# Boeing Service Bulletin A3539: No revision named, from page 37

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2014-0009; AD 2014-13-11 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Service Bulletin A3539](https://openairdocs.org/service-documents/boeing/a3539.md)
- Title as filed: U.S. DOT/FAA - Service Bulletin - 707-00A3539-00
- Pages: 110
- PDF: https://openairdocs.org/files/sha256/6a/0a/6a0ac8f59b887b835591433a550daf7922c5d99625fd0f99cdd5c4f57cb35267
- Page: https://openairdocs.org/service-documents/boeing/a3539/file/6a0ac8f59b88

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 37

Group 1:
Scribe Line Inspection
Elapsed HoursTask HoursNumber of PersonsTask
20.080.04Figure 1
6.012.02Figure 5
2.04.02Figure 9
28.0 *96.0 *TOTAL FOR EACH AIRPLANE
* Total Task Hours and Elapsed Hours dependent upon total number of fuselage
areas being inspected.
* Additional time is required for paint and sealant removal.
* More time will be required for additional inspections and repairs if scribe lines or
other damage is found.
* More time may be required for inspections around large repair doublers.
Group 2:
Scribe Line Inspection
Elapsed HoursTask HoursNumber of PersonsTask
20.080.04Figure 2
6.012.02Figure 6
2.04.02Figure 9
28.0 *96.0 *TOTAL FOR EACH AIRPLANE
* Total Task Hours and Elapsed Hours dependent upon total number of fuselage
areas being inspected.
* Additional time is required for paint and sealant removal.
* More time will be required for additional inspections and repairs if scribe lines or
other damage is found.
* More time may be required for inspections around large repair doublers.
Group 3:
Scribe Line Inspection
Elapsed HoursTask HoursNumber of PersonsTask
20.080.04Figure 3
6.012.02Figure 7
2.04.02Figure 9
28.0 *96.0 *TOTAL FOR EACH AIRPLANE
* Total Task Hours and Elapsed Hours dependent upon total number of fuselage
areas being inspected.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 26, 2013
A3539
37 of 110
BOEING SERVICE BULLETIN A3539
ALERTALERT

### Page 38

Group 3:
Scribe Line Inspection
Elapsed HoursTask HoursNumber of PersonsTask
* Additional time is required for paint and sealant removal.
* More time will be required for additional inspections and repairs if scribe lines or
other damage is found.
* More time may be required for inspections around large approved repairs.
Group 4:
Scribe Line Inspection
Elapsed HoursTask HoursNumber of PersonsTask
20.080.04Figure 4
6.012.02Figure 8
2.04.02Figure 9
28.0 *96.0 *TOTAL FOR EACH AIRPLANE
* Total Task Hours and Elapsed Hours dependent upon total number of fuselage
areas being inspected.
* Additional time is required for paint and sealant removal.
* More time will be required for additional inspections and repairs if scribe lines or
other damage is found.
* More time may be required for inspections around large approved repairs.
Group 5:
Scribe Line Inspection
Elapsed HoursTask HoursNumber of PersonsTask
24.096.04Figure 11
24.0 *96.0 *TOTAL FOR EACH AIRPLANE
* Total Task Hours and Elapsed Hours dependent upon total number of fuselage
areas being inspected.
* Additional time is required for paint and sealant removal.
* More time will be required for additional inspections and repairs if scribe lines or
other damage is found.
* More time may be required for inspections around large approved repairs.
H. Weight and Balance Changes
None.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 26, 2013
A3539
38 of 110
BOEING SERVICE BULLETIN A3539
ALERTALERT

### Page 39

I. Electrical Load Data
Not changed.
J. References
1. Existing Data:
a. Boeing Service Related Problem (SRP) 707-SRP-53-0247
b. Standard Overhaul Practices Manual (SOPM) 20-30-03, 20-43-03
c. 707 Non-Destructive Testing (NDT) Manual Part 10, 53-30-01; Part 4, 53-30-05; Part 4,
53-30-06; Part 6, 51-00-00, Figure 23; Part 6, 51-00-00, Figure 4; Part 6, 53-30-22; TR 06-10,
Part 6, 53-30-24; TR 06-11, Part 6, 53-30-25; TR 06-12, Part 6, 53-30-26
d. 707 Aircraft Maintenance Manual (AMM) 51-2-141, 51-3-0
e. Service Bulletin Index Document D6-1647 Part 3
2. Data Supplied with this Service Bulletin:
None.
3. Installation Drawings Used in the Preparation of this Service Bulletin:
None.
K. Publications Affected
1. Publications
Chapter-SectionPublication
51-2707 Aircraft Maintenance Manual
2. Damage Tolerance Based Structural Inspections:
Boeing has evaluated the repairs and/or changes in this service bulletin for effects on Fatigue
Critical Structure (FCS) and for changes to Damage Tolerance Inspections (DTI) required in the
Maintenance Program. This service bulletin affects FCS but no new DTIs are necessary.
L. Interchangeability and Intermixability of Parts
Accomplishment of this service bulletin does not affect interchangeability or intermixability of parts.
M. Software Accomplishment Summary
Not affected.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 26, 2013
A3539
39 of 110
BOEING SERVICE BULLETIN A3539
ALERTALERT

### Page 40

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 26, 2013
A3539
40 of 110
BOEING SERVICE BULLETIN A3539
ALERTALERT
BLANK PAGE

### Page 41

2.    MATERIAL INFORMATION
A. Material - Price and Availability
None.
B. Industry Support Information
Boeing warranty remedies are not available for the inspections or repair procedures given in this service
bulletin.
C. Parts Necessary for Each Airplane
1. Kits/Parts:
None.
2. Parts and Materials Supplied by the Operator:
NotesNameQTYPart Number /
Specification
(b) (c) (g)Chemical Conversion Coating10 OuncesType 2, Class A
(a) (c) (g)Primer24 OuncesBMS 10-11 Type 1
(a) (c) (d) (e) (f) (g)Primer Plus Enamel24 OuncesBMS 10-72
(a) (c) (d) (e) (f) (g)Primer24 OuncesBMS 10-79, Type II
(a) (c) (d) (e) (f) (g)Topcoat24 OuncesBMS 10-60, Type II
(a) Refer to the Qualified Products List at the end of the Boeing Material Specification (BMS) for supplier
data.
(b) Refer to SOPM 20-43-03 as an accepted procedure for material sources.
(c) This part is only necessary if paint is removed.
(d) This part is only necessary if BMS 10-79 and BMS 10-60 or the operators normal decorative paint system
is not used.
(e) This part is only necessary if BMS 10-72 or the operators normal decorative paint system is not used.
(f) Refer to 707 AMM 51-2-141 as an accepted procedure for decorative exterior paint system application.
(g) The quantity given is an approximation. The actual quantity required will vary depending on the results
of the scribe line inspections.
3. Parts Modified and Reidentified:
None.
4. Parts Removed and Not Replaced:
None.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 26, 2013
A3539
41 of 110
BOEING SERVICE BULLETIN A3539
ALERTALERT

### Page 42

D. Parts Necessary to Change Spares
None.
E. Special Tooling - Price and Availability
The operator can supply the tools shown in Paragraph 2.F., Special Tooling Necessary to do this
Service Bulletin. Tool price and supply data are not given.
F. Special Tooling Necessary to do this Service Bulletin
No special tooling is necessary to accomplish this bulletin. However, the following standard tools may
be needed to measure scribe line depth. These tools are unusual and may not be available at all shops
as standard tools. Maintenance and overhaul tools in the manuals shown in Paragraph 1.J., References,
can also be necessary. Examine operator tool supply to make sure all necessary tools are available.
NameNumber
Digital Optical Micrometer (a) (b)Model Number 8400K
Optical Micrometer (a) (c)Model 966 (Part Number 125632-1) or
Model 966A (Part Number 125632)
Laser Measurement System (d)Inspect Cam Model SDMS
These are typical optical micrometers.(a)
Rene Company(b)
1005 South Mountain Avenue
Monrovia, California 91016 USA
Toll free: (866) 358-9955
Tel: (626) 358-9955
Fax: (626) 358-1448
Email: info@renecompany.com
Taber Industries(c)
455 Bryant Street
North Tonawanda, New York 14120 USA
Toll-Free: (800) 333-5300 (in USA or Canada)
Phone: (716) 694-4000
Fax: (716) 694-1450
Refer to 707 NDT Manual Part 10, 53-30-01 for the latest vendor information.(d)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 26, 2013
A3539
42 of 110
BOEING SERVICE BULLETIN A3539
ALERTALERT

### Page 43

3.    ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL INFORMATION
CAUTION: ELECTRICALLY GROUND THE AIRPLANE. THIS WILL HELP TO PREVENT DAMAGE
TO THE AIRPLANE OR EQUIPMENT.
CAUTION: KEEP THE WORK AREA, WIRES AND ELECTRICAL BUNDLES CLEAN OF METAL
PARTICLES OR CONTAMINATION WHEN YOU USE TOOLS. UNWANTED MATERIAL,
METAL PARTICLES OR CONTAMINATION CAUGHT IN WIRE BUNDLES CAN CAUSE
DAMAGE TO THE BUNDLES. DAMAGED WIRE BUNDLES CAN CAUSE SPARKS OR
OTHER ELECTRICAL DAMAGE.
NOTE: 1. Manual titles are referred to by acronyms. Refer to Paragraph 1.J., References, for
definition of the acronyms.
2. Obey all of the warnings and cautions given in the specified manual sections.
3. Unless shown differently, these dimensions and tolerances are used:
– Linear dimensions are in inches
– Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus
or minus 0.03 inch
4. These work instructions refer to procedures included in other Boeing documents.
When the words "refer to" are used and the operator has an accepted alternative
procedure, the accepted alternative procedure can be used. When the words "in
accordance with" are included in the instruction, the procedure in the Boeing document
must be used.
5. Appendix D includes information for the fabrication or purchase of a scribe line sample
for use as a training aid. The use of this sample is not required when performing
actions of this service bulletin. This sample is an aid in identifying what a scribe line
may look and feel like but is not intended to show all damage that is considered a
scribe line. When identifying scribe lines, see the definition of a typical scribe line in
the Accomplishment Instructions of this service bulletin.
6. If an optical micrometer or laser measurement system cannot be used because the
upper skin of the lap joint covers a scribe line, then the scribe line depth does not
need to be determined at that location. These scribe lines must be considered typical
and therefore all inspection and other requirements for a typical scribe line apply.
7. It is required that individuals performing ultrasonic inspections on airplanes with
scribe lines to detect cracks per the relevant procedures must be recognized by the
operator or repair station as qualified to perform ultrasonic inspections on their
airplanes and meet at least one of the following criteria:
– The individual must be qualified to at least Level 2 in the ultrasonic method in
accordance with an accepted industry standard, i.e. ATA Specification 105,
Mil-Std.-410, NAS-410, SNT-TC-1A, or EN-4179 or equivalent. or
– The individual has received specific Boeing training with Boeing providing a
certificate stating that the individual has satisfactorily completed the training in
the specific techniques. or
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 26, 2013
A3539
43 of 110
BOEING SERVICE BULLETIN A3539
ALERTALERT

