# Boeing Special Attention Requirements Bulletin 777-33-0069 RB: No revision named, part 1 of 2

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2025-0348; AD 2026-05-15 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Special Attention Requirements Bulletin 777-33-0069 RB](https://openairdocs.org/service-documents/boeing/777-33-0069-rb.md)
- Title as filed: 777-33-0069 RB_Part1
- Pages: 25
- PDF: https://openairdocs.org/files/sha256/b2/9c/b29c94e8fa37c35b6facd571028c72b4028196726e7e1c1a60efb4f8d4a9fee0
- Page: https://openairdocs.org/service-documents/boeing/777-33-0069-rb/file/b29c94e8fa37

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Commercial 
Airplanes 
777 
Requirements Bulletin 
SPECIAL ATTENTION 
 
Number: 777-33-0069 RB 
Original Issue: October 15, 2024 
ATA System: 3320 
 
SUBJECT: LIGHTS - Passenger Compartment Lights - Sidewall Lights Inspection and Change 
 
EXPORT CONTROLLED - This technology or software is subject to the U.S. Export Administration Regulations 
(EAR), (15 C.F.R. Parts 730-774). No authorization from the U.S. Department of Commerce is required for 
export, re-export, in-country transfer, or access EXCEPT to country group E:1 or E:2 countries/persons per 
Supp.1 to Part 740 of the EAR. 
ECCN: 9E991 
 
Copyright © 2024 The Boeing Company 
 
Treatment of this document and its content is governed by contract with Boeing. Rights to use this document 
are licensed on a per aircraft basis and such rights may not be transferable. For more information, contact The 
Boeing Company. 
Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner, 
BBJ, DC-8, DC-9, DC-10, KC-10, KC-46, KDC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8, Poseidon and 
Boeing liveries are all trademarks owned by The Boeing Company; and no trademark license is granted in 
connection with this document unless provided in writing by Boeing. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Original Issue: October 15, 2024  
 
 
2.0 
 
777-33-0069 RB 
1 of 36

### Page 2

REQUIREMENTS BULLETIN 777-33-0069 
2 of 36 See page 1 for details 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
BLANK PAGE 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Original Issue: October 15, 2024 
 
 
Export Controlled ECCN: 9E991 
 
777-33-0069 RB

### Page 3

3 of 36 See page 1 for details 
 
 
REQUIREMENTS BULLETIN 777-33-0069 
 
 
Table of Contents 
1. EFFECTIVITY .............................................................................................................................................. 5 
A. Airplanes ............................................................................................................................................. 5 
B. Spares Affected .................................................................................................................................. 7 
2. CONCURRENT REQUIREMENTS ............................................................................................................. 7 
3. COMPLIANCE ............................................................................................................................................. 7 
4. APPROVAL ................................................................................................................................................. 8 
5. ACCOMPLISHMENT INSTRUCTIONS .................................................................................................... 11 
A. General Information .......................................................................................................................... 11 
B. Work Instructions .............................................................................................................................. 12 
FIGURE 1: PASSENGER COMPARTMENT - SIDEWALL LIGHT POWER CONNECTOR WIRE BUNDLE 
- INSPECTION ......................................................................................................................... 17 
FIGURE 2: PASSENGER COMPARTMENT - SIDEWALL LIGHT CLIP AND RINGPOST NOT AT 
EXPANSION JOINT LOCATIONS - INSTALLATION ............................................................... 19 
FIGURE 3: PASSENGER COMPARTMENT - SIDEWALL LIGHT CLIP AND RINGPOST AT EXPANSION 
JOINT LOCATIONS - INSTALLATION .................................................................................... 22 
FIGURE 4: PASSENGER COMPARTMENT - SIDEWALL LIGHT BRACKET AND RINGPOST - 
INSTALLATION [Group 1-4, 6, 8] ............................................................................................ 25 
FIGURE 5: PASSENGER COMPARTMENT - SIDEWALL LIGHT BRACKET AND RINGPOST AT STA 554 
- INSTALLATION [Group 5] ..................................................................................................... 28 
FIGURE 6: PASSENGER COMPARTMENT - SIDEWALL LIGHT BRACKET AND RINGPOST - 
INSTALLATION [Group 5, 7] .................................................................................................... 31 
FIGURE 7: PASSENGER COMPARTMENT - SIDEWALL LIGHT CLIP AND RINGPOST AT STA 478 - 
INSTALLATION [Group 7] ........................................................................................................ 34 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Original Issue: October 15, 2024 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Export Controlled ECCN: 9E991 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
777-33-0069 RB

### Page 4

REQUIREMENTS BULLETIN 777-33-0069 
4 of 36 See page 1 for details 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
BLANK PAGE 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Original Issue: October 15, 2024 
 
