# Boeing Service Bulletin DC10-28-244: No revision named

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2010-0553; AD 2010-20-13 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Service Bulletin DC10-28-244](https://openairdocs.org/service-documents/boeing/dc10-28-244.md)
- Title as filed: Boeing - Service Bulletin
- Pages: 130
- PDF: https://openairdocs.org/files/sha256/9d/14/9d143a7b7336cbfcdc5b9a3771549d142df4802d77c0cddc922086e72088cdb1
- Page: https://openairdocs.org/service-documents/boeing/dc10-28-244/file/9d143a7b7336

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Commercial 
Airplanes
DC10
Service Bulletin
Number: DC10-28-244
Original Issue: February 25, 2010
ATA System: 2811
SUBJECT: FUEL - Integral Fuel Tanks - Inspection and Replacement of Wire Shielding above
Center Upper Auxiliary Fuel Tank
Export of this technology is controlled under the United States Export Administration Regulations (EAR) (15
CFR 730-774). An export license may be required before it is used for development, production or use by foreign
persons from specific countries. The controller of this data has the individual responsibility to abide by all export
laws.
9E991ECCN:
BOEING PROPRIETARY, CONFIDENTIAL, AND/OR TRADE SECRET
Copyright © 2010 The Boeing Company
Unpublished Work - All Rights Reserved
Boeing claims copyright in each page of this document only to the extent that the page contains copyrightable
subject matter. Boeing also claims copyright in this document as a compilation and/or collective work.
This document includes proprietary information owned by The Boeing Company and/or one or more third parties.
Treatment of the document and the information it contains is governed by contract with Boeing. For more
information, contact The Boeing Company, P.O. Box 3707, Seattle, Washington 98124.
Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner,
BBJ, DC-8, DC-9, DC-10, KC-10, KDC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8A, Poseidon and the
Boeing livery are all trademarks owned by The Boeing Company; and no trademark license is granted in
connection with this document unless provided in writing by Boeing.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 25, 2010
DC10-28-244
1 of 130
2.0

### Page 2

BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 25, 2010
DC10-28-244
2 of 130
BOEING SERVICE BULLETIN DC10-28-244
BLANK PAGE

### Page 3

Table of Contents
Summary ...................................................... 5
1. PLANNING INFORMATION ........................................ 9
A. Effectivity ................................................ 9
1. Airplanes ............................................. 9
2. Spares Affected ........................................ 1 3
B. Concurrent Requirements ...................................... 1 3
C. Reason ................................................ 1 4
D. Description .............................................. 1 4
E. Compliance .............................................. 1 5
F. Approval ............................................... 1 5
G. Manpower .............................................. 1 6
H. Weight and Balance Changes .................................... 1 7
I. Electrical Load Data ......................................... 1 8
J. References .............................................. 1 8
1. Existing Data: ......................................... 1 8
2. Data supplied with this Service Bulletin: ........................... 1 8
3. Installation Drawings Used in the Preparation of this Service Bulletin: ........... 1 8
K. Publications Affected ........................................ 1 8
L. Interchangeability and Intermixability of Parts ........................... 1 9
2. MATERIAL INFORMATION ........................................ 2 1
A. Material - Price and Availability ................................... 2 1
B. Industry Support Information .................................... 2 1
C. Parts Necessary For Each Airplane ................................. 2 1
1. Kits/Parts: ........................................... 2 1
2. Parts and Materials Supplied by the Operator: ........................ 2 6
3. Parts Modified and Reidentified: ............................... 2 6
4. Parts Removed and Not Replaced: .............................. 2 6
D. Parts Necessary to Change Spares ................................. 2 7
E. Special Tooling - Price and Availability ............................... 2 7
F. Special Tooling Necessary to do this Service Bulletin ....................... 2 7
3. ACCOMPLISHMENT INSTRUCTIONS .................................. 2 9
A. GENERAL INFORMATION ..................................... 2 9
B. WORK INSTRUCTIONS ....................................... 3 2
FIGURE 1: WIRES ABOVE AUXILIARY FUEL TANK LEFT SIDE - FLOOR BEAM CLAMPS - REMOVAL
[Group 1] ............................................ 4 0
FIGURE 2: WIRES ABOVE AUXILIARY FUEL TANK LEFT SIDE - BARRIER/SHIELD SLEEVING -
INSTALLATION [Group 1] ................................... 4 6
FIGURE 3: WIRES ABOVE AUXILIARY FUEL TANK LEFT SIDE - CLAMPS AND EXTRUDED CHANNEL
- INSTALLATION [Group 1] .................................. 4 9
FIGURE 4: WIRES ABOVE AUXILIARY FUEL TANK RIGHT SIDE - FLOOR BEAM CLAMPS - REMOVAL
[Group 1-2, 4] .......................................... 5 5
FIGURE 5: WIRES ABOVE AUXILIARY FUEL TANK RIGHT SIDE - BARRIER/SHIELD SLEEVING -
INSTALLATION [Group 1-2, 4] ................................ 6 0
FIGURE 6: WIRES ABOVE AUXILIARY FUEL TANK RIGHT SIDE - CLAMPS AND EXTRUDED CHANNEL
- INSTALLATION [Group 1-2, 4] ................................ 6 3
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 25, 2010
DC10-28-244
3 of 130
BOEING SERVICE BULLETIN DC10-28-244

### Page 4

FIGURE 7: WIRES ABOVE AUXILIARY FUEL TANK LEFT SIDE - FLOOR BEAM CLAMPS - REMOVAL
[Group 2] ............................................ 6 8
FIGURE 8: WIRES ABOVE AUXILIARY FUEL TANK LEFT SIDE - BARRIER/SHIELD SLEEVING -
INSTALLATION [Group 2] ................................... 7 4
FIGURE 9: WIRES ABOVE AUXILIARY FUEL TANK LEFT SIDE - CLAMPS AND EXTRUDED CHANNEL
- INSTALLATION [Group 2] .................................. 7 7
FIGURE 10: FORWARD CARGO D SECTION RIGHT SIDE - BARRIER/SHIELD SLEEVING - INSTALLATION
[Group 2] ............................................ 8 4
FIGURE 11: WIRES ABOVE AUXILIARY FUEL TANK LEFT SIDE - FLOOR BEAM CLAMPS - REMOVAL
[Group 3] ............................................ 8 6
FIGURE 12: WIRES ABOVE AUXILIARY FUEL TANK LEFT SIDE - BARRIER/SHIELD SLEEVING -
INSTALLATION [Group 3] ................................... 9 2
FIGURE 13: WIRES ABOVE AUXILIARY FUEL TANK LEFT SIDE - CLAMPS AND EXTRUDED CHANNEL
- INSTALLATION [Group 3] .................................. 9 5
FIGURE 14: WIRES ABOVE AUXILIARY FUEL TANK RIGHT SIDE - FLOOR BEAM CLAMPS - REMOVAL
[Group 3] ............................................ 1 0 1
FIGURE 15: WIRES ABOVE AUXILIARY FUEL TANK RIGHT SIDE - BARRIER/SHIELD SLEEVING -
INSTALLATION [Group 3] .................................. 1 0 7
FIGURE 16: WIRES ABOVE AUXILIARY FUEL TANK RIGHT SIDE - CLAMPS AND EXTRUDED CHANNEL
- INSTALLATION [Group 3] .................................. 1 1 0
FIGURE 17: WIRES ABOVE AUXILIARY FUEL TANK LEFT SIDE - FLOOR BEAM CLAMPS - REMOVAL
[Group 4] ............................................ 1 1 6
FIGURE 18: WIRES ABOVE AUXILIARY FUEL TANK LEFT SIDE - BARRIER/SHIELD SLEEVING -
INSTALLATION [Group 4] .................................. 1 2 1
FIGURE 19: WIRES ABOVE AUXILIARY FUEL TANK LEFT SIDE - CLAMPS AND EXTRUDED CHANNEL
- INSTALLATION [Group 4] .................................. 1 2 4
APPENDIX A: TYPICAL CLAMP ATTACHMENTS ............................. 1 3 0
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 25, 2010
DC10-28-244
4 of 130
BOEING SERVICE BULLETIN DC10-28-244

