# Boeing Alert Requirements Bulletin 777-57A0128 RB: No revision named, part 3 of 4

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2026-1339, the docket of a proposed AD (Federal Register 2026-03782). Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Alert Requirements Bulletin 777-57A0128 RB](https://openairdocs.org/service-documents/boeing/777-57a0128-rb.md)
- Title as filed: 777-57A0128_RB_00- part 3
- Pages: 24
- PDF: https://openairdocs.org/files/sha256/ce/3c/ce3ca85029b064f05d201168598ceee4179ee930abdb3fb6dad0f9776dfb7008
- Page: https://openairdocs.org/service-documents/boeing/777-57a0128-rb/file/ce3ca85029b0

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

FIGURE 12: LEFT MAIN LANDING GEAR - SUPPORT BEAM LOWER STABILIZER BRACE AFT FITTING
- REPLACEMENT
(SHEET 2 OF 8)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: June 02, 2025
777-57A0128 RB
97 of 144
REQUIREMENTS BULLETIN 777-57A0128
ALERTALERT

### Page 2

FIGURE 12: LEFT MAIN LANDING GEAR - SUPPORT BEAM LOWER STABILIZER BRACE AFT FITTING
- REPLACEMENT
(SHEET 3 OF 8)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: June 02, 2025
777-57A0128 RB
98 of 144
REQUIREMENTS BULLETIN 777-57A0128
ALERTALERT

### Page 3 (OCR)

REQUIREMENTS BULLETIN 777-57A0128
ALERT  ALERT
MAIN LANDING GEAR
SUPPORT BEAM
SHIM
(22)
9) 6 LOCATIONS
14 16
15 16) 4 LOCATIONS
MAIN LANDING
GEAR SUPPORT
BEAM
FWD
VIEW IN THE DOWN DIRECTION
(TYPICAL)
B-B
NBD
6 LOCATIONS
VIEW IN THE AFT DIRECTION
(TYPICAL)
C-C
2 LOCATIONS 20
MAIN LANDING
4 LOCATIONS (19) 21  GEAR SUPPORT
BEAM
(18-
INBD
VIEW IN THE AFT DIRECTION
(TYPICAL)  D-D  3079088
FIGURE 12: LEFT MAIN LANDING GEAR - SUPPORT BEAM LOWER STABILIZER BRACE AFT FITTING
- REPLACEMENT
(SHEET 4 OF 8)
Original Issue: June 02, 2025
Export Controlled ECCN: 9E991  777-57A0128 RB
See page 1 for details  99 of 144

### Page 4

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
More DataQtyIdentificationNameTaskStep
-1NAS1805-4NUTRemove1
-1115W1672-10RETAINER CAPRemove2
(a)(b)1BACB30MR4K71BOLTRemove3
-1115W1672-14RETAINER CAPRemove4
-1BACN10JC9CMNUTRemove5
-1115W1672-9RETAINER CAPRemove6
-1115W1671-17PIN, LOWER AFTRemove7
---LOWER STABILIZER
BRACE
Disconnect8
If not already re-
moved.
6-FASTENERSRemove9
(a)(b)
Keep the left MLG
Support Beam Low-
er Stabilizer Brace
AFT Fitting to use
for hole transfer into
the new fitting.
1-MLG SUPPORT BEAM
LOWER STABILIZER
BRACE AFT FITTING
Remove10
-1-SHIMRemove11
(c)--MLG SUPPORT BEAMClean12
(d)--MLG SUPPORT BEAMInspect13
Drill to Hole Diame-
ter 0.3745 - 0.3755
inch (e)(f)(g)
-115W1613U17FITTING AYDrill14
Drill to Hole Diame-
ter 0.312 - 0.313
inch (e)(f)(g)
-115W1613U17FITTING AYDrill15
Break all sharp
edges on drilled
holes.
6-FASTENER HOLESDeburr16
-1115W1613U17FITTING AYPut / Hold17
(i)(j)1BACS40R035C040FSHIM STOCKPut / Hold
(h)-BMS 5-95SEALANTApply18
FIGURE 12: LEFT MAIN LANDING GEAR - SUPPORT BEAM LOWER STABILIZER BRACE AFT FITTING
- REPLACEMENT
(SHEET 5 OF 8)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: June 02, 2025
777-57A0128 RB
100 of 144
REQUIREMENTS BULLETIN 777-57A0128
ALERTALERT