 
Export Controlled ECCN: 9E991 
 
777-33-0069 RB

### Page 5

5 of 36 See page 1 for details 
 
 
Commercial 
Airplanes 
777 
Requirements Bulletin 
SPECIAL ATTENTION 
 
Number: 777-33-0069 RB 
Original Issue: October 15, 2024 
ATA System: 3320 
 
SUBJECT: LIGHTS - Passenger Compartment Lights - Sidewall Lights Inspection and Change 
 
BOEING RECOMMENDS THAT EACH OPERATOR EXAMINE THIS DOCUMENT IMMEDIATELY. THIS IS 
AN ENHANCED REQUIRED FOR COMPLIANCE DOCUMENT. THE BOEING PROCESSES USED TO CREATE 
THE SERVICE BULLETIN (SB) AND THE REQUIREMENTS BULLETIN (RB) ENSURE THAT THE 
INFORMATION BETWEEN "RC START" AND "RC END" IN THE SB ARE IDENTICAL TO THE INFORMATION 
IN THE SAME SECTIONS (COMPLIANCE, WORK INSTRUCTIONS…) OF THE RB WHICH THE SB REFERS 
TO AS THE RELATED DOCUMENT. 
 
1. Effectivity 
 
A. Airplanes 
This bulletin is applicable to 777-200LR, 777-300ER Airplane(s), line number(s) 654, 662, 677, 
688, 725, 739, 741, 747, 757, 775, 1104, 1121, 1124, 1136, 1141, 1148, 1166, 1173, 1179, 1181, 
1184-1185, 1187, 1189-1191, 1194, 1196, 1198-1200, 1202, 1205-1206, 1209, 1213-1219, 
1222-1224, 1226-1229, 1231-1233, 1237, 1239-1241, 1244-1247, 1250-1251, 1253-1257, 
1259-1260, 1262-1263, 1265-1267, 1269-1270, 1273, 1275, 1277, 1279, 1281-1283, 1285-1289, 
1291, 1293-1296, 1299-1305, 1307, 1309-1311, 1313-1315, 1317, 1319, 1321-1325, 1327, 1329, 
1331-1333, 1335, 1337-1341, 1344-1345, 1347-1353, 1355-1369, 1371-1373, 1375, 1377-1379, 
1381, 1383-1384, 1386-1391, 1394-1405, 1407-1409, 1411-1421, 1423-1429, 1431, 1433-1437, 
1439, 14 41- 1442, 1444-1446, 1448-1453, 1456-1463, 1465-1471, 1474-1519, 1523, 1525, 1527, 
1529-1530, 1533, 1537-1545, 1547-1550, 1552-1556, 1558-1565, 1569, 1572, 1577, 1580, 1586, 
1590, 1593, 1595, 1597-1598, 1600, 1602, 1607, 1609, 1613, 1618, 1627, 1630-1631, 1634, 
1636-1637, 1639, 1641, 1643, 1648, 1652, 1654, 1667, 1671, 1675, 1678, 1683, 1687, 1690-1691, 
1695 in 8 Group(s). Where the effectivity is presented with hyphens between line numbers, the 
airplane applicability means "through" and "inclusive", e.g. line numbers 1-9 means line numbers 
1 through 9 inclusive. 
 
The Variable Numbers and Group Information for the applicable airplanes is given below. 
 
GROUP CONFIGURATION DESCRIPTION 
1 - 777-200LR and 777-300ER Airplanes that require sidewall lighting 
wire support inspection and change at up to 20 locations. 
2 - 777-300ER Airplanes that require sidewall lighting wire support 
inspection and change at up to 30 locations. 
 
 
 
 
 
Original Issue: October 15, 2024 
 
 
Export Controlled ECCN: 9E991 
 
777-33-0069 RB

### Page 6

REQUIREMENTS BULLETIN 777-33-0069 
6 of 36 See page 1 for details 
 
 
Variable Numb er Group 
WD046 - WD055 3 
WD121 - WD123 1 
WD895 - WD910 6 
WD933 - WD935 4 
WE005 - WE007 3 
WE056 - WE057 6 
WE138 - WE140 8 
WE141 - WE144 7 
WE147 - WE150 6 
WE168 - WE170 4 
WE171 - WE175 6 
WE178 4 
WE245 - WE250 1 
WE291 - WE298 5 
WE312 - WE320 4 
WE337 - WE350 4 
 
Variable Number Group 
WE366 - WE368 6 
WE396 - WE411 6 
WE426 - WE427 2 
WE428 - WE431 4 
WE436 - WE437 2 
WE438 - WE440 4 
WE441 - WE446 1 
WE451 - WE484 4 
WE486 - WE493 8 
WE495 - WE499 6 
WE501 - WE504 4 
WE511 - WE516 4 
WE526 - WE528 2 
WE536 - WE543 8 
WE544 - WE549 6 
WE560 - WE565 4 
 
