# Boeing Service Bulletin A3364: SB-707-00A3364-04--, from page 37

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2018-0504; AD 2018-19-32 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Service Bulletin A3364](https://openairdocs.org/service-documents/boeing/a3364.md)
- Title as filed: SB-707-00A3364-04--
- Pages: 57
- PDF: https://openairdocs.org/files/sha256/ce/b8/ceb89d08ee66a3f79d5e209c1980d4fed872b639f5f5ab2e8499efdd2438a893
- Page: https://openairdocs.org/service-documents/boeing/a3364/file/ceb89d08ee66

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 37

Kit 65-92050 - Continued
NotesExisting Part
Number
Name65-92050-( )New Part Number
-12-11-10-9-8-7
QTY
--Rivet8-----BACR15BB6D9
--Rivet9-----BACR15BB6D16
Kit 65-92050 - Continued
NotesExisting Part
Number
Name65-92050-( )New Part Number
-18-17-16-15-14-13
QTY
--Bolt24----BACB30FM6-2
--Bolt66--3-BACB30FM6-5
--Bolt-8--8-BACB30FM6-6
--Bolt----4-BACB30FM8-5
--Bolt642432BACB30FM8-6
--Bolt----1-BACB30FM8-7
--Bolt10666-6BACB30FM8-8
--Bolt----6-BACB30FM8-9
--Bolt-6----BACB30FM8-12
--Bolt4-666-BACB30FM10-11
--Bolt-----6BACB30FM10-14
--Bolt-----2BACB30FM10-15
--Bolt414--4-BACB30FM14-10
--Bolt--10-10-BACB30FM14-11
--Bolt---106-BACB30FM14-12
--Bolt----8-BACB30FM14-13
--Bolt-----6BACB30FM16-15
--Bolt-----4BACB30FM16-18
--Bolt52----BACB30FN6-4
--Bolt8-88-4BACB30FN6-5
--Bolt----2-BACB30FN6-6
--Bolt-----6BACB30FN6-7
--Bolt84--7-BACB30MB6-8
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 29, 1979
A3364Revision 4: February 21, 2017
37 of 57
BOEING SERVICE BULLETIN A3364
ALERTALERT

### Page 38

Kit 65-92050 - Continued
NotesExisting Part
Number
Name65-92050-( )New Part Number
-18-17-16-15-14-13
QTY
--Bolt6355-5BACB30MB6-9
--Collar1020881310BACC30M6
--Collar516810148BACC30M8
--Collar14-6668BACC30M10
--Collar-14101028-BACC30M14
--Collar-----10BACC30M16
--Collar-75575BACC30X6
--Rivet716----BACR15BA6D6
--Rivet14-16161616BACR15BA6D7
--Rivet421--24-BACR15BB6D5
--Rivet5-1212-10BACR15BB6D6
--Rivet--141416-BACR15BB6D8
--Rivet-84--12BACR15BB6D9
--Rivet--559-BACR15BB6D14
--Rivet-----5BACR15BB6D17
--Rivet-----2BACR15CE6D6
--Rivet-----2BACR15CE6D9
Kit 65-92050 - Continued
NotesExisting Part
Number
Name65-92050-( )New Part Number
-24-23-22-21-20-19
QTY
--Washer-1----60-4849-9
--Washer1---1160-6961-4
--Washer--1---60-6961-6
--Bolt----1-65-23413-12
--Bolt1-----65-23413-13
--Bolt--1---65-23413-15
--Bolt-----165-23413-18
--Bolt-1----66-21024
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 29, 1979
A3364Revision 4: February 21, 2017
38 of 57
BOEING SERVICE BULLETIN A3364
ALERTALERT

### Page 39

Kit 65-92050 - Continued
NotesExisting Part
Number
Name65-92050-( )New Part Number
-24-23-22-21-20-19
QTY
--Washer---1--AN960PD1416
--Bolt---1--BACB30LJ14-69
--Nut-1---1BACN10JC12
--Nut1--11-BACN10JC14
--Nut--1---BACN10JC17
--Washer---1--BACW10BN14AC
Kit 65-92050 - Continued
NotesExisting Part
Number
Name65-92050-( )New Part Number
-30-29-28-27-26-25
QTY
--Washer-----160-6961-4
--Washer11-1--60-6961-6
--Bolt1-----65-23413-16
--Bolt-----165-23413-17
--Bolt---1--65-23413-20
--Bolt-1----65-23413-21
--Washer----1-AN960PD1216
--Washer--1---AN960PD1616
--Bolt----1-BACB30LJ12-70
--Bolt--1---BACB30LJ16-91
--Nut----11BACN10JC12
--Nut-111--BACN10JC16
--Nut1-----BACN10JC17
--Washer----1-BACW10BN12AC
--Washer--1---BACW10BN16AC
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 29, 1979
A3364Revision 4: February 21, 2017
39 of 57
BOEING SERVICE BULLETIN A3364
ALERTALERT

