# Boeing Service Bulletin A3543: No revision named, from page 37

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2016-9570; AD 2017-09-04 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Service Bulletin A3543](https://openairdocs.org/service-documents/boeing/a3543.md)
- Title as filed: SB-707-00A3543-R00--
- Pages: 52
- PDF: https://openairdocs.org/files/sha256/1e/e0/1ee0b91c7b8b01f6eca20e0fdf364d1913a832123d289bef70747b36e512103c
- Page: https://openairdocs.org/service-documents/boeing/a3543/file/1ee0b91c7b8b

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 37

The step numbers shown below agree with the numbers shown in the circle symbols in the figure.
More DataQtyIdentificationNameTaskStep
(a) (b)1STA 1440Aft Pressure Bulkhead
Web
Measure1
(c)1STA 1440Aft Pressure Bulkhead
Web
Inspect2
(c)1STA 1440Aft Pressure Bulkhead
Web
Inspect3
(c)1STA 1440Aft Pressure Bulkhead
Web
Inspect4
(c)1STA 1440Aft Pressure Bulkhead
Web
Inspect5
(c)1STA 1440Aft Pressure Bulkhead
Web
Inspect6
(a) Measure the depth and width of each oil canning area to determine if the oil canning is within Zone 1 or
Zone 2 limits. Refer to view B-B and Zone 1 and Zone 2 limits Table 1.
(b) Apply the flexible metal strip to make depth and width measurements, by pressing the ends of the strip
flush to the outside surface of the web only in areas outside the oil canning outer edge. Measure the
maximum depth of the oil canning condition between the dome surface and the metal strip.
(c) Do a detailed inspection for any damage or any irregularity. Any damage can include, any sharp creases,
any gouges, any crack, any deformation to a radial stiffener, circumferential tear strap, Y-chord or terminal
fitting splice plate, or any damaged holes. Any irregularity can include, any loose or missing fasteners,
any pressure leakage, any fasteners within 1.0 inch of any oil canning location or any oil canning location
within 2.0 inch inches of any other oil canning location.
FIGURE 2: STA 1440 AFT PRESSURE BULKHEAD WEB - OIL CANNING ZONE DETERMINATION AND
DETAILED INSPECTION
(SHEET 7 OF 7)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 15, 2016
A3543
37 of 52
BOEING SERVICE BULLETIN A3543
ALERTALERT

### Page 38 (OCR)

BOEING SERVICE BULLETIN А3543
ALERT  ALERT
CIRCUMFERENTIAL
TEAR STRAPS
WEB LAP SPLICE
RADIAL
STIFFENERS
AFT PRESSURE
INSPECTION AREA  VIEW LOOKING FORWARD  BULKHEAD WEB  2506484
A-A
FIGURE 3: STA 1440 AFT PRESSURE BULKHEAD WEB - DETAILED INSPECTION AND EDDY CURRENT
INSPECTION
(SHEET 1 OF 4)
Original Issue: September 15, 2016
PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  A3543
Work - See page 1 for details.  38 of 52

### Page 39 (OCR)

BOEING SERVICE BULLETIN А3543
ALERT  ALERT
RADIAL STIFFENER  OIL CANNING
CIRCUMFERENTIAL
TEAR STRAP
RADIAL STIFFENER
TYPICAL OIL
CANNING
TYPICAL WEB BAY AREA (5
WEB LAP SPLICE
INSPECTION AREA  • RADIAL STIFFENER
TYPICAL OIL CANNING
OUTER EDGE
ORIGINAL
CONTOUR  AFT PRESSURE
BULKHEAD WEB
RADIAL
STIFFENER
TYPICAL OIL
CANNING
WEB LAP
SPLICE
INSPECTION AREA  B-B  2506490
FIGURE 3: STA 1440 AFT PRESSURE BULKHEAD WEB - DETAILED INSPECTION AND EDDY CURRENT
INSPECTION
(SHEET 2 OF 4)
Original Issue: September 15, 2016
Export Controlled ECCN: 9E991 - BOEING  A3543
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  39 of 52