Variable Number Group 
WE576 - WE587 4 
WE591 8 
WE601 - WE605 1 
WE626 - WE627 4 
WE641 - WE642 6 
WE651 - WE661 4 
WE666 - WE677 4 
WE681 - WE683 3 
WE684 - WE689 4 
WE701 - WE705 4 
WE711 - WE712 4 
WE731 - WE732 6 
WE736 - WE740 4 
WE746 - WE772 4 
WE776 - WE786 4 
WE791 - WE792 4 
 
 
 
GROUP CONFIGURATION DESCRIPTION 
3 - 777-200LR and 777-300ER Airplanes that require sidewall lighting 
wire support inspection and change at up to 54 locations. 
4 - 777-300ER Airplanes that require sidewall lighting wire support 
inspection and change at up to 61 locations. 
5 - 777-300ER Airplanes that require sidewall lighting wire support 
inspection and change with brackets up to 51 locations. 
6 - 777-300ER Airplanes that require sidewall lighting wire support 
inspection and change with brackets up to 64 locations. 
7 - 777-300ER Airplanes that require sidewall lighting wire support 
inspection and change with brackets up to 62 locations. 
8 - 777-300ER Airplanes that require sidewall lighting wire support 
inspection and change with brackets up to 68 locations. 
 
 
Airplane Models: 
 
777-200LR, 777-300ER 
 
 
 
Original Issue: October 15, 2024 
 
 
Export Controlled ECCN: 9E991 
 
777-33-0069 RB

### Page 7

REQUIREMENTS BULLETIN 777-33-0069 
7 of 36 See page 1 for details 
 
 
 
 
   
B. Spares Affected 
None. 
 
2. CONCURRENT REQUIREMENTS 
 
None. 
 
3. COMPLIANCE 
 
The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to 
Requirements Bulletin 777-33-0069 RB. The Airworthiness Directive will make the compliance tasks and 
times given in Requirements Bulletin 777-33-0069 RB mandatory. 
 
Accomplish the required action(s), based on the applicable condition(s) in Table(s) 1, in accordance with 
Accomplishment Instructions. 
 
When more than one OPTION is given for a CONDITION, do only one of the OPTION numbers. When 
more than one ACTION is given for a CONDITION or an OPTION, do all of the ACTION numbers for that 
CONDITION or OPTION. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Original Issue: October 15, 2024 
 
 
Export Controlled ECCN: 9E991 
 
777-33-0069 RB 
Variable Numb er Group 
WE801 - WE806 4 
WE811 - WE812 4 
WE826 - WE828 4 
 
Variable Number Group 
WE831 - WE835 6 
WE851 - WE853 6 
WE856 - WE857 6 
 
Variable Number Group 
WE861 - WE863 8 
WE866 - WE868 6 
WE871 8

### Page 8

REQUIREMENTS BULLETIN 777-33-0069 
8 of 36 See page 1 for details 
 
 
 
 
Table 1: Forward and Aft Sidewall Lights Inspection and Change 
 
Condition Action Boeing Recommended 
Compliance Time 
Repeat Interval 
(Not to Exceed) 
All Airplanes Do a General Visual Inspection (GVI) of 
sidewall light part numbers 1J5011-200135- 
(), 1J5011-200142-() and 1J5011-200156-() 
for wire chafing damage. 
Within 36 months after 
the Original Issue date of 
Requirements Bulletin 
777-33-0069 RB. 
 
CONDITION 1: 
NO WIRE 
CHAFING DAM- 
AGE FOUND 
ACTION 1: At locations where sidewall light 
part numbers 1J5011-200135-(), 1J5011- 
200142-() and 1J5011-200156-() are in- 
stalled aft of STA 550, adjust wire routing 
and install new wire support clip, ringpost 
and clamp. 
Before further flight. - 
ACTION 2: At locations where sidewall light 
part numbers 1J5011-200135-(), 1J5011- 
200142-() and 1J5011-200156-() are in- 
stalled forward of STA 550, adjust wire rout- 
ing and install new wire support bracket, 
ringpost and clamp. 
- 
CONDITION 2: 
ANY WIRE 
CHAFING DAM- 
AGE FOUND 
OPTION 1 (ACTION 1): At affected sidewall 
light location, repair the wire chafing dam- 
age. 
Before further flight. - 
OPTION 2 (ACTION 1): At affected sidewall 
light location, replace the light with a new or 
serviceable light. (a) 
- 
OPTION 1 (ACTION 2) and OPTION 2 (AC- 
TION 2): At locations where sidewall light 
part numbers 1J5011-200135-(), 1J5011- 
200142-() and 1J5011-200156-() are in- 
stalled aft of STA 550, adjust wire routing 
and install new wire support clip, ringpost 
and clamp. 
- 
OPTION 1 (ACTION 3) and OPTION 2 (AC- 
TION 3): At locations where sidewall light 
part numbers 1J5011-200135-(), 1J5011- 
200142-() and 1J5011-200156-() are in- 
stalled forward of STA 550, adjust wire rout- 
ing and install new wire support bracket, 
ringpost and clamp. 
- 
(a) A serviceable light is defined as a light that needs no visible repairs and functions as intended. 
4. APPROVAL 
 
