# Boeing Alert Requirements Bulletin 777-23A0454 RB: No revision named

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2026-0741, the docket of a proposed AD (Federal Register 2026-02420). Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Alert Requirements Bulletin 777-23A0454 RB](https://openairdocs.org/service-documents/boeing/777-23a0454-rb.md)
- Title as filed: 777-23A0454-00 RB
- Pages: 39
- PDF: https://openairdocs.org/files/sha256/a0/d3/a0d3bb42917930a5b572dca42b196cb4d2333ad446e70a101e023793eade1396
- Page: https://openairdocs.org/service-documents/boeing/777-23a0454-rb/file/a0d3bb429179

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Commercial 
Airplanes
777
Requirements Bulletin
ALERT
Number: 777-23A0454 RB
Original Issue: May 16, 2025
ATA System: 2315 5361
SUBJECT: COMMUNICATIONS - Satellite Communications (SATCOM) System - SATCOM High
Gain Antenna Adapter Plate Inspection and Change
EXPORT CONTROLLED - This technology or software is subject to the U.S. Export Administration Regulations
(EAR), (15 C.F.R. Parts 730-774). No authorization from the U.S. Department of Commerce is required for
export, re-export, in-country transfer, or access EXCEPT to country group E:1 or E:2 countries/persons per
Supp.1 to Part 740 of the EAR.
9E991ECCN:
BOEING PROPRIETARY
Copyright © 2025 The Boeing Company
Treatment of this document and its content is governed by contract with Boeing. Rights to use this document
are licensed on a per aircraft basis and such rights may not be transferable. For more information, contact The
Boeing Company.
Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner,
BBJ, DC-8, DC-9, DC-10, KC-10, KC-46, KDC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8, Poseidon and
Boeing liveries are all trademarks owned by The Boeing Company; and no trademark license is granted in
connection with this document unless provided in writing by Boeing.
Original Issue: May 16, 2025
777-23A0454 RB
1 of 39
3.0

### Page 2

Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: May 16, 2025
777-23A0454 RB
2 of 39
REQUIREMENTS BULLETIN 777-23A0454
ALERTALERT
BLANK PAGE

### Page 3

Table of Contents
1. EFFECTIVITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
A. Airplanes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
B. Spares Affected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2. CONCURRENT REQUIREMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3. COMPLIANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4. APPROVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
5. ACCOMPLISHMENT INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
A. General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
B. Work Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
FIGURE 1: SATELLITE COMMUNICATIONS (SATCOM) HIGH GAIN ANTENNA - ADAPTER PLATE,
PART NUMBER 100-602201-000 - DETAILED INSPECTION [Group 1, Configuration 2, 4] . 36
FIGURE 2: SATELLITE COMMUNICATIONS (SATCOM) HIGH GAIN ANTENNA - ADAPTER PLATE,
PART NUMBER 100-602547-000 - DETAILED INSPECTION [Group 1, Configuration 3-4] . 38
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: May 16, 2025
777-23A0454 RB
3 of 39
REQUIREMENTS BULLETIN 777-23A0454
ALERTALERT

### Page 4

Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: May 16, 2025
777-23A0454 RB
4 of 39
REQUIREMENTS BULLETIN 777-23A0454
ALERTALERT
BLANK PAGE

### Page 5

Commercial 
Airplanes
777
Requirements Bulletin
ALERT
Number: 777-23A0454 RB
Original Issue: May 16, 2025
ATA System: 2315 5361
SUBJECT: COMMUNICATIONS - Satellite Communications (SATCOM) System - SATCOM High
Gain Antenna Adapter Plate Inspection and Change
THIS DOCUMENT IS SENT TO THE OPERATORS OF RECORD OF THE AIRPLANES SHOWN IN
EFFECTIVITY. IF AN AIRPLANE HAS BEEN LEASED OR SOLD, SEND THIS DOCUMENT TO THE NEW
OPERATOR. IF APPLICABLE SPARES HAVE BEEN SOLD, SEND THIS DOCUMENT TO THE NEW OWNER.
THIS IS AN ENHANCED REQUIRED FOR COMPLIANCE DOCUMENT. THE BOEING PROCESSES USED
TO CREATE THE SERVICE BULLETIN (SB) AND THE REQUIREMENTS BULLETIN (RB) ENSURE THAT
THE INFORMATION BETWEEN "RC START" AND "RC END" IN THE SB ARE IDENTICAL TO THE
INFORMATION IN THE SAME SECTIONS (COMPLIANCE, WORK INSTRUCTIONS…) OF THE RB WHICH
THE SB REFERS TO AS THE RELATED DOCUMENT.
1. Effectivity
A. Airplanes
This bulletin is applicable to 777-200, 777-200LR, 777-300, 777-300ER Airplane(s), line number(s)
1-717, 719-731, 733-751, 753-759, 761-765, 767-769, 771-773, 775-779, 781, 783-787, 789-798,
800-810, 812, 814-819, 821-826, 828, 830-833, 835, 837, 839-843, 845, 847, 849-851, 853-855,
857-864, 866-868, 870-871, 873, 875, 877-880, 882-883, 885, 887, 889, 891, 893, 895-896,
898-903, 905-916, 918-935, 937-938, 940-941, 943-946, 948, 950-954, 956-959, 961-962, 964-966,
968-969, 971-972, 974, 976, 978-982, 984-988, 990-995, 997, 999-1001, 1003, 1005-1010,
1012-1014, 1016-1025, 1027-1032, 1034-1037, 1039-1040, 1042, 1044-1045, 1047, 1049,
1051-1053, 1055-1056, 1058-1059, 1061-1064, 1066-1071, 1073, 1075-1087, 1089-1099,
1101-1109, 1111-1119, 1121-1125, 1127-1133, 1135-1137, 1139-1143, 1145, 1147-1151,
1153-1155, 1157, 1159-1171, 1173-1177, 1179, 1181-1187, 1189-1191, 1193-1207, 1209, 1211,
1213-1229, 1231-1237, 1239-1241, 1243-1247, 1249-1251, 1253-1263, 1265-1267, 1269-1271,
1273, 1275-1277, 1279-1283, 1285-1305, 1307, 1309-1315, 1317, 1319, 1321-1325, 1327, 1329,
1331-1333, 1335, 1337-1341, 1343-1345, 1347-1353, 1355-1369, 1371-1373, 1375-1381,
1383-1391, 1393-1409, 1411-1429, 1431, 1433-1437, 1439, 1441-1446, 1448-1453, 1455-1472,
1474-1519, 1521, 1523, 1525, 1527, 1529-1530, 1533-1535, 1537-1545, 1547-1550, 1552-1556,
1558-1565, 1569, 1572, 1577, 1580, 1586, 1590, 1593, 1595, 1597-1598, 1600, 1602, 1607, 1609,
1613, 1618, 1627, 1630-1631, 1634-1637, 1639, 1641, 1643, 1648, 1652, 1654, 1667, 1671, 1675,
1678, 1681, 1683, 1686-1687, 1690-1691, 1695 in 1 Group(s). Where the effectivity is presented
with hyphens between line numbers, the airplane applicability means "through" and "inclusive",
e.g. line numbers 1-9 means line numbers 1 through 9 inclusive.
The Variable Numbers and Group Information for the applicable airplanes is given below.
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: May 16, 2025
777-23A0454 RB
5 of 39

### Page 6

DESCRIPTIONCONFIGURATIONGROUP
777-200/200LR/300/300ER airplanes that possibly have Satellite
Communications (SATCOM) High Gain Antenna Adapter Plate part
number 100-602201-000 or 100-602547-000 installed.
-1
Airplanes not equipped with SATCOM High Gain Antenna Adapter
Plate(s) part number 100-602201-000 or 100-602547-000.
1
Airplanes equipped with SATCOM High Gain Antenna Adapter
Plate(s) part number 100-602201-000 and not equipped with part
number 100-602547-000.
2
Airplanes equipped with SATCOM High Gain Antenna Adapter
Plate(s) part number 100-602547-000 and not equipped with part
number 100-602201-000.
3
Airplanes equipped with SATCOM High Gain Antenna Adapter Plate
part number 100-602201-000 and part number 100-602547-000.
4
Airplane Models:
777-200, 777-200LR, 777-300, 777-300ER
GroupVariable Number
1WA001 - WA017
1WA076 - WA080
1WA086 - WA093
1WA101 - WA104
1WA116 - WA119
1WA131 - WA137
1WA171 - WA175
1WA196 - WA198
1WA206 - WA212
1WA221 - WA223
1WA231 - WA232
1WA241 - WA250
1WA261 - WA266
1WA281 - WA283
1WA301 - WA304
1WB001 - WB021
GroupVariable Number
1WB031 - WB046
1WB051 - WB088
1WB101 - WB106
1WB121 - WB125
1WB131 - WB148
1WB151 - WB155
1WB161 - WB177
1WB181 - WB194
1WB201 - WB215
1WB231 - WB247
1WB271 - WB273
1WB276 - WB286
1WB291 - WB302
1WB306 - WB307
1WB311 - WB337
1WB341 - WB342
GroupVariable Number
1WB366 - WB368
1WB371 - WB388
1WB406
1WB411 - WB413
1WB416 - WB439
1WB446 - WB453
1WB476
1WB481 - WB484
1WB501 - WB512
1WB531 - WB537
1WB551 - WB554
1WB591 - WB597
1WB601 - WB606
1WB611 - WB622
1WB631 - WB638
1WB646 - WB649
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: May 16, 2025
777-23A0454 RB
6 of 39
REQUIREMENTS BULLETIN 777-23A0454
ALERTALERT

