# Boeing Service Bulletin A3539: No revision named, from page 73

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2014-0009; AD 2014-13-11 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Service Bulletin A3539](https://openairdocs.org/service-documents/boeing/a3539.md)
- Title as filed: U.S. DOT/FAA - Service Bulletin - 707-00A3539-00
- Pages: 110
- PDF: https://openairdocs.org/files/sha256/6a/0a/6a0ac8f59b887b835591433a550daf7922c5d99625fd0f99cdd5c4f57cb35267
- Page: https://openairdocs.org/service-documents/boeing/a3539/file/6a0ac8f59b88

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 73

MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
S-20L, STA 960 To STA 1164.10
S-20L, STA 1164.10 To STA
1265.20
S-25L, STA 312 To STA 360
S-25L, STA 441 To STA 481
S-29L, STA 960 To STA 1144.10
S-29L, STA 1144.10 To STA
1265.20
(a) Do a detailed inspection of the fuselage skin for any scribe line. Use a minimum 10X magnifying lens
to aid the inspection.
(b) In areas near lap joints, scribe lines normally run parallel to the lap joint in the lower skin along the
edge of the upper skin. These scribe lines are typically within 0.25 inch of the lower edge of the upper
skin. In some cases, portions of the scribe lines may be directly adjacent to or slightly under the lower
edge of the upper skin. The ends of these scribe lines sometimes may also turn slightly away from the
lap joint.
FIGURE 4: FUSELAGE - SKIN LAP JOINTS - INSPECTION
(SHEET 4 OF 4)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 26, 2013
A3539
73 of 110
BOEING SERVICE BULLETIN A3539
ALERTALERT

### Page 74 (OCR)

BOEING SERVICE BULLETIN А3539
ALERT  ALERT
This Figure applies only to: Group 1.
SECTION 46
000000  0000000000000001
STA  960
707-100B  STA  820  LANDING  GEAR  DOOR  00  LANDING  GEAR  DOOR  INSPECTION AREA  EXISTING BUTT JOINT
S-18AR  S-18AL
•SECTION 43  5.0  (TYPICAL)  STA  600K  S-30R  0000000000000000  S-30L
SECTION 41
sees is
2198849
FIGURE 5: FUSELAGE - EXTERNAL APPROVED REPAIRS - INSPECTION
(SHEET 1 OF 3)
Original Issue: April 26, 2013
PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  A3539
Work - See page 1 for details.  74 of 110

### Page 75 (OCR)

BOEING SERVICE BULLETIN А3539
ALERT  ALERT
TYPICAL
SCRIBE
LINES
• SKIN PANEL
EXTERNAL
APPROVED
REPAIR
TYPICAL EXTERNAL APPROVED REPAIR
EXTERNAL APPROVED
REPAIR
SKIN
A-A
2198862
FIGURE 5: FUSELAGE - EXTERNAL APPROVED REPAIRS - INSPECTION
(SHEET 2 OF 3)
Original Issue: April 26, 2013
Export Controlled ECCN: 9E991 - BOEING  A3539
PROPRIETARY - Copyright © Unpublished  Work - See page 1 for details.  75 of 110

### Page 76

The step numbers shown below agree with the numbers shown in the circle symbols in the figure.
CAUTION: DO NOT BLEND SCRIBE LINES. BLENDING A SCRIBE LINE MAY HINDER INSPECTION
TECHNIQUES NECESSARY TO DETERMINE THE PRESENCE OR ABSENCE OF FATIGUE
CRACKS.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
(a) (b) (c)-STA 259.50 To STA 1440 - S30R
To S30L
SkinInspect1
(a) Do a detailed inspection of the fuselage skin around external approved repairs for any scribe line. Use
a minimum 10X magnifying lens to aid the inspection.
(b) Scribe lines normally run parallel to the external approved repair along the edge of the repair. These
scribe lines are typically within 0.25 inch of the repair. In some cases, portions of the scribe lines may
be directly adjacent to or slightly under the edge of the repair.
(c) If the repair ends at a butt splice, inspect the butt splice strap at the repair area plus ten (10) inches
above and below the repair.
FIGURE 5: FUSELAGE - EXTERNAL APPROVED REPAIRS - INSPECTION
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 26, 2013
A3539
76 of 110
BOEING SERVICE BULLETIN A3539
ALERTALERT

### Page 77 (OCR)

BOEING SERVICE BULLETIN А3539
ALERT  ALERT
This Figure applies only to: Group 2.
0 -
• SECTION 46  STA  960  60000000000000000000
S-20R  LANDING  GEAR  DOOR  LANDING  GEAR  DOOR
707-300  STA  820  S-18AR  S- 18AL  INSPECTION AREA  EXISTING BUTT JOINT
•SECTION 43  - 5.0  (TYPICAL)  STA  600K  S-30R  0000000  00000000  S-30L
•0000  •
•
SECTION 41
FIGURE 6: FUSELAGE - EXTERNAL APPROVED REPAIRS - INSPECTION
(SHEET 1 OF 3)
Original Issue: April 26, 2013
Export Controlled ECCN: 9E991 - BOEING  A3539
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  77 of 110

### Page 78 (OCR)

BOEING SERVICE BULLETIN А3539
ALERT  ALERT
1)
TYPICAL
SCRIBE
LINES
A
• SKIN PANEL
EXTERNAL
APPROVED
REPAIR
TYPICAL EXTERNAL APPROVED REPAIR
A
EXTERNAL APPROVED
REPAIR
SKIN
A-A
2198852
FIGURE 6: FUSELAGE - EXTERNAL APPROVED REPAIRS - INSPECTION
(SHEET 2 OF 3)
Original Issue: April 26, 2013
PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  Work - See page 1 for details.  78 of 110  A3539

### Page 79

The step numbers shown below agree with the numbers shown in the circle symbols in the figure.
CAUTION: DO NOT BLEND SCRIBE LINES. BLENDING A SCRIBE LINE MAY HINDER INSPECTION
TECHNIQUES NECESSARY TO DETERMINE THE PRESENCE OR ABSENCE OF FATIGUE
CRACKS.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
(a) (b) (c)-STA 259.50 To STA 1440 - S30R
To S30L
SkinInspect1
(a) Do a detailed inspection of the fuselage skin around external approved repairs for any scribe line. Use
a minimum 10X magnifying lens to aid the inspection.
(b) Scribe lines normally run parallel to the external approved repair along the edge of the repair. These
scribe lines are typically within 0.25 inch of the repair. In some cases, portions of the scribe lines may
be directly adjacent to or slightly under the edge of the repair.
(c) If the repair ends at a butt splice, inspect the butt splice strap at the repair area plus ten (10) inches
above and below the repair.
FIGURE 6: FUSELAGE - EXTERNAL APPROVED REPAIRS - INSPECTION
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 26, 2013
A3539
79 of 110
BOEING SERVICE BULLETIN A3539
ALERTALERT

