# Boeing Service Bulletin A3183: Revision 6, from page 49

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2014-0756; AD 2015-11-04 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Service Bulletin A3183](https://openairdocs.org/service-documents/boeing/a3183.md)
- Title as filed: U.S. DOT/FAA - Service Bulletin 707-00A3183-06
- Pages: 106
- PDF: https://openairdocs.org/files/sha256/b4/4f/b44fc7db2675659669f7dab444875abef80d93cad0a92162e6c609d9917027e9
- Page: https://openairdocs.org/service-documents/boeing/a3183/file/b44fc7db2675

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 49

3.    ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL INFORMATION
CAUTION: KEEP THE WORK AREA, WIRES AND ELECTRICAL BUNDLES CLEAN OF METAL
PARTICLES OR CONTAMINATION WHEN YOU USE TOOLS. UNWANTED MATERIAL,
METAL PARTICLES OR CONTAMINATION CAUGHT IN WIRE BUNDLES CAN CAUSE
DAMAGE TO THE BUNDLES. DAMAGED WIRE BUNDLES CAN CAUSE SPARKS OR
OTHER ELECTRICAL DAMAGE.
NOTE: 1. Unless shown differently, these dimensions and tolerances are used:
– Linear dimensions are in inches
– Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus
or minus 0.03 inch
– Torque limits to tighten nuts and bolts are in SRM Chapter 51
2. Manual titles are referred to by acronyms. Refer to Paragraph 1.J., References, for
definition of the acronyms.
3. Obey all of the warnings and cautions given in the specified manual sections.
4. Use the approved fastener and process material substitutions in accordance with
SRM Chapter 51.
5. If the length of any fastener specified in this service bulletin does not meet installation
standards given in SRM Chapter 51, then a fastener of the same specification, or
an approved substitute, with a length which meets the installation standards given
in SRM Chapter 51 may be used. In addition, washers may be installed for fastener
grip length in accordance with SRM Chapter 51.
6. A Detailed Inspection is defined as: An intensive examination of a specific item,
installation, or assembly to detect damage, failure, or irregularity. Available lighting
is normally supplemented with a direct source of good lighting at an intensity deemed
appropriate. Inspection aids such as mirrors, magnifying lenses, etc. may be
necessary. Surface cleaning and elaborate procedures may be required.
7. A General Visual Inspection is defined as: A visual examination of an interior or
exterior area, installation or assembly to detect obvious damage, failure or irregularity.
This level of inspection is made from within touching distance unless otherwise
specified. A mirror may be necessary to enhance visual access to all exposed surfaces
in the inspection area. This level of inspection is made under normally available
lighting conditions such as daylight, hangar lighting, flashlight or drop-light and may
require removal or opening of access panels or doors. Stands, ladders or platforms
may be required to gain proximity to the area being checked.
8. These work instructions refer to procedures included in other Boeing documents.
When the words "refer to" are used and the operator has an accepted alternative
procedure, the accepted alternative procedure can be used. When the words "in
accordance with" are included in the instruction, the procedure in the Boeing document
must be used.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 27, 1975
A3183Revision 6: February 07, 2014
49 of 106
BOEING SERVICE BULLETIN A3183
ALERTALERT

### Page 50

9. Boeing Service Letter 707-SL-51-029 Damage Reporting and Repair Plan/Design
Guidelines, is an acceptable procedure to request information from Boeing for
additional structural repair instructions. The Service Letter describes what information
must be provided to Boeing before a structural repair can be provided.
10. Refer to Appendix A for nacelle struts # 1, # 2, # 3 and # 4 existing parts accountability
data.
11. Refer to Appendix B for nacelle struts # 1 and # 4, drag fitting chamfer/radius data.
12. Refer to Appendix C for bushing dimensions for drag fittings attachment holes.
13. The instructions in Paragraph 3.B., Work Instructions and the figures can include
operation of tools or test equipment. Boeing Engineering Tool Drawings, the Illustrated
Tool and Equipment Manual, and the Special Tool and Ground Handling Drawing
Index contain data on versions of the tools or test equipment that you can use. It is
permitted to use replaced tools. It is not permitted to use superseded tools.
14. If it is necessary to remove more parts for access, you can remove those parts. If
you can get access without removing identified parts, it is not necessary to remove
all of the identified parts. Jacking and shoring limitations must be observed.
15. Where the work instructions include installation of a kept part, a new or serviceable
part with the same part number can be installed as an alternative to the kept part.
16. This service bulletin includes functional test procedures for the systems changed by
this service bulletin. More functional tests can possibly be necessary in accordance
with standard maintenance practices because of interruption to other airplane systems.
17. At locations where "Boeing service bulletin XXXX" is shown, the XXXX is the base
number for a 707 Boeing service bulletin. Where "(707-XXXX)" is mentioned in the
service bulletin, it is the same as Boeing service bulletin XXXX.
18. Some Boeing parts are supplied in a temporary configuration. Those parts are
identified with a 'U', 'W', or 'Y' in place of the '-' (dash) in the part number. It is
permitted to install parts identified with a 'U', 'W', or 'Y' as an alternative to the '-'
(dash) part number. Boeing Drawing 005W0900 contains more data.
B. WORK INSTRUCTIONS
1. PART 1 - Engine Number (#) 1, # 2, # 3 And # 4 Nacelle Strut Inspection
a. Do a side force inspection of the engine # 1, # 2, # 3 and # 4. Apply alternating side forces
by hand to each side of engine nose cowl to inspect for any unusual structural noises.
NOTE: If a fitting is not completely severed, fore and aft movement between a cracked lug
and forward drag fitting clevis or between cracked tang ends may not be apparent
during this inspection. However, any unusual structural noises during this inspection
can indicate the start of a break.
(1) If any broken midspar fitting or any unusual structural noises is found, do the Life-Limit
Program - Mid Interval Inspections in accordance with Part 4 or Part 5.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 27, 1975
A3183Revision 6: February 07, 2014
50 of 106
BOEING SERVICE BULLETIN A3183
ALERTALERT

### Page 51

b. Do a General Visual inspection of the engine # 1, # 2, # 3 and # 4 nacelle strut for signs of
droop below normal position. Look at the stripe if present for misalignment. In addition, do a
General Visual inspection of the fairing straps, access panels and fairings between strut and
wing for Flexure damage (buckles, wrinkles, cracks, elongated holes, loose or broken fasteners,
etc). Noticeable nacelle droop or flexure damage may indicate that one or both midspar fittings
are broken.
(1) If any buckles, wrinkles, cracks, elongated holes, loose or broken fasteners, flexure
damage to sheet metal or noticeable nacelle droop are found, do the Life-Limit Program
- Mid Interval Inspections in accordance with Part 4 or Part 5.
2. PART 2 - Engine # 2 and # 3 Nacelle Strut - Midspar Fitting - Life-Limit Program.
a. Remove the engine # 2 and # 3 from the airplane. Refer to 707 Aircraft Maintenance Manual
71-5-0 as an accepted procedure.
b. Remove the nacelle strut # 2 and # 3 from the airplane. Refer to 707 Aircraft Maintenance
Manual 54-01-0 as an accepted procedure.
c. Remove/keep the upper portion of the torque bulkhead. Refer to Boeing drawing number
65C13873, Sheet 1 and Sheet 2, zones 1 thru 8 for 707B/C and 720B turbofan airplanes, and
Zones 7 thru 13 for 707 and 720 turbojet airplanes.
CAUTION: MAKE SURE THE LUG BORE LOCATIONS OF THE OLD MIDSPAR FITTINGS
ARE ACCURATELY MAINTAINED ON THE INSTALLATION OF THE NEW MIDSPAR
FITTINGS. IF THE LUG BORE LOCATIONS ARE NOT ACCURATELY MAINTAINED
MISALIGNMENT OF THE NACELLE STRUT AND THE WING FORWARD DRAG
FITTINGS CAN OCCUR.
d. Remove the nacelle strut # 2 and # 3 inboard and outboard midspar fittings. Refer to Boeing
drawing number 65CI3873, Sheet 1 and Sheet 2, zones 1 thru 8 for 707B/C and 720B turbofan
airplanes, and Zones 7 thru 13 for 707 and 720 turbojet airplanes.
NOTE: New midspar fittings are supplied undrilled. As an option fabricate tooling as necessary
to maintain the lug bore locations of the old midspar fittings.
e. Do a detailed inspection and a surface High Frequency Eddy Current (HFEC) inspection of
the removed nacelle strut # 2 and nacelle strut # 3 inboard and outboard midspar fittings for
any crack in accordance with FIGURE 3.
(1) If any crack equal to or larger than 0.3 inch is found in the inboard or outboard midspar
fitting, do the Part 6 - Overwing Support Fitting - Inspection and accomplish the remaining
Part 2 inspections.
(2) If every crack found is less than 0.3 inch, or if no crack is found, in the inboard or outboard
midspar fitting, continue with the Part 2 inspections.
f. Do an open hole High Frequency Eddy Current (HFEC) inspections of the vacated holes on
the torque bulkhead and midspar chords of the nacelle strut for any crack in accordance with
FIGURE 4.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 27, 1975
A3183Revision 6: February 07, 2014
51 of 106
BOEING SERVICE BULLETIN A3183
ALERTALERT

### Page 52

(1) If any crack is found in a vacated torque bulkhead or midspar chord rivet hole, oversize
the 3/16 inch rivet hole to 0.218 - 0.233 inch diameter and do an open hole High Frequency
Eddy Current (HFEC) inspection for any crack in accordance with 707, 720 NDT Manual
Part 6, 51-00-00, Figure 16, using a 0.02 notch calibration.
(a) If no crack is found in the oversized rivet hole, oversize the crack free rivet hole to
0.263-0.265 inch diameter and install new inboard and outboard midspar fittings and
existing torque bulkhead with the applicable BACR15BB8D*C oversize fasteners as
necessary and in accordance with Boeing drawing number 65C13873, Sheet 1 and
Sheet 2, zones 1 thru 8 for 707B/C and 720B turbofan airplanes, and Zones 7 thru
13 for 707 and 720 turbojet airplanes.
NOTE: On installation of new midspar fitting use the optional lug bore tooling and
match drill with existing fastener holes in the midspar and torque bulkhead
installations. Make sure fastener Edge Distance (ED) is not less than 1D +
0.050 inch.
(b) If any crack is found in the oversized rivet hole, contact Boeing for repair instructions
and do the repair instructed by Boeing. Any repair must include replacement of the
inboard and outboard midspar fittings with new fittings.
(2) If any crack is found in a vacated torque bulkhead or midspar chord bolt hole, contact
Boeing for repair instructions and do the repair instructed by Boeing. Any repair must
include replacement of the inboard and outboard midspar fittings with new fittings.
(3) If no crack is found in a vacated torque bulkhead or midspar chord fastener hole, install
new inboard and outboard midspar fittings and the existing torque bulkhead in accordance
with Boeing drawing number 65C13873, Sheet 1 and Sheet 2, zones 1 thru 8 for 707B/C
and 720B turbofan airplanes, and Zones 7 thru 13 for 707 and 720 turbojet airplanes.
NOTE: On installation of new midspar fitting use the optional lug bore tooling and match
drill with existing fastener holes in the midspar and torque bulkhead installations.
Make sure fastener Edge Distance (ED) is not less than 1D + 0.050 inch.
g. Do an open hole High Frequency Eddy Current (HFEC) inspection of the drag fitting attachment
holes for any crack in accordance with FIGURE 5.
(1) If any crack is found in a drag fitting attachment hole contact Boeing for repair instructions
and do the repair instructed by Boeing.
(2) If no crack is found in the drag fitting attachment holes, install new operator supplied
bushings in accordance with FIGURE 5. Refer to APPENDIX C for bushing dimensions.
h. Make sure the corner radius or chamfer at the forward inside edges of the left and right wing
forward drag fitting will clear the larger shoulder radius of the mating surface of the new midspar
fitting. If the drag fitting will not clear the larger shoulder radius of the mating surface of the
new midspar fitting, chamfer the drag fittings in accordance with drawing 65C14192, Sheet
1.
(1) If required, re-identify all trimmed drag fittings to indicate incorporation of this service
bulletin. Apply stencil markings (service bulletin number) to a visible area of the drag
fitting. Refer to SOPM 20-50-10 as an accepted procedure. Make sure that trimmed
fittings are used for all subsequent fitting replacements.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 27, 1975
A3183Revision 6: February 07, 2014
52 of 106
BOEING SERVICE BULLETIN A3183
ALERTALERT