### Page 7

GroupVariable Number
1WC051 - WC073
1WC101 - WC104
1WC111 - WC120
1WC221 - WC224
1WC241 - WC243
1WC281 - WC290
1WC301 - WC308
1WC361 - WC364
1WC371 - WC374
1WC381 - WC395
1WC441
1WC446 - WC449
1WC456 - WC459
1WC486 - WC493
1WC506 - WC508
1WC521 - WC522
1WC531 - WC536
1WC546 - WC548
1WC556
1WC566 - WC567
1WC571 - WC574
1WC581
1WC586 - WC587
1WC591 - WC595
1WD001 - WD002
1WD011 - WD018
1WD031 - WD036
1WD046 - WD055
1WD066 - WD075
1WD081 - WD089
1WD091
1WD096
1WD101 - WD106
GroupVariable Number
1WD111 - WD112
1WD116 - WD117
1WD121 - WD123
1WD156
1WD501 - WD513
1WD521 - WD541
1WD546 - WD554
1WD561 - WD573
1WD581 - WD599
1WD606 - WD609
1WD621 - WD632
1WD651 - WD665
1WD671 - WD677
1WD691 - WD709
1WD741 - WD752
1WD761 - WD771
1WD786 - WD788
1WD796 - WD837
1WD846 - WD867
1WD871 - WD918
1WD921 - WD957
1WD966 - WD970
1WD981 - WD982
1WD986 - WD987
1WD991 - WD996
1WE001 - WE007
1WE011 - WE012
1WE021 - WE026
1WE031 - WE040
1WE051 - WE057
1WE071 - WE078
1WE081 - WE084
1WE091 - WE095
GroupVariable Number
1WE126 - WE178
1WE186 - WE219
1WE226 - WE231
1WE236 - WE253
1WE261 - WE267
1WE271 - WE278
1WE291 - WE298
1WE301 - WE320
1WE331 - WE356
1WE366 - WE368
1WE376 - WE377
1WE381
1WE386 - WE387
1WE391 - WE392
1WE396 - WE411
1WE416 - WE420
1WE426 - WE431
1WE436 - WE446
1WE451 - WE484
1WE486 - WE493
1WE495 - WE499
1WE501 - WE504
1WE511 - WE516
1WE526 - WE528
1WE536 - WE549
1WE556 - WE573
1WE576 - WE587
1WE591
1WE601 - WE605
1WE626 - WE627
1WE631
1WE641 - WE642
1WE646 - WE647
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: May 16, 2025
777-23A0454 RB
7 of 39
REQUIREMENTS BULLETIN 777-23A0454
ALERTALERT

### Page 8

GroupVariable Number
1WE651 - WE661
1WE666 - WE677
1WE681 - WE689
1WE701 - WE705
1WE711 - WE712
1WE731 - WE732
1WE736 - WE740
GroupVariable Number
1WE746 - WE772
1WE776 - WE786
1WE791 - WE792
1WE796 - WE798
1WE801 - WE806
1WE811 - WE812
1WE826 - WE828
GroupVariable Number
1WE831 - WE835
1WE851 - WE853
1WE856 - WE857
1WE861 - WE863
1WE866 - WE868
1WE871
--
B. Spares Affected
None.
2. CONCURRENT REQUIREMENTS
None.
3. COMPLIANCE
The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to
Requirements Bulletin 777-23A0454 RB. The Airworthiness Directive will make the compliance tasks and
times given in Requirements Bulletin 777-23A0454 RB mandatory.
Accomplish the required action(s), based on the applicable condition(s) in Table 1 through Table 4, in
accordance with Accomplishment Instructions.
When more than one OPTION is given for a CONDITION, do only one of the OPTION numbers. When
more than one ACTION is given for a CONDITION or an OPTION, do all of the ACTION numbers for that
CONDITION or OPTION.
Group 1, Configuration 1:
No work is necessary.
Subsequent to the Original Issue date of Requirements Bulletin 777-23A0454 RB, any airplane that installs
SATCOM High Gain Antenna Adapter Plate part number 100-602201-000 and not with part number
100-602547-000 must comply with the requirements specified in Group 1, Configuration 2.
Subsequent to the Original Issue date of Requirements Bulletin 777-23A0454 RB, any airplane that installs
SATCOM High Gain Antenna Adapter Plate part number 100-602547-000 and not with part number
100-602201-000 must comply with the requirements specified in Group 1, Configuration 3.
Subsequent to the Original Issue date of Requirements Bulletin 777-23A0454 RB, any airplane that installs
SATCOM High Gain Antenna Adapter Plate part number 100-602201-000 and part number 100-602547-000
must comply with the requirements specified in Group 1, Configuration 4.
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: May 16, 2025
777-23A0454 RB
8 of 39
REQUIREMENTS BULLETIN 777-23A0454
ALERTALERT

### Page 9

Group 1, Configuration 2, 4:
Table 1: Satellite Communications (SATCOM) High Gain Antenna Adapter Plate Inspection
Repeat Interval
(Not to Exceed)
Boeing Recommended
Compliance Time
ActionCondition
-Within 12 months after
the Original Issue date of
Requirements Bulletin
777-23A0454 RB.
At the location(s) where part number 100-
602201-000 is installed, do a Detailed
Inspection (DET) of the SATCOM High
Gain Antenna Adapter Plate for corrosion.
Airplanes with SAT-
COM High Gain Anten-
na Adapter Plate(s)
with part number 100-
602201-000 that have
been installed for 20
years or more as of the
Original Issue date of
Requirements Bulletin
777-23A0454 RB, or
the installation date
cannot be determined.
(d)
1200 days.-At the location(s) where part number 100-
602201-000 is installed, repeat the DET
of the SATCOM High Gain Antenna
Adapter Plate for corrosion. (c)
CONDITION 1: NO
CORROSION FOUND
-Before further flight.OPTION 1 (ACTION 1): Repair the SAT-
COM High Gain Antenna Adapter Plate.
CONDITION 2: ANY
CORROSION FOUND
WITHIN REPAIR LIM-
ITS (a) 1200 days.-OPTION 1 (ACTION 2): At the location(s)where part number 100-602201-000 is
installed, repeat the DET of the SATCOM
High Gain Antenna Adapter Plate for
corrosion. (c)
-Before further flight.OPTION 2 (ACTION 1): Replace the
SATCOM High Gain Antenna Adapter
Plate with a serviceable SATCOM High
Gain Antenna Adapter Plate. (b)
1200 days.-OPTION 2 (ACTION 2): At the location(s)
where part number 100-602201-000 is
installed, repeat the DET of the SATCOM
High Gain Antenna Adapter Plate for
corrosion. (c)
-Before further flight.OPTION 3 (ACTION 1): Replace the
SATCOM High Gain Antenna Adapter
Plate with a new SATCOM High Gain
Antenna Adapter Plate.
3600 days.-OPTION 3 (ACTION 2): At the location(s)
where part number 100-602201-000 is
installed, repeat the DET of the SATCOM
High Gain Antenna Adapter Plate for
corrosion. (c)
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: May 16, 2025
777-23A0454 RB
9 of 39
REQUIREMENTS BULLETIN 777-23A0454
ALERTALERT