### Page 5

More DataQtyIdentificationNameTaskStep
-1115W1613U17FITTING AYInstall (New)19
(j)1BACS40R035C040FSHIM STOCKInstall (New)
(b)(k)(l)4BACB30US5K32BOLT, 12 PT HEADInstall (New)
Install under bolt
head.
4BACW10BP5CDCSK WASHERInstall (New)
Install under nut.4BACW10BP5DPWASHER-PLAINInstall (New)
Torque nut to 243 to
258 inch-lbs.
4BACN10HR5CDNUTInstall (New)
(m)
(b)(k)(l)2BACB30US6K32BOLT, 12 PT HEADInstall (New)20
Install under bolt
head.
2BACW10BP6CDWASHER, PLAINInstall (New)
Install under nut.2BACW10BP6DPWASHERInstall (New)
Torque nut to 485 to
515 inch-lbs.
2BACN10HR6CDSELF-LOCKING NUTInstall (New)
(m)
(n)4BACN10HR5CDNUTTorque21
(n)2BACN10HR6CDSELF-LOCKING NUTTorque
-2AS15001-1PFITTING, LUBRICA-
TION
Install (New)22
---LOWER STABILIZER
BRACE
Connect23
-1115W1671-17PIN, LOWER AFTInstall (New)24
-1115W1672-9RETAINER CAPInstall (New)25
Torque nut to 300 to
400 inch-lbs.
1BACN10JC9CMNUTInstall (New)26
-1115W1672-14RETAINER CAPInstall (New)27
(b)(l)(o)1BACB30MR4A71BOLTInstall (New)28
-1115W1672-10RETAINER CAPInstall (New)29
Torque nut to 82 to
88 inch-lbs.
1BACN11Z4CKNUTInstall (New)30
(p)-BMS 3-33GREASEApply31
(q)-115W1613U17FITTING AYIdentify32
(a) Make a note of the fastener orientation for installation.
FIGURE 12: LEFT MAIN LANDING GEAR - SUPPORT BEAM LOWER STABILIZER BRACE AFT FITTING
- REPLACEMENT
(SHEET 6 OF 8)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: June 02, 2025
777-57A0128 RB
101 of 144
REQUIREMENTS BULLETIN 777-57A0128
ALERTALERT

### Page 6

More DataQtyIdentificationNameTaskStep
(b) Refer to 777-200 SRM 51-40-02, 777-300 SRM 51-40-02, or 777F SRM 51-40-02 as an accepted proce-
dure.
(c) Use non-metallic tools to remove sealant from the upper and lower surfaces of the left MLG Support Beam
where the existing left MLG Support Beam Lower Stabilizer Brace AFT Fitting and shim were installed.
Refer to SOPM 20-30-03 as an accepted procedure.
(d) Do an open hole High Frequency Eddy Current (HFEC) inspection of the MLG Support Beam for any
crack, in accordance with 777 NDT Manual Part 6, 51-00-02. If any crack is found, contact The Boeing
Company for repair instructions and do the repair.
(e) Use Special Tool MIT115W1613 to transfer hole locations from the existing left MLG Support Beam
Lower Stabilizer Brace AFT Fitting to new blank AFT Fitting in accordance with the MIT115W1613 tool
use instructions.
(f) As an alternative to the MIT115W1613 tool use instructions, it is acceptable to use a mill machine to map
and transfer close ream hole locations from the existing left MLG Support Beam Lower Stabilizer Brace
AFT Fitting to new blank AFT Fitting. Refer to 777-200 SRM 51-40-05, 777-300 SRM 51-40-05, or 777F
SRM 51-40-05 as an accepted procedure.
(g) It is acceptable to oversize fastener holes, within the left MLG Support Beam Lower Stabilizer Brace AFT
Fitting and left MLG Support Beam, to 1st oversized close ream fastener holes if nominal close ream
fastener hole diameters can not be achieved. Additional oversize fasteners have been provided in
005W0183-12 kit. Refer to 777-200 SRM 51-40-05, 777-300 SRM 51-40-05, or 777F SRM 51-40-05 as
an accepted procedure.
(h) Apply faying surface seal using BMS 5-95 sealant on all mating surfaces. Refer to SOPM 20-50-19 as
an accepted procedure.
(i) Install shim between the upper flange of the left MLG Support Beam Lower Stabilizer Brace AFT Fitting
and the left MLG Support Beam. Remove 0.003 inch laminations as required to adjust thickness. Trim
profile of shim. Taper shim if required. Maintain edge condition. Refer to SOPM 20-50-20 as an accepted
procedure.
(j) Maximum pull-up after shim installation to be 0.005 inch.
(k) Install fasteners wet with BMS 5-95 sealant. Refer to SOPM 20-50-19 Method 2 as an accepted procedure.
(l) Install fasteners following the orientation noted during removal.
(m) Torque the nuts with a minimum of 60 minutes of squeeze-out life left in the fastener and fay surface
sealant. Refer to 777-200 SRM 51-40-02, 777-300 SRM 51-40-02, or 777F SRM 51-40-02 as an accepted
procedure.
FIGURE 12: LEFT MAIN LANDING GEAR - SUPPORT BEAM LOWER STABILIZER BRACE AFT FITTING
- REPLACEMENT
(SHEET 7 OF 8)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: June 02, 2025
777-57A0128 RB
102 of 144
REQUIREMENTS BULLETIN 777-57A0128
ALERTALERT