### Page 53

i. Do an open hole High Frequency Eddy Current (HFEC) inspection of the front spar support
attachment holes for any crack in accordance with FIGURE 5.
(1) If any crack is found in the front spar support attachment holes, install a new front spar
support in accordance with Boeing service bulletin 3366 (707-3366).
j. Do a surface High Frequency Eddy Current (HFEC) inspection of the front spar support for
any crack in accordance with FIGURE 5.
(1) If any crack is found in the front spar support, install a new front spar support in accordance
with Boeing service bulletin 3366 (707-3366).
k. Apply sealant to the midspar area in accordance with drawing 65CI3873, Sheet 1 and Sheet
2, zones1 thru 8 for 707B/C and 720B turbofan airplanes, and Zones 7 thru 13 for 707 and
720 turbojet airplanes.
l. Apply Corrosion Inhibiting Compound (CIC) BMS 3-23, TYPE II, CLASS 2 to the midspar
fitting areas. Refer to SOPM 20-43-03 as an accepted procedure.
NOTE: Each operator should evaluate his airplanes environment, the inhibitor used, and
the application schedule to ensure adequate corrosion protection. Although Boeing
has developed BMS 3-23 as a standard for organic corrosion inhibitors compound
and recommends its use, other water displacing corrosion preventive compounds
can be satisfactory, based on operator evaluation and experience.
m. Install the nacelle strut # 2 and # 3 to the airplane. Refer to 707 Aircraft Maintenance Manual
54-01-0 as an accepted procedure.
NOTE: On installation of nacelle strut to the airplane, make sure to install new lug shims (if
and as required) to reduce lug-to-clevis gap below 0.002 inch.
n. Install the engine # 2 and # 3 to the airplane. Refer to 707 Aircraft Maintenance Manual 71-5-0
as an accepted procedure.
o. Put the airplane back to a serviceable condition.
3. PART 3 - Engine # 1 and # 4 Nacelle Strut - Midspar Fitting - Life-Limit Program.
a. Remove the engine # 1 and # 4 from the airplane. Refer to 707 Aircraft Maintenance Manual
71-5-0 as an accepted procedure.
b. Remove the nacelle strut # 1 and # 4 from the airplane. Refer to 707 Aircraft Maintenance
Manual 54-01-0 as an accepted procedure.
c. Remove/keep the torque bulkhead. Refer to Boeing drawing number 65C13839 Sheet 1,
zones 1 thru 17 for 707-100B LONG BODY, -100B SHORT BODY, -300B, -300C and 720B
turbofan airplanes, and Zones 20 thru 32 for 707-200 and 300 turbojet airplanes.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 27, 1975
A3183Revision 6: February 07, 2014
53 of 106
BOEING SERVICE BULLETIN A3183
ALERTALERT

### Page 54

CAUTION: MAKE SURE THE LUG BORE LOCATIONS OF THE OLD MIDSPAR FITTINGS
ARE ACCURATELY MAINTAINED ON THE INSTALLATION OF THE NEW MIDSPAR
FITTINGS. IF THE LUG BORE LOCATIONS ARE NOT ACCURATELY MAINTAINED
MISALIGNMENT OF THE NACELLE STRUT AND THE WING FORWARD DRAG
FITTINGS CAN OCCUR.
d. Remove the nacelle strut # 1 and # 4 inboard and outboard midspar fittings. Refer to Boeing
drawing number 65C13839 Sheet 1, zones 1 thru 17 for 707-100B LONG BODY, -100B
SHORT BODY, -300B, -300C and 720B turbofan airplanes, and Zones 20 thru 32 for 707-200
and 300 turbojet airplanes.
NOTE: New midspar fittings are supplied undrilled. As an option fabricate tooling as necessary
to maintain the lug bore locations of the old midspar fittings.
e. Do a detailed inspection and a surface High Frequency Eddy Current (HFEC) inspection of
the removed nacelle strut # 1 and nacelle strut # 4 inboard and outboard midspar fittings for
any crack in accordance with FIGURE 6.
(1) If any crack equal to or larger than 0.3 inch is found in the inboard or outboard midspar
fitting, do the Part 6 - Overwing Support Fitting - Inspection and accomplish the remaining
Part 3 inspections.
(2) If every crack found is less than 0.3 inch, or if no crack is found, in the inboard or outboard
midspar fitting, continue with the Part 3 inspections.
f. Do an open hole High Frequency Eddy Current (HFEC) inspections of the vacated holes on
the torque bulkhead and midspar chords of the nacelle strut for any crack in accordance with
FIGURE 7.
(1) If any crack is found in a vacated torque bulkhead or midspar chord rivet hole, oversize
the 3/16 inch rivet hole to 0.218 - 0.233 inch diameter and do an open hole High Frequency
Eddy Current (HFEC) inspection for any crack in accordance with 707, 720 NDT Manual
Part 6, 51-00-00, Figure 16, using a 0.02 notch calibration.
(a) If no crack is found in the oversized rivet hole, oversize the crack free rivet hole to
0.263-0.265 inch diameter and install new inboard and outboard midspar fittings and
existing torque bulkhead with the applicable BACR15BB8D*C oversize fasteners as
necessary and in accordance with Boeing drawing number 65C13839 Sheet 1, zones
1 thru 17 for 707-100B LONG BODY, -100B SHORT BODY, -300B, -300C and 720B
turbofan airplanes, and Zones 20 thru 32 for 707-200 and 300 turbojet airplanes.
NOTE: On installation of new midspar fitting use the optional lug bore tooling and
match drill with existing fastener holes in the midspar and torque bulkhead
installations. Make sure fastener Edge Distance (ED) is not less than 1D +
0.050 inch.
(b) If any crack is found in the oversized rivet hole, contact Boeing for repair instructions
and do the repair instructed by Boeing. Any repair must include replacement of the
inboard and outboard midspar fittings with new fittings.
(2) If any crack is found in a vacated torque bulkhead or midspar chord bolt hole, contact
Boeing for repair instructions and do the repair instructed by Boeing. Any repair must
include replacement of the inboard and outboard midspar fittings with new fittings.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 27, 1975
A3183Revision 6: February 07, 2014
54 of 106
BOEING SERVICE BULLETIN A3183
ALERTALERT

### Page 55

(3) If no crack is found in a vacated torque bulkhead or midspar chord fastener hole, install
new inboard and outboard midspar fittings and the existing torque bulkhead in accordance
with Boeing drawing number 65C13839 Sheet 1, zones 1 thru 17 for 707-100B LONG
BODY, -100B SHORT BODY, -300B, -300C and 720B turbofan airplanes, and Zones 20
thru 32 for 707-200 and 300 turbojet airplanes.
NOTE: On installation of new midspar fitting use the optional lug bore tooling and match
drill with existing fastener holes in the midspar and torque bulkhead installations.
Make sure fastener Edge Distance (ED) is not less than 1D + 0.050 inch.
g. Do an open hole High Frequency Eddy Current (HFEC) inspection of the drag fitting attachment
holes for any crack in accordance with FIGURE 8.
(1) If any crack is found in a drag fitting attachment hole contact Boeing for repair instructions
and do the repair instructed by Boeing.
(2) If no crack is found in the drag fitting attachment holes, install new operator supplied
bushings in accordance with FIGURE 8. Refer to APPENDIX C for bushing dimensions.
h. Make sure the corner radius or chamfer at the forward inside edges of the left and right wing
forward drag fitting will clear the larger shoulder radius of the mating surface of the new midspar
fitting. If the drag fitting will not clear the larger shoulder radius of the mating surface of the
new midspar fitting, chamfer the drag fittings in accordance with APPENDIX B.
(1) If required, re-identify all trimmed drag fittings to indicate incorporation of this service
bulletin. Apply stencil markings (service bulletin number) to a visible area of the drag
fitting. Refer to SOPM 20-50-10 as an accepted procedure. Make sure that trimmed
fittings are used for all subsequent fitting replacements.
i. Do an open hole High Frequency Eddy Current (HFEC) inspection of the front spar support
attachment holes for any crack in accordance with FIGURE 8.
(1) If any crack is found in the front spar support attachment holes, install a new front spar
support in accordance with Boeing service bulletin 3366 (707-3366).
j. Do a surface High Frequency Eddy Current (HFEC) inspection of the front spar support for
any crack in accordance with FIGURE 8.
(1) If any crack is found in the front spar support, install a new front spar support in accordance
with Boeing service bulletin 3366 (707-3366).
k. Apply sealant to the midspar area in accordance with Boeing drawing number 65C13839
Sheet 1.
l. Apply Corrosion Inhibiting Compound (CIC) BMS 3-23, TYPE II, CLASS 2 to the midspar
fitting areas. Refer to SOPM 20-43-03 as an accepted procedure.
NOTE: Each operator should evaluate his airplanes environment, the inhibitor used, and
the application schedule to ensure adequate corrosion protection. Although Boeing
has developed BMS 3-23 as a standard for organic corrosion inhibitors compound
and recommends its use, other water displacing corrosion preventive compounds
can be satisfactory, based on operator evaluation and experience.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 27, 1975
A3183Revision 6: February 07, 2014
55 of 106
BOEING SERVICE BULLETIN A3183
ALERTALERT

