# Boeing Alert Service Bulletin 777-53A0054: Revision 1

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2012-0497; AD 2013-07-11 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Alert Service Bulletin 777-53A0054](https://openairdocs.org/service-documents/boeing/777-53a0054.md)
- Title as filed: U.S. DOT/FAA - Service Information
- Pages: 91
- PDF: https://openairdocs.org/files/sha256/7f/ba/7fba08d293892ae69c40a1f9c1856e04b99e344e3370cad29be9d33acef53918
- Page: https://openairdocs.org/service-documents/boeing/777-53a0054/file/7fba08d29389

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Commercial 
Airplanes
777
Service Bulletin
Number: 777-53A0054
Original Issue: August 07, 2008
Revision 1: November 04, 2010
ATA System: 5300
SUBJECT: FUSELAGE - Body Station 132.5 to Body Station 2150 - External Inspection of the
Fuselage Skin for External Scribe Lines
Export of this technology is controlled under the United States Export Administration Regulations (EAR) (15
CFR 730-774). An export license may be required before it is used for development, production or use by foreign
persons from specific countries. The controller of this data has the individual responsibility to abide by all export
laws.
9E991ECCN:
BOEING PROPRIETARY, CONFIDENTIAL, AND/OR TRADE SECRET
Copyright © 2008 The Boeing Company
Unpublished Work - All Rights Reserved
Boeing claims copyright in each page of this document only to the extent that the page contains copyrightable
subject matter. Boeing also claims copyright in this document as a compilation and/or collective work.
This document includes proprietary information owned by The Boeing Company and/or one or more third parties.
Treatment of the document and the information it contains is governed by contract with Boeing. For more
information, contact The Boeing Company, P.O. Box 3707, Seattle, Washington 98124.
Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner,
BBJ, DC-8, DC-9, DC-10, KC-10, KDC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8A, Poseidon and the
Boeing livery are all trademarks owned by The Boeing Company; and no trademark license is granted in
connection with this document unless provided in writing by Boeing.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: August 07, 2008
777-53A0054Revision 1: November 04, 2010
1 of 91
3.0

### Page 2

BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: August 07, 2008
777-53A0054Revision 1: November 04, 2010
2 of 91
BOEING SERVICE BULLETIN 777-53A0054
BLANK PAGE

### Page 3

Table of Contents
Revision Transmittal Sheet ............................................ 5
Summary ...................................................... 7
1. PLANNING INFORMATION ........................................ 9
A. Effectivity ................................................ 9
1. Airplanes ............................................. 9
2. Spares Affected ........................................ 1 2
B. Concurrent Requirements ...................................... 1 2
C. Reason ................................................ 1 2
D. Description .............................................. 1 3
E. Compliance .............................................. 1 4
F. Approval ............................................... 2 4
G. Manpower .............................................. 2 4
H. Weight and Balance Changes .................................... 2 7
I. Electrical Load Data ......................................... 2 8
J. References .............................................. 2 8
1. Existing Data .......................................... 2 8
2. Data supplied with this Service Bulletin ............................ 2 8
3. Installation Drawings Used in the Preparation of this Service Bulletin ............ 2 8
K. Publications Affected ........................................ 2 8
L. Interchangeability and Intermixability of Parts ........................... 2 8
2. MATERIAL INFORMATION ........................................ 2 9
A. Material - Price and Availability ................................... 2 9
B. Industry Support Information .................................... 2 9
C. Parts Necessary For Each Airplane ................................. 2 9
1. Kits/Parts ............................................ 2 9
2. Parts and Materials Supplied by the Operator ........................ 2 9
3. Parts Modified and Reidentified ................................ 2 9
4. Parts Removed and Not Replaced .............................. 2 9
D. Parts Necessary to Change Spares ................................. 2 9
E. Special Tooling - Price and Availability ............................... 2 9
F. Special Tooling Necessary to do this Service Bulletin ....................... 2 9
3. ACCOMPLISHMENT INSTRUCTIONS .................................. 3 1
A. GENERAL INFORMATION ..................................... 3 1
B. WORK INSTRUCTIONS ....................................... 3 3
FIGURE 1: EXTERNAL DOUBLER INSPECTION LOCATIONS - GROUP 1 AIRPLANES [Group 1] . 46
FIGURE 2: EXTERNAL DOUBLER INSPECTION LOCATIONS - GROUP 2 AIRPLANES [Group 2] . 47
FIGURE 3: EXTERNAL DOUBLER INSPECTION LOCATIONS - GROUP 3 AIRPLANES [Group 3] . 48
FIGURE 4: EXTERNAL DOUBLER INSPECTION LOCATIONS - GROUP 4 AIRPLANES [Group 4] . 49
FIGURE 5: ZONE 1 - GROUP 3 AND 4 AIRPLANES [Group 3-4] .................... 5 0
FIGURE 6: ZONE 2 - GROUP 1 AND 2 AIRPLANES [Group 1-2] .................... 5 1
FIGURE 7: ZONE 2 - GROUP 3 AND 4 AIRPLANES [Group 3-4] .................... 5 2
FIGURE 8: ZONE 3 - GROUP 1 AIRPLANES [Group 1] ......................... 5 3
FIGURE 9: ZONE 3 - GROUP 2 AIRPLANES [Group 2] ......................... 5 4
FIGURE 10: ZONE 3 - GROUP 3 AIRPLANES [Group 3] ......................... 5 5
FIGURE 11: ZONE 3 - GROUP 4 AIRPLANES [Group 4] ......................... 5 6
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: August 07, 2008
777-53A0054Revision 1: November 04, 2010
3 of 91
BOEING SERVICE BULLETIN 777-53A0054

### Page 4

FIGURE 12: ZONE 4 - GROUP 1 AND 2 AIRPLANES [Group 1-2] .................... 5 7
FIGURE 13: ZONE 4 - GROUP 3 AND 4 AIRPLANES [Group 3-4] .................... 5 8
FIGURE 14: INSPECTION FOR SCRIBE LINES AT EXTERNAL REPAIR DOUBLER LOCATIONS . . 59
FIGURE 15: INSPECTION FOR SCRIBE LINES AT LAP JOINT LOCATIONS .............. 6 0
FIGURE 16: INSPECTION FOR SCRIBE LINES AT BUTT JOINT LOCATIONS ............. 6 1
FIGURE 17: INSPECTION FOR SCRIBE LINES AROUND THE FORWARD LARGE CARGO DOOR HINGES
- GROUP 1 AND 3 AIRPLANES [Group 1, 3] ......................... 6 3
FIGURE 18: INSPECTION FOR SCRIBE LINES AROUND THE FORWARD AND AFT LARGE CARGO
DOOR HINGES - GROUP 2 AND 4 AIRPLANES [Group 2, 4] ............... 6 6
FIGURE 19: INSPECTION FOR CRACKS AT SCRIBE LINES AT EXTERNAL REPAIR DOUBLER
LOCATIONS OR AT LAP JOINT LOCATIONS ........................ 6 9
FIGURE 20: INSPECTION FOR CRACKS AT SCRIBE LINES AT BUTT JOINT LOCATIONS ..... 7 2
FIGURE 21: INSPECTION FOR CRACKS AT SCRIBE LINES AROUND THE FORWARD LARGE CARGO
DOOR HINGES - GROUP 1 AND 3 AIRPLANES [Group 1, 3] ............... 7 4
FIGURE 22: INSPECTION FOR CRACKS AT SCRIBE LINES AROUND THE FORWARD AND AFT LARGE
CARGO DOOR HINGES - GROUP 2 AND 4 AIRPLANES [Group 2, 4] ........... 7 8
APPENDIX A: SEALANT REMOVAL PROCEDURE FOR EXTERIOR PRESSURIZED FUSELAGE SKIN . 82
APPENDIX B: SCRIBE SAMPLE ....................................... 9 0
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: August 07, 2008
777-53A0054Revision 1: November 04, 2010
4 of 91
BOEING SERVICE BULLETIN 777-53A0054

### Page 5

Commercial 
Airplanes
777
Service Bulletin
Revision Transmittal SheetNumber: 777-53A0054Original Issue: August 07, 2008
Revision 1: November 04, 2010
ATA System: 5300
SUBJECT: FUSELAGE - Body Station 132.5 to Body Station 2150 - External Inspection of the
Fuselage Skin for External Scribe Lines
This revision includes all pages of the service bulletin.
COMPLIANCE INFORMATION RELATED TO THIS REVISION
More work is necessary on airplanes which have not been stripped or repainted, but have had decals installed
or removed across affected lap joints, large cargo door hinges, or external doublers. If those airplanes had
previously been determined to not require inspections in accordance with the original issue of this service bulletin,
do the lap joint, large cargo door hinge, and external doubler inspections in accordance with Paragraph 3.B.,
PART 11 at the applicable time for the affected decal locations.
Federal Aviation Administration (FAA) Notice of Proposed Rule Making FAA NPRM 2009-NM-004-AD is related
to this service bulletin.
No airplanes were added to this service bulletin effectivity.
REASON FOR REVISION
This revision is sent to include information about scribe lines that may exist in the fuselage skin around external
decals that may have been installed or removed. Only the inspection areas described in the original issue of
this service bulletin (external doubler locations, Zone 1, Zone 2, Zone 3, Zone 4, and large cargo door hinge
locations) require inspections for scribe lines, which may include scribe lines associated with the installation or
removal of decals.
References to FAA Notice of Proposed Rule Making FAA NPRM 2009-NM-004-AD were added to this service
bulletin.
The data given in Information Notice 777-53A0054 IN 01 is included in this revision. IN 01 included clarification
of the notes in Paragraph 1.E., Compliance, and corrections for various typographic errors.
Vertical lines are put on the left edge of each page, except in Paragraph 1.A., Effectivity, to show the location
of important changes.
Pages with no vertical lines have no important changes.
REVISION HISTORY
August 07, 2008Original Issue:
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: August 07, 2008
777-53A0054Revision 1: November 04, 2010
5 of 91

### Page 6

November 04, 2010Revision 1:
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: August 07, 2008
777-53A0054Revision 1: November 04, 2010
6 of 91
BOEING SERVICE BULLETIN 777-53A0054

### Page 7

Commercial 
Airplanes
777
Service Bulletin
SummaryNumber: 777-53A0054Original Issue: August 07, 2008
Revision 1: November 04, 2010
ATA System: 5300
SUBJECT: FUSELAGE - Body Station 132.5 to Body Station 2150 - External Inspection of the
Fuselage Skin for External Scribe Lines
CONCURRENT REQUIREMENTS
None.
BACKGROUND
This service bulletin gives instructions for the inspection and repair of scribe lines in the fuselage skin at certain
lap joints, butt joints, and external repair doublers, and around the large cargo door hinges. Fatigue cracks can
develop in the skin at scribe line locations. Fatigue cracks in the skin that remain undetected could grow large
and cause sudden decompression and the inability to sustain limit load.
A scribe line is a narrow, shallow, distinct line of damage (up to 0.006 inch deep), usually associated with the
removal of a fillet or gap seal. A more detailed definition of a scribe line is included in Paragraph 3.B.,
Accomplishment Instructions.
At the time this service bulletin was originally released, only one 777 airplane has been found with scribe damage
by one operator. On this airplane, scribe lines were found around the edges of the area where a large decal had
been installed. The operator believed that the scribe lines were made when the decal was removed. No cracks
were found at the scribe line locations. On other airplane models, scribe lines appear to have been made when
sealant was removed as part of preparation of the airplane for repainting, and have in some cases resulted in
significant cracking.
Subsequent to the original issue of this service bulletin, it was determined that scribe lines could occur when
decals are installed or removed, even on airplanes that had not previously been stripped or repainted.
Accomplishment of the inspections shown in this service bulletin will help make sure that fatigue cracks that can
form in the fuselage skin at scribe lines are found and repaired before they can become large and cause sudden
loss of cabin pressure.
Boeing Service Related Problem (SRP) 777-SRP-53-0243 is related to this service bulletin.
ACTION
The lap joint and butt joint locations that should be inspected are divided into four zones to address the most
critical areas first and to give less critical areas appropriately reduced compliance requirements. In addition to
these four zones, detailed inspections are also required at certain external doubler locations and around the
large cargo door hinges.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: August 07, 2008
777-53A0054Revision 1: November 04, 2010
7 of 91

