# Boeing Alert Requirements Bulletin 777-31A0342 RB: No revision named

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2022-0598; AD 2024-04-09 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Alert Requirements Bulletin 777-31A0342 RB](https://openairdocs.org/service-documents/boeing/777-31a0342-rb.md)
- Title as filed: 777-31A0342 RB
- Pages: 20
- PDF: https://openairdocs.org/files/sha256/3e/f8/3ef8de04a8d8cce63b07e98876f014e01cae4e3ca5609c0969e658d63334a67d
- Page: https://openairdocs.org/service-documents/boeing/777-31a0342-rb/file/3ef8de04a8d8

## Text

Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Commercial 
Airplanes
777
Requirements Bulletin
ALERT
Number: 777-31A0342 RB
Original Issue: July 19, 2021
ATA System: 3141
SUBJECT: INDICATING/RECORDING SYSTEMS - Airplane Information Management System
(AIMS) - Block Point Version 17C Software Change
Export of this technology is controlled under the United States Export Administration Regulations (EAR) (15
CFR 300-774). An export license may be required before it is used for development, production or use by foreign
persons from specific countries. The controller of this data has the individual responsibility to abide by all export
laws.
9E991ECCN:
Copyright © 2021 Boeing.
Unpublished Work. All Rights Reserved.
Treatment of this document and its content is governed by contract with Boeing. Rights to use this document
are licensed on a per aircraft basis and such rights may not be transferable. For more information, contact The
Boeing Company.
Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner,
BBJ, DC-8, DC-9, DC-10, KC-10, KC-46, KDC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8, Poseidon and
Boeing liveries are all trademarks owned by The Boeing Company; and no trademark license is granted in
connection with this document unless provided in writing by Boeing.
Original Issue: July 19, 2021
777-31A0342 RB
1 of 20
3.0

### Page 2

Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 19, 2021
777-31A0342 RB
2 of 20
REQUIREMENTS BULLETIN 777-31A0342
ALERTALERT
BLANK PAGE

### Page 3

Table of Contents
1. EFFECTIVITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
A. Airplanes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
B. Spares Affected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2. CONCURRENT REQUIREMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3. COMPLIANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4. APPROVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
5. ACCOMPLISHMENT INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
A. General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
B. Work Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 19, 2021
777-31A0342 RB
3 of 20
REQUIREMENTS BULLETIN 777-31A0342
ALERTALERT

### Page 4

Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 19, 2021
777-31A0342 RB
4 of 20
REQUIREMENTS BULLETIN 777-31A0342
ALERTALERT
BLANK PAGE

### Page 5

Commercial 
Airplanes
777
Requirements Bulletin
ALERT
Number: 777-31A0342 RB
Original Issue: July 19, 2021
ATA System: 3141
SUBJECT: INDICATING/RECORDING SYSTEMS - Airplane Information Management System
(AIMS) - Block Point Version 17C Software Change
THIS DOCUMENT IS SENT TO THE OPERATORS OF RECORD OF THE AIRPLANES SHOWN IN
PARAGRAPH 1.A., EFFECTIVITY. IF AN AIRPLANE HAS BEEN LEASED OR SOLD, SEND THIS DOCUMENT
TO THE NEW OPERATOR. IF APPLICABLE SPARES HAVE BEEN SOLD, SEND THIS DOCUMENT TO THE
NEW OWNER. THIS IS AN ENHANCED REQUIRED FOR COMPLIANCE DOCUMENT. THE BOEING
PROCESSES USED TO CREATE THE SERVICE BULLETIN (SB) AND THE REQUIREMENTS BULLETIN
(RB) ENSURE THAT THE INFORMATION BETWEEN "RC START" AND "RC END" IN THE SB ARE IDENTICAL
TO THE INFORMATION IN THE SAME SECTIONS (COMPLIANCE, WORK INSTRUCTIONS…) OF THE RB
WHICH THE SB REFERS TO AS THE RELATED DOCUMENT.
1. Effectivity
A. Airplanes
This bulletin is applicable to 777-200, 777-200LR, 777-300, 777-300ER, 777F Airplane(s), line
number(s) 1-1566, 1568-1573, 1575-1580, 1582-1586, 1588-1604, 1606-1610, 1612-1614,
1616-1619, 1621-1623, 1625-1628, 1630-1632, 1634-1637, 1639-1641, 1643-1646, 1648-1650,
1652-1655, 1657-1658, 1660-1667, 1669, 1671, 1673, 1675-1676, 1678-1679, 1681, 1683-1684,
1686-1687, 1689-1693 in 5 Group(s). Where the effectivity is presented with hyphens between
line numbers, the airplane applicability means "through" and "inclusive", e.g. line numbers 1-9
means line numbers 1 through 9 inclusive.
The Variable Numbers and Group Information for the applicable airplanes is given below.
DESCRIPTIONCONFIGURATIONGROUP
Airplanes with Airplane Information Management System (AIMS)-2
with service bulletin 777-31-0294 incorporated.
-1
Airplanes with AIMS-2 with service bulletin 777-31-0331 incorporated.-2
Airplanes with AIMS-2 with service bulletin 777-31-0332 incorporated.-3
Airplanes delivered with AIMS-2 Block Point (BP) Version 17B
software.
-4
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 19, 2021
777-31A0342 RB
5 of 20