### Page 40

Kit 65-92050 - Continued
NotesExisting Part
Number
Name65-92050-(
)
New Part Number
-32-31
QTY
--Washer11AN960PD1416
--Bolt1-BACB30LJ14-89
--Bolt-1BACB30LJ14-92
--Nut11BACN10JC14
--Washer11BACW10BN14AC
2. Parts and Materials Supplied by the Operator
The following parts or materials are necessary to do the change in this service bulletin. Parts and
materials in the manuals given in Paragraph 1.J., References, can also be necessary. Examine
operator part and material supply to make sure all necessary parts and materials are available.
NotesNameQTYPart Number /
Specification
(a) (b)PRIMER8 ozBMS10-11, Type 1
(c) (d)CHEMICAL CONVERSION COAT-
ING
8 ozTYPE 2, CLASS A
(a) Refer to the Qualified Products List at the end of the Boeing Material Specification (BMS)
for supplier data.
(b) Some types of primer contain Strontium Chromate and will not be available in the European
Union (EU) after January 2019 without an authorization. EU operators are encouraged
to make sure their suppliers are authorized to provide this material after January 2019
and that users of this material comply with the risk mitigation measures and operational
conditions.
(c) Refer to SOPM 20-43-03 for material sources.
(d) Some types of Chemical Conversion Coating contain Chromium Trioxide Chromic Acid
and will not be available in the European Union (EU) after September 2017 without an
authorization. EU operators are encouraged to make sure their suppliers are authorized
to provide this material after September 2017 and that users of this material comply with
the risk mitigation measures and operational conditions.
3. Parts Modified and Reidentified
None.
4. Parts Removed and Not Replaced
None.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 29, 1979
A3364Revision 4: February 21, 2017
40 of 57
BOEING SERVICE BULLETIN A3364
ALERTALERT

### Page 41

D. Parts Necessary to Change Spares
None.
E. Special Tooling - Price and Availability
None.
F. Special Tooling Necessary to do this Service Bulletin
No special tools or equipment are necessary to do the change in this service bulletin. But, maintenance
and overhaul tools in the manuals given in Paragraph 1.J., References, can be necessary. Examine
operator tool supply to make sure all necessary tools are available.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 29, 1979
A3364Revision 4: February 21, 2017
41 of 57
BOEING SERVICE BULLETIN A3364
ALERTALERT

### Page 42

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 29, 1979
A3364Revision 4: February 21, 2017
42 of 57
BOEING SERVICE BULLETIN A3364
ALERTALERT
BLANK PAGE

### Page 43

3.    ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL INFORMATION
NOTE: KEEP THE WORK AREA, WIRES AND ELECTRICAL BUNDLES CLEAN OF METAL
PARTICLES OR CONTAMINATION WHEN YOU USE TOOLS. UNWANTED MATERIAL,
METAL PARTICLES OR CONTAMINATION CAUGHT IN WIRE BUNDLES CAN CAUSE
DAMAGE TO THE BUNDLES. DAMAGED WIRE BUNDLES CAN CAUSE SPARKS OR
OTHER ELECTRICAL DAMAGE.
1. Manual titles are referred to by acronyms. Refer to Paragraph 1.J., References, for
definition of the acronyms.
2. Obey all of the warnings and cautions given in the specified manual sections.
3. Unless shown differently, these dimensions and tolerances are used:
– Linear dimensions are in inches
– Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus
or minus 0.03 inch
– Tolerance on rivet and bolt edge margin is plus or minus 0.05 inch
– Angular tolerance is plus or minus 2 degrees
– Hole dimensions for standard solid rivets and fasteners are in Structural Repair
Manual (SRM) Chapter 51
– Torque Values:
— Values for structural fasteners are given in 707/720 Structural Repair
Manual, Chapter 51.
— Values for airframe maintenance tasks are included in Chapter 20 of 707/720
Aircraft Maintenance Manual (AMM).
— Non-standard torque values for maintenance tasks are included in the
applicable installation step.
4. Use the approved fastener, process and material substitutions in accordance with
SRM Chapter 51.
5. If the length of any fastener specified in this service bulletin does not meet installation
standards given in SRM Chapter 51, then a fastener of the same specification, or
an approved substitute, with a length which meets the installation standards given
in SRM Chapter 51 may be used. In addition, washers may be installed for fastener
grip length in accordance with SRM Chapter 51. Refer to SOPM 20-50-01 for alternate
full threaded fasteners (screws) needed for installation in this service bulletin.
6. A Detailed Inspection is defined as: An intensive examination of a specific item,
installation, or assembly to detect damage, failure, or irregularity. Available lighting
is normally supplemented with a direct source of good lighting at an intensity deemed
appropriate. Inspection aids such as mirrors, magnifying lenses, etc. may be
necessary. Surface cleaning and elaborate procedures may be required.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 29, 1979
A3364Revision 4: February 21, 2017
43 of 57
BOEING SERVICE BULLETIN A3364
ALERTALERT