### Page 56

m. Install the nacelle strut # 1 and # 4 to the airplane. Refer to 707 Aircraft Maintenance Manual
54-01-0 as an accepted procedure.
NOTE: On installation of nacelle strut to the airplane, make sure to install new lug shims (if
and as required) to reduce lug-to-clevis gap below 0.002 inch.
n. Install the engine # 1 and # 4 to the airplane. Refer to 707 Aircraft Maintenance Manual 71-5-0
as an accepted procedure.
o. Put the airplane back to a serviceable condition.
4. PART 4 - Engine # 2 And # 3 Nacelle Strut - Midspar Fitting - Life-Limit Program - Mid Interval
Inspection
a. Remove the engine # 2 and # 3 from the airplane. Refer to 707 Aircraft Maintenance Manual
71-5-0 as an accepted procedure.
b. Remove the nacelle strut # 2 and # 3 from the airplane. Refer to 707 Aircraft Maintenance
Manual 54-01-0 as an accepted procedure.
c. Do a detailed inspection and a surface High Frequency Eddy Current (HFEC) inspection of
nacelle strut # 2 and nacelle strut # 3 inboard and outboard midspar fittings for any crack in
accordance with FIGURE 9.
(1) If any crack is found in the inboard or outboard midspar fitting, do the steps that follow:
(a) Remove/keep the upper portion of the torque bulkhead in accordance with Boeing
drawing number 65CI3873, Sheet 1 and Sheet 2, zones 1 thru 8 for 707B/C and
720B turbofan airplanes, and Zones 7 thru 13 for 707 and 720 turbojet airplanes.
CAUTION: MAKE SURE THE LUG BORE LOCATIONS OF THE OLD MIDSPAR
FITTINGS ARE ACCURATELY MAINTAINED ON THE INSTALLATION
OF THE NEW MIDSPAR FITTINGS. IF THE LUG BORE LOCATIONS ARE
NOT ACCURATELY MAINTAINED MISALIGNMENT OF THE NACELLE
STRUT AND THE WING FORWARD DRAG FITTINGS CAN OCCUR.
(b) Remove the inboard and outboard midspar fittings in accordance with Boeing drawing
number 65CI3873, Sheet 1 and Sheet 2, zones 1 thru 8 for 707B/C and 720B turbofan
airplanes, and Zones 7 thru 13 for 707 and 720 turbojet airplanes.
NOTE: New midspar fittings are supplied undrilled. As an option fabricate tooling
as necessary to maintain the lug bore locations of the old midspar fittings.
(c) Do an open hole High Frequency Eddy Current (HFEC) inspections of the vacated
holes on the torque bulkhead and midspar chords of the nacelle strut for any crack
in accordance with FIGURE 4.
1) If any crack is found in a vacated torque bulkhead or midspar chord rivet hole,
oversize the 3/16 inch rivet hole to 0.218 - 0.233 inch diameter and do an open
hole High Frequency Eddy Current (HFEC) inspection for any crack in
accordance with 707, 720 NDT Manual Part 6, 51-00-00, Figure 16, using a
0.02 notch calibration.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 27, 1975
A3183Revision 6: February 07, 2014
56 of 106
BOEING SERVICE BULLETIN A3183
ALERTALERT

### Page 57

a) If no crack is found in the oversized rivet hole, oversize the crack free rivet
hole to 0.263-0.265 inch diameter and install new inboard and outboard
midspar fittings and existing torque bulkhead with the applicable
BACR15BB8D*C oversize fasteners as necessary and in accordance with
Boeing drawing number 65CI3873, Sheet 1 and Sheet 2, zones 1 thru 8
for 707B/C and 720B turbofan airplanes, and Zones 7 thru 13 for 707 and
720 turbojet airplanes.
NOTE: On installation of new midspar fitting use the optional lug bore
tooling and match drill with existing fastener holes in the midspar
and torque bulkhead installations. Make sure fastener Edge
Distance (ED) is not less than 1D + 0.050 inch.
b) If any crack is found in the oversized rivet hole, contact Boeing for repair
instructions and do the repair instructed by Boeing. Any repair must include
replacement of the inboard and outboard midspar fittings with new fittings.
2) If any crack is found in a vacated torque bulkhead or midspar chord bolt hole,
contact Boeing for repair instructions and do the repair instructed by Boeing.
Any repair must include replacement of the inboard and outboard midspar fittings
with new fittings.
3) If no crack is found in a vacated torque bulkhead or midspar chord fastener hole,
install new inboard and outboard midspar fittings and the existing torque bulkhead
in accordance with Boeing drawing number 65CI3873, Sheet 1 and Sheet 2,
zones 1 thru 8 for 707B/C and 720B turbofan airplanes, and Zones 7 thru 13
for 707 and 720 turbojet airplanes.
NOTE: On installation of new midspar fitting use the optional lug bore tooling
and match drill with existing fastener holes in the midspar and torque
bulkhead installations. Make sure fastener Edge Distance (ED) is not
less than 1D + 0.050 inch.
(2) If any crack equal to or larger than 0.3 inch is found in the inboard or outboard midspar
fitting, do the Part 6 - Overwing Support Fitting - Inspection and accomplish the remaining
Part 4 inspections.
(3) If every crack found is less than 0.3 inch, or if no crack is found, in the inboard or outboard
midspar fitting, continue with the Part 4 inspections.
d. Do an open hole High Frequency Eddy Current (HFEC) inspection of the drag fitting attachment
holes for any crack in accordance with FIGURE 5.
(1) If any crack is found in a drag fitting attachment hole contact Boeing for repair instructions
and do the repair instructed by Boeing.
(2) If no crack is found in the drag fitting attachment holes, install new operator supplied
bushings in accordance with FIGURE 5. Refer to APPENDIX C for bushing dimensions.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 27, 1975
A3183Revision 6: February 07, 2014
57 of 106
BOEING SERVICE BULLETIN A3183
ALERTALERT

### Page 58

e. Make sure the corner radius or chamfer at the forward inside edges of the left and right wing
forward drag fitting will clear the larger shoulder radius of the mating surface of the new midspar
fitting. If the drag fitting will not clear the larger shoulder radius of the mating surface of the
new midspar fitting, chamfer the drag fittings in accordance with drawing 65C14192, Sheet
1.
(1) If required, re-identify all trimmed drag fittings to indicate incorporation of this service
bulletin. Apply stencil markings (service bulletin number) to a visible area of the drag
fitting. Refer to SOPM 20-50-10 as an accepted procedure. Make sure that trimmed
fittings are used for all subsequent fitting replacements.
f. Do an open hole High Frequency Eddy Current (HFEC) inspection of the front spar support
attachment holes for any crack in accordance with FIGURE 5.
(1) If any crack is found in the front spar support attachment holes, install a new front spar
support in accordance with Boeing service bulletin 3366 (707-3366).
g. Do a surface High Frequency Eddy Current (HFEC) inspection of the front spar support in
accordance with FIGURE 5.
(1) If any crack is found in the front spar support, install a new front spar support in accordance
with Boeing service bulletin 3366 (707-3366).
h. Apply sealant to the midspar area in accordance with drawing 65CI3873, Sheet 1 and Sheet
2, zones1 thru 8 for 707B/C and 720B turbofan airplanes, and Zones 7 thru 13 for 707 and
720 turbojet airplanes.
i. Apply Corrosion Inhibiting Compound (CIC) BMS 3-23, TYPE II, CLASS 2 to the midspar
fitting areas. Refer to SOPM 20-43-03 as an accepted procedure.
NOTE: Each operator should evaluate his airplanes environment, the inhibitor used, and
the application schedule to ensure adequate corrosion protection. Although Boeing
has developed BMS 3-23 as a standard for organic corrosion inhibitors compound
and recommends its use, other water displacing corrosion preventive compounds
can be satisfactory, based on operator evaluation and experience.
j. Install the nacelle strut # 2 and # 3 to the airplane. Refer to 707 Aircraft Maintenance Manual
54-01-0 as an accepted procedure.
NOTE: On installation of nacelle strut to the airplane, make sure to install new lug shims (if
and as required) to reduce lug-to-clevis gap below 0.002 inch.
k. Install the engine # 2 and # 3 to the airplane. Refer to 707 Aircraft Maintenance Manual 71-5-0
as an accepted procedure.
l. Put the airplane back to a serviceable condition.
5. PART 5 - Engine # 1 And # 4 Nacelle Strut - Midspar Fitting - Life-Limit Program - Mid Interval
Inspection
a. Remove the engine # 1 and # 4 from the airplane. Refer to 707 Aircraft Maintenance Manual
71-5-0 as an accepted procedure.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 27, 1975
A3183Revision 6: February 07, 2014
58 of 106
BOEING SERVICE BULLETIN A3183
ALERTALERT

### Page 59

b. Remove the nacelle strut # 1 and # 4 from the airplane. Refer to 707 Aircraft Maintenance
Manual 54-01-0 as an accepted procedure.
c. Do a detailed inspection and a surface High Frequency Eddy Current (HFEC) inspection of
nacelle strut # 1 and nacelle strut # 4 inboard and outboard midspar fittings for any crack in
accordance with FIGURE 10.
(1) If any crack is found in the inboard or outboard midspar fitting, do the steps that follow:
(a) Remove/keep the torque bulkhead in accordance with Boeing drawing number
65C13839 Sheet 1, zones 1 thru 17 for 707-100B LONG BODY, -100B SHORT
BODY, -300B, -300C and 720B turbofan airplanes, and Zones 20 thru 32 for 707-200
and 300 turbojet airplanes.
CAUTION: MAKE SURE THE LUG BORE LOCATIONS OF THE OLD MIDSPAR
FITTINGS ARE ACCURATELY MAINTAINED ON THE INSTALLATION
OF THE NEW MIDSPAR FITTINGS. IF THE LUG BORE LOCATIONS ARE
NOT ACCURATELY MAINTAINED MISALIGNMENT OF THE NACELLE
STRUT AND THE WING FORWARD DRAG FITTINGS CAN OCCUR.
(b) Remove the inboard and outboard midspar fittings in accordance with Boeing drawing
number 65C13839 Sheet 1, zones 1 thru 17 for 707-100B LONG BODY, -100B
SHORT BODY, -300B, -300C and 720B turbofan airplanes, and Zones 20 thru 32
for 707-200 and 300 turbojet airplanes.
NOTE: New midspar fittings are supplied undrilled. As an option fabricate tooling
as necessary to maintain the lug bore locations of the old midspar fittings.
(c) Do an open hole High Frequency Eddy Current (HFEC) inspections of the vacated
holes on the torque bulkhead and midspar chords of the nacelle strut for any crack
in accordance with FIGURE 7.
1) If any crack is found in a vacated torque bulkhead or midspar chord rivet hole,
oversize the 3/16 inch rivet hole to 0.218 - 0.233 inch diameter and do an open
hole High Frequency Eddy Current (HFEC) inspection for any crack in
accordance with 707, 720 NDT Manual Part 6, 51-00-00, Figure 16, using a
0.02 notch calibration.
a) If no crack is found in the oversized rivet hole, oversize the crack free rivet
hole to 0.263-0.265 inch diameter and install new inboard and outboard
midspar fittings and existing torque bulkhead with the applicable
BACR15BB8D*C oversize fasteners as necessary and in accordance with
Boeing drawing number 65C13839 Sheet 1, zones 1 thru 17 for 707-100B
LONG BODY, -100B SHORT BODY, -300B, -300C and 720B turbofan
airplanes, and Zones 20 thru 32 for 707-200 and 300 turbojet airplanes.
NOTE: On installation of new midspar fitting use the optional lug bore
tooling and match drill with existing fastener holes in the midspar
and torque bulkhead installations. Make sure fastener Edge
Distance (ED) is not less than 1D + 0.050 inch.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 27, 1975
A3183Revision 6: February 07, 2014
59 of 106
BOEING SERVICE BULLETIN A3183
ALERTALERT

