, and low-
er drag splice angle for any
crack.
-Before further flight.CONDITION 16.2.2 (OP-
TION 2): Contact The Boe-
ing Company for any ten-
sion bolt fastener stack-up
repair, any front spar lower
chord repair, and any possi-
ble underwing longeron fit-
ting hole repair instructions
and do the repair.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 10, 2024
767-57A0148 RB
46 of 416
REQUIREMENTS BULLETIN 767-57A0148
ALERTALERT

### Page 47

Group 1, Configuration 3-4; Group 2, Configuration 3-4; Group 3, Configuration 3-4; Group 4, Configuration
5-8; Group 5, Configuration 3-4; Group 6, Configuration 3-4; Group 7, Configuration 5-8:
Table 4: Right Side Underwing Longeron Fitting Forward Lower Fastener Holes Inspection
Repeat Interval
(Not to Exceed)
Boeing Recommended
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flight.Do an open hole HFEC in-
spection of the entire fasten-
er stack-up common to the
tension bolt hole and a sur-
face HFEC inspection of
the front spar lower chord
for any crack.
CONDITION 16.3: ANY
CRACK FOUND THAT IS
MORE THAN THE SEC-
OND HOLE OVERSIZE
FROM NOMINAL AT A
FASTENER HOLE ON
THE UPPER DRAG
SPLICE ANGLE OR THE
LOWER DRAG SPLICE
ANGLE BUT NO CRACK
FOUND ON THE UNDER-
WING LONGERON FIT-
TING, AS A RESULT OF
CONDITION 16 (ACTION
2) INSPECTION.
-Before further flight.Contact The Boeing Com-
pany for any upper drag
splice angle repair and any
lower drag splice angle re-
pair instructions and do the
repair.
CONDITION 16.3.1: NO
CRACK FOUND AS A RE-
SULT OF CONDITION
16.3 INSPECTION.
-Before further flight.Contact The Boeing Com-
pany for any upper drag
splice angle repair, any
lower drag splice angle re-
pair, any tension bolt fasten-
er stack-up repair, and any
front spar lower chord re-
pair instructions and do the
repair.
CONDITION 16.3.2: ANY
CRACK FOUND AS A RE-
SULT OF CONDITION
16.3 INSPECTION.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 10, 2024
767-57A0148 RB
47 of 416
REQUIREMENTS BULLETIN 767-57A0148
ALERTALERT

### Page 48

Group 1, Configuration 3-4; Group 2, Configuration 3-4; Group 3, Configuration 3-4; Group 4, Configuration
5-8; Group 5, Configuration 3-4; Group 6, Configuration 3-4; Group 7, Configuration 5-8:
Table 4: Right Side Underwing Longeron Fitting Forward Lower Fastener Holes Inspection
Repeat Interval
(Not to Exceed)
Boeing Recommended
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flight.Do an open hole HFEC in-
spection of the entire fasten-
er stack-up common to the
tension bolt hole and a sur-
face HFEC inspection of
the front spar lower chord
for any crack.
CONDITION 16.4: ANY
CRACK FOUND THAT IS
MORE THAN THE SEC-
OND HOLE OVERSIZE
FROM NOMINAL AT A
FASTENER HOLE ON
THE UNDERWING
LONGERON FITTING,
AND EITHER THE UPPER
DRAG SPLICE ANGLE OR
THE LOWER DRAG
SPLICE ANGLE AS A RE-
SULT OF CONDITION 16
(ACTION 2) INSPECTION.
-Before further flight.Contact The Boeing Com-
pany for any upper drag
splice angle repair, any
lower drag splice angle re-
pair, and any possible un-
derwing longeron fitting
hole repair instructions and
do the repair.
CONDITION 16.4.1: NO
CRACK FOUND AS A RE-
SULT OF CONDITION
16.4 INSPECTION.
-Before further flight.Contact The Boeing Com-
pany for any upper drag
splice angle repair, any
lower drag splice angle re-
pair, any tension bolt fasten-
er stack-up repair, any front
spar lower chord repair,
and any possible under-
wing longeron fitting hole
repair instructions and do
the repair.
CONDITION 16.4.2: ANY
CRACK FOUND AS A RE-
SULT OF CONDITION
16.4 INSPECTION.
(a) Do the oversize hole repair by reaming in 1/64 inch increments to a maximum diameter of 0.6567 (maximum
diameter for 2nd oversize of nominal production fastener).
(b) Do the open hole HFEC inspection after each incremental oversize reaming operation to confirm a crack-
free condition.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 10, 2024
767-57A0148 RB
48 of 416
REQUIREMENTS BULLETIN 767-57A0148
ALERTALERT