### Page 44

7. These work instructions refer to procedures included in other Boeing documents.
When the words "refer to" are used and the operator has an accepted alternative
procedure, the accepted alternative procedure can be used. When the words "in
accordance with" are included in the instruction, the procedure in the Boeing document
must be used.
8. Boeing Service Letter 707-SL-51-029, Damage Reporting and Repair Plan/Design
Guidelines, is an acceptable procedure to request information from Boeing for
additional structural repair instructions. The Service Letter describes what information
must be provided to Boeing before a structural repair can be provided.
9. The instructions in Paragraph 3.B., Work Instructions and the figures can include
operation of tools or test equipment. Boeing Engineering Tool Drawings, the Illustrated
Tool and Equipment Manual, and the Special Tool and Ground Handling Drawing
Index contain data on versions of the tools or test equipment that you can use. It is
permitted to use replaced tools. It is not permitted to use superseded tools.
10. If it is necessary to remove more parts for access, you can remove those parts. If
you can get access without removing identified parts, it is not necessary to remove
all of the identified parts. Jacking and shoring limitations must be observed.
11. Where the work instructions include installation of a kept part, a new or serviceable
part with the same part number can be installed as an alternative to the kept part.
12. Use of colors in Figures is based on guidance from the ATA e-Business Program
(ATA) iSpec 2200.
13. The compliance times for the actions in Paragraph 3.B., WORK INSTRUCTIONS
are in Paragraph 1.E., Compliance.
B. WORK INSTRUCTIONS
1. Remove the inboard and outboard nacelle strut diagonal brace fairings. Refer to operator's standard
procedure to obtain access to the diagonal brace tubes, diagonal brace end fittings and mating
fittings.
2. Do a detailed inspection of all affected fittings and the diagonal brace tubes in accordance with
FIGURE 1.
3. If a High Frequency Eddy Current (HFEC) inspection of the diagonal brace tube or brace end
fittings and HFEC or alternative dye penetrant inspection of the mating fittings are scheduled,
support the weight of the airplane on jacks at wing and body Jack Points I, II, VI. Refer to 707/720
Structural Repair Manual Subject 51-6-1 as an accepted procedure.
4. With airplane stabilized on jacks, support the weight of the engine and strut to remove all load
from the brace coupling pins. If engine has been removed for any reason, support the weight of
the nacelle strut. Remove coupling pins and remove diagonal braces from mating fittings.
5. Do a HFEC inspection of the fittings (or alternative dye penetrant inspection of vertical webs on
aft mating fittings) and do a HFEC inspection of the diagonal brace tube in accordance withFIGURE
2.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 29, 1979
A3364Revision 4: February 21, 2017
44 of 57
BOEING SERVICE BULLETIN A3364
ALERTALERT

### Page 45

6. If bushing is removed on mating fittings for an open hole HFEC inspection, do the repair of the
fitting hole and bushing within the allowable limits in accordance with FIGURE 2.
7. If any crack is found, except for any crack in the lug holes of the forward or aft mating fitting within
repair limits, replace the cracked fitting or diagonal brace tube in accordance with FIGURE 3. If
any crack is found in the aft mating fitting on the lower surface of the wing, defuel and purge the
wing tank. Refer to 707/720 Maintenance Manual Chapter 28 as an accepted procedure. If any
crack is found in the forward mating fitting, remove engine. Refer to 707/720 Maintenance Manual
Subject 71-5-0 as an accepted procedure.
8. After replacement of an aft mating fitting, refuel the wing tank and check for fuel leaks at the fitting.
If any leak is found contact The Boeing Company for repair instructions and do the repair. After
replacement of a forward mating fitting, reinstall engine and check engine systems.
9. Upon completion of inspection, repair, modification or replacement, remove supports at engine or
strut, remove airplane jacks and reinstall fairings.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 29, 1979
A3364Revision 4: February 21, 2017
45 of 57
BOEING SERVICE BULLETIN A3364
ALERTALERT