### Page 5

Commercial 
Airplanes
DC10
Service Bulletin
SummaryNumber: DC10-28-244Original Issue: February 25, 2010
ATA System: 2811
SUBJECT: FUEL - Integral Fuel Tanks - Inspection and Replacement of Wire Shielding above
Center Upper Auxiliary Fuel Tank
CONCURRENT REQUIREMENTS
None.
BACKGROUND
Boeing Special Federal Aviation Regulations (SFAR) 88 engineering investigations have determined that wires
routed above the center upper auxiliary fuel tank are in close proximity to the upper surface of the tank. In
addition, some wire harness mounts may have loosened, allowing the wires to contact the tank. This condition
can cause wire damage or chafing that could lead to possible arcing and sparking on the fuel tank upper surface.
Inspection will determine the condition of the wires. Installation of nonmetallic barrier/shield sleeving, new clamps,
and new extruded channels to support the wires will minimize the possibility of wires contacting the fuel tank
upper surface. If not corrected, wires in contact with the fuel tank could become damaged, and the resulting
possible arcing and sparking could lead to burn-through of the upper surface of the fuel tank and potentially
result in an explosion.
This service bulletin resulted from the safety assessments conducted by Boeing under Special Federal Aviation
Regulations (SFAR) 88, Fuel Tank System Fault Tolerance Evaluation Requirements.
ACTION
This service bulletin provides instructions to do as follows:
1. Does a General Visual Inspection of the wire bundles to determine if wires touch the upper surface of the
center upper auxiliary fuel tank and marks those locations.
2. Does a Detailed Inspection of the wires routed above the center upper auxiliary fuel tank for splices and
other damage (such as wire chafing, arcing, and broken insulation) to wire bundles and does corrective
action as necessary.
3. Does a Detailed Inspection of the upper surface of the center upper auxiliary fuel tank for damage to the
fuel barrier seal and does corrective action as necessary.
4. Installs nonmetallic barrier/shield sleeving to the wire harnesses, new clamps, new attaching hardware,
and new extruded channels to raise the wire harnesses off the upper surface of the center upper auxiliary
fuel tank.
This service bulletin assumes that the area above the center upper auxiliary fuel tank is open and access is
available to all the floor beams for maintenance.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 25, 2010
DC10-28-244
5 of 130

### Page 6

EFFECTIVITY
DC-10-30, DC-10-30F, DC-10-30F(KC-10A), DC-10-30F(KDC-10), DC-10-40, DC-10-40F, and MD-10-30F
Airplanes. Refer to Paragraph 1.A.1., Airplanes for the list of affected airplanes.
COMPLIANCE
The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to this service
bulletin. The Airworthiness Directive will make the compliance tasks and times given in this service bulletin
mandatory.
Boeing recommends that the inspection and change given in this service bulletin be done within 5 years, after
the original issue date of this service bulletin.
INDUSTRY SUPPORT INFORMATION
Boeing warranty remedies are not available for the inspection and configuration changes given in this service
bulletin.
MANPOWER
Group 1:
Elapsed HoursTotal Task HoursAirplanes
79.5216.0DC-10-30, DC-10-30F and DC-10-30F
(KDC-10)
Group 2:
Elapsed HoursTotal Task HoursAirplanes
74.0248.0DC-10-30F (KC-10A)
Group 3:
Elapsed HoursTotal Task HoursAirplanes
79.5216.0DC-10-30F and MD-10-30F
Group 4:
Elapsed HoursTotal Task HoursAirplanes
79.5216.0DC-10-40 and DC-10-40F
MATERIAL INFORMATION
Boeing Supplied Kits/Parts.
Refer to Paragraph 2.A., Material - Price and Availability.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 25, 2010
DC10-28-244
6 of 130
BOEING SERVICE BULLETIN DC10-28-244

### Page 7 (OCR)

BOEING SERVICE BULLETIN DC10-28-244
INSPECTION AND REPLACEMENT OF WIRE SHIELDING
ABOVE CENTER UPPER AUXILIARY FUEL TANK
1695773
Original Issue: February 25, 2010
BOEING PROPRIETARY -  DC10-28-244
Copyright © Unpublished Work - See page 1 for details.  7 of 130

### Page 8

BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 25, 2010
DC10-28-244
8 of 130
BOEING SERVICE BULLETIN DC10-28-244
BLANK PAGE

### Page 9

Commercial 
Airplanes
DC10
Service Bulletin
Number: DC10-28-244
Original Issue: February 25, 2010
ATA System: 2811
SUBJECT: FUEL - Integral Fuel Tanks - Inspection and Replacement of Wire Shielding above
Center Upper Auxiliary Fuel Tank
1.    PLANNING INFORMATION
A. Effectivity
1. Airplanes
This service bulletin is for the airplanes shown below.
NOTE: When any Group 1 airplane shown below is modified to a freighter configuration by Boeing
Passenger to Freighter (P to F) engineering, it will become a Group 3 airplane.
DESCRIPTIONCONFIGURATIONGROUP
DC-10-30, DC-10-30F and DC-10-30F (KDC-10) Airplanes-1
DC-10-30F (KC-10A) Airplanes-2
DC-10-30F and MD-10-30F Airplanes-3
DC-10-40 and DC-10-40F Airplanes-4
Airplane Models:
DC-10-30, DC-10-30F, DC-10-30F (KC-10A), DC-10-30F (KDC-10), DC-10-40, DC-10-40F,
MD-10-30F
GroupFuselage Num-
ber
1100
3103
1106
3110
1114 - 115
1117
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 25, 2010
DC10-28-244
9 of 130

### Page 10

GroupFuselage Num-
ber
1121 - 123
1127
1129
1131 - 135
1137
1146 - 147
1149 - 150
1152
1156 - 160
1165 - 166
1170 - 171
1174
1178 - 179
1183 - 184
1186 - 190
1192
1195 - 196
1199
1201
1204
4206
1211
4212
1213 - 215
4216
1217
3219
4220
1221
1223
4224
1225 - 227
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 25, 2010
DC10-28-244
10 of 130
BOEING SERVICE BULLETIN DC10-28-244

### Page 11

GroupFuselage Num-
ber
1229
4230
1231 - 232
1234 - 236
1239 - 242
1244 - 246
1248
1253 - 256
3257
1259 - 261
4262
1263 - 264
4265
1266 - 268
4274
1275
3277
1278
1280 - 281
3282
1286 - 293
1295
1299 - 303
4304
1305
4306
4308
4310
2311
1312
4313
1314 - 316
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 25, 2010
DC10-28-244
11 of 130
BOEING SERVICE BULLETIN DC10-28-244

### Page 12

GroupFuselage Num-
ber
3317
1324 - 325
3326
1327
1329
3330
1331 - 332
2333
1334 - 339
4340
1341 - 342
4343
1345
4349
1352
1355 - 356
2359 - 361
2363
1364
4366 - 367
1368 - 370
2373
2375 - 378
2380
4381
2383 - 408
3409
2410 - 411
3412
2413 - 415
3416
2417 - 418
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 25, 2010
DC10-28-244
12 of 130
BOEING SERVICE BULLETIN DC10-28-244

### Page 13

GroupFuselage Num-
ber
1419
2420 - 421
1422
2423 - 432
3433
1434 - 438
2439
3440
2441
3442 - 444
1445 - 446
146
160
163
171
173
182
184
190
396
199
2. Spares Affected
None.
B. Concurrent Requirements
None.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 25, 2010
DC10-28-244
13 of 130
BOEING SERVICE BULLETIN DC10-28-244

### Page 14

C. Reason
Boeing Special Federal Aviation Regulations (SFAR) 88 engineering investigations have determined
that wires routed above the center upper auxiliary fuel tank are in close proximity to the upper surface
of the tank. In addition, some wire harness mounts may have loosened, allowing the wires to contact
the tank. This condition can cause wire damage or chafing that could lead to possible arcing and
sparking on the fuel tank upper surface. Inspection will determine the condition of the wires. Installation
of nonmetallic barrier/shield sleeving, new clamps, and new extruded channels to support the wires
will minimize the possibility of wires contacting the fuel tank upper surface. If not corrected, wires in
contact with the fuel tank could become damaged, and the resulting possible arcing and sparking could
lead to burn-through of the upper surface of the fuel tank and potentially result in an explosion.
This service bulletin resulted from the safety assessments conducted by Boeing under Special Federal
Aviation Regulations (SFAR) 88, Fuel Tank System Fault Tolerance Evaluation Requirements.
D. Description
This service bulletin provides instructions to do as follows:
1. Does a General Visual Inspection of the wire bundles to determine if wires touch the upper surface
of the center upper auxiliary fuel tank and marks those locations.
2. Does a Detailed Inspection of the wires routed above the center upper auxiliary fuel tank for splices
and other damage (such as wire chafing, arcing, and broken insulation) to wire bundles and does
corrective action as necessary.
3. Does a Detailed Inspection of the upper surface of the center upper auxiliary fuel tank for damage
to the fuel barrier seal and does corrective action as necessary.
4. Installs nonmetallic barrier/shield sleeving to the wire harnesses, new clamps, new attaching
hardware, and new extruded channels to raise the wire harnesses off the upper surface of the
center upper auxiliary fuel tank.
This service bulletin assumes that the area above the center upper auxiliary fuel tank is open and
access is available to all the floor beams for maintenance.
The work in this service bulletin is done in the maintenance zone(s) given below.
Group 1:
Affected Maintenance Zones
ZoneModel
141, 142DC-10-30, DC-10-30F, DC-10-
30F (KDC-10)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 25, 2010
DC10-28-244
14 of 130
BOEING SERVICE BULLETIN DC10-28-244