### Page 7

More DataQtyIdentificationNameTaskStep
(n) Re-apply torque to the nuts no sooner than:
- 10 minutes after the initial torque application, if Class B-1/2 or B-2 sealant was used.
- 10 minutes after the initial torque application, if Class C-20, C-24 or C-48 sealant was used.
- 60 minutes after the initial torque application, if sealant with a squeeze-out life longer than 48 hours was
used.
Make sure torque re-application is done before the squeeze-out life of the fastener and fay surface sealant
expires. Refer to 777-200 SRM 51-40-02, 777-300 SRM 51-40-02, or 777F SRM 51-40-02 as an accepted
procedure.
(o) Install fasteners wet with BMS 5-95 sealant. Refer to SOPM 20-50-19 as an accepted procedure.
(p) Lubricate the grease fittings with BMS 3-33 grease after installation of the left MLG Support Beam Lower
Stabilizer Brace AFT Fitting. Refer to 777 AMM 12-21-11 as an accepted procedure.
(q) Apply the service bulletin number to the left MLG Support Beam Lower Stabilizer Brace AFT Fitting at
this area only. Refer to SOPM 20-50-10, Code M as an accepted procedure.
FIGURE 12: LEFT MAIN LANDING GEAR - SUPPORT BEAM LOWER STABILIZER BRACE AFT FITTING
- REPLACEMENT
(SHEET 8 OF 8)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: June 02, 2025
777-57A0128 RB
103 of 144
REQUIREMENTS BULLETIN 777-57A0128
ALERTALERT

### Page 8 (OCR)

REQUIREMENTS BULLETIN 777-57A0128
ALERT  ALERT
FWD
MAIN LANDING GEAR
LOWER STABILIZER BRACE  3075990
FIGURE 13: RIGHT MAIN LANDING GEAR - SUPPORT BEAM LOWER STABILIZER BRACE AFT FITTING,
MLG SUPPORT BEAM AND STABILIZER BRACE - DETAILED INSPECTION (DET)
(SHEET 1 OF 4)
Original Issue: June 02, 2025
Export Controlled ECCN: 9E991  777-57A0128 RB
See page 1 for details  104 of 144

### Page 9 (OCR)

REQUIREMENTS BULLETIN 777-57A0128
ALERT  ALERT
MAIN LANDING GEAR
SUPPORT BEAM
LOWER STABILIZER
• BRACE
FWD
WING REAR SPAR
ASSEMBLY
MAIN LANDING GEAR  VIEW IN THE INBOARD DIRECTION
SUPPORT BEAM LOWER  (TYPICAL)
FITTING  STABILIZER BRACE AFT  A-A
MAIN LANDING GEAR
SUPPORT BEAM
5.10
4.90
2.60
2.40
- SHIM
5.10
4.90
LOWER STABILIZER
BRACE
MAIN LANDING GEAR
SUPPORT BEAM LOWER
STABILIZER BRACE AFT  - WD
FITTING
DETAILED INSPECTION  VIEW IN THE DOWN DIRECTION  (TYPICAL)  3075996
B-B
FIGURE 13: RIGHT MAIN LANDING GEAR - SUPPORT BEAM LOWER STABILIZER BRACE AFT FITTING,
MLG SUPPORT BEAM AND STABILIZER BRACE - DETAILED INSPECTION (DET)
(SHEET 2 OF 4)
Original Issue: June 02, 2025
Export Controlled ECCN: 9E991  777-57A0128 RB
See page 1 for details  105 of 144