### Page 46 (OCR)

BOEING SERVICE BULLETIN A3364
ALERT  ALERT
5)
INBOARD AND OUTBOARD NACELLE
STRUT DIAGONAL BRACE
TYPICAL EACH END
2538461
FIGURE 1: DETAILED INSPECTION OF FITTINGS AND DIAGONAL BRACE TUBE
(SHEET 1 OF 2)
Original Issue: June 29, 1979
Revision 4 February 21, 2017  Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  46 of 57

### Page 47

The step numbers shown below agree with the numbers shown in the circle symbols in the figure.
1. Do a detailed inspection for any crack in the exposed surface of the inboard and outboard nacelle strut
diagonal brace end fittings. Particular attention should be given to the surface of the fitting where it
enters the tube. Use of a bright light and mirror is suggested as an aid in inspecting the less accessible
areas of the fitting.
2. At both ends of the diagonal brace tube, do a detailed inspection for any crack around the fasteners
attached to the end fittings.
3. If any crack is found on the diagonal brace end fittings or the diagonal brace tube, support engine as
described in the general accomplishment instructions, remove coupling pins and attach fasteners and
replace cracked parts in accordance with FIGURE 3.
4. At the forward mating fitting on the nacelle strut, do a detailed inspection of the exposed portions of
the fitting lugs for any crack. Particular attention should be given to the central area of the aft edge of
the lugs.
5. If any crack is found in the edge of a lug, support engine and remove the coupling pin. Typical cracks
originate at the lug hole and propagate approximately horizontally to the edge of the lug. Replace such
cracked fittings in accordance with FIGURE 3. If a different type crack is found, contact The Boeing
Company for repair instructions and do the repair.
6. At the aft mating fitting on the wing lower surface, do a detailed inspection of the edge of the lug and
the forward and aft vertical webs of the fitting. Use of a bright light and mirror is suggested as an aid
in inspecting the less accessible area of the lug edge. Particular attention should also be given to the
forward web radius where the web meets the fitting lug and to the aft web where the web angle changes
or the web thickness changes.
7. If any crack is found, replace the cracked fitting in accordance with FIGURE 3.
FIGURE 1: DETAILED INSPECTION OF FITTINGS AND DIAGONAL BRACE TUBE
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 29, 1979
A3364Revision 4 February 21, 2017
47 of 57
BOEING SERVICE BULLETIN A3364
ALERTALERT

### Page 48 (OCR)

BOEING SERVICE BULLETIN A3364
ALERT  ALERT
INBOARD AND OUTBOARD NACELLE  TYPICAL EACH END
STRUT DIAGONAL BRACE
B-B  POSSIBLE CRACK  LOCATIONS
END FITTING
4 INNERMOST
END
END FITTING
OUTER SURFACE
TYPICAL EACH END  OUTER  BRACE TUBE
INNER  RADIUS  RADIUS  A-A  2538498
FIGURE 2: HIGH FREQUENCY EDDY CURRENT (HFEC) AND ALTERNATIVE DYE PENETRANTINSPECTION
OF DIAGONAL BRACE TUBE, FITTINGS AND MODIFICATION
(SHEET 1 OF 4)
Original Issue: June 29, 1979
Revision 4 February 21, 2017  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  A3364
Work - See page 1 for details.  48 of 57

### Page 49 (OCR)

BOEING SERVICE BULLETIN A3364
ALERT  ALERT
EMOT
16) AFT MATING FITTING  INBOARD NACELLE  (16) AFT MATING FITTING  OUTBOARD NACELLE
(13) 15)  13 15
2538474
FIGURE 2: HIGH FREQUENCY EDDY CURRENT (HFEC) AND ALTERNATIVE DYE PENETRANT INSPECTION
OF DIAGONAL BRACE TUBE, FITTINGS AND MODIFICATION
(SHEET 2 OF 4)
Original Issue: June 29, 1979
Revision 4 February 21, 2017  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  A3364
Work - See page 1 for details.  49 of 57