### Page 6

DESCRIPTIONCONFIGURATIONGROUP
Airplanes with Airplane Information Management System (AIMS)-1.-5
Airplane Models:
777-200, 777-200LR, 777-300, 777-300ER, 777F
GroupVariable Number
1WA001
5WA002 - WA017
1WA076 - WA078
5WA079 - WA080
5WA086 - WA093
1WA101 - WA104
5WA116 - WA119
5WA131 - WA137
5WA171 - WA175
5WA196 - WA198
5WA206 - WA212
5WA221 - WA223
5WA231 - WA232
5WA241 - WA250
5WA261 - WA266
1WA281 - WA283
1WA301 - WA304
1WB001 - WB021
1WB031 - WB042
5WB043
1WB044 - WB046
1WB051 - WB069
5WB070
1WB071
5WB072 - WB073
1WB074 - WB088
GroupVariable Number
5WB101 - WB106
5WB121 - WB125
5WB131 - WB136
1WB137 - WB148
5WB151 - WB155
5WB161 - WB175
1WB176 - WB177
5WB181 - WB192
1WB193 - WB194
5WB201 - WB214
1WB215
5WB231 - WB247
1WB271 - WB273
5WB276 - WB286
5WB291 - WB302
5WB306 - WB307
2WB311 - WB312
5WB313
2WB314 - WB315
5WB316
2WB317
5WB318
2WB319 - WB326
5WB327 - WB328
2WB329
5WB330
GroupVariable Number
2WB331
5WB332 - WB333
2WB334 - WB335
1WB336
5WB337
5WB341
1WB342
5WB366 - WB367
1WB368
1WB371 - WB388
5WB406
1WB411 - WB413
1WB416 - WB439
1WB446 - WB453
1WB476
3WB481 - WB484
1WB501 - WB512
5WB531 - WB535
3WB536 - WB537
5WB551 - WB554
5WB591 - WB593
1WB594 - WB597
5WB601 - WB606
1WB611 - WB615
5WB616 - WB618
1WB619 - WB622
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 19, 2021
777-31A0342 RB
6 of 20
REQUIREMENTS BULLETIN 777-31A0342
ALERTALERT