### Page 40

The step numbers shown below agree with the numbers shown in the circle symbols in the figure.
More DataQtyIdentificationNameTaskStep
(a)1STA 1440Aft Pressure Bulkhead
Web
Inspect1
(b)1STA 1440Aft Pressure Bulkhead
Web
Inspect2
(c)1STA 1440Aft Pressure Bulkhead
Web
Inspect3
(d)1STA 1440Aft Pressure Bulkhead
Web
Inspect4
(e)1STA 1440Aft Pressure Bulkhead
Web
Inspect5
(f)1STA 1440Aft Pressure Bulkhead
Web
Inspect6
(a) Do a detailed inspection for any crack on the STA 1440 aft pressure bulkhead web.
(b) Do a surface HFEC inspection for any crack of the web, from the aft side along each oil canning outer
edge in accordance with 707, 720 NDT Manual Part 6, 51-00-00, Figure 4 or Figure 23.
(c) Do a LFEC inspection for any crack of the forward web lap splice hidden fastener rows, from the aft side
of the aft pressure bulkhead web at all fastener locations common to the outer edge of the web bay area
in which the oil canning was found in accordance with 707, 720 NDT Manual Part 6, 53-10-07, Figure 18.
FIGURE 3: STA 1440 AFT PRESSURE BULKHEAD WEB - DETAILED INSPECTION AND EDDY CURRENT
INSPECTION
(SHEET 3 OF 4)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 15, 2016
A3543
40 of 52
BOEING SERVICE BULLETIN A3543
ALERTALERT

### Page 41

More DataQtyIdentificationNameTaskStep
(d) Do a LFEC inspection for any crack of the web hidden underneath the circumferential tear straps, from
the aft side of the aft pressure bulkhead web at all fastener locations common to the perimeter of the web
bay area in which the oil canning was found in accordance with 707, 720 NDT Manual Part 6, 53-10-07,
Figure 18.
(e) Do a surface HFEC inspection for any crack of the web common to the radial stiffener, from the aft side
of the aft pressure bulkhead web at all fastener locations common to the outer edge of the web bay area
in which the oil canning was found in accordance with 707, 720 NDT Manual Part 6, 51-00-00, Figure 4
or Figure 23. Make sure to inspect 360 degrees around fasteners.
(f) Do a surface HFEC inspection for any crack of the web common to a web lap splice, from the aft side of
the aft pressure bulkhead web at all fastener locations common to the outer edge of the web bay area in
which the oil canning was found in accordance with 707, 720 NDT Manual Part 6, 51-00-00, Figure 4 or
Figure 23. Make sure to inspect 360 degrees around fasteners.
FIGURE 3: STA 1440 AFT PRESSURE BULKHEAD WEB - DETAILED INSPECTION AND EDDY CURRENT
INSPECTION
(SHEET 4 OF 4)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 15, 2016
A3543
41 of 52
BOEING SERVICE BULLETIN A3543
ALERTALERT

### Page 42 (OCR)

BOEING SERVICE BULLETIN А3543
ALERT  ALERT
Y CHORD
CIRCUMFERENTIAL
TEAR STRAPS
WEB LAP SPLICE
RADIAL
STIFFENERS
AFT PRESSURE
VIEW LOOKING FORWARD  BULKHEAD WEB
INSPECTION AREA
A-A
FIGURE 4: STA 1440 AFT PRESSURE BULKHEAD WEB - Y-CHORD - DETAILED INSPECTION AND EDDY
CURRENT INSPECTION
(SHEET 1 OF 5)
Original Issue: September 15, 2016
PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  A3543
Work - See page 1 for details.  42 of 52

### Page 43 (OCR)

BOEING SERVICE BULLETIN А3543
ALERT  ALERT
RADIAL STIFFENER
C
TYPICAL OIL
CIRCUMFERENTIAL  CANNING
TEAR STRAP
Y CHORD
6) TYPICAL WEB
RADIAL STIFFENER'  BAY AREA
WEB LAP SPLICE
INSPECTION AREA
RADIAL STIFFENER
STA
1440
SKIN
Y CHORD
AFT PRESSURE
BULKHEAD WEB
FWD
.00
/ INSPECTION AREA  B-B  2518712
FIGURE 4: STA 1440 AFT PRESSURE BULKHEAD WEB - Y-CHORD - DETAILED INSPECTION AND EDDY
CURRENT INSPECTION
(SHEET 2 OF 5)
Original Issue: September 15, 2016
Export Controlled ECCN: 9E991 - BOEING  A3543
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  43 of 52

