# Boeing Service Bulletin A3537: No revision named, from page 25

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2012-0490; AD 2012-16-12 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Service Bulletin A3537](https://openairdocs.org/service-documents/boeing/a3537.md)
- Title as filed: U.S. DOT/FAA - Service Information
- Pages: 36
- PDF: https://openairdocs.org/files/sha256/3f/3b/3f3b9cbb6877889f33391a37c01a3d7ea7aa91dbbe24d518890ee6a04aae9480
- Page: https://openairdocs.org/service-documents/boeing/a3537/file/3f3b9cbb6877

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 25

The step numbers shown below agree with the numbers shown in the circle symbols in the figure.
More DataQtyIdentificationNameTaskStep
(a)8-Nacelle Strut and Aft
Fairing
Clean1
(b)-BMS 10-11 TYPE IPrimerApply2
(b)-BMS 10-11 TYPE IIEnamelApply
(a) Clean and mask an area to be painted on both sides of each nacelle strut and sailboat fairing. Refer to
SOPM 20-30-03 as an accepted procedure.
(b) On both sides of each nacelle, apply a stripe of paint across the nacelle strut and the sailboat fairing. Use
a color that contrasts with the color of the part on which the paint is applied. Refer to SOPM 20-41-02 as
an accepted procedure.
FIGURE 1: NACELLE STRUT AND SAILBOAT FAIRING DROOP STRIPE APPLICATION
(SHEET 2 OF 2)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: January 30, 2012
A3537
25 of 36
BOEING SERVICE BULLETIN A3537
ALERTALERT

### Page 26 (OCR)

BOEING SERVICE BULLETIN A3537
ALERT  ALERT
NACELLE
STRUT #4
NACELLE
STRUT #3
= D
NACELLE
STRUT #2
NACELLE
STRUT #1
NACELLE STRUT
SAILBOA®
-AIRING
ENGINE AND NACELLE
(TYPICAL)
- SKIN
JOINT
SKIN
JOINT  2112439
FIGURE 2: NACELLE STRUT DROOP
(SHEET 1 OF 2)
Original Issue: January 30, 2012
BOEING PROPRIETARY -  A3537
Copyright © Unpublished Work - See page 1 for details.  26 of 36

### Page 27

The step numbers shown below agree with the numbers shown in the circle symbols in the figure.
More DataQtyIdentificationNameTaskStep
Do a general visual
inspection (a) (b)
8-Nacelle Strut and Aft
Fairing
Inspect1
(a) Look at the nacelle strut to see if it has drooped below normal position. Look at the stripe if present for
misalignment. In addition, look at the fairing straps, access panels and fairings between strut and wing
for buckles, wrinkles, cracks, elongated holes and loose or broken fasteners. Noticeable nacelle droop
or flexure damage to sheet metal may indicate that one or both midspar fittings are broken.
(b) The recommended verification, prior to each flight, does not have to be accomplished by a qualified me-
chanic.
FIGURE 2: NACELLE STRUT DROOP
(SHEET 2 OF 2)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: January 30, 2012
A3537
27 of 36
BOEING SERVICE BULLETIN A3537
ALERTALERT

### Page 28 (OCR)

BOEING SERVICE BULLETIN А3537
ALERT  ALERT
NACELLE
STRUT #3
NACELLE
STRUT #2
MIDTING
2110707
FIGURE 3: ENGINE NUMBER 2 AND ENGINE NUMBER 3 NACELLE STRUT MIDSPAR FITTING INSPECTION
(SHEET 1 OF 3)
Original issue: January 30, 2012
BOEING PROPRIETARY -  A3537
Copyright © Unpublished Work - See page 1 for details.  28 of 36

### Page 29 (OCR)

BOEING SERVICE BULLETIN А3537
ALERT  ALERT
WEB
A-A
TYPICAL
0.38 R  1.00 R
NOMINAL  NOMINAL (3
(TYPICAL  (TYPICAL)
INCORRECT MIDSPAR FITTING  CORRECT MIDSPAR FITTING
FIGURE 3: ENGINE NUMBER 2 AND ENGINE NUMBER 3 NACELLE STRUT MIDSPAR FITTING INSPECTION
(SHEET 2 OF 3)
Original Issue: January 30, 2012
BOEING PROPRIETARY -  A3537
Copyright © Unpublished Work - See page 1 for details.  29 of 36

### Page 30

The step numbers shown below agree with the numbers shown in the circle symbols in the figure.
More DataQtyIdentificationNameTaskStep
---Fairing StrapsRemove / Keep1
---Midspar Joint Access
Panels
Remove / Keep
---Strut-to-Wing Leading
Edge Fairings
Remove / Keep2
(a)4-Midspar FittingInspect3
(a) Do a detailed inspection of the engine number 2 and engine number 3 nacelle strut inboard and outboard
midspar fittings to make sure the correct part is installed. The correct part can be identified by a 1 inch
nominal radius on the transition area between the fork and the lug.
FIGURE 3: ENGINE NUMBER 2 AND ENGINE NUMBER 3 NACELLE STRUT MIDSPAR FITTING INSPECTION
(SHEET 3 OF 3)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: January 30, 2012
A3537
30 of 36
BOEING SERVICE BULLETIN A3537
ALERTALERT

### Page 31 (OCR)

BOEING SERVICE BULLETIN А3537
ALERT  ALERT
NACELLE
STRUT #3
• D
NACELLE
STRUT #
SEE DETAIL II
NACELLE STRUT
#2 AND #3  SEE DETAIL I
2120246
FIGURE 4: ENGINE NUMBER 2 AND ENGINE NUMBER 3 NACELLE STRUT MIDSPAR FITTINGS HFEC
INSPECTION
(SHEET 1 OF 4)
Original Issue: January 30, 2012
A3537
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.  31 of 36