### Page 10

Group 1, Configuration 2, 4:
Table 1: Satellite Communications (SATCOM) High Gain Antenna Adapter Plate Inspection
Repeat Interval
(Not to Exceed)
Boeing Recommended
Compliance Time
ActionCondition
-Before further flight.OPTION 1 (ACTION 1): Replace the
SATCOM High Gain Antenna Adapter
plate with a serviceable SATCOM High
Gain Antenna Adapter Plate. (b)
CONDITION 3: ANY
CORROSION FOUND
BEYOND THE REPAIR
LIMITS (a)
1200 days.-OPTION 1 (ACTION 2): At the location(s)
where part number 100-602201-000 is
installed, repeat the DET of the SATCOM
High Gain Antenna Adapter Plate for
corrosion. (c)
-Before further flight.OPTION 2 (ACTION 1): Replace the
SATCOM High Gain Antenna Adapter
Plate with a new SATCOM High Gain
Antenna Adapter Plate.
3600 days.-OPTION 2 (ACTION 2): At the location(s)
where part number 100-602201-000 is
installed, repeat the DET of the SATCOM
High Gain Antenna Adapter Plate for
corrosion. (c)
(a) Any corrosion equal to or less than 0.005 inch into the SATCOM High Gain Antenna Adapter plate is
within repair limits. SATCOM High Gain Antenna Adapter plate repair limits can be found in CMC Electronics
CMM 23-15-06, Original Issue, dated April 16, 2024, or later revisions.
(b) A serviceable SATCOM High Gain Antenna Adapter Plate is one that has been inspected for corrosion
and applicable on-condition corrective actions have been done in accordance with Requirements Bulletin
777-23A0454 RB.
(c) The removal of SATCOM High Gain Antenna Adapter Plate part number 100-602201-000 after the Original
Issue date of Requirements Bulletin 777-23A0454 RB terminates the repeat DET inspection at the location(s)
where part number 100-602201-000 was installed.
(d) Some High Gain Antenna Adapter Plate(s) with part number 100-602201-000 may have been modified
to 100-602201-000-777-53A0070 per SB 777-53A0070. The condition(s) and accomplishment of the re-
quired action(s) in accordance with Requirements Bulletin 777-23A0454 RB are also applicable to part
number 100-602201-000-777-53A0070.
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: May 16, 2025
777-23A0454 RB
10 of 39
REQUIREMENTS BULLETIN 777-23A0454
ALERTALERT

### Page 11

Group 1, Configuration 2, 4:
Table 2: Satellite Communications (SATCOM) High Gain Antenna Adapter Plate Inspection
Repeat Interval
(Not to Exceed)
Boeing Recommended
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Within 3600
days after in-
stallation of a
new SATCOM
High Gain An-
tenna Adapter
Plate.
Within 24
months after
the Original Is-
sue date of Re-
quirements
Bulletin 777-
23A0454 RB.
At the location(s) where part num-
ber 100-602201-000 is installed,
do a Detailed Inspection (DET) of
the SATCOM High Gain Antenna
Adapter Plate for corrosion.
Airplanes with SAT-
COM High Gain Anten-
na Adapter Plate(s)
with part number 100-
602201-000 that have
been installed for less
than 20 years as of the
Original Issue date of
Requirements Bulletin
777-23A0454 RB. (d)
1200 days.-At the location(s) where part num-
ber 100-602201-000 is installed,
repeat the DET of the SATCOM
High Gain Antenna Adapter Plate
for corrosion. (c)
CONDITION 4: NO
CORROSION FOUND
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: May 16, 2025
777-23A0454 RB
11 of 39
REQUIREMENTS BULLETIN 777-23A0454
ALERTALERT

### Page 12

Group 1, Configuration 2, 4:
Table 2: Satellite Communications (SATCOM) High Gain Antenna Adapter Plate Inspection
Repeat Interval
(Not to Exceed)
Boeing Recommended
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flight.OPTION 1 (ACTION 1): Repair the
SATCOM High Gain Antenna
Adapter Plate.
CONDITION 5: ANY
CORROSION FOUND
WITHIN REPAIR LIM-
ITS (a) 1200 days.-OPTION 1 (ACTION 2): At the lo-
cation(s) where part number 100-
602201-000 is installed, repeat the
DET of the SATCOM High Gain
Antenna Adapter Plate for corro-
sion. (c)
-Before further flight.OPTION 2 (ACTION 1): Replace
the SATCOM High Gain Antenna
Adapter plate with a serviceable
SATCOM High Gain Antenna
Adapter Plate. (b)
1200 days.-OPTION 2 (ACTION 2): At the lo-
cation(s) where part number 100-
602201-000 is installed, repeat the
DET of the SATCOM High Gain
Antenna Adapter Plate for corro-
sion. (c)
-Before further flight.OPTION 3 (ACTION 1): Replace
the SATCOM High Gain Antenna
Adapter Plate with a new SATCOM
High Gain Antenna Adapter Plate.
3600 days.-OPTION 3 (ACTION 2): At the lo-
cation(s) where part number 100-
602201-000 is installed, repeat the
DET of the SATCOM High Gain
Antenna Adapter Plate for corro-
sion. (c)
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: May 16, 2025
777-23A0454 RB
12 of 39
REQUIREMENTS BULLETIN 777-23A0454
ALERTALERT

### Page 13

Group 1, Configuration 2, 4:
Table 2: Satellite Communications (SATCOM) High Gain Antenna Adapter Plate Inspection
Repeat Interval
(Not to Exceed)
Boeing Recommended
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flight.OPTION 1 (ACTION 1): Replace
the SATCOM High Gain Antenna
Adapter Plate with a serviceable
SATCOM High Gain Antenna
Adapter Plate. (b)
CONDITION 6: ANY
CORROSION FOUND
BEYOND THE REPAIR
LIMITS (a)
1200 days.-OPTION 1 (ACTION 2): At the lo-
cation(s) where part number 100-
602201-000 is installed, repeat the
DET of the SATCOM High Gain
Antenna Adapter Plate for corro-
sion. (c)
-Before further flight.OPTION 2 (ACTION 1): Replace
the SATCOM High Gain Antenna
Adapter plate with a new SATCOM
High Gain Antenna Adapter Plate.
3600 days.-OPTION 2 (ACTION 2): At the lo-
cation(s) where part number 100-
602201-000 is installed, repeat the
DET of the SATCOM High Gain
Antenna Adapter Plate for corro-
sion. (c)
(a) Any corrosion equal to or less than 0.005 inch into the SATCOM High Gain Antenna Adapter plate is
within repair limits. SATCOM High Gain Antenna Adapter plate repair limits can be found in CMC Electronics
CMM 23-15-06, Original Issue, dated April 16, 2024, or later revisions.
(b) A serviceable SATCOM High Gain Antenna Adapter Plate is one that has been inspected for corrosion
and applicable on-condition corrective actions have been done in accordance with Requirements Bulletin
777-23A0454 RB.
(c) The removal of SATCOM High Gain Antenna Adapter Plate part number 100-602201-000 after the Original
Issue date of Requirements Bulletin 777-23A0454 RB terminates the repeat DET inspection at the location(s)
where part number 100-602201-000 was installed.
(d) Some High Gain Antenna Adapter Plate(s) with part number 100-602201-000 may have been modified
to 100-602201-000-777-53A0070 per SB 777-53A0070. The condition(s) and accomplishment of the re-
quired action(s) in accordance with Requirements Bulletin 777-23A0454 RB are also applicable to part
number 100-602201-000-777-53A0070.
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: May 16, 2025
777-23A0454 RB
13 of 39
REQUIREMENTS BULLETIN 777-23A0454
ALERTALERT

### Page 14

Group 1, Configuration 3-4:
Table 3: Satellite Communications (SATCOM) High Gain Antenna Adapter Plate Inspection
Repeat Interval
(Not to Exceed)
Boeing Recommended
Compliance Time
ActionCondition
-Within 12 months after
the Original Issue date of
Requirements Bulletin
777-23A0454 RB.
At the location(s) where part number 100-
602547-000 is installed, do a Detailed
Inspection (DET) of the SATCOM High
Gain Antenna Adapter Plate for corrosion.
Airplanes with SAT-
COM High Gain Anten-
na Adapter Plate(s)
with part number 100-
602547-000 that have
been installed for 20
years or more as of the
Original Issue date of
Requirements Bulletin
777-23A0454 RB, or
the installation date
cannot be determined.
(d)
1200 days.-At the location(s) where part number 100-
602547-000 is installed, repeat the DET
of the SATCOM High Gain Antenna
Adapter Plate for corrosion. (c)
CONDITION 7: NO
CORROSION FOUND
-Before further flight.OPTION 1 (ACTION 1): Repair the SAT-
COM High Gain Antenna Adapter Plate.
CONDITION 8: ANY
CORROSION FOUND
WITHIN REPAIR LIM-
ITS (a) 1200 days.-OPTION 1 (ACTION 2): At the location(s)where part number 100-602547-000 is
installed, repeat the DET of the SATCOM
High Gain Antenna Adapter Plate for
corrosion. (c)
-Before further flight.OPTION 2 (ACTION 1): Replace the
SATCOM High Gain Antenna Adapter
Plate with a serviceable SATCOM High
Gain Antenna Adapter Plate. (b)
1200 days.-OPTION 2 (ACTION 2): At the location(s)
where part number 100-602547-000 is
installed, repeat the DET of the SATCOM
High Gain Antenna Adapter Plate for
corrosion. (c)
-Before further flight.OPTION 3 (ACTION 1): Replace the
SATCOM High Gain Antenna Adapter
Plate with a new SATCOM High Gain
Antenna Adapter Plate.
3600 days.-OPTION 3 (ACTION 2): At the location(s)
where part number 100-602547-000 is
installed, repeat the DET of the SATCOM
High Gain Antenna Adapter Plate for
corrosion. (c)
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: May 16, 2025
777-23A0454 RB
14 of 39
REQUIREMENTS BULLETIN 777-23A0454
ALERTALERT