### Page 80 (OCR)

BOEING SERVICE BULLETIN А3539
ALERT  ALERT
This Figure applies only to: Group 3.
• SECTION 46
STA  960  0000000000000000
LANDING  GEAR  DOOR  00000000  LANDING  GEAR  DOOR
707-300B  STA  820  S-18AR  S-18AL  INSPECTION AREA  EXISTING BUTT JOINT
SECTION 43  S-30R  o c  00000000000000  S-30L
(TYPICAL)
000
•
SECTION 41  2198853
FIGURE 7: FUSELAGE - EXTERNAL APPROVED REPAIRS - INSPECTION
(SHEET 1 OF 3)
Original Issue: April 26, 2013
PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  A3539
Work - See page 1 for details.  80 of 110

### Page 81 (OCR)

BOEING SERVICE BULLETIN А3539
ALERT  ALERT
TYPICAL
SCRIBE
LINES
• SKIN PANEL
EXTERNAL
APPROVED
REPAIR
TYPICAL EXTERNAL APPROVED REPAIR
EXTERNAL APPROVED
REPAIR
SKIN
A-A
2198854
FIGURE 7: FUSELAGE - EXTERNAL APPROVED REPAIRS - INSPECTION
(SHEET 2 OF 3)
Original Issue: April 26, 2013
PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  Work - See page 1 for details.  81 of 110  A3539

### Page 82

The step numbers shown below agree with the numbers shown in the circle symbols in the figure.
CAUTION: DO NOT BLEND SCRIBE LINES. BLENDING A SCRIBE LINE MAY HINDER INSPECTION
TECHNIQUES NECESSARY TO DETERMINE THE PRESENCE OR ABSENCE OF FATIGUE
CRACKS.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
(a) (b) (c)-STA 259.50 To STA 1440 - S30R
To S30L
SkinInspect1
(a) Do a detailed inspection of the fuselage skin around external approved repairs for any scribe line. Use
a minimum 10X magnifying lens to aid the inspection.
(b) Scribe lines normally run parallel to the external approved repair along the edge of the repair. These
scribe lines are typically within 0.25 inch of the repair. In some cases, portions of the scribe lines may
be directly adjacent to or slightly under the edge of the repair.
(c) If the repair ends at a butt splice, inspect the butt splice strap at the repair area plus ten (10) inches
above and below the repair.
FIGURE 7: FUSELAGE - EXTERNAL APPROVED REPAIRS - INSPECTION
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 26, 2013
A3539
82 of 110
BOEING SERVICE BULLETIN A3539
ALERTALERT

### Page 83 (OCR)

BOEING SERVICE BULLETIN А3539
ALERT  ALERT
This Figure applies only to: Group 4.
• SECTION 46
STA  960  000000000000
LANDING  GEAR  DOOR  00000000  LANDING  GEAR  DOOR
707-300C  STA  820  S-18AR  S-18AL  INSPECTION AREA  EXISTING BUTT JOINT
•SECTION 43  - 5.0  (TYPICAL)  STA  600K  S-30R  000000  00000000000000  S-30L
SECTION 41  2198855
FIGURE 8: FUSELAGE - EXTERNAL APPROVED REPAIRS - INSPECTION
(SHEET 1 OF 3)
Original Issue: April 26, 2013
PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  A3539
Work - See page 1 for details.  83 of 110

### Page 84 (OCR)

BOEING SERVICE BULLETIN А3539
ALERT  ALERT
1)
TYPICAL
SCRIBE
LINES
A
• SKIN PANEL
EXTERNAL
APPROVED
REPAIR
TYPICAL EXTERNAL APPROVED REPAIR
A
EXTERNAL APPROVED
REPAIR
SKIN
A-A
2198856
FIGURE 8: FUSELAGE - EXTERNAL APPROVED REPAIRS - INSPECTION
(SHEET 2 OF 3)
Original Issue: April 26, 2013
PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  A3539
Work - See page 1 for details.  84 of 110

### Page 85

The step numbers shown below agree with the numbers shown in the circle symbols in the figure.
CAUTION: DO NOT BLEND SCRIBE LINES. BLENDING A SCRIBE LINE MAY HINDER INSPECTION
TECHNIQUES NECESSARY TO DETERMINE THE PRESENCE OR ABSENCE OF FATIGUE
CRACKS.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
(a) (b) (c)-STA 259.50 To STA 1440 - S30R
To S30L
SkinInspect1
(a) Do a detailed inspection of the fuselage skin around external approved repairs for any scribe line. Use
a minimum 10X magnifying lens to aid the inspection.
(b) Scribe lines normally run parallel to the external approved repair along the edge of the repair. These
scribe lines are typically within 0.25 inch of the repair. In some cases, portions of the scribe lines may
be directly adjacent to or slightly under the edge of the repair.
(c) If the repair ends at a butt splice, inspect the butt splice strap at the repair area plus ten (10) inches
above and below the repair.
FIGURE 8: FUSELAGE - EXTERNAL APPROVED REPAIRS - INSPECTION
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 26, 2013
A3539
85 of 110
BOEING SERVICE BULLETIN A3539
ALERTALERT

### Page 86 (OCR)

BOEING SERVICE BULLETIN A3539
ALERT  ALERT
This Figure applies only to: Group 1-4.
S-24R
STA  08971 0111  S-23R  1303.70
STA  1241
STA  STA  1200  1164.10
STA  1069  00000000000000000  00000000000000000  STA  1064 10  STA  1124.10
STA  1000
STA  960  S-29L
TYPICAL 707  STA  820  S-25R  S-20R  LANDING  GEAR  DOOR  LANDING  GEAR  DOOR  S-20L  INSPECTION AREA  EXISTING BUTT JOINT
S-18AR  000  S- 18AL
•SECTION 43  S-30R  Toodoo a daddan
STA  600K
STA  600
STA
STA  530  STA STA  460 520
481  • 00
SECTION 41  S-20R
2198861
FIGURE 9: FUSELAGE - EXTERNAL FEATURES - INSPECTION
(SHEET 1 OF 3)
Original Issue: April 26, 2013
PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  A3539
Work - See page 1 for details.  86 of 110