### Page 15

Group 2:
Affected Maintenance Zones
ZoneModel
141, 142DC-10-30F (KC-10A)
Group 3:
Affected Maintenance Zones
ZoneModel
141, 142DC-10-30F, MD-10-30F
Group 4:
Affected Maintenance Zones
ZoneModel
141, 142DC-10-40, DC-10-40F
E. Compliance
The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to
this service bulletin. The Airworthiness Directive will make the compliance tasks and times given in this
service bulletin mandatory.
Boeing recommends that the inspection and change given in this service bulletin be done within 5
years, after the original issue date of this service bulletin.
F. Approval
For MD-10-30F models:
This service bulletin was examined by the Federal Aviation Administration (FAA). The changes specified
in this service bulletin comply with the applicable regulations and are FAA approved. This service
bulletin and its approval were based on the airplane in its original Boeing delivery configuration or as
modified by other approved Boeing changes.
For DC-10-30, DC-10-30F, DC-10-30F (KDC-10), DC-10-30F (KC-10A), DC-10-40 and DC-10-40F
models:
This service bulletin was examined by the Federal Aviation Administration (FAA). The changes specified
in this service bulletin comply with the applicable regulations and are FAA approved, as well as European
Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved
airplanes listed in the service bulletin effectivity. This service bulletin and its approval were based on
the airplane in its original Boeing delivery configuration or as modified by other approved Boeing
changes.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 25, 2010
DC10-28-244
15 of 130
BOEING SERVICE BULLETIN DC10-28-244

### Page 16

If an airplane has a non-Boeing modification or repair that affects a component or system also affected
by this service bulletin, the operator is responsible for obtaining appropriate regulatory agency approval
before incorporating this service bulletin.
G. Manpower
The table below shows an estimate of the task hours necessary to do this change for each airplane.
This estimate is for direct labor only, done by an experienced crew. Adjust the estimate with operator
task hour data if necessary. The estimate does not include lost time. These are some examples of lost
time:
— Time to adjust to the workplace
— Time to schedule the work
— Time to examine the work
— Time to cure the materials
— Time to make the parts
— Time to find the tools.
This service bulletin assumes that the area above the center upper auxiliary fuel tank is open and
access is available to all the floor beams for maintenance.
Group 1:
Elapsed HoursTask HoursNumber of PersonsTask
16.032.02Figures 1, 4
8.016.02Inspect
26.780.03Figures 2 and 5
29.088.03Figures 3 and 6
79.7216.0TOTAL FOR EACH AIRPLANE
Group 2:
Elapsed HoursTask HoursNumber of PersonsTask
16.032.02Figures 7, 4 and 10
8.016.02Inspect
24.096.04Figures 8 and 5
26.0104.04Figures 9 and 6
74.0248.0TOTAL FOR EACH AIRPLANE
Group 3:
Elapsed HoursTask HoursNumber of PersonsTask
16.032.02Figures 11 and 14
8.016.02Inspect
26.780.03Figures 12 and 15
29.088.03Figures 13 and 16
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 25, 2010
DC10-28-244
16 of 130
BOEING SERVICE BULLETIN DC10-28-244

### Page 17

Group 3:
Elapsed HoursTask HoursNumber of PersonsTask
79.7216.0TOTAL FOR EACH AIRPLANE
Group 4:
Elapsed HoursTask HoursNumber of PersonsTask
16.032.02Figures 17 and 4
8.016.02Inspect
26.780.03Figures 18 and 5
29.088.03Figures 19 and 6
79.7216.0TOTAL FOR EACH AIRPLANE
H. Weight and Balance Changes
Group 1:
Moment Change
(MEW) IN.-LBS
Mfr's Empty
Weight (MEW)
LBS
Approximate Sta-
tion (Inches)
Airplane
+30,666.8+23.41308.1DC-10-30, DC-10-30F,
DC-10-30F (KDC-10)
Group 2:
Moment Change
(MEW) IN.-LBS
Mfr's Empty
Weight (MEW)
LBS
Approximate Sta-
tion (Inches)
Airplane
+33,297.5+25.51308.3DC-10-30F (KC-10A)
Group 3:
Moment Change
(MEW) IN.-LBS
Mfr's Empty
Weight (MEW)
LBS
Approximate Sta-
tion (Inches)
Airplane
+25,474.4+19.51307.3DC-10-30F, MD-10-30F
Group 4:
Moment Change
(MEW) IN.-LBS
Mfr's Empty
Weight (MEW)
LBS
Approximate Sta-
tion (Inches)
Airplane
+28,426.2+21.71308.0DC-10-40, DC-10-40F
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 25, 2010
DC10-28-244
17 of 130
BOEING SERVICE BULLETIN DC10-28-244

### Page 18

I. Electrical Load Data
Not changed.
J. References
1. Existing Data:
a. DC-10/MD10 Structural Repair Manual (SRM) 51-42-03.
b. Standard Wiring Practices Manual (SWPM) 20-00-03, 20-00-06, 20-00-13, 20-10-01, 20-10-02,
20-10-03, 20-10-10.
c. DC-10 Special Compliance Item (SCI), Critical Design Configuration Control Limitation
(CDCCL), 20-1, 20-5, 20-6, 20-13.
2. Data supplied with this Service Bulletin:
None.
3. Installation Drawings Used in the Preparation of this Service Bulletin:
ChangeTitleDocument Number
EWire Protection - Above Upper and
Forward Auxiliary Fuel Tank
SR10280056
AEO FWire Protection - Above Upper and
Forward Auxiliary Fuel Tank
SR10280056
AEO GWire Protection - Above Upper and
Forward Auxiliary Fuel Tank
SR10280056
AEO HWire Protection - Above Upper and
Forward Auxiliary Fuel Tank
SR10280056
This drawing was used to prepare this service bulletin. This drawing is not necessary to make the
specified changes, and is not supplied with this service bulletin. This drawing may not be applicable
to all airplane configurations or operators.
K. Publications Affected
1. Publications:
Chapter-SectionPublication
28-11Illustrated Parts Catalog
2. Damage Tolerance Based Structural Inspections:
Boeing has evaluated this service bulletin for effects on Fatigue Critical Structure (FCS) and for
changes to Damage Tolerance Inspections (DTI) required in the Maintenance Program. This
service bulletin does not affect FCS, therefore DTIs are not necessary.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 25, 2010
DC10-28-244
18 of 130
BOEING SERVICE BULLETIN DC10-28-244

### Page 19

L. Interchangeability and Intermixability of Parts
Refer to Paragraph 2.C., Parts Necessary For Each Airplane, for interchangeability and intermixability
information.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 25, 2010
DC10-28-244
19 of 130
BOEING SERVICE BULLETIN DC10-28-244

### Page 20

BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 25, 2010
DC10-28-244
20 of 130
BOEING SERVICE BULLETIN DC10-28-244
BLANK PAGE

### Page 21

2.    MATERIAL INFORMATION
A. Material - Price and Availability
Boeing can supply the kits shown in Paragraph 2.C., Parts Necessary For Each Airplane as shown
below. If there is a limit to the quantity (QTY) of available kits, a supply sequence is given by Spares.
More kits become available as shown in the Reorder Lead Time (ROLT). ROLT is calculated from the
date Boeing gets the purchase order.
Unit Price thru
February 28, 2011
ROLT
(Weeks)
QTYNameKit Number
$13,309.00171SERVICE KITSB10280244-3
16,660.00171SERVICE KITSB10280244-5
12,258.00171SERVICE KITSB10280244-7
12,372.00171SERVICE KITSB10280244-9
The kits are subject to the terms and conditions of the Boeing standard purchase order acknowledgment.
Prices are in United States dollars. Terms: Net 30 days.
Reference this service bulletin and submit your purchase order by one of the methods that
follow:
1. Order on-line via ATA Spec 2000 or Boeing Part Page
2. Fax to (206) 662-7145
3. Spares Customer Support - MC 36-65
Boeing Spares Department
P.O. Box 3707
Seattle, Washington 98124-2207 USA
B. Industry Support Information
Boeing warranty remedies are not available for the inspection and configuration changes given in this
service bulletin.
C. Parts Necessary For Each Airplane
1. Kits/Parts:
NOTE: One Service kit and the items shown in Paragraph 2.C.2., Parts and Materials Supplied
by the Operator, are necessary for each airplane. The Service Kit is divided into Figure
Kits for each installation figure shown in the table below.
To get the kits/parts shown below, refer to Paragraph 2.A., Material - Price and Availability.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 25, 2010
DC10-28-244
21 of 130
BOEING SERVICE BULLETIN DC10-28-244

### Page 22

Figure Kit
986532Top Kit
--1111SB10280244-3
1111--SB10280244-5
------SB10280244-7
--11--SB10280244-9
Figure Kit
181615131210Top Kit
------SB10280244-3
-----1SB10280244-5
-1111-SB10280244-7
1-----SB10280244-9
Figure Kit
19Top Kit
-SB10280244-3
-SB10280244-5
-SB10280244-7
1SB10280244-9
Group 1:
KIT SB10280244-3
NOTES
Existing Part
NumberName
Figure
New Part Number
6532
QTY
SCREW26173D0005-3-10
SCREW27283D0005-3-12
STA-STRAP64569D0254-1-1-9
WASHER8073NAS1252-10L
EXTRUDED
CHANNEL
88NMC05118
CLAMP23S7934111-10SA
CLAMP8S7934111-11SA
CLAMP16S7934111-18SA
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 25, 2010
DC10-28-244
22 of 130
BOEING SERVICE BULLETIN DC10-28-244