### Page 60

b) If any crack is found in the oversized rivet hole, contact Boeing for repair
instructions and do the repair instructed by Boeing. Any repair must include
replacement of the inboard and outboard midspar fittings with new fittings.
2) If any crack is found in a vacated torque bulkhead or midspar chord bolt hole,
contact Boeing for repair instructions and do the repair instructed by Boeing.
Any repair must include replacement of the inboard and outboard midspar fittings
with new fittings.
3) If no crack is found in a vacated torque bulkhead or midspar chord fastener hole,
install new inboard and outboard midspar fittings and the existing torque bulkhead
in accordance with Boeing drawing number 65C13839 Sheet 1, zones 1 thru
17 for 707-100B LONG BODY, -100B SHORT BODY, -300B, -300C and 720B
turbofan airplanes, and Zones 20 thru 32 for 707-200 and 300 turbojet airplanes.
NOTE: On installation of new midspar fitting use the optional lug bore tooling
and match drill with existing fastener holes in the midspar and torque
bulkhead installations. Make sure fastener Edge Distance (ED) is not
less than 1D + 0.050 inch.
(2) If any crack in the inboard or outboard midspar fitting is equal to or larger than 0.3 inch,
do the Part 6 - Overwing Support Fitting - Inspection and accomplish the remaining Part
5 inspections.
(3) If every crack found is less than 0.3 inch, or if no crack is found, in the inboard or outboard
midspar fitting, continue with the Part 5 inspections.
d. Do an open hole High Frequency Eddy Current (HFEC) inspection of the drag fitting attachment
holes in accordance with FIGURE 8.
(1) If any crack is found in a drag fitting attachment hole contact Boeing for repair instructions
and do the repair instructed by Boeing.
(2) If no crack is found in the drag fitting attachment holes, install new operator supplied
bushings in accordance with FIGURE 8. Refer to APPENDIX C for bushing dimensions.
e. Make sure the corner radius or chamfer at the forward inside edges of the left and right wing
forward drag fitting will clear the larger shoulder radius of the mating surface of the new midspar
fitting. If the drag fitting will not clear the larger shoulder radius of the mating surface of the
new midspar fitting, chamfer the drag fittings in accordance with APPENDIX B.
(1) If required, re-identify all trimmed drag fittings to indicate incorporation of this service
bulletin. Apply stencil markings (service bulletin number) to a visible area of the drag
fitting. Refer to SOPM 20-50-10 as an accepted procedure. Make sure that trimmed
fittings are used for all subsequent fitting replacements.
f. Do an open hole High Frequency Eddy Current (HFEC) inspection of the front spar support
attachment holes in accordance with FIGURE 8.
(1) If any crack is found in the front spar support attachment holes, install a new front spar
support in accordance with Boeing service bulletin 3366 (707-3366).
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 27, 1975
A3183Revision 6: February 07, 2014
60 of 106
BOEING SERVICE BULLETIN A3183
ALERTALERT

### Page 61

g. Do a surface High Frequency Eddy Current (HFEC) inspection of the front spar support in
accordance with FIGURE 8.
(1) If any crack is found in the front spar support, install a new front spar support in accordance
with Boeing service bulletin 3366 (707-3366).
h. Apply sealant to the midspar area in accordance with Boeing drawing number 65C13839
Sheet 1.
i. Apply Corrosion Inhibiting Compound (CIC) BMS 3-23, TYPE II, CLASS 2 to the midspar
fitting areas. Refer to SOPM 20-43-03 as an accepted procedure.
NOTE: Each operator should evaluate his airplanes environment, the inhibitor used, and
the application schedule to ensure adequate corrosion protection. Although Boeing
has developed BMS 3-23 as a standard for organic corrosion inhibitors compound
and recommends its use, other water displacing corrosion preventive compounds
can be satisfactory, based on operator evaluation and experience.
j. Install the nacelle strut # 1 and # 4 to the airplane. Refer to 707 Aircraft Maintenance Manual
54-01-0 as an accepted procedure.
NOTE: On installation of nacelle strut to the airplane, make sure to install new lug shims (if
and as required) to reduce lug-to-clevis gap below 0.002 inch.
k. Install the engine # 1 and # 4 to the airplane. Refer to 707 Aircraft Maintenance Manual 71-5-0
as an accepted procedure.
l. Put the airplane back to a serviceable condition.
6. Part 6 - Overwing Support Fitting - Inspection
a. Do an open hole High Frequency Eddy Current (HFEC) inspection in the two forward most
fastener holes common to the inboard side of the nacelle strut overwing support fitting and
the wing front spar upper chord for any crack in accordance with FIGURE 11.
(1) If no cracks are found, oversize the holes to remove fatigued metal and install oversize
fasteners in accordance with FIGURE 12.
(2) If any crack is found in the two forward most fastener holes common to the inboard side
of the nacelle strut overwing support fitting and the wing front spar upper chord, do an
open hole HFEC inspection for any crack in the two forward most fastener holes common
to the outboard side of the nacelle strut overwing support fitting and the wing front spar
upper chord in accordance with FIGURE 12.
(a) If no cracks are found, oversize the holes to remove fatigued metal and install oversize
fasteners in accordance with FIGURE 13.
(3) If any crack is found in any of the four fastener holes common to the nacelle strut overwing
support fitting and the wing front spar upper chord, contact Boeing for repair instructions
and do the repair instructed by Boeing or install a new overwing support fitting in
accordance with Boeing service bulletin 3173 (707-3173).
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 27, 1975
A3183Revision 6: February 07, 2014
61 of 106
BOEING SERVICE BULLETIN A3183
ALERTALERT

### Page 62 (OCR)

ALERT
Original Issue: June 27, 1975
Revision 6 February 07, 2014
BOEING SERVICE BULLETIN A3183
ALERT
THIS FIGURE IS DELETED.
FIGURE 1: THIS FIGURE IS DELETED
(SHEET 1 OF 1)
Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright © Unpublished  A3183
Work - See page 1 for details.  62 of 106

### Page 63 (OCR)

BOEING SERVICE BULLETIN A3183
ALERT  ALERT
THIS FIGURE IS DELETED.
FIGURE 2: THEET 1 081)S DELETED
Devial set an 27, 2014  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  63 01 185
Work - See page 1 for details.

### Page 64 (OCR)

BOEING SERVICE BULLETIN А3183
ALERT  ALERT
NACELLE
STRUT #4
NACELLE
STRUT #3
MIDSPAR FITTING
NACELLE  NACELLE
STRUT #2  STRUT #1
LUG CRACKS
(TYPICAL)
TANG CRACKS
(TYPICAL)
UPPER HORIZONTAL TANG
VERTICAL
NACELLE STRUT  TANG
#2 AND #3
(TYPICAL)
SEE  LOWER HORIZONTAL TANG
MIDSPAR FITTING  2119126
FWD •
(TYPICAL)
FIGURE 3: NACELLE STRUT # 2 AND # 3 MIDSPAR FITTING INSPECTION - LIFE LIMIT PROGRAM
(SHEET 1 OF 3)
Original Issue: June 27, 1975
Revision 6 February 07, 2014  Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright © Unpublished  A3183
Work - See page 1 for details.  64 of 106

### Page 65 (OCR)

BOEING SERVICE BULLETIN А3183
ALERT  ALERT
LUG
_ BUSHING
134
UPPER HORIZONTAL TANG
- VERTICAL TANG
LOWER HORIZONTAL TANG
MIDSPAR FITTING
(TYPICAL)
INSPECTION
AREA  2119130
FIGURE 3: NACELLE STRUT # 2 AND # 3 MIDSPAR FITTING INSPECTION - LIFE LIMIT PROGRAM
(SHEET 2 OF 3)
Original Issue: June 27, 1975
Revision 6 February 07, 2014  Export Controlled ECCN: 9E991 - BOEING  A3183
PROPRIETARY - Copyright ® Unpublished
Work - See page 1 for details.  65 of 106

### Page 66

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for each nacelle strut.
More DataQtyIdentificationNameTaskStep
(a) (b)--SealantRemove1
(c)--SealantRemove2
(d)2-Midspar FittingClean
(e)2-Midspar FittingInspect3
(f)2-Midspar FittingInspect4
(a) Remove sealant from the area around the bushing lug bores of the inboard and outboard midspar fittings.
Use tools made from plastic or hardwood material. Do not use metal tools.
(b) Bushing removal is not required.
(c) Remove all surface sealant from the areas covering the inboard and outboard midspar fitting. Refer to
SOPM 20-50-19 as an accepted procedure. Make sure all the surface areas of the midspar fitting are
clearly visible before inspection.
(d) Clean all areas of the inboard and outboard midspar fittings. Refer to 707 Maintenance Manual Subject
12-3-1 or SOPM 20-30-03 as an accepted procedure.
(e) Do a detailed inspection of the inboard and outboard midspar fittings for any crack.
(f) Do a surface High Frequency Eddy Current (HFEC) inspection of the inboard and outboard midspar fittings
for any crack in accordance with 707, 720 NDT Part 6, 51-00-00, Figure 13 or Figure 24.
FIGURE 3: NACELLE STRUT # 2 AND # 3 MIDSPAR FITTING INSPECTION - LIFE LIMIT PROGRAM
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 27, 1975
A3183Revision 6 February 07, 2014
66 of 106
BOEING SERVICE BULLETIN A3183
ALERTALERT

### Page 67 (OCR)

BOEING SERVICE BULLETIN А3183
ALERT  ALERT
NACELLE
STRUT #4
NACELLE
STRUT #3
NACELLE
NACELLE STRUT #1
STRUT #2
NACELLE STRUT
MIDSPAR
CHORD
MIDSPAR
FITTING
FWD
NACELLE STRUT #2
FWD  TORQUE BULKHEAD  AND #3 (TYPICAL)  2120049
FIGURE 4: NACELLE STRUT # 2 AND # 3 TORQUE BULKHEAD AND MIDSPAR CHORD INSPECTIONS
(SHEET 1 OF 3)
Original Issue: June 27, 1975
Revision 6 February 07, 2014  PROPRIETARY - Copyright ® Unpublished  Export Controlled ECCN: 9E991 - BOEING  A3183
Work - See page 1 for details.  67 of 106

### Page 68 (OCR)

BOEING SERVICE BULLETIN А3183
ALERT  ALERT
WEB
•  •
FWD
MIDSPAR  MIDSPAR
CHORD  - T  CHORD
INSPECTION  VIEW A-A
HOLES
TYPICAL
10
UP
TORQUE  +
BULKHEAD
INSPECTION  VIEW B-B  0900212
HOLES  TYPICAL
FIGURE 4: NACELLE STRUT # 2 AND # 3 TORQUE BULKHEAD AND MIDSPAR CHORD INSPECTIONS
(SHEET 2 OF 3)
Original Issue: June 27, 1975
Revision 6 February 07, 2014  Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright © Unpublished  A3183
Work - See page 1 for details.  68 of 106

### Page 69

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for each nacelle strut.
More DataQtyIdentificationNameTaskStep
(a)--Midspar ChordInspect1
(b)--Torque BulkheadInspect2
(a) Do an open hole High Frequency Eddy Current (HFEC) inspection at all opened holes in the midspar
chords for any crack in accordance with 707, 720 NDT Part 6, 51-00-00, Figure 16, using a 0.03 notch
calibration.
(b) Do an open hole High Frequency Eddy Current (HFEC) inspection at all opened holes in the torque
bulkhead for any crack in accordance with 707, 720 NDT Part 6, 51-00-00, Figure 16, using a 0.03 notch
calibration.
FIGURE 4: NACELLE STRUT # 2 AND # 3 TORQUE BULKHEAD AND MIDSPAR CHORD INSPECTIONS
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 27, 1975
A3183Revision 6 February 07, 2014
69 of 106
BOEING SERVICE BULLETIN A3183
ALERTALERT