### Page 10 (OCR)

REQUIREMENTS BULLETIN 777-57A0128
ALERT  ALERT
MAIN LANDING GEAR
SUPPORT BEAM
LOWER
STABILIZER BRACE
5.10
4.90
2.60
2.40
₴
MAIN LANDING GEAR
SUPPORT BEAM
LOWER STABILIZER
BRACE AFT FITTING
5.10
4.90
5.10
.90
FWD
VIEW IN THE UP DIRECTION
(TYPICAL)
C-C
DETAILED INSPECTION  3075998
FIGURE 13: RIGHT MAIN LANDING GEAR - SUPPORT BEAM LOWER STABILIZER BRACE AFT FITTING,
MLG SUPPORT BEAM AND STABILIZER BRACE - DETAILED INSPECTION (DET)
(SHEET 3 OF 4)
Original Issue: June 02, 2025
Export Controlled ECCN: 9E991  777-57A0128 RB
See page 1 for details  106 of 144

### Page 11

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
More DataQtyIdentificationNameTaskStep
(a)--MLG SUPPORT BEAM
LOWER STABILIZER
BRACE AFT FITTING
Inspect1
(b)(c)--MLG SUPPORT BEAMInspect2
(b)(c)--LOWER STABILIZER
BRACE
Inspect
(a) Do a DET of the right MLG Support Beam Lower Stabilizer Brace AFT Fitting for any crack.
(b) Do a DET of the right MLG Support Beam and Lower Stabilizer Brace for any damage.
(c) Damage is defined as any abrasion, dent, scratch, gouge, nick or corrosion in the metallic structure.
FIGURE 13: RIGHT MAIN LANDING GEAR - SUPPORT BEAM LOWER STABILIZER BRACE AFT FITTING,
MLG SUPPORT BEAM AND STABILIZER BRACE - DETAILED INSPECTION (DET)
(SHEET 4 OF 4)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: June 02, 2025
777-57A0128 RB
107 of 144
REQUIREMENTS BULLETIN 777-57A0128
ALERTALERT

### Page 12 (OCR)

REQUIREMENTS BULLETIN 777-57A0128
ALERT  ALERT
FWD
MAIN LANDING GEAR
LOWER STABILIZER BRACE  3079101
FIGURE 15: RIGHT MAIN LANDING GEAR - SUPPORT BEAM LOWER STABILIZER BRACE AFT FITTING
AND MLG SUPPORT BEAM - OPEN HOLE HIGH FREQUENCY EDDY CURRENT (HFEC) INSPECTION
(SHEET 1 OF 3)
Original Issue: June 02, 2025
777-57A0128 RB
Export Controlled ECCN: 9E991
See page 1 for details  108 of 144

### Page 13 (OCR)

REQUIREMENTS BULLETIN 777-57A0128
ALERT  ALERT
MAIN LANDING GEAR
SUPPORT BEAM
LOWER STABILIZER
BRACE
FWD  WING REAR SPAR
ASSEMBLY
MAIN LANDING GEAR  VIEW IN THE INBOARD DIRECTION
SUPPORT BEAM LOWER  (TYPICAL)
FITTING  STABILIZER BRACE AFT  A-A
MAIN LANDING GEAR
SUPPORT BEAM
6 LOCATIONS  SHIM
LOWER STABILIZER
BRACE
MAIN LANDING GEAR
SUPPORT BEAM LOWER
STABILIZER BRACE AFT
FITTING
VIEW IN THE DOWN DIRECTION  9-8  3079103
FIGURE 15: RIGHT MAIN LANDING GEAR - SUPPORT BEAM LOWER STABILIZER BRACE AFT FITTING
AND MLG SUPPORT BEAM - OPEN HOLE HIGH FREQUENCY EDDY CURRENT (HFEC) INSPECTION
(SHEET 2 OF 3)
Original Issue: June 02, 2025
Export Controlled ECCN: 9E991  777-57A0128 RB
See page 1 for details  109 of 144