### Page 23

Group 1:
KIT SB10280244-3
NOTES
Existing Part
NumberName
Figure
New Part Number
6532
QTY
CLAMP5S7934111-1SA
CLAMP16S7934111-22SA
CLAMP3S7934111-3SA
CLAMP13S7934111-4SA
CLAMP3S7934111-5SA
CLAMP15S7934111-6SA
CLAMP4016S7934111-9SA
SLEEVE2SR10280056-11
SLEEVE2SR10280056-13
SLEEVE11SR10280056-3
SLEEVE21SR10280056-5
SLEEVE2SR10280056-7
SLEEVE65SR10280056-9
Group 2:
KIT SB10280244-5
NOTES
Existing Part
NumberName
Figure
New Part Number
109865
QTY
SCREW850263D0005-3-10
SCREW728273D0005-3-12
STA-STRAP88649D0254-1-1-9
CLAMP11JM44SP4H302RG
WASHER2210680NAS1252-10L
EXTRUDED
CHANNEL
168NMC05118
CLAMP23S7934111-10SA
CLAMP168S7934111-11SA
CLAMP16S7934111-18SA
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 25, 2010
DC10-28-244
23 of 130
BOEING SERVICE BULLETIN DC10-28-244

### Page 24

Group 2:
KIT SB10280244-5
NOTES
Existing Part
NumberName
Figure
New Part Number
109865
QTY
CLAMP5S7934111-1SA
CLAMP16S7934111-22SA
CLAMP3S7934111-3SA
CLAMP13S7934111-4SA
CLAMP19S7934111-5SA
CLAMP15S7934111-6SA
CLAMP1640S7934111-9SA
SLEEVE2SR10280056-11
SLEEVE2SR10280056-13
SLEEVE11SR10280056-3
SLEEVE32SR10280056-5
SLEEVE22SR10280056-7
SLEEVE76SR10280056-9
Group 3:
KIT SB10280244-7
NOTES
Existing Part
NumberName
Figure
New Part Number
16151312
QTY
SCREW27173D0005-3-10
SCREW21283D0005-3-12
STA-STRAP56569D0254-1-1-9
WASHER6975NAS1252-10L
EXTRUDED
CHANNEL
88NMC05118
CLAMP23S7934111-10SA
CLAMP8S7934111-11SA
CLAMP168S7934111-18SA
CLAMP16S7934111-22SA
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 25, 2010
DC10-28-244
24 of 130
BOEING SERVICE BULLETIN DC10-28-244

### Page 25

Group 3:
KIT SB10280244-7
NOTES
Existing Part
NumberName
Figure
New Part Number
16151312
QTY
CLAMP13S7934111-4SA
CLAMP3S7934111-5SA
CLAMP15S7934111-6SA
CLAMP328S7934111-9SA
SLEEVE2SR10280056-11
SLEEVE2SR10280056-13
SLEEVE21SR10280056-5
SLEEVE2SR10280056-7
SLEEVE55SR10280056-9
Group 4:
KIT SB10280244-9
NOTES
Existing Part
NumberName
Figure
New Part Number
191865
QTY
SCREW17263D0005-3-10
SCREW36273D0005-3-12
STA-STRAP72649D0254-1-1-9
WASHER8980NAS1252-10L
EXTRUDED
CHANNEL
168NMC05118
CLAMP31S7934111-10SA
CLAMP8S7934111-11SA
CLAMP16S7934111-18SA
CLAMP5S7934111-1SA
CLAMP16S7934111-22SA
CLAMP3S7934111-3SA
CLAMP813S7934111-4SA
CLAMP3S7934111-5SA
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 25, 2010
DC10-28-244
25 of 130
BOEING SERVICE BULLETIN DC10-28-244

### Page 26

Group 4:
KIT SB10280244-9
NOTES
Existing Part
NumberName
Figure
New Part Number
191865
QTY
CLAMP15S7934111-6SA
CLAMP1640S7934111-9SA
SLEEVE2SR10280056-11
SLEEVE2SR10280056-13
SLEEVE11SR10280056-3
SLEEVE22SR10280056-5
SLEEVE2SR10280056-7
SLEEVE66SR10280056-9
2. Parts and Materials Supplied by the Operator:
NotesNameQTYPart Number/ Specification
(a) (c)TIE TAPE1 RollSR10280056-15
DMS 2089
(18XTZ), (23XTZ)
(b) (c)TAPE4 RollsSR10280056-17
DMS 2186 Type 2
or
950C4874
(a) Can be purchased from: Gudenbrod, Incorporated, 274 Shoemaker Road, Pottstown,
Pennsylvania 19464, CAGE 82110
(b) Can be purchased from: Kirkhill-TA Company, 300 East Cypress Avenue, Brea, California
92821-4007, CAGE: 75345
(c) Or approved Equivalent.
3. Parts Modified and Reidentified:
None.
4. Parts Removed and Not Replaced:
NotesQTYNameExisting Part Number
8CLAMPMS21919WDG3
8CLAMPMS21919WDG8
(a) Keep the part if there are other uses for it.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 25, 2010
DC10-28-244
26 of 130
BOEING SERVICE BULLETIN DC10-28-244

### Page 27

D. Parts Necessary to Change Spares
None.
E. Special Tooling - Price and Availability
None.
F. Special Tooling Necessary to do this Service Bulletin
No special tools or equipment are necessary to do the change in this service bulletin. But, maintenance
and overhaul tools in the manuals given in Paragraph 1.J., References, can be necessary. Examine
operator tool supply to make sure all necessary tools are available.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 25, 2010
DC10-28-244
27 of 130
BOEING SERVICE BULLETIN DC10-28-244

### Page 28

BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 25, 2010
DC10-28-244
28 of 130
BOEING SERVICE BULLETIN DC10-28-244
BLANK PAGE

### Page 29

3.    ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL INFORMATION
WARNING: IF ELECTRICAL POWER IS APPLIED TO THE AIRPLANE, MAKE SURE YOU OBEY
ALL PRECAUTIONS WHILE YOU DO WORK. IF YOU DO NOT OBEY THE
PRECAUTIONS, DEATH OR INJURY TO PERSONS, AND DAMAGE TO THE AIRPLANE
CAN OCCUR.
CAUTION: KEEP THE WORK AREA, WIRES AND ELECTRICAL BUNDLES CLEAN OF METAL
PARTICLES OR CONTAMINATION WHEN YOU USE TOOLS. UNWANTED MATERIAL,
METAL PARTICLES OR CONTAMINATION CAUGHT IN WIRE BUNDLES CAN CAUSE
DAMAGE TO THE BUNDLES. DAMAGED WIRE BUNDLES CAN CAUSE SPARKS OR
OTHER ELECTRICAL DAMAGE.
CAUTION: ELECTRICALLY GROUND THE AIRPLANE. THIS WILL HELP TO PREVENT DAMAGE
TO THE AIRPLANE OR EQUIPMENT.
NOTE: 1. The instructions identified in Paragraph 3.B., Work Instructions and the Figure(s)
give the recommended sequence of steps. The sequence of steps to do this service
bulletin can be changed.
2. Manual titles are referred to by acronyms. Refer to Paragraph 1.J., References, for
definition of the acronyms.
3. Equivalent parts are listed in the AEPL, Drawing 7595071.
4. Use the approved fastener and process material substitutions, in accordance with
DC10/MD10 SRM 51. .
5. If the length of any fastener specified in this service bulletin does not meet the
installation standards in SRM Chapter 51, then a fastener of the same specification,
or an approved substitute, with a length which meets the installation standards in
SRM Chapter 51 may be used.
6. A 1/8-inch thick stack of the same type washers called for in this service bulletin is
the maximum thickness which may be used under fastener head or nut to counteract
accumulation of tolerances.
EXCEPTION: When the available fastener length increments are greater than
1/16-inch, a 3/16-inch thick stack of the same type washers may be used.
7. Unless shown differently, these dimensions and tolerances are used:
– Linear dimensions are in inches
– Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus
or minus 0.03 inch.
– Tolerance on rivet and bolt edge margin is plus or minus 0.05 inch
– Angular tolerance is plus or minus 2 degrees
– Hole dimensions for standard solid rivets are in DC-10/MD10 SRM, Chapter 51
– Torque limits to tighten nuts and bolts are in DC-10/MD10 SRM, Chapter 51.
8. Obey all of the warnings and cautions given in the specified manual sections.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 25, 2010
DC10-28-244
29 of 130
BOEING SERVICE BULLETIN DC10-28-244