### Page 70 (OCR)

BOEING SERVICE BULLETIN А3183
ALERT  ALERT
NACELLE
STRUT #4
NACELLE
STRUT #3
> SEE (A
NACELLE  NACELLE
STRUT #2  STRUT #1
WING FORWARD
DRAG FITTING
NACELLE STRUT #2
AND #3 (TYPICAL)  2119138
FIGURE 5: NACELLE STRUT # 2 AND # 3 DRAG FITTING AND FRONT SPAR SUPPORT INSPECTIONS
(SHEET 1 OF 5)
Original Issue: June 27, 1975
Revision 6 February 07, 2014  Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright © Unpublished  A3183
Work - See page 1 for details.  70 of 106

### Page 71 (OCR)

BOEING SERVICE BULLETIN A3183
ALERT  ALERT
LOWER SKIN
DOUBLER
BUSHING
•DRAG FITTING
FWD C
VIEW A-A
INBOARD DRAG FITTING
(TYPICAL)
FRONT SPAR SUPPORT
DOUBLER
BUSHING
-DRAG FITTING
FWD <
VIEW B-B
OUTBOARD DRAG FITTING  2119438
(TYPICAL)
FIGURE 5: NACELLE STRUT # 2 AND # 3 DRAG FITTING AND FRONT SPAR SUPPORT INSPECTIONS
(SHEET 2 OF 5)
Original Issue: June 27, 1975
Revision 6 February 07, 2014  Export Controlled ECCN: 9E991 - BOEING  A3183
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  71 of 106

### Page 72 (OCR)

BOEING SERVICE BULLETIN А3183
ALERT  ALERT
FSS
417
FRONT SPAR
FWD
INSPECTION  FRONT SPAR SUPPORT
AREA  (TYPICAL)
2119762
FIGURE 5: NACELLE STRUT # 2 AND # 3 DRAG FITTING AND FRONT SPAR SUPPORT INSPECTIONS
(SHEET 3 OF 5)
Original Issue: June 27, 1975
Revision 6 February 07, 2014  Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright © Unpublished  A3183
Work - See page 1 for details.  72 of 106

### Page 73

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for each nacelle strut.
More DataQtyIdentificationNameTaskStep
(a) (b)2-BushingRemove1
(b) (c)2-BushingMeasure
(d)2-Drag Fitting HoleClean
(e)2-Drag Fitting HoleInspect2
(f)2-FastenerRemove / Keep3
(e)2-Drag Fitting HoleInspect4
(g)2-Front Spar Support
Hole
Inspect5
(h)--Front Spar SupportInspect6
-2-FastenerInstall (Kept)7
(i)2-Drag Fitting HoleHone8
(j)2-Drag Fitting HoleMeasure
(k)-TYPE 2, CLASS AChemical Conversion
Coating
Apply9
(l)-BMS 5-95SealantApply10
(b) (m)2-BushingInstall (New)
(n)2-BushingReam
(a) Remove bushing from the drag fitting attachment hole. Refer to SOPM 20-50-03 as an accepted procedure.
(b) Bushings are operator supplied parts. Refer to APPENDIX C to fabricate bushings.
(c) Measure the Internal Diameter (ID), Outer Diameter (OD), and flange thickness to determine the appro-
priate replacement bushing.
(d) Clean drag fitting hole. Refer to 707 Maintenance Manual Subject 12-3-1 or SOPM 20-30-03 as an ac-
cepted procedure.
(e) Do an open hole High Frequency Eddy Current (HFEC) inspection of the drag fitting attachment hole for
any crack in accordance with 707, 720 NDT Part 6, 51-00-00, Figure 16.
(f) Remove the fasteners common to the drag fitting and front spar support.
(g) Do an open hole High Frequency Eddy Current (HFEC) inspection of the front spar support attachment
holes for any crack in accordance with 707, 720 NDT Part 6, 51-00-00, Figure 16.
(h) Do a surface High Frequency Eddy Current (HFEC) inspection of the front spar support for any crack in
accordance with 707, 720 NDT Part 6, 51-00-00, Figure 4 or Figure 23 or 707, 720 NDT Part 6, 57-40-
07, Figure 2.
(i) Lightly hone the drag fitting hole as required to restore the surface finish of 63 microinches AA.
FIGURE 5: NACELLE STRUT # 2 AND # 3 DRAG FITTING AND FRONT SPAR SUPPORT INSPECTIONS
(SHEET 4 OF 5)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 27, 1975
A3183Revision 6 February 07, 2014
73 of 106
BOEING SERVICE BULLETIN A3183
ALERTALERT

### Page 74

More DataQtyIdentificationNameTaskStep
(j) Measure the drag fitting hole to make sure the drag fitting hole is within tolerance. Refer to APPENDIX
C for drag fitting hole diameter dimensions. If the drag fitting hole is not within tolerance contact Boeing
for repair instructions and do the repair.
(k) Apply chemical conversion coating to the drag fitting hole. Refer to SOPM 20-43-03 as an accepted pro-
cedure.
(l) Apply sealant to all mating surfaces of the bushing and drag fitting hole. Refer to SOPM 20-50-19 as an
accepted procedure.
(m) Use the shrink fit procedure to install the bushing to the drag fitting attachment hole. Refer to SOPM 20-
50-03 as an accepted procedure.
(n) Ream bushing bore holes to final diameter in accordance with Boeing Engineering Drawing 65C13873.
FIGURE 5: NACELLE STRUT # 2 AND # 3 DRAG FITTING AND FRONT SPAR SUPPORT INSPECTIONS
(SHEET 5 OF 5)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 27, 1975
A3183Revision 6 February 07, 2014
74 of 106
BOEING SERVICE BULLETIN A3183
ALERTALERT

### Page 75 (OCR)

BOEING SERVICE BULLETIN А3183
ALERT  ALERT
NACELLE
NACELLE  STRUT #3
STRUT #4
NACELLE
STRUT #1
MIDSPAR FITTING
NACELLE
STRUT #2
LUG CRACKS
(TYPICAL)
TANG CRACKS
(TYPICAL)
UPPER HORIZONTAL TANG
• VERTICAL
TANG
NACELLE STRUT
#1 AND #4
(TYPICAL)  LOWER HORIZONTAL TANG
SEE
FWD •  MIDSPAR FITTING  (TYPICAL)  2119763
FIGURE 6: NACELLE STRUT # 1 AND # 4 MIDSPAR FITTING INSPECTION - LIFE LIMIT PROGRAM
(SHEET 1 OF 3)
Original Issue: June 27, 1975
Revision 6 February 07, 2014  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  A3183
Work - See page 1 for details.  75 of 106

### Page 76 (OCR)

BOEING SERVICE BULLETIN А3183
ALERT  ALERT
LUG
_BUSHING
(2Y3Y4
UPPER HORIZONTAL TANG
- VERTICAL TANG
LOWER HORIZONTAL TANG
MIDSPAR FITTING
(TYPICAL)
INSPECTION
AREA  2119765
FIGURE 6: NACELLE STRUT # 1 AND # 4 MIDSPAR FITTING INSPECTION - LIFE LIMIT PROGRAM
(SHEET 2 OF 3)
Original Issue: June 21, 19/5
Revision 6 February 07, 2014  Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright © Unpublished  A3183
Work - See page 1 for details.  76 of 106

### Page 77

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for each nacelle strut.
More DataQtyIdentificationNameTaskStep
(a) (b)--SealantRemove1
(c)--SealantRemove2
(d)2-Midspar FittingClean
(e)2-Midspar FittingInspect3
(f)2-Midspar FittingInspect4
(a) Remove sealant from the area around the bushing lug bores of the inboard and outboard midspar fittings.
Use tools made from plastic or hardwood material. Do not use metal tools.
(b) Bushing removal is not required.
(c) Remove all surface sealant from the areas covering the inboard and outboard midspar fitting. Refer to
SOPM 20-50-19 as an accepted procedure. Make sure all the surface areas of the midspar fitting are
clearly visible before inspection.
(d) Clean all areas of the inboard and outboard midspar fittings. Refer to 707 Maintenance Manual Subject
12-3-1 or SOPM 20-30-03 as an accepted procedure.
(e) Do a detailed inspection of the inboard and outboard midspar fittings for any crack.
(f) Do a surface High Frequency Eddy Current (HFEC) inspection of the inboard and outboard midspar fittings
for any crack in accordance with 707, 720 NDT Part 6, 51-00-00, Figure 13 or Figure 24.
FIGURE 6: NACELLE STRUT # 1 AND # 4 MIDSPAR FITTING INSPECTION - LIFE LIMIT PROGRAM
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 27, 1975
A3183Revision 6 February 07, 2014
77 of 106
BOEING SERVICE BULLETIN A3183
ALERTALERT

### Page 78 (OCR)

BOEING SERVICE BULLETIN А3183
ALERT  ALERT
NACELLE
NACELLE  STRUT #3
STRUT #4
NACELLE
STRUT #1
NACELLE
STRUT #2
NACELLE STRUT
MIDSPAR
CHORD
B
MIDSPAR
FITTING
FWD <
FWD <  TORQUE BULKHEAD  NACELLE STRUT #1  AND #4 (TYPICAL)  2120051
FIGURE 7: NACELLE STRUT # 1 AND # 4 TORQUE BULKHEAD AND MIDSPAR CHORD INSPECTIONS
(SHEET 1 OF 3)
Original Issue: June 27, 1975
Revision 6 February 07, 2014  Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright © Unpublished  A3183
Work - See page 1 for details.  78 of 106

### Page 79 (OCR)

BOEING SERVICE BULLETIN А3183
ALERT  ALERT
WEB
MIDSPAR  - MIDSPAR
CHORD  CHORD
- INSPECTION  VIEW A-A
HOLES
TYPICAL
TORQUE-
BULKHEAD
••••  • 0
SUP
- INSPECTION
HOLES
VIEW B-B  2120052
TYPICAL
FIGURE 7: NACELLE STRUT # 1 AND # 4 TORQUE BULKHEAD AND MIDSPAR CHORD INSPECTIONS
(SHEET 2 OF 3)
Original Issue: June 27, 1975
Revision 6 February 07, 2014  Export Controlled ECCN: 9E991 - BOEING  A3183
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  79 of 106

### Page 80

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for each nacelle strut.
More DataQtyIdentificationNameTaskStep
(a)--Midspar ChordInspect1
(b)--Torque BulkheadInspect2
(a) Do an open hole High Frequency Eddy Current (HFEC) inspection at all opened holes in the midspar
chords for any crack in accordance with 707, 720 NDT Part 6, 51-00-00, Figure 16, using a 0.03 notch
calibration.
(b) Do an open hole High Frequency Eddy Current (HFEC) inspection at all opened holes in the torque
bulkhead for any crack in accordance with 707, 720 NDT Part 6, 51-00-00, Figure 16, using a 0.03 notch
calibration.
FIGURE 7: NACELLE STRUT # 1 AND # 4 TORQUE BULKHEAD AND MIDSPAR CHORD INSPECTIONS
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 27, 1975
A3183Revision 6 February 07, 2014
80 of 106
BOEING SERVICE BULLETIN A3183
ALERTALERT