### Page 15

Group 1, Configuration 3-4:
Table 3: Satellite Communications (SATCOM) High Gain Antenna Adapter Plate Inspection
Repeat Interval
(Not to Exceed)
Boeing Recommended
Compliance Time
ActionCondition
-Before further flight.OPTION 1 (ACTION 1): Replace the
SATCOM High Gain Antenna Adapter
plate with a serviceable SATCOM High
Gain Antenna Adapter Plate. (b)
CONDITION 9: ANY
CORROSION FOUND
BEYOND THE REPAIR
LIMITS (a)
1200 days.-OPTION 1 (ACTION 2): At the location(s)
where part number 100-602547-000 is
installed, repeat the DET of the SATCOM
High Gain Antenna Adapter Plate for
corrosion. (c)
-Before further flight.OPTION 2 (ACTION 1): Replace the
SATCOM High Gain Antenna Adapter
Plate with a new SATCOM High Gain
Antenna Adapter Plate.
3600 days.-OPTION 2 (ACTION 2): At the location(s)
where part number 100-602547-000 is
installed, repeat the DET of the SATCOM
High Gain Antenna Adapter Plate for
corrosion. (c)
(a) Any corrosion equal to or less than 0.005 inch into the SATCOM High Gain Antenna Adapter plate is
within repair limits. SATCOM High Gain Antenna Adapter plate repair limits can be found in CMC Electronics
CMM 23-15-06, Original Issue, dated April 16, 2024, or later revisions.
(b) A serviceable SATCOM High Gain Antenna Adapter Plate is one that has been inspected for corrosion
and applicable on-condition corrective actions have been done in accordance with Requirements Bulletin
777-23A0454 RB.
(c) The removal of SATCOM High Gain Antenna Adapter Plate part number 100-602547-000 after the Original
Issue date of Requirements Bulletin 777-23A0454 RB terminates the repeat DET inspection at the location(s)
where part number 100-602547-000 was installed.
(d) Some High Gain Antenna Adapter Plate(s) with part number 100-602547-000 may have been modified
to 100-602547-000-777-53A0070 per SB 777-53A0070. The condition(s) and accomplishment of the re-
quired action(s) in accordance with Requirements Bulletin 777-23A0454 RB are also applicable to part
number 100-602547-000-777-53A0070.
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: May 16, 2025
777-23A0454 RB
15 of 39
REQUIREMENTS BULLETIN 777-23A0454
ALERTALERT

### Page 16

Group 1, Configuration 3-4:
Table 4: Satellite Communications (SATCOM) High Gain Antenna Adapter Plate Inspection
Repeat Interval
(Not to Exceed)
Boeing Recommended
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Within 3600
days after in-
stallation of a
new SATCOM
High Gain An-
tenna Adapter
plate.
Within 24
months after
the Original Is-
sue date of Re-
quirements
Bulletin 777-
23A0454 RB.
At the location(s) where part num-
ber 100-602547-000 is installed,
do a detailed inspection (DET) of
the SATCOM High Gain Antenna
Adapter Plate for corrosion.
Airplanes with SAT-
COM High Gain Anten-
na Adapter Plate(s)
with part number 100-
602547-000 that have
been installed for less
than 20 years as of the
Original Issue date of
Requirements Bulletin
777-23A0454 RB. (d)
1200 days.-At the location(s) where part num-
ber 100-602547-000 is installed,
repeat the DET of the SATCOM
High Gain Antenna Adapter Plate
for corrosion.(c)
CONDITION 10: NO
CORROSION FOUND
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: May 16, 2025
777-23A0454 RB
16 of 39
REQUIREMENTS BULLETIN 777-23A0454
ALERTALERT

### Page 17

Group 1, Configuration 3-4:
Table 4: Satellite Communications (SATCOM) High Gain Antenna Adapter Plate Inspection
Repeat Interval
(Not to Exceed)
Boeing Recommended
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flight.OPTION 1 (ACTION 1): Repair the
SATCOM High Gain Antenna
Adapter Plate.
CONDITION 11: ANY
CORROSION FOUND
WITHIN REPAIR LIM-
ITS (a) 1200 days.-OPTION 1 (ACTION 2): At the lo-
cation(s) where part number 100-
602547-000 is installed, repeat the
DET of the SATCOM High Gain
Antenna Adapter Plate for corro-
sion. (c)
-Before further flight.OPTION 2 (ACTION 1): Replace
the SATCOM High Gain Antenna
Adapter plate with a serviceable
SATCOM High Gain Antenna
Adapter Plate. (b)
1200 days.-OPTION 2 (ACTION 2): At the lo-
cation(s) where part number 100-
602547-000 is installed, repeat the
DET of the SATCOM High Gain
Antenna Adapter Plate for corro-
sion. (c)
-Before further flight.OPTION 3 (ACTION 1): Replace
the SATCOM High Gain Antenna
Adapter Plate with a new SATCOM
High Gain Antenna Adapter Plate.
3600 days.-OPTION 3 (ACTION 2): At the lo-
cation(s) where part number 100-
602547-000 is installed, repeat the
DET of the SATCOM High Gain
Antenna Adapter Plate for corro-
sion. (c)
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: May 16, 2025
777-23A0454 RB
17 of 39
REQUIREMENTS BULLETIN 777-23A0454
ALERTALERT

### Page 18

Group 1, Configuration 3-4:
Table 4: Satellite Communications (SATCOM) High Gain Antenna Adapter Plate Inspection
Repeat Interval
(Not to Exceed)
Boeing Recommended
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flight.OPTION 1 (ACTION 1): Replace
the SATCOM High Gain Antenna
Adapter Plate with a serviceable
SATCOM High Gain Antenna
Adapter Plate. (b)
CONDITION 12: ANY
CORROSION FOUND
BEYOND THE REPAIR
LIMITS (a)
1200 days.-OPTION 1 (ACTION 2): At the lo-
cation(s) where part number 100-
602547-000 is installed, repeat the
DET of the SATCOM High Gain
Antenna Adapter Plate for corro-
sion. (c)
-Before further flight.OPTION 2 (ACTION 1): Replace
the SATCOM High Gain Antenna
Adapter Plate with a new SATCOM
High Gain Antenna Adapter Plate.
3600 days.-OPTION 2 (ACTION 2): At the lo-
cation(s) where part number 100-
602547-000 is installed, repeat the
DET of the SATCOM High Gain
Antenna Adapter Plate for corro-
sion. (c)
(a) Any corrosion equal to or less than 0.005 inch into the SATCOM High Gain Antenna Adapter plate is
within repair limits. SATCOM High Gain Antenna Adapter plate repair limits can be found in CMC Electronics
CMM 23-15-06, Original Issue, dated April 16, 2024, or later revisions.
(b) A serviceable SATCOM High Gain Antenna Adapter Plate is one that has been inspected for corrosion
and applicable on-condition corrective actions have been done in accordance with Requirements Bulletin
777-23A0454 RB.
(c) The removal of SATCOM High Gain Antenna Adapter Plate part number 100-602547-000 after the Original
Issue date of Requirements Bulletin 777-23A0454 RB terminates the repeat DET inspection at the location(s)
where part number 100-602547-000 was installed.
(d) Some High Gain Antenna Adapter Plate(s) with part number 100-602547-000 may have been modified
to 100-602547-000-777-53A0070 per SB 777-53A0070. The condition(s) and accomplishment of the re-
quired action(s) in accordance with Requirements Bulletin 777-23A0454 RB are also applicable to part
number 100-602547-000-777-53A0070.
4. APPROVAL
This Requirements Bulletin was examined by the Federal Aviation Administration (FAA). The changes
specified in this document comply with the applicable regulations and are FAA approved, as well as European
Union Aviation Safety Agency (EASA) approved for all EASA approved airplanes listed in this Requirements
Bulletin effectivity. This document and its approval were based on the airplane in its original Boeing delivery
configuration or as modified by other Boeing changes.
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: May 16, 2025
777-23A0454 RB
18 of 39
REQUIREMENTS BULLETIN 777-23A0454
ALERTALERT

### Page 19

If an airplane has a non-Boeing modification or repair that affects a component or system also affected by
this Requirements Bulletin, the operator is responsible for obtaining appropriate regulatory agency approval
before incorporating this Requirements Bulletin.
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: May 16, 2025
777-23A0454 RB
19 of 39
REQUIREMENTS BULLETIN 777-23A0454
ALERTALERT

### Page 20

Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: May 16, 2025
777-23A0454 RB
20 of 39
REQUIREMENTS BULLETIN 777-23A0454
ALERTALERT
BLANK PAGE