### Page 44

– The individual has a Level 1 rating in the ultrasonic method in accordance with
an accepted industry standard and has received specific training and a statement
from the qualifying entity (employer) that the individual is qualified for this
particular inspection.
8. If scribe lines are found during any of the inspections contained in this service bulletin,
when determining the requirements for inspection and repair, each scribe line shall
be considered individually.
9. An external approved repair is identified as any SRM repair, a repair provided and
approved by Boeing for a specific case requested by the operator, or an operator
developed repair that has a Boeing approved Damage Tolerance Analysis.
10. If a scribe line is found outside of the inspections areas in this service bulletin, do
inspections in accordance with Work Instructions, Paragraph 3.B.10 - Part 8.
11. If any scribe line is detected at a non-approved repair, provide details of repair and
scribe line to Boeing for evaluation. Do the Boeing recommended disposition.
12. A Detailed Inspection is defined as: An intensive examination of a specific item,
installation, or assembly to detect damage, failure, or irregularity. Available lighting
is normally supplemented with a direct source of good lighting at an intensity deemed
appropriate. Inspection aids such as mirrors, magnifying lenses, etc. may be
necessary. Surface cleaning and elaborate procedures may be required.
13. Boeing has developed training video VPS13290, "Preventing Scribe Damage Through
Proper Sealant Removal". To get this video, operators should contact their local
Boeing Field Service Representative.
14. Operators should thoroughly familiarize themselves with all Parts and Work
Instructions in this service bulletin prior to starting their scribe line inspection program.
In addition, it is recommended that all Non-Destructive Testing (NDT) procedures
be reviewed and limitations understood prior to the use of the NDT inspection. This
will aid in understanding all available options in the event a scribe line is discovered.
15. Inspection Exemptions: Certain inspections are not required under these conditions:
– Skin Lap Joints: Inspections are not required in skin lap joint areas where an
existing external approved repair covers a potential scribe line, provided the
repair spans a minimum of three fastener rows above and three fastener rows
below the potential scribe line location. External repairs that do not meet this
requirement must be removed to allow skin lap joint inspection.
– If operator's records show that the airplane has never been stripped or repainted
since delivery from Boeing then the skin lap joint and external approved repair
scribe line inspections are not required, except as noted below:
– If a decal is installed, or was previously installed, across an area that
requires inspection, the inspection exemption does not apply. The skin lap
joint and external approved repair inspection must still be done for the
affected area at the compliance time in accordance with this service bulletin.
16. Do not blend scribe lines. Blending a scribe line may hinder inspection techniques
necessary to determine the presence or absence of fatigue cracks.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 26, 2013
A3539
44 of 110
BOEING SERVICE BULLETIN A3539
ALERTALERT

### Page 45

B. WORK INSTRUCTIONS
1. IDENTIFICATION OF A "TYPICAL" SCRIBE LINE
Determine if the Scribe Line is "typical".
A scribe line is defined as a narrow, shallow, distinct line of damage (typically up to 0.006 inch
deep), usually associated with the removal of a fillet or gap seal (lap joints and butt joints,
respectively). Scribe lines can be both tactile and non-tactile. Discoloration of the aluminum clad
layer or small surface imperfections do not qualify as a scribe line. A lightning strike at a lap joint
or butt joint does not qualify as a scribe line. In certain cases, the scribe lines have been associated
with the trimming of fuselage skin decals. Scribe lines that create a potential safety concern are
generally long continuous scribe lines or several adjacent scribe lines in a critical orientation at
specific locations with relatively high stresses.
If an optical micrometer or laser measurement system cannot be used because the upper skin of
the lap joint covers a scribe line, then the scribe line depth does not need to be determined at that
location. These scribe lines must be considered typical and therefore all inspection and other
requirements for a typical scribe line apply.
Grinding, gouging, or other "non-typical" damage, which is more significant (deeper or locally more
extensive) than the typical scribe line must be repaired. Localized scratches, nicks and dents that
might be induced in other areas of the fuselage skin during either manufacture or maintenance
operations are not considered scribe lines. This type of damage should be addressed via the
acceptable maintenance practices detailed in the Structural Repair Manual.
2. LOCATIONS OF "TYPICAL" SCRIBE LINES
a. Skin Lap Joints
In areas near skin lap joints, scribe lines normally run parallel to the lap joint in the lower skin
along the edge of the upper skin. These scribe lines are typically within 0.25 inch of the lower
edge of the upper skin. In some cases, portions of the scribe lines may be directly adjacent
to or slightly under the lower edge of the upper skin resulting in hidden lines that cannot be
viewed without disassembly. The ends of these scribe lines sometimes may also turn slightly
away from the lap joint.
b. Skin Butt Joints
In butt joint areas, scribe lines are normally found on the splice plate in the gap between the
forward and aft skin edges and run along the butt joint.
c. External Approved Repairs
In areas around external approved repairs, scribe lines normally follow the periphery of the
external approved repairs.
d. External Features
In areas around external features, scribe lines normally follow the periphery of the external
feature.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 26, 2013
A3539
45 of 110
BOEING SERVICE BULLETIN A3539
ALERTALERT

### Page 46

e. Decals and Fairings
In areas around decals and fairings, scribe lines normally follow the periphery of the decal or
fairing. Scribe lines may be located anywhere on a skin panel where decals or fairings are
currently installed or were previously were installed.
3. PART 1 - SURFACE PREPARATION - SCRIBE LINE INSPECTIONS
NOTE: Refer to Appendix A of this service bulletin for an accepted procedure for sealant removal
during surface preparation.
a. Skin Lap Joint Surface Preparation
(1) Remove the sealant from the lower edge of all affected lap joints.
(2) Remove the paint from below the lower edge of all affected lap joints. The bared area
should be at least one (1.0) inch wide, as measured from the lower edge of the upper
skin.
(3) If any section of the affected lap joints is under the wing-to-body fairing, remove the
appropriate fairing panel(s) for access.
b. Skin Butt Joint Surface Preparation
Remove the sealant from within the gap of the affected butt joints. It is recommended that the
primer and paint, if present, not be removed from the butt joint splice plate. If the primer is
removed, do not use chemical stripper.
c. External Approved Repair Surface Preparation
Remove paint and sealant from the area of the skin around the periphery of the external
approved repair. The bared area should be at least one (1.0) inch wide, around the periphery
of the external approved repair.
d. External Feature Surface Preparation
Remove paint and sealant from the area of the skin around the periphery of the external
feature. The bared area should be at least one (1.0) inch wide, around the periphery of the
external feature.
e. Decal and Fairing Surface Preparation
Remove the paint from the applicable area of the skin around the edges of the decal or fairing
as follows:
(1) If decals were previously installed, and it can be determined where the edges of the
decals previously were, remove the paint from the area of the skin around the edges of
the decal. The bared area should be at least one half (0.5) inch wide on both sides of the
edge of the decal.
(2) If decals were previously installed, but it cannot be determined where the edges of the
decal were, remove the paint from all of the affected decal locations.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 26, 2013
A3539
46 of 110
BOEING SERVICE BULLETIN A3539
ALERTALERT

### Page 47

(3) For fairings, remove paint and sealant from the area of the skin around the periphery of
the fairing. The bared area should be at least one (1.0) inch wide, around the periphery
of the fairing.
4. PART 2 - DETAILED INSPECTION FOR SCRIBE LINES
a. Do a detailed inspection of the fuselage skin for scribe lines. Use a minimum 10X magnifying
lens to aid the inspection.
b. From the tables that follow, which correspond to airplane group numbers, determine the
applicable figures for the inspection areas to be inspected.
c. If no scribe line is found, do Part 3 - No Scribe Line Found.
d. If any scribe line is found, do Part 4 - Scribe Line Found.
e. Scribe Line Inspections:
Group 1:
Table 1 - Scribe Line Inspections
Area
Figure 1Skin Lap Joints
Figure 5External Approved Repairs
Figure 9External Features
Group 2:
Table 2 - Scribe Line Inspections
Area
Figure 2Skin Lap Joints
Figure 6External Approved Repairs
Figure 9External Features
Group 3:
Table 3 - Scribe Line Inspections
Area
Figure 3Skin Lap Joints
Figure 7External Approved Repairs
Figure 9External Features
Group 4:
Table 4 - Scribe Line Inspections
Area
Figure 4Skin Lap Joints
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 26, 2013
A3539
47 of 110
BOEING SERVICE BULLETIN A3539
ALERTALERT

### Page 48

Group 4:
Table 4 - Scribe Line Inspections
Area
Figure 8External Approved Repairs
Figure 9External Features
Group 5:
Table 5 - Scribe Line Inspections
Area
Figure 11Skin Lap Joints
Figure 11External Approved Repairs
Figure 11External Features
Figure 11Skin Butt Joints
Figure 11Decals
5. PART 3 - NO SCRIBE LINE IS FOUND
a. If no scribe lines are found, no further inspections are required.
b. Do Part 7 - Surface Finish Restoration.
6. PART 4 - ANY SCRIBE LINE IS FOUND
NOTE: DO NOT BLEND ANY SCRIBE LINE. BLENDING A SCRIBE LINE MAY HINDER
INSPECTION TECHNIQUES NECESSARY TO DETERMINE THE PRESENCE OR
ABSENCE OF FATIGUE CRACKS.
a. Measure and document the location and depth of all scribe lines that are found. It is
recommended that you use the format outlined in Appendix C to document the scribe line.
b. Do a laser measurement inspection or the optical micrometer inspection to measure the
maximum depth of the scribe line.
NOTE: Only the laser measurement inspection in accordance with 707 NDT Manual Part
10, 53-30-01 can be used to confirm scribe line depth less than 0.001 inch.
c. If the scribe line depth is less than 0.001 inch:
(1) No repair or further inspections are required at that location.
(2) Do Part 7 - Surface Finish Restoration of this Service Bulletin.
d. Group 1-4:
If the scribe line depth is greater than or equal to 0.001 inch:
(1) Do Part 5 - Non-Destructive Testing (NDT) Inspections - Scribe Lines to detect any crack.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 26, 2013
A3539
48 of 110
BOEING SERVICE BULLETIN A3539
ALERTALERT