### Page 49

4. APPROVAL
This Requirements Bulletin was examined by the Federal Aviation Administration (FAA). The changes
specified in this document comply with the applicable regulations and are FAA approved, as well as European
Union Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved
airplanes listed in this Requirements Bulletin effectivity. This document and its approval were based on the
airplane in its original Boeing delivery configuration or as modified by other Boeing changes.
If an airplane has a non-Boeing modification or repair that affects a component or system also affected by
this Requirements Bulletin, the operator is responsible for obtaining appropriate regulatory agency approval
before incorporating this Requirements Bulletin.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 10, 2024
767-57A0148 RB
49 of 416
REQUIREMENTS BULLETIN 767-57A0148
ALERTALERT

### Page 50

Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 10, 2024
767-57A0148 RB
50 of 416
REQUIREMENTS BULLETIN 767-57A0148
ALERTALERT
BLANK PAGE

### Page 51

5.    ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL INFORMATION
NOTE: 1. This is an Enhanced Required for Compliance document. There will be a separate
Service Bulletin (SB) and a separate Requirements Bulletin (RB). If an RB is mandated
by an Airworthiness Directive (AD), then all applicable requirements specified in the
RB must be done. In the RB, the "Refer to the listed procedures..." column of the
table(s) in the Work Instructions is for reference only. The procedures in that column
are not required by the AD and are for guidance only. For the related SB, some
locations are marked RC Start and RC End to identify the requirements that are
restated from the RB. For the related SB, the areas between RC Start and RC End,
including sub-steps and any figures identified between RC Start and RC End, must
be done to comply with the AD. Therefore, an Alternative Method of Compliance
(AMOC) is required for any deviations to steps between RC Start and RC End,
including substeps and identified figures. For the related SB, the steps not between
RC Start and RC End may be deviated from using accepted methods in accordance
with the operator's maintenance or inspection program without obtaining approval
of an AMOC; this is provided that the steps between RC Start and RC End, including
sub-steps and identified figures, can still be done as specified, and the airplane can
be put back in an airworthy condition. Figures not required for compliance are omitted
from the RB.
2. This is an Enhanced Required for Compliance document. The Boeing processes
used to create the Service Bulletin (SB) and the Requirements Bulletin (RB) ensure
that the information between "RC Start" and "RC End" in the SB are identical to the
information in the same sections (Compliance, Work Instructions...) of the RB which
the SB refers to as the related document.
3. The compliance times for the actions in WORK INSTRUCTIONS are in Compliance.
4. Boeing Service Letter 767-SL-51-036, Damage Reporting and Repair Plan/Design
Guidelines, is an acceptable procedure to request information from Boeing for
additional structural repair instructions. The Service Letter describes what information
must be provided to Boeing before a structural repair can be provided.
5. Unless shown differently, these dimensions and tolerances are used:
– Linear dimensions are in inches
– Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus
or minus 0.03 inch
– Tolerance on rivet and bolt edge margin is plus or minus 0.05 inch
– Angular tolerance is plus or minus 2 degrees
– Hole dimensions for standard solid rivets and fasteners are in Structural Repair
Manual (SRM) Chapter 51
– Torque Values:
— Values for structural fasteners are given in 767 Structural Repair Manual,
Chapter 51.
— Values for airframe maintenance tasks are included in Chapter 20 of 767
Aircraft Maintenance Manual (AMM).
— Non-standard torque values for maintenance tasks are included in the
applicable installation step.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 10, 2024
767-57A0148 RB
51 of 416
REQUIREMENTS BULLETIN 767-57A0148
ALERTALERT