### Page 8

At the times shown in Paragraph 1.E., Compliance, start to do detailed inspections for scribe lines in the affected
areas. If no scribe lines are found in that area, no more inspections are necessary in that affected area. If scribe
lines are found, do detailed, eddy current or ultrasonic inspections of the scribes lines for cracks. If cracks are
found, repair before further flight. If no cracks are found, repair the scribe lines. As an alternative to scribe line
repair, if the scribe lines are no more than 0.006 inch deep restore the finish in the area and do the inspections
for cracks again at the times shown in this service bulletin.
EFFECTIVITY
777-200, 777-200LR, 777-300, and 777-300ER Airplanes. Refer to Paragraph 1.A.1., Airplanes for the list of
affected airplanes.
COMPLIANCE
Refer to Paragraph 1.E., Compliance.
Federal Aviation Administration (FAA) Notice of Proposed Rule Making FAA NPRM 2009-NM-004-AD, is related
to this service bulletin.2009-NM-004-AD
INDUSTRY SUPPORT INFORMATION
Boeing warranty remedies are not available for the inspections and repair procedures given in this service
bulletin.
MANPOWER
Refer to Paragraph 1.G., Manpower.
MATERIAL INFORMATION
None.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: August 07, 2008
777-53A0054Revision 1: November 04, 2010
8 of 91
BOEING SERVICE BULLETIN 777-53A0054

### Page 9

Commercial 
Airplanes
777
Service Bulletin
Number: 777-53A0054
Original Issue: August 07, 2008
Revision 1: November 04, 2010
ATA System: 5300
SUBJECT: FUSELAGE - Body Station 132.5 to Body Station 2150 - External Inspection of the
Fuselage Skin for External Scribe Lines
1.    PLANNING INFORMATION
A. Effectivity
1. Airplanes
Refer to Service Bulletin Index Document D624W001 Part 3 for Airplane Variable Number, Line
Number, and Serial Number data.
This service bulletin is for the airplanes shown below.
DESCRIPTIONCONFIGURATIONGROUP
777-200 and 777-200LR airplanes through line number 660 with a
small aft cargo door.
-1
777-200 and 777-200LR airplanes through line number 660 with a
large aft cargo door.
-2
777-300 and 777-300ER airplanes through line number 660 with a
small aft cargo door.
-3
777-300 and 777-300ER airplanes through line number 660 with a
large aft cargo door.
-4
Airplane Models:
777-200, 777-200LR, 777-300, 777-300ER
GroupVariable Number
2WA001 - WA017
1WA076 - WA080
1WA086 - WA093
1WA101 - WA104
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: August 07, 2008
777-53A0054Revision 1: November 04, 2010
9 of 91

### Page 10

GroupVariable Number
1WA116 - WA119
1WA131 - WA137
1WA171 - WA175
1WA196 - WA198
1WA206 - WA212
2WA221 - WA223
2WA231 - WA232
1WA241 - WA250
2WA261 - WA266
1WA281 - WA283
1WA301 - WA304
1WB001
2WB002 - WB021
2WB031 - WB046
2WB051 - WB088
1WB101 - WB106
1WB121 - WB125
1WB131 - WB144
1WB151 - WB155
1WB161 - WB177
1WB181 - WB194
1WB201 - WB215
1WB231 - WB247
1WB271 - WB272
2WB273
1WB276 - WB285
2WB286
2WB291 - WB302
2WB306 - WB307
2WB311 - WB337
2WB341 - WB342
2WB366 - WB368
2WB371 - WB388
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: August 07, 2008
777-53A0054Revision 1: November 04, 2010
10 of 91
BOEING SERVICE BULLETIN 777-53A0054

### Page 11

GroupVariable Number
1WB406
2WB411 - WB413
1WB416 - WB439
2WB446 - WB453
1WB476
2WB481 - WB484
4WB501 - WB512
3WB531 - WB537
3WB551 - WB554
3WB591 - WB597
3WB601 - WB606
3WB611 - WB622
4WB631 - WB638
4WB646 - WB649
1WC051 - WC073
2WC101 - WC104
1WC111 - WC119
2WC221 - WC222
2WC241 - WC243
2WC281 - WC290
2WC301 - WC308
2WC361 - WC364
1WC371 - WC374
2WC381 - WC395
1WC441
1WC446 - WC449
2WC456 - WC459
2WC486 - WC493
2WC506 - WC508
2WC521 - WC522
2WC531 - WC534
2WC546 - WC547
2WC556
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: August 07, 2008
777-53A0054Revision 1: November 04, 2010
11 of 91
BOEING SERVICE BULLETIN 777-53A0054

### Page 12

GroupVariable Number
2WC566 - WC567
1WD001 - WD002
1WD011 - WD013
2WD031 - WD032
2WD046
3WD501 - WD506
4WD521 - WD536
4WD546 - WD552
4WD561 - WD570
4WD581 - WD592
4WD606 - WD609
4WD621 - WD632
4WD651 - WD657
4WD671 - WD675
3WD691 - WD700
4WD741 - WD745
4WD761 - WD765
3WD786 - WD787
3WD826 - WD828
2. Spares Affected
None.
B. Concurrent Requirements
None.
C. Reason
This service bulletin gives instructions for the inspection and repair of scribe lines in the fuselage skin
at certain lap joints, butt joints, and external repair doublers, and around the large cargo door hinges.
Fatigue cracks can develop in the skin at scribe lines. Fatigue cracks in the skin can become large and
cause a sudden loss of cabin pressure and the inability to sustain limit load.
At the time this service bulletin was originally released, only one 777 airplane has been found with
scribe damage by one operator. On this airplane, scribe lines were found around the edges of the area
where a large decal had been installed. The operator believed that the scribe lines were made when
the decal was removed. No cracks were found at the scribe line locations. On other airplane models,
scribe lines appear to have been made when sealant was removed as part of preparation of the airplane
for repainting.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: August 07, 2008
777-53A0054Revision 1: November 04, 2010
12 of 91
BOEING SERVICE BULLETIN 777-53A0054

### Page 13

Subsequent to the original issue of this service bulletin, it was determined that scribe lines could occur
when decals are installed or removed, even on airplanes that had not previously been stripped or
repainted.
Accomplishment of the inspections shown in this service bulletin will help make sure that fatigue cracks
that can form in the fuselage skin at scribe lines are found and repaired before they can become large
and cause sudden loss of cabin pressure.
Boeing Service Related Problem (SRP) 777-SRP-53-0243 is related to this service bulletin.
Revision 1 is sent to include information about scribe lines that may exist in the fuselage skin around
external decals that may have been installed or removed. Only the inspection areas described in the
original issue of this service bulletin (external doubler locations, Zone 1, Zone 2, Zone 3, Zone 4, and
large cargo door hinge locations) require inspections for scribe lines, which may include scribe lines
associated with the installation or removal of decals. References to FAA Notice of Proposed Rule
Making FAA NPRM 2009-NM-004-AD were added to this service bulletin. The data given in Information
Notice 777-53A0054 IN 01 is included in this revision. IN 01 included clarification of the notes in
Paragraph 1.E., Compliance, and corrections for various typographic errors.
D. Description
The lap joint and butt joint locations that should be inspected are divided into four zones to address
the most critical areas first and to give less critical areas appropriately reduced compliance requirements.
In addition to these four zones, detailed inspections are also required at certain external doubler
locations and around the large cargo door hinges.
At the times shown in Paragraph 1.E., Compliance, start to do detailed inspections for scribe lines in
the affected areas. If no scribe lines are found in that area, no more inspections are necessary in that
affected area. If scribe lines are found, do detailed, eddy current or ultrasonic inspections of the scribes
lines for cracks. If cracks are found, repair before further flight. No more inspections are required in
the repaired area. If no cracks are found, repair the scribe lines. As an alternative to scribe line repair,
if the scribe lines are no more than 0.006 inch deep restore the finish in the area and do the inspections
for cracks again at the times shown in this service bulletin.
Revision 1 - More work is necessary on airplanes which have not been stripped or repainted, but have
had decals installed or removed across affected lap joints, large cargo door hinges, or external doublers.
If those airplanes had previously been determined to not require inspections in accordance with the
original issue of this service bulletin, do the lap joint, large cargo door hinge, and external doubler
inspections in accordance with Paragraph 3.B., PART 11 at the applicable time for the affected decal
locations.
The work in this service bulletin is done in the maintenance zone(s) given below.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: August 07, 2008
777-53A0054Revision 1: November 04, 2010
13 of 91
BOEING SERVICE BULLETIN 777-53A0054

### Page 14

Group 1-2:
Affected Maintenance Zones
ZoneModel
111, 112, 113, 114, 115, 116, 117, 118, 121,
122, 123, 124, 125, 126, 151, 152, 153, 154,
161, 162, 163, 164, 165, 166, 211, 212, 221,
222, 223, 224, 231, 232, 233, 234, 241, 242,
243, 244, 251, 252, 253, 254, 261, 262, 263, 264
777-200, 777-200LR
Group 3-4:
Affected Maintenance Zones
ZoneModel
111, 112, 113, 114, 115, 116, 117, 118, 121,
122, 123, 124, 125, 126, 151, 152, 153, 154,
161, 162, 163, 164, 165, 166, 211, 212, 221,
222, 223, 224, 231, 232, 233, 234, 241, 242,
243, 244, 251, 252, 253, 254, 261, 262, 263, 264
777-300, 777-300ER
E. Compliance
Federal Aviation Administration (FAA) Notice of Proposed Rule Making FAA NPRM 2009-NM-004-AD,
is related to this service bulletin.2009-NM-004-AD
NOTE: The inspections shown in this service bulletin are not necessary if the operator can
show that the airplane has never been stripped or repainted since delivery from
Boeing and the operator can show the airplane has never had external decals installed
across the pressurized fuselage skin lap joints, cargo door hinges, or external doublers
that are required to be inspected in accordance with this service bulletin. Any area
of the airplane that the operator can show: a) has never been stripped or repainted
since delivery from Boeing, and b) has never had decals applied or removed since
delivery from Boeing, does not need to be inspected per this service bulletin.
1.
2. The inspections shown in this service bulletin are not necessary in any areas where
the operator can show that, since airplane delivery from Boeing: a) removal of sealant
at all times has been done using the proper sealant removal procedures and b) no
decals have been installed or removed from these areas. Refer to Appendix A for
proper sealant removal procedures.
3. The lap joint inspections shown in this service bulletin are not necessary at the S-5,
S-14, S-24, or S-45 lap joints aft of STA 508, where there is no existing fillet seal at
those lap joints, and the operator can show that no fillet seal was previously removed
from those lap joints and that the operator can show that decals have not been cut
across these lap joints. The lap joints must be inspected at locations where decals
may have been cut at the lap joints whether there has ever been a fillet seal at these
locations or not.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: August 07, 2008
777-53A0054Revision 1: November 04, 2010
14 of 91
BOEING SERVICE BULLETIN 777-53A0054

### Page 15

4. The lap joint inspections shown in this service bulletin are not necessary at the S-34
lap joints aft of STA 655 where there is no existing fillet seal at that lap joint, and the
operator can show that no fillet seal was previously removed from that lap joint and
that the operator can show that decals have not been cut across these lap joints.
The lap joints must be inspected at locations where decals may have been cut at
the lap joints whether there has ever been a fillet seal at these locations or not.
5. For each repair, if the operator can show that the airplane has never been stripped
or repainted since the repair has been installed and that a decal has not been cut at
an edge of the repair, then the repair inspections for that specific repair are not
required.
6. Where this service bulletin refers to "paint records", this term includes records of
repainting of the airplane as well as records of decal installations and removals.
Boeing recommends that the inspections in this service bulletin be done in accordance with the tables
that follow:
NOTE: In the tables that follow, "date of delivery from Boeing" is defined as the issue date of the
original airworthiness certificate or export certificate of airworthiness for a specific airplane.
Table 1: Initial Inspection Threshold and Repeat Inspection Intervals for External Repair Doubler Locations
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Last)
ActionCondition
-6,000 flight-cy-
cles after the
original issue
date on this ser-
vice bulletin.
15,000 total
flight-cycles,
plus the total
number of flight-
cycles at 1,500
days after the
date of delivery
from Boeing.
Do detailed inspections
for scribe lines at external
repair doubler locations
in accordance with Para-
graph 3.B., PART 1.
If repair and paint records
are not available:
-6,000 flight-cy-
cles after the
original issue
date on this ser-
vice bulletin.
15,000 total
flight-cycles,
plus the total
number of flight-
cycles at the
time the repair
was installed.
Do detailed inspections
for scribe lines at external
repair doubler locations
in accordance with Para-
graph 3.B., PART 1.
If only the repair record is
available:
-6,000 flight-cy-
cles after the
original issue
date on this ser-
vice bulletin.
15,000 total
flight-cycles,
plus the total
number of flight-
cycles at the
time of the first
repaint since
delivery from
Boeing.
Do detailed inspections
for scribe lines at external
repair doubler locations
in accordance with Para-
graph 3.B., PART 1.
If only the paint record is
available:
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: August 07, 2008
777-53A0054Revision 1: November 04, 2010
15 of 91
BOEING SERVICE BULLETIN 777-53A0054