### Page 81 (OCR)

BOEING SERVICE BULLETIN А3183
ALERT  ALERT
NACELLE
STRUT #4
SEE
NACELLE
STRUT #1
NACELLE
STRUT #2
NACELLE
STRUT #3
WING FORWARD
DRAG FITTING
NACELLE STRUT #1
AND #4 (TYPICAL)  2119768
FIGURE 8: NACELLE STRUT # 1 AND # 4 DRAG FITTING AND FRONT SPAR SUPPORT INSPECTIONS
(SHEET 1 OF 5)
Original Issue: June 27, 1975
Revision 6 February 07, 2014  Export Controlled ECCN: 9E991 - BOEING  A3183
PROPRIETARY - Copyright ® Unpublished
Work - See page 1 for details.  81 of 106

### Page 82 (OCR)

BOEING SERVICE BULLETIN A3183
ALERT  ALERT
SHIM
LOWER SKIN
DOUBLER
BUSHING -
DRAG FITTING
FWDS
VIEW A-A
1x2)8  X10  INBOARD DRAG FITTING
(TYPICAL)
FRONT SPAR SUPPORT
DOUBLER
3451
BUSHING -
DRAG FITTING
FWD C
VIEW B-B
OUTBOARD DRAG FITTING  2120047
(TYPICAL)
FIGURE 8: NACELLE STRUT # 1 AND # 4 DRAG FITTING AND FRONT SPAR SUPPORT INSPECTIONS
(SHEET 2 OF 5)
Original Issue: June 27, 1975
Revision 6 February 07, 2014  Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright © Unpublished  A3183
Work - See page 1 for details.  82 of 106

### Page 83 (OCR)

BOEING SERVICE BULLETIN А3183
ALERT  ALERT
FSS
704
FRONT SPAR
FWD
FRONT SPAR SUPPORT
(TYPICAL)
INSPECTION
AREA
2120048
FIGURE 8: NACELLE STRUT # 1 AND # 4 DRAG FITTING AND FRONT SPAR SUPPORT INSPECTIONS
(SHEET 3 OF 5)
Original Issue: June 27, 1975
Revision 6 February 07, 2014  Export Controlled ECCN: 9E991 - BOEING  A3183
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  83 of 106

### Page 84

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for each nacelle strut.
More DataQtyIdentificationNameTaskStep
(a) (b)2-BushingRemove1
(b) (c)2-BushingMeasure
(d)2-Drag Fitting HoleClean
(e)2-Drag Fitting HoleInspect2
(f)1-FastenerRemove3
(e)1-Drag Fitting HoleInspect4
(g)1-Front Spar Support
Hole
Inspect5
(h)--Front Spar SupportInspect6
-1-FastenerInstall (Kept)7
(i)2-Drag Fitting HoleHone8
(j)2-Drag Fitting HoleMeasure
(k)-TYPE 2, CLASS AChemical Conversion
Coating
Apply9
(l)-BMS 5-95SealantApply10
(b) (m)2-BushingInstall (New)
(n)2-BushingReam
(a) Remove bushing from the drag fitting attachment hole. Refer to SOPM 20-50-03 as an accepted procedure.
(b) Bushings are operator supplied parts. Refer to APPENDIX C to fabricate bushings.
(c) Measure the Internal Diameter (ID), Outer Diameter (OD), and flange thickness to determine the appro-
priate replacement bushing.
(d) Clean drag fitting hole. Refer to 707 Maintenance Manual Subject 12-3-1 or SOPM 20-30-03 as an ac-
cepted procedure.
(e) Do an open hole High Frequency Eddy Current (HFEC) inspection of the drag fitting attachment hole for
any crack in accordance with 707, 720 NDT Part 6, 51-00-00, Figure 16.
(f) Remove the fasteners common to the drag fitting and front spar support.
(g) Do an open hole High Frequency Eddy Current (HFEC) inspection of the front spar support attachment
holes for any crack in accordance with 707, 720 NDT Part 6, 51-00-00, Figure 16.
(h) Do a surface High Frequency Eddy Current (HFEC) inspection of the front spar support for any crack in
accordance with 707, 720 NDT Part 6, 51-00-00, Figure 4 or Figure 23 or 707, 720 NDT Part 6, 57-40-
07, Figure 2.
(i) Lightly hone the drag fitting hole as required to restore the surface finish of 63 microinches AA.
FIGURE 8: NACELLE STRUT # 1 AND # 4 DRAG FITTING AND FRONT SPAR SUPPORT INSPECTIONS
(SHEET 4 OF 5)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 27, 1975
A3183Revision 6 February 07, 2014
84 of 106
BOEING SERVICE BULLETIN A3183
ALERTALERT

### Page 85

More DataQtyIdentificationNameTaskStep
(j) Measure the drag fitting hole to make sure the drag fitting hole is within tolerance. Refer to APPENDIX
C for drag fitting hole diameter dimensions. If the drag fitting hole is not within tolerance contact Boeing
for repair instructions and do the repair.
(k) Apply chemical conversion coating to the drag fitting hole. Refer to SOPM 20-43-03 as an accepted pro-
cedure.
(l) Apply sealant to all mating surfaces of the bushing and drag fitting hole. Refer to SOPM 20-50-19 as an
accepted procedure.
(m) Use the shrink fit procedure to install the bushing to the drag fitting attachment hole. Refer to SOPM 20-
50-03 as an accepted procedure.
(n) Ream bushing bore holes to final diameter in accordance with Boeing Engineering Drawing 65C13839.
FIGURE 8: NACELLE STRUT # 1 AND # 4 DRAG FITTING AND FRONT SPAR SUPPORT INSPECTIONS
(SHEET 5 OF 5)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 27, 1975
A3183Revision 6 February 07, 2014
85 of 106
BOEING SERVICE BULLETIN A3183
ALERTALERT

### Page 86 (OCR)

BOEING SERVICE BULLETIN А3183
ALERT  ALERT
NACELLE
STRUT #4
NACELLE
STRUT #3
MIDSPAR FITTING
STRUT #2 NACELLE  NACELLE  STRUT #1
LUG CRACKS
(TYPICAL)
TANG CRACKS
(TYPICAL)
UPPER HORIZONTAL TANG
VERTICAL
TANG
NACELLE STRUT
#2 AND #3  SEE  LOWER HORIZONTAL TANG
(TYPICAL)
MIDSPAR FITTING
FWD •
NACELLE STRUT NOT
SHOWN FOR CLARITY
(TYPICAL)
FIGURE 9: NACELLE STRUT # 2 AND # 3 MIDSPAR FITTING INSPECTION - LIFE-LIMIT PROGRAM - MID
INTERVAL INSPECTION
(SHEET 1 OF 3)
Original Issue: June 27, 1975
Revision 6 February 07, 2014  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  A3183
Work - See page 1 for details.  86 of 106

### Page 87 (OCR)

BOEING SERVICE BULLETIN А3183
ALERT  ALERT
LUG
_ BUSHING
134
UPPER HORIZONTAL TANG
VERTICAL TANG
LOWER HORIZONTAL TANG
MIDSPAR FITTING
NACELLE STRUT NOT SHOWN
FOR CLARITY (TYPICAL)
INSPECTION
AREA  2253384
FIGURE 9: NACELLE STRUT # 2 AND # 3 MIDSPAR FITTING INSPECTION - LIFE-LIMIT PROGRAM - MID
INTERVAL INSPECTION
(SHEET 2 OF 3)
Original Issue: June 27, 1975
Revision 6 February 07, 2014  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  A3183
Work - See page 1 for details.  87 of 106

### Page 88

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for each nacelle strut.
More DataQtyIdentificationNameTaskStep
(a) (b)--SealantRemove1
(c)--SealantRemove2
(d)2-Midspar FittingClean
(e)2-Midspar FittingInspect3
(f)2-Midspar FittingInspect4
(a) Remove sealant from the area around the bushing lug bores of the inboard and outboard midspar fittings.
Use tools made from plastic or hardwood material. Do not use metal tools.
(b) Bushing removal is not required.
(c) Remove all surface sealant from the areas covering the inboard and outboard midspar fitting. Refer to
SOPM 20-50-19 as an accepted procedure. Make sure all the surface areas of the midspar fitting are
clearly visible before inspection.
(d) Clean all visible areas of the inboard and outboard midspar fittings. Refer to 707 Maintenance Manual
Subject 12-3-1 or SOPM 20-30-03 as an accepted procedure.
(e) Do a detailed inspection of all visible areas of the inboard and outboard midspar fittings for any crack.
(f) Do a surface High Frequency Eddy Current (HFEC) inspection of all visible areas of the inboard and
outboard midspar fittings for any crack in accordance with 707, 720 NDT Part 6, 51-00-00, Figure 13 or
Figure 24.
FIGURE 9: NACELLE STRUT # 2 AND # 3 MIDSPAR FITTING INSPECTION - LIFE-LIMIT PROGRAM - MID
INTERVAL INSPECTION
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 27, 1975
A3183Revision 6 February 07, 2014
88 of 106
BOEING SERVICE BULLETIN A3183
ALERTALERT

### Page 89 (OCR)

BOEING SERVICE BULLETIN А3183
ALERT  ALERT
NACELLE
NACELLE  STRUT #3
STRUT #4
NACELLE
STRUT #1
MIDSPAR FITTING
NACELLE
STRUT #2
LUG CRACKS
(TYPICAL)
TANG CRACKS
(TYPICAL)
UPPER HORIZONTAL TANG  VERTICAL
TANG
NACELLE STRUT
#1 AND #4  LOWER HORIZONTAL TANG
(TYPICAL)  SEE
FWD K  MIDSPAR FITTING
NACELLE STRUT NOT SHOWN
FOR CLARITY (TYPICAL)
FIGURE 10: NACELLE STRUT # 1 AND # 4 MIDSPAR FITTING INSPECTION - LIFE-LIMIT PROGRAM -
MID INTERVAL INSPECTION
(SHEET 1 OF 3)
Original Issue: June 27, 1975
Revision 6 February 07, 2014  Export Controlled ECCN: 9E991 - BOEING  A3183
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  89 of 106

### Page 90 (OCR)

BOEING SERVICE BULLETIN А3183
ALERT  ALERT
LUG
BUSHING
134
UPPER HORIZONTAL TANG
VERTICAL TANG
LOWER HORIZONTAL TANG
MIDSPAR FITTING
NACELLE STRUT NOT SHOWN
FOR CLARITY (TYPICAL)
INSPECTION
AREA  2253386
FIGURE 10: NACELLE STRUT # 1 AND # 4 MIDSPAR FITTING INSPECTION - LIFE-LIMIT PROGRAM -
MID INTERVAL INSPECTION
(SHEET 2 OF 3)
Original Issue: June 27, 1975
Revision 6 February 07, 2014  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  A3183
Work - See page 1 for details.  90 of 106

### Page 91

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for each nacelle strut.
More DataQtyIdentificationNameTaskStep
(a) (b)--SealantRemove1
(c)--SealantRemove2
(d)2-Midspar FittingClean
(e)2-Midspar FittingInspect3
(f)2-Midspar FittingInspect4
(a) Remove sealant from the area around the bushing lug bores of the inboard and outboard midspar fittings.
Use tools made from plastic or hardwood material. Do not use metal tools.
(b) Bushing removal is not required.
(c) Remove all surface sealant from the areas covering the inboard and outboard midspar fitting. Refer to
SOPM 20-50-19 as an accepted procedure. Make sure all the surface areas of the midspar fitting are
clearly visible before inspection.
(d) Clean all visible areas of the inboard and outboard midspar fittings. Refer to 707 Maintenance Manual
Subject 12-3-1 or SOPM 20-30-03 as an accepted procedure.
(e) Do a detailed inspection of all visible areas of the inboard and outboard midspar fittings for any crack.
(f) Do a surface High Frequency Eddy Current (HFEC) inspection of all visible areas of the inboard and
outboard midspar fittings for any crack in accordance with 707, 720 NDT Part 6, 51-00-00, Figure 13 or
Figure 24.
FIGURE 10: NACELLE STRUT # 1 AND # 4 MIDSPAR FITTING INSPECTION - LIFE-LIMIT PROGRAM -
MID INTERVAL INSPECTION
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 27, 1975
A3183Revision 6 February 07, 2014
91 of 106
BOEING SERVICE BULLETIN A3183
ALERTALERT