### Page 50

The step numbers shown below agree with the numbers shown in the circle symbols in the figure.
NOTE: Do surface HFEC inspection of flat and curved surfaces of fittings in accordance with 707/720
Nondestructive Test (NDT) Manual, Part 6, 51-00-00, Figures 4 or 23. Do open hole HFEC inspection
of holes in the fittings or brace tube, in accordance with 707/720 NDT Manual, Part 6, 51-00-00, Figures
11 or 16. For the interior inspection of the end fittings, use a shielded right angle pencil probe in
accordance with 707/720 NDT Manual Part 1, 51-06-00, Figure 1. Probe should be 7 to 8 inches long
with the angled portion 1 inch long. For dye penetrant inspection of vertical webs on aft mating fitting,
refer to SOPM 20-20-02 as an accepted procedure.
1. Do an interior surface HFEC inspection of the diagonal brace end fittings by inserting an angled HFEC
surface probe through the hole between the lugs of the end fitting.
2. Do a surface HFEC inspection of the inner surface of fitting for any crack at the intersection of the inner
radius and the inner surface, at the innermost end of the fitting, and around the heads of the fitting-to-tube
attach fasteners.
NOTE: Cracks in the fitting just inside the end of the tube typically occur in the inboard or outboard
side in line with the lug holes. Cracks in the innermost end of the fitting typically occur at the
intersections of the flat areas of the fitting interior.
3. Do an exterior surface HFEC inspection of the diagonal brace end fittings by removing the fitting-to-tube
attach fasteners and removing the fitting from tube.
4. Do a surface HFEC inspection around the fitting attach holes, the outer surface of the tubular portion
which nests just inside the end of the brace tube, when installed, and the inner end of the fitting. Pay
particular attention to the inboard and outboard areas of the outer surface at the tube end location and
to the thinner portions of the inner end of the fitting where the flat areas of the interior intersect.
5. With the fitting-to-tube attach fasteners removed, do an open hole HFEC inspection of the diagonal
brace tube for any crack.
6. If any crack is found in the diagonal brace tube, replace the diagonal brace tube.
7. If any crack is found in any end fitting, replace the fitting.
8. If an inboard or outboard diagonal brace end fitting attach fastener hole on a Group 3, 4, or 6 airplane
has already been oversized to 1/2 inch diameter to remove any crack, replace the brace assembly.
9. At the forward mating fitting in the nacelle strut without removing the bushings, do a surface HFEC
inspection for any crack in the edges of the lug holes. If no crack is found during the HFEC inspection
of the edges of the lug holes, then repeat HFEC inspections at intervals specified in Paragraph 1.E.,
Compliance. Another alternative for inspecting the edges of the lugs is to remove the lug hole bushings
and perform open hole HFEC inspection of the forward mating fitting lug holes. If open hole HFEC
inspection with bushings removed is done, oversize the hole (in accordance with Step 10), fabricate
and install a replacement bushing (in accordance with Step 12).
FIGURE 2: HIGH FREQUENCY EDDY CURRENT (HFEC) AND ALTERNATIVE DYE PENETRANT INSPECTION
OF DIAGONAL BRACE TUBE, FITTINGS AND MODIFICATION
(SHEET 3 OF 4)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 29, 1979
A3364Revision 4 February 21, 2017
50 of 57
BOEING SERVICE BULLETIN A3364
ALERTALERT