### Page 16

Table 1: Initial Inspection Threshold and Repeat Inspection Intervals for External Repair Doubler Locations
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Last)
ActionCondition
-6,000 flight-cy-
cles after the
original issue
date on this ser-
vice bulletin.
15,000 total
flight-cycles,
plus the total
number of flight-
cycles at the
time of the first
repaint after in-
stallation of the
repair.
Do detailed inspections
for scribe lines at external
repair doubler locations
in accordance with Para-
graph 3.B., PART 1.
If both the repair and paint
records are available:
--No more work is neces-
sary. Inspect for scribe
lines at other locations in
accordance with Table 2.
No scribe lines found
-Before further flightDo detailed, eddy current
or ultrasonic inspections
of the scribe lines for
cracks in accordance with
Paragraph 3.B., PART 1.
(a)
Scribe lines found
-Before further flightRepair in accordance with
Paragraph 3.B., PART 1.
Cracks found
Start to do detailed in-
spections for scribe lines
at Zone 4 locations at the
times given in Table 5.
Start to do detailed in-
spections for scribe lines
at large cargo door hinge
areas in accordance with
Table 6. (a)
--No more work is neces-
sary at scribe lines veri-
fied to be crack-free and
less than 0.001 inch
deep. Inspect for scribe
lines at other locations in
accordance with Table 2.
No cracks found, and all
scribe lines are less than
0.001 inch deep.
-Before further flight.Repair in accordance with
Paragraph 3.B., PART 1.
(a)
No cracks found, and any
scribe line found is more
than 0.006 inch deep.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: August 07, 2008
777-53A0054Revision 1: November 04, 2010
16 of 91
BOEING SERVICE BULLETIN 777-53A0054

### Page 17

Table 1: Initial Inspection Threshold and Repeat Inspection Intervals for External Repair Doubler Locations
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Last)
ActionCondition
-Within 1,200 flight-cycles of the
initial inspection.
Repair in accordance with
Paragraph 3.B., PART 1.
(a)
No cracks found, and any
scribe lines found are
0.001 inch deep or more,
but less than or equal to
0.006 inch deep.
or
1,200 flight-cyclesWithin 1,200 flight-cycles of the
previous inspection.
Do repeat detailed, eddy
current or ultrasonic in-
spections of the scribe
lines in accordance with
Paragraph 3.B., PART
10. (a)
(a) Inspect for scribe lines at other locations in accordance with Table 2.
Table 2: Zone 1 Initial Inspection Threshold and Repeat Inspection Intervals
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Last)
ActionCondition
-6,000 flight-cy-
cles after the
original issue
date on this ser-
vice bulletin.
32,000 total
flight-cycles,
plus the total
number of flight-
cycles at 1,500
days after the
date of delivery
from Boeing.
Do detailed inspections
for scribe lines at Zone 1
locations in accordance
with Paragraph 3.B.,
PART 2.
If the paint record is not
available:
-6,000 flight-cy-
cles after the
original issue
date on this ser-
vice bulletin.
32,000 total
flight-cycles,
plus the total
number of flight-
cycles at the
time of the first
repaint since
delivery from
Boeing.
Do detailed inspections
for scribe lines at Zone 1
locations in accordance
with Paragraph 3.B.,
PART 2.
If the paint record is avail-
able:
--No more work is neces-
sary. Inspect for scribe
lines at other locations in
accordance with Table 3.
No scribe lines found
-Before further flightDo detailed, eddy current
or ultrasonic inspections
of the scribe lines for
cracks in accordance with
Paragraph 3.B., PART 2.
(a)
Scribe lines found
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: August 07, 2008
777-53A0054Revision 1: November 04, 2010
17 of 91
BOEING SERVICE BULLETIN 777-53A0054

### Page 18

Table 2: Zone 1 Initial Inspection Threshold and Repeat Inspection Intervals
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Last)
ActionCondition
-Before further flightRepair in accordance with
Paragraph 3.B., PART 2.
Cracks found
Start to do inspections for
scribe lines at Zone 4 lo-
cations at the times given
in Table 5. Start to do de-
tailed inspections for
scribe lines at large cargo
door hinge areas in accor-
dance with Table 6. (a)
--No more work is neces-
sary at scribe lines veri-
fied to be crack-free and
less than 0.001 inch
deep. Inspect for scribe
lines at other locations in
accordance with Table 3.
No cracks found, and all
scribe lines are less than
0.001 inch deep.
-Before further flightRepair in accordance with
Paragraph 3.B., PART 2.
(a)
No cracks found, and any
scribe line found is more
than 0.006 inch deep.
-Within 1,800 flight-cycles of the
initial inspection.
Repair in accordance with
Paragraph 3.B., PART 2.
(a)
No cracks found, and any
scribe lines found are
0.001 inch deep or more,
but less than or equal to
0.006 inch deep.
or
1,800 flight-cyclesWithin 1,800 flight-cycles of the
previous inspection.
Do repeat detailed, eddy
current or ultrasonic in-
spections of the scribe
lines in accordance with
Paragraph 3.B., PART
10. (a)
(a) Inspect for scribe lines at other locations in accordance with Table 3.
Table 3: Zone 2 Initial Inspection Threshold and Repeat Inspection Intervals
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Last)
ActionCondition
-6,000 flight-cy-
cles after the
original issue
date on this ser-
vice bulletin.
32,000 total
flight-cycles,
plus the total
number of flight-
cycles at 1,500
days after the
date of delivery
from Boeing.
Do detailed inspections
for scribe lines at Zone 2
locations in accordance
with Paragraph 3.B.,
PART 3.
If the paint record is not
available:
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: August 07, 2008
777-53A0054Revision 1: November 04, 2010
18 of 91
BOEING SERVICE BULLETIN 777-53A0054

### Page 19

Table 3: Zone 2 Initial Inspection Threshold and Repeat Inspection Intervals
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Last)
ActionCondition
-6,000 flight-cy-
cles after the
original issue
date on this ser-
vice bulletin.
32,000 total
flight-cycles,
plus the total
number of flight-
cycles at the
time of the first
repaint since
delivery from
Boeing.
Do detailed inspections
for scribe lines at Zone 2
locations in accordance
with Paragraph 3.B.,
PART 3.
If the paint record is avail-
able:
--No more work is neces-
sary. Inspect for scribe
lines at other locations in
accordance with Table 4.
No scribe lines found
-Before further flightDo detailed, eddy current
or ultrasonic inspections
of the scribe lines for
cracks in accordance with
Paragraph 3.B., PART 3.
(a)
Scribe lines found
-Before further flightRepair in accordance with
Paragraph 3.B., PART 3.
Cracks found
Start to do inspections for
scribe lines at Zone 4 lo-
cations at the times given
in Table 5. Start to do de-
tailed inspections for
scribe lines at large cargo
door hinge areas in accor-
dance with Table 6. (a)
--No more work is neces-
sary at scribe lines veri-
fied to be crack-free and
less than 0.001 inch
deep. Inspect for scribe
lines at other locations in
accordance with Table 4.
No cracks found, and all
scribe lines are less than
0.001 inch deep.
-Before further flightRepair in accordance with
Paragraph 3.B., PART 3.
(a)
No cracks found, and any
scribe line found is more
than 0.006 inch deep.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: August 07, 2008
777-53A0054Revision 1: November 04, 2010
19 of 91
BOEING SERVICE BULLETIN 777-53A0054

### Page 20

Table 3: Zone 2 Initial Inspection Threshold and Repeat Inspection Intervals
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Last)
ActionCondition
-Within 2,500 flight-cycles of the
initial inspection.
Repair in accordance with
Paragraph 3.B., PART 3.
(a)
No cracks found, and any
scribe lines found are
0.001 inch deep or more,
but less than or equal to
0.006 inch deep.
or
2,500 flight-cyclesWithin 2,500 flight-cycles of the
previous inspection.
Do detailed, eddy current
or ultrasonic repeat in-
spections of the scribe
lines in accordance with
Paragraph 3.B., PART
10. (a)
(a) Inspect for scribe lines at other locations in accordance with Table 4.
Table 4: Zone 3 Initial Inspection Threshold and Repeat Inspection Intervals
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Last)
ActionCondition
-6,000 flight-cy-
cles after the
original issue
date on this ser-
vice bulletin.
32,000 total
flight-cycles,
plus the total
number of flight-
cycles at 1,500
days after the
date of delivery
from Boeing.
Do detailed inspections
for scribe lines at Zone 3
locations in accordance
with Paragraph 3.B.,
PART 4.
If the paint record is not
available:
-6,000 flight-cy-
cles after the
original issue
date on this ser-
vice bulletin.
32,000 total
flight-cycles,
plus the total
number of flight-
cycles at the
time of the first
repaint since
delivery from
Boeing.
Do detailed inspections
for scribe lines at Zone 3
locations in accordance
with Paragraph 3.B.,
PART 4.
If the paint record is avail-
able:
--No more work is neces-
sary.
No scribe lines found
-Before further flightDo detailed, eddy current
or ultrasonic inspections
of the scribe lines for
cracks in accordance with
Paragraph 3.B., PART 4.
Scribe lines found
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: August 07, 2008
777-53A0054Revision 1: November 04, 2010
20 of 91
BOEING SERVICE BULLETIN 777-53A0054

### Page 21

Table 4: Zone 3 Initial Inspection Threshold and Repeat Inspection Intervals
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Last)
ActionCondition
-Before further flightRepair in accordance with
Paragraph 3.B., PART 4.
Cracks found
Start to do inspections for
scribe lines at Zone 4 lo-
cations at the times given
in Table 5. Start to do de-
tailed inspections for
scribe lines at large cargo
door hinge areas in accor-
dance with Table 6.
--No more work is neces-
sary at scribe lines veri-
fied to be crack-free and
less than 0.001 inch
deep.
No cracks found, and all
scribe lines are less than
0.001 inch deep.
-Before further flightRepair in accordance with
Paragraph 3.B., PART 4.
No cracks found, and any
scribe line found is more
than 0.006 inch deep.
-Within 3,500 flight-cycles of the
initial inspection.
Repair in accordance with
Paragraph 3.B., PART 4.
No cracks found, and any
scribe lines found are
0.001 inch deep or more,
but less than or equal to
0.006 inch deep.
or
3,500 flight-cyclesWithin 3,500 flight-cycles of the
previous inspection.
Do repeat detailed, eddy
current or ultrasonic in-
spections of the scribe
lines in accordance with
Paragraph 3.B., PART
10.
NOTE: The inspections shown in Table 5 for Zone 4 are only necessary if cracks were found at scribe
lines around external repair doublers or in Zone 1, Zone 2, or Zone 3.
Table 5: Zone 4 Initial Inspection Threshold and Repeat Inspection Intervals
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Last)
ActionCondition
-6,000 flight-cy-
cles after the
original issue
date on this ser-
vice bulletin.
45,000 total
flight-cycles,
plus the total
number of flight-
cycles at 1,500
days after the
date of delivery
from Boeing.
Do detailed inspections
for scribe lines at Zone 4
locations in accordance
with Paragraph 3.B.,
PART 5.
If the paint record is not
available:
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: August 07, 2008
777-53A0054Revision 1: November 04, 2010
21 of 91
BOEING SERVICE BULLETIN 777-53A0054

### Page 22

Table 5: Zone 4 Initial Inspection Threshold and Repeat Inspection Intervals
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Last)
ActionCondition
-6,000 flight-cy-
cles after the
original issue
date on this ser-
vice bulletin.
45,000 total
flight-cycles,
plus the total
number of flight-
cycles at the
time of the first
repaint since
delivery from
Boeing.
Do detailed inspections
for scribe lines at Zone 4
locations in accordance
with Paragraph 3.B.,
PART 5.
If the paint record is avail-
able:
--No more work is neces-
sary. (a)
No scribe lines found
-Before further flightDo detailed, eddy current
or ultrasonic inspections
of the scribe lines for
cracks in accordance with
Paragraph 3.B., PART 5.
(a)
Scribe lines found
-Before further flightRepair in accordance with
Paragraph 3.B., PART 5.
(a)
Cracks found
--No more work is neces-
sary at scribe lines veri-
fied to be crack-free and
less than 0.001 inch
deep. (a)
No cracks found, and all
scribe lines are less than
0.001 inch deep.
-Before further flightRepair in accordance with
Paragraph 3.B., PART 5.
(a)
No cracks found, and any
scribe line found is more
than 0.006 inch deep.
-Within 5,000 flight-cycles of the
initial inspection.
Repair in accordance with
Paragraph 3.B., PART 5.
(a)
No cracks found, and any
scribe lines found are
0.001 inch deep or more,
but less than or equal to
0.006 inch deep.
or
5,000 flight-cyclesWithin 5,000 flight-cycles of the
previous inspection.
Do repeat detailed, eddy
current or ultrasonic in-
spections of the scribe
lines in accordance with
Paragraph 3.B., PART
10. (a)
(a) Inspect for scribe lines at other locations in accordance with Table 6.
NOTE: The inspections shown in Table 6 for the large cargo door hinge areas are only necessary if
cracks were found at scribe lines around external repair doublers or in Zone 1, Zone 2, or
Zone 3.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: August 07, 2008
777-53A0054Revision 1: November 04, 2010
22 of 91
BOEING SERVICE BULLETIN 777-53A0054