### Page 44 (OCR)

BOEING SERVICE BULLETIN А3543
ALERT  ALERT
) TYPICAL OIL CANNING
OUTER EDGE
ORIGINAL
CONTOUR  AFT PRESSURE
BULKHEAD WEB
RADIAL
STIFFENER
TYPICAL OIL
CANNING
WEB LAP
SPLICE
C-C
INSPECTION AREA
3) TYPICAL OIL CANNING
OUTER EDGE
ORIGINAL
CONTOUR  CIRCUMFERENTIAL
TEAR STRAP
AFT PRESSURE  TYPICAL OIL
BULKHEAD WEB  CANNING
D-D
INSPECTION AREA  2508283
FIGURE 4: STA 1440 AFT PRESSURE BULKHEAD WEB - Y-CHORD - DETAILED INSPECTION AND EDDY
CURRENT INSPECTION
(SHEET 3 OF 5)
Original Issue: September 15, 2016
PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  A3543
Work - See page 1 for details.  44 of 52

### Page 45

The step numbers shown below agree with the numbers shown in the circle symbols in the figure.
More DataQtyIdentificationNameTaskStep
(a) (b) (c)1STA 1440Aft Pressure Bulkhead
Web
Inspect1
(d)1STA 1440Aft Pressure Bulkhead
Web
Inspect2
(e)1STA 1440Aft Pressure Bulkhead
Web
Inspect3
(f)1STA 1440Aft Pressure Bulkhead
Web
Inspect4
(g)1STA 1440Aft Pressure Bulkhead
Web
Inspect5
(h)1STA 1440Aft Pressure Bulkhead
Web
Inspect6
(i)1STA 1440Aft Pressure Bulkhead
Web
Inspect7
(a) Do a surface High Frequency Eddy Current (HFEC) inspection for any crack at the aft fastener row from
the forward side of the bulkhead in accordance with 707, 720 NDT Manual Part 6, 51-00-00, Figure 4 or
23. Make sure to inspect 360 degrees around the fastener. Do this inspection except where a radial stiff-
ener overlaps the Y-chord at the perimeter of the web at the fastener locations or where production doublers
overlap the web.
(b) Where a radial stiffener overlaps the Y-chord at the perimeter of the web at the fastener location, do a
surface HFEC inspection for any crack of the web, along the edge of the radial stiffener adjacent to the
fastener locations in accordance with 707, 720 NDT Manual Part 6, 51-00-00, Figure 4 or 23. Make sure
to inspect the web up to 1.0 inch on each side of the fastener row.
(c) Where production doublers overlap the web, do a surface HFEC inspection for any crack of the web,
along the outer edge fastener row of the doubler in accordance with 707, 720 NDT Manual Part 6, 51-00-
00, Figure 4 or Figure 23.
(d) Do a detailed inspection for any crack of the web, from the aft side along each oil canning outer edge.
(e) Do a surface HFEC inspection for any crack of the web, from the aft side along each oil canning outer
edge in accordance with 707, 720 NDT Manual Part 6, 51-00-00, Figure 4 or Figure 23.
(f) Do a LFEC inspection for any crack of the forward web lap splice hidden fastener rows, from the aft side
of the aft pressure bulkhead web at all fastener locations common to the outer edge of the web bay area
in which the oil canning was found in accordance with 707, 720 NDT Manual Part 6, 53-10-07, Figure 18.
(g) Do a HFEC inspection for any crack of the web underneath the circumferential tear straps, from the forward
side of the aft pressure bulkhead web at all fastener locations common to the perimeter of the web bay
area in which the oil canning was found in accordance with 707, 720 NDT Manual Part 6, 51-00-00, Figure
4 or Figure 23.
FIGURE 4: STA 1440 AFT PRESSURE BULKHEAD WEB - Y-CHORD - DETAILED INSPECTION AND EDDY
CURRENT INSPECTION
(SHEET 4 OF 5)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 15, 2016
A3543
45 of 52
BOEING SERVICE BULLETIN A3543
ALERTALERT