### Page 49

NOTE: The applicable NDT inspection(s) of the scribe line must be accomplished prior
to a repair proposal to verify that no crack exists in or around the scribe line.
(2) Do Part 7 - Surface Finish Restoration of this Service Bulletin.
e. Group 5:
If the scribe line depth is greater than or equal to 0.001 inch:
(1) Contact Boeing for repair instructions and do the repair.
(2) Do Part 7 - Surface Finish Restoration of this Service Bulletin.
7. Group 1-4:
PART 5 - NON-DESTRUCTIVE TESTING (NDT) INSPECTIONS - SCRIBE LINES
If the scribe line depth is greater than or equal to 0.001 inch, do what follows:
a. Scribe Line at Skin Lap Joint:
(1) Do the applicable NDT inspection in accordance with FIGURE 10.
NOTE: The skin thickness must be known when conducting the Ultrasonic (UT)
inspections so that the correct reference standard is used in calibration. The
707 NDT Manual Part 4, 53-30-05 (Ultrasonic Single Element) has application
limitations based upon skin thickness.
Use the applicable Boeing drawing to determine skin thickness if skin thickness is not
known.
(2) If no crack is found and the scribe line depth is greater than or equal to 0.001 inch and
less than or equal to 0.006 inch, do one of the options that follows:
(a) Do the Limited Return To Service (LRTS) repeat inspection program in accordance
with Part 6 of this service bulletin.
or
(b) Document and propose a repair to Boeing. Do the repair. This will assist Boeing in
the analysis of the scribe line damage and repair proposal.
NOTE: A repair is not required until the repair compliance time is reached, provided
the operator chooses to do the LRTS repeat inspection program in
accordance with Part 6 of this service bulletin.
A repair proposal is only required if the operator has chosen not to do the
LRTS repeat inspection program.
(3) If no crack is found and the scribe line depth is greater than 0.006 inch, document and
propose a repair to Boeing. Do the repair. This will assist Boeing in the analysis of the
scribe line damage and repair proposal.
NOTE: The LRTS repeat inspection program is not an option for scribe lines greater
than 0.006 inch deep.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 26, 2013
A3539
49 of 110
BOEING SERVICE BULLETIN A3539
ALERTALERT

### Page 50

(4) If any crack is found, document and propose a repair to Boeing. Do the repair. This will
assist Boeing in the analysis of the crack and repair proposal.
(5) Do Part 7 - Surface Finish Restoration of this service bulletin.
b. Scribe Line at External Approved Repair:
(1) Do the applicable NDT inspection in accordance with FIGURE 10.
NOTE: The skin thickness must be known when conducting the Ultrasonic (UT)
inspections so that the correct reference standard is used in calibration. The
707 NDT Manual Part 4, 53-30-05 (Ultrasonic Single Element) has application
limitations based upon skin thickness.
Use the applicable Boeing drawing to determine skin thickness if skin thickness is not
known.
(2) If no crack is found and the scribe line depth is greater than or equal to 0.001 inch and
less than or equal to 0.006 inch, do one of the options that follows:
(a) Do the Limited Return To Service (LRTS) repeat inspection program in accordance
with Part 6 of this service bulletin.
or
(b) Document and propose a repair to Boeing. Do the repair. This will assist Boeing in
the analysis of the scribe line damage and repair proposal.
NOTE: A repair is not required until the repair compliance time is reached, provided
the operator chooses to do the LRTS repeat inspection program in
accordance with Part 6 of this service bulletin.
A repair proposal is only required if the operator has chosen not to do the
LRTS repeat inspection program.
(3) If no crack is found and the scribe line depth is greater than 0.006 inch, document and
propose a repair to Boeing. Do the repair. This will assist Boeing in the analysis of the
scribe line damage and repair proposal.
NOTE: The LRTS repeat inspection program is not an option for scribe lines greater
than 0.006 inch deep.
(4) If any crack is found, document and propose a repair to Boeing. Do the repair. This will
assist Boeing in the analysis of the crack and repair proposal.
(5) Do Part 7 - Surface Finish Restoration of this service bulletin.
c. Scribe Line at External Feature:
(1) Do the applicable NDT inspection in accordance with FIGURE 10.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 26, 2013
A3539
50 of 110
BOEING SERVICE BULLETIN A3539
ALERTALERT

### Page 51

NOTE: The skin thickness must be known when conducting the Ultrasonic (UT)
inspections so that the correct reference standard is used in calibration. The
707 NDT Manual Part 4, 53-30-05 (Ultrasonic Single Element) has application
limitations based upon skin thickness.
Use the applicable Boeing drawing to determine skin thickness if skin thickness is not
known.
(2) If no crack is found and the scribe line depth is greater than or equal to 0.001 inch and
less than or equal to 0.006 inch, do one of the options that follows:
(a) Do the Limited Return To Service (LRTS) repeat inspection program in accordance
with Part 6 of this service bulletin.
or
(b) Document and propose a repair to Boeing. Do the repair. This will assist Boeing in
the analysis of the scribe line damage and repair proposal.
NOTE: A repair is not required until the repair compliance time is reached, provided
the operator chooses to do the LRTS repeat inspection program in
accordance with Part 6 of this service bulletin.
A repair proposal is only required if the operator has chosen not to do the
LRTS repeat inspection program.
(3) If no crack is found and the scribe line depth is greater than 0.006 inch, document and
propose a repair to Boeing. Do the repair. This will assist Boeing in the analysis of the
scribe line damage and repair proposal.
NOTE: The LRTS repeat inspection program is not an option for scribe lines greater
than 0.006 inch deep.
(4) If any crack is found, document and propose a repair to Boeing. Do the repair. This will
assist Boeing in the analysis of the crack and repair proposal.
(5) Do Part 7 - Surface Finish Restoration of this service bulletin.
8. Group 1-4:
PART 6 - LIMITED RETURN TO SERVICE (LRTS) PROGRAM
a. Skin Lap Joints - Repeat Inspection:
(1) Determine which areas of the skin lap joints require repeat inspection based upon previous
inspection results.
(2) Do Part 1 - Surface Preparation - Scribe Line Inspection, in areas that require repeat
inspection.
(3) Do Part 2 - Detailed Inspection for Scribe Lines, in areas that require repeat inspection.
(4) Do the applicable NDT inspection in accordance with FIGURE 10.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 26, 2013
A3539
51 of 110
BOEING SERVICE BULLETIN A3539
ALERTALERT

### Page 52

NOTE: The skin thickness must be known when conducting the Ultrasonic (UT)
inspections so that the correct reference standard is used in calibration. The
707 NDT Manual Part 4, 53-30-05 (Ultrasonic Single Element) has application
limitations based upon skin thickness.
Use the applicable Boeing drawing to determine skin thickness if skin thickness is not
known.
(5) If no crack is found, do one of the options that follows:
(a) Document and propose a repair to Boeing. Do the repair. This will assist Boeing in
the analysis of the scribe line damage and repair proposal.
or
(b) Repeat the LRTS program in accordance with this service bulletin. Contact Boeing
before the compliance time listed in Paragraph 1.E for additional inspections or repair.
Do the additional inspections or repair.
(6) If any crack is found, document and propose a repair to Boeing. Do the repair. This will
assist Boeing in the analysis of the crack and repair proposal.
(7) Do Part 7 - Surface Finish Restoration of this service bulletin.
b. External Approved Repair - Repeat Inspection:
(1) Determine which areas of the external approved repairs require repeat inspection based
upon previous inspection results.
(2) Do Part 1 - Surface Preparation - Scribe Line Inspection, in areas that require repeat
inspection.
(3) Do Part 2 - Detailed Inspection for Scribe Lines, in areas that require repeat inspection.
(4) Do the applicable NDT inspection in accordance with FIGURE 10.
NOTE: The skin thickness must be known when conducting the Ultrasonic (UT)
inspections so that the correct reference standard is used in calibration. The
707 NDT Manual Part 4, 53-30-05 (Ultrasonic Single Element) has application
limitations based upon skin thickness.
Use the applicable Boeing drawing to determine skin thickness if skin thickness is not
known.
(5) If no crack is found, do one of the options that follows:
(a) Document and propose a repair to Boeing. Do the repair. This will assist Boeing in
the analysis of the scribe line damage and repair proposal.
or
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 26, 2013
A3539
52 of 110
BOEING SERVICE BULLETIN A3539
ALERTALERT

### Page 53

(b) Repeat the LRTS program in accordance with this service bulletin. Contact Boeing
before the compliance time listed in Paragraph 1.E for additional inspections or repair.
Do the additional inspections or repair.
(6) If any crack is found, document and propose a repair to Boeing. Do the repair. This will
assist Boeing in the analysis of the crack and repair proposal.
(7) Do Part 7 - Surface Finish Restoration of this service bulletin.
c. External Features - Repeat Inspection:
(1) Determine which areas of the external features require repeat inspection based upon
previous inspection results.
(2) Do Part 1 - Surface Preparation - Scribe Line Inspection, in areas that require repeat
inspection.
(3) Do Part 2 - Detailed Inspection for Scribe Lines, in areas that require repeat inspection.
(4) Do the applicable NDT inspection in accordance with FIGURE 10.
NOTE: The skin thickness must be known when conducting the Ultrasonic (UT)
inspections so that the correct reference standard is used in calibration. The
707 NDT Manual Part 4, 53-30-05 (Ultrasonic Single Element) has application
limitations based upon skin thickness.
Use the applicable Boeing drawing to determine skin thickness if skin thickness is not
known.
(5) If no crack is found, do one of the options that follows:
(a) Document and propose a repair to Boeing. Do the repair. This will assist Boeing in
the analysis of the scribe line damage and repair proposal.
or
(b) Repeat the LRTS program in accordance with this service bulletin. Contact Boeing
before the compliance time listed in Paragraph 1.E for additional inspections or repair.
Do the additional inspections or repair.
(6) If any crack is found, document and propose a repair to Boeing. Do the repair. This will
assist Boeing in the analysis of the crack and repair proposal.
(7) Do Part 7 - Surface Finish Restoration of this service bulletin.
9. PART 7 - SURFACE FINISH RESTORATION
NOTE: To reduce the possibility of future scribing, Boeing recommends that the BMS 5-95 fillet
seal not be reapplied except as follows:
1. In the gap at butt joints.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 26, 2013
A3539
53 of 110
BOEING SERVICE BULLETIN A3539
ALERTALERT