### Page 7

GroupVariable Number
5WB631 - WB632
1WB633
5WB634
1WB635
5WB636 - WB637
1WB638
5WB646
1WB647
5WB648
1WB649
1WC051 - WC073
1WC101 - WC104
5WC111 - WC113
1WC114 - WC120
1WC221 - WC224
1WC241 - WC243
5WC281 - WC286
1WC287 - WC290
1WC301 - WC308
5WC361 - WC362
1WC363 - WC364
5WC371 - WC372
1WC373 - WC374
1WC381 - WC395
1WC441
1WC446 - WC449
1WC456 - WC459
1WC486 - WC493
1WC506 - WC508
1WC521 - WC522
1WC531 - WC536
1WC546 - WC548
1WC556
GroupVariable Number
1WC566 - WC567
1WC571 - WC574
1WC581
1WC586 - WC587
1WC591 - WC595
1WD001 - WD002
1WD011 - WD018
1WD031 - WD036
1WD046 - WD055
1WD066 - WD075
1WD081 - WD089
1WD091
1WD096
1WD101 - WD106
1WD111 - WD112
1WD116 - WD117
1WD121 - WD122
4WD123
1WD156
1WD501 - WD513
1WD521 - WD541
1WD546 - WD554
1WD561 - WD573
1WD581 - WD599
1WD606 - WD609
1WD621 - WD632
1WD651 - WD665
1WD671 - WD677
1WD691 - WD709
1WD741 - WD752
1WD761 - WD771
1WD786 - WD788
1WD796 - WD837
GroupVariable Number
1WD846 - WD867
1WD871 - WD918
1WD921 - WD957
1WD966 - WD970
1WD981 - WD982
1WD986 - WD987
1WD991 - WD996
1WE001 - WE007
1WE011 - WE012
1WE021 - WE026
1WE031 - WE040
1WE051 - WE057
1WE071 - WE078
1WE081 - WE084
1WE091 - WE095
1WE126 - WE178
1WE186 - WE219
1WE226 - WE231
1WE236 - WE253
1WE261 - WE267
1WE271 - WE278
1WE291 - WE298
1WE301 - WE320
1WE331 - WE349
4WE350
1WE351 - WE356
1WE366 - WE368
1WE376 - WE377
1WE381
1WE386 - WE387
1WE391 - WE392
1WE396 - WE409
4WE410 - WE411
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 19, 2021
777-31A0342 RB
7 of 20
REQUIREMENTS BULLETIN 777-31A0342
ALERTALERT

### Page 8

GroupVariable Number
1WE416 - WE420
1WE426 - WE431
1WE436 - WE446
1WE451 - WE484
1WE486 - WE493
1WE495 - WE499
1WE501 - WE504
1WE511 - WE516
1WE526 - WE528
1WE536 - WE549
1WE556 - WE571
4WE572 - WE573
1WE576 - WE587
1WE591
1WE601 - WE605
1WE626 - WE627
1WE631
1WE641 - WE642
1WE646 - WE647
1WE651 - WE661
1WE666 - WE677
1WE681 - WE689
1WE701 - WE705
1WE711 - WE712
GroupVariable Number
1WE731 - WE732
1WE736 - WE740
1WE746 - WE768
4WE769 - WE772
1WE776 - WE786
1WE791 - WE792
1WE796 - WE798
1WE801 - WE805
4WE806
1WE811 - WE812
1WE826 - WE828
1WE831 - WE835
1WE851 - WE853
4WE856
4WE861 - WE863
4WE866 - WE868
4WE871
1WF001 - WF004
1WF016 - WF027
4WF028 - WF029
1WF031 - WF043
1WF046 - WF077
1WF081 - WF088
1WF096 - WF101
GroupVariable Number
1WF106 - WF109
1WF111 - WF124
1WF131 - WF144
1WF146 - WF147
1WF151 - WF152
1WF156 - WF164
4WF165
1WF166 - WF173
1WF176 - WF184
1WF191
1WF201
1WF206 - WF217
1WF221 - WF225
1WF231 - WF242
4WF243 - WF244
1WF246 - WF248
1WF256 - WF257
4WF258
1WF261 - WF262
1WF266 - WF269
4WF270 - WF276
4WF281 - WF288
4WF311 - WF313
4WF321
B. Spares Affected
None.
2. CONCURRENT REQUIREMENTS
The service bulletin listed below must be done before or at the same time as this service bulletin:
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 19, 2021
777-31A0342 RB
8 of 20
REQUIREMENTS BULLETIN 777-31A0342
ALERTALERT