### Page 52

6. These work instructions refer to procedures included in other Boeing documents.
When the words "refer to" are used and the operator has an accepted alternative
procedure, the accepted alternative procedure can be used. When the words "in
accordance with" are included in the instruction, the procedure in the Boeing document
must be used.
7. Where the work instructions include installation of a kept part, a new or serviceable
part with the same part number can be installed as an alternative to the kept part.
8. If it is necessary to remove more parts for access, you can remove those parts. If
you can get access without removing identified parts, it is not necessary to remove
all of the identified parts. Jacking and shoring limitations must be observed.
9. Use the approved fastener, process and material substitutions in accordance with
SRM Chapter 51.
10. When more than one OPTION is given for a CONDITION, do only one of the OPTION
numbers. When more than one ACTION is given for a CONDITION or an OPTION,
do all of the ACTION numbers for that CONDITION or OPTION.
11. If the length of any fastener specified in this service bulletin does not meet installation
standards given in SRM Chapter 51, then a fastener of the same specification, or
an approved substitute, with a length which meets the installation standards given
in SRM Chapter 51 may be used. In addition, washers may be installed for fastener
grip length in accordance with SRM Chapter 51. Refer to SOPM 20-50-01 for alternate
full threaded fasteners (screws) needed for installation in this service bulletin.
B. WORK INSTRUCTIONS
Actions Required for Compliance
1. Requirements
Group 1, Configuration 1, 3:
Table 1: Left Side Underwing Longeron Fitting Forward Lower Fastener Holes Inspection
Refer to the listed pro-
cedures in SB 767-
57A0148 Original Issue
or later approved revi-
sions as an accepted
procedure
Method of Com-
pliance
ActionCondition
Do PART 1: OPEN AC-
CESS
-Do an open hole High Frequency Eddy
Current (HFEC) inspection of the fastener
holes common to the underwing longeron
fitting, upper drag splice angle, and lower
drag splice angle for any crack.
All Airplanes.
-FIGURE 3
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 10, 2024
767-57A0148 RB
52 of 416
REQUIREMENTS BULLETIN 767-57A0148
ALERTALERT

### Page 53

Group 1, Configuration 1, 3:
Table 1: Left Side Underwing Longeron Fitting Forward Lower Fastener Holes Inspection
Refer to the listed pro-
cedures in SB 767-
57A0148 Original Issue
or later approved revi-
sions as an accepted
procedure
Method of Com-
pliance
ActionCondition
-FIGURE 33CONDITION 1 (ACTION 1): Install fasten-
ers.
CONDITION 1: NO
CRACK FOUND. Do PART 3: CLOSE AC-
CESS
-
Do PART 1: OPEN AC-
CESS
-CONDITION 1 (ACTION 2): Repeat the
open hole HFEC inspection of the fastener
holes common to the underwing longeron
fitting, upper drag splice angle, and lower
drag splice angle for any crack.
-FIGURE 3
-FIGURE 35CONDITION 2 (ACTION 1): Do hole over-
size repair at the affected hole location(s),
through all fittings and angles in the joint.
(a)
CONDITION 2: ANY
CRACK FOUND ON
THE UNDERWING
LONGERON FIT-
TING AND NO
CRACK FOUND ON
THE UPPER DRAG
SPLICE ANGLE OR
THE LOWER DRAG
SPLICE ANGLE.
CONDITION 2 (ACTION 2): At oversize
hole repair location(s), do an open hole
HFEC inspection of the fitting and angles
for any crack. (b)
-FIGURE 33CONDITION 2.1 (ACTION 1): Install fasten-
ers.
CONDITION 2.1:
NO CRACK FOUND
AS A RESULT OF
CONDITION 2 (AC-
TION 2) INSPEC-
TION.
Do PART 3: CLOSE AC-
CESS
-
Do PART 1: OPEN AC-
CESS
-CONDITION 2.1 (ACTION 2): Repeat the
open hole HFEC inspection of the fastener
holes common to the underwing longeron
fitting, upper drag splice angle, and lower
drag splice angle for any crack.
-FIGURE 3
Do PART 2: DEFUEL
AIRPLANE
-Do an open hole HFEC inspection of the
entire fastener stack-up common to the
tension bolt hole and a surface HFEC in-
spection of the front spar lower chord for
any crack.
CONDITION 2.2:
ANY CRACK
FOUND THAT IS
MORE THAN THE
SECOND HOLE
OVERSIZE FROM
NOMINAL AS A
RESULT OF CONDI-
TION 2 (ACTION 2)
INSPECTION.
FIGURE 11-
-FIGURE 5
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 10, 2024
767-57A0148 RB
53 of 416
REQUIREMENTS BULLETIN 767-57A0148
ALERTALERT