### Page 51

10. If any crack indication is noted, remove the bushing and do an open hole HFEC inspection of the lug
hole. If the crack can be removed by oversizing the hole by 1/16 inch diameter, oversize and reinspect
to confirm crack removal. Oversizing is based on the assumption that the lug hole has not been
previously oversized or the lug thickness reduced. If either has been done previously, replace the
forward mating fitting or contact The Boeing Company for repair instructions and do the repair.
11. If the crack has not been removed, replace the forward mating fitting or contact The Boeing Company
for repair instructions and do the repair.
12. Fabricate an aluminum-nickel-bronze bushing similar to the removed bushing, but with an outside
diameter 0.0001 to 0.0017 inch larger than the lug hole. Outer and inner diameters of new bushing
should be concentric within 0.01 inch T.I.R. Remove sharp edges of bushing and apply brush cadmium
plating to the outside diameter and ends of the bushing. Finished outside diameter of new bushing
should provide an interference fit of 0.0005 to 0.0025 inch in the lug hole. Coat inside of lug hole with
wet primer and shrink fit install bushing. Line ream new bushing hole to size.
13. At the aft mating fitting on the lower surface of the wing with the bushing in the lug hole, do a surface
HFEC inspection at the sides of the lug for any crack. Then remove the bushing from the lug hole and
do an open hole HFEC inspection for any crack. If no crack is found, oversize hole by 1/16 inch diameter
to remove any undetectable crack. If any crack is found, oversize the hole by 1/16 inch diameter, do
an open hole HFEC inspection to confirm removal and oversize an additional 1/16 inch diameter to
remove any undetectable crack. If the crack can not be removed, replace fitting or contact The Boeing
Company for repair instructions and do the repair.
NOTE: If the lug hole has already been oversized or the lug thickness reduced, during normal
maintenance rework, contact The Boeing Company for repair instructions and do the repair.
The original hole size should be 1.187 (inboard fitting 5-72319-) and 1.377 (outboard fitting
5-72316-) inch diameter. Original lug thickness should be 1.40 inches for inboard fittings
5-72319-3001, -3002, -3003, -3004, -3011, -3012, -3013, -3014, -3017, -3018, -3021, -3022,
-3029 and -3030, and 1.72 inches for fittings 5-72319-3007, -3008, -3015, -3016, -3025 and
-3026. Original lug thickness should be 1.50 inches for outboard fittings 5-72316-3007, -3008,
-3017, -3018, -3021, -3022, -3031 and -3032, and 1.68 inches for fittings 5-72316-3013, -3014,
-3019, -3020, -3023, -3024, -3029 and -3030.
14. Do a HFEC or alternative dye penetrant inspection of the vertical webs of the aft mating fittings for any
crack at the forward web radius where the web meets the fitting lug and at the aft web where the web
angle changes or the web thickness changes. If any crack is found, replace fitting.
15. Fabricate and install a new bushing in the aft mating fitting lug hole as in Step 12, except that the outer
and inner diameters should be concentric within 0.003 inch T.I.R. and the interference fit should be
0.0010 to 0.0024 inch in the lug hole. Ream bushing hole to size. Apply chemical conversion coating
and two coats of BMS10-11, Type 1, primer to fitting webs and lug surfaces and allow to dry one hour.
16. Repeat inspection of the aft mating fitting after modification of the aft mating fitting lug hole as specified
in Paragraph 1.E., Compliance. If the basic lug hole diameter was not oversized more than 1/16 inch
or the lug thickness reduced at any time, the modification may be repeated before the next repeat
inspection. If the lug hole was oversized by 1/8 inch diameter as a result of any crack, or the lug
thickness reduced, replace fitting.
FIGURE 2: HIGH FREQUENCY EDDY CURRENT (HFEC) AND ALTERNATIVE DYE PENETRANT INSPECTION
OF DIAGONAL BRACE TUBE, FITTINGS AND MODIFICATION
(SHEET 4 OF 4)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 29, 1979
A3364Revision 4 February 21, 2017
51 of 57
BOEING SERVICE BULLETIN A3364
ALERTALERT

### Page 52 (OCR)

BOEING SERVICE BULLETIN A3364
ALERT  ALERT
WING FRONT
NACELLE  SPAR
STRUT
DIAGONAL
BRACE  (2) DIMENSION Y
- FAIRING
91U AFT MATING
FITTING
2) DIMENSION 'X'
FWD
FORWARD MATING
FITTING
STRUT DIAGONAL BRACE
(TYPICAL FOR INBOARD AND OUTBOARD NACELLE, EXCEPT AS NOTED)
DIMENSION "X"
Airplane Group  Brace  Length (Inches)
All Airplane Groups  Outboard  51.65
Inboard  51.05
DIMENSION "Y"
Airplane Group  Brace  Length (Inches)
1, 5, 7  Outboard  2.63
3,4  Outboard  2.70
2, 6  Outboard  2.84
1, 3, 4, 5, 7  Inboard  2.41
2, 6  Inboard  2.51
FIGURE 3: FITTING AND DIAGONAL BRACE TUBE REPLACEMENT
(SHEET 1 OF 5)
Original Issue: June 29, 1979
Revision 4 February 21, 2017  Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright © Unpublished  Work - See page 1 for details.  52 of 57  A3364

### Page 53 (OCR)

BOEING SERVICE BULLETIN A3364
ALERT  ALERT
TORQUE NUT
800-1000 IN-LBS
A BRACE END
DIAGONAL BRACE 6)  FITTING
TUBE
BRACE END
FITTING
TORQUE NUT  600-700 IN-LBS  - B  - B  ) COUPLING  PIN BLOCK
•
DRAIN HOLE
A-A
UP
5) SEAL ASSEMBLY
B-B
APPLICABLE TO THE FOREMOST AND
AFTMOST ROW OF FASTENERS ON THE
OUTBOARD DIAGONAL BRACE ON
GROUP 1, 5, 7 AIRPLANES ONLY.
(VIEW LOOKING UP)
D-D
D
IF SEAL ASSEMBLY
C-C  2538706
FIGURE 3: FITTING AND DIAGONAL BRACE TUBE REPLACEMENT
(SHEET 2 OF 5)
Original Issue: June 29, 1979
Revision 4 February 21, 2017  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  A3364
Work - See page 1 for details.  53 of 57