### Page 32 (OCR)

BOEING SERVICE BULLETIN A3537
ALERT  ALERT
1.50
, MIDSPAR FITTING
NACELLE STRUT SKIN
• ACCESS PANEL
FITTING HORIZONTAL TANGS  SEATING
0.375 R
• NACELLE STRUT SKIN
FITTING VERTICAL TANG
REMOVED MATERIAL
FWD
DETAIL I
OUTBOARD MIDSPAR FITTING
(ACCESS PANEL AND DRAG FITTING CLEVIS NOT SHOWN FOR CLARITY)
STRUT #2 SHOWN, STRUT #3 OPPOSITE
FAIRING ANGLE
0.375 R
NACELLE
ACCESS PANEL SEATING  STRUT SKIN
MIDSPAR FITTING  FITTING
1.50  HORIZONTAL TANGS
NACELLE STRUT SKIN  • FITTING VERTICAL TANG
FWD  REMOVED MATERIAL
DETAIL II
INBOARD MIDSPAR FITTING  2120416
(ACCESS PANEL AND DRAG FITTING CLEVIS NOT SHOWN FOR CLARITY)
STRUT #2 SHOWN, STRUT #3 OPPOSITE
FIGURE 4: ENGINE NUMBER 2 AND ENGINE NUMBER 3 NACELLE STRUT MIDSPAR FITTINGS HFEC
INSPECTION
(SHEET 2 OF 4)
Original Issue: January 30, 2012
Copyright © Unpublished Work - See page 1 for details.  BOEING PROPRIETARY -  32 of 36  A3537

### Page 33 (OCR)

BOEING SERVICE BULLETIN А3537
ALERT  ALERT
- SEAL INSTALLATION
AREA OF
EXPOSED EDGE
AROUND ALL 4-  FASTENER HEADS
INSIDE
RADIUS
FWD  (FULL WIDTH)
A-A
(TYPICAL)
TOP SURFACE
(FULL WIDTH)
AREA EXPOSED
AFTER SKIN CUTOUT
OUTER
RADIUS
(FULL WIDTH)
WING FITTING
CLEVIS
FWD
(TYPICAL)  B-B  2120271
The step numbers shown below agree with the numbers shown in the circle symbols in the figure.
FIGURE 4: ENGINE NUMBER 2 AND ENGINE NUMBER 3 NACELLE STRUT MIDSPAR FITTINGS HFEC
INSPECTION
(SHEET 3 OF 4)
Original Issue: January 30, 2012
A3537
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.  33 of 36

### Page 34

More DataQtyIdentificationNameTaskStep
Gain additional ac-
cess for inspection.
(b) (c) (d)
--Upper Portion of Ac-
cess Panel
Cut1
This step is not re-
quired if the panels
have already been
cut.
HFEC inspect both
the inboard & out-
board Midspar Fit-
tings. (a) (e) (f)
2-Midspar FittingInspect2
(g)-BMS 3-23 OR BMS 3-
35
Corrosion Inhibiting
Compound
Apply3
(a) Perform a HFEC inspection in the areas indicated. Refer to Manual 707, 720 NDT Part 6, 51-00-00 Figure
24 as an accepted procedure.
(b) At the outboard midspar fitting, remove upper portion of access panel seating as shown in Detail I. Make
forward edge of cutout flush with aft edge of strut skin. Finish raw edges as given in operator's standard
procedure.
(c) At the inboard midspar fitting, remove upper portion of access panel seating as shown in Detail II. Make
forward edge of cutout flush with aft edge of strut skin. Also remove portion of fairing angle level with top
of existing circular cutout above fitting lug hole as shown. Finish raw edges as given in operator's standard
procedure.
(d) If nutplate rivet edge margin interferes with cutout of seating area on access panel, replace the nutplate
with one that has a corner type rivet ear.
(e) The trimming of material as shown in Details I and II is required for this inspection.
(f) Clean the indicated areas of the Midspar Fitting as required for the HFEC inspection. Refer to 707 Main-
tenance Manual Subject 12-3-1 as an accepted procedure.
(g) If no cracks are found in the midspar fittings, spray exposed areas of fittings with organic corrosion inhibitor.
FIGURE 4: ENGINE NUMBER 2 AND ENGINE NUMBER 3 NACELLE STRUT MIDSPAR FITTINGS HFEC
INSPECTION
(SHEET 4 OF 4)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: January 30, 2012
A3537
34 of 36
BOEING SERVICE BULLETIN A3537
ALERTALERT

### Page 35 (OCR)

BOEING SERVICE BULLETIN А3537
ALERT  ALERT
NACELLE
STRUT #3
NACELLE
STRUT #2
2112445
FIGURE 5: ENGINE NUMBER 2 AND ENGINE NUMBER 3 NACELLE STRUT FAIRING AND PANEL
INSTALLATION
(SHEET 1 OF 2)
Original Issue: January 30, 2012
A3537
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.  35 of 36

### Page 36

The step numbers shown below agree with the numbers shown in the circle symbols in the figure.
More DataQtyIdentificationNameTaskStep
---Strut-to-Wing Leading
Edge Fairings
Install (Kept)1
---Midspar Joint Access
Panels
Install (Kept)2
---Fairing StrapsInstall (Kept)
FIGURE 5: ENGINE NUMBER 2 AND ENGINE NUMBER 3 NACELLE STRUT FAIRING AND PANEL
INSTALLATION
(SHEET 2 OF 2)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: January 30, 2012
A3537
36 of 36
BOEING SERVICE BULLETIN A3537
ALERTALERT

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