This Requirements Bulletin was examined by the Federal Aviation Administration (FAA). The changes 
specified in this document comply with the applicable regulations and are FAA approved, as well as European 
Union Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved 
airplanes listed in this Requirements Bulletin effectivity. This document and its approval were based on the 
 
 
Original Issue: October 15, 2024 
 
 
Export Controlled ECCN: 9E991 
 
777-33-0069 RB

### Page 9

REQUIREMENTS BULLETIN 777-33-0069 
9 of 36 See page 1 for details 
 
 
 
 
airplane in its original Boeing delivery configuration or as modified by other Boeing changes. 
 
If an airplane has a non-Boeing modification or repair that affects a component or system also affected by 
this Requirements Bulletin, the operator is responsible for obtaining appropriate regulatory agency approval 
before incorporating this Requirements Bulletin. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Original Issue: October 15, 2024 
 
 
Export Controlled ECCN: 9E991 
 
777-33-0069 RB

### Page 10

REQUIREMENTS BULLETIN 777-33-0069 
10 of 
 
See page 1 for details 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
BLANK PAGE 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Original Issue: October 15, 2024 
 
 
Export Controlled ECCN: 9E991 
 
777-33-0069 RB

### Page 11

REQUIREMENTS BULLETIN 777-33-0069 
11 of 36 See page 1 for details 
 
 
 
 
5. ACCOMPLISHMENT INSTRUCTIONS 
 
A. GENERAL INFORMATION 
 
NOTE: 1. This is an Enhanced Required for Compliance document. There will be a separate 
Service Bulletin (SB) and a separate Requirements Bulletin (RB). If an RB is mandated 
by an Airworthiness Directive (AD), then all applicable requirements specified in the 
RB must be done. In the RB, the "Refer to the listed procedures..." column of the 
table(s) in the Work Instructions is for reference only. The procedures in that column 
are not required by the AD and are for guidance only. For the related SB, some 
locations are marked RC Start and RC End to identify the requirements that are 
restated from the RB. For the related SB, the areas between RC Start and RC End, 
including sub-steps and any figures identified between RC Start and RC End, must 
be done to comply with the AD. Therefore, an Alternative Method of Compliance 
(AMOC) is required for any deviations to steps between RC Start and RC End, 
including substeps and identified figures. For the related SB, the steps not between 
RC Start and RC End may be deviated from using accepted methods in accordance 
with the operator's maintenance or inspection program without obtaining approval 
of an AMOC; this is provided that the steps between RC Start and RC End, including 
sub-steps and identified figures, can still be done as specified, and the airplane can 
be put back in an airworthy condition. Figures not required for compliance are omitted 
from the RB. 
 
2. This is an Enhanced Required for Compliance document. The Boeing processes 
used to create the Service Bulletin (SB) and the Requirements Bulletin (RB) ensure 
that the information between "RC Start" and "RC End" in the SB are identical to the 
information in the same sections (Compliance, Work Instructions...) of the RB which 
the SB refers to as the related document. 
 
3. The compliance times for the actions in WORK INSTRUCTIONS are in Compliance. 
 
4. These work instructions refer to procedures included in other Boeing documents. 
When the words "refer to" are used and the operator has an accepted alternative 
procedure, the accepted alternative procedure can be used. When the words "in 
accordance with" are included in the instruction, the procedure in the Boeing document 
must be used. 
 
5. Where the work instructions include installation of a kept part, a new or serviceable 
part with the same part number can be installed as an alternative to the kept part.  
 
6. If it is necessary to remove more parts for access, you can remove those parts. If 
you can get access without removing identified parts, it is not necessary to remove 
all of the identified parts. Jacking and shoring limitations must be observed. 
 
7. A General Visual Inspection (GVI) is defined as: A visual examination of an interior 
or exterior area, installation or assembly to detect obvious damage, failure or 
irregularity. This level of inspection is made from within touching distance, unless 
otherwise specified. A mirror may be necessary to enhance visual access to all 
exposed surfaces in the inspection area. This level of inspection is made under 
normally available lighting conditions such as daylight, hangar lighting, flashlight or 
drop-light and may require removal or opening of access panels or doors. Stands, 
ladders or platforms may be required to gain proximity to the area being checked. 
Basic cleaning may be required to ensure appropriate visibility. 
 
