# Boeing Alert Requirements Bulletin 777-27A0124 RB: No revision named

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2023-0429; AD 2024-01-07 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Alert Requirements Bulletin 777-27A0124 RB](https://openairdocs.org/service-documents/boeing/777-27a0124-rb.md)
- Title as filed: 777-27A0124 RB
- Pages: 6
- PDF: https://openairdocs.org/files/sha256/de/3d/de3d9f874b4cae5d8260796a50b21ec53cf39ce189038396082614f4c3a5753c
- Page: https://openairdocs.org/service-documents/boeing/777-27a0124-rb/file/de3d9f874b4c

## Text

Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Commercial 
Airplanes
777
Requirements Bulletin
ALERT
Number: 777-27A0124 RB
Original Issue: October 27, 2021
ATA System: 2711
SUBJECT: FLIGHT CONTROLS - Aileron and Flaperon Control System - Force Limiter Assemblies
Replacement
THIS DOCUMENT IS SENT TO THE OPERATORS OF RECORD OF THE AIRPLANES SHOWN IN
PARAGRAPH 1.A., EFFECTIVITY. IF AN AIRPLANE HAS BEEN LEASED OR SOLD, SEND THIS DOCUMENT
TO THE NEW OPERATOR. IF APPLICABLE SPARES HAVE BEEN SOLD, SEND THIS DOCUMENT TO THE
NEW OWNER. THIS IS AN ENHANCED REQUIRED FOR COMPLIANCE DOCUMENT. THE BOEING
PROCESSES USED TO CREATE THE SERVICE BULLETIN (SB) AND THE REQUIREMENTS BULLETIN
(RB) ENSURE THAT THE INFORMATION BETWEEN "RC START" AND "RC END" IN THE SB ARE IDENTICAL
TO THE INFORMATION IN THE SAME SECTIONS (COMPLIANCE, WORK INSTRUCTIONS…) OF THE RB
WHICH THE SB REFERS TO AS THE RELATED DOCUMENT.
1. Effectivity
A. Airplanes
This bulletin is applicable to 777-200LR, 777-300ER, 777F Airplane(s), line number(s) 1531-1566,
1568-1573, 1575-1580, 1582-1586, 1588-1604, 1606-1610, 1612-1614, 1616-1619, 1621-1623,
1625-1628, 1630-1632, 1634-1637, 1639-1641, 1643-1646, 1648-1650, 1652-1655, 1657-1658,
1660-1667, 1669, 1671, 1673, 1675-1676, 1678-1679, 1681, 1683-1684, 1686-1687, 1689-1707
in 1 Group(s). Where the effectivity is presented with hyphens between line numbers, the airplane
applicability means "through" and "inclusive", e.g. line numbers 1-9 means line numbers 1 through
9 inclusive.
The Variable Numbers and Group Information for the applicable airplanes is given below. An
equivalent change is on subsequent production airplanes.
DESCRIPTIONCONFIGURATIONGROUP
777-200LR, 777-300ER, 777F airplanes with Force Limiter
Assemblies P/N 253W1263-1 that have a higher than normal breakout
force.
-1
Airplane Models:
777-200LR, 777-300ER, 777F
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 27, 2021
777-27A0124 RB
5 of 10

### Page 2

GroupVariable Number
1WD123
1WD156
1WE347 - WE350
1WE366 - WE368
1WE406 - WE411
1WE479 - WE484
1WE572 - WE573
1WE584 - WE587
1WE683 - WE689
1WE765 - WE772
1WE797 - WE798
1WE801 - WE806
GroupVariable Number
1WE827 - WE828
1WE831 - WE835
1WE851 - WE853
1WE856 - WE857
1WE861 - WE863
1WE866 - WE868
1WE871
1WF028 - WF029
1WF071 - WF074
1WF161 - WF165
1WF180
1WF201
GroupVariable Number
1WF209 - WF215
1WF222 - WF227
1WF231 - WF248
1WF256 - WF258
1WF261 - WF262
1WF266 - WF279
1WF281 - WF288
1WF296
1WF301 - WF304
1WF311 - WF313
1WF321
1WF336 - WF337
B. Spares Affected
None.
2. CONCURRENT REQUIREMENTS
None.
3. COMPLIANCE
The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to
Requirements Bulletin 777-27A0124 RB. The Airworthiness Directive will make the compliance tasks and
times given in Requirements Bulletin 777-27A0124 RB mandatory.
Accomplish the required action(s), based on the applicable condition(s) in Table 1 , in accordance with
Accomplishment Instructions.
Table 1: Force Limiter Assemblies Replacement
Repeat Interval
(Not to Exceed)
Boeing Recommended
Compliance Time
ActionCondition
-Within 12 months after
the Original Issue date of
Requirements Bulletin
777-27A0124 RB or
within 12 months after
the date of issuance of
the original standard cer-
tificate of airworthiness
or the original export cer-
tificate of airworthiness,
whichever occurs later.
Replace the existing low-
er and upper Force Lim-
iter assemblies part num-
ber 253W1263-1 with
new lower and upper
Force Limiter assemblies
part number 253W1263-
3.
All airplanes
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 27, 2021
777-27A0124 RB
6 of 10
REQUIREMENTS BULLETIN 777-27A0124
ALERTALERT