### Page 21

5.    ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL INFORMATION
NOTE: 1. This is an Enhanced Required for Compliance document. There will be a separate
Service Bulletin (SB) and a separate Requirements Bulletin (RB). If an RB is mandated
by an Airworthiness Directive (AD), then all applicable requirements specified in the
RB must be done. In the RB, the "Refer to the listed procedures..." column of the
table(s) in the Work Instructions is for reference only. The procedures in that column
are not required by the AD and are for guidance only. For the related SB, some
locations are marked RC Start and RC End to identify the requirements that are
restated from the RB. For the related SB, the areas between RC Start and RC End,
including sub-steps and any figures identified between RC Start and RC End, must
be done to comply with the AD. Therefore, an Alternative Method of Compliance
(AMOC) is required for any deviations to steps between RC Start and RC End,
including substeps and identified figures. For the related SB, the steps not between
RC Start and RC End may be deviated from using accepted methods in accordance
with the operator's maintenance or inspection program without obtaining approval
of an AMOC; this is provided that the steps between RC Start and RC End, including
sub-steps and identified figures, can still be done as specified, and the airplane can
be put back in an airworthy condition. Figures not required for compliance are omitted
from the RB.
2. This is an Enhanced Required for Compliance document. The Boeing processes
used to create the Service Bulletin (SB) and the Requirements Bulletin (RB) ensure
that the information between "RC Start" and "RC End" in the SB are identical to the
information in the same sections (Compliance, Work Instructions...) of the RB which
the SB refers to as the related document.
3. The compliance times for the actions in WORK INSTRUCTIONS are in Compliance.
4. Unless shown differently, these dimensions and tolerances are used:
– Linear dimensions are in inches
– Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus
or minus 0.03 inch
– Tolerance on rivet and bolt edge margin is plus or minus 0.05 inch
– Angular tolerance is plus or minus 2 degrees
– Hole dimensions for standard solid rivets and fasteners are in Structural Repair
Manual (SRM) Chapter 51
– Torque Values:
— Values for structural fasteners are given in 777 Structural Repair Manual,
Chapter 51.
— Values for airframe maintenance tasks are included in Chapter 20 of 777
Aircraft Maintenance Manual (AMM).
— Values for electrical maintenance tasks are included in Chapter 20 of
Standard Wiring Practices Manual (SWPM).
— Values for engine maintenance tasks are included in Chapter 70 of 777
Aircraft Maintenance Manual (AMM).
— Non-standard torque values for maintenance tasks are included in the
applicable installation step.
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: May 16, 2025
777-23A0454 RB
21 of 39
REQUIREMENTS BULLETIN 777-23A0454
ALERTALERT

### Page 22

5. These work instructions refer to procedures included in other Boeing documents.
When the words "refer to" are used and the operator has an accepted alternative
procedure, the accepted alternative procedure can be used. When the words "in
accordance with" are included in the instruction, the procedure in the Boeing document
must be used.
6. Where the work instructions include installation of a kept part, a new or serviceable
part with the same part number can be installed as an alternative to the kept part.
7. If it is necessary to remove more parts for access, you can remove those parts. If
you can get access without removing identified parts, it is not necessary to remove
all of the identified parts. Jacking and shoring limitations must be observed.
8. Use the approved fastener, process and material substitutions in accordance with
SRM Chapter 51.
9. A Detailed Inspection (DET) is defined as: An intensive examination of a specific
item, installation or assembly to detect damage, failure or irregularity. This could
include tactile assessment in which a component or assembly can be checked for
tightness/security. Available lighting is normally supplemented with a direct source
of good lighting at an intensity deemed appropriate. Inspection aids such as mirrors
and magnifying lenses may be necessary. Surface cleaning and elaborate access
procedures may be required.
10. When more than one OPTION is given for a CONDITION, do only one of the OPTION
numbers. When more than one ACTION is given for a CONDITION or an OPTION,
do all of the ACTION numbers for that CONDITION or OPTION.
11. Use of colors in Figures is based on guidance from the ATA e-Business Program
(ATA) iSpec 2200.
B. WORK INSTRUCTIONS
Actions Required for Compliance
1. Requirements:
Group 1, Configuration 1:
No work is necessary.
Subsequent to the Original Issue date of Requirements Bulletin 777-23A0454 RB, any airplane
that installs SATCOM High Gain Antenna Adapter Plate part number 100-602201-000 and not
with part number 100-602547-000 must comply with the requirements specified in Group 1,
Configuration 2.
Subsequent to the Original Issue date of Requirements Bulletin 777-23A0454 RB, any airplane
that installs SATCOM High Gain Antenna Adapter Plate part number 100-602547-000 and not
with part number 100-602201-000 must comply with the requirements specified in Group 1,
Configuration 3.
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: May 16, 2025
777-23A0454 RB
22 of 39
REQUIREMENTS BULLETIN 777-23A0454
ALERTALERT

### Page 23

Subsequent to the Original Issue date of Requirements Bulletin 777-23A0454 RB, any airplane
that installs SATCOM High Gain Antenna Adapter Plate part number 100-602201-000 and part
number 100-602547-000 must comply with the requirements specified in Group 1, Configuration
4.
Group 1, Configuration 2, 4:
Table 1: Satellite Communications (SATCOM) High Gain Antenna Adapter Plate Inspection
Refer to the listed
procedures in SB
777-23A0454 Origi-
nal Issue or later
approved revi-
sions as an accept-
ed procedure.
Method of
Compliance
ActionCondition
Do PART 1: SAT-
COM HIGH GAIN
ANTENNA
ADAPTER PLATE
REMOVAL
-At the location(s) where part number 100-
602201-000 is installed, do a Detailed
Inspection (DET) of the SATCOM High
Gain Antenna Adapter Plate for corrosion.
Airplanes with SATCOM High
Gain Antenna Adapter Plate(s)
with part number 100-602201-
000 that have been installed for
20 years or more as of the
Original Issue date of Require-
ments Bulletin 777-23A0454
RB, or the installation date can-
not be determined. (d)
-FIGURE 1
Do PART 2: SAT-
COM HIGH GAIN
ANTENNA
ADAPTER PLATE
INSTALLATION
-At the location(s) where part number 100-
602201-000 is installed, repeat the DET
of the SATCOM High Gain Antenna
Adapter Plate for corrosion. (c)
CONDITION 1: NO CORRO-
SION FOUND
Do PART 4: CLOSE
ACCESS
-
-FIGURE 1
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: May 16, 2025
777-23A0454 RB
23 of 39
REQUIREMENTS BULLETIN 777-23A0454
ALERTALERT

### Page 24

Group 1, Configuration 2, 4:
Table 1: Satellite Communications (SATCOM) High Gain Antenna Adapter Plate Inspection
Refer to the listed
procedures in SB
777-23A0454 Origi-
nal Issue or later
approved revi-
sions as an accept-
ed procedure.
Method of
Compliance
ActionCondition
CMC Electronics
CMM 23-15-06
Original Issue, dat-
ed April 16, 2024, or
later revisions.
-OPTION 1 (ACTION 1): Repair the SAT-
COM High Gain Antenna Adapter Plate.
CONDITION 2: ANY CORRO-
SION FOUND WITHIN REPAIR
LIMITS (a)
Do PART 2: SAT-
COM HIGH GAIN
ANTENNA
ADAPTER PLATE
INSTALLATION
-
Do PART 4: CLOSE
ACCESS
-
-FIGURE 1OPTION 1 (ACTION 2): At the location(s)
where part number 100-602201-000 is
installed, repeat the DET of the SATCOM
High Gain Antenna Adapter Plate for
corrosion. (c)
Do PART 3: SAT-
COM HIGH GAIN
ANTENNA
ADAPTER PLATE
REPLACEMENT
-OPTION 2 (ACTION 1): Replace the
SATCOM High Gain Antenna Adapter
Plate with a serviceable SATCOM High
Gain Antenna Adapter Plate. (b)
Do PART 4: CLOSE
ACCESS
-
-FIGURE 1OPTION 2 (ACTION 2): At the location(s)
where part number 100-602201-000 is
installed, repeat the DET of the SATCOM
High Gain Antenna Adapter Plate for
corrosion. (c)
Do PART 3: SAT-
COM HIGH GAIN
ANTENNA
ADAPTER PLATE
REPLACEMENT
-OPTION 3 (ACTION 1): Replace the
SATCOM High Gain Antenna Adapter
plate with a new SATCOM High Gain
Antenna Adapter Plate.
Do PART 4: CLOSE
ACCESS
-
-FIGURE 1
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: May 16, 2025
777-23A0454 RB
24 of 39
REQUIREMENTS BULLETIN 777-23A0454
ALERTALERT