### Page 87 (OCR)

BOEING SERVICE BULLETIN A3539
ALERT  ALERT
TYPICAL SCRIBE LINES (
TYPICAL EXTERNAL FEATURE
TYPICAL
EXTERNAL
FEATURE
SKIN
A-A  2201377
FIGURE 9: FUSELAGE - EXTERNAL FEATURES - INSPECTION
(SHEET 2 OF 3)
Original Issue: April 26, 2013
PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  Work - See page 1 for details.  87 of 110  A3539

### Page 88

The step numbers shown below agree with the numbers shown in the circle symbols in the figure.
CAUTION: DO NOT BLEND SCRIBE LINES. BLENDING A SCRIBE LINE MAY HINDER INSPECTION
TECHNIQUES NECESSARY TO DETERMINE THE PRESENCE OR ABSENCE OF FATIGUE
CRACKS.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
(a) (b) (c)1S-25L To S-25R, STA 294.50 To
STA 312
Air Traffic Control /
L-Band Antenna
Inspect1
1S-30L To S-30R, STA 1010Antenna - Low
Range Radio Al-
timeter
1S-30L To S-30R, STA 1029Antenna - Low
Range Radio Al-
timeter
1S-30L To S-30R, STA 1050Antenna - Low
Range Radio Al-
timeter
1S-30L To S-30R, STA 1069Antenna - Low
Range Radio Al-
timeter Side
(a) Do a detailed inspection of the fuselage skin around the external feature for any scribe line. Use a
minimum 10X magnifying lens to aid the inspection.
(b) In areas around external features, scribe lines normally follow the periphery of the external feature.
(c) Location may vary among operators.
FIGURE 9: FUSELAGE - EXTERNAL FEATURES - INSPECTION
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 26, 2013
A3539
88 of 110
BOEING SERVICE BULLETIN A3539
ALERTALERT

### Page 89

This Figure applies only to: Group 1-4.
In each of the areas defined above, all of the inspections described in the table are necessary if scribes are
found.
The Illustration shown above is not to scale.
Initial inspections must be done with the paint removed.
Area 3 InspectionsArea 2 Inspections (h)Area 1 Inspections (h)
Skin Lap Joint locations - If any
scribe lines are found in Area 3, all
of the following inspections must be
done in Area 3. (f) Butt joint to butt
joint inspections are not required in
Area 3.
Skin Lap Joint locations - If any
scribe lines are found in Area 2, all
of the following inspections must be
done in Area 2. (f) Butt joint to butt
joint inspections are not required in
Area 2.
Skin Lap Joint locations - If any
scribe lines are found in Area 1 or
Area 2, all of the following inspec-
tions must be done in Area 1 from
butt joint to butt joint at the skin lap
joint location. (a) (g)
External Approved Repairs locations
- If any scribe lines are in Area 3, all
of the following inspections must be
done in Area 3. (f) It is not required
to inspect the entire periphery of the
external approved repair location in
Area 3.
External Approved Repairs locations
- If any scribe lines are in Area 2, all
of the following inspections must be
done in Area 2. (f) It is not required
to inspect the entire periphery of the
external approved repair location in
Area 2.
External Approved Repairs locations
- If any scribe lines are in Area 1 or
Area 2, all of the following inspec-
tions must be done in Area 1 along
the entire periphery of the external
approved repair location.
FIGURE 10: FUSELAGE - SKIN LAP JOINTS, EXTERNAL APPROVED REPAIRS, AND EXTERNAL
FEATURES - NON-DESTRUCTIVE TESTING INSPECTIONS
(SHEET 1 OF 2)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 26, 2013
A3539
89 of 110
BOEING SERVICE BULLETIN A3539
ALERTALERT

### Page 90

Area 3 InspectionsArea 2 Inspections (h)Area 1 Inspections (h)
External Feature locations - If any
scribe lines are in Area 3, all of the
following inspections must be done
in Area 3. (f) It is not required to in-
spect the entire periphery of the ex-
ternal feature location in Area 3.
External Feature locations - If any
scribe lines are in Area 2, all of the
following inspections must be done
in Area 2. (f) It is not required to in-
spect the entire periphery of the ex-
ternal feature location in Area 2.
External Feature locations - If any
scribe lines are in Area 1 or Area 2,
all of the following inspections must
be done in Area 1 along the periph-
ery of the external feature location.
High Frequency Eddy Current
(HFEC) below
High Frequency Eddy Current
(HFEC) below.
Option 1 or Option 2 below.
Surface HFEC in accordance with
707 NDT Manual Part 6, 51-00-00,
Figure 4 (b) (f)
Surface HFEC in accordance with
707 NDT Manual Part 6, 51-00-00,
Figure 4 (b) (f)
Option 1:
Ultrasonic (UT) Single Element in
accordance with 707 NDT Manual
Part 4, 53-30-05 (c) (d) or or
and Surface HFEC in accordance with
707 NDT Manual Part 6, 51-00-00,
Figure 23 (b) (f)
Surface HFEC in accordance with
707 NDT Manual Part 6, 51-00-00,
Figure 23 (b) (f)
Surface High Frequency Eddy Cur-
rent (HFEC) in accordance with 707
NDT Manual Part 6, 53-30-22 (b) or
Eddy Current Array Inspection in
accordance with 707 NDT Manual
TR 06-12, Part 6, 53-30-26 (Skin
Lap Joint locations only) (b)
or
Eddy Current Array Inspection in
accordance with 707 NDT Manual
TR 06-12, Part 6, 53-30-26 (Skin
Lap Joint locations only) (b)
Option 2:
Ultrasonic (UT) Phased Array in ac-
cordance with 707 NDT Manual Part
4, 53-30-06 (b) (e)
(a) If a door cutout breaks up a skin panel between butt joints, then do inspection from butt joint to door cutout
instead of butt joint to butt joint.
(b) After the initial inspection with the paint removed, subsequent Limited Return to Service (LRTS) inspections
using this method can be done with the paint in place. For the ultrasonic phased array inspection, paint
thickness must be less than or equal to 0.007 inch thick if paint is left in place.
(c) The paint must be removed for this inspection.
(d) The Ultrasonic (UT) Single Element inspection method can detect cracks at scribe lines up to 0.030 inch
under the edge of the overlapping skin, external approved repair, or external feature.
(e) The Ultrasonic (UT) Phased Array inspection method can detect cracks at scribe lines up to 0.030 inch
under the edge of the overlapping skin, external approved repair, or external feature and up to 0.063 inch
beyond the edge of the overlapping skin, external approved repair, or external feature.
(f) This inspection is only required locally where scribe lines exist.
(g) For the Limited Return to Service (LRTS) program, areas along skin lap joints that require butt joint to butt
joint inspections do not need to be inspected at the same time; each area may be inspected independently
at its associated LRTS inspection interval. The LRTS inspection for each area may be delayed until the
actual compliance time in which each area is located. For areas outside of the service bulletin inspection
areas, refer to Table 8 of the Compliance section of this service bulletin. This note does not apply for initial
inspections.
(h) At skin lap joints, Area 1 inspections are required from butt joint to butt joint or door opening if any scribe
line is found within Area 1 or Area 2.
FIGURE 10: FUSELAGE - SKIN LAP JOINTS, EXTERNAL APPROVED REPAIRS, AND EXTERNAL
FEATURES - NON-DESTRUCTIVE TESTING INSPECTIONS
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 26, 2013
A3539
90 of 110
BOEING SERVICE BULLETIN A3539
ALERTALERT