### Page 23

Table 6: Large Cargo Door Hinge Inspection Threshold and Repeat Inspection Intervals
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Last)
ActionCondition
-6,000 flight-cy-
cles after the
original issue
date on this ser-
vice bulletin.
45,000 total
flight-cycles,
plus the total
number of flight-
cycles at 1,500
days after the
date of delivery
from Boeing.
Do detailed inspections
for scribe lines at the
large cargo door hinges
in accordance with Para-
graph 3.B., PART 6.
If the paint record is not
available:
-6,000 flight-cy-
cles after the
original issue
date on this ser-
vice bulletin.
45,000 total
flight-cycles,
plus the total
number of flight-
cycles at the
time of the first
repaint since
delivery from
Boeing.
Do detailed inspections
for scribe lines at large
cargo door hinges in ac-
cordance with Paragraph
3.B., PART 6.
If the paint record is avail-
able:
--No more work is neces-
sary.
No scribe lines found
-Before further flightDo detailed, eddy current
or ultrasonic inspections
of the scribe lines for
cracks in accordance with
Paragraph 3.B., PART 6.
Scribe lines found
-Before further flightRepair in accordance with
Paragraph 3.B., PART 6.
Cracks found
--No more work is neces-
sary at scribe lines veri-
fied to be crack-free and
less than 0.001 inch
deep.
No cracks found, and all
scribe lines are less than
0.001 inch deep.
-Before further flightRepair in accordance with
Paragraph 3.B., PART 6.
No cracks found, and any
scribe line found is more
than 0.006 inch deep.
-Within 5,000 flight-cycles of the
initial inspection.
Repair in accordance with
Paragraph 3.B., PART 6.
No cracks found, and any
scribe lines found are
0.001 inch deep or more,
but less than or equal to
0.006 inch deep.
or
5,000 flight-cyclesWithin 5,000 flight-cycles of the
previous inspection.
Do repeat detailed, eddy
current or ultrasonic in-
spections of the scribe
lines in accordance with
Paragraph 3.B., PART
10.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: August 07, 2008
777-53A0054Revision 1: November 04, 2010
23 of 91
BOEING SERVICE BULLETIN 777-53A0054

### Page 24

Contact Boeing for inspection requirements for operation beyond 60,000 total flight-cycles after first
repaint.
F. Approval
This service bulletin was examined by the Federal Aviation Administration (FAA). The changes specified
in this service bulletin comply with the applicable regulations and are FAA approved, as well as European
Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved
airplanes listed in the service bulletin effectivity. This service bulletin and its approval were based on
the airplane in its original Boeing delivery configuration or as modified by other approved Boeing
changes.
If an airplane has a non-Boeing modification or repair that affects a component or system also affected
by this service bulletin, the operator is responsible for obtaining appropriate regulatory agency approval
before incorporating this service bulletin.
The Manager of the Seattle Aircraft Certification Office (SACO) approves the accomplishment of the
inspections and repair procedures defined in Service Bulletin 777-53A0054, Revision 1 as an alternative
method of compliance (AMOC) to the inspections and repair procedures defined in SB 777-53A0054,
dated August 7, 2008, required by paragraph (g) of AD 2009-24-08. All provisions of AD 2009-24-08
that are not specifically referenced in the preceding sentence remain fully applicable and must be
complied with.
G. Manpower
The table below shows an estimate of the task hours necessary to do this inspection for each airplane.
This estimate is for direct labor only, done by an experienced crew. Adjust the estimate with operator
task hour data if necessary. The estimate does not include lost time. These are some examples of lost
time:
 Time to adjust to the workplace
 Time to schedule the work
 Time to inspect the work
 Time to cure the materials
 Time to make the parts
 Time to find the tools.
Group 1:
Elapsed HoursTask HoursNumber of Per-
sons
Task
32.51956Prepare Zone 2 for inspection
3.572Inspect Zone 2 for scribe lines
17513Restore Zone 2
53253TOTAL FOR ZONE 2
584648Prepare Zone 3 for inspection
4164Inspect Zone 3 for scribe lines
30.51224Restore Zone 3
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: August 07, 2008
777-53A0054Revision 1: November 04, 2010
24 of 91
BOEING SERVICE BULLETIN 777-53A0054

### Page 25

Group 1:
Elapsed HoursTask HoursNumber of Per-
sons
Task
92.5602TOTAL FOR ZONE 3
15.5936Prepare Zone 4 for inspection
1.753.52Inspect Zone 4 for scribe lines
6244Restore Zone 4
23.25120.5TOTAL FOR ZONE 4
5102Prepare forward cargo door hinges
for inspection
0.50.51Inspect forward large cargo door
hinges for scribe lines
1.252.52Restore forward large cargo door
hinges
6.7513TOTAL FOR CARGO DOOR HINGES
175.5988.5TOTAL FOR EACH AIRPLANE
Group 2:
Elapsed HoursTask HoursNumber of Per-
sons
Task
32.51956Prepare Zone 2 for inspection
3.572Inspect Zone 2 for scribe lines
17513Restore Zone 2
53253TOTAL FOR ZONE 2
57.754628Prepare Zone 3 for inspection
4164Inspect Zone 3 for scribe lines
30.51224Restore Zone 3
92.25600TOTAL FOR ZONE 3
15.5936Prepare Zone 4 for inspection
1.753.52Inspect Zone 4 for scribe lines
6244Restore Zone 4
23.25120.5TOTAL FOR ZONE 4
5204Prepare forward and aft cargo door
hinges for inspection
0.512Inspect forward and aft large cargo
door hinges for scribe lines
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: August 07, 2008
777-53A0054Revision 1: November 04, 2010
25 of 91
BOEING SERVICE BULLETIN 777-53A0054

### Page 26

Group 2:
Elapsed HoursTask HoursNumber of Per-
sons
Task
2.755.52Restore forward and aft large cargo
door hinges
8.2526.5TOTAL FOR CARGO DOOR HINGES
176.751000TOTAL FOR EACH AIRPLANE
Group 3:
Elapsed HoursTask HoursNumber of Per-
sons
Task
7284Prepare Zone 1 for inspection
0.512Inspect Zone 1 for scribe lines
3.757.52Restore Zone1
11.2536.5TOTAL FOR ZONE 1
302408Prepare Zone 2 for inspection
4.258.52Inspect Zone 2 for scribe lines
21633Restore Zone 2
55.25311.5TOTAL FOR ZONE 2
473768Prepare Zone 3 for inspection
3124Inspect Zone 3 for scribe lines
21.75874Restore Zone 3
71.75475TOTAL FOR ZONE 3
38.253068Prepare Zone 4 for inspection
5.5112Inspect Zone 4 for scribe lines
20.25814Restore Zone 4
64398TOTAL FOR ZONE 4
5102Prepare forward cargo door hinges
for inspection
0.50.51Inspect forward large cargo door
hinges for scribe lines
1.252.52Restore forward large cargo door
hinges
6.7513TOTAL FOR CARGO DOOR HINGES
2091234TOTAL FOR EACH AIRPLANE
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: August 07, 2008
777-53A0054Revision 1: November 04, 2010
26 of 91
BOEING SERVICE BULLETIN 777-53A0054

### Page 27

Group 4:
Elapsed HoursTask HoursNumber of Per-
sons
Task
7284Prepare Zone 1 for inspection
0.512Inspect Zone 1 for scribe lines
3.757.52Restore Zone1
11.2536.5TOTAL FOR ZONE 1
302408Prepare Zone 2 for inspection
4.258.52Inspect Zone 2 for scribe lines
21633Restore Zone 2
55.25311.5TOTAL FOR ZONE 2
413288Prepare Zone 3 for inspection
3124Inspect Zone 3 for scribe lines
21.75874Restore Zone 3
65.75427TOTAL FOR ZONE 3
38.253068Prepare Zone 4 for inspection
5.5112Inspect Zone 4 for scribe lines
20.25814Restore Zone 4
64398TOTAL FOR ZONE 4
5204Prepare forward and aft cargo door
hinges for inspection
0.512Inspect forward and aft large cargo
door hinges for scribe lines
2.755.52Restore forward and aft large cargo
door hinges
8.2526.5TOTAL FOR CARGO DOOR HINGES
204.51199.5TOTAL FOR EACH AIRPLANE
NOTE: 1. A task-hour estimate for external doubler areas is not given, since the inspections
required can be different depending on the in-service repair history of the airplane.
2. In the tables above, the "prepare" task includes removal of sealant and paint as
necessary for the scribe inspection.
3. More time will be necessary to do additional inspections and possible repairs if scribe
lines are found.
H. Weight and Balance Changes
None.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: August 07, 2008
777-53A0054Revision 1: November 04, 2010
27 of 91
BOEING SERVICE BULLETIN 777-53A0054

### Page 28

I. Electrical Load Data
Not changed.
J. References
1. Existing Data
a. Service Related Problem (SRP) 777-SRP-53-0243
b. 777 Aircraft Maintenance Manual (AMM) 51-21-01, 51-21-02, 51-21-10, 51-31-01
c. 777 Structural Repair Manual (SRM) Chapter 51 and 53
d. 777 Non-Destructive Testing (NDT) Manual Part 10, 53-30-01, Part 4, 53-00-01, Part 4,
53-00-02, Part 6, 51-00-01, Part 6, 53-00-04, Part 6, 53-00-05, Part 6, 53-00-07
e. Standard Overhaul Practices Manual (SOPM) 20-30-03, 20-60-01
f. Federal Aviation Administration (FAA) Notice of Proposed Rule Making 2009-NM-004-AD
2. Data supplied with this Service Bulletin
None.
3. Installation Drawings Used in the Preparation of this Service Bulletin
None.
K. Publications Affected
1. Publications:
None.
2. Damage Tolerance Based Structural Inspections:
Boeing has evaluated the repairs and/or changes in this service bulletin for effects on Fatigue
Critical Structure (FCS) and for changes to Damage Tolerance Inspections (DTI) required in the
Maintenance Program. This service bulletin affects FCS but no new DTIs are necessary.
L. Interchangeability and Intermixability of Parts
Accomplishment of this service bulletin does not affect interchangeability or intermixability of parts.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: August 07, 2008
777-53A0054Revision 1: November 04, 2010
28 of 91
BOEING SERVICE BULLETIN 777-53A0054

### Page 29

2.    MATERIAL INFORMATION
A. Material - Price and Availability
None.
B. Industry Support Information
Boeing warranty remedies are not available for the inspections and repair procedures given in this
service bulletin.
C. Parts Necessary For Each Airplane
1. Kits/Parts
None.
2. Parts and Materials Supplied by the Operator
None.
3. Parts Modified and Reidentified
None.
4. Parts Removed and Not Replaced
None.
D. Parts Necessary to Change Spares
None.
E. Special Tooling - Price and Availability
The operator can supply the tools shown in Paragraph 2.F., Special Tooling Necessary to do this
Service Bulletin. Tool price and supply data are not given.
F. Special Tooling Necessary to do this Service Bulletin
To get the tools shown below, refer to Paragraph 2.E., Special Tooling - Price and Availability.
Maintenance and overhaul tools in the manuals shown in Paragraph 1.J., References, can also be
necessary. Examine operator tool supply to make sure all necessary tools are available.
NameNumber
Digital Optical Micrometer (a) (b)Model Number 8400K
Optical Micrometer (a) (c)Model 966 (Part Number 125632-1) or
Model 966A (part Number 125632)
Laser Measurement System (d)Inspect Cam Model SDMS
(a) These are typical optical micrometers.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: August 07, 2008
777-53A0054Revision 1: November 04, 2010
29 of 91
BOEING SERVICE BULLETIN 777-53A0054

### Page 30

NameNumber
(b) Rene Company 1005 S. Mountain Ave. Monrovia, CA 91016 USA Toll free:
866.358.9955 Tel: 626.358.9955 Fax: 626.358.1448 email: info@renecompany.com
(c) Taber Industries 455 Bryant Street North Towawanda, New York 14120 USA Toll
free: 800.333.5300 (in USA or Canada) Phone: 716.694.4000 Fax: 716.694.1450
(d) Remote Vision Solutions PTY LTD Unit 1 118 Church Street Hawthorn, 3122, Victoria
Australia Phone: +61 3 9815 0933 Fax: +61 3 9818 5597 US Representative: David
Hexter Dallas, Texas Cell Phone: 817.504.8320 dhexter@remotevs.com
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: August 07, 2008
777-53A0054Revision 1: November 04, 2010
30 of 91
BOEING SERVICE BULLETIN 777-53A0054