### Page 14

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
More DataQtyIdentificationNameTaskStep
(a)6-FASTENER HOLEInspect1
(a) Do an open hole HFEC inspection of the upper and lower flanges of the right MLG Support Beam Lower
Stabilizer Brace AFT Fitting and MLG Support Beam for any crack, in accordance with 777 NDT Manual
Part 6, 51-00-02.
FIGURE 15: RIGHT MAIN LANDING GEAR - SUPPORT BEAM LOWER STABILIZER BRACE AFT FITTING
AND MLG SUPPORT BEAM - OPEN HOLE HIGH FREQUENCY EDDY CURRENT (HFEC) INSPECTION
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: June 02, 2025
777-57A0128 RB
110 of 144
REQUIREMENTS BULLETIN 777-57A0128
ALERTALERT

### Page 15 (OCR)

REQUIREMENTS BULLETIN 777-57A0128
ALERT  ALERT
FWD
MAIN LANDING GEAR
LOWER STABILIZER BRACE  3075991
FIGURE 16: RIGHT MAIN LANDING GEAR - SUPPORT BEAM LOWER STABILIZER BRACE AFT FITTING
- ULTRASONIC (UT) INSPECTION
(SHEET 1 OF 3)
Original Issue: June 02, 2025
Export Controlled ECCN: 9E991  777-57A0128 RB
See page 1 for details  111 of 144

### Page 16 (OCR)

REQUIREMENTS BULLETIN 777-57A0128
ALERT  ALERT
MAIN LANDING GEAR
SUPPORT BEAM
LOWER STABILIZER
/ BRACE
FWD
WING REAR SPAR
MAIN LANDING GEAR  VIEW IN THE INBOARD DIRECTION  ASSEMBLY
SUPPORT BEAM LOWER  (TYPICAL)
FITTING  STABILIZER BRACE AFT  A-A
MAIN LANDING GEAR
SUPPORT BEAM
SHIM
LOWER STABILIZER
BRACE
MAIN LANDING GEAR
SUPPORT BEAM LOWER
STABILIZER BRACE AFT
FITTING
ULTRASONIC INSPECTION  VIEW IN THE DOWN DIRECTION  (TYPICAL)  3075997
B-B
FIGURE 16: RIGHT MAIN LANDING GEAR - SUPPORT BEAM LOWER STABILIZER BRACE AFT FITTING
- ULTRASONIC (UT) INSPECTION
(SHEET 2 OF 3)
Original Issue: June 02, 2025
Export Controlled ECCN: 9E991  777-57A0128 RB
See page 1 for details  112 of 144

### Page 17

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
More DataQtyIdentificationNameTaskStep
(a)--MLG SUPPORT BEAM
LOWER STABILIZER
BRACE AFT FITTING
Inspect1
(a) Do a UT inspection of the upper and lower flange surfaces of the right MLG Support Beam Lower Stabi-
lizer Brace AFT Fitting for any crack, in accordance with 777 NDT Manual Part 4, 57-54-04. If any crack
is found, it is not required to do the follow-on Open Hole HFEC Inspection in accordance with 777 NDT
Manual Part 4, 57-54-04.
FIGURE 16: RIGHT MAIN LANDING GEAR - SUPPORT BEAM LOWER STABILIZER BRACE AFT FITTING
- ULTRASONIC (UT) INSPECTION
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: June 02, 2025
777-57A0128 RB
113 of 144
REQUIREMENTS BULLETIN 777-57A0128
ALERTALERT

### Page 18 (OCR)

REQUIREMENTS BULLETIN 777-57A0128
ALERT  ALERT
This Figure applies only to: Group 1.
FWD
MAIN LANDING GEAR
LOWER STABILIZER BRACE  3075992
FIGURE 21: RIGHT MAIN LANDING GEAR - SUPPORT BEAM LOWER STABILIZER BRACE AFT FITTING
- REPLACEMENT
(SHEET 1 OF 7)
Original Issue: June 02, 2025
777-57A0128 RB
Export Controlled ECCN: 9E991
See page 1 for details  114 of 144

### Page 19

FIGURE 21: RIGHT MAIN LANDING GEAR - SUPPORT BEAM LOWER STABILIZER BRACE AFT FITTING
- REPLACEMENT
(SHEET 2 OF 7)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: June 02, 2025
777-57A0128 RB
115 of 144
REQUIREMENTS BULLETIN 777-57A0128
ALERTALERT

### Page 20

FIGURE 21: RIGHT MAIN LANDING GEAR - SUPPORT BEAM LOWER STABILIZER BRACE AFT FITTING
- REPLACEMENT
(SHEET 3 OF 7)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: June 02, 2025
777-57A0128 RB
116 of 144
REQUIREMENTS BULLETIN 777-57A0128
ALERTALERT