### Page 54

2. The leading edge of the external approved repair for repairs that will be inspected
under the LRTS program.
3. Around external features as referred to in the applicable Aircraft Maintenance
Manual (AMM) section.
a. Refinish the external surface finish as follows:
(1) Apply Type 2, Class A chemical conversion coating. Refer to SOPM 20-43-03 as an
accepted procedure.
(2) Apply BMS 10-72 paint system (primer plus enamel), or BMS 10-79 Type II (primer) plus
BMS 10-60 Type II (topcoat), or the operator's normal decorative paint system. Refer to
707 Aircraft Maintenance Manual 51-2-141 as an accepted procedure.
b. Refinish the internal surface finish as follows:
(1) Apply Type 2, Class A chemical conversion coating. Refer to SOPM 20-43-03 as an
accepted procedure.
(2) Apply BMS 10-11 Type 1 primer. Refer to 707 Aircraft Maintenance Manual Subject
51-2-141 as an accepted procedure.
c. For external approved repairs that will be inspected under the LRTS program, apply a fillet
seal of BMS 5-95 sealant at the leading edge of the external approved repair. Refer to 707
Aircraft Maintenance Manual Subject 51-3-0 as an accepted procedure.
d. For external approved repairs around which no scribe lines were found, apply a fillet seal of
BMS 5-95 sealant around the periphery of the external approved repair. Refer to 707 Aircraft
Maintenance Manual Subject 51-3-0 as an accepted procedure.
e. Put the airplane back to a serviceable condition.
10. Group 1-4:
PART 8 - KNOWN EXISTING SCRIBE LINE DAMAGE - OUTSIDE OF SERVICE BULLETIN
INSPECTION AREAS
If scribe lines are found outside of service bulletin inspection areas, do what follows:
a. Do Part 1 - Surface Preparation - Scribe Line Inspections of this service bulletin.
b. Measure and document the location and depth of all scribe lines that are found. It is
recommended that you use the format outlined in Appendix C to document the scribe line.
c. Do a laser measurement inspection or the optical micrometer inspection to measure the
maximum depth of the scribe line.
NOTE: Only the laser measurement inspection in accordance with 707 NDT Manual Part
10, 53-30-01 can be used to confirm scribe line depth less than 0.001 inch.
d. If the scribe line depth is less than 0.001 inch:
(1) No repair or further inspections are required.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 26, 2013
A3539
54 of 110
BOEING SERVICE BULLETIN A3539
ALERTALERT

### Page 55

(2) Do Part 7 - Surface Finish Restoration of this Service Bulletin.
e. If the scribe line depth is greater than or equal to 0.001 inch, do what follows:
(1) Scribe Line at Skin Lap Joint - NDT Inspection
(a) Do the applicable NDT inspection in accordance with FIGURE 10.
NOTE: The skin thickness must be known when conducting the Ultrasonic (UT)
inspections so that the correct reference standard is used in calibration.
The 707 NDT Manual Part 4, 53-30-05 (Ultrasonic Single Element) has
application limitations based upon skin thickness.
Use the applicable Boeing drawing to determine skin thickness if skin thickness is
not known.
(b) If no crack is found and the scribe line depth is greater than or equal to 0.001 inch
and less than or equal to 0.004 inch, no repair or further inspections are required.
(c) If no crack is found and the scribe line depth is greater than 0.004 inch and less than
or equal to 0.006 inch, contact Boeing for additional inspections or repair. Do the
additional inspections or repair.
(d) If no crack is found and the scribe line depth is greater than 0.006 inch, document
and propose a repair to Boeing. Do the repair. This will assist Boeing in the analysis
of the scribe line damage and repair proposal.
(e) If any crack is found, document and propose a repair to Boeing. Do the repair. This
will assist Boeing in the analysis of the crack and repair proposal. Contact Boeing
for additional inspections. Do the additional inspections.
(f) Do Part 7 - Surface Finish Restoration of this Service Bulletin.
(2) Scribe Line at External Approved Repair - NDT Inspection
(a) Do the applicable NDT inspection in accordance with FIGURE 10.
NOTE: The skin thickness must be known when conducting the Ultrasonic (UT)
inspections so that the correct reference standard is used in calibration.
The 707 NDT Manual Part 4, 53-30-05 (Ultrasonic Single Element) has
application limitations based upon skin thickness.
Use the applicable Boeing drawing to determine skin thickness if skin thickness is
not known.
(b) If no crack is found and the scribe line depth is greater than or equal to 0.001 inch
and less than or equal to 0.004 inch, no repair or further inspections are required.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 26, 2013
A3539
55 of 110
BOEING SERVICE BULLETIN A3539
ALERTALERT

### Page 56

(c) If no crack is found and the scribe line depth is greater than 0.004 inch and less than
or equal to 0.006 inch, contact Boeing for additional inspections or repair. Do the
additional inspections or repair.
(d) If no crack is found and the scribe line depth is greater than 0.006 inch, document
and propose a repair to Boeing. Do the repair. This will assist Boeing in the analysis
of the scribe line damage and repair proposal.
(e) If any crack is found, document and propose a repair to Boeing. Do the repair. This
will assist Boeing in the analysis of the crack and repair proposal. Contact Boeing
for additional inspections. Do the additional inspections.
(f) Do Part 7 - Surface Finish Restoration of this Service Bulletin.
(3) Scribe Line at External Feature - NDT Inspection
(a) Do the applicable NDT inspection in accordance with FIGURE 10.
NOTE: The skin thickness must be known when conducting the Ultrasonic (UT)
inspections so that the correct reference standard is used in calibration.
The 707 NDT Manual Part 4, 53-30-05 (Ultrasonic Single Element) has
application limitations based upon skin thickness.
Use the applicable Boeing drawing to determine skin thickness if skin thickness is
not known.
(b) If no crack is found and the scribe line depth is greater than or equal to 0.001 inch
and less than or equal to 0.004 inch, no repair or further inspections are required.
(c) If no crack is found and the scribe line depth is greater than 0.004 inch and less than
or equal to 0.006 inch, contact Boeing for additional inspections or repair. Do the
additional inspections or repair.
(d) If no crack is found and the scribe line depth is greater than 0.006 inch, document
and propose a repair to Boeing. Do the repair. This will assist Boeing in the analysis
of the scribe line damage and repair proposal.
(e) If any crack is found, document and propose a repair to Boeing. Do the repair. This
will assist Boeing in the analysis of the crack and repair proposal. Contact Boeing
for additional inspections. Do the additional inspections.
(f) Do Part 7 - Surface Finish Restoration of this Service Bulletin.
(4) Scribe Line at Skin Butt Joint - NDT Inspection
(a) Based upon scribe line location, do the applicable NDT inspection in accordance
with what follows:
1) Low Frequency Eddy Current (LFEC) in accordance with 707 NDT Manual TR
06-10, Part 6, 53-30-24.
or
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 26, 2013
A3539
56 of 110
BOEING SERVICE BULLETIN A3539
ALERTALERT

### Page 57

2) High Frequency Eddy Current (HFEC) in accordance with 707 NDT Manual TR
06-11, Part 6, 53-30-25.
(b) If no crack is found and the scribe line depth is greater than or equal to 0.001 inch
and less than or equal to 0.004 inch, no repair or further inspections are required.
(c) If no crack is found and the scribe line depth is greater than 0.004 inch and less than
or equal to 0.006 inch, contact Boeing for additional inspections or repair. Do the
additional inspections or repair.
(d) If no crack is found and the scribe line depth is greater than 0.006 inch, document
and propose a repair to Boeing. Do the repair. This will assist Boeing in the analysis
of the scribe line damage and repair proposal.
(e) If any crack is found, document and propose a repair to Boeing. Do the repair. This
will assist Boeing in the analysis of the crack and repair proposal. Contact Boeing
for additional inspections. Do the additional inspections.
(f) Do Part 7 - Surface Finish Restoration of this Service Bulletin.
(5) Scribe Line at Decals and Fairings - NDT Inspection
(a) Do a High Frequency Eddy Current (HFEC) inspection in accordance with 707 NDT
Manual Part 6, 51-00-00, Figure 4 or 707 NDT Manual Part 6, 51-00-00, Figure 23
to detect any crack at any affected decals and fairings.
(b) If no crack is found and the scribe line depth is greater than or equal to 0.001 inch
and less than or equal to 0.004 inch, no repair or further inspections are required.
(c) If no crack is found and the scribe line depth is greater than 0.004 inch and less than
or equal to 0.006 inch, contact Boeing for additional inspections or repair. Do the
additional inspections or repair.
(d) If no crack is found and the scribe line depth is greater than 0.006 inch, document
and propose a repair to Boeing. Do the repair. This will assist Boeing in the analysis
of the scribe line damage and repair proposal.
(e) If any crack is found, document and propose a repair to Boeing. Do the repair. This
will assist Boeing in the analysis of the crack and repair proposal. Contact Boeing
for additional inspections. Do the additional inspections.
(f) Do Part 7 - Surface Finish Restoration of this Service Bulletin.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 26, 2013
A3539
57 of 110
BOEING SERVICE BULLETIN A3539
ALERTALERT

### Page 58 (OCR)

BOEING SERVICE BULLETIN A3539
ALERT  ALERT
This Figure applies only to: Group 1.
STA  S-24R  S-24L  STA  1384.10
STA  STA  089971 0111  STA  S-25R  1241  STA  1080  S-23R  100000000000000000  0000000000000000•  STA  1220  1064.10  S-25L  STA  STA  1265.20  1124.10  STA  STA  1303.70  1164.10
STA  1000  STA  960  S-20L S-29L
707-100B  STA  820  S-20R  S-18AR  LANDING  GEAR  DOOR  oco  o00  LANDING  GEAR  DOOR  S-18AL  INSPECTION AREA  EXISTING BUTT JOINT
•SECTION 43  S-30R  00000000000000  000
STA  600K
STA  600
STA  530  STA  SIA  STA STA
460
SECTION 41
2198830
FIGURE 1: FUSELAGE - SKIN LAP JOINTS - INSPECTION
(SHEET 1 OF 4)
Original Issue: April 26, 2013
PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  A3539
Work - See page 1 for details.  58 of 110