### Page 30

9. A Detailed Inspection is defined as: An intensive examination of a specific item,
installation, or assembly to detect damage, failure, or irregularity. Available lighting
is normally supplemented with a direct source of good lighting at an intensity deemed
appropriate. Inspection aids such as mirrors, magnifying lenses, etc. may be
necessary. Surface cleaning and elaborate procedures may be required.
10. A General Visual Inspection is defined as: A visual examination of an interior or
exterior area, installation or assembly to detect obvious damage, failure or irregularity.
This level of inspection is made from within touching distance unless otherwise
specified. A mirror may be necessary to ensure visual access to all surfaces in the
inspection area. This level of inspection is made under normal available lighting
conditions such as daylight, hangar lighting, flashlight or drop-light and may require
removal or opening of access panels or doors. Stands, ladders or platforms may be
required to gain proximity to the area being checked.
11. These work instructions refer to procedures included in other Boeing documents.
When the words "refer to" are used and the operator has an accepted alternative
procedure, the accepted alternative procedure can be used. When the words "in
accordance with" are included in the instruction, the procedure in the Boeing document
must be used.
12. Refer to these SWPM chapters as accepted procedures for applicable operations:
SubjectChapter
Identification of Electrical Wire - CommercialSWPM 20-00-03
Inspection Instructions for Standard Wiring InstallationsSWPM 20-00-06
Electrical Wire CodesSWPM 20-10-01
Wiring Installation - Maintenance PracticesSWPM 20-10-01
Shielding -Maintenance PracticesSWPM 20-10-02
Wire Splicing - Maintenance PracticesSWPM 20-10-03
Wire Harness and Component - CleaningSWPM 20-10-10
13. This service bulletin assumes that the area above the center upper auxiliary fuel tank
is open and access is available to all the floor beams for maintenance.
14. Power feeder cable splices and all other wire splices located over the center upper
auxiliary fuel tanks between Stations Y=1218.950 and Y=1381.000 must be relocated
and repaired in accordance with work Instructions below.
15. Installation of Barrier/Shield sleeving will start 2 inches (+/- 1 inch) away from station
1218.950 aft side and will end 2 inches (+/- 1 inch) away from Station 1381.000
forward side.
16. Install clamps to ensure a friction fit on wire bundles to prevent movement within the
clamp when moderate pressure is applied. It is permissible to use smaller or larger
size clamps of the same type in order to meet this requirement. Refer to SWPM
20-10-01 and SWPM 20-10-02 as accepted procedures.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 25, 2010
DC10-28-244
30 of 130
BOEING SERVICE BULLETIN DC10-28-244

### Page 31

17. Rotate clamps if necessary to eliminate preloading of support brackets.
18. If a power feeder cable or wire splice is located within the area of the sleeving/tape
installations, the following instructions must be applied.
 Remove any existing protective covering (sleeving, tape or tubing) from affected
wire bundles.
 Clean wire bundles. Refer to SWPM 20-10-10 as an accepted procedure.
 Inspect and verify location of any wire splices within affected wire bundles.
 Existing and/or new wire splices shall be relocated/located as follows:
– Wire splices located in an area where protective covering (sleeving, tubing
or tape) is to be installed.
Relocate splice at least 6.0 inches beyond end(s) of where protective
covering is to be installed. Select wire code 801 (DMS 2426, copper wires)
or wire code 98 (DMS 2339, aluminum wires) with appropriate length. Refer
to SWPM 20-00-13 as an accepted procedure. Cut and identify new cable.
Refer to SWPM 20-00-03 as an accepted procedure.
– Wire splices installed above fuel tank.
Relocate spices involving 10 gauge and larger (10, 8, 6 or 4 wire gauges)
to locations at least 3 feet or 2 wire supports (whichever is further) from the
fuel tank boundaries. Select wire code 801 (DMS 2426, copper wires) or
wire code 98 (DMS 2339, aluminum wires) with appropriate length. Refer
to SWPM 20-00-13 as an accepted procedure. Cut and identify new cable.
Refer to SWPM 20-00-03 as an accepted procedure.
19. Replacement or repair of wiring within 6.0 inches of fuel tanks and fuel pipes must
use existing or new wire routing and clipping established in accordance with this
Service Bulletin.
20. Do not use the "Boeing installed wire types" in accordance with SWPM 20-00-13 as
replacement or repair wiring inside or within 6.0 inches of the fuel tanks or fuel pipes.
Use the "Boeing replacement wire types" as replacement or repair wiring inside fuel
tanks or within 6.0 inches of fuel pipes. Refer to SWPM 20-00-13 as an accepted
procedure.
21. Replacement or repair of wiring used within 6.0 inches of fuel tanks and fuel pipes
must use the exact same wire gauge as the type design.
22. Do an electrical continuity test as required after the repair or replacement of wires
and replacement of wire splices.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 25, 2010
DC10-28-244
31 of 130
BOEING SERVICE BULLETIN DC10-28-244

### Page 32

B. WORK INSTRUCTIONS
Group 1:
1. Do a General Visual Inspection of wire bundles routed above the center upper auxiliary fuel tank
between floor beams at Stations Y=1238.950 to Y=1361.000 to determine if wires touch the upper
surface of the fuel tank. Mark the location(s) where the wire bundle(s) contacts the upper surface
of the fuel tank as applicable.
2. Remove all wire harness clamps from overwing floor beams and remove all TC92 wire harness
mounts from wire bundles between the floor beams from Station Y=1238.950 to Y=1361.000, in
accordance with the figures listed in the Table that follows:
FigureArea
1Left Side
4Right Side
3. Clean all wire bundles between the floor beams. Refer to SWPM 20-10-10 as an accepted
procedure.
4. Do a Detailed Inspection of all wire bundles above the center upper auxiliary fuel tank between
Stations Y=1218.950 and Y=1381.000, from X=-40 to X=-90 (right side) and X=15 to X=85 (left
side), for the presence of wires splices and damage such as chafing, arcing, broken insulation, or
burn marks on the upper surface of the center upper auxiliary fuel tank / fuel vapor barrier seal.
Based on inspection findings, do as follows:
NOTE: Pay special attention to areas where wires were in contact with the upper surface of the
fuel tank (marked in step 1).
Condition 1 - No Damage and no Splices Found
a. No more work is necessary. Proceed to Step 5.
Condition 2 - Damage Found on Wire Bundles, No Damage to Upper Surface of Auxiliary
Fuel Tank / Fuel Vapor Barrier Seal
a. Repair/replace damaged wires. Refer to SWPM 20-10-01 and SWPM 20-10-03 as accepted
procedures.
Condition 3 - Splices Found on Power Feeder Wires or Non-Power Feeder Wires
a. Remove and relocate each splice to a location at least 3 feet or 2 wire supports, whichever
is further, away from fuel tank boundaries. Refer to SWPM 20-10-01 and SWPM 20-10-03 as
accepted procedures.
b. Identify new wire. Refer to SWPM 20-00-03 as an accepted procedure.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 25, 2010
DC10-28-244
32 of 130
BOEING SERVICE BULLETIN DC10-28-244

### Page 33

Condition 4 - Damage Found on Wire bundles and Damage Found on Fuel Vapor Barrier
Seal of Auxiliary Fuel Tank
a. Repair Fuel Vapor Barrier Seal in accordance with DC-10, MD-10 SRM 51-42-03.
b. Repair/replace wire(s) causing damage. Refer to SWPM 20-10-01 and SWPM 20-10-03 as
accepted procedures.
Condition 5 - Damage Found on Upper Surface of Center Upper Auxiliary Fuel Tank
a. Contact Boeing for repair instructions and do the repair:
Boeing - Long Beach Division
P.O. Box 1771
Long Beach, California 90801
ATTN: Senior Manager
Technical and Fleet Support
Structures/Airframe Division
Service Engineering
(Service Bulletin DC10-28-244)
5. Install barrier/shield sleeving P/N SR10280056-( ), from Stations Y=1221.000 to Y=1379.000, in
accordance with the figures listed in the table that follows:
FigureArea
2Left Side
5Right Side
6. Install new clamps and extruded channel from Stations Y=1238.950 to Y=1381.000, in accordance
with the figures listed in the table that follows:
FigureArea
3Left Side
6Right Side
7. Put the airplane back to a serviceable condition.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 25, 2010
DC10-28-244
33 of 130
BOEING SERVICE BULLETIN DC10-28-244