### Page 21 (OCR)

REQUIREMENTS BULLETIN 777-57A0128
ALERT  ALERT
MAIN LANDING GEAR
/ SUPPORT BEAM
SHIM
→20 29
MAIN LANDING
6 LOCATIONS  GEAR SUPPORT
BEAM
14 15)
6 LOCATIONS
INBD
6 LOCATIONS
FWD  VIEW IN THE AFT DIRECTION
(TYPICAL)
VIEW IN THE DOWN DIRECTION  C-C
(TYPICAL)
B-B
MAIN LANDING  6 LOCATIONS
GEAR SUPPORT
BEAM  18/19
INBD
VIEW IN THE AFT DIRECTION
(TYPICAL)  D-D  3079074
FIGURE 21: RIGHT MAIN LANDING GEAR - SUPPORT BEAM LOWER STABILIZER BRACE AFT FITTING
- REPLACEMENT
(SHEET 4 OF 7)
Original Issue: June 02, 2025
Export Controlled ECCN: 9E991  777-57A0128 RB
See page 1 for details  117 of 144

### Page 22

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
More DataQtyIdentificationNameTaskStep
-1NAS1805-4NUTRemove1
-1115W1672-10RETAINER CAPRemove2
(a)(b)1BACB30MR4K71BOLTRemove3
-1115W1672-8RETAINER CAPRemove4
-1BACN10JC9CMNUTRemove5
-1115W1672-9RETAINER CAPRemove6
-1115W1671-3/-13PIN-LOWER, AFTRemove7
---LOWER STABILIZER
BRACE
Disconnect8
If not already re-
moved.
6-FASTENERSRemove9
(a)(b)
Keep the right MLG
Support Beam Low-
er Stabilizer Brace
AFT Fitting to use
for hole transfer into
the new fitting.
1-MLG SUPPORT BEAM
LOWER STABILIZER
BRACE AFT FITTING
Remove10
-1-SHIMRemove11
(c)--MLG SUPPORT BEAMClean12
(d)--MLG SUPPORT BEAMInspect13
Drill to Hole Diame-
ter 0.312 - 0.313
inch (e)(f)(g)
-115W1613U2FITTING AYDrill14
Break all sharp
edges on drilled
holes.
6-FASTENER HOLESDeburr15
-1115W1613U2FITTING AYPut / Hold16
(i)(j)1BACS40R033C040FSHIM-LAMINATEDPut / Hold
(h)-BMS 5-95SEALANTApply17
FIGURE 21: RIGHT MAIN LANDING GEAR - SUPPORT BEAM LOWER STABILIZER BRACE AFT FITTING
- REPLACEMENT
(SHEET 5 OF 7)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: June 02, 2025
777-57A0128 RB
118 of 144
REQUIREMENTS BULLETIN 777-57A0128
ALERTALERT

### Page 23

More DataQtyIdentificationNameTaskStep
-1115W1613U2FITTING AYInstall (New)18
(j)1BACS40R033C040FSHIM-LAMINATEDInstall (New)
(b)(k)(l)6BACB30US5K22BOLT, 12 PT HEADInstall (New)
Install under bolt
head.
6BACW10BP5CDCSK WASHERInstall (New)
Install under nut.6BACW10BP5DPWASHER-PLAINInstall (New)
Torque nut to 243 to
258 inch-lbs.
6BACN10HR5CDNUTInstall (New)
(m)
(n)6BACN10HR5CDNUTTorque19
-2AS15001-1PFITTING, LUBRICA-
TION
Install (New)20
---LOWER STABILIZER
BRACE
Connect21
-1115W1671-13PIN-LOWER, AFTInstall (New)22
-1115W1672-9RETAINER CAPInstall (New)23
Torque nut to 300 to
400 inch-lbs.
1BACN10JC9CMNUTInstall (New)24
-1115W1672-8RETAINER CAPInstall (New)25
(b)(l)(o)1BACB30MR4A71BOLTInstall (New)26
-1115W1672-10RETAINER CAPInstall (New)27
Torque nut to 82 to
88 inch-lbs.
1BACN11Z4CKNUTInstall (New)28
(p)-BMS 3-33GREASEApply29
(q)-115W1613U2FITTING AYIdentify30
(a) Make a note of the fastener orientation for installation.
(b) Refer to 777-200 SRM 51-40-02 as an accepted procedure.
(c) Use non-metallic tools to remove sealant from the upper and lower surfaces of the right MLG Support
Beam where the existing right MLG Support Beam Lower Stabilizer Brace AFT Fitting and shim were in-
stalled. Refer to SOPM 20-30-03 as an accepted procedure.
(d) Do an open hole High Frequency Eddy Current (HFEC) inspection of the MLG Support Beam for any
crack, in accordance with 777 NDT Manual Part 6, 51-00-02. If any crack is found, contact The Boeing
Company for repair instructions and do the repair.
(e) Use Special Tool MIT115W1613 to transfer hole locations from the existing right MLG Support Beam
Lower Stabilizer Brace AFT Fitting to new blank AFT Fitting in accordance with the MIT115W1613 tool
use instructions.
FIGURE 21: RIGHT MAIN LANDING GEAR - SUPPORT BEAM LOWER STABILIZER BRACE AFT FITTING
- REPLACEMENT
(SHEET 6 OF 7)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: June 02, 2025
777-57A0128 RB
119 of 144
REQUIREMENTS BULLETIN 777-57A0128
ALERTALERT