### Page 92 (OCR)

BOEING SERVICE BULLETIN А3183
ALERT  ALERT
SAILBOAT FAIRING
NACELLE  NACELLE
STRUT #4  STRUT #3
SEE DETAIL I
NACELLE
STRUT #2
→ D
NACELLE
STRUT #1
NACELLE STRUT
(TYPICAL)
OVERWING SUPPORT FITTING  WING FRONT SPAR UPPER CHORD
INBD
FWD<
DETAIL I
RIGHT WING OPPOSITE  LEFT WING SHOWN  2151835
(TYPICAL)
FIGURE 11: NACELLE STRUT # 1, # 2, # 3 AND # 4 INBOARD SIDE OVERWING SUPPORT FITTING
INSPECTION
(SHEET 1 OF 2)
Original Issue: June 27, 1975
Revision 6 February 07, 2014  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  A3183
Work - See page 1 for details.  92 of 106

### Page 93

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for each nacelle strut.
More DataQtyIdentificationNameTaskStep
(a)2-FastenerRemove1
(b)2-HoleInspect2
(a) Remove the two forward most fasteners attaching the inboard side of the nacelle strut overwing support
fitting to the wing front spar upper chord.
(b) Do an open hole High Frequency Eddy Current (HFEC) inspection of the holes in the chord, skin, and,
overwing support fitting for any crack in accordance with 707, 720 NDT Part 6, 51-00-00, Figure 16.
FIGURE 11: NACELLE STRUT # 1, # 2, # 3 AND # 4 INBOARD SIDE OVERWING SUPPORT FITTING
INSPECTION
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 27, 1975
A3183Revision 6 February 07, 2014
93 of 106
BOEING SERVICE BULLETIN A3183
ALERTALERT

### Page 94 (OCR)

BOEING SERVICE BULLETIN А3183
ALERT  ALERT
SAILBOAT FAIRING
NACELLE  NACELLE
STRUT #4  STRUT #3
SEE DETAIL I
NACELLE
STRUT #2
→ D
NACELLE
STRUT #1
NACELLE STRUT
(TYPICAL)
OVERWING SUPPORT FITTING  WING FRONT SPAR UPPER CHORD
INBD
FWD <
DETAIL
RIGHT WING OPPOSITE  LEFT WING SHOWN  2151853
(TYPICAL)
FIGURE 12: NACELLE STRUT # 1, # 2, # 3 AND # 4 OUTBOARD SIDE OVERWING SUPPORT FITTING
INSPECTION
(SHEET 1 OF 2)
Original Issue: June 27, 1975
Revision 6 February 07, 2014  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  A3183
Work - See page 1 for details.  94 of 106

### Page 95

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for each nacelle strut.
More DataQtyIdentificationNameTaskStep
(a)2-HoleDrill / Ream1
(b)2BACB30MB12-10BoltInstall (New)2
-2BACC30BH12CollarInstall (New)
(c)2-FastenerRemove3
(d)2-HoleInspect4
(a) Oversize the holes to 0.371 - 0.375 inch diameter to remove fatigued metal in accordance with 707-
100/200 SRM 51-2-5 or 707-300/400 SRM 51-2-5.
(b) Install the fasteners common to the inboard side of the nacelle strut overwing support fitting and the wing
front spar upper chord.
(c) Remove the two fasteners attaching the outboard side of the nacelle strut overwing support fitting to the
wing front spar upper chord.
(d) Do an open hole High Frequency Eddy Current (HFEC) inspection of the holes in the chord, skin, and,
overwing support fitting for any crack in accordance with 707, 720 NDT Part 6, 51-00-00, Figure 16.
FIGURE 12: NACELLE STRUT # 1, # 2, # 3 AND # 4 OUTBOARD SIDE OVERWING SUPPORT FITTING
INSPECTION
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 27, 1975
A3183Revision 6 February 07, 2014
95 of 106
BOEING SERVICE BULLETIN A3183
ALERTALERT

### Page 96 (OCR)

BOEING SERVICE BULLETIN А3183
ALERT  ALERT
SAILBOAT FAIRING
NACELLE  NACELLE
STRUT #4  STRUT #3
SEE DETAIL I
NACELLE
STRUT #2
→ D
NACELLE
STRUT #1
NACELLE STRUT
(TYPICAL)
OVERWING SUPPORT FITTING  WING FRONT SPAR UPPER CHORD
INBD
FWD <
DETAIL
RIGHT WING OPPOSITE  LEFT WING SHOWN  2173417
(TYPICAL)
FIGURE 13: NACELLE STRUT # 1, # 2, # 3 AND # 4 OUTBOARD SIDE OVERWING FASTENER
INSTALLATION
(SHEET 1 OF 2)
Original Issue: June 27, 1975
Revision 6 February 07, 2014  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  A3183
Work - See page 1 for details.  96 of 106

### Page 97

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for each nacelle strut.
More DataQtyIdentificationNameTaskStep
(a)2-HoleDrill / Ream1
(b)2BACB30MB12-10BoltInstall (New)2
-2BACC30BH12CollarInstall (New)
(a) Oversize the holes to 0.371 - 0.375 inch diameter to remove fatigued metal in accordance with 707-
100/200 SRM 51-2-5 or 707-300/400 SRM 51-2-5.
(b) Install the fasteners common to the outboard side of the overwing support fitting and the wing front spar
upper chord.
FIGURE 13: NACELLE STRUT # 1, # 2, # 3 AND # 4 OUTBOARD SIDE OVERWING FASTENER
INSTALLATION
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 27, 1975
A3183Revision 6 February 07, 2014
97 of 106
BOEING SERVICE BULLETIN A3183
ALERTALERT

### Page 98

The parts shown below are changed by this service bulletin. The Quantity is the number of parts changed on
each airplane. Components or sub-assembly parts are indented. The Quantity of the indented part is the number
of parts used on the next higher assembly.
RCPNCNew Part NumberQuantityNameRUCExisting Part Number
CR, S50-8227-1 thru -10, -13
thru -20, -23 thru -28, -31
, -32, -3001, -3002, -3007
thru -3010
1 eachStrut Assembly -
Equipped
RWK50-8227-1 thru -10, -13
thru -20, -23 thru -28, -31
, -32, -3001, -3002, -3007
thru -3010
CR, S65-2510-1, -2, -3001 thru
-3016, -3019 thru -3030,
-3033, -3034, -3037 thru
-3042, -3049 thru -3056,
-3059 thru -3110
1 eachStrut Assembly -
Equipped
RWK65-2510-1, -2, -3001 thru
-3016, -3019 thru -3030,
-3033, -3034, -3037 thru
-3042, -3049 thru -3056,
-3059 thru -3110
CR, S.5-85617-3000 thru -
3002, -3008, -3009, -
3011, -3014
1 eachStrut Assembly -
Structure
RWK.5-85617-3000 thru -
3002, -3008, -3009, -
3011, -3014
CR, S65-2516, -11 eachStrut Assembly -
Structure
RWK.65-2516, -1
CR, S65-2516-3000, -3026, -
3027, -3030
1 eachStrut Assembly -
Structure
RWK.65-2516-3000, -3026, -
3027, -3030
CS65-2536-15 or -251Midspar FittingDIS..5-85658-3001
CS65-2536-16 or -261Midspar FittingDIS..5-85658-3002
CS65-2536-15 or -251Midspar FittingDIS..5-85658-3017
CS65-2536-16 or -261Midspar FittingDIS..5-85658-3018
CS65-2536-15 or -251Midspar FittingDIS.. 65-2536-1
CS65-2536-16 or -261Midspar FittingDIS.. 65-2536-2
CS65-2536-15 or -251Midspar FittingDIS.. 65-2536-4
CS65-2536-16 or -261Midspar FittingDIS.. 65-2536-5
CS65-2536-19 or -271Midspar FittingDIS.. 65-2536-7
CS65-2536-20 or -281Midspar FittingDIS.. 65-2536-8
CS65-2536-15 or -251Midspar Fitting As-
sembly
DIS.. 65-2536-9
CS65-2536-16 or -261Midspar Fitting As-
sembly
DIS.. 65-2536-10
AS65-27303-321 eachBushing - Standard
Size
DIS... 65-27303-27, -28, -29
CS65-27303-321 eachBushing - Under-
size I.D.
DIS... 65-99744-427, -428, -
429
APPENDIX A: EXISTING PARTS ACCOUNTABILITY
(SHEET 1 OF 3)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 27, 1975
A3183Revision 6 February 07, 2014
98 of 106
BOEING SERVICE BULLETIN A3183
ALERTALERT

### Page 99

RCPNCNew Part NumberQuantityNameRUCExisting Part Number
CS66-1044-68Lug Shim - 0.001DIS66-1044
CS66-1044-74Lug Shim - 0.003DIS66-1044-1
CS66-1044-84Lug Shim - 0.006DIS66-1044-2
CS66-1044-94Lug Shim - 0.010DIS66-1044-3
CS66-1044-104Lug Shim - 0.016DIS66-1044-4
CS66-1044-114Lug Shim - 0.025DIS66-1044-5
RCPNCNew Part NumberQuantityNameRUCExisting Part Number
CR, S50-8228-1 thru -12, -15
thru -32, -3001, -3002, -
3007 thru -3014
1 eachStrut Assembly -
Equipped
RWK50-8228-1 thru -12, -15
thru -32, -3001, -3002, -
3007 thru -3014
CR, S65-2488-1, -2, -3001 thru
-3016, -3019 thru -3030,
-3033 thru -3042, -3049
thru 3128, -501, -502
1 eachStrut Assembly -
Equipped
RWK65-2488-1, -2, -3001 thru
-3016, -3019 thru -3030,
-3033 thru -3042, -3049
thru 3128, -501, -502
CR, S5-85627-3000, -3002, -
3003, -3009, -3010, -
3012, -3013, -3014, -
3015,
1 eachStrut Assembly -
Structure
RWK5-85627-3000, -3002, -
3003, -3009, -3010, -
3012, -3013, -3014, -
3015,
CR, S65-2494, -1, -30161 eachStrut Assembly -
Structure
RWK65-2494, -1, -3016
CR, S65-2494-3000, -3015, -
3019, -501
1 eachStrut Assembly -
Structure
RWK65-2494-3000, -3015, -
3019, -501
CS65-02534-211Midspar FittingDIS5-84467-3001
CS65-02534-221Midspar FittingDIS5-84467-3002
CS65-02534-211Midspar FittingDIS5-84467-3003
CS65-02534-221Midspar FittingDIS5-84467-3004
CS65-02534-211Midspar FittingDIS65-02534-1
CS65-02534-221Midspar FittingDIS65-02534-2
CS65-02534-211Midspar FittingDIS65-02534-4
CS65-02534-221Midspar FittingDIS65-02534-5
CS65-02534-191Midspar FittingDIS65-02534-7
CS65-02534-201Midspar FittingDIS65-02534-8
CS65-02534-211Midspar Fitting As-
sembly
DIS65-02534-9
APPENDIX A: EXISTING PARTS ACCOUNTABILITY
(SHEET 2 OF 3)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 27, 1975
A3183Revision 6 February 07, 2014
99 of 106
BOEING SERVICE BULLETIN A3183
ALERTALERT