### Page 34

Group 2:
1. Do a General Visual Inspection of wire bundles routed above the center upper auxiliary fuel tank
between floor beams at Stations Y=1238.950 to Y=1361.000 to determine if wires touch the upper
surface of the fuel tank. Mark the location(s) where the wire bundle(s) contacts the upper surface
of the fuel tank as applicable.
2. Remove all wire harness clamps from overwing floor beams and remove all TC92 wire harness
mounts from wire bundles from the floor beams between Stations Y=1238.950 to Y=1361.000 in
accordance with figures listed in the table that follows:
FigureArea
7Left Side
4Right Side
3. Clean all wire bundles. Refer to SWPM 20-10-10 as an accepted procedure.
4. Do a Detailed Inspection of all wire bundles above the center upper auxiliary fuel tank between
Stations Y=1218.950 and Y=1381.000, from X=-40 to X=-90 (right side) and X=15 to X=85 (left
side), for the presence of wires splices and damage such as chafing, arcing, broken insulation, or
burn marks on the upper surface of the center upper auxiliary fuel tank / fuel vapor barrier seal.
Based on inspection findings, do as follows:
NOTE: Pay special attention to areas where wires were in contact with the upper surface of the
fuel tank (marked in step 1).
Condition 1 - No Damage and no Splices Found
a. No more work is necessary. Proceed to Step 5.
Condition 2 - Damage Found on Wire Bundles, No Damage to Upper Surface of Auxiliary
Fuel Tank / Fuel Vapor Barrier Seal
a. Repair/replace damaged wires. Refer to SWPM 20-10-01 and SWPM 20-10-03 as accepted
procedures.
Condition 3 - Splices Found on Power Feeder Wires or Non-Power Feeder Wires
a. Remove and relocate the splice to a location at least 3 feet or 2 wire supports, whichever is
further, away from fuel tank boundaries. Refer to SWPM 20-10-01 and SWPM 20-10-03 as
accepted procedures.
b. Identify new cable or wire. Refer to SWPM 20-00-03 as an accepted procedure.
Condition 4 - Damage Found on Wire Bundles and Damage Found on Fuel Vapor Barrier
Seal of Auxiliary Fuel Tank
a. Repair Fuel Vapor Barrier Seal in accordance with DC-10, MD-10-10 SRM 51-42-03.
b. Repair/replace wire(s) causing damage. Refer to SWPM 20-10-01 and SWPM 20-10-03 as
accepted procedures.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 25, 2010
DC10-28-244
34 of 130
BOEING SERVICE BULLETIN DC10-28-244

### Page 35

Condition 5 - Damage Found on Upper Surface of Center Upper Auxiliary Fuel Tank
a. Contact Boeing for repair instructions and do the repair:
Boeing - Long Beach Division
P.O. Box 1771
Long Beach, California 90801
ATTN: Senior Manager
Technical and Fleet Support
Structures/Airframe Division
Service Engineering D800-0032
(Service Bulletin DC10-28-244)
5. Install barrier/shield sleeving P/N SR10280056-( ), from Stations Y=1221.000 to Y=1379.000, in
accordance with the figures listed in the table that follows:
FigureArea
8Left Side
5Right Side
6. Install new clamps and extruded channel from Stations Y=1238.950 to Y=1381.000 in accordance
with the figures listed in the table that follows:
FigureArea
9Left Side
6Right Side
7. Remove wire harness clamps, clean, inspect and repair wires as needed, install sleeving, and
install new clamps in the right side forward cargo D section between Stations Y=1039.000 and
Y=1099.000 in accordance with Figure 10.
8. Put the airplane back to a serviceable condition.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 25, 2010
DC10-28-244
35 of 130
BOEING SERVICE BULLETIN DC10-28-244

### Page 36

Group 3:
1. Do a General Visual Inspection of wire bundles routed above the center upper auxiliary fuel tank
between floor beams at Stations Y=1238.950 to Y=1361.000 to determine if wires touch the upper
surface of the center upper auxiliary fuel tank. Mark the location(s) where the wire bundle(s)
contacts the upper surface of the center upper auxiliary fuel tank as applicable.
2. Remove all wire harness clamps from overwing floor beams and remove all TC92 wire harness
mounts from wire bundles from the floor beams at Stations Y=1238.950 to Y=1361.000, in
accordance with figures listed in the table that follows:
FigureArea
11Left Side
14Right Side
3. Clean all wire bundles. Refer to SWPM 20-10-10 as an accepted procedure.
4. Do a Detailed Inspection of all wire bundles above the center upper auxiliary fuel tank between
Stations Y=1219.000 and Y=1381.000, between X=-40 to X=-90 (right side) and X=40 to X=85
(left side), for the presence of wires splices and damage such as chafing, arcing, broken insulation,
or burn marks on the upper surface of the center upper auxiliary fuel tank / Fuel vapor barrier seal.
Based on inspection findings, do as follows:
NOTE: Pay special attention to areas where wires were in contact with the upper surface of the
fuel tank (marked in step 1).
Condition 1 - No Damage and no Splices Found
a. No more work is necessary. Proceed to Step 5.
Condition 2 - Damage Found on Wire Bundles, No Damage to Upper Surface of Auxiliary
Fuel Tank / Fuel Vapor Barrier Seal
a. Repair/replace damaged wires. Refer to SWPM 20-10-01 and SWPM 20-10-03 as acceptable
procedures.
Condition 3 - Splices Found on Power Feeder Wires or Non-Power Feeder Wires
a. Remove and relocate each splice to a location at least 3 feet or 2 wire supports, whichever
is further, away from fuel tank boundaries. Refer to SWPM 20-10-01 and SWPM 20-10-03 as
acceptable procedures.
b. Identify new wire. Refer to SWPM 20-00-03 as an accepted procedure.
Condition 4 - Damage Found on Wire Bundles and Damage Found on Fuel Vapor Barrier
Seal of Auxiliary Fuel Tank
a. Repair Fuel Vapor Barrier Seal in accordance with DC-10, MD-10-10 SRM 51-42-03.
b. Repair/replace wire(s) causing damage. Refer to SWPM 20-10-01 and SWPM 20-10-03 as
accepted procedures.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 25, 2010
DC10-28-244
36 of 130
BOEING SERVICE BULLETIN DC10-28-244

### Page 37

Condition 5 - Damage Found on Upper Surface of Center Upper Auxiliary Fuel Tank
a. Contact Boeing for repair instructions and do the repair.
Boeing - Long Beach Division
P.O. Box 1771
Long Beach, California 90801
ATTN: Senior Manager
Technical and Fleet Support
Structures/Airframe Design
Service Engineering
(Service Bulletin DC10-28-244)
5. Install barrier/shield sleeving P/N SR10280056-( ), from Stations Y=1221.000 to Y=1379.000, in
accordance with the figures listed in the table that follows:
FigureArea
12Left Side
15Right Side
6. Install new clamps and extruded channel from Stations Y=1238.950 to Y=1381.000 in accordance
with the figures listed in the table that follows:
FigureArea
13Left Side
16Right Side
7. Put the airplane back to a serviceable condition.
Group 4:
1. Do a General Visual Inspection of wire bundles routed above the center upper auxiliary fuel tank
between floor beams at Stations Y=1238.950 to Y=1361.000 to determine if wires touch the upper
surface of the center upper auxiliary fuel tank. Mark the location(s) where the wire bundle(s)
contacts the upper surface of the center upper auxiliary fuel tank as applicable.
2. Remove all wire harness clamps from overwing floor beams and remove all TC92 wire harness
mounts from wire bundles from floor beams at Stations Y=1238.950 to Y=1361.000, in accordance
with figures relative to Table below:
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 25, 2010
DC10-28-244
37 of 130
BOEING SERVICE BULLETIN DC10-28-244

### Page 38

FigureArea
17Left Side
4Right Side
3. Clean all wire bundles. Refer to SWPM 20-10-10 as an accepted procedure.
4. Do a Detailed Inspection of all wire bundles above the center upper auxiliary fuel tank between
Stations Y=1219.000 and Y=1381.000, between X=-40 to X=-90 (right side) and X=15 to X=85
(left side), for the presence of wires splices and damage such as chafing, arcing, broken insulation,
or burn marks on the upper surface of the center upper auxiliary fuel tank / fuel vapor barrier seal.
Based on inspection findings, do as follows:
NOTE: Pay special attention to areas where wires were in contact with the upper surface of the
fuel tank (marked in step 1).
Condition 1 - No Damage and no Splices Found
a. No more work is necessary. Proceed to Step 5.
Condition 2 - Damage Found on Wire Bundles, No Damage to Upper Surface of Auxiliary
Fuel Tank / Fuel Vapor Barrier Seal
a. Repair/replace damaged wires. Refer to SWPM 20-10-01 and SWPM 20-10-03 as accepted
procedures.
Condition 3 - Splices Found on Power Feeder Wires or Non-Power Feeder Wires
a. Remove and relocate each splice to a location at least 3 feet or 2 wire supports (whichever
is further), away from fuel tank boundaries. Refer to SWPM 20-10-03 and SWPM 20-10-01
as accepted procedures.
b. Identify new wire. Refer to SWPM 20-00-03 as an accepted procedure.
Condition 4 - Damage Found on Wire Bundles and Damage Found on Fuel Vapor Barrier
Seal of Auxiliary Fuel Tank
a. Repair Fuel Vapor Barrier Seal in accordance with DC-10, MD-10-10 SRM 51-42-03.
b. Repair/replace wire(s) causing damage. Refer to SWPM 20-10-01 and SWPM 20-10-03 as
accepted procedures.
Condition 5 - Damage Found on Upper Surface of Center Upper Auxiliary Fuel Tank
a. Contact Boeing for repair instructions and do the repair.
Boeing - Long Beach Division
P.O. Box 1771
Long Beach, California 90801
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 25, 2010
DC10-28-244
38 of 130
BOEING SERVICE BULLETIN DC10-28-244