### Page 25

Group 1, Configuration 2, 4:
Table 1: Satellite Communications (SATCOM) High Gain Antenna Adapter Plate Inspection
Refer to the listed
procedures in SB
777-23A0454 Origi-
nal Issue or later
approved revi-
sions as an accept-
ed procedure.
Method of
Compliance
ActionCondition
OPTION 3 (ACTION 2): At the location(s)
where part number 100-602201-000 is
installed, repeat the DET of the SATCOM
High Gain Antenna Adapter Plate for
corrosion. (c)
Do PART 3: SAT-
COM HIGH GAIN
ANTENNA
ADAPTER PLATE
REPLACEMENT
-OPTION 1 (ACTION 1): Replace the
SATCOM High Gain Antenna Adapter
Plate with a serviceable SATCOM High
Gain Antenna Adapter Plate. (b)
CONDITION 3: ANY CORRO-
SION FOUND BEYOND THE
REPAIR LIMITS (a)
Do PART 4: CLOSE
ACCESS
-
-FIGURE 1OPTION 1 (ACTION 2): At the location(s)
where part number 100-602201-000 is
installed, repeat the DET of the SATCOM
High Gain Antenna Adapter Plate for
corrosion. (c)
Do PART 3: SAT-
COM HIGH GAIN
ANTENNA
ADAPTER PLATE
REPLACEMENT
-OPTION 2 (ACTION 1): Replace the
SATCOM High Gain Antenna Adapter
Plate with a new SATCOM High Gain
Antenna Adapter Plate.
Do PART 4: CLOSE
ACCESS
-
-FIGURE 1OPTION 2 (ACTION 2): At the location(s)
where part number 100-602201-000 is
installed, repeat the DET of the SATCOM
High Gain Antenna Adapter Plate for
corrosion. (c)
(a) Any corrosion equal to or less than 0.005 inch into the SATCOM High Gain Antenna Adapter plate is
within repair limits. SATCOM High Gain Antenna Adapter plate repair limits can be found in CMC Electronics
CMM 23-15-06, Original Issue, dated April 16, 2024, or later revisions.
(b) A serviceable SATCOM High Gain Antenna Adapter Plate is one that has been inspected for corrosion
and applicable on-condition corrective actions have been done in accordance with Requirements Bulletin
777-23A0454 RB.
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: May 16, 2025
777-23A0454 RB
25 of 39
REQUIREMENTS BULLETIN 777-23A0454
ALERTALERT

### Page 26

Group 1, Configuration 2, 4:
Table 1: Satellite Communications (SATCOM) High Gain Antenna Adapter Plate Inspection
Refer to the listed
procedures in SB
777-23A0454 Origi-
nal Issue or later
approved revi-
sions as an accept-
ed procedure.
Method of
Compliance
ActionCondition
(c) The removal of SATCOM High Gain Antenna Adapter Plate part number 100-602201-000 after the Original
Issue date of Requirements Bulletin 777-23A0454 RB terminates the repeat DET inspection at the location(s)
where part number 100-602201-000 was installed.
(d) Some High Gain Antenna Adapter Plate(s) with part number 100-602201-000 may have been modified
to 100-602201-000-777-53A0070 per SB 777-53A0070. The condition(s) and accomplishment of the re-
quired action(s) in accordance with Requirements Bulletin 777-23A0454 RB are also applicable to part
number 100-602201-000-777-53A0070.
Group 1, Configuration 2, 4:
Table 2: Satellite Communications (SATCOM) High Gain Antenna Adapter Plate Inspection
Refer to the listed
procedures in SB
777-23A0454 Origi-
nal Issue or later
approved revi-
sions as an accept-
ed procedure.
Method of
Compliance
ActionCondition
Do PART 1: SAT-
COM HIGH GAIN
ANTENNA
ADAPTER PLATE
REMOVAL
-At the location(s) where part number 100-
602201-000 is installed, do a Detailed
Inspection (DET) of the SATCOM High
Gain Antenna Adapter Plate for corrosion.
Airplanes with SATCOM High
Gain Antenna Adapter Plate(s)
with part number 100-602201-
000 that have been installed for
less than 20 years as of the
Original Issue date of Require-
ments Bulletin 777-23A0454
RB. (d)
-FIGURE 1
Do PART 2: SAT-
COM HIGH GAIN
ANTENNA
ADAPTER PLATE
INSTALLATION
-At the location(s) where part number 100-
602201-000 is installed, repeat the DET
of the SATCOM High Gain Antenna
Adapter Plate for corrosion. (c)
CONDITION 4: NO CORRO-
SION FOUND
Do PART 4: CLOSE
ACCESS
-
-FIGURE 1
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: May 16, 2025
777-23A0454 RB
26 of 39
REQUIREMENTS BULLETIN 777-23A0454
ALERTALERT

### Page 27

Group 1, Configuration 2, 4:
Table 2: Satellite Communications (SATCOM) High Gain Antenna Adapter Plate Inspection
Refer to the listed
procedures in SB
777-23A0454 Origi-
nal Issue or later
approved revi-
sions as an accept-
ed procedure.
Method of
Compliance
ActionCondition
CMC Electronics
CMM 23-15-06
Original Issue, dat-
ed April 16, 2024, or
later revisions.
-OPTION 1 (ACTION 1): Repair the SAT-
COM High Gain Antenna Adapter Plate.
CONDITION 5: ANY CORRO-
SION FOUND WITHIN REPAIR
LIMITS (a)
Do PART 2: SAT-
COM HIGH GAIN
ANTENNA
ADAPTER PLATE
INSTALLATION
-
Do PART 4: CLOSE
ACCESS
-
-FIGURE 1OPTION 1 (ACTION 2): At the location(s)
where part number 100-602201-000 is
installed, repeat the DET of the SATCOM
High Gain Antenna Adapter Plate for
corrosion. (c)
Do PART 3: SAT-
COM HIGH GAIN
ANTENNA
ADAPTER PLATE
REPLACEMENT
-OPTION 2 (ACTION 1): Replace the
SATCOM High Gain Antenna Adapter
Plate with a serviceable SATCOM High
Gain Antenna Adapter Plate. (b)
Do PART 4: CLOSE
ACCESS
-
-FIGURE 1OPTION 2 (ACTION 2): At the location(s)
where part number 100-602201-000 is
installed, repeat the DET of the SATCOM
High Gain Antenna Adapter Plate for
corrosion. (c)
Do PART 3: SAT-
COM HIGH GAIN
ANTENNA
ADAPTER PLATE
REPLACEMENT
-OPTION 3 (ACTION 1): Replace the
SATCOM High Gain Antenna Adapter
plate with a new SATCOM High Gain
Antenna Adapter Plate.
Do PART 4: CLOSE
ACCESS
-
-FIGURE 1
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: May 16, 2025
777-23A0454 RB
27 of 39
REQUIREMENTS BULLETIN 777-23A0454
ALERTALERT

### Page 28

Group 1, Configuration 2, 4:
Table 2: Satellite Communications (SATCOM) High Gain Antenna Adapter Plate Inspection
Refer to the listed
procedures in SB
777-23A0454 Origi-
nal Issue or later
approved revi-
sions as an accept-
ed procedure.
Method of
Compliance
ActionCondition
OPTION 3 (ACTION 2): At the location(s)
where part number 100-602201-000 is
installed, repeat the DET of the SATCOM
High Gain Antenna Adapter Plate for
corrosion. (c)
Do PART 3: SAT-
COM HIGH GAIN
ANTENNA
ADAPTER PLATE
REPLACEMENT
-OPTION 1 (ACTION 1): Replace the
SATCOM High Gain Antenna Adapter
Plate with a serviceable SATCOM High
Gain Antenna Adapter Plate. (b)
CONDITION 6: ANY CORRO-
SION FOUND BEYOND THE
REPAIR LIMITS (a)
Do PART 4: CLOSE
ACCESS
-
-FIGURE 1OPTION 1 (ACTION 2): At the location(s)
where part number 100-602201-000 is
installed, repeat the DET of the SATCOM
High Gain Antenna Adapter Plate for
corrosion. (c)
Do PART 3: SAT-
COM HIGH GAIN
ANTENNA
ADAPTER PLATE
REPLACEMENT
-OPTION 2 (ACTION 1): Replace the
SATCOM High Gain Antenna Adapter
Plate with a new SATCOM High Gain
Antenna Adapter Plate.
Do PART 4: CLOSE
ACCESS
-
-FIGURE 1OPTION 2 (ACTION 2): At the location(s)
where part number 100-602201-000 is
installed, repeat the DET of the SATCOM
High Gain Antenna Adapter Plate for
corrosion. (c)
(a) Any corrosion equal to or less than 0.005 inch into the SATCOM High Gain Antenna Adapter plate is
within repair limits. SATCOM High Gain Antenna Adapter plate repair limits can be found in CMC Electronics
CMM 23-15-06, Original Issue, dated April 16, 2024, or later revisions.
(b) A serviceable SATCOM High Gain Antenna Adapter Plate is one that has been inspected for corrosion
and applicable on-condition corrective actions have been done in accordance with Requirements Bulletin
777-23A0454 RB.
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: May 16, 2025
777-23A0454 RB
28 of 39
REQUIREMENTS BULLETIN 777-23A0454
ALERTALERT