### Page 3

4. APPROVAL
This Requirements Bulletin was examined by the Federal Aviation Administration (FAA). The changes
specified in this document comply with the applicable regulations and are FAA approved, as well as European
Union Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved
airplanes listed in this Requirements Bulletin effectivity. This document and its approval were based on the
airplane in its original Boeing delivery configuration or as modified by other Boeing changes.
If an airplane has a non-Boeing modification or repair that affects a component or system also affected by
this Requirements Bulletin, the operator is responsible for obtaining appropriate regulatory agency approval
before incorporating this Requirements Bulletin.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 27, 2021
777-27A0124 RB
7 of 10
REQUIREMENTS BULLETIN 777-27A0124
ALERTALERT

### Page 4

Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 27, 2021
777-27A0124 RB
8 of 10
REQUIREMENTS BULLETIN 777-27A0124
ALERTALERT
BLANK PAGE

### Page 5

5.    ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL INFORMATION
NOTE: 1. This is an Enhanced Required for Compliance document. There will be a separate
Service Bulletin (SB) and a separate Requirements Bulletin (RB). If an RB is mandated
by an Airworthiness Directive (AD), then all applicable requirements specified in the
RB must be done. For the related SB, some locations are marked RC Start and RC
End to identify the requirements that are restated from the RB. For the related SB,
the areas between RC Start and RC End, including sub-steps and any figures
identified between RC Start and RC End, must be done to comply with the AD.
Therefore, an Alternative Method of Compliance (AMOC) is required for any deviations
to steps between RC Start and RC End, including substeps and identified figures.
For the related SB, the steps not between RC Start and RC End may be deviated
from using accepted methods in accordance with the operator's maintenance or
inspection program without obtaining approval of an AMOC; this is provided that the
steps between RC Start and RC End, including sub-steps and identified figures, can
still be done as specified, and the airplane can be put back in an airworthy condition.
Figures not required for compliance are omitted from the RB.
2. This is an Enhanced Required for Compliance document. The Boeing processes
used to create the Service Bulletin (SB) and the Requirements Bulletin (RB) ensure
that the information between "RC Start" and "RC End" in the SB are identical to the
information in the same sections (Compliance, Work Instructions...) of the RB which
the SB refers to as the related document.
3. The compliance times for the actions in WORK INSTRUCTIONS are in Compliance.
4. Unless shown differently, these dimensions and tolerances are used:
– Linear dimensions are in inches
– Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus
or minus 0.03 inch
– Tolerance on rivet and bolt edge margin is plus or minus 0.05 inch
– Angular tolerance is plus or minus 2 degrees
– Hole dimensions for standard solid rivets and fasteners are in Structural Repair
Manual (SRM) Chapter 51
– Torque Values:
— Values for structural fasteners are given in 777 Structural Repair Manual,
Chapter 51.
— Values for airframe maintenance tasks are included in Chapter 20 of 777
Aircraft Maintenance Manual (AMM).
— Values for electrical maintenance tasks are included in Chapter 20 of
Standard Wiring Practices Manual (SWPM).
— Values for engine maintenance tasks are included in Chapter 70 of 777
Aircraft Maintenance Manual (AMM).
— Non-standard torque values for maintenance tasks are included in the
applicable installation step.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 27, 2021
777-27A0124 RB
9 of 10
REQUIREMENTS BULLETIN 777-27A0124
ALERTALERT

### Page 6

5. These work instructions refer to procedures included in other Boeing documents.
When the words "refer to" are used and the operator has an accepted alternative
procedure, the accepted alternative procedure can be used. When the words "in
accordance with" are included in the instruction, the procedure in the Boeing document
must be used.
6. Where the work instructions include installation of a kept part, a new or serviceable
part with the same part number can be installed as an alternative to the kept part.
7. If it is necessary to remove more parts for access, you can remove those parts. If
you can get access without removing identified parts, it is not necessary to remove
all of the identified parts. Jacking and shoring limitations must be observed.
8. Use the approved fastener, process and material substitutions in accordance with
SRM Chapter 51.
9. The instructions in Work Instructions and the figures can include operation of tools
or test equipment. Boeing Engineering Tool Drawings, the Illustrated Tool and
Equipment Manual, and the Special Tool and Ground Handling Drawing Index contain
data on versions of the tools or test equipment that you can use. It is permitted to
use replaced tools. It is not permitted to use superseded tools.
10. If the length of any fastener specified in this service bulletin does not meet installation
standards given in SRM Chapter 51, then a fastener of the same specification, or
an approved substitute, with a length which meets the installation standards given
in SRM Chapter 51 may be used. In addition, washers may be installed for fastener
grip length in accordance with SRM Chapter 51. Refer to SOPM 20-50-01 for alternate
full threaded fasteners (screws) needed for installation in this service bulletin.
B. WORK INSTRUCTIONS
Actions Required for Compliance
1. Requirements
Table 1: Force Limiter Assemblies Replacement
Refer to the listed proce-
dures in SB 777-27A0124
Original Issue or later
approved revisions as an
accepted procedure.
Method of ComplianceActionCondition
PART 1: OPEN ACCESS-Replace the existing lower
and upper Force Limiter
assemblies part number
253W1263-1 with new
lower and upper Force
Limiter assemblies part
number 253W1263-3.
All airplanes
PART 2: FORCE LIMITER
ASSEMBLIES REPLACE-
MENT
-
PART 3: CLOSE ACCESS-
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 27, 2021
777-27A0124 RB
10 of 10
REQUIREMENTS BULLETIN 777-27A0124
ALERTALERT

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