### Page 31

3.    ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL INFORMATION
CAUTION: KEEP THE WORK AREA, WIRES AND ELECTRICAL BUNDLES CLEAN OF METAL
PARTICLES OR CONTAMINATION WHEN YOU USE TOOLS. UNWANTED MATERIAL,
METAL PARTICLES OR CONTAMINATION CAUGHT IN WIRE BUNDLES CAN CAUSE
DAMAGE TO THE BUNDLES. DAMAGED WIRE BUNDLES CAN CAUSE SPARKS OR
OTHER ELECTRICAL DAMAGE.
NOTE: 1. The instructions identified in Paragraph 3.B., Work Instructions and the Figure(s)
give the recommended sequence of steps. The sequence of steps to do this service
bulletin can be changed.
2. Manual titles are referred to by acronyms. Refer to Paragraph 1.J., References, for
definition of the acronyms.
3. Obey all of the warnings and cautions given in the specified manual sections.
4. Unless shown differently, these dimensions and tolerances are used:
– Linear dimensions are in inches
– Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus
or minus 0.03 inch
– Angular tolerance is plus or minus 2 degrees
5. In the figures, lap joints and butt joint areas that should be inspected are indicated
with heavy lines.
6. If a repair doubler does not span the potential scribe location by 3 or more fastener
rows, but there is no evidence of scribes within 10 inches of the repair, then
inspections under the repair are not required. If scribes exist within 10 inches of the
repair, and the repair does not span the potential scribe by 3 or more rows of
fasteners, then remove the repair and inspect for scribes, or contact Boeing with
details for further evaluation. Inspections are not required in areas where an existing
repair covers a potential scribe line, or the scribe line is within 10 inches of the repair,
provided the repair spans a minimum of three rows beyond each side of the potential
scribe line location (perpendicular to the scribe line direction).
7. A scribe line is defined as a narrow, shallow, distinct line of damage (up to 0.006
inch deep), usually associated with the removal of a fillet or gap seal (lap joints and
butt splices, respectively). Scribe lines can be both tactile (your fingernail will catch
on the scribe); and non-tactile (your fingernail will not catch on the scribe).
Discoloration of the aluminum clad layer or small surface imperfections do not qualify
as a scribe. A lightning strike at a lap joint or butt splice does not qualify as a scribe.
In certain cases the scribe lines have also been associated with the trimming of
fuselage skin decals. Scribe lines that create a potential safety concern are generally
long continuous scribes or several adjacent scribes in a critical orientation at specific
locations with relatively high stresses. Figures are included in this Service Bulletin
to depict typical scribe damage found common to lap joints, butt joints, external
repairs,and large cargo door hinge areas.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: August 07, 2008
777-53A0054Revision 1: November 04, 2010
31 of 91
BOEING SERVICE BULLETIN 777-53A0054

### Page 32

In areas near the lap joints, these scribe lines normally run parallel to the lap joint in
the lower skin along the edge of the upper skin. These scribe lines are typically within
0.25 inch of the lower edge of the upper skin. In some cases, portions of the lines
may be directly adjacent to or slightly under the lower edge of the upper skin, resulting
in hidden scribe lines that cannot be directly viewed without further disassembly. The
ends of these scribe lines may also turn slightly away from the lap joint. Scribe lines
at the butt joints are normally found on the splice plate in the gap between the forward
and aft skin edges and run along the butt joint. Along the edges of external repair
doublers and the large cargo door hinges, scribe lines normally follow the periphery
of the doubler or hinge.
Note that the above is not to be used for the definition of a scribe. Refer to PART 9
for the definition of a scribe.
Appendix B includes information for the fabrication or purchase of a scribe sample
for use as a training aid. The use of this sample is not required when performing
actions of this service bulletin. This sample is an aid in identifying what a scribe may
look and feel like but is not intended to show all damage that is considered a scribe.
When identifying scribes see the definition of a scribe in Part 9 of the accomplishment
instructions.
8. If an optical micrometer or laser measurement system cannot be used because the
upper skin of the lap joint covers a scribe line, then the scribe line depth does not
need to be determined at that location. These scribe lines must be considered typical
and therefore all inspection and other requirements for a typical scribe line apply.
9. It is required that individuals performing ultrasonic inspections on airplanes with
scribe lines to detect cracks per the relevant procedures must be recognized by the
operator or repair station as qualified to perform ultrasonic inspections on their
airplanes AND meet at least one of the following criteria:
— The individual must be qualified to at least Level II in the ultrasonic method in
accordance with an accepted industry standard, i.e. ATA Specification 105,
Mil-Std-410, NAS-410, SNT-TC-1A, or EN-4179 or equivalent. or
— The individual has received specific Boeing training with Boeing providing a
certificate stating that the individual has satisfactorily completed the training in
the specific techniques. or
— The individual has a level I in the ultrasonic method in accordance with an
accepted industry standard and has received specific training and a statement
from the qualifying entity (employer) that the individual is qualified for this
particular inspection.
10. If scribe lines are found during any of the inspections contained in this service bulletin,
when determining the requirements for inspection and repair, each scribe shall be
considered individually.
11. A Detailed Inspection is defined as: An intensive examination of a specific item,
installation, or assembly to detect damage, failure, or irregularity. Available lighting
is normally supplemented with a direct source of good lighting at an intensity deemed
appropriate. Inspection aids such as mirrors, magnifying lenses, etc. may be
necessary. Surface cleaning and elaborate procedures may be required.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: August 07, 2008
777-53A0054Revision 1: November 04, 2010
32 of 91
BOEING SERVICE BULLETIN 777-53A0054

### Page 33

12. These work instructions refer to procedures included in other Boeing documents.
When the words "refer to" are used and the operator has an accepted alternative
procedure, the accepted alternative procedure can be used. When the words "in
accordance with" are included in the instruction, the procedure in the Boeing document
must be used.
13. Refer to Appendix A for sealant removal instructions.
14. Where repair requires disassembly of a lap joint or a butt joint, contact Boeing for
jacking instructions.
15. Where this service bulletin instructs to remove paint, refer to 777 AMM 51-21-01 as
an accepted procedure.
16. Remove sealant using the procedures given in Appendix A of this service bulletin.
17. Where this service bulletin instructs to apply finish, refer to 777 AMM 51-21-02 as
an accepted procedure for preparing an area for paint. Refer to 777 AMM 51-21-10
as an accepted procedure for applying finish.
18. Where this service bulletin instructs to apply sealant, refer to 777 AMM 51-31-01 as
an accepted procedure.
19. Areas under the wing to body fairings are not included in the inspection requirements
of this service bulletin.
B. WORK INSTRUCTIONS
PART 1 - INSPECTION FOR SCRIBES AT EXTERNAL REPAIR DOUBLER LOCATIONS
1. Group 1:
External doubler inspection areas (Area A and Area B) are shown in Figure 1.
2. Group 2:
External doubler inspection areas (Area A and Area B) are shown in Figure 2.
3. Group 3:
External doubler inspection areas (Area A and Area B) are shown in Figure 3.
4. Group 4:
External doubler inspection areas (Area A and Area B) are shown in Figure 4.
5. At or before the initial compliance threshold given in Paragraph 1.E., Compliance, remove the
paint and sealant from the area of the skin around the entire periphery of any external repair
doubler:
a. in Area A that is longer than 6 inches in the longitudinal (forward-aft) direction or longer than
8 inches in the circumferential direction.
b. in Area B that is longer than 6 inches in the longitudinal (forward-aft) direction.
The area of bare skin should be at least one inch wide. Use the sealant removal instructions in
Appendix A of this service bulletin.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: August 07, 2008
777-53A0054Revision 1: November 04, 2010
33 of 91
BOEING SERVICE BULLETIN 777-53A0054

### Page 34

6. Do a detailed inspection of the fuselage skin for scribe lines in the area of bare skin around the
doubler in accordance with Figure 14. The use of at least 10X magnifying lens is required for this
inspection.
7. If no scribe lines are found, apply finish to the skin to match adjacent structure. Apply a fillet seal
of BMS 5-95 or BMS 5-142 sealant at the leading edge of the doubler.
NOTE: It is also acceptable to apply a fillet seal of BMS 5-95 or BMS 5-142 sealant all around
the edges of the doubler.
8. If scribe lines are found, do the steps that follow:
a. Do a detailed inspection of the fuselage skin for scribe lines in these areas of bare skin in
accordance with Figure 14. The use of at least 10X magnifying lens is required for this
inspection.
b. Go to PART 9 and determine if the scribe damage is within the parameters of a "typical" scribe.
If the scribe damage is not within the parameters of a "typical" scribe, repair before further
flight. Repair in accordance with the Structural Repair Manual, replace the damaged skin
panel, or ask Boeing for repair data.
c. Do detailed, eddy current and ultrasonic inspections of all scribe lines that are within the
parameters of a "typical" scribe for cracks in accordance with Figure 19.
d. If any crack indications are found, do the steps that follow:
(1) Send a report about the crack indication to Boeing.
(2) Repair before further flight. Remove the repair doubler to determine the full extent of the
scribe lines and cracks. Do surface HFEC inspections of the skin at any scribe lines found
after doubler removal for cracks. Repair all scribe lines and cracks in accordance with
the Structural Repair Manual, replace the damaged skin panel, or ask Boeing for repair
data.
e. If no crack indications are found, do the following:
(1) No more action is required by this service bulletin at any scribe lines that are determined
to be less than 0.001 inch deep. To determine if scribe lines are less than 0.001 inch
deep, they must be measured using the laser measurement procedure given in 777 NDT
Part 10, 53-30-01.
(2) Repair all scribe lines at external repair doubler locations that are more than 0.006 inch
deep before further flight. Remove the repair doubler to determine the full extent of the
scribe lines and cracks. Do surface HFEC inspections of any scribe lines found after
doubler removal for cracks. Repair all scribe lines and cracks in accordance with the
Structural Repair Manual, replace the damaged skin panel, or ask Boeing for repair data.
(3) If all scribe lines at external doubler locations are 0.006 inch deep or less, apply finish to
the skin to match adjacent structure. Apply a fillet seal of BMS 5-95 or BMS 5-142 sealant
at the leading edge of the doubler. Document the location of all scribe damage that was
found at external doubler locations that was not repaired.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: August 07, 2008
777-53A0054Revision 1: November 04, 2010
34 of 91
BOEING SERVICE BULLETIN 777-53A0054

### Page 35

At or prior to the time given in Paragraph 1.E., Compliance, go to PART 10 and complete
all of the requirements of the Limited Return to Service (LRTS) plan for the scribed areas.
As an alternative, remove the repair doubler to determine the full extent of the scribe lines
and cracks. Do surface HFEC inspections of any scribe lines found after doubler removal
for cracks. Repair all scribe lines and cracks in accordance with the Structural Repair
Manual, replace the damaged skin panel, or ask Boeing for repair data.
NOTE: If all of the scribe lines around an external doubler are less than 0.001 inch deep,
it is acceptable to apply a fillet seal of BMS 5-95 or BMS 5-142 sealant all around
the edges of the doubler.
9. Put the airplane back in a serviceable condition, and do the inspections in PART 2 (Zone 1), PART
3 (Zone 2), PART 4 (Zone 3), PART 5 (Zone 4) and PART 6 (Large Cargo Door Hinges) at the
times specified in Paragraph 1.E., Compliance.
Group 3-4:
PART 2 - ZONE 1 INSPECTION
1. Affected Zone 1 locations are given in Figure 5.
2. At or before the initial compliance threshold given in Paragraph 1.E., Compliance, do detailed
inspections for scribe lines at the affected lap joints in Zone 1 in accordance with PART 7.
3. If no scribe lines are found in Zone 1, no more inspections are necessary in Zone 1. In the areas
that were inspected, apply finish to the skin to match adjacent structure.
NOTE: To reduce the possibility of future scribing, Boeing recommends that no fillet seal be
applied at the lap joints.
4. If scribe lines are found in Zone 1, do the steps that follow:
a. Go to PART 9 and determine if the scribe damage is within the parameters of a "typical" scribe.
If the scribe damage is not within the parameters of a "typical" scribe, repair before further
flight. Repair in accordance with the Structural Repair Manual, replace the damaged skin
panel, or ask Boeing for repair data.
b. Do detailed, eddy current and ultrasonic inspections of all scribe lines that are within the
parameters of a "typical" scribe for cracks in accordance with Figure 19.
c. If any crack indications are found, do the steps that follow:
(1) Send a report about the crack indication to Boeing.
(2) Repair before further flight. Disassemble the full length of the lap joint from the forward
end of the skin panel to the aft end and determine the full extent of the any scribe lines
and cracks. Do surface HFEC inspections of the skin at any scribe lines found during
disassembly for cracks. Repair all scribe lines and cracks found in accordance with the
Structural Repair Manual, replace the damaged skin panel, or ask Boeing for repair data.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: August 07, 2008
777-53A0054Revision 1: November 04, 2010
35 of 91
BOEING SERVICE BULLETIN 777-53A0054