### Page 39

ATTN: Senior Manager
Technical and Fleet Support
Structures/Airframe Division
Service Engineering D800-0032
(Service Bulletin DC10-28-244)
5. Install barrier /shield sleeving P/N 10280056-( ), from Stations Y=1221.000 to Y=1379.000, in
accordance with the figures listed in the table that follows:
FigureArea
18Left Side
5Right Side
6. Install new clamps and extruded channel from Stations Y=1238.950 to Y=1381.000 in accordance
with the figures listed in the table that follows:
FigureArea
19Left Side
6Right Side
7. Put the airplane back to a serviceable condition.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 25, 2010
DC10-28-244
39 of 130
BOEING SERVICE BULLETIN DC10-28-244

### Page 40 (OCR)

BOEING SERVICE BULLETIN DC10-28-244
This Figure applies only to: Group 1.
STA
Y=1381.000
AND
SIA
Y=1361.000
STA
Y=1341.000
STA  STA
Y=1305.000  Y=1321.000
STA
Y=1293.750
STA
Y=1275.250
STA
Y=1256.800
STA
Y=1238.950
1694816
FIGURE 1: WIRES ABOVE AUXILIARY FUEL TANK LEFT SIDE - FLOOR BEAM CLAMPS - REMOVAL
(SHEET 1 OF 6)
Original Issue: February 25, 2010
DC10-28-244
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.  40 of 130

### Page 41 (OCR)

BOEING SERVICE BULLETIN DC10-28-244
X=81.000  X=58.000  X=17.000
Z=-19.000 -
B-B
(7 LOCATIONS)
X=81.000  X=60.500
→ D  ~ E  - D  > D
-Z=-19.000
plo
→ D  • E  -D  - D
C-C
D-D  E-E
(3 LOCATIONS)
1694817
FIGURE 1: WIRES ABOVE AUXILIARY FUEL TANK LEFT SIDE - FLOOR BEAM CLAMPS - REMOVAL
(SHEET 2 OF 6)
Original Issue: February 25, 2010
BOEING PROPRIETARY -  DC10-28-244
Copyright © Unpublished Work - See page 1 for details.  41 of 130

### Page 42 (OCR)

BOEING SERVICE BULLETIN DC10-28-244
X=17.000  X=81.000
1—Z=-19.000
10
F-F
X=81.000
STA
Y=1256.800-
STA
Y=1238.950-
I G-G
FIGURE 1: WIRES ABOVE AUXILIARY FUEL TANK LEFT SIDE - FLOOR BEAM CLAMPS - REMOVAL
(SHEET 3 OF 6)
Original Issue: February 25, 2010
BOEING PROPRIETARY -  DC10-28-244
Copyright © Unpublished Work - See page 1 for details.  42 of 130

### Page 43 (OCR)

BOEING SERVICE BULLETIN DC10-28-244
STA
Y=1341.000
STA
Y=1361.000
1882699
FIGURE 1: WIRES ABOVE AUXILIARY FUEL TANK LEFT SIDE - FLOOR BEAM CLAMPS - REMOVAL
(SHEET 4 OF 6)
Original Issue: February 25, 2010
BOEING PROPRIETARY -  DC10-28-244
Copyright © Unpublished Work - See page 1 for details.  43 of 130

### Page 44 (OCR)

BOEING SERVICE BULLETIN DC10-28-244
Y=1381.000
STA
Y=1361.000
Y=1341.000
STA  STA
Y=1305.000  Y=1321.000
STA
Y=1293.750
STA
Y=1275.250
STA
Y=1256.800
STA
Y=1238.950
- MOUNT
TYPICAL  1694836
FIGURE 1: WIRES ABOVE AUXILIARY FUEL TANK LEFT SIDE - FLOOR BEAM CLAMPS - REMOVAL
(SHEET 5 OF 6)
Original Issue: February 25, 2010
DC10-28-244
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.  44 of 130

### Page 45

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for one side of the airplane.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
EAC (A) - 9101, 9108,
9111, AGP9201
8MS25281R9CLAMPRemove1
EAC (B) - 91083MS25281R4CLAMPRemove2
EAJ - 91048MS25281R9CLAMPRemove3
EAN -9111, 91158MS25281R8CLAMPRemove4
EBC (A) - 9102, 9109,
9111, AGP9201
8MS25281R8CLAMPRemove5
EBC (B) - 9109 (a)7MS25281R5CLAMPRemove6
EBJ - 9105, 9111 (a)8MS25281R5CLAMPRemove7
EDC (A) - 9103, 9109,
9111, AGP9201
8MS25281R20CLAMPRemove8
EDC (B) - 91107MS25281R9CLAMPRemove9
EDJ - 9106, 91118MS25281R20CLAMPRemove10
DDZ - 9103 (a)5MS25281R5CLAMPRemove11
Quantity is an estimate -
remove all mounts.
84TC92MOUNTRemove12
(a) The quantity of MS25281R5 clamps is 3 for airplane configuration that has run letter DDZ routed at Station
Y=1341.00. Quantity is 5 if run Letter DDZ is routed at Station Y=1361.
FIGURE 1: WIRES ABOVE AUXILIARY FUEL TANK LEFT SIDE - FLOOR BEAM CLAMPS - REMOVAL
(SHEET 6 OF 6)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 25, 2010
DC10-28-244
45 of 130
BOEING SERVICE BULLETIN DC10-28-244

### Page 46 (OCR)

BOEING SERVICE BULLETIN DC10-28-244
This Figure applies only to: Group 1.
D  STA
Y=1381.000
STA
Y=1361.000
SIA
Y= 1341.000
STA  STA
Y=1305.000  Y=1321.000
STA
Y=1293.750
STA
Y=1275.250
STA
Y=1256.800
STA
Y=1238.950
B
1694839
FIGURE 2: WIRES ABOVE AUXILIARY FUEL TANK LEFT SIDE - BARRIER/SHIELD SLEEVING -
INSTALLATION
(SHEET 1 OF 3)
Original Issue: February 25, 2010
BOEING PROPRIETARY -  DC10-28-244
Copyright © Unpublished Work - See page 1 for details.  46 of 130

### Page 47

FIGURE 2: WIRES ABOVE AUXILIARY FUEL TANK LEFT SIDE - BARRIER/SHIELD SLEEVING -
INSTALLATION
(SHEET 2 OF 3)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 25, 2010
DC10-28-244
47 of 130
BOEING SERVICE BULLETIN DC10-28-244

### Page 48

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for one side of the airplane.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
EAC (A) - 9101, 9108,
9111, AGP9201
1SR10280056-9SLEEVEInstall (New)1
EAC (B) - 91081SR10280056-5SLEEVEInstall (New)2
EAJ - 91041SR10280056-9SLEEVEInstall (New)3
EAN - 9111, 91151SR10280056-9SLEEVEInstall (New)4
EBC (A) - 9102, 9109,
9111, AGP9201
1SR10280056-9SLEEVEInstall (New)5
EBC (B) - 91091SR10280056-7SLEEVEInstall (New)6
EBJ - 9105, 91111SR10280056-7SLEEVEInstall (New)7
EDC (A) - 9103, 9110,
9111, AGP9201
1SR10280056-13SLEEVEInstall (New)8
EDC (B) - 91101SR10280056-9SLEEVEInstall (New)9
EDJ - 9106, 91111SR10280056-13SLEEVEInstall (New)10
DDZ - 9104 (a)1SR10280056-3SLEEVEInstall (New)11
-SR10280056-15TIE TAPEInstall (New)12
(a) SR10280056-3 is installed on run letter DDZ (-9104) at approximately Station 1341 or 1361 only, not
both locations.
FIGURE 2: WIRES ABOVE AUXILIARY FUEL TANK LEFT SIDE - BARRIER/SHIELD SLEEVING -
INSTALLATION
(SHEET 3 OF 3)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 25, 2010
DC10-28-244
48 of 130
BOEING SERVICE BULLETIN DC10-28-244

### Page 49 (OCR)

BOEING SERVICE BULLETIN DC10-28-244
This Figure applies only to: Group 1.
STA
Y=1381.000
AND
·=1361.000
/=1341.00
Y=1305.000  STA  Y=132  SIA  ST  .000
STA
Y=1293.750
STA
Y=1275.250
STA
Y=1256.800
STA
Y=1238.950
1694982
FIGURE 3: WIRES ABOVE AUXILIARY FUEL TANK LEFT SIDE - CLAMPS AND EXTRUDED CHANNEL-
INSTALLATION
(SHEET 1 OF 6)
Original Issue: February 25, 2010
DC10-28-244
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.  49 of 130