### Page 24

More DataQtyIdentificationNameTaskStep
(f) As an alternative to the MIT115W1613 tool use instructions, it is acceptable to use a mill machine to map
and transfer close ream hole locations from the existing right MLG Support Beam Lower Stabilizer Brace
AFT Fitting to new blank AFT Fitting. Refer to 777-200 SRM 51-40-05 as an accepted procedure.
(g) It is acceptable to oversize fastener holes, within the right MLG Support Beam Lower Stabilizer Brace
AFT Fitting and right MLG Support Beam, to 1st oversized close ream fastener holes if nominal close
ream fastener hole diameters can not be achieved. Additional oversize fasteners have been provided in
005W0183-9 kit. Refer to 777-200 SRM 51-40-05 as an accepted procedure.
(h) Apply faying surface seal using BMS 5-95 sealant on all mating surfaces. Refer to SOPM 20-50-19 as
an accepted procedure.
(i) Install shim between the upper flange of the right MLG Support Beam Lower Stabilizer Brace AFT Fitting
and the right MLG Support Beam. Remove 0.003 inch laminations as required to adjust thickness. Trim
profile of shim. Taper shim if required. Maintain edge condition. Refer to SOPM 20-50-20 as an accepted
procedure.
(j) Maximum pull-up after shim installation to be 0.005 inch.
(k) Install fasteners wet with BMS 5-95 sealant. Refer to SOPM 20-50-19 Method 2 as an accepted procedure.
(l) Install fasteners following the orientation noted during removal.
(m) Torque the nuts with a minimum of 60 minutes of squeeze-out life left in the fastener and fay surface
sealant. Refer to 777-200 SRM 51-40-02 as an accepted procedure.
(n) Re-apply torque to the nuts no sooner than:
- 10 minutes after the initial torque application, if Class B-1/2 or B-2 sealant was used.
- 10 minutes after the initial torque application, if Class C-20, C-24 or C-48 sealant was used.
- 60 minutes after the initial torque application, if sealant with a squeeze-out life longer than 48 hours was
used.
Make sure torque re-application is done before the squeeze-out life of the fastener and fay surface sealant
expires. Refer to 777-200 SRM 51-40-02 as an accepted procedure.
(o) Install fasteners wet with BMS 5-95 sealant. Refer to SOPM 20-50-19 as an accepted procedure.
(p) Lubricate the grease fittings with BMS 3-33 grease after installation of the right MLG Support Beam
Lower Stabilizer Brace AFT Fitting. Refer to 777 AMM 12-21-11 as an accepted procedure.
(q) Apply the service bulletin number to the right MLG Support Beam Lower Stabilizer Brace AFT Fitting at
this area only. Refer to SOPM 20-50-10, Code M as an accepted procedure.
FIGURE 21: RIGHT MAIN LANDING GEAR - SUPPORT BEAM LOWER STABILIZER BRACE AFT FITTING
- REPLACEMENT
(SHEET 7 OF 7)
Export Controlled ECCN: 9E991
See page 1 for details
Original Issue: June 02, 2025
777-57A0128 RB
120 of 144
REQUIREMENTS BULLETIN 777-57A0128
ALERTALERT

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