### Page 59 (OCR)

BOEING SERVICE BULLETIN A3539
ALERT  ALERT
FRAME
UPPER SKIN
STRINGER®
LOWER SKIN
1) TYPICAL SKI
• SCRIBE LIN
TYPICAL SKIN LAP JOINT
2198842
FIGURE 1: FUSELAGE - SKIN LAP JOINTS - INSPECTION
(SHEET 2 OF 4)
Original Issue: April 26, 2013
PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  A3539
Work - See page 1 for details.  59 of 110

### Page 60

The step numbers shown below agree with the numbers shown in the circle symbols in the figure.
CAUTION: DO NOT BLEND SCRIBE LINES. BLENDING A SCRIBE LINE MAY HINDER INSPECTION
TECHNIQUES NECESSARY TO DETERMINE THE PRESENCE OR ABSENCE OF FATIGUE
CRACKS.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
(a) (b)-S-30R, STA NLG To STA 481SkinInspect1
S-29R, STA 960 To STA 1124.10
S-29R, STA 1124.10 To STA
1265.20
S-25R, STA 312 To STA 360
S-25R, STA 360 To STA 481
S-24R, STA 1364.10 To STA 1440
S-20R, STA 259.50 To STA 360
S-20R, STA 360 To Door Cutout
S-20R, STA 580 To STA 600K
S-20R, STA 960 To Door Cutout
S-20R, Door Cutout To STA 1164.10
S-20R, STA 1164.10 To Door Cutout
S-20R, Door Cutout To STA 1265.20
S-14R, STA 360 To Door Cutout
S-14R, STA Door Cutout To STA
481
S-14R, STA 1124.10 To STA
1164.10
S-14R, STA 1241 To Door Cutout
S-14R, Door Cutout To STA 1364.10
S-10R, STA 1241 To STA 1384.10
S-6R, STA 441 To STA 580
S-6L, STA 441 To STA 481
S-14L, STA 360 To STA 481
S-14L, STA 1220 To Door Cutout
S-20L, STA 259.50 To STA 360
S-20L, STA 360 To STA 600
FIGURE 1: FUSELAGE - SKIN LAP JOINTS - INSPECTION
(SHEET 3 OF 4)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 26, 2013
A3539
60 of 110
BOEING SERVICE BULLETIN A3539
ALERTALERT

### Page 61

MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
S-20L, STA 960 To STA 1164.10
S-20L, STA 1164.10 To STA
1265.20
S-25L, STA 312 To STA 360
S-25L, STA 441 To STA 481
S-29L, STA 960 To STA 1124.10
S-29L, STA 1124.10 To STA
1265.20
(a) Do a detailed inspection of the fuselage skin for any scribe line. Use a minimum 10X magnifying lens
to aid the inspection.
(b) In areas near lap joints, scribe lines normally run parallel to the lap joint in the lower skin along the
edge of the upper skin. These scribe lines are typically within 0.25 inch of the lower edge of the upper
skin. In some cases, portions of the scribe lines may be directly adjacent to or slightly under the lower
edge of the upper skin. The ends of these scribe lines sometimes may also turn slightly away from the
lap joint.
FIGURE 1: FUSELAGE - SKIN LAP JOINTS - INSPECTION
(SHEET 4 OF 4)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 26, 2013
A3539
61 of 110
BOEING SERVICE BULLETIN A3539
ALERTALERT

### Page 62 (OCR)

BOEING SERVICE BULLETIN A3539
ALERT  ALERT
This Figure applies only to: Group 2.
S-24R  S-24L  STA  1384.10
STA  1265.20  S-23R  STA  1303.70
SECTION 46  STA  STA  1044.10 1144.10  STA  1241  STA  STO 1084.10  1200  STA  •00  00000  1220  STA  1024.10  S-25L  1124.10
STA  S-20R S-29R  LANDING  GEAR  DOOR  00000000000  000 00000000000  LANDING  GEAR  DOOR  S-20L S-29L
707-300  STA  820  S-18AR  000  INSPECTION AREA  -- EXISTING BUTT JOINT
SECTION 43  S-30R  000  .....  S-30L
STA  600K  00000000000  STA  600H
STA  600D
STA  600
STA  580  540
SECTION 41  S-25R  -20R  2198840
FIGURE 2: FUSELAGE - SKIN LAP JOINTS - INSPECTION
(SHEET 1 OF 4)
Original Issue: April 26, 2013
PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  A3539
Work - See page 1 for details.  62 of 110

### Page 63 (OCR)

BOEING SERVICE BULLETIN A3539
ALERT  ALERT
FRAME
UPPER SKIN
STRINGER®
LOWER SKIN
1) TYPICAL SKI
→ SCRIBE LIN
TYPICAL SKIN LAP JOINT
2198843
FIGURE 2: FUSELAGE - SKIN LAP JOINTS - INSPECTION
(SHEET 2 OF 4)
Original Issue: April 26, 2013
Export Controlled ECCN: 9E991 - BOEING  A3539
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  63 of 110

### Page 64

The step numbers shown below agree with the numbers shown in the circle symbols in the figure.
CAUTION: DO NOT BLEND SCRIBE LINES. BLENDING A SCRIBE LINE MAY HINDER INSPECTION
TECHNIQUES NECESSARY TO DETERMINE THE PRESENCE OR ABSENCE OF FATIGUE
CRACKS.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
(a) (b)-S-30R, STA NLG To STA 481SkinInspect1
S-29R, STA 960 To STA 1124.10
S-29R, STA 1124.10 To STA
1265.20
S-25R, STA 312 To STA 360
S-25R, STA 360 To STA 481
S-24R, STA 1364.10 To STA 1440
S-20R, STA 259.50 To STA 360
S-20R, STA 360 To Door Cutout
S-20R, STA 580 To STA 600K
S-20R, STA 960 To Door Cutout
S-20R, Door Cutout To STA 1164.10
S-20R, STA 1164.10 To Door Cutout
S-20R, Door Cutout To STA 1265.20
S-14R, STA 360 To Door Cutout
S-14R, Door Cutout To STA 481
S-14R, STA 1124.10 To STA
1164.10
S-14R, STA 1241 To Door Cutout
S-14R, Door Cutout To STA 1364.10
S-10R, STA 1241 To STA 1384.10
S-6R, STA 441 To STA 580
S-6L, STA 441 To STA 481
S-14L, STA 360 To STA 481
S-14L, STA 1220 To Door Cutout
S-20L, STA 259.50 To STA 360
S-20L, STA 360 To STA 441
S-20L, STA 441 To STA 600H
FIGURE 2: FUSELAGE - SKIN LAP JOINTS - INSPECTION
(SHEET 3 OF 4)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 26, 2013
A3539
64 of 110
BOEING SERVICE BULLETIN A3539
ALERTALERT

### Page 65

MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
S-20L, STA 960 To STA 1164.10
S-20L, STA 1164.10 To STA
1265.20
S-25L, STA 312 To STA 360
S-25L, STA 441 To STA 481
S-29L, STA 960 To STA 1124.10
S-29L, STA 1124.10 To STA
1265.20
(a) Do a detailed inspection of the fuselage skin for any scribe line. Use a minimum 10X magnifying lens
to aid the inspection.
(b) In areas near lap joints, scribe lines normally run parallel to the lap joint in the lower skin along the
edge of the upper skin. These scribe lines are typically within 0.25 inch of the lower edge of the upper
skin. In some cases, portions of the scribe lines may be directly adjacent to or slightly under the lower
edge of the upper skin. The ends of these scribe lines sometimes may also turn slightly away from the
lap joint.
FIGURE 2: FUSELAGE - SKIN LAP JOINTS - INSPECTION
(SHEET 4 OF 4)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 26, 2013
A3539
65 of 110
BOEING SERVICE BULLETIN A3539
ALERTALERT

### Page 66 (OCR)

BOEING SERVICE BULLETIN A3539
ALERT  ALERT
This Figure applies only to: Group 3.
OttL
VIS
VIS
VIS  LAZL
VIS  0OZ1
VIS
VIS  VIS  0801  00
VIS
VIS  028  00000000000  0000000000  767-S 70Z-S
800-202
o00  000
00000000000000  000
VIS  X009  00000000000  H009
VIS  a009
009
FIGURE 3: FUSELAGE - SKIN LAP JOINTS - INSPECTION
(SHEET 1 OF 4)
Original Issue: April 26, 2013
PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  A3539
Work - See page 1 for details.  66 of 110

### Page 67 (OCR)

BOEING SERVICE BULLETIN A3539
ALERT  ALERT
FRAME
UPPER SKIN
STRINGER®
LOWER SKIN
1) TYPICAL SKI
→ SCRIBE LIN
TYPICAL SKIN LAP JOINT
2198845
FIGURE 3: FUSELAGE - SKIN LAP JOINTS - INSPECTION
(SHEET 2 OF 4)
Original Issue: April 26, 2013
Export Controlled ECCN: 9E991 - BOEING  A3539
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  67 of 110

### Page 68

The step numbers shown below agree with the numbers shown in the circle symbols in the figure.
CAUTION: DO NOT BLEND SCRIBE LINES. BLENDING A SCRIBE LINE MAY HINDER INSPECTION
TECHNIQUES NECESSARY TO DETERMINE THE PRESENCE OR ABSENCE OF FATIGUE
CRACKS.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
(a) (b)-S-30R, STA NLG To STA 481SkinInspect1
S-29R, STA 960 To STA 1124.10
S-29R, STA 1124.10 To STA
1265.20
S-25R, STA 312 To STA 360
S-25R, STA 360 To STA 481
S-24R, STA 1364.10 To STA 1440
S-20R, STA 259.50 To STA 360
S-20R, STA 360 To Door Cutout
S-20R, STA 580 To STA 600K
S-20R, STA 960 To Door Cutout
S-20R, Door Cutout To STA 1164.10
S-20R, STA 1164.10 To Door Cutout
S-20R, Door Cutout To STA 1265.20
S-14R, STA 360 To Door Cutout
S-14R, Door Cutout To STA 481
S-14R, STA 1124.10 To STA
1164.10
S-14R, STA 1241 To Door Cutout
S-14R, Door Cutout To STA 1364.10
S-10R, STA 1241 To STA 1384.10
S-6R, STA 441 To STA 580
S-6L, STA 441 To STA 481
S-14L, STA 360 To STA 481
S-14L, STA 1220 To Door Cutout
S-20L, STA 259.50 To STA 360
S-20L, STA 360 To STA 441
S-20L, STA 441 To STA 600H
FIGURE 3: FUSELAGE - SKIN LAP JOINTS - INSPECTION
(SHEET 3 OF 4)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 26, 2013
A3539
68 of 110
BOEING SERVICE BULLETIN A3539
ALERTALERT