### Page 91 (OCR)

BOEING SERVICE BULLETIN A3539
ALERT  ALERT
This Figure applies only to: Group 5.
SECTION 46
STA  960  0000000000000
STA  820  S-20R  LANDING  GEAR  DOOR  LANDING  GEAR  DOOR  INSPECTION AREA  EXISTING BUTT JOINT  THROUGH
S-18AR  S-18AL
•SECTION 43  STA  600K  S-30R  dooc  00000000000000000000  S-30L
1000000
SECTION 41
2230660
FIGURE 11: FUSELAGE - SKIN LAP JOINTS, EXTERNAL APPROVED REPAIRS, EXTERNAL FEATURES,
SKIN BUTT JOINTS AND DECALS - INSPECTION
(SHEET 1 OF 6)
Original Issue: April 26, 2013
Export Controlled ECCN: 9E991 - BOEING  A3539
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  91 of 110

### Page 92 (OCR)

BOEING SERVICE BULLETIN A3539
ALERT  ALERT
UPPER SKIN  - LAP JOINT
FRAME
STRINGER
LOWER SKIN
1 TYPICAL SKIN  SCRIBE LINE
TYPICAL SKIN LAP JOINT
TYPICAL
SCRIBE
LINES
SKIN PANEL  SKIN PANEL
EXTERNAL  TYPICAL EXTERNAL APPROVED REPAIR
APPROVED
REPAIR
EXTERNAL
APPROVED
REPAIR
A-A  • SKIN  2230661
FIGURE 11: FUSELAGE - SKIN LAP JOINTS, EXTERNAL APPROVED REPAIRS, EXTERNAL FEATURES,
SKIN BUTT JOINTS AND DECALS - INSPECTION
(SHEET 2 OF 6)
Original Issue: April 26, 2013
PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  A3539
Work - See page 1 for details.  92 of 110

### Page 93 (OCR)

BOEING SERVICE BULLETIN А3539
ALERT  ALERT
→B
TYPICAL SCRIBE LINES 3
TYPICAL EXTERNAL FEATURE
TYPICAL
EXTERNAL
FEATURE
SKIN
B-B  2230662
FIGURE 11: FUSELAGE - SKIN LAP JOINTS, EXTERNAL APPROVED REPAIRS, EXTERNAL FEATURES,
SKIN BUTT JOINTS AND DECALS - INSPECTION
(SHEET 3 OF 6)
Original Issue: April 26, 2013
Export Controlled ECCN: 9E991 - BOEING  A3539
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  93 of 110

### Page 94 (OCR)

BOEING SERVICE BULLETIN A3539
ALERT  ALERT
•
FORWARD
SKIN PANEL
- AFT SKIN
PANEL
TYPICAL
SCRIBE
LINES
- SPLICE PLATE
TYPICAL SKIN BUTT JOINT
TYPICAL
5) SCRIBE
LINES
• SKIN PANEL
TYPICAL DECAL
L  DECAL  2230927
FIGURE 11: FUSELAGE - SKIN LAP JOINTS, EXTERNAL APPROVED REPAIRS, EXTERNAL FEATURES,
SKIN BUTT JOINTS AND DECALS - INSPECTION
(SHEET 4 OF 6)
Original Issue: April 26, 2013
Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright © Unpublished  A3539
Work - See page 1 for details.  94 of 110

### Page 95

The step numbers shown below agree with the numbers shown in the circle symbols in the figure.
CAUTION: DO NOT BLEND SCRIBE LINES. BLENDING A SCRIBE LINE MAY HINDER INSPECTION
TECHNIQUES NECESSARY TO DETERMINE THE PRESENCE OR ABSENCE OF FATIGUE
CRACKS.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
(a) (b)AllSTA 178 To STA 1440 - S30R To
S30L
Skin Lap JointsInspect1
(c) (d) (e)AllSTA 178 To STA 1440 - S30R To
S30L
External Approved
Repairs
Inspect2
(f) (g) (h)AllSTA 178 To STA 1440 - S30R To
S30L
External FeaturesInspect3
(i) (j)AllSTA 178 To STA 1440 - S30R To
S30L
Skin Butt JointsInspect4
(k) (l)AllSTA 178 To STA 1440 - S30R To
S30L
DecalsInspect5
(a) Do a detailed inspection of all skin lap joints on the fuselage skin for any scribe line. Use a minimum
10X magnifying lens to aid the inspection.
(b) In areas near lap joints, scribe lines normally run parallel to the lap joint in the lower skin along the
edge of the upper skin. These scribe lines are typically within 0.25 inch of the lower edge of the upper
skin. In some cases, portions of the scribe lines may be directly adjacent to or slightly under the lower
edge of the upper skin. The ends of these scribe lines sometimes may also turn slightly away from the
lap joint.
(c) Do a detailed inspection around all external approved repairs on the fuselage skin for any scribe line.
Use a minimum 10X magnifying lens to aid the inspection.
(d) Scribe lines normally run parallel to the external approved repair along the edge of the repair. These
scribe lines are typically within 0.25 inch of the repair. In some cases, portions of the scribe lines may
be directly adjacent to or slightly under the edge of the repair.
(e) If the repair ends at a butt splice, inspect the butt splice strap at the repair area plus ten (10) inches
above and below the repair.
(f) Do a detailed inspection around all external features on the fuselage skin for any scribe line. Use a
minimum 10X magnifying lens to aid the inspection.
(g) In areas around external features, scribe lines normally follow the periphery of the external feature.
(h) Location may vary among operators.
(i) Do a detailed inspection around all skin butt joints on the fuselage skin for any scribe line. Use a mini-
mum 10X magnifying lens to aid the inspection.
(j) Scribe lines at butt joints are normally found on the splice plate in the gap between the forward and
aft skin edges and run along the skin butt joint. In addition, scribe lines normally run parallel to the skin
butt joint. In some cases, portions of the scribe lines may be directly adjacent to the edge of the fuselage
skin.
FIGURE 11: FUSELAGE - SKIN LAP JOINTS, EXTERNAL APPROVED REPAIRS, EXTERNAL FEATURES,
SKIN BUTT JOINTS AND DECALS - INSPECTION
(SHEET 5 OF 6)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 26, 2013
A3539
95 of 110
BOEING SERVICE BULLETIN A3539
ALERTALERT