### Page 36

An alternative repair is to repair using an approved method which repairs the entire
complete length of the lap joint, from the forward end of the scribed skin panel to the aft
end.
d. If no crack indications are found, do the following:
(1) No more action is required by this service bulletin at any scribe lines that are determined
to be less than 0.001 inch deep. To determine if scribe lines are less than 0.001 inch
deep, they must be measured using the laser measurement procedure given in 777 NDT
Part 10, 53-30-01.
(2) Repair all scribe lines at Zone 1 lap joint locations that are more than 0.006 inch deep
before further flight. Disassemble the full length of the lap joint from the forward end of
the skin panel to the aft end and determine the full extent of the any scribe lines and
cracks. Do surface HFEC inspections of the skin at any scribe lines found during
disassembly for cracks. Repair all scribe lines and cracks found in accordance with the
Structural Repair Manual, replace the damaged skin panel, or ask Boeing for repair data.
(3) If all scribe lines at Zone 1 lap joint locations are 0.006 inch deep or less, apply finish to
the skin to match adjacent structure. Document the location of all scribe damage that
was found at Zone 1 locations that was not repaired.
At or prior to the time given in Paragraph 1.E., Compliance, go to PART 10 and complete
all of the requirements of the Limited Return to Service (LRTS) plan for the scribed areas.
As an alternative, disassemble the full length of the lap joint from the forward end of the
skin panel to the aft end and determine the full extent of any scribe lines and cracks. Do
surface HFEC inspections of the skin at any scribe lines found during disassembly for
cracks. Repair all scribe lines and cracks found in accordance with the Structural Repair
Manual, replace the damaged skin panel, or ask Boeing for repair data.
5. Put the airplane back in a serviceable condition, and do the inspections in PART 3 (Zone 2), PART
4 (Zone 3), PART 5 (Zone 4) and PART 6 (Large Cargo Door Hinges) at the times specified in
Paragraph 1.E., Compliance.
PART 3 - ZONE 2 INSPECTION
1. Group 1-2:
Affected Zone 2 locations are given in Figure 6.
2. Group 3-4:
Affected Zone 2 locations are given in Figure 7.
3. At or before the initial compliance threshold given in Paragraph 1.E., Compliance, do detailed
inspections for scribe lines at the affected lap joints in Zone 2 in accordance with PART 7.
4. If no scribe lines are found in Zone 2, no more inspections are necessary in Zone 2. In the areas
that were inspected, apply finish to the skin to match adjacent structure.
NOTE: To reduce the possibility of future scribing, Boeing recommends that no fillet seal be
applied at the lap joints.
5. If scribe lines are found in Zone 2, do the steps that follow
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: August 07, 2008
777-53A0054Revision 1: November 04, 2010
36 of 91
BOEING SERVICE BULLETIN 777-53A0054

### Page 37

a. Go to PART 9 and determine if the scribe damage is within the parameters of a "typical" scribe.
If the scribe damage is not within the parameters of a "typical" scribe, repair before further
flight. Repair in accordance with the Structural Repair Manual, replace the damaged skin
panel, or ask Boeing for repair data.
b. Do detailed, eddy current and ultrasonic inspections of all scribe lines that are within the
parameters of a "typical" scribe for cracks in accordance with Figure 19.
c. If any crack indications are found, do the steps that follow:
(1) Send a report about the crack indication to Boeing.
(2) Repair before further flight. Disassemble the full length of the lap joint from the forward
end of the skin panel to the aft end and determine the full extent of the any scribe lines
and cracks. Do surface HFEC inspections of the skin at any scribe lines found during
disassembly for cracks. Repair all scribe lines and cracks found in accordance with the
Structural Repair Manual, replace the damaged skin panel, or ask Boeing for repair data.
An alternative repair is to repair using an approved method which repairs the entire
complete length of the lap joint, from the forward end of the scribed skin panel to the aft
end.
d. If no crack indications are found, do the following:
(1) No more action is required by this service bulletin at any scribe lines that are determined
to be less than 0.001 inch deep. To determine if scribe lines are less than 0.001 inch
deep, they must be measured using the laser measurement procedure given in 777 NDT
Part 10, 53-30-01.
(2) Repair all scribe lines at Zone 2 lap joint locations that are more than 0.006 inch deep
before further flight. Disassemble the full length of the lap joint from the forward end of
the skin panel to the aft end and determine the full extent of any scribe lines and cracks.
Do surface HFEC inspections of the skin at any scribe lines found during disassembly
for cracks. Repair all scribe lines and cracks found in accordance with the Structural
Repair Manual, replace the damaged skin panel, or ask Boeing for repair data.
(3) If all scribe lines at Zone 2 lap joint locations are 0.006 inch deep or less, apply finish to
the skin to match adjacent structure. Document the location of all scribe damage that
was found at Zone 2 locations that was not repaired.
At or prior to the time given in Paragraph 1.E., Compliance, go to PART 10 and complete
all of the requirements of the Limited Return to Service (LRTS) plan for the scribed areas.
As an alternative, disassemble the full length of the lap joint from the forward end of the
skin panel to the aft end and determine the full extent of any scribe lines and cracks. Do
surface HFEC inspections of the skin at any scribe lines found during disassembly for
cracks. Repair all scribe lines and cracks found in accordance with the Structural Repair
Manual, replace the damaged skin panel, or ask Boeing for repair data.
6. Put the airplane back in a serviceable condition, and do the inspections in PART 4 (Zone 3), PART
5 (Zone 4) and PART 6 (Large Cargo Door Hinges) at the times specified in Paragraph 1.E.,
Compliance.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: August 07, 2008
777-53A0054Revision 1: November 04, 2010
37 of 91
BOEING SERVICE BULLETIN 777-53A0054

### Page 38

PART 4 - ZONE 3 INSPECTION
1. Group 1:
Affected Zone 3 locations are given in Figure 8.
2. Group 2:
Affected Zone 3 locations are given in Figure 9.
3. Group 3:
Affected Zone 3 locations are given in Figure 10.
4. Group 4:
Affected Zone 3 locations are given in Figure 11.
5. At or before the initial compliance threshold given in Paragraph 1.E., Compliance, do detailed
inspections for scribe lines at the affected lap joints in Zone 3 in accordance with PART 7.
6. If no scribe lines are found in Zone 3, no more inspections are necessary in Zone 3. In the areas
that were inspected, apply finish to the skin to match adjacent structure.
NOTE: To reduce the possibility of future scribing, Boeing recommends that no fillet seal be
applied at the lap joints.
7. If scribe lines are found in Zone 3, do the steps that follow:
a. Go to PART 9 and determine if the scribe damage is within the parameters of a "typical" scribe.
If the scribe damage is not within the parameters of a "typical" scribe, repair before further
flight. Repair in accordance with the Structural Repair Manual, replace the damaged skin
panel, or ask Boeing for repair data.
b. Do detailed, eddy current and ultrasonic inspections of all scribe lines that are within the
parameters of a "typical" scribe for cracks in accordance with Figure 19.
c. If any crack indications are found, do the steps that follow:
(1) Send a report about the crack indication to Boeing.
(2) Repair before further flight. Disassemble the full length of the lap joint from the forward
end of the skin panel to the aft end and determine the full extent of any scribe lines and
cracks. Do surface HFEC inspections of the skin at any scribe lines found during
disassembly for cracks. Repair all scribe lines and cracks found in accordance with the
Structural Repair Manual, replace the damaged skin panel, or ask Boeing for repair data.
An alternative repair is to repair using an approved method which repairs the entire
complete length of the lap joint, from the forward end of the scribed skin panel to the aft
end.
d. If no crack indications are found, do the following:
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: August 07, 2008
777-53A0054Revision 1: November 04, 2010
38 of 91
BOEING SERVICE BULLETIN 777-53A0054

### Page 39

(1) No more action is required by this service bulletin at any scribe lines that are determined
to be less than 0.001 inch deep. To determine if scribe lines are less than 0.001 inch
deep, they must be measured using the laser measurement procedure given in 777 NDT
Part 10, 53-30-01.
(2) Repair all scribe lines at Zone 3 lap joint locations that are more than 0.006 inch deep
before further flight. Disassemble the full length of the lap joint from the forward end of
the skin panel to the aft end and determine the full extent of any scribe lines and cracks.
Do surface HFEC inspections of the skin at any scribe lines found during disassembly
for cracks. Repair all scribe lines and cracks found in accordance with the Structural
Repair Manual, replace the damaged skin panel, or ask Boeing for repair data.
(3) If all scribe lines at Zone 3 lap joint locations are 0.006 inch deep or less, apply finish to
the skin to match adjacent structure. Document the location of all scribe damage that
was found at Zone 3 locations that was not repaired.
At or prior to the time given in Paragraph 1.E., Compliance, go to PART 10 and complete
all of the requirements of the Limited Return to Service (LRTS) plan for the scribed areas.
As an alternative, disassemble the full length of the lap joint from the forward end of the
skin panel to the aft end and determine the full extent of any scribe lines and cracks. Do
surface HFEC inspections of the skin at any scribe lines found during disassembly for
cracks. Repair all scribe lines and cracks found in accordance with the Structural Repair
Manual, replace the damaged skin panel, or ask Boeing for repair data.
8. Put the airplane back in a serviceable condition and do the inspections in PART 5 (Zone 4) and
PART 6 (Large Cargo Door Hinges) at the times specified in Paragraph 1.E., Compliance.
PART 5 - ZONE 4 INSPECTION
1. Group 1-2:
Affected Zone 4 locations are given in Figure 12.
2. Group 3-4:
Affected Zone 4 locations are given in Figure 13.
3. At or before the initial compliance threshold given in Paragraph 1.E., Compliance, do detailed
inspections for scribe lines at the affected lap joints in Zone 4 in accordance with PART 7. Do
inspections for scribe lines at the affected butt joints in Zone 4 in accordance with PART 8.
4. If no scribe lines are found in Zone 4, no more inspections are necessary in Zone 4. In the areas
that were inspected, apply finish to the skin and splice strap or splice chord to match adjacent
structure. Reseal the butt joints.
NOTE: To reduce the possibility of future scribing, Boeing recommends that no fillet seal be
applied at the lap joints. BMS 5-95 or BMS 5-142 sealant should be applied to the fuselage
butt joints.
5. At scribe lines found in Zone 4 lap joints, do the steps that follow:
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: August 07, 2008
777-53A0054Revision 1: November 04, 2010
39 of 91
BOEING SERVICE BULLETIN 777-53A0054

### Page 40

a. Go to PART 9 and determine if the scribe damage is within the parameters of a "typical" scribe.
If the scribe damage is not within the parameters of a "typical" scribe, repair before further
flight. Repair in accordance with the Structural Repair Manual, replace the damaged skin
panel, or ask Boeing for repair data.
b. Do detailed, eddy current and ultrasonic inspections of all lap joint scribe lines that are within
the parameters of a "typical" scribe for cracks in accordance with Figure 19.
c. If any crack indications are found, do the steps that follow:
(1) Send a report about the crack indication to Boeing.
(2) Repair before further flight. Disassemble the full length of the lap joint from the forward
end of the skin panel to the aft end and determine the full extent of any scribe lines and
cracks. Do surface HFEC inspections of the skin at any scribe lines found during
disassembly for cracks. Repair all scribe lines and cracks found in accordance with the
Structural Repair Manual, replace the damaged skin panel, or ask Boeing for repair data.
An alternative repair is to repair using an approved method which repairs the entire
complete length of the lap joint, from the forward end of the scribed skin panel to the aft
end.
d. If no crack indications are found, do the following:
(1) No more action is required by this service bulletin at any scribe lines that are determined
to be less than 0.001 inch deep. To determine if scribe lines are less than 0.001 inch
deep, they must be measured using the laser measurement procedure given in 777 NDT
Part 10, 53-30-01.
(2) Repair all scribe lines at Zone 4 lap joint locations that are more than 0.006 inch deep
before further flight. Disassemble the full length of the lap joint from the forward end of
the skin panel to the aft end and determine the full extent of any scribe lines and cracks.
Do surface HFEC inspections of the skin at any scribe lines found during disassembly
for cracks. Repair all scribe lines and cracks found in accordance with the Structural
Repair Manual, replace the damaged skin panel, or ask Boeing for repair data.
(3) If all scribe lines at Zone 4 lap joint locations are 0.006 inch deep or less, apply finish to
the skin to match adjacent structure. Document the location of all scribe damage that
was found at Zone 4 lap joint locations that were not repaired.
At or prior to the time given in Paragraph 1.E., Compliance, go to PART 10 and complete
all of the requirements of the Limited Return to Service (LRTS) plan for the scribed areas.
As an alternative, disassemble the full length of the lap joint from the forward end of the
skin panel to the aft end and determine the full extent of any scribe lines and cracks. Do
surface HFEC inspections of the skin at any scribe lines found during disassembly for
cracks. Repair all scribe lines and cracks found in accordance with the Structural Repair
Manual, replace the damaged skin panel, or ask Boeing for repair data.
6. At scribe lines found in Zone 4 butt joints, do the steps that follow:
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: August 07, 2008
777-53A0054Revision 1: November 04, 2010
40 of 91
BOEING SERVICE BULLETIN 777-53A0054