### Page 69

MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
S-20L, STA 960 To STA 1164.10
S-20L, STA 1164.10 To STA
1265.20
S-25L, STA 312 To STA 360
S-25L, STA 441 To STA 481
S-29L, STA 960 To STA 1124.10
S-29L, STA 1124.10 To STA
1265.20
(a) Do a detailed inspection of the fuselage skin for any scribe line. Use a minimum 10X magnifying lens
to aid the inspection.
(b) In areas near lap joints, scribe lines normally run parallel to the lap joint in the lower skin along the
edge of the upper skin. These scribe lines are typically within 0.25 inch of the lower edge of the upper
skin. In some cases, portions of the scribe lines may be directly adjacent to or slightly under the lower
edge of the upper skin. The ends of these scribe lines sometimes may also turn slightly away from the
lap joint.
FIGURE 3: FUSELAGE - SKIN LAP JOINTS - INSPECTION
(SHEET 4 OF 4)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 26, 2013
A3539
69 of 110
BOEING SERVICE BULLETIN A3539
ALERTALERT

### Page 70 (OCR)

BOEING SERVICE BULLETIN A3539
ALERT  ALERT
This Figure applies only to: Group 4.
1364.10  S-24R
STA  1265.20  S-23R  1303.70
STA  1241
STA
STA  1144.10
STA  1044 10  STO 1004.10  000000  STA  1024.10
STA  S-20R S-29R  LANDING  GEAR  DOOR  00000000000|  0000000000  LANDING  GEAR  DOOR  S-20L S-29L
707-300C  STA  820  S-18AR  ooo  000  S- 18AL  INSPECTION AREA  EXISTING BUTT JOINT
• SECTION 43  S-30R  00000000000000  on a
STA  600K  000000000000  STA
STA  600D
STA  600  STA
STA  580
540
SECTION 41  S-25R  2198847
FIGURE 4: FUSELAGE - SKIN LAP JOINTS - INSPECTION
(SHEET 1 OF 4)
Original Issue: April 26, 2013
PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  A3539
Work - See page 1 for details.  70 of 110

### Page 71 (OCR)

BOEING SERVICE BULLETIN A3539
ALERT  ALERT
FRAME
UPPER SKIN
STRINGER®
LOWER SKIN
TYPICAL SKI
• SCRIBE LIN
TYPICAL SKIN LAP JOINT
2198848
FIGURE 4: FUSELAGE - SKIN LAP JOINTS - INSPECTION
(SHEET 2 OF 4)
Original Issue: April 26, 2013
PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  A3539
Work - See page 1 for details.  71 of 110

### Page 72

The step numbers shown below agree with the numbers shown in the circle symbols in the figure.
CAUTION: DO NOT BLEND SCRIBE LINES. BLENDING A SCRIBE LINE MAY HINDER INSPECTION
TECHNIQUES NECESSARY TO DETERMINE THE PRESENCE OR ABSENCE OF FATIGUE
CRACKS.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
(a) (b)-S-30R, STA NLG To STA 481SkinInspect1
S-29R, STA 960 To STA 1124.10
S-29R, STA 1124.10 To STA
1265.20
S-25R, STA 312 To STA 360
S-25R, STA 360 To STA 481
S-24R, STA 1364.10 To STA 1440
S-20R, STA 259.50 To STA 360
S-20R, STA 360 To Door Cutout
S-20R, STA 580 To STA 600K
S-20R, STA 960 To Door Cutout
S-20R, Door Cutout To STA 1164.10
S-20R, STA 1164.10 To Door Cutout
S-20R, Door Cutout To STA 1265.20
S-14R, STA 360 To Door Cutout
S-14R, Door Cutout To STA 481
S-14R, STA 1124.10 To STA
1164.10
S-14R, STA 1241 To Door Cutout
S-14R, Door Cutout To STA 1364.10
S-10R, STA 1241 To STA 1384.10
S-6R, STA 441 To STA 580
S-6L, STA 441 To Door Cutout
S-14L, STA 360 To Door Cutout
S-14L, STA 1220 To Door Cutout
S-20L, STA 259.50 To STA 360
S-20L, STA 360 To STA 441
S-20L, STA 600E To STA 600H
FIGURE 4: FUSELAGE - SKIN LAP JOINTS - INSPECTION
(SHEET 3 OF 4)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 26, 2013
A3539
72 of 110
BOEING SERVICE BULLETIN A3539
ALERTALERT

### Page 73

MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
S-20L, STA 960 To STA 1164.10
S-20L, STA 1164.10 To STA
1265.20
S-25L, STA 312 To STA 360
S-25L, STA 441 To STA 481
S-29L, STA 960 To STA 1144.10
S-29L, STA 1144.10 To STA
1265.20
(a) Do a detailed inspection of the fuselage skin for any scribe line. Use a minimum 10X magnifying lens
to aid the inspection.
(b) In areas near lap joints, scribe lines normally run parallel to the lap joint in the lower skin along the
edge of the upper skin. These scribe lines are typically within 0.25 inch of the lower edge of the upper
skin. In some cases, portions of the scribe lines may be directly adjacent to or slightly under the lower
edge of the upper skin. The ends of these scribe lines sometimes may also turn slightly away from the
lap joint.
FIGURE 4: FUSELAGE - SKIN LAP JOINTS - INSPECTION
(SHEET 4 OF 4)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 26, 2013
A3539
73 of 110
BOEING SERVICE BULLETIN A3539
ALERTALERT

### Page 74 (OCR)

BOEING SERVICE BULLETIN А3539
ALERT  ALERT
This Figure applies only to: Group 1.
SECTION 46
000000  0000000000000001
STA  960
707-100B  STA  820  LANDING  GEAR  DOOR  00  LANDING  GEAR  DOOR  INSPECTION AREA  EXISTING BUTT JOINT
S-18AR  S-18AL
•SECTION 43  5.0  (TYPICAL)  STA  600K  S-30R  0000000000000000  S-30L
SECTION 41
sees is
2198849
FIGURE 5: FUSELAGE - EXTERNAL APPROVED REPAIRS - INSPECTION
(SHEET 1 OF 3)
Original Issue: April 26, 2013
PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  A3539
Work - See page 1 for details.  74 of 110

### Page 75 (OCR)

BOEING SERVICE BULLETIN А3539
ALERT  ALERT
TYPICAL
SCRIBE
LINES
• SKIN PANEL
EXTERNAL
APPROVED
REPAIR
TYPICAL EXTERNAL APPROVED REPAIR
EXTERNAL APPROVED
REPAIR
SKIN
A-A
2198862
FIGURE 5: FUSELAGE - EXTERNAL APPROVED REPAIRS - INSPECTION
(SHEET 2 OF 3)
Original Issue: April 26, 2013
Export Controlled ECCN: 9E991 - BOEING  A3539
PROPRIETARY - Copyright © Unpublished  Work - See page 1 for details.  75 of 110

### Page 76

The step numbers shown below agree with the numbers shown in the circle symbols in the figure.
CAUTION: DO NOT BLEND SCRIBE LINES. BLENDING A SCRIBE LINE MAY HINDER INSPECTION
TECHNIQUES NECESSARY TO DETERMINE THE PRESENCE OR ABSENCE OF FATIGUE
CRACKS.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
(a) (b) (c)-STA 259.50 To STA 1440 - S30R
To S30L
SkinInspect1
(a) Do a detailed inspection of the fuselage skin around external approved repairs for any scribe line. Use
a minimum 10X magnifying lens to aid the inspection.
(b) Scribe lines normally run parallel to the external approved repair along the edge of the repair. These
scribe lines are typically within 0.25 inch of the repair. In some cases, portions of the scribe lines may
be directly adjacent to or slightly under the edge of the repair.
(c) If the repair ends at a butt splice, inspect the butt splice strap at the repair area plus ten (10) inches
above and below the repair.
FIGURE 5: FUSELAGE - EXTERNAL APPROVED REPAIRS - INSPECTION
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 26, 2013
A3539
76 of 110
BOEING SERVICE BULLETIN A3539
ALERTALERT

### Page 77 (OCR)

BOEING SERVICE BULLETIN А3539
ALERT  ALERT
This Figure applies only to: Group 2.
0 -
• SECTION 46  STA  960  60000000000000000000
S-20R  LANDING  GEAR  DOOR  LANDING  GEAR  DOOR
707-300  STA  820  S-18AR  S- 18AL  INSPECTION AREA  EXISTING BUTT JOINT
•SECTION 43  - 5.0  (TYPICAL)  STA  600K  S-30R  0000000  00000000  S-30L
•0000  •
•
SECTION 41
FIGURE 6: FUSELAGE - EXTERNAL APPROVED REPAIRS - INSPECTION
(SHEET 1 OF 3)
Original Issue: April 26, 2013
Export Controlled ECCN: 9E991 - BOEING  A3539
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  77 of 110

### Page 78 (OCR)

BOEING SERVICE BULLETIN А3539
ALERT  ALERT
1)
TYPICAL
SCRIBE
LINES
A
• SKIN PANEL
EXTERNAL
APPROVED
REPAIR
TYPICAL EXTERNAL APPROVED REPAIR
A
EXTERNAL APPROVED
REPAIR
SKIN
A-A
2198852
FIGURE 6: FUSELAGE - EXTERNAL APPROVED REPAIRS - INSPECTION
(SHEET 2 OF 3)
Original Issue: April 26, 2013
PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  Work - See page 1 for details.  78 of 110  A3539

### Page 79

The step numbers shown below agree with the numbers shown in the circle symbols in the figure.
CAUTION: DO NOT BLEND SCRIBE LINES. BLENDING A SCRIBE LINE MAY HINDER INSPECTION
TECHNIQUES NECESSARY TO DETERMINE THE PRESENCE OR ABSENCE OF FATIGUE
CRACKS.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
(a) (b) (c)-STA 259.50 To STA 1440 - S30R
To S30L
SkinInspect1
(a) Do a detailed inspection of the fuselage skin around external approved repairs for any scribe line. Use
a minimum 10X magnifying lens to aid the inspection.
(b) Scribe lines normally run parallel to the external approved repair along the edge of the repair. These
scribe lines are typically within 0.25 inch of the repair. In some cases, portions of the scribe lines may
be directly adjacent to or slightly under the edge of the repair.
(c) If the repair ends at a butt splice, inspect the butt splice strap at the repair area plus ten (10) inches
above and below the repair.
FIGURE 6: FUSELAGE - EXTERNAL APPROVED REPAIRS - INSPECTION
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 26, 2013
A3539
79 of 110
BOEING SERVICE BULLETIN A3539
ALERTALERT