### Page 29

Group 1, Configuration 2, 4:
Table 2: Satellite Communications (SATCOM) High Gain Antenna Adapter Plate Inspection
Refer to the listed
procedures in SB
777-23A0454 Origi-
nal Issue or later
approved revi-
sions as an accept-
ed procedure.
Method of
Compliance
ActionCondition
(c) The removal of SATCOM High Gain Antenna Adapter Plate part number 100-602201-000 after the Original
Issue date of Requirements Bulletin 777-23A0454 RB terminates the repeat DET inspection at the location(s)
where part number 100-602201-000 was installed.
(d) Some High Gain Antenna Adapter Plate(s) with part number 100-602201-000 may have been modified
to 100-602201-000-777-53A0070 per SB 777-53A0070. The condition(s) and accomplishment of the re-
quired action(s) in accordance with Requirements Bulletin 777-23A0454 RB are also applicable to part
number 100-602201-000-777-53A0070.
Group 1, Configuration 3-4:
Table 3: Satellite Communications (SATCOM) High Gain Antenna Adapter Plate Inspection
Refer to the listed
procedures in SB
777-23A0454 Origi-
nal Issue or later
approved revi-
sions as an accept-
ed procedure.
Method of
Compliance
ActionCondition
Do PART 1: SAT-
COM HIGH GAIN
ANTENNA
ADAPTER PLATE
REMOVAL
-At the location(s) where part number 100-
602547-000 is installed, do a Detailed
Inspection (DET) of the SATCOM High
Gain Antenna Adapter Plate for corrosion.
Airplanes with SATCOM High
Gain Antenna Adapter Plate(s)
with part number 100-602547-
000 that have been installed for
20 years or more as of the
Original Issue date of Require-
ments Bulletin 777-23A0454
RB, or the installation date can-
not be determined. (d)
-FIGURE 2
Do PART 2: SAT-
COM HIGH GAIN
ANTENNA
ADAPTER PLATE
INSTALLATION
-At the location(s) where part number 100-
602547-000 is installed, repeat the DET
of the SATCOM High Gain Antenna
Adapter Plate for corrosion. (c)
CONDITION 7: NO CORRO-
SION FOUND
Do PART 4: CLOSE
ACCESS
-
-FIGURE 2
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: May 16, 2025
777-23A0454 RB
29 of 39
REQUIREMENTS BULLETIN 777-23A0454
ALERTALERT

### Page 30

Group 1, Configuration 3-4:
Table 3: Satellite Communications (SATCOM) High Gain Antenna Adapter Plate Inspection
Refer to the listed
procedures in SB
777-23A0454 Origi-
nal Issue or later
approved revi-
sions as an accept-
ed procedure.
Method of
Compliance
ActionCondition
CMC Electronics
CMM 23-15-06
Original Issue, dat-
ed April 16, 2024, or
later revisions.
-OPTION 1 (ACTION 1): Repair the SAT-
COM High Gain Antenna Adapter Plate.
CONDITION 8: ANY CORRO-
SION FOUND WITHIN REPAIR
LIMITS (a)
Do PART 2: SAT-
COM HIGH GAIN
ANTENNA
ADAPTER PLATE
INSTALLATION
-
Do PART 4: CLOSE
ACCESS
-
-FIGURE 2OPTION 1 (ACTION 2): At the location(s)
where part number 100-602547-000 is
installed, repeat the DET of the SATCOM
High Gain Antenna Adapter Plate for
corrosion. (c)
Do PART 3: SAT-
COM HIGH GAIN
ANTENNA
ADAPTER PLATE
REPLACEMENT
-OPTION 2 (ACTION 1): Replace the
SATCOM High Gain Antenna Adapter
Plate with a serviceable SATCOM High
Gain Antenna Adapter Plate. (b)
Do PART 4: CLOSE
ACCESS
-
-FIGURE 2OPTION 2 (ACTION 2): At the location(s)
where part number 100-602547-000 is
installed, repeat the DET of the SATCOM
High Gain Antenna Adapter Plate for
corrosion. (c)
Do PART 3: SAT-
COM HIGH GAIN
ANTENNA
ADAPTER PLATE
REPLACEMENT
-OPTION 3 (ACTION 1): Replace the
SATCOM High Gain Antenna Adapter
Plate with a new SATCOM High Gain
Antenna Adapter Plate.
Do PART 4: CLOSE
ACCESS
-
-FIGURE 2
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: May 16, 2025
777-23A0454 RB
30 of 39
REQUIREMENTS BULLETIN 777-23A0454
ALERTALERT

### Page 31

Group 1, Configuration 3-4:
Table 3: Satellite Communications (SATCOM) High Gain Antenna Adapter Plate Inspection
Refer to the listed
procedures in SB
777-23A0454 Origi-
nal Issue or later
approved revi-
sions as an accept-
ed procedure.
Method of
Compliance
ActionCondition
OPTION 3 (ACTION 2): At the location(s)
where part number 100-602547-000 is
installed, repeat the DET of the SATCOM
High Gain Antenna Adapter Plate for
corrosion. (c)
Do PART 3: SAT-
COM HIGH GAIN
ANTENNA
ADAPTER PLATE
REPLACEMENT
-OPTION 1 (ACTION 1): Replace the
SATCOM High Gain Antenna Adapter
Plate with a serviceable SATCOM High
Gain Antenna Adapter Plate. (b)
CONDITION 9: ANY CORRO-
SION FOUND BEYOND THE
REPAIR LIMITS (a)
Do PART 4: CLOSE
ACCESS
-
-FIGURE 2OPTION 1 (ACTION 2): At the location(s)
where part number 100-602547-000 is
installed, repeat the DET of the SATCOM
High Gain Antenna Adapter Plate for
corrosion. (c)
Do PART 3: SAT-
COM HIGH GAIN
ANTENNA
ADAPTER PLATE
REPLACEMENT
-OPTION 2 (ACTION 1): Replace the
SATCOM High Gain Antenna Adapter
Plate with a new SATCOM High Gain
Antenna Adapter Plate.
Do PART 4: CLOSE
ACCESS
-
-FIGURE 2OPTION 2 (ACTION 2): At the location(s)
where part number 100-602547-000 is
installed, repeat the DET of the SATCOM
High Gain Antenna Adapter Plate for
corrosion. (c)
(a) Any corrosion equal to or less than 0.005 inch into the SATCOM High Gain Antenna Adapter plate is
within repair limits. SATCOM High Gain Antenna Adapter plate repair limits can be found in CMC Electronics
CMM 23-15-06, Original Issue, dated April 16, 2024, or later revisions.
(b) A serviceable SATCOM High Gain Antenna Adapter Plate is one that has been inspected for corrosion
and applicable on-condition corrective actions have been done in accordance with Requirements Bulletin
777-23A0454 RB.
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: May 16, 2025
777-23A0454 RB
31 of 39
REQUIREMENTS BULLETIN 777-23A0454
ALERTALERT

### Page 32

Group 1, Configuration 3-4:
Table 3: Satellite Communications (SATCOM) High Gain Antenna Adapter Plate Inspection
Refer to the listed
procedures in SB
777-23A0454 Origi-
nal Issue or later
approved revi-
sions as an accept-
ed procedure.
Method of
Compliance
ActionCondition
(c) The removal of SATCOM High Gain Antenna Adapter Plate part number 100-602547-000 after the Original
Issue date of Requirements Bulletin 777-23A0454 RB terminates the repeat DET inspection at the location(s)
where part number 100-602547-000 was installed.
(d) Some High Gain Antenna Adapter Plate(s) with part number 100-602547-000 may have been modified
to 100-602547-000-777-53A0070 per SB 777-53A0070. The condition(s) and accomplishment of the re-
quired action(s) in accordance with Requirements Bulletin 777-23A0454 RB are also applicable to part
number 100-602547-000-777-53A0070.
Group 1, Configuration 3-4:
Table 4: Satellite Communications (SATCOM) High Gain Antenna Adapter Plate Inspection
Refer to the listed
procedures in SB
777-23A0454 Origi-
nal Issue or later
approved revi-
sions as an accept-
ed procedure.
Method of
Compliance
ActionCondition
Do PART 1: SAT-
COM HIGH GAIN
ANTENNA
ADAPTER PLATE
REMOVAL
-At the location(s) where part number 100-
602547-000 is installed, do a Detailed
Inspection (DET) of the SATCOM High
Gain Antenna Adapter Plate for corrosion.
Airplanes with SATCOM High
Gain Antenna Adapter Plate(s)
with part number 100-602547-
000 that have been installed for
less than 20 years as of the
Original Issue date of Require-
ments Bulletin 777-23A0454
RB. (d)
-FIGURE 2
Do PART 2: SAT-
COM HIGH GAIN
ANTENNA
ADAPTER PLATE
INSTALLATION
-At the location(s) where part number 100-
602547-000 is installed, repeat the DET
of the SATCOM High Gain Antenna
Adapter Plate for corrosion.(c)
CONDITION 10: NO CORRO-
SION FOUND
Do PART 4: CLOSE
ACCESS
-
-FIGURE 2
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: May 16, 2025
777-23A0454 RB
32 of 39
REQUIREMENTS BULLETIN 777-23A0454
ALERTALERT