### Page 46

More DataQtyIdentificationNameTaskStep
(h) Do a surface HFEC inspection for any crack of the web common to the radial stiffener, from the aft side
of the aft pressure bulkhead web at all fastener locations common to the outer edge of the web bay area
in which the oil canning was found in accordance with 707, 720 NDT Manual Part 6, 51-00-00, Figure 4
or Figure 23. Make sure to inspect 360 degrees around fasteners.
(i) Do a surface HFEC inspection for any crack of the web common to a web lap splice, from the aft side of
the aft pressure bulkhead web at all fastener locations common to the outer edge of the web bay area in
which the oil canning was found in accordance with 707, 720 NDT Manual Part 6, 51-00-00, Figure 4 or
Figure 23. Make sure to inspect 360 degrees around fasteners.
FIGURE 4: STA 1440 AFT PRESSURE BULKHEAD WEB - Y-CHORD - DETAILED INSPECTION AND EDDY
CURRENT INSPECTION
(SHEET 5 OF 5)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 15, 2016
A3543
46 of 52
BOEING SERVICE BULLETIN A3543
ALERTALERT

### Page 47 (OCR)

BOEING SERVICE BULLETIN A3543
ALERT  ALERT
1 TYPICAL OIL CANNING
RADIAL STIFFENER
(TYPICAL)
CIRCUMFERENTIAL
TEAR STRAPS
AFT PRESSURE
BULKHEAD WEB
INSPECTION AREA  TYPICAL AFT PRESSURE BULKHEAD  (VIEW LOOKING AFT)  2508598
A-A
FIGURE 5: STA 1440 AFT PRESSURE BULKHEAD WEB - HIGH FREQUENCY EDDY CURRENT (HFEC)
INSPECTION
(SHEET 1 OF 2)
Original Issue: September 15, 2016
Export Controlled ECCN: 9E991 - BOEING  A3543
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  47 of 52

### Page 48

The step numbers shown below agree with the numbers shown in the circle symbols in the figure.
More DataQtyIdentificationNameTaskStep
(a) (b)1STA 1440Aft Pressure Bulkhead
Web
Inspect1
(a) Do a surface High Frequency Eddy Current (HFEC) inspection from the forward side of the affected location
for the crack location, length and orientation in accordance with 707, 720 NDT Manual Part 6, 51-00-00,
Figure 4 or Figure 23.
(b) If access is not available to do a surface HFEC inspection, then remove the fasteners at the affected lo-
cation and do an Open Hole Eddy Current inspection of the web at the affected location to find the crack
location and orientation in accordance with 707, 720 NDT Manual Part 6, 51-00-00, Figure 16.
FIGURE 5: STA 1440 AFT PRESSURE BULKHEAD WEB - HIGH FREQUENCY EDDY CURRENT (HFEC)
INSPECTION
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 15, 2016
A3543
48 of 52
BOEING SERVICE BULLETIN A3543
ALERTALERT

### Page 49

Logic diagrams are provided as an aid only. Information contained in Paragraph 1.E., Compliance is the primary
source for compliance times. Information contained in Paragraph 3.B., Work Instructions is the primary source
for tasks required for compliance.
1. The table below gives the description for the parts and conditions called out in the logic diagrams.
DescriptionTitle
DETAILED INSPECTION OF THE STA 1440 AFT PRESSURE BULKHEAD
WEB.
PART 2
OIL CANNING ZONE DETERMINATION AND DETAILED INSPECTION.PART 3
DETAILED INSPECTION AND EDDY CURRENT INSPECTION.PART 4
HIGH FREQUENCY EDDY CURRENT (HFEC) INSPECTION.PART 5
NO OIL CANNING FOUND.CONDITION 1
ANY OIL CANNING FOUND.CONDITION 2
ANY OIL CANNING FOUND WITHIN ZONE 1 LIMITS AND NO CRACK
FOUND.
CONDITION 2.1
ANY OIL CANNING FOUND WITH ANY DAMAGE OR ANY IRREGULARITY.CONDITION 2.2
ANY OIL CANNING FOUND WITHIN ZONE 2 LIMITS AND NO CRACK
FOUND.
CONDITION 2.3
ANY OIL CANNING FOUND WITH ANY CRACK FOUND.CONDITION 2.4
2. The table below gives the description for the flag notes called out in the logic diagram.
DescriptionFlag Note Letter
Any damage can include, any sharp creases, any gouges, any crack, any
deformation to a radial stiffener, circumferential tear strap, Y-chord or terminal
fitting splice plate, or any damaged holes.
(a)
Any irregularity can include, any loose or missing fasteners, any pressure
leakage, any fasteners within 1.0 inch of any oil canning location or any oil
canning location within 2.0 inch inches of any other oil canning location.
APPENDIX A: TABLE 1: STA 1440 AFT PRESSURE BULKHEAD WEB INSPECTION FOR OIL CANNING
(SHEET 1 OF 4)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 15, 2016
A3543
49 of 52
BOEING SERVICE BULLETIN A3543
ALERTALERT