Original Issue: October 15, 2024 
 
 
Export Controlled ECCN: 9E991 
 
777-33-0069 RB

### Page 12

REQUIREMENTS BULLETIN 777-33-0069 
12 of 
 
See page 1 for details 
 
 
 
 
8. When more than one OPTION is given for a CONDITION, do only one of the OPTION 
numbers. When more than one ACTION is given for a CONDITION or an OPTION, 
do all of the ACTION numbers for that CONDITION or OPTION. 
 
9. Use of colors in Figures is based on guidance from the ATA e-Business Program 
(ATA) iSpec 2200. 
 
10. Refer to the SWPM 20-10-11 and SWPM 20-10-12 for the wire installation procedures, 
and SWPM 20-10-19 for the wire separation requirements, as accepted procedures. 
 
11. If the length of any fastener specified in this service bulletin does not meet installation 
standards given in SRM Chapter 51, then a fastener of the same specification, or 
an approved substitute, with a length which meets the installation standards given 
in SRM Chapter 51 may be used. In addition, washers may be installed for fastener 
grip length in accordance with SRM Chapter 51. Refer to SOPM 20-50-01 for alternate 
full threaded fasteners (screws) needed for installation in this service bulletin.  
 
B. WORK INSTRUCTIONS 
 
Actions Required for Compliance 
 
1. Requirements: 
 
Group 1-4, 6, 8: 
Table 1: Forward and Aft Sidewall Lights Inspection and Change. 
 
Condition Action Method of Compliance Refer to the listed pro- 
cedures in SB 777-33- 
0069 Original Issue or 
later approved revi- 
sions as an accepted 
procedure. 
All Airplanes Do a General Visual Inspection 
(GVI) of sidewall light part numbers 
1J5011-200135-(), 1J5011-200142- 
() and 1J5011-200156-() for wire 
chafing damage. 
- PART 1: OPEN ACCESS 
FIGURE 1 - 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Original Issue: October 15, 2024 
 
 
Export Controlled ECCN: 9E991 
 
777-33-0069 RB

### Page 13

REQUIREMENTS BULLETIN 777-33-0069 
13 of 36 See page 1 for details 
 
 
 
 
Group 1-4, 6, 8: 
Table 1: Forward and Aft Sidewall Lights Inspection and Change. 
 
Condition Action Method of Compliance Refer to the listed pro- 
cedures in SB 777-33- 
0069 Original Issue or 
later approved revi- 
sions as an accepted 
procedure. 
CONDITION 1: 
NO WIRE CHAF- 
ING DAMAGE 
FOUND 
ACTION 1: At locations where side- 
wall light part numbers 1J5011- 
200135-(), 1J5011-200142-() and 
1J5011-200156-() are installed aft 
of STA 550, adjust wire routing and 
install new wire support clip, ringpost 
and clamp. 
FIGURE 2 and FIGURE 3 - 
ACTION 2: At locations where side- 
wall light part numbers 1J5011- 
200135-(), 1J5011-200142-() and 
1J5011-200156-() are installed for- 
ward of STA 550, adjust wire routing 
and install new wire support bracket, 
ringpost and clamp. 
FIGURE 4 - 
- PART 2: TEST 
- PART 3: CLOSE AC- 
CESS 
CONDITION 2: 
ANY WIRE CHAF- 
ING DAMAGE 
FOUND 
OPTION 1 (ACTION 1) : At affected 
sidewall light location, repair the wire 
chafing damage. 
- PART 4: SIDEWALL 
LIGHT POWER CON- 
NECTOR WIRE BUN- 
DLE REPAIR 
OPTION 2 (ACTION 1) : At affected 
sidewall light location, replace the 
light with a new or serviceable light. 
(a) 
- PART 5: SIDEWALL 
LIGHT REPLACEMENT 
OPTION 1 (ACTION 2) and OPTION 
2 (ACTION 2): At locations where 
sidewall light part numbers 1J5011- 
200135-(), 1J5011-200142-() and 
1J5011-200156-() are installed aft 
of STA 550, adjust wire routing and 
install new wire support clip, ringpost 
and clamp. 
FIGURE 2 and FIGURE 3 - 
OPTION 1 (ACTION 3) and OPTION 
2 (ACTION 3): At locations where 
sidewall light part numbers 1J5011- 
200135-(), 1J5011-200142-() and 
1J5011-200156-() are installed for- 
ward of STA 550, adjust wire routing 
and install new wire support bracket, 
ringpost and clamp. 
FIGURE 4 - 
- PART 2: TEST 
- PART 3: CLOSE AC- 
CESS 
(a) A serviceable light is defined as a light that needs no visible repairs and functions as intended. 
 
 
Original Issue: October 15, 2024 
 
 
Export Controlled ECCN: 9E991 
 
777-33-0069 RB

### Page 14

REQUIREMENTS BULLETIN 777-33-0069 
14 of 
 
See page 1 for details 
 
 
 
 
Group 5: 
Table 2: Forward and Aft Sidewall Lights Inspection and Change. 
 