### Page 96

MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
(k) Do a detailed inspection around all decals on the fuselage skin for any scribe line. Use a minimum
10X magnifying lens to aid the inspection.
(l) In areas around decals, scribe lines normally follow the periphery of the decal.
FIGURE 11: FUSELAGE - SKIN LAP JOINTS, EXTERNAL APPROVED REPAIRS, EXTERNAL FEATURES,
SKIN BUTT JOINTS AND DECALS - INSPECTION
(SHEET 6 OF 6)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 26, 2013
A3539
96 of 110
BOEING SERVICE BULLETIN A3539
ALERTALERT

### Page 97

1. MATERIAL AND EQUIPMENT
a. Scrapers
(1) AC Tech Scraper, TS 1275-4 (6 inch length)
Supplier: Advanced Chemistry & Technology (AC TECH)
Address: 7341 Anaconda Avenue, Garden Grove, California 92841, USA
Phone: (714) 373-2837 extension 119 or 117
Fax: (714) 373-1913
Attn: Customer Service
email: rosie.cruze@actechaero.com
NOTE: Handles are also available for these products for better comfort and control. The
handle best suited for the TS 1275-4 scraper can be purchased under the part number
SHR 0272-T from AC Tech.
(2) SEMCO Scraper: P/N 234350 (6 inch length)
Supplier: PPG Aerospace: SEMCO Division
Address: PPG Aerospace (ASC-Seattle), 14126 NE 190th Street, Woodinville, Washington
98072, USA
Phone: North America (800) 237-6649 (This connects to the closest PPG Aerospace facility
in North America. For North America and International contacts visit the web site.)
China (Suzhou) 86 512 6661 5858
Dubai UAE 971 4 883 9666
France 33 0 5 6149 4849
Germany 49 40 742 193 10
Hong Kong 852 2861 0918
South Africa 27 11 608 5656
Singapore 65 861 1119
United Kingdom 44 0 1388 770222
Web Site: www.ppg.com/prc-desoto/main
Appendix A: SEALANT REMOVAL PROCEDURE FOR EXTERIOR PRESSURIZED FUSELAGE SKIN
(SHEET 1 OF 8)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 26, 2013
A3539
97 of 110
BOEING SERVICE BULLETIN A3539
ALERTALERT

### Page 98

email: Cheryl.Chittenden@PPG.com subject=Semco Scrapers (PN-234350)
(3) Jus N Tyme Scrapers: P/N JNT 411B60 (6 inch length), P/N JNT 411B90 (9 inch length
-tapered)
Supplier: Jus N Tyme Tooling
Address: 2167 Green Canyon Road, Fallbrook, California 92028, USA
Phone: (760) 723-5985
Fax: (760) 723-5820
Contacts: Cheryl or Bob Hancock
Web Site: www.JusNTyme.com
email: Bob@JusNTyme.com
NOTE: Scraper P/N JNT 411B90 is designed for removing sealant from butt joints with a
1/4 inch or larger gap.
(4) PnJ Scrapers: P/N DFD5019, SCD5019, SFD7519, DAD5013 (5 and 9 inch lengths of varying
widths); Plastic handles: P/N SHN0272, SHW0215, SHR0272
Supplier: PnJ Machining, Inc.
Address: 2601 Inter Avenue, Puyallup, Washington 98372, USA
Phone: (253) 841-0500
Fax: (253) 840-1695
Contact: Paul Hogeboom Web site: www.pnjmachining.com
NOTE: Scraper P/N DAD5013 is designed for removing sealant from butt joints with a 1/8
inch or larger gap.
(5) Elixair Scrapers: P/N 311/03/04, 311/06/06, 311/12/04, 311/12/06, 311/24/04, 311/24/06,
311/38/04, and 311/38/06 (7.5 inch length with handle of varying widths); Skyholder Rubber
Handle: P/N 310/1; Skymill Pneumatic Scraper Sharpener: P/N 309/3; Skybag for sharpener:
P/N 309/3B
Supplier: Elixair International Limited
Address: Roman Hill Business Park, Broadmayne, Dorset DT2 8LY, United Kingdom
Phone: 44 0 1305 853019 (within the UK); 44 1305 853019 (within the USA)
Fax: 44 0 1305 852060 (within the UK); 44 1305 852060 (within the USA)
Appendix A: SEALANT REMOVAL PROCEDURE FOR EXTERIOR PRESSURIZED FUSELAGE SKIN
(SHEET 2 OF 8)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 26, 2013
A3539
98 of 110
BOEING SERVICE BULLETIN A3539
ALERTALERT