### Page 54

Group 1, Configuration 1, 3:
Table 1: Left Side Underwing Longeron Fitting Forward Lower Fastener Holes Inspection
Refer to the listed pro-
cedures in SB 767-
57A0148 Original Issue
or later approved revi-
sions as an accepted
procedure
Method of Com-
pliance
ActionCondition
-FIGURE 15 P/N
111T4020U7
CONDITION 2.2.1 (OPTION 1) (ACTION
1): Replace the underwing longeron fitting
with new underwing longeron fitting.
CONDITION 2.2.1:
NO CRACK FOUND
AS A RESULT OF
CONDITION 2.2 IN-
SPECTION.
or
FIGURE 17 P/N
111T4020U13
FIGURE 29-
Do PART 3: CLOSE AC-
CESS
-
Do PART 1: OPEN AC-
CESS
-CONDITION 2.2.1 (OPTION 1) (ACTION
2): Repeat the open hole HFEC inspection
of the fastener holes common to the under-
wing longeron fitting, upper drag splice
angle, and lower drag splice angle for any
crack.
-FIGURE 3
--CONDITION 2.2.1 (OPTION 2): Contact
The Boeing Company for any possible un-
derwing longeron fitting hole repair instruc-
tions and do the repair.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 10, 2024
767-57A0148 RB
54 of 416
REQUIREMENTS BULLETIN 767-57A0148
ALERTALERT

### Page 55

Group 1, Configuration 1, 3:
Table 1: Left Side Underwing Longeron Fitting Forward Lower Fastener Holes Inspection
Refer to the listed pro-
cedures in SB 767-
57A0148 Original Issue
or later approved revi-
sions as an accepted
procedure
Method of Com-
pliance
ActionCondition
--CONDITION 2.2.2 (OPTION 1) (ACTION
1): Contact The Boeing Company for any
tension bolt fastener stack-up repair and
any front spar lower chord repair instruc-
tions and do the repair.
CONDITION 2.2.2:
ANY CRACK
FOUND AS A RE-
SULT OF CONDI-
TION 2.2 INSPEC-
TION. -FIGURE 15 P/N
111T4020U7
CONDITION 2.2.2 (OPTION 1) (ACTION
2): Replace the underwing longeron fitting
with new underwing longeron fitting. or
FIGURE 17 P/N
111T4020U13
FIGURE 29-
Do PART 3: CLOSE AC-
CESS
-
Do PART 1: OPEN AC-
CESS
-CONDITION 2.2.2 (OPTION 1) (ACTION
3): Repeat the open hole HFEC inspection
of the fastener holes common to the under-
wing longeron fitting, upper drag splice
angle, and lower drag splice angle for any
crack.
-FIGURE 3
--CONDITION 2.2.2 (OPTION 2): Contact
The Boeing Company for any tension bolt
fastener stack-up repair, any front spar
lower chord repair, and any possible under-
wing longeron fitting hole repair instructions
and do the repair.
-FIGURE 35CONDITION 3 (ACTION 1): Do hole over-
size repair at the affected hole location(s),
through all fittings and angles in the joint.
(a)
CONDITION 3: ANY
CRACK FOUND ON
THE UPPER DRAG
SPLICE ANGLE OR
THE LOWER DRAG
SPLICE ANGLE
AND NO CRACK
FOUND ON THE
UNDERWING
LONGERON FIT-
TING.
-FIGURE 3CONDITION 3 (ACTION 2): Repeat the
open hole HFEC inspection at any hole(s).
(b)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 10, 2024
767-57A0148 RB
55 of 416
REQUIREMENTS BULLETIN 767-57A0148
ALERTALERT