Condition Action Method of Compliance Refer to the listed proce- 
dures in SB 777-33-0069 
Original Issue or later 
approved revisions as an 
accepted procedure. 
All Airplanes Do a General Visual Inspection 
(GVI) of sidewall light part numbers 
1J5011-200135-(), 1J5011-200142- 
() and 1J5011-200156-() for wire 
chafing damage. 
- PART 6: OPEN ACCESS 
FIGURE 1 - 
CONDITION 1: 
NO WIRE 
CHAFING 
DAMAGE 
FOUND 
ACTION 1: At locations where side- 
wall light part numbers 1J5011- 
200135-(), 1J5011-200142-() and 
1J5011-200156-() are installed aft 
of STA 550, adjust wire routing and 
install new wire support clip, ringpost 
and clamp. 
FIGURE 2 and FIGURE 3 - 
ACTION 2: At locations where side- 
wall light part numbers 1J5011- 
200135-(), 1J5011-200142-() and 
1J5011-200156-() are installed for- 
ward of STA 550, adjust wire routing 
and install new wire support bracket, 
ringpost and clamp. 
FIGURE 5 and FIGURE 6 - 
- PART 2: TEST 
- PART 3: CLOSE ACCESS 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Original Issue: October 15, 2024 
 
 
Export Controlled ECCN: 9E991 
 
777-33-0069 RB

### Page 15

REQUIREMENTS BULLETIN 777-33-0069 
15 of 36 See page 1 for details 
 
 
 
 
Group 5: 
Table 2: Forward and Aft Sidewall Lights Inspection and Change. 
 
Condition Action Method of Compliance Refer to the listed proce- 
dures in SB 777-33-0069 
Original Issue or later 
approved revisions as an 
accepted procedure. 
CONDITION 2: 
ANY WIRE 
CHAFING 
DAMAGE 
FOUND 
OPTION 1 (ACTION 1) : At affected 
sidewall light location, repair the wire 
chafing damage. 
- PART 4: SIDEWALL 
LIGHT POWER CONNEC- 
TOR WIRE BUNDLE RE- 
PAIR 
OPTION 2 (ACTION 1) : At affected 
sidewall light location, replace the 
light with a new or serviceable light. 
(a) 
- PART 5: SIDEWALL 
LIGHT REPLACEMENT 
OPTION 1 (ACTION 2) and OPTION 
2 (ACTION 2): At locations where 
sidewall light part numbers 1J5011- 
200135-(), 1J5011-200142-() and 
1J5011-200156-() are installed aft 
of STA 550, adjust wire routing and 
install new wire support clip, ringpost 
and clamp. 
FIGURE 2 and FIGURE 3 - 
OPTION 1 (ACTION 3) and OPTION 
2 (ACTION 3): At locations where 
sidewall light part numbers 1J5011- 
200135-(), 1J5011-200142-() and 
1J5011-200156-() are installed for- 
ward of STA 550, adjust wire routing 
and install new wire support bracket, 
ringpost and clamp. 
FIGURE 5 and FIGURE 6 - 
- PART 2: TEST 
- PART 3: CLOSE ACCESS 
(a) A serviceable light is defined as a light that needs no visible repairs and functions as intended. 
Group 7: 
Table 3: Forward and Aft Sidewall Lights Inspection and Change. 
 
Condition Action Method of Compliance Refer to the listed proce- 
dures in SB 777-33-0069 
Original Issue or later 
approved revisions as an 
accepted procedure. 
All Airplanes Do a General Visual Inspection 
(GVI) of sidewall light part numbers 
1J5011-200135-(), 1J5011-200142- 
() and 1J5011-200156-() for wire 
chafing damage. 
- PART 6: OPEN ACCESS 
FIGURE 1 - 
 
 
 
Original Issue: October 15, 2024 
 
 
Export Controlled ECCN: 9E991 
 
777-33-0069 RB

### Page 16

REQUIREMENTS BULLETIN 777-33-0069 
16 of 
 
See page 1 for details 
 
 
 
 
Group 7: 
Table 3: Forward and Aft Sidewall Lights Inspection and Change. 
 