### Page 50 (OCR)

BOEING SERVICE BULLETIN A3543
ALERT  ALERT
CONDITION 2
(ACTION 2):
DO PART 4
WHICHEVER OCCURS LATER
WITHIN 1,200 FLIGHT
BEFORE 15,000 TOTAL  CYCLES AFTER THE  ORIGINAL ISSUE DATE
FLIGHT CYCLES  OF THIS SERVICE
BULLETIN
DO PART 2
CONDITION 1  CONDITION 2
NOT TO EXCEED 6,000  BEFORE FURTHER
FLIGHT CYCLES  FLIGHT
REPEAT  CONDITION 2
PART 2  (ACTION 1):
DO PART 3 (a)
C
2521696
APPENDIX A: TABLE 1: STA 1440 AFT PRESSURE BULKHEAD WEB INSPECTION FOR OIL CANNING
(SHEET 2 OF 4)
Original Issue: September 15, 2016
Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright © Unpublished  A3543
Work - See page 1 for details.  50 of 52

### Page 51 (OCR)

BOEING SERVICE BULLETIN А3543
ALERT  ALERT
CONDITION 2
(ACTION2):
DO PART 4
CONDITION 2.1  CONDITION 2.2
(a)
NOT TO EXCEED 1,200  BEFORE FURTHER  BEFORE FURTHER
FLIGHT CYCLES  FLIGHT  FLIGHT
OPTION 1 (ACTION 1):  OPTION 2 (ACTION 1):  CONDITION 2.2 (ACTION 1)
REPEAT PART 4  CONTACT THE  CONTACT THE
BOEING COMPANY  BOEING COMPANY
FOR REPAIR  FOR REPAIR
INSTRUCTIONS  INSTRUCTIONS
AND DO THE  AND DO THE
WITHIN 12,000  REPAIR  REPAIR
FLIGHT CYCLES
AFTER THE
OIL CANNING
CONDITION WAS  NOT TO EXCEED 6,000  NOT TO EXCEED 6,000
FOUND  FLIGHT CYCLES  FLIGHT CYCLES
OPTION 1 (ACTION 2):  BOEING COMPANY  CONTACT THE  OPTION 2 (ACTION 2):  REPEAT PART 2  CONDITION 2.2  (ACTION 2):
REPEAT PART 2
FOR REPAIR
INSTRUCTIONS AND
DO THE REPAIR
NOT TO EXCEED 6,000
FLIGHT CYCLES
OPTION 1 (ACTION 3):
REPEAT PART 2
2521697
APPENDIX A: TABLE 1: STA 1440 AFT PRESSURE BULKHEAD WEB INSPECTION FOR OIL CANNING
(SHEET 3 OF 4)
Original Issue: September 15, 2016
Export Controlled ECCN: 9E991 - BOEING  A3543
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  51 of 52

### Page 52 (OCR)

BOEING SERVICE BULLETIN А3543
ALERT  ALERT
C
CONDITION 2.3  CONDITION 2.4
BEFORE FURTHER  BEFORE FURTHER
FLIGHT  FLIGHT
CONDITION 2.3 (ACTION 1):  CONDITION 2.4
CONTACT THE  (ACTION 1):
BOEING COMPANY  DO PART 5
FOR REPAIR
INSTRUCTIONS
AND DO THE
REPAIR
CONDITION 2.4
NOT TO EXCEED 6,000  (ACTION 2):
FLIGHT CYCLES  CONTACT THE
BOEING COMPANY
FOR REPAIR
INSTRUCTIONS AND
CONDITION 2.3  DO THE REPAIR
(ACTION 2):
REPEAT PART 2
NOT TO EXCEED 6,000
FLIGHT CYCLES
CONDITION 2.4
(ACTION 3):
REPEAT PART 2
2521695
APPENDIX A: TABLE 1: STA 1440 AFT PRESSURE BULKHEAD WEB INSPECTION FOR OIL CANNING
(SHEET 4 OF 4)
Original Issue: September 15, 2016a
Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright @ Unpublished  A3543
Work - See page 1 for details.  52 of 52

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