### Page 56

Group 1, Configuration 1, 3:
Table 1: Left Side Underwing Longeron Fitting Forward Lower Fastener Holes Inspection
Refer to the listed pro-
cedures in SB 767-
57A0148 Original Issue
or later approved revi-
sions as an accepted
procedure
Method of Com-
pliance
ActionCondition
-FIGURE 33CONDITION 3.1 (ACTION 1): Install fasten-
ers.
CONDITION 3.1:
NO CRACK FOUND
AS A RESULT OF
CONDITION 3 (AC-
TION 2) INSPEC-
TION.
Do PART 3: CLOSE AC-
CESS
-
Do PART 1: OPEN AC-
CESS
-CONDITION 3.1 (ACTION 2): Repeat the
open hole HFEC inspection of the fastener
holes common to the underwing longeron
fitting, upper drag splice angle, and lower
drag splice angle for any crack.
-FIGURE 3
Do PART 2: DEFUEL
AIRPLANE
-Do an open hole HFEC inspection of the
entire fastener stack-up common to the
tension bolt hole and a surface HFEC in-
spection of the front spar lower chord for
any crack.
CONDITION 3.2:
ANY CRACK
FOUND THAT IS
MORE THAN THE
SECOND HOLE
OVERSIZE FROM
NOMINAL AS A
RESULT OF CONDI-
TION 3 (ACTION 2)
INSPECTION.
FIGURE 11-
-FIGURE 5
--Contact The Boeing Company for any up-
per drag splice angle repair and any lower
drag splice angle repair instructions and
do the repair.
CONDITION 3.2.1:
NO CRACK FOUND
AS A RESULT OF
CONDITION 3.2 IN-
SPECTION.
--Contact The Boeing Company for any up-
per drag splice angle repair, any lower drag
splice angle repair, any tension bolt fasten-
er stack-up repair, and any front spar lower
chord repair instructions and do the repair.
CONDITION 3.2.2:
ANY CRACK
FOUND AS A RE-
SULT OF CONDI-
TION 3.2 INSPEC-
TION.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 10, 2024
767-57A0148 RB
56 of 416
REQUIREMENTS BULLETIN 767-57A0148
ALERTALERT

### Page 57

Group 1, Configuration 1, 3:
Table 1: Left Side Underwing Longeron Fitting Forward Lower Fastener Holes Inspection
Refer to the listed pro-
cedures in SB 767-
57A0148 Original Issue
or later approved revi-
sions as an accepted
procedure
Method of Com-
pliance
ActionCondition
-FIGURE 35CONDITION 4 (ACTION 1): Do hole over-
size repair at the affected hole location(s),
through all fittings and angles in the joint.
(a)
CONDITION 4: ANY
CRACK FOUND ON
THE UNDERWING
LONGERON FIT-
TING AND ANY
CRACK FOUND ON
EITHER THE UP-
PER DRAG SPLICE
ANGLE OR THE
LOWER DRAG
SPLICE ANGLE.
CONDITION 4 (ACTION 2): At oversize
hole repair location(s), do an open hole
HFEC inspection of the fitting and angles
for any crack. (b)
-FIGURE 33CONDITION 4.1 (ACTION 1): Install fasten-
ers.
CONDITION 4.1:
NO CRACK FOUND
AS A RESULT OF
CONDITION 4 (AC-
TION 2) INSPEC-
TION.
Do PART 3: CLOSE AC-
CESS
-
Do PART 1: OPEN AC-
CESS
-CONDITION 4.1 (ACTION 2): Repeat the
open hole HFEC inspection of the fastener
holes common to the underwing longeron
fitting, upper drag splice angle, and lower
drag splice angle for any crack.
-FIGURE 3
Do PART 2: DEFUEL
AIRPLANE
-Do an open hole HFEC inspection of the
entire fastener stack-up common to the
tension bolt hole and a surface HFEC in-
spection of the front spar lower chord for
any crack.
CONDITION 4.2:
ANY CRACK
FOUND THAT IS
MORE THAN THE
SECOND HOLE
OVERSIZE FROM
NOMINAL AT A
FASTENER HOLE
ON THE UNDER-
WING LONGERON
FITTING ONLY, AS
A RESULT OF
CONDITION 4 (AC-
TION 2) INSPEC-
TION.
FIGURE 11-
-FIGURE 5
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 10, 2024
767-57A0148 RB
57 of 416
REQUIREMENTS BULLETIN 767-57A0148
ALERTALERT

### Page 58

Group 1, Configuration 1, 3:
Table 1: Left Side Underwing Longeron Fitting Forward Lower Fastener Holes Inspection
Refer to the listed pro-
cedures in SB 767-
57A0148 Original Issue
or later approved revi-
sions as an accepted
procedure
Method of Com-
pliance
ActionCondition
-FIGURE 15 P/N
111T4020U7
CONDITION 4.2.1 (OPTION 1) (ACTION
1): Replace the underwing longeron fitting
with new underwing longeron fitting.
CONDITION 4.2.1:
NO CRACK FOUND
AS A RESULT OF
CONDITION 4.2 IN-
SPECTION.
or
FIGURE 17 P/N
111T4020U13
FIGURE 29-
Do PART 3: CLOSE AC-
CESS
-
Do PART 1: OPEN AC-
CESS
-CONDITION 4.2.1 (OPTION 1) (ACTION
2): Repeat the open hole HFEC inspection
of the fastener holes common to the under-
wing longeron fitting, upper drag splice
angle, and lower drag splice angle for any
crack.
-FIGURE 3
--CONDITION 4.2.1 (OPTION 2): Contact
The Boeing Company for any possible un-
derwing longeron fitting hole repair instruc-
tions and do the repair.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 10, 2024
767-57A0148 RB
58 of 416
REQUIREMENTS BULLETIN 767-57A0148
ALERTALERT