Condition Action Method of Compliance Refer to the listed proce- 
dures in SB 777-33-0069 
Original Issue or later 
approved revisions as an 
accepted procedure. 
CONDITION 1: 
NO WIRE 
CHAFING 
DAMAGE 
FOUND 
ACTION 1: At locations where side- 
wall light part numbers 1J5011- 
200135-(), 1J5011-200142-() and 
1J5011-200156-() are installed aft 
of STA 550, adjust wire routing and 
install new wire support clip, ringpost 
and clamp. 
FIGURE 2, FIGURE 3 and 
FIGURE 7(b) 
- 
ACTION 2: At locations where side- 
wall light part numbers 1J5011- 
200135-(), 1J5011-200142-() and 
1J5011-200156-() are installed for- 
ward of STA 550, adjust wire routing 
and install new wire support bracket, 
ringpost and clamp. 
FIGURE 6 - 
- PART 2: TEST 
- PART 3: CLOSE ACCESS 
CONDITION 2: 
ANY WIRE 
CHAFING 
DAMAGE 
FOUND 
OPTION 1 (ACTION 1) : At affected 
sidewall light location, repair the wire 
chafing damage. 
- PART 4: SIDEWALL 
LIGHT POWER CONNEC- 
TOR WIRE BUNDLE RE- 
PAIR 
OPTION 2 (ACTION 1) : At affected 
sidewall light location, replace the 
light with a new or serviceable light. 
(a) 
- PART 5: SIDEWALL 
LIGHT REPLACEMENT 
OPTION 1 (ACTION 2) and OPTION 
2 (ACTION 2): At locations where 
sidewall light part numbers 1J5011- 
200135-(), 1J5011-200142-() and 
1J5011-200156-() are installed aft 
of STA 550, adjust wire routing and 
install new wire support clip, ringpost 
and clamp. 
FIGURE 2, FIGURE 3 and 
FIGURE 7(b) 
- 
OPTION 1 (ACTION 3) and OPTION 
2 (ACTION 3): At locations where 
sidewall light part numbers 1J5011- 
200135-(), 1J5011-200142-() and 
1J5011-200156-() are installed for- 
ward of STA 550, adjust wire routing 
and install new wire support bracket, 
ringpost and clamp. 
FIGURE 6 - 
- PART 2: TEST 
- PART 3: CLOSE ACCESS 
(a) A serviceable light is defined as a light that needs no visible repairs and functions as intended. 
(b) Figure 7 is for STA 478, but will be installing new wire support clip, ringpost and clamp. 
 
Original Issue: October 15, 2024 
 
 
Export Controlled ECCN: 9E991 
 
777-33-0069 RB

### Page 17 (OCR)

REQUIREMENTS BULLETIN 777-33-0069
SIDEWALL
LIGHT
PASSENGER COMPARTMENT
(VIEW LOOKING FORWARD)
(TYPICAL)
LIGHT
TYPICAL
INSPECTION AREA  3063432
The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for each sidewall light location.
FIGURE 1: PASSENGER COMPARTMENT - SIDEWALL LIGHT POWER CONNECTOR WIRE BUNDLE -
INSPECTION
(SHEET 1 OF 2)
Original Issue: October 15, 2024
-xport Controlled ECCN: 9E991  See page 1 for details  777-33-0069 RB  17 of 36

### Page 18

REQUIREMENTS BULLETIN 777-33-0069 
18 of 
 
See page 1 for details 
 
 
 
 
Step Task Name Identification Qty More Data 
1 Inspect POWER CONNECTOR WIRE BUNDLE - - (a) 
(a) Do a General Visual Inspection of the sidewall light power connector wire bundle for chafing damage. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
FIGURE 1: PASSENGER COMPARTMENT - SIDEWALL LIGHT POWER CONNECTOR WIRE BUNDLE - 
INSPECTION 
(SHEET 2 OF 2) 
Original Issue: October 15, 2024  
 
Export Controlled ECCN: 9E991 
 
777-33-0069 RB

### Page 19 (OCR)

REQUIREMENTS BULLETIN 777-33-0069
SIDEWALL
LIGHT
PASSENGER COMPARTMENT
(VIEW LOOKING FORWARD)
(TYPICAL)
TYPICAL
3047671
FIGURE 2: PASSENGER COMPARTMENT - SIDEWALL LIGHT CLIP AND RINGPOST NOT AT EXPANSION
JOINT LOCATIONS - INSTALLATION
(SHEET 1 OF 3)
Original Issue: October 15, 2024
Exporte page 1 eccelai E991  777-33-0069 RB  19 0t 36

### Page 20

REQUIREMENTS BULLETIN 777-33-0069 
20 of 
 
See page 1 for details 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
FIGURE 2: PASSENGER COMPARTMENT - SIDEWALL LIGHT CLIP AND RINGPOST NOT AT EXPANSION 
JOINT LOCATIONS - INSTALLATION 
(SHEET 2 OF 3) 
Original Issue: October 15, 2024  
 
Export Controlled ECCN: 9E991 
 
777-33-0069 RB

### Page 21

REQUIREMENTS BULLETIN 777-33-0069 
21 of 36 See page 1 for details 
 
 
 
 
The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY 
numbers shown below are the number of parts necessary for each sidewall light location.  
 