### Page 54 (OCR)

BOEING SERVICE BULLETIN A3364
ALERT  ALERT
FASTENER NOTES
NOTE: SPOTFACING INSTRUCTIONS ARE APPLICABLE ONLY TO LATEST
DESIGN END FITTINGS
EARLIER DESIGN FITTINGS HAVE A FLAT INTERIOR SURFACE AT EACH
HOLE LOCATION.
• DRILL 0.437 (+0.005 OR -0.000) INCH DIAMETER HOLE. SPOTFACE INNER
END OF HOLE 0.875 (+0.020 OR -0.000) INCH DIAMETER WITH 0.03 - 0.06 INCH
RADIUS. SPOTFACE MINIMUM DEPTH (+0.02 OR -0.00 INCH) TO PROVIDE
FULL FLAT SURFACE FOR UNDERSIDE OF BOLT HEAD.
BOLT BACB30FM14-() (BACB30FM14A() OPTIONAL), COLLAR BACC30M14.
INSTALL THREE PLACES EACH FITTING. THESE THREE FASTENERS TO BE
IN END-TO-END ALIGNMENT.
• DRILL 0.375 (+0.004 OR -0.000) INCH DIAMETER HOLE. SPOTFACE INNER
END OF HOLE 0.750 (+0.020 OR -0.000) INCH DIAMETER WITH 0.03 - 0.06 INCH
RADIUS. SPOTFACE MINIMUM DEPTH (+0.02 OR -0.00 INCH) TO PROVIDE
FULL FLAT SURFACE FOR UNDERSIDE OF BOLT HEAD.
BOLT BACB30FM12-() (BACB30FM12A() OPTIONAL), COLLAR BACC30M12.
AT ALL END FITTING ATTACH FASTENER LOCATIONS NOT SPECIFIED PER
SECTION B-B, DRILL, SPOTFACE AND INSTALL FASTENERS PER SYMBOL O
• DRILL 0.218 (+0.011 OR -0.000) INCH DIAMETER HOLES IN NEW SEAL
ASSEMBLIES 69-71636-1 AND 69-71637-1 TO MATCH EXISTING HOLES IN
STRUCTURE. INSTALL BOLT BACB30LJ3-2 AND NUT BACN10JC3CM TWO
PLACES. SEAL BOLTS AND NUTS.  2541272
The step numbers shown below agree with the numbers shown in the circle symbols in the figure.
NOTE: 1.  When replacing any cracked fitting, the mating fitting or diagonal brace assembly is used to
locate the new fitting in place. Because of this, if more than one fitting is cracked at any one
nacelle strut, complete the replacement at each location before removing and discarding the
next cracked fitting. Also ensure that the supported position of the engine, or strut, does not
change in relation to the stabilized position of the wing.
2.  Revisions 1 and 2 of this service bulletin referred to Drawing 65C20477, supplied with Revision
1, for fitting replacement instructions. The instructions in this Figure 3 of the bulletin and on
the drawings supplied with this Revision 3 of the bulletin supersede and replace the instructions
in Drawing 65C20477. Fitting replacement that has already been accomplished in accordance
with Drawing 65C20477 is satisfactory provided limitations specified in Revision 3 or Revision
4 of the bulletin have not been exceeded.
Diagonal Brace End Fitting Replacement.
1.  If both end fittings have been removed from the brace tube for inspection, reinstall the fitting which is
not cracked. If both fittings are cracked, temporarily reinstall one of the cracked fittings. Retain coupling
pin blocks, if installed. If forward end fitting is being replaced on a Group 7 airplane, remove and discard
forward seal assembly.
FIGURE 3: FITTING AND DIAGONAL BRACE TUBE REPLACEMENT
(SHEET 3 OF 5)
Original Issue: June 29, 1979
Revision 4 February 21, 2017  Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright © Unpublished  A3364
Work - See page 1 for details.  54 of 57