### Page 80 (OCR)

BOEING SERVICE BULLETIN А3539
ALERT  ALERT
This Figure applies only to: Group 3.
• SECTION 46
STA  960  0000000000000000
LANDING  GEAR  DOOR  00000000  LANDING  GEAR  DOOR
707-300B  STA  820  S-18AR  S-18AL  INSPECTION AREA  EXISTING BUTT JOINT
SECTION 43  S-30R  o c  00000000000000  S-30L
(TYPICAL)
000
•
SECTION 41  2198853
FIGURE 7: FUSELAGE - EXTERNAL APPROVED REPAIRS - INSPECTION
(SHEET 1 OF 3)
Original Issue: April 26, 2013
PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  A3539
Work - See page 1 for details.  80 of 110

### Page 81 (OCR)

BOEING SERVICE BULLETIN А3539
ALERT  ALERT
TYPICAL
SCRIBE
LINES
• SKIN PANEL
EXTERNAL
APPROVED
REPAIR
TYPICAL EXTERNAL APPROVED REPAIR
EXTERNAL APPROVED
REPAIR
SKIN
A-A
2198854
FIGURE 7: FUSELAGE - EXTERNAL APPROVED REPAIRS - INSPECTION
(SHEET 2 OF 3)
Original Issue: April 26, 2013
PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  Work - See page 1 for details.  81 of 110  A3539

### Page 82

The step numbers shown below agree with the numbers shown in the circle symbols in the figure.
CAUTION: DO NOT BLEND SCRIBE LINES. BLENDING A SCRIBE LINE MAY HINDER INSPECTION
TECHNIQUES NECESSARY TO DETERMINE THE PRESENCE OR ABSENCE OF FATIGUE
CRACKS.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
(a) (b) (c)-STA 259.50 To STA 1440 - S30R
To S30L
SkinInspect1
(a) Do a detailed inspection of the fuselage skin around external approved repairs for any scribe line. Use
a minimum 10X magnifying lens to aid the inspection.
(b) Scribe lines normally run parallel to the external approved repair along the edge of the repair. These
scribe lines are typically within 0.25 inch of the repair. In some cases, portions of the scribe lines may
be directly adjacent to or slightly under the edge of the repair.
(c) If the repair ends at a butt splice, inspect the butt splice strap at the repair area plus ten (10) inches
above and below the repair.
FIGURE 7: FUSELAGE - EXTERNAL APPROVED REPAIRS - INSPECTION
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 26, 2013
A3539
82 of 110
BOEING SERVICE BULLETIN A3539
ALERTALERT

### Page 83 (OCR)

BOEING SERVICE BULLETIN А3539
ALERT  ALERT
This Figure applies only to: Group 4.
• SECTION 46
STA  960  000000000000
LANDING  GEAR  DOOR  00000000  LANDING  GEAR  DOOR
707-300C  STA  820  S-18AR  S-18AL  INSPECTION AREA  EXISTING BUTT JOINT
•SECTION 43  - 5.0  (TYPICAL)  STA  600K  S-30R  000000  00000000000000  S-30L
SECTION 41  2198855
FIGURE 8: FUSELAGE - EXTERNAL APPROVED REPAIRS - INSPECTION
(SHEET 1 OF 3)
Original Issue: April 26, 2013
PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  A3539
Work - See page 1 for details.  83 of 110

### Page 84 (OCR)

BOEING SERVICE BULLETIN А3539
ALERT  ALERT
1)
TYPICAL
SCRIBE
LINES
A
• SKIN PANEL
EXTERNAL
APPROVED
REPAIR
TYPICAL EXTERNAL APPROVED REPAIR
A
EXTERNAL APPROVED
REPAIR
SKIN
A-A
2198856
FIGURE 8: FUSELAGE - EXTERNAL APPROVED REPAIRS - INSPECTION
(SHEET 2 OF 3)
Original Issue: April 26, 2013
PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  A3539
Work - See page 1 for details.  84 of 110

### Page 85

The step numbers shown below agree with the numbers shown in the circle symbols in the figure.
CAUTION: DO NOT BLEND SCRIBE LINES. BLENDING A SCRIBE LINE MAY HINDER INSPECTION
TECHNIQUES NECESSARY TO DETERMINE THE PRESENCE OR ABSENCE OF FATIGUE
CRACKS.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
(a) (b) (c)-STA 259.50 To STA 1440 - S30R
To S30L
SkinInspect1
(a) Do a detailed inspection of the fuselage skin around external approved repairs for any scribe line. Use
a minimum 10X magnifying lens to aid the inspection.
(b) Scribe lines normally run parallel to the external approved repair along the edge of the repair. These
scribe lines are typically within 0.25 inch of the repair. In some cases, portions of the scribe lines may
be directly adjacent to or slightly under the edge of the repair.
(c) If the repair ends at a butt splice, inspect the butt splice strap at the repair area plus ten (10) inches
above and below the repair.
FIGURE 8: FUSELAGE - EXTERNAL APPROVED REPAIRS - INSPECTION
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 26, 2013
A3539
85 of 110
BOEING SERVICE BULLETIN A3539
ALERTALERT

### Page 86 (OCR)

BOEING SERVICE BULLETIN A3539
ALERT  ALERT
This Figure applies only to: Group 1-4.
S-24R
STA  08971 0111  S-23R  1303.70
STA  1241
STA  STA  1200  1164.10
STA  1069  00000000000000000  00000000000000000  STA  1064 10  STA  1124.10
STA  1000
STA  960  S-29L
TYPICAL 707  STA  820  S-25R  S-20R  LANDING  GEAR  DOOR  LANDING  GEAR  DOOR  S-20L  INSPECTION AREA  EXISTING BUTT JOINT
S-18AR  000  S- 18AL
•SECTION 43  S-30R  Toodoo a daddan
STA  600K
STA  600
STA
STA  530  STA STA  460 520
481  • 00
SECTION 41  S-20R
2198861
FIGURE 9: FUSELAGE - EXTERNAL FEATURES - INSPECTION
(SHEET 1 OF 3)
Original Issue: April 26, 2013
PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  A3539
Work - See page 1 for details.  86 of 110

### Page 87 (OCR)

BOEING SERVICE BULLETIN A3539
ALERT  ALERT
TYPICAL SCRIBE LINES (
TYPICAL EXTERNAL FEATURE
TYPICAL
EXTERNAL
FEATURE
SKIN
A-A  2201377
FIGURE 9: FUSELAGE - EXTERNAL FEATURES - INSPECTION
(SHEET 2 OF 3)
Original Issue: April 26, 2013
PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  Work - See page 1 for details.  87 of 110  A3539

### Page 88

The step numbers shown below agree with the numbers shown in the circle symbols in the figure.
CAUTION: DO NOT BLEND SCRIBE LINES. BLENDING A SCRIBE LINE MAY HINDER INSPECTION
TECHNIQUES NECESSARY TO DETERMINE THE PRESENCE OR ABSENCE OF FATIGUE
CRACKS.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
(a) (b) (c)1S-25L To S-25R, STA 294.50 To
STA 312
Air Traffic Control /
L-Band Antenna
Inspect1
1S-30L To S-30R, STA 1010Antenna - Low
Range Radio Al-
timeter
1S-30L To S-30R, STA 1029Antenna - Low
Range Radio Al-
timeter
1S-30L To S-30R, STA 1050Antenna - Low
Range Radio Al-
timeter
1S-30L To S-30R, STA 1069Antenna - Low
Range Radio Al-
timeter Side
(a) Do a detailed inspection of the fuselage skin around the external feature for any scribe line. Use a
minimum 10X magnifying lens to aid the inspection.
(b) In areas around external features, scribe lines normally follow the periphery of the external feature.
(c) Location may vary among operators.
FIGURE 9: FUSELAGE - EXTERNAL FEATURES - INSPECTION
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 26, 2013
A3539
88 of 110
BOEING SERVICE BULLETIN A3539
ALERTALERT

### Page 89

This Figure applies only to: Group 1-4.
In each of the areas defined above, all of the inspections described in the table are necessary if scribes are
found.
The Illustration shown above is not to scale.
Initial inspections must be done with the paint removed.
Area 3 InspectionsArea 2 Inspections (h)Area 1 Inspections (h)
Skin Lap Joint locations - If any
scribe lines are found in Area 3, all
of the following inspections must be
done in Area 3. (f) Butt joint to butt
joint inspections are not required in
Area 3.
Skin Lap Joint locations - If any
scribe lines are found in Area 2, all
of the following inspections must be
done in Area 2. (f) Butt joint to butt
joint inspections are not required in
Area 2.
Skin Lap Joint locations - If any
scribe lines are found in Area 1 or
Area 2, all of the following inspec-
tions must be done in Area 1 from
butt joint to butt joint at the skin lap
joint location. (a) (g)
External Approved Repairs locations
- If any scribe lines are in Area 3, all
of the following inspections must be
done in Area 3. (f) It is not required
to inspect the entire periphery of the
external approved repair location in
Area 3.
External Approved Repairs locations
- If any scribe lines are in Area 2, all
of the following inspections must be
done in Area 2. (f) It is not required
to inspect the entire periphery of the
external approved repair location in
Area 2.
External Approved Repairs locations
- If any scribe lines are in Area 1 or
Area 2, all of the following inspec-
tions must be done in Area 1 along
the entire periphery of the external
approved repair location.
FIGURE 10: FUSELAGE - SKIN LAP JOINTS, EXTERNAL APPROVED REPAIRS, AND EXTERNAL
FEATURES - NON-DESTRUCTIVE TESTING INSPECTIONS
(SHEET 1 OF 2)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 26, 2013
A3539
89 of 110
BOEING SERVICE BULLETIN A3539
ALERTALERT