### Page 9

Group 1:
DescriptionService BulletinCompany
INDICATING/RECORDING SYSTEMS -
Airplane Information Management System -
Airplane Information Management System
2 Block Point V17B Software Change
777-31-0294 Original Issue or Revision 1Boeing
Group 2:
DescriptionService BulletinCompany
INDICATING/RECORDING SYSTEMS -
Airplane Information Management System
(AIMS) - Replacement of AIMS-1 and
PlaneNet-1 systems with AIMS-2 and
PlaneNet-2 systems
777-31-0331 Original Issue or Revision 1Boeing
Group 3:
DescriptionService BulletinCompany
INDICATING/RECORDING SYSTEMS -
Airplane Information Management System
(AIMS) - Replacement of the AIMS-1 with
AIMS-2 and Installation of Software
777-31-0332 Original Issue or Revision 1Boeing
Group 4-5:
None.
3. COMPLIANCE
The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to
Requirements Bulletin 777-31A0342 RB. The Airworthiness Directive will make the compliance tasks and
times given in Requirements Bulletin 777-31A0342 RB mandatory.
Federal Aviation Administration (FAA) Airworthiness Directive AD 2009-02-05 is related to this bulletin. The
effective date of AD 2009-02-05 is April 2, 2009.
Federal Aviation Administration (FAA) Airworthiness Directive AD 2011-09-05 is related to this bulletin. The
effective date of AD 2011-09-05 is May 26, 2011.
Federal Aviation Administration (FAA) Airworthiness Directive AD 2012-16-04 is related to this bulletin. The
effective date of AD 2012-16-04 is October 3, 2012.
Federal Aviation Administration (FAA) Airworthiness Directive AD 2018-26-05 is related to this bulletin. The
effective date of AD 2018-26-05 is February 1, 2019.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 19, 2021
777-31A0342 RB
9 of 20
REQUIREMENTS BULLETIN 777-31A0342
ALERTALERT

### Page 10

Accomplish the required action(s), based on the applicable condition(s) in Table(s) 1-3, in accordance with
Accomplishment Instructions.
When more than one OPTION is given for a CONDITION, do only one of the OPTION numbers. When
more than one ACTION is given for a CONDITION or an OPTION, do all of the ACTION numbers for that
CONDITION or OPTION.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 19, 2021
777-31A0342 RB
10 of 20
REQUIREMENTS BULLETIN 777-31A0342
ALERTALERT

### Page 11

Group 1-3:
Table 1: Airplane Information Management System Software Installation
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
-Within 12 months after
the Original Issue date
of Requirements Bul-
letin 777-31A0342 RB.
ACTION 1: Do all applicable actions
in accordance with the Accomplish-
ment Instructions of the Service
Bulletin specified in CONCURRENT
REQUIREMENTS.
All Airplanes
-ACTION 2: Install the AIMS-2 BP
V17C software part numbers
HNP5C-AL01-1007, HNP5D-AL02-
1014, HNP5A-AL03-1012, HNP59-
AL04-1007, HNP5F-AL05-1011,
HNP5B-AL06-1007 and HNP55-
AD07-1011 or later approved soft-
ware part numbers in the right
AIMS cabinet.
-ACTION 3: Install the AIMS-2 BP
V17C software part numbers
HNP5C-AL01-1007, HNP5D-AL02-
1014, HNP5A-AL03-1012, HNP59-
AL04-1007, HNP5F-AL05-1011,
HNP5B-AL06-1007 and HNP55-
AD07-1011 or later approved soft-
ware part numbers in the left AIMS
cabinet.
-ACTION 4: Do a software configu-
ration check and make sure that
software part numbers HNP5C-
AL01-1007, HNP5D-AL02-1014,
HNP5A-AL03-1012, HNP59-AL04-
1007, HNP5F-AL05-1011, HNP5B-
AL06-1007 and HNP55-AD07-1011
or later approved software part
numbers are installed in the right
and left AIMS cabinets. If software
part numbers HNP5C-AL01-1007,
HNP5D-AL02-1014, HNP5A-AL03-
1012, HNP59-AL04-1007, HNP5F-
AL05-1011, HNP5B-AL06-1007 and
HNP55-AD07-1011 or later ap-
proved software part numbers are
not shown as installed in the right
and left AIMS cabinets, do correc-
tive action(s) until the software part
numbers are shown as installed in
the right and left AIMS cabinets.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 19, 2021
777-31A0342 RB
11 of 20
REQUIREMENTS BULLETIN 777-31A0342
ALERTALERT