### Page 99

Contact: Len McLaughlin
Web site: www.elixair.co.uk
email: sales@elixair.com or lenmclaughlin@elixair.co.uk
NOTE: 1. Scraper P/N 311/03/06 is designed for removing sealant from butt joints
with a 3 mm or larger gap.
2. The pneumatic sharpener can be used to sharpen most plastic scrapers.
(6) Custom Components LTD Scraper: P/N 10810 (6 inch length)
Supplier: Custom Components LTD
Address: Unit 3, Feltrim Business Park, Swords Co., Dublin Ireland
Phone: 353 1 8901909
Fax: 353 1 8901907
(7) Bomatic, Inc. Scraper: P/N 1-6390-A (9 inch length - tapered)
Supplier: Bomatic, Inc.
Address: 1841 East Acacia Street, Ontario, California 91761, USA
Phone: (909) 947 3900
Fax: (909) 947 5969 Contact: Kjeld Hestehave, Cathy Macri
Web site: www.bomatic.com
NOTE: Scraper P/N 1-6390-A is designed for removing sealant from butt joints with a 1/4
inch or larger gap.
(8) General Tool & Supply Scraper: P/N ST982L-9ACE (9 inch length)
Supplier: General Tool & Supply
Address: 355 Trek Drive, Tukwila, Washington 98188, USA
Phone: (206) 762-1500
Toll Free: (800) 321-3305
Fax: (206) 767-7026
Contact: Dean Zetty
Appendix A: SEALANT REMOVAL PROCEDURE FOR EXTERIOR PRESSURIZED FUSELAGE SKIN
(SHEET 3 OF 8)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 26, 2013
A3539
99 of 110
BOEING SERVICE BULLETIN A3539
ALERTALERT

### Page 100

Web site: www.generaltool.com
email: dzetty@generaltool.com
b. Power Tools
(1) 3M SR cutter - No. 3, 0.40 inch diameter, P/N 48011-30096-2
NOTE: Any power tool that will accept the 3M SR Cutter and has a maximum speed of 850
RPM (at the cutter) can be used.
c. Solvents
(1) Methyl Ethyl Ketone (MEK), ASTM D740
(2) Methyl Propyl Ketone (MPK), BMS 11-9, Grades 1 and 2
(3) Aliphatic Naptha, TT-N-95, Type I and Type III
(4) Toluene, TT-T-548 or ASTM D362
(5) Isopropyl Alcohol TT-I-736
d. Miscellaneous
(1) Aluminum Oxide abrasive paper, 400 grit or finer
(2) Paper or wipers that meet the requirements of BSM 15-5
2. SEALANT REMOVAL NOTES:
This appendix provides procedures for removing sealant from the exterior pressurized fuselage. Using
these procedures will minimize the risk of damaging clad aluminum surfaces during sealant removal.
The main areas of concern are:
a. Lap joints
b. Butt joints (including underlying splice plates)
c. Other areas where sealant is present (i.e. wing to body fairings, windows, access doors, etc.)
Boeing recommends only approved scrapers and tools listed in Paragraph 1 of this appendix be used
for removing sealant from the exterior fuselage. Alternately, it is acceptable to use other scrapers
provided they meet the requirements of BSS7384 (Method for Evaluating Tool Materials for use on
Unpainted Clad Aluminum). Commonly used scraper materials such as Lexan polycarbonate, acrylic
(Plexiglas), Micarta fiber reinforced phenolic resins, metal, wood, and other hard plastics have been
tested and found to scratch clad aluminum.
Appendix A: SEALANT REMOVAL PROCEDURE FOR EXTERIOR PRESSURIZED FUSELAGE SKIN
(SHEET 4 OF 8)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 26, 2013
A3539
100 of 110
BOEING SERVICE BULLETIN A3539
ALERTALERT

### Page 101

3. SEALANT REMOVAL PROCESS: LAP JOINT FILLET
a. To remove the lap joint fillet, follow this procedure:
CAUTION: PLEASE NOTE THAT THERE IS A POTENTIAL FOR THE SR CUTTER TO "RUN
AWAY" AND CAUSE DAMAGE AT THE LAP JOINT AND SURROUNDING AREA.
ALSO, IF THE CUTTER CONTACTS BARE METAL BENEATH THE SEALANT,
THE CLAD ALUMINUM SKIN COULD BE DAMAGED. BEFORE USING THE 3M
SR CUTTER, OPERATORS SHOULD BE TRAINED ON PROPER USAGE OF THIS
TOOL AND SHOULD PRACTICE ON TEST PANELS OR PIECES TO PERFECT
THEIR SKILLS IN WORKING WITH THE TOOL.
(1) Remove the majority of the fillet seal at the lap joint using any of the approved scrapers listed
in Paragraph 1.a. of this appendix.
As an alternative, the 0.4 inch diameter 3M SR Cutter listed in Paragraph 1.b. of this appendix
can be used. To prevent the cutter from damaging the clad aluminum surface, do not remove
the sealant to bare metal. There should be a thin layer of sealant remaining on the surface
after removing the majority of the sealant with the 3M SR Cutter.
(2) After removing the majority of the sealant with approved scrapers or the 3M SR Cutter, remove
the remaining sealant with any of the solvents listed in Paragraph 1.c. of this appendix. An
approved scraper (Paragraph 1.a.) or wiper (Paragraph 1.a.) can be used along with the
solvent to help with the removal.
4. SEALANT REMOVAL: BUTT JOINTS AND OTHER AREAS WHERE SEALANT IS PRESENT ON
THE EXTERIOR FUSELAGE
a. To remove sealant in butt joints and other areas on the exterior fuselage, follow this procedure:
CAUTION: THE 3M SR CUTTER IS RECOMMENDED FOR REMOVING SEALANT FROM
LAP JOINTS, BUT NOT FROM BUTT JOINTS OR OTHER AREAS.
(1) Remove the bulk of the sealant using any of the approved scrapers in Paragraph 1.a. of this
appendix. Scrapers designed specifically for removing sealant from butt joints are available
(i.e. PnJ, Elixair, Bomatic, Jus N Tyme). The shape of an approved scraper can be modified
to fit a butt joint or other areas, as required. One possible modification is shown below.
Appendix A: SEALANT REMOVAL PROCEDURE FOR EXTERIOR PRESSURIZED FUSELAGE SKIN
(SHEET 5 OF 8)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 26, 2013
A3539
101 of 110
BOEING SERVICE BULLETIN A3539
ALERTALERT