### Page 90

Area 3 InspectionsArea 2 Inspections (h)Area 1 Inspections (h)
External Feature locations - If any
scribe lines are in Area 3, all of the
following inspections must be done
in Area 3. (f) It is not required to in-
spect the entire periphery of the ex-
ternal feature location in Area 3.
External Feature locations - If any
scribe lines are in Area 2, all of the
following inspections must be done
in Area 2. (f) It is not required to in-
spect the entire periphery of the ex-
ternal feature location in Area 2.
External Feature locations - If any
scribe lines are in Area 1 or Area 2,
all of the following inspections must
be done in Area 1 along the periph-
ery of the external feature location.
High Frequency Eddy Current
(HFEC) below
High Frequency Eddy Current
(HFEC) below.
Option 1 or Option 2 below.
Surface HFEC in accordance with
707 NDT Manual Part 6, 51-00-00,
Figure 4 (b) (f)
Surface HFEC in accordance with
707 NDT Manual Part 6, 51-00-00,
Figure 4 (b) (f)
Option 1:
Ultrasonic (UT) Single Element in
accordance with 707 NDT Manual
Part 4, 53-30-05 (c) (d) or or
and Surface HFEC in accordance with
707 NDT Manual Part 6, 51-00-00,
Figure 23 (b) (f)
Surface HFEC in accordance with
707 NDT Manual Part 6, 51-00-00,
Figure 23 (b) (f)
Surface High Frequency Eddy Cur-
rent (HFEC) in accordance with 707
NDT Manual Part 6, 53-30-22 (b) or
Eddy Current Array Inspection in
accordance with 707 NDT Manual
TR 06-12, Part 6, 53-30-26 (Skin
Lap Joint locations only) (b)
or
Eddy Current Array Inspection in
accordance with 707 NDT Manual
TR 06-12, Part 6, 53-30-26 (Skin
Lap Joint locations only) (b)
Option 2:
Ultrasonic (UT) Phased Array in ac-
cordance with 707 NDT Manual Part
4, 53-30-06 (b) (e)
(a) If a door cutout breaks up a skin panel between butt joints, then do inspection from butt joint to door cutout
instead of butt joint to butt joint.
(b) After the initial inspection with the paint removed, subsequent Limited Return to Service (LRTS) inspections
using this method can be done with the paint in place. For the ultrasonic phased array inspection, paint
thickness must be less than or equal to 0.007 inch thick if paint is left in place.
(c) The paint must be removed for this inspection.
(d) The Ultrasonic (UT) Single Element inspection method can detect cracks at scribe lines up to 0.030 inch
under the edge of the overlapping skin, external approved repair, or external feature.
(e) The Ultrasonic (UT) Phased Array inspection method can detect cracks at scribe lines up to 0.030 inch
under the edge of the overlapping skin, external approved repair, or external feature and up to 0.063 inch
beyond the edge of the overlapping skin, external approved repair, or external feature.
(f) This inspection is only required locally where scribe lines exist.
(g) For the Limited Return to Service (LRTS) program, areas along skin lap joints that require butt joint to butt
joint inspections do not need to be inspected at the same time; each area may be inspected independently
at its associated LRTS inspection interval. The LRTS inspection for each area may be delayed until the
actual compliance time in which each area is located. For areas outside of the service bulletin inspection
areas, refer to Table 8 of the Compliance section of this service bulletin. This note does not apply for initial
inspections.
(h) At skin lap joints, Area 1 inspections are required from butt joint to butt joint or door opening if any scribe
line is found within Area 1 or Area 2.
FIGURE 10: FUSELAGE - SKIN LAP JOINTS, EXTERNAL APPROVED REPAIRS, AND EXTERNAL
FEATURES - NON-DESTRUCTIVE TESTING INSPECTIONS
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 26, 2013
A3539
90 of 110
BOEING SERVICE BULLETIN A3539
ALERTALERT

### Page 91 (OCR)

BOEING SERVICE BULLETIN A3539
ALERT  ALERT
This Figure applies only to: Group 5.
SECTION 46
STA  960  0000000000000
STA  820  S-20R  LANDING  GEAR  DOOR  LANDING  GEAR  DOOR  INSPECTION AREA  EXISTING BUTT JOINT  THROUGH
S-18AR  S-18AL
•SECTION 43  STA  600K  S-30R  dooc  00000000000000000000  S-30L
1000000
SECTION 41
2230660
FIGURE 11: FUSELAGE - SKIN LAP JOINTS, EXTERNAL APPROVED REPAIRS, EXTERNAL FEATURES,
SKIN BUTT JOINTS AND DECALS - INSPECTION
(SHEET 1 OF 6)
Original Issue: April 26, 2013
Export Controlled ECCN: 9E991 - BOEING  A3539
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  91 of 110

### Page 92 (OCR)

BOEING SERVICE BULLETIN A3539
ALERT  ALERT
UPPER SKIN  - LAP JOINT
FRAME
STRINGER
LOWER SKIN
1 TYPICAL SKIN  SCRIBE LINE
TYPICAL SKIN LAP JOINT
TYPICAL
SCRIBE
LINES
SKIN PANEL  SKIN PANEL
EXTERNAL  TYPICAL EXTERNAL APPROVED REPAIR
APPROVED
REPAIR
EXTERNAL
APPROVED
REPAIR
A-A  • SKIN  2230661
FIGURE 11: FUSELAGE - SKIN LAP JOINTS, EXTERNAL APPROVED REPAIRS, EXTERNAL FEATURES,
SKIN BUTT JOINTS AND DECALS - INSPECTION
(SHEET 2 OF 6)
Original Issue: April 26, 2013
PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  A3539
Work - See page 1 for details.  92 of 110

### Page 93 (OCR)

BOEING SERVICE BULLETIN А3539
ALERT  ALERT
→B
TYPICAL SCRIBE LINES 3
TYPICAL EXTERNAL FEATURE
TYPICAL
EXTERNAL
FEATURE
SKIN
B-B  2230662
FIGURE 11: FUSELAGE - SKIN LAP JOINTS, EXTERNAL APPROVED REPAIRS, EXTERNAL FEATURES,
SKIN BUTT JOINTS AND DECALS - INSPECTION
(SHEET 3 OF 6)
Original Issue: April 26, 2013
Export Controlled ECCN: 9E991 - BOEING  A3539
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  93 of 110

### Page 94 (OCR)

BOEING SERVICE BULLETIN A3539
ALERT  ALERT
•
FORWARD
SKIN PANEL
- AFT SKIN
PANEL
TYPICAL
SCRIBE
LINES
- SPLICE PLATE
TYPICAL SKIN BUTT JOINT
TYPICAL
5) SCRIBE
LINES
• SKIN PANEL
TYPICAL DECAL
L  DECAL  2230927
FIGURE 11: FUSELAGE - SKIN LAP JOINTS, EXTERNAL APPROVED REPAIRS, EXTERNAL FEATURES,
SKIN BUTT JOINTS AND DECALS - INSPECTION
(SHEET 4 OF 6)
Original Issue: April 26, 2013
Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright © Unpublished  A3539
Work - See page 1 for details.  94 of 110

### Page 95

The step numbers shown below agree with the numbers shown in the circle symbols in the figure.
CAUTION: DO NOT BLEND SCRIBE LINES. BLENDING A SCRIBE LINE MAY HINDER INSPECTION
TECHNIQUES NECESSARY TO DETERMINE THE PRESENCE OR ABSENCE OF FATIGUE
CRACKS.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
(a) (b)AllSTA 178 To STA 1440 - S30R To
S30L
Skin Lap JointsInspect1
(c) (d) (e)AllSTA 178 To STA 1440 - S30R To
S30L
External Approved
Repairs
Inspect2
(f) (g) (h)AllSTA 178 To STA 1440 - S30R To
S30L
External FeaturesInspect3
(i) (j)AllSTA 178 To STA 1440 - S30R To
S30L
Skin Butt JointsInspect4
(k) (l)AllSTA 178 To STA 1440 - S30R To
S30L
DecalsInspect5
(a) Do a detailed inspection of all skin lap joints on the fuselage skin for any scribe line. Use a minimum
10X magnifying lens to aid the inspection.
(b) In areas near lap joints, scribe lines normally run parallel to the lap joint in the lower skin along the
edge of the upper skin. These scribe lines are typically within 0.25 inch of the lower edge of the upper
skin. In some cases, portions of the scribe lines may be directly adjacent to or slightly under the lower
edge of the upper skin. The ends of these scribe lines sometimes may also turn slightly away from the
lap joint.
(c) Do a detailed inspection around all external approved repairs on the fuselage skin for any scribe line.
Use a minimum 10X magnifying lens to aid the inspection.
(d) Scribe lines normally run parallel to the external approved repair along the edge of the repair. These
scribe lines are typically within 0.25 inch of the repair. In some cases, portions of the scribe lines may
be directly adjacent to or slightly under the edge of the repair.
(e) If the repair ends at a butt splice, inspect the butt splice strap at the repair area plus ten (10) inches
above and below the repair.
(f) Do a detailed inspection around all external features on the fuselage skin for any scribe line. Use a
minimum 10X magnifying lens to aid the inspection.
(g) In areas around external features, scribe lines normally follow the periphery of the external feature.
(h) Location may vary among operators.
(i) Do a detailed inspection around all skin butt joints on the fuselage skin for any scribe line. Use a mini-
mum 10X magnifying lens to aid the inspection.
(j) Scribe lines at butt joints are normally found on the splice plate in the gap between the forward and
aft skin edges and run along the skin butt joint. In addition, scribe lines normally run parallel to the skin
butt joint. In some cases, portions of the scribe lines may be directly adjacent to the edge of the fuselage
skin.
FIGURE 11: FUSELAGE - SKIN LAP JOINTS, EXTERNAL APPROVED REPAIRS, EXTERNAL FEATURES,
SKIN BUTT JOINTS AND DECALS - INSPECTION
(SHEET 5 OF 6)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 26, 2013
A3539
95 of 110
BOEING SERVICE BULLETIN A3539
ALERTALERT

### Page 96

MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
(k) Do a detailed inspection around all decals on the fuselage skin for any scribe line. Use a minimum
10X magnifying lens to aid the inspection.
(l) In areas around decals, scribe lines normally follow the periphery of the decal.
FIGURE 11: FUSELAGE - SKIN LAP JOINTS, EXTERNAL APPROVED REPAIRS, EXTERNAL FEATURES,
SKIN BUTT JOINTS AND DECALS - INSPECTION
(SHEET 6 OF 6)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 26, 2013
A3539
96 of 110
BOEING SERVICE BULLETIN A3539
ALERTALERT

The text continues at https://openairdocs.org/service-documents/boeing/a3539/file/6a0ac8f59b88.md?from=97

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