### Page 12

Group 4:
Table 2: Airplane Information Management System Software Installation
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
-Within 12 months after
the Original Issue date
of Requirements Bul-
letin 777-31A0342 RB.
ACTION 1: Install the AIMS-2 BP
V17C software part numbers
HNP5C-AL01-1007, HNP5D-AL02-
1014, HNP5A-AL03-1012, HNP59-
AL04-1007, HNP5F-AL05-1011,
HNP5B-AL06-1007 and HNP55-
AD07-1011 or later approved soft-
ware part numbers in the right
AIMS cabinet.
All Airplanes
-ACTION 2: Install the AIMS-2 BP
V17C software part numbers
HNP5C-AL01-1007, HNP5D-AL02-
1014, HNP5A-AL03-1012, HNP59-
AL04-1007, HNP5F-AL05-1011,
HNP5B-AL06-1007 and HNP55-
AD07-1011 or later approved soft-
ware part numbers in the left AIMS
cabinet.
-ACTION 3: Do a software configu-
ration check and make sure that
software part numbers HNP5C-
AL01-1007, HNP5D-AL02-1014,
HNP5A-AL03-1012, HNP59-AL04-
1007, HNP5F-AL05-1011, HNP5B-
AL06-1007 and HNP55-AD07-1011
or later approved software part
numbers are installed in the right
and left AIMS cabinets. If software
part numbers HNP5C-AL01-1007,
HNP5D-AL02-1014, HNP5A-AL03-
1012, HNP59-AL04-1007, HNP5F-
AL05-1011, HNP5B-AL06-1007 and
HNP55-AD07-1011 or later ap-
proved software part numbers are
not shown as installed in the right
and left AIMS cabinets, do correc-
tive action(s) until the software part
numbers are shown as installed in
the right and left AIMS cabinets.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 19, 2021
777-31A0342 RB
12 of 20
REQUIREMENTS BULLETIN 777-31A0342
ALERTALERT

### Page 13

Group 5:
Table 3: Airplane Information Management System Software Installation
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
-Within 36 months after
the Original Issue date
of Requirements Bul-
letin 777-31A0342 RB.
ACTION 1: Contact The Boeing
Company for instructions for upgrad-
ing to AIMS-2 configurations and
do as instructed by Boeing.
All Airplanes
-ACTION 2: Install the AIMS-2 BP
V17C software part numbers
HNP5C-AL01-1007, HNP5D-AL02-
1014, HNP5A-AL03-1012, HNP59-
AL04-1007, HNP5F-AL05-1011,
HNP5B-AL06-1007 and HNP55-
AD07-1011 or later approved soft-
ware part numbers in the right
AIMS cabinet.
-ACTION 3: Install the AIMS-2 BP
V17C software part numbers
HNP5C-AL01-1007, HNP5D-AL02-
1014, HNP5A-AL03-1012, HNP59-
AL04-1007, HNP5F-AL05-1011,
HNP5B-AL06-1007 and HNP55-
AD07-1011 or later approved soft-
ware part numbers in the left AIMS
cabinet.
-ACTION 4: Do a software configu-
ration check and make sure that
software part numbers HNP5C-
AL01-1007, HNP5D-AL02-1014,
HNP5A-AL03-1012, HNP59-AL04-
1007, HNP5F-AL05-1011, HNP5B-
AL06-1007 and HNP55-AD07-1011
or later approved software part
numbers are installed in the right
and left AIMS cabinets. If software
part numbers HNP5C-AL01-1007,
HNP5D-AL02-1014, HNP5A-AL03-
1012, HNP59-AL04-1007, HNP5F-
AL05-1011, HNP5B-AL06-1007 and
HNP55-AD07-1011 or later ap-
proved software part numbers are
not shown as installed in the right
and left AIMS cabinets, do correc-
tive action(s) until the software part
numbers are shown as installed in
the right and left AIMS cabinets.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 19, 2021
777-31A0342 RB
13 of 20
REQUIREMENTS BULLETIN 777-31A0342
ALERTALERT