### Page 102

(2) After removing the majority of the sealant with approved scrapers or the 3M SR Cutter, remove
the remaining sealant with any of the solvents listed in Paragraph 1.c. of this appendix. An
approved scraper (Paragraph 1.a.) or wiper (Paragraph 1.d.) can be used along with the
solvent to help with the removal.
5. SCRAPER MAINTENANCE
Scrapers dulled from use can be sharpened with 400 grit or finer aluminum oxide paper. Before using
a sharpened scraper, the scraper should be rubbed on paper or cheesecloth (Paragraph 1.d.2.) to
remove loose sanding particles. If an alternate method of sharpening is used, such as a metal sharpening
wheel (including the Elixair International Limited pneumatic scraper sharpener), rub the scraper on 400
grit or finer aluminum oxide paper after sharpening to remove debris, and then rub the scraper on paper
or cheesecloth to remove loose particles.
6. USE OF CHEMICAL STRIPPERS TO ASSIST IN SEALANT REMOVAL FOR SCRIBE LINE
INSPECTION
a. MATERIALS
(1) Cee-Bee E-1058, McGean-Rohco, Incorporated, Atlanta Georgia.
(2) Eldorado PR-5044, Eldorado Chemical Company, Incorporated, San Antonio Texas.
(3) Elixair - Skyrestore (Thick), Elixair International Limited, Dorchester, England.
(4) Naftosolv FN, Chemetall GMBH, Frankfurt, Germany.
(5) Skycleen 2000 Aviation Cleaner, Solutia Incorporated, Saint Louis, Missouri.
(6) Turco 5351, Henkel Corporation, Madison Heights, Michigan.
b. SEALANT REMOVAL
Use one of the following methods to remove sealant along lap and butt joints on the exterior
fuselage.
Appendix A: SEALANT REMOVAL PROCEDURE FOR EXTERIOR PRESSURIZED FUSELAGE SKIN
(SHEET 6 OF 8)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 26, 2013
A3539
102 of 110
BOEING SERVICE BULLETIN A3539
ALERTALERT

### Page 103

(1) Method 1 - Mechanical/Chemical
Remove sealant fillet with an approved scraper in accordance with Paragraph 1.a., above.
Chemically strip any sealant remaining on the surface as follows:
(a) Mask surrounding areas as necessary to prevent contact with chemical strippers. Do not
allow chemical strippers to contact substrates other than aluminum. Do not use chemical
strippers on reverse lap joints.
NOTE: Chemical strippers will soften and remove paint.
(b) Using a natural bristle brush, apply a thin coating of chemical stripper on the sealant.
CAUTION: CHEMICAL STRIPPER MAY PENETRATE INTO JOINTS IF GAPS ARE
PRESENT DUE TO MISSING FAYING SURFACE SEALANT.
1) Do not apply excessive chemical stripper. Stripper should hang and not flow.
2) Let the stripper dwell until the sealant can be easily removed by dry wiping, but do
not exceed 40 minutes dwell time.
3) Remove softened sealant with clean dry wipers (BMS 15-5 Class A). Approved
scrapers may be used to facilitate removal.
(c) After chemical stripping is complete, remove stripper by thoroughly washing with a
water-based alkaline cleaner approved for painted surfaces. Refer to SOPM 20-30-03
as an accepted procedure. Rinse off alkaline cleaner with water.
(2) Method 2 - Chemical/Mechanical/Chemical
(a) Mask surrounding areas as necessary to prevent contact with chemical strippers. Do not
allow chemical strippers to contact substrates other than aluminum.
(b) Using a natural bristle brush, apply a thin coating of chemical stripper on the sealant fillet.
(c) Let the chemical stripper dwell for a maximum of 4 hours, except use a maximum dwell
time of 2 hours if Turco 5351 is used. A thin coat of stripper may be brushed on every
hour as necessary to maintain a wet surface. Do not apply excessive stripper. Stripper
should hang and not flow.
(d) Do not apply chemical stripper to areas where the joint is exposed.
(e) Remove softened sealant with an approved scraper and clean dry wipers (BMS 15-5
Class A).
(f) Repeat steps b., c., d., and e. if necessary, but do not apply chemical stripper to areas
where the joint is exposed.
(g) If any sealant remains on the surface after removing the sealant fillet, follow the procedure
outlined in Method 1.
Appendix A: SEALANT REMOVAL PROCEDURE FOR EXTERIOR PRESSURIZED FUSELAGE SKIN
(SHEET 7 OF 8)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 26, 2013
A3539
103 of 110
BOEING SERVICE BULLETIN A3539
ALERTALERT

### Page 104

(h) After chemical stripping is complete, remove stripper by thoroughly washing with a
water-based alkaline cleaner approved for painted surfaces. Refer to SOPM 20-30-03
as an accepted procedure. Rinse off alkaline cleaner with water.
Appendix A: SEALANT REMOVAL PROCEDURE FOR EXTERIOR PRESSURIZED FUSELAGE SKIN
(SHEET 8 OF 8)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 26, 2013
A3539
104 of 110
BOEING SERVICE BULLETIN A3539
ALERTALERT

### Page 105

Boeing recommends that operators use the format that follows to report the results of the inspections in this
service bulletin to Boeing. Use of this standard format will result in a more rapid review and approval of the data.
A Return to Service Proposal will be provided by Boeing after review of the data.
INTRODUCTION
The following is a summary of the work carried out on airplane ___________ as part of a return to service
workpack.
Airplane Model:
Airplane Registration:
Airplane Variable Number:
Airplane Line Number:
Airplane Serial Number:
Airplane Total Hours / Flight Cycles:
Airplane Flight Cycles Since Scribe Line Introduction:
BACKGROUND
____________ has completed the following work on airplane ___________:
INSPECTIONS:
The following inspections were completed on airplane ___________:
Detailed Visual Inspections:
Skin Lap Joints:
Fuselage skin lap joints between STA _______ To STA _________
Findings: (Include a detailed description of any damage found, including locations, message
numbers, etc. Attach additional pages as necessary.)
Action:
-
Skin Butt Joints:
Fuselage skin butt joints between STA _______ To STA _________
Findings: (Include a detailed description of any damage found, including locations, message
numbers, etc. Attach additional pages as necessary.)
Action:
-
External Approved Repairs:
Fuselage skin around external approved repairs.
Appendix B: REPORTING TEMPLATE - AIRPLANES WITH SCRIBE LINES
(SHEET 1 OF 2)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 26, 2013
A3539
105 of 110
BOEING SERVICE BULLETIN A3539
ALERTALERT