### Page 59

Group 1, Configuration 1, 3:
Table 1: Left Side Underwing Longeron Fitting Forward Lower Fastener Holes Inspection
Refer to the listed pro-
cedures in SB 767-
57A0148 Original Issue
or later approved revi-
sions as an accepted
procedure
Method of Com-
pliance
ActionCondition
--CONDITION 4.2.2 (OPTION 1) (ACTION
1): Contact The Boeing Company for any
tension bolt fastener stack-up repair and
any front spar lower chord repair instruc-
tions and do the repair.
CONDITION 4.2.2:
ANY CRACK
FOUND AS A RE-
SULT OF CONDI-
TION 4.2 INSPEC-
TION. -FIGURE 15 P/N
111T4020U7
CONDITION 4.2.2 (OPTION 1) (ACTION
2): Replace the underwing longeron fitting
with new underwing longeron fitting. or
FIGURE 17 P/N
111T4020U13
FIGURE 29-
Do PART 3: CLOSE AC-
CESS
-
Do PART 1: OPEN AC-
CESS
-CONDITION 4.2.2 (OPTION 1) (ACTION
3): Repeat the open hole HFEC inspection
of the fastener holes common to the under-
wing longeron fitting, upper drag splice
angle, and lower drag splice angle for any
crack.
-FIGURE 3
--CONDITION 4.2.2 (OPTION 2): Contact
The Boeing Company for any tension bolt
fastener stack-up repair, any front spar
lower chord repair, and any possible under-
wing longeron fitting hole repair instructions
and do the repair.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 10, 2024
767-57A0148 RB
59 of 416
REQUIREMENTS BULLETIN 767-57A0148
ALERTALERT

### Page 60

Group 1, Configuration 1, 3:
Table 1: Left Side Underwing Longeron Fitting Forward Lower Fastener Holes Inspection
Refer to the listed pro-
cedures in SB 767-
57A0148 Original Issue
or later approved revi-
sions as an accepted
procedure
Method of Com-
pliance
ActionCondition
Do PART 2: DEFUEL
AIRPLANE
-Do an open hole HFEC inspection of the
entire fastener stack-up common to the
tension bolt hole and a surface HFEC in-
spection of the front spar lower chord for
any crack.
CONDITION 4.3:
ANY CRACK
FOUND THAT IS
MORE THAN THE
SECOND HOLE
OVERSIZE FROM
NOMINAL AT A
FASTENER HOLE
ON THE UPPER
DRAG SPLICE AN-
GLE OR THE LOW-
ER DRAG SPLICE
ANGLE BUT NO
CRACK FOUND ON
THE UNDERWING
LONGERON FIT-
TING, AS A RE-
SULT OF CONDI-
TION 4 (ACTION 2)
INSPECTION.
FIGURE 11-
-FIGURE 5
--Contact The Boeing Company for any up-
per drag splice angle repair and any lower
drag splice angle repair instructions and
do the repair.
CONDITION 4.3.1:
NO CRACK FOUND
AS A RESULT OF
CONDITION 4.3 IN-
SPECTION.
--Contact The Boeing Company for any up-
per drag splice angle repair, any lower drag
splice angle repair, any tension bolt fasten-
er stack-up repair, and any front spar lower
chord repair instructions and do the repair.
CONDITION 4.3.2:
ANY CRACK
FOUND AS A RE-
SULT OF CONDI-
TION 4.3 INSPEC-
TION.
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: October 10, 2024
767-57A0148 RB
60 of 416
REQUIREMENTS BULLETIN 767-57A0148
ALERTALERT

The text continues at https://openairdocs.org/service-documents/boeing/767-57a0148-rb/file/5a38c11d3702.md?from=61

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