### Page 14

4. APPROVAL
This Requirements Bulletin was examined by the Federal Aviation Administration (FAA). The changes
specified in this document comply with the applicable regulations and are FAA approved, as well as European
Union Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved
airplanes listed in this Requirements Bulletin effectivity. This document and its approval were based on the
airplane in its original Boeing delivery configuration or as modified by other Boeing changes.
If an airplane has a non-Boeing modification or repair that affects a component or system also affected by
this Requirements Bulletin, the operator is responsible for obtaining appropriate regulatory agency approval
before incorporating this Requirements Bulletin.
In addition, the Manager of the FAA Seattle ACO Branch approves the installation of AIMS-2 BP V17C
software defined in this Requirements Bulletin as an alternative method of compliance to the requirements
of paragraph (f) of AD 2009-02-05. All provisions of AD 2009-02-05 that are not specifically referenced in
the above statement remain fully applicable and must be complied with accordingly.
In addition, the Manager of the FAA Seattle ACO Branch approves the installation of AIMS-2 BP V17C
software defined in this Requirements Bulletin as an alternative method of compliance to the requirements
of paragraph (i)(2) of AD 2011-09-05. All provisions of AD 2011-09-05 that are not specifically referenced
in the above statement remain fully applicable and must be complied with accordingly.
In addition, the Manager of the FAA Seattle ACO Branch approves the installation of AIMS-2 BP V17C
software defined in this Requirements Bulletin as an alternative method of compliance to the requirements
of paragraph (h) of AD 2012-16-04. All provisions of AD 2012-16-04 that are not specifically referenced in
the above statement remain fully applicable and must be complied with accordingly.
In addition, the Manager of the FAA Seattle ACO Branch approves the installation of AIMS-2 BP V17C
software defined in this Requirements Bulletin as an alternative method of compliance to the requirements
of paragraph (g)(2)(ii) of AD 2018-26-05. All provisions of AD 2018-26-05 that are not specifically referenced
in the above statement remain fully applicable and must be complied with accordingly.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 19, 2021
777-31A0342 RB
14 of 20
REQUIREMENTS BULLETIN 777-31A0342
ALERTALERT

### Page 15

5.    ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL INFORMATION
NOTE: 1. This is an Enhanced Required for Compliance document. There will be a separate
Service Bulletin (SB) and a separate Requirements Bulletin (RB). If an RB is mandated
by an Airworthiness Directive (AD), then all applicable requirements specified in the
RB must be done. For the related SB, some locations are marked RC Start and RC
End to identify the requirements that are restated from the RB. For the related SB,
the areas between RC Start and RC End, including sub-steps and any figures
identified between RC Start and RC End, must be done to comply with the AD.
Therefore, an Alternative Method of Compliance (AMOC) is required for any deviations
to steps between RC Start and RC End, including substeps and identified figures.
For the related SB, the steps not between RC Start and RC End may be deviated
from using accepted methods in accordance with the operator's maintenance or
inspection program without obtaining approval of an AMOC; this is provided that the
steps between RC Start and RC End, including sub-steps and identified figures, can
still be done as specified, and the airplane can be put back in an airworthy condition.
Figures not required for compliance are omitted from the RB.
2. This is an Enhanced Required for Compliance document. The Boeing processes
used to create the Service Bulletin (SB) and the Requirements Bulletin (RB) ensure
that the information between "RC Start" and "RC End" in the SB are identical to the
information in the same sections (Compliance, Work Instructions...) of the RB which
the SB refers to as the related document.
3. The compliance times for the actions in WORK INSTRUCTIONS are in Compliance.
4. Later approved software is only software that is approved by Boeing as a replacement
for the software specified in this bulletin and approved as part of the type design by
the Federal Aviation Administration (FAA) after issuance of this bulletin Original Issue
date.
5. These work instructions refer to procedures included in other Boeing documents.
When the words "refer to" are used and the operator has an accepted alternative
procedure, the accepted alternative procedure can be used. When the words "in
accordance with" are included in the instruction, the procedure in the Boeing document
must be used.
6. When more than one OPTION is given for a CONDITION, do only one of the OPTION
numbers. When more than one ACTION is given for a CONDITION or an OPTION,
do all of the ACTION numbers for that CONDITION or OPTION.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 19, 2021
777-31A0342 RB
15 of 20
REQUIREMENTS BULLETIN 777-31A0342
ALERTALERT