### Page 41

a. Go to PART 9 and determine if the scribe damage is within the parameters of a "typical" scribe.
If the scribe damage is not within the parameters of a "typical" scribe, repair before further
flight. Repair in accordance with the Structural Repair Manual, replace the cracked splice
strap or splice chord, or ask Boeing for repair data.
b. Do detailed and eddy current inspections of all butt joint scribe lines that are within the
parameters of a "typical" scribe for cracks in accordance with Figure 20.
c. If any crack indications are found, do the steps that follow:
(1) Send a report about the crack indication to Boeing.
(2) Repair before further flight. Disassemble the butt joint to determine the full extent of any
scribe lines and cracking. Do surface HFEC inspections of the splice strap or splice chord
at any scribe lines found during disassembly for cracks. Repair all scribe lines and cracks
found in accordance with the Structural Repair Manual, replace the cracked splice strap
or splice chord, or ask Boeing for repair data.
An alternative repair is to repair using an approved method which repairs the entire length
of the splice strap or splice chord.
d. If no crack indications are found, do the following:
(1) No more action is required by this service bulletin at any scribe lines that are determined
to be less than 0.001 inch deep. To determine if scribe lines are less than 0.001 inch
deep, they must be measured using the laser measurement procedure given in 777 NDT
Part 10, 53-30-01.
(2) Repair all scribe lines at Zone 4 butt joint locations that are more than 0.006 inch deep
before further flight. Disassemble the butt joint to determine the full extent of any scribe
lines and cracks. Do surface HFEC inspections of the splice strap or splice chord at any
scribe lines found during disassembly for cracks. Repair all scribe lines and cracks found
in accordance with the Structural Repair Manual, replace the cracked splice strap or
splice chord, or ask Boeing for repair data
(3) If all scribe lines at Zone 4 butt joint locations are 0.006 inch deep or less, apply finish to
the skin and splice strap or splice chord to match adjacent structure. Reseal the butt joint.
Document the location of all scribe damage that was found at Zone 4 butt joint locations
that were not repaired.
At or prior to the time given in Paragraph 1.E., Compliance, go to PART 10 and complete
all of the requirements of the Limited Return to Service (LRTS) plan for the scribed areas.
As an alternative, disassemble the butt joint to determine the full extent of any scribe
lines and cracks. Do surface HFEC inspections of the splice strap or splice chord at any
scribe lines found during disassembly for cracks. Repair all scribe lines and cracks found
in accordance with the Structural Repair Manual, replace the cracked splice strap or
splice chord, or ask Boeing for repair data.
7. Put the airplane back in a serviceable condition.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: August 07, 2008
777-53A0054Revision 1: November 04, 2010
41 of 91
BOEING SERVICE BULLETIN 777-53A0054

### Page 42

PART 6 - INSPECTION AT LARGE CARGO DOOR HINGES
1. Group 1, 3:
At or before the initial compliance threshold given in Paragraph 1.E., Compliance, remove the
sealant and paint around the large cargo door hinges and do detailed inspections for scribe lines
in accordance with Figure 17. The area of bare skin should be at least one inch wide, all around
the large cargo door hinge segments, on both the body and door sides. Use the sealant removal
instructions in Appendix A of this service bulletin.
2. Group 2, 4:
At or before the initial compliance threshold given in Paragraph 1.E., Compliance, remove the
sealant and paint around the large cargo door hinges and do detailed inspections for scribe lines
in accordance with Figure 18. The area of bare skin should be at least one inch wide, all around
the large cargo door hinge segments, on both the body and door sides. Use the sealant removal
instructions in Appendix A of this service bulletin.
3. If no scribe lines are found around the large cargo door hinges, no more inspections are necessary
in this area. In the areas that were inspected, apply finish to the skin to match adjacent structure.
4. If scribe lines are found around the large cargo door hinges, do the steps that follow:
a. Go to PART 9 and determine if the scribe damage is within the parameters of a "typical" scribe.
If the scribe damage is not within the parameters of a "typical" scribe, repair before further
flight. Repair in accordance with the Structural Repair Manual, replace the damaged skin
panel, or ask Boeing for repair data.
b. Group 1, 3:
Do detailed, eddy current and ultrasonic inspections of scribe lines that are within the
parameters of a "typical" scribe for cracks in accordance with Figure 21.
c. Group 2, 4:
Do detailed, eddy current and ultrasonic inspections of scribe lines that are within the
parameters of a "typical" scribe for cracks in accordance with Figure 22.
d. If any crack indications are found, do the steps that follow:
(1) Send a report about the crack indication to Boeing.
(2) Repair before further flight. Disassemble the hinge segments to determine the full extent
of the scribe lines and cracking. Do surface HFEC inspections of the skin at any scribe
lines found during disassembly for cracks. Repair all scribe lines and cracks found in
accordance with the Structural Repair Manual, replace the damaged skin panel, or ask
Boeing for repair data.
e. If no crack indications are found, do the following:
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: August 07, 2008
777-53A0054Revision 1: November 04, 2010
42 of 91
BOEING SERVICE BULLETIN 777-53A0054

### Page 43

(1) No more action is required by this service bulletin at any scribe lines that are determined
to be less than 0.001 inch deep. To determine if scribe lines are less than 0.001 inch
deep, they must be measured using the laser measurement procedure given in 777 NDT
Part 10, 53-30-01.
(2) Repair all scribe lines at large cargo door hinge locations that are more than 0.006 inch
deep before further flight. Disassemble the hinge segments to determine the full extent
of scribe lines and cracks. Do surface HFEC inspections of the skin at any scribe lines
found during disassembly for cracks. Repair all scribe lines and cracks found in accordance
with the Structural Repair Manual, replace the damaged skin panel, or ask Boeing for
repair data.
(3) If all scribe lines at large cargo door hinge locations are 0.006 inch deep or less, apply
finish to the skin to match adjacent structure. Document the location of all scribe damage
that was found at large cargo door hinge locations that was not repaired.
At or prior to the time given in Paragraph 1.E., Compliance, go to PART 10 and complete
all of the requirements of the Limited Return to Service (LRTS) plan for the scribed areas.
As an alternative, disassemble the hinge segments to determine the full extent of scribe
lines and cracks. Do surface HFEC inspections of the skin at any scribe lines found during
disassembly for cracks. Repair all scribe lines and cracks found in accordance with the
Structural Repair Manual, replace the damaged skin panel, or ask Boeing for repair data.
5. Put the airplane back in a serviceable condition.
PART 7 - INSPECTION AT FUSELAGE SKIN LAP JOINTS
1. Remove the sealant and paint from the lower edge of all affected lap joints. The bared area should
be at least one inch wide, as measured from the lower edge of the upper skin. Use the sealant
removal instructions in Appendix A of this service bulletin.
NOTE: At the Stringer 45 lap joint forward of STA 1035, the lap joint is reversed, and the sealant
removal and inspection is at the upper edge of the lap joint.
2. Do a detailed inspection of the fuselage skin for scribe lines in the area of bare skin at each affected
lap joint in accordance with Figure 15. The use of at least 10X magnifying lens are required for
this inspection.
NOTE: In areas near lap joints, scribe lines normally run parallel to the lap joint in the lower skin
along the edge of the upper skin. These scribe lines are typically within 0.25 inch of the
lower edge of the upper skin. In some cases, portions of the scribe lines may be directly
adjacent to or slightly under the lower edge of the upper skin. The ends of these scribe
lines sometimes may also turn slightly away from the lap joint.
PART 8 - INSPECTION AT FUSELAGE SKIN BUTT JOINTS
1. Remove the sealant from within the gap of the affected butt joints. Use the sealant removal
instructions in Appendix A of this service bulletin.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: August 07, 2008
777-53A0054Revision 1: November 04, 2010
43 of 91
BOEING SERVICE BULLETIN 777-53A0054

### Page 44

NOTE: It is recommended that the primer and paint, if present, not be removed from the butt
joint splice plate. If the primer is removed, do not use chemical stripper.
2. Do a detailed inspection of the butt joint splice plate for scribe lines in each affected area in
accordance with Figure 16. The use of at least 10X magnifying lens is required for this inspection.
NOTE: Scribe lines at butt joints are normally found on the splice plate in the gap between the
forward and aft skin edges and run along the butt joint.
PART 9 - IDENTIFICATION OF A "TYPICAL" SCRIBE
1. Determine if a scribe line is "typical":
A scribe line is defined as a narrow, shallow, distinct line of damage (up to 0.006 inch deep), usually
associated with the removal of a fillet or gap seal (lap joints and butt splices, respectively). Scribe
lines can be both tactile and non-tactile. Discoloration of the aluminum clad layer or small surface
imperfections do not qualify as a scribe. A lightning strike at a lap joint or butt splice does not
qualify as a scribe. In certain cases the scribe lines have also been associated with the trimming
of fuselage skin decals. Scribe lines that create a potential safety concern are generally long
continuous scribes or several adjacent scribes in a critical orientation at specific locations with
relatively high stresses. Figures are included in this Service Bulletin to depict typical scribe damage
found common to lap joints, butt joints, external doublers and large cargo door hinges.
Grinding, gouging, or other "non-typical" damage, which is more significant (deeper or locally more
extensive) than the typical scribing must be repaired before further flight. Localized scratches,
nicks and dents that might be induced in other areas of the fuselage skin during either manufacture
or maintenance operations are not considered scribes. This type of damage should be addressed
via the acceptable maintenance practices detailed in the Structural Repair Manual.
PART 10 - LIMITED RETURN TO SERVICE (LRTS) INSPECTION PLAN
1. At the time given in Paragraph 1.E., Compliance for the appropriate area:
a. Do detailed, eddy current and ultrasonic inspections of the scribe lines that were found at
external doubler locations or at lap joint locations for cracks in accordance with Figure 19.
b. Do detailed and eddy current inspections of the scribe lines that were found at butt joint
locations for cracks in accordance with Figure 20.
c. Group 1, 3:
Do detailed, eddy current and ultrasonic inspections of the scribe lines that were found at
large cargo door hinge locations for cracks in accordance with Figure 21.
d. Group 2, 4:
Do detailed, eddy current and ultrasonic inspections of the scribe lines that were found at
large cargo door hinge locations for cracks in accordance with Figure 22.
2. If any crack indications are found, do the steps that follow:
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: August 07, 2008
777-53A0054Revision 1: November 04, 2010
44 of 91
BOEING SERVICE BULLETIN 777-53A0054

### Page 45

a. Send a report about the crack indication to Boeing.
b. Repair before further flight. Repair in accordance with Parts 1 through Part 6, as appropriate.
3. If no crack indications are found, do one of the following:
a. Repair in accordance with Parts 1 through Part 6, as appropriate. This service bulletin requires
no more inspections for scribe lines that have been repaired.
b. Apply finish to the skin, splice straps or splice chords to match adjacent structure.
c. Reseal butt joints, if sealant was removed for inspection.
4. Put the airplane back to a serviceable condition. Do the inspections in PART 10 again at the
appropriate time from Paragraph 1.E., Compliance, for each affected scribed area. Inspections
are no longer necessary in areas that have been repaired.
PART 11 - MORE WORK REQUIRED AT DECAL LOCATIONS
1. The inspections that follow are only necessary on airplanes that have had external decals applied
or removed across affected lap joints, large cargo door hinges, or external doublers, but were
previously determined to not require inspections in accordance with the Original Issue of this
service bulletin, because they had never been stripped or repainted.
2. Determine the affected locations where external decals have been applied or removed across
affected lap joints, large cargo door hinges, or external doublers.
NOTE: These inspections are only necessary at locations where external decals have been
applied or removed across affected lap joints, large cargo door hinges, or external
doublers.
3. Use Figures 1 - 13, 17 and 18 to determine if the affected locations are External Doubler, Zone 1,
Zone 2, Zone 3, Zone 4, or Large Cargo Door Hinge locations.
4. Depending upon the affected locations, do inspections for scribe lines in accordance with PART
1, PART 2, PART 3, PART 4, PART 5, and PART 6, as applicable. Do inspections and repairs at
any scribe lines that are found in accordance with PART 1, PART 2, PART 3, PART 4, PART 5,
and PART 6, as applicable.
5. Put the airplane back to a serviceable condition.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: August 07, 2008
777-53A0054Revision 1: November 04, 2010
45 of 91
BOEING SERVICE BULLETIN 777-53A0054