### Page 106

Findings: (Include a detailed description of any damage found, including locations, message
numbers, etc. Attach additional pages as necessary.)
Action:
-
External Features:
Fuselage skin around external features.
Findings: (Include a detailed description of any damage found, including locations, message
numbers, etc. Attach additional pages as necessary.)
Action:
-
Decals and Fairings:
Fuselage skin around decals and fairings.
Findings: (Include a detailed description of any damage found, including locations, message
numbers, etc. Attach additional pages as necessary.)
Action:
-
Maximum Observed Scribe Line Depth:
The maximum scribe line depth for all locations (skin lap joints, skin butt joints, external
approved repairs, external features, and decals and fairings) is ______ inches.
Action:
-
NDT Inspections:
All NDT inspections for cracks at scribe line locations have been accomplished in accordance
with the Accomplishment Instructions of Service Bulletin 707-A3539.
Findings: (Include a detailed description of any damage found, including locations, message
numbers, etc. Attach additional pages as necessary.)
Action:
-
-
-
-
-
-
-
Appendix B: REPORTING TEMPLATE - AIRPLANES WITH SCRIBE LINES
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 26, 2013
A3539
106 of 110
BOEING SERVICE BULLETIN A3539
ALERTALERT

### Page 107

Table 1 - Skin Lap Joints
Depth
(inches)
Distance From Lap (Inches)Length
(inches)
Location
d_aft (c)d_min
(b)
d_fwd
(a)
LAft Body
Station
Forward Body
Station
Stringer
S-
S-
S-
S-
S-
S-
(a) d_fwd = Distance from the edge of the upper skin of the forward end of the scribe line.
(b) d_min = Minimum distance of the scribe line at any point along the entire length of the scribe
line from the edge of the upper skin.
(c) d_aft = Distance from the edge of the upper skin of the aft end of the scribe line.
Appendix C: AIRPLANE FUSELAGE SCRIBE LINE MARK SUMMARY TABLES
(SHEET 1 OF 2)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 26, 2013
A3539
107 of 110
BOEING SERVICE BULLETIN A3539
ALERTALERT

### Page 108

Table 2 - Locations other than Skin Lap Joints
Depth
(inches)
Distance From Stringer (Inch-
es)
Length
(inches)
StringerAft Body
Station
Forward Body
Station
d_aft (b)d_fwd (a)L
S-
S-
S-
S-
(a) d_fwd = Distance of the forward end of the scribe from the stringer.
(b) d_aft = Distance of the aft end of the scribe from the stringer.
Appendix C: AIRPLANE FUSELAGE SCRIBE LINE MARK SUMMARY TABLES
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 26, 2013
A3539
108 of 110
BOEING SERVICE BULLETIN A3539
ALERTALERT

### Page 109

The instructions that follow can be used to make representative samples of the kinds of scribe line marks that
may be found during the inspections specified in this service bulletin.
This design is a visual inspection aid that can be used to familiarize visual inspectors with scribe lines and assure
consistency between visual inspectors. The flag note 1 scribe line is intended to show the inspector how a scribe
line can be hidden under a lap chamfer, requiring the inspector to look at an oblique angle to the lap joint edge
to detect some scribes lines. The flag note 2 scribe line is intended to demonstrate a typical tactile scribe line.
The flag note 3 scribe line is intended to demonstrate a shallow non-tactile scribe line.
NOTE: Minimum surface roughness is 125 microinches.1.
2. Break all sharp edges.
3. Unless otherwise noted, the following dimensions and tolerances are used:
— All dimensions are in inches.
— Tolerance on linear dimensions, other than rivet or bolt edge margins, is plus or minus
0.03 inch.
— Tolerance on rivet or bolt edge margin is plus or minus 0.05 inch.
— Angular tolerance is plus or minus 2 degrees.
— Hole dimensions for standard solid rivets are given in 727 Structural Repair Manual,
Chapter 51.
1. Make part A from bare 2024-T3 aluminum, 0.040 inch thick. 0.060 inch thick bare 2024-T3 is an
acceptable substitute.
2. Make part B from bare 2024-T3 aluminum, 0.071 inch thick.
3. Fasten part B to part A with five - 5/32 inch diameter countersunk rivets. Make the countersinks in part
B.
4. Make three typical scribe line marks on part A as follows:
a. Flag Note 1: Scribe part A with the tip of a razor knife, using one to two pounds down load with
finger pressure on the knife handle. Displaced material from the scribing operation should remain
on part A. Make sure that the scribe line is under the 20 degree chamfer on the edge of part B.
Make sure the scribe line can be seen visually.
b. Flag Note 2: Scribe part A with the tip of a razor knife, using one to two pounds down load with
finger pressure on the knife handle. Displaced material from the scribing operation should remain
on part A. Make sure the scribe line is tactile (a fingernail can catch on the scribe line).
c. Flag Note 3: Scribe part A with one pass from the tip of a ball point pen, using 0.25 to 0.5 pound
down load. Make sure the scribe line is not tactile (a fingernail does not catch on the scribe line).
As an alternative to a ball point pen, use the edge of a 0.040 inch wide CRES plate, with 0.25 inch
diameter radii at the corners of the plate.
This sample can be obtained from the following vendors:
Appendix D: SCRIBE LINE SAMPLE
(SHEET 1 OF 2)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 26, 2013
A3539
109 of 110
BOEING SERVICE BULLETIN A3539
ALERTALERT

### Page 110 (OCR)

BOEING SERVICE BULLETIN A3539
ALERT  ALERT
EC/NDT  NDT ENGINEERING CORP
1020 South 344th St. Suite 214  (Olympus NDT)
Federal Way, Washington 98003 USA 421 North Quay Street
Phone: (253) 815-0797  Kennewick, Washington 99336 USA
Fax: (253) 815-0827  Phone: (509) 736-2751
Fax: (509) 735-4672
SCRIBE SAMPLE
FASTENER (TYPICAL, 5 LOCATIONS)
4.00
3.50
2.90
2.0  2.0  - 1.0-  2.0  1.0 -  2.0
(TYPICAL)  (TYPICAL)
12.0
PART B
• PART A
CHAMFER 20°1
A-A  2198885
Appendix D: SCRIBE LINE SAMPLE
(SHEET 2 OF 2)
Original Issue: April 26, 2013
Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright © Unpublished  A3539
Work - See page 1 for details.  110 of 110

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