### Page 16

B. WORK INSTRUCTIONS
Actions Required for Compliance
1. Requirements:
Group 1-3:
Table 1: Airplane Information Management System Software Installation
Refer to the listed pro-
cedures in SB 777-
31A0342 Original Issue
or later approved revi-
sions as an accepted
procedure.
Method of
Compliance
ActionCondition
--ACTION 1: Do all applicable actions
in accordance with the Accomplish-
ment Instructions of the Service
Bulletin specified in CONCURRENT
REQUIREMENTS.
All Airplanes
PART 1: Right Airplane
Information Management
System Cabinet Software
Installation and Software
Configuration Check.
-ACTION 2: Install the Airplane Infor-
mation Management System 2
(AIMS-2) Block Point (BP) Version
17C software part numbers
HNP5C-AL01-1007, HNP5D-AL02-
1014, HNP5A-AL03-1012, HNP59-
AL04-1007, HNP5F-AL05-1011,
HNP5B-AL06-1007 and HNP55-
AD07-1011 or later approved soft-
ware part numbers in the right
AIMS cabinet.
PART 2: Left Airplane In-
formation Management
System Cabinet Software
Installation and Software
Configuration Check.
-ACTION 3: Install the AIMS-2 BP
V17C software part numbers
HNP5C-AL01-1007, HNP5D-AL02-
1014, HNP5A-AL03-1012, HNP59-
AL04-1007, HNP5F-AL05-1011,
HNP5B-AL06-1007 and HNP55-
AD07-1011 or later approved soft-
ware part numbers in the left AIMS
cabinet.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 19, 2021
777-31A0342 RB
16 of 20
REQUIREMENTS BULLETIN 777-31A0342
ALERTALERT

### Page 17

Group 1-3:
Table 1: Airplane Information Management System Software Installation
Refer to the listed pro-
cedures in SB 777-
31A0342 Original Issue
or later approved revi-
sions as an accepted
procedure.
Method of
Compliance
ActionCondition
PART 1: Right Airplane
Information Management
System Cabinet Software
Installation and Software
Configuration Check.
-ACTION 4: Do a software configu-
ration check and make sure that
software part numbers HNP5C-
AL01-1007, HNP5D-AL02-1014,
HNP5A-AL03-1012, HNP59-AL04-
1007, HNP5F-AL05-1011, HNP5B-
AL06-1007 and HNP55-AD07-1011
or later approved software part
numbers are installed in the right
and left AIMS cabinets. If software
part numbers HNP5C-AL01-1007,
HNP5D-AL02-1014, HNP5A-AL03-
1012, HNP59-AL04-1007, HNP5F-
AL05-1011, HNP5B-AL06-1007 and
HNP55-AD07-1011 or later ap-
proved software part numbers are
not shown as installed in the right
and left AIMS cabinets, do correc-
tive action(s) until the software part
numbers are shown as installed in
the right and left AIMS cabinets.
PART 2: Left Airplane In-
formation Management
System Cabinet Software
Installation and Software
Configuration Check.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 19, 2021
777-31A0342 RB
17 of 20
REQUIREMENTS BULLETIN 777-31A0342
ALERTALERT

### Page 18

Group 4:
Table 2: Airplane Information Management System Software Installation
Refer to the listed pro-
cedures in SB 777-
31A0342 Original Issue
or later approved revi-
sions as an accepted
procedure.
Method of
Compliance
ActionCondition
PART 1: Right Airplane
Information Management
System Cabinet Software
Installation and Software
Configuration Check.
-ACTION 1: Install the Airplane Infor-
mation Management System 2
(AIMS-2) Block Point (BP) Version
17C software part numbers
HNP5C-AL01-1007, HNP5D-AL02-
1014, HNP5A-AL03-1012, HNP59-
AL04-1007, HNP5F-AL05-1011,
HNP5B-AL06-1007 and HNP55-
AD07-1011 or later approved soft-
ware part numbers in the right
AIMS cabinet.
All Airplanes
PART 2: Left Airplane In-
formation Management
System Cabinet Software
Installation and Software
Configuration Check.
-ACTION 2: Install the AIMS-2 BP
V17C software part numbers
HNP5C-AL01-1007, HNP5D-AL02-
1014, HNP5A-AL03-1012, HNP59-
AL04-1007, HNP5F-AL05-1011,
HNP5B-AL06-1007 and HNP55-
AD07-1011 or later approved soft-
ware part numbers in the left AIMS
cabinet.
PART 1: Right Airplane
Information Management
System Cabinet Software
Installation and Software
Configuration Check.
-ACTION 3: Do a software configu-
ration check and make sure that
software part numbers HNP5C-
AL01-1007, HNP5D-AL02-1014,
HNP5A-AL03-1012, HNP59-AL04-
1007, HNP5F-AL05-1011, HNP5B-
AL06-1007 and HNP55-AD07-1011
or later approved software part
numbers are installed in the right
and left AIMS cabinets. If software
part numbers HNP5C-AL01-1007,
HNP5D-AL02-1014, HNP5A-AL03-
1012, HNP59-AL04-1007, HNP5F-
AL05-1011, HNP5B-AL06-1007 and
HNP55-AD07-1011 or later ap-
proved software part numbers are
not shown as installed in the right
and left AIMS cabinets, do correc-
tive action(s) until the software part
numbers are shown as installed in
the right and left AIMS cabinets.
PART 2: Left Airplane In-
formation Management
System Cabinet Software
Installation and Software
Configuration Check
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 19, 2021
777-31A0342 RB
18 of 20
REQUIREMENTS BULLETIN 777-31A0342
ALERTALERT