### Page 100

RCPNCNew Part NumberQuantityNameRUCExisting Part Number
CS65-02534-221Midspar Fitting As-
sembly
DIS65-02534-10
AS65-27303-331 eachBushing - Standard
Size
DIS65-27303-26
CS66-1051-68Lug Shim - 0.001DIS66-1051
CS66-1051-74Lug Shim - 0.003DIS66-1051-1
CS66-1051-84Lug Shim - 0.006DIS66-1051-2
CS66-1051-94Lug Shim - 0.010DIS66-1051-3
CS66-1051-104Lug Shim - 0.016DIS66-1051-4
CS66-1051-114Lug Shim - 0.025DIS66-1051-5
Recommended Use CodeRUC
Discard the part.DIS
Make the change as specified in this service bulletin.RWK
Part Number CodePNC
This is the part number after the change.R
This is the new equivalent or replacement part number.S
Replacement CodeRC
Replacement not permitted. Do not replace a new part with an existing part.A
Replacement permitted. However, if the existing part is used, it will cancel the effect of the change
specified in this service bulletin
C
APPENDIX A: EXISTING PARTS ACCOUNTABILITY
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 27, 1975
A3183Revision 6 February 07, 2014
100 of 106
BOEING SERVICE BULLETIN A3183
ALERTALERT

### Page 101 (OCR)

BOEING SERVICE BULLETIN А3183
ALERT  ALERT
NAC STA
260.64  125 MACHINE FINISH IN REWORK AREAS
BREAK ALL SHARP EDGES 0.02  0.03
0.44
0.42
NAC WL  A  15.0°  0.32
143.25  -50-8733-1
50-8733-5
50-8733-7
50-8733-9
R1.96  1.98  0.42  (2 LOCATIONS)  VIEW A-A
0.40
(2 LOCATIONS)  DETAIL 1
NAC STA
260.64
15.0°
NAC WL  → 0.25
143.25  • 50-8733-11
50-8733-13
50-8733-15
50-8733-17
VIEW B-B
(2 LOCATIONS)
DETAIL 2
NAC STA
260.64
NAC WL  15.0°  - 0.20
143.25  50-8733-19
$ 1.64  1.66  RO.50 TRUE  (2 LOCATIONS)  VIEW C-C  2173705
(TYPICAL)
(2 LOCATIONS)  DETAIL 3
APPENDIX B: NACELLE STRUT # 1 AND # 4 - DRAG FITTING - CHAMFER / RADIUS INSPECTION
(SHEET 1 OF 2)
Original Issue: June 27, 1975
Revision 6 February 07, 2014  Export Controlled ECCN: 9E991 - BOEING  A3183
PROPRIETARY - Copyright ® Unpublished
Work - See page 1 for details.  101 of 106

### Page 102 (OCR)

BOEING SERVICE BULLETIN А3183
ALERT  ALERT
NAC STA
0.67  260.64  125 MACHINE FINISH IN REWORK AREAS
0.65  0.45  0.4/  BREAK ALL SHARP EDGES  0.03
0.36  0.02
0.34
NAC WL
-143.25  15.0°  0.38
50-8732-1
R 2.13  50-8732-5  50-8732-7
(2 LOCATIONS)  • 0.51  50-8732-9  VIEW D-D
0.49  (2 LOCATIONS)
RO.50 TRUE  DETAIL 4
(TYPICAL)
NAC STA
260.64
0.69  0.47
0.67  0.45
NAC WL
143.25  15.0°  0.16
-50-8732-11
50-8732-13
R 2.35  , 2.37  (2 LOCATIONS)  VIEW E-E
(2 LOCATIONS)  DETAIL 5
NAC STA
260.64
0.21
0.19
NAC WL
143.25  15.0°  - 0.25
-50-8732-15
R 1.39  1.41  RO.50 TRUE  (2 LOCATIONS)  VIEW F-F  2173706
(2 LOCATIONS)  (TYPICAL)  DETAIL 6
APPENDIX B: NACELLE STRUT # 1 AND # 4 - DRAG FITTING - CHAMFER / RADIUS INSPECTION
(SHEET 2 OF 2)
Original Issue: June 27, 1975
Revision 6 February 07, 2014  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  A3183
Work - See page 1 for details.  102 of 106

### Page 103 (OCR)

BOEING SERVICE BULLETIN A3183
ALERT  ALERT
CHAMFER BOTH ENDS
I.D. 0.005-0.015 X 45048°
O.D. 0.005-0.015 x 45048°  42° (EXCEPT AS NOTED)
O.D. 0.030-0.035 x 12°12°  11° FOR -1,-2,-3,-4,-13,
-14,-15,-16 ONLY
*A"DIA. (O.D.)
(SEE TABLE)
"B"DIA. (I.D.)  DIM "C"
(SEE TABLE)  (SEE TABLE)
125 / ALL SURFACES
BREAK ALL SHARP CORNERS.
ALL DIAMETERS TO BE CONCENTRIC WITHIN
0.003 TOLERANCE IN RADIUS (T.I.R).
Inboard Strut - Drag Fitting - Straight Bushing - Non Plated
Part Number  Drag Fitting Hole Diameter  B  C
69-2860-1  1.3125 - 1.3126  1.3145  1.3145  1.186  1.160  0.77  0.77
(a)  1.3165  1.189  0.78
69-2860-2  1.3125 - 1.3126  1.3145  1.3145  1.186  1.160  0.79  0.79
(a)  1.3165  1.189  0.80
(a)  This part is required with Top Kit 65C13873-2.
APPENDIX C: BUSHING DIMENSIONS FOR DRAG FITTING ATTACHMENT HOLES
(SHEET 1 OF 4)
Original Issue: June 27, 1975
Revision 6 February 07, 2014  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  A3183
Work - See page 1 for details.  103 of 106

### Page 104

Inboard Strut - Drag Fitting - Straight Bushing - Part Number - Plated (a)
CBA (After Plate)A (Before Plate)Drag Fitting Hole
Diameter
Part Number
0.79
0.80
0.791.192
1.221
1.2181.3461
1.3470
1.34611.3457
1.3462
1.34571.3445 - 1.344669-2860-50
(b)
0.92
0.93
0.921.192
1.221
1.2181.3461
1.3470
1.34611.3457
1.3462
1.34571.3445 - 1.344669-2860-51
(b)
0.97
0.98
0.971.192
1.221
1.2181.3461
1.3470
1.34611.3457
1.3462
1.34571.3445 - 1.344669-2860-59
(b)
(a) Cadmium plate in accordance with AMS-QQ-P-416, Type 1, Class 2. Plating optional on ID.
(b) This part is required with Top Kit 65C13873-1.
Outboard Strut - Drag Fitting - Straight Bushing - Non Plated
CBADrag Fitting Hole DiameterPart Number
0.80
0.81
0.801.090
1.127
1.1241.2520
1.2540
1.25201.2500 - 1.251069-2860-3
(a)
0.79
0.80
0.791.090
1.127
1.1241.2520
1.2540
1.25201.2500 - 1.251069-2860-4
(a)
(a) This part is required with Top Kit 65C13839-2.
Outboard Strut - Drag Fitting - Straight Bushing - Plated (a)
CBA (After Plate)A (Before Plate)Drag Fitting Hole
Diameter
Part Number
0.80
0.81
0.801.122
1.159
1.1561.2836
1.2845
1.28361.2832
1.2837
1.28321.2820 - 1.283069-2860-52
(b)
0.92
0.93
0.921.122
1.159
1.1561.2836
1.2845
1.28361.2832
1.2837
1.28321.2820 - 1.283069-2860-53
(b)
(a) Cadmium plate in accordance with AMS-QQ-P-416, Type 1, Class 2. Plating optional on ID.
(b) This part is required with Top Kit 65C13839-1.
APPENDIX C: BUSHING DIMENSIONS FOR DRAG FITTING ATTACHMENT HOLES
(SHEET 2 OF 4)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 27, 1975
A3183Revision 6 February 07, 2014
104 of 106
BOEING SERVICE BULLETIN A3183
ALERTALERT

### Page 105 (OCR)

BOEING SERVICE BULLETIN A3183
ALERT  ALERT
R. 030 MAX
CHAMFER  I.D. 0.005-0.015 × 45° 42°
48°
O.D. 0.005-0.015 × 45° 42°
Ø "D" O.D.
SEE TABLE
2.22
2.20 2.20
• "E" I.D.
"G"  SEE TABLE
SEE TABLE  • 0.0003
"F"
SEE TABLE
0.0005 A
125 / ALL SURFACES
BREAK ALL SHARP CORNERS 0.03:0.0089
Outboard Strut - Drag Fitting - Flanged Bushing - Plated (a)
Part Number  Drag Fitting  D (Before Plate)  D (After Plate)  E  F  G
Hole Diameter  +/-  +0.010
0.005  -0.000
69-42475-5  1.2820 - 1.2830  1.2832  1.2832  1.2836 1.2836  1.156  1.122  0.855  0.09
(b)  1.2837  1.2845  1.159
69-42475-6  1.2820 - 1.2830  1.2832  1.2832  1.2836  1.2836  1.156  1.122  0.935  0.09
(b)  1.2837  1.2845  1.159
69-42475-9  1.2820 - 1.2830  1.3457  1.3457  1.3461  1.3461  1.218  1.192  0.905  0.09
(c)  1.3462  1.3470  1.221
APPENDIX C: BUSHING DIMENSIONS FOR DRAG FITTING ATTACHMENT HOLES
(SHEET 3 OF 4)
Original Issue: June 27, 1975
Revision 6 February 07, 2014  Export Controlled ECCN: 9E991 - BOEING  A3183
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  105 of 106

### Page 106

Outboard Strut - Drag Fitting - Flanged Bushing - Plated (a)
G
+0.010
-0.000
F
+/-
0.005
ED (After Plate)D (Before Plate)Drag Fitting
Hole Diameter
Part Number
0.090.9061.192
1.221
1.2181.3461
1.3470
1.34611.3457
1.3462
1.34571.2820 - 1.283069-42475-10
(c)
0.090.8351.192
1.221
1.2181.3461
1.3470
1.34611.3457
1.3462
1.34571.2820 - 1.283069-42475-15
(c)
0.060.8551.122
1.159
1.1561.2836
1.2845
1.28361.2832
1.2837
1.28321.2820 - 1.283069-42475-18
(b)
(a) Cadmium plate in accordance with AMS-QQ-P-416, Type 1, Class 2. Plating optional on ID.
(b) This part is required with Top Kit 65C13839-1.
(c) This part is required with Top Kit 65C13873-1.
APPENDIX C: BUSHING DIMENSIONS FOR DRAG FITTING ATTACHMENT HOLES
(SHEET 4 OF 4)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 27, 1975
A3183Revision 6 February 07, 2014
106 of 106
BOEING SERVICE BULLETIN A3183
ALERTALERT

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