### Page 50 (OCR)

BOEING SERVICE BULLETIN DC10-28-244
X=81.000  X=58.000  X=17.000
Z=-19.000 -
5
B-B
(7 LOCATIONS)
X=81.000  X=60.500
→ D  - D
— Z=-19.000
- D  D  D
C-C
D-D  E-E
(3 LOCATIONS)
1694985
FIGURE 3: WIRES ABOVE AUXILIARY FUEL TANK LEFT SIDE - CLAMPS AND EXTRUDED CHANNEL -
INSTALLATION
(SHEET 2 OF 6)
Original Issue: February 25, 2010
BOEING PROPRIETARY -  DC10-28-244
Copyright © Unpublished Work - See page 1 for details.  50 of 130

### Page 51 (OCR)

BOEING SERVICE BULLETIN DC10-28-244
X=17.000  X=81.000
- Z=-19.000
F-F
X=81.000
Y=1256.750 -
STA
Y=1238.950
G-G
1694986
FIGURE 3: WIRES ABOVE AUXILIARY FUEL TANK LEFT SIDE - CLAMPS AND EXTRUDED CHANNEL-
INSTALLATION
(SHEET 3 OF 6)
Original Issue: February 25, 2010
DC10-28-244
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.  51 of 130

### Page 52 (OCR)

BOEING SERVICE BULLETIN DC10-28-244
STA
Y=1341.000.
STA
Y=1361.000-
K
1882718
FIGURE 3: WIRES ABOVE AUXILIARY FUEL TANK LEFT SIDE - CLAMPS AND EXTRUDED CHANNEL -
INSTALLATION
(SHEET 4 OF 6)
Original Issue: February 25, 2010
BOEING PROPRIETARY -  DC10-28-244
Copyright © Unpublished Work - See page 1 for details.  52 of 130

### Page 53 (OCR)

BOEING SERVICE BULLETIN DC10-28-244
STA
Y=1381.000
STA
Y=1361.000
STA
Y=1341.000
Y=1305.000  STA  ·=1521.000
STA
Y=1293.750
STA
Y=1275.250
STA
Y=1256.800
STA
Y=1238.950
13/14
STRAP
EXTRUDED
CHANNEL
TYPICAL  1694987
FIGURE 3: WIRES ABOVE AUXILIARY FUEL TANK LEFT SIDE - CLAMPS AND EXTRUDED CHANNEL -
INSTALLATION
(SHEET 5 OF 6)
Original Issue: February 25, 2010
BOEING PROPRIETARY -  DC10-28-244
Copyright © Unpublished Work - See page 1 for details.  53 of 130

### Page 54

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for one side of the airplane.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
EAC (A ) - 9101, 9108,
9111, AGP9201
8S7934111-10SACLAMPInstall (New)1
EAC (B) - 91083S7934111-5SACLAMPInstall (New)2
EAJ - 91048S7934111-10SACLAMPInstall (New)3
EAN - 9111, 91158S7934111-9SACLAMPInstall (New)4
EBC (A) - 9102, 9109,
9111, AGP9201
8S7934111-9SACLAMPInstall (New)5
EBC (B) - 91097S7934111-6SACLAMPInstall (New)6
EBJ - 9105, 91118S7934111-6SACLAMPInstall (New)7
EDC (A) - 9103, 9110,
9111, AGP9201
8S7934111-22SACLAMPInstall (New)8
EDC (B) - 91107S7934111-10SACLAMPInstall (New)9
EDJ - 9106, 91118S7934111-22SACLAMPInstall (New)10
DDZ - 9104 (a)5S7934111-1SACLAMPInstall (New)11
173D0005-3-10SCREWInstall (New)12
283D0005-3-12SCREWInstall (New)
73NAS1252-10LWASHERInstall (New)
Cut extruded channel to
fit if required. Center ex-
truded channel between
floor beams.
8NMC05118EXTRUDED CHANNELInstall (New)13
569D0254-1-1-9STA-STRAPInstall (New)14
(a) The quantity of S7934111-1 SA clamps is 3 for airplane configuration that has run letter DDZ routed at
Station 1341.00.
FIGURE 3: WIRES ABOVE AUXILIARY FUEL TANK LEFT SIDE - CLAMPS AND EXTRUDED CHANNEL -
INSTALLATION
(SHEET 6 OF 6)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 25, 2010
DC10-28-244
54 of 130
BOEING SERVICE BULLETIN DC10-28-244

### Page 55 (OCR)

BOEING SERVICE BULLETIN DC10-28-244
This Figure applies only to: Group 1-2, 4.
STA
Y=1381.000
AND
Y=13бt.000
STA
Y=1341.000
STA  STA
Y=1321.000  Y=1305.000
STA
Y=1293.750
STA
Y=1275.250
STA
Y=1256.800
STA
Y=1238.950
1694990
FIGURE 4: WIRES ABOVE AUXILIARY FUEL TANK RIGHT SIDE - FLOOR BEAM CLAMPS - REMOVAL
(SHEET 1 OF 5)
Original Issue: February 25, 2010
DC10-28-244
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.  55 of 130

### Page 56 (OCR)

BOEING SERVICE BULLETIN DC10-28-244
X=-46.500  X=-81.000
Z=-19.000
B-B
(7 LOCATIONS)
X=81.000
F  D  • E
-Z=-19.000
F  D  D  • E
C-C
(TO
(10)
D-D  E-E  F-F
(2 LOCATIONS)  1694991
FIGURE 4: WIRES ABOVE AUXILIARY FUEL TANK RIGHT SIDE - FLOOR BEAM CLAMPS - REMOVAL
(SHEET 2 OF 5)
Original issue: February 25, 2010
DC10-28-244
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.  56 of 130

### Page 57 (OCR)

BOEING SERVICE BULLETIN DC10-28-244
X=-81.000  X=-46.500
—Z=-19.000
G-G
X=-81.000
STA
— Y=1256.750
STA
- Y=1239.000
H-H
1694993
FIGURE 4: WIRES ABOVE AUXILIARY FUEL TANK RIGHT SIDE - FLOOR BEAM CLAMPS - REMOVAL
(SHEET 3 OF 5)
Original Issue: February 25, 2010
BOEING PROPRIETARY -  DC10-28-244
Copyright © Unpublished Work - See page 1 for details.  57 of 130

### Page 58 (OCR)

BOEING SERVICE BULLETIN DC10-28-244
STA
Y=1381.000
STA
Y=1361.000
STA
Y=1341.000
STA  STA
Y=1321.000  Y=1305.000
STA
Y=1293.750
STA
Y=1275.250
STA
Y=1256.800
STA
Y=1238.950
12)
- MOUNT
TYPICAL  1694996
FIGURE 4: WIRES ABOVE AUXILIARY FUEL TANK RIGHT SIDE - FLOOR BEAM CLAMPS - REMOVAL
(SHEET 4 OF 5)
Original Issue: February 25, 2010
DC10-28-244
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.  58 of 130

### Page 59

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for one side of the airplane.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
DNR - 92078MS25281R8CLAMPRemove1
EAF - 9204, 9213,
AGP9102
8MS25281R8CLAMPRemove2
EAG - 92083MS25281R2CLAMPRemove3
EAK - 92018MS25281R10CLAMPRemove4
EAP - 2078MS25281R8CLAMPRemove5
EBF - 9205, 9209,
AGP9102
8MS25281R16CLAMPRemove6
EBG - 92096MS25281R3CLAMPRemove7
EBK - 9202, 92138MS25281R8CLAMPRemove8
EDF - 9206, 9210, 92128MS25281R16CLAMPRemove9
EDG - 92106MS25281R3CLAMPRemove10
EDK - 92028MS25281R8CLAMPRemove11
Quantity is an estimate -
remove all mounts.
104TC92MOUNTRemove12
FIGURE 4: WIRES ABOVE AUXILIARY FUEL TANK RIGHT SIDE - FLOOR BEAM CLAMPS - REMOVAL
(SHEET 5 OF 5)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 25, 2010
DC10-28-244
59 of 130
BOEING SERVICE BULLETIN DC10-28-244

### Page 60 (OCR)

BOEING SERVICE BULLETIN DC10-28-244
This Figure applies only to: Group 1-2, 4.
STA
Y=1381.000
STA
Y=1361.000
STA
Y=1341.000
STA  STA
Y=1321.000  Y=1305.000
STA
Y=1293.750
STA
Y=1275.250
STA
Y=1256.800
STA
Y=1238.950
1694999
FIGURE 5: WIRES ABOVE AUXILIARY FUEL TANK RIGHT SIDE - BARRIER/SHIELD SLEEVING -
INSTALLATION
(SHEET 1 OF 3)
Original Issue: February 25, 2010
BOEING PROPRIETARY -  DC10-28-244
Copyright © Unpublished Work - See page 1 for details.  60 of 130

The text continues at https://openairdocs.org/service-documents/boeing/dc10-28-244/file/9d143a7b7336.md?from=61

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