Step Task Name Identification Qty More Data 
1 Apply ADHESIVE BMS5-105, TYPE II, 
CLASS 3 
- (a) 
2 Install (New) CLIP, BONDABLE DET 421W3351-1 1 - 
3 Install (New) RINGPOST, WIRE HARNESS 
MOUNTING SUPPORT 
BACS31H1A 1 (b) 
Install (New) SCREW BACS12GU3K29 1 (c) 
Install (New) NUT BACN10JC3CD 1 (c) 
4 Route POWER CONNECTOR WIRE 
BUNDLE 
- 1 (d) 
Install (New) STRAP BACS38W3 1 (b) 
(a) Apply to mating surfaces of clip and panel. Refer to SOPM 20-50-12 as an accepted procedure. 
(b) Refer to SWPM 20-10-12 as an accepted procedure. 
(c) Refer to SOPM 20-50-01 as an accepted procedure. 
(d) Refer to SWPM 20-10-11 as an accepted procedure. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
FIGURE 2: PASSENGER COMPARTMENT - SIDEWALL LIGHT CLIP AND RINGPOST NOT AT EXPANSION 
JOINT LOCATIONS - INSTALLATION 
(SHEET 3 OF 3) 
Original Issue: October 15, 2024  
 
Export Controlled ECCN: 9E991 
 
777-33-0069 RB

### Page 22 (OCR)

REQUIREMENTS BULLETIN 777-33-0069
SIDEWALI
- LIGH
PASSENGER COMPARTMENT
(VIEW LOOKING FORWARD)
(TYPICAL)
STA
554
1.00
MAX
VIEW LOOKING INBOARD
(TYPICAL)
FIGURE 3: PASSENGER COMPARTMENT - SIDEWALL LIGHT CLIP AND RINGPOST AT EXPANSION
JOINT LOCATIONS - INSTALLATION
(SHEET 1 OF 3)
Original Issue: October 15, 2024
777-33-0069 RB
Export Controlled ECCN: 9E991  See page 1 for details  22 of

### Page 23 (OCR)

REQUIREMENTS BULLETIN 777-33-0069
VIEW LOOKING OUTBOARD
(TYPICAL)
B
3067632
FIGURE 3: PASSENGER COMPARTMENT - SIDEWALL LIGHT CLIP AND RINGPOST AT EXPANSION
JOINT LOCATIONS - INSTALLATION
(SHEET 2 OF 3)
Original Issue: October 15, 2024
Export Controlled ECCN: 9E991  See page 1 for details  777-33-0069 RB  23 01 36

### Page 24

REQUIREMENTS BULLETIN 777-33-0069 
24 of 
 
See page 1 for details 
 
 
 
 
The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY 
numbers shown below are the number of parts necessary for each sidewall light location.  
 
Step Task Name Identification Qty More Data 
1 Apply ADHESIVE BMS5-105, TYPE II, 
CLASS 3 
- (a) 
2 Install (New) CLIP, BONDABLE DET 421W3351-1 1 - 
3 Install (New) RINGPOST, WIRE 
HARNESS MOUNTING 
SUPPORT 
BACS31H1A 1 (b) 
Install (New) SCREW BACS12GU3K29 1 (c) 
Install (New) NUT BACN10JC3CD 1 (c) 
4 Route POWER CONNECTOR 
WIRE BUNDLE 
- 1 (d) 
Adjust POWER CONNECTOR 
WIRE BUNDLE 
- 1 (e) 
Install (New) STRAP BACS38W3 1 (b) 
(a) Apply to mating surfaces of clip and panel. Refer to SOPM 20-50-12 as an accepted procedure. 
(b) Refer to SWPM 20-10-12 as an accepted procedure. 
(c) Refer to SOPM 20-50-01 as an accepted procedure. 
(d) Refer to SWPM 20-10-11 as an accepted procedure. 
(e) Make loop in POWER CONNECTOR WIRE BUNDLE for possible expansion. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
FIGURE 3: PASSENGER COMPARTMENT - SIDEWALL LIGHT CLIP AND RINGPOST AT EXPANSION 
JOINT LOCATIONS - INSTALLATION 
(SHEET 3 OF 3) 
Original Issue: October 15, 2024  
 
Export Controlled ECCN: 9E991 
 
777-33-0069 RB

### Page 25

REQUIREMENTS BULLETIN 777-33-0069 
25 of 36 See page 1 for details 
 
 
 
 
This Figure applies only to: Group 1-4, 6, 8. 
 
 
 
 
 
 
 
 
 
 
 
FIGURE 4: PASSENGER COMPARTMENT - SIDEWALL LIGHT BRACKET AND RINGPOST - INSTALLATION 
(SHEET 1 OF 3) 
Original Issue: October 15, 2024  
 
Export Controlled ECCN: 9E991 
 
777-33-0069 RB

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