### Page 55

2. Insert new fitting in tube and install coupling pins. Check distance between centerline of couplings and
between tube end and coupling centerlines. If the strut-to-wing relationship has been maintained,
distance between coupling centerlines will be as shown.
3. Drill new fitting to match holes in brace tube, spotface inner end of holes if latest design fitting is installed,
and install fitting attach fasteners. Install coupling pin and install pin block if previously installed.
4. If both end fittings were cracked, remove the second fitting from the tube and install new fitting as
previously described. Reinstall retained coupling pin, and pin block if previously installed.
5. If brace forward end fitting is replaced on a Group 7 airplane, install new seal assembly 69-71637-1
(outboard strut) or 69-71636-1 (inboard strut). On all affected airplanes, seal forward end of brace in
accordance with Drawing 65C20681.
Diagonal Brace Tube Replacement.
6. If the diagonal brace tube is replaced, the end fittings must also be replaced. Refer to AMM 54-1-41
as an accepted procedure for diagonal brace tube removal and replacement.
Forward Mating Fitting Replacement.
7. Remove and retain seal assembly. See Drawing 65C20681. On Group 1, 5 and 7 airplanes, replace
forward mating fitting in accordance with Drawing 65C20682. On Group 3 and 4 airplanes, replace in
accordance with Drawing 65C20683. On Group 2 and 6 airplanes, replace in accordance with Drawing
65C20684.
NOTE: 1. On each of the three drawings, installation of "pull" type lockbolts BACB30DX and
BACB30GW is indicated at several locations. At operator's option, BACB30MB and
BACB30FM hexagon drive bolts respectively may be used instead of the lockbolts.
2. At locations where the nacelle strut aft web requires cutting for fitting replacement,
operators may salvage the lower portion of the cut web or fabricate a new web portion,
0.05 inch thick, and splice plate, 0.06 inch thick, from 7075-T6 clad sheet
QQ-A-250/13. Apply chemical conversion coating and two coats of BMS10-11, Type
I primer to the parts. Alternatively, the 65C21734-( ) parts may be obtained from
Boeing.
8. Reinstall seal assembly in accordance with Drawing 65C20681 and restore sealant.
Aft Mating Fitting Replacement.
9. Before removing cracked fitting, mark outline of fitting on lower surface of wing lower skin with soft
marking pencil. Remove aft diagonal brace-to-fitting coupling pin and lower the aft brace clear of the
fitting. Remove fitting-to-wing attach fasteners and remove and discard cracked fitting. Salvage parts
specified on Drawings 65C21732 (inboard nacelle fitting) and 65C21733 (outboard nacelle fitting).
10. Attach new fitting to aft end of diagonal brace with coupling pin and position fitting against wing surface.
If nacelle strut-to-wing relationship has been maintained, new fitting will locate to marked outline of
removed fitting. Check for any gap between inboard and outboard side of fitting and wing surface. If
necessary, shim to remove gap.
FIGURE 3: FITTING AND DIAGONAL BRACE TUBE REPLACEMENT
(SHEET 4 OF 5)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 29, 1979
A3364Revision 4 February 21, 2017
55 of 57
BOEING SERVICE BULLETIN A3364
ALERTALERT

### Page 56

11. With fitting held firmly against wing lower surface, drill fitting to match existing holes in structure. Remove
fitting, deburr holes and complete installation of fitting in accordance with the applicable drawing.
FIGURE 3: FITTING AND DIAGONAL BRACE TUBE REPLACEMENT
(SHEET 5 OF 5)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 29, 1979
A3364Revision 4 February 21, 2017
56 of 57
BOEING SERVICE BULLETIN A3364
ALERTALERT

### Page 57 (OCR)

BOEING SERVICE BULLETIN A3364
ALERT  ALERT
Boeing Part Demand Intent
After review of this service bulletin (SB), Boeing asks that the primary engineer fill out this survey to
help Boeing predict the quantity and timing of the Boeing supplied kits.
Airline:
Contact Name:
Date:
Contact E-mail:
• Yes  • No Have/will you recommend to your airline to accomplish this SB?
• Yes  • No Would issuance of an Airworthiness Directive change this decision?
When would you likely be starting this SB incorporation? Month/ Year_
How many airplanes per month do you plan to accomplish? Airplane/Month
How many total airplanes do you plan to complete? Total Airplanes
For inspection related SBs, are you planning to replace on condition, or a fleet campaign to replace on
all airplanes regardless of condition?
- On Condition  Campaign
If you are not incorporating this SB at this time will you please help us understand the reason(s) why?
Your input will help us provide better customer support.
- Cost Prohibitive  Continue Inspections  _ Other
Operator Comments:
Within 45 days of the SB issue, or as soon after as possible, please scan this form and send to:
sbsolutions@boeing.com
Disclaimer: The data provided in this survey will be used for planning purposes only and does not
constitute a commitment on any part of the airlines to purchase the parts in question, nor does it constitute  2406498
a commitment on the part of Boeing to deliver the parts in question. This survey is a projection to help
Boeing forecast demand levels and timing to better support the customers schedule.
APPENDIX A: PART DEMAND INTENT
(SHEET 1 OF 1)
Original Issue: June 29, 1979
Revision 4 February 21, 2017  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  A3364
Work - See page 1 for details.  57 of 57

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