### Page 46 (OCR)

BOEING SERVICE BULLETIN 777-53A0054
This Figure applies only to: Group 1.
- 14R
STA  1832
STA  1434  AREA B
STA  1035
1539736
FIGURE 1: EXTERNAL DOUBLER INSPECTION LOCATIONS - GROUP 1 AIRPLANES
(SHEET 1 OF 1)
Original Issue: August 07, 2008
Revision 1 November 04, 2010  777-53A0054
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.  46 of 91

### Page 47 (OCR)

BOEING SERVICE BULLETIN 777-53A0054
This Figure applies only to: Group 2.
S-14R  20L
1 5801685 1722
STA  1035
1539802
FIGURE 2: EXTERNAL DOUBLER INSPECTION LOCATIONS - GROUP 2 AIRPLANES
(SHEET 1 OF 1)
Original Issue: August 07, 2008
Revision 1 November 04, 2010  777-53A0054
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.  47 of 91

### Page 48 (OCR)

BOEING SERVICE BULLETIN 777-53A0054
This Figure applies only to: Group 3.
STA
STA  634 STA  STA  STA
246  655  825  1035
+210
S-45R
S-34R
S-24R
S-14R
• S-5R
S-5L
• S-14L
S-24L
S-34L
S-45L
STA  STA  STA  STA STA  STA  STA
1035  1434  1434  580 168!  1832  2150
+189
S-45R
S-34R
S-24R
S-20R
S-14R
S-5R
S-5L
S-14L
S-20L
S-24L
S-34L
S-45L
AREA A
AREA B  1539808
FIGURE 3: EXTERNAL DOUBLER INSPECTION LOCATIONS - GROUP 3 AIRPLANES
(SHEET 1 OF 1)
Original Issue: August 07, 2008
Revision 1 November 04, 2010  777-53A0054
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.  48 of 91

### Page 49 (OCR)

BOEING SERVICE BULLETIN 777-53A0054
This Figure applies only to: Group 4.
STA  STA  STA  STA
246  655  825  1035
+210
S-45R
S-34R
S-24R
S-14R
S-5R
• S-5L
S-14L
S-24L
S-34L
S-45L
STA  STA  STA  STA  STA  STA  STA
1035  1434  1434  1580 1685  1832  2150
+189
S-45R
S-34R
S-24R
S-20R
S-14R
S-5R
• S-5L
S-14L
S-20L
S-24L
S-34L
S-45L
AREA A
AREA B  1549371
FIGURE 4: EXTERNAL DOUBLER INSPECTION LOCATIONS - GROUP 4 AIRPLANES
(SHEET 1 OF 1)
Original Issue: August 07, 2008
Revision 1 November 04, 2010  BOEING PROPRIETARY -  777-53A0054
Copyright © Unpublished Work - See page 1 for details.  49 of 91

### Page 50 (OCR)

BOEING SERVICE BULLETIN 777-53A0054
This Figure applies only to: Group 3-4.
STA  STA  STA  STA  STA
1035  1434  1434  1832  2150
+189
S-45R
S-34R
0000  0000000000  00000000000  0000000000000000000  S-24R
S-14R
S-5R
S-5L
- S-14L
0000  0000000000 00000000000
- S-24L
S-34L
S-45L  1549366
FIGURE 5: ZONE 1 - GROUP 3 AND 4 AIRPLANES
(SHEET 1 OF 1)
Original Issue: August 07, 2008
Revision 1 November 04, 2010  777-53A0054
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.  50 of 91

### Page 51 (OCR)

BOEING SERVICE BULLETIN 777-53A0054
This Figure applies only to: Group 1-2.
STA  1832  00000000000000000  00000000000000000
STA  STA  1434  1035  000000000000  0 0000000 000000000  0 0000000 000000000 000000000000
0000000000000  0000000000000 0
1539848
FIGURE 6: ZONE 2 - GROUP 1 AND 2 AIRPLANES
(SHEET 1 OF 1)
Original Issue: August 07, 2008
Revision 1 November 04, 2010  BOEING PROPRIETARY -  777-53A0054
Copyright © Unpublished Work - See page 1 for details.  51 of 91

### Page 52 (OCR)

BOEING SERVICE BULLETIN 777-53A0054
This Figure applies only to: Group 3-4.
STA  STA  STA  STA
246  655  825  1035
+210
S-45R
S-34R
o o
0000000000000 0  000000000  000 000  S-24R
• S-14R
• S-5R
S-5L
S-14L
0000000000000 0  000000000 000 000
S-24L
S-34L
S-45L
STA
571
STA  STA  STA  STA  STA
1035  1434  1434  1832  2150
+189
S-45R
S-34R
0000  0000000000  00000000000  00000000000000000000  S-24R
S-14R
S-5R
S-5L
S-14L
0000  0000000000  00000000000  0000000000000000000
S-24L
S-34L
S-45L
1539946
FIGURE 7: ZONE 2 - GROUP 3 AND 4 AIRPLANES
(SHEET 1 OF 1)
Original Issue: August 07, 2008
Revision 1 November 04, 2010  777-53A0054
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.  52 of 91

### Page 53 (OCR)

BOEING SERVICE BULLETIN 777-53A0054
This Figure applies only to: Group 1.
• S-24R
STA  1832  0000000000000000000  000000000000000000
STA  STA  1434  1035  000000000000  000000000  0 0000000 000000000 000000000000
• 0000000
FIGURE 8: ZONE 3 - GROUP 1 AIRPLANES
(SHEET 1 OF 1)
Original Issue: August 07, 2008
Revision 1 November 04, 2010  BOEING PROPRIETARY -  777-53A0054
Copyright © Unpublished Work - See page 1 for details.  53 of 91

### Page 54 (OCR)

BOEING SERVICE BULLETIN 777-53A0054
This Figure applies only to: Group 2.
STA  1832  00000000000000000000  0000000000000
STA  STA  GEOL  DEDL  000000000000 000000000  0 0000000 000000000 000000000000
0 0000000
0000000000000  000000000000
FIGURE 9: ZONE 3 - GROUP 2 AIRPLANES
(SHEET 1 OF 1)
Original Issue: August 07, 2008
Revision 1 November 04, 2010  BOEING PROPRIETARY -  777-53A0054
Copyright © Unpublished Work - See page 1 for details.  54 of 91

### Page 55 (OCR)

BOEING SERVICE BULLETIN 777-53A0054
This Figure applies only to: Group 3.
STA  STA  I STA  STA
246  655  825  1035
+210
S-45R
S-34R
• o
0000000000000 0  0 000000000 000 000  S-24R
S-14R
S-5R
• S-5L
S-14L
0000000000000 0  0 000000000 000 000
S-45L
STA
571
STA  STA  STA  STA  V1S
1035  1434  1434  1832  2150
+189
S-45R
S-34R
0000  0000000000  00000000000  0000000000000000000  S-24R
S-14R
S-5R
S-5L
S-14L
0000  0000000000  00000000000  00000000000000000000
S-24L
S-34L
S-45L
FIGURE 10: ZONE 3 - GROUP 3 AIRPLANES
(SHEET 1 OF 1)
Original Issue: August 07, 2008
Revision 1 November 04, 2010  BOEING PROPRIETARY -  777-53A0054
Copyright © Unpublished Work - See page 1 for details.  55 of 91

### Page 56 (OCR)

BOEING SERVICE BULLETIN 777-53A0054
This Figure applies only to: Group 4.
STA  STA  STA  STA
246  655  825  1035
+210
S-45R
S-34R
• o
0000000000000 0  000000000  000 000  S-24R
• S-14R
• S-5R
S-5L
S-14L
0000000000000 0  0 000000000 000 000  S-24L
S-34L
S-45L
STA
571
STA  STA  STA  STA  STA
1035  1434  1434  1832  2150
+189
S-45R
S-34R
0000  0000000000  00000000000  00000000000000000000  S-24R
S-14R
S-5R
S-5L
S-14L
0000  0000000000  00000000000  00000000000000000000
S-24L
S-34L
• S-45L
FIGURE 11: ZONE 3 - GROUP 4 AIRPLANES
(SHEET 1 OF 1)
Original Issue: August 07, 2008
Revision 1 November 04, 2010  BOEING PROPRIETARY -  777-53A0054
Copyright © Unpublished Work - See page 1 for details.  56 of 91

### Page 57 (OCR)

BOEING SERVICE BULLETIN 777-53A0054
This Figure applies only to: Group 1-2.
VIS  00000000000000000000  00000000000000000000
VIS  VIS  DEDI  GEOL  000000000000  000000000 0000000 0  000000000000 000000000 0000000 0
0000000000000  0 0000000000000
926691
FIGURE 12: ZONE 4 - GROUP 1 AND 2 AIRPLANES
(SHEET 1 OF 1)
Original Issue: August 07, 2008
Revision 1 November 04, 2010  BOEING PROPRIETARY -  777-53A0054
Copyright © Unpublished Work - See page 1 for details.  57 of 91

### Page 58 (OCR)

BOEING SERVICE BULLETIN 777-53A0054
This Figure applies only to: Group 3-4.
STA  STA  STA  STA
246  655  825  1035
+210
S-45R
S-34R
o o
0000000000000 0  000000000  000 000  S-24R
- S-14R
- S-5R
S-5L
• S-14L
0000000000000 0  0 000000000 000 000
S-24L
S-34L
S-45L
STA  STA  STA  STA  STA
1035  1434  1434  1832  2150
+189
• S-45R
S-34R
0000  0000000000  00000000000  00000000000000000000  S-24R
S-14R
S-5R
S-5L
S-14L
0000  0000000000  00000000000  00000000000000000000
S-24L
S-34L
S-45L
1539984
FIGURE 13: ZONE 4 - GROUP 3 AND 4 AIRPLANES
(SHEET 1 OF 1)
Original Issue: August 07, 2008
Revision 1 November 04, 2010  777-53A0054
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.  58 of 91

### Page 59

The step numbers shown below agree with the numbers shown in the circle symbols in the figure.
NOTE: Use care to not blend out any scribe lines that may exist when cleaning the affected areas.1.
2. Remove all sealant and paint from around the periphery of the doubler to do the inspections
that follow.
3. Inspect around the entire periphery of the external repair doubler.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
Detailed inspection
for scribe lines. At
affected locations,
using at least 10X
magnification, or use
the laser inspection
tool in accordance
with 777 NDT Part
10, 53-30-01.
--SkinInspect1
If scribe lines are
found. Use an opti-
cal micrometer or
the laser measure-
ment tool in accor-
dance with 777 NDT
Part 10, 53-30-01.
--Scribe DepthMeasure2
FIGURE 14: INSPECTION FOR SCRIBE LINES AT EXTERNAL REPAIR DOUBLER LOCATIONS
(SHEET 1 OF 1)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: August 07, 2008
777-53A0054Revision 1 November 04, 2010
59 of 91
BOEING SERVICE BULLETIN 777-53A0054

### Page 60

The step number shown below agrees with the number shown in the circle symbols in the figure.
NOTE: Use care to not blend out any scribe lines that may exist when cleaning the affected areas.1.
2. Remove all sealant and paint from the affected areas to do the inspections that follow.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
Detailed inspection
for scribe lines. At
affected locations,
using at least 10X
magnification, or use
the laser inspection
tool in accordance
with 777 NDT Part
10, 53-30-01..
--SkinInspect1
If scribe lines are
found. Use an opti-
cal micrometer or
the laser measure-
ment tool in accor-
dance with 777 NDT
Part 10, 53-30-01.
--Scribe DepthMeasure2
FIGURE 15: INSPECTION FOR SCRIBE LINES AT LAP JOINT LOCATIONS
(SHEET 1 OF 1)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: August 07, 2008
777-53A0054Revision 1 November 04, 2010
60 of 91
BOEING SERVICE BULLETIN 777-53A0054

The text continues at https://openairdocs.org/service-documents/boeing/777-53a0054/file/7fba08d29389.md?from=61

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