### Page 33

Group 1, Configuration 3-4:
Table 4: Satellite Communications (SATCOM) High Gain Antenna Adapter Plate Inspection
Refer to the listed
procedures in SB
777-23A0454 Origi-
nal Issue or later
approved revi-
sions as an accept-
ed procedure.
Method of
Compliance
ActionCondition
CMC Electronics
CMM 23-15-06
Original Issue, dat-
ed April 16, 2024, or
later revisions.
-OPTION 1 (ACTION 1): Repair the SAT-
COM High Gain Antenna Adapter Plate.
CONDITION 11: ANY CORRO-
SION FOUND WITHIN REPAIR
LIMITS (a)
Do PART 2: SAT-
COM HIGH GAIN
ANTENNA
ADAPTER PLATE
INSTALLATION
-
Do PART 4: CLOSE
ACCESS
-
-FIGURE 2OPTION 1 (ACTION 2): At the location(s)
where part number 100-602547-000 is
installed, repeat the DET of the SATCOM
High Gain Antenna Adapter Plate for
corrosion. (c)
Do PART 3: SAT-
COM HIGH GAIN
ANTENNA
ADAPTER PLATE
REPLACEMENT
-OPTION 2 (ACTION 1): Replace the
SATCOM High Gain Antenna Adapter
Plate with a serviceable SATCOM High
Gain Antenna Adapter Plate. (b)
Do PART 4: CLOSE
ACCESS
-
-FIGURE 2OPTION 2 (ACTION 2): At the location(s)
where part number 100-602547-000 is
installed, repeat the DET of the SATCOM
High Gain Antenna Adapter Plate for
corrosion. (c)
Do PART 3: SAT-
COM HIGH GAIN
ANTENNA
ADAPTER PLATE
REPLACEMENT
-OPTION 3 (ACTION 1): Replace the
SATCOM High Gain Antenna Adapter
Plate with a new SATCOM High Gain
Antenna Adapter Plate.
Do PART 4: CLOSE
ACCESS
-
-FIGURE 2
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: May 16, 2025
777-23A0454 RB
33 of 39
REQUIREMENTS BULLETIN 777-23A0454
ALERTALERT

### Page 34

Group 1, Configuration 3-4:
Table 4: Satellite Communications (SATCOM) High Gain Antenna Adapter Plate Inspection
Refer to the listed
procedures in SB
777-23A0454 Origi-
nal Issue or later
approved revi-
sions as an accept-
ed procedure.
Method of
Compliance
ActionCondition
OPTION 3 (ACTION 2): At the location(s)
where part number 100-602547-000 is
installed, repeat the DET of the SATCOM
High Gain Antenna Adapter Plate for
corrosion. (c)
Do PART 3: SAT-
COM HIGH GAIN
ANTENNA
ADAPTER PLATE
REPLACEMENT
-OPTION 1 (ACTION 1): Replace the
SATCOM High Gain Antenna Adapter
Plate with a serviceable SATCOM High
Gain Antenna Adapter Plate. (b)
CONDITION 12: ANY CORRO-
SION FOUND BEYOND THE
REPAIR LIMITS (a)
Do PART 4: CLOSE
ACCESS
-
-FIGURE 2OPTION 1 (ACTION 2): At the location(s)
where part number 100-602547-000 is
installed, repeat the DET of the SATCOM
High Gain Antenna Adapter Plate for
corrosion. (c)
Do PART 3: SAT-
COM HIGH GAIN
ANTENNA
ADAPTER PLATE
REPLACEMENT
-OPTION 2 (ACTION 1): Replace the
SATCOM High Gain Antenna Adapter
Plate with a new SATCOM High Gain
Antenna Adapter Plate.
Do PART 4: CLOSE
ACCESS
-
-FIGURE 2OPTION 2 (ACTION 2): At the location(s)
where part number 100-602547-000 is
installed, repeat the DET of the SATCOM
High Gain Antenna Adapter Plate for
corrosion. (c)
(a) Any corrosion equal to or less than 0.005 inch into the SATCOM High Gain Antenna Adapter plate is
within repair limits. SATCOM High Gain Antenna Adapter plate repair limits can be found in CMC Electronics
CMM 23-15-06, Original Issue, dated April 16, 2024, or later revisions.
(b) A serviceable SATCOM High Gain Antenna Adapter Plate is one that has been inspected for corrosion
and applicable on-condition corrective actions have been done in accordance with Requirements Bulletin
777-23A0454 RB.
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: May 16, 2025
777-23A0454 RB
34 of 39
REQUIREMENTS BULLETIN 777-23A0454
ALERTALERT

### Page 35

Group 1, Configuration 3-4:
Table 4: Satellite Communications (SATCOM) High Gain Antenna Adapter Plate Inspection
Refer to the listed
procedures in SB
777-23A0454 Origi-
nal Issue or later
approved revi-
sions as an accept-
ed procedure.
Method of
Compliance
ActionCondition
(c) The removal of SATCOM High Gain Antenna Adapter Plate part number 100-602547-000 after the Original
Issue date of Requirements Bulletin 777-23A0454 RB terminates the repeat DET inspection at the location(s)
where part number 100-602547-000 was installed.
(d) Some High Gain Antenna Adapter Plate(s) with part number 100-602547-000 may have been modified
to 100-602547-000-777-53A0070 per SB 777-53A0070. The condition(s) and accomplishment of the re-
quired action(s) in accordance with Requirements Bulletin 777-23A0454 RB are also applicable to part
number 100-602547-000-777-53A0070.
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: May 16, 2025
777-23A0454 RB
35 of 39
REQUIREMENTS BULLETIN 777-23A0454
ALERTALERT

### Page 36 (OCR)

REQUIREMENTS BULLETIN 777-23A0454
ALERT  ALERT
This Figure applies only to: Group 1, Configuration 2, 4.
99169
(TOP VIEW)  (BOTTOM VIEW)
SATCOM HIGH GAIN ANTENNA ADAPTER PLATE
DETAILED INSPECTION  3083256
FIGURE 1: SATELLITE COMMUNICATIONS (SATCOM) HIGH GAIN ANTENNA - ADAPTER PLATE, PART
NUMBER 100-602201-000 - DETAILED INSPECTION
(SHEET 1 OF 2)
Original Issue: May 16, 2025
777-23A0454 RB
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details  36 of 39

### Page 37

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
More DataQtyIdentificationNameTaskStep
(a)1100-602201-000SATCOM HIGH GAIN
ANTENNA ADAPTER
PLATE
Inspect1
(a) Do a Detailed Inspection (DET) of the SATCOM High Gain Antenna Adapter Plate for corrosion.
FIGURE 1: SATELLITE COMMUNICATIONS (SATCOM) HIGH GAIN ANTENNA - ADAPTER PLATE, PART
NUMBER 100-602201-000 - DETAILED INSPECTION
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: May 16, 2025
777-23A0454 RB
37 of 39
REQUIREMENTS BULLETIN 777-23A0454
ALERTALERT

### Page 38 (OCR)

REQUIREMENTS BULLETIN 777-23A0454
ALERT  ALERT
This Figure applies only to: Group 1, Configuration 3-4.
(TOP VIEW)  (BOTTOM VIEW)
SATCOM HIGH GAIN ANTENNA ADAPTER PLATE
DETAILED INSPECTION  3083262
FIGURE 2: SATELLITE COMMUNICATIONS (SATCOM) HIGH GAIN ANTENNA - ADAPTER PLATE, PART
NUMBER 100-602547-000 - DETAILED INSPECTION
(SHEET 1 OF 2)
Original Issue: May 16, 2025
777-23A0454 RB
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details  38 of 39

### Page 39

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
More DataQtyIdentificationNameTaskStep
(a)1100-602547-000SATCOM HIGH GAIN
ANTENNA ADAPTER
PLATE
Inspect1
(a) Do a Detailed Inspection (DET) of the SATCOM High Gain Antenna Adapter Plate for corrosion.
FIGURE 2: SATELLITE COMMUNICATIONS (SATCOM) HIGH GAIN ANTENNA - ADAPTER PLATE, PART
NUMBER 100-602547-000 - DETAILED INSPECTION
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: May 16, 2025
777-23A0454 RB
39 of 39
REQUIREMENTS BULLETIN 777-23A0454
ALERTALERT

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