### Page 19

Group 5:
Table 3: Airplane Information Management System Software Installation
Refer to the listed pro-
cedures in SB 777-
31A0342 Original Issue
or later approved revi-
sions as an accepted
procedure.
Method of
Compliance
ActionCondition
Airplanes are required to
follow the load instruc-
tions concurrent with the
AIMS-2 hardware up-
grade. For airplanes in an
AIMS 1 configuration,
please submit a Request
for Proposal to Airplane-
Services@boeing.comfor
information on upgrading
to an AIMS 2 configura-
tion.
-ACTION 1: Contact The Boeing
Company for instructions for upgrad-
ing to AIMS-2 configurations and
do as instructed by Boeing.
All Airplanes
PART 1: Right Airplane
Information Management
System Cabinet Software
Installation and Software
Configuration Check.
-ACTION 2: Install the AIMS-2 Block
Point (BP) Version 17C software
part numbers HNP5C-AL01-1007,
HNP5D-AL02-1014, HNP5A-AL03-
1012, HNP59-AL04-1007, HNP5F-
AL05-1011, HNP5B-AL06-1007 and
HNP55-AD07-1011 or later ap-
proved software part numbers in
the right AIMS cabinet.
PART 2: Left Airplane In-
formation Management
System Cabinet Software
Installation and Software
Configuration Check.
-ACTION 3: Install the AIMS-2 BP
V17C software part numbers
HNP5C-AL01-1007, HNP5D-AL02-
1014, HNP5A-AL03-1012, HNP59-
AL04-1007, HNP5F-AL05-1011,
HNP5B-AL06-1007 and HNP55-
AD07-1011 or later approved soft-
ware part numbers in the left AIMS
cabinet.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 19, 2021
777-31A0342 RB
19 of 20
REQUIREMENTS BULLETIN 777-31A0342
ALERTALERT

### Page 20

Group 5:
Table 3: Airplane Information Management System Software Installation
Refer to the listed pro-
cedures in SB 777-
31A0342 Original Issue
or later approved revi-
sions as an accepted
procedure.
Method of
Compliance
ActionCondition
PART 1: Right Airplane
Information Management
System Cabinet Software
Installation and Software
Configuration Check.
-ACTION 4: Do a software configu-
ration check and make sure that
software part numbers HNP5C-
AL01-1007, HNP5D-AL02-1014,
HNP5A-AL03-1012, HNP59-AL04-
1007, HNP5F-AL05-1011, HNP5B-
AL06-1007 and HNP55-AD07-1011
or later approved software part
numbers are installed in the right
and left AIMS cabinets. If software
part numbers HNP5C-AL01-1007,
HNP5D-AL02-1014, HNP5A-AL03-
1012, HNP59-AL04-1007, HNP5F-
AL05-1011, HNP5B-AL06-1007 and
HNP55-AD07-1011 or later ap-
proved software part numbers are
not shown as installed in the right
and left AIMS cabinets, do correc-
tive action(s) until the software part
numbers are shown as installed in
the right and left AIMS cabinets.
PART 2: Left Airplane In-
formation Management
System Cabinet Software
Installation and Software
Configuration Check.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 19, 2021
777-31A0342 RB
20 of 20
REQUIREMENTS BULLETIN 777-31A0342
ALERTALERT

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.